diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
158 files changed, 3604 insertions, 638 deletions
diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt b/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt index b545856a444f..4a1714f96bab 100644 --- a/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt +++ b/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt @@ -90,6 +90,47 @@ Required Properties: - interrupts : Should be single bit error interrupt, then double bit error interrupt, in this order. +NAND FIFO ECC +Required Properties: +- compatible : Should be "altr,socfpga-nand-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent NAND node. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt, in this order. + +DMA FIFO ECC +Required Properties: +- compatible : Should be "altr,socfpga-dma-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent DMA node. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt, in this order. + +USB FIFO ECC +Required Properties: +- compatible : Should be "altr,socfpga-usb-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent USB node. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt, in this order. + +QSPI FIFO ECC +Required Properties: +- compatible : Should be "altr,socfpga-qspi-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent QSPI node. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt, in this order. + +SDMMC FIFO ECC +Required Properties: +- compatible : Should be "altr,socfpga-sdmmc-ecc" +- reg : Address and size for ECC block registers. +- altr,ecc-parent : phandle to parent SD/MMC node. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt, in this order for port A, and then single bit error interrupt, + then double bit error interrupt in this order for port B. + Example: eccmgr: eccmgr@ffd06000 { @@ -132,4 +173,61 @@ Example: interrupts = <5 IRQ_TYPE_LEVEL_HIGH>, <37 IRQ_TYPE_LEVEL_HIGH>; }; + + nand-buf-ecc@ff8c2000 { + compatible = "altr,socfpga-nand-ecc"; + reg = <0xff8c2000 0x400>; + altr,ecc-parent = <&nand>; + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>, + <43 IRQ_TYPE_LEVEL_HIGH>; + }; + + nand-rd-ecc@ff8c2400 { + compatible = "altr,socfpga-nand-ecc"; + reg = <0xff8c2400 0x400>; + altr,ecc-parent = <&nand>; + interrupts = <13 IRQ_TYPE_LEVEL_HIGH>, + <45 IRQ_TYPE_LEVEL_HIGH>; + }; + + nand-wr-ecc@ff8c2800 { + compatible = "altr,socfpga-nand-ecc"; + reg = <0xff8c2800 0x400>; + altr,ecc-parent = <&nand>; + interrupts = <12 IRQ_TYPE_LEVEL_HIGH>, + <44 IRQ_TYPE_LEVEL_HIGH>; + }; + + dma-ecc@ff8c8000 { + compatible = "altr,socfpga-dma-ecc"; + reg = <0xff8c8000 0x400>; + altr,ecc-parent = <&pdma>; + interrupts = <10 IRQ_TYPE_LEVEL_HIGH>, + <42 IRQ_TYPE_LEVEL_HIGH>; + + usb0-ecc@ff8c8800 { + compatible = "altr,socfpga-usb-ecc"; + reg = <0xff8c8800 0x400>; + altr,ecc-parent = <&usb0>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>, + <34 IRQ_TYPE_LEVEL_HIGH>; + }; + + qspi-ecc@ff8c8400 { + compatible = "altr,socfpga-qspi-ecc"; + reg = <0xff8c8400 0x400>; + altr,ecc-parent = <&qspi>; + interrupts = <14 IRQ_TYPE_LEVEL_HIGH>, + <46 IRQ_TYPE_LEVEL_HIGH>; + }; + + sdmmc-ecc@ff8c2c00 { + compatible = "altr,socfpga-sdmmc-ecc"; + reg = <0xff8c2c00 0x400>; + altr,ecc-parent = <&mmc>; + interrupts = <15 IRQ_TYPE_LEVEL_HIGH>, + <47 IRQ_TYPE_LEVEL_HIGH>, + <16 IRQ_TYPE_LEVEL_HIGH>, + <48 IRQ_TYPE_LEVEL_HIGH>; + }; }; diff --git a/Documentation/devicetree/bindings/arm/arch_timer.txt b/Documentation/devicetree/bindings/arm/arch_timer.txt index e774128935d5..ef5fbe9a77c7 100644 --- a/Documentation/devicetree/bindings/arm/arch_timer.txt +++ b/Documentation/devicetree/bindings/arm/arch_timer.txt @@ -25,6 +25,12 @@ to deliver its interrupts via SPIs. - always-on : a boolean property. If present, the timer is powered through an always-on power domain, therefore it never loses context. +- fsl,erratum-a008585 : A boolean property. Indicates the presence of + QorIQ erratum A-008585, which says that reading the counter is + unreliable unless the same value is returned by back-to-back reads. + This also affects writes to the tval register, due to the implicit + counter read. + ** Optional properties: - arm,cpu-registers-not-fw-configured : Firmware does not initialize diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt index 936166fbee09..cb0054ac7121 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt @@ -5,7 +5,8 @@ The Mediatek apmixedsys controller provides the PLLs to the system. Required Properties: -- compatible: Should be: +- compatible: Should be one of: + - "mediatek,mt2701-apmixedsys" - "mediatek,mt8135-apmixedsys" - "mediatek,mt8173-apmixedsys" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt new file mode 100644 index 000000000000..4137196dd686 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt @@ -0,0 +1,22 @@ +Mediatek bdpsys controller +============================ + +The Mediatek bdpsys controller provides various clocks to the system. + +Required Properties: + +- compatible: Should be: + - "mediatek,mt2701-bdpsys", "syscon" +- #clock-cells: Must be 1 + +The bdpsys controller uses the common clk binding from +Documentation/devicetree/bindings/clock/clock-bindings.txt +The available clocks are defined in dt-bindings/clock/mt*-clk.h. + +Example: + +bdpsys: clock-controller@1c000000 { + compatible = "mediatek,mt2701-bdpsys", "syscon"; + reg = <0 0x1c000000 0 0x1000>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt new file mode 100644 index 000000000000..768f3a5bc055 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt @@ -0,0 +1,22 @@ +Mediatek ethsys controller +============================ + +The Mediatek ethsys controller provides various clocks to the system. + +Required Properties: + +- compatible: Should be: + - "mediatek,mt2701-ethsys", "syscon" +- #clock-cells: Must be 1 + +The ethsys controller uses the common clk binding from +Documentation/devicetree/bindings/clock/clock-bindings.txt +The available clocks are defined in dt-bindings/clock/mt*-clk.h. + +Example: + +ethsys: clock-controller@1b000000 { + compatible = "mediatek,mt2701-ethsys", "syscon"; + reg = <0 0x1b000000 0 0x1000>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt new file mode 100644 index 000000000000..beed7b594cea --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt @@ -0,0 +1,24 @@ +Mediatek hifsys controller +============================ + +The Mediatek hifsys controller provides various clocks and reset +outputs to the system. + +Required Properties: + +- compatible: Should be: + - "mediatek,mt2701-hifsys", "syscon" +- #clock-cells: Must be 1 + +The hifsys controller uses the common clk binding from +Documentation/devicetree/bindings/clock/clock-bindings.txt +The available clocks are defined in dt-bindings/clock/mt*-clk.h. + +Example: + +hifsys: clock-controller@1a000000 { + compatible = "mediatek,mt2701-hifsys", "syscon"; + reg = <0 0x1a000000 0 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt index b1f2ce17dff8..f6a916686f4c 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt @@ -5,7 +5,8 @@ The Mediatek imgsys controller provides various clocks to the system. Required Properties: -- compatible: Should be: +- compatible: Should be one of: + - "mediatek,mt2701-imgsys", "syscon" - "mediatek,mt8173-imgsys", "syscon" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt index aaf8d1460c4d..1620ec2a5a3f 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt @@ -6,7 +6,8 @@ outputs to the system. Required Properties: -- compatible: Should be: +- compatible: Should be one of: + - "mediatek,mt2701-infracfg", "syscon" - "mediatek,mt8135-infracfg", "syscon" - "mediatek,mt8173-infracfg", "syscon" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt index 4385946eadef..67dd2e473d25 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt @@ -5,7 +5,8 @@ The Mediatek mmsys controller provides various clocks to the system. Required Properties: -- compatible: Should be: +- compatible: Should be one of: + - "mediatek,mt2701-mmsys", "syscon" - "mediatek,mt8173-mmsys", "syscon" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt index 2f6ff86df49f..e494366782aa 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt @@ -6,7 +6,8 @@ outputs to the system. Required Properties: -- compatible: Should be: +- compatible: Should be one of: + - "mediatek,mt2701-pericfg", "syscon" - "mediatek,mt8135-pericfg", "syscon" - "mediatek,mt8173-pericfg", "syscon" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt index f9e917994ced..9f2fe7860114 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt @@ -5,7 +5,8 @@ The Mediatek topckgen controller provides various clocks to the system. Required Properties: -- compatible: Should be: +- compatible: Should be one of: + - "mediatek,mt2701-topckgen" - "mediatek,mt8135-topckgen" - "mediatek,mt8173-topckgen" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt index 1faacf1c1b25..2440f73450c3 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt @@ -5,7 +5,8 @@ The Mediatek vdecsys controller provides various clocks to the system. Required Properties: -- compatible: Should be: +- compatible: Should be one of: + - "mediatek,mt2701-vdecsys", "syscon" - "mediatek,mt8173-vdecsys", "syscon" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt b/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt new file mode 100644 index 000000000000..a55d31b48d6e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt @@ -0,0 +1,45 @@ +* Amlogic GXBB AO Clock and Reset Unit + +The Amlogic GXBB AO clock controller generates and supplies clock to various +controllers within the Always-On part of the SoC. + +Required Properties: + +- compatible: should be "amlogic,gxbb-aoclkc" +- reg: physical base address of the clock controller and length of memory + mapped region. + +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/gxbb-aoclkc.h header and can be +used in device tree sources. + +- #reset-cells: should be 1. + +Each reset is assigned an identifier and client nodes can use this identifier +to specify the reset which they consume. All available resets are defined as +preprocessor macros in the dt-bindings/reset/gxbb-aoclkc.h header and can be +used in device tree sources. + +Example: AO Clock controller node: + + clkc_AO: clock-controller@040 { + compatible = "amlogic,gxbb-aoclkc"; + reg = <0x0 0x040 0x0 0x4>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock and reset generated + by the clock controller: + + uart_AO: serial@4c0 { + compatible = "amlogic,meson-uart"; + reg = <0x4c0 0x14>; + interrupts = <0 90 1>; + clocks = <&clkc_AO CLKID_AO_UART1>; + resets = <&clkc_AO RESET_AO_UART1>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/arm-syscon-icst.txt b/Documentation/devicetree/bindings/clock/arm-syscon-icst.txt index 8b7177cecb36..27468119fd94 100644 --- a/Documentation/devicetree/bindings/clock/arm-syscon-icst.txt +++ b/Documentation/devicetree/bindings/clock/arm-syscon-icst.txt @@ -5,20 +5,50 @@ Technology (IDT). ARM integrated these oscillators deeply into their reference designs by adding special control registers that manage such oscillators to their system controllers. -The ARM system controller contains logic to serialize and initialize +The various ARM system controllers contain logic to serialize and initialize an ICST clock request after a write to the 32 bit register at an offset into the system controller. Furthermore, to even be able to alter one of these frequencies, the system controller must first be unlocked by writing a special token to another offset in the system controller. +Some ARM hardware contain special versions of the serial interface that only +connects the low 8 bits of the VDW (missing one bit), hardwires RDW to +different values and sometimes also hardwire the output divider. They +therefore have special compatible strings as per this table (the OD value is +the value on the pins, not the resulting output divider): + +Hardware variant: RDW OD VDW + +Integrator/AP 22 1 Bit 8 0, rest variable +integratorap-cm + +Integrator/AP 46 3 Bit 8 0, rest variable +integratorap-sys + +Integrator/AP 22 or 1 17 or (33 or 25 MHz) +integratorap-pci 14 1 14 + +Integrator/CP 22 variable Bit 8 0, rest variable +integratorcp-cm-core + +Integrator/CP 22 variable Bit 8 0, rest variable +integratorcp-cm-mem + The ICST oscillator must be provided inside a system controller node. Required properties: +- compatible: must be one of + "arm,syscon-icst525" + "arm,syscon-icst307" + "arm,syscon-icst525-integratorap-cm" + "arm,syscon-icst525-integratorap-sys" + "arm,syscon-icst525-integratorap-pci" + "arm,syscon-icst525-integratorcp-cm-core" + "arm,syscon-icst525-integratorcp-cm-mem" - lock-offset: the offset address into the system controller where the unlocking register is located - vco-offset: the offset address into the system controller where the ICST control register is located (even 32 bit address) -- compatible: must be one of "arm,syscon-icst525" or "arm,syscon-icst307" - #clock-cells: must be <0> - clocks: parent clock, since the ICST needs a parent clock to derive its frequency from, this attribute is compulsory. diff --git a/Documentation/devicetree/bindings/clock/armada3700-periph-clock.txt b/Documentation/devicetree/bindings/clock/armada3700-periph-clock.txt new file mode 100644 index 000000000000..1e3370ba189f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/armada3700-periph-clock.txt @@ -0,0 +1,70 @@ +* Peripheral Clock bindings for Marvell Armada 37xx SoCs + +Marvell Armada 37xx SoCs provide peripheral clocks which are +used as clock source for the peripheral of the SoC. + +There are two different blocks associated to north bridge and south +bridge. + +The peripheral clock consumer should specify the desired clock by +having the clock ID in its "clocks" phandle cell. + +The following is a list of provided IDs for Armada 370 North bridge clocks: +ID Clock name Description +----------------------------------- +0 mmc MMC controller +1 sata_host Sata Host +2 sec_at Security AT +3 sac_dap Security DAP +4 tsecm Security Engine +5 setm_tmx Serial Embedded Trace Module +6 avs Adaptive Voltage Scaling +7 sqf SPI +8 pwm PWM +9 i2c_2 I2C 2 +10 i2c_1 I2C 1 +11 ddr_phy DDR PHY +12 ddr_fclk DDR F clock +13 trace Trace +14 counter Counter +15 eip97 EIP 97 +16 cpu CPU + +The following is a list of provided IDs for Armada 370 South bridge clocks: +ID Clock name Description +----------------------------------- +0 gbe-50 50 MHz parent clock for Gigabit Ethernet +1 gbe-core parent clock for Gigabit Ethernet core +2 gbe-125 125 MHz parent clock for Gigabit Ethernet +3 gbe1-50 50 MHz clock for Gigabit Ethernet port 1 +4 gbe0-50 50 MHz clock for Gigabit Ethernet port 0 +5 gbe1-125 125 MHz clock for Gigabit Ethernet port 1 +6 gbe0-125 125 MHz clock for Gigabit Ethernet port 0 +7 gbe1-core Gigabit Ethernet core port 1 +8 gbe0-core Gigabit Ethernet core port 0 +9 gbe-bm Gigabit Ethernet Buffer Manager +10 sdio SDIO +11 usb32-sub2-sys USB 2 clock +12 usb32-ss-sys USB 3 clock + +Required properties: + +- compatible : shall be "marvell,armada-3700-periph-clock-nb" for the + north bridge block, or + "marvell,armada-3700-periph-clock-sb" for the south bridge block +- reg : must be the register address of North/South Bridge Clock register +- #clock-cells : from common clock binding; shall be set to 1 + +- clocks : list of the parent clock phandle in the following order: + TBG-A P, TBG-B P, TBG-A S, TBG-B S and finally the xtal clock. + + +Example: + +nb_perih_clk: nb-periph-clk@13000{ + compatible = "marvell,armada-3700-periph-clock-nb"; + reg = <0x13000 0x1000>; + clocks = <&tbg 0>, <&tbg 1>, <&tbg 2>, + <&tbg 3>, <&xtalclk>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/armada3700-tbg-clock.txt b/Documentation/devicetree/bindings/clock/armada3700-tbg-clock.txt new file mode 100644 index 000000000000..0ba1d83ff363 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/armada3700-tbg-clock.txt @@ -0,0 +1,27 @@ +* Time Base Generator Clock bindings for Marvell Armada 37xx SoCs + +Marvell Armada 37xx SoCs provde Time Base Generator clocks which are +used as parent clocks for the peripheral clocks. + +The TBG clock consumer should specify the desired clock by having the +clock ID in its "clocks" phandle cell. + +The following is a list of provided IDs and clock names on Armada 3700: + 0 = TBG A P + 1 = TBG B P + 2 = TBG A S + 3 = TBG B S + +Required properties: +- compatible : shall be "marvell,armada-3700-tbg-clock" +- reg : must be the register address of North Bridge PLL register +- #clock-cells : from common clock binding; shall be set to 1 + +Example: + +tbg: tbg@13200 { + compatible = "marvell,armada-3700-tbg-clock"; + reg = <0x13200 0x1000>; + clocks = <&xtalclk>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/armada3700-xtal-clock.txt b/Documentation/devicetree/bindings/clock/armada3700-xtal-clock.txt new file mode 100644 index 000000000000..a88f1f05fbd6 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/armada3700-xtal-clock.txt @@ -0,0 +1,28 @@ +* Xtal Clock bindings for Marvell Armada 37xx SoCs + +Marvell Armada 37xx SoCs allow to determine the xtal clock frequencies by +reading the gpio latch register. + +This node must be a subnode of the node exposing the register address +of the GPIO block where the gpio latch is located. + +Required properties: +- compatible : shall be one of the following: + "marvell,armada-3700-xtal-clock" +- #clock-cells : from common clock binding; shall be set to 0 + +Optional properties: +- clock-output-names : from common clock binding; allows overwrite default clock + output names ("xtal") + +Example: +gpio1: gpio@13800 { + compatible = "marvell,armada-3700-gpio", "syscon", "simple-mfd"; + reg = <0x13800 0x1000>; + + xtalclk: xtal-clk { + compatible = "marvell,armada-3700-xtal-clock"; + clock-output-names = "xtal"; + #clock-cells = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt index 181bc8ac4e3a..5f3ad65daf69 100644 --- a/Documentation/devicetree/bindings/clock/at91-clock.txt +++ b/Documentation/devicetree/bindings/clock/at91-clock.txt @@ -6,7 +6,8 @@ This binding uses the common clock binding[1]. Required properties: - compatible : shall be one of the following: - "atmel,at91sam9x5-sckc": + "atmel,at91sam9x5-sckc" or + "atmel,sama5d4-sckc": at91 SCKC (Slow Clock Controller) This node contains the slow clock definitions. diff --git a/Documentation/devicetree/bindings/clock/brcm,bcm53573-ilp.txt b/Documentation/devicetree/bindings/clock/brcm,bcm53573-ilp.txt new file mode 100644 index 000000000000..2ebb107331dd --- /dev/null +++ b/Documentation/devicetree/bindings/clock/brcm,bcm53573-ilp.txt @@ -0,0 +1,36 @@ +Broadcom BCM53573 ILP clock +=========================== + +This binding uses the common clock binding: + Documentation/devicetree/bindings/clock/clock-bindings.txt + +This binding is used for ILP clock (sometimes referred as "slow clock") +on Broadcom BCM53573 devices using Cortex-A7 CPU. + +ILP's rate has to be calculated on runtime and it depends on ALP clock +which has to be referenced. + +This clock is part of PMU (Power Management Unit), a Broadcom's device +handing power-related aspects. Its node must be sub-node of the PMU +device. + +Required properties: +- compatible: "brcm,bcm53573-ilp" +- clocks: has to reference an ALP clock +- #clock-cells: should be <0> +- clock-output-names: from common clock bindings, should contain clock + name + +Example: + +pmu@18012000 { + compatible = "simple-mfd", "syscon"; + reg = <0x18012000 0x00001000>; + + ilp { + compatible = "brcm,bcm53573-ilp"; + clocks = <&alp>; + #clock-cells = <0>; + clock-output-names = "ilp"; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/clk-exynos-audss.txt b/Documentation/devicetree/bindings/clock/clk-exynos-audss.txt index 180e8835569e..0c3d6015868d 100644 --- a/Documentation/devicetree/bindings/clock/clk-exynos-audss.txt +++ b/Documentation/devicetree/bindings/clock/clk-exynos-audss.txt @@ -10,6 +10,8 @@ Required Properties: - "samsung,exynos4210-audss-clock" - controller compatible with all Exynos4 SoCs. - "samsung,exynos5250-audss-clock" - controller compatible with Exynos5250 SoCs. + - "samsung,exynos5410-audss-clock" - controller compatible with Exynos5410 + SoCs. - "samsung,exynos5420-audss-clock" - controller compatible with Exynos5420 SoCs. - reg: physical base address and length of the controller's register set. @@ -91,5 +93,5 @@ i2s0: i2s@03830000 { <&clock_audss EXYNOS_MOUT_AUDSS>, <&clock_audss EXYNOS_MOUT_I2S>; clock-names = "iis", "i2s_opclk0", "i2s_opclk1", - "mout_audss", "mout_i2s"; + "mout_audss", "mout_i2s"; }; diff --git a/Documentation/devicetree/bindings/clock/exynos5410-clock.txt b/Documentation/devicetree/bindings/clock/exynos5410-clock.txt index aeab635b07b5..4527de3ea205 100644 --- a/Documentation/devicetree/bindings/clock/exynos5410-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5410-clock.txt @@ -12,24 +12,29 @@ Required Properties: - #clock-cells: should be 1. +- clocks: should contain an entry specifying the root clock from external + oscillator supplied through XXTI or XusbXTI pin. This clock should be + defined using standard clock bindings with "fin_pll" clock-output-name. + That clock is being passed internally to the 9 PLLs. + All available clocks are defined as preprocessor macros in dt-bindings/clock/exynos5410.h header and can be used in device tree sources. -External clock: - -There is clock that is generated outside the SoC. It -is expected that it is defined using standard clock bindings -with following clock-output-name: - - - "fin_pll" - PLL input clock from XXTI - Example 1: An example of a clock controller node is listed below. + fin_pll: xxti { + compatible = "fixed-clock"; + clock-frequency = <24000000>; + clock-output-names = "fin_pll"; + #clock-cells = <0>; + }; + clock: clock-controller@0x10010000 { compatible = "samsung,exynos5410-clock"; reg = <0x10010000 0x30000>; #clock-cells = <1>; + clocks = <&fin_pll>; }; Example 2: UART controller node that consumes the clock generated by the clock diff --git a/Documentation/devicetree/bindings/clock/maxim,max77686.txt b/Documentation/devicetree/bindings/clock/maxim,max77686.txt index 9c40739a661a..8398a3a5e106 100644 --- a/Documentation/devicetree/bindings/clock/maxim,max77686.txt +++ b/Documentation/devicetree/bindings/clock/maxim,max77686.txt @@ -1,10 +1,24 @@ -Binding for Maxim MAX77686 32k clock generator block +Binding for Maxim MAX77686/MAX77802/MAX77620 32k clock generator block -This is a part of device tree bindings of MAX77686 multi-function device. -More information can be found in bindings/mfd/max77686.txt file. +This is a part of device tree bindings of MAX77686/MAX77802/MAX77620 +multi-function device. More information can be found in MFD DT binding +doc as follows: + bindings/mfd/max77686.txt for MAX77686 and + bindings/mfd/max77802.txt for MAX77802 and + bindings/mfd/max77620.txt for MAX77620. The MAX77686 contains three 32.768khz clock outputs that can be controlled -(gated/ungated) over I2C. +(gated/ungated) over I2C. Clocks are defined as preprocessor macros in +dt-bindings/clock/maxim,max77686.h. + + +The MAX77802 contains two 32.768khz clock outputs that can be controlled +(gated/ungated) over I2C. Clocks are defined as preprocessor macros in +dt-bindings/clock/maxim,max77802.h. + +The MAX77686 contains one 32.768khz clock outputs that can be controlled +(gated/ungated) over I2C. Clocks are defined as preprocessor macros in +dt-bindings/clock/maxim,max77620.h. Following properties should be presend in main device node of the MFD chip. @@ -17,30 +31,84 @@ Optional properties: Each clock is assigned an identifier and client nodes can use this identifier to specify the clock which they consume. Following indices are allowed: - - 0: 32khz_ap clock, - - 1: 32khz_cp clock, - - 2: 32khz_pmic clock. + - 0: 32khz_ap clock (max77686, max77802), 32khz_out0 (max77620) + - 1: 32khz_cp clock (max77686, max77802), + - 2: 32khz_pmic clock (max77686). + +Clocks are defined as preprocessor macros in above dt-binding header for +respective chips. + +Example: + +1. With MAX77686: + +#include <dt-bindings/clock/maxim,max77686.h> +/* ... */ + + Node of the MFD chip + max77686: max77686@09 { + compatible = "maxim,max77686"; + interrupt-parent = <&wakeup_eint>; + interrupts = <26 0>; + reg = <0x09>; + #clock-cells = <1>; + + /* ... */ + }; + + Clock consumer node + + foo@0 { + compatible = "bar,foo"; + /* ... */ + clock-names = "my-clock"; + clocks = <&max77686 MAX77686_CLK_PMIC>; + }; + +2. With MAX77802: + +#include <dt-bindings/clock/maxim,max77802.h> +/* ... */ + + Node of the MFD chip + max77802: max77802@09 { + compatible = "maxim,max77802"; + interrupt-parent = <&wakeup_eint>; + interrupts = <26 0>; + reg = <0x09>; + #clock-cells = <1>; + + /* ... */ + }; + + Clock consumer node + + foo@0 { + compatible = "bar,foo"; + /* ... */ + clock-names = "my-clock"; + clocks = <&max77802 MAX77802_CLK_32K_AP>; + }; -Clocks are defined as preprocessor macros in dt-bindings/clock/maxim,max77686.h -header and can be used in device tree sources. -Example: Node of the MFD chip +3. With MAX77620: - max77686: max77686@09 { - compatible = "maxim,max77686"; - interrupt-parent = <&wakeup_eint>; - interrupts = <26 0>; - reg = <0x09>; - #clock-cells = <1>; +#include <dt-bindings/clock/maxim,max77620.h> +/* ... */ - /* ... */ - }; + Node of the MFD chip + max77620: max77620@3c { + compatible = "maxim,max77620"; + reg = <0x3c>; + #clock-cells = <1>; + /* ... */ + }; -Example: Clock consumer node + Clock consumer node - foo@0 { - compatible = "bar,foo"; - /* ... */ - clock-names = "my-clock"; - clocks = <&max77686 MAX77686_CLK_PMIC>; - }; + foo@0 { + compatible = "bar,foo"; + /* ... */ + clock-names = "my-clock"; + clocks = <&max77620 MAX77620_CLK_32K_OUT0>; + }; diff --git a/Documentation/devicetree/bindings/clock/maxim,max77802.txt b/Documentation/devicetree/bindings/clock/maxim,max77802.txt deleted file mode 100644 index c6dc7835f06c..000000000000 --- a/Documentation/devicetree/bindings/clock/maxim,max77802.txt +++ /dev/null @@ -1,44 +0,0 @@ -Binding for Maxim MAX77802 32k clock generator block - -This is a part of device tree bindings of MAX77802 multi-function device. -More information can be found in bindings/mfd/max77802.txt file. - -The MAX77802 contains two 32.768khz clock outputs that can be controlled -(gated/ungated) over I2C. - -Following properties should be present in main device node of the MFD chip. - -Required properties: -- #clock-cells: From common clock binding; shall be set to 1. - -Optional properties: -- clock-output-names: From common clock binding. - -Each clock is assigned an identifier and client nodes can use this identifier -to specify the clock which they consume. Following indices are allowed: - - 0: 32khz_ap clock, - - 1: 32khz_cp clock. - -Clocks are defined as preprocessor macros in dt-bindings/clock/maxim,max77802.h -header and can be used in device tree sources. - -Example: Node of the MFD chip - - max77802: max77802@09 { - compatible = "maxim,max77802"; - interrupt-parent = <&wakeup_eint>; - interrupts = <26 0>; - reg = <0x09>; - #clock-cells = <1>; - - /* ... */ - }; - -Example: Clock consumer node - - foo@0 { - compatible = "bar,foo"; - /* ... */ - clock-names = "my-clock"; - clocks = <&max77802 MAX77802_CLK_32K_AP>; - }; diff --git a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt index 660e64912cce..cb8542d910b3 100644 --- a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt +++ b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt @@ -86,6 +86,8 @@ ID Clock Peripheral 7 pex3 PCIe 3 8 pex0 PCIe 0 9 usb3h0 USB3 Host 0 +10 usb3h1 USB3 Host 1 +15 sata0 SATA 0 17 sdio SDIO 22 xor0 XOR 0 28 xor1 XOR 1 diff --git a/Documentation/devicetree/bindings/clock/qcom,gcc.txt b/Documentation/devicetree/bindings/clock/qcom,gcc.txt index 9a60fde32b02..869a2f0e2ff6 100644 --- a/Documentation/devicetree/bindings/clock/qcom,gcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,gcc.txt @@ -15,6 +15,7 @@ Required properties : "qcom,gcc-msm8974pro" "qcom,gcc-msm8974pro-ac" "qcom,gcc-msm8996" + "qcom,gcc-mdm9615" - reg : shall contain base register location and length - #clock-cells : shall contain 1 diff --git a/Documentation/devicetree/bindings/clock/qcom,lcc.txt b/Documentation/devicetree/bindings/clock/qcom,lcc.txt index dd755be63a01..a3c78aa88038 100644 --- a/Documentation/devicetree/bindings/clock/qcom,lcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,lcc.txt @@ -7,6 +7,7 @@ Required properties : "qcom,lcc-msm8960" "qcom,lcc-apq8064" "qcom,lcc-ipq8064" + "qcom,lcc-mdm9615" - reg : shall contain base register location and length - #clock-cells : shall contain 1 diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-divmux.