diff options
Diffstat (limited to 'Documentation/devicetree/bindings/sound/cs35l36.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/sound/cs35l36.txt | 168 |
1 files changed, 168 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/sound/cs35l36.txt b/Documentation/devicetree/bindings/sound/cs35l36.txt new file mode 100644 index 000000000000..912bd162b477 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs35l36.txt @@ -0,0 +1,168 @@ +CS35L36 Speaker Amplifier + +Required properties: + + - compatible : "cirrus,cs35l36" + + - reg : the I2C address of the device for I2C + + - VA-supply, VP-supply : power supplies for the device, + as covered in + Documentation/devicetree/bindings/regulator/regulator.txt. + + - cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost + converter's output voltage in mV. The range is from 2550mV to 12000mV with + increments of 50mV. + (Default) VP + + - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA. + Configures the peak current by monitoring the current through the boost FET. + Range starts at 1600mA and goes to a maximum of 4500mA with increments of + 50mA. + (Default) 4.50 Amps + + - cirrus,boost-ind-nanohenry : Inductor estimation LBST reference value. + Seeds the digital boost converter's inductor estimation block with the initial + inductance value to reference. + + 1000 = 1uH (Default) + 1200 = 1.2uH + +Optional properties: + - cirrus,multi-amp-mode : Boolean to determine if there are more than + one amplifier in the system. If more than one it is best to Hi-Z the ASP + port to prevent bus contention on the output signal + + - cirrus,boost-ctl-select : Boost conerter control source selection. + Selects the source of the BST_CTL target VBST voltage for the boost + converter to generate. + 0x00 - Control Port Value + 0x01 - Class H Tracking (Default) + 0x10 - MultiDevice Sync Value + + - cirrus,amp-pcm-inv : Boolean to determine Amplifier will invert incoming + PCM data + + - cirrus,imon-pol-inv : Boolean to determine Amplifier will invert the + polarity of outbound IMON feedback data + + - cirrus,vmon-pol-inv : Boolean to determine Amplifier will invert the + polarity of outbound VMON feedback data + + - cirrus,dcm-mode-enable : Boost converter automatic DCM Mode enable. + This enables the digital boost converter to operate in a low power + (Discontinuous Conduction) mode during low loading conditions. + + - cirrus,weak-fet-disable : Boolean : The strength of the output drivers is + reduced when operating in a Weak-FET Drive Mode and must not be used to drive + a large load. + + - cirrus,classh-wk-fet-delay : Weak-FET entry delay. Controls the delay + (in ms) before the Class H algorithm switches to the weak-FET voltage + (after the audio falls and remains below the value specified in WKFET_AMP_THLD). + + 0 = 0ms + 1 = 5ms + 2 = 10ms + 3 = 50ms + 4 = 100ms (Default) + 5 = 200ms + 6 = 500ms + 7 = 1000ms + + - cirrus,classh-weak-fet-thld-millivolt : Weak-FET amplifier drive threshold. + Configures the signal threshold at which the PWM output stage enters + weak-FET operation. The range is 50mV to 700mV in 50mV increments. + + - cirrus,temp-warn-threshold : Amplifier overtemperature warning threshold. + Configures the threshold at which the overtemperature warning condition occurs. + When the threshold is met, the overtemperature warning attenuation is applied + and the TEMP_WARN_EINT interrupt status bit is set. + If TEMP_WARN_MASK = 0, INTb is asserted. + + 0 = 105C + 1 = 115C + 2 = 125C (Default) + 3 = 135C + + - cirrus,irq-drive-select : Selects the driver type of the selected interrupt + output. + + 0 = Open-drain + 1 = Push-pull (Default) + + - cirrus,irq-gpio-select : Selects the pin to serve as the programmable + interrupt output. + + 0 = PDM_DATA / SWIRE_SD / INT (Default) + 1 = GPIO + +Optional properties for the "cirrus,vpbr-config" Sub-node + + - cirrus,vpbr-en : VBST brownout prevention enable. Configures whether the + VBST brownout prevention algorithm is enabled or disabled. + + 0 = VBST brownout prevention disabled (default) + 1 = VBST brownout prevention enabled + + See Section 7.31.1 VPBR Config for configuration options & further details + + - cirrus,vpbr-thld : Initial VPBR threshold. Configures the VP brownout + threshold voltage + + - cirrus,cirrus,vpbr-atk-rate : Attenuation attack step rate. Configures the + amount delay between consecutive volume attenuation steps when a brownout + condition is present and the VP brownout condition is in an attacking state. + + - cirrus,vpbr-atk-vol : VP brownout prevention step size. Configures the VP + brownout prevention attacking attenuation step size when operating in either + digital volume or analog gain modes. + + - cirrus,vpbr-max-attn : Maximum attenuation that the VP brownout prevention + can apply to the audio signal. + + - cirrus,vpbr-wait : Configures the delay time between a brownout condition + no longer being present and the VP brownout prevention entering an attenuation + release state. + + - cirrus,vpbr-rel-rate : Attenuation release step rate. Configures the delay + between consecutive volume attenuation release steps when a brownout condition + is not longer present and the VP brownout is in an attenuation release state. + + - cirrus,vpbr-mute-en : During the attack state, if the vpbr-max-attn value + is reached, the error condition still remains, and this bit is set, the audio + is muted. + +Example: + +cs35l36: cs35l36@40 { + compatible = "cirrus,cs35l36"; + reg = <0x40>; + VA-supply = <&dummy_vreg>; + VP-supply = <&dummy_vreg>; + reset-gpios = <&gpio0 54 0>; + interrupt-parent = <&gpio8>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + + cirrus,boost-ind-nanohenry = <1000>; + cirrus,boost-ctl-millivolt = <10000>; + cirrus,boost-peak-milliamp = <4500>; + cirrus,boost-ctl-select = <0x00>; + cirrus,weak-fet-delay = <0x04>; + cirrus,weak-fet-thld = <0x01>; + cirrus,temp-warn-threshold = <0x01>; + cirrus,multi-amp-mode; + cirrus,irq-drive-select = <0x01>; + cirrus,irq-gpio-select = <0x01>; + + cirrus,vpbr-config { + cirrus,vpbr-en = <0x00>; + cirrus,vpbr-thld = <0x05>; + cirrus,vpbr-atk-rate = <0x02>; + cirrus,vpbr-atk-vol = <0x01>; + cirrus,vpbr-max-attn = <0x09>; + cirrus,vpbr-wait = <0x01>; + cirrus,vpbr-rel-rate = <0x05>; + cirrus,vpbr-mute-en = <0x00>; + }; +}; |