diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
13 files changed, 295 insertions, 86 deletions
diff --git a/Documentation/devicetree/bindings/arm/marvell/cp110-system-controller0.txt b/Documentation/devicetree/bindings/arm/marvell/cp110-system-controller0.txt index 30c546900b60..07dbb358182c 100644 --- a/Documentation/devicetree/bindings/arm/marvell/cp110-system-controller0.txt +++ b/Documentation/devicetree/bindings/arm/marvell/cp110-system-controller0.txt @@ -45,7 +45,7 @@ The following clocks are available: - 1 15 SATA - 1 16 SATA USB - 1 17 Main - - 1 18 SD/MMC + - 1 18 SD/MMC/GOP - 1 21 Slow IO (SPI, NOR, BootROM, I2C, UART) - 1 22 USB3H0 - 1 23 USB3H1 @@ -65,7 +65,7 @@ Required properties: "cpm-audio", "cpm-communit", "cpm-nand", "cpm-ppv2", "cpm-sdio", "cpm-mg-domain", "cpm-mg-core", "cpm-xor1", "cpm-xor0", "cpm-gop-dp", "none", "cpm-pcie_x10", "cpm-pcie_x11", "cpm-pcie_x4", "cpm-pcie-xor", "cpm-sata", - "cpm-sata-usb", "cpm-main", "cpm-sd-mmc", "none", "none", "cpm-slow-io", + "cpm-sata-usb", "cpm-main", "cpm-sd-mmc-gop", "none", "none", "cpm-slow-io", "cpm-usb3h0", "cpm-usb3h1", "cpm-usb3dev", "cpm-eip150", "cpm-eip197"; Example: @@ -78,6 +78,6 @@ Example: gate-clock-output-names = "cpm-audio", "cpm-communit", "cpm-nand", "cpm-ppv2", "cpm-sdio", "cpm-mg-domain", "cpm-mg-core", "cpm-xor1", "cpm-xor0", "cpm-gop-dp", "none", "cpm-pcie_x10", "cpm-pcie_x11", "cpm-pcie_x4", "cpm-pcie-xor", "cpm-sata", - "cpm-sata-usb", "cpm-main", "cpm-sd-mmc", "none", "none", "cpm-slow-io", + "cpm-sata-usb", "cpm-main", "cpm-sd-mmc-gop", "none", "none", "cpm-slow-io", "cpm-usb3h0", "cpm-usb3h1", "cpm-usb3dev", "cpm-eip150", "cpm-eip197"; }; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt index a78265993665..ca5204b3bc21 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt @@ -4,7 +4,6 @@ Required properties: - compatible: value should be one of the following "samsung,exynos3250-mipi-dsi" /* for Exynos3250/3472 SoCs */ "samsung,exynos4210-mipi-dsi" /* for Exynos4 SoCs */ - "samsung,exynos4415-mipi-dsi" /* for Exynos4415 SoC */ "samsung,exynos5410-mipi-dsi" /* for Exynos5410/5420/5440 SoCs */ "samsung,exynos5422-mipi-dsi" /* for Exynos5422/5800 SoCs */ "samsung,exynos5433-mipi-dsi" /* for Exynos5433 SoCs */ diff --git a/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt b/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt index 18645e0228b0..5837402c3ade 100644 --- a/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt +++ b/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt @@ -11,7 +11,6 @@ Required properties: "samsung,s5pv210-fimd"; /* for S5PV210 SoC */ "samsung,exynos3250-fimd"; /* for Exynos3250/3472 SoCs */ "samsung,exynos4210-fimd"; /* for Exynos4 SoCs */ - "samsung,exynos4415-fimd"; /* for Exynos4415 SoC */ "samsung,exynos5250-fimd"; /* for Exynos5250 SoCs */ "samsung,exynos5420-fimd"; /* for Exynos5420/5422/5800 SoCs */ diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt index ea9c1c9607f6..520d61dad6dd 100644 --- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt @@ -13,7 +13,7 @@ Required Properties: - "rockchip,rk2928-dw-mshc": for Rockchip RK2928 and following, before RK3288 - "rockchip,rk3288-dw-mshc": for Rockchip RK3288 - - "rockchip,rk1108-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK1108 + - "rockchip,rv1108-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RV1108 - "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3036 - "rockchip,rk3368-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3368 - "rockchip,rk3399-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3399 diff --git a/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt b/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt index b7fa3b97986d..a339dbb15493 