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-divmux.txt deleted file mode 100644 index 6247652044a0..000000000000 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen-divmux.txt +++ /dev/null @@ -1,49 +0,0 @@ -Binding for a ST divider and multiplexer clock driver. - -This binding uses the common clock binding[1]. -Base address is located to the parent node. See clock binding[2] - -[1] Documentation/devicetree/bindings/clock/clock-bindings.txt -[2] Documentation/devicetree/bindings/clock/st/st,clkgen.txt - -Required properties: - -- compatible : shall be: - "st,clkgena-divmux-c65-hs", "st,clkgena-divmux" - "st,clkgena-divmux-c65-ls", "st,clkgena-divmux" - "st,clkgena-divmux-c32-odf0", "st,clkgena-divmux" - "st,clkgena-divmux-c32-odf1", "st,clkgena-divmux" - "st,clkgena-divmux-c32-odf2", "st,clkgena-divmux" - "st,clkgena-divmux-c32-odf3", "st,clkgena-divmux" - -- #clock-cells : From common clock binding; shall be set to 1. - -- clocks : From common clock binding - -- clock-output-names : From common clock binding. - -Example: - - clockgen-a@fd345000 { - reg = <0xfd345000 0xb50>; - - clk_m_a1_div1: clk-m-a1-div1 { - #clock-cells = <1>; - compatible = "st,clkgena-divmux-c32-odf1", - "st,clkgena-divmux"; - - clocks = <&clk_m_a1_osc_prediv>, - <&clk_m_a1_pll0 1>, /* PLL0 PHI1 */ - <&clk_m_a1_pll1 1>; /* PLL1 PHI1 */ - - clock-output-names = "clk-m-rx-icn-ts", - "clk-m-rx-icn-vdp-0", - "", /* unused */ - "clk-m-prv-t1-bus", - "clk-m-icn-reg-12", - "clk-m-icn-reg-10", - "", /* unused */ - "clk-m-icn-st231"; - }; - }; - diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt index f1fa91c68768..9a46cb1d7a04 100644 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt @@ -10,14 +10,7 @@ This binding uses the common clock binding[1]. Required properties: - compatible : shall be: - "st,stih416-clkgenc-vcc-hd", "st,clkgen-mux" - "st,stih416-clkgenf-vcc-fvdp", "st,clkgen-mux" - "st,stih416-clkgenf-vcc-hva", "st,clkgen-mux" - "st,stih416-clkgenf-vcc-hd", "st,clkgen-mux" - "st,stih416-clkgenf-vcc-sd", "st,clkgen-mux" - "st,stih415-clkgen-a9-mux", "st,clkgen-mux" - "st,stih416-clkgen-a9-mux", "st,clkgen-mux" - "st,stih407-clkgen-a9-mux", "st,clkgen-mux" + "st,stih407-clkgen-a9-mux" - #clock-cells : from common clock binding; shall be set to 0. @@ -27,10 +20,13 @@ Required properties: Example: - clk_m_hva: clk-m-hva@fd690868 { + clk_m_a9: clk-m-a9@92b0000 { #clock-cells = <0>; - compatible = "st,stih416-clkgenf-vcc-hva", "st,clkgen-mux"; - reg = <0xfd690868 4>; + compatible = "st,stih407-clkgen-a9-mux"; + reg = <0x92b0000 0x10000>; - clocks = <&clockgen_f 1>, <&clk_m_a1_div0 3>; + clocks = <&clockgen_a9_pll 0>, + <&clockgen_a9_pll 0>, + <&clk_s_c0_flexgen 13>, + <&clk_m_a9_ext2f_div2>; }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt index 844b3a0976bf..f207053e0550 100644 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt @@ -9,24 +9,10 @@ Base address is located to the parent node. See clock binding[2] Required properties: - compatible : shall be: - "st,clkgena-prediv-c65", "st,clkgena-prediv" - "st,clkgena-prediv-c32", "st,clkgena-prediv" - - "st,clkgena-plls-c65" - "st,plls-c32-a1x-0", "st,clkgen-plls-c32" - "st,plls-c32-a1x-1", "st,clkgen-plls-c32" - "st,stih415-plls-c32-a9", "st,clkgen-plls-c32" - "st,stih415-plls-c32-ddr", "st,clkgen-plls-c32" - "st,stih416-plls-c32-a9", "st,clkgen-plls-c32" - "st,stih416-plls-c32-ddr", "st,clkgen-plls-c32" - "st,stih407-plls-c32-a0", "st,clkgen-plls-c32" - "st,stih407-plls-c32-a9", "st,clkgen-plls-c32" - "sst,plls-c32-cx_0", "st,clkgen-plls-c32" - "sst,plls-c32-cx_1", "st,clkgen-plls-c32" - "st,stih418-plls-c28-a9", "st,clkgen-plls-c32" - - "st,stih415-gpu-pll-c32", "st,clkgengpu-pll-c32" - "st,stih416-gpu-pll-c32", "st,clkgengpu-pll-c32" + "st,clkgen-pll0" + "st,clkgen-pll1" + "st,stih407-clkgen-plla9" + "st,stih418-clkgen-plla9" - #clock-cells : From common clock binding; shall be set to 1. @@ -36,17 +22,16 @@ Required properties: Example: - clockgen-a@fee62000 { - reg = <0xfee62000 0xb48>; + clockgen-a9@92b0000 { + compatible = "st,clkgen-c32"; + reg = <0x92b0000 0xffff>; - clk_s_a0_pll: clk-s-a0-pll { + clockgen_a9_pll: clockgen-a9-pll { #clock-cells = <1>; - compatible = "st,clkgena-plls-c65"; + compatible = "st,stih407-clkgen-plla9"; clocks = <&clk_sysin>; - clock-output-names = "clk-s-a0-pll0-hs", - "clk-s-a0-pll0-ls", - "clk-s-a0-pll1"; + clock-output-names = "clockgen-a9-pll-odf"; }; }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-prediv.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-prediv.txt deleted file mode 100644 index 604766c2619e..000000000000 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen-prediv.txt +++ /dev/null @@ -1,36 +0,0 @@ -Binding for a ST pre-divider clock driver. - -This binding uses the common clock binding[1]. -Base address is located to the parent node. See clock binding[2] - -[1] Documentation/devicetree/bindings/clock/clock-bindings.txt -[2] Documentation/devicetree/bindings/clock/st/st,clkgen.txt - -Required properties: - -- compatible : shall be: - "st,clkgena-prediv-c65", "st,clkgena-prediv" - "st,clkgena-prediv-c32", "st,clkgena-prediv" - -- #clock-cells : From common clock binding; shall be set to 0. - -- clocks : From common clock binding - -- clock-output-names : From common clock binding. - -Example: - - clockgen-a@fd345000 { - reg = <0xfd345000 0xb50>; - - clk_m_a2_osc_prediv: clk-m-a2-osc-prediv { - #clock-cells = <0>; - compatible = "st,clkgena-prediv-c32", - "st,clkgena-prediv"; - - clocks = <&clk_sysin>; - - clock-output-names = "clk-m-a2-osc-prediv"; - }; - }; - diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-vcc.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-vcc.txt deleted file mode 100644 index 109b3eddcb17..000000000000 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen-vcc.txt +++ /dev/null @@ -1,61 +0,0 @@ -Binding for a type of STMicroelectronics clock crossbar (VCC). - -The crossbar can take up to 4 input clocks and control up to 16 -output clocks. Not all inputs or outputs have to be in use in a -particular instantiation. Each output can be individually enabled, -select any of the input clocks and apply a divide (by 1,2,4 or 8) to -that selected clock. - -This binding uses the common clock binding[1]. - -[1] Documentation/devicetree/bindings/clock/clock-bindings.txt - -Required properties: - -- compatible : shall be: - "st,stih416-clkgenc", "st,vcc" - "st,stih416-clkgenf", "st,vcc" - -- #clock-cells : from common clock binding; shall be set to 1. - -- reg : A Base address and length of the register set. - -- clocks : from common clock binding - -- clock-output-names : From common clock binding. The block has 16 - clock outputs but not all of them in a specific instance - have to be used in the SoC. If a clock name is left as - an empty string then no clock will be created for the - output associated with that string index. If fewer than - 16 strings are provided then no clocks will be created - for the remaining outputs. - -Example: - - clockgen_c_vcc: clockgen-c-vcc@0xfe8308ac { - #clock-cells = <1>; - compatible = "st,stih416-clkgenc", "st,clkgen-vcc"; - reg = <0xfe8308ac 12>; - - clocks = <&clk_s_vcc_hd>, - <&clockgen_c 1>, - <&clk_s_tmds_fromphy>, - <&clockgen_c 2>; - - clock-output-names = "clk-s-pix-hdmi", - "clk-s-pix-dvo", - "clk-s-out-dvo", - "clk-s-pix-hd", - "clk-s-hddac", - "clk-s-denc", - "clk-s-sddac", - "clk-s-pix-main", - "clk-s-pix-aux", - "clk-s-stfe-frc-0", - "clk-s-ref-mcru", - "clk-s-slave-mcru", - "clk-s-tmds-hdmi", - "clk-s-hdmi-reject-pll", - "clk-s-thsens"; - }; - diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen.txt index b18bf86f926f..c35390f60545 100644 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen.txt +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen.txt @@ -13,14 +13,6 @@ address is common of all subnode. ... }; - prediv_node { - ... - }; - - divmux_node { - ... - }; - quadfs_node { ... }; @@ -29,10 +21,6 @@ address is common of all subnode. ... }; - vcc_node { - ... - }; - flexgen_node { ... }; @@ -43,11 +31,8 @@ This binding uses the common clock binding[1]. Each subnode should use the binding described in [2]..[7] [1] Documentation/devicetree/bindings/clock/clock-bindings.txt -[2] Documentation/devicetree/bindings/clock/st,clkgen-divmux.txt [3] Documentation/devicetree/bindings/clock/st,clkgen-mux.txt [4] Documentation/devicetree/bindings/clock/st,clkgen-pll.txt -[5] Documentation/devicetree/bindings/clock/st,clkgen-prediv.txt -[6] Documentation/devicetree/bindings/clock/st,vcc.txt [7] Documentation/devicetree/bindings/clock/st,quadfs.txt [8] Documentation/devicetree/bindings/clock/st,flexgen.txt @@ -57,44 +42,27 @@ Required properties: Example: - clockgen-a@fee62000 { - - reg = <0xfee62000 0xb48>; + clockgen-a@090ff000 { + compatible = "st,clkgen-c32"; + reg = <0x90ff000 0x1000>; clk_s_a0_pll: clk-s-a0-pll { #clock-cells = <1>; - compatible = "st,clkgena-plls-c65"; - - clocks = <&clk-sysin>; - - clock-output-names = "clk-s-a0-pll0-hs", - "clk-s-a0-pll0-ls", - "clk-s-a0-pll1"; - }; - - clk_s_a0_osc_prediv: clk-s-a0-osc-prediv { - #clock-cells = <0>; - compatible = "st,clkgena-prediv-c65", - "st,clkgena-prediv"; + compatible = "st,clkgen-pll0"; clocks = <&clk_sysin>; - clock-output-names = "clk-s-a0-osc-prediv"; + clock-output-names = "clk-s-a0-pll-ofd-0"; }; - clk_s_a0_hs: clk-s-a0-hs { + clk_s_a0_flexgen: clk-s-a0-flexgen { + compatible = "st,flexgen"; + #clock-cells = <1>; - compatible = "st,clkgena-divmux-c65-hs", - "st,clkgena-divmux"; - clocks = <&clk-s_a0_osc_prediv>, - <&clk-s_a0_pll 0>, /* pll0 hs */ - <&clk-s_a0_pll 2>; /* pll1 */ + clocks = <&clk_s_a0_pll 0>, + <&clk_sysin>; - clock-output-names = "clk-s-fdma-0", - "clk-s-fdma-1", - ""; /* clk-s-jit-sense */ - /* fourth output unused */ + clock-output-names = "clk-ic-lmi0"; }; }; - diff --git a/Documentation/devicetree/bindings/clock/st/st,flexgen.txt b/Documentation/devicetree/bindings/clock/st/st,flexgen.txt index b7ee5c7e0f75..7ff77fc57dff 100644 --- a/Documentation/devicetree/bindings/clock/st/st,flexgen.txt +++ b/Documentation/devicetree/bindings/clock/st/st,flexgen.txt @@ -60,6 +60,10 @@ This binding uses the common clock binding[2]. Required properties: - compatible : shall be: "st,flexgen" + "st,flexgen-audio", "st,flexgen" (enable clock propagation on parent for + audio use case) + "st,flexgen-video", "st,flexgen" (enable clock propagation on parent + and activate synchronous mode) - #clock-cells : from common clock binding; shall be set to 1 (multiple clock outputs). diff --git a/Documentation/devicetree/bindings/clock/st/st,quadfs.txt b/Documentation/devicetree/bindings/clock/st/st,quadfs.txt index cedeb9cc8208..d93d49342e60 100644 --- a/Documentation/devicetree/bindings/clock/st/st,quadfs.txt +++ b/Documentation/devicetree/bindings/clock/st/st,quadfs.txt @@ -11,12 +11,8 @@ This binding uses the common clock binding[1]. Required properties: - compatible : shall be: - "st,stih416-quadfs216", "st,quadfs" - "st,stih416-quadfs432", "st,quadfs" - "st,stih416-quadfs660-E", "st,quadfs" - "st,stih416-quadfs660-F", "st,quadfs" - "st,stih407-quadfs660-C", "st,quadfs" - "st,stih407-quadfs660-D", "st,quadfs" + "st,quadfs" + "st,quadfs-pll" - #clock-cells : from common clock binding; shall be set to 1. @@ -35,14 +31,15 @@ Required properties: Example: - clockgen_e: clockgen-e@fd3208bc { - #clock-cells = <1>; - compatible = "st,stih416-quadfs660-E", "st,quadfs"; - reg = <0xfd3208bc 0xB0>; - - clocks = <&clk_sysin>; - clock-output-names = "clk-m-pix-mdtp-0", - "clk-m-pix-mdtp-1", - "clk-m-pix-mdtp-2", - "clk-m-mpelpc"; - }; + clk_s_c0_quadfs: clk-s-c0-quadfs@9103000 { + #clock-cells = <1>; + compatible = "st,quadfs-pll"; + reg = <0x9103000 0x1000>; + + clocks = <&clk_sysin>; + + clock-output-names = "clk-s-c0-fs0-ch0", + "clk-s-c0-fs0-ch1", + "clk-s-c0-fs0-ch2", + "clk-s-c0-fs0-ch3"; + }; diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt index cb91507ffb1e..3868458a5feb 100644 --- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt +++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt @@ -2,7 +2,10 @@ Allwinner Clock Control Unit Binding ------------------------------------ Required properties : -- compatible: must contain one of the following compatible: +- compatible: must contain one of the following compatibles: + - "allwinner,sun6i-a31-ccu" + - "allwinner,sun8i-a23-ccu" + - "allwinner,sun8i-a33-ccu" - "allwinner,sun8i-h3-ccu" - reg: Must contain the registers base address and length diff --git a/Documentation/devicetree/bindings/clock/uniphier-clock.txt b/Documentation/devicetree/bindings/clock/uniphier-clock.txt new file mode 100644 index 000000000000..c7179d3b5c33 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/uniphier-clock.txt @@ -0,0 +1,134 @@ +UniPhier clock controller + + +System clock +------------ + +Required properties: +- compatible: should be one of the following: + "socionext,uniphier-sld3-clock" - for sLD3 SoC. + "socionext,uniphier-ld4-clock" - for LD4 SoC. + "socionext,uniphier-pro4-clock" - for Pro4 SoC. + "socionext,uniphier-sld8-clock" - for sLD8 SoC. + "socionext,uniphier-pro5-clock" - for Pro5 SoC. + "socionext,uniphier-pxs2-clock" - for PXs2/LD6b SoC. + "socionext,uniphier-ld11-clock" - for LD11 SoC. + "socionext,uniphier-ld20-clock" - for LD20 SoC. +- #clock-cells: should be 1. + +Example: + + sysctrl@61840000 { + compatible = "socionext,uniphier-sysctrl", + "simple-mfd", "syscon"; + reg = <0x61840000 0x4000>; + + clock { + compatible = "socionext,uniphier-ld20-clock"; + #clock-cells = <1>; + }; + + other nodes ... + }; + +Provided clocks: + + 8: ST DMAC +12: GIO (Giga bit stream I/O) +14: USB3 ch0 host +15: USB3 ch1 host +16: USB3 ch0 PHY0 +17: USB3 ch0 PHY1 +20: USB3 ch1 PHY0 +21: USB3 ch1 PHY1 + + +Media I/O (MIO) clock +--------------------- + +Required properties: +- compatible: should be one of the following: + "socionext,uniphier-sld3-mio-clock" - for sLD3 SoC. + "socionext,uniphier-ld4-mio-clock" - for LD4 SoC. + "socionext,uniphier-pro4-mio-clock" - for Pro4 SoC. + "socionext,uniphier-sld8-mio-clock" - for sLD8 SoC. + "socionext,uniphier-pro5-mio-clock" - for Pro5 SoC. + "socionext,uniphier-pxs2-mio-clock" - for PXs2/LD6b SoC. + "socionext,uniphier-ld11-mio-clock" - for LD11 SoC. + "socionext,uniphier-ld20-mio-clock" - for LD20 SoC. +- #clock-cells: should be 1. + +Example: + + mioctrl@59810000 { + compatible = "socionext,uniphier-mioctrl", + "simple-mfd", "syscon"; + reg = <0x59810000 0x800>; + + clock { + compatible = "socionext,uniphier-ld20-mio-clock"; + #clock-cells = <1>; + }; + + other nodes ... + }; + +Provided clocks: + + 0: SD ch0 host + 1: eMMC host + 2: SD ch1 host + 7: MIO DMAC + 8: USB2 ch0 host + 9: USB2 ch1 host +10: USB2 ch2 host +11: USB2 ch3 host +12: USB2 ch0 PHY +13: USB2 ch1 PHY +14: USB2 ch2 PHY +15: USB2 ch3 PHY + + +Peripheral clock +---------------- + +Required properties: +- compatible: should be one of the following: + "socionext,uniphier-sld3-peri-clock" - for sLD3 SoC. + "socionext,uniphier-ld4-peri-clock" - for LD4 SoC. + "socionext,uniphier-pro4-peri-clock" - for Pro4 SoC. + "socionext,uniphier-sld8-peri-clock" - for sLD8 SoC. + "socionext,uniphier-pro5-peri-clock" - for Pro5 SoC. + "socionext,uniphier-pxs2-peri-clock" - for PXs2/LD6b SoC. + "socionext,uniphier-ld11-peri-clock" - for LD11 SoC. + "socionext,uniphier-ld20-peri-clock" - for LD20 SoC. +- #clock-cells: should be 1. + +Example: + + perictrl@59820000 { + compatible = "socionext,uniphier-perictrl", + "simple-mfd", "syscon"; + reg = <0x59820000 0x200>; + + clock { + compatible = "socionext,uniphier-ld20-peri-clock"; + #clock-cells = <1>; + }; + + other nodes ... + }; + +Provided clocks: + + 0: UART ch0 + 1: UART ch1 + 2: UART ch2 + 3: UART ch3 + 4: I2C ch0 + 5: I2C ch1 + 6: I2C ch2 + 7: I2C ch3 + 8: I2C ch4 + 9: I2C ch5 +10: I2C ch6 diff --git a/Documentation/devicetree/bindings/clock/xgene.txt b/Documentation/devicetree/bindings/clock/xgene.txt index 82f9638121db..8233e771711b 100644 --- a/Documentation/devicetree/bindings/clock/xgene.txt +++ b/Documentation/devicetree/bindings/clock/xgene.txt @@ -8,6 +8,7 @@ Required properties: - compatible : shall be one of the following: "apm,xgene-socpll-clock" - for a X-Gene SoC PLL clock "apm,xgene-pcppll-clock" - for a X-Gene PCP PLL clock + "apm,xgene-pmd-clock" - for a X-Gene PMD clock "apm,xgene-device-clock" - for a X-Gene device clock "apm,xgene-socpll-v2-clock" - for a X-Gene SoC PLL v2 clock "apm,xgene-pcppll-v2-clock" - for a X-Gene PCP PLL v2 clock @@ -22,6 +23,15 @@ Required properties for SoC or PCP PLL clocks: Optional properties for PLL clocks: - clock-names : shall be the name of the PLL. If missing, use the device name. +Required properties for PMD clocks: +- reg : shall be the physical register address for the pmd clock. +- clocks : shall be the input parent clock phandle for the clock. +- #clock-cells : shall be set to 1. +- clock-output-names : shall be the name of the clock referenced by derive + clock. +Optional properties for PLL clocks: +- clock-names : shall be the name of the clock. If missing, use the device name. + Required properties for device clocks: - reg : shall be a list of address and length pairs describing the CSR reset and/or the divider. Either may be omitted, but at least @@ -59,6 +69,14 @@ For example: type = <0>; }; + pmd0clk: pmd0clk@7e200200 { + compatible = "apm,xgene-pmd-clock"; + #clock-cells = <1>; + clocks = <&pmdpll 0>; + reg = <0x0 0x7e200200 0x0 0x10>; + clock-output-names = "pmd0clk"; + }; + socpll: socpll@17000120 { compatible = "apm,xgene-socpll-clock"; #clock-cells = <1>; diff --git a/Documentation/devicetree/bindings/clock/zx296718-clk.txt b/Documentation/devicetree/bindings/clock/zx296718-clk.txt new file mode 100644 index 000000000000..8c18b7b237bf --- /dev/null +++ b/Documentation/devicetree/bindings/clock/zx296718-clk.txt @@ -0,0 +1,35 @@ +Device Tree Clock bindings for ZTE zx296718 + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be one of the following: + "zte,zx296718-topcrm": + zx296718 top clock selection, divider and gating + + "zte,zx296718-lsp0crm" and + "zte,zx296718-lsp1crm": + zx296718 device level clock selection and gating + +- reg: Address and length of the register set + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/zx296718-clock.h +for the full list of zx296718 clock IDs. + + +topclk: topcrm@1461000 { + compatible = "zte,zx296718-topcrm-clk"; + reg = <0x01461000 0x1000>; + #clock-cells = <1>; +}; + +usbphy0:usb-phy0 { + compatible = "zte,zx296718-usb-phy"; + #phy-cells = <0>; + clocks = <&topclk USB20_PHY_CLK>; + clock-names = "phyclk"; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/devfreq/event/rockchip-dfi.txt b/Documentation/devicetree/bindings/devfreq/event/rockchip-dfi.txt new file mode 100644 index 000000000000..f2233138eba9 --- /dev/null +++ b/Documentation/devicetree/bindings/devfreq/event/rockchip-dfi.txt @@ -0,0 +1,19 @@ + +* Rockchip rk3399 DFI device + +Required properties: +- compatible: Must be "rockchip,rk3399-dfi". +- reg: physical base address of each DFI and length of memory mapped region +- rockchip,pmu: phandle to the syscon managing the "pmu general register files" +- clocks: phandles for clock specified in "clock-names" property +- clock-names : the name of clock used by the DFI, must be "pclk_ddr_mon"; + +Example: + dfi: dfi@0xff630000 { + compatible = "rockchip,rk3399-dfi"; + reg = <0x00 0xff630000 0x00 0x4000>; + rockchip,pmu = <&pmugrf>; + clocks = <&cru PCLK_DDR_MON>; + clock-names = "pclk_ddr_mon"; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt new file mode 100644 index 000000000000..7a9e8603c150 --- /dev/null +++ b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt @@ -0,0 +1,209 @@ +* Rockchip rk3399 DMC(Dynamic Memory Controller) device + +Required properties: +- compatible: Must be "rockchip,rk3399-dmc". +- devfreq-events: Node to get DDR loading, Refer to + Documentation/devicetree/bindings/devfreq/ + rockchip-dfi.txt +- interrupts: The interrupt number to the CPU. The interrupt + specifier format depends on the interrupt controller. + It should be DCF interrupts, when DDR dvfs finish, + it will happen. +- clocks: Phandles for clock specified in "clock-names" property +- clock-names : The name of clock used by the DFI, must be + "pclk_ddr_mon"; +- operating-points-v2: Refer to Documentation/devicetree/bindings/power/opp.txt + for details. +- center-supply: DMC supply node. +- status: Marks the node enabled/disabled. + +Following properties are ddr timing: + +- rockchip,dram_speed_bin : Value reference include/dt-bindings/clock/ddr.h, + it select ddr3 cl-trp-trcd type, default value + "DDR3_DEFAULT".it must selected according to + "Speed Bin" in ddr3 datasheet, DO NOT use + smaller "Speed Bin" than ddr3 exactly is. + +- rockchip,pd_idle : Config the PD_IDLE value, defined the power-down + idle period, memories are places into power-down + mode if bus is idle for PD_IDLE DFI clocks. + +- rockchip,sr_idle : Configure the SR_IDLE value, defined the + selfrefresh idle period, memories are places + into self-refresh mode if bus is idle for + SR_IDLE*1024 DFI clocks (DFI clocks freq is + half of dram's clocks), defaule value is "0". + +- rockchip,sr_mc_gate_idle : Defined the self-refresh with memory and + controller clock gating idle period, memories + are places into self-refresh mode and memory + controller clock arg gating if bus is idle for + sr_mc_gate_idle*1024 DFI clocks. + +- rockchip,srpd_lite_idle : Defined the self-refresh power down idle + period, memories are places into self-refresh + power down mode if bus is idle for + srpd_lite_idle*1024 DFI clocks. This parameter + is for LPDDR4 only. + +- rockchip,standby_idle : Defined the standby idle period, memories are + places into self-refresh than controller, pi, + phy and dram clock will gating if bus is idle + for standby_idle * DFI clocks. + +- rockchip,dram_dll_disb_freq : It's defined the DDR3 dll bypass frequency in + MHz, when ddr freq less than DRAM_DLL_DISB_FREQ, + ddr3 dll will bypssed note: if dll was bypassed, + the odt also stop working. + +- rockchip,phy_dll_disb_freq : Defined the PHY dll bypass frequency in + MHz (Mega Hz), when ddr freq less than + DRAM_DLL_DISB_FREQ, phy dll will bypssed. + note: phy dll and phy odt are independent. + +- rockchip,ddr3_odt_disb_freq : When dram type is DDR3, this parameter defined + the odt disable frequency in MHz (Mega Hz), + when ddr frequency less then ddr3_odt_disb_freq, + the odt on dram side and controller side are + both disabled. + +- rockchip,ddr3_drv : When dram type is DDR3, this parameter define + the dram side driver stength in ohm, default + value is DDR3_DS_40ohm. + +- rockchip,ddr3_odt : When dram type is DDR3, this parameter define + the dram side ODT stength in ohm, default value + is DDR3_ODT_120ohm. + +- rockchip,phy_ddr3_ca_drv : When dram type is DDR3, this parameter define + the phy side CA line(incluing command line, + address line and clock line) driver strength. + Default value is PHY_DRV_ODT_40. + +- rockchip,phy_ddr3_dq_drv : When dram type is DDR3, this parameter define + the phy side DQ line(incluing DQS/DQ/DM line) + driver strength. default value is PHY_DRV_ODT_40. + +- rockchip,phy_ddr3_odt : When dram type is DDR3, this parameter define the + phy side odt strength, default value is + PHY_DRV_ODT_240. + +- rockchip,lpddr3_odt_disb_freq : When dram type is LPDDR3, this parameter defined + then odt disable frequency in MHz (Mega Hz), + when ddr frequency less then ddr3_odt_disb_freq, + the odt on dram side and controller side are + both disabled. + +- rockchip,lpddr3_drv : When dram type is LPDDR3, this parameter define + the dram side driver stength in ohm, default + value is LP3_DS_34ohm. + +- rockchip,lpddr3_odt : When dram type is LPDDR3, this parameter define + the dram side ODT stength in ohm, default value + is LP3_ODT_240ohm. + +- rockchip,phy_lpddr3_ca_drv : When dram type is LPDDR3, this parameter define + the phy side CA line(incluing command line, + address line and clock line) driver strength. + default value is PHY_DRV_ODT_40. + +- rockchip,phy_lpddr3_dq_drv : When dram type is LPDDR3, this parameter define + the phy side DQ line(incluing DQS/DQ/DM line) + driver strength. default value is + PHY_DRV_ODT_40. + +- rockchip,phy_lpddr3_odt : When dram type is LPDDR3, this parameter define + the phy side odt strength, default value is + PHY_DRV_ODT_240. + +- rockchip,lpddr4_odt_disb_freq : When dram type is LPDDR4, this parameter + defined the odt disable frequency in + MHz (Mega Hz), when ddr frequency less then + ddr3_odt_disb_freq, the odt on dram side and + controller side are both disabled. + +- rockchip,lpddr4_drv : When dram type is LPDDR4, this parameter define + the dram side driver stength in ohm, default + value is LP4_PDDS_60ohm. + +- rockchip,lpddr4_dq_odt : When dram type is LPDDR4, this parameter define + the dram side ODT on dqs/dq line stength in ohm, + default value is LP4_DQ_ODT_40ohm. + +- rockchip,lpddr4_ca_odt : When dram type is LPDDR4, this parameter define + the dram side ODT on ca line stength in ohm, + default value is LP4_CA_ODT_40ohm. + +- rockchip,phy_lpddr4_ca_drv : When dram type is LPDDR4, this parameter define + the phy side CA line(incluing command address + line) driver strength. default value is + PHY_DRV_ODT_40. + +- rockchip,phy_lpddr4_ck_cs_drv : When dram type is LPDDR4, this parameter define + the phy side clock line and cs line driver + strength. default value is PHY_DRV_ODT_80. + +- rockchip,phy_lpddr4_dq_drv : When dram type is LPDDR4, this parameter define + the phy side DQ line(incluing DQS/DQ/DM line) + driver strength. default value is PHY_DRV_ODT_80. + +- rockchip,phy_lpddr4_odt : When dram type is LPDDR4, this parameter define + the phy side odt strength, default value is + PHY_DRV_ODT_60. + +Example: + dmc_opp_table: dmc_opp_table { + compatible = "operating-points-v2"; + + opp00 { + opp-hz = /bits/ 64 <300000000>; + opp-microvolt = <900000>; + }; + opp01 { + opp-hz = /bits/ 64 <666000000>; + opp-microvolt = <900000>; + }; + }; + + dmc: dmc { + compatible = "rockchip,rk3399-dmc"; + devfreq-events = <&dfi>; + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_DDRCLK>; + clock-names = "dmc_clk"; + operating-points-v2 = <&dmc_opp_table>; + center-supply = <&ppvar_centerlogic>; + upthreshold = <15>; + downdifferential = <10>; + rockchip,ddr3_speed_bin = <21>; + rockchip,pd_idle = <0x40>; + rockchip,sr_idle = <0x2>; + rockchip,sr_mc_gate_idle = <0x3>; + rockchip,srpd_lite_idle = <0x4>; + rockchip,standby_idle = <0x2000>; + rockchip,dram_dll_dis_freq = <300>; + rockchip,phy_dll_dis_freq = <125>; + rockchip,auto_pd_dis_freq = <666>; + rockchip,ddr3_odt_dis_freq = <333>; + rockchip,ddr3_drv = <DDR3_DS_40ohm>; + rockchip,ddr3_odt = <DDR3_ODT_120ohm>; + rockchip,phy_ddr3_ca_drv = <PHY_DRV_ODT_40>; + rockchip,phy_ddr3_dq_drv = <PHY_DRV_ODT_40>; + rockchip,phy_ddr3_odt = <PHY_DRV_ODT_240>; + rockchip,lpddr3_odt_dis_freq = <333>; + rockchip,lpddr3_drv = <LP3_DS_34ohm>; + rockchip,lpddr3_odt = <LP3_ODT_240ohm>; + rockchip,phy_lpddr3_ca_drv = <PHY_DRV_ODT_40>; + rockchip,phy_lpddr3_dq_drv = <PHY_DRV_ODT_40>; + rockchip,phy_lpddr3_odt = <PHY_DRV_ODT_240>; + rockchip,lpddr4_odt_dis_freq = <333>; + rockchip,lpddr4_drv = <LP4_PDDS_60ohm>; + rockchip,lpddr4_dq_odt = <LP4_DQ_ODT_40ohm>; + rockchip,lpddr4_ca_odt = <LP4_CA_ODT_40ohm>; + rockchip,phy_lpddr4_ca_drv = <PHY_DRV_ODT_40>; + rockchip,phy_lpddr4_ck_cs_drv = <PHY_DRV_ODT_80>; + rockchip,phy_lpddr4_dq_drv = <PHY_DRV_ODT_80>; + rockchip,phy_lpddr4_odt = <PHY_DRV_ODT_60>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt new file mode 100644 index 000000000000..35383adb10f1 --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt @@ -0,0 +1,41 @@ +Qualcomm's PM8941 USB ID Extcon device + +Some Qualcomm PMICs have a "misc" module that can be used to detect when +the USB ID pin has been pulled low or high. + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: Should contain "qcom,pm8941-misc"; + +- reg: + Usage: required + Value type: <u32> + Definition: Should contain the offset to the misc address space + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: Should contain the usb id interrupt + +- interrupt-names: + Usage: required + Value type: <stringlist> + Definition: Should contain the string "usb_id" for the usb id interrupt + +Example: + + pmic { + usb_id: misc@900 { + compatible = "qcom,pm8941-misc"; + reg = <0x900>; + interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>; + interrupt-names = "usb_id"; + }; + } + + usb-controller { + extcon = <&usb_id>; + }; diff --git a/Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.txt b/Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.txt new file mode 100644 index 000000000000..e7853143fa42 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.txt @@ -0,0 +1,46 @@ +Bindings for the Broadcom's brcm,bcm6345-gpio memory-mapped GPIO controllers. + +These bindings can be used on any BCM63xx SoC. However, BCM6338 and BCM6345 +are the only ones which don't need a pinctrl driver. +BCM6338 have 8-bit data and dirout registers, where GPIO state can be read +and/or written, and the direction changed from input to output. +BCM6345 have 16-bit data and dirout registers, where GPIO state can be read +and/or written, and the direction changed from input to output. + +Required properties: + - compatible: should be "brcm,bcm6345-gpio" + - reg-names: must contain + "dat" - data register + "dirout" - direction (output) register + - reg: address + size pairs describing the GPIO register sets; + order must correspond with the order of entries in reg-names + - #gpio-cells: must be set to 2. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low + - gpio-controller: Marks the device node as a gpio controller. + +Optional properties: + - native-endian: use native endian memory. + +Examples: + - BCM6338: + gpio: gpio-controller@fffe0407 { + compatible = "brcm,bcm6345-gpio"; + reg-names = "dirout", "dat"; + reg = <0xfffe0407 1>, <0xfffe040f 1>; + + #gpio-cells = <2>; + gpio-controller; + }; + + - BCM6345: + gpio: gpio-controller@fffe0406 { + compatible = "brcm,bcm6345-gpio"; + reg-names = "dirout", "dat"; + reg = <0xfffe0406 2>, <0xfffe040a 2>; + native-endian; + + #gpio-cells = <2>; + gpio-controller; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-aspeed.txt b/Documentation/devicetree/bindings/gpio/gpio-aspeed.txt new file mode 100644 index 000000000000..393bb2ed8a77 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-aspeed.txt @@ -0,0 +1,36 @@ +Aspeed GPIO controller Device Tree Bindings +------------------------------------------- + +Required properties: +- compatible : Either "aspeed,ast2400-gpio" or "aspeed,ast2500-gpio" + +- #gpio-cells : Should be two + - First cell is the GPIO line number + - Second cell is used to specify optional + parameters (unused) + +- reg : Address and length of the register set for the device +- gpio-controller : Marks the device node as a GPIO controller. +- interrupts : Interrupt specifier (see interrupt bindings for + details) +- interrupt-controller : Mark the GPIO controller as an interrupt-controller + +Optional properties: + +- interrupt-parent : The parent interrupt controller, optional if inherited + +The gpio and interrupt properties are further described in their respective +bindings documentation: + +- Documentation/devicetree/bindings/gpio/gpio.txt +- Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + + Example: + gpio@1e780000 { + #gpio-cells = <2>; + compatible = "aspeed,ast2400-gpio"; + gpio-controller; + interrupts = <20>; + reg = <0x1e780000 0x1000>; + interrupt-controller; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-axp209.txt b/Documentation/devicetree/bindings/gpio/gpio-axp209.txt new file mode 100644 index 000000000000..a6611304dd3c --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-axp209.txt @@ -0,0 +1,30 @@ +AXP209 GPIO controller + +This driver follows the usual GPIO bindings found in +Documentation/devicetree/bindings/gpio/gpio.txt + +Required properties: +- compatible: Should be "x-powers,axp209-gpio" +- #gpio-cells: Should be two. The first cell is the pin number and the + second is the GPIO flags. +- gpio-controller: Marks the device node as a GPIO controller. + +This node must be a subnode of the axp20x PMIC, documented in +Documentation/devicetree/bindings/mfd/axp20x.txt + +Example: + +axp209: pmic@34 { + compatible = "x-powers,axp209"; + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + + axp_gpio: gpio { + compatible = "x-powers,axp209-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-tpic2810.txt b/Documentation/devicetree/bindings/gpio/gpio-tpic2810.txt new file mode 100644 index 000000000000..1afc2de7a537 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-tpic2810.txt @@ -0,0 +1,16 @@ +TPIC2810 GPIO controller bindings + +Required properties: + - compatible : Should be "ti,tpic2810". + - reg : The I2C address of the device + - gpio-controller : Marks the device node as a GPIO controller. + - #gpio-cells : Should be two. For consumer use see gpio.txt. + +Example: + + gpio@60 { + compatible = "ti,tpic2810"; + reg = <0x60>; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-tps65086.txt b/Documentation/devicetree/bindings/gpio/gpio-tps65086.txt deleted file mode 100644 index ba051074bedc..000000000000 --- a/Documentation/devicetree/bindings/gpio/gpio-tps65086.txt +++ /dev/null @@ -1,16 +0,0 @@ -* TPS65086 GPO Controller bindings - -Required properties: - - compatible : Should be "ti,tps65086-gpio". - - gpio-controller : Marks the device node as a GPIO Controller. - - #gpio-cells : Should be two. The first cell is the pin number - and the second cell is used to specify flags. - See ../gpio/gpio.txt for possible values. - -Example: - - gpio4: gpio { - compatible = "ti,tps65086-gpio"; - gpio-controller; - #gpio-cells = <2>; - }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-ts4900.txt b/Documentation/devicetree/bindings/gpio/gpio-ts4900.txt new file mode 100644 index 000000000000..3f8e71b1ab2a --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-ts4900.txt @@ -0,0 +1,30 @@ +* Technologic Systems I2C-FPGA's GPIO controller bindings + +This bindings describes the GPIO controller for Technologic's FPGA core. +TS-4900's FPGA encodes the GPIO state on 3 bits, whereas the TS-7970's FPGA +uses 2 bits: it doesn't use a dedicated input bit. + +Required properties: +- compatible: Should be one of the following + "technologic,ts4900-gpio" + "technologic,ts7970-gpio" +- reg: Physical base address of the controller and length + of memory mapped region. +- #gpio-cells: Should be two. The first cell is the pin number. +- gpio-controller: Marks the device node as a gpio controller. + +Optional property: +- ngpios: Number of GPIOs this controller is instantiated with, + the default is 32. See gpio.txt for more details. + +Example: + +&i2c2 { + gpio8: gpio@28 { + compatible = "technologic,ts4900-gpio"; + reg = <0x28>; + #gpio-cells = <2>; + gpio-controller; + ngpios = <32>; + }; +}; diff --git a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt index 98d198396956..c3d016532d8e 100644 --- a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt @@ -44,26 +44,3 @@ Example for a PXA3xx platform: interrupt-controller; #interrupt-cells = <0x2>; }; - -* Marvell Orion GPIO Controller - -Required properties: -- compatible : Should be "marvell,orion-gpio" -- reg : Address and length of the register set for controller. -- gpio-controller : So we know this is a gpio controller. -- ngpio : How many gpios this controller has. -- interrupts : Up to 4 Interrupts for the controller. - -Optional properties: -- mask-offset : For SMP Orions, offset for Nth CPU - -Example: - - gpio0: gpio@10100 { - compatible = "marvell,orion-gpio"; - #gpio-cells = <2>; - gpio-controller; - reg = <0x10100 0x40>; - ngpio = <32>; - interrupts = <35>, <36>, <37>, <38>; - }; diff --git a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt index 8da26b35b5c3..7c1ab3b3254f 100644 --- a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt +++ b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -11,6 +11,7 @@ Required Properties: - "renesas,gpio-r8a7793": for R8A7793 (R-Car M2-N) compatible GPIO controller. - "renesas,gpio-r8a7794": for R8A7794 (R-Car E2) compatible GPIO controller. - "renesas,gpio-r8a7795": for R8A7795 (R-Car H3) compatible GPIO controller. + - "renesas,gpio-r8a7796": for R8A7796 (R-Car M3-W) compatible GPIO controller. - "renesas,gpio-rcar": for generic R-Car GPIO controller. - reg: Base address and length of each memory resource used by the GPIO diff --git a/Documentation/devicetree/bindings/hwmon/ltc4151.txt b/Documentation/devicetree/bindings/hwmon/ltc4151.txt new file mode 100644 index 000000000000..d008a5ef525a --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/ltc4151.txt @@ -0,0 +1,18 @@ +LTC4151 High Voltage I2C Current and Voltage Monitor + +Required properties: +- compatible: Must be "lltc,ltc4151" +- reg: I2C address + +Optional properties: +- shunt-resistor-micro-ohms + Shunt resistor value in micro-Ohms + Defaults to <1000> if unset. + +Example: + +ltc4151@6e { + compatible = "lltc,ltc4151"; + reg = <0x6e>; + shunt-resistor-micro-ohms = <1500>; +}; diff --git a/Documentation/devicetree/bindings/hwmon/max6650.txt b/Documentation/devicetree/bindings/hwmon/max6650.txt new file mode 100644 index 000000000000..f6bd87d8e284 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/max6650.txt @@ -0,0 +1,28 @@ +Bindings for MAX6651 and MAX6650 I2C fan controllers + +Reference: +[1] https://datasheets.maximintegrated.com/en/ds/MAX6650-MAX6651.pdf + +Required properties: +- compatible : One of "maxim,max6650" or "maxim,max6651" +- reg : I2C address, one of 0x1b, 0x1f, 0x4b, 0x48. + +Optional properties, default is to retain the chip's current setting: +- maxim,fan-microvolt : The supply voltage of the fan, either 5000000 uV or + 12000000 uV. +- maxim,fan-prescale : Pre-scaling value, as per datasheet [1]. Lower values + allow more fine-grained control of slower fans. + Valid: 1, 2, 4, 8, 16. +- maxim,fan-target-rpm: Initial requested fan rotation speed. If specified, the + driver selects closed-loop mode and the requested speed. + This ensures the fan is already running before userspace + takes over. + +Example: + fan-max6650: max6650@1b { + reg = <0x1b>; + compatible = "maxim,max6650"; + maxim,fan-microvolt = <12000000>; + maxim,fan-prescale = <4>; + maxim,fan-target-rpm = <1200>; + }; diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index 5c70ce9c1954..1416c6a0d2cd 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -38,6 +38,7 @@ dallas,ds4510 CPU Supervisor with Nonvolatile Memory and Programmable I/O dallas,ds75 Digital Thermometer and Thermostat dlg,da9053 DA9053: flexible system level PMIC with multicore support dlg,da9063 DA9063: system PMIC for quad-core application processors +domintech,dmard09 DMARD09: 3-axis Accelerometer epson,rx8010 I2C-BUS INTERFACE REAL TIME CLOCK MODULE epson,rx8025 High-Stability. I2C-Bus INTERFACE REAL TIME CLOCK MODULE epson,rx8581 I2C-BUS INTERFACE REAL TIME CLOCK MODULE @@ -56,6 +57,7 @@ maxim,ds1050 5 Bit Programmable, Pulse-Width Modulator maxim,max1237 Low-Power, 4-/12-Channel, 2-Wire Serial, 12-Bit ADCs maxim,max6625 9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface mc,rv3029c2 Real Time Clock Module with I2C-Bus +mcube,mc3230 mCube 3-axis 8-bit digital accelerometer microchip,mcp4531-502 Microchip 7-bit Single I2C Digital Potentiometer (5k) microchip,mcp4531-103 Microchip 7-bit Single I2C Digital Potentiometer (10k) microchip,mcp4531-503 Microchip 7-bit Single I2C Digital Potentiometer (50k) diff --git a/Documentation/devicetree/bindings/iio/accel/dmard06.txt b/Documentation/devicetree/bindings/iio/accel/dmard06.txt new file mode 100644 index 000000000000..ce105a12c645 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/dmard06.txt @@ -0,0 +1,19 @@ +Device tree bindings for Domintech DMARD05, DMARD06, DMARD07 accelerometers + +Required properties: + - compatible : Should be "domintech,dmard05" + or "domintech,dmard06" + or "domintech,dmard07" + - reg : I2C address of the chip. Should be 0x1c + +Example: + &i2c1 { + /* ... */ + + accelerometer@1c { + compatible = "domintech,dmard06"; + reg = <0x1c>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/iio/accel/kionix,kxsd9.txt b/Documentation/devicetree/bindings/iio/accel/kionix,kxsd9.txt new file mode 100644 index 000000000000..b25bf3a77e0f --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/kionix,kxsd9.txt @@ -0,0 +1,22 @@ +Kionix KXSD9 Accelerometer device tree bindings + +Required properties: + - compatible: should be set to "kionix,kxsd9" + - reg: i2c slave address + +Optional properties: + - vdd-supply: The input supply for VDD + - iovdd-supply: The input supply for IOVDD + - interrupts: The movement detection interrupt + - mount-matrix: See mount-matrix.txt + +Example: + +kxsd9@18 { + compatible = "kionix,kxsd9"; + reg = <0x18>; + interrupt-parent = <&foo>; + interrupts = <57 IRQ_TYPE_EDGE_FALLING>; + iovdd-supply = <&bar>; + vdd-supply = <&baz>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt b/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt new file mode 100644 index 000000000000..68c45cbbe3d9 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt @@ -0,0 +1,29 @@ +* Mediatek AUXADC - Analog to Digital Converter on Mediatek mobile soc (mt65xx/mt81xx/mt27xx) +=============== + +The Auxiliary Analog/Digital Converter (AUXADC) is an ADC found +in some Mediatek SoCs which among other things measures the temperatures +in the SoC. It can be used directly with register accesses, but it is also +used by thermal controller which reads the temperatures from the AUXADC +directly via its own bus interface. See +Documentation/devicetree/bindings/thermal/mediatek-thermal.txt +for the Thermal Controller which holds a phandle to the AUXADC. + +Required properties: + - compatible: Should be one of: + - "mediatek,mt2701-auxadc": For MT2701 family of SoCs + - "mediatek,mt8173-auxadc": For MT8173 family of SoCs + - reg: Address range of the AUXADC unit. + - clocks: Should contain a clock specifier for each entry in clock-names + - clock-names: Should contain "main". + - #io-channel-cells: Should be 1, see ../iio-bindings.txt + +Example: + +auxadc: adc@11001000 { + compatible = "mediatek,mt2701-auxadc"; + reg = <0 0x11001000 0 0x1000>; + clocks = <&pericfg CLK_PERI_AUXADC>; + clock-names = "main"; + #io-channel-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt b/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt index bf99e2f24788..205593f56fe7 100644 --- a/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt +++ b/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt @@ -16,6 +16,11 @@ Required properties: - vref-supply: The regulator supply ADC reference voltage. - #io-channel-cells: Should be 1, see ../iio-bindings.txt +Optional properties: +- resets: Must contain an entry for each entry in reset-names if need support + this option. See ../reset/reset.txt for details. +- reset-names: Must include the name "saradc-apb". + Example: saradc: saradc@2006c000 { compatible = "rockchip,saradc"; @@ -23,6 +28,8 @@ Example: interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>; clock-names = "saradc", "apb_pclk"; + resets = <&cru SRST_SARADC>; + reset-names = "saradc-apb"; #io-channel-cells = <1>; vref-supply = <&vcc18>; }; diff --git a/Documentation/devicetree/bindings/iio/adc/ti-adc12138.txt b/Documentation/devicetree/bindings/iio/adc/ti-adc12138.txt new file mode 100644 index 000000000000..049a1d36f013 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti-adc12138.txt @@ -0,0 +1,37 @@ +* Texas Instruments' ADC12130/ADC12132/ADC12138 + +Required properties: + - compatible: Should be one of + * "ti,adc12130" + * "ti,adc12132" + * "ti,adc12138" + - reg: SPI chip select number for the device + - interrupts: Should contain interrupt for EOC (end of conversion) + - clocks: phandle to conversion clock input + - spi-max-frequency: Definision as per + Documentation/devicetree/bindings/spi/spi-bus.txt + - vref-p-supply: The regulator supply for positive analog voltage reference + +Optional properties: + - vref-n-supply: The regulator supply for negative analog voltage reference + (Note that this must not go below GND or exceed vref-p) + If not specified, this is assumed to be analog ground. + - ti,acquisition-time: The number of conversion clock periods for the S/H's + acquisition time. Should be one of 6, 10, 18, 34. If not specified, + default value of 10 is used. + For high source impedances, this value can be increased to 18 or 34. + For less ADC accuracy and/or slower CCLK frequencies this value may be + decreased to 6. See section 6.0 INPUT SOURCE RESISTANCE in the + datasheet for details. + +Example: +adc@0 { + compatible = "ti,adc12138"; + reg = <0>; + interrupts = <28 IRQ_TYPE_EDGE_RISING>; + interrupt-parent = <&gpio1>; + clocks = <&cclk>; + vref-p-supply = <&ldo4_reg>; + spi-max-frequency = <5000000>; + ti,acquisition-time = <6>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/ti-adc161s626.txt b/Documentation/devicetree/bindings/iio/adc/ti-adc161s626.txt new file mode 100644 index 000000000000..9ed2315781e4 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti-adc161s626.txt @@ -0,0 +1,16 @@ +* Texas Instruments ADC141S626 and ADC161S626 chips + +Required properties: + - compatible: Should be "ti,adc141s626" or "ti,adc161s626" + - reg: spi chip select number for the device + +Recommended properties: + - spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: +adc@0 { + compatible = "ti,adc161s626"; + reg = <0>; + spi-max-frequency = <4300000>; +}; diff --git a/Documentation/devicetree/bindings/iio/chemical/atlas,orp-sm.txt b/Documentation/devicetree/bindings/iio/chemical/atlas,orp-sm.txt new file mode 100644 index 000000000000..5d8b687d5edc --- /dev/null +++ b/Documentation/devicetree/bindings/iio/chemical/atlas,orp-sm.txt @@ -0,0 +1,22 @@ +* Atlas Scientific ORP-SM OEM sensor + +https://www.atlas-scientific.com/_files/_datasheets/_oem/ORP_oem_datasheet.pdf + +Required properties: + + - compatible: must be "atlas,orp-sm" + - reg: the I2C address of the sensor + - interrupt-parent: should be the phandle for the interrupt controller + - interrupts: the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic interrupt client + node bindings. + +Example: + +atlas@66 { + compatible = "atlas,orp-sm"; + reg = <0x66>; + interrupt-parent = <&gpio1>; + interrupts = <16 2>; +}; diff --git a/Documentation/devicetree/bindings/iio/magnetometer/ak8974.txt b/Documentation/devicetree/bindings/iio/magnetometer/ak8974.txt new file mode 100644 index 000000000000..77d5aba1bd8c --- /dev/null +++ b/Documentation/devicetree/bindings/iio/magnetometer/ak8974.txt @@ -0,0 +1,29 @@ +* Asahi Kasei AK8974 magnetometer sensor + +Required properties: + +- compatible : should be "asahi-kasei,ak8974" +- reg : the I2C address of the magnetometer + +Optional properties: + +- avdd-supply: regulator supply for the analog voltage + (see regulator/regulator.txt) +- dvdd-supply: regulator supply for the digital voltage + (see regulator/regulator.txt) +- interrupts: data ready (DRDY) and interrupt (INT1) lines + from the chip, the DRDY interrupt must be placed first. + The interrupts can be triggered on rising or falling + edges alike. +- mount-matrix: an optional 3x3 mounting rotation matrix + +Example: + +ak8974@0f { + compatible = "asahi-kasei,ak8974"; + reg = <0x0f>; + avdd-supply = <&foo_reg>; + dvdd-supply = <&bar_reg>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>, + <1 IRQ_TYPE_EDGE_RISING>; +}; diff --git a/Documentation/devicetree/bindings/iio/pressure/zpa2326.txt b/Documentation/devicetree/bindings/iio/pressure/zpa2326.txt new file mode 100644 index 000000000000..fb85de676e03 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/pressure/zpa2326.txt @@ -0,0 +1,31 @@ +Murata ZPA2326 pressure sensor + +Pressure sensor from Murata with SPI and I2C bus interfaces. + +Required properties: +- compatible: "murata,zpa2326" +- reg: the I2C address or SPI chip select the device will respond to + +Recommended properties for SPI bus usage: +- spi-max-frequency: maximum SPI bus frequency as documented in + Documentation/devicetree/bindings/spi/spi-bus.txt + +Optional properties: +- vref-supply: an optional regulator that needs to be on to provide VREF + power to the sensor +- vdd-supply: an optional regulator that needs to be on to provide VDD + power to the sensor +- interrupt-parent: phandle to the parent interrupt controller as documented in + Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +- interrupts: interrupt mapping for IRQ as documented in + Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + +Example: + +zpa2326@5c { + compatible = "murata,zpa2326"; + reg = <0x5c>; + interrupt-parent = <&gpio>; + interrupts = <12>; + vdd-supply = <&ldo_1v8_gnss>; +}; diff --git a/Documentation/devicetree/bindings/iio/proximity/sx9500.txt b/Documentation/devicetree/bindings/iio/proximity/sx9500.txt new file mode 100644 index 000000000000..b301dd2b35da --- /dev/null +++ b/Documentation/devicetree/bindings/iio/proximity/sx9500.txt @@ -0,0 +1,24 @@ +Semtech's SX9500 capacitive proximity button device driver + +Required properties: + - compatible: must be "semtech,sx9500" + - reg: i2c address where to find the device + - interrupt-parent : should be the phandle for the interrupt controller + - interrupts : the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic + interrupt client node bindings. + +Optional properties: + - reset-gpios: Reference to the GPIO connected to the device's active + low reset pin. + +Example: + +sx9500@28 { + compatible = "semtech,sx9500"; + reg = <0x28>; + interrupt-parent = <&gpio2>; + interrupts = <16 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>; +}; diff --git a/Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt b/Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt new file mode 100644 index 000000000000..28bc5c4d965b --- /dev/null +++ b/Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt @@ -0,0 +1,21 @@ +Maxim thermocouple support + +* https://datasheets.maximintegrated.com/en/ds/MAX6675.pdf +* https://datasheets.maximintegrated.com/en/ds/MAX31855.pdf + +Required properties: + + - compatible: must be "maxim,max31855" or "maxim,max6675" + - reg: SPI chip select number for the device + - spi-max-frequency: must be 4300000 + - spi-cpha: must be defined for max6675 to enable SPI mode 1 + + Refer to spi/spi-bus.txt for generic SPI slave bindings. + +Example: + + max31855@0 { + compatible = "maxim,max31855"; + reg = <0>; + spi-max-frequency = <4300000>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt b/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt index 1112e0d794e1..820fee4b77b6 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt @@ -13,6 +13,7 @@ Required properties: - touchscreen-size-y : See touchscreen.txt Optional properties: +- firmware-name : File basename (string) for board specific firmware - touchscreen-inverted-x : See touchscreen.txt - touchscreen-inverted-y : See touchscreen.txt - touchscreen-swapped-x-y : See touchscreen.txt diff --git a/Documentation/devicetree/bindings/interrupt-controller/jcore,aic.txt b/Documentation/devicetree/bindings/interrupt-controller/jcore,aic.txt new file mode 100644 index 000000000000..ee2ad36f8df8 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/jcore,aic.txt @@ -0,0 +1,26 @@ +J-Core Advanced Interrupt Controller + +Required properties: + +- compatible: Should be "jcore,aic1" for the (obsolete) first-generation aic + with 8 interrupt lines with programmable priorities, or "jcore,aic2" for + the "aic2" core with 64 interrupts. + +- reg: Memory region(s) for configuration. For SMP, there should be one + region per cpu, indexed by the sequential, zero-based hardware cpu + number. + +- interrupt-controller: Identifies the node as an interrupt controller + +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt source. The value shall be 1. + + +Example: + +aic: interrupt-controller@200 { + compatible = "jcore,aic2"; + reg = < 0x200 0x30 0x500 0x30 >; + interrupt-controller; + #interrupt-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/marvell,armada-8k-pic.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,armada-8k-pic.txt new file mode 100644 index 000000000000..86a7b4cd03f5 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/marvell,armada-8k-pic.txt @@ -0,0 +1,25 @@ +Marvell Armada 7K/8K PIC Interrupt controller +--------------------------------------------- + +This is the Device Tree binding for the PIC, a secondary interrupt +controller available on the Marvell Armada 7K/8K ARM64 SoCs, and +typically connected to the GIC as the primary interrupt controller. + +Required properties: +- compatible: should be "marvell,armada-8k-pic" +- interrupt-controller: identifies the node as an interrupt controller +- #interrupt-cells: the number of cells to define interrupts on this + controller. Should be 1 +- reg: the register area for the PIC interrupt controller +- interrupts: the interrupt to the primary interrupt controller, + typically the GIC + +Example: + + pic: interrupt-controller@3f0100 { + compatible = "marvell,armada-8k-pic"; + reg = <0x3f0100 0x10>; + #interrupt-cells = <1>; + interrupt-controller; + interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/marvell,odmi-controller.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,odmi-controller.txt index 8af0a8e613ab..3f6442c7f867 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/marvell,odmi-controller.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/marvell,odmi-controller.txt @@ -31,7 +31,7 @@ Required properties: Example: odmi: odmi@300000 { - compatible = "marvell,ap806-odm-controller", + compatible = "marvell,ap806-odmi-controller", "marvell,odmi-controller"; interrupt-controller; msi-controller; diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt index ae5054c27c99..e3f052d8c11a 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt @@ -1,10 +1,12 @@ -DT bindings for the R-Mobile/R-Car interrupt controller +DT bindings for the R-Mobile/R-Car/RZ/G interrupt controller Required properties: - compatible: has to be "renesas,irqc-<soctype>", "renesas,irqc" as fallback. Examples with soctypes are: - "renesas,irqc-r8a73a4" (R-Mobile APE6) + - "renesas,irqc-r8a7743" (RZ/G1M) + - "renesas,irqc-r8a7745" (RZ/G1E) - "renesas,irqc-r8a7790" (R-Car H2) - "renesas,irqc-r8a7791" (R-Car M2-W) - "renesas,irqc-r8a7792" (R-Car V2H) diff --git a/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt b/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt new file mode 100644 index 000000000000..6e7703d4ff5b --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt @@ -0,0 +1,20 @@ +STM32 External Interrupt Controller + +Required properties: + +- compatible: Should be "st,stm32-exti" +- reg: Specifies base physical address and size of the registers +- interrupt-controller: Indentifies the node as an interrupt controller +- #interrupt-cells: Specifies the number of cells to encode an interrupt + specifier, shall be 2 +- interrupts: interrupts references to primary interrupt controller + +Example: + +exti: interrupt-controller@40013c00 { + compatible = "st,stm32-exti"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x40013C00 0x400>; + interrupts = <1>, <2>, <3>, <6>, <7>, <8>, <9>, <10>, <23>, <40>, <41>, <42>, <62>, <76>; +}; diff --git a/Documentation/devicetree/bindings/leds/common.txt b/Documentation/devicetree/bindings/leds/common.txt index 93ef6e6e43b5..696be5792625 100644 --- a/Documentation/devicetree/bindings/leds/common.txt +++ b/Documentation/devicetree/bindings/leds/common.txt @@ -19,6 +19,13 @@ Optional properties for child nodes: a device, i.e. no other LED class device can be assigned the same label. +- default-state : The initial state of the LED. Valid values are "on", "off", + and "keep". If the LED is already on or off and the default-state property is + set the to same value, then no glitch should be produced where the LED + momentarily turns off (or on). The "keep" setting will keep the LED at + whatever its current state is, without producing a glitch. The default is + off if this property is not present. + - linux,default-trigger : This parameter, if present, is a string defining the trigger assigned to the LED. Current triggers are: "backlight" - LED will act as a back-light, controlled by the framebuffer diff --git a/Documentation/devicetree/bindings/leds/leds-bcm6328.txt b/Documentation/devicetree/bindings/leds/leds-bcm6328.txt index 3f48c1eaf085..ccebce597f37 100644 --- a/Documentation/devicetree/bindings/leds/leds-bcm6328.txt +++ b/Documentation/devicetree/bindings/leds/leds-bcm6328.txt @@ -49,7 +49,7 @@ LED sub-node optional properties: - active-low : Boolean, makes LED active low. Default : false - default-state : see - Documentation/devicetree/bindings/leds/leds-gpio.txt + Documentation/devicetree/bindings/leds/common.txt - linux,default-trigger : see Documentation/devicetree/bindings/leds/common.txt diff --git a/Documentation/devicetree/bindings/leds/leds-bcm6358.txt b/Documentation/devicetree/bindings/leds/leds-bcm6358.txt index b22a55bcc65d..da5708e7b43b 100644 --- a/Documentation/devicetree/bindings/leds/leds-bcm6358.txt +++ b/Documentation/devicetree/bindings/leds/leds-bcm6358.txt @@ -28,7 +28,7 @@ LED sub-node optional properties: - active-low : Boolean, makes LED active low. Default : false - default-state : see - Documentation/devicetree/bindings/leds/leds-gpio.txt + Documentation/devicetree/bindings/leds/common.txt - linux,default-trigger : see Documentation/devicetree/bindings/leds/common.txt diff --git a/Documentation/devicetree/bindings/leds/leds-gpio.txt b/Documentation/devicetree/bindings/leds/leds-gpio.txt index 5b1b43a64265..76535ca37120 100644 --- a/Documentation/devicetree/bindings/leds/leds-gpio.txt +++ b/Documentation/devicetree/bindings/leds/leds-gpio.txt @@ -14,13 +14,8 @@ LED sub-node properties: see Documentation/devicetree/bindings/leds/common.txt - linux,default-trigger : (optional) see Documentation/devicetree/bindings/leds/common.txt -- default-state: (optional) The initial state of the LED. Valid - values are "on", "off", and "keep". If the LED is already on or off - and the default-state property is set the to same value, then no - glitch should be produced where the LED momentarily turns off (or - on). The "keep" setting will keep the LED at whatever its current - state is, without producing a glitch. The default is off if this - property is not present. +- default-state: (optional) The initial state of the LED. + see Documentation/devicetree/bindings/leds/common.txt - retain-state-suspended: (optional) The suspend state can be retained.Such as charge-led gpio. - panic-indicator : (optional) diff --git a/Documentation/devicetree/bindings/leds/leds-is31fl319x.txt b/Documentation/devicetree/bindings/leds/leds-is31fl319x.txt new file mode 100644 index 000000000000..fc2603484544 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-is31fl319x.txt @@ -0,0 +1,59 @@ +LEDs connected to is31fl319x LED controller chip + +Required properties: +- compatible : Should be any of + "issi,is31fl3190" + "issi,is31fl3191" + "issi,is31fl3193" + "issi,is31fl3196" + "issi,is31fl3199" + "si-en,sn3199". +- #address-cells: Must be 1. +- #size-cells: Must be 0. +- reg: 0x64, 0x65, 0x66, or 0x67. + +Optional properties: +- audio-gain-db : audio gain selection for external analog modulation input. + Valid values: 0 - 21, step by 3 (rounded down) + Default: 0 + +Each led is represented as a sub-node of the issi,is31fl319x device. +There can be less leds subnodes than the chip can support but not more. + +Required led sub-node properties: +- reg : number of LED line + Valid values: 1 - number of leds supported by the chip variant. + +Optional led sub-node properties: +- label : see Documentation/devicetree/bindings/leds/common.txt. +- linux,default-trigger : + see Documentation/devicetree/bindings/leds/common.txt. +- led-max-microamp : (optional) + Valid values: 5000 - 40000, step by 5000 (rounded down) + Default: 20000 (20 mA) + Note: a driver will take the lowest of all led limits since the + chip has a single global setting. The lowest value will be chosen + due to the PWM specificity, where lower brightness is achieved + by reducing the dury-cycle of pulses and not the current, which + will always have its peak value equal to led-max-microamp. + +Examples: + +fancy_leds: leds@65 { + compatible = "issi,is31fl3196"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x65>; + + red_aux: led@1 { + label = "red:aux"; + reg = <1>; + led-max-microamp = <10000>; + }; + + green_power: led@5 { + label = "green:power"; + reg = <5>; + linux,default-trigger = "default-on"; + }; +}; diff --git a/Documentation/devicetree/bindings/leds/leds-pm8058.txt b/Documentation/devicetree/bindings/leds/leds-pm8058.txt new file mode 100644 index 000000000000..89584c49aab2 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-pm8058.txt @@ -0,0 +1,67 @@ +Qualcomm PM8058 LED driver + +The Qualcomm PM8058 is a multi-functional device which contains +an LED driver block for up to six LEDs: three normal LEDs, two +"flash" LEDs and one "keypad backlight" LED. The names are +quoted because sometimes these LED drivers are used for wildly +different things than flash or keypad backlight: their names +are more of a suggestion than a hard-wired usecase. + +Hardware-wise the different LEDs support slightly different +output currents. The "flash" LEDs do not need to charge nor +do they support external triggers. They are just powerful LED +drivers. + +The LEDs appear as children to the PM8058 device, with the +proper compatible string. For the PM8058 bindings see: +mfd/qcom-pm8xxx.txt. + +Each LED is represented as a sub-node of the syscon device. Each +node's name represents the name of the corresponding LED. + +LED sub-node properties: + +Required properties: +- compatible: one of + "qcom,pm8058-led" (for the normal LEDs at 0x131, 0x132 and 0x133) + "qcom,pm8058-keypad-led" (for the "keypad" LED at 0x48) + "qcom,pm8058-flash-led" (for the "flash" LEDs at 0x49 and 0xFB) + +Optional properties: +- label: see Documentation/devicetree/bindings/leds/common.txt +- default-state: see Documentation/devicetree/bindings/leds/common.txt +- linux,default-trigger: see Documentation/devicetree/bindings/leds/common.txt + +Example: + +qcom,ssbi@500000 { + pmicintc: pmic@0 { + compatible = "qcom,pm8058"; + led@48 { + compatible = "qcom,pm8058-keypad-led"; + reg = <0x48>; + label = "pm8050:white:keypad"; + default-state = "off"; + }; + led@131 { + compatible = "qcom,pm8058-led"; + reg = <0x131>; + label = "pm8058:red"; + default-state = "off"; + }; + led@132 { + compatible = "qcom,pm8058-led"; + reg = <0x132>; + label = "pm8058:yellow"; + default-state = "off"; + linux,default-trigger = "mmc0"; + }; + led@133 { + compatible = "qcom,pm8058-led"; + reg = <0x133>; + label = "pm8058:green"; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/leds/register-bit-led.txt b/Documentation/devicetree/bindings/leds/register-bit-led.txt index 379cefdc0bda..59b56365f648 100644 --- a/Documentation/devicetree/bindings/leds/register-bit-led.txt +++ b/Documentation/devicetree/bindings/leds/register-bit-led.txt @@ -23,13 +23,8 @@ Optional properties: see Documentation/devicetree/bindings/leds/common.txt - linux,default-trigger : (optional) see Documentation/devicetree/bindings/leds/common.txt -- default-state: (optional) The initial state of the LED. Valid - values are "on", "off", and "keep". If the LED is already on or off - and the default-state property is set the to same value, then no - glitch should be produced where the LED momentarily turns off (or - on). The "keep" setting will keep the LED at whatever its current - state is, without producing a glitch. The default is off if this - property is not present. +- default-state: (optional) The initial state of the LED + see Documentation/devicetree/bindings/leds/common.txt Example: diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mem-ctrlr.txt b/Documentation/devicetree/bindings/memory-controllers/fsl/ddr.txt index f87856faf1ab..dde6d837083a 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/mem-ctrlr.txt +++ b/Documentation/devicetree/bindings/memory-controllers/fsl/ddr.txt @@ -7,6 +7,8 @@ Properties: "fsl,qoriq-memory-controller". - reg : Address and size of DDR controller registers - interrupts : Error interrupt of DDR controller +- little-endian : Specifies little-endian access to registers + If omitted, big-endian will be used. Example 1: diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt index d3425846aa5b..6a1ae3a2b77f 100644 --- a/Documentation/devicetree/bindings/mfd/max77693.txt +++ b/Documentation/devicetree/bindings/mfd/max77693.txt @@ -17,28 +17,28 @@ Required properties: - interrupt-parent : The parent interrupt controller. Optional properties: -- regulators : The regulators of max77693 have to be instantiated under subnod +- regulators : The regulators of max77693 have to be instantiated under subnode named "regulators" using the following format. regulators { - regualtor-compatible = ESAFEOUT1/ESAFEOUT2/CHARGER - standard regulator constratints[*]. + regulator-compatible = ESAFEOUT1/ESAFEOUT2/CHARGER + standard regulator constraints[*]. }; [*] refer Documentation/devicetree/bindings/regulator/regulator.txt - haptic : The MAX77693 haptic device utilises a PWM controlled motor to provide users with tactile feedback. PWM period and duty-cycle are varied in - order to provide the approprite level of feedback. + order to provide the appropriate level of feedback. Required properties: - - compatible : Must be "maxim,max77693-hpatic" + - compatible : Must be "maxim,max77693-haptic" - haptic-supply : power supply for the haptic motor [*] refer Documentation/devicetree/bindings/regulator/regulator.txt - pwms : phandle to the physical PWM(Pulse Width Modulation) device. PWM properties should be named "pwms". And number of cell is different for each pwm device. - To get more informations, please refer to documentaion. + To get more information, please refer to documentation. [*] refer Documentation/devicetree/bindings/pwm/pwm.txt - charger : Node configuring the charger driver. diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt index 3fb68bfefc8b..f9065a5781a2 100644 --- a/Documentation/devicetree/bindings/mfd/stmpe.txt +++ b/Documentation/devicetree/bindings/mfd/stmpe.txt @@ -4,7 +4,7 @@ STMPE is an MFD device which may expose the following inbuilt devices: gpio, keypad, touchscreen, adc, pwm, rotator. Required properties: - - compatible : "st,stmpe[610|801|811|1601|2401|2403]" + - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]" - reg : I2C/SPI address of the device Optional properties: diff --git a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt index 3404afa9b938..49df630bd44f 100644 --- a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt @@ -36,6 +36,9 @@ Optional Properties: - #clock-cells: If specified this should be the value <0>. With this property in place we will export a clock representing the Card Clock. This clock is expected to be consumed by our PHY. You must also specify + - xlnx,fails-without-test-cd: when present, the controller doesn't work when + the CD line is not connected properly, and the line is not connected + properly. Test mode can be used to force the controller to function. Example: sdhci@e0100000 { diff --git a/Documentation/devicetree/bindings/mmc/brcm,bcm7425-sdhci.txt b/Documentation/devicetree/bindings/mmc/brcm,sdhci-brcmstb.txt index 82847174c37d..733b64a4d8eb 100644 --- a/Documentation/devicetree/bindings/mmc/brcm,bcm7425-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/brcm,sdhci-brcmstb.txt @@ -8,7 +8,9 @@ on Device Tree properties to enable them for SoC/Board combinations that support them. Required properties: -- compatible: "brcm,bcm7425-sdhci" +- compatible: should be one of the following + - "brcm,bcm7425-sdhci" + - "brcm,bcm7445-sdhci" Refer to clocks/clock-bindings.txt for generic clock consumer properties. diff --git a/Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.txt b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.txt index ce0e76749671..e25436861867 100644 --- a/Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.txt +++ b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.txt @@ -16,6 +16,8 @@ Optional properties: See ../clocks/clock-bindings.txt for details. - clock-names : Must include the following entry: "ext_clock" (External clock provided to the card). +- post-power-on-delay-ms : Delay in ms after powering the card and + de-asserting the reset-gpios (if any) Example: diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 22d1e1f3f38b..8a377827695b 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -75,6 +75,17 @@ Optional SDIO properties: - wakeup-source: Enables wake up of host system on SDIO IRQ assertion (Legacy property supported: "enable-sdio-wakeup") +MMC power +--------- + +Controllers may implement power control from both the connected cards and +the IO signaling (for example to change to high-speed 1.8V signalling). If +the system supports this, then the following two properties should point +to valid regulator nodes: + +- vqmmc-supply: supply node for IO line power +- vmmc-supply: supply node for card's power + MMC power sequences: -------------------- @@ -102,11 +113,13 @@ Required host node properties when using function subnodes: - #size-cells: should be zero. Required function subnode properties: -- compatible: name of SDIO function following generic names recommended practice - reg: Must contain the SDIO function number of the function this subnode describes. A value of 0 denotes the memory SD function, values from 1 to 7 denote the SDIO functions. +Optional function subnode properties: +- compatible: name of SDIO function following generic names recommended practice + Examples -------- diff --git a/Documentation/devicetree/bindings/mmc/sdhci-st.txt b/Documentation/devicetree/bindings/mmc/sdhci-st.txt index 88faa91125bf..3cd4c43a3260 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-st.