diff options
Diffstat (limited to 'Documentation/devicetree/bindings/sound')
7 files changed, 209 insertions, 8 deletions
diff --git a/Documentation/devicetree/bindings/sound/ak4104.txt b/Documentation/devicetree/bindings/sound/ak4104.txt index b902ee39cf89..deca5e18f304 100644 --- a/Documentation/devicetree/bindings/sound/ak4104.txt +++ b/Documentation/devicetree/bindings/sound/ak4104.txt @@ -8,6 +8,8 @@ Required properties: - reg : The chip select number on the SPI bus + - vdd-supply : A regulator node, providing 2.7V - 3.6V + Optional properties: - reset-gpio : a GPIO spec for the reset pin. If specified, it will be @@ -19,4 +21,5 @@ spdif: ak4104@0 { compatible = "asahi-kasei,ak4104"; reg = <0>; spi-max-frequency = <5000000>; + vdd-supply = <&vdd_3v3_reg>; }; diff --git a/Documentation/devicetree/bindings/sound/alc5623.txt b/Documentation/devicetree/bindings/sound/alc5623.txt new file mode 100644 index 000000000000..26c86c98d671 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/alc5623.txt @@ -0,0 +1,25 @@ +ALC5621/ALC5622/ALC5623 audio Codec + +Required properties: + + - compatible: "realtek,alc5623" + - reg: the I2C address of the device. + +Optional properties: + + - add-ctrl: Default register value for Reg-40h, Additional Control + Register. If absent or has the value of 0, the + register is untouched. + + - jack-det-ctrl: Default register value for Reg-5Ah, Jack Detect + Control Register. If absent or has value 0, the + register is untouched. + +Example: + + alc5621: alc5621@1a { + compatible = "alc5621"; + reg = <0x1a>; + add-ctrl = <0x3700>; + jack-det-ctrl = <0x4810>; + }; diff --git a/Documentation/devicetree/bindings/sound/cs42l56.txt b/Documentation/devicetree/bindings/sound/cs42l56.txt new file mode 100644 index 000000000000..4feb0eb27ea4 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs42l56.txt @@ -0,0 +1,63 @@ +CS42L52 audio CODEC + +Required properties: + + - compatible : "cirrus,cs42l56" + + - reg : the I2C address of the device for I2C + + - VA-supply, VCP-supply, VLDO-supply : power supplies for the device, + as covered in Documentation/devicetree/bindings/regulator/regulator.txt. + +Optional properties: + + - cirrus,gpio-nreset : GPIO controller's phandle and the number + of the GPIO used to reset the codec. + + - cirrus,chgfreq-divisor : Values used to set the Charge Pump Frequency. + Allowable values of 0x00 through 0x0F. These are raw values written to the + register, not the actual frequency. The frequency is determined by the following. + Frequency = MCLK / 4 * (N+2) + N = chgfreq_val + MCLK = Where MCLK is the frequency of the mclk signal after the MCLKDIV2 circuit. + + - cirrus,ain1a-ref-cfg, ain1b-ref-cfg : boolean, If present, AIN1A or AIN1B are configured + as a pseudo-differential input referenced to AIN1REF/AIN3A. + + - cirrus,ain2a-ref-cfg, ain2b-ref-cfg : boolean, If present, AIN2A or AIN2B are configured + as a pseudo-differential input referenced to AIN2REF/AIN3B. + + - cirrus,micbias-lvl: Set the output voltage level on the MICBIAS Pin. + 0 = 0.5 x VA + 1 = 0.6 x VA + 2 = 0.7 x VA + 3 = 0.8 x VA + 4 = 0.83 x VA + 5 = 0.91 x VA + + - cirrus,adaptive-pwr-cfg : Configures how the power to the Headphone and Lineout + Amplifiers adapt to the output signal levels. + 0 = Adapt to Volume Mode. Voltage level determined by the sum of the relevant volume settings. + 1 = Fixed - Headphone and Line Amp supply = + or - VCP/2. + 2 = Fixed - Headphone and Line Amp supply = + or - VCP. + 3 = Adapted to Signal; Voltage level