100644 --- a/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt +++ b/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt @@ -44,13 +44,19 @@ Hip05 Example (note that Hip06 is the same except compatible): }; HiSilicon Hip06/Hip07 PCIe host bridge DT (almost-ECAM) description. + +Some BIOSes place the host controller in a mode where it is ECAM +compliant for all devices other than the root complex. In such cases, +the host controller should be described as below. + The properties and their meanings are identical to those described in host-generic-pci.txt except as listed below. Properties of the host controller node that differ from host-generic-pci.txt: -- compatible : Must be "hisilicon,pcie-almost-ecam" +- compatible : Must be "hisilicon,hip06-pcie-ecam", or + "hisilicon,hip07-pcie-ecam" - reg : Two entries: First the ECAM configuration space for any other bus underneath the root bus. Second, the base @@ -59,7 +65,7 @@ host-generic-pci.txt: Example: pcie0: pcie@a0090000 { - compatible = "hisilicon,pcie-almost-ecam"; + compatible = "hisilicon,hip06-pcie-ecam"; reg = <0 0xb0000000 0 0x2000000>, /* ECAM configuration space */ <0 0xa0090000 0 0x10000>; /* host bridge registers */ bus-range = <0 31>; diff --git a/Documentation/devicetree/bindings/phy/brcm,nsp-usb3-phy.txt b/Documentation/devicetree/bindings/phy/brcm,nsp-usb3-phy.txt deleted file mode 100644 index e68ae5dec9c9..000000000000 --- a/Documentation/devicetree/bindings/phy/brcm,nsp-usb3-phy.txt +++ /dev/null @@ -1,39 +0,0 @@ -Broadcom USB3 phy binding for northstar plus SoC -The USB3 phy is internal to the SoC and is accessed using mdio interface. - -Required mdio bus properties: -- reg: Should be 0x0 for SoC internal USB3 phy -- #address-cells: must be 1 -- #size-cells: must be 0 - -Required USB3 PHY properties: -- compatible: should be "brcm,nsp-usb3-phy" -- reg: USB3 Phy address on SoC internal MDIO bus and it should be 0x10. -- usb3-ctrl-syscon: handler of syscon node defining physical address - of usb3 control register. -- #phy-cells: must be 0 - -Required usb3 control properties: -- compatible: should be "brcm,nsp-usb3-ctrl" -- reg: offset and length of the control registers - -Example: - - mdio@0 { - reg = <0x0>; - #address-cells = <1>; - #size-cells = <0>; - - usb3_phy: usb-phy@10 { - compatible = "brcm,nsp-usb3-phy"; - reg = <0x10>; - usb3-ctrl-syscon = <&usb3_ctrl>; - #phy-cells = <0>; - status = "disabled"; - }; - }; - - usb3_ctrl: syscon@104408 { - compatible = "brcm,nsp-usb3-ctrl", "syscon"; - reg = <0x104408 0x3fc>; - }; diff --git a/Documentation/devicetree/bindings/powerpc/4xx/emac.txt b/Documentation/devicetree/bindings/powerpc/4xx/emac.txt index 712baf6c3e24..44b842b6ca15 100644 --- a/Documentation/devicetree/bindings/powerpc/4xx/emac.txt +++ b/Documentation/devicetree/bindings/powerpc/4xx/emac.txt @@ -71,6 +71,9 @@ For Axon it can be absent, though my current driver doesn't handle phy-address yet so for now, keep 0x00ffffff in it. + - phy-handle : Used to describe configurations where a external PHY + is used. Please refer to: + Documentation/devicetree/bindings/net/ethernet.txt - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec operations (if absent the value is the same as rx-fifo-size). For Axon, either absent or 2048. @@ -81,8 +84,22 @@ offload, phandle of the TAH device node. - tah-channel : 1 cell, optional. If appropriate, channel used on the TAH engine. + - fixed-link : Fixed-link subnode describing a link to a non-MDIO + managed entity. See + Documentation/devicetree/bindings/net/fixed-link.txt + for details. + - mdio subnode : When the EMAC has a phy connected to its local + mdio, which us supported by the kernel's network + PHY library in drivers/net/phy, there must be device + tree subnode