diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
260 files changed, 5490 insertions, 1336 deletions
diff --git a/Documentation/devicetree/bindings/Makefile b/Documentation/devicetree/bindings/Makefile index 6e5cef0ed6fb..50daa0b3b032 100644 --- a/Documentation/devicetree/bindings/Makefile +++ b/Documentation/devicetree/bindings/Makefile @@ -17,7 +17,11 @@ extra-y += $(DT_TMP_SCHEMA) quiet_cmd_mk_schema = SCHEMA $@ cmd_mk_schema = $(DT_MK_SCHEMA) $(DT_MK_SCHEMA_FLAGS) -o $@ $(filter-out FORCE, $^) -DT_DOCS = $(shell cd $(srctree)/$(src) && find * -name '*.yaml') +DT_DOCS = $(shell \ + cd $(srctree)/$(src) && \ + find * \( -name '*.yaml' ! -name $(DT_TMP_SCHEMA) \) \ + ) + DT_SCHEMA_FILES ?= $(addprefix $(src)/,$(DT_DOCS)) extra-y += $(patsubst $(src)/%.yaml,%.example.dts, $(DT_SCHEMA_FILES)) diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt index 8dbc259081e4..7f40cb5f490b 100644 --- a/Documentation/devicetree/bindings/arm/amlogic.txt +++ b/Documentation/devicetree/bindings/arm/amlogic.txt @@ -109,6 +109,7 @@ Board compatible values (alphabetically, grouped by SoC): - "amlogic,s400" (Meson axg a113d) - "amlogic,u200" (Meson g12a s905d2) + - "amediatech,x96-max" (Meson g12a s905x2) Amlogic Meson Firmware registers Interface ------------------------------------------ diff --git a/Documentation/devicetree/bindings/arm/armadeus.txt b/Documentation/devicetree/bindings/arm/armadeus.txt deleted file mode 100644 index 9821283ff516..000000000000 --- a/Documentation/devicetree/bindings/arm/armadeus.txt +++ /dev/null @@ -1,6 +0,0 @@ -Armadeus i.MX Platforms Device Tree Bindings ------------------------------------------------ - -APF51: i.MX51 based module. -Required root node properties: - - compatible = "armadeus,imx51-apf51", "fsl,imx51"; diff --git a/Documentation/devicetree/bindings/arm/atmel-sysregs.txt b/Documentation/devicetree/bindings/arm/atmel-sysregs.txt index 14f319f694b7..e61d00e25b95 100644 --- a/Documentation/devicetree/bindings/arm/atmel-sysregs.txt +++ b/Documentation/devicetree/bindings/arm/atmel-sysregs.txt @@ -21,7 +21,8 @@ Its subnodes can be: RSTC Reset Controller required properties: - compatible: Should be "atmel,<chip>-rstc". - <chip> can be "at91sam9260" or "at91sam9g45" or "sama5d3" + <chip> can be "at91sam9260", "at91sam9g45", "sama5d3" or "samx7" + it also can be "microchip,sam9x60-rstc" - reg: Should contain registers location and length - clocks: phandle to input clock. @@ -147,6 +148,7 @@ required properties: - compatible: Should be "atmel,<chip>-sfr", "syscon" or "atmel,<chip>-sfrbu", "syscon" <chip> can be "sama5d3", "sama5d4" or "sama5d2". + It also can be "microchip,sam9x60-sfr", "syscon". - reg: Should contain registers location and length sfr@f0038000 { diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt index 0dcc3ea5adff..245328f36580 100644 --- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt @@ -30,6 +30,10 @@ Raspberry Pi 2 Model B Required root node properties: compatible = "raspberrypi,2-model-b", "brcm,bcm2836"; +Raspberry Pi 3 Model A+ +Required root node properties: +compatible = "raspberrypi,3-model-a-plus", "brcm,bcm2837"; + Raspberry Pi 3 Model B Required root node properties: compatible = "raspberrypi,3-model-b", "brcm,bcm2837"; diff --git a/Documentation/devicetree/bindings/arm/bhf.txt b/Documentation/devicetree/bindings/arm/bhf.txt deleted file mode 100644 index 886b503caf9c..000000000000 --- a/Documentation/devicetree/bindings/arm/bhf.txt +++ /dev/null @@ -1,6 +0,0 @@ -Beckhoff Automation Platforms Device Tree Bindings --------------------------------------------------- - -CX9020 Embedded PC -Required root node properties: - - compatible = "bhf,cx9020", "fsl,imx53"; diff --git a/Documentation/devicetree/bindings/arm/bitmain.yaml b/Documentation/devicetree/bindings/arm/bitmain.yaml new file mode 100644 index 000000000000..0efdb4ac028e --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bitmain.yaml @@ -0,0 +1,18 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/bitmain.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Bitmain platform device tree bindings + +maintainers: + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + +properties: + compatible: + items: + - enum: + - bitmain,sophon-edge + - const: bitmain,bm1880 +... diff --git a/Documentation/devicetree/bindings/arm/compulab-boards.txt b/Documentation/devicetree/bindings/arm/compulab-boards.txt deleted file mode 100644 index 42a10285af9c..000000000000 --- a/Documentation/devicetree/bindings/arm/compulab-boards.txt +++ /dev/null @@ -1,25 +0,0 @@ -CompuLab SB-SOM is a multi-module baseboard capable of carrying: - - CM-T43 - - CM-T54 - - CM-QS600 - - CL-SOM-AM57x - - CL-SOM-iMX7 -modules with minor modifications to the SB-SOM assembly. - -Required root node properties: - - compatible = should be "compulab,sb-som" - -Compulab CL-SOM-iMX7 is a miniature System-on-Module (SoM) based on -Freescale i.MX7 ARM Cortex-A7 System-on-Chip. - -Required root node properties: - - compatible = "compulab,cl-som-imx7", "fsl,imx7d"; - -Compulab SBC-iMX7 is a single board computer based on the -Freescale i.MX7 system-on-chip. SBC-iMX7 is implemented with -the CL-SOM-iMX7 System-on-Module providing most of the functions, -and SB-SOM-iMX7 carrier board providing additional peripheral -functions and connectors. - -Required root node properties: - - compatible = "compulab,sbc-imx7", "compulab,cl-som-imx7", "fsl,imx7d"; diff --git a/Documentation/devicetree/bindings/arm/cpu-capacity.txt b/Documentation/devicetree/bindings/arm/cpu-capacity.txt index 84262cdb8d29..96fa46cb133c 100644 --- a/Documentation/devicetree/bindings/arm/cpu-capacity.txt +++ b/Documentation/devicetree/bindings/arm/cpu-capacity.txt @@ -235,4 +235,4 @@ cpus { =========================================== [1] ARM Linux Kernel documentation - CPUs bindings - Documentation/devicetree/bindings/arm/cpus.txt + Documentation/devicetree/bindings/arm/cpus.yaml diff --git a/Documentation/devicetree/bindings/arm/cpus.yaml b/Documentation/devicetree/bindings/arm/cpus.yaml index 298c17b327c6..365dcf384d73 100644 --- a/Documentation/devicetree/bindings/arm/cpus.yaml +++ b/Documentation/devicetree/bindings/arm/cpus.yaml @@ -228,6 +228,7 @@ patternProperties: - renesas,r9a06g032-smp - rockchip,rk3036-smp - rockchip,rk3066-smp + - socionext,milbeaut-m10v-smp - ste,dbx500-smp cpu-release-addr: diff --git a/Documentation/devicetree/bindings/arm/freescale/fsl,imx7ulp-sim.txt b/Documentation/devicetree/bindings/arm/freescale/fsl,imx7ulp-sim.txt new file mode 100644 index 000000000000..7d0c7f002401 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/freescale/fsl,imx7ulp-sim.txt @@ -0,0 +1,16 @@ +Freescale i.MX7ULP System Integration Module +---------------------------------------------- +The system integration module (SIM) provides system control and chip configuration +registers. In this module, chip revision information is located in JTAG ID register, +and a set of registers have been made available in DGO domain for SW use, with the +objective to maintain its value between system resets. + +Required properties: +- compatible: Should be "fsl,imx7ulp-sim". +- reg: Specifies base physical address and size of the register sets. + +Example: +sim: sim@410a3000 { + compatible = "fsl,imx7ulp-sim", "syscon"; + reg = <0x410a3000 0x1000>; +}; diff --git a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt index 27784b6edfed..72d481c8dd48 100644 --- a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt +++ b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt @@ -58,7 +58,11 @@ This binding for the SCU power domain providers uses the generic power domain binding[2]. Required properties: -- compatible: Should be "fsl,imx8qxp-scu-pd". +- compatible: Should be one of: + "fsl,imx8qm-scu-pd", + "fsl,imx8qxp-scu-pd" + followed by "fsl,scu-pd" + - #power-domain-cells: Must be 1. Contains the Resource ID used by SCU commands. See detailed Resource ID list from: @@ -70,7 +74,10 @@ Clock bindings based on SCU Message Protocol This binding uses the common clock binding[1]. Required properties: -- compatible: Should be "fsl,imx8qxp-clock". +- compatible: Should be one of: + "fsl,imx8qm-clock" + "fsl,imx8qxp-clock" + followed by "fsl,scu-clk" - #clock-cells: Should be 1. Contains the Clock ID value. - clocks: List of clock specifiers, must contain an entry for each required entry in clock-names @@ -137,7 +144,7 @@ firmware { &lsio_mu1 1 3>; clk: clk { - compatible = "fsl,imx8qxp-clk"; + compatible = "fsl,imx8qxp-clk", "fsl,scu-clk"; #clock-cells = <1>; }; @@ -154,7 +161,7 @@ firmware { }; pd: imx8qx-pd { - compatible = "fsl,imx8qxp-scu-pd"; + compatible = "fsl,imx8qxp-scu-pd", "fsl,scu-pd"; #power-domain-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt deleted file mode 100644 index 7fbc42484001..000000000000 --- a/Documentation/devicetree/bindings/arm/fsl.txt +++ /dev/null @@ -1,237 +0,0 @@ -Freescale i.MX Platforms Device Tree Bindings ------------------------------------------------ - -i.MX23 Evaluation Kit -Required root node properties: - - compatible = "fsl,imx23-evk", "fsl,imx23"; - -i.MX25 Product Development Kit -Required root node properties: - - compatible = "fsl,imx25-pdk", "fsl,imx25"; - -i.MX27 Product Development Kit -Required root node properties: - - compatible = "fsl,imx27-pdk", "fsl,imx27"; - -i.MX28 Evaluation Kit -Required root node properties: - - compatible = "fsl,imx28-evk", "fsl,imx28"; - -i.MX51 Babbage Board -Required root node properties: - - compatible = "fsl,imx51-babbage", "fsl,imx51"; - -i.MX53 Automotive Reference Design Board -Required root node properties: - - compatible = "fsl,imx53-ard", "fsl,imx53"; - -i.MX53 Evaluation Kit -Required root node properties: - - compatible = "fsl,imx53-evk", "fsl,imx53"; - -i.MX53 Quick Start Board -Required root node properties: - - compatible = "fsl,imx53-qsb", "fsl,imx53"; - -i.MX53 Smart Mobile Reference Design Board -Required root node properties: - - compatible = "fsl,imx53-smd", "fsl,imx53"; - -i.MX6 Quad Armadillo2 Board -Required root node properties: - - compatible = "fsl,imx6q-arm2", "fsl,imx6q"; - -i.MX6 Quad SABRE Lite Board -Required root node properties: - - compatible = "fsl,imx6q-sabrelite", "fsl,imx6q"; - -i.MX6 Quad SABRE Smart Device Board -Required root node properties: - - compatible = "fsl,imx6q-sabresd", "fsl,imx6q"; - -i.MX6 Quad SABRE Automotive Board -Required root node properties: - - compatible = "fsl,imx6q-sabreauto", "fsl,imx6q"; - -i.MX6SLL EVK board -Required root node properties: - - compatible = "fsl,imx6sll-evk", "fsl,imx6sll"; - -i.MX6 Quad Plus SABRE Smart Device Board -Required root node properties: - - compatible = "fsl,imx6qp-sabresd", "fsl,imx6qp"; - -i.MX6 Quad Plus SABRE Automotive Board -Required root node properties: - - compatible = "fsl,imx6qp-sabreauto", "fsl,imx6qp"; - -i.MX6 DualLite SABRE Smart Device Board -Required root node properties: - - compatible = "fsl,imx6dl-sabresd", "fsl,imx6dl"; - -i.MX6 DualLite/Solo SABRE Automotive Board -Required root node properties: - - compatible = "fsl,imx6dl-sabreauto", "fsl,imx6dl"; - -i.MX6 SoloLite EVK Board -Required root node properties: - - compatible = "fsl,imx6sl-evk", "fsl,imx6sl"; - -i.MX6 UltraLite 14x14 EVK Board -Required root node properties: - - compatible = "fsl,imx6ul-14x14-evk", "fsl,imx6ul"; - -i.MX6 UltraLiteLite 14x14 EVK Board -Required root node properties: - - compatible = "fsl,imx6ull-14x14-evk", "fsl,imx6ull"; - -i.MX6 ULZ 14x14 EVK Board -Required root node properties: - - compatible = "fsl,imx6ulz-14x14-evk", "fsl,imx6ull", "fsl,imx6ulz"; - -i.MX6 SoloX SDB Board -Required root node properties: - - compatible = "fsl,imx6sx-sdb", "fsl,imx6sx"; - -i.MX6 SoloX Sabre Auto Board -Required root node properties: - - compatible = "fsl,imx6sx-sabreauto", "fsl,imx6sx"; - -i.MX7 SabreSD Board -Required root node properties: - - compatible = "fsl,imx7d-sdb", "fsl,imx7d"; - -i.MX7ULP Evaluation Kit -Required root node properties: - - compatible = "fsl,imx7ulp-evk", "fsl,imx7ulp"; - -Generic i.MX boards -------------------- - -No iomux setup is done for these boards, so this must have been configured -by the bootloader for boards to work with the generic bindings. - -i.MX27 generic board -Required root node properties: - - compatible = "fsl,imx27"; - -i.MX51 generic board -Required root node properties: - - compatible = "fsl,imx51"; - -i.MX53 generic board -Required root node properties: - - compatible = "fsl,imx53"; - -i.MX6q generic board -Required root node properties: - - compatible = "fsl,imx6q"; - -i.MX7ULP generic board -Required root node properties: - - compatible = "fsl,imx7ulp"; - -Freescale Vybrid Platform Device Tree Bindings ----------------------------------------------- - -For the Vybrid SoC familiy all variants with DDR controller are supported, -which is the VF5xx and VF6xx series. Out of historical reasons, in most -places the kernel uses vf610 to refer to the whole familiy. -The compatible string "fsl,vf610m4" is used for the secondary Cortex-M4 -core support. - -Required root node compatible property (one of them): - - compatible = "fsl,vf500"; - - compatible = "fsl,vf510"; - - compatible = "fsl,vf600"; - - compatible = "fsl,vf610"; - - compatible = "fsl,vf610m4"; - -Freescale LS1021A Platform Device Tree Bindings ------------------------------------------------- - -Required root node compatible properties: - - compatible = "fsl,ls1021a"; - -Freescale ARMv8 based Layerscape SoC family Device Tree Bindings ----------------------------------------------------------------- - -LS1012A SoC -Required root node properties: - - compatible = "fsl,ls1012a"; - -LS1012A ARMv8 based RDB Board -Required root node properties: - - compatible = "fsl,ls1012a-rdb", "fsl,ls1012a"; - -LS1012A ARMv8 based FRDM Board -Required root node properties: - - compatible = "fsl,ls1012a-frdm", "fsl,ls1012a"; - -LS1012A ARMv8 based QDS Board -Required root node properties: - - compatible = "fsl,ls1012a-qds", "fsl,ls1012a"; - -LS1043A SoC -Required root node properties: - - compatible = "fsl,ls1043a"; - -LS1043A ARMv8 based RDB Board -Required root node properties: - - compatible = "fsl,ls1043a-rdb", "fsl,ls1043a"; - -LS1043A ARMv8 based QDS Board -Required root node properties: - - compatible = "fsl,ls1043a-qds", "fsl,ls1043a"; - -LS1046A SoC -Required root node properties: - - compatible = "fsl,ls1046a"; - -LS1046A ARMv8 based QDS Board -Required root node properties: - - compatible = "fsl,ls1046a-qds", "fsl,ls1046a"; - -LS1046A ARMv8 based RDB Board -Required root node properties: - - compatible = "fsl,ls1046a-rdb", "fsl,ls1046a"; - -LS1088A SoC -Required root node properties: - - compatible = "fsl,ls1088a"; - -LS1088A ARMv8 based QDS Board -Required root node properties: - - compatible = "fsl,ls1088a-qds", "fsl,ls1088a"; - -LS1088A ARMv8 based RDB Board -Required root node properties: - - compatible = "fsl,ls1088a-rdb", "fsl,ls1088a"; - -LS2080A SoC -Required root node properties: - - compatible = "fsl,ls2080a"; - -LS2080A ARMv8 based Simulator model -Required root node properties: - - compatible = "fsl,ls2080a-simu", "fsl,ls2080a"; - -LS2080A ARMv8 based QDS Board -Required root node properties: - - compatible = "fsl,ls2080a-qds", "fsl,ls2080a"; - -LS2080A ARMv8 based RDB Board -Required root node properties: - - compatible = "fsl,ls2080a-rdb", "fsl,ls2080a"; - -LS2088A SoC -Required root node properties: - - compatible = "fsl,ls2088a"; - -LS2088A ARMv8 based QDS Board -Required root node properties: - - compatible = "fsl,ls2088a-qds", "fsl,ls2088a"; - -LS2088A ARMv8 based RDB Board -Required root node properties: - - compatible = "fsl,ls2088a-rdb", "fsl,ls2088a"; diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml new file mode 100644 index 000000000000..7e2cd6ad26bd --- /dev/null +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -0,0 +1,232 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/bindings/arm/fsl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale i.MX Platforms Device Tree Bindings + +maintainers: + - Shawn Guo <shawnguo@kernel.org> + - Li Yang <leoyang.li@nxp.com> + +properties: + $nodename: + const: '/' + compatible: + oneOf: + - description: i.MX23 based Boards + items: + - enum: + - fsl,imx23-evk + - olimex,imx23-olinuxino + - const: fsl,imx23 + + - description: i.MX25 Product Development Kit + items: + - enum: + - fsl,imx25-pdk + - const: fsl,imx25 + + - description: i.MX27 Product Development Kit + items: + - enum: + - fsl,imx27-pdk + - const: fsl,imx27 + + - description: i.MX28 based Boards + items: + - enum: + - fsl,imx28-evk + - i2se,duckbill + - i2se,duckbill-2 + - technologic,imx28-ts4600 + - const: fsl,imx28 + - description: i.MX28 Duckbill 2 based Boards + items: + - enum: + - i2se,duckbill-2-485 + - i2se,duckbill-2-enocean + - i2se,duckbill-2-spi + - const: i2se,duckbill-2 + - const: fsl,imx28 + + - description: i.MX51 Babbage Board + items: + - enum: + - armadeus,imx51-apf51 + - fsl,imx51-babbage + - technologic,imx51-ts4800 + - const: fsl,imx51 + + - description: i.MX53 based Boards + items: + - enum: + - bhf,cx9020 + - fsl,imx53-ard + - fsl,imx53-evk + - fsl,imx53-qsb + - fsl,imx53-smd + - const: fsl,imx53 + + - description: i.MX6Q based Boards + items: + - enum: + - fsl,imx6q-arm2 + - fsl,imx6q-sabreauto + - fsl,imx6q-sabrelite + - fsl,imx6q-sabresd + - technologic,imx6q-ts4900 + - technologic,imx6q-ts7970 + - const: fsl,imx6q + + - description: i.MX6QP based Boards + items: + - enum: + - fsl,imx6qp-sabreauto # i.MX6 Quad Plus SABRE Automotive Board + - fsl,imx6qp-sabresd # i.MX6 Quad Plus SABRE Smart Device Board + - const: fsl,imx6qp + + - description: i.MX6DL based Boards + items: + - enum: + - fsl,imx6dl-sabreauto # i.MX6 DualLite/Solo SABRE Automotive Board + - fsl,imx6dl-sabresd # i.MX6 DualLite SABRE Smart Device Board + - technologic,imx6dl-ts4900 + - technologic,imx6dl-ts7970 + - ysoft,imx6dl-yapp4-draco # i.MX6 DualLite Y Soft IOTA Draco board + - ysoft,imx6dl-yapp4-hydra # i.MX6 DualLite Y Soft IOTA Hydra board + - ysoft,imx6dl-yapp4-ursa # i.MX6 Solo Y Soft IOTA Ursa board + - const: fsl,imx6dl + + - description: i.MX6SL based Boards + items: + - enum: + - fsl,imx6sl-evk # i.MX6 SoloLite EVK Board + - const: fsl,imx6sl + + - description: i.MX6SLL based Boards + items: + - enum: + - fsl,imx6sll-evk + - const: fsl,imx6sll + + - description: i.MX6SX based Boards + items: + - enum: + - fsl,imx6sx-sabreauto # i.MX6 SoloX Sabre Auto Board + - fsl,imx6sx-sdb # i.MX6 SoloX SDB Board + - const: fsl,imx6sx + + - description: i.MX6UL based Boards + items: + - enum: + - fsl,imx6ul-14x14-evk # i.MX6 UltraLite 14x14 EVK Board + - const: fsl,imx6ul + + - description: i.MX6ULL based Boards + items: + - enum: + - fsl,imx6ull-14x14-evk # i.MX6 UltraLiteLite 14x14 EVK Board + - const: fsl,imx6ull + + - description: i.MX6ULZ based Boards + items: + - enum: + - fsl,imx6ulz-14x14-evk # i.MX6 ULZ 14x14 EVK Board + - const: fsl,imx6ull # This seems odd. Should be last? + - const: fsl,imx6ulz + + - description: i.MX7D based Boards + items: + - enum: + - fsl,imx7d-sdb # i.MX7 SabreSD Board + - const: fsl,imx7d + + - description: + Compulab SBC-iMX7 is a single board computer based on the + Freescale i.MX7 system-on-chip. SBC-iMX7 is implemented with + the CL-SOM-iMX7 System-on-Module providing most of the functions, + and SB-SOM-iMX7 carrier board providing additional peripheral + functions and connectors. + items: + - const: compulab,sbc-imx7 + - const: compulab,cl-som-imx7 + - const: fsl,imx7d + + - description: i.MX8QXP based Boards + items: + - enum: + - fsl,imx8qxp-mek # i.MX8QXP MEK Board + - const: fsl,imx8qxp + + - description: + Freescale Vybrid Platform Device Tree Bindings + + For the Vybrid SoC familiy all variants with DDR controller are supported, + which is the VF5xx and VF6xx series. Out of historical reasons, in most + places the kernel uses vf610 to refer to the whole familiy. + The compatible string "fsl,vf610m4" is used for the secondary Cortex-M4 + core support. + items: + - enum: + - fsl,vf500 + - fsl,vf510 + - fsl,vf600 + - fsl,vf610 + - fsl,vf610m4 + + - description: LS1012A based Boards + items: + - enum: + - ebs-systart,oxalis + - fsl,ls1012a-rdb + - fsl,ls1012a-frdm + - fsl,ls1012a-qds + - const: fsl,ls1012a + + - description: LS1021A based Boards + items: + - enum: + - fsl,ls1021a-moxa-uc-8410a + - fsl,ls1021a-qds + - fsl,ls1021a-twr + - const: fsl,ls1021a + + - description: LS1043A based Boards + items: + - enum: + - fsl,ls1043a-rdb + - fsl,ls1043a-qds + - const: fsl,ls1043a + + - description: LS1046A based Boards + items: + - enum: + - fsl,ls1046a-qds + - fsl,ls1046a-rdb + - const: fsl,ls1046a + + - description: LS1088A based Boards + items: + - enum: + - fsl,ls1088a-qds + - fsl,ls1088a-rdb + - const: fsl,ls1088a + + - description: LS2080A based Boards + items: + - enum: + - fsl,ls2080a-simu + - fsl,ls2080a-qds + - fsl,ls2080a-rdb + - const: fsl,ls2080a + + - description: LS2088A based Boards + items: + - enum: + - fsl,ls2088a-qds + - fsl,ls2088a-rdb + - const: fsl,ls2088a + +... diff --git a/Documentation/devicetree/bindings/arm/i2se.txt b/Documentation/devicetree/bindings/arm/i2se.txt deleted file mode 100644 index dbd54a3aa07d..000000000000 --- a/Documentation/devicetree/bindings/arm/i2se.txt +++ /dev/null @@ -1,22 +0,0 @@ -I2SE Device Tree Bindings -------------------------- - -Duckbill Board -Required root node properties: - - compatible = "i2se,duckbill", "fsl,imx28"; - -Duckbill 2 Board -Required root node properties: - - compatible = "i2se,duckbill-2", "fsl,imx28"; - -Duckbill 2 485 Board -Required root node properties: - - compatible = "i2se,duckbill-2-485", "i2se,duckbill-2", "fsl,imx28"; - -Duckbill 2 EnOcean Board -Required root node properties: - - compatible = "i2se,duckbill-2-enocean", "i2se,duckbill-2", "fsl,imx28"; - -Duckbill 2 SPI Board -Required root node properties: - - compatible = "i2se,duckbill-2-spi", "i2se,duckbill-2", "fsl,imx28"; diff --git a/Documentation/devicetree/bindings/arm/idle-states.txt b/Documentation/devicetree/bindings/arm/idle-states.txt index 8f0937db55c5..45730ba60af5 100644 --- a/Documentation/devicetree/bindings/arm/idle-states.txt +++ b/Documentation/devicetree/bindings/arm/idle-states.txt @@ -684,7 +684,7 @@ cpus { =========================================== [1] ARM Linux Kernel documentation - CPUs bindings - Documentation/devicetree/bindings/arm/cpus.txt + Documentation/devicetree/bindings/arm/cpus.yaml [2] ARM Linux Kernel documentation - PSCI bindings Documentation/devicetree/bindings/arm/psci.txt diff --git a/Documentation/devicetree/bindings/arm/mediatek.txt b/Documentation/devicetree/bindings/arm/mediatek.txt index 8f260e5cfd16..56ac7896d6d8 100644 --- a/Documentation/devicetree/bindings/arm/mediatek.txt +++ b/Documentation/devicetree/bindings/arm/mediatek.txt @@ -15,11 +15,12 @@ compatible: Must contain one of "mediatek,mt6795" "mediatek,mt6797" "mediatek,mt7622" - "mediatek,mt7623" which is referred to MT7623N SoC - "mediatek,mt7623a" + "mediatek,mt7623" + "mediatek,mt7629" "mediatek,mt8127" "mediatek,mt8135" "mediatek,mt8173" + "mediatek,mt8183" Supported boards: @@ -57,6 +58,9 @@ Supported boards: - Reference board variant 1 for MT7622: Required root node properties: - compatible = "mediatek,mt7622-rfb1", "mediatek,mt7622"; +- Bananapi BPI-R64 for MT7622: + Required root node properties: + - compatible = "bananapi,bpi-r64", "mediatek,mt7622"; - Reference board for MT7623a with eMMC: Required root node properties: - compatible = "mediatek,mt7623a-rfb-emmc", "mediatek,mt7623"; @@ -68,6 +72,9 @@ Supported boards: - compatible = "mediatek,mt7623n-rfb-emmc", "mediatek,mt7623"; - Bananapi BPI-R2 board: - compatible = "bananapi,bpi-r2", "mediatek,mt7623"; +- Reference board for MT7629: + Required root node properties: + - compatible = "mediatek,mt7629-rfb", "mediatek,mt7629"; - MTK mt8127 tablet moose EVB: Required root node properties: - compatible = "mediatek,mt8127-moose", "mediatek,mt8127"; @@ -77,3 +84,6 @@ Supported boards: - MTK mt8173 tablet EVB: Required root node properties: - compatible = "mediatek,mt8173-evb", "mediatek,mt8173"; +- Evaluation board for MT8183: + Required root node properties: + - compatible = "mediatek,mt8183-evb", "mediatek,mt8183"; diff --git a/Documentation/devicetree/bindings/arm/olimex.txt b/Documentation/devicetree/bindings/arm/olimex.txt deleted file mode 100644 index d726aeca56be..000000000000 --- a/Documentation/devicetree/bindings/arm/olimex.txt +++ /dev/null @@ -1,10 +0,0 @@ -Olimex Device Tree Bindings ---------------------------- - -SAM9-L9260 Board -Required root node properties: - - compatible = "olimex,sam9-l9260", "atmel,at91sam9260"; - -i.MX23 Olinuxino Low Cost Board -Required root node properties: - - compatible = "olimex,imx23-olinuxino", "fsl,imx23"; diff --git a/Documentation/devicetree/bindings/arm/pmu.txt b/Documentation/devicetree/bindings/arm/pmu.txt deleted file mode 100644 index 13611a8199bb..000000000000 --- a/Documentation/devicetree/bindings/arm/pmu.txt +++ /dev/null @@ -1,70 +0,0 @@ -* ARM Performance Monitor Units - -ARM cores often have a PMU for counting cpu and cache events like cache misses -and hits. The interface to the PMU is part of the ARM ARM. The ARM PMU -representation in the device tree should be done as under:- - -Required properties: - -- compatible : should be one of - "apm,potenza-pmu" - "arm,armv8-pmuv3" - "arm,cortex-a73-pmu" - "arm,cortex-a72-pmu" - "arm,cortex-a57-pmu" - "arm,cortex-a53-pmu" - "arm,cortex-a35-pmu" - "arm,cortex-a17-pmu" - "arm,cortex-a15-pmu" - "arm,cortex-a12-pmu" - "arm,cortex-a9-pmu" - "arm,cortex-a8-pmu" - "arm,cortex-a7-pmu" - "arm,cortex-a5-pmu" - "arm,arm11mpcore-pmu" - "arm,arm1176-pmu" - "arm,arm1136-pmu" - "brcm,vulcan-pmu" - "cavium,thunder-pmu" - "qcom,scorpion-pmu" - "qcom,scorpion-mp-pmu" - "qcom,krait-pmu" -- interrupts : 1 combined interrupt or 1 per core. If the interrupt is a per-cpu - interrupt (PPI) then 1 interrupt should be specified. - -Optional properties: - -- interrupt-affinity : When using SPIs, specifies a list of phandles to CPU - nodes corresponding directly to the affinity of - the SPIs listed in the interrupts property. - - When using a PPI, specifies a list of phandles to CPU - nodes corresponding to the set of CPUs which have - a PMU of this type signalling the PPI listed in the - interrupts property, unless this is already specified - by the PPI interrupt specifier itself (in which case - the interrupt-affinity property shouldn't be present). - - This property should be present when there is more than - a single SPI. - - -- qcom,no-pc-write : Indicates that this PMU doesn't support the 0xc and 0xd - events. - -- secure-reg-access : Indicates that the ARMv7 Secure Debug Enable Register - (SDER) is accessible. This will cause the driver to do - any setup required that is only possible in ARMv7 secure - state. If not present the ARMv7 SDER will not be touched, - which means the PMU may fail to operate unless external - code (bootloader or security monitor) has performed the - appropriate initialisation. Note that this property is - not valid for non-ARMv7 CPUs or ARMv7 CPUs booting Linux - in Non-secure state. - -Example: - -pmu { - compatible = "arm,cortex-a9-pmu"; - interrupts = <100 101>; -}; diff --git a/Documentation/devicetree/bindings/arm/pmu.yaml b/Documentation/devicetree/bindings/arm/pmu.yaml new file mode 100644 index 000000000000..52ae094ce330 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/pmu.yaml @@ -0,0 +1,87 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/pmu.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM Performance Monitor Units + +maintainers: + - Mark Rutland <mark.rutland@arm.com> + - Will Deacon <will.deacon@arm.com> + +description: |+ + ARM cores often have a PMU for counting cpu and cache events like cache misses + and hits. The interface to the PMU is part of the ARM ARM. The ARM PMU + representation in the device tree should be done as under:- + +properties: + compatible: + items: + - enum: + - apm,potenza-pmu + - arm,armv8-pmuv3 + - arm,cortex-a73-pmu + - arm,cortex-a72-pmu + - arm,cortex-a57-pmu + - arm,cortex-a53-pmu + - arm,cortex-a35-pmu + - arm,cortex-a17-pmu + - arm,cortex-a15-pmu + - arm,cortex-a12-pmu + - arm,cortex-a9-pmu + - arm,cortex-a8-pmu + - arm,cortex-a7-pmu + - arm,cortex-a5-pmu + - arm,arm11mpcore-pmu + - arm,arm1176-pmu + - arm,arm1136-pmu + - brcm,vulcan-pmu + - cavium,thunder-pmu + - qcom,scorpion-pmu + - qcom,scorpion-mp-pmu + - qcom,krait-pmu + + interrupts: + # Don't know how many CPUs, so no constraints to specify + description: 1 per-cpu interrupt (PPI) or 1 interrupt per core. + + interrupt-affinity: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + When using SPIs, specifies a list of phandles to CPU + nodes corresponding directly to the affinity of + the SPIs listed in the interrupts property. + + When using a PPI, specifies a list of phandles to CPU + nodes corresponding to the set of CPUs which have + a PMU of this type signalling the PPI listed in the + interrupts property, unless this is already specified + by the PPI interrupt specifier itself (in which case + the interrupt-affinity property shouldn't be present). + + This property should be present when there is more than + a single SPI. + + qcom,no-pc-write: + type: boolean + description: + Indicates that this PMU doesn't support the 0xc and 0xd events. + + secure-reg-access: + type: boolean + description: + Indicates that the ARMv7 Secure Debug Enable Register + (SDER) is accessible. This will cause the driver to do + any setup required that is only possible in ARMv7 secure + state. If not present the ARMv7 SDER will not be touched, + which means the PMU may fail to operate unless external + code (bootloader or security monitor) has performed the + appropriate initialisation. Note that this property is + not valid for non-ARMv7 CPUs or ARMv7 CPUs booting Linux + in Non-secure state. + +required: + - compatible + +... diff --git a/Documentation/devicetree/bindings/arm/renesas.yaml b/Documentation/devicetree/bindings/arm/renesas.yaml new file mode 100644 index 000000000000..19f379863d50 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/renesas.yaml @@ -0,0 +1,238 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/shmobile.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas SH-Mobile, R-Mobile, and R-Car Platform Device Tree Bindings + +maintainers: + - Geert Uytterhoeven <geert+renesas@glider.be> + +properties: + $nodename: + const: '/' + compatible: + oneOf: + - description: Emma Mobile EV2 + items: + - enum: + - renesas,kzm9d # Kyoto Microcomputer Co. KZM-A9-Dual + - const: renesas,emev2 + + - description: RZ/A1H (R7S72100) + items: + - enum: + - renesas,genmai # Genmai (RTK772100BC00000BR) + - renesas,gr-peach # GR-Peach (X28A-M01-E/F) + - renesas,rskrza1 # RSKRZA1 (YR0K77210C000BE) + - const: renesas,r7s72100 + + - description: RZ/A2 (R7S9210) + items: + - enum: + - renesas,rza2mevb # RZ/A2M Eval Board (RTK7921053S00000BE) + - const: renesas,r7s9210 + + - description: SH-Mobile AG5 (R8A73A00/SH73A0) + items: + - enum: + - renesas,kzm9g # Kyoto Microcomputer Co. KZM-A9-GT + - const: renesas,sh73a0 + + - description: R-Mobile APE6 (R8A73A40) + items: + - enum: + - renesas,ape6evm + - const: renesas,r8a73a4 + + - description: R-Mobile A1 (R8A77400) + items: + - enum: + - renesas,armadillo800eva # Atmark Techno Armadillo-800 EVA + - const: renesas,r8a7740 + + - description: RZ/G1H (R8A77420) + items: + - const: renesas,r8a7742 + + - description: RZ/G1M (R8A77430) + items: + - enum: + # iWave Systems RZ/G1M Qseven Development Platform (iW-RainboW-G20D-Qseven) + - iwave,g20d + - const: iwave,g20m + - const: renesas,r8a7743 + + - items: + - enum: + # iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven) + - iwave,g20m + - renesas,sk-rzg1m # SK-RZG1M (YR8A77430S000BE) + - const: renesas,r8a7743 + + - description: RZ/G1N (R8A77440) + items: + - enum: + # iWave Systems RZ/G1N Qseven Development Platform (iW-RainboW-G20D-Qseven) + - iwave,g20d + - const: iwave,g20m + - const: renesas,r8a7744 + + - items: + - enum: + # iWave Systems RZ/G1N Qseven System On Module (iW-RainboW-G20M-Qseven) + - iwave,g20m + - const: renesas,r8a7744 + + - description: RZ/G1E (R8A77450) + items: + - enum: + - iwave,g22m # iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM) + - renesas,sk-rzg1e # SK-RZG1E (YR8A77450S000BE) + - const: renesas,r8a7745 + + - description: iWave Systems RZ/G1E SODIMM SOM Development Platform (iW-RainboW-G22D) + items: + - const: iwave,g22d + - const: iwave,g22m + - const: renesas,r8a7745 + + - description: RZ/G1C (R8A77470) + items: + - enum: + - iwave,g23s #iWave Systems RZ/G1C Single Board Computer (iW-RainboW-G23S) + - const: renesas,r8a77470 + + - description: RZ/G2M (R8A774A1) + items: + - const: renesas,r8a774a1 + + - description: RZ/G2E (R8A774C0) + items: + - enum: + - si-linux,cat874 # Silicon Linux RZ/G2E 96board platform (CAT874) + - const: renesas,r8a774c0 + + - items: + - enum: + - si-linux,cat875 # Silicon Linux sub board for CAT874 (CAT875) + - const: si-linux,cat874 + - const: renesas,r8a774c0 + + - description: R-Car M1A (R8A77781) + items: + - enum: + - renesas,bockw + - const: renesas,r8a7778 + + - description: R-Car H1 (R8A77790) + items: + - enum: + - renesas,marzen # Marzen (R0P7779A00010S) + - const: renesas,r8a7779 + + - description: R-Car H2 (R8A77900) + items: + - enum: + - renesas,lager # Lager (RTP0RC7790SEB00010S) + - renesas,stout # Stout (ADAS Starterkit, Y-R-CAR-ADAS-SKH2-BOARD) + - const: renesas,r8a7790 + + - description: R-Car M2-W (R8A77910) + items: + - enum: + - renesas,henninger + - renesas,koelsch # Koelsch (RTP0RC7791SEB00010S) + - renesas,porter # Porter (M2-LCDP) + - const: renesas,r8a7791 + + - description: R-Car V2H (R8A77920) + items: + - enum: + - renesas,blanche # Blanche (RTP0RC7792SEB00010S) + - renesas,wheat # Wheat (RTP0RC7792ASKB0000JE) + - const: renesas,r8a7792 + + - description: R-Car M2-N (R8A77930) + items: + - enum: + - renesas,gose # Gose (RTP0RC7793SEB00010S) + - const: renesas,r8a7793 + + - description: R-Car E2 (R8A77940) + items: + - enum: + - renesas,alt # Alt (RTP0RC7794SEB00010S) + - renesas,silk # SILK (RTP0RC7794LCB00011S) + - const: renesas,r8a7794 + + - description: R-Car H3 (R8A77950) + items: + - enum: + # H3ULCB (R-Car Starter Kit Premier, RTP0RC7795SKBX0010SA00 (H3 ES1.1)) + # H3ULCB (R-Car Starter Kit Premier, RTP0RC77951SKBX010SA00 (H3 ES2.0)) + - renesas,h3ulcb + - renesas,salvator-x # Salvator-X (RTP0RC7795SIPB0010S) + - renesas,salvator-xs # Salvator-XS (Salvator-X 2nd version, RTP0RC7795SIPB0012S) + - const: renesas,r8a7795 + + - description: R-Car M3-W (R8A77960) + items: + - enum: + - renesas,m3ulcb # M3ULCB (R-Car Starter Kit Pro, RTP0RC7796SKBX0010SA09 (M3 ES1.0)) + - renesas,salvator-x # Salvator-X (RTP0RC7796SIPB0011S) + - renesas,salvator-xs # Salvator-XS (Salvator-X 2nd version, RTP0RC7796SIPB0012S) + - const: renesas,r8a7796 + + - description: Kingfisher (SBEV-RCAR-KF-M03) + items: + - const: shimafuji,kingfisher + - enum: + - renesas,h3ulcb + - renesas,m3ulcb + - enum: + - renesas,r8a7795 + - renesas,r8a7796 + + - description: R-Car M3-N (R8A77965) + items: + - enum: + - renesas,m3nulcb # M3NULCB (R-Car Starter Kit Pro, RTP0RC77965SKBX010SA00 (M3-N ES1.1)) + - renesas,salvator-x # Salvator-X (RTP0RC7796SIPB0011S (M3-N)) + - renesas,salvator-xs # Salvator-XS (Salvator-X 2nd version, RTP0RC77965SIPB012S) + - const: renesas,r8a77965 + + - description: R-Car V3M (R8A77970) + items: + - enum: + - renesas,eagle # Eagle (RTP0RC77970SEB0010S) + - renesas,v3msk # V3MSK (Y-ASK-RCAR-V3M-WS10) + - const: renesas,r8a77970 + + - description: R-Car V3H (R8A77980) + items: + - enum: + - renesas,condor # Condor (RTP0RC77980SEB0010SS/RTP0RC77980SEB0010SA01) + - renesas,v3hsk # V3HSK (Y-ASK-RCAR-V3H-WS10) + - const: renesas,r8a77980 + + - description: R-Car E3 (R8A77990) + items: + - enum: + - renesas,ebisu # Ebisu (RTP0RC77990SEB0010S) + - const: renesas,r8a77990 + + - description: R-Car D3 (R8A77995) + items: + - enum: + - renesas,draak # Draak (RTP0RC77995SEB0010S) + - const: renesas,r8a77995 + + - description: RZ/N1D (R9A06G032) + items: + - enum: + - renesas,rzn1d400-db # RZN1D-DB (RZ/N1D Demo Board for the RZ/N1D 400 pins package) + - const: renesas,r9a06g032 + +... diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml index b12958bda09c..061a03edf9c8 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.yaml +++ b/Documentation/devicetree/bindings/arm/rockchip.yaml @@ -60,6 +60,11 @@ properties: - const: chipspark,rayeager-px2 - const: rockchip,rk3066a + - description: Elgin RV1108 R1 + items: + - const: elgin,rv1108-r1 + - const: rockchip,rv1108 + - description: Firefly Firefly-RK3288 items: - enum: @@ -87,6 +92,13 @@ properties: - const: firefly,roc-rk3399-pc - const: rockchip,rk3399 + - description: FriendlyElec NanoPi4 series boards + items: + - enum: + - friendlyarm,nanopc-t4 + - friendlyarm,nanopi-m4 + - const: rockchip,rk3399 + - description: GeekBuying GeekBox items: - const: geekbuying,geekbox @@ -317,6 +329,11 @@ properties: - const: radxa,rock - const: rockchip,rk3188 + - description: Radxa ROCK Pi 4 + items: + - const: radxa,rockpi4 + - const: rockchip,rk3399 + - description: Radxa Rock2 Square items: - const: radxa,rock2-square diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt deleted file mode 100644 index 7f91c2a8b54e..000000000000 --- a/Documentation/devicetree/bindings/arm/shmobile.txt +++ /dev/null @@ -1,155 +0,0 @@ -Renesas SH-Mobile, R-Mobile, and R-Car Platform Device Tree Bindings --------------------------------------------------------------------- - -SoCs: - - - Emma Mobile EV2 - compatible = "renesas,emev2" - - RZ/A1H (R7S72100) - compatible = "renesas,r7s72100" - - RZ/A2 (R7S9210) - compatible = "renesas,r7s9210" - - SH-Mobile AG5 (R8A73A00/SH73A0) - compatible = "renesas,sh73a0" - - R-Mobile APE6 (R8A73A40) - compatible = "renesas,r8a73a4" - - R-Mobile A1 (R8A77400) - compatible = "renesas,r8a7740" - - RZ/G1H (R8A77420) - compatible = "renesas,r8a7742" - - RZ/G1M (R8A77430) - compatible = "renesas,r8a7743" - - RZ/G1N (R8A77440) - compatible = "renesas,r8a7744" - - RZ/G1E (R8A77450) - compatible = "renesas,r8a7745" - - RZ/G1C (R8A77470) - compatible = "renesas,r8a77470" - - RZ/G2M (R8A774A1) - compatible = "renesas,r8a774a1" - - RZ/G2E (R8A774C0) - compatible = "renesas,r8a774c0" - - R-Car M1A (R8A77781) - compatible = "renesas,r8a7778" - - R-Car H1 (R8A77790) - compatible = "renesas,r8a7779" - - R-Car H2 (R8A77900) - compatible = "renesas,r8a7790" - - R-Car M2-W (R8A77910) - compatible = "renesas,r8a7791" - - R-Car V2H (R8A77920) - compatible = "renesas,r8a7792" - - R-Car M2-N (R8A77930) - compatible = "renesas,r8a7793" - - R-Car E2 (R8A77940) - compatible = "renesas,r8a7794" - - R-Car H3 (R8A77950) - compatible = "renesas,r8a7795" - - R-Car M3-W (R8A77960) - compatible = "renesas,r8a7796" - - R-Car M3-N (R8A77965) - compatible = "renesas,r8a77965" - - R-Car V3M (R8A77970) - compatible = "renesas,r8a77970" - - R-Car V3H (R8A77980) - compatible = "renesas,r8a77980" - - R-Car E3 (R8A77990) - compatible = "renesas,r8a77990" - - R-Car D3 (R8A77995) - compatible = "renesas,r8a77995" - - RZ/N1D (R9A06G032) - compatible = "renesas,r9a06g032" - -Boards: - - - Alt (RTP0RC7794SEB00010S) - compatible = "renesas,alt", "renesas,r8a7794" - - APE6-EVM - compatible = "renesas,ape6evm", "renesas,r8a73a4" - - Atmark Techno Armadillo-800 EVA - compatible = "renesas,armadillo800eva", "renesas,r8a7740" - - Blanche (RTP0RC7792SEB00010S) - compatible = "renesas,blanche", "renesas,r8a7792" - - BOCK-W - compatible = "renesas,bockw", "renesas,r8a7778" - - Condor (RTP0RC77980SEB0010SS/RTP0RC77980SEB0010SA01) - compatible = "renesas,condor", "renesas,r8a77980" - - Draak (RTP0RC77995SEB0010S) - compatible = "renesas,draak", "renesas,r8a77995" - - Eagle (RTP0RC77970SEB0010S) - compatible = "renesas,eagle", "renesas,r8a77970" - - Ebisu (RTP0RC77990SEB0010S) - compatible = "renesas,ebisu", "renesas,r8a77990" - - Genmai (RTK772100BC00000BR) - compatible = "renesas,genmai", "renesas,r7s72100" - - GR-Peach (X28A-M01-E/F) - compatible = "renesas,gr-peach", "renesas,r7s72100" - - Gose (RTP0RC7793SEB00010S) - compatible = "renesas,gose", "renesas,r8a7793" - - H3ULCB (R-Car Starter Kit Premier, RTP0RC7795SKBX0010SA00 (H3 ES1.1)) - H3ULCB (R-Car Starter Kit Premier, RTP0RC77951SKBX010SA00 (H3 ES2.0)) - compatible = "renesas,h3ulcb", "renesas,r8a7795" - - Henninger - compatible = "renesas,henninger", "renesas,r8a7791" - - iWave Systems RZ/G1C Single Board Computer (iW-RainboW-G23S) - compatible = "iwave,g23s", "renesas,r8a77470" - - iWave Systems RZ/G1E SODIMM SOM Development Platform (iW-RainboW-G22D) - compatible = "iwave,g22d", "iwave,g22m", "renesas,r8a7745" - - iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM) - compatible = "iwave,g22m", "renesas,r8a7745" - - iWave Systems RZ/G1M Qseven Development Platform (iW-RainboW-G20D-Qseven) - compatible = "iwave,g20d", "iwave,g20m", "renesas,r8a7743" - - iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven) - compatible = "iwave,g20m", "renesas,r8a7743" - - iWave Systems RZ/G1N Qseven Development Platform (iW-RainboW-G20D-Qseven) - compatible = "iwave,g20d", "iwave,g20m", "renesas,r8a7744" - - iWave Systems RZ/G1N Qseven System On Module (iW-RainboW-G20M-Qseven) - compatible = "iwave,g20m", "renesas,r8a7744" - - Kingfisher (SBEV-RCAR-KF-M03) - compatible = "shimafuji,kingfisher" - - Koelsch (RTP0RC7791SEB00010S) - compatible = "renesas,koelsch", "renesas,r8a7791" - - Kyoto Microcomputer Co. KZM-A9-Dual - compatible = "renesas,kzm9d", "renesas,emev2" - - Kyoto Microcomputer Co. KZM-A9-GT - compatible = "renesas,kzm9g", "renesas,sh73a0" - - Lager (RTP0RC7790SEB00010S) - compatible = "renesas,lager", "renesas,r8a7790" - - M3ULCB (R-Car Starter Kit Pro, RTP0RC7796SKBX0010SA09 (M3 ES1.0)) - compatible = "renesas,m3ulcb", "renesas,r8a7796" - - M3NULCB (R-Car Starter Kit Pro, RTP0RC77965SKBX010SA00 (M3-N ES1.1)) - compatible = "renesas,m3nulcb", "renesas,r8a77965" - - Marzen (R0P7779A00010S) - compatible = "renesas,marzen", "renesas,r8a7779" - - Porter (M2-LCDP) - compatible = "renesas,porter", "renesas,r8a7791" - - RSKRZA1 (YR0K77210C000BE) - compatible = "renesas,rskrza1", "renesas,r7s72100" - - RZN1D-DB (RZ/N1D Demo Board for the RZ/N1D 400 pins package) - compatible = "renesas,rzn1d400-db", "renesas,r9a06g032" - - Salvator-X (RTP0RC7795SIPB0010S) - compatible = "renesas,salvator-x", "renesas,r8a7795" - - Salvator-X (RTP0RC7796SIPB0011S) - compatible = "renesas,salvator-x", "renesas,r8a7796" - - Salvator-X (RTP0RC7796SIPB0011S (M3-N)) - compatible = "renesas,salvator-x", "renesas,r8a77965" - - Salvator-XS (Salvator-X 2nd version, RTP0RC7795SIPB0012S) - compatible = "renesas,salvator-xs", "renesas,r8a7795" - - Salvator-XS (Salvator-X 2nd version, RTP0RC7796SIPB0012S) - compatible = "renesas,salvator-xs", "renesas,r8a7796" - - Salvator-XS (Salvator-X 2nd version, RTP0RC77965SIPB012S) - compatible = "renesas,salvator-xs", "renesas,r8a77965" - - SILK (RTP0RC7794LCB00011S) - compatible = "renesas,silk", "renesas,r8a7794" - - SK-RZG1E (YR8A77450S000BE) - compatible = "renesas,sk-rzg1e", "renesas,r8a7745" - - SK-RZG1M (YR8A77430S000BE) - compatible = "renesas,sk-rzg1m", "renesas,r8a7743" - - Stout (ADAS Starterkit, Y-R-CAR-ADAS-SKH2-BOARD) - compatible = "renesas,stout", "renesas,r8a7790" - - V3HSK (Y-ASK-RCAR-V3H-WS10) - compatible = "renesas,v3hsk", "renesas,r8a77980" - - V3MSK (Y-ASK-RCAR-V3M-WS10) - compatible = "renesas,v3msk", "renesas,r8a77970" - - Wheat (RTP0RC7792ASKB0000JE) - compatible = "renesas,wheat", "renesas,r8a7792" diff --git a/Documentation/devicetree/bindings/arm/socionext/milbeaut.yaml b/Documentation/devicetree/bindings/arm/socionext/milbeaut.yaml new file mode 100644 index 000000000000..aae53fc3cb1e --- /dev/null +++ b/Documentation/devicetree/bindings/arm/socionext/milbeaut.yaml @@ -0,0 +1,22 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/milbeaut.