diff options
Diffstat (limited to 'Documentation/devicetree/bindings/serial')
| -rw-r--r-- | Documentation/devicetree/bindings/serial/8250.txt | 21 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/serial/st,stm32-usart.txt | 46 |
2 files changed, 48 insertions, 19 deletions
diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt index f5561ac7e17e..f86bb06c39e9 100644 --- a/Documentation/devicetree/bindings/serial/8250.txt +++ b/Documentation/devicetree/bindings/serial/8250.txt @@ -42,9 +42,8 @@ Optional properties: - auto-flow-control: one way to enable automatic flow control support. The driver is allowed to detect support for the capability even without this property. -- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD - line respectively. It will use specified GPIO instead of the peripheral - function pin for the UART feature. If unsure, don't specify this property. +- tx-threshold: Specify the TX FIFO low water indication for parts with + programmable TX FIFO thresholds. Note: * fsl,ns16550: @@ -66,19 +65,3 @@ Example: interrupts = <10>; reg-shift = <2>; }; - -Example for OMAP UART using GPIO-based modem control signals: - - uart4: serial@49042000 { - compatible = "ti,omap3-uart"; - reg = <0x49042000 0x400>; - interrupts = <80>; - ti,hwmods = "uart4"; - clock-frequency = <48000000>; - cts-gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; - rts-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>; - dtr-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; - dsr-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; - dcd-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; - rng-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; - }; diff --git a/Documentation/devicetree/bindings/serial/st,stm32-usart.txt b/Documentation/devicetree/bindings/serial/st,stm32-usart.txt new file mode 100644 index 000000000000..85ec5f2b1996 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/st,stm32-usart.txt @@ -0,0 +1,46 @@ +* STMicroelectronics STM32 USART + +Required properties: +- compatible: Can be either "st,stm32-usart", "st,stm32-uart", +"st,stm32f7-usart" or "st,stm32f7-uart" depending on whether +the device supports synchronous mode and is compatible with +stm32(f4) or stm32f7. +- reg: The address and length of the peripheral registers space +- interrupts: The interrupt line of the USART instance +- clocks: The input clock of the USART instance + +Optional properties: +- pinctrl: The reference on the pins configuration +- st,hw-flow-ctrl: bool flag to enable hardware flow control. +- dmas: phandle(s) to DMA controller node(s). Refer to stm32-dma.txt +- dma-names: "rx" and/or "tx" + +Examples: +usart4: serial@40004c00 { + compatible = "st,stm32-uart"; + reg = <0x40004c00 0x400>; + interrupts = <52>; + clocks = <&clk_pclk1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart4>; +}; + +usart2: serial@40004400 { + compatible = "st,stm32-usart", "st,stm32-uart"; + reg = <0x40004400 0x400>; + interrupts = <38>; + clocks = <&clk_pclk1>; + st,hw-flow-ctrl; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart2 &pinctrl_usart2_rtscts>; +}; + +usart1: serial@40011000 { + compatible = "st,stm32-usart", "st,stm32-uart"; + reg = <0x40011000 0x400>; + interrupts = <37>; + clocks = <&rcc 0 164>; + dmas = <&dma2 2 4 0x414 0x0>, + <&dma2 7 4 0x414 0x0>; + dma-names = "rx", "tx"; +}; |