diff options
Diffstat (limited to 'Documentation/devicetree/bindings/sound')
6 files changed, 140 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/sound/ak5386.txt b/Documentation/devicetree/bindings/sound/ak5386.txt index dc3914fe6ce8..ec3df3abba0c 100644 --- a/Documentation/devicetree/bindings/sound/ak5386.txt +++ b/Documentation/devicetree/bindings/sound/ak5386.txt @@ -10,10 +10,14 @@ Optional properties: - reset-gpio : a GPIO spec for the reset/power down pin. If specified, it will be deasserted at probe time. + - va-supply : a regulator spec, providing 5.0V + - vd-supply : a regulator spec, providing 3.3V Example: spdif: ak5386@0 { compatible = "asahi-kasei,ak5386"; reset-gpio = <&gpio0 23>; + va-supply = <&vdd_5v0_reg>; + vd-supply = <&vdd_3v3_reg>; }; diff --git a/Documentation/devicetree/bindings/sound/cs4265.txt b/Documentation/devicetree/bindings/sound/cs4265.txt new file mode 100644 index 000000000000..380fff8e4e83 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs4265.txt @@ -0,0 +1,29 @@ +CS4265 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "cirrus,cs4265" + + - reg : the I2C address of the device for I2C. The I2C address depends on + the state of the AD0 pin. If AD0 is high, the i2c address is 0x4f. + If it is low, the i2c address is 0x4e. + +Optional properties: + + - reset-gpios : a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the codec starts. + +Examples: + +codec_ad0_high: cs4265@4f { /* AD0 Pin is high */ + compatible = "cirrus,cs4265"; + reg = <0x4f>; +}; + + +codec_ad0_low: cs4265@4e { /* AD0 Pin is low */ + compatible = "cirrus,cs4265"; + reg = <0x4e>; +}; diff --git a/Documentation/devicetree/bindings/sound/fsl,asrc.txt b/Documentation/devicetree/bindings/sound/fsl,asrc.txt new file mode 100644 index 000000000000..b93362a570be --- /dev/null +++ b/Documentation/devicetree/bindings/sound/fsl,asrc.txt @@ -0,0 +1,60 @@ +Freescale Asynchronous Sample Rate Converter (ASRC) Controller + +The Asynchronous Sample Rate Converter (ASRC) converts the sampling rate of a +signal associated with an input clock into a signal associated with a different +output clock. The driver currently works as a Front End of DPCM with other Back +Ends Audio controller such as ESAI, SSI and SAI. It has three pairs to support +three substreams within totally 10 channels. + +Required properties: + + - compatible : Contains "fsl,imx35-asrc" or "fsl,imx53-asrc". + + - reg : Offset and length of the register set for the device. + + - interrupts : Contains the spdif interrupt. + + - dmas : Generic dma devicetree binding as described in + Documentation/devicetree/bindings/dma/dma.txt. + + - dma-names : Contains "rxa", "rxb", "rxc", "txa", "txb" and "txc". + + - clocks : Contains an entry for each entry in clock-names. + + - clock-names : Contains the following entries + "mem" Peripheral access clock to access registers. + "ipg" Peripheral clock to driver module. + "asrck_<0-f>" Clock sources for input and output clock. + + - big-endian : If this property is absent, the little endian mode + will be in use as default. Otherwise, the big endian + mode will be in use for all the device registers. + + - fsl,asrc-rate : Defines a mutual sample rate used by DPCM Back Ends. + + - fsl,asrc-width : Defines a mutual sample width used by DPCM Back Ends. + +Example: + +asrc: asrc@02034000 { + compatible = "fsl,imx53-asrc"; + reg = <0x02034000 0x4000>; + interrupts = <0 50 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks 107>, <&clks 107>, <&clks 0>, + <&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>, + <&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>, + <&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>, + <&clks 107>, <&clks 0>, <&clks 0>; + clock-names = "mem", "ipg", "asrck0", + "asrck_1", "asrck_2", "asrck_3", "asrck_4", + "asrck_5", "asrck_6", "asrck_7", "asrck_8", + "asrck_9", "asrck_a", "asrck_b", "asrck_c", + "asrck_d", "asrck_e", "asrck_f"; + dmas = <&sdma 17 23 1>, <&sdma 18 23 1>, <&sdma 19 23 1>, + <&sdma 20 23 1>, <&sdma 21 23 1>, <&sdma 22 23 1>; + dma-names = "rxa", "rxb", "rxc", + "txa", "txb", "txc"; + fsl,asrc-rate = <48000>; + fsl,asrc-width = <16>; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/sound/max98090.txt b/Documentation/devicetree/bindings/sound/max98090.txt index a5e63fa47dc5..c454e67f54bb 100644 --- a/Documentation/devicetree/bindings/sound/max98090.txt +++ b/Documentation/devicetree/bindings/sound/max98090.txt @@ -4,7 +4,7 @@ This device supports I2C only. Required properties: -- compatible : "maxim,max98090". +- compatible : "maxim,max98090" or "maxim,max98091". - reg : The I2C address of the device. diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index 8346cab046cd..aa697abf337e 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -13,6 +13,9 @@ Required properties: - rcar_sound,src : Should contain SRC feature. The number of SRC subnode should be same as HW. see below for detail. +- rcar_sound,dvc : Should contain DVC feature. + The number of DVC subnode should be same as HW. + see below for detail. - rcar_sound,dai : DAI contents. The number of DAI subnode should be same as HW. see below for detail. @@ -21,6 +24,7 @@ SSI subnode properties: - interrupts : Should contain SSI interrupt for PIO transfer - shared-pin : if shared clock pin - pio-transfer : use PIO transfer mode +- no-busif : BUSIF is not ussed when [mem -> SSI] via DMA case SRC subnode properties: no properties at this point @@ -39,6 +43,11 @@ rcar_sound: rcar_sound@0xffd90000 { <0 0xec540000 0 0x1000>, /* SSIU */ <0 0xec541000 0 0x1280>; /* SSI */ + rcar_sound,dvc { + dvc0: dvc@0 { }; + dvc1: dvc@1 { }; + }; + rcar_sound,src { src0: src@0 { }; src1: src@1 { }; diff --git a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt new file mode 100644 index 000000000000..6c55fcfe5e1d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt @@ -0,0 +1,37 @@ +* Rockchip I2S controller + +The I2S bus (Inter-IC sound bus) is a serial link for digital +audio data transfer between devices in the system. + +Required properties: + +- compatible: should be one of the followings + - "rockchip,rk3066-i2s": for rk3066 + - "rockchip,rk3188-i2s", "rockchip,rk3066-i2s": for rk3188 + - "rockchip,rk3288-i2s", "rockchip,rk3066-i2s": for rk3288 +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: should contain the I2S interrupt. +- #address-cells: should be 1. +- #size-cells: should be 0. +- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, + Documentation/devicetree/bindings/dma/dma.txt +- dma-names: should include "tx" and "rx". +- clocks: a list of phandle + clock-specifer pairs, one for each entry in clock-names. +- clock-names: should contain followings: + - "i2s_hclk": clock for I2S BUS + - "i2s_clk" : clock for I2S controller + +Example for rk3288 I2S controller: + +i2s@ff890000 { + compatible = "rockchip,rk3288-i2s", "rockchip,rk3066-i2s"; + reg = <0xff890000 0x10000>; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&pdma1 0>, <&pdma1 1>; + dma-names = "rx", "tx"; + clock-names = "i2s_hclk", "i2s_clk"; + clocks = <&cru HCLK_I2S0>, <&cru SCLK_I2S0>; +}; |