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Milbeaut platforms device tree bindings + +maintainers: + - Taichi Sugaya <sugaya.taichi@socionext.com> + - Takao Orito <orito.takao@socionext.com> + +properties: + $nodename: + const: '/' + compatible: + oneOf: + - items: + - enum: + - socionext,milbeaut-m10v-evb + - const: socionext,sc2000a +... diff --git a/Documentation/devicetree/bindings/arm/sp810.txt b/Documentation/devicetree/bindings/arm/sp810.txt index 1b2ab1ff5587..46652bf65147 100644 --- a/Documentation/devicetree/bindings/arm/sp810.txt +++ b/Documentation/devicetree/bindings/arm/sp810.txt @@ -4,7 +4,7 @@ SP810 System Controller Required properties: - compatible: standard compatible string for a Primecell peripheral, - see Documentation/devicetree/bindings/arm/primecell.txt + see Documentation/devicetree/bindings/arm/primecell.yaml for more details should be: "arm,sp810", "arm,primecell" diff --git a/Documentation/devicetree/bindings/arm/technologic.txt b/Documentation/devicetree/bindings/arm/technologic.txt deleted file mode 100644 index f1cedc00dcab..000000000000 --- a/Documentation/devicetree/bindings/arm/technologic.txt +++ /dev/null @@ -1,23 +0,0 @@ -Technologic Systems Platforms Device Tree Bindings --------------------------------------------------- - -TS-4600 is a System-on-Module based on the Freescale i.MX28 System-on-Chip. -It can be mounted on a carrier board providing additional peripheral connectors. -Required root node properties: - - compatible = "technologic,imx28-ts4600", "fsl,imx28" - -TS-4800 board -Required root node properties: - - compatible = "technologic,imx51-ts4800", "fsl,imx51"; - -TS-4900 is a System-on-Module based on the Freescale i.MX6 System-on-Chip. -It can be mounted on a carrier board providing additional peripheral connectors. -Required root node properties: - - compatible = "technologic,imx6dl-ts4900", "fsl,imx6dl" - - compatible = "technologic,imx6q-ts4900", "fsl,imx6q" - -TS-7970 is a System-on-Module based on the Freescale i.MX6 System-on-Chip. -It can be mounted on a carrier board providing additional peripheral connectors. -Required root node properties: - - compatible = "technologic,imx6dl-ts7970", "fsl,imx6dl" - - compatible = "technologic,imx6q-ts7970", "fsl,imx6q" diff --git a/Documentation/devicetree/bindings/arm/tegra.yaml b/Documentation/devicetree/bindings/arm/tegra.yaml index fbcde8a7e067..60b38eb5c61a 100644 --- a/Documentation/devicetree/bindings/arm/tegra.yaml +++ b/Documentation/devicetree/bindings/arm/tegra.yaml @@ -87,9 +87,11 @@ properties: - const: nvidia,tegra124 - items: - enum: + - nvidia,darcy - nvidia,p2371-0000 - nvidia,p2371-2180 - nvidia,p2571 + - nvidia,p2894-0050-a08 - const: nvidia,tegra210 - items: - enum: diff --git a/Documentation/devicetree/bindings/arm/topology.txt b/Documentation/devicetree/bindings/arm/topology.txt index de9eb0486630..b0d80c0fb265 100644 --- a/Documentation/devicetree/bindings/arm/topology.txt +++ b/Documentation/devicetree/bindings/arm/topology.txt @@ -472,4 +472,4 @@ cpus { =============================================================================== [1] ARM Linux kernel documentation - Documentation/devicetree/bindings/arm/cpus.txt + Documentation/devicetree/bindings/arm/cpus.yaml diff --git a/Documentation/devicetree/bindings/bus/imx-weim.txt b/Documentation/devicetree/bindings/bus/imx-weim.txt index 683eaf3aed79..dda7d6d66479 100644 --- a/Documentation/devicetree/bindings/bus/imx-weim.txt +++ b/Documentation/devicetree/bindings/bus/imx-weim.txt @@ -47,9 +47,9 @@ Optional properties: Timing property for child nodes. It is mandatory, not optional. - fsl,weim-cs-timing: The timing array, contains timing values for the - child node. We can get the CS index from the child - node's "reg" property. The number of registers depends - on the selected chip. + child node. We get the CS indexes from the address + ranges in the child node's "reg" property. + The number of registers depends on the selected chip: For i.MX1, i.MX21 ("fsl,imx1-weim") there are two registers: CSxU, CSxL. For i.MX25, i.MX27, i.MX31 and i.MX35 ("fsl,imx27-weim") @@ -80,3 +80,29 @@ Example for an imx6q-sabreauto board, the NOR flash connected to the WEIM: 0x0000c000 0x1404a38e 0x00000000>; }; }; + +Example for an imx6q-based board, a multi-chipselect device connected to WEIM: + +In this case, both chip select 0 and 1 will be configured with the same timing +array values. + + weim: weim@21b8000 { + compatible = "fsl,imx6q-weim"; + reg = <0x021b8000 0x4000>; + clocks = <&clks 196>; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x08000000 0x02000000 + 1 0 0x0a000000 0x02000000 + 2 0 0x0c000000 0x02000000 + 3 0 0x0e000000 0x02000000>; + fsl,weim-cs-gpr = <&gpr>; + + acme@0 { + compatible = "acme,whatever"; + reg = <0 0 0x100>, <0 0x400000 0x800>, + <1 0x400000 0x800>; + fsl,weim-cs-timing = <0x024400b1 0x00001010 0x20081100 + 0x00000000 0xa0000240 0x00000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/marvell,mmp2.txt b/Documentation/devicetree/bindings/clock/marvell,mmp2.txt index af376a01f2b7..23b52dc02266 100644 --- a/Documentation/devicetree/bindings/clock/marvell,mmp2.txt +++ b/Documentation/devicetree/bindings/clock/marvell,mmp2.txt @@ -18,4 +18,4 @@ Required Properties: Each clock is assigned an identifier and client nodes use this identifier to specify the clock which they consume. -All these identifier could be found in <dt-bindings/clock/marvell-mmp2.h>. +All these identifiers could be found in <dt-bindings/clock/marvell,mmp2.h>. diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt index dff236f524a7..958e0ad78c52 100644 --- a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt @@ -8,10 +8,11 @@ the fast CPU cluster. It consists of a free-running voltage controlled oscillator connected to the CPU voltage rail (VDD_CPU), and a closed loop control module that will automatically adjust the VDD_CPU voltage by communicating with an off-chip PMIC either via an I2C bus or via PWM signals. -Currently only the I2C mode is supported by these bindings. Required properties: -- compatible : should be "nvidia,tegra124-dfll" +- compatible : should be one of: + - "nvidia,tegra124-dfll": for Tegra124 + - "nvidia,tegra210-dfll": for Tegra210 - reg : Defines the following set of registers, in the order listed: - registers for the DFLL control logic. - registers for the I2C output logic. @@ -45,10 +46,31 @@ Required properties for the control loop parameters: Optional properties for the control loop parameters: - nvidia,cg-scale: Boolean value, see the field DFLL_PARAMS_CG_SCALE in the TRM. +Optional properties for mode selection: +- nvidia,pwm-to-pmic: Use PWM to control regulator rather then I2C. + Required properties for I2C mode: - nvidia,i2c-fs-rate: I2C transfer rate, if using full speed mode. -Example: +Required properties for PWM mode: +- nvidia,pwm-period-nanoseconds: period of PWM square wave in nanoseconds. +- nvidia,pwm-tristate-microvolts: Regulator voltage in micro volts when PWM + control is disabled and the PWM output is tristated. Note that this voltage is + configured in hardware, typically via a resistor divider. +- nvidia,pwm-min-microvolts: Regulator voltage in micro volts when PWM control + is enabled and PWM output is low. Hence, this is the minimum output voltage + that the regulator supports when PWM control is enabled. +- nvidia,pwm-voltage-step-microvolts: Voltage increase in micro volts + corresponding to a 1/33th increase in duty cycle. Eg the voltage for 2/33th + duty cycle would be: nvidia,pwm-min-microvolts + + nvidia,pwm-voltage-step-microvolts * 2. +- pinctrl-0: I/O pad configuration when PWM control is enabled. +- pinctrl-1: I/O pad configuration when PWM control is disabled. +- pinctrl-names: must include the following entries: + - dvfs_pwm_enable: I/O pad configuration when PWM control is enabled. + - dvfs_pwm_disable: I/O pad configuration when PWM control is disabled. + +Example for I2C: clock@70110000 { compatible = "nvidia,tegra124-dfll"; @@ -76,3 +98,58 @@ clock@70110000 { nvidia,i2c-fs-rate = <400000>; }; + +Example for PWM: + +clock@70110000 { + compatible = "nvidia,tegra124-dfll"; + reg = <0 0x70110000 0 0x100>, /* DFLL control */ + <0 0x70110000 0 0x100>, /* I2C output control */ + <0 0x70110100 0 0x100>, /* Integrated I2C controller */ + <0 0x70110200 0 0x100>; /* Look-up table RAM */ + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA210_CLK_DFLL_SOC>, + <&tegra_car TEGRA210_CLK_DFLL_REF>, + <&tegra_car TEGRA124_CLK_I2C5>;; + clock-names = "soc", "ref", "i2c"; + resets = <&tegra_car TEGRA124_RST_DFLL_DVCO>; + reset-names = "dvco"; + #clock-cells = <0>; + clock-output-names = "dfllCPU_out"; + + nvidia,sample-rate = <25000>; + nvidia,droop-ctrl = <0x00000f00>; + nvidia,force-mode = <1>; + nvidia,cf = <6>; + nvidia,ci = <0>; + nvidia,cg = <2>; + + nvidia,pwm-min-microvolts = <708000>; /* 708mV */ + nvidia,pwm-period-nanoseconds = <2500>; /* 2.5us */ + nvidia,pwm-to-pmic; + nvidia,pwm-tristate-microvolts = <1000000>; + nvidia,pwm-voltage-step-microvolts = <19200>; /* 19.2mV */ + + pinctrl-names = "dvfs_pwm_enable", "dvfs_pwm_disable"; + pinctrl-0 = <&dvfs_pwm_active_state>; + pinctrl-1 = <&dvfs_pwm_inactive_state>; +}; + +/* pinmux nodes added for completeness. Binding doc can be found in: + * Documentation/devicetree/bindings/pinctrl/nvidia,tegra210-pinmux.txt + */ + +pinmux: pinmux@700008d4 { + dvfs_pwm_active_state: dvfs_pwm_active { + dvfs_pwm_pbb1 { + nvidia,pins = "dvfs_pwm_pbb1"; + nvidia,tristate = <TEGRA_PIN_DISABLE>; + }; + }; + dvfs_pwm_inactive_state: dvfs_pwm_inactive { + dvfs_pwm_pbb1 { + nvidia,pins = "dvfs_pwm_pbb1"; + nvidia,tristate = <TEGRA_PIN_ENABLE>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/cpufreq/nvidia,tegra124-cpufreq.txt b/Documentation/devicetree/bindings/cpufreq/nvidia,tegra124-cpufreq.txt index b1669fbfb740..03196d5ea515 100644 --- a/Documentation/devicetree/bindings/cpufreq/nvidia,tegra124-cpufreq.txt +++ b/Documentation/devicetree/bindings/cpufreq/nvidia,tegra124-cpufreq.txt @@ -9,11 +9,9 @@ Required properties: See ../clocks/clock-bindings.txt for details. - clock-names: Must include the following entries: - cpu_g: Clock mux for the fast CPU cluster. - - cpu_lp: Clock mux for the low-power CPU cluster. - pll_x: Fast PLL clocksource. - pll_p: Auxiliary PLL used during fast PLL rate changes. - dfll: Fast DFLL clocksource that also automatically scales CPU voltage. -- vdd-cpu-supply: Regulator for CPU voltage Optional properties: - clock-latency: Specify the possible maximum transition latency for clock, @@ -31,13 +29,11 @@ cpus { reg = <0>; clocks = <&tegra_car TEGRA124_CLK_CCLK_G>, - <&tegra_car TEGRA124_CLK_CCLK_LP>, <&tegra_car TEGRA124_CLK_PLL_X>, <&tegra_car TEGRA124_CLK_PLL_P>, <&dfll>; - clock-names = "cpu_g", "cpu_lp", "pll_x", "pll_p", "dfll"; + clock-names = "cpu_g", "pll_x", "pll_p", "dfll"; clock-latency = <300000>; - vdd-cpu-supply: <&vdd_cpu>; }; <...> diff --git a/Documentation/devicetree/bindings/crypto/samsung-slimsss.txt b/Documentation/devicetree/bindings/crypto/samsung-slimsss.txt new file mode 100644 index 000000000000..7ec9a5a7727a --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/samsung-slimsss.txt @@ -0,0 +1,19 @@ +Samsung SoC SlimSSS (Slim Security SubSystem) module + +The SlimSSS module in Exynos5433 SoC supports the following: +-- Feeder (FeedCtrl) +-- Advanced Encryption Standard (AES) with ECB,CBC,CTR,XTS and (CBC/XTS)/CTS +-- SHA-1/SHA-256 and (SHA-1/SHA-256)/HMAC + +Required properties: + +- compatible : Should contain entry for slimSSS version: + - "samsung,exynos5433-slim-sss" for Exynos5433 SoC. +- reg : Offset and length of the register set for the module +- interrupts : interrupt specifiers of SlimSSS module interrupts (one feed + control interrupt). + +- clocks : list of clock phandle and specifier pairs for all clocks listed in + clock-names property. +- clock-names : list of device clock input names; should contain "pclk" and + "aclk" for slim-sss in Exynos5433. diff --git a/Documentation/devicetree/bindings/display/amlogic,simple-framebuffer.txt b/Documentation/devicetree/bindings/display/amlogic,simple-framebuffer.txt new file mode 100644 index 000000000000..aaa6c24c8e70 --- /dev/null +++ b/Documentation/devicetree/bindings/display/amlogic,simple-framebuffer.txt @@ -0,0 +1,33 @@ +Meson specific Simple Framebuffer bindings + +This binding documents meson specific extensions to the simple-framebuffer +bindings. The meson simplefb u-boot code relies on the devicetree containing +pre-populated simplefb nodes. + +These extensions are intended so that u-boot can select the right node based +on which pipeline is being used. As such they are solely intended for +firmware / bootloader use, and the OS should ignore them. + +Required properties: +- compatible: "amlogic,simple-framebuffer", "simple-framebuffer" +- amlogic,pipeline, one of: + "vpu-cvbs" + "vpu-hdmi" + +Example: + +chosen { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + simplefb_hdmi: framebuffer-hdmi { + compatible = "amlogic,simple-framebuffer", + "simple-framebuffer"; + amlogic,pipeline = "vpu-hdmi"; + clocks = <&clkc CLKID_HDMI_PCLK>, + <&clkc CLKID_CLK81>, + <&clkc CLKID_GCLK_VENCI_INT0>; + power-domains = <&pwrc_vpu>; + }; +}; diff --git a/Documentation/devicetree/bindings/display/arm,komeda.txt b/Documentation/devicetree/bindings/display/arm,komeda.txt new file mode 100644 index 000000000000..02b226532ebd --- /dev/null +++ b/Documentation/devicetree/bindings/display/arm,komeda.txt @@ -0,0 +1,73 @@ +Device Tree bindings for Arm Komeda display driver + +Required properties: +- compatible: Should be "arm,mali-d71" +- reg: Physical base address and length of the registers in the system +- interrupts: the interrupt line number of the device in the system +- clocks: A list of phandle + clock-specifier pairs, one for each entry + in 'clock-names' +- clock-names: A list of clock names. It should contain: + - "mclk": for the main processor clock + - "pclk": for the APB interface clock +- #address-cells: Must be 1 +- #size-cells: Must be 0 + +Required properties for sub-node: pipeline@nq +Each device contains one or two pipeline sub-nodes (at least one), each +pipeline node should provide properties: +- reg: Zero-indexed identifier for the pipeline +- clocks: A list of phandle + clock-specifier pairs, one for each entry + in 'clock-names' +- clock-names: should contain: + - "pxclk": pixel clock + - "aclk": AXI interface clock + +- port: each pipeline connect to an encoder input port. The connection is + modeled using the OF graph bindings specified in + Documentation/devicetree/bindings/graph.txt + +Optional properties: + - memory-region: phandle to a node describing memory (see + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt) + to be used for the framebuffer; if not present, the framebuffer may + be located anywhere in memory. + +Example: +/ { + ... + + dp0: display@c00000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "arm,mali-d71"; + reg = <0xc00000 0x20000>; + interrupts = <0 168 4>; + clocks = <&dpu_mclk>, <&dpu_aclk>; + clock-names = "mclk", "pclk"; + + dp0_pipe0: pipeline@0 { + clocks = <&fpgaosc2>, <&dpu_aclk>; + clock-names = "pxclk", "aclk"; + reg = <0>; + + port { + dp0_pipe0_out: endpoint { + remote-endpoint = <&db_dvi0_in>; + }; + }; + }; + + dp0_pipe1: pipeline@1 { + clocks = <&fpgaosc2>, <&dpu_aclk>; + clock-names = "pxclk", "aclk"; + reg = <1>; + + port { + dp0_pipe1_out: endpoint { + remote-endpoint = <&db_dvi1_in>; + }; + }; + }; + }; + ... +}; diff --git a/Documentation/devicetree/bindings/display/arm,pl11x.txt b/Documentation/devicetree/bindings/display/arm,pl11x.txt index ef89ab46b2c9..572fa2773ec4 100644 --- a/Documentation/devicetree/bindings/display/arm,pl11x.txt +++ b/Documentation/devicetree/bindings/display/arm,pl11x.txt @@ -1,6 +1,6 @@ * ARM PrimeCell Color LCD Controller PL110/PL111 -See also Documentation/devicetree/bindings/arm/primecell.txt +See also Documentation/devicetree/bindings/arm/primecell.yaml Required properties: diff --git a/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt b/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt index f5725bb6c61c..525a4bfd8634 100644 --- a/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt +++ b/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt @@ -31,28 +31,7 @@ Required subnodes: - one subnode per DSI device connected on the DSI bus. Each DSI device should contain a reg property encoding its virtual channel. -Cadence DPHY -============ - -Cadence DPHY block. - -Required properties: -- compatible: should be set to "cdns,dphy". -- reg: physical base address and length of the DPHY registers. -- clocks: DPHY reference clocks. -- clock-names: must contain "psm" and "pll_ref". -- #phy-cells: must be set to 0. - - Example: - dphy0: dphy@fd0e0000{ - compatible = "cdns,dphy"; - reg = <0x0 0xfd0e0000 0x0 0x1000>; - clocks = <&psm_clk>, <&pll_ref_clk>; - clock-names = "psm", "pll_ref"; - #phy-cells = <0>; - }; - dsi0: dsi@fd0c0000 { compatible = "cdns,dsi"; reg = <0x0 0xfd0c0000 0x0 0x1000>; diff --git a/Documentation/devicetree/bindings/display/bridge/lvds-transmitter.txt b/Documentation/devicetree/bindings/display/bridge/lvds-transmitter.txt index 50220190c203..60091db5dfa5 100644 --- a/Documentation/devicetree/bindings/display/bridge/lvds-transmitter.txt +++ b/Documentation/devicetree/bindings/display/bridge/lvds-transmitter.txt @@ -22,13 +22,11 @@ among others. Required properties: -- compatible: Must be one or more of the following - - "ti,ds90c185" for the TI DS90C185 FPD-Link Serializer - - "lvds-encoder" for a generic LVDS encoder device +- compatible: Must be "lvds-encoder" - When compatible with the generic version, nodes must list the - device-specific version corresponding to the device first - followed by the generic version. + Any encoder compatible with this generic binding, but with additional + properties not listed here, must list a device specific compatible first + followed by this generic compatible. Required nodes: @@ -44,8 +42,6 @@ Example lvds-encoder { compatible = "lvds-encoder"; - #address-cells = <1>; - #size-cells = <0>; ports { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt b/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt index ba5469dd09f3..900a884ad9f5 100644 --- a/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt +++ b/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt @@ -8,6 +8,8 @@ Required properties: - compatible : Shall contain one of - "renesas,r8a7743-lvds" for R8A7743 (RZ/G1M) compatible LVDS encoders + - "renesas,r8a7744-lvds" for R8A7744 (RZ/G1N) compatible LVDS encoders + - "renesas,r8a774c0-lvds" for R8A774C0 (RZ/G2E) compatible LVDS encoders - "renesas,r8a7790-lvds" for R8A7790 (R-Car H2) compatible LVDS encoders - "renesas,r8a7791-lvds" for R8A7791 (R-Car M2-W) compatible LVDS encoders - "renesas,r8a7793-lvds" for R8A7793 (R-Car M2-N) compatible LVDS encoders @@ -25,7 +27,7 @@ Required properties: - clock-names: Name of the clocks. This property is model-dependent. - The functional clock, which mandatory for all models, shall be listed first, and shall be named "fck". - - On R8A77990 and R8A77995, the LVDS encoder can use the EXTAL or + - On R8A77990, R8A77995 and R8A774C0, the LVDS encoder can use the EXTAL or DU_DOTCLKINx clocks. Those clocks are optional. When supplied they must be named "extal" and "dclkin.x" respectively, with "x" being the DU_DOTCLKIN numerical index. diff --git a/Documentation/devicetree/bindings/display/bridge/thine,thc63lvdm83d.txt b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvdm83d.txt index 527e236e9a2a..fee3c88e1a17 100644 --- a/Documentation/devicetree/bindings/display/bridge/thine,thc63lvdm83d.txt +++ b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvdm83d.txt @@ -10,7 +10,7 @@ Required properties: Optional properties: -- pwdn-gpios: Power down control GPIO +- powerdown-gpios: Power down control GPIO (the /PWDN pin, active low). Required nodes: diff --git a/Documentation/devicetree/bindings/display/bridge/ti,ds90c185.txt b/Documentation/devicetree/bindings/display/bridge/ti,ds90c185.txt new file mode 100644 index 000000000000..e575f996959a --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/ti,ds90c185.txt @@ -0,0 +1,55 @@ +Texas Instruments FPD-Link (LVDS) Serializer +-------------------------------------------- + +The DS90C185 and DS90C187 are low-power serializers for portable +battery-powered applications that reduces the size of the RGB +interface between the host GPU and the display. + +Required properties: + +- compatible: Should be + "ti,ds90c185", "lvds-encoder" for the TI DS90C185 FPD-Link Serializer + "ti,ds90c187", "lvds-encoder" for the TI DS90C187 FPD-Link Serializer + +Optional properties: + +- powerdown-gpios: Power down control GPIO (the PDB pin, active-low) + +Required nodes: + +The devices have two video ports. Their connections are modeled using the OF +graph bindings specified in Documentation/devicetree/bindings/graph.txt. + +- Video port 0 for parallel input +- Video port 1 for LVDS output + + +Example +------- + +lvds-encoder { + compatible = "ti,ds90c185", "lvds-encoder"; + + powerdown-gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + lvds_enc_in: endpoint { + remote-endpoint = <&lcdc_out_rgb>; + }; + }; + + port@1 { + reg = <1>; + + lvds_enc_out: endpoint { + remote-endpoint = <&lvds_panel_in>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/msm/gmu.txt b/Documentation/devicetree/bindings/display/msm/gmu.txt new file mode 100644 index 000000000000..3439b38e60f2 --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/gmu.txt @@ -0,0 +1,59 @@ +Qualcomm adreno/snapdragon GMU (Graphics management unit) + +The GMU is a programmable power controller for the GPU. the CPU controls the +GMU which in turn handles power controls for the GPU. + +Required properties: +- compatible: "qcom,adreno-gmu-XYZ.W", "qcom,adreno-gmu" + for example: "qcom,adreno-gmu-630.2", "qcom,adreno-gmu" + Note that you need to list the less specific "qcom,adreno-gmu" + for generic matches and the more specific identifier to identify + the specific device. +- reg: Physical base address and length of the GMU registers. +- reg-names: Matching names for the register regions + * "gmu" + * "gmu_pdc" + * "gmu_pdc_seg" +- interrupts: The interrupt signals from the GMU. +- interrupt-names: Matching names for the interrupts + * "hfi" + * "gmu" +- clocks: phandles to the device clocks +- clock-names: Matching names for the clocks + * "gmu" + * "cxo" + * "axi" + * "mnoc" +- power-domains: should be <&clock_gpucc GPU_CX_GDSC> +- iommus: phandle to the adreno iommu +- operating-points-v2: phandle to the OPP operating points + +Example: + +/ { + ... + + gmu: gmu@506a000 { + compatible="qcom,adreno-gmu-630.2", "qcom,adreno-gmu"; + + reg = <0x506a000 0x30000>, + <0xb280000 0x10000>, + <0xb480000 0x10000>; + reg-names = "gmu", "gmu_pdc", "gmu_pdc_seq"; + + interrupts = <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hfi", "gmu"; + + clocks = <&gpucc GPU_CC_CX_GMU_CLK>, + <&gpucc GPU_CC_CXO_CLK>, + <&gcc GCC_DDRSS_GPU_AXI_CLK>, + <&gcc GCC_GPU_MEMNOC_GFX_CLK>; + clock-names = "gmu", "cxo", "axi", "memnoc"; + + power-domains = <&gpucc GPU_CX_GDSC>; + iommus = <&adreno_smmu 5>; + + operating-points-v2 = <&gmu_opp_table>; + }; +}; diff --git a/Documentation/devicetree/bindings/display/msm/gpu.txt b/Documentation/devicetree/bindings/display/msm/gpu.txt index ac8df3b871f9..aad1aef682f7 100644 --- a/Documentation/devicetree/bindings/display/msm/gpu.txt +++ b/Documentation/devicetree/bindings/display/msm/gpu.txt @@ -10,14 +10,23 @@ Required properties: If "amd,imageon" is used, there should be no top level msm device. - reg: Physical base address and length of the controller's registers. - interrupts: The interrupt signal from the gpu. -- clocks: device clocks +- clocks: device clocks (if applicable) See ../clocks/clock-bindings.txt for details. -- clock-names: the following clocks are required: +- clock-names: the following clocks are required by a3xx, a4xx and a5xx + cores: * "core" * "iface" * "mem_iface" + For GMU attached devices the GPU clocks are not used and are not required. The + following devices should not list clocks: + - qcom,adreno-630.2 +- iommus: optional phandle to an adreno iommu instance +- operating-points-v2: optional phandle to the OPP operating points +- qcom,gmu: For GMU attached devices a phandle to the GMU device that will + control the power for the GPU. Applicable targets: + - qcom,adreno-630.2 -Example: +Example 3xx/4xx/a5xx: / { ... @@ -27,7 +36,6 @@ Example: reg = <0x04300000 0x20000>; reg-names = "kgsl_3d0_reg_memory"; interrupts = <GIC_SPI 80 0>; - interrupt-names = "kgsl_3d0_irq"; clock-names = "core", "iface", @@ -38,3 +46,30 @@ Example: <&mmcc MMSS_IMEM_AHB_CLK>; }; }; + +Example a6xx (with GMU): + +/ { + ... + + gpu@5000000 { + compatible = "qcom,adreno-630.2", "qcom,adreno"; + #stream-id-cells = <16>; + + reg = <0x5000000 0x40000>, <0x509e000 0x10>; + reg-names = "kgsl_3d0_reg_memory", "cx_mem"; + + /* + * Look ma, no clocks! The GPU clocks and power are + * controlled entirely by the GMU + */ + + interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>; + + iommus = <&adreno_smmu 0>; + + operating-points-v2 = <&gpu_opp_table>; + + qcom,gmu = <&gmu>; + }; +}; diff --git a/Documentation/devicetree/bindings/display/panel/auo,g101evn010 b/Documentation/devicetree/bindings/display/panel/auo,g101evn010.txt index bc6a0c858e23..bc6a0c858e23 100644 --- a/Documentation/devicetree/bindings/display/panel/auo,g101evn010 +++ b/Documentation/devicetree/bindings/display/panel/auo,g101evn010.txt diff --git a/Documentation/devicetree/bindings/display/panel/innolux,ee101ia-01d.txt b/Documentation/devicetree/bindings/display/panel/innolux,ee101ia-01d.txt new file mode 100644 index 000000000000..e5ca4ccd55ed --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/innolux,ee101ia-01d.txt @@ -0,0 +1,7 @@ +Innolux Corporation 10.1" EE101IA-01D WXGA (1280x800) LVDS panel + +Required properties: +- compatible: should be "innolux,ee101ia-01d" + +This binding is compatible with the lvds-panel binding, which is specified +in panel-lvds.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/lemaker,bl035-rgb-002.txt b/Documentation/devicetree/bindings/display/panel/lemaker,bl035-rgb-002.txt new file mode 100644 index 000000000000..74ee7ea6b493 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/lemaker,bl035-rgb-002.txt @@ -0,0 +1,12 @@ +LeMaker BL035-RGB-002 3.5" QVGA TFT LCD panel + +Required properties: +- compatible: should be "lemaker,bl035-rgb-002" +- power-supply: as specified in the base binding + +Optional properties: +- backlight: as specified in the base binding +- enable-gpios: as specified in the base binding + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.txt b/Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.txt new file mode 100644 index 000000000000..1639fb17a9f0 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.txt @@ -0,0 +1,14 @@ +PDA 91-00156-A0 5.0" WVGA TFT LCD panel + +Required properties: +- compatible: should be "pda,91-00156-a0" +- power-supply: this panel requires a single power supply. A phandle to a +regulator needs to be specified here. Compatible with panel-common binding which +is specified in the panel-common.txt in this directory. +- backlight: this panel's backlight is controlled by an external backlight +controller. A phandle to this controller needs to be specified here. +Compatible with panel-common binding which is specified in the panel-common.txt +in this directory. + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/sitronix,st7701.txt b/Documentation/devicetree/bindings/display/panel/sitronix,st7701.txt new file mode 100644 index 000000000000..ccd17597f1f6 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sitronix,st7701.txt @@ -0,0 +1,30 @@ +Sitronix ST7701 based LCD panels + +ST7701 designed for small and medium sizes of TFT LCD display, is +capable of supporting up to 480RGBX864 in resolution. It provides +several system interfaces like MIPI/RGB/SPI. + +Techstar TS8550B is 480x854, 2-lane MIPI DSI LCD panel which has +inbuilt ST7701 chip. + +Required properties: +- compatible: must be "sitronix,st7701" and one of + * "techstar,ts8550b" +- reset-gpios: a GPIO phandle for the reset pin + +Required properties for techstar,ts8550b: +- reg: DSI virtual channel used by that screen +- VCC-supply: analog regulator for MIPI circuit +- IOVCC-supply: I/O system regulator + +Optional properties: +- backlight: phandle for the backlight control. + +panel@0 { + compatible = "techstar,ts8550b", "sitronix,st7701"; + reg = <0>; + VCC-supply = <®_dldo2>; + IOVCC-supply = <®_dldo2>; + reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* LCD-RST: PD24 */ + backlight = <&backlight>; +}; diff --git a/Documentation/devicetree/bindings/display/renesas,du.txt b/Documentation/devicetree/bindings/display/renesas,du.txt index 3c855d9f2719..aedb22b4d161 100644 --- a/Documentation/devicetree/bindings/display/renesas,du.txt +++ b/Documentation/devicetree/bindings/display/renesas,du.txt @@ -7,6 +7,7 @@ Required Properties: - "renesas,du-r8a7744" for R8A7744 (RZ/G1N) compatible DU - "renesas,du-r8a7745" for R8A7745 (RZ/G1E) compatible DU - "renesas,du-r8a77470" for R8A77470 (RZ/G1C) compatible DU + - "renesas,du-r8a774c0" for R8A774C0 (RZ/G2E) compatible DU - "renesas,du-r8a7779" for R8A7779 (R-Car H1) compatible DU - "renesas,du-r8a7790" for R8A7790 (R-Car H2) compatible DU - "renesas,du-r8a7791" for R8A7791 (R-Car M2-W) compatible DU @@ -57,6 +58,7 @@ corresponding to each DU output. R8A7744 (RZ/G1N) DPAD 0 LVDS 0 - - R8A7745 (RZ/G1E) DPAD 0 DPAD 1 - - R8A77470 (RZ/G1C) DPAD 0 DPAD 1 LVDS 0 - + R8A774C0 (RZ/G2E) DPAD 0 LVDS 0 LVDS 1 - R8A7779 (R-Car H1) DPAD 0 DPAD 1 - - R8A7790 (R-Car H2) DPAD 0 LVDS 0 LVDS 1 - R8A7791 (R-Car M2-W) DPAD 0 LVDS 0 - - diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt b/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt index b79e5769f0ae..4f58c5a2d195 100644 --- a/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt +++ b/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt @@ -10,6 +10,7 @@ Required properties: "rockchip,rk3126-vop"; "rockchip,px30-vop-lit"; "rockchip,px30-vop-big"; + "rockchip,rk3066-vop"; "rockchip,rk3188-vop"; "rockchip,rk3288-vop"; "rockchip,rk3368-vop"; diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt index f426bdb42f18..31ab72cba3d4 100644 --- a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt @@ -156,6 +156,7 @@ Required properties: * allwinner,sun6i-a31-tcon * allwinner,sun6i-a31s-tcon * allwinner,sun7i-a20-tcon + * allwinner,sun8i-a23-tcon * allwinner,sun8i-a33-tcon * allwinner,sun8i-a83t-tcon-lcd * allwinner,sun8i-a83t-tcon-tv @@ -276,6 +277,7 @@ Required properties: - compatible: value must be one of: * allwinner,sun6i-a31-drc * allwinner,sun6i-a31s-drc + * allwinner,sun8i-a23-drc * allwinner,sun8i-a33-drc * allwinner,sun9i-a80-drc - reg: base address and size of the memory-mapped region. @@ -303,6 +305,7 @@ Required properties: * allwinner,sun5i-a13-display-backend * allwinner,sun6i-a31-display-backend * allwinner,sun7i-a20-display-backend + * allwinner,sun8i-a23-display-backend * allwinner,sun8i-a33-display-backend * allwinner,sun9i-a80-display-backend - reg: base address and size of the memory-mapped region. @@ -360,6 +363,7 @@ Required properties: * allwinner,sun5i-a13-display-frontend * allwinner,sun6i-a31-display-frontend * allwinner,sun7i-a20-display-frontend + * allwinner,sun8i-a23-display-frontend * allwinner,sun8i-a33-display-frontend * allwinner,sun9i-a80-display-frontend - reg: base address and size of the memory-mapped region. @@ -419,6 +423,7 @@ Required properties: * allwinner,sun6i-a31-display-engine * allwinner,sun6i-a31s-display-engine * allwinner,sun7i-a20-display-engine + * allwinner,sun8i-a23-display-engine * allwinner,sun8i-a33-display-engine * allwinner,sun8i-a83t-display-engine * allwinner,sun8i-h3-display-engine diff --git a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt index 593be44a53c9..9999255ac5b6 100644 --- a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt +++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt @@ -238,6 +238,9 @@ of the following host1x client modules: - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection - nvidia,edid: supplies a binary EDID blob - nvidia,panel: phandle of a display panel + - nvidia,xbar-cfg: 5 cells containing the crossbar configuration. Each lane + of the SOR, identified by the cell's index, is mapped via the crossbar to + the pad specified by the cell's value. Optional properties when driving an eDP output: - nvidia,dpaux: phandle to a DispayPort AUX interface diff --git a/Documentation/devicetree/bindings/edac/aspeed-sdram-edac.txt b/Documentation/devicetree/bindings/edac/aspeed-sdram-edac.txt new file mode 100644 index 000000000000..6a0f3d90d682 --- /dev/null +++ b/Documentation/devicetree/bindings/edac/aspeed-sdram-edac.txt @@ -0,0 +1,25 @@ +Aspeed AST2500 SoC EDAC node + +The Aspeed AST2500 SoC supports DDR3 and DDR4 memory with and without ECC (error +correction check). + +The memory controller supports SECDED (single bit error correction, double bit +error detection) and single bit error auto scrubbing by reserving 8 bits for +every 64 bit word (effectively reducing available memory to 8/9). + +Note, the bootloader must configure ECC mode in the memory controller. + + +Required properties: +- compatible: should be "aspeed,ast2500-sdram-edac" +- reg: sdram controller register set should be <0x1e6e0000 0x174> +- interrupts: should be AVIC interrupt #0 + + +Example: + + edac: sdram@1e6e0000 { + compatible = "aspeed,ast2500-sdram-edac"; + reg = <0x1e6e0000 0x174>; + interrupts = <0>; + }; diff --git a/Documentation/devicetree/bindings/eeprom/at24.txt b/Documentation/devicetree/bindings/eeprom/at24.txt index f9a7c984274c..0e456bbc1213 100644 --- a/Documentation/devicetree/bindings/eeprom/at24.txt +++ b/Documentation/devicetree/bindings/eeprom/at24.txt @@ -75,6 +75,8 @@ Optional properties: - address-width: number of address bits (one of 8, 16). + - num-addresses: total number of i2c slave addresses this device takes + Example: eeprom@52 { @@ -82,4 +84,5 @@ eeprom@52 { reg = <0x52>; pagesize = <32>; wp-gpios = <&gpio1 3 0>; + num-addresses = <8>; }; diff --git a/Documentation/devicetree/bindings/extcon/extcon-ptn5150.txt b/Documentation/devicetree/bindings/extcon/extcon-ptn5150.txt new file mode 100644 index 000000000000..936fbdf12815 --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/extcon-ptn5150.txt @@ -0,0 +1,27 @@ +* PTN5150 CC (Configuration Channel) Logic device + +PTN5150 is a small thin low power CC logic chip supporting the USB Type-C +connector application with CC control logic detection and indication functions. +It is interfaced to the host controller using an I2C interface. + +Required properties: +- compatible: should be "nxp,ptn5150" +- reg: specifies the I2C slave address of the device +- int-gpio: should contain a phandle and GPIO specifier for the GPIO pin + connected to the PTN5150's INTB pin. +- vbus-gpio: should contain a phandle and GPIO specifier for the GPIO pin which + is used to control VBUS. +- pinctrl-names : a pinctrl state named "default" must be defined. +- pinctrl-0 : phandle referencing pin configuration of interrupt and vbus + control. + +Example: + ptn5150@1d { + compatible = "nxp,ptn5150"; + reg = <0x1d>; + int-gpio = <&msmgpio 78 GPIO_ACTIVE_HIGH>; + vbus-gpio = <&msmgpio 148 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&ptn5150_default>; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/firmware/nvidia,tegra186-bpmp.txt b/Documentation/devicetree/bindings/firmware/nvidia,tegra186-bpmp.txt index 0c10802c8327..ff380dadb5f9 100644 --- a/Documentation/devicetree/bindings/firmware/nvidia,tegra186-bpmp.txt +++ b/Documentation/devicetree/bindings/firmware/nvidia,tegra186-bpmp.txt @@ -8,7 +8,6 @@ which can create the interprocessor communication (IPC) between the CPU and BPMP. Required properties: -- name : Should be bpmp - compatible Array of strings One of: diff --git a/Documentation/devicetree/bindings/firmware/nvidia,tegra210-bpmp.txt b/Documentation/devicetree/bindings/firmware/nvidia,tegra210-bpmp.txt new file mode 100644 index 000000000000..68d814e8c09d --- /dev/null +++ b/Documentation/devicetree/bindings/firmware/nvidia,tegra210-bpmp.txt @@ -0,0 +1,35 @@ +NVIDIA Tegra210 Boot and Power Management Processor (BPMP) + +The Boot and Power Management Processor (BPMP) is a co-processor found +in Tegra210 SoC. It is designed to handle the early stages of the boot +process as well as to assisting in entering deep low power state +(suspend to ram), and also offloading DRAM memory clock scaling on +some platforms. The binding document defines the resources that would +be used by the BPMP T210 firmware driver, which can create the +interprocessor communication (IPC) between the CPU and BPMP. + +Required properties: +- compatible + Array of strings + One of: + - "nvidia,tegra210-bpmp" +- reg: physical base address and length for HW synchornization primitives + 1) base address and length to Tegra 'atomics' hardware + 2) base address and length to Tegra 'semaphore' hardware +- interrupts: specifies the interrupt number for receiving messages ("rx") + and for triggering messages ("tx") + +Optional properties: +- #clock-cells : Should be 1 for platforms where DRAM clock control is + offloaded to bpmp. + +Example: + +bpmp@70016000 { + compatible = "nvidia,tegra210-bpmp"; + reg = <0x0 0x70016000 0x0 0x2000 + 0x0 0x60001000 0x0 0x1000>; + interrupts = <GIC_SPI 6 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 4 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "tx", "rx"; +}; diff --git a/Documentation/devicetree/bindings/gnss/gnss.txt b/Documentation/devicetree/bindings/gnss/gnss.txt index f1e4a2ff47c5..f547bd4549fe 100644 --- a/Documentation/devicetree/bindings/gnss/gnss.txt +++ b/Documentation/devicetree/bindings/gnss/gnss.txt @@ -17,6 +17,7 @@ Required properties: represents Optional properties: +- lna-supply : Separate supply for an LNA - enable-gpios : GPIO used to enable the device - timepulse-gpios : Time pulse GPIO diff --git a/Documentation/devicetree/bindings/gnss/mediatek.txt b/Documentation/devicetree/bindings/gnss/mediatek.txt new file mode 100644 index 000000000000..80cb802813c5 --- /dev/null +++ b/Documentation/devicetree/bindings/gnss/mediatek.txt @@ -0,0 +1,35 @@ +Mediatek-based GNSS Receiver DT binding + +Mediatek chipsets are used in GNSS-receiver modules produced by several +vendors and can use a UART interface. + +Please see Documentation/devicetree/bindings/gnss/gnss.txt for generic +properties. + +Required properties: + +- compatible : Must be + + "globaltop,pa6h" + +- vcc-supply : Main voltage regulator (pin name: VCC) + +Optional properties: + +- current-speed : Default UART baud rate +- gnss-fix-gpios : GPIO used to determine device position fix state + (pin name: FIX, 3D_FIX) +- reset-gpios : GPIO used to reset the device (pin name: RESET, NRESET) +- timepulse-gpios : Time pulse GPIO (pin name: PPS1, 1PPS) +- vbackup-supply : Backup voltage regulator (pin name: VBAT, VBACKUP) + +Example: + +serial@1234 { + compatible = "ns16550a"; + + gnss { + compatible = "globaltop,pa6h"; + vcc-supply = <&vcc_3v3>; + }; +}; diff --git a/Documentation/devicetree/bindings/gnss/sirfstar.txt b/Documentation/devicetree/bindings/gnss/sirfstar.txt index 648d183cdb77..f4252b6b660b 100644 --- a/Documentation/devicetree/bindings/gnss/sirfstar.txt +++ b/Documentation/devicetree/bindings/gnss/sirfstar.txt @@ -12,6 +12,7 @@ Required properties: "fastrax,uc430" "linx,r4" + "wi2wi,w2sg0004" "wi2wi,w2sg0008i" "wi2wi,w2sg0084i" diff --git a/Documentation/devicetree/bindings/gpio/gateworks,pld-gpio.txt b/Documentation/devicetree/bindings/gpio/gateworks,pld-gpio.txt new file mode 100644 index 000000000000..6e81f8b755c5 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gateworks,pld-gpio.txt @@ -0,0 +1,20 @@ +Gateworks PLD GPIO controller bindings + +The GPIO controller should be a child node on an I2C bus, +see: i2c/i2c.txt for details. + +Required properties: +- compatible: Should be "gateworks,pld-gpio" +- reg: I2C slave address +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Should be <2>. The first cell is the gpio number and + the second cell is used to specify optional parameters. + +Example: + +pld@56 { + compatible = "gateworks,pld-gpio"; + reg = <0x56>; + gpio-controller; + #gpio-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-eic-sprd.txt b/Documentation/devicetree/bindings/gpio/gpio-eic-sprd.txt index 93d98d09d92b..54040a2bfe3a 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-eic-sprd.