with the following required properties: + - #address-cells: Must be <1>. + - #size-cells: Must be <0>. - Example: + For PHY definitions: Please refer to + Documentation/devicetree/bindings/net/phy.txt and + Documentation/devicetree/bindings/net/ethernet.txt + + Examples: EMAC0: ethernet@40000800 { device_type = "network"; @@ -104,6 +121,48 @@ zmii-channel = <0>; }; + EMAC1: ethernet@ef600c00 { + device_type = "network"; + compatible = "ibm,emac-apm821xx", "ibm,emac4sync"; + interrupt-parent = <&EMAC1>; + interrupts = <0 1>; + #interrupt-cells = <1>; + #address-cells = <0>; + #size-cells = <0>; + interrupt-map = <0 &UIC2 0x10 IRQ_TYPE_LEVEL_HIGH /* Status */ + 1 &UIC2 0x14 IRQ_TYPE_LEVEL_HIGH /* Wake */>; + reg = <0xef600c00 0x000000c4>; + local-mac-address = [000000000000]; /* Filled in by U-Boot */ + mal-device = <&MAL0>; + mal-tx-channel = <0>; + mal-rx-channel = <0>; + cell-index = <0>; + max-frame-size = <9000>; + rx-fifo-size = <16384>; + tx-fifo-size = <2048>; + fifo-entry-size = <10>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + phy-map = <0x00000000>; + rgmii-device = <&RGMII0>; + rgmii-channel = <0>; + tah-device = <&TAH0>; + tah-channel = <0>; + has-inverted-stacr-oc; + has-new-stacr-staopc; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + }; + }; + + ii) McMAL node Required properties: @@ -145,4 +204,3 @@ - revision : as provided by the RGMII new version register if available. For Axon: 0x0000012a - diff --git a/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt index c3f6546ebac7..6a23ad9ac53a 100644 --- a/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt @@ -45,7 +45,7 @@ Required Properties: Optional Properties: - reg-names: In addition to the required properties, the following are optional - "efuse-address" - Contains efuse base address used to pick up ABB info. - - "ldo-address" - Contains address of ABB LDO overide register address. + - "ldo-address" - Contains address of ABB LDO override register. "efuse-address" is required for this. - ti,ldovbb-vset-mask - Required if ldo-address is set, mask for LDO override register to provide override vset value. diff --git a/Documentation/devicetree/bindings/rng/omap_rng.txt b/Documentation/devicetree/bindings/rng/omap_rng.txt index 471477299ece..9cf7876ab434 100644 --- a/Documentation/devicetree/bindings/rng/omap_rng.txt +++ b/Documentation/devicetree/bindings/rng/omap_rng.txt @@ -12,7 +12,8 @@ Required properties: - reg : Offset and length of the register set for the module - interrupts : the interrupt number for the RNG module. Used for "ti,omap4-rng" and "inside-secure,safexcel-eip76" -- clocks: the trng clock source +- clocks: the trng clock source. Only mandatory for the + "inside-secure,safexcel-eip76" compatible. Example: /* AM335x */ diff --git a/Documentation/devicetree/bindings/sound/cs35l35.txt b/Documentation/devicetree/bindings/sound/cs35l35.txt new file mode 100644 index 000000000000..016b768bc722 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs35l35.txt @@ -0,0 +1,180 @@ +CS35L35 Boosted Speaker Amplifier + +Required properties: + + - compatible : "cirrus,cs35l35" + + - reg : the I2C address of the device for I2C + + - VA-supply, VP-supply : power supplies for the device, + as covered in + Documentation/devicetree/bindings/regulator/regulator.txt. + + - interrupt-parent : Specifies the phandle of the interrupt controller to + which the IRQs from CS35L35 are delivered to. + - interrupts : IRQ line info CS35L35. + (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + for further information relating to interrupt properties) + +Optional properties: + - reset-gpios : gpio used to reset the amplifier + + - cirrus,stereo-config : Boolean to determine if there are 2 AMPs for a + Stereo