is dynamically determined by the output signal. + + - cirrus,hpf-left-freq, hpf-right-freq : Sets the corner frequency (-3dB point) for the internal High-Pass + Filter. + 0 = 1.8Hz + 1 = 119Hz + 2 = 236Hz + 3 = 464Hz + + +Example: + +codec: codec@4b { + compatible = "cirrus,cs42l56"; + reg = <0x4b>; + gpio-reset = <&gpio 10 0>; + cirrus,chgfreq-divisor = <0x05>; + cirrus.ain1_ref_cfg; + cirrus,micbias-lvl = <5>; + VA-supply = <®_audio>; +}; diff --git a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt index 569b26c4a81e..60ca07996458 100644 --- a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt +++ b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt @@ -47,7 +47,7 @@ mcasp0: mcasp0@1d00000 { reg = <0x100000 0x3000>; reg-names "mpu"; interrupts = <82>, <83>; - interrupts-names = "tx", "rx"; + interrupt-names = "tx", "rx"; op-mode = <0>; /* MCASP_IIS_MODE */ tdm-slots = <2>; serial-dir = < diff --git a/Documentation/devicetree/bindings/sound/fsl-sai.txt b/Documentation/devicetree/bindings/sound/fsl-sai.txt index 98611a6761c0..0f4e23828190 100644 --- a/Documentation/devicetree/bindings/sound/fsl-sai.txt +++ b/Documentation/devicetree/bindings/sound/fsl-sai.txt @@ -7,10 +7,11 @@ codec/DSP interfaces. Required properties: -- compatible: Compatible list, contains "fsl,vf610-sai". +- compatible: Compatible list, contains "fsl,vf610-sai" or "fsl,imx6sx-sai". - reg: Offset and length of the register set for the device. - clocks: Must contain an entry for each entry in clock-names. -- clock-names : Must include the "sai" entry. +- clock-names : Must include the "bus" for register access and "mclk1" "mclk2" + "mclk3" for bit clock and frame clock providing. - dmas : Generic dma devicetree binding as described in Documentation/devicetree/bindings/dma/dma.txt. - dma-names : Two dmas have to be defined, "tx" and "rx". @@ -30,8 +31,10 @@ sai2: sai@40031000 { reg = <0x40031000 0x1000>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_sai2_1>; - clocks = <&clks VF610_CLK_SAI2>; - clock-names = "sai"; + clocks = <&clks VF610_CLK_PLATFORM_BUS>, + <&clks VF610_CLK_SAI2>, + <&clks 0>, <&clks 0>; + clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 0 VF610_EDMA_MUXID0_SAI2_TX>, <&edma0 0 VF610_EDMA_MUXID0_SAI2_RX>; diff --git a/Documentation/devicetree/bindings/sound/st,sta350.txt b/Documentation/devicetree/bindings/sound/st,sta350.txt new file mode 100644 index 000000000000..950188891abd --- /dev/null +++ b/Documentation/devicetree/bindings/sound/st,sta350.txt @@ -0,0 +1,107 @@ +STA350 audio CODEC + +The driver for this device only supports I2C. + +Required properties: + + - compatible: "st,sta350" + - reg: the I2C address of the device for I2C + - reset-gpios: a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the codec starts. + + - power-down-gpios: a GPIO spec for the power down pin. If specified, + it will be deasserted before communication to the codec + starts. + + - vdd-dig-supply: regulator spec, providing 3.3V + - vdd-pll-supply: regulator spec, providing 3.3V + - vcc-supply: regulator spec, providing 5V - 26V + +Optional properties: + + - st,output-conf: number, Selects the output configuration: + 0: 2-channel (full-bridge) power, 2-channel data-out + 1: 2 (half-bridge). 