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-eic-sprd.txt @@ -33,7 +33,7 @@ Required properties: "sprd,sc9860-eic-latch", "sprd,sc9860-eic-async", "sprd,sc9860-eic-sync", - "sprd,sc27xx-eic". + "sprd,sc2731-eic". - reg: Define the base and range of the I/O address space containing the GPIO controller registers. - gpio-controller: Marks the device node as a GPIO controller. @@ -86,7 +86,7 @@ Example: }; pmic_eic: gpio@300 { - compatible = "sprd,sc27xx-eic"; + compatible = "sprd,sc2731-eic"; reg = <0x300>; interrupt-parent = <&sc2731_pmic>; interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt index 38ca2201e8ae..2e097b57f170 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt @@ -14,8 +14,6 @@ Required properties: "marvell,armada-8k-gpio" should be used for the Armada 7K and 8K SoCs (either from AP or CP), see - Documentation/devicetree/bindings/arm/marvell/cp110-system-controller0.txt - and Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt for specific details about the offset property. diff --git a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt index 4e3c550e319a..fb144e2b6522 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt @@ -16,6 +16,7 @@ Required properties: nxp,pca9574 nxp,pca9575 nxp,pca9698 + nxp,pcal6416 nxp,pcal6524 nxp,pcal9555a maxim,max7310 diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index f0ba154b5723..a8895d339bfe 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -67,6 +67,18 @@ Optional standard bitfield specifiers for the last cell: https://en.wikipedia.org/wiki/Open_collector - Bit 3: 0 means the output should be maintained during sleep/low-power mode 1 means the output state can be lost during sleep/low-power mode +- Bit 4: 0 means no pull-up resistor should be enabled + 1 means a pull-up resistor should be enabled + This setting only applies to hardware with a simple on/off + control for pull-up configuration. If the hardware has more + elaborate pull-up configuration, it should be represented + using a pin control binding. +- Bit 5: 0 means no pull-down resistor should be enabled + 1 means a pull-down resistor should be enabled + This setting only applies to hardware with a simple on/off + control for pull-down configuration. If the hardware has more + elaborate pull-down configuration, it should be represented + using a pin control binding. 1.1) GPIO specifier best practices ---------------------------------- diff --git a/Documentation/devicetree/bindings/gpio/intel,ixp4xx-gpio.txt b/Documentation/devicetree/bindings/gpio/intel,ixp4xx-gpio.txt new file mode 100644 index 000000000000..8dc41ed99685 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/intel,ixp4xx-gpio.txt @@ -0,0 +1,38 @@ +Intel IXP4xx XScale Networking Processors GPIO + +This GPIO controller is found in the Intel IXP4xx processors. +It supports 16 GPIO lines. + +The interrupt portions of the GPIO controller is hierarchical: +the synchronous edge detector is part of the GPIO block, but the +actual enabling/disabling of the interrupt line is done in the +main IXP4xx interrupt controller which has a 1:1 mapping for +the first 12 GPIO lines to 12 system interrupts. + +The remaining 4 GPIO lines can not be used for receiving +interrupts. + +The interrupt parent of this GPIO controller must be the +IXP4xx interrupt controller. + +Required properties: + +- compatible : Should be + "intel,ixp4xx-gpio" +- reg : Should contain registers location and length +- gpio-controller : marks this as a GPIO controller +- #gpio-cells : Should be 2, see gpio/gpio.txt +- interrupt-controller : marks this as an interrupt controller +- #interrupt-cells : a standard two-cell interrupt, see + interrupt-controller/interrupts.txt + +Example: + +gpio0: gpio@c8004000 { + compatible = "intel,ixp4xx-gpio"; + reg = <0xc8004000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt index 3f128e4f95c6..ae63f09fda7d 100644 --- a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt +++ b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt @@ -13,6 +13,8 @@ Required properties: + allwinner,sun8i-h3-mali + allwinner,sun50i-a64-mali + allwinner,sun50i-h5-mali + + amlogic,meson8-mali + + amlogic,meson8b-mali + amlogic,meson-gxbb-mali + amlogic,meson-gxl-mali + rockchip,rk3036-mali @@ -82,6 +84,10 @@ to specify one more vendor-specific compatible, among: Required properties: * resets: phandle to the reset line for the GPU + - amlogic,meson8-mali and amlogic,meson8b-mali + Required properties: + * resets: phandle to the reset line for the GPU + - Rockchip variants: Required properties: * resets: phandle to the reset line for the GPU diff --git a/Documentation/devicetree/bindings/gpu/samsung-rotator.txt b/Documentation/devicetree/bindings/gpu/samsung-rotator.txt index 82cd1ed0be93..3aca2578da0b 100644 --- a/Documentation/devicetree/bindings/gpu/samsung-rotator.txt +++ b/Documentation/devicetree/bindings/gpu/samsung-rotator.txt @@ -2,9 +2,10 @@ Required properties: - compatible : value should be one of the following: - (a) "samsung,exynos4210-rotator" for Rotator IP in Exynos4210 - (b) "samsung,exynos4212-rotator" for Rotator IP in Exynos4212/4412 - (c) "samsung,exynos5250-rotator" for Rotator IP in Exynos5250 + * "samsung,s5pv210-rotator" for Rotator IP in S5PV210 + * "samsung,exynos4210-rotator" for Rotator IP in Exynos4210 + * "samsung,exynos4212-rotator" for Rotator IP in Exynos4212/4412 + * "samsung,exynos5250-rotator" for Rotator IP in Exynos5250 - reg : Physical base address of the IP registers and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/hwmon/ad741x.txt b/Documentation/devicetree/bindings/hwmon/ad741x.txt new file mode 100644 index 000000000000..9102152c8410 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/ad741x.txt @@ -0,0 +1,15 @@ +* AD7416/AD7417/AD7418 Temperature Sensor Device Tree Bindings + +Required properties: +- compatible: one of + "adi,ad7416" + "adi,ad7417" + "adi,ad7418" +- reg: I2C address + +Example: + +hwmon@28 { + compatible = "adi,ad7418"; + reg = <0x28>; +}; diff --git a/Documentation/devicetree/bindings/hwmon/dps650ab.txt b/Documentation/devicetree/bindings/hwmon/dps650ab.txt new file mode 100644 index 000000000000..76780e795899 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/dps650ab.txt @@ -0,0 +1,11 @@ +Bindings for Delta Electronics DPS-650-AB power supply + +Required properties: +- compatible : "delta,dps650ab" +- reg : I2C address, one of 0x58, 0x59. + +Example: + dps650ab@58 { + compatible = "delta,dps650ab"; + reg = <0x58>; + }; diff --git a/Documentation/devicetree/bindings/hwmon/hih6130.txt b/Documentation/devicetree/bindings/hwmon/hih6130.txt new file mode 100644 index 000000000000..2c43837af4c2 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/hih6130.txt @@ -0,0 +1,12 @@ +Honeywell Humidicon HIH-6130 humidity/temperature sensor +-------------------------------------------------------- + +Requires node properties: +- compatible : "honeywell,hi6130" +- reg : the I2C address of the device. This is 0x27. + +Example: + hih6130@27 { + compatible = "honeywell,hih6130"; + reg = <0x27>; + }; diff --git a/Documentation/devicetree/bindings/hwmon/ina3221.txt b/Documentation/devicetree/bindings/hwmon/ina3221.txt index a7b25caa2b8e..fa63b6171407 100644 --- a/Documentation/devicetree/bindings/hwmon/ina3221.txt +++ b/Documentation/devicetree/bindings/hwmon/ina3221.txt @@ -6,6 +6,16 @@ Texas Instruments INA3221 Device Tree Bindings - reg: I2C address Optional properties: + - ti,single-shot: This chip has two power modes: single-shot (chip takes one + measurement and then shuts itself down) and continuous ( + chip takes continuous measurements). The continuous mode is + more reliable and suitable for hardware monitor type device, + but the single-shot mode is more power-friendly and useful + for battery-powered device which cares power consumptions + while still needs some measurements occasionally. + If this property is present, the single-shot mode will be + used, instead of the default continuous one for monitoring. + = The node contains optional child nodes for three channels = = Each child node describes the information of input source = diff --git a/Documentation/devicetree/bindings/hwmon/lm75.txt b/Documentation/devicetree/bindings/hwmon/lm75.txt new file mode 100644 index 000000000000..12d8cf7cf592 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/lm75.txt @@ -0,0 +1,37 @@ +*LM75 hwmon sensor. + +Required properties: +- compatible: manufacturer and chip name, one of + "adi,adt75", + "dallas,ds1775", + "dallas,ds75", + "dallas,ds7505", + "gmt,g751", + "national,lm75", + "national,lm75a", + "national,lm75b", + "maxim,max6625", + "maxim,max6626", + "maxim,max31725", + "maxim,max31726", + "maxim,mcp980x", + "st,stds75", + "st,stlm75", + "microchip,tcn75", + "ti,tmp100", + "ti,tmp101", + "ti,tmp105", + "ti,tmp112", + "ti,tmp175", + "ti,tmp275", + "ti,tmp75", + "ti,tmp75c", + +- reg: I2C bus address of the device + +Example: + +sensor@48 { + compatible = "st,stlm75"; + reg = <0x48>; +}; diff --git a/Documentation/devicetree/bindings/hwmon/pwm-fan.txt b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt index c6d533202d3e..49ca5d83ed13 100644 --- a/Documentation/devicetree/bindings/hwmon/pwm-fan.txt +++ b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt @@ -6,6 +6,9 @@ Required properties: - cooling-levels : PWM duty cycle values in a range from 0 to 255 which correspond to thermal cooling states +Optional properties: +- fan-supply : phandle to the regulator that provides power to the fan + Example: fan0: pwm-fan { compatible = "pwm-fan"; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mtk.txt b/Documentation/devicetree/bindings/i2c/i2c-mtk.txt index e199695b1c96..ee4c32454198 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mtk.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mtk.txt @@ -10,6 +10,7 @@ Required properties: "mediatek,mt6589-i2c": for MediaTek MT6589 "mediatek,mt7622-i2c": for MediaTek MT7622 "mediatek,mt7623-i2c", "mediatek,mt6577-i2c": for MediaTek MT7623 + "mediatek,mt7629-i2c", "mediatek,mt2712-i2c": for MediaTek MT7629 "mediatek,mt8173-i2c": for MediaTek MT8173 - reg: physical base address of the controller and dma base, length of memory mapped region. diff --git a/Documentation/devicetree/bindings/i2c/i2c-xscale.txt b/Documentation/devicetree/bindings/i2c/i2c-xscale.txt new file mode 100644 index 000000000000..dcc8390e0d24 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-xscale.txt @@ -0,0 +1,20 @@ +i2c Controller on XScale platforms such as IOP3xx and IXP4xx + +Required properties: +- compatible : Must be one of + "intel,iop3xx-i2c" + "intel,ixp4xx-i2c"; +- reg +- #address-cells = <1>; +- #size-cells = <0>; + +Optional properties: +- Child nodes conforming to i2c bus binding + +Example: + +i2c@c8011000 { + compatible = "intel,ixp4xx-i2c"; + reg = <0xc8011000 0x18>; + interrupts = <33 IRQ_TYPE_LEVEL_LOW>; +}; diff --git a/Documentation/devicetree/bindings/iio/accel/mma8452.txt b/Documentation/devicetree/bindings/iio/accel/mma8452.txt index 2100e9af379c..e132394375a1 100644 --- a/Documentation/devicetree/bindings/iio/accel/mma8452.txt +++ b/Documentation/devicetree/bindings/iio/accel/mma8452.txt @@ -20,6 +20,10 @@ Optional properties: - interrupt-names: should contain "INT1" and/or "INT2", the accelerometer's interrupt line in use. + - vdd-supply: phandle to the regulator that provides vdd power to the accelerometer. + + - vddio-supply: phandle to the regulator that provides vddio power to the accelerometer. + Example: mma8453fc@1d { diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt new file mode 100644 index 000000000000..d7b6241ca881 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt @@ -0,0 +1,65 @@ +Analog Devices AD7606 Simultaneous Sampling ADC + +Required properties for the AD7606: + +- compatible: Must be one of + * "adi,ad7605-4" + * "adi,ad7606-8" + * "adi,ad7606-6" + * "adi,ad7606-4" +- reg: SPI chip select number for the device +- spi-max-frequency: Max SPI frequency to use + see: Documentation/devicetree/bindings/spi/spi-bus.txt +- spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt +- avcc-supply: phandle to the Avcc power supply +- interrupts: IRQ line for the ADC + see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +- adi,conversion-start-gpios: must be the device tree identifier of the CONVST pin. + This logic input is used to initiate conversions on the analog + input channels. As the line is active high, it should be marked + GPIO_ACTIVE_HIGH. + +Optional properties: + +- reset-gpios: must be the device tree identifier of the RESET pin. If specified, + it will be asserted during driver probe. As the line is active high, + it should be marked GPIO_ACTIVE_HIGH. +- standby-gpios: must be the device tree identifier of the STBY pin. This pin is used + to place the AD7606 into one of two power-down modes, Standby mode or + Shutdown mode. As the line is active low, it should be marked + GPIO_ACTIVE_LOW. +- adi,first-data-gpios: must be the device tree identifier of the FRSTDATA pin. + The FRSTDATA output indicates when the first channel, V1, is + being read back on either the parallel, byte or serial interface. + As the line is active high, it should be marked GPIO_ACTIVE_HIGH. +- adi,range-gpios: must be the device tree identifier of the RANGE pin. The polarity on + this pin determines the input range of the analog input channels. If + this pin is tied to a logic high, the analog input range is ±10V for + all channels. If this pin is tied to a logic low, the analog input range + is ±5V for all channels. As the line is active high, it should be marked + GPIO_ACTIVE_HIGH. +- adi,oversampling-ratio-gpios: must be the device tree identifier of the over-sampling + mode pins. As the line is active high, it should be marked + GPIO_ACTIVE_HIGH. + +Example: + + adc@0 { + compatible = "adi,ad7606-8"; + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpol; + + avcc-supply = <&adc_vref>; + + interrupts = <25 IRQ_TYPE_EDGE_FALLING>; + interrupt-parent = <&gpio>; + + adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>; + adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; + adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH + &gpio 23 GPIO_ACTIVE_HIGH + &gpio 26 GPIO_ACTIVE_HIGH>; + standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.txt new file mode 100644 index 000000000000..9f5b88cf680d --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.txt @@ -0,0 +1,41 @@ +Analog Devices AD7768-1 ADC device driver + +Required properties for the AD7768-1: + +- compatible: Must be "adi,ad7768-1" +- reg: SPI chip select number for the device +- spi-max-frequency: Max SPI frequency to use + see: Documentation/devicetree/bindings/spi/spi-bus.txt +- clocks: phandle to the master clock (mclk) + see: Documentation/devicetree/bindings/clock/clock-bindings.txt +- clock-names: Must be "mclk". +- interrupts: IRQ line for the ADC + see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +- vref-supply: vref supply can be used as reference for conversion +- adi,sync-in-gpios: must be the device tree identifier of the SYNC-IN pin. Enables + synchronization of multiple devices that require simultaneous sampling. + A pulse is always required if the configuration is changed in any way, for example + if the filter decimation rate changes. As the line is active low, it should + be marked GPIO_ACTIVE_LOW. + +Optional properties: + + - reset-gpios : GPIO spec for the RESET pin. If specified, it will be asserted during + driver probe. As the line is active low, it should be marked GPIO_ACTIVE_LOW. + +Example: + + adc@0 { + compatible = "adi,ad7768-1"; + reg = <0>; + spi-max-frequency = <2000000>; + spi-cpol; + spi-cpha; + vref-supply = <&adc_vref>; + interrupts = <25 IRQ_TYPE_EDGE_RISING>; + interrupt-parent = <&gpio>; + adi,sync-in-gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio 27 GPIO_ACTIVE_LOW>; + clocks = <&ad7768_mclk>; + clock-names = "mclk"; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt index 325090e43ce6..75c775954102 100644 --- a/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt +++ b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt @@ -23,6 +23,10 @@ Required properties: - #io-channel-cells: must be 1, see ../iio-bindings.txt Optional properties: +- amlogic,hhi-sysctrl: phandle to the syscon which contains the 5th bit + of the TSC (temperature sensor coefficient) on + Meson8b and Meson8m2 (which used to calibrate the + temperature sensor) - nvmem-cells: phandle to the temperature_calib eFuse cells - nvmem-cell-names: if present (to enable the temperature sensor calibration) this must contain "temperature_calib" diff --git a/Documentation/devicetree/bindings/iio/adc/ingenic,adc.txt b/Documentation/devicetree/bindings/iio/adc/ingenic,adc.txt new file mode 100644 index 000000000000..f01159f20d87 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ingenic,adc.txt @@ -0,0 +1,48 @@ +* Ingenic JZ47xx ADC controller IIO bindings + +Required properties: + +- compatible: Should be one of: + * ingenic,jz4725b-adc + * ingenic,jz4740-adc +- reg: ADC controller registers location and length. +- clocks: phandle to the SoC's ADC clock. +- clock-names: Must be set to "adc". +- #io-channel-cells: Must be set to <1> to indicate channels are selected + by index. + +ADC clients must use the format described in iio-bindings.txt, giving +a phandle and IIO specifier pair ("io-channels") to the ADC controller. + +Example: + +#include <dt-bindings/iio/adc/ingenic,adc.h> + +adc: adc@10070000 { + compatible = "ingenic,jz4740-adc"; + #io-channel-cells = <1>; + + reg = <0x10070000 0x30>; + + clocks = <&cgu JZ4740_CLK_ADC>; + clock-names = "adc"; + + interrupt-parent = <&intc>; + interrupts = <18>; +}; + +adc-keys { + ... + compatible = "adc-keys"; + io-channels = <&adc INGENIC_ADC_AUX>; + io-channel-names = "buttons"; + ... +}; + +battery { + ... + compatible = "ingenic,jz4740-battery"; + io-channels = <&adc INGENIC_ADC_BATTERY>; + io-channel-names = "battery"; + ... +}; diff --git a/Documentation/devicetree/bindings/staging/iio/adc/lpc32xx-adc.txt b/Documentation/devicetree/bindings/iio/adc/lpc32xx-adc.txt index b3629d3a9adf..b3629d3a9adf 100644 --- a/Documentation/devicetree/bindings/staging/iio/adc/lpc32xx-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/lpc32xx-adc.txt diff --git a/Documentation/devicetree/bindings/iio/adc/nuvoton,npcm-adc.txt b/Documentation/devicetree/bindings/iio/adc/nuvoton,npcm-adc.txt new file mode 100644 index 000000000000..eb939fe77836 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/nuvoton,npcm-adc.txt @@ -0,0 +1,24 @@ +Nuvoton NPCM Analog to Digital Converter (ADC) + +The NPCM ADC is a 10-bit converter for eight channel inputs. + +Required properties: +- compatible: "nuvoton,npcm750-adc" for the NPCM7XX BMC. +- reg: specifies physical base address and size of the registers. +- interrupts: Contain the ADC interrupt with flags for falling edge. + +Optional properties: +- clocks: phandle of ADC reference clock, in case the clock is not + added the ADC will use the default ADC sample rate. +- vref-supply: The regulator supply ADC reference voltage, in case the + vref-supply is not added the ADC will use internal voltage + reference. + +Example: + +adc: adc@f000c000 { + compatible = "nuvoton,npcm750-adc"; + reg = <0xf000c000 0x8>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk NPCM7XX_CLK_ADC>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.txt b/Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.txt index a10c1f89037d..e1fe02f3e3e9 100644 --- a/Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.txt @@ -11,11 +11,13 @@ New driver handles the following Required properties: - compatible: Must be "samsung,exynos-adc-v1" - for exynos4412/5250 controllers. + for Exynos5250 controllers. Must be "samsung,exynos-adc-v2" for future controllers. Must be "samsung,exynos3250-adc" for controllers compatible with ADC of Exynos3250. + Must be "samsung,exynos4212-adc" for + controllers compatible with ADC of Exynos4212 and Exynos4412. Must be "samsung,exynos7-adc" for the ADC in Exynos7 and compatibles Must be "samsung,s3c2410-adc" for diff --git a/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt b/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt new file mode 100644 index 000000000000..480e66422625 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt @@ -0,0 +1,21 @@ +STMPE ADC driver +---------------- + +Required properties: + - compatible: "st,stmpe-adc" + +Optional properties: +Note that the ADC is shared with the STMPE touchscreen. ADC related settings +have to be done in the mfd. +- st,norequest-mask: bitmask specifying which ADC channels should _not_ be + requestable due to different usage (e.g. touch) + +Node name must be stmpe_adc and should be child node of stmpe node to +which it belongs. + +Example: + + stmpe_adc { + compatible = "st,stmpe-adc"; + st,norequest-mask = <0x0F>; /* dont use ADC CH3-0 */ + }; diff --git a/Documentation/devicetree/bindings/iio/adc/ti-ads124s08.txt b/Documentation/devicetree/bindings/iio/adc/ti-ads124s08.txt new file mode 100644 index 000000000000..ecf807bb32f7 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti-ads124s08.txt @@ -0,0 +1,25 @@ +* Texas Instruments' ads124s08 and ads124s06 ADC chip + +Required properties: + - compatible : + "ti,ads124s08" + "ti,ads124s06" + - reg : spi chip select number for the device + +Recommended properties: + - spi-max-frequency : Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + - spi-cpha : Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Optional properties: + - reset-gpios : GPIO pin used to reset the device. + +Example: +adc@0 { + compatible = "ti,ads124s08"; + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpha; + reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; +}; diff --git a/Documentation/devicetree/bindings/iio/chemical/bme680.txt b/Documentation/devicetree/bindings/iio/chemical/bme680.txt new file mode 100644 index 000000000000..7f3827cfb2ff --- /dev/null +++ b/Documentation/devicetree/bindings/iio/chemical/bme680.txt @@ -0,0 +1,11 @@ +Bosch Sensortec BME680 pressure/temperature/humidity/voc sensors + +Required properties: +- compatible: must be "bosch,bme680" + +Example: + +bme680@76 { + compatible = "bosch,bme680"; + reg = <0x76>; +}; diff --git a/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt b/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt new file mode 100644 index 000000000000..7b5f06f324c8 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt @@ -0,0 +1,20 @@ +* Plantower PMS7003 particulate matter sensor + +Required properties: +- compatible: must be "plantower,pms7003" +- vcc-supply: phandle to the regulator that provides power to the sensor + +Optional properties: +- plantower,set-gpios: phandle to the GPIO connected to the SET line +- reset-gpios: phandle to the GPIO connected to the RESET line + +Refer to serial/slave-device.txt for generic serial attached device bindings. + +Example: + +&uart0 { + air-pollution-sensor { + compatible = "plantower,pms7003"; + vcc-supply = <®_vcc5v0>; + }; +}; diff --git a/Documentation/devicetree/bindings/iio/chemical/sensirion,sgp30.txt b/Documentation/devicetree/bindings/iio/chemical/sensirion,sgp30.txt new file mode 100644 index 000000000000..5844ed58173c --- /dev/null +++ b/Documentation/devicetree/bindings/iio/chemical/sensirion,sgp30.txt @@ -0,0 +1,15 @@ +* Sensirion SGP30/SGPC3 multi-pixel Gas Sensor + +Required properties: + + - compatible: must be one of + "sensirion,sgp30" + "sensirion,sgpc3" + - reg: the I2C address of the sensor + +Example: + +gas@58 { + compatible = "sensirion,sgp30"; + reg = <0x58>; +}; diff --git a/Documentation/devicetree/bindings/iio/chemical/sensirion,sps30.txt b/Documentation/devicetree/bindings/iio/chemical/sensirion,sps30.txt new file mode 100644 index 000000000000..6eee2709b5b6 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/chemical/sensirion,sps30.txt @@ -0,0 +1,12 @@ +* Sensirion SPS30 particulate matter sensor + +Required properties: +- compatible: must be "sensirion,sps30" +- reg: the I2C address of the sensor + +Example: + +sps30@69 { + compatible = "sensirion,sps30"; + reg = <0x69>; +}; diff --git a/Documentation/devicetree/bindings/iio/dac/ti,dac7612.txt b/Documentation/devicetree/bindings/iio/dac/ti,dac7612.txt new file mode 100644 index 000000000000..639c94ed83e9 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/ti,dac7612.txt @@ -0,0 +1,28 @@ +* Texas Instruments Dual, 12-Bit Serial Input Digital-to-Analog Converter + +The DAC7612 is a dual, 12-bit digital-to-analog converter (DAC) with guaranteed +12-bit monotonicity performance over the industrial temperature range. +Is is programmable through an SPI interface. + +The internal DACs are loaded when the LOADDACS pin is pulled down. + +http://www.ti.com/lit/ds/sbas106/sbas106.pdf + +Required Properties: +- compatible: Should be one of: + "ti,dac7612" + "ti,dac7612u" + "ti,dac7612ub" +- reg: Definition as per Documentation/devicetree/bindings/spi/spi-bus.txt + +Optional Properties: +- ti,loaddacs-gpios: GPIO descriptor for the LOADDACS pin. +- spi-*: Definition as per Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + + dac@1 { + compatible = "ti,dac7612"; + reg = <0x1>; + ti,loaddacs-gpios = <&msmgpio 25 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/iio/impedance-analyzer/ad5933.txt b/Documentation/devicetree/bindings/iio/impedance-analyzer/ad5933.txt new file mode 100644 index 000000000000..5ff38728ff91 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/impedance-analyzer/ad5933.txt @@ -0,0 +1,26 @@ +Analog Devices AD5933/AD5934 Impedance Converter, Network Analyzer + +https://www.analog.com/media/en/technical-documentation/data-sheets/AD5933.pdf +https://www.analog.com/media/en/technical-documentation/data-sheets/AD5934.pdf + +Required properties: + - compatible : should be one of + "adi,ad5933" + "adi,ad5934" + - reg : the I2C address. + - vdd-supply : The regulator supply for DVDD, AVDD1 and AVDD2 when they + are connected together. + +Optional properties: +- clocks : external clock reference. +- clock-names : must be "mclk" if clocks is set. + +Example for a I2C device node: + + impedance-analyzer@0d { + compatible = "adi,adxl345"; + reg = <0x0d>; + vdd-supply = <&vdd_supply>; + clocks = <&ref_clk>; + clock-names = "mclk"; + }; diff --git a/Documentation/devicetree/bindings/iio/imu/bmi160.txt b/Documentation/devicetree/bindings/iio/imu/bmi160.txt index 0c1c105fb503..900c169de00f 100644 --- a/Documentation/devicetree/bindings/iio/imu/bmi160.txt +++ b/Documentation/devicetree/bindings/iio/imu/bmi160.txt @@ -9,9 +9,11 @@ Required properties: - spi-max-frequency : set maximum clock frequency (only for SPI) Optional properties: - - interrupts : interrupt mapping for IRQ, must be IRQ_TYPE_LEVEL_LOW + - interrupts : interrupt mapping for IRQ - interrupt-names : set to "INT1" if INT1 pin should be used as interrupt input, set to "INT2" if INT2 pin should be used instead + - drive-open-drain : set if the specified interrupt pin should be configured as + open drain. If not set, defaults to push-pull. Examples: @@ -20,7 +22,7 @@ bmi160@68 { reg = <0x68>; interrupt-parent = <&gpio4>; - interrupts = <12 IRQ_TYPE_LEVEL_LOW>; + interrupts = <12 IRQ_TYPE_EDGE_RISING>; interrupt-names = "INT1"; }; diff --git a/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt b/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt index 6ab9a9d196b0..268bf7568e19 100644 --- a/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt +++ b/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt @@ -11,6 +11,7 @@ Required properties: "invensense,mpu9250" "invensense,mpu9255" "invensense,icm20608" + "invensense,icm20602" - reg : the I2C address of the sensor - interrupts: interrupt mapping for IRQ. It should be configured with flags IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_EDGE_RISING, IRQ_TYPE_LEVEL_LOW or diff --git a/Documentation/devicetree/bindings/iio/light/max44009.txt b/Documentation/devicetree/bindings/iio/light/max44009.txt new file mode 100644 index 000000000000..4a98848e35c0 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/max44009.txt @@ -0,0 +1,24 @@ +* MAX44009 Ambient Light Sensor + +Required properties: + +- compatible: should be "maxim,max44009" +- reg: the I2C address of the device (default is <0x4a>) + +Optional properties: + +- interrupts: interrupt mapping for GPIO IRQ. Should be configured with + IRQ_TYPE_EDGE_FALLING. + +Refer to interrupt-controller/interrupts.txt for generic interrupt client +node bindings. + +Example: + +light-sensor@4a { + compatible = "maxim,max44009"; + reg = <0x4a>; + + interrupt-parent = <&gpio1>; + interrupts = <17 IRQ_TYPE_EDGE_FALLING>; +}; diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt index ddcb95509599..52ee4baec6f0 100644 --- a/Documentation/devicetree/bindings/iio/st-sensors.txt +++ b/Documentation/devicetree/bindings/iio/st-sensors.txt @@ -77,3 +77,4 @@ Pressure sensors: - st,lps22hb-press - st,lps33hw - st,lps35hw +- st,lps22hh diff --git a/Documentation/devicetree/bindings/input/st,stpmic1-onkey.txt b/Documentation/devicetree/bindings/input/st,stpmic1-onkey.txt new file mode 100644 index 000000000000..4494613ae7ad --- /dev/null +++ b/Documentation/devicetree/bindings/input/st,stpmic1-onkey.txt @@ -0,0 +1,28 @@ +STMicroelectronics STPMIC1 Onkey + +Required properties: + +- compatible = "st,stpmic1-onkey"; +- interrupts: interrupt line to use +- interrupt-names = "onkey-falling", "onkey-rising" + onkey-falling: happens when onkey is pressed; IT_PONKEY_F of pmic + onkey-rising: happens when onkey is released; IT_PONKEY_R of pmic + +Optional properties: + +- st,onkey-clear-cc-flag: onkey is able power on after an + over-current shutdown event. +- st,onkey-pu-inactive: onkey pull up is not active +- power-off-time-sec: Duration in seconds which the key should be kept + pressed for device to power off automatically (from 1 to 16 seconds). + see See Documentation/devicetree/bindings/input/keys.txt + +Example: + +onkey { + compatible = "st,stpmic1-onkey"; + interrupt-parent = <&pmic>; + interrupts = <IT_PONKEY_F 0>,<IT_PONKEY_R 1>; + interrupt-names = "onkey-falling", "onkey-rising"; + power-off-time-sec = <10>; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt index 127baa31a77a..c549924603d2 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt @@ -5,39 +5,105 @@ Required properties: - compatible: "st,stmpe-ts" Optional properties: -- st,sample-time: ADC converstion time in number of clock. (0 -> 36 clocks, 1 -> - 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks, 4 -> 80 clocks, 5 -> 96 clocks, 6 - -> 144 clocks), recommended is 4. -- st,mod-12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC) -- st,ref-sel: ADC reference source (0 -> internal reference, 1 -> external - reference) -- st,adc-freq: ADC Clock speed (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> 6.5 MHz) -- st,ave-ctrl: Sample average control (0 -> 1 sample, 1 -> 2 samples, 2 -> 4 - samples, 3 -> 8 samples) -- st,touch-det-delay: Touch detect interrupt delay (0 -> 10 us, 1 -> 50 us, 2 -> - 100 us, 3 -> 500 us, 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms) recommended - is 3 -- st,settling: Panel driver settling time (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3 - -> 1 ms, 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms) recommended is 2 -- st,fraction-z: Length of the fractional part in z (fraction-z ([0..7]) = Count of - the fractional part) recommended is 7 -- st,i-drive: current limit value of the touchscreen drivers (0 -> 20 mA typical 35 - mA max, 1 -> 50 mA typical 80 mA max) +- st,ave-ctrl : Sample average control + 0 -> 1 sample + 1 -> 2 samples + 2 -> 4 samples + 3 -> 8 samples +- st,touch-det-delay : Touch detect interrupt delay (recommended is 3) + 0 -> 10 us + 1 -> 50 us + 2 -> 100 us + 3 -> 500 us + 4 -> 1 ms + 5 -> 5 ms + 6 -> 10 ms + 7 -> 50 ms +- st,settling : Panel driver settling time (recommended is 2) + 0 -> 10 us + 1 -> 100 us + 2 -> 500 us + 3 -> 1 ms + 4 -> 5 ms + 5 -> 10 ms + 6 -> 50 ms + 7 -> 100 ms +- st,fraction-z : Length of the fractional part in z (recommended is 7) + (fraction-z ([0..7]) = Count of the fractional part) +- st,i-drive : current limit value of the touchscreen drivers + 0 -> 20 mA (typical 35mA max) + 1 -> 50 mA (typical 80 mA max) + +Optional properties common with MFD (deprecated): + - st,sample-time : ADC conversion time in number of clock. + 0 -> 36 clocks + 1 -> 44 clocks + 2 -> 56 clocks + 3 -> 64 clocks + 4 -> 80 clocks (recommended) + 5 -> 96 clocks + 6 -> 124 clocks + - st,mod-12b : ADC Bit mode + 0 -> 10bit ADC + 1 -> 12bit ADC + - st,ref-sel : ADC reference source + 0 -> internal + 1 -> external + - st,adc-freq : ADC Clock speed + 0 -> 1.625 MHz + 1 -> 3.25 MHz + 2 || 3 -> 6.5 MHz Node name must be stmpe_touchscreen and should be child node of stmpe node to which it belongs. +Note that common ADC settings of stmpe_touchscreen (child) will take precedence +over the settings done in MFD. + Example: +stmpe811@41 { + compatible = "st,stmpe811"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_touch_int>; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x41>; + interrupts = <10 IRQ_TYPE_LEVEL_LOW>; + interrupt-parent = <&gpio4>; + interrupt-controller; + id = <0>; + blocks = <0x5>; + irq-trigger = <0x1>; + /* Common ADC settings */ + /* 3.25 MHz ADC clock speed */ + st,adc-freq = <1>; + /* 12-bit ADC */ + st,mod-12b = <1>; + /* internal ADC reference */ + st,ref-sel = <0>; + /* ADC converstion time: 80 clocks */ + st,sample-time = <4>; + stmpe_touchscreen { compatible = "st,stmpe-ts"; - st,sample-time = <4>; - st,mod-12b = <1>; - st,ref-sel = <0>; - st,adc-freq = <1>; - st,ave-ctrl = <1>; - st,touch-det-delay = <2>; - st,settling = <2>; + reg = <0>; + /* 8 sample average control */ + st,ave-ctrl = <3>; + /* 5 ms touch detect interrupt delay */ + st,touch-det-delay = <5>; + /* 1 ms panel driver settling time */ + st,settling = <3>; + /* 7 length fractional part in z */ st,fraction-z = <7>; + /* + * 50 mA typical 80 mA max touchscreen drivers + * current limit value + */ st,i-drive = <1>; }; + stmpe_adc { + compatible = "st,stmpe-adc"; + st,norequest-mask = <0x0F>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt index b1163bf97146..aad5e34965eb 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt @@ -2,7 +2,12 @@ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Required properties: +- mfd + compatible: Should be + "ti,am3359-tscadc" for AM335x/AM437x SoCs + "ti,am654-tscadc", "ti,am3359-tscadc" for AM654 SoCs - child "tsc" + compatible: Should be "ti,am3359-tsc". ti,wires: Wires refer to application modes i.e. 4/5/8 wire touchscreen support on the platform. ti,x-plate-resistance: X plate resistance @@ -25,6 +30,9 @@ Required properties: AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7. XP = 0, XN = 1, YP = 2, YN = 3. - child "adc" + compatible: Should be + "ti,am3359-adc" for AM335x/AM437x SoCs + "ti,am654-adc", "ti,am3359-adc" for AM654 SoCs ti,adc-channels: List of analog inputs available for ADC. AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7. diff --git a/Documentation/devicetree/bindings/interconnect/interconnect.txt b/Documentation/devicetree/bindings/interconnect/interconnect.txt new file mode 100644 index 000000000000..5a3c575b387a --- /dev/null +++ b/Documentation/devicetree/bindings/interconnect/interconnect.txt @@ -0,0 +1,60 @@ +Interconnect Provider Device Tree Bindings +========================================= + +The purpose of this document is to define a common set of generic interconnect +providers/consumers properties. + + += interconnect providers = + +The interconnect provider binding is intended to represent the interconnect +controllers in the system. Each provider registers a set of interconnect +nodes, which expose the interconnect related capabilities of the interconnect +to consumer drivers. These capabilities can be throughput, latency, priority +etc. The consumer drivers set constraints on interconnect path (or endpoints) +depending on the use case. Interconnect providers can also be interconnect +consumers, such as in the case where two network-on-chip fabrics interface +directly. + +Required properties: +- compatible : contains the interconnect provider compatible string +- #interconnect-cells : number of cells in a interconnect specifier needed to + encode the interconnect node id + +Example: + + snoc: interconnect@580000 { + compatible = "qcom,msm8916-snoc"; + #interconnect-cells = <1>; + reg = <0x580000 0x14000>; + clock-names = "bus_clk", "bus_a_clk"; + clocks = <&rpmcc RPM_SMD_SNOC_CLK>, + <&rpmcc RPM_SMD_SNOC_A_CLK>; + }; + + += interconnect consumers = + +The interconnect consumers are device nodes which dynamically express their +bandwidth requirements along interconnect paths they are connected to. There +can be multiple interconnect providers on a SoC and the consumer may consume +multiple paths from different providers depending on use case and the +components it has to interact with. + +Required properties: +interconnects : Pairs of phandles and interconnect provider specifier to denote + the edge source and destination ports of the interconnect path. + +Optional properties: +interconnect-names : List of interconnect path name strings sorted in the same + order as the interconnects property. Consumers drivers will use + interconnect-names to match interconnect paths with interconnect + specifier pairs. + +Example: + + sdhci@7864000 { + ... + interconnects = <&pnoc MASTER_SDCC_1 &bimc SLAVE_EBI_CH0>; + interconnect-names = "sdhc-mem"; + }; diff --git a/Documentation/devicetree/bindings/interconnect/qcom,sdm845.txt b/Documentation/devicetree/bindings/interconnect/qcom,sdm845.txt new file mode 100644 index 000000000000..5c4f1d911630 --- /dev/null +++ b/Documentation/devicetree/bindings/interconnect/qcom,sdm845.txt @@ -0,0 +1,24 @@ +Qualcomm SDM845 Network-On-Chip interconnect driver binding +----------------------------------------------------------- + +SDM845 interconnect providers support system bandwidth requirements through +RPMh hardware accelerators known as Bus Clock Manager (BCM). The provider is +able to communicate with the BCM through the Resource State Coordinator (RSC) +associated with each execution environment. Provider nodes must reside within +an RPMh device node pertaining to their RSC and each provider maps to a single +RPMh resource. + +Required properties : +- compatible : shall contain only one of the following: + "qcom,sdm845-rsc-hlos" +- #interconnect-cells : should contain 1 + +Examples: + +apps_rsc: rsc { + rsc_hlos: interconnect { + compatible = "qcom,sdm845-rsc-hlos"; + #interconnect-cells = <1>; + }; +}; + diff --git a/Documentation/devicetree/bindings/interrupt-controller/fsl,irqsteer.txt b/Documentation/devicetree/bindings/interrupt-controller/fsl,irqsteer.txt index 45790ce6f5b9..582991c426ee 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/fsl,irqsteer.