configuration + + - cirrus,audio-channel : Set Location of Audio Signal on Serial Port + 0 = Data Packet received on Left I2S Channel + 1 = Data Packet received on Right I2S Channel + + - cirrus,advisory-channel : Set Location of Advisory Signal on Serial Port + 0 = Data Packet received on Left I2S Channel + 1 = Data Packet received on Right I2S Channel + + - cirrus,shared-boost : Boolean to enable ClassH tracking of Advisory Signal + if 2 Devices share Boost BST_CTL + + - cirrus,external-boost : Boolean to specify the device is using an external + boost supply, note that sharing a boost from another cs35l35 would constitute + using an external supply for the slave device + + - cirrus,sp-drv-strength : Value for setting the Serial Port drive strength + Table 3-10 of the datasheet lists drive-strength specifications + 0 = 1x (Default) + 1 = .5x + - cirrus,sp-drv-unused : Determines how unused slots should be driven on the + Serial Port. + 0 - Hi-Z + 2 - Drive 0's (Default) + 3 - Drive 1's + + - cirrus,bst-pdn-fet-on : Boolean to determine if the Boost PDN control + powers down with a rectification FET On or Off. If VSPK is supplied + externally then FET is off. + + - cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost + converter's output voltage in mV. The range is from 2600mV to 9000mV with + increments of 100mV. + (Default) VP + + - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA. + Configures the peak current by monitoring the current through the boost FET. + Range starts at 1680mA and goes to a maximum of 4480mA with increments of + 110mA. + (Default) 2.46 Amps + + - cirrus,amp-gain-zc : Boolean to determine if to use Amplifier gain-change + zero-cross + +Optional H/G Algorithm sub-node: + + The cs35l35 node can have a single "cirrus,classh-internal-algo" sub-node + that will disable automatic control of the internal H/G Algorithm. + + It is strongly recommended that the Datasheet be referenced when adjusting + or using these Class H Algorithm controls over the internal Algorithm. + Serious damage can occur to the Device and surrounding components. + + - cirrus,classh-internal-algo : Sub-node for the Internal Class H Algorithm + See Section 4.3 Internal Class H Algorithm in the Datasheet. + If not used, the device manages the ClassH Algorithm internally. + +Optional properties for the "cirrus,classh-internal-algo" Sub-node + + Section 7.29 Class H Control + - cirrus,classh-bst-overide : Boolean + - cirrus,classh-bst-max-limit + - cirrus,classh-mem-depth + + Section 7.30 Class H Headroom Control + - cirrus,classh-headroom + + Section 7.31 Class H Release Rate + - cirrus,classh-release-rate + + Section 7.32 Class H Weak FET Drive Control + - cirrus,classh-wk-fet-disable + - cirrus,classh-wk-fet-delay + - cirrus,classh-wk-fet-thld + + Section 7.34 Class H VP Control + - cirrus,classh-vpch-auto + - cirrus,classh-vpch-rate + - cirrus,classh-vpch-man + +Optional Monitor Signal Format sub-node: + + The cs35l35 node can have a single "cirrus,monitor-signal-format" sub-node + for adjusting the Depth, Location and Frame of the Monitoring Signals + for Algorithms. + + See Sections 4.8.2 through 4.8.4 Serial-Port Control in the Datasheet + + -cirrus,monitor-signal-format : Sub-node for the Monitor Signaling Formating + on the I2S Port. Each of the 3 8 bit values in the array contain the settings + for depth, location, and frame. + + If not used, the defaults for the 6 monitor signals is used. + + Sections 7.44 - 7.53 lists values for the depth, location, and frame + for each monitoring signal. + + - cirrus,imon : 4 8 bit values to set the depth, location, frame and ADC + scale of the IMON monitor signal. + + - cirrus,vmon : 3 8 bit values to set the depth, location, and frame + of the VMON