1 (full-bridge) on-board power + 2: 2 Channel (Full-Bridge) Power, 1 Channel FFX + 3: 1 Channel Mono-Parallel + If parameter is missing, mode 0 will be enabled. + + - st,ch1-output-mapping: Channel 1 output mapping + - st,ch2-output-mapping: Channel 2 output mapping + - st,ch3-output-mapping: Channel 3 output mapping + 0: Channel 1 + 1: Channel 2 + 2: Channel 3 + If parameter is missing, channel 1 is choosen. + + - st,thermal-warning-recover: + If present, thermal warning recovery is enabled. + + - st,thermal-warning-adjustment: + If present, thermal warning adjustment is enabled. + + - st,fault-detect-recovery: + If present, then fault recovery will be enabled. + + - st,ffx-power-output-mode: string + The FFX power output mode selects how the FFX output timing is + configured. Must be one of these values: + - "drop-compensation" + - "tapered-compensation" + - "full-power-mode" + - "variable-drop-compensation" (default) + + - st,drop-compensation-ns: number + Only required for "st,ffx-power-output-mode" == + "variable-drop-compensation". + Specifies the drop compensation in nanoseconds. + The value must be in the range of 0..300, and only + multiples of 20 are allowed. Default is 140ns. + + - st,overcurrent-warning-adjustment: + If present, overcurrent warning adjustment is enabled. + + - st,max-power-use-mpcc: + If present, then MPCC bits are used for MPC coefficients, + otherwise standard MPC coefficients are used. + + - st,max-power-corr: + If present, power bridge correction for THD reduction near maximum + power output is enabled. + + - st,am-reduction-mode: + If present, FFX mode runs in AM reduction mode, otherwise normal + FFX mode is used. + + - st,odd-pwm-speed-mode: + If present, PWM speed mode run on odd speed mode (341.3 kHz) on all + channels. If not present, normal PWM spped mode (384 kHz) will be used. + + - st,distortion-compensation: + If present, distortion compensation variable uses DCC coefficient. + If not present, preset DC coefficient is used. + + - st,invalid-input-detect-mute: + If not present, automatic invalid input detect mute is enabled. + + + +Example: + +codec: sta350@38 { + compatible = "st,sta350"; + reg = <0x1c>; + reset-gpios = <&gpio1 19 0>; + power-down-gpios = <&gpio1 16 0>; + st,output-conf = <0x3>; // set output to 2-channel + // (full-bridge) power, + // 2-channel data-out + st,ch1-output-mapping = <0>; // set channel 1 output ch 1 + st,ch2-output-mapping = <0>; // set channel 2 output ch 1 + st,ch3-output-mapping = <0>; // set channel 3 output ch 1 + st,max-power-correction; // enables power bridge + // correction for THD reduction + // near maximum power output + st,invalid-input-detect-mute; // mute if no valid digital + // audio signal is provided. +}; diff --git a/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt b/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt index 74c66dee3e14..eff12be5e789 100644 --- a/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt +++ b/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt @@ -13,6 +13,9 @@ Required properties: "ti,tlv320aic3111" - TLV320AIC3111 (stereo speaker amp, MiniDSP) - reg - <int> - I2C slave address +- HPVDD-supply, SPRVDD-supply, SPLVDD-supply, AVDD-supply, IOVDD-supply, + DVDD-supply : power supplies for the device as covered in + Documentation/devicetree/bindings/regulator/regulator.txt Optional properties: @@ -24,9 +27,6 @@ Optional properties: 3 or MICBIAS_AVDD - MICBIAS output is connected to AVDD If this node is not mentioned or if the value is unknown, then micbias is set to 2.0V. -- HPVDD-supply, SPRVDD-supply, SPLVDD-supply, AVDD-supply, IOVDD-supply, - DVDD-supply : power supplies for the device as covered in - Documentation/devicetree/bindings/regulator/regulator.txt CODEC output pins: * HPL |