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/fsl,irqsteer.txt @@ -6,8 +6,9 @@ Required properties: - "fsl,imx8m-irqsteer" - "fsl,imx-irqsteer" - reg: Physical base address and size of registers. -- interrupts: Should contain the parent interrupt line used to multiplex the - input interrupts. +- interrupts: Should contain the up to 8 parent interrupt lines used to + multiplex the input interrupts. They should be specified sequentially + from output 0 to 7. - clocks: Should contain one clock for entry in clock-names see Documentation/devicetree/bindings/clock/clock-bindings.txt - clock-names: @@ -16,8 +17,8 @@ Required properties: - #interrupt-cells: Specifies the number of cells needed to encode an interrupt source. The value must be 1. - fsl,channel: The output channel that all input IRQs should be steered into. -- fsl,irq-groups: Number of IRQ groups managed by this controller instance. - Each group manages 64 input interrupts. +- fsl,num-irqs: Number of input interrupts of this channel. + Should be multiple of 32 input interrupts and up to 512 interrupts. Example: @@ -28,7 +29,7 @@ Example: clocks = <&clk IMX8MQ_CLK_DISP_APB_ROOT>; clock-names = "ipg"; fsl,channel = <0>; - fsl,irq-groups = <1>; + fsl,num-irqs = <64>; interrupt-controller; #interrupt-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/loongson,ls1x-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/loongson,ls1x-intc.txt new file mode 100644 index 000000000000..a63ed9fcb535 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/loongson,ls1x-intc.txt @@ -0,0 +1,24 @@ +Loongson ls1x Interrupt Controller + +Required properties: + +- compatible : should be "loongson,ls1x-intc". Valid strings are: + +- reg : Specifies base physical address and size of the registers. +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value shall be 2. +- interrupts : Specifies the CPU interrupt the controller is connected to. + +Example: + +intc: interrupt-controller@1fd01040 { + compatible = "loongson,ls1x-intc"; + reg = <0x1fd01040 0x18>; + + interrupt-controller; + #interrupt-cells = <2>; + + interrupt-parent = <&cpu_intc>; + interrupts = <2>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt index 33a98eb44949..c5d589108a94 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt @@ -9,6 +9,7 @@ Required properties: "mediatek,mt8135-sysirq", "mediatek,mt6577-sysirq": for MT8135 "mediatek,mt8127-sysirq", "mediatek,mt6577-sysirq": for MT8127 "mediatek,mt7622-sysirq", "mediatek,mt6577-sysirq": for MT7622 + "mediatek,mt7623-sysirq", "mediatek,mt6577-sysirq": for MT7623 "mediatek,mt6795-sysirq", "mediatek,mt6577-sysirq": for MT6795 "mediatek,mt6797-sysirq", "mediatek,mt6577-sysirq": for MT6797 "mediatek,mt6765-sysirq", "mediatek,mt6577-sysirq": for MT6765 diff --git a/Documentation/devicetree/bindings/leds/common.txt b/Documentation/devicetree/bindings/leds/common.txt index aa1399814a2a..70876ac11367 100644 --- a/Documentation/devicetree/bindings/leds/common.txt +++ b/Documentation/devicetree/bindings/leds/common.txt @@ -37,6 +37,18 @@ Optional properties for child nodes: "ide-disk" - LED indicates IDE disk activity (deprecated), in new implementations use "disk-activity" "timer" - LED flashes at a fixed, configurable rate + "pattern" - LED alters the brightness for the specified duration with one + software timer (requires "led-pattern" property) + +- led-pattern : Array of integers with default pattern for certain triggers. + Each trigger may parse this property differently: + - one-shot : two numbers specifying delay on and delay off (in ms), + - timer : two numbers specifying delay on and delay off (in ms), + - pattern : the pattern is given by a series of tuples, of + brightness and duration (in ms). The exact format is + described in: + Documentation/devicetree/bindings/leds/leds-trigger-pattern.txt + - led-max-microamp : Maximum LED supply current in microamperes. This property can be made mandatory for the board configurations diff --git a/Documentation/devicetree/bindings/leds/leds-trigger-pattern.txt b/Documentation/devicetree/bindings/leds/leds-trigger-pattern.txt new file mode 100644 index 000000000000..d3696680bfc8 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-trigger-pattern.txt @@ -0,0 +1,49 @@ +* Pattern format for LED pattern trigger + +The pattern is given by a series of tuples, of brightness and duration (ms). +The LED is expected to traverse the series and each brightness value for the +specified duration. Duration of 0 means brightness should immediately change to +new value, and writing malformed pattern deactivates any active one. + +1. For gradual dimming, the dimming interval now is set as 50 milliseconds. So +the tuple with duration less than dimming interval (50ms) is treated as a step +change of brightness, i.e. the subsequent brightness will be applied without +adding intervening dimming intervals. + +The gradual dimming format of the software pattern values should be: +"brightness_1 duration_1 brightness_2 duration_2 brightness_3 duration_3 ...". +For example (using sysfs interface): + +echo 0 1000 255 2000 > pattern + +It will make the LED go gradually from zero-intensity to max (255) intensity in +1000 milliseconds, then back to zero intensity in 2000 milliseconds: + +LED brightness + ^ +255-| / \ / \ / + | / \ / \ / + | / \ / \ / + | / \ / \ / + 0-| / \/ \/ + +---0----1----2----3----4----5----6------------> time (s) + +2. To make the LED go instantly from one brightness value to another, we should +use zero-time lengths (the brightness must be same as the previous tuple's). So +the format should be: "brightness_1 duration_1 brightness_1 0 brightness_2 +duration_2 brightness_2 0 ...". +For example (using sysfs interface): + +echo 0 1000 0 0 255 2000 255 0 > pattern + +It will make the LED stay off for one second, then stay at max brightness for +two seconds: + +LED brightness + ^ +255-| +---------+ +---------+ + | | | | | + | | | | | + | | | | | + 0-| -----+ +----+ +---- + +---0----1----2----3----4----5----6------------> time (s) diff --git a/Documentation/devicetree/bindings/media/i2c/adv748x.txt b/Documentation/devicetree/bindings/media/i2c/adv748x.txt index 5dddc95f9cc4..4f91686e54a6 100644 --- a/Documentation/devicetree/bindings/media/i2c/adv748x.txt +++ b/Documentation/devicetree/bindings/media/i2c/adv748x.txt @@ -48,7 +48,16 @@ are numbered as follows. TXA source 10 TXB source 11 -The digital output port nodes must contain at least one endpoint. +The digital output port nodes, when present, shall contain at least one +endpoint. Each of those endpoints shall contain the data-lanes property as +described in video-interfaces.txt. + +Required source endpoint properties: + - data-lanes: an array of physical data lane indexes + The accepted value(s) for this property depends on which of the two + sources are described. For TXA 1, 2 or 4 data lanes can be described + while for TXB only 1 data lane is valid. See video-interfaces.txt + for detailed description. Ports are optional if they are not connected to anything at the hardware level. diff --git a/Documentation/devicetree/bindings/media/i2c/melexis,mlx90640.txt b/Documentation/devicetree/bindings/media/i2c/melexis,mlx90640.txt new file mode 100644 index 000000000000..060d2b7a5893 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/melexis,mlx90640.txt @@ -0,0 +1,20 @@ +* Melexis MLX90640 FIR Sensor + +Melexis MLX90640 FIR sensor support which allows recording of thermal data +with 32x24 resolution excluding 2 lines of coefficient data that is used by +userspace to render processed frames. + +Required Properties: + - compatible : Must be "melexis,mlx90640" + - reg : i2c address of the device + +Example: + + i2c0@1c22000 { + ... + mlx90640@33 { + compatible = "melexis,mlx90640"; + reg = <0x33>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/media/i2c/mt9m001.txt b/Documentation/devicetree/bindings/media/i2c/mt9m001.txt new file mode 100644 index 000000000000..c920552b03ef --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/mt9m001.txt @@ -0,0 +1,38 @@ +MT9M001: 1/2-Inch Megapixel Digital Image Sensor + +The MT9M001 is an SXGA-format with a 1/2-inch CMOS active-pixel digital +image sensor. It is programmable through I2C interface. + +Required Properties: + +- compatible: shall be "onnn,mt9m001". +- clocks: reference to the master clock into sensor + +Optional Properties: + +- reset-gpios: GPIO handle which is connected to the reset pin of the chip. + Active low. +- standby-gpios: GPIO handle which is connected to the standby pin of the chip. + Active high. + +The device node must contain one 'port' child node with one 'endpoint' child +sub-node for its digital output video port, in accordance with the video +interface bindings defined in: +Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + + &i2c1 { + camera-sensor@5d { + compatible = "onnn,mt9m001"; + reg = <0x5d>; + reset-gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; + standby-gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>; + clocks = <&camera_clk>; + port { + mt9m001_out: endpoint { + remote-endpoint = <&vcap_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ov5645.txt b/Documentation/devicetree/bindings/media/i2c/ov5645.txt index fd7aec9f8e24..72ad992f77be 100644 --- a/Documentation/devicetree/bindings/media/i2c/ov5645.txt +++ b/Documentation/devicetree/bindings/media/i2c/ov5645.txt @@ -26,9 +26,9 @@ Example: &i2c1 { ... - ov5645: ov5645@78 { + ov5645: ov5645@3c { compatible = "ovti,ov5645"; - reg = <0x78>; + reg = <0x3c>; enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; reset-gpios = <&gpio5 20 GPIO_ACTIVE_LOW>; @@ -37,7 +37,7 @@ Example: clocks = <&clks 200>; clock-names = "xclk"; - clock-frequency = <23880000>; + clock-frequency = <24000000>; vdddo-supply = <&camera_dovdd_1v8>; vdda-supply = <&camera_avdd_2v8>; diff --git a/Documentation/devicetree/bindings/media/imx7-csi.txt b/Documentation/devicetree/bindings/media/imx7-csi.txt new file mode 100644 index 000000000000..3c07bc676bc3 --- /dev/null +++ b/Documentation/devicetree/bindings/media/imx7-csi.txt @@ -0,0 +1,45 @@ +Freescale i.MX7 CMOS Sensor Interface +===================================== + +csi node +-------- + +This is device node for the CMOS Sensor Interface (CSI) which enables the chip +to connect directly to external CMOS image sensors. + +Required properties: + +- compatible : "fsl,imx7-csi"; +- reg : base address and length of the register set for the device; +- interrupts : should contain CSI interrupt; +- clocks : list of clock specifiers, see + Documentation/devicetree/bindings/clock/clock-bindings.txt for details; +- clock-names : must contain "axi", "mclk" and "dcic" entries, matching + entries in the clock property; + +The device node shall contain one 'port' child node with one child 'endpoint' +node, according to the bindings defined in: +Documentation/devicetree/bindings/media/video-interfaces.txt. + +In the following example a remote endpoint is a video multiplexer. + +example: + + csi: csi@30710000 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "fsl,imx7-csi"; + reg = <0x30710000 0x10000>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_CLK_DUMMY>, + <&clks IMX7D_CSI_MCLK_ROOT_CLK>, + <&clks IMX7D_CLK_DUMMY>; + clock-names = "axi", "mclk", "dcic"; + + port { + csi_from_csi_mux: endpoint { + remote-endpoint = <&csi_mux_to_csi>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt b/Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt new file mode 100644 index 000000000000..71fd74ed3ec8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt @@ -0,0 +1,90 @@ +Freescale i.MX7 Mipi CSI2 +========================= + +mipi_csi2 node +-------------- + +This is the device node for the MIPI CSI-2 receiver core in i.MX7 SoC. It is +compatible with previous version of Samsung D-phy. + +Required properties: + +- compatible : "fsl,imx7-mipi-csi2"; +- reg : base address and length of the register set for the device; +- interrupts : should contain MIPI CSIS interrupt; +- clocks : list of clock specifiers, see + Documentation/devicetree/bindings/clock/clock-bindings.txt for details; +- clock-names : must contain "pclk", "wrap" and "phy" entries, matching + entries in the clock property; +- power-domains : a phandle to the power domain, see + Documentation/devicetree/bindings/power/power_domain.txt for details. +- reset-names : should include following entry "mrst"; +- resets : a list of phandle, should contain reset entry of + reset-names; +- phy-supply : from the generic phy bindings, a phandle to a regulator that + provides power to MIPI CSIS core; + +Optional properties: + +- clock-frequency : The IP's main (system bus) clock frequency in Hz, default + value when this property is not specified is 166 MHz; +- fsl,csis-hs-settle : differential receiver (HS-RX) settle time; + +The device node should contain two 'port' child nodes with one child 'endpoint' +node, according to the bindings defined in: + Documentation/devicetree/bindings/ media/video-interfaces.txt. + The following are properties specific to those nodes. + +port node +--------- + +- reg : (required) can take the values 0 or 1, where 0 shall be + related to the sink port and port 1 shall be the source + one; + +endpoint node +------------- + +- data-lanes : (required) an array specifying active physical MIPI-CSI2 + data input lanes and their mapping to logical lanes; this + shall only be applied to port 0 (sink port), the array's + content is unused only its length is meaningful, + in this case the maximum length supported is 2; + +example: + + mipi_csi: mipi-csi@30750000 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "fsl,imx7-mipi-csi2"; + reg = <0x30750000 0x10000>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_IPG_ROOT_CLK>, + <&clks IMX7D_MIPI_CSI_ROOT_CLK>, + <&clks IMX7D_MIPI_DPHY_ROOT_CLK>; + clock-names = "pclk", "wrap", "phy"; + clock-frequency = <166000000>; + power-domains = <&pgc_mipi_phy>; + phy-supply = <®_1p0d>; + resets = <&src IMX7_RESET_MIPI_PHY_MRST>; + reset-names = "mrst"; + fsl,csis-hs-settle = <3>; + + port@0 { + reg = <0>; + + mipi_from_sensor: endpoint { + remote-endpoint = <&ov2680_to_mipi>; + data-lanes = <1>; + }; + }; + + port@1 { + reg = <1>; + + mipi_vc0_to_csi_mux: endpoint { + remote-endpoint = <&csi_mux_from_mipi_vc0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek-vcodec.txt b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt index 2a615d84a682..b6b5dde6abd8 100644 --- a/Documentation/devicetree/bindings/media/mediatek-vcodec.txt +++ b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt @@ -66,6 +66,15 @@ vcodec_dec: vcodec@16000000 { "vencpll", "venc_lt_sel", "vdec_bus_clk_src"; + assigned-clocks = <&topckgen CLK_TOP_VENC_LT_SEL>, + <&topckgen CLK_TOP_CCI400_SEL>, + <&topckgen CLK_TOP_VDEC_SEL>, + <&apmixedsys CLK_APMIXED_VCODECPLL>, + <&apmixedsys CLK_APMIXED_VENCPLL>; + assigned-clock-parents = <&topckgen CLK_TOP_VCODECPLL_370P5>, + <&topckgen CLK_TOP_UNIVPLL_D2>, + <&topckgen CLK_TOP_VCODECPLL>; + assigned-clock-rates = <0>, <0>, <0>, <1482000000>, <800000000>; }; vcodec_enc: vcodec@18002000 { @@ -105,4 +114,8 @@ vcodec_dec: vcodec@16000000 { "venc_sel", "venc_lt_sel_src", "venc_lt_sel"; + assigned-clocks = <&topckgen CLK_TOP_VENC_SEL>, + <&topckgen CLK_TOP_VENC_LT_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_VENCPLL_D2>, + <&topckgen CLK_TOP_UNIVPLL1_D2>; }; diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt index 0dd84a183ca7..224a4615b418 100644 --- a/Documentation/devicetree/bindings/media/rcar_vin.txt +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt @@ -7,12 +7,13 @@ family of devices. Each VIN instance has a single parallel input that supports RGB and YUV video, with both external synchronization and BT.656 synchronization for the latter. Depending on the instance the VIN input is connected to external SoC pins, or -on Gen3 platforms to a CSI-2 receiver. +on Gen3 and RZ/G2 platforms to a CSI-2 receiver. - compatible: Must be one or more of the following - "renesas,vin-r8a7743" for the R8A7743 device - "renesas,vin-r8a7744" for the R8A7744 device - "renesas,vin-r8a7745" for the R8A7745 device + - "renesas,vin-r8a774c0" for the R8A774C0 device - "renesas,vin-r8a7778" for the R8A7778 device - "renesas,vin-r8a7779" for the R8A7779 device - "renesas,vin-r8a7790" for the R8A7790 device @@ -61,10 +62,10 @@ The per-board settings Gen2 platforms: - data-enable-active: polarity of CLKENB signal, see [1] for description. Default is active high. -The per-board settings Gen3 platforms: +The per-board settings Gen3 and RZ/G2 platforms: -Gen3 platforms can support both a single connected parallel input source -from external SoC pins (port@0) and/or multiple parallel input sources +Gen3 and RZ/G2 platforms can support both a single connected parallel input +source from external SoC pins (port@0) and/or multiple parallel input sources from local SoC CSI-2 receivers (port@1) depending on SoC. - renesas,id - ID number of the VIN, VINx in the documentation. diff --git a/Documentation/devicetree/bindings/media/renesas,fcp.txt b/Documentation/devicetree/bindings/media/renesas,fcp.txt index 3ec91803ba58..79c37395b396 100644 --- a/Documentation/devicetree/bindings/media/renesas,fcp.txt +++ b/Documentation/devicetree/bindings/media/renesas,fcp.txt @@ -2,8 +2,9 @@ Renesas R-Car Frame Compression Processor (FCP) ----------------------------------------------- The FCP is a companion module of video processing modules in the Renesas R-Car -Gen3 SoCs. It provides data compression and decompression, data caching, and -conversion of AXI transactions in order to reduce the memory bandwidth. +Gen3 and RZ/G2 SoCs. It provides data compression and decompression, data +caching, and conversion of AXI transactions in order to reduce the memory +bandwidth. There are three types of FCP: FCP for Codec (FCPC), FCP for VSP (FCPV) and FCP for FDP (FCPF). Their configuration and behaviour depend on the module they diff --git a/Documentation/devicetree/bindings/media/renesas,rcar-csi2.txt b/Documentation/devicetree/bindings/media/renesas,rcar-csi2.txt index 541d936b62e8..d63275e17afd 100644 --- a/Documentation/devicetree/bindings/media/renesas,rcar-csi2.txt +++ b/Documentation/devicetree/bindings/media/renesas,rcar-csi2.txt @@ -2,12 +2,13 @@ Renesas R-Car MIPI CSI-2 ------------------------ The R-Car CSI-2 receiver device provides MIPI CSI-2 capabilities for the -Renesas R-Car family of devices. It is used in conjunction with the +Renesas R-Car and RZ/G2 family of devices. It is used in conjunction with the R-Car VIN module, which provides the video capture capabilities. Mandatory properties -------------------- - compatible: Must be one or more of the following + - "renesas,r8a774c0-csi2" for the R8A774C0 device. - "renesas,r8a7795-csi2" for the R8A7795 device. - "renesas,r8a7796-csi2" for the R8A7796 device. - "renesas,r8a77965-csi2" for the R8A77965 device. diff --git a/Documentation/devicetree/bindings/media/renesas,vsp1.txt b/Documentation/devicetree/bindings/media/renesas,vsp1.txt index 16427017cb45..cd5a955b2ea0 100644 --- a/Documentation/devicetree/bindings/media/renesas,vsp1.txt +++ b/Documentation/devicetree/bindings/media/renesas,vsp1.txt @@ -2,13 +2,13 @@ The VSP is a video processing engine that supports up-/down-scaling, alpha blending, color space conversion and various other image processing features. -It can be found in the Renesas R-Car second generation SoCs. +It can be found in the Renesas R-Car Gen2, R-Car Gen3, RZ/G1, and RZ/G2 SoCs. Required properties: - compatible: Must contain one of the following values - - "renesas,vsp1" for the R-Car Gen2 VSP1 - - "renesas,vsp2" for the R-Car Gen3 VSP2 + - "renesas,vsp1" for the R-Car Gen2 and RZ/G1 VSP1 + - "renesas,vsp2" for the R-Car Gen3 and RZ/G2 VSP2 - reg: Base address and length of the registers block for the VSP. - interrupts: VSP interrupt specifier. diff --git a/Documentation/devicetree/bindings/media/si470x.txt b/Documentation/devicetree/bindings/media/si470x.txt new file mode 100644 index 000000000000..a9403558362e --- /dev/null +++ b/Documentation/devicetree/bindings/media/si470x.txt @@ -0,0 +1,26 @@ +* Silicon Labs FM Radio receiver + +The Silicon Labs Si470x is family of FM radio receivers with receive power scan +supporting 76-108 MHz, programmable through an I2C interface. +Some of them includes an RDS encoder. + +Required Properties: +- compatible: Should contain "silabs,si470x" +- reg: the I2C address of the device + +Optional Properties: +- interrupts : The interrupt number +- reset-gpios: GPIO specifier for the chips reset line + +Example: + +&i2c2 { + si470x@63 { + compatible = "silabs,si470x"; + reg = <0x63>; + + interrupt-parent = <&gpj2>; + interrupts = <4 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpj2 5 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/media/sun6i-csi.txt b/Documentation/devicetree/bindings/media/sun6i-csi.txt index d4ab34f2240c..0dd540bb03db 100644 --- a/Documentation/devicetree/bindings/media/sun6i-csi.txt +++ b/Documentation/devicetree/bindings/media/sun6i-csi.txt @@ -6,8 +6,9 @@ Allwinner V3s SoC features a CSI module(CSI1) with parallel interface. Required properties: - compatible: value must be one of: * "allwinner,sun6i-a31-csi" - * "allwinner,sun8i-h3-csi", "allwinner,sun6i-a31-csi" + * "allwinner,sun8i-h3-csi" * "allwinner,sun8i-v3s-csi" + * "allwinner,sun50i-a64-csi" - reg: base address and size of the memory-mapped region. - interrupts: interrupt associated to this IP - clocks: phandles to the clocks feeding the CSI diff --git a/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt b/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt index 34dd89087cff..86446074e206 100644 --- a/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt +++ b/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt @@ -135,6 +135,8 @@ Required properties: - clocks: contains a phandle to the syscon node describing the clocks. There should then be one cell representing the clock to use +Optional properties: + - memory-region: A phandle to a reserved_memory region to be used for the LPC to AHB mapping diff --git a/Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt b/Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt new file mode 100644 index 000000000000..004b0158cf4d --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt @@ -0,0 +1,68 @@ +Cirrus Logic Lochnagar Audio Development Board + +Lochnagar is an evaluation and development board for Cirrus Logic +Smart CODEC and Amp devices. It allows the connection of most Cirrus +Logic devices on mini-cards, as well as allowing connection of +various application processor systems to provide a full evaluation +platform. Audio system topology, clocking and power can all be +controlled through the Lochnagar, allowing the device under test +to be used in a variety of possible use cases. + +Also see these documents for generic binding information: + [1] GPIO : ../gpio/gpio.txt + +And these for relevant defines: + [2] include/dt-bindings/pinctrl/lochnagar.h + [3] include/dt-bindings/clock/lochnagar.h + +And these documents for the required sub-node binding details: + [4] Clock: ../clock/cirrus,lochnagar.txt + [5] Pinctrl: ../pinctrl/cirrus,lochnagar.txt + [6] Regulator: ../regulator/cirrus,lochnagar.txt + +Required properties: + + - compatible : One of the following strings: + "cirrus,lochnagar1" + "cirrus,lochnagar2" + + - reg : I2C slave address + + - reset-gpios : Reset line to the Lochnagar, see [1]. + +Required sub-nodes: + + - lochnagar-clk : Binding for the clocking components, see [4]. + + - lochnagar-pinctrl : Binding for the pin control components, see [5]. + +Optional sub-nodes: + + - Bindings for the regulator components, see [6]. Only available on + Lochnagar 2. + +Optional properties: + + - present-gpios : Host present line, indicating the presence of a + host system, see [1]. This can be omitted if the present line is + tied in hardware. + +Example: + +lochnagar: lochnagar@22 { + compatible = "cirrus,lochnagar2"; + reg = <0x22>; + + reset-gpios = <&gpio0 55 0>; + present-gpios = <&gpio0 60 0>; + + lochnagar-clk { + compatible = "cirrus,lochnagar2-clk"; + ... + }; + + lochnagar-pinctrl { + compatible = "cirrus,lochnagar-pinctrl"; + ... + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt index a4b056761eaa..d5f68ac78d15 100644 --- a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt +++ b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt @@ -23,6 +23,20 @@ Required properties: Optional properties: - clock-output-names : Should contain name for output clock. +- rohm,reset-snvs-powered : Transfer BD718x7 to SNVS state at reset. + +The BD718x7 supports two different HW states as reset target states. States +are called as SNVS and READY. At READY state all the PMIC power outputs go +down and OTP is reload. At the SNVS state all other logic and external +devices apart from the SNVS power domain are shut off. Please refer to NXP +i.MX8 documentation for further information regarding SNVS state. When a +reset is done via SNVS state the PMIC OTP data is not reload. This causes +power outputs that have been under SW control to stay down when reset has +switched power state to SNVS. If reset is done via READY state the power +outputs will be returned to HW control by OTP loading. Thus the reset +target state is set to READY by default. If SNVS state is used the boot +crucial regulators must have the regulator-always-on and regulator-boot-on +properties set in regulator node. Example: @@ -43,6 +57,7 @@ Example: #clock-cells = <0>; clocks = <&osc 0>; clock-output-names = "bd71837-32k-out"; + rohm,reset-snvs-powered; regulators { buck1: BUCK1 { @@ -50,8 +65,10 @@ Example: regulator-min-microvolt = <700000>; regulator-max-microvolt = <1300000>; regulator-boot-on; + regulator-always-on; regulator-ramp-delay = <1250>; }; + // [...] }; }; diff --git a/Documentation/devicetree/bindings/mfd/st,stpmic1.txt b/Documentation/devicetree/bindings/mfd/st,stpmic1.txt new file mode 100644 index 000000000000..afd45c089585 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/st,stpmic1.txt @@ -0,0 +1,61 @@ +* STMicroelectronics STPMIC1 Power Management IC + +Required properties: +- compatible: : "st,stpmic1" +- reg: : The I2C slave address for the STPMIC1 chip. +- interrupts: : The interrupt line the device is connected to. +- #interrupt-cells: : Should be 1. +- interrupt-controller: : Marks the device node as an interrupt controller. + Interrupt numbers are defined at + dt-bindings/mfd/st,stpmic1.h. + +STPMIC1 consists in a varied group of sub-devices. +Each sub-device binding is be described in own documentation file. + +Device Description +------ ------------ +st,stpmic1-onkey : Power on key, see ../input/st,stpmic1-onkey.txt +st,stpmic1-regulators : Regulators, see ../regulator/st,stpmic1-regulator.txt +st,stpmic1-wdt : Watchdog, see ../watchdog/st,stpmic1-wdt.txt + +Example: + +#include <dt-bindings/mfd/st,stpmic1.h> + +pmic: pmic@33 { + compatible = "st,stpmic1"; + reg = <0x33>; + interrupt-parent = <&gpioa>; + interrupts = <0 2>; + + interrupt-controller; + #interrupt-cells = <2>; + + onkey { + compatible = "st,stpmic1-onkey"; + interrupts = <IT_PONKEY_F 0>,<IT_PONKEY_R 1>; + interrupt-names = "onkey-falling", "onkey-rising"; + power-off-time-sec = <10>; + }; + + watchdog { + compatible = "st,stpmic1-wdt"; + }; + + regulators { + compatible = "st,stpmic1-regulators"; + + vdd_core: buck1 { + regulator-name = "vdd_core"; + regulator-boot-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1200000>; + }; + vdd: buck3 { + regulator-name = "vdd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-pull-down; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt index c797c05cd3c2..d4408a417193 100644 --- a/Documentation/devicetree/bindings/mfd/stmpe.txt +++ b/Documentation/devicetree/bindings/mfd/stmpe.txt @@ -4,15 +4,29 @@ STMPE is an MFD device which may expose the following inbuilt devices: gpio, keypad, touchscreen, adc, pwm, rotator. Required properties: - - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]" - - reg : I2C/SPI address of the device + - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]" + - reg : I2C/SPI address of the device Optional properties: - - interrupts : The interrupt outputs from the controller - - interrupt-controller : Marks the device node as an interrupt controller - - wakeup-source : Marks the input device as wakable - - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024 - - irq-gpio : If present, which GPIO to use for event IRQ + - interrupts : The interrupt outputs from the controller + - interrupt-controller : Marks the device node as an interrupt controller + - wakeup-source : Marks the input device as wakable + - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024 + - irq-gpio : If present, which GPIO to use for event IRQ + +Optional properties for devices with touch and ADC (STMPE811|STMPE610): + - st,sample-time : ADC conversion time in number of clock. + 0 -> 36 clocks 4 -> 80 clocks (recommended) + 1 -> 44 clocks 5 -> 96 clocks + 2 -> 56 clocks 6 -> 124 clocks + 3 -> 64 clocks + - st,mod-12b : ADC Bit mode + 0 -> 10bit ADC 1 -> 12bit ADC + - st,ref-sel : ADC reference source + 0 -> internal 1 -> external + - st,adc-freq : ADC Clock speed + 0 -> 1.625 MHz 2 || 3 -> 6.5 MHz + 1 -> 3.25 MHz Example: diff --git a/Documentation/devicetree/bindings/mips/lantiq/rcu-gphy.txt b/Documentation/devicetree/bindings/mips/lantiq/rcu-gphy.txt deleted file mode 100644 index a0c19bd1ce66..000000000000 --- a/Documentation/devicetree/bindings/mips/lantiq/rcu-gphy.txt +++ /dev/null @@ -1,36 +0,0 @@ -Lantiq XWAY SoC GPHY binding -============================ - -This binding describes a software-defined ethernet PHY, provided by the RCU -module on newer Lantiq XWAY SoCs (xRX200 and newer). - -------------------------------------------------------------------------------- -Required properties: -- compatible : Should be one of - "lantiq,xrx200a1x-gphy" - "lantiq,xrx200a2x-gphy" - "lantiq,xrx300-gphy" - "lantiq,xrx330-gphy" -- reg : Addrress of the GPHY FW load address register -- resets : Must reference the RCU GPHY reset bit -- reset-names : One entry, value must be "gphy" or optional "gphy2" -- clocks : A reference to the (PMU) GPHY clock gate - -Optional properties: -- lantiq,gphy-mode : GPHY_MODE_GE (default) or GPHY_MODE_FE as defined in - <dt-bindings/mips/lantiq_xway_gphy.h> - - -------------------------------------------------------------------------------- -Example for the GPHys on the xRX200 SoCs: - -#include <dt-bindings/mips/lantiq_rcu_gphy.h> - gphy0: gphy@20 { - compatible = "lantiq,xrx200a2x-gphy"; - reg = <0x20 0x4>; - - resets = <&reset0 31 30>, <&reset1 7 7>; - reset-names = "gphy", "gphy2"; - clocks = <&pmu0 XRX200_PMU_GATE_GPHY>; - lantiq,gphy-mode = <GPHY_MODE_GE>; - }; diff --git a/Documentation/devicetree/bindings/mips/lantiq/rcu.txt b/Documentation/devicetree/bindings/mips/lantiq/rcu.txt index 7f0822b4beae..58d51f480c9e 100644 --- a/Documentation/devicetree/bindings/mips/lantiq/rcu.txt +++ b/Documentation/devicetree/bindings/mips/lantiq/rcu.txt @@ -26,24 +26,6 @@ Example of the RCU bindings on a xRX200 SoC: ranges = <0x0 0x203000 0x100>; big-endian; - gphy0: gphy@20 { - compatible = "lantiq,xrx200a2x-gphy"; - reg = <0x20 0x4>; - - resets = <&reset0 31 30>, <&reset1 7 7>; - reset-names = "gphy", "gphy2"; - lantiq,gphy-mode = <GPHY_MODE_GE>; - }; - - gphy1: gphy@68 { - compatible = "lantiq,xrx200a2x-gphy"; - reg = <0x68 0x4>; - - resets = <&reset0 29 28>, <&reset1 6 6>; - reset-names = "gphy", "gphy2"; - lantiq,gphy-mode = <GPHY_MODE_GE>; - }; - reset0: reset-controller@10 { compatible = "lantiq,xrx200-reset"; reg = <0x10 4>, <0x14 4>; diff --git a/Documentation/devicetree/bindings/misc/qcom,fastrpc.txt b/Documentation/devicetree/bindings/misc/qcom,fastrpc.txt new file mode 100644 index 000000000000..2a1827ab50d2 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/qcom,fastrpc.txt @@ -0,0 +1,78 @@ +Qualcomm Technologies, Inc. FastRPC Driver + +The FastRPC implements an IPC (Inter-Processor Communication) +mechanism that allows for clients to transparently make remote method +invocations across DSP and APPS boundaries. This enables developers +to offload tasks to the DSP and free up the application processor for +other tasks. + +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be "qcom,fastrpc" + +- label + Usage: required + Value type: <string> + Definition: should specify the dsp domain name this fastrpc + corresponds to. must be one of this: "adsp", "mdsp", "sdsp", "cdsp" + +- #address-cells + Usage: required + Value type: <u32> + Definition: Must be 1 + +- #size-cells + Usage: required + Value type: <u32> + Definition: Must be 0 + += COMPUTE BANKS +Each subnode of the Fastrpc represents compute context banks available +on the dsp. +- All Compute context banks MUST contain the following properties: + +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be "qcom,fastrpc-compute-cb" + +- reg + Usage: required + Value type: <u32> + Definition: Context Bank ID. + +- qcom,nsessions: + Usage: Optional + Value type: <u32> + Defination: A value indicating how many sessions can share this + context bank. Defaults to 1 when this property + is not specified. + +Example: + +adsp-pil { + compatible = "qcom,msm8996-adsp-pil"; + ... + smd-edge { + label = "lpass"; + fastrpc { + compatible = "qcom,fastrpc"; + qcom,smd-channels = "fastrpcsmd-apps-dsp"; + label = "adsp"; + #address-cells = <1>; + #size-cells = <0>; + + cb@1 { + compatible = "qcom,fastrpc-compute-cb"; + reg = <1>; + }; + + cb@2 { + compatible = "qcom,fastrpc-compute-cb"; + reg = <2>; + }; + ... + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt index 9201a7d8d7b0..540c65ed9cba 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -15,6 +15,7 @@ Required properties: "fsl,imx6q-usdhc" "fsl,imx6sl-usdhc" "fsl,imx6sx-usdhc" + "fsl,imx6ull-usdhc" "fsl,imx7d-usdhc" "fsl,imx8qxp-usdhc" diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index f5a0923b34ca..cdbcfd3a4ff2 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -62,6 +62,8 @@ Optional properties: be referred to mmc-pwrseq-simple.txt. But now it's reused as a tunable delay waiting for I/O signalling and card power supply to be stable, regardless of whether pwrseq-simple is used. Default to 10ms if no available. +- supports-cqe : The presence of this property indicates that the corresponding + MMC host controller supports HW command queue feature. *NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line polarity properties, we have to fix the meaning of the "normal" and "inverted" diff --git a/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt index 32b4b4e41923..2cecdc71d94c 100644 --- a/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt @@ -39,12 +39,16 @@ sdhci@c8000200 { bus-width = <8>; }; -Optional properties for Tegra210 and Tegra186: +Optional properties for Tegra210, Tegra186 and Tegra194: - pinctrl-names, pinctrl-0, pinctrl-1 : Specify pad voltage configurations. Valid pinctrl-names are "sdmmc-3v3" and "sdmmc-1v8" for controllers supporting multiple voltage levels. The order of names should correspond to the pin configuration states in pinctrl-0 and pinctrl-1. +- pinctrl-names : "sdmmc-3v3-drv" and "sdmmc-1v8-drv" are applicable for + Tegra210 where pad config registers are in the pinmux register domain + for pull-up-strength and pull-down-strength values configuration when + using pads at 3V3 and 1V8 levels. - nvidia,only-1-8-v : The presence of this property indicates that the controller operates at a 1.8 V fixed I/O voltage. - nvidia,pad-autocal-pull-up-offset-3v3, diff --git a/Documentation/devicetree/bindings/mmc/ti-omap.txt b/Documentation/devicetree/bindings/mmc/ti-omap.txt index 8de579969763..02fd31cf361d 100644 --- a/Documentation/devicetree/bindings/mmc/ti-omap.txt +++ b/Documentation/devicetree/bindings/mmc/ti-omap.txt @@ -24,31 +24,3 @@ Examples: dmas = <&sdma 61 &sdma 62>; dma-names = "tx", "rx"; }; - -* TI MMC host controller for OMAP1 and 2420 - -The MMC Host Controller on TI OMAP1 and 2420 family provides -an interface for MMC, SD, and SDIO types of memory cards. - -This file documents differences between the core properties described -by mmc.txt and the properties used by the omap mmc driver. - -Note that this driver will not work with omap2430 or later omaps, -please see the omap hsmmc driver for the current omaps. - -Required properties: -- compatible: Must be "ti,omap2420-mmc", for OMAP2420 controllers -- ti,hwmods: For 2420, must be "msdi<n>", where n is controller - instance starting 1 - -Examples: - - msdi1: mmc@4809c000 { - compatible = "ti,omap2420-mmc"; - ti,hwmods = "msdi1"; - reg = <0x4809c000 0x80>; - interrupts = <83>; - dmas = <&sdma 61 &sdma 62>; - dma-names = "tx", "rx"; - }; - diff --git a/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt b/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt new file mode 100644 index 000000000000..3983c11e062c --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt @@ -0,0 +1,60 @@ +Amlogic NAND Flash Controller (NFC) for GXBB/GXL/AXG family SoCs + +This file documents the properties in addition to those available in +the MTD NAND bindings. + +Required properties: +- compatible : contains one of: + - "amlogic,meson-gxl-nfc" + - "amlogic,meson-axg-nfc" +- clocks : + A list of phandle + clock-specifier pairs for the clocks listed + in clock-names. + +- clock-names: Should contain the following: + "core" - NFC module gate clock + "device" - device clock from eMMC sub clock controller + "rx" - rx clock phase + "tx" - tx clock phase + +- amlogic,mmc-syscon : Required for NAND clocks, it's shared with SD/eMMC + controller port C + +Optional children nodes: +Children nodes represent the available nand chips. + +Other properties: +see Documentation/devicetree/bindings/mtd/nand.txt for generic bindings. + +Example demonstrate on AXG SoC: + + sd_emmc_c_clkc: mmc@7000 { + compatible = "amlogic,meson-axg-mmc-clkc", "syscon"; + reg = <0x0 0x7000 0x0 0x800>; + }; + + nand-controller@7800 { + compatible = "amlogic,meson-axg-nfc"; + reg = <0x0 0x7800 0x0 0x100>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>; + + clocks = <&clkc CLKID_SD_EMMC_C>, + <&sd_emmc_c_clkc CLKID_MMC_DIV>, + <&sd_emmc_c_clkc CLKID_MMC_PHASE_RX>, + <&sd_emmc_c_clkc CLKID_MMC_PHASE_TX>; + clock-names = "core", "device", "rx", "tx"; + amlogic,mmc-syscon = <&sd_emmc_c_clkc>; + + pinctrl-names = "default"; + pinctrl-0 = <&nand_pins>; + + nand@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + + nand-on-flash-bbt; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt index bb2075df9b38..4345c3a6f530 100644 --- a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt +++ b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt @@ -4,6 +4,7 @@ Required properties: - compatible : should be one of the following: Generic default - "cdns,qspi-nor". For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor". + For TI AM654 SoC - "ti,am654-ospi", "cdns,qspi-nor". - reg : Contains two entries, each of which is a tuple consisting of a physical address and length. The first entry is the address and length of the controller register set. The second entry is the diff --git a/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt b/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt index 56d3668e2c50..a12e3b5c495d 100644 --- a/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt +++ b/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt @@ -1,4 +1,4 @@ -* Serial NOR flash controller for MTK MT81xx (and similar) +* Serial NOR flash controller for MediaTek SoCs Required properties: - compatible: For mt8173, compatible should be "mediatek,mt8173-nor", @@ -10,6 +10,7 @@ Required properties: "mediatek,mt2712-nor", "mediatek,mt8173-nor" "mediatek,mt7622-nor", "mediatek,mt8173-nor" "mediatek,mt7623-nor", "mediatek,mt8173-nor" + "mediatek,mt7629-nor", "mediatek,mt8173-nor" "mediatek,mt8173-nor" - reg: physical base address and length of the controller's register - clocks: the phandle of the clocks needed by the nor controller diff --git a/Documentation/devicetree/bindings/mtd/stm32-fmc2-nand.txt b/Documentation/devicetree/bindings/mtd/stm32-fmc2-nand.txt new file mode 100644 index 000000000000..ad2bef826582 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/stm32-fmc2-nand.txt @@ -0,0 +1,61 @@ +STMicroelectronics Flexible Memory Controller 2 (FMC2) +NAND Interface + +Required properties: +- compatible: Should be one of: + * st,stm32mp15-fmc2 +- reg: NAND flash controller memory areas. + First region contains the register location. + Regions 2 to 4 respectively contain the data, command, + and address space for CS0. + Regions 5 to 7 contain the same areas for CS1. +- interrupts: The interrupt number +- pinctrl-0: Standard Pinctrl phandle (see: pinctrl/pinctrl-bindings.txt) +- clocks: The clock needed by the NAND flash controller + +Optional properties: +- resets: Reference to a reset controller asserting the FMC controller +- dmas: DMA specifiers (see: dma/stm32-mdma.txt) +- dma-names: Must be "tx", "rx" and "ecc" + +* NAND device bindings: + +Required properties: +- reg: describes the CS lines assigned to the NAND device. + +Optional properties: +- nand-on-flash-bbt: see nand.txt +- nand-ecc-strength: see nand.txt +- nand-ecc-step-size: see nand.txt + +The following ECC strength and step size are currently supported: + - nand-ecc-strength = <1>, nand-ecc-step-size = <512> (Hamming) + - nand-ecc-strength = <4>, nand-ecc-step-size = <512> (BCH4) + - nand-ecc-strength = <8>, nand-ecc-step-size = <512> (BCH8) (default) + +Example: + + fmc: nand-controller@58002000 { + compatible = "st,stm32mp15-fmc2"; + reg = <0x58002000 0x1000>, + <0x80000000 0x1000>, + <0x88010000 0x1000>, + <0x88020000 0x1000>, + <0x81000000 0x1000>, + <0x89010000 0x1000>, + <0x89020000 0x1000>; + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc FMC_K>; + resets = <&rcc FMC_R>; + pinctrl-names = "default"; + pinctrl-0 = <&fmc_pins_a>; + #address-cells = <1>; + #size-cells = <0>; + + nand@0 { + reg = <0>; + nand-on-flash-bbt; + #address-cells = <1>; + #size-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/btusb.txt b/Documentation/devicetree/bindings/net/btusb.txt index 37d67926dd6d..b1ad6ee68e90 100644 --- a/Documentation/devicetree/bindings/net/btusb.txt +++ b/Documentation/devicetree/bindings/net/btusb.txt @@ -9,6 +9,9 @@ Required properties: (more may be added later) are: "usb1286,204e" (Marvell 8997) + "usbcf3,e300" (Qualcomm QCA6174A) + "usb4ca,301a" (Qualcomm QCA6174A (Lite-On)) + Also, vendors that use btusb may have device additional properties, e.g: Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt diff --git a/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt b/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt index 764c0c79b43d..5d76f991c027 100644 --- a/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt +++ b/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt @@ -1,4 +1,4 @@ -TI CPSW Phy mode Selection Device Tree Bindings +TI CPSW Phy mode Selection Device Tree Bindings (DEPRECATED) ----------------------------------------------- Required properties: diff --git a/Documentation/devicetree/bindings/net/dsa/ksz.txt b/Documentation/devicetree/bindings/net/dsa/ksz.txt index 0f407fb371ce..e7db7268fd0f 100644 --- a/Documentation/devicetree/bindings/net/dsa/ksz.txt +++ b/Documentation/devicetree/bindings/net/dsa/ksz.txt @@ -7,6 +7,11 @@ Required properties: of the following: - "microchip,ksz9477" - "microchip,ksz9897" + - "microchip,ksz9896" + - "microchip,ksz9567" + - "microchip,ksz8565" + - "microchip,ksz9893" + - "microchip,ksz9563" Optional properties: @@ -19,58 +24,96 @@ Examples: Ethernet switch connected via SPI to the host, CPU port wired to eth0: - eth0: ethernet@10001000 { - fixed-link { - speed = <1000>; - full-duplex; - }; - }; + eth0: ethernet@10001000 { + fixed-link { + speed = <1000>; + full-duplex; + }; + }; - spi1: spi@f8008000 { - pinctrl-0 = <&pinctrl_spi_ksz>; - cs-gpios = <&pioC 25 0>; - id = <1>; + spi1: spi@f8008000 { + pinctrl-0 = <&pinctrl_spi_ksz>; + cs-gpios = <&pioC 25 0>; + id = <1>; - ksz9477: ksz9477@0 { - compatible = "microchip,ksz9477"; - reg = <0>; + ksz9477: ksz9477@0 { + compatible = "microchip,ksz9477"; + reg = <0>; - spi-max-frequency = <44000000>; - spi-cpha; - spi-cpol; + spi-max-frequency = <44000000>; + spi-cpha; + spi-cpol; - ports { - #address-cells = <1>; - #size-cells = <0>; - port@0 { - reg = <0>; - label = "lan1"; - }; - port@1 { - reg = <1>; - label = "lan2"; - }; - port@2 { - reg = <2>; - label = "lan3"; - }; - port@3 { - reg = <3>; - label = "lan4"; - }; - port@4 { - reg = <4>; - label = "lan5"; - }; - port@5 { - reg = <5>; - label = "cpu"; - ethernet = <ð0>; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - }; - }; + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan1"; + }; + port@1 { + reg = <1>; + label = "lan2"; + }; + port@2 { + reg = <2>; + label = "lan3"; + }; + port@3 { + reg = <3>; + label = "lan4"; + }; + port@4 { + reg = <4>; + label = "lan5"; + }; + port@5 { + reg = <5>; + label = "cpu"; + ethernet = <ð0>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + ksz8565: ksz8565@0 { + compatible = "microchip,ksz8565"; + reg = <0>; + + spi-max-frequency = <44000000>; + spi-cpha; + spi-cpol; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan1"; + }; + port@1 { + reg = <1>; + label = "lan2"; + }; + port@2 { + reg = <2>; + label = "lan3"; + }; + port@3 { + reg = <3>; + label = "lan4"; + }; + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <ð0>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/mt7530.txt b/Documentation/devicetree/bindings/net/dsa/mt7530.txt index aa3527f71fdc..47aa205ee0bd 100644 --- a/Documentation/devicetree/bindings/net/dsa/mt7530.txt +++ b/Documentation/devicetree/bindings/net/dsa/mt7530.txt @@ -3,12 +3,16 @@ Mediatek MT7530 Ethernet switch Required properties: -- compatible: Must be compatible = "mediatek,mt7530"; +- compatible: may be compatible = "mediatek,mt7530" + or compatible = "mediatek,mt7621" - #address-cells: Must be 1. - #size-cells: Must be 0. - mediatek,mcm: Boolean; if defined, indicates that either MT7530 is the part on multi-chip module belong to MT7623A has or the remotely standalone chip as the function MT7623N reference board provided for. + +If compatible mediatek,mt7530 is set then the following properties are required + - core-supply: Phandle to the regulator node necessary for the core power. - io-supply: Phandle to the regulator node necessary for the I/O power. See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt diff --git a/Documentation/devicetree/bindings/net/fsl-enetc.txt b/Documentation/devicetree/bindings/net/fsl-enetc.txt new file mode 100644 index 000000000000..c812e25ae90f --- /dev/null +++ b/Documentation/devicetree/bindings/net/fsl-enetc.txt @@ -0,0 +1,69 @@ +* ENETC ethernet device tree bindings + +Depending on board design and ENETC port type (internal or +external) there are two supported link modes specified by +below device tree bindings. + +Required properties: + +- reg : Specifies PCIe Device Number and Function + Number of the ENETC endpoint device, according + to parent node bindings. +- compatible : Should be "fsl,enetc". + +1) The ENETC external port is connected to a MDIO configurable phy: + +In this case, the ENETC node should include a "mdio" sub-node +that in turn should contain the "ethernet-phy" node describing the +external phy. Below properties are required, their bindings +already defined in ethernet.txt or phy.txt, under +Documentation/devicetree/bindings/net/*. + +Required: + +- phy-handle : Phandle to a PHY on the MDIO bus. + Defined in ethernet.txt. + +- phy-connection-type : Defined in ethernet.txt. + +- mdio : "mdio" node, defined in mdio.txt. + +- ethernet-phy : "ethernet-phy" node, defined in phy.txt. + +Example: + + ethernet@0,0 { + compatible = "fsl,enetc"; + reg = <0x000000 0 0 0 0>; + phy-handle = <&sgmii_phy0>; + phy-connection-type = "sgmii"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + sgmii_phy0: ethernet-phy@2 { + reg = <0x2>; + }; + }; + }; + +2) The ENETC port is an internal port or has a fixed-link external +connection: + +In this case, the ENETC port node defines a fixed link connection, +as specified by "fixed-link.txt", under +Documentation/devicetree/bindings/net/*. + +Required: + +- fixed-link : "fixed-link" node, defined in "fixed-link.txt". + +Example: + ethernet@0,2 { + compatible = "fsl,enetc"; + reg = <0x000200 0 0 0 0>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index 3e17ac1d5d58..174f292d8a3e 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -3,8 +3,8 @@ Required properties: - compatible: Should be "cdns,[<chip>-]{macb|gem}" Use "cdns,at91rm9200-emac" Atmel at91rm9200 SoC. - Use "cdns,at91sam9260-macb" for Atmel at91sam9 SoCs or the 10/100Mbit IP - available on sama5d3 SoCs. + Use "cdns,at91sam9260-macb" for Atmel at91sam9 SoCs. + Use "cdns,sam9x60-macb" for Microchip sam9x60 SoC. Use "cdns,np4-macb" for NP4 SoC devices. Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb". Use "cdns,pc302-gem" for Picochip picoXcell pc302 and later devices based on diff --git a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt index bedcfd5a52cd..691f886cfc4a 100644 --- a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt +++ b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt @@ -19,7 +19,7 @@ Optional properties: "marvell,armada-370-neta" and 9800B for others. - clock-names: List of names corresponding to clocks property; shall be "core" for core clock and "bus" for the optional bus clock. - +- phys: comphy for the ethernet port, see ../phy/phy-bindings.txt Optional properties (valid only for Armada XP/38x): diff --git a/Documentation/devicetree/bindings/net/mdio-mux-multiplexer.txt b/Documentation/devicetree/bindings/net/mdio-mux-multiplexer.txt new file mode 100644 index 000000000000..534e38058fe0 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mdio-mux-multiplexer.txt @@ -0,0 +1,82 @@ +Properties for an MDIO bus multiplexer consumer device + +This is a special case of MDIO mux when MDIO mux is defined as a consumer +of a mux producer device. The mux producer can be of any type like mmio mux +producer, gpio mux producer or generic register based mux producer. + +Required properties in addition to the MDIO Bus multiplexer properties: + +- compatible : should be "mmio-mux-multiplexer" +- mux-controls : mux controller node to use for operating the mux +- mdio-parent-bus : phandle to the parent MDIO bus. + +each child node of mdio bus multiplexer consumer device represent a mdio +bus. + +for more information please refer +Documentation/devicetree/bindings/mux/mux-controller.txt +and Documentation/devicetree/bindings/net/mdio-mux.txt + +Example: +In below example the Mux producer and consumer are separate nodes. + +&i2c0 { + fpga@66 { // fpga connected to i2c + compatible = "fsl,lx2160aqds-fpga", "fsl,fpga-qixis-i2c", + "simple-mfd"; + reg = <0x66>; + + mux: mux-controller { // Mux Producer + compatible = "reg-mux"; + #mux-control-cells = <1>; + mux-reg-masks = <0x54 0xf8>, /* 0: reg 0x54, bits 7:3 */ + <0x54 0x07>; /* 1: reg 0x54, bits 2:0 */ + }; + }; +}; + +mdio-mux-1 { // Mux consumer + compatible = "mdio-mux-multiplexer"; + mux-controls = <&mux 0>; + mdio-parent-bus = <&emdio1>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + mdio@8 { + reg = <0x8>; + #address-cells = <1>; + #size-cells = <0>; + }; + + .. + .. +}; + +mdio-mux-2 { // Mux consumer + compatible = "mdio-mux-multiplexer"; + mux-controls = <&mux 1>; + mdio-parent-bus = <&emdio2>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + mdio@1 { + reg = <0x1>; + #address-cells = <1>; + #size-cells = <0>; + }; + + .. + .. +}; diff --git a/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt b/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt index 14ceb2a5b4e8..41a7dcc80f5b 100644 --- a/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt +++ b/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt @@ -33,3 +33,67 @@ Example: clock-names = "ref"; }; }; + +MediaTek UART based Bluetooth Devices +================================== + +This device is a serial attached device to UART device and thus it must be a +child node of the serial node with UART. + +Please refer to the following documents for generic properties: + + Documentation/devicetree/bindings/serial/slave-device.txt + +Required properties: + +- compatible: Must be + "mediatek,mt7663u-bluetooth": for MT7663U device + "mediatek,mt7668u-bluetooth": for MT7668U device +- vcc-supply: Main voltage regulator +- pinctrl-names: Should be "default", "runtime" +- pinctrl-0: Should contain UART RXD low when the device is powered up to + enter proper bootstrap mode. +- pinctrl-1: Should contain UART mode pin ctrl + +Optional properties: + +- reset-gpios: GPIO used to reset the device whose initial state keeps low, + if the GPIO is missing, then board-level design should be + guaranteed. +- current-speed: Current baud rate of the device whose defaults to 921600 + +Example: + + uart1_pins_boot: uart1-default { + pins-dat { + pinmux = <MT7623_PIN_81_URXD1_FUNC_GPIO81>; + output-low; + }; + }; + + uart1_pins_runtime: uart1-runtime { + pins-dat { + pinmux = <MT7623_PIN_81_URXD1_FUNC_URXD1>, + <MT7623_PIN_82_UTXD1_FUNC_UTXD1>; + }; + }; + + uart1: serial@11003000 { + compatible = "mediatek,mt7623-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11003000 0 0x400>; + interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_UART1_SEL>, + <&pericfg CLK_PERI_UART1>; + clock-names = "baud", "bus"; + + bluetooth { + compatible = "mediatek,mt7663u-bluetooth"; + vcc-supply = <®_5v>; + reset-gpios = <&pio 24 GPIO_ACTIVE_LOW>; + pinctrl-names = "default", "runtime"; + pinctrl-0 = <&uart1_pins_boot>; + pinctrl-1 = <&uart1_pins_runtime>; + current-speed = <921600>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/nixge.txt b/Documentation/devicetree/bindings/net/nixge.txt index e55af7f0881a..85d7240a9b20 100644 --- a/Documentation/devicetree/bindings/net/nixge.txt +++ b/Documentation/devicetree/bindings/net/nixge.txt @@ -1,17 +1,53 @@ * NI XGE Ethernet controller Required properties: -- compatible: Should be "ni,xge-enet-2.00" -- reg: Address and length of the register set for the device +- compatible: Should be "ni,xge-enet-3.00", but can be "ni,xge-enet-2.00" for + older device trees with DMA engines co-located in the address map, + with the one reg entry to describe the whole device. +- reg: Address and length of the register set for the device. It contains the + information of registers in the same order as described by reg-names. +- reg-names: Should contain the reg names + "dma": DMA engine control and status region + "ctrl": MDIO and PHY control and status region - interrupts: Should contain tx and rx interrupt - interrupt-names: Should be "rx" and "tx" - phy-mode: See ethernet.txt file in the same directory. -- phy-handle: See ethernet.txt file in the same directory. - nvmem-cells: Phandle of nvmem cell containing the MAC address - nvmem-cell-names: Should be "address" +Optional properties: +- mdio subnode to indicate presence of MDIO controller +- fixed-link : Assume a fixed link. See fixed-link.txt in the same directory. + Use instead of phy-handle. +- phy-handle: See ethernet.txt file in the same directory. + Examples (10G generic PHY): nixge0: ethernet@40000000 { + compatible = "ni,xge-enet-3.00"; + reg = <0x40000000 0x4000 + 0x41002000 0x2000>; + reg-names = "dma", "ctrl"; + + nvmem-cells = <ð1_addr>; + nvmem-cell-names = "address"; + + interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>, <0 30 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "rx", "tx"; + interrupt-parent = <&intc>; + + phy-mode = "xgmii"; + phy-handle = <ðernet_phy1>; + + mdio { + ethernet_phy1: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <4>; + }; + }; + }; + +Examples (10G generic PHY, no MDIO): + nixge0: ethernet@40000000 { compatible = "ni,xge-enet-2.00"; reg = <0x40000000 0x6000>; @@ -24,9 +60,33 @@ Examples (10G generic PHY): phy-mode = "xgmii"; phy-handle = <ðernet_phy1>; + }; + +Examples (1G generic fixed-link + MDIO): + nixge0: ethernet@40000000 { + compatible = "ni,xge-enet-2.00"; + reg = <0x40000000 0x6000>; - ethernet_phy1: ethernet-phy@4 { - compatible = "ethernet-phy-ieee802.3-c45"; - reg = <4>; + nvmem-cells = <ð1_addr>; + nvmem-cell-names = "address"; + + interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>, <0 30 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "rx", "tx"; + interrupt-parent = <&intc>; + + phy-mode = "xgmii"; + + fixed-link { + speed = <1000>; + pause; + link-gpios = <&gpio0 63 GPIO_ACTIVE_HIGH>; + }; + + mdio { + ethernet_phy1: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <4>; + }; }; + }; diff --git a/Documentation/devicetree/bindings/net/qcom,ethqos.txt b/Documentation/devicetree/bindings/net/qcom,ethqos.txt new file mode 100644 index 000000000000..fcf5035810b5 --- /dev/null +++ b/Documentation/devicetree/bindings/net/qcom,ethqos.txt @@ -0,0 +1,64 @@ +Qualcomm Ethernet ETHQOS device + +This documents dwmmac based ethernet device which supports Gigabit +ethernet for version v2.3.0 onwards. + +This device has following properties: + +Required properties: + +- compatible: Should be qcom,qcs404-ethqos" + +- reg: Address and length of the register set for the device + +- reg-names: Should contain register names "stmmaceth", "rgmii" + +- clocks: Should contain phandle to clocks + +- clock-names: Should contain clock names "stmmaceth", "pclk", + "ptp_ref", "rgmii" + +- interrupts: Should contain phandle to interrupts + +- interrupt-names: Should contain interrupt names "macirq", "eth_lpi" + +Rest of the properties are defined in stmmac.txt file in same directory + + +Example: + +ethernet: ethernet@7a80000 { + compatible = "qcom,qcs404-ethqos"; + reg = <0x07a80000 0x10000>, + <0x07a96000 0x100>; + reg-names = "stmmaceth", "rgmii"; + clock-names = "stmmaceth", "pclk", "ptp_ref", "rgmii"; + clocks = <&gcc GCC_ETH_AXI_CLK>, + <&gcc GCC_ETH_SLAVE_AHB_CLK>, + <&gcc GCC_ETH_PTP_CLK>, + <&gcc GCC_ETH_RGMII_CLK>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq", "eth_lpi"; + snps,reset-gpio = <&tlmm 60 GPIO_ACTIVE_LOW>; + snps,reset-active-low; + + snps,txpbl = <8>; + snps,rxpbl = <2>; + snps,aal; + snps,tso; + + phy-handle = <&phy1>; + phy-mode = "rgmii"; + + mdio { + #address-cells = <0x1>; + #size-cells = <0x0>; + compatible = "snps,dwmac-mdio"; + phy1: phy@4 { + device_type = "ethernet-phy"; + reg = <0x4>; + }; + }; + +}; diff --git a/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt index 0c17a0ec9b7b..7b9a776230c0 100644 --- a/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt +++ b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt @@ -4,6 +4,13 @@ This node provides properties for configuring the MediaTek mt76xx wireless device. The node is expected to be specified as a child node of the PCI controller to which the wireless chip is connected. +Alternatively, it can specify the wireless part of the MT7628/MT7688 SoC. +For SoC, use the compatible string "mediatek,mt7628-wmac" and the following +properties: + +- reg: Address and length of the register set for the device. +- interrupts: Main device interrupt + Optional properties: - mac-address: See ethernet.txt in the parent directory @@ -30,3 +37,15 @@ Optional nodes: }; }; }; + +MT7628 example: + +wmac: wmac@10300000 { + compatible = "mediatek,mt7628-wmac"; + reg = <0x10300000 0x100000>; + + interrupt-parent = <&cpuintc>; + interrupts = <6>; + + mediatek,mtd-eeprom = <&factory 0x0000>; +}; diff --git a/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt b/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt index 792bc5fafeb9..7a999a135e56 100644 --- a/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt +++ b/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt @@ -1,7 +1,7 @@ Freescale i.MX6 On-Chip OTP Controller (OCOTP) device tree bindings This binding represents the on-chip eFuse OTP controller found on -i.MX6Q/D, i.MX6DL/S, i.MX6SL, i.MX6SX, i.MX6UL and i.MX6SLL SoCs. +i.MX6Q/D, i.MX6DL/S, i.MX6SL, i.MX6SX, i.MX6UL, i.MX6ULL/ULZ and i.MX6SLL SoCs. Required properties: - compatible: should be one of @@ -9,8 +9,10 @@ Required properties: "fsl,imx6sl-ocotp" (i.MX6SL), or "fsl,imx6sx-ocotp" (i.MX6SX), "fsl,imx6ul-ocotp" (i.MX6UL), + "fsl,imx6ull-ocotp" (i.MX6ULL/ULZ), "fsl,imx7d-ocotp" (i.MX7D/S), "fsl,imx6sll-ocotp" (i.MX6SLL), + "fsl,imx7ulp-ocotp" (i.MX7ULP), followed by "syscon". - #address-cells : Should be 1 - #size-cells : Should be 1 diff --git a/Documentation/devicetree/bindings/nvmem/xlnx,zynqmp-nvmem.txt b/Documentation/devicetree/bindings/nvmem/xlnx,zynqmp-nvmem.txt new file mode 100644 index 000000000000..4881561b3a02 --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/xlnx,zynqmp-nvmem.txt @@ -0,0 +1,46 @@ +-------------------------------------------------------------------------- += Zynq UltraScale+ MPSoC nvmem firmware driver binding = +-------------------------------------------------------------------------- +The nvmem_firmware node provides access to the hardware related data +like soc revision, IDCODE... etc, By using the firmware interface. + +Required properties: +- compatible: should be "xlnx,zynqmp-nvmem-fw" + += Data cells = +Are child nodes of silicon id, bindings of which as described in +bindings/nvmem/nvmem.txt + +------- + Example +------- +firmware { + zynqmp_firmware: zynqmp-firmware { + compatible = "xlnx,zynqmp-firmware"; + method = "smc"; + + nvmem_firmware { + compatible = "xlnx,zynqmp-nvmem-fw"; + #address-cells = <1>; + #size-cells = <1>; + + /* Data cells */ + soc_revision: soc_revision { + reg = <0x0 0x4>; + }; + }; + }; +}; + += Data consumers = +Are device nodes which consume nvmem data cells. + +For example: + pcap { + ... + + nvmem-cells = <&soc_revision>; + nvmem-cell-names = "soc_revision"; + + ... + }; diff --git a/Documentation/devicetree/bindings/opp/opp.txt b/Documentation/devicetree/bindings/opp/opp.txt index c396c4c0af92..76b6c79604a5 100644 --- a/Documentation/devicetree/bindings/opp/opp.txt +++ b/Documentation/devicetree/bindings/opp/opp.txt @@ -129,6 +129,9 @@ Optional properties: - opp-microamp-<name>: Named opp-microamp property. Similar to opp-microvolt-<name> property, but for microamp instead. +- opp-level: A value representing the performance level of the device, + expressed as a 32-bit integer. + - clock-latency-ns: Specifies the maximum possible transition latency (in nanoseconds) for switching to this OPP from any other OPP. diff --git a/Documentation/devicetree/bindings/pci/altera-pcie.txt b/Documentation/devicetree/bindings/pci/altera-pcie.txt index 6c396f17c91a..816b244a221e 100644 --- a/Documentation/devicetree/bindings/pci/altera-pcie.txt +++ b/Documentation/devicetree/bindings/pci/altera-pcie.txt @@ -1,11 +1,13 @@ * Altera PCIe controller Required properties: -- compatible : should contain "altr,pcie-root-port-1.0" +- compatible : should contain "altr,pcie-root-port-1.0" or "altr,pcie-root-port-2.0" - reg: a list of physical base address and length for TXS and CRA. + For "altr,pcie-root-port-2.0", additional HIP base address and length. - reg-names: must include the following entries: "Txs": TX slave port region "Cra": Control register access region + "Hip": Hard IP region (if "altr,pcie-root-port-2.0") - interrupts: specifies the interrupt source of the parent interrupt controller. The format of the interrupt specifier depends on the parent interrupt controller. diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt index d514c1f2365f..a7f5f5afa0e6 100644 --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -9,6 +9,7 @@ Required properties: - "fsl,imx6sx-pcie", - "fsl,imx6qp-pcie" - "fsl,imx7d-pcie" + - "fsl,imx8mq-pcie" - reg: base address and length of the PCIe controller - interrupts: A list of interrupt outputs of the controller. Must contain an entry for each entry in the interrupt-names property. @@ -45,7 +46,7 @@ Additional required properties for imx6sx-pcie: PCIE_PHY power domains - power-domain-names: Must be "pcie", "pcie_phy" -Additional required properties for imx7d-pcie: +Additional required properties for imx7d-pcie and imx8mq-pcie: - power-domains: Must be set to a phandle pointing to PCIE_PHY power domain - resets: Must contain phandles to PCIe-related reset lines exposed by SRC IP block @@ -53,6 +54,11 @@ Additional required properties for imx7d-pcie: - "pciephy" - "apps" - "turnoff" +- fsl,imx7d-pcie-phy: A phandle to an fsl,imx7d-pcie-phy node. + +Additional required properties for imx8mq-pcie: +- clock-names: Must include the following additional entries: + - "pcie_aux" Example: @@ -79,3 +85,13 @@ Example: clocks = <&clks 144>, <&clks 206>, <&clks 189>; clock-names = "pcie", "pcie_bus", "pcie_phy"; }; + +* Freescale i.MX7d PCIe PHY + +This is the PHY associated with the IMX7d PCIe controller. It's used by the +PCI-e controller via the fsl,imx7d-pcie-phy phandle. + +Required properties: +- compatible: + - "fsl,imx7d-pcie-phy" +- reg: base address and length of the PCIe PHY controller diff --git a/Documentation/devicetree/bindings/pci/layerscape-pci.txt b/Documentation/devicetree/bindings/pci/layerscape-pci.txt index 9b2b8d66d1f4..e20ceaab9b38 100644 --- a/Documentation/devicetree/bindings/pci/layerscape-pci.txt +++ b/Documentation/devicetree/bindings/pci/layerscape-pci.txt @@ -13,6 +13,7 @@ information. Required properties: - compatible: should contain the platform identifier such as: + RC mode: "fsl,ls1021a-pcie" "fsl,ls2080a-pcie", "fsl,ls2085a-pcie" "fsl,ls2088a-pcie" @@ -20,6 +21,8 @@ Required properties: "fsl,ls1046a-pcie" "fsl,ls1043a-pcie" "fsl,ls1012a-pcie" + EP mode: + "fsl,ls1046a-pcie-ep", "fsl,ls-pcie-ep" - reg: base addresses and lengths of the PCIe controller register blocks. - interrupts: A list of interrupt outputs of the controller. Must contain an entry for each entry in the interrupt-names property. diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt index 976ef7bfff93..6904882a0e94 100644 --- a/Documentation/devicetree/bindings/pci/rcar-pci.txt +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -3,6 +3,7 @@ Required properties: compatible: "renesas,pcie-r8a7743" for the R8A7743 SoC; "renesas,pcie-r8a7744" for the R8A7744 SoC; + "renesas,pcie-r8a774c0" for the R8A774C0 SoC; "renesas,pcie-r8a7779" for the R8A7779 SoC; "renesas,pcie-r8a7790" for the R8A7790 SoC; "renesas,pcie-r8a7791" for the R8A7791 SoC; @@ -13,7 +14,8 @@ compatible: "renesas,pcie-r8a7743" for the R8A7743 SoC; "renesas,pcie-r8a77990" for the R8A77990 SoC; "renesas,pcie-rcar-gen2" for a generic R-Car Gen2 or RZ/G1 compatible device. - "renesas,pcie-rcar-gen3" for a generic R-Car Gen3 compatible device. + "renesas,pcie-rcar-gen3" for a generic R-Car Gen3 or + RZ/G2 compatible device. When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt index 452fe48c4fdd..d5cbfe6b0d89 100644 --- a/Documentation/devicetree/bindings/pci/ti-pci.txt +++ b/Documentation/devicetree/bindings/pci/ti-pci.txt @@ -1,14 +1,21 @@ TI PCI Controllers PCIe DesignWare Controller - - compatible: Should be "ti,dra7-pcie" for RC - Should be "ti,dra7-pcie-ep" for EP + - compatible: Should be "ti,dra7-pcie" for RC (deprecated) + Should be "ti,dra7-pcie-ep" for EP (deprecated) + Should be "ti,dra746-pcie-rc" for dra74x/dra76 in RC mode + Should be "ti,dra746-pcie-ep" for dra74x/dra76 in EP mode + Should be "ti,dra726-pcie-rc" for dra72x in RC mode + Should be "ti,dra726-pcie-ep" for dra72x in EP mode - phys : list of PHY specifiers (used by generic PHY framework) - phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the number of PHYs as specified in *phys* property. - ti,hwmods : Name of the hwmod associated to the pcie, "pcie<X>", where <X> is the instance number of the pcie from the HW spec. - num-lanes as specified in ../designware-pcie.txt + - ti,syscon-lane-sel : phandle/offset pair. Phandle to the system control + module and the register offset to specify lane + selection. HOST MODE ========= diff --git a/Documentation/devicetree/bindings/phy/cdns,dphy.txt b/Documentation/devicetree/bindings/phy/cdns,dphy.txt new file mode 100644 index 000000000000..1095bc4e72d9 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/cdns,dphy.txt @@ -0,0 +1,20 @@ +Cadence DPHY +============ + +Cadence DPHY block. + +Required properties: +- compatible: should be set to "cdns,dphy". +- reg: physical base address and length of the DPHY registers. +- clocks: DPHY reference clocks. +- clock-names: must contain "psm" and "pll_ref". +- #phy-cells: must be set to 0. + +Example: + dphy0: dphy@fd0e0000{ + compatible = "cdns,dphy"; + reg = <0x0 0xfd0e0000 0x0 0x1000>; + clocks = <&psm_clk>, <&pll_ref_clk>; + clock-names = "psm", "pll_ref"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-armada38x-comphy.txt b/Documentation/devicetree/bindings/phy/phy-armada38x-comphy.txt new file mode 100644 index 000000000000..ad49e5c01334 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-armada38x-comphy.txt @@ -0,0 +1,40 @@ +mvebu armada 38x comphy driver +------------------------------ + +This comphy controller can be found on Marvell Armada 38x. It provides a +number of shared PHYs used by various interfaces (network, sata, usb, +PCIe...). + +Required properties: + +- compatible: should be "marvell,armada-380-comphy" +- reg: should contain the comphy register location and length. +- #address-cells: should be 1. +- #size-cells: should be 0. + +A sub-node is required for each comphy lane provided by the comphy. + +Required properties (child nodes): + +- reg: comphy lane number. +- #phy-cells : from the generic phy bindings, must be 1. Defines the + input port to use for a given comphy lane. + +Example: + + comphy: phy@18300 { + compatible = "marvell,armada-380-comphy"; + reg = <0x18300 0x100>; + #address-cells = <1>; + #size-cells = <0>; + + cpm_comphy0: phy@0 { + reg = <0>; + #phy-cells = <1>; + }; + + cpm_comphy1: phy@1 { + reg = <1>; + #phy-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt b/Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt index bfcf80341657..cf2cd86db267 100644 --- a/Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt +++ b/Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt @@ -1,16 +1,27 @@ -mvebu comphy driver -------------------- +MVEBU comphy drivers +-------------------- -A comphy controller can be found on Marvell Armada 7k/8k on the CP110. It -provides a number of shared PHYs used by various interfaces (network, sata, -usb, PCIe...). +COMPHY controllers can be found on the following Marvell MVEBU SoCs: +* Armada 7k/8k (on the CP110) +* Armada 3700 +It provides a number of shared PHYs used by various interfaces (network, SATA, +USB, PCIe...). Required properties: -- compatible: should be "marvell,comphy-cp110" -- reg: should contain the comphy register location and length. -- marvell,system-controller: should contain a phandle to the - system controller node. +- compatible: should be one of: + * "marvell,comphy-cp110" for Armada 7k/8k + * "marvell,comphy-a3700" for Armada 3700 +- reg: should contain the COMPHY register(s) location(s) and length(s). + * 1 entry for Armada 7k/8k + * 4 entries for Armada 3700 along with the corresponding reg-names + properties, memory areas are: + * Generic COMPHY registers + * Lane 1 (PCIe/GbE) + * Lane 0 (USB3/GbE) + * Lane 2 (SATA/USB3) +- marvell,system-controller: should contain a phandle to the system + controller node (only for Armada 7k/8k) - #address-cells: should be 1. - #size-cells: should be 0. @@ -18,11 +29,11 @@ A sub-node is required for each comphy lane provided by the comphy. Required properties (child nodes): -- reg: comphy lane number. -- #phy-cells : from the generic phy bindings, must be 1. Defines the +- reg: COMPHY lane number. +- #phy-cells : from the generic PHY bindings, must be 1. Defines the input port to use for a given comphy lane. -Example: +Examples: cpm_comphy: phy@120000 { compatible = "marvell,comphy-cp110"; @@ -41,3 +52,33 @@ Example: #phy-cells = <1>; }; }; + + comphy: phy@18300 { + compatible = "marvell,comphy-a3700"; + reg = <0x18300 0x300>, + <0x1F000 0x400>, + <0x5C000 0x400>, + <0xe0178 0x8>; + reg-names = "comphy", + "lane1_pcie_gbe", + "lane0_usb3_gbe", + "lane2_sata_usb3"; + #address-cells = <1>; + #size-cells = <0>; + + + comphy0: phy@0 { + reg = <0>; + #phy-cells = <1>; + }; + + comphy1: phy@1 { + reg = <1>; + #phy-cells = <1>; + }; + + comphy2: phy@2 { + reg = <2>; + #phy-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-mvebu-utmi.txt b/Documentation/devicetree/bindings/phy/phy-mvebu-utmi.txt new file mode 100644 index 000000000000..aa99ceec73b0 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-mvebu-utmi.txt @@ -0,0 +1,38 @@ +MVEBU A3700 UTMI PHY +-------------------- + +USB2 UTMI+ PHY controllers can be found on the following Marvell MVEBU SoCs: +* Armada 3700 + +On Armada 3700, there are two USB controllers, one is compatible with the USB2 +and USB3 specifications and supports OTG. The other one is USB2 compliant and +only supports host mode. Both of these controllers come with a slightly +different UTMI PHY. + +Required Properties: + +- compatible: Should be one of: + * "marvell,a3700-utmi-host-phy" for the PHY connected to + the USB2 host-only controller. + * "marvell,a3700-utmi-otg-phy" for the PHY connected to + the USB3 and USB2 OTG capable controller. +- reg: PHY IP register range. +- marvell,usb-misc-reg: handle on the "USB miscellaneous registers" shared + region covering registers related to both the host + controller and the PHY. +- #phy-cells: Standard property (Documentation: phy-bindings.txt) Should be 0. + + +Example: + + usb2_utmi_host_phy: phy@5f000 { + compatible = "marvell,armada-3700-utmi-host-phy"; + reg = <0x5f000 0x800>; + marvell,usb-misc-reg = <&usb2_syscon>; + #phy-cells = <0>; + }; + + usb2_syscon: system-controller@5f800 { + compatible = "marvell,armada-3700-usb2-host-misc", "syscon"; + reg = <0x5f800 0x800>; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt index 074a7b3b0425..00639baae74a 100644 --- a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt @@ -23,6 +23,8 @@ Optional properties: register files". When set driver will request its phandle as one companion-grf for some special SoCs (e.g RV1108). + - extcon : phandle to the extcon device providing the cable state for + the otg phy. Required nodes : a sub-node is required for each port the phy provides. The sub-node name is used to identify host or otg port, diff --git a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt index 41a1074228ba..5d181fc3cc18 100644 --- a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt +++ b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt @@ -9,6 +9,8 @@ Required properties: "qcom,ipq8074-qmp-pcie-phy" for PCIe phy on IPQ8074 "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996, "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996, + "qcom,msm8998-qmp-usb3-phy" for USB3 QMP V3 phy on msm8998, + "qcom,msm8998-qmp-ufs-phy" for UFS QMP phy on msm8998, "qcom,sdm845-qmp-usb3-phy" for USB3 QMP V3 phy on sdm845, "qcom,sdm845-qmp-usb3-uni-phy" for USB3 QMP V3 UNI phy on sdm845, "qcom,sdm845-qmp-ufs-phy" for UFS QMP phy on sdm845. @@ -42,6 +44,10 @@ Required properties: "aux", "cfg_ahb", "ref". For "qcom,msm8996-qmp-usb3-phy" must contain: "aux", "cfg_ahb", "ref". + For "qcom,msm8998-qmp-usb3-phy" must contain: + "aux", "cfg_ahb", "ref". + For "qcom,msm8998-qmp-ufs-phy" must contain: + "ref", "ref_aux". For "qcom,sdm845-qmp-usb3-phy" must contain: "aux", "cfg_ahb", "ref", "com_aux". For "qcom,sdm845-qmp-usb3-uni-phy" must contain: @@ -61,6 +67,9 @@ Required properties: "phy", "common", "cfg". For "qcom,msm8996-qmp-usb3-phy" must contain "phy", "common". + For "qcom,msm8998-qmp-usb3-phy" must contain + "phy", "common". + For "qcom,msm8998-qmp-ufs-phy": no resets are listed. For "qcom,sdm845-qmp-usb3-phy" must contain: "phy", "common". For "qcom,sdm845-qmp-usb3-uni-phy" must contain: diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt index 03025d97998b..fe29f9e0af6d 100644 --- a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt +++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt @@ -6,6 +6,7 @@ QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets. Required properties: - compatible: compatible list, contains "qcom,msm8996-qusb2-phy" for 14nm PHY on msm8996, + "qcom,msm8998-qusb2-phy" for 10nm PHY on msm8998, "qcom,sdm845-qusb2-phy" for 10nm PHY on sdm845. - reg: offset and length of the PHY register set. diff --git a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt index de7b5393c163..ad9c290d8f15 100644 --- a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt +++ b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt @@ -6,6 +6,8 @@ This file provides information on what the device node for the R-Car generation Required properties: - compatible: "renesas,usb2-phy-r8a774a1" if the device is a part of an R8A774A1 SoC. + "renesas,usb2-phy-r8a774c0" if the device is a part of an R8A774C0 + SoC. "renesas,usb2-phy-r8a7795" if the device is a part of an R8A7795 SoC. "renesas,usb2-phy-r8a7796" if the device is a part of an R8A7796 diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt index 57dfda8a7a1d..8f93c3b694a7 100644 --- a/Documentation/devicetree/bindings/phy/ti-phy.txt +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt @@ -35,6 +35,7 @@ Required properties: DRA7x Should be "ti,dra7x-usb2-phy2" for the 2nd instance of USB2 PHY in DRA7x + Should be "ti,am654-usb2" for the USB2 PHYs on AM654. - reg : Address and length of the register set for the device. - #phy-cells: determine the number of cells that should be given in the phandle while referencing this phy. diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt index 759aa1732e48..7f64a7e92c28 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt @@ -19,6 +19,7 @@ PMIC's from Qualcomm. "qcom,pm8998-gpio" "qcom,pma8084-gpio" "qcom,pmi8994-gpio" + "qcom,pmi8998-gpio" "qcom,pms405-gpio" And must contain either "qcom,spmi-gpio" or "qcom,ssbi-gpio" diff --git a/Documentation/devicetree/bindings/power/fsl,imx-gpcv2.txt b/Documentation/devicetree/bindings/power/fsl,imx-gpcv2.txt index 7c947a996df1..7c7e972aaa42 100644 --- a/Documentation/devicetree/bindings/power/fsl,imx-gpcv2.txt +++ b/Documentation/devicetree/bindings/power/fsl,imx-gpcv2.txt @@ -32,6 +32,9 @@ Required properties: Optional properties: - power-supply: Power supply used to power the domain +- clocks: a number of phandles to clocks that need to be enabled during + domain power-up sequencing to ensure reset propagation into devices + located inside this power domain Example: diff --git a/Documentation/devicetree/bindings/power/qcom,rpmpd.txt b/Documentation/devicetree/bindings/power/qcom,rpmpd.txt new file mode 100644 index 000000000000..980e5413d18f --- /dev/null +++ b/Documentation/devicetree/bindings/power/qcom,rpmpd.txt @@ -0,0 +1,145 @@ +Qualcomm RPM/RPMh Power domains + +For RPM/RPMh Power domains, we communicate a performance state to RPM/RPMh +which then translates it into a corresponding voltage on a rail + +Required Properties: + - compatible: Should be one of the following + * qcom,msm8996-rpmpd: RPM Power domain for the msm8996 family of SoC + * qcom,sdm845-rpmhpd: RPMh Power domain for the sdm845 family of SoC + - #power-domain-cells: number of cells in Power domain specifier + must be 1. + - operating-points-v2: Phandle to the OPP table for the Power domain. + Refer to Documentation/devicetree/bindings/power/power_domain.txt + and Documentation/devicetree/bindings/opp/opp.txt for more details + +Refer to <dt-bindings/power/qcom-rpmpd.h> for the level values for +various OPPs for different platforms as well as Power domain indexes + +Example: rpmh power domain controller and OPP table + +#include <dt-bindings/power/qcom-rpmhpd.h> + +opp-level values specified in the OPP tables for RPMh power domains +should use the RPMH_REGULATOR_LEVEL_* constants from +<dt-bindings/power/qcom-rpmhpd.h> + + rpmhpd: power-controller { + compatible = "qcom,sdm845-rpmhpd"; + #power-domain-cells = <1>; + operating-points-v2 = <&rpmhpd_opp_table>; + + rpmhpd_opp_table: opp-table { + compatible = "operating-points-v2"; + + rpmhpd_opp_ret: opp1 { + opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>; + }; + + rpmhpd_opp_min_svs: opp2 { + opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>; + }; + + rpmhpd_opp_low_svs: opp3 { + opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>; + }; + + rpmhpd_opp_svs: opp4 { + opp-level = <RPMH_REGULATOR_LEVEL_SVS>; + }; + + rpmhpd_opp_svs_l1: opp5 { + opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>; + }; + + rpmhpd_opp_nom: opp6 { + opp-level = <RPMH_REGULATOR_LEVEL_NOM>; + }; + + rpmhpd_opp_nom_l1: opp7 { + opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>; + }; + + rpmhpd_opp_nom_l2: opp8 { + opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>; + }; + + rpmhpd_opp_turbo: opp9 { + opp-level = <RPMH_REGULATOR_LEVEL_TURBO>; + }; + + rpmhpd_opp_turbo_l1: opp10 { + opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>; + }; + }; + }; + +Example: rpm power domain controller and OPP table + + rpmpd: power-controller { + compatible = "qcom,msm8996-rpmpd"; + #power-domain-cells = <1>; + operating-points-v2 = <&rpmpd_opp_table>; + + rpmpd_opp_table: opp-table { + compatible = "operating-points-v2"; + + rpmpd_opp_low: opp1 { + opp-level = <1>; + }; + + rpmpd_opp_ret: opp2 { + opp-level = <2>; + }; + + rpmpd_opp_svs: opp3 { + opp-level = <3>; + }; + + rpmpd_opp_normal: opp4 { + opp-level = <4>; + }; + + rpmpd_opp_high: opp5 { + opp-level = <5>; + }; + + rpmpd_opp_turbo: opp6 { + opp-level = <6>; + }; + }; + }; + +Example: Client/Consumer device using OPP table + + leaky-device0@12350000 { + compatible = "foo,i-leak-current"; + reg = <0x12350000 0x1000>; + power-domains = <&rpmhpd SDM845_MX>; + operating-points-v2 = <&leaky_opp_table>; + }; + + + leaky_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp1 { + opp-hz = /bits/ 64 <144000>; + required-opps = <&rpmhpd_opp_low>; + }; + + opp2 { + opp-hz = /bits/ 64 <400000>; + required-opps = <&rpmhpd_opp_ret>; + }; + + opp3 { + opp-hz = /bits/ 64 <20000000>; + required-opps = <&rpmpd_opp_svs>; + }; + + opp4 { + opp-hz = /bits/ 64 <25000000>; + required-opps = <&rpmpd_opp_normal>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.txt b/Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.txt new file mode 100644 index 000000000000..d366f1eb623a --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.txt @@ -0,0 +1,25 @@ +-------------------------------------------------------------------- +Device Tree Bindings for the Xilinx Zynq MPSoC Power Management +-------------------------------------------------------------------- +The zynqmp-power node describes the power management configurations. +It will control remote suspend/shutdown interfaces. + +Required properties: + - compatible: Must contain: "xlnx,zynqmp-power" + - interrupts: Interrupt specifier + +------- +Example +------- + +firmware { + zynqmp_firmware: zynqmp-firmware { + compatible = "xlnx,zynqmp-firmware"; + method = "smc"; + + zynqmp_power: zynqmp-power { + compatible = "xlnx,zynqmp-power"; + interrupts = <0 35 4>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/power/supply/battery.txt b/Documentation/devicetree/bindings/power/supply/battery.txt index 89871ab8c704..5c913d4cf36c 100644 --- a/Documentation/devicetree/bindings/power/supply/battery.txt +++ b/Documentation/devicetree/bindings/power/supply/battery.txt @@ -16,6 +16,7 @@ Required Properties: Optional Properties: - voltage-min-design-microvolt: drained battery voltage + - voltage-max-design-microvolt: fully charged battery voltage - energy-full-design-microwatt-hours: battery design energy - charge-full-design-microamp-hours: battery design capacity - precharge-current-microamp: current for pre-charge phase @@ -48,6 +49,7 @@ Example: bat: battery { compatible = "simple-battery"; voltage-min-design-microvolt = <3200000>; + voltage-max-design-microvolt = <4200000>; energy-full-design-microwatt-hours = <5290000>; charge-full-design-microamp-hours = <1430000>; precharge-current-microamp = <256000>; diff --git a/Documentation/devicetree/bindings/power/supply/sc27xx-fg.txt b/Documentation/devicetree/bindings/power/supply/sc27xx-fg.txt index fc35ac577401..0a5705b8b592 100644 --- a/Documentation/devicetree/bindings/power/supply/sc27xx-fg.txt +++ b/Documentation/devicetree/bindings/power/supply/sc27xx-fg.txt @@ -9,8 +9,8 @@ Required properties: "sprd,sc2731-fgu". - reg: The address offset of fuel gauge unit. - battery-detect-gpios: GPIO for battery detection. -- io-channels: Specify the IIO ADC channel to get temperature. -- io-channel-names: Should be "bat-temp". +- io-channels: Specify the IIO ADC channels to get temperature and charge voltage. +- io-channel-names: Should be "bat-temp" or "charge-vol". - nvmem-cells: A phandle to the calibration cells provided by eFuse device. - nvmem-cell-names: Should be "fgu_calib". - monitored-battery: Phandle of battery characteristics devicetree node. @@ -47,8 +47,8 @@ Example: compatible = "sprd,sc2731-fgu"; reg = <0xa00>; battery-detect-gpios = <&pmic_eic 9 GPIO_ACTIVE_HIGH>; - io-channels = <&pmic_adc 5>; - io-channel-names = "bat-temp"; + io-channels = <&pmic_adc 5>, <&pmic_adc 14>; + io-channel-names = "bat-temp", "charge-vol"; nvmem-cells = <&fgu_calib>; nvmem-cell-names = "fgu_calib"; monitored-battery = <&bat>; diff --git a/Documentation/devicetree/bindings/power/xlnx,zynqmp-genpd.txt b/Documentation/devicetree/bindings/power/xlnx,zynqmp-genpd.txt new file mode 100644 index 000000000000..8d1b8200ebd0 --- /dev/null +++ b/Documentation/devicetree/bindings/power/xlnx,zynqmp-genpd.txt @@ -0,0 +1,34 @@ +----------------------------------------------------------- +Device Tree Bindings for the Xilinx Zynq MPSoC PM domains +----------------------------------------------------------- +The binding for zynqmp-power-controller follow the common +generic PM domain binding[1]. + +[1] Documentation/devicetree/bindings/power/power_domain.txt + +== Zynq MPSoC Generic PM Domain Node == + +Required property: + - Below property should be in zynqmp-firmware node. + - #power-domain-cells: Number of cells in a PM domain specifier. Must be 1. + +Power domain ID indexes are mentioned in +include/dt-bindings/power/xlnx-zynqmp-power.h. + +------- +Example +------- + +firmware { + zynqmp_firmware: zynqmp-firmware { + ... + #power-domain-cells = <1>; + ... + }; +}; + +sata { + ... + power-domains = <&zynqmp_firmware 28>; + ... +}; diff --git a/Documentation/devicetree/bindings/property-units.txt b/Documentation/devicetree/bindings/property-units.txt index 45ce054d844d..bfd33734faca 100644 --- a/Documentation/devicetree/bindings/property-units.txt +++ b/Documentation/devicetree/bindings/property-units.txt @@ -31,6 +31,7 @@ Electricity -microwatt-hours: micro Watt-hours -microvolt : micro volts -picofarads : picofarads +-femtofarads : femtofarads Temperature ---------------------------------------- diff --git a/Documentation/devicetree/bindings/ptp/ptp-qoriq.txt b/Documentation/devicetree/bindings/ptp/ptp-qoriq.txt index c5d0e7998e2b..454c937076a2 100644 --- a/Documentation/devicetree/bindings/ptp/ptp-qoriq.txt +++ b/Documentation/devicetree/bindings/ptp/ptp-qoriq.txt @@ -17,6 +17,11 @@ Clock Properties: - fsl,tmr-fiper1 Fixed interval period pulse generator. - fsl,tmr-fiper2 Fixed interval period pulse generator. - fsl,max-adj Maximum frequency adjustment in parts per billion. + - fsl,extts-fifo The presence of this property indicates hardware + support for the external trigger stamp FIFO. + - little-endian The presence of this property indicates the 1588 timer + IP block is little-endian mode. The default endian mode + is big-endian. These properties set the operational parameters for the PTP clock. You must choose these carefully for the clock to work right. diff --git a/Documentation/devicetree/bindings/regulator/fan53555.txt b/Documentation/devicetree/bindings/regulator/fan53555.txt index 54a3f2c80e3a..e7fc045281d1 100644 --- a/Documentation/devicetree/bindings/regulator/fan53555.txt +++ b/Documentation/devicetree/bindings/regulator/fan53555.txt @@ -1,7 +1,8 @@ Binding for Fairchild FAN53555 regulators Required properties: - - compatible: one of "fcs,fan53555", "silergy,syr827", "silergy,syr828" + - compatible: one of "fcs,fan53555", "fcs,fan53526", "silergy,syr827" or + "silergy,syr828" - reg: I2C address Optional properties: diff --git a/Documentation/devicetree/bindings/regulator/fixed-regulator.txt b/Documentation/devicetree/bindings/regulator/fixed-regulator.txt deleted file mode 100644 index 0c2a6c8a1536..000000000000 --- a/Documentation/devicetree/bindings/regulator/fixed-regulator.txt +++ /dev/null @@ -1,35 +0,0 @@ -Fixed Voltage regulators - -Required properties: -- compatible: Must be "regulator-fixed"; -- regulator-name: Defined in regulator.txt as optional, but required here. - -Optional properties: -- gpio: gpio to use for enable control -- startup-delay-us: startup time in microseconds -- enable-active-high: Polarity of GPIO is Active high -If this property is missing, the default assumed is Active low. -- gpio-open-drain: GPIO is open drain type. - If this property is missing then default assumption is false. --vin-supply: Input supply name. - -Any property defined as part of the core regulator -binding, defined in regulator.txt, can also be used. -However a fixed voltage regulator is expected to have the -regulator-min-microvolt and regulator-max-microvolt -to be the same. - -Example: - - abc: fixedregulator@0 { - compatible = "regulator-fixed"; - regulator-name = "fixed-supply"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - gpio = <&gpio1 16 0>; - startup-delay-us = <70000>; - enable-active-high; - regulator-boot-on; - gpio-open-drain; - vin-supply = <&parent_reg>; - }; diff --git a/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml b/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml new file mode 100644 index 000000000000..d289c2f7455a --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml @@ -0,0 +1,67 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/fixed-regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Fixed Voltage regulators + +maintainers: + - Liam Girdwood <lgirdwood@gmail.com> + - Mark Brown <broonie@kernel.org> + +description: + Any property defined as part of the core regulator binding, defined in + regulator.txt, can also be used. However a fixed voltage regulator is + expected to have the regulator-min-microvolt and regulator-max-microvolt + to be the same. + +properties: + compatible: + const: regulator-fixed + + regulator-name: true + + gpio: + description: gpio to use for enable control + maxItems: 1 + + startup-delay-us: + description: startup time in microseconds + $ref: /schemas/types.yaml#/definitions/uint32 + + enable-active-high: + description: + Polarity of GPIO is Active high. If this property is missing, + the default assumed is Active low. + type: boolean + + gpio-open-drain: + description: + GPIO is open drain type. If this property is missing then default + assumption is false. + type: boolean + + vin-supply: + description: Input supply phandle. + $ref: /schemas/types.yaml#/definitions/phandle + +required: + - compatible + - regulator-name + +examples: + - | + reg_1v8: regulator-1v8 { + compatible = "regulator-fixed"; + regulator-name = "1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio1 16 0>; + startup-delay-us = <70000>; + enable-active-high; + regulator-boot-on; + gpio-open-drain; + vin-supply = <&parent_reg>; + }; +... diff --git a/Documentation/devicetree/bindings/regulator/max77650-regulator.txt b/Documentation/devicetree/bindings/regulator/max77650-regulator.txt new file mode 100644 index 000000000000..f1cbe813c30f --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max77650-regulator.txt @@ -0,0 +1,41 @@ +Regulator driver for MAX77650 PMIC from Maxim Integrated. + +This module is part of the MAX77650 MFD device. For more details +see Documentation/devicetree/bindings/mfd/max77650.txt. + +The regulator controller is represented as a sub-node of the PMIC node +on the device tree. + +The device has a single LDO regulator and a SIMO buck-boost regulator with +three independent power rails. + +Required properties: +-------------------- +- compatible: Must be "maxim,max77650-regulator" + +Each rail must be instantiated under the regulators subnode of the top PMIC +node. Up to four regulators can be defined. For standard regulator properties +refer to Documentation/devicetree/bindings/regulator/regulator.txt. + +Available regulator compatible strings are: "ldo", "sbb0", "sbb1", "sbb2". + +Example: +-------- + + regulators { + compatible = "maxim,max77650-regulator"; + + max77650_ldo: regulator@0 { + regulator-compatible = "ldo"; + regulator-name = "max77650-ldo"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <2937500>; + }; + + max77650_sbb0: regulator@1 { + regulator-compatible = "sbb0"; + regulator-name = "max77650-sbb0"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1587500>; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/pfuze100.txt b/Documentation/devicetree/bindings/regulator/pfuze100.txt index f9be1acf891c..4d3b12b92cb3 100644 --- a/Documentation/devicetree/bindings/regulator/pfuze100.txt +++ b/Documentation/devicetree/bindings/regulator/pfuze100.txt @@ -8,7 +8,7 @@ Optional properties: - fsl,pfuze-support-disable-sw: Boolean, if present disable all unused switch regulators to save power consumption. Attention, ensure that all important regulators (e.g. DDR ref, DDR supply) has set the "regulator-always-on" - property. If not present, the switched regualtors are always on and can't be + property. If not present, the switched regulators are always on and can't be disabled. This binding is a workaround to keep backward compatibility with old dtb's which rely on the fact that the switched regulators are always on and don't mark them explicit as "regulator-always-on". diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd70528-regulator.txt b/Documentation/devicetree/bindings/regulator/rohm,bd70528-regulator.txt new file mode 100644 index 000000000000..698cfc3bc3dd --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/rohm,bd70528-regulator.txt @@ -0,0 +1,68 @@ +ROHM BD70528 Power Management Integrated Circuit regulator bindings + +Required properties: + - regulator-name: should be "buck1", "buck2", "buck3", "ldo1", "ldo2", "ldo3", + "led_ldo1", "led_ldo2" + +List of regulators provided by this controller. BD70528 regulators node +should be sub node of the BD70528 MFD node. See BD70528 MFD bindings at +Documentation/devicetree/bindings/mfd/rohm,bd70528-pmic.txt + +The valid names for BD70528 regulator nodes are: +BUCK1, BUCK2, BUCK3, LDO1, LDO2, LDO3, LED_LDO1, LED_LDO2 + +Optional properties: +- Any optional property defined in bindings/regulator/regulator.txt + +Example: +regulators { + buck1: BUCK1 { + regulator-name = "buck1"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + regulator-ramp-delay = <125>; + }; + buck2: BUCK2 { + regulator-name = "buck2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-ramp-delay = <125>; + }; + buck3: BUCK3 { + regulator-name = "buck3"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-ramp-delay = <250>; + }; + ldo1: LDO1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + ldo2: LDO2 { + regulator-name = "ldo2"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + ldo3: LDO3 { + regulator-name = "ldo3"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <3300000>; + }; + led_ldo1: LED_LDO1 { + regulator-name = "led_ldo1"; + regulator-min-microvolt = <200000>; + regulator-max-microvolt = <300000>; + }; + led_ldo2: LED_LDO2 { + regulator-name = "led_ldo2"; + regulator-min-microvolt = <200000>; + regulator-max-microvolt = <300000>; + }; +}; diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt index 4b98ca26e61a..cbce62c22b60 100644 --- a/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt @@ -27,8 +27,38 @@ BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6 LDO1, LDO2, LDO3, LDO4, LDO5, LDO6 Optional properties: +- rohm,dvs-run-voltage : PMIC default "RUN" state voltage in uV. + See below table for bucks which support this. +- rohm,dvs-idle-voltage : PMIC default "IDLE" state voltage in uV. + See below table for bucks which support this. +- rohm,dvs-suspend-voltage : PMIC default "SUSPEND" state voltage in uV. + See below table for bucks which support this. - Any optional property defined in bindings/regulator/regulator.txt +Supported default DVS states: + +BD71837: +buck | dvs-run-voltage | dvs-idle-voltage | dvs-suspend-voltage +----------------------------------------------------------------------------- +1 | supported | supported | supported +---------------------------------------------------------------------------- +2 | supported | supported | not supported +---------------------------------------------------------------------------- +3 | supported | not supported | not supported +---------------------------------------------------------------------------- +4 | supported | not supported | not supported +---------------------------------------------------------------------------- +rest | not supported | not supported | not supported + +BD71847: +buck | dvs-run-voltage | dvs-idle-voltage | dvs-suspend-voltage +----------------------------------------------------------------------------- +1 | supported | supported | supported +---------------------------------------------------------------------------- +2 | supported | supported | not supported +---------------------------------------------------------------------------- +rest | not supported | not supported | not supported + Example: regulators { buck1: BUCK1 { @@ -36,7 +66,11 @@ regulators { regulator-min-microvolt = <700000>; regulator-max-microvolt = <1300000>; regulator-boot-on; + regulator-always-on; regulator-ramp-delay = <1250>; + rohm,dvs-run-voltage = <900000>; + rohm,dvs-idle-voltage = <850000>; + rohm,dvs-suspend-voltage = <800000>; }; buck2: BUCK2 { regulator-name = "buck2"; @@ -45,18 +79,22 @@ regulators { regulator-boot-on; regulator-always-on; regulator-ramp-delay = <1250>; + rohm,dvs-run-voltage = <1000000>; + rohm,dvs-idle-voltage = <900000>; }; buck3: BUCK3 { regulator-name = "buck3"; regulator-min-microvolt = <700000>; regulator-max-microvolt = <1300000>; regulator-boot-on; + rohm,dvs-run-voltage = <1000000>; }; buck4: BUCK4 { regulator-name = "buck4"; regulator-min-microvolt = <700000>; regulator-max-microvolt = <1300000>; regulator-boot-on; + rohm,dvs-run-voltage = <1000000>; }; buck5: BUCK5 { regulator-name = "buck5"; diff --git a/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt b/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt index a3f476240565..6189df71ea98 100644 --- a/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt @@ -23,16 +23,14 @@ Switches are fixed voltage regulators with only enable/disable capability. Optional properties: - st,mask-reset: mask reset for this regulator: the regulator configuration is maintained during pmic reset. -- regulator-pull-down: enable high pull down - if not specified light pull down is used - regulator-over-current-protection: if set, all regulators are switched off in case of over-current detection on this regulator, if not set, the driver only sends an over-current event. -- interrupt-parent: phandle to the parent interrupt controller - interrupts: index of current limit detection interrupt - <regulator>-supply: phandle to the parent supply/regulator node each regulator supply can be described except vref_ddr. +- regulator-active-discharge: can be used on pwr_sw1 and pwr_sw2. Example: regulators { @@ -43,7 +41,6 @@ regulators { vdd_core: buck1 { regulator-name = "vdd_core"; interrupts = <IT_CURLIM_BUCK1 0>; - interrupt-parent = <&pmic>; st,mask-reset; regulator-pull-down; regulator-min-microvolt = <700000>; @@ -53,7 +50,6 @@ regulators { v3v3: buck4 { regulator-name = "v3v3"; interrupts = <IT_CURLIM_BUCK4 0>; - interrupt-parent = <&mypmic>; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; diff --git a/Documentation/devicetree/bindings/regulator/tps65218.txt b/Documentation/devicetree/bindings/regulator/tps65218.txt index 02f0e9bbfbf8..54aded3b78e2 100644 --- a/Documentation/devicetree/bindings/regulator/tps65218.txt +++ b/Documentation/devicetree/bindings/regulator/tps65218.txt @@ -71,8 +71,13 @@ tps65218: tps65218@24 { regulator-always-on; }; + ls2: regulator-ls2 { + regulator-min-microamp = <100000>; + regulator-max-microamp = <1000000>; + }; + ls3: regulator-ls3 { - regulator-min-microvolt = <100000>; - regulator-max-microvolt = <1000000>; + regulator-min-microamp = <100000>; + regulator-max-microamp = <1000000>; }; }; diff --git a/Documentation/devicetree/bindings/reset/brcm,brcmstb-reset.txt b/Documentation/devicetree/bindings/reset/brcm,brcmstb-reset.txt new file mode 100644 index 000000000000..6e5341b4f891 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/brcm,brcmstb-reset.txt @@ -0,0 +1,27 @@ +Broadcom STB SW_INIT-style reset controller +=========================================== + +Broadcom STB SoCs have a SW_INIT-style reset controller with separate +SET/CLEAR/STATUS registers and possibly multiple banks, each of 32 bit +reset lines. + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: +- compatible: should be brcm,brcmstb-reset +- reg: register base and length +- #reset-cells: must be set to 1 + +Example: + + reset: reset-controller@8404318 { + compatible = "brcm,brcmstb-reset"; + reg = <0x8404318 0x30>; + #reset-cells = <1>; + }; + + ðernet_switch { + resets = <&reset>; + reset-names = "switch"; + }; diff --git a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt index 1ab1d109318e..2ecf33815d18 100644 --- a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt +++ b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt @@ -5,7 +5,9 @@ Please also refer to reset.txt in this directory for common reset controller binding usage. Required properties: -- compatible: Should be "fsl,imx7d-src", "syscon" +- compatible: + - For i.MX7 SoCs should be "fsl,imx7d-src", "syscon" + - For i.MX8MQ SoCs should be "fsl,imx8mq-src", "syscon" - reg: should be register base and length as documented in the datasheet - interrupts: Should contain SRC interrupt @@ -44,4 +46,5 @@ Example: For list of all valid reset indicies see -<dt-bindings/reset/imx7-reset.h> +<dt-bindings/reset/imx7-reset.h> for i.MX7 and +<dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ diff --git a/Documentation/devicetree/bindings/reset/xlnx,zynqmp-reset.txt b/Documentation/devicetree/bindings/reset/xlnx,zynqmp-reset.txt new file mode 100644 index 000000000000..27a45fe5ecf1 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/xlnx,zynqmp-reset.txt @@ -0,0 +1,52 @@ +-------------------------------------------------------------------------- + = Zynq UltraScale+ MPSoC reset driver binding = +-------------------------------------------------------------------------- +The Zynq UltraScale+ MPSoC has several different resets. + +See Chapter 36 of the Zynq UltraScale+ MPSoC TRM (UG) for more information +about zynqmp resets. + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Required Properties: +- compatible: "xlnx,zynqmp-reset" +- #reset-cells: Specifies the number of cells needed to encode reset + line, should be 1 + +------- +Example +------- + +firmware { + zynqmp_firmware: zynqmp-firmware { + compatible = "xlnx,zynqmp-firmware"; + method = "smc"; + + zynqmp_reset: reset-controller { + compatible = "xlnx,zynqmp-reset"; + #reset-cells = <1>; + }; + }; +}; + +Specifying reset lines connected to IP modules +============================================== + +Device nodes that need access to reset lines should +specify them as a reset phandle in their corresponding node as +specified in reset.txt. + +For list of all valid reset indicies see +<dt-bindings/reset/xlnx-zynqmp-resets.h> + +Example: + +serdes: zynqmp_phy@fd400000 { + ... + + resets = <&zynqmp_reset ZYNQMP_RESET_SATA>; + reset-names = "sata_rst"; + + ... +}; diff --git a/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt b/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt index 18b892d010d8..2405e35a1bc0 100644 --- a/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt +++ b/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt @@ -16,6 +16,7 @@ Required properties: "abracon,ab1803" "abracon,ab1804" "abracon,ab1805" + "microcrystal,rv1805" Using "abracon,abx80x" will enable chip autodetection. - "reg": I2C bus address of the device diff --git a/Documentation/devicetree/bindings/rtc/cdns,rtc.txt b/Documentation/devicetree/bindings/rtc/cdns,rtc.txt new file mode 100644 index 000000000000..14a04487b432 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/cdns,rtc.txt @@ -0,0 +1,25 @@ +Cadence Real Time Clock + +The Cadence RTC controller with date, time and alarm capabilities. +The alarm may wake the system from low-power state. + +Required properties: +- compatible: Should be "cdns,rtc-r109v3" +- reg: Specifies base physical address and size of the register area. +- interrupts: A single interrupt specifier. +- clocks: Must contain two entries: + - pclk: APB registers clock + - ref_clk: reference 1Hz or 100Hz clock, depending on IP configuration + See ../clocks/clock-bindings.txt for details. + +Example: + rtc0: rtc@fd080000 { + compatible = "cdns,rtc-r109v3"; + reg = <0xfd080000 0x1000>; + + clock-names = "pclk", "ref_clk"; + clocks = <&sysclock>, <&refclock>; + + interrupt-parent = <&gic>; + interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/rtc/isil,isl1208.txt b/Documentation/devicetree/bindings/rtc/isil,isl1208.txt new file mode 100644 index 000000000000..51f003006f04 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/isil,isl1208.txt @@ -0,0 +1,38 @@ +Intersil ISL1209/19 I2C RTC/Alarm chip with event in + +ISL12X9 have additional pins EVIN and #EVDET for tamper detection, while the +ISL1208 and ISL1218 do not. They are all use the same driver with the bindings +described here, with chip specific properties as noted. + +Required properties supported by the device: + - "compatible": Should be one of the following: + - "isil,isl1208" + - "isil,isl1209" + - "isil,isl1218" + - "isil,isl1219" + - "reg": I2C bus address of the device + +Optional properties: + - "interrupt-names": list which may contains "irq" and "evdet" + evdet applies to isl1209 and isl1219 only + - "interrupts": list of interrupts for "irq" and "evdet" + evdet applies to isl1209 and isl1219 only + - "isil,ev-evienb": Enable or disable internal pull on EVIN pin + Applies to isl1209 and isl1219 only + Possible values are 0 and 1 + Value 0 enables internal pull-up on evin pin, 1 disables it. + Default will leave the non-volatile configuration of the pullup + as is. + +Example isl1219 node with #IRQ pin connected to SoC gpio1 pin12 and #EVDET pin +connected to SoC gpio2 pin 24 and internal pull-up enabled in EVIN pin. + + isl1219: rtc@68 { + compatible = "isil,isl1219"; + reg = <0x68>; + interrupt-names = "irq", "evdet"; + interrupts-extended = <&gpio1 12 IRQ_TYPE_EDGE_FALLING>, + <&gpio2 24 IRQ_TYPE_EDGE_FALLING>; + isil,ev-evienb = <1>; + }; + diff --git a/Documentation/devicetree/bindings/rtc/isil,isl1219.txt b/Documentation/devicetree/bindings/rtc/isil,isl1219.txt deleted file mode 100644 index c3efd48e91c2..000000000000 --- a/Documentation/devicetree/bindings/rtc/isil,isl1219.txt +++ /dev/null @@ -1,29 +0,0 @@ -Intersil ISL1219 I2C RTC/Alarm chip with event in - -ISL1219 has additional pins EVIN and #EVDET for tamper detection. - -Required properties supported by the device: - - - "compatible": must be "isil,isl1219" - - "reg": I2C bus address of the device - -Optional properties: - - - "interrupt-names": list which may contains "irq" and "evdet" - - "interrupts": list of interrupts for "irq" and "evdet" - - "isil,ev-evienb": if present EV.EVIENB bit is set to the specified - value for proper operation. - - -Example isl1219 node with #IRQ pin connected to SoC gpio1 pin12 - and #EVDET pin connected to SoC gpio2 pin 24: - - isl1219: rtc@68 { - compatible = "isil,isl1219"; - reg = <0x68>; - interrupt-names = "irq", "evdet"; - interrupts-extended = <&gpio1 12 IRQ_TYPE_EDGE_FALLING>, - <&gpio2 24 IRQ_TYPE_EDGE_FALLING>; - isil,ev-evienb = <1>; - }; - diff --git a/Documentation/devicetree/bindings/rtc/nxp,pcf85063.txt b/Documentation/devicetree/bindings/rtc/nxp,pcf85063.txt new file mode 100644 index 000000000000..d3e380ad712d --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/nxp,pcf85063.txt @@ -0,0 +1,18 @@ +* NXP PCF85063 Real Time Clock + +Required properties: +- compatible: Should contain "nxp,pcf85063". +- reg: I2C address for chip. + +Optional property: +- quartz-load-femtofarads: The capacitive load of the quartz(x-tal), + expressed in femto Farad (fF). Valid values are 7000 and 12500. + Default value (if no value is specified) is 7000fF. + +Example: + +pcf85063: rtc@51 { + compatible = "nxp,pcf85063"; + reg = <0x51>; + quartz-load-femtofarads = <12500>; +}; diff --git a/Documentation/devicetree/bindings/rtc/nxp,pcf8523.txt b/Documentation/devicetree/bindings/rtc/nxp,pcf8523.txt new file mode 100644 index 000000000000..0b1080c60f63 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/nxp,pcf8523.txt @@ -0,0 +1,18 @@ +* NXP PCF8523 Real Time Clock + +Required properties: +- compatible: Should contain "nxp,pcf8523". +- reg: I2C address for chip. + +Optional property: +- quartz-load-femtofarads: The capacitive load of the quartz(x-tal), + expressed in femto Farad (fF). Valid values are 7000 and 12500. + Default value (if no value is specified) is 12500fF. + +Example: + +pcf8523: rtc@68 { + compatible = "nxp,pcf8523"; + reg = <0x68>; + quartz-load-femtofarads = <7000>; +}; diff --git a/Documentation/devicetree/bindings/rtc/rtc-meson.txt b/Documentation/devicetree/bindings/rtc/rtc-meson.txt new file mode 100644 index 000000000000..e921fe66a362 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/rtc-meson.txt @@ -0,0 +1,35 @@ +* Amlogic Meson6, Meson8, Meson8b and Meson8m2 RTC + +Required properties: +- compatible: should be one of the following describing the hardware: + * "amlogic,meson6-rtc" + * "amlogic,meson8-rtc" + * "amlogic,meson8b-rtc" + * "amlogic,meson8m2-rtc" + +- reg: physical register space for the controller's memory mapped registers. +- interrupts: the interrupt line of the RTC block. +- clocks: reference to the external 32.768kHz crystal oscillator. +- vdd-supply: reference to the power supply of the RTC block. +- resets: reset controller reference to allow reset of the controller + +Optional properties for the battery-backed non-volatile memory: +- #address-cells: should be 1 to address the battery-backed non-volatile memory +- #size-cells: should be 1 to reference the battery-backed non-volatile memory + +Optional child nodes: +- see ../nvmem/nvmem.txt + +Example: + + rtc: rtc@740 { + compatible = "amlogic,meson6-rtc"; + reg = <0x740 0x14>; + interrupts = <GIC_SPI 72 IRQ_TYPE_EDGE_RISING>; + clocks = <&rtc32k_xtal>; + vdd-supply = <&rtc_vdd>; + resets = <&reset RESET_RTC>; + + #address-cells = <1>; + #size-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/rtc/rtc.txt b/Documentation/devicetree/bindings/rtc/rtc.txt index 7c8da6926095..f4687c68c08c 100644 --- a/Documentation/devicetree/bindings/rtc/rtc.txt +++ b/Documentation/devicetree/bindings/rtc/rtc.txt @@ -21,12 +21,16 @@ Optional properties The following properties may not be supported by all drivers. However, if a driver wants to support one of the below features, it should adapt the bindings below. -- trickle-resistor-ohms : Selected resistor for trickle charger. Should be given - if trickle charger should be enabled -- trickle-diode-disable : Do not use internal trickle charger diode Should be - given if internal trickle charger diode should be - disabled -- wakeup-source : Enables wake up of host system on alarm +- trickle-resistor-ohms : Selected resistor for trickle charger. Should be given + if trickle charger should be enabled +- trickle-diode-disable : Do not use internal trickle charger diode Should be + given if internal trickle charger diode should be + disabled +- wakeup-source : Enables wake up of host system on alarm +- quartz-load-femtofarads : The capacitive load of the quartz(x-tal), + expressed in femto Farad (fF). + The default value shall be listed (if optional), + and likewise all valid values. Trivial RTCs ------------ @@ -39,21 +43,23 @@ possibly an interrupt line. Compatible Vendor / Chip ========== ============= abracon,abb5zes3 AB-RTCMC-32.768kHz-B5ZE-S3: Real Time Clock/Calendar Module with I2C Interface +abracon,abeoz9 AB-RTCMC-32.768kHz-EOZ9: Real Time Clock/Calendar Module with I2C Interface dallas,ds1374 I2C, 32-Bit Binary Counter Watchdog RTC with Trickle Charger and Reset Input/Output dallas,ds1672 Dallas DS1672 Real-time Clock dallas,ds3232 Extremely Accurate I²C RTC with Integrated Crystal and SRAM epson,rx8010 I2C-BUS INTERFACE REAL TIME CLOCK MODULE +epson,rx8571 I2C-BUS INTERFACE REAL TIME CLOCK MODULE with Battery Backed RAM epson,rx8581 I2C-BUS INTERFACE REAL TIME CLOCK MODULE emmicro,em3027 EM Microelectronic EM3027 Real-time Clock isil,isl1208 Intersil ISL1208 Low Power RTC with Battery Backed SRAM isil,isl1218 Intersil ISL1218 Low Power RTC with Battery Backed SRAM isil,isl12022 Intersil ISL12022 Real-time Clock +microcrystal,rv3028 Real Time Clock Module with I2C-Bus microcrystal,rv3029 Real Time Clock Module with I2C-Bus +microcrystal,rv8523 Real Time Clock nxp,pcf2127 Real-time clock nxp,pcf2129 Real-time clock -nxp,pcf8523 Real-time Clock nxp,pcf8563 Real-time clock/calendar -nxp,pcf85063 Tiny Real-Time Clock pericom,pt7c4338 Real-time Clock Module ricoh,r2025sd I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC ricoh,r2221tl I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC @@ -62,3 +68,4 @@ ricoh,rs5c372b I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC ricoh,rv5c386 I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC ricoh,rv5c387a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC sii,s35390a 2-wire CMOS real-time clock +whwave,sd3078 I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt index da50321da34d..3cba12f855b7 100644 --- a/Documentation/devicetree/bindings/serial/8250.txt +++ b/Documentation/devicetree/bindings/serial/8250.txt @@ -21,6 +21,7 @@ Required properties: - "altr,16550-FIFO128" - "fsl,16550-FIFO64" - "fsl,ns16550" + - "intel,xscale-uart" - "ti,da830-uart" - "aspeed,ast2400-vuart" - "aspeed,ast2500-vuart" diff --git a/Documentation/devicetree/bindings/serial/ingenic,uart.txt b/Documentation/devicetree/bindings/serial/ingenic,uart.txt index c3c6406d5cfe..24ed8769f4af 100644 --- a/Documentation/devicetree/bindings/serial/ingenic,uart.txt +++ b/Documentation/devicetree/bindings/serial/ingenic,uart.txt @@ -6,7 +6,8 @@ Required properties: - "ingenic,jz4760-uart", - "ingenic,jz4770-uart", - "ingenic,jz4775-uart", - - "ingenic,jz4780-uart". + - "ingenic,jz4780-uart", + - "ingenic,x1000-uart". - reg : offset and length of the register set for the device. - interrupts : should contain uart interrupt. - clocks : phandles to the module & baud clocks. diff --git a/Documentation/devicetree/bindings/serial/milbeaut-uart.txt b/Documentation/devicetree/bindings/serial/milbeaut-uart.txt new file mode 100644 index 000000000000..3d2fb1a7ba94 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/milbeaut-uart.txt @@ -0,0 +1,21 @@ +Socionext Milbeaut UART controller + +Required properties: +- compatible: should be "socionext,milbeaut-usio-uart". +- reg: offset and length of the register set for the device. +- interrupts: two interrupts specifier. +- interrupt-names: should be "rx", "tx". +- clocks: phandle to the input clock. + +Optional properties: +- auto-flow-control: flow control enable. + +Example: + usio1: usio_uart@1e700010 { + compatible = "socionext,milbeaut-usio-uart"; + reg = <0x1e700010 0x10>; + interrupts = <0 141 0x4>, <0 149 0x4>; + interrupt-names = "rx", "tx"; + clocks = <&clk 2>; + auto-flow-control; + }; diff --git a/Documentation/devicetree/bindings/serial/nvidia,tegra194-tcu.txt b/Documentation/devicetree/bindings/serial/nvidia,tegra194-tcu.txt new file mode 100644 index 000000000000..085a8591accd --- /dev/null +++ b/Documentation/devicetree/bindings/serial/nvidia,tegra194-tcu.txt @@ -0,0 +1,35 @@ +NVIDIA Tegra Combined UART (TCU) + +The TCU is a system for sharing a hardware UART instance among multiple +systems within the Tegra SoC. It is implemented through a mailbox- +based protocol where each "virtual UART" has a pair of mailboxes, one +for transmitting and one for receiving, that is used to communicate +with the hardware implementing the TCU. + +Required properties: +- name : Should be tcu +- compatible + Array of strings + One of: + - "nvidia,tegra194-tcu" +- mbox-names: + "rx" - Mailbox for receiving data from hardware UART + "tx" - Mailbox for transmitting data to hardware UART +- mboxes: Mailboxes corresponding to the mbox-names. + +This node is a mailbox consumer. See the following files for details of +the mailbox subsystem, and the specifiers implemented by the relevant +provider(s): + +- .../mailbox/mailbox.txt +- .../mailbox/nvidia,tegra186-hsp.txt + +Example bindings: +----------------- + +tcu: tcu { + compatible = "nvidia,tegra194-tcu"; + mboxes = <&hsp_top0 TEGRA_HSP_MBOX_TYPE_SM 0>, + <&hsp_aon TEGRA_HSP_MBOX_TYPE_SM 1>; + mbox-names = "rx", "tx"; +}; diff --git a/Documentation/devicetree/bindings/serial/omap_serial.txt b/Documentation/devicetree/bindings/serial/omap_serial.txt index c35d5ece1156..0a9b5444f4e6 100644 --- a/Documentation/devicetree/bindings/serial/omap_serial.txt +++ b/Documentation/devicetree/bindings/serial/omap_serial.txt @@ -22,6 +22,8 @@ Optional properties: - dma-names : "rx" for receive channel, "tx" for transmit channel. - rs485-rts-delay, rs485-rx-during-tx, linux,rs485-enabled-at-boot-time: see rs485.txt - rs485-rts-active-high: drive RTS high when sending (default is low). +- clocks: phandle to the functional clock as per + Documentation/devicetree/bindings/clock/clock-bindings.txt Example: diff --git a/Documentation/devicetree/bindings/serial/pl011.txt b/Documentation/devicetree/bindings/serial/pl011.txt deleted file mode 100644 index 77863aefe9ef..000000000000 --- a/Documentation/devicetree/bindings/serial/pl011.txt +++ /dev/null @@ -1,51 +0,0 @@ -* ARM AMBA Primecell PL011 serial UART - -Required properties: -- compatible: must be "arm,primecell", "arm,pl011", "zte,zx296702-uart" -- reg: exactly one register range with length 0x1000 -- interrupts: exactly one interrupt specifier - -Optional properties: -- pinctrl: - When present, must have one state named "default", - and may contain a second name named "sleep". The former - state sets up pins for ordinary operation whereas - the latter state will put the associated pins to sleep - when the UART is unused -- clocks: - When present, the first clock listed must correspond to - the clock named UARTCLK on the IP block, i.e. the clock - to the external serial line, whereas the second clock - must correspond to the PCLK clocking the internal logic - of the block. Just listing one clock (the first one) is - deprecated. -- clock-names: - When present, the first clock listed must be named - "uartclk" and the second clock listed must be named - "apb_pclk" -- dmas: - When present, may have one or two dma channels. - The first one must be named "rx", the second one - must be named "tx". -- auto-poll: - Enables polling when using RX DMA. -- poll-rate-ms: - Rate at which poll occurs when auto-poll is set, - default 100ms. -- poll-timeout-ms: - Poll timeout when auto-poll is set, default - 3000ms. - -See also bindings/arm/primecell.txt - -Example: - -uart@80120000 { - compatible = "arm,pl011", "arm,primecell"; - reg = <0x80120000 0x1000>; - interrupts = <0 11 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&dma 13 0 0x2>, <&dma 13 0 0x0>; - dma-names = "rx", "tx"; - clocks = <&foo_clk>, <&bar_clk>; - clock-names = "uartclk", "apb_pclk"; -}; diff --git a/Documentation/devicetree/bindings/serial/pl011.yaml b/Documentation/devicetree/bindings/serial/pl011.yaml new file mode 100644 index 000000000000..1a64d59152aa --- /dev/null +++ b/Documentation/devicetree/bindings/serial/pl011.yaml @@ -0,0 +1,126 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/pl011.