monitor signal. + + - cirrus,vpmon : 3 8 bit values to set the depth, location, and frame + of the VPMON monitor signal. + + - cirrus,vbstmon : 3 8 bit values to set the depth, location, and frame + of the VBSTMON monitor signal + + - cirrus,vpbrstat : 3 8 bit values to set the depth, location, and frame + of the VPBRSTAT monitor signal + + - cirrus,zerofill : 3 8 bit values to set the depth, location, and frame\ + of the ZEROFILL packet in the monitor signal + +Example: + +cs35l35: cs35l35@20 { + compatible = "cirrus,cs35l35"; + reg = <0x20>; + VA-supply = <&dummy_vreg>; + VP-supply = <&dummy_vreg>; + reset-gpios = <&axi_gpio 54 0>; + interrupt-parent = <&gpio8>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + cirrus,boost-ctl-millivolt = <9000>; + + cirrus,stereo-config; + cirrus,audio-channel = <0x00>; + cirrus,advisory-channel = <0x01>; + cirrus,shared-boost; + + cirrus,classh-internal-algo { + cirrus,classh-bst-overide; + cirrus,classh-bst-max-limit = <0x01>; + cirrus,classh-mem-depth = <0x01>; + cirrus,classh-release-rate = <0x08>; + cirrus,classh-headroom-millivolt = <0x0B>; + cirrus,classh-wk-fet-disable = <0x01>; + cirrus,classh-wk-fet-delay = <0x04>; + cirrus,classh-wk-fet-thld = <0x01>; + cirrus,classh-vpch-auto = <0x01>; + cirrus,classh-vpch-rate = <0x02>; + cirrus,classh-vpch-man = <0x05>; + }; + + /* Depth, Location, Frame */ + cirrus,monitor-signal-format { + cirrus,imon = /bits/ 8 <0x03 0x00 0x01>; + cirrus,vmon = /bits/ 8 <0x03 0x00 0x00>; + cirrus,vpmon = /bits/ 8 <0x03 0x04 0x00>; + cirrus,vbstmon = /bits/ 8 <0x03 0x04 0x01>; + cirrus,vpbrstat = /bits/ 8 <0x00 0x04 0x00>; + cirrus,zerofill = /bits/ 8 <0x00 0x00 0x00>; + }; + +}; diff --git a/Documentation/devicetree/bindings/sound/dioo,dio2125.txt b/Documentation/devicetree/bindings/sound/dioo,dio2125.txt new file mode 100644 index 000000000000..63dbfe0f11d0 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/dioo,dio2125.txt @@ -0,0 +1,12 @@ +DIO2125 Audio Driver + +Required properties: +- compatible : "dioo,dio2125" +- enable-gpios : the gpio connected to the enable pin of the dio2125 + +Example: + +amp: analog-amplifier { + compatible = "dioo,dio2125"; + enable-gpios = <&gpio GPIOH_3 0>; +}; diff --git a/Documentation/devicetree/bindings/sound/everest,es7134.txt b/Documentation/devicetree/bindings/sound/everest,es7134.txt new file mode 100644 index 000000000000..5495a3cb8b7b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/everest,es7134.txt @@ -0,0 +1,10 @@ +ES7134 i2s DA converter + +Required properties: +- compatible : "everest,es7134" or "everest,es7144" + +Example: + +i2s_codec: external-codec { + compatible = "everest,es7134"; +}; diff --git a/Documentation/devicetree/bindings/usb/usb251xb.txt b/Documentation/devicetree/bindings/usb/usb251xb.txt index 0c065f77658f..3957d4edaa74 100644 --- a/Documentation/devicetree/bindings/usb/usb251xb.txt +++ b/Documentation/devicetree/bindings/usb/usb251xb.txt @@ -7,18 +7,18 @@ Required properties : - compatible : Should be "microchip,usb251xb" or one of the specific types: "microchip,usb2512b", "microchip,usb2512bi", "microchip,usb2513b", "microchip,usb2513bi", "microchip,usb2514b", "microchip,usb2514bi" - - hub-reset-gpios : Should specify the gpio for hub reset + - reset-gpios : Should specify the gpio for hub reset + - reg : I2C address on the selected bus (default is <0x2C>) Optional properties : - - reg : I2C address on the selected bus (default is <0x2C>) - skip-config : Skip Hub configuration, but only send the USB-Attach command - - vendor-id : USB Vendor ID of the hub (16 bit, default is 0x0424) - - product-id : USB Product ID of the hub (16 bit, default depends on type) - - device-id : USB Device ID of the hub (16 bit, default is 0x0bb3) - - language-id : USB Language ID (16 bit, default is 0x0000) - - manufacturer : USB Manufacturer string (max 31 characters long) - - product : USB Product string (max 31 characters long) - - serial : USB Serial string (max 31 characters long) + - vendor-id : Set USB Vendor ID of the hub (16 bit, default is 0x0424) + - product-id : Set USB Product ID of the hub (16 bit, default depends on type) + - device-id : Set USB Device ID of the hub (16 bit, default is 0x0bb3) + - language-id : Set USB Language ID (16 bit, default is 0x0000) + - manufacturer : Set USB Manufacturer string (max 31 characters long) + - product : Set USB Product string (max 31 characters long) + - serial : Set USB Serial string (max 31 characters long) - {bus,self}-powered : selects between self- and bus-powered operation (default is self-powered) - disable-hi-speed : disable USB Hi-Speed support @@ -31,8 +31,10 @@ Optional properties : (default is individual) - dynamic-power-switching : enable auto-switching from self- to bus-powered operation if the local power source is removed or unavailable - - oc-delay-{100us,4ms,8ms,16ms} : set over current timer delay (default is 8ms) - - compound-device : indicated the hub is part of a compound device + - oc-delay-us : Delay time (in microseconds) for filtering the over-current + sense inputs. Valid values are 100, 4000, 8000 (default) and 16000. If + an invalid value is given, the default is used instead. + - compound-device : indicate the hub is part of a compound device - port-mapping-mode : enable port mapping mode - string-support : enable string descriptor support (required for manufacturer, product and serial string configuration) @@ -40,34 +42,15 @@ Optional properties : device connected. - sp-disabled-ports : Specifies the ports which will be self-power disabled - bp-disabled-ports : Specifies the ports which will be bus-power disabled - - max-sp-power : Specifies the maximum current the hub consumes from an - upstream port when operating as self-powered hub including the power - consumption of a permanently attached peripheral if the hub is - configured as a compound device. The value is given in mA in a 0 - 500 - range (default is 2). - - max-bp-power : Specifies the maximum current the hub consumes from an - upstream port when operating as bus-powered hub including the power - consumption of a permanently attached peripheral if the hub is - configured as a compound device. The value is given in mA in a 0 - 500 - range (default is 100). - - max-sp-current : Specifies the maximum current the hub consumes from an - upstream port when operating as self-powered hub EXCLUDING the power - consumption of a permanently attached peripheral if the hub is - configured as a compound device. The value is given in mA in a 0 - 500 - range (default is 2). - - max-bp-current : Specifies the maximum current the hub consumes from an - upstream port when operating as bus-powered hub EXCLUDING the power - consumption of a permanently attached peripheral if the hub is - configured as a compound device. The value is given in mA in a 0 - 500 - range (default is 100). - - power-on-time : Specifies the time it takes from the time the host initiates - the power-on sequence to a port until the port has adequate power. The - value is given in ms in a 0 - 510 range (default is 100ms). + - power-on-time-ms : Specifies the time it takes from the time the host + initiates the power-on sequence to a port until the port has adequate + power. The value is given in ms in a 0 - 510 range (default is 100ms). Examples: usb2512b@2c { compatible = "microchip,usb2512b"; - hub-reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + reg = <0x2c>; + reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; }; usb2514b@2c { |