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-st.txt @@ -10,7 +10,7 @@ Required properties: subsystem (mmcss) inside the FlashSS (available in STiH407 SoC family). -- clock-names: Should be "mmc". +- clock-names: Should be "mmc" and "icn". (NB: The latter is not compulsory) See: Documentation/devicetree/bindings/resource-names.txt - clocks: Phandle to the clock. See: Documentation/devicetree/bindings/clock/clock-bindings.txt diff --git a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt index 4bf41d833804..55cdd804cdba 100644 --- a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt +++ b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt @@ -8,7 +8,12 @@ as the speed of SD standard 3.0. Absolute maximum transfer rate is 200MB/s Required properties: - - compatible : "allwinner,sun4i-a10-mmc" or "allwinner,sun5i-a13-mmc" + - compatible : should be one of: + * "allwinner,sun4i-a10-mmc" + * "allwinner,sun5i-a13-mmc" + * "allwinner,sun7i-a20-mmc" + * "allwinner,sun9i-a80-mmc" + * "allwinner,sun50i-a64-mmc" - reg : mmc controller base registers - clocks : a list with 4 phandle + clock specifier pairs - clock-names : must contain "ahb", "mmc", "output" and "sample" diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt index 8636f5ae97e5..4e00e859e885 100644 --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt @@ -39,6 +39,10 @@ Required Properties: Optional properties: +* resets: phandle + reset specifier pair, intended to represent hardware + reset signal present internally in some host controller IC designs. + See Documentation/devicetree/bindings/reset/reset.txt for details. + * clocks: from common clock binding: handle to biu and ciu clocks for the bus interface unit clock and the card interface unit clock. diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index 0f610d4b5b00..13df9c2399c3 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -23,6 +23,7 @@ Required properties: "renesas,sdhi-r8a7793" - SDHI IP on R8A7793 SoC "renesas,sdhi-r8a7794" - SDHI IP on R8A7794 SoC "renesas,sdhi-r8a7795" - SDHI IP on R8A7795 SoC + "renesas,sdhi-r8a7796" - SDHI IP on R8A7796 SoC Optional properties: - toshiba,mmc-wrprotect-disable: write-protect detection is unavailable diff --git a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt index e41b2d59ca7f..f591ab782dbc 100644 --- a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt +++ b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt @@ -47,6 +47,9 @@ Optional properties: Valid values are between 0 to 7, that maps to 273, 589, 899, 1222, 1480, 1806, 2147, 2464 ps Default value is 2, which corresponds to 899 ps +- rxlos-gpios: Input gpio from SFP+ module to indicate availability of + incoming signal. + Example: menetclk: menetclk { diff --git a/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt b/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt index 30d487597ecb..fb40891ee606 100644 --- a/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt +++ b/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt @@ -6,9 +6,13 @@ Required properties: - reg: addresses and length of the register sets for the device, must be 6 pairs of register addresses and lengths - interrupts: interrupts for the devices, must be two interrupts +- #address-cells: must be 1, see dsa/dsa.txt +- #size-cells: must be 0, see dsa/dsa.txt + +Deprecated binding required properties: + - dsa,mii-bus: phandle to the MDIO bus controller, see dsa/dsa.txt - dsa,ethernet: phandle to the CPU network interface controller, see dsa/dsa.txt -- #size-cells: must be 0 - #address-cells: must be 2, see dsa/dsa.txt Subnodes: @@ -48,6 +52,45 @@ switch_top@f0b00000 { ethernet_switch@0 { compatible = "brcm,bcm7445-switch-v4.0"; #size-cells = <0>; + #address-cells = <1>; + reg = <0x0 0x40000 + 0x40000 0x110 + 0x40340 0x30 + 0x40380 0x30 + 0x40400 0x34 + 0x40600 0x208>; + reg-names = "core", "reg", intrl2_0", "intrl2_1", + "fcb, "acb"; + interrupts = <0 0x18 0 + 0 0x19 0>; + brcm,num-gphy = <1>; + brcm,num-rgmii-ports = <2>; + brcm,fcb-pause-override; + brcm,acb-packets-inflight; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + label = "gphy"; + reg = <0>; + }; + }; + }; +}; + +Example using the old DSA DeviceTree binding: + +switch_top@f0b00000 { + compatible = "simple-bus"; + #size-cells = <1>; + #address-cells = <1>; + ranges = <0 0xf0b00000 0x40804>; + + ethernet_switch@0 { + compatible = "brcm,bcm7445-switch-v4.0"; + #size-cells = <0>; #address-cells = <2>; reg = <0x0 0x40000 0x40000 0x110 diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.txt b/Documentation/devicetree/bindings/net/dsa/qca8k.txt new file mode 100644 index 000000000000..9c67ee4890d7 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt @@ -0,0 +1,89 @@ +* Qualcomm Atheros QCA8xxx switch family + +Required properties: + +- compatible: should be "qca,qca8337" +- #size-cells: must be 0 +- #address-cells: must be 1 + +Subnodes: + +The integrated switch subnode should be specified according to the binding +described in dsa/dsa.txt. As the QCA8K switches do not have a N:N mapping of +port and PHY id, each subnode describing a port needs to have a valid phandle +referencing the internal PHY connected to it. The CPU port of this switch is +always port 0. + +Example: + + + &mdio0 { + phy_port1: phy@0 { + reg = <0>; + }; + + phy_port2: phy@1 { + reg = <1>; + }; + + phy_port3: phy@2 { + reg = <2>; + }; + + phy_port4: phy@3 { + reg = <3>; + }; + + phy_port5: phy@4 { + reg = <4>; + }; + + switch0@0 { + compatible = "qca,qca8337"; + #address-cells = <1>; + #size-cells = <0>; + + reg = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "cpu"; + ethernet = <&gmac1>; + phy-mode = "rgmii"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + phy-handle = <&phy_port1>; + }; + + port@2 { + reg = <2>; + label = "lan2"; + phy-handle = <&phy_port2>; + }; + + port@3 { + reg = <3>; + label = "lan3"; + phy-handle = <&phy_port3>; + }; + + port@4 { + reg = <4>; + label = "lan4"; + phy-handle = <&phy_port4>; + }; + + port@5 { + reg = <5>; + label = "wan"; + phy-handle = <&phy_port5>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/ethernet.txt b/Documentation/devicetree/bindings/net/ethernet.txt index 5d88f37480b6..e1d76812419c 100644 --- a/Documentation/devicetree/bindings/net/ethernet.txt +++ b/Documentation/devicetree/bindings/net/ethernet.txt @@ -11,8 +11,8 @@ The following properties are common to the Ethernet controllers: the maximum frame size (there's contradiction in ePAPR). - phy-mode: string, operation mode of the PHY interface; supported values are "mii", "gmii", "sgmii", "qsgmii", "tbi", "rev-mii", "rmii", "rgmii", "rgmii-id", - "rgmii-rxid", "rgmii-txid", "rtbi", "smii", "xgmii"; this is now a de-facto - standard property; + "rgmii-rxid", "rgmii-txid", "rtbi", "smii", "xgmii", "trgmii"; this is now a + de-facto standard property; - phy-connection-type: the same as "phy-mode" property but described in ePAPR; - phy-handle: phandle, specifies a reference to a node representing a PHY device; this property is described in ePAPR and so preferred; diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index b5a42df4c928..1506e948610c 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -21,6 +21,7 @@ Required properties: - clock-names: Tuple listing input clock names. Required elements: 'pclk', 'hclk' Optional elements: 'tx_clk' + Optional elements: 'rx_clk' applies to cdns,zynqmp-gem - clocks: Phandles to input clocks. Optional properties for PHY child node: diff --git a/Documentation/devicetree/bindings/net/mediatek-net.txt b/Documentation/devicetree/bindings/net/mediatek-net.txt index 32eaaca04d9b..f09525772369 100644 --- a/Documentation/devicetree/bindings/net/mediatek-net.txt +++ b/Documentation/devicetree/bindings/net/mediatek-net.txt @@ -24,14 +24,17 @@ Required properties: Optional properties: - interrupt-parent: Should be the phandle for the interrupt controller that services interrupts for this device - +- mediatek,hwlro: the capability if the hardware supports LRO functions * Ethernet MAC node Required properties: - compatible: Should be "mediatek,eth-mac" - reg: The number of the MAC -- phy-handle: see ethernet.txt file in the same directory. +- phy-handle: see ethernet.txt file in the same directory and + the phy-mode "trgmii" required being provided when reg + is equal to 0 and the MAC uses fixed-link to connect + with internal switch such as MT7530. Example: @@ -51,6 +54,7 @@ eth: ethernet@1b100000 { reset-names = "eth"; mediatek,ethsys = <ðsys>; mediatek,pctl = <&syscfg_pctl_a>; + mediatek,hwlro; #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt new file mode 100644 index 000000000000..99c7eb0a00c8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt @@ -0,0 +1,58 @@ +* Microsemi - vsc8531 Giga bit ethernet phy + +Required properties: +- compatible : Should contain phy id as "ethernet-phy-idAAAA.BBBB" + The PHY device uses the binding described in + Documentation/devicetree/bindings/net/phy.txt + +Optional properties: +- vsc8531,vddmac : The vddmac in mV. +- vsc8531,edge-slowdown : % the edge should be slowed down relative to + the fastest possible edge time. Native sign + need not enter. + Edge rate sets the drive strength of the MAC + interface output signals. Changing the drive + strength will affect the edge rate of the output + signal. The goal of this setting is to help + reduce electrical emission (EMI) by being able + to reprogram drive strength and in effect slow + down the edge rate if desired. Table 1 shows the + impact to the edge rate per VDDMAC supply for each + drive strength setting. + Ref: Table:1 - Edge rate change below. + +Note: see dt-bindings/net/mscc-phy-vsc8531.h for applicable values + +Table: 1 - Edge rate change +----------------------------------------------------------------| +| Edge Rate Change (VDDMAC) | +| | +| 3300 mV 2500 mV 1800 mV 1500 mV | +|---------------------------------------------------------------| +| Default Deafult Default Default | +| (Fastest) (recommended) (recommended) | +|---------------------------------------------------------------| +| -2% -3% -5% -6% | +|---------------------------------------------------------------| +| -4% -6% -9% -14% | +|---------------------------------------------------------------| +| -7% -10% -16% -21% | +|(recommended) (recommended) | +|---------------------------------------------------------------| +| -10% -14% -23% -29% | +|---------------------------------------------------------------| +| -17% -23% -35% -42% | +|---------------------------------------------------------------| +| -29% -37% -52% -58% | +|---------------------------------------------------------------| +| -53% -63% -76% -77% | +| (slowest) | +|---------------------------------------------------------------| + +Example: + + vsc8531_0: ethernet-phy@0 { + compatible = "ethernet-phy-id0007.0570"; + vsc8531,vddmac = <3300>; + vsc8531,edge-slowdown = <21>; + }; diff --git a/Documentation/devicetree/bindings/net/qcom-emac.txt b/Documentation/devicetree/bindings/net/qcom-emac.txt new file mode 100644 index 000000000000..346e6c7f47b7 --- /dev/null +++ b/Documentation/devicetree/bindings/net/qcom-emac.txt @@ -0,0 +1,111 @@ +Qualcomm Technologies EMAC Gigabit Ethernet Controller + +This network controller consists of two devices: a MAC and an SGMII +internal PHY. Each device is represented by a device tree node. A phandle +connects the MAC node to its corresponding internal phy node. Another +phandle points to the external PHY node. + +Required properties: + +MAC node: +- compatible : Should be "qcom,fsm9900-emac". +- reg : Offset and length of the register regions for the device +- interrupts : Interrupt number used by this controller +- mac-address : The 6-byte MAC address. If present, it is the default + MAC address. +- internal-phy : phandle to the internal PHY node +- phy-handle : phandle the the external PHY node + +Internal PHY node: +- compatible : Should be "qcom,fsm9900-emac-sgmii" or "qcom,qdf2432-emac-sgmii". +- reg : Offset and length of the register region(s) for the device +- interrupts : Interrupt number used by this controller + +The external phy child node: +- reg : The phy address + +Example: + +FSM9900: + +soc { + #address-cells = <1>; + #size-cells = <1>; + + emac0: ethernet@feb20000 { + compatible = "qcom,fsm9900-emac"; + reg = <0xfeb20000 0x10000>, + <0xfeb36000 0x1000>; + interrupts = <76>; + + clocks = <&gcc 0>, <&gcc 1>, <&gcc 3>, <&gcc 4>, <&gcc 5>, + <&gcc 6>, <&gcc 7>; + clock-names = "axi_clk", "cfg_ahb_clk", "high_speed_clk", + "mdio_clk", "tx_clk", "rx_clk", "sys_clk"; + + internal-phy = <&emac_sgmii>; + + phy-handle = <&phy0>; + + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@0 { + reg = <0>; + }; + + pinctrl-names = "default"; + pinctrl-0 = <&mdio_pins_a>; + }; + + emac_sgmii: ethernet@feb38000 { + compatible = "qcom,fsm9900-emac-sgmii"; + reg = <0xfeb38000 0x1000>; + interrupts = <80>; + }; + + tlmm: pinctrl@fd510000 { + compatible = "qcom,fsm9900-pinctrl"; + + mdio_pins_a: mdio { + state { + pins = "gpio123", "gpio124"; + function = "mdio"; + }; + }; + }; + + +QDF2432: + +soc { + #address-cells = <2>; + #size-cells = <2>; + + emac0: ethernet@38800000 { + compatible = "qcom,fsm9900-emac"; + reg = <0x0 0x38800000 0x0 0x10000>, + <0x0 0x38816000 0x0 0x1000>; + interrupts = <0 256 4>; + + clocks = <&gcc 0>, <&gcc 1>, <&gcc 3>, <&gcc 4>, <&gcc 5>, + <&gcc 6>, <&gcc 7>; + clock-names = "axi_clk", "cfg_ahb_clk", "high_speed_clk", + "mdio_clk", "tx_clk", "rx_clk", "sys_clk"; + + internal-phy = <&emac_sgmii>; + + phy-handle = <&phy0>; + + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@4 { + reg = <4>; + }; + }; + + emac_sgmii: ethernet@410400 { + compatible = "qcom,qdf2432-emac-sgmii"; + reg = <0x0 0x00410400 0x0 0xc00>, /* Base address */ + <0x0 0x00410000 0x0 0x400>; /* Per-lane digital */ + interrupts = <0 254 1>; + }; diff --git a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt index cccd945fc45b..95383c5131fc 100644 --- a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt +++ b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt @@ -3,8 +3,12 @@ Rockchip SoC RK3288 10/100/1000 Ethernet driver(GMAC) The device node has following properties. Required properties: - - compatible: Can be one of "rockchip,rk3228-gmac", "rockchip,rk3288-gmac", - "rockchip,rk3368-gmac" + - compatible: should be "rockchip,<name>-gamc" + "rockchip,rk3228-gmac": found on RK322x SoCs + "rockchip,rk3288-gmac": found on RK3288 SoCs + "rockchip,rk3366-gmac": found on RK3366 SoCs + "rockchip,rk3368-gmac": found on RK3368 SoCs + "rockchip,rk3399-gmac": found on RK3399 SoCs - reg: addresses and length of the register sets for the device. - interrupts: Should contain the GMAC interrupts. - interrupt-names: Should contain the interrupt names "macirq". diff --git a/Documentation/devicetree/bindings/net/sh_eth.txt b/Documentation/devicetree/bindings/net/sh_eth.txt index 2f6ec85fda8e..0115c85a2425 100644 --- a/Documentation/devicetree/bindings/net/sh_eth.txt +++ b/Documentation/devicetree/bindings/net/sh_eth.txt @@ -5,6 +5,8 @@ interface contains. Required properties: - compatible: "renesas,gether-r8a7740" if the device is a part of R8A7740 SoC. + "renesas,ether-r8a7743" if the device is a part of R8A7743 SoC. + "renesas,ether-r8a7745" if the device is a part of R8A7745 SoC. "renesas,ether-r8a7778" if the device is a part of R8A7778 SoC. "renesas,ether-r8a7779" if the device is a part of R8A7779 SoC. "renesas,ether-r8a7790" if the device is a part of R8A7790 SoC. diff --git a/Documentation/devicetree/bindings/net/smsc911x.txt b/Documentation/devicetree/bindings/net/smsc911x.txt index 3fed3c124411..16c3a9501f5d 100644 --- a/Documentation/devicetree/bindings/net/smsc911x.txt +++ b/Documentation/devicetree/bindings/net/smsc911x.txt @@ -3,9 +3,11 @@ Required properties: - compatible : Should be "smsc,lan<model>", "smsc,lan9115" - reg : Address and length of the io space for SMSC LAN -- interrupts : Should contain SMSC LAN interrupt line -- interrupt-parent : Should be the phandle for the interrupt controller - that services interrupts for this device +- interrupts : one or two interrupt specifiers + - The first interrupt is the SMSC LAN interrupt line + - The second interrupt (if present) is the PME (power + management event) interrupt that is able to wake up the host + system with a 50ms pulse on network activity - phy-mode : See ethernet.txt file in the same directory Optional properties: @@ -21,6 +23,10 @@ Optional properties: external PHY - smsc,save-mac-address : Indicates that mac address needs to be saved before resetting the controller +- reset-gpios : a GPIO line connected to the RESET (active low) signal + of the device. On many systems this is wired high so the device goes + out of reset at power-on, but if it is under program control, this + optional GPIO can wake up in response to it. Examples: @@ -29,7 +35,8 @@ lan9220@f4000000 { reg = <0xf4000000 0x2000000>; phy-mode = "mii"; interrupt-parent = <&gpio1>; - interrupts = <31>; + interrupts = <31>, <32>; + reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; reg-io-width = <4>; smsc,irq-push-pull; }; diff --git a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt index 51f8d2eba8d8..d93f71ce8346 100644 --- a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt +++ b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt @@ -1,21 +1,111 @@ * Synopsys DWC Ethernet QoS IP version 4.10 driver (GMAC) +This binding supports the Synopsys Designware Ethernet QoS (Quality Of Service) +IP block. The IP supports multiple options for bus type, clocking and reset +structure, and feature list. Consequently, a number of properties and list +entries in properties are marked as optional, or only required in specific HW +configurations. Required properties: -- compatible: Should be "snps,dwc-qos-ethernet-4.10" +- compatible: One of: + - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10" + Represents the IP core when integrated into the Axis ARTPEC-6 SoC. + - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10" + Represents the IP core when integrated into the NVIDIA Tegra186 SoC. + - "snps,dwc-qos-ethernet-4.10" + This combination is deprecated. It should be treated as equivalent to + "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10". It is supported to be + compatible with earlier revisions of this binding. - reg: Address and length of the register set for the device -- clocks: Phandles to the reference clock and the bus clock -- clock-names: Should be "phy_ref_clk" for the reference clock and "apb_pclk" - for the bus clock. +- clocks: Phandle and clock specifiers for each entry in clock-names, in the + same order. See ../clock/clock-bindings.txt. +- clock-names: May contain any/all of the following depending on the IP + configuration, in any order: + - "tx" + The EQOS transmit path clock. The HW signal name is clk_tx_i. + In some configurations (e.g. GMII/RGMII), this clock also drives the PHY TX + path. In other configurations, other clocks (such as tx_125, rmii) may + drive the PHY TX path. + - "rx" + The EQOS receive path clock. The HW signal name is clk_rx_i. + In some configurations (e.g. GMII/RGMII), this clock is derived from the + PHY's RX clock output. In other configurations, other clocks (such as + rx_125, rmii) may drive the EQOS RX path. + In cases where the PHY clock is directly fed into the EQOS receive path + without intervening logic, the DT need not represent this clock, since it + is assumed to be fully under the control of the PHY device/driver. In + cases where SoC integration adds additional logic to this path, such as a + SW-controlled clock gate, this clock should be represented in DT. + - "slave_bus" + The CPU/slave-bus (CSR) interface clock. This applies to any bus type; + APB, AHB, AXI, etc. The HW signal name is hclk_i (AHB) or clk_csr_i (other + buses). + - "master_bus" + The master bus interface clock. Only required in configurations that use a + separate clock for the master and slave bus interfaces. The HW signal name + is hclk_i (AHB) or aclk_i (AXI). + - "ptp_ref" + The PTP reference clock. The HW signal name is clk_ptp_ref_i. + - "phy_ref_clk" + This clock is deprecated and should not be used by new compatible values. + It is equivalent to "tx". + - "apb_pclk" + This clock is deprecated and should not be used by new compatible values. + It is equivalent to "slave_bus". + + Note: Support for additional IP configurations may require adding the + following clocks to this list in the future: clk_rx_125_i, clk_tx_125_i, + clk_pmarx_0_i, clk_pmarx1_i, clk_rmii_i, clk_revmii_rx_i, clk_revmii_tx_i. + Configurations exist where multiple similar clocks are used at once, e.g. all + of clk_rx_125_i, clk_pmarx_0_i, clk_pmarx1_i. For this reason it is best to + extend the binding with a separate clock-names entry for each of those RX + clocks, rather than repurposing the existing "rx" clock-names entry as a + generic/logical clock in a similar fashion to "master_bus" and "slave_bus". + This will allow easy support for configurations that support multiple PHY + interfaces using a mux, and hence need to have explicit control over + specific RX clocks. + + The following compatible values require the following set of clocks: + - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10": + - "slave_bus" + - "master_bus" + - "rx" + - "tx" + - "ptp_ref" + - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10": + - "slave_bus" + - "master_bus" + - "tx" + - "ptp_ref" + - "snps,dwc-qos-ethernet-4.10" (deprecated): + - "phy_ref_clk" + - "apb_clk" - interrupt-parent: Should be the phandle for the interrupt controller that services interrupts for this device - interrupts: Should contain the core's combined interrupt signal - phy-mode: See ethernet.txt file in the same directory +- resets: Phandle and reset specifiers for each entry in reset-names, in the + same order. See ../reset/reset.txt. +- reset-names: May contain any/all of the following depending on the IP + configuration, in any order: + - "eqos". The reset to the entire module. The HW signal name is hreset_n + (AHB) or aresetn_i (AXI). + + The following compatible values require the following set of resets: + (the reset properties may be omitted if empty) + - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10": + - "eqos". + - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10": + - None. + - "snps,dwc-qos-ethernet-4.10" (deprecated): + - None. Optional properties: - dma-coherent: Present if dma operations are coherent - mac-address: See ethernet.txt in the same directory - local-mac-address: See ethernet.txt in the same directory +- phy-reset-gpios: Phandle and specifier for any GPIO used to reset the PHY. + See ../gpio/gpio.txt. - snps,en-lpi: If present it enables use of the AXI low-power interface - snps,write-requests: Number of write requests that the AXI port can issue. It depends on the SoC configuration. @@ -52,6 +142,7 @@ ethernet2@40010000 { reg = <0x40010000 0x4000>; phy-handle = <&phy2>; phy-mode = "gmii"; + phy-reset-gpios = <&gpioctlr 43 GPIO_ACTIVE_LOW>; snps,en-tx-lpi-clockgating; snps,en-lpi; diff --git a/Documentation/devicetree/bindings/net/stm32-dwmac.txt b/Documentation/devicetree/bindings/net/stm32-dwmac.txt new file mode 100644 index 000000000000..c35afb7e956a --- /dev/null +++ b/Documentation/devicetree/bindings/net/stm32-dwmac.txt @@ -0,0 +1,32 @@ +STMicroelectronics STM32 / MCU DWMAC glue layer controller + +This file documents platform glue layer for stmmac. +Please see stmmac.txt for the other unchanged properties. + +The device node has following properties. + +Required properties: +- compatible: Should be "st,stm32-dwmac" to select glue, and + "snps,dwmac-3.50a" to select IP version. +- clocks: Must contain a phandle for each entry in clock-names. +- clock-names: Should be "stmmaceth" for the host clock. + Should be "mac-clk-tx" for the MAC TX clock. + Should be "mac-clk-rx" for the MAC RX clock. +- st,syscon : Should be phandle/offset pair. The phandle to the syscon node which + encompases the glue register, and the offset of the control register. +Example: + + ethernet@40028000 { + compatible = "st,stm32-dwmac", "snps,dwmac-3.50a"; + status = "disabled"; + reg = <0x40028000 0x8000>; + reg-names = "stmmaceth"; + interrupts = <0 61 0>, <0 62 0>; + interrupt-names = "macirq", "eth_wake_irq"; + clock-names = "stmmaceth", "mac-clk-tx", "mac-clk-rx"; + clocks = <&rcc 0 25>, <&rcc 0 26>, <&rcc 0 27>; + st,syscon = <&syscfg 0x4>; + snps,pbl = <8>; + snps,mixed-burst; + dma-ranges; + }; diff --git a/Documentation/devicetree/bindings/net/wireless/esp,esp8089.txt b/Documentation/devicetree/bindings/net/wireless/esp,esp8089.txt new file mode 100644 index 000000000000..19331bb4ff6e --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/esp,esp8089.txt @@ -0,0 +1,31 @@ +Espressif ESP8089 wireless SDIO devices + +This node provides properties for controlling the ESP8089 wireless device. +The node is expected to be specified as a child node to the SDIO controller +that connects the device to the system. + +Required properties: + + - compatible : Should be "esp,esp8089". + +Optional properties: + - esp,crystal-26M-en: Integer value for the crystal_26M_en firmware parameter + +Example: + +&mmc1 { + #address-cells = <1>; + #size-cells = <0>; + + vmmc-supply = <®_dldo1>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + esp8089: sdio_wifi@1 { + compatible = "esp,esp8089"; + reg = <1>; + esp,crystal-26M-en = <2>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/xilinx_gmii2rgmii.txt b/Documentation/devicetree/bindings/net/xilinx_gmii2rgmii.txt new file mode 100644 index 000000000000..038dda48b8e6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/xilinx_gmii2rgmii.txt @@ -0,0 +1,35 @@ +XILINX GMIITORGMII Converter Driver Device Tree Bindings +-------------------------------------------------------- + +The Gigabit Media Independent Interface (GMII) to Reduced Gigabit Media +Independent Interface (RGMII) core provides the RGMII between RGMII-compliant +Ethernet physical media devices (PHY) and the Gigabit Ethernet controller. +This core can be used in all three modes of operation(10/100/1000 Mb/s). +The Management Data Input/Output (MDIO) interface is used to configure the +Speed of operation. This core can switch dynamically between the three +Different speed modes by configuring the conveter register through mdio write. + +This converter sits between the ethernet MAC and the external phy. +MAC <==> GMII2RGMII <==> RGMII_PHY + +For more details about mdio please refer phy.txt file in the same directory. + +Required properties: +- compatible : Should be "xlnx,gmii-to-rgmii-1.0" +- reg : The ID number for the phy, usually a small integer +- phy-handle : Should point to the external phy device. + See ethernet.txt file in the same directory. + +Example: + mdio { + #address-cells = <1>; + #size-cells = <0>; + phy: ethernet-phy@0 { + ...... + }; + gmiitorgmii: gmiitorgmii@8 { + compatible = "xlnx,gmii-to-rgmii-1.0"; + reg = <8>; + phy-handle = <&phy>; + }; + }; diff --git a/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt b/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt index 8f86ab3b1046..94aeeeabadd5 100644 --- a/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt +++ b/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt @@ -1,11 +1,20 @@ = Rockchip eFuse device tree bindings = Required properties: -- compatible: Should be "rockchip,rockchip-efuse" +- compatible: Should be one of the following. + - "rockchip,rk3066a-efuse" - for RK3066a SoCs. + - "rockchip,rk3188-efuse" - for RK3188 SoCs. + - "rockchip,rk3288-efuse" - for RK3288 SoCs. + - "rockchip,rk3399-efuse" - for RK3399 SoCs. - reg: Should contain the registers location and exact eFuse size - clocks: Should be the clock id of eFuse - clock-names: Should be "pclk_efuse" +Deprecated properties: +- compatible: "rockchip,rockchip-efuse" + Old efuse compatible value compatible to rk3066a, rk3188 