1 files changed, 0 insertions, 103 deletions
diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt b/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt
deleted file mode 100644
index 5c090771c016..000000000000
--- a/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt
+++ /dev/null
@@ -1,103 +0,0 @@
-Qualcomm Universal Peripheral (QUP) Serial Peripheral Interface (SPI)
-
-The QUP core is an AHB slave that provides a common data path (an output FIFO
-and an input FIFO) for serial peripheral interface (SPI) mini-core.
-
-SPI in master mode supports up to 50MHz, up to four chip selects, programmable
-data path from 4 bits to 32 bits and numerous protocol variants.
-
-Required properties:
-- compatible:     Should contain:
-		  "qcom,spi-qup-v1.1.1" for 8660, 8960 and 8064.
-		  "qcom,spi-qup-v2.1.1" for 8974 and later
-		  "qcom,spi-qup-v2.2.1" for 8974 v2 and later.
-
-- reg:            Should contain base register location and length
-- interrupts:     Interrupt number used by this controller
-
-- clocks:         Should contain the core clock and the AHB clock.
-- clock-names:    Should be "core" for the core clock and "iface" for the
-                  AHB clock.
-
-- #address-cells: Number of cells required to define a chip select
-                  address on the SPI bus. Should be set to 1.
-- #size-cells:    Should be zero.
-
-Optional properties:
-- spi-max-frequency: Specifies maximum SPI clock frequency,
-                     Units - Hz. Definition as per
-                     Documentation/devicetree/bindings/spi/spi-bus.txt
-- num-cs:	total number of chipselects
-- cs-gpios:	should specify GPIOs used for chipselects.
-		The gpios will be referred to as reg = <index> in the SPI child
-		nodes.  If unspecified, a single SPI device without a chip
-		select can be used.
-
-- dmas:         Two DMA channel specifiers following the convention outlined
-                in bindings/dma/dma.txt
-- dma-names:    Names for the dma channels, if present. There must be at
-                least one channel named "tx" for transmit and named "rx" for
-                receive.
-
-SPI slave nodes must be children of the SPI master node and can contain
-properties described in Documentation/devicetree/bindings/spi/spi-bus.txt
-
-Example:
-
-	spi_8: spi@f9964000 { /* BLSP2 QUP2 */
-
-		compatible = "qcom,spi-qup-v2";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0xf9964000 0x1000>;
-		interrupts = <0 102 0>;
-		spi-max-frequency = <19200000>;
-
-		clocks = <&gcc GCC_BLSP2_QUP2_SPI_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
-		clock-names = "core", "iface";
-
-		dmas = <&blsp1_bam 13>, <&blsp1_bam 12>;
-		dma-names = "rx", "tx";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&spi8_default>;
-
-		device@0 {
-			compatible = "arm,pl022-dummy";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			reg = <0>; /* Chip select 0 */
-			spi-max-frequency = <19200000>;
-			spi-cpol;
-		};
-
-		device@1 {
-			compatible = "arm,pl022-dummy";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			reg = <1>; /* Chip select 1 */
-			spi-max-frequency = <9600000>;
-			spi-cpha;
-		};
-
-		device@2 {
-			compatible = "arm,pl022-dummy";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			reg = <2>; /* Chip select 2 */
-			spi-max-frequency = <19200000>;
-			spi-cpol;
-			spi-cpha;
-		};
-
-		device@3 {
-			compatible = "arm,pl022-dummy";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			reg = <3>; /* Chip select 3 */
-			spi-max-frequency = <19200000>;
-			spi-cpol;
-			spi-cpha;
-			spi-cs-high;
-		};
-	};