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM AMBA Primecell PL011 serial UART + +maintainers: + - Rob Herring <robh@kernel.org> + +allOf: + - $ref: /schemas/serial.yaml# + +# Need a custom select here or 'arm,primecell' will match on lots of nodes +select: + properties: + compatible: + contains: + enum: + - arm,pl011 + - zte,zx296702-uart + required: + - compatible + +properties: + compatible: + oneOf: + - items: + - const: arm,pl011 + - const: arm,primecell + - items: + - const: zte,zx296702-uart + - const: arm,primecell + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + pinctrl-0: true + pinctrl-1: true + + pinctrl-names: + description: + When present, must have one state named "default", + and may contain a second name named "sleep". The former + state sets up pins for ordinary operation whereas + the latter state will put the associated pins to sleep + when the UART is unused + minItems: 1 + items: + - const: default + - const: sleep + + clocks: + description: + When present, the first clock listed must correspond to + the clock named UARTCLK on the IP block, i.e. the clock + to the external serial line, whereas the second clock + must correspond to the PCLK clocking the internal logic + of the block. Just listing one clock (the first one) is + deprecated. + maxItems: 2 + + clock-names: + items: + - const: uartclk + - const: apb_pclk + + dmas: + minItems: 1 + maxItems: 2 + + dma-names: + minItems: 1 + items: + - const: rx + - const: tx + + auto-poll: + description: + Enables polling when using RX DMA. + type: boolean + + poll-rate-ms: + description: + Rate at which poll occurs when auto-poll is set. + default 100ms. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - default: 100 + + poll-timeout-ms: + description: + Poll timeout when auto-poll is set, default + 3000ms. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - default: 3000 + +required: + - compatible + - reg + - interrupts + +dependencies: + poll-rate-ms: [ auto-poll ] + poll-timeout-ms: [ auto-poll ] + +additionalProperties: false + +examples: + - | + serial@80120000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x80120000 0x1000>; + interrupts = <0 11 4>; + dmas = <&dma 13 0 0x2>, <&dma 13 0 0x0>; + dma-names = "rx", "tx"; + clocks = <&foo_clk>, <&bar_clk>; + clock-names = "uartclk", "apb_pclk"; + }; + +... diff --git a/Documentation/devicetree/bindings/serial/renesas,rzn1-uart.txt b/Documentation/devicetree/bindings/serial/renesas,rzn1-uart.txt deleted file mode 100644 index 8b9e0d4dc2e4..000000000000 --- a/Documentation/devicetree/bindings/serial/renesas,rzn1-uart.txt +++ /dev/null @@ -1,10 +0,0 @@ -Renesas RZ/N1 UART - -This controller is based on the Synopsys DesignWare ABP UART and inherits all -properties defined in snps-dw-apb-uart.txt except for the compatible property. - -Required properties: -- compatible : The device specific string followed by the generic RZ/N1 string. - Therefore it must be one of: - "renesas,r9a06g032-uart", "renesas,rzn1-uart" - "renesas,r9a06g033-uart", "renesas,rzn1-uart" diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt deleted file mode 100644 index 12bbe9f22560..000000000000 --- a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt +++ /dev/null @@ -1,76 +0,0 @@ -* Synopsys DesignWare ABP UART - -Required properties: -- compatible : "snps,dw-apb-uart" -- reg : offset and length of the register set for the device. -- interrupts : should contain uart interrupt. - -Clock handling: -The clock rate of the input clock needs to be supplied by one of -- clock-frequency : the input clock frequency for the UART. -- clocks : phandle to the input clock - -The supplying peripheral clock can also be handled, needing a second property -- clock-names: tuple listing input clock names. - Required elements: "baudclk", "apb_pclk" - -Optional properties: -- snps,uart-16550-compatible : reflects the value of UART_16550_COMPATIBLE - configuration parameter. Define this if your UART does not implement the busy - functionality. -- resets : phandle to the parent reset controller. -- reg-shift : quantity to shift the register offsets by. If this property is - not present then the register offsets are not shifted. -- reg-io-width : the size (in bytes) of the IO accesses that should be - performed on the device. If this property is not present then single byte - accesses are used. -- dcd-override : Override the DCD modem status signal. This signal will always - be reported as active instead of being obtained from the modem status - register. Define this if your serial port does not use this pin. -- dsr-override : Override the DTS modem status signal. This signal will always - be reported as active instead of being obtained from the modem status - register. Define this if your serial port does not use this pin. -- cts-override : Override the CTS modem status signal. This signal will always - be reported as active instead of being obtained from the modem status - register. Define this if your serial port does not use this pin. -- ri-override : Override the RI modem status signal. This signal will always be - reported as inactive instead of being obtained from the modem status register. - Define this if your serial port does not use this pin. - -Example: - - uart@80230000 { - compatible = "snps,dw-apb-uart"; - reg = <0x80230000 0x100>; - clock-frequency = <3686400>; - interrupts = <10>; - reg-shift = <2>; - reg-io-width = <4>; - dcd-override; - dsr-override; - cts-override; - ri-override; - }; - -Example with one clock: - - uart@80230000 { - compatible = "snps,dw-apb-uart"; - reg = <0x80230000 0x100>; - clocks = <&baudclk>; - interrupts = <10>; - reg-shift = <2>; - reg-io-width = <4>; - }; - -Example with two clocks: - - uart@80230000 { - compatible = "snps,dw-apb-uart"; - reg = <0x80230000 0x100>; - clocks = <&baudclk>, <&apb_pclk>; - clock-names = "baudclk", "apb_pclk"; - interrupts = <10>; - reg-shift = <2>; - reg-io-width = <4>; - }; diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml new file mode 100644 index 000000000000..b42002542690 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml @@ -0,0 +1,140 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/snps-dw-apb-uart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Synopsys DesignWare ABP UART + +maintainers: + - Rob Herring <robh@kernel.org> + +allOf: + - $ref: /schemas/serial.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,r9a06g032-uart + - renesas,r9a06g033-uart + - const: renesas,rzn1-uart + - items: + - enum: + - rockchip,px30-uart + - rockchip,rk3036-uart + - rockchip,rk3066-uart + - rockchip,rk3188-uart + - rockchip,rk3288-uart + - rockchip,rk3328-uart + - rockchip,rk3368-uart + - rockchip,rk3399-uart + - rockchip,rv1108-uart + - const: snps,dw-apb-uart + - items: + - enum: + - brcm,bcm11351-dw-apb-uart + - brcm,bcm21664-dw-apb-uart + - const: snps,dw-apb-uart + - const: snps,dw-apb-uart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clock-frequency: true + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + items: + - const: baudclk + - const: apb_pclk + + snps,uart-16550-compatible: + description: reflects the value of UART_16550_COMPATIBLE configuration + parameter. Define this if your UART does not implement the busy functionality. + type: boolean + + resets: + maxItems: 1 + + reg-shift: true + + reg-io-width: true + + dcd-override: + description: Override the DCD modem status signal. This signal will + always be reported as active instead of being obtained from the modem + status register. Define this if your serial port does not use this + pin. + type: boolean + + dsr-override: + description: Override the DTS modem status signal. This signal will + always be reported as active instead of being obtained from the modem + status register. Define this if your serial port does not use this + pin. + type: boolean + + cts-override: + description: Override the CTS modem status signal. This signal will + always be reported as active instead of being obtained from the modem + status register. Define this if your serial port does not use this + pin. + type: boolean + + ri-override: + description: Override the RI modem status signal. This signal will always + be reported as inactive instead of being obtained from the modem status + register. Define this if your serial port does not use this pin. + type: boolean + +required: + - compatible + - reg + - interrupts + +examples: + - | + serial@80230000 { + compatible = "snps,dw-apb-uart"; + reg = <0x80230000 0x100>; + clock-frequency = <3686400>; + interrupts = <10>; + reg-shift = <2>; + reg-io-width = <4>; + dcd-override; + dsr-override; + cts-override; + ri-override; + }; + + - | + // Example with one clock: + serial@80230000 { + compatible = "snps,dw-apb-uart"; + reg = <0x80230000 0x100>; + clocks = <&baudclk>; + interrupts = <10>; + reg-shift = <2>; + reg-io-width = <4>; + }; + + - | + // Example with two clocks: + serial@80230000 { + compatible = "snps,dw-apb-uart"; + reg = <0x80230000 0x100>; + clocks = <&baudclk>, <&apb_pclk>; + clock-names = "baudclk", "apb_pclk"; + interrupts = <10>; + reg-shift = <2>; + reg-io-width = <4>; + }; +... diff --git a/Documentation/devicetree/bindings/serio/olpc,ap-sp.txt b/Documentation/devicetree/bindings/serio/olpc,ap-sp.txt index 36603419d6f8..0e72183f52bc 100644 --- a/Documentation/devicetree/bindings/serio/olpc,ap-sp.txt +++ b/Documentation/devicetree/bindings/serio/olpc,ap-sp.txt @@ -4,14 +4,10 @@ Required properties: - compatible : "olpc,ap-sp" - reg : base address and length of SoC's WTM registers - interrupts : SP-AP interrupt -- clocks : phandle + clock-specifier for the clock that drives the WTM -- clock-names: should be "sp" Example: ap-sp@d4290000 { compatible = "olpc,ap-sp"; reg = <0xd4290000 0x1000>; interrupts = <40>; - clocks = <&soc_clocks MMP2_CLK_SP>; - clock-names = "sp"; } diff --git a/Documentation/devicetree/bindings/soc/amlogic/clk-measure.txt b/Documentation/devicetree/bindings/soc/amlogic/clk-measure.txt index 205a54bcd7c7..6bf6b43f8dd8 100644 --- a/Documentation/devicetree/bindings/soc/amlogic/clk-measure.txt +++ b/Documentation/devicetree/bindings/soc/amlogic/clk-measure.txt @@ -9,6 +9,8 @@ Required properties: "amlogic,meson-gx-clk-measure" for GX SoCs "amlogic,meson8-clk-measure" for Meson8 SoCs "amlogic,meson8b-clk-measure" for Meson8b SoCs + "amlogic,meson-axg-clk-measure" for AXG SoCs + "amlogic,meson-g12a-clk-measure" for G12a SoCs - reg: base address and size of the Clock Measurer register space. Example: diff --git a/Documentation/devicetree/bindings/soc/bcm/brcm,bcm2835-pm.txt b/Documentation/devicetree/bindings/soc/bcm/brcm,bcm2835-pm.txt new file mode 100644 index 000000000000..3b7d32956391 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/bcm/brcm,bcm2835-pm.txt @@ -0,0 +1,46 @@ +BCM2835 PM (Power domains, watchdog) + +The PM block controls power domains and some reset lines, and includes +a watchdog timer. This binding supersedes the brcm,bcm2835-pm-wdt +binding which covered some of PM's register range and functionality. + +Required properties: + +- compatible: Should be "brcm,bcm2835-pm" +- reg: Specifies base physical address and size of the two + register ranges ("PM" and "ASYNC_BRIDGE" in that + order) +- clocks: a) v3d: The V3D clock from CPRMAN + b) peri_image: The PERI_IMAGE clock from CPRMAN + c) h264: The H264 clock from CPRMAN + d) isp: The ISP clock from CPRMAN +- #reset-cells: Should be 1. This property follows the reset controller + bindings[1]. +- #power-domain-cells: Should be 1. This property follows the power domain + bindings[2]. + +Optional properties: + +- timeout-sec: Contains the watchdog timeout in seconds +- system-power-controller: Whether the watchdog is controlling the + system power. This node follows the power controller bindings[3]. + +[1] Documentation/devicetree/bindings/reset/reset.txt +[2] Documentation/devicetree/bindings/power/power_domain.txt +[3] Documentation/devicetree/bindings/power/power-controller.txt + +Example: + +pm { + compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt"; + #power-domain-cells = <1>; + #reset-cells = <1>; + reg = <0x7e100000 0x114>, + <0x7e00a000 0x24>; + clocks = <&clocks BCM2835_CLOCK_V3D>, + <&clocks BCM2835_CLOCK_PERI_IMAGE>, + <&clocks BCM2835_CLOCK_H264>, + <&clocks BCM2835_CLOCK_ISP>; + clock-names = "v3d", "peri_image", "h264", "isp"; + system-power-controller; +}; diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt index 0b8cc533ca83..cf759e5f9b10 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt @@ -55,7 +55,7 @@ of these nodes are defined by the individual bindings for the specific function = EXAMPLE The following example represents the GLINK RPM node on a MSM8996 device, with the function for the "rpm_request" channel defined, which is used for -regualtors and root clocks. +regulators and root clocks. apcs_glb: mailbox@9820000 { compatible = "qcom,msm8996-apcs-hmss-global"; diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt index ec95705ba692..f3fa313963d5 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt @@ -23,6 +23,7 @@ resources. "qcom,rpm-msm8916" "qcom,rpm-msm8974" "qcom,rpm-msm8998" + "qcom,rpm-sdm660" "qcom,rpm-qcs404" - qcom,smd-channels: diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt index a35af2dafdad..49e1d72d3648 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt @@ -41,12 +41,12 @@ processor ID) and a string identifier. - qcom,local-pid: Usage: required Value type: <u32> - Definition: specifies the identfier of the local endpoint of this edge + Definition: specifies the identifier of the local endpoint of this edge - qcom,remote-pid: Usage: required Value type: <u32> - Definition: specifies the identfier of the remote endpoint of this edge + Definition: specifies the identifier of the remote endpoint of this edge = SUBNODES Each SMP2P pair contain a set of inbound and outbound entries, these are diff --git a/Documentation/devicetree/bindings/sound/adi,adau1977.txt b/Documentation/devicetree/bindings/sound/adi,adau1977.txt index e79aeef73f28..9225472c80b4 100644 --- a/Documentation/devicetree/bindings/sound/adi,adau1977.txt +++ b/Documentation/devicetree/bindings/sound/adi,adau1977.txt @@ -17,12 +17,18 @@ Required properties: Documentation/devicetree/bindings/regulator/regulator.txt Optional properties: - - reset-gpio: the reset pin for the chip, for more details consult + - reset-gpios: the reset pin for the chip, for more details consult Documentation/devicetree/bindings/gpio/gpio.txt - DVDD-supply: supply voltage for the digital core, please consult Documentation/devicetree/bindings/regulator/regulator.txt +- adi,micbias: configures the voltage setting for the MICBIAS pin. + Select 0/1/2/3/4/5/6/7/8 to specify MICBIAS voltage + 5V/5.5V/6V/6.5V/7V/7.5V/8V/8.5V/9V + If not specified the default value will be "7" meaning 8.5 Volts. + This property is only valid for the ADAU1977 + For required properties on SPI, please consult Documentation/devicetree/bindings/spi/spi-bus.txt @@ -40,7 +46,8 @@ Examples: AVDD-supply = <®ulator>; DVDD-supply = <®ulator_digital>; - reset_gpio = <&gpio 10 GPIO_ACTIVE_LOW>; + adi,micbias = <3>; + reset-gpios = <&gpio 10 GPIO_ACTIVE_LOW>; }; adau1977_i2c: adau1977@11 { @@ -50,5 +57,5 @@ Examples: AVDD-supply = <®ulator>; DVDD-supply = <®ulator_digital>; - reset_gpio = <&gpio 10 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio 10 GPIO_ACTIVE_LOW>; }; diff --git a/Documentation/devicetree/bindings/sound/ak4458.txt b/Documentation/devicetree/bindings/sound/ak4458.txt index 7839be78448d..e5820235e0d5 100644 --- a/Documentation/devicetree/bindings/sound/ak4458.txt +++ b/Documentation/devicetree/bindings/sound/ak4458.txt @@ -4,7 +4,7 @@ This device supports I2C mode. Required properties: -- compatible : "asahi-kasei,ak4458" +- compatible : "asahi-kasei,ak4458" or "asahi-kasei,ak4497" - reg : The I2C address of the device for I2C Optional properties: diff --git a/Documentation/devicetree/bindings/sound/audio-graph-scu-card.txt b/Documentation/devicetree/bindings/sound/audio-graph-scu-card.txt deleted file mode 100644 index 62d42768a00b..000000000000 --- a/Documentation/devicetree/bindings/sound/audio-graph-scu-card.txt +++ /dev/null @@ -1,123 +0,0 @@ -Audio-Graph-SCU-Card: - -Audio-Graph-SCU-Card is "Audio-Graph-Card" + "ALSA DPCM". - -It is based on common bindings for device graphs. -see ${LINUX}/Documentation/devicetree/bindings/graph.txt - -Basically, Audio-Graph-SCU-Card property is same as -Simple-Card / Simple-SCU-Card / Audio-Graph-Card. -see ${LINUX}/Documentation/devicetree/bindings/sound/simple-card.txt - ${LINUX}/Documentation/devicetree/bindings/sound/simple-scu-card.txt - ${LINUX}/Documentation/devicetree/bindings/sound/audio-graph-card.txt - -Below are same as Simple-Card / Audio-Graph-Card. - -- label -- dai-format -- frame-master -- bitclock-master -- bitclock-inversion -- frame-inversion -- dai-tdm-slot-num -- dai-tdm-slot-width -- clocks / system-clock-frequency - -Below are same as Simple-SCU-Card. - -- convert-rate -- convert-channels -- prefix -- routing - -Required properties: - -- compatible : "audio-graph-scu-card"; -- dais : list of CPU DAI port{s} - -Example 1. Sampling Rate Conversion - - sound_card { - compatible = "audio-graph-scu-card"; - - label = "sound-card"; - prefix = "codec"; - routing = "codec Playback", "DAI0 Playback", - "DAI0 Capture", "codec Capture"; - convert-rate = <48000>; - - dais = <&cpu_port>; - }; - - audio-codec { - ... - - port { - codec_endpoint: endpoint { - remote-endpoint = <&cpu_endpoint>; - }; - }; - }; - - dai-controller { - ... - cpu_port: port { - cpu_endpoint: endpoint { - remote-endpoint = <&codec_endpoint>; - - dai-format = "left_j"; - ... - }; - }; - }; - -Example 2. 2 CPU 1 Codec (Mixing) - - sound_card { - compatible = "audio-graph-scu-card"; - - label = "sound-card"; - routing = "codec Playback", "DAI0 Playback", - "codec Playback", "DAI1 Playback", - "DAI0 Capture", "codec Capture"; - - dais = <&cpu_port0 - &cpu_port1>; - }; - - audio-codec { - ... - - audio-graph-card,prefix = "codec"; - audio-graph-card,convert-rate = <48000>; - port { - codec_endpoint0: endpoint { - remote-endpoint = <&cpu_endpoint0>; - }; - codec_endpoint1: endpoint { - remote-endpoint = <&cpu_endpoint1>; - }; - }; - }; - - dai-controller { - ... - ports { - cpu_port0: port { - cpu_endpoint0: endpoint { - remote-endpoint = <&codec_endpoint0>; - - dai-format = "left_j"; - ... - }; - }; - cpu_port1: port { - cpu_endpoint1: endpoint { - remote-endpoint = <&codec_endpoint1>; - - dai-format = "left_j"; - ... - }; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/sound/cs35l36.txt b/Documentation/devicetree/bindings/sound/cs35l36.txt new file mode 100644 index 000000000000..912bd162b477 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs35l36.txt @@ -0,0 +1,168 @@ +CS35L36 Speaker Amplifier + +Required properties: + + - compatible : "cirrus,cs35l36" + + - reg : the I2C address of the device for I2C + + - VA-supply, VP-supply : power supplies for the device, + as covered in + Documentation/devicetree/bindings/regulator/regulator.txt. + + - cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost + converter's output voltage in mV. The range is from 2550mV to 12000mV with + increments of 50mV. + (Default) VP + + - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA. + Configures the peak current by monitoring the current through the boost FET. + Range starts at 1600mA and goes to a maximum of 4500mA with increments of + 50mA. + (Default) 4.50 Amps + + - cirrus,boost-ind-nanohenry : Inductor estimation LBST reference value. + Seeds the digital boost converter's inductor estimation block with the initial + inductance value to reference. + + 1000 = 1uH (Default) + 1200 = 1.2uH + +Optional properties: + - cirrus,multi-amp-mode : Boolean to determine if there are more than + one amplifier in the system. If more than one it is best to Hi-Z the ASP + port to prevent bus contention on the output signal + + - cirrus,boost-ctl-select : Boost conerter control source selection. + Selects the source of the BST_CTL target VBST voltage for the boost + converter to generate. + 0x00 - Control Port Value + 0x01 - Class H Tracking (Default) + 0x10 - MultiDevice Sync Value + + - cirrus,amp-pcm-inv : Boolean to determine Amplifier will invert incoming + PCM data + + - cirrus,imon-pol-inv : Boolean to determine Amplifier will invert the + polarity of outbound IMON feedback data + + - cirrus,vmon-pol-inv : Boolean to determine Amplifier will invert the + polarity of outbound VMON feedback data + + - cirrus,dcm-mode-enable : Boost converter automatic DCM Mode enable. + This enables the digital boost converter to operate in a low power + (Discontinuous Conduction) mode during low loading conditions. + + - cirrus,weak-fet-disable : Boolean : The strength of the output drivers is + reduced when operating in a Weak-FET Drive Mode and must not be used to drive + a large load. + + - cirrus,classh-wk-fet-delay : Weak-FET entry delay. Controls the delay + (in ms) before the Class H algorithm switches to the weak-FET voltage + (after the audio falls and remains below the value specified in WKFET_AMP_THLD). + + 0 = 0ms + 1 = 5ms + 2 = 10ms + 3 = 50ms + 4 = 100ms (Default) + 5 = 200ms + 6 = 500ms + 7 = 1000ms + + - cirrus,classh-weak-fet-thld-millivolt : Weak-FET amplifier drive threshold. + Configures the signal threshold at which the PWM output stage enters + weak-FET operation. The range is 50mV to 700mV in 50mV increments. + + - cirrus,temp-warn-threshold : Amplifier overtemperature warning threshold. + Configures the threshold at which the overtemperature warning condition occurs. + When the threshold is met, the overtemperature warning attenuation is applied + and the TEMP_WARN_EINT interrupt status bit is set. + If TEMP_WARN_MASK = 0, INTb is asserted. + + 0 = 105C + 1 = 115C + 2 = 125C (Default) + 3 = 135C + + - cirrus,irq-drive-select : Selects the driver type of the selected interrupt + output. + + 0 = Open-drain + 1 = Push-pull (Default) + + - cirrus,irq-gpio-select : Selects the pin to serve as the programmable + interrupt output. + + 0 = PDM_DATA / SWIRE_SD / INT (Default) + 1 = GPIO + +Optional properties for the "cirrus,vpbr-config" Sub-node + + - cirrus,vpbr-en : VBST brownout prevention enable. Configures whether the + VBST brownout prevention algorithm is enabled or disabled. + + 0 = VBST brownout prevention disabled (default) + 1 = VBST brownout prevention enabled + + See Section 7.31.1 VPBR Config for configuration options & further details + + - cirrus,vpbr-thld : Initial VPBR threshold. Configures the VP brownout + threshold voltage + + - cirrus,cirrus,vpbr-atk-rate : Attenuation attack step rate. Configures the + amount delay between consecutive volume attenuation steps when a brownout + condition is present and the VP brownout condition is in an attacking state. + + - cirrus,vpbr-atk-vol : VP brownout prevention step size. Configures the VP + brownout prevention attacking attenuation step size when operating in either + digital volume or analog gain modes. + + - cirrus,vpbr-max-attn : Maximum attenuation that the VP brownout prevention + can apply to the audio signal. + + - cirrus,vpbr-wait : Configures the delay time between a brownout condition + no longer being present and the VP brownout prevention entering an attenuation + release state. + + - cirrus,vpbr-rel-rate : Attenuation release step rate. Configures the delay + between consecutive volume attenuation release steps when a brownout condition + is not longer present and the VP brownout is in an attenuation release state. + + - cirrus,vpbr-mute-en : During the attack state, if the vpbr-max-attn value + is reached, the error condition still remains, and this bit is set, the audio + is muted. + +Example: + +cs35l36: cs35l36@40 { + compatible = "cirrus,cs35l36"; + reg = <0x40>; + VA-supply = <&dummy_vreg>; + VP-supply = <&dummy_vreg>; + reset-gpios = <&gpio0 54 0>; + interrupt-parent = <&gpio8>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + + cirrus,boost-ind-nanohenry = <1000>; + cirrus,boost-ctl-millivolt = <10000>; + cirrus,boost-peak-milliamp = <4500>; + cirrus,boost-ctl-select = <0x00>; + cirrus,weak-fet-delay = <0x04>; + cirrus,weak-fet-thld = <0x01>; + cirrus,temp-warn-threshold = <0x01>; + cirrus,multi-amp-mode; + cirrus,irq-drive-select = <0x01>; + cirrus,irq-gpio-select = <0x01>; + + cirrus,vpbr-config { + cirrus,vpbr-en = <0x00>; + cirrus,vpbr-thld = <0x05>; + cirrus,vpbr-atk-rate = <0x02>; + cirrus,vpbr-atk-vol = <0x01>; + cirrus,vpbr-max-attn = <0x09>; + cirrus,vpbr-wait = <0x01>; + cirrus,vpbr-rel-rate = <0x05>; + cirrus,vpbr-mute-en = <0x00>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/cs4341.txt b/Documentation/devicetree/bindings/sound/cs4341.txt new file mode 100644 index 000000000000..12b4aa8ef0db --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs4341.txt @@ -0,0 +1,22 @@ +Cirrus Logic CS4341 audio DAC + +This device supports both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + - compatible: "cirrus,cs4341a" + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +For required properties on I2C-bus, please consult +Documentation/devicetree/bindings/i2c/i2c.txt +For required properties on SPI-bus, please consult +Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + codec: cs4341@0 { + #sound-dai-cells = <0>; + compatible = "cirrus,cs4341a"; + reg = <0>; + spi-max-frequency = <6000000>; + }; diff --git a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt index b279b6072bd5..a58f79f5345c 100644 --- a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt +++ b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt @@ -45,6 +45,23 @@ Optional properties: - fck_parent : Should contain a valid clock name which will be used as parent for the McASP fck +Optional GPIO support: +If any McASP pin need to be used as GPIO then the McASP node must have: +... + gpio-controller + #gpio-cells = <2>; +... + +When requesting a GPIO, the first parameter is the PIN index in McASP_P* +registers. +For example to request the AXR2 pin of mcasp8: +function-gpios = <&mcasp8 2 0>; + +Or to request the ACLKR pin of mcasp8: +function-gpios = <&mcasp8 29 0>; + +For generic gpio information, please refer to bindings/gpio/gpio.txt + Example: mcasp0: mcasp0@1d00000 { diff --git a/Documentation/devicetree/bindings/sound/fsl,micfil.txt b/Documentation/devicetree/bindings/sound/fsl,micfil.txt new file mode 100644 index 000000000000..53e227b15277 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/fsl,micfil.txt @@ -0,0 +1,32 @@ +NXP MICFIL Digital Audio Interface (MICFIL). + +The MICFIL digital interface provides a 16-bit audio signal from a PDM +microphone bitstream in a configurable output sampling rate. + +Required properties: + + - compatible : Compatible list, contains "fsl,imx8mm-micfil" + + - reg : Offset and length of the register set for the device. + + - interrupts : Contains the micfil interrupts. + + - clocks : Must contain an entry for each entry in clock-names. + + - clock-names : Must include the "ipg_clk" for register access and + "ipg_clk_app" for internal micfil clock. + + - dmas : Generic dma devicetree binding as described in + Documentation/devicetree/bindings/dma/dma.txt. + +Example: +micfil: micfil@30080000 { + compatible = "fsl,imx8mm-micfil"; + reg = <0x0 0x30080000 0x0 0x10000>; + interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX8MM_CLK_PDM_IPG>, + <&clk IMX8MM_CLK_PDM_ROOT>; + clock-names = "ipg_clk", "ipg_clk_app"; + dmas = <&sdma2 24 26 0x80000000>; +}; diff --git a/Documentation/devicetree/bindings/sound/google,cros-ec-codec.txt b/Documentation/devicetree/bindings/sound/google,cros-ec-codec.txt new file mode 100644 index 000000000000..1084f7f22eea --- /dev/null +++ b/Documentation/devicetree/bindings/sound/google,cros-ec-codec.txt @@ -0,0 +1,26 @@ +* Audio codec controlled by ChromeOS EC + +Google's ChromeOS EC codec is a digital mic codec provided by the +Embedded Controller (EC) and is controlled via a host-command interface. + +An EC codec node should only be found as a sub-node of the EC node (see +Documentation/devicetree/bindings/mfd/cros-ec.txt). + +Required properties: +- compatible: Must contain "google,cros-ec-codec" +- #sound-dai-cells: Should be 1. The cell specifies number of DAIs. +- max-dmic-gain: A number for maximum gain in dB on digital microphone. + +Example: + +cros-ec@0 { + compatible = "google,cros-ec-spi"; + + ... + + cros_ec_codec: ec-codec { + compatible = "google,cros-ec-codec"; + #sound-dai-cells = <1>; + max-dmic-gain = <43>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/ingenic,jz4725b-codec.txt b/Documentation/devicetree/bindings/sound/ingenic,jz4725b-codec.txt new file mode 100644 index 000000000000..05adc0d47b13 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ingenic,jz4725b-codec.txt @@ -0,0 +1,20 @@ +Ingenic JZ4725B codec controller + +Required properties: +- compatible : "ingenic,jz4725b-codec" +- reg : codec registers location and length +- clocks : phandle to the AIC clock. +- clock-names: must be set to "aic". +- #sound-dai-cells: Must be set to 0. + +Example: + +codec: audio-codec@100200a4 { + compatible = "ingenic,jz4725b-codec"; + reg = <0x100200a4 0x8>; + + #sound-dai-cells = <0>; + + clocks = <&cgu JZ4725B_CLK_AIC>; + clock-names = "aic"; +}; diff --git a/Documentation/devicetree/bindings/sound/ingenic,jz4740-codec.txt b/Documentation/devicetree/bindings/sound/ingenic,jz4740-codec.txt new file mode 100644 index 000000000000..1ffcade87e7b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ingenic,jz4740-codec.txt @@ -0,0 +1,20 @@ +Ingenic JZ4740 codec controller + +Required properties: +- compatible : "ingenic,jz4740-codec" +- reg : codec registers location and length +- clocks : phandle to the AIC clock. +- clock-names: must be set to "aic". +- #sound-dai-cells: Must be set to 0. + +Example: + +codec: audio-codec@10020080 { + compatible = "ingenic,jz4740-codec"; + reg = <0x10020080 0x8>; + + #sound-dai-cells = <0>; + + clocks = <&cgu JZ4740_CLK_AIC>; + clock-names = "aic"; +}; diff --git a/Documentation/devicetree/bindings/sound/mt6358.txt b/Documentation/devicetree/bindings/sound/mt6358.txt new file mode 100644 index 000000000000..5465730013a1 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/mt6358.txt @@ -0,0 +1,18 @@ +Mediatek MT6358 Audio Codec + +The communication between MT6358 and SoC is through Mediatek PMIC wrapper. +For more detail, please visit Mediatek PMIC wrapper documentation. + +Must be a child node of PMIC wrapper. + +Required properties: + +- compatible : "mediatek,mt6358-sound". +- Avdd-supply : power source of AVDD + +Example: + +mt6358_snd { + compatible = "mediatek,mt6358-sound"; + Avdd-supply = <&mt6358_vaud28_reg>; +}; diff --git a/Documentation/devicetree/bindings/sound/mt8183-afe-pcm.txt b/Documentation/devicetree/bindings/sound/mt8183-afe-pcm.txt new file mode 100644 index 000000000000..396ba38619f6 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/mt8183-afe-pcm.txt @@ -0,0 +1,36 @@ +Mediatek AFE PCM controller for mt8183 + +Required properties: +- compatible = "mediatek,mt68183-audio"; +- reg: register location and size +- interrupts: should contain AFE interrupt +- power-domains: should define the power domain +- clocks: Must contain an entry for each entry in clock-names +- clock-names: should have these clock names: + "infra_sys_audio_clk", + "mtkaif_26m_clk", + "top_mux_audio", + "top_mux_aud_intbus", + "top_sys_pll3_d4", + "top_clk26m_clk"; + +Example: + + afe: mt8183-afe-pcm@11220000 { + compatible = "mediatek,mt8183-audio"; + reg = <0 0x11220000 0 0x1000>; + interrupts = <GIC_SPI 161 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8183_POWER_DOMAIN_AUDIO>; + clocks = <&infrasys CLK_INFRA_AUDIO>, + <&infrasys CLK_INFRA_AUDIO_26M_BCLK>, + <&topckgen CLK_TOP_MUX_AUDIO>, + <&topckgen CLK_TOP_MUX_AUD_INTBUS>, + <&topckgen CLK_TOP_SYSPLL_D2_D4>, + <&clk26m>; + clock-names = "infra_sys_audio_clk", + "mtkaif_26m_clk", + "top_mux_audio", + "top_mux_aud_intbus", + "top_sys_pll_d2_d4", + "top_clk26m_clk"; + }; diff --git a/Documentation/devicetree/bindings/sound/mtk-btcvsd-snd.txt b/Documentation/devicetree/bindings/sound/mtk-btcvsd-snd.txt new file mode 100644 index 000000000000..679e44839b48 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/mtk-btcvsd-snd.txt @@ -0,0 +1,24 @@ +Mediatek ALSA BT SCO CVSD/MSBC Driver + +Required properties: +- compatible = "mediatek,mtk-btcvsd-snd"; +- reg: register location and size of PKV and SRAM_BANK2 +- interrupts: should contain BTSCO interrupt +- mediatek,infracfg: the phandles of INFRASYS +- mediatek,offset: Array contains of register offset and mask + infra_misc_offset, + infra_conn_bt_cvsd_mask, + cvsd_mcu_read_offset, + cvsd_mcu_write_offset, + cvsd_packet_indicator_offset + +Example: + + mtk-btcvsd-snd@18000000 { + compatible = "mediatek,mtk-btcvsd-snd"; + reg=<0 0x18000000 0 0x1000>, + <0 0x18080000 0 0x8000>; + interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_LOW>; + mediatek,infracfg = <&infrasys>; + mediatek,offset = <0xf00 0x800 0xfd0 0xfd4 0xfd8>; + }; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt index 44d27456e8a4..21cd310963b1 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt @@ -13,6 +13,10 @@ Required properties: See ../reset/reset.txt for details. - reset-names : Must include the following entries: hda, hda2hdmi, hda2codec_2x +Optional properties: +- nvidia,model : The user-visible name of this sound complex. Since the property + is optional, legacy boards can use default name provided in hda driver. + Example: hda@70030000 { @@ -27,4 +31,5 @@ hda@70030000 { <&tegra_car 128>, /* hda2hdmi */ <&tegra_car 111>; /* hda2codec_2x */ reset-names = "hda", "hda2hdmi", "hda2codec_2x"; + nvidia,model = "jetson-tk1-hda"; }; diff --git a/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt index fdcea3d12ee5..e7d17dda55db 100644 --- a/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt +++ b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt @@ -30,6 +30,7 @@ Required properties - vdd-cdc-io-supply: phandle to VDD_CDC_IO regulator DT node. - vdd-cdc-tx-rx-cx-supply: phandle to VDD_CDC_TX/RX/CX regulator DT node. - vdd-micbias-supply: phandle of VDD_MICBIAS supply's regulator DT node. + Optional Properties: - qcom,mbhc-vthreshold-low: Array of 5 threshold voltages in mV for 5 buttons detection on headset when the mbhc is powered up @@ -92,9 +93,9 @@ spmi_bus { "cdc_ear_cnp_int", "cdc_hphr_cnp_int", "cdc_hphl_cnp_int"; - VDD-CDC-IO-supply = <&pm8916_l5>; - VDD-CDC-TX-RX-CX-supply = <&pm8916_l5>; - VDD-MICBIAS-supply = <&pm8916_l13>; + vdd-cdc-io-supply = <&pm8916_l5>; + vdd-cdc-tx-rx-cx-supply = <&pm8916_l5>; + vdd-micbias-supply = <&pm8916_l13>; #sound-dai-cells = <1>; }; }; diff --git a/Documentation/devicetree/bindings/sound/qcom,wcd9335.txt b/Documentation/devicetree/bindings/sound/qcom,wcd9335.txt index 1d8d49e30af7..5d6ea66a863f 100644 --- a/Documentation/devicetree/bindings/sound/qcom,wcd9335.txt +++ b/Documentation/devicetree/bindings/sound/qcom,wcd9335.txt @@ -34,12 +34,12 @@ Required properties with SLIMbus Interface: Definition: Interrupt names of WCD INTR1 and INTR2 Should be: "intr1", "intr2" -- reset-gpio: +- reset-gpios: Usage: required Value type: <String Array> Definition: Reset gpio line -- qcom,ifd: +- slim-ifc-dev: Usage: required Value type: <phandle> Definition: SLIM interface device @@ -104,13 +104,13 @@ Required properties with SLIMbus Interface: Value type: <u32> Definition: Must be 1 -codec@1{ +audio-codec@1{ compatible = "slim217,1a0"; reg = <1 0>; interrupts = <&msmgpio 54 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "intr2" - reset-gpio = <&msmgpio 64 0>; - qcom,ifd = <&wc9335_ifd>; + reset-gpios = <&msmgpio 64 0>; + slim-ifc-dev = <&wc9335_ifd>; clock-names = "mclk", "native"; clocks = <&rpmcc RPM_SMD_DIV_CLK1>, <&rpmcc RPM_SMD_BB_CLK1>; diff --git a/Documentation/devicetree/bindings/sound/rockchip,rk3328-codec.txt b/Documentation/devicetree/bindings/sound/rockchip,rk3328-codec.txt new file mode 100644 index 000000000000..2469588c7ccb --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rockchip,rk3328-codec.txt @@ -0,0 +1,23 @@ +* Rockchip Rk3328 internal codec + +Required properties: + +- compatible: "rockchip,rk3328-codec" +- reg: physical base address of the controller and length of memory mapped + region. +- rockchip,grf: the phandle of the syscon node for GRF register. +- clocks: a list of phandle + clock-specifer pairs, one for each entry in clock-names. +- clock-names: should be "pclk". +- spk-depop-time-ms: speak depop time msec. + +Example for rk3328 internal codec: + +codec: codec@ff410000 { + compatible = "rockchip,rk3328-codec"; + reg = <0x0 0xff410000 0x0 0x1000>; + rockchip,grf = <&grf>; + clocks = <&cru PCLK_ACODEC>; + clock-names = "pclk"; + spk-depop-time-ms = 100; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/sound/sgtl5000.txt b/Documentation/devicetree/bindings/sound/sgtl5000.txt index 9c58f724396a..9d9ff5184939 100644 --- a/Documentation/devicetree/bindings/sound/sgtl5000.txt +++ b/Documentation/devicetree/bindings/sound/sgtl5000.txt @@ -37,6 +37,15 @@ VDDIO 1.8V 2.5V 3.3V 2 = 3.33 mA 5.74 mA 8.03 mA 3 = 4.99 mA 8.61 mA 12.05 mA +- sclk-strength: the SCLK pad strength. Possible values are: +0, 1, 2 and 3 as per the table below: + +VDDIO 1.8V 2.5V 3.3V +0 = Disable +1 = 1.66 mA 2.87 mA 4.02 mA +2 = 3.33 mA 5.74 mA 8.03 mA +3 = 4.99 mA 8.61 mA 12.05 mA + Example: sgtl5000: codec@a { diff --git a/Documentation/devicetree/bindings/sound/simple-scu-card.txt b/Documentation/devicetree/bindings/sound/simple-scu-card.txt deleted file mode 100644 index 3a2f71616cda..000000000000 --- a/Documentation/devicetree/bindings/sound/simple-scu-card.txt +++ /dev/null @@ -1,94 +0,0 @@ -ASoC Simple SCU Sound Card - -Simple SCU Sound Card is "Simple Sound Card" + "ALSA DPCM". -For example, you can use this driver if you want to exchange sampling rate convert, -Mixing, etc... - -Required properties: - -- compatible : "simple-scu-audio-card" - "renesas,rsrc-card" -Optional properties: - -- simple-audio-card,name : see simple-audio-card.txt -- simple-audio-card,cpu : see simple-audio-card.txt -- simple-audio-card,codec : see simple-audio-card.txt - -Optional subnode properties: - -- simple-audio-card,format : see simple-audio-card.txt -- simple-audio-card,frame-master : see simple-audio-card.txt -- simple-audio-card,bitclock-master : see simple-audio-card.txt -- simple-audio-card,bitclock-inversion : see simple-audio-card.txt -- simple-audio-card,frame-inversion : see simple-audio-card.txt -- simple-audio-card,convert-rate : platform specified sampling rate convert -- simple-audio-card,convert-channels : platform specified converted channel size (2 - 8 ch) -- simple-audio-card,prefix : see routing -- simple-audio-card,widgets : Please refer to widgets.txt. -- simple-audio-card,routing : A list of the connections between audio components. - Each entry is a pair of strings, the first being the connection's sink, - the second being the connection's source. Valid names for sources. - use audio-prefix if some components is using same sink/sources naming. - it can be used if compatible was "renesas,rsrc-card"; - -Required CPU/CODEC subnodes properties: - -- sound-dai : see simple-audio-card.txt - -Optional CPU/CODEC subnodes properties: - -- clocks / system-clock-frequency : see simple-audio-card.txt - -Example 1. Sampling Rate Conversion - -sound { - compatible = "simple-scu-audio-card"; - - simple-audio-card,name = "rsnd-ak4643"; - simple-audio-card,format = "left_j"; - simple-audio-card,bitclock-master = <&sndcodec>; - simple-audio-card,frame-master = <&sndcodec>; - - simple-audio-card,convert-rate = <48000>; - - simple-audio-card,prefix = "ak4642"; - simple-audio-card,routing = "ak4642 Playback", "DAI0 Playback", - "DAI0 Capture", "ak4642 Capture"; - - sndcpu: simple-audio-card,cpu { - sound-dai = <&rcar_sound>; - }; - - sndcodec: simple-audio-card,codec { - sound-dai = <&ak4643>; - system-clock-frequency = <11289600>; - }; -}; - -Example 2. 