and rk3288 + efuses + = Data cells = Are child nodes of eFuse, bindings of which as described in bindings/nvmem/nvmem.txt @@ -13,7 +22,7 @@ bindings/nvmem/nvmem.txt Example: efuse: efuse@ffb40000 { - compatible = "rockchip,rockchip-efuse"; + compatible = "rockchip,rk3288-efuse"; reg = <0xffb40000 0x20>; #address-cells = <1>; #size-cells = <1>; diff --git a/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt b/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt index 330a45b5f0b5..5ecaea1e6eee 100644 --- a/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt +++ b/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt @@ -24,16 +24,17 @@ Example: compatible = "axis,artpec6-pcie", "snps,dw-pcie"; reg = <0xf8050000 0x2000 0xf8040000 0x1000 - 0xc0000000 0x1000>; + 0xc0000000 0x2000>; reg-names = "dbi", "phy", "config"; #address-cells = <3>; #size-cells = <2>; device_type = "pci"; /* downstream I/O */ - ranges = <0x81000000 0 0x00010000 0xc0010000 0 0x00010000 + ranges = <0x81000000 0 0 0xc0002000 0 0x00010000 /* non-prefetchable memory */ - 0x82000000 0 0xc0020000 0xc0020000 0 0x1ffe0000>; + 0x82000000 0 0xc0012000 0xc0012000 0 0x1ffee000>; num-lanes = <2>; + bus-range = <0x00 0xff>; interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "msi"; #interrupt-cells = <1>; diff --git a/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt b/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt index 337fc97d18c9..3259798a1192 100644 --- a/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt +++ b/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt @@ -55,9 +55,10 @@ nwl_pcie: pcie@fd0e0000 { msi-parent = <&nwl_pcie>; reg = <0x0 0xfd0e0000 0x0 0x1000>, <0x0 0xfd480000 0x0 0x1000>, - <0x0 0xe0000000 0x0 0x1000000>; + <0x80 0x00000000 0x0 0x1000000>; reg-names = "breg", "pcireg", "cfg"; - ranges = <0x02000000 0x00000000 0xe1000000 0x00000000 0xe1000000 0 0x0f000000>; + ranges = <0x02000000 0x00000000 0xe0000000 0x00000000 0xe0000000 0x00000000 0x10000000 /* non-prefetchable memory */ + 0x43000000 0x00000006 0x00000000 0x00000006 0x00000000 0x00000002 0x00000000>;/* prefetchable memory */ pcie_intc: legacy-interrupt-controller { interrupt-controller; diff --git a/Documentation/devicetree/bindings/phy/bcm-ns-usb3-phy.txt b/Documentation/devicetree/bindings/phy/bcm-ns-usb3-phy.txt new file mode 100644 index 000000000000..09aeba94538d --- /dev/null +++ b/Documentation/devicetree/bindings/phy/bcm-ns-usb3-phy.txt @@ -0,0 +1,23 @@ +Driver for Broadcom Northstar USB 3.0 PHY + +Required properties: + +- compatible: one of: "brcm,ns-ax-usb3-phy", "brcm,ns-bx-usb3-phy". +- reg: register mappings for DMP (Device Management Plugin) and ChipCommon B + MMI. +- reg-names: "dmp" and "ccb-mii" + +Initialization of USB 3.0 PHY depends on Northstar version. There are currently +three known series: Ax, Bx and Cx. +Known A0: BCM4707 rev 0 +Known B0: BCM4707 rev 4, BCM53573 rev 2 +Known B1: BCM4707 rev 6 +Known C0: BCM47094 rev 0 + +Example: + usb3-phy { + compatible = "brcm,ns-ax-usb3-phy"; + reg = <0x18105000 0x1000>, <0x18003000 0x1000>; + reg-names = "dmp", "ccb-mii"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt b/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt index 379b84a567cc..1d25b04cd05e 100644 --- a/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt @@ -12,6 +12,16 @@ Required properties: - interrupts: Should contain phy interrupt - fsl,anatop: phandle for anatop register, it is only for imx6 SoC series +Optional properties: +- fsl,tx-cal-45-dn-ohms: Integer [30-55]. Resistance (in ohms) of switchable + high-speed trimming resistor connected in parallel with the 45 ohm resistor + that terminates the DN output signal. Default: 45 +- fsl,tx-cal-45-dp-ohms: Integer [30-55]. Resistance (in ohms) of switchable + high-speed trimming resistor connected in parallel with the 45 ohm resistor + that terminates the DP output signal. Default: 45 +- fsl,tx-d-cal: Integer [79-119]. Current trimming value (as a percentage) of + the 17.78mA TX reference current. Default: 100 + Example: usbphy1: usbphy@020c9000 { compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy"; diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt new file mode 100644 index 000000000000..3c29c77a7018 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt @@ -0,0 +1,64 @@ +ROCKCHIP USB2.0 PHY WITH INNO IP BLOCK + +Required properties (phy (parent) node): + - compatible : should be one of the listed compatibles: + * "rockchip,rk3366-usb2phy" + * "rockchip,rk3399-usb2phy" + - reg : the address offset of grf for usb-phy configuration. + - #clock-cells : should be 0. + - clock-output-names : specify the 480m output clock name. + +Optional properties: + - clocks : phandle + phy specifier pair, for the input clock of phy. + - clock-names : input clock name of phy, must be "phyclk". + +Required nodes : a sub-node is required for each port the phy provides. + The sub-node name is used to identify host or otg port, + and shall be the following entries: + * "otg-port" : the name of otg port. + * "host-port" : the name of host port. + +Required properties (port (child) node): + - #phy-cells : must be 0. See ./phy-bindings.txt for details. + - interrupts : specify an interrupt for each entry in interrupt-names. + - interrupt-names : a list which shall be the following entries: + * "otg-id" : for the otg id interrupt. + * "otg-bvalid" : for the otg vbus interrupt. + * "linestate" : for the host/otg linestate interrupt. + +Optional properties: + - phy-supply : phandle to a regulator that provides power to VBUS. + See ./phy-bindings.txt for details. + +Example: + +grf: syscon@ff770000 { + compatible = "rockchip,rk3366-grf", "syscon", "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + +... + + u2phy: usb2-phy@700 { + compatible = "rockchip,rk3366-usb2phy"; + reg = <0x700 0x2c>; + #clock-cells = <0>; + clock-output-names = "sclk_otgphy0_480m"; + + u2phy_otg: otg-port { + #phy-cells = <0>; + interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "otg-id", "otg-bvalid", "linestate"; + status = "okay"; + }; + + u2phy_host: host-port { + #phy-cells = <0>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "linestate"; + status = "okay"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt new file mode 100644 index 000000000000..6ea867e3176f --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt @@ -0,0 +1,101 @@ +* ROCKCHIP type-c PHY +--------------------- + +Required properties: + - compatible : must be "rockchip,rk3399-typec-phy" + - reg: Address and length of the usb phy control register set + - rockchip,grf : phandle to the syscon managing the "general + register files" + - clocks : phandle + clock specifier for the phy clocks + - clock-names : string, clock name, must be "tcpdcore", "tcpdphy-ref"; + - assigned-clocks: main clock, should be <&cru SCLK_UPHY0_TCPDCORE> or + <&cru SCLK_UPHY1_TCPDCORE>; + - assigned-clock-rates : the phy core clk frequency, shall be: 50000000 + - resets : a list of phandle + reset specifier pairs + - reset-names : string reset name, must be: + "uphy", "uphy-pipe", "uphy-tcphy" + - extcon : extcon specifier for the Power Delivery + +Note, there are 2 type-c phys for RK3399, and they are almost identical, except +these registers(description below), every register node contains 3 sections: +offset, enable bit, write mask bit. + - rockchip,typec-conn-dir : the register of type-c connector direction, + for type-c phy0, it must be <0xe580 0 16>; + for type-c phy1, it must be <0xe58c 0 16>; + - rockchip,usb3tousb2-en : the register of type-c force usb3 to usb2 enable + control. + for type-c phy0, it must be <0xe580 3 19>; + for type-c phy1, it must be <0xe58c 3 19>; + - rockchip,external-psm : the register of type-c phy external psm clock + selection. + for type-c phy0, it must be <0xe588 14 30>; + for type-c phy1, it must be <0xe594 14 30>; + - rockchip,pipe-status : the register of type-c phy pipe status. + for type-c phy0, it must be <0xe5c0 0 0>; + for type-c phy1, it must be <0xe5c0 16 16>; + +Required nodes : a sub-node is required for each port the phy provides. + The sub-node name is used to identify dp or usb3 port, + and shall be the following entries: + * "dp-port" : the name of DP port. + * "usb3-port" : the name of USB3 port. + +Required properties (port (child) node): +- #phy-cells : must be 0, See ./phy-bindings.txt for details. + +Example: + tcphy0: phy@ff7c0000 { + compatible = "rockchip,rk3399-typec-phy"; + reg = <0x0 0xff7c0000 0x0 0x40000>; + rockchip,grf = <&grf>; + extcon = <&fusb0>; + clocks = <&cru SCLK_UPHY0_TCPDCORE>, + <&cru SCLK_UPHY0_TCPDPHY_REF>; + clock-names = "tcpdcore", "tcpdphy-ref"; + assigned-clocks = <&cru SCLK_UPHY0_TCPDCORE>; + assigned-clock-rates = <50000000>; + resets = <&cru SRST_UPHY0>, + <&cru SRST_UPHY0_PIPE_L00>, + <&cru SRST_P_UPHY0_TCPHY>; + reset-names = "uphy", "uphy-pipe", "uphy-tcphy"; + rockchip,typec-conn-dir = <0xe580 0 16>; + rockchip,usb3tousb2-en = <0xe580 3 19>; + rockchip,external-psm = <0xe588 14 30>; + rockchip,pipe-status = <0xe5c0 0 0>; + + tcphy0_dp: dp-port { + #phy-cells = <0>; + }; + + tcphy0_usb3: usb3-port { + #phy-cells = <0>; + }; + }; + + tcphy1: phy@ff800000 { + compatible = "rockchip,rk3399-typec-phy"; + reg = <0x0 0xff800000 0x0 0x40000>; + rockchip,grf = <&grf>; + extcon = <&fusb1>; + clocks = <&cru SCLK_UPHY1_TCPDCORE>, + <&cru SCLK_UPHY1_TCPDPHY_REF>; + clock-names = "tcpdcore", "tcpdphy-ref"; + assigned-clocks = <&cru SCLK_UPHY1_TCPDCORE>; + assigned-clock-rates = <50000000>; + resets = <&cru SRST_UPHY1>, + <&cru SRST_UPHY1_PIPE_L00>, + <&cru SRST_P_UPHY1_TCPHY>; + reset-names = "uphy", "uphy-pipe", "uphy-tcphy"; + rockchip,typec-conn-dir = <0xe58c 0 16>; + rockchip,usb3tousb2-en = <0xe58c 3 19>; + rockchip,external-psm = <0xe594 14 30>; + rockchip,pipe-status = <0xe5c0 16 16>; + + tcphy1_dp: dp-port { + #phy-cells = <0>; + }; + + tcphy1_usb3: usb3-port { + #phy-cells = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt index 2281d6cdecb1..ace9cce2704a 100644 --- a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt +++ b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt @@ -6,6 +6,8 @@ This file provides information on what the device node for the R-Car generation Required properties: - compatible: "renesas,usb2-phy-r8a7795" if the device is a part of an R8A7795 SoC. + "renesas,usb2-phy-r8a7796" if the device is a part of an R8A7796 + SoC. "renesas,rcar-gen3-usb2-phy" for a generic R-Car Gen3 compatible device. When compatible with the generic version, nodes must list the @@ -30,11 +32,11 @@ Example (R-Car H3): compatible = "renesas,usb2-phy-r8a7795", "renesas,rcar-gen3-usb2-phy"; reg = <0 0xee080200 0 0x700>; interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp7_clks R8A7795_CLK_EHCI0>; + clocks = <&cpg CPG_MOD 703>; }; usb-phy@ee0a0200 { compatible = "renesas,usb2-phy-r8a7795", "renesas,rcar-gen3-usb2-phy"; reg = <0 0xee0a0200 0 0x700>; - clocks = <&mstp7_clks R8A7795_CLK_EHCI0>; + clocks = <&cpg CPG_MOD 702>; }; diff --git a/Documentation/devicetree/bindings/phy/rockchip-pcie-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-pcie-phy.txt new file mode 100644 index 000000000000..0f6222a672ce --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rockchip-pcie-phy.txt @@ -0,0 +1,31 @@ +Rockchip PCIE PHY +----------------------- + +Required properties: + - compatible: rockchip,rk3399-pcie-phy + - #phy-cells: must be 0 + - clocks: Must contain an entry in clock-names. + See ../clocks/clock-bindings.txt for details. + - clock-names: Must be "refclk" + - resets: Must contain an entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must be "phy" + +Example: + +grf: syscon@ff770000 { + compatible = "rockchip,rk3399-grf", "syscon", "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + + ... + + pcie_phy: pcie-phy { + compatible = "rockchip,rk3399-pcie-phy"; + #phy-cells = <0>; + clocks = <&cru SCLK_PCIEPHY_REF>; + clock-names = "refclk"; + resets = <&cru SRST_PCIEPHY>; + reset-names = "phy"; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt index cc6be9680a6d..57dc388e2fa2 100644 --- a/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt @@ -27,6 +27,9 @@ Optional Properties: - clocks : phandle + clock specifier for the phy clocks - clock-names: string, clock name, must be "phyclk" - #clock-cells: for users of the phy-pll, should be 0 +- reset-names: Only allow the following entries: + - phy-reset +- resets: Must contain an entry for each entry in reset-names. Example: diff --git a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt index 95736d77fbb7..287150db6db4 100644 --- a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt @@ -10,6 +10,7 @@ Required properties: * allwinner,sun8i-a23-usb-phy * allwinner,sun8i-a33-usb-phy * allwinner,sun8i-h3-usb-phy + * allwinner,sun50i-a64-usb-phy - reg : a list of offset + length pairs - reg-names : * "phy_ctrl" diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt index a3b394587874..cd13e6157088 100644 --- a/Documentation/devicetree/bindings/phy/ti-phy.txt +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt @@ -31,6 +31,8 @@ OMAP USB2 PHY Required properties: - compatible: Should be "ti,omap-usb2" + Should be "ti,dra7x-usb2" for the 1st instance of USB2 PHY on + DRA7x Should be "ti,dra7x-usb2-phy2" for the 2nd instance of USB2 PHY in DRA7x - reg : Address and length of the register set for the device. diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index 69617220c5d6..1685821eea41 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -23,6 +23,7 @@ Required properties: "allwinner,sun8i-h3-pinctrl" "allwinner,sun8i-h3-r-pinctrl" "allwinner,sun50i-a64-pinctrl" + "nextthing,gr8-pinctrl" - reg: Should contain the register physical address and length for the pin controller. diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt new file mode 100644 index 000000000000..5e60ad18f147 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt @@ -0,0 +1,65 @@ +Aspeed Pin Controllers +---------------------- + +The Aspeed SoCs vary in functionality inside a generation but have a common mux +device register layout. + +Required properties: +- compatible : Should be any one of the following: + "aspeed,ast2400-pinctrl" + "aspeed,g4-pinctrl" + "aspeed,ast2500-pinctrl" + "aspeed,g5-pinctrl" + +The pin controller node should be a child of a syscon node with the required +property: +- compatible: "syscon", "simple-mfd" + +Refer to the the bindings described in +Documentation/devicetree/bindings/mfd/syscon.txt + +Subnode Format +-------------- + +The required properties of child nodes are (as defined in pinctrl-bindings): +- function +- groups + +Each function has only one associated pin group. Each group is named by its +function. The following values for the function and groups properties are +supported: + +aspeed,ast2400-pinctrl, aspeed,g4-pinctrl: + +ACPI BMCINT DDCCLK DDCDAT FLACK FLBUSY FLWP GPID0 GPIE0 GPIE2 GPIE4 GPIE6 I2C10 +I2C11 I2C12 I2C13 I2C3 I2C4 I2C5 I2C6 I2C7 I2C8 I2C9 LPCPD LPCPME LPCSMI MDIO1 +MDIO2 NCTS1 NCTS3 NCTS4 NDCD1 NDCD3 NDCD4 NDSR1 NDSR3 NDTR1 NDTR3 NRI1 NRI3 +NRI4 NRTS1 NRTS3 PWM0 PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 RGMII1 RMII1 ROM16 +ROM8 ROMCS1 ROMCS2 ROMCS3 ROMCS4 RXD1 RXD3 RXD4 SD1 SGPMI SIOPBI SIOPBO TIMER3 +TIMER5 TIMER6 TIMER7 TIMER8 TXD1 TXD3 TXD4 UART6 VGAHS VGAVS VPI18 VPI24 VPI30 +VPO12 VPO24 + +aspeed,ast2500-pinctrl, aspeed,g5-pinctrl: + +GPID0 GPID2 GPIE0 I2C10 I2C11 I2C12 I2C13 I2C14 I2C3 I2C4 I2C5 I2C6 I2C7 I2C8 +I2C9 MAC1LINK MDIO1 MDIO2 OSCCLK PEWAKE PWM0 PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 +RGMII1 RGMII2 RMII1 RMII2 SD1 SPI1 TIMER4 TIMER5 TIMER6 TIMER7 TIMER8 + +Examples: + +syscon: scu@1e6e2000 { + compatible = "syscon", "simple-mfd"; + reg = <0x1e6e2000 0x1a8>; + + pinctrl: pinctrl { + compatible = "aspeed,g4-pinctrl"; + + pinctrl_i2c3_default: i2c3_default { + function = "I2C3"; + groups = "I2C3"; + }; + }; +}; + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices. diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt index 26bcb18f4e60..013c675b5b64 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt @@ -30,8 +30,7 @@ Second type has a dedicated interrupt per gpio bank. Pin controller node: Required properties: -- compatible : should be "st,<SOC>-<pio-block>-pinctrl" - like st,stih415-sbc-pinctrl, st,stih415-front-pinctrl and so on. +- compatible : should be "st,stih407-<pio-block>-pinctrl" - st,syscfg : Should be a phandle of the syscfg node. - st,retime-pin-mask : Should be mask to specify which pins can be retimed. If the property is not present, it is assumed that all the pins in the @@ -50,7 +49,11 @@ Optional properties: GPIO controller/bank node. Required properties: - gpio-controller : Indicates this device is a GPIO controller -- #gpio-cells : Should be one. The first cell is the pin number. +- #gpio-cells : Must be two. + - First cell: specifies the pin number inside the controller + - Second cell: specifies whether the pin is logically inverted. + - 0 = active high + - 1 = active low - st,bank-name : Should be a name string for this bank as specified in datasheet. @@ -76,23 +79,23 @@ include/dt-bindings/interrupt-controller/irq.h Example: pin-controller-sbc { - #address-cells = <1>; - #size-cells = <1>; - compatible = "st,stih415-sbc-pinctrl"; - st,syscfg = <&syscfg_sbc>; - reg = <0xfe61f080 0x4>; - reg-names = "irqmux"; - interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "irqmux"; - ranges = <0 0xfe610000 0x5000>; - - PIO0: gpio@fe610000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,stih407-sbc-pinctrl"; + st,syscfg = <&syscfg_sbc>; + reg = <0x0961f080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 188 IRQ_TYPE_NONE>; + interrupt-names = "irqmux"; + ranges = <0 0x09610000 0x6000>; + + pio0: gpio@09610000 { gpio-controller; - #gpio-cells = <1>; + #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; - reg = <0 0x100>; - st,bank-name = "PIO0"; + reg = <0x0 0x100>; + st,bank-name = "PIO0"; }; ... pin-functions nodes follow... @@ -162,7 +165,7 @@ pin-controller { sdhci0:sdhci@fe810000{ ... - interrupt-parent = <&PIO3>; + interrupt-parent = <&pio3>; #interrupt-cells = <2>; interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; /* Interrupt line via PIO3-3 */ interrupt-names = "card-detect"; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt index a54c39ebbf8b..8d893a874634 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt @@ -17,6 +17,9 @@ PMIC's from Qualcomm. "qcom,pm8994-gpio" "qcom,pma8084-gpio" + And must contain either "qcom,spmi-gpio" or "qcom,ssbi-gpio" + if the device is on an spmi bus or an ssbi bus respectively + - reg: Usage: required Value type: <prop-encoded-array> @@ -183,7 +186,7 @@ to specify in a pin configuration subnode: Example: pm8921_gpio: gpio@150 { - compatible = "qcom,pm8921-gpio"; + compatible = "qcom,pm8921-gpio", "qcom,ssbi-gpio"; reg = <0x150 0x160>; interrupts = <192 1>, <193 1>, <194 1>, <195 1>, <196 1>, <197 1>, diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt index b484ba1af78c..2ab95bc26066 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt @@ -19,6 +19,9 @@ of PMIC's from Qualcomm. "qcom,pm8994-mpp", "qcom,pma8084-mpp", + And must contain either "qcom,spmi-mpp" or "qcom,ssbi-mpp" + if the device is on an spmi bus or an ssbi bus respectively. + - reg: Usage: required Value type: <prop-encoded-array> @@ -158,7 +161,7 @@ to specify in a pin configuration subnode: Example: mpps@a000 { - compatible = "qcom,pm8841-mpp"; + compatible = "qcom,pm8841-mpp", "qcom,spmi-mpp"; reg = <0xa000>; gpio-controller; #gpio-cells = <2>; diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt index e4cf022c992e..13df9498311a 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -17,9 +17,11 @@ Required Properties: - "renesas,pfc-r8a7779": for R8A7779 (R-Car H1) compatible pin-controller. - "renesas,pfc-r8a7790": for R8A7790 (R-Car H2) compatible pin-controller. - "renesas,pfc-r8a7791": for R8A7791 (R-Car M2-W) compatible pin-controller. + - "renesas,pfc-r8a7792": for R8A7792 (R-Car V2H) compatible pin-controller. - "renesas,pfc-r8a7793": for R8A7793 (R-Car M2-N) compatible pin-controller. - "renesas,pfc-r8a7794": for R8A7794 (R-Car E2) compatible pin-controller. - "renesas,pfc-r8a7795": for R8A7795 (R-Car H3) compatible pin-controller. + - "renesas,pfc-r8a7796": for R8A7796 (R-Car M3-W) compatible pin-controller. - "renesas,pfc-sh73a0": for SH73A0 (SH-Mobile AG5) compatible pin-controller. - reg: Base address and length of each memory resource used by the pin diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt index 587bffb9cbc6..f9753c416974 100644 --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt @@ -14,6 +14,11 @@ Required properies: - #size-cells : The value of this property must be 1 - ranges : defines mapping between pin controller node (parent) to gpio-bank node (children). + - interrupt-parent: phandle of the interrupt parent to which the external + GPIO interrupts are forwarded to. + - st,syscfg: Should be phandle/offset pair. The phandle to the syscon node + which includes IRQ mux selection register, and the offset of the IRQ mux + selection register. - pins-are-numbered: Specify the subnodes are using numbered pinmux to specify pins. diff --git a/Documentation/devicetree/bindings/regulator/ltc3676.txt b/Documentation/devicetree/bindings/regulator/ltc3676.txt new file mode 100644 index 000000000000..d4eb366ce18c --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/ltc3676.txt @@ -0,0 +1,94 @@ +Linear Technology LTC3676 8-output regulators + +Required properties: +- compatible: "lltc,ltc3676" +- reg: I2C slave address + +Required child node: +- regulators: Contains eight regulator child nodes sw1, sw2, sw3, sw4, + ldo1, ldo2, ldo3, and ldo4, specifying the initialization data as + documented in Documentation/devicetree/bindings/regulator/regulator.txt. + +Each regulator is defined using the standard binding for regulators. The +nodes for sw1, sw2, sw3, sw4, ldo1, ldo2 and ldo4 additionally need to specify +the resistor values of their external feedback voltage dividers: + +Required properties (not on ldo3): +- lltc,fb-voltage-divider: An array of two integers containing the resistor + values R1 and R2 of the feedback voltage divider in ohms. + +Regulators sw1, sw2, sw3, sw4 can regulate the feedback reference from: +412.5mV to 800mV in 12.5 mV steps. The output voltage thus ranges between +0.4125 * (1 + R1/R2) V and 0.8 * (1 + R1/R2) V. + +Regulators ldo1, ldo2, and ldo4 have a fixed 0.725 V reference and thus output +0.725 * (1 + R1/R2) V. The ldo3 regulator is fixed to 1.8 V. The ldo1 standby +regulator can not be disabled and thus should have the regulator-always-on +property set. + +Example: + + ltc3676: pmic@3c { + compatible = "lltc,ltc3676"; + reg = <0x3c>; + + regulators { + sw1_reg: sw1 { + regulator-min-microvolt = <674400>; + regulator-max-microvolt = <1308000>; + lltc,fb-voltage-divider = <127000 200000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <1033310>; + regulator-max-microvolt = <200400>; + lltc,fb-voltage-divider = <301000 200000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3_reg: sw3 { + regulator-min-microvolt = <674400>; + regulator-max-microvolt = <130800>; + lltc,fb-voltage-divider = <127000 200000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-min-microvolt = <868310>; + regulator-max-microvolt = <168400>; + lltc,fb-voltage-divider = <221000 200000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: ldo2 { + regulator-min-microvolt = <2490375>; + regulator-max-microvolt = <2490375>; + lltc,fb-voltage-divider = <487000 200000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: ldo3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + }; + + ldo4_reg: ldo4 { + regulator-min-microvolt = <3023250>; + regulator-max-microvolt = <3023250>; + lltc,fb-voltage-divider = <634000 200000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/pv88080.txt b/Documentation/devicetree/bindings/regulator/pv88080.txt index 38a614210dcb..e6e4b9c82d89 100644 --- a/Documentation/devicetree/bindings/regulator/pv88080.txt +++ b/Documentation/devicetree/bindings/regulator/pv88080.txt @@ -1,22 +1,28 @@ * Powerventure Semiconductor PV88080 Voltage Regulator Required properties: -- compatible: "pvs,pv88080". -- reg: I2C slave address, usually 0x49. +- compatible: Must be one of the following, depending on the + silicon version: + - "pvs,pv88080" (DEPRECATED) + + - "pvs,pv88080-aa" for PV88080 AA or AB silicon + - "pvs,pv88080-ba" for PV88080 BA or BB silicon + NOTE: The use of the compatibles with no silicon version is deprecated. +- reg: I2C slave address, usually 0x49 - interrupts: the interrupt outputs of the controller - regulators: A node that houses a sub-node for each regulator within the device. Each sub-node is identified using the node's name, with valid values listed below. The content of each sub-node is defined by the standard binding for regulators; see regulator.txt. - BUCK1, BUCK2, and BUCK3. + BUCK1, BUCK2, BUCK3 and HVBUCK. Optional properties: - Any optional property defined in regulator.txt -Example +Example: pmic: pv88080@49 { - compatible = "pvs,pv88080"; + compatible = "pvs,pv88080-ba"; reg = <0x49>; interrupt-parent = <&gpio>; interrupts = <24 24>; @@ -45,5 +51,12 @@ Example regulator-min-microamp = <1496000>; regulator-max-microamp = <4189000>; }; + + HVBUCK { + regulator-name = "hvbuck"; + regulator-min-microvolt = < 5000>; + regulator-max-microvolt = <1275000>; + }; }; }; + diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index ecfc593cac15..6ab5aef619d9 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -13,7 +13,7 @@ Optional properties: - regulator-allow-bypass: allow the regulator to go into bypass mode - regulator-allow-set-load: allow the regulator performance level to be configured - <name>-supply: phandle to the parent supply/regulator node -- regulator-ramp-delay: ramp delay for regulator(in uV/uS) +- regulator-ramp-delay: ramp delay for regulator(in uV/us) For hardware which supports disabling ramp rate, it should be explicitly initialised to zero (regulator-ramp-delay = <0>) for disabling ramp delay. - regulator-enable-ramp-delay: The time taken, in microseconds, for the supply diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt index f5561ac7e17e..f86bb06c39e9 100644 --- a/Documentation/devicetree/bindings/serial/8250.txt +++ b/Documentation/devicetree/bindings/serial/8250.txt @@ -42,9 +42,8 @@ Optional properties: - auto-flow-control: one way to enable automatic flow control support. The driver is allowed to detect support for the capability even without this property. -- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD - line respectively. It will use specified GPIO instead of the peripheral - function pin for the UART feature. If unsure, don't specify this property. +- tx-threshold: Specify the TX FIFO low water indication for parts with + programmable TX FIFO thresholds. Note: * fsl,ns16550: @@ -66,19 +65,3 @@ Example: interrupts = <10>; reg-shift = <2>; }; - -Example for OMAP UART using GPIO-based modem control signals: - - uart4: serial@49042000 { - compatible = "ti,omap3-uart"; - reg = <0x49042000 0x400>; - interrupts = <80>; - ti,hwmods = "uart4"; - clock-frequency = <48000000>; - cts-gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; - rts-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>; - dtr-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; - dsr-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; - dcd-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; - rng-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; - }; diff --git a/Documentation/devicetree/bindings/serial/st,stm32-usart.txt b/Documentation/devicetree/bindings/serial/st,stm32-usart.txt new file mode 100644 index 000000000000..85ec5f2b1996 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/st,stm32-usart.txt @@ -0,0 +1,46 @@ +* STMicroelectronics STM32 USART + +Required properties: +- compatible: Can be either "st,stm32-usart", "st,stm32-uart", +"st,stm32f7-usart" or "st,stm32f7-uart" depending on whether +the device supports synchronous mode and is compatible with +stm32(f4) or stm32f7. +- reg: The address and length of the peripheral registers space +- interrupts: The interrupt line of the USART instance +- clocks: The input clock of the USART instance + +Optional properties: +- pinctrl: The reference on the pins configuration +- st,hw-flow-ctrl: bool flag to enable hardware flow control. +- dmas: phandle(s) to DMA controller node(s). Refer to stm32-dma.txt +- dma-names: "rx" and/or "tx" + +Examples: +usart4: serial@40004c00 { + compatible = "st,stm32-uart"; + reg = <0x40004c00 0x400>; + interrupts = <52>; + clocks = <&clk_pclk1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart4>; +}; + +usart2: serial@40004400 { + compatible = "st,stm32-usart", "st,stm32-uart"; + reg = <0x40004400 0x400>; + interrupts = <38>; + clocks = <&clk_pclk1>; + st,hw-flow-ctrl; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart2 &pinctrl_usart2_rtscts>; +}; + +usart1: serial@40011000 { + compatible = "st,stm32-usart", "st,stm32-uart"; + reg = <0x40011000 0x400>; + interrupts = <37>; + clocks = <&rcc 0 164>; + dmas = <&dma2 2 4 0x414 0x0>, + <&dma2 7 4 0x414 0x0>; + dma-names = "rx", "tx"; +}; diff --git a/Documentation/devicetree/bindings/soc/mediatek/auxadc.txt b/Documentation/devicetree/bindings/soc/mediatek/auxadc.txt deleted file mode 100644 index bdb782918a72..000000000000 --- a/Documentation/devicetree/bindings/soc/mediatek/auxadc.txt +++ /dev/null @@ -1,21 +0,0 @@ -MediaTek AUXADC -=============== - -The Auxiliary Analog/Digital Converter (AUXADC) is an ADC found -in some Mediatek SoCs which among other things measures the temperatures -in the SoC. It can be used directly with register accesses, but it is also -used by thermal controller which reads the temperatures from the AUXADC -directly via its own bus interface. See -Documentation/devicetree/bindings/thermal/mediatek-thermal.txt -for the Thermal Controller which holds a phandle to the AUXADC. - -Required properties: -- compatible: Must be "mediatek,mt8173-auxadc" -- reg: Address range of the AUXADC unit - -Example: - -auxadc: auxadc@11001000 { - compatible = "mediatek,mt8173-auxadc"; - reg = <0 0x11001000 0 0x1000>; -}; diff --git a/Documentation/devicetree/bindings/sound/nau8810.txt b/Documentation/devicetree/bindings/sound/nau8810.txt new file mode 100644 index 000000000000..05830e477acd --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nau8810.txt @@ -0,0 +1,16 @@ +NAU8810 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "nuvoton,nau8810" + + - reg : the I2C address of the device. + +Example: + +codec: nau8810@1a { + compatible = "nuvoton,nau8810"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-sgtl5000.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-sgtl5000.txt new file mode 100644 index 000000000000..5da7da4ea07a --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-sgtl5000.txt @@ -0,0 +1,42 @@ +NVIDIA Tegra audio complex, with SGTL5000 CODEC + +Required properties: +- compatible : "nvidia,tegra-audio-sgtl5000" +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names : Must include the following entries: + - pll_a + - pll_a_out0 + - mclk (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) +- nvidia,model : The user-visible name of this sound complex. +- nvidia,audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names for sources and + sinks are the SGTL5000's pins (as documented in its binding), and the jacks + on the board: + + * Headphone Jack + * Line In Jack + * Mic Jack + +- nvidia,i2s-controller : The phandle of the Tegra I2S controller that's + connected to the CODEC. +- nvidia,audio-codec : The phandle of the SGTL5000 audio codec. + +Example: + +sound { + compatible = "toradex,tegra-audio-sgtl5000-apalis_t30", + "nvidia,tegra-audio-sgtl5000"; + nvidia,model = "Toradex Apalis T30"; + nvidia,audio-routing = + "Headphone Jack", "HP_OUT", + "LINE_IN", "Line In Jack", + "MIC_IN", "Mic Jack"; + nvidia,i2s-controller = <&tegra_i2s2>; + nvidia,audio-codec = <&sgtl5000>; + clocks = <&tegra_car TEGRA30_CLK_PLL_A>, + <&tegra_car TEGRA30_CLK_PLL_A_OUT0>, + <&tegra_car TEGRA30_CLK_EXTERN1>; + clock-names = "pll_a", "pll_a_out0", "mclk"; +}; diff --git a/Documentation/devicetree/bindings/sound/omap-mcpdm.txt b/Documentation/devicetree/bindings/sound/omap-mcpdm.txt index 6f6c2f8e908d..0741dff048dd 100644 --- a/Documentation/devicetree/bindings/sound/omap-mcpdm.txt +++ b/Documentation/devicetree/bindings/sound/omap-mcpdm.txt @@ -8,8 +8,6 @@ Required properties: - interrupts: Interrupt number for McPDM - interrupt-parent: The parent interrupt controller - ti,hwmods: Name of the hwmod associated to the McPDM -- clocks: phandle for the pdmclk provider, likely <&twl6040> -- clock-names: Must be "pdmclk" Example: @@ -21,11 +19,3 @@ mcpdm: mcpdm@40132000 { interrupt-parent = <&gic>; ti,hwmods = "mcpdm"; }; - -In board DTS file the pdmclk needs to be added: - -&mcpdm { - clocks = <&twl6040>; - clock-names = "pdmclk"; - status = "okay"; -}; diff --git a/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt b/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt index 48129368d4d9..d9d8635ff94c 100644 --- a/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt +++ b/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt @@ -16,6 +16,24 @@ Required properties: * "spkr-iomux" - qcom,model : Name of the sound card. +- qcom,audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source. Valid names could be power supplies, MicBias + of msm8x16_wcd codec and the jacks on the board: + + Power supplies: + * MIC BIAS External1 + * MIC BIAS External2 + * MIC BIAS Internal1 + * MIC BIAS Internal2 + + Board connectors: + * Headset Mic + * Secondary Mic", + * DMIC + * Ext Spk + Dai-link subnode properties and subnodes: Required dai-link subnodes: @@ -37,6 +55,18 @@ sound: sound { reg-names = "mic-iomux", "spkr-iomux"; qcom,model = "DB410c"; + qcom,audio-routing = + "MIC BIAS External1", "Handset Mic", + "MIC BIAS Internal2", "Headset Mic", + "MIC BIAS External1", "Secondary Mic", + "AMIC1", "MIC BIAS External1", + "AMIC2", "MIC BIAS Internal2", + "AMIC3", "MIC BIAS External1", + "DMIC1", "MIC BIAS Internal1", + "MIC BIAS Internal1", "Digital Mic1", + "DMIC2", "MIC BIAS Internal1", + "MIC BIAS Internal1", "Digital Mic2"; + /* I2S - Internal codec */ internal-dai-link@0 { cpu { /* PRIMARY */ diff --git a/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt b/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt deleted file mode 100644 index 255ece3043ad..000000000000 --- a/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt +++ /dev/null @@ -1,75 +0,0 @@ -Renesas Sampling Rate Convert Sound Card: - -Renesas Sampling Rate Convert Sound Card specifies audio DAI connections of SoC <-> codec. - -Required properties: - -- compatible : "renesas,rsrc-card{,<board>}" - Examples with boards are: - - "renesas,rsrc-card" - - "renesas,rsrc-card,lager" - - "renesas,rsrc-card,koelsch" -Optional properties: - -- card_name : User specified audio sound card name, one string - property. -- cpu : CPU sub-node -- codec : CODEC sub-node - -Optional subnode properties: - -- format : CPU/CODEC common audio format. - "i2s", "right_j", "left_j" , "dsp_a" - "dsp_b", "ac97", "pdm", "msb", "lsb" -- frame-master : Indicates dai-link frame master. - phandle to a cpu or codec subnode. -- bitclock-master : Indicates dai-link bit clock master. - phandle to a cpu or codec subnode. -- bitclock-inversion : bool property. Add this if the - dai-link uses bit clock inversion. -- frame-inversion : bool property. Add this if the - dai-link uses frame clock inversion. -- convert-rate : platform specified sampling rate convert -- convert-channels : platform specified converted channel size (2 - 8 ch) -- audio-prefix : see audio-routing -- audio-routing : A list of the connections between audio components. - Each entry is a pair of strings, the first being the connection's sink, - the second being the connection's source. Valid names for sources. - use audio-prefix if some components is using same sink/sources naming. - it can be used if compatible was "renesas,rsrc-card"; - -Required CPU/CODEC subnodes properties: - -- sound-dai : phandle and port of CPU/CODEC - -Optional CPU/CODEC subnodes properties: - -- clocks / system-clock-frequency : specify subnode's clock if needed. - it can be specified via "clocks" if system has - clock node (= common clock), or "system-clock-frequency" - (if system doens't support common clock) - If a clock is specified, it is - enabled with clk_prepare_enable() - in dai startup() and disabled with - clk_disable_unprepare() in dai - shutdown(). - -Example - -sound { - compatible = "renesas,rsrc-card,lager"; - - card-name = "rsnd-ak4643"; - format = "left_j"; - bitclock-master = <&sndcodec>; - frame-master = <&sndcodec>; - - sndcpu: cpu { - sound-dai = <&rcar_sound>; - }; - - sndcodec: codec { - sound-dai = <&ak4643>; - system-clock-frequency = <11289600>; - }; -}; diff --git a/Documentation/devicetree/bindings/sound/rockchip,rk3399-gru-sound.txt b/Documentation/devicetree/bindings/sound/rockchip,rk3399-gru-sound.txt new file mode 100644 index 000000000000..eac91db07178 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rockchip,rk3399-gru-sound.txt @@ -0,0 +1,22 @@ +ROCKCHIP with MAX98357A/RT5514/DA7219 codecs on GRU boards + +Required properties: +- compatible: "rockchip,rk3399-gru-sound" +- rockchip,cpu: The phandle of the Rockchip I2S controller that's + connected to the codecs +- rockchip,codec: The phandle of the MAX98357A/RT5514/DA7219 codecs + +Optional properties: +- dmic-wakeup-delay-ms : specify delay time (ms) for DMIC ready. + If this option is specified, which means it's required dmic need + delay for DMIC to ready so that rt5514 can avoid recording before + DMIC send valid data + +Example: + +sound { + compatible = "rockchip,rk3399-gru-sound"; + rockchip,cpu = <&i2s0>; + rockchip,codec = <&max98357a &rt5514 &da7219>; + dmic-wakeup-delay-ms = <20>; +}; diff --git a/Documentation/devicetree/bindings/sound/rt5659.txt b/Documentation/devicetree/bindings/sound/rt5659.txt index 5f79e7fde032..1766e0543fc5 100644 --- a/Documentation/devicetree/bindings/sound/rt5659.txt +++ b/Documentation/devicetree/bindings/sound/rt5659.txt @@ -12,6 +12,9 @@ Required properties: Optional properties: +- clocks: The phandle of the master clock to the CODEC +- clock-names: Should be "mclk" + - realtek,in1-differential - realtek,in3-differential - realtek,in4-differential diff --git a/Documentation/devicetree/bindings/sound/rt5660.txt b/Documentation/devicetree/bindings/sound/rt5660.txt new file mode 100644 index 000000000000..30be5f921930 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5660.txt @@ -0,0 +1,47 @@ +RT5660 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : "realtek,rt5660". + +- reg : The I2C address of the device. + +Optional properties: + +- clocks: The phandle of the master clock to the CODEC +- clock-names: Should be "mclk" + +- realtek,in1-differential +- realtek,in3-differential + Boolean. Indicate MIC1/3 input are differential, rather than single-ended. + +- realtek,poweroff-in-suspend + Boolean. If the codec will be powered off in suspend, the resume should be + added delay time for waiting codec power ready. + +- realtek,dmic1-data-pin + 0: dmic1 is not used + 1: using GPIO2 pin as dmic1 data pin + 2: using IN1P pin as dmic1 data pin + +Pins on the device (for linking into audio routes) for RT5660: + + * DMIC L1 + * DMIC R1 + * IN1P + * IN1N + * IN2P + * IN3P + * IN3N + * SPO + * LOUTL + * LOUTR + +Example: + +rt5660 { + compatible = "realtek,rt5660"; + reg = <0x1c>; +}; diff --git a/Documentation/devicetree/bindings/sound/rt5663.txt b/Documentation/devicetree/bindings/sound/rt5663.txt new file mode 100644 index 000000000000..7d3c974c6e2e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5663.txt @@ -0,0 +1,30 @@ +RT5663/RT5668 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : One of "realtek,rt5663" or "realtek,rt5668". + +- reg : The I2C address of the device. + +- interrupts : The CODEC's interrupt output. + +Optional properties: + +Pins on the device (for linking into audio routes) for RT5663/RT5668: + + * IN1P + * IN1N + * IN2P + * IN2N + * HPOL + * HPOR + +Example: + +codec: rt5663@12 { + compatible = "realtek,rt5663"; + reg = <0x12>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; +}; diff --git a/Documentation/devicetree/bindings/sound/simple-card.txt b/Documentation/devicetree/bindings/sound/simple-card.txt index 59d862801e59..c7a93931fad2 100644 --- a/Documentation/devicetree/bindings/sound/simple-card.txt +++ b/Documentation/devicetree/bindings/sound/simple-card.txt @@ -22,6 +22,8 @@ Optional properties: headphones are attached. - simple-audio-card,mic-det-gpio : Reference to GPIO that signals when a microphone is attached. +- simple-audio-card,aux-devs : List of phandles pointing to auxiliary devices, such + as amplifiers, to be added to the sound card. Optional subnodes: @@ -162,3 +164,38 @@ sound { }; }; }; + +Example 3 - route audio from IMX6 SSI2 through TLV320DAC3100 codec +through TPA6130A2 amplifier to headphones: + +&i2c0 { + codec: tlv320dac3100@18 { + compatible = "ti,tlv320dac3100"; + ... + } + + amp: tpa6130a2@60 { + compatible = "ti,tpa6130a2"; + ... + } +} + +sound { + compatible = "simple-audio-card"; + ... + simple-audio-card,widgets = + "Headphone", "Headphone Jack"; + simple-audio-card,routing = + "Headphone Jack", "HPLEFT", + "Headphone Jack", "HPRIGHT", + "LEFTIN", "HPL", + "RIGHTIN", "HPR"; + simple-audio-card,aux-devs = <&>; + simple-audio-card,cpu { + sound-dai = <&ssi2>; + }; + simple-audio-card,codec { + sound-dai = <&codec>; + clocks = ... + }; +}; diff --git a/Documentation/devicetree/bindings/sound/simple-scu-card.txt b/Documentation/devicetree/bindings/sound/simple-scu-card.txt new file mode 100644 index 000000000000..d6fe47ed09af --- /dev/null +++ b/Documentation/devicetree/bindings/sound/simple-scu-card.txt @@ -0,0 +1,110 @@ +ASoC simple SCU Sound Card + +Simple-Card specifies audio DAI connections of SoC <-> codec. + +Required properties: + +- compatible : "simple-scu-audio-card" + "renesas,rsrc-card" + +Optional properties: + +- simple-audio-card,name : User specified audio sound card name, one string + property. +- simple-audio-card,cpu : CPU sub-node +- simple-audio-card,codec : CODEC sub-node + +Optional subnode properties: + +- simple-audio-card,format : CPU/CODEC common audio format. + "i2s", "right_j", "left_j" , "dsp_a" + "dsp_b", "ac97", "pdm", "msb", "lsb" +- simple-audio-card,frame-master : Indicates dai-link frame master. + phandle to a cpu or codec subnode. +- simple-audio-card,bitclock-master : Indicates dai-link bit clock master. + phandle to a cpu or codec subnode. +- simple-audio-card,bitclock-inversion : bool property. Add this if the + dai-link uses bit clock inversion. +- simple-audio-card,frame-inversion : bool property. Add this if the + dai-link uses frame clock inversion. +- simple-audio-card,convert-rate : platform specified sampling rate convert +- simple-audio-card,convert-channels : platform specified converted channel size (2 - 8 ch) +- simple-audio-card,prefix : see audio-routing +- simple-audio-card,routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names for sources. + use audio-prefix if some components is using same sink/sources naming. + it can be used if compatible was "renesas,rsrc-card"; + +Required CPU/CODEC subnodes properties: + +- sound-dai : phandle and port of CPU/CODEC + +Optional CPU/CODEC subnodes properties: + +- clocks / system-clock-frequency : specify subnode's clock if needed. + it can be specified via "clocks" if system has + clock node (= common clock), or "system-clock-frequency" + (if system doens't support common clock) + If a clock is specified, it is + enabled with clk_prepare_enable() + in dai startup() and disabled with + clk_disable_unprepare() in dai + shutdown(). + +Example 1. Sampling Rate Covert + +sound { + compatible = "simple-scu-audio-card"; + + simple-audio-card,name = "rsnd-ak4643"; + simple-audio-card,format = "left_j"; + simple-audio-card,format = "left_j"; + simple-audio-card,bitclock-master = <&sndcodec>; + simple-audio-card,frame-master = <&sndcodec>; + + simple-audio-card,convert-rate = <48000>; /* see audio_clk_a */ + + simple-audio-card,prefix = "ak4642"; + simple-audio-card,routing = "ak4642 Playback", "DAI0 Playback", + "DAI0 Capture", "ak4642 Capture"; + + sndcpu: simple-audio-card,cpu { + sound-dai = <&rcar_sound>; + }; + + sndcodec: simple-audio-card,codec { + sound-dai = <&ak4643>; + system-clock-frequency = <11289600>; + }; +}; + +Example 2. 2 CPU 1 Codec + +sound { + compatible = "renesas,rsrc-card"; + + card-name = "rsnd-ak4643"; + format = "left_j"; + bitclock-master = <&dpcmcpu>; + frame-master = <&dpcmcpu>; + + convert-rate = <48000>; /* see audio_clk_a */ + + audio-prefix = "ak4642"; + audio-routing = "ak4642 Playback", "DAI0 Playback", + "ak4642 Playback", "DAI1 Playback"; + + dpcmcpu: cpu@0 { + sound-dai = <&rcar_sound 0>; + }; + + cpu@1 { + sound-dai = <&rcar_sound 1>; + }; + + codec { + sound-dai = <&ak4643>; + clocks = <&audio_clock>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt b/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt index 16bcdfb6760e..745dc62f76ea 100644 --- a/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt +++ b/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt @@ -11,7 +11,9 @@ Documentation/devicetree/bindings/sound/simple-card.txt. --------------------------------------- Required properties: - - compatible: "st,sti-uni-player" or "st,sti-uni-reader" + - compatible: "st,stih407-uni-player-hdmi", "st,stih407-uni-player-pcm-out", + "st,stih407-uni-player-dac", "st,stih407-uni-player-spdif", + "st,stih407-uni-reader-pcm_in", "st,stih407-uni-reader-hdmi", - st,syscfg: phandle to boot-device system configuration registers @@ -33,32 +35,24 @@ Required properties: "tx" for "st,sti-uni-player" compatibility "rx" for "st,sti-uni-reader" compatibility - - st,version: IP version integrated in SOC. - - - dai-name: DAI name that describes the IP. - - - st,mode: IP working mode depending on associated codec. - "HDMI" connected to HDMI codec and support IEC HDMI formats (player only). - "SPDIF" connected to SPDIF codec and support SPDIF formats (player only). - "PCM" PCM standard mode for I2S or TDM bus. - "TDM" TDM mode for TDM bus. - Required properties ("st,sti-uni-player" compatibility only): - clocks: CPU_DAI IP clock source, listed in the same order than the CPU_DAI properties. - - st,uniperiph-id: internal SOC IP instance ID. - Optional properties: - pinctrl-0: defined for CPU_DAI@1 and CPU_DAI@4 to describe I2S PIOs for external codecs connection. - pinctrl-names: should contain only one value - "default". + - st,tdm-mode: to declare to set TDM mode for unireader and uniplayer IPs. + Only compartible with IPs in charge of the external I2S/TDM bus. + Should be declared depending on associated codec. + Example: - sti_uni_player1: sti-uni-player@1 { - compatible = "st,sti-uni-player"; + sti_uni_player1: sti-uni-player@0x8D81000 { + compatible = "st,stih407-uni-player-hdmi"; status = "okay"; #sound-dai-cells = <0>; st,syscfg = <&syscfg_core>; @@ -66,15 +60,12 @@ Example: reg = <0x8D81000 0x158>; interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>; dmas = <&fdma0 3 0 1>; - st,dai-name = "Uni Player #1 (I2S)"; dma-names = "tx"; - st,uniperiph-id = <1>; - st,version = <5>; - st,mode = "TDM"; + st,tdm-mode = <1>; }; - sti_uni_player2: sti-uni-player@2 { - compatible = "st,sti-uni-player"; + sti_uni_player2: sti-uni-player@0x8D82000 { + compatible = "st,stih407-uni-player-pcm-out"; status = "okay"; #sound-dai-cells = <0>; st,syscfg = <&syscfg_core>; @@ -82,15 +73,11 @@ Example: reg = <0x8D82000 0x158>; interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>; dmas = <&fdma0 4 0 1>; - dai-name = "Uni Player #2 (DAC)"; dma-names = "tx"; - st,uniperiph-id = <2>; - st,version = <5>; - st,mode = "PCM"; }; - sti_uni_player3: sti-uni-player@3 { - compatible = "st,sti-uni-player"; + sti_uni_player3: sti-uni-player@0x8D85000 { + compatible = "st,stih407-uni-player-spdif"; status = "okay"; #sound-dai-cells = <0>; st,syscfg = <&syscfg_core>; @@ -99,14 +86,10 @@ Example: interrupts = <GIC_SPI 89 IRQ_TYPE_NONE>; dmas = <&fdma0 7 0 1>; dma-names = "tx"; - dai-name = "Uni Player #3 (SPDIF)"; - st,uniperiph-id = <3>; - st,version = <5>; - st,mode = "SPDIF"; }; - sti_uni_reader1: sti-uni-reader@1 { - compatible = "st,sti-uni-reader"; + sti_uni_reader1: sti-uni-reader@0x8D84000 { + compatible = "st,stih407-uni-reader-hdmi"; status = "disabled"; #sound-dai-cells = <0>; st,syscfg = <&syscfg_core>; @@ -114,9 +97,6 @@ Example: interrupts = <GIC_SPI 88 IRQ_TYPE_NONE>; dmas = <&fdma0 6 0 1>; dma-names = "rx"; - dai-name = "Uni Reader #1 (HDMI RX)"; - st,version = <3>; - st,mode = "PCM"; }; 2) sti-sas-codec: internal audio codec IPs driver diff --git a/Documentation/devicetree/bindings/sound/sunxi,sun4i-spdif.txt b/Documentation/devicetree/bindings/sound/sunxi,sun4i-spdif.txt index 13503aa505a9..0230c4d20506 100644 --- a/Documentation/devicetree/bindings/sound/sunxi,sun4i-spdif.txt +++ b/Documentation/devicetree/bindings/sound/sunxi,sun4i-spdif.txt @@ -9,6 +9,7 @@ Required properties: - compatible : should be one of the following: - "allwinner,sun4i-a10-spdif": for the Allwinner A10 SoC + - "allwinner,sun6i-a31-spdif": for the Allwinner A31 SoC - reg : Offset and length of the register set for the device. @@ -25,6 +26,8 @@ Required properties: "apb" clock for the spdif bus. "spdif" clock for spdif controller. + - resets : reset specifier for the ahb reset (A31 and newer only) + Example: spdif: spdif@01c21000 { diff --git a/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt b/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt index eff12be5e789..9340d2ddcc54 100644 --- a/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt +++ b/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt @@ -11,6 +11,7 @@ Required properties: "ti,tlv320aic3110" - TLV320AIC3110 (stereo speaker amp, no MiniDSP) "ti,tlv320aic3120" - TLV320AIC3120 (mono speaker amp, MiniDSP) "ti,tlv320aic3111" - TLV320AIC3111 (stereo speaker amp, MiniDSP) + "ti,tlv320dac3100" - TLV320DAC3100 (no ADC, mono speaker amp, no MiniDSP) - reg - <int> - I2C slave address - HPVDD-supply, SPRVDD-supply, SPLVDD-supply, AVDD-supply, IOVDD-supply, @@ -37,9 +38,11 @@ CODEC output pins: * MICBIAS CODEC input pins: - * MIC1LP - * MIC1RP - * MIC1LM + * MIC1LP, devices with ADC + * MIC1RP, devices with ADC + * MIC1LM, devices with ADC + * AIN1, devices without ADC + * AIN2, devices without ADC The pins can be used in referring sound node's audio-routing property. diff --git a/Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.txt b/Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.txt new file mode 100644 index 000000000000..ad7ac80a3841 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.txt @@ -0,0 +1,233 @@ +Broadcom SPI controller + +The Broadcom SPI controller is a SPI master found on various SOCs, including +BRCMSTB (BCM7XXX), Cygnus, NSP and NS2. The Broadcom Master SPI hw IP consits +of : + MSPI : SPI master controller can read and write to a SPI slave device + BSPI : Broadcom SPI in combination with the MSPI hw IP provides acceleration + for flash reads and be configured to do single, double, quad lane + io with 3-byte and 4-byte addressing support. + + Supported Broadcom SoCs have one instance of MSPI+BSPI controller IP. + MSPI master can be used wihout BSPI. BRCMSTB SoCs have an additional instance + of a MSPI master without the BSPI to use with non flash slave devices that + use SPI protocol. + +Required properties: + +- #address-cells: + Must be <1>, as required by generic SPI binding. + +- #size-cells: + Must be <0>, also as required by generic SPI binding. + +- compatible: + Must be one of : + "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-qspi" : MSPI+BSPI on BRCMSTB SoCs + "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-mspi" : Second Instance of MSPI + BRCMSTB SoCs + "brcm,spi-bcm-qspi", "brcm,spi-nsp-qspi" : MSPI+BSPI on Cygnus, NSP + "brcm,spi-bcm-qspi", "brcm,spi-ns2-qspi" : NS2 SoCs + +- reg: + Define the bases and ranges of the associated I/O address spaces. + The required range is MSPI controller registers. + +- reg-names: + First name does not matter, but must be reserved for the MSPI controller + register range as mentioned in 'reg' above, and will typically contain + - "bspi_regs": BSPI register range, not required with compatible + "spi-brcmstb-mspi" + - "mspi_regs": MSPI register range is required for compatible strings + - "intr_regs", "intr_status_reg" : Interrupt and status register for + NSP, NS2, Cygnus SoC + +- interrupts + The interrupts used by the MSPI and/or BSPI controller. + +- interrupt-names: + Names of interrupts associated with MSPI + - "mspi_halted" : + - "mspi_done": Indicates that the requested SPI operation is complete. + - "spi_lr_fullness_reached" : Linear read BSPI pipe full + - "spi_lr_session_aborted" : Linear read BSPI pipe aborted + - "spi_lr_impatient" : Linear read BSPI requested when pipe empty + - "spi_lr_session_done" : Linear read BSPI session done + +- clocks: + A phandle to the reference clock for this block. + +Optional properties: + + +- native-endian + Defined when using BE SoC and device uses BE register read/write + +Recommended optional m25p80 properties: +- spi-rx-bus-width: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Examples: + +BRCMSTB SoC Example: + + SPI Master (MSPI+BSPI) for SPI-NOR access: + + spi@f03e3400 { + #address-cells = <0x1>; + #size-cells = <0x0>; + compatible = "brcm,spi-brcmstb-qspi", "brcm,spi-brcmstb-qspi"; + reg = <0xf03e0920 0x4 0xf03e3400 0x188 0xf03e3200 0x50>; + reg-names = "cs_reg", "mspi", "bspi"; + interrupts = <0x6 0x5 0x4 0x3 0x2 0x1 0x0>; + interrupt-parent = <0x1c>; + interrupt-names = "mspi_halted", + "mspi_done", + "spi_lr_overread", + "spi_lr_session_done", + "spi_lr_impatient", + "spi_lr_session_aborted", + "spi_lr_fullness_reached"; + + clocks = <&hif_spi>; + clock-names = "sw_spi"; + + m25p80@0 { + #size-cells = <0x2>; + #address-cells = <0x2>; + compatible = "m25p80"; + reg = <0x0>; + spi-max-frequency = <0x2625a00>; + spi-cpol; + spi-cpha; + m25p,fast-read; + + flash0.bolt@0 { + reg = <0x0 0x0 0x0 0x100000>; + }; + + flash0.macadr@100000 { + reg = <0x0 0x100000 0x0 0x10000>; + }; + + flash0.nvram@110000 { + reg = <0x0 0x110000 0x0 0x10000>; + }; + + flash0.kernel@120000 { + reg = <0x0 0x120000 0x0 0x400000>; + }; + + flash0.devtree@520000 { + reg = <0x0 0x520000 0x0 0x10000>; + }; + + flash0.splash@530000 { + reg = <0x0 0x530000 0x0 0x80000>; + }; + + flash0@0 { + reg = <0x0 0x0 0x0 0x4000000>; + }; + }; + }; + + + MSPI master for any SPI device : + + spi@f0416000 { + #address-cells = <1>; + #size-cells = <0>; + clocks = <&upg_fixed>; + compatible = "brcm,spi-brcmstb-qspi", "brcm,spi-brcmstb-mspi"; + reg = <0xf0416000 0x180>; + reg-names = "mspi"; + interrupts = <0x14>; + interrupt-parent = <&irq0_aon_intc>; + interrupt-names = "mspi_done"; + }; + +iProc SoC Example: + + qspi: spi@18027200 { + compatible = "brcm,spi-bcm-qspi", "brcm,spi-nsp-qspi"; + reg = <0x18027200 0x184>, + <0x18027000 0x124>, + <0x1811c408 0x004>, + <0x180273a0 0x01c>; + reg-names = "mspi_regs", "bspi_regs", "intr_regs", "intr_status_reg"; + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = + "spi_lr_fullness_reached", + "spi_lr_session_aborted", + "spi_lr_impatient", + "spi_lr_session_done", + "mspi_done", + "mspi_halted"; + clocks = <&iprocmed>; + clock-names = "iprocmed"; + num-cs = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + + NS2 SoC Example: + + qspi: spi@66470200 { + compatible = "brcm,spi-bcm-qspi", "brcm,spi-ns2-qspi"; + reg = <0x66470200 0x184>, + <0x66470000 0x124>, + <0x67017408 0x004>, + <0x664703a0 0x01c>; + reg-names = "mspi", "bspi", "intr_regs", + "intr_status_reg"; + interrupts = <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "spi_l1_intr"; + clocks = <&iprocmed>; + clock-names = "iprocmed"; + num-cs = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + + m25p80 node for NSP, NS2 + + &qspi { + flash: m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "m25p80"; + reg = <0x0>; + spi-max-frequency = <12500000>; + m25p,fast-read; + spi-cpol; + spi-cpha; + + partition@0 { + label = "boot"; + reg = <0x00000000 0x000a0000>; + }; + + partition@a0000 { + label = "env"; + reg = <0x000a0000 0x00060000>; + }; + + partition@100000 { + label = "system"; + reg = <0x00100000 0x00600000>; + }; + + partition@700000 { + label = "rootfs"; + reg = <0x00700000 0x01900000>; + }; + }; diff --git a/Documentation/devicetree/bindings/spi/jcore,spi.txt b/Documentation/devicetree/bindings/spi/jcore,spi.txt new file mode 100644 index 000000000000..93936d16e139 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/jcore,spi.txt @@ -0,0 +1,34 @@ +J-Core SPI master + +Required properties: + +- compatible: Must be "jcore,spi2". + +- reg: Memory region for registers. + +- #address-cells: Must be 1. + +- #size-cells: Must be 0. + +Optional properties: + +- clocks: If a phandle named "ref_clk" is present, SPI clock speed + programming is relative to the frequency of the indicated clock. + Necessary only if the input clock rate is something other than a + fixed 50 MHz. + +- clock-names: Clock names, one for each phandle in clocks. + +See spi-bus.txt for additional properties not specific to this device. + +Example: + +spi@40 { + compatible = "jcore,spi2"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x40 0x8>; + spi-max-frequency = <25000000>; + clocks = <&bus_clk>; + clock-names = "ref_clk"; +} diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt index 17822860cb98..4b1d6e74c744 100644 --- a/Documentation/devicetree/bindings/spi/spi-bus.txt +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -31,7 +31,7 @@ with max(cs-gpios > hw cs). So if for example the controller has 2 CS lines, and the cs-gpios property looks like this: -cs-gpios = <&gpio1 0 0> <0> <&gpio1 1 0> <&gpio1 2 0>; +cs-gpios = <&gpio1 0 0>, <0>, <&gpio1 1 0>, <&gpio1 2 0>; Then it should be configured so that num_chipselect = 4 with the following mapping: diff --git a/Documentation/devicetree/bindings/spi/spi-meson.txt b/Documentation/devicetree/bindings/spi/spi-meson.txt index bb52a86f3365..dc6d0313324a 100644 --- a/Documentation/devicetree/bindings/spi/spi-meson.txt +++ b/Documentation/devicetree/bindings/spi/spi-meson.txt @@ -7,7 +7,7 @@ NOR memories, without DMA support and a 64-byte unified transmit / receive buffer. Required properties: - - compatible: should be "amlogic,meson6-spifc" + - compatible: should be "amlogic,meson6-spifc" or "amlogic,meson-gxbb-spifc" - reg: physical base address and length of the controller registers - clocks: phandle of the input clock for the baud rate generator - #address-cells: should be 1 diff --git a/Documentation/devicetree/bindings/thermal/thermal.txt b/Documentation/devicetree/bindings/thermal/thermal.txt index 41b817f7b670..88b6ea1ad290 100644 --- a/Documentation/devicetree/bindings/thermal/thermal.txt +++ b/Documentation/devicetree/bindings/thermal/thermal.txt @@ -62,7 +62,7 @@ For more examples of cooling devices, refer to the example sections below. Required properties: - #cooling-cells: Used to provide cooling device specific information Type: unsigned while referring to it. Must be at least 2, in order - Size: one cell to specify minimum and maximum cooling state used + Size: one cell to specify minimum and maximum cooling state used in the reference. The first cell is the minimum cooling state requested and the second cell is the maximum cooling state requested in the reference. @@ -119,7 +119,7 @@ Required properties: Optional property: - contribution: The cooling contribution to the thermal zone of the Type: unsigned referred cooling device at the referred trip point. - Size: one cell The contribution is a ratio of the sum + Size: one cell The contribution is a ratio of the sum of all cooling contributions within a thermal zone. Note: Using the THERMAL_NO_LIMIT (-1UL) constant in the cooling-device phandle @@ -145,7 +145,7 @@ Required properties: Size: one cell - thermal-sensors: A list of thermal sensor phandles and sensor specifier - Type: list of used while monitoring the thermal zone. + Type: list of used while monitoring the thermal zone. phandles + sensor specifier @@ -473,7 +473,7 @@ thermal-zones { <&adc>; /* pcb north */ /* hotspot = 100 * bandgap - 120 * adc + 484 */ - coefficients = <100 -120 484>; + coefficients = <100 -120 484>; trips { ... @@ -502,7 +502,7 @@ from the ADC sensor. The binding would be then: thermal-sensors = <&adc>; /* hotspot = 1 * adc + 6000 */ - coefficients = <1 6000>; + coefficients = <1 6000>; (d) - Board thermal diff --git a/Documentation/devicetree/bindings/timer/moxa,moxart-timer.txt b/Documentation/devicetree/bindings/timer/moxa,moxart-timer.txt index da2d510cae47..e207c11630af 100644 --- a/Documentation/devicetree/bindings/timer/moxa,moxart-timer.txt +++ b/Documentation/devicetree/bindings/timer/moxa,moxart-timer.txt @@ -2,7 +2,9 @@ MOXA ART timer Required properties: -- compatible : Must be "moxa,moxart-timer" +- compatible : Must be one of: + - "moxa,moxart-timer" + - "aspeed,ast2400-timer" - reg : Should contain registers location and length - interrupts : Should contain the timer interrupt number - clocks : Should contain phandle for the clock that drives the counter diff --git a/Documentation/devicetree/bindings/timer/oxsemi,rps-timer.txt b/Documentation/devicetree/bindings/timer/oxsemi,rps-timer.txt index 3ca89cd1caef..d191612539e8 100644 --- a/Documentation/devicetree/bindings/timer/oxsemi,rps-timer.txt +++ b/Documentation/devicetree/bindings/timer/oxsemi,rps-timer.txt @@ -2,7 +2,7 @@ Oxford Semiconductor OXNAS SoCs Family RPS Timer ================================================ Required properties: -- compatible: Should be "oxsemi,ox810se-rps-timer" +- compatible: Should be "oxsemi,ox810se-rps-timer" or "oxsemi,ox820-rps-timer" - reg : Specifies base physical address and size of the registers. - interrupts : The interrupts of the two timers - clocks : The phandle of the timer clock source diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index 341dc67f3472..0e03344e2e8b 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -81,6 +81,8 @@ i.mx specific properties - fsl,usbmisc: phandler of non-core register device, with one argument that indicate usb controller index - disable-over-current: disable over current detect +- over-current-active-high: over current signal polarity is high active, + typically over current signal polarity is low active. - external-vbus-divider: enables off-chip resistor divider for Vbus Example: diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt index 20a68bf2b4e7..7d16ebfaa5a1 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.txt +++ b/Documentation/devicetree/bindings/usb/dwc2.txt @@ -26,7 +26,10 @@ Refer to phy/phy-bindings.txt for generic phy consumer properties - g-use-dma: enable dma usage in gadget driver. - g-rx-fifo-size: size of rx fifo size in gadget mode. - g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget mode. -- g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode. + +Deprecated properties: +- g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) + in gadget mode. Example: diff --git a/Documentation/devicetree/bindings/usb/dwc3-cavium.txt b/Documentation/devicetree/bindings/usb/dwc3-cavium.txt new file mode 100644 index 000000000000..710b782ccf65 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/dwc3-cavium.txt @@ -0,0 +1,28 @@ +Cavium SuperSpeed DWC3 USB SoC controller + +Required properties: +- compatible: Should contain "cavium,octeon-7130-usb-uctl" + +Required child node: +A child node must exist to represent the core DWC3 IP block. The name of +the node is not important. The content of the node is defined in dwc3.txt. + +Example device node: + + uctl@1180069000000 { + compatible = "cavium,octeon-7130-usb-uctl"; + reg = <0x00011800 0x69000000 0x00000000 0x00000100>; + ranges; + #address-cells = <0x00000002>; + #size-cells = <0x00000002>; + refclk-frequency = <0x05f5e100>; + refclk-type-ss = "dlmc_ref_clk0"; + refclk-type-hs = "dlmc_ref_clk0"; + power = <0x00000002 0x00000002 0x00000001>; + xhci@1690000000000 { + compatible = "cavium,octeon-7130-xhci", "synopsys,dwc3"; + reg = <0x00016900 0x00000000 0x00000010 0x00000000>; + interrupt-parent = <0x00000010>; + interrupts = <0x00000009 0x00000004>; + }; + }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 7d7ce089b003..e3e6983288e3 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -13,7 +13,8 @@ Optional properties: in the array is expected to be a handle to the USB2/HS PHY and the second element is expected to be a handle to the USB3/SS PHY - phys: from the *Generic PHY* bindings - - phy-names: from the *Generic PHY* bindings + - phy-names: from the *Generic PHY* bindings; supported names are "usb2-phy" + or "usb3-phy". - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable - snps,disable_scramble_quirk: true when SW should disable data scrambling. Only really useful for FPGA builds. @@ -39,6 +40,11 @@ Optional properties: disabling the suspend signal to the PHY. - snps,dis_rxdet_inp3_quirk: when set core will disable receiver detection in PHY P3 power state. + - snps,dis-u2-freeclk-exists-quirk: when set, clear the u2_freeclk_exists + in GUSB2PHYCFG, specify that USB2 PHY doesn't provide + a free-running PHY clock. + - snps,dis-del-phy-power-chg-quirk: when set core will change PHY power + from P0 to P1/P2/P3 without delay. - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal utmi_l1_suspend_n, false when asserts utmi_sleep_n - snps,hird-threshold: HIRD threshold diff --git a/Documentation/devicetree/bindings/usb/generic.txt b/Documentation/devicetree/bindings/usb/generic.txt index bba825711873..bfadeb1c3bab 100644 --- a/Documentation/devicetree/bindings/usb/generic.txt +++ b/Documentation/devicetree/bindings/usb/generic.txt @@ -11,6 +11,11 @@ Optional properties: "peripheral" and "otg". In case this attribute isn't passed via DT, USB DRD controllers should default to OTG. + - phy_type: tells USB controllers that we want to configure the core to support + a UTMI+ PHY with an 8- or 16-bit interface if UTMI+ is + selected. Valid arguments are "utmi" and "utmi_wide". + In case this isn't passed via DT, USB controllers should + default to HW capability. - otg-rev: tells usb driver the release number of the OTG and EH supplement with which the device and its descriptors are compliant, in binary-coded decimal (i.e. 2.0 is 0200H). This @@ -34,6 +39,7 @@ dwc3@4a030000 { usb-phy = <&usb2_phy>, <&usb3,phy>; maximum-speed = "super-speed"; dr_mode = "otg"; + phy_type = "utmi_wide"; otg-rev = <0x0200>; adp-disable; }; diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt index b6040563e51a..9e18e000339e 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt +++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt @@ -9,6 +9,7 @@ Required properties: - "renesas,usbhs-r8a7793" for r8a7793 (R-Car M2-N) compatible device - "renesas,usbhs-r8a7794" for r8a7794 (R-Car E2) compatible device - "renesas,usbhs-r8a7795" for r8a7795 (R-Car H3) compatible device + - "renesas,usbhs-r8a7796" for r8a7796 (R-Car M3-W) compatible device - "renesas,rcar-gen2-usbhs" for R-Car Gen2 compatible device - "renesas,rcar-gen3-usbhs" for R-Car Gen3 compatible device diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt new file mode 100644 index 000000000000..0536a938e3ab --- /dev/null +++ b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt @@ -0,0 +1,59 @@ +Rockchip SuperSpeed DWC3 USB SoC controller + +Required properties: +- compatible: should contain "rockchip,rk3399-dwc3" for rk3399 SoC +- clocks: A list of phandle + clock-specifier pairs for the + clocks listed in clock-names +- clock-names: Should contain the following: + "ref_clk" Controller reference clk, have to be 24 MHz + "suspend_clk" Controller suspend clk, have to be 24 MHz or 32 KHz + "bus_clk" Master/Core clock, have to be >= 62.5 MHz for SS + operation and >= 30MHz for HS operation + "grf_clk" Controller grf clk + +Required child node: +A child node must exist to represent the core DWC3 IP block. The name of +the node is not important. The content of the node is defined in dwc3.txt. + +Phy documentation is provided in the following places: +Documentation/devicetree/bindings/phy/rockchip,dwc3-usb-phy.txt + +Example device nodes: + + usbdrd3_0: usb@fe800000 { + compatible = "rockchip,rk3399-dwc3"; + clocks = <&cru SCLK_USB3OTG0_REF>, <&cru SCLK_USB3OTG0_SUSPEND>, + <&cru ACLK_USB3OTG0>, <&cru ACLK_USB3_GRF>; + clock-names = "ref_clk", "suspend_clk", + "bus_clk", "grf_clk"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + usbdrd_dwc3_0: dwc3@fe800000 { + compatible = "snps,dwc3"; + reg = <0x0 0xfe800000 0x0 0x100000>; + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; + dr_mode = "otg"; + status = "disabled"; + }; + }; + + usbdrd3_1: usb@fe900000 { + compatible = "rockchip,rk3399-dwc3"; + clocks = <&cru SCLK_USB3OTG1_REF>, <&cru SCLK_USB3OTG1_SUSPEND>, + <&cru ACLK_USB3OTG1>, <&cru ACLK_USB3_GRF>; + clock-names = "ref_clk", "suspend_clk", + "bus_clk", "grf_clk"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + usbdrd_dwc3_1: dwc3@fe900000 { + compatible = "snps,dwc3"; + reg = <0x0 0xfe900000 0x0 0x100000>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; + dr_mode = "otg"; + status = "disabled"; + }; + }; diff --git a/Documentation/devicetree/bindings/usb/usb4604.txt b/Documentation/devicetree/bindings/usb/usb4604.txt new file mode 100644 index 000000000000..82506d17712c --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb4604.txt @@ -0,0 +1,19 @@ +SMSC USB4604 High-Speed Hub Controller + +Required properties: +- compatible: Should be "smsc,usb4604" + +Optional properties: +- reg: Specifies the i2c slave address, it is required and should be 0x2d + if I2C is used. +- reset-gpios: Should specify GPIO for reset. +- initial-mode: Should specify initial mode. + (1 for HUB mode, 2 for STANDBY mode) + +Examples: + usb-hub@2d { + compatible = "smsc,usb4604"; + reg = <0x2d>; + reset-gpios = <&gpx3 5 1>; + initial-mode = <1>; + }; diff --git a/Documentation/devicetree/bindings/usb/usbmisc-imx.txt b/Documentation/devicetree/bindings/usb/usbmisc-imx.txt index 3539d4e7d23e..f1e27faf528e 100644 --- a/Documentation/devicetree/bindings/usb/usbmisc-imx.txt +++ b/Documentation/devicetree/bindings/usb/usbmisc-imx.txt @@ -6,6 +6,7 @@ Required properties: "fsl,imx6q-usbmisc" for imx6q "fsl,vf610-usbmisc" for Vybrid vf610 "fsl,imx6sx-usbmisc" for imx6sx + "fsl,imx7d-usbmisc" for imx7d - reg: Should contain registers location and length Examples: diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 1992aa97d45a..77e985f21707 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -3,8 +3,8 @@ Device tree binding vendor prefix registry. Keep list in alphabetical order. This isn't an exhaustive list, but you should add new prefixes to it before using them to avoid name-space collisions. -abilis Abilis Systems abcn Abracon Corporation +abilis Abilis Systems active-semi Active-Semi International Inc ad Avionic Design GmbH adapteva Adapteva, Inc. @@ -36,6 +36,7 @@ aspeed ASPEED Technology Inc. atlas Atlas Scientific LLC atmel Atmel Corporation auo AU Optronics Corporation +auvidea Auvidea GmbH avago Avago Technologies avic Shanghai AVIC Optoelectronics Co., Ltd. axis Axis Communications AB @@ -75,6 +76,7 @@ digilent Diglent, Inc. dlg Dialog Semiconductor dlink D-Link Corporation dmo Data Modul AG +domintech Domintech Co., Ltd. dptechnics DPTechnics dragino Dragino Technology Co., Limited ea Embedded Artists AB @@ -85,6 +87,7 @@ elan Elan Microelectronic Corp. embest Shenzhen Embest Technology Co., Ltd. emmicro EM Microelectronic energymicro Silicon Laboratories (formerly Energy Micro AS) +engicam Engicam S.r.l. epcos EPCOS AG epfl Ecole Polytechnique Fédérale de Lausanne epson Seiko Epson Corp. @@ -101,8 +104,8 @@ focaltech FocalTech Systems Co.,Ltd fsl Freescale Semiconductor ge General Electric Company geekbuying GeekBuying -GEFanuc GE Fanuc Intelligent Platforms Embedded Systems, Inc. gef GE Fanuc Intelligent Platforms Embedded Systems, Inc. +GEFanuc GE Fanuc Intelligent Platforms Embedded Systems, Inc. geniatech Geniatech, Inc. giantplus Giantplus Technology Co., Ltd. globalscale Globalscale Technologies, Inc. @@ -126,7 +129,6 @@ i2se I2SE GmbH ibm International Business Machines (IBM) idt Integrated Device Technologies, Inc. ifi Ingenieurburo Fur Ic-Technologie (I/F/I) -iom Iomega Corporation img Imagination Technologies Ltd. infineon Infineon Technologies inforce Inforce Computing @@ -135,11 +137,14 @@ innolux Innolux Corporation intel Intel Corporation intercontrol Inter Control Group invensense InvenSense Inc. +iom Iomega Corporation isee ISEE 2007 S.L. isil Intersil issi Integrated Silicon Solutions Inc. +jdi Japan Display Inc. jedec JEDEC Solid State Technology Association karo Ka-Ro electronics GmbH +keithkoep Keith & Koep GmbH keymile Keymile GmbH kinetic Kinetic Technologies kosagi Sutajio Ko-Usagi PTE Ltd. @@ -149,8 +154,8 @@ lantiq Lantiq Semiconductor lenovo Lenovo Group Ltd. lg LG Corporation linux Linux-specific binding -lsi LSI Corp. (LSI Logic) lltc Linear Technology Corporation +lsi LSI Corp. (LSI Logic) marvell Marvell Technology Group Ltd. maxim Maxim Integrated Products meas Measurement Specialties @@ -190,20 +195,20 @@ onnn ON Semiconductor Corp. ontat On Tat Industrial Company opencores OpenCores.org option Option NV +ORCL Oracle Corporation ortustech Ortus Technology Co., Ltd. ovti OmniVision Technologies -ORCL Oracle Corporation oxsemi Oxford Semiconductor, Ltd. panasonic Panasonic Corporation parade Parade Technologies Inc. pericom Pericom Technology Inc. phytec PHYTEC Messtechnik GmbH picochip Picochip Ltd +pixcir PIXCIR MICROELECTRONICS Co., Ltd plathome Plat'Home Co., Ltd. plda PLDA -pixcir PIXCIR MICROELECTRONICS Co., Ltd -pulsedlight PulsedLight, Inc powervr PowerVR (deprecated, use img) +pulsedlight PulsedLight, Inc qca Qualcomm Atheros, Inc. qcom Qualcomm Technologies, Inc qemu QEMU, a generic and open source machine emulator and virtualizer @@ -231,12 +236,13 @@ sgx SGX Sensortech sharp Sharp Corporation si-en Si-En Technology Ltd. sigma Sigma Designs, Inc. +sii Seiko Instruments, Inc. sil Silicon Image silabs Silicon Laboratories +silead Silead Inc. +silergy Silergy Corp. siliconmitus Silicon Mitus, Inc. simtek -sii Seiko Instruments, Inc. -silergy Silergy Corp. sirf SiRF Technology, Inc. sis Silicon Integrated Systems Corp. sitronix Sitronix Technology Corporation @@ -254,9 +260,12 @@ starry Starry Electronic Technology (ShenZhen) Co., LTD startek Startek ste ST-Ericsson stericsson ST-Ericsson +summit Summit microelectronics +sunchip Shenzhen Sunchip Technology Co., Ltd +SUNW Sun Microsystems, Inc +swir Sierra Wireless syna Synaptics Inc. synology Synology, Inc. -SUNW Sun Microsystems, Inc tbs TBS Technologies tcg Trusted Computing Group tcl Toby Churchill Ltd. @@ -265,17 +274,18 @@ technologic Technologic Systems thine THine Electronics, Inc. ti Texas Instruments tlm Trusted Logic Mobility +topeet Topeet toradex Toradex AG toshiba Toshiba Corporation toumaz Toumaz -tplink TP-LINK Technologies Co., Ltd. tpk TPK U.S.A. LLC +tplink TP-LINK Technologies Co., Ltd. tronfy Tronfy tronsmart Tronsmart truly Truly Semiconductors Limited tyan Tyan Computer Corporation -upisemi uPI Semiconductor Corp. uniwest United Western Technologies Corp (UniWest) +upisemi uPI Semiconductor Corp. urt United Radiant Technology Corporation usi Universal Scientific Industrial Co., Ltd. v3 V3 Semiconductor @@ -293,7 +303,7 @@ x-powers X-Powers xes Extreme Engineering Solutions (X-ES) xillybus Xillybus Ltd. xlnx Xilinx -zyxel ZyXEL Communications Corp. zarlink Zarlink Semiconductor zii Zodiac Inflight Innovations zte ZTE Corp. +zyxel ZyXEL Communications Corp. |