2 CPU 1 Codec (Mixing) - -sound { - compatible = "simple-scu-audio-card"; - - simple-audio-card,name = "rsnd-ak4643"; - simple-audio-card,format = "left_j"; - simple-audio-card,bitclock-master = <&dpcmcpu>; - simple-audio-card,frame-master = <&dpcmcpu>; - - simple-audio-card,routing = "ak4642 Playback", "DAI0 Playback", - "ak4642 Playback", "DAI1 Playback"; - - dpcmcpu: cpu@0 { - sound-dai = <&rcar_sound 0>; - }; - - cpu@1 { - sound-dai = <&rcar_sound 1>; - }; - - codec { - prefix = "ak4642"; - sound-dai = <&ak4643>; - clocks = <&audio_clock>; - }; -}; diff --git a/Documentation/devicetree/bindings/sound/sprd-pcm.txt b/Documentation/devicetree/bindings/sound/sprd-pcm.txt new file mode 100644 index 000000000000..4b23e84b2e57 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/sprd-pcm.txt @@ -0,0 +1,23 @@ +* Spreadtrum DMA platfrom bindings + +Required properties: +- compatible: Should be "sprd,pcm-platform". +- dmas: Specify the list of DMA controller phandle and DMA request line ordered pairs. +- dma-names: Identifier string for each DMA request line in the dmas property. + These strings correspond 1:1 with the ordered pairs in dmas. + +Example: + + audio_platform:platform@0 { + compatible = "sprd,pcm-platform"; + dmas = <&agcp_dma 1 1>, <&agcp_dma 2 2>, + <&agcp_dma 3 3>, <&agcp_dma 4 4>, + <&agcp_dma 5 5>, <&agcp_dma 6 6>, + <&agcp_dma 7 7>, <&agcp_dma 8 8>, + <&agcp_dma 9 9>, <&agcp_dma 10 10>; + dma-names = "normal_p_l", "normal_p_r", + "normal_c_l", "normal_c_r", + "voice_c", "fast_p", + "loop_c", "loop_p", + "voip_c", "voip_p"; + }; diff --git a/Documentation/devicetree/bindings/sound/xlnx,audio-formatter.txt b/Documentation/devicetree/bindings/sound/xlnx,audio-formatter.txt new file mode 100644 index 000000000000..cbc93c8f4963 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/xlnx,audio-formatter.txt @@ -0,0 +1,29 @@ +Device-Tree bindings for Xilinx PL audio formatter + +The IP core supports DMA, data formatting(AES<->PCM conversion) +of audio samples. + +Required properties: + - compatible: "xlnx,audio-formatter-1.0" + - interrupt-names: Names specified to list of interrupts in same + order mentioned under "interrupts". + List of supported interrupt names are: + "irq_mm2s" : interrupt from MM2S block + "irq_s2mm" : interrupt from S2MM block + - interrupts-parent: Phandle for interrupt controller. + - interrupts: List of Interrupt numbers. + - reg: Base address and size of the IP core instance. + - clock-names: List of input clocks. + Required elements: "s_axi_lite_aclk", "aud_mclk" + - clocks: Input clock specifier. Refer to common clock bindings. + +Example: + audio_ss_0_audio_formatter_0: audio_formatter@80010000 { + compatible = "xlnx,audio-formatter-1.0"; + interrupt-names = "irq_mm2s", "irq_s2mm"; + interrupt-parent = <&gic>; + interrupts = <0 104 4>, <0 105 4>; + reg = <0x0 0x80010000 0x0 0x1000>; + clock-names = "s_axi_lite_aclk", "aud_mclk"; + clocks = <&clk 71>, <&clk_wiz_1 0>; + }; diff --git a/Documentation/devicetree/bindings/sound/xlnx,spdif.txt b/Documentation/devicetree/bindings/sound/xlnx,spdif.txt new file mode 100644 index 000000000000..15c2d64d247c --- /dev/null +++ b/Documentation/devicetree/bindings/sound/xlnx,spdif.txt @@ -0,0 +1,28 @@ +Device-Tree bindings for Xilinx SPDIF IP + +The IP supports playback and capture of SPDIF audio + +Required properties: + - compatible: "xlnx,spdif-2.0" + - clock-names: List of input clocks. + Required elements: "s_axi_aclk", "aud_clk_i" + - clocks: Input clock specifier. Refer to common clock bindings. + - reg: Base address and address length of the IP core instance. + - interrupts-parent: Phandle for interrupt controller. + - interrupts: List of Interrupt numbers. + - xlnx,spdif-mode: 0 :- receiver mode + 1 :- transmitter mode + - xlnx,aud_clk_i: input audio clock value. + +Example: + spdif_0: spdif@80010000 { + clock-names = "aud_clk_i", "s_axi_aclk"; + clocks = <&misc_clk_0>, <&clk 71>; + compatible = "xlnx,spdif-2.0"; + interrupt-names = "spdif_interrupt"; + interrupt-parent = <&gic>; + interrupts = <0 91 4>; + reg = <0x0 0x80010000 0x0 0x10000>; + xlnx,spdif-mode = <1>; + xlnx,aud_clk_i = <49152913>; + }; diff --git a/Documentation/devicetree/bindings/spi/atmel-quadspi.txt b/Documentation/devicetree/bindings/spi/atmel-quadspi.txt index b93c1e2f25dd..7c40ea694352 100644 --- a/Documentation/devicetree/bindings/spi/atmel-quadspi.txt +++ b/Documentation/devicetree/bindings/spi/atmel-quadspi.txt @@ -1,14 +1,19 @@ * Atmel Quad Serial Peripheral Interface (QSPI) Required properties: -- compatible: Should be "atmel,sama5d2-qspi". +- compatible: Should be one of the following: + - "atmel,sama5d2-qspi" + - "microchip,sam9x60-qspi" - reg: Should contain the locations and lengths of the base registers and the mapped memory. - reg-names: Should contain the resource reg names: - qspi_base: configuration register address space - qspi_mmap: memory mapped address space - interrupts: Should contain the interrupt for the device. -- clocks: The phandle of the clock needed by the QSPI controller. +- clocks: Should reference the peripheral clock and the QSPI system + clock if available. +- clock-names: Should contain "pclk" for the peripheral clock and "qspick" + for the system clock when available. - #address-cells: Should be <1>. - #size-cells: Should be <0>. @@ -19,7 +24,8 @@ spi@f0020000 { reg = <0xf0020000 0x100>, <0xd0000000 0x8000000>; reg-names = "qspi_base", "qspi_mmap"; interrupts = <52 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&spi0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 52>; + clock-names = "pclk"; #address-cells = <1>; #size-cells = <0>; pinctrl-names = "default"; diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt index e3c48b20b1a6..2d3264140cc5 100644 --- a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt @@ -10,6 +10,7 @@ Required properties: - "fsl,imx35-cspi" for SPI compatible with the one integrated on i.MX35 - "fsl,imx51-ecspi" for SPI compatible with the one integrated on i.MX51 - "fsl,imx53-ecspi" for SPI compatible with the one integrated on i.MX53 and later Soc + - "fsl,imx8mq-ecspi" for SPI compatible with the one integrated on i.MX8M - reg : Offset and length of the register set for the device - interrupts : Should contain CSPI/eCSPI interrupt - clocks : Clock specifiers for both ipg and per clocks. diff --git a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-qspi.txt index 483e9cfac1b1..e8f1d627d288 100644 --- a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-fsl-qspi.txt @@ -14,15 +14,13 @@ Required properties: - clocks : The clocks needed by the QuadSPI controller - clock-names : Should contain the name of the clocks: "qspi_en" and "qspi". -Optional properties: - - fsl,qspi-has-second-chip: The controller has two buses, bus A and bus B. - Each bus can be connected with two NOR flashes. - Most of the time, each bus only has one NOR flash - connected, this is the default case. - But if there are two NOR flashes connected to the - bus, you should enable this property. - (Please check the board's schematic.) - - big-endian : That means the IP register is big endian +Required SPI slave node properties: + - reg: There are two buses (A and B) with two chip selects each. + This encodes to which bus and CS the flash is connected: + <0>: Bus A, CS 0 + <1>: Bus A, CS 1 + <2>: Bus B, CS 0 + <3>: Bus B, CS 1 Example: @@ -40,7 +38,7 @@ qspi0: quadspi@40044000 { }; }; -Example showing the usage of two SPI NOR devices: +Example showing the usage of two SPI NOR devices on bus A: &qspi2 { pinctrl-names = "default"; diff --git a/Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt b/Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt new file mode 100644 index 000000000000..2cd67eb727d4 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt @@ -0,0 +1,39 @@ +* NXP Flex Serial Peripheral Interface (FSPI) + +Required properties: + - compatible : Should be "nxp,lx2160a-fspi" + - reg : First contains the register location and length, + Second contains the memory mapping address and length + - reg-names : Should contain the resource reg names: + - fspi_base: configuration register address space + - fspi_mmap: memory mapped address space + - interrupts : Should contain the interrupt for the device + +Required SPI slave node properties: + - reg : There are two buses (A and B) with two chip selects each. + This encodes to which bus and CS the flash is connected: + - <0>: Bus A, CS 0 + - <1>: Bus A, CS 1 + - <2>: Bus B, CS 0 + - <3>: Bus B, CS 1 + +Example showing the usage of two SPI NOR slave devices on bus A: + +fspi0: spi@20c0000 { + compatible = "nxp,lx2160a-fspi"; + reg = <0x0 0x20c0000 0x0 0x10000>, <0x0 0x20000000 0x0 0x10000000>; + reg-names = "fspi_base", "fspi_mmap"; + interrupts = <0 25 0x4>; /* Level high type */ + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "fspi_en", "fspi"; + + mt35xu512aba0: flash@0 { + reg = <0>; + .... + }; + + mt35xu512aba1: flash@1 { + reg = <1>; + .... + }; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-sifive.txt b/Documentation/devicetree/bindings/spi/spi-sifive.txt new file mode 100644 index 000000000000..3f5c6e438972 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-sifive.txt @@ -0,0 +1,37 @@ +SiFive SPI controller Device Tree Bindings +------------------------------------------ + +Required properties: +- compatible : Should be "sifive,<chip>-spi" and "sifive,spi<version>". + Supported compatible strings are: + "sifive,fu540-c000-spi" for the SiFive SPI v0 as integrated + onto the SiFive FU540 chip, and "sifive,spi0" for the SiFive + SPI v0 IP block with no chip integration tweaks. + Please refer to sifive-blocks-ip-versioning.txt for details +- reg : Physical base address and size of SPI registers map + A second (optional) range can indicate memory mapped flash +- interrupts : Must contain one entry +- interrupt-parent : Must be core interrupt controller +- clocks : Must reference the frequency given to the controller +- #address-cells : Must be '1', indicating which CS to use +- #size-cells : Must be '0' + +Optional properties: +- sifive,fifo-depth : Depth of hardware queues; defaults to 8 +- sifive,max-bits-per-word : Maximum bits per word; defaults to 8 + +SPI RTL that corresponds to the IP block version numbers can be found here: +https://github.com/sifive/sifive-blocks/tree/master/src/main/scala/devices/spi + +Example: + spi: spi@10040000 { + compatible = "sifive,fu540-c000-spi", "sifive,spi0"; + reg = <0x0 0x10040000 0x0 0x1000 0x0 0x20000000 0x0 0x10000000>; + interrupt-parent = <&plic>; + interrupts = <51>; + clocks = <&tlclk>; + #address-cells = <1>; + #size-cells = <0>; + sifive,fifo-depth = <8>; + sifive,max-bits-per-word = <8>; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-sprd.txt b/Documentation/devicetree/bindings/spi/spi-sprd.txt index bad211a19da4..3c7eacce0ee3 100644 --- a/Documentation/devicetree/bindings/spi/spi-sprd.txt +++ b/Documentation/devicetree/bindings/spi/spi-sprd.txt @@ -14,6 +14,11 @@ Required properties: address on the SPI bus. Should be set to 1. - #size-cells: Should be set to 0. +Optional properties: +dma-names: Should contain names of the SPI used DMA channel. +dmas: Should contain DMA channels and DMA slave ids which the SPI used + sorted in the same order as the dma-names property. + Example: spi0: spi@70a00000{ compatible = "sprd,sc9860-spi"; @@ -21,6 +26,8 @@ spi0: spi@70a00000{ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; clock-names = "spi", "source","enable"; clocks = <&clk_spi0>, <&ext_26m>, <&clk_ap_apb_gates 5>; + dma-names = "rx_chn", "tx_chn"; + dmas = <&apdma 11 11>, <&apdma 12 12>; #address-cells = <1>; #size-cells = <0>; }; diff --git a/Documentation/devicetree/bindings/spi/spi-stm32.txt b/Documentation/devicetree/bindings/spi/spi-stm32.txt index 1b3fa2c119d5..d82755c63eaf 100644 --- a/Documentation/devicetree/bindings/spi/spi-stm32.txt +++ b/Documentation/devicetree/bindings/spi/spi-stm32.txt @@ -7,7 +7,9 @@ from 4 to 32-bit data size. Although it can be configured as master or slave, only master is supported by the driver. Required properties: -- compatible: Must be "st,stm32h7-spi". +- compatible: Should be one of: + "st,stm32h7-spi" + "st,stm32f4-spi" - reg: Offset and length of the device's register set. - interrupts: Must contain the interrupt id. - clocks: Must contain an entry for spiclk (which feeds the internal clock @@ -30,8 +32,9 @@ Child nodes represent devices on the SPI bus See ../spi/spi-bus.txt Optional properties: -- st,spi-midi-ns: (Master Inter-Data Idleness) minimum time delay in - nanoseconds inserted between two consecutive data frames. +- st,spi-midi-ns: Only for STM32H7, (Master Inter-Data Idleness) minimum time + delay in nanoseconds inserted between two consecutive data + frames. Example: diff --git a/Documentation/devicetree/bindings/sram/milbeaut-smp-sram.txt b/Documentation/devicetree/bindings/sram/milbeaut-smp-sram.txt new file mode 100644 index 000000000000..194f6a3c1c1e --- /dev/null +++ b/Documentation/devicetree/bindings/sram/milbeaut-smp-sram.txt @@ -0,0 +1,24 @@ +Milbeaut SRAM for smp bringup + +Milbeaut SoCs use a part of the sram for the bringup of the secondary cores. +Once they get powered up in the bootloader, they stay at the specific part +of the sram. +Therefore the part needs to be added as the sub-node of mmio-sram. + +Required sub-node properties: +- compatible : should be "socionext,milbeaut-smp-sram" + +Example: + + sram: sram@0 { + compatible = "mmio-sram"; + reg = <0x0 0x10000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x0 0x10000>; + + smp-sram@f100 { + compatible = "socionext,milbeaut-smp-sram"; + reg = <0xf100 0x20>; + }; + }; diff --git a/Documentation/devicetree/bindings/sram/sunxi-sram.txt b/Documentation/devicetree/bindings/sram/sunxi-sram.txt index ab5a70bb9a64..380246a805f2 100644 --- a/Documentation/devicetree/bindings/sram/sunxi-sram.txt +++ b/Documentation/devicetree/bindings/sram/sunxi-sram.txt @@ -63,6 +63,7 @@ The valid sections compatible for H5 are: The valid sections compatible for H6 are: - allwinner,sun50i-h6-sram-c, allwinner,sun50i-a64-sram-c + - allwinner,sun50i-h6-sram-c1, allwinner,sun4i-a10-sram-c1 The valid sections compatible for F1C100s are: - allwinner,suniv-f1c100s-sram-d, allwinner,sun4i-a10-sram-d diff --git a/Documentation/devicetree/bindings/thermal/brcm,sr-thermal.txt b/Documentation/devicetree/bindings/thermal/brcm,sr-thermal.txt new file mode 100644 index 000000000000..3ab330219d45 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/brcm,sr-thermal.txt @@ -0,0 +1,105 @@ +* Broadcom Stingray Thermal + +This binding describes thermal sensors that is part of Stingray SoCs. + +Required properties: +- compatible : Must be "brcm,sr-thermal" +- reg : Memory where tmon data will be available. +- brcm,tmon-mask: A one cell bit mask of valid TMON sources. + Each bit represents single TMON source. +- #thermal-sensor-cells : Thermal sensor phandler +- polling-delay: Max number of milliseconds to wait between polls. +- thermal-sensors: A list of thermal sensor phandles and specifier. + specifier value is tmon ID and it should be + in correspond with brcm,tmon-mask. +- temperature: trip temperature threshold in millicelsius. + +Example: + tmons { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x0 0x8f100000 0x100>; + + tmon: tmon@0 { + compatible = "brcm,sr-thermal"; + reg = <0x0 0x40>; + brcm,tmon-mask = <0x3f>; + #thermal-sensor-cells = <1>; + }; + }; + + thermal-zones { + ihost0_thermal: ihost0-thermal { + polling-delay-passive = <0>; + polling-delay = <1000>; + thermal-sensors = <&tmon 0>; + trips { + cpu-crit { + temperature = <105000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; + ihost1_thermal: ihost1-thermal { + polling-delay-passive = <0>; + polling-delay = <1000>; + thermal-sensors = <&tmon 1>; + trips { + cpu-crit { + temperature = <105000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; + ihost2_thermal: ihost2-thermal { + polling-delay-passive = <0>; + polling-delay = <1000>; + thermal-sensors = <&tmon 2>; + trips { + cpu-crit { + temperature = <105000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; + ihost3_thermal: ihost3-thermal { + polling-delay-passive = <0>; + polling-delay = <1000>; + thermal-sensors = <&tmon 3>; + trips { + cpu-crit { + temperature = <105000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; + crmu_thermal: crmu-thermal { + polling-delay-passive = <0>; + polling-delay = <1000>; + thermal-sensors = <&tmon 4>; + trips { + cpu-crit { + temperature = <105000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; + nitro_thermal: nitro-thermal { + polling-delay-passive = <0>; + polling-delay = <1000>; + thermal-sensors = <&tmon 5>; + trips { + cpu-crit { + temperature = <105000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt index 41d6a443ad66..f8d7831f3974 100644 --- a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt @@ -13,6 +13,7 @@ Required properties: - "mediatek,mt2701-thermal" : For MT2701 family of SoCs - "mediatek,mt2712-thermal" : For MT2712 family of SoCs - "mediatek,mt7622-thermal" : For MT7622 SoC + - "mediatek,mt8183-thermal" : For MT8183 family of SoCs - reg: Address range of the thermal controller - interrupts: IRQ for the thermal controller - clocks, clock-names: Clocks needed for the thermal controller. required diff --git a/Documentation/devicetree/bindings/timer/fsl,imxgpt.txt b/Documentation/devicetree/bindings/timer/fsl,imxgpt.txt index 9809b11f7180..5d8fd5b52598 100644 --- a/Documentation/devicetree/bindings/timer/fsl,imxgpt.txt +++ b/Documentation/devicetree/bindings/timer/fsl,imxgpt.txt @@ -2,17 +2,44 @@ Freescale i.MX General Purpose Timer (GPT) Required properties: -- compatible : should be "fsl,<soc>-gpt" -- reg : Specifies base physical address and size of the registers. -- interrupts : A list of 4 interrupts; one per timer channel. -- clocks : The clocks provided by the SoC to drive the timer. +- compatible : should be one of following: + for i.MX1: + - "fsl,imx1-gpt"; + for i.MX21: + - "fsl,imx21-gpt"; + for i.MX27: + - "fsl,imx27-gpt", "fsl,imx21-gpt"; + for i.MX31: + - "fsl,imx31-gpt"; + for i.MX25: + - "fsl,imx25-gpt", "fsl,imx31-gpt"; + for i.MX50: + - "fsl,imx50-gpt", "fsl,imx31-gpt"; + for i.MX51: + - "fsl,imx51-gpt", "fsl,imx31-gpt"; + for i.MX53: + - "fsl,imx53-gpt", "fsl,imx31-gpt"; + for i.MX6Q: + - "fsl,imx6q-gpt", "fsl,imx31-gpt"; + for i.MX6DL: + - "fsl,imx6dl-gpt"; + for i.MX6SL: + - "fsl,imx6sl-gpt", "fsl,imx6dl-gpt"; + for i.MX6SX: + - "fsl,imx6sx-gpt", "fsl,imx6dl-gpt"; +- reg : specifies base physical address and size of the registers. +- interrupts : should be the gpt interrupt. +- clocks : the clocks provided by the SoC to drive the timer, must contain + an entry for each entry in clock-names. +- clock-names : must include "ipg" entry first, then "per" entry. Example: gpt1: timer@10003000 { - compatible = "fsl,imx27-gpt", "fsl,imx1-gpt"; + compatible = "fsl,imx27-gpt", "fsl,imx21-gpt"; reg = <0x10003000 0x1000>; interrupts = <26>; - clocks = <&clks 46>, <&clks 61>; + clocks = <&clks IMX27_CLK_GPT1_IPG_GATE>, + <&clks IMX27_CLK_PER1_GATE>; clock-names = "ipg", "per"; }; diff --git a/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt b/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt index 18d4d0166c76..ff7c567a7972 100644 --- a/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt +++ b/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt @@ -1,7 +1,7 @@ -Mediatek Timers +MediaTek Timers --------------- -Mediatek SoCs have two different timers on different platforms, +MediaTek SoCs have two different timers on different platforms, - GPT (General Purpose Timer) - SYST (System Timer) @@ -9,6 +9,7 @@ The proper timer will be selected automatically by driver. Required properties: - compatible should contain: + For those SoCs that use GPT * "mediatek,mt2701-timer" for MT2701 compatible timers (GPT) * "mediatek,mt6580-timer" for MT6580 compatible timers (GPT) * "mediatek,mt6589-timer" for MT6589 compatible timers (GPT) @@ -17,7 +18,11 @@ Required properties: * "mediatek,mt8135-timer" for MT8135 compatible timers (GPT) * "mediatek,mt8173-timer" for MT8173 compatible timers (GPT) * "mediatek,mt6577-timer" for MT6577 and all above compatible timers (GPT) - * "mediatek,mt6765-timer" for MT6765 compatible timers (SYST) + + For those SoCs that use SYST + * "mediatek,mt7629-timer" for MT7629 compatible timers (SYST) + * "mediatek,mt6765-timer" for MT6765 and all above compatible timers (SYST) + - reg: Should contain location and length for timer register. - clocks: Should contain system clock. diff --git a/Documentation/devicetree/bindings/timer/nvidia,tegra210-timer.txt b/Documentation/devicetree/bindings/timer/nvidia,tegra210-timer.txt new file mode 100644 index 000000000000..032cda96fe0d --- /dev/null +++ b/Documentation/devicetree/bindings/timer/nvidia,tegra210-timer.txt @@ -0,0 +1,36 @@ +NVIDIA Tegra210 timer + +The Tegra210 timer provides fourteen 29-bit timer counters and one 32-bit +timestamp counter. The TMRs run at either a fixed 1 MHz clock rate derived +from the oscillator clock (TMR0-TMR9) or directly at the oscillator clock +(TMR10-TMR13). Each TMR can be programmed to generate one-shot, periodic, +or watchdog interrupts. + +Required properties: +- compatible : "nvidia,tegra210-timer". +- reg : Specifies base physical address and size of the registers. +- interrupts : A list of 14 interrupts; one per each timer channels 0 through + 13. +- clocks : Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. + +timer@60005000 { + compatible = "nvidia,tegra210-timer"; + reg = <0x0 0x60005000 0x0 0x400>; + interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA210_CLK_TIMER>; + clock-names = "timer"; +}; diff --git a/Documentation/devicetree/bindings/timer/renesas,cmt.txt b/Documentation/devicetree/bindings/timer/renesas,cmt.txt index 862a80f0380a..c0594450e9ef 100644 --- a/Documentation/devicetree/bindings/timer/renesas,cmt.txt +++ b/Documentation/devicetree/bindings/timer/renesas,cmt.txt @@ -32,6 +32,8 @@ Required Properties: - "renesas,r8a77470-cmt1" for the 48-bit CMT1 device included in r8a77470. - "renesas,r8a774a1-cmt0" for the 32-bit CMT0 device included in r8a774a1. - "renesas,r8a774a1-cmt1" for the 48-bit CMT1 device included in r8a774a1. + - "renesas,r8a774c0-cmt0" for the 32-bit CMT0 device included in r8a774c0. + - "renesas,r8a774c0-cmt1" for the 48-bit CMT1 device included in r8a774c0. - "renesas,r8a7790-cmt0" for the 32-bit CMT0 device included in r8a7790. - "renesas,r8a7790-cmt1" for the 48-bit CMT1 device included in r8a7790. - "renesas,r8a7791-cmt0" for the 32-bit CMT0 device included in r8a7791. diff --git a/Documentation/devicetree/bindings/timer/renesas,tmu.txt b/Documentation/devicetree/bindings/timer/renesas,tmu.txt index 4ddff85837da..13ad07416bdd 100644 --- a/Documentation/devicetree/bindings/timer/renesas,tmu.txt +++ b/Documentation/devicetree/bindings/timer/renesas,tmu.txt @@ -10,6 +10,7 @@ Required Properties: - compatible: must contain one or more of the following: - "renesas,tmu-r8a7740" for the r8a7740 TMU + - "renesas,tmu-r8a774c0" for the r8a774C0 TMU - "renesas,tmu-r8a7778" for the r8a7778 TMU - "renesas,tmu-r8a7779" for the r8a7779 TMU - "renesas,tmu-r8a77970" for the r8a77970 TMU diff --git a/Documentation/devicetree/bindings/timer/socionext,milbeaut-timer.txt b/Documentation/devicetree/bindings/timer/socionext,milbeaut-timer.txt new file mode 100644 index 000000000000..ac44c4b67530 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/socionext,milbeaut-timer.txt @@ -0,0 +1,17 @@ +Milbeaut SoCs Timer Controller + +Required properties: + +- compatible : should be "socionext,milbeaut-timer". +- reg : Specifies base physical address and size of the registers. +- interrupts : The interrupt of the first timer. +- clocks: phandle to the input clk. + +Example: + +timer { + compatible = "socionext,milbeaut-timer"; + reg = <0x1e000050 0x20> + interrupts = <0 91 4>; + clocks = <&clk 4>; +}; diff --git a/Documentation/devicetree/bindings/trivial-devices.yaml b/Documentation/devicetree/bindings/trivial-devices.yaml index cc64ec63a6ad..d79fb22bde39 100644 --- a/Documentation/devicetree/bindings/trivial-devices.yaml +++ b/Documentation/devicetree/bindings/trivial-devices.yaml @@ -322,6 +322,8 @@ properties: - ti,ads7830 # Temperature Monitoring and Fan Control - ti,amc6821 + # Temperature sensor with integrated fan control + - ti,lm96000 # I2C Touch-Screen Controller - ti,tsc2003 # Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface diff --git a/Documentation/devicetree/bindings/ufs/ufs-hisi.txt b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt index a48c44817367..0b83df1a5418 100644 --- a/Documentation/devicetree/bindings/ufs/ufs-hisi.txt +++ b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt @@ -6,9 +6,10 @@ Each UFS Host Controller should have its own node. Required properties: - compatible : compatible list, contains one of the following - "hisilicon,hi3660-ufs", "jedec,ufs-1.1" for hisi ufs - host controller present on Hi36xx chipset. + host controller present on Hi3660 chipset. + "hisilicon,hi3670-ufs", "jedec,ufs-2.1" for hisi ufs + host controller present on Hi3670 chipset. - reg : should contain UFS register address space & UFS SYS CTRL register address, -- interrupt-parent : interrupt device - interrupts : interrupt number - clocks : List of phandle and clock specifier pairs - clock-names : List of clock input name strings sorted in the same diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt index 8cf59452c675..5111e9130bc3 100644 --- a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt +++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt @@ -4,11 +4,14 @@ UFSHC nodes are defined to describe on-chip UFS host controllers. Each UFS controller instance should have its own node. Required properties: -- compatible : must contain "jedec,ufs-1.1" or "jedec,ufs-2.0", may - also list one or more of the following: - "qcom,msm8994-ufshc" - "qcom,msm8996-ufshc" - "qcom,ufshc" +- compatible : must contain "jedec,ufs-1.1" or "jedec,ufs-2.0" + + For Qualcomm SoCs must contain, as below, an + SoC-specific compatible along with "qcom,ufshc" and + the appropriate jedec string: + "qcom,msm8994-ufshc", "qcom,ufshc", "jedec,ufs-2.0" + "qcom,msm8996-ufshc", "qcom,ufshc", "jedec,ufs-2.0" + "qcom,sdm845-ufshc", "qcom,ufshc", "jedec,ufs-2.0" - interrupts : <interrupt mapping for UFS host controller IRQ> - reg : <registers mapping> diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index adae82385dd6..a254386a91ad 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -93,6 +93,7 @@ i.mx specific properties - over-current-active-low: over current signal polarity is active low. - over-current-active-high: over current signal polarity is active high. It's recommended to specify the over current polarity. +- power-active-high: power signal polarity is active high - external-vbus-divider: enables off-chip resistor divider for Vbus Example: diff --git a/Documentation/devicetree/bindings/usb/ingenic,jz4740-musb.txt b/Documentation/devicetree/bindings/usb/ingenic,jz4740-musb.txt new file mode 100644 index 000000000000..620355cee63f --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ingenic,jz4740-musb.txt @@ -0,0 +1,24 @@ +Ingenic JZ4740 MUSB driver + +Required properties: + +- compatible: Must be "ingenic,jz4740-musb" +- reg: Address range of the UDC register set +- interrupts: IRQ number related to the UDC hardware +- interrupt-names: must be "mc" +- clocks: phandle to the "udc" clock +- clock-names: must be "udc" + +Example: + +udc: usb@13040000 { + compatible = "ingenic,jz4740-musb"; + reg = <0x13040000 0x10000>; + + interrupt-parent = <&intc>; + interrupts = <24>; + interrupt-names = "mc"; + + clocks = <&cgu JZ4740_CLK_UDC>; + clock-names = "udc"; +}; diff --git a/Documentation/devicetree/bindings/usb/keystone-usb.txt b/Documentation/devicetree/bindings/usb/keystone-usb.txt index f96e09f784cc..77df82e36138 100644 --- a/Documentation/devicetree/bindings/usb/keystone-usb.txt +++ b/Documentation/devicetree/bindings/usb/keystone-usb.txt @@ -3,7 +3,9 @@ TI Keystone Soc USB Controller DWC3 GLUE Required properties: - - compatible: should be "ti,keystone-dwc3". + - compatible: should be + "ti,keystone-dwc3" for Keystone 2 SoCs + "ti,am654-dwc3" for AM654 SoC - #address-cells, #size-cells : should be '1' if the device has sub-nodes with 'reg' property. - reg : Address and length of the register set for the USB subsystem on @@ -21,7 +23,7 @@ SoCs only: - clock-names: Must be "usb". -The following are mandatory properties for Keystone 2 66AK2G SoCs only: +The following are mandatory properties for 66AK2G and AM654: - power-domains: Should contain a phandle to a PM domain provider node and an args specifier containing the USB device id diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt index 95afdcf3c337..cb695aa3fba4 100644 --- a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt +++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt @@ -4,6 +4,7 @@ Required properties: - compatible: Compatible list, contains "qcom,dwc3" "qcom,msm8996-dwc3" for msm8996 SOC. + "qcom,msm8998-dwc3" for msm8998 SOC. "qcom,sdm845-dwc3" for sdm845 SOC. - reg: Offset and length of register set for QSCRATCH wrapper - power-domains: specifies a phandle to PM domain provider node diff --git a/Documentation/devicetree/bindings/usb/renesas_usb3.txt b/Documentation/devicetree/bindings/usb/renesas_usb3.txt index d366555166d0..35039e720515 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usb3.txt +++ b/Documentation/devicetree/bindings/usb/renesas_usb3.txt @@ -3,6 +3,7 @@ Renesas Electronics USB3.0 Peripheral driver Required properties: - compatible: Must contain one of the following: - "renesas,r8a774a1-usb3-peri" + - "renesas,r8a774c0-usb3-peri" - "renesas,r8a7795-usb3-peri" - "renesas,r8a7796-usb3-peri" - "renesas,r8a77965-usb3-peri" diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt index 90719f501852..d93b6a1504f2 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt +++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt @@ -7,6 +7,7 @@ Required properties: - "renesas,usbhs-r8a7744" for r8a7744 (RZ/G1N) compatible device - "renesas,usbhs-r8a7745" for r8a7745 (RZ/G1E) compatible device - "renesas,usbhs-r8a774a1" for r8a774a1 (RZ/G2M) compatible device + - "renesas,usbhs-r8a774c0" for r8a774c0 (RZ/G2E) compatible device - "renesas,usbhs-r8a7790" for r8a7790 (R-Car H2) compatible device - "renesas,usbhs-r8a7791" for r8a7791 (R-Car M2-W) compatible device - "renesas,usbhs-r8a7792" for r8a7792 (R-Car V2H) compatible device diff --git a/Documentation/devicetree/bindings/usb/usb251xb.txt b/Documentation/devicetree/bindings/usb/usb251xb.txt index 168ff819e827..17915f64b8ee 100644 --- a/Documentation/devicetree/bindings/usb/usb251xb.txt +++ b/Documentation/devicetree/bindings/usb/usb251xb.txt @@ -64,6 +64,8 @@ Optional properties : - power-on-time-ms : Specifies the time it takes from the time the host initiates the power-on sequence to a port until the port has adequate power. The value is given in ms in a 0 - 510 range (default is 100ms). + - swap-dx-lanes : Specifies the ports which will swap the differential-pair + (D+/D-), default is not-swapped. Examples: usb2512b@2c { @@ -81,4 +83,6 @@ Examples: manufacturer = "Foo"; product = "Foo-Bar"; serial = "1234567890A"; + /* correct misplaced usb connectors on port 1,2 */ + swap-dx-lanes = <1 2>; }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index cfb590f9849c..8162b0eb4b50 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -24,6 +24,7 @@ amarula Amarula Solutions amazon Amazon.com, Inc. amcc Applied Micro Circuits Corporation (APM, formally AMCC) amd Advanced Micro Devices (AMD), Inc. +amediatech Shenzhen Amediatech Technology Co., Ltd amlogic Amlogic, Inc. ampire Ampire Co., Ltd. ams AMS AG @@ -65,6 +66,7 @@ bticino Bticino International calxeda Calxeda capella Capella Microsystems, Inc cascoda Cascoda, Ltd. +catalyst Catalyst Semiconductor, Inc. cavium Cavium, Inc. cdns Cadence Design Systems Inc. cdtech CDTech(H.K.) Electronics Limited @@ -108,11 +110,13 @@ dongwoon Dongwoon Anatech dptechnics DPTechnics dragino Dragino Technology Co., Limited ea Embedded Artists AB +ebs-systart EBS-SYSTART GmbH ebv EBV Elektronik eckelmann Eckelmann AG edt Emerging Display Technologies eeti eGalax_eMPIA Technology Inc elan Elan Microelectronic Corp. +elgin Elgin S/A. embest Shenzhen Embest Technology Co., Ltd. emlid Emlid, Ltd. emmicro EM Microelectronic @@ -142,6 +146,7 @@ focaltech FocalTech Systems Co.,Ltd friendlyarm Guangzhou FriendlyARM Computer Tech Co., Ltd fsl Freescale Semiconductor fujitsu Fujitsu Ltd. +gateworks Gateworks Corporation gcw Game Consoles Worldwide ge General Electric Company geekbuying GeekBuying @@ -151,6 +156,7 @@ geniatech Geniatech, Inc. giantec Giantec Semiconductor, Inc. giantplus Giantplus Technology Co., Ltd. globalscale Globalscale Technologies, Inc. +globaltop GlobalTop Technology, Inc. gmt Global Mixed-mode Technology, Inc. goodix Shenzhen Huiding Technology Co., Ltd. google Google, Inc. @@ -212,6 +218,7 @@ laird Laird PLC lantiq Lantiq Semiconductor lattice Lattice Semiconductor lego LEGO Systems A/S +lemaker Shenzhen LeMaker Technology Co., Ltd. lenovo Lenovo Group Ltd. lg LG Corporation libretech Shenzhen Libre Technology Co., Ltd @@ -274,6 +281,7 @@ nintendo Nintendo nlt NLT Technologies, Ltd. nokia Nokia nordic Nordic Semiconductor +novtech NovTech, Inc. nutsboard NutsBoard nuvoton Nuvoton Technology Corporation nvd New Vision Display @@ -298,6 +306,7 @@ ovti OmniVision Technologies oxsemi Oxford Semiconductor, Ltd. panasonic Panasonic Corporation parade Parade Technologies Inc. +pda Precision Design Associates, Inc. pericom Pericom Technology Inc. pervasive Pervasive Displays, Inc. phicomm PHICOMM Co., Ltd. @@ -305,6 +314,7 @@ phytec PHYTEC Messtechnik GmbH picochip Picochip Ltd pine64 Pine64 pixcir PIXCIR MICROELECTRONICS Co., Ltd +plantower Plantower Co., Ltd plathome Plat'Home Co., Ltd. plda PLDA plx Broadcom Corporation (formerly PLX Technology) @@ -432,6 +442,7 @@ vot Vision Optical Technology Co., Ltd. wd Western Digital Corp. wetek WeTek Electronics, limited. wexler Wexler +whwave Shenzhen whwave Electronics, Inc. wi2wi Wi2Wi, Inc. winbond Winbond Electronics corp. winstar Winstar Display Corp. diff --git a/Documentation/devicetree/bindings/watchdog/st,stpmic1-wdt.txt b/Documentation/devicetree/bindings/watchdog/st,stpmic1-wdt.txt new file mode 100644 index 000000000000..7cc1407f15cb --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/st,stpmic1-wdt.txt @@ -0,0 +1,11 @@ +STMicroelectronics STPMIC1 Watchdog + +Required properties: + +- compatible : should be "st,stpmic1-wdt" + +Example: + +watchdog { + compatible = "st,stpmic1-wdt"; +}; |