diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
39 files changed, 486 insertions, 44 deletions
diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt index 7eece72b1a35..8fe815046140 100644 --- a/Documentation/devicetree/bindings/arm/amlogic.txt +++ b/Documentation/devicetree/bindings/arm/amlogic.txt @@ -2,7 +2,9 @@ Amlogic MesonX device tree bindings ------------------------------------------- Boards with the Amlogic Meson6 SoC shall have the following properties: + Required root node property: + compatible: "amlogic,meson6" -Required root node property: - -compatible = "amlogic,meson6"; +Boards with the Amlogic Meson8 SoC shall have the following properties: + Required root node property: + compatible: "amlogic,meson8"; diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index fc446347ab6d..b2aacbe16ed9 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -227,6 +227,15 @@ nodes to be present and contain the properties described below. # List of phandles to idle state nodes supported by this cpu [3]. + - rockchip,pmu + Usage: optional for systems that have an "enable-method" + property value of "rockchip,rk3066-smp" + While optional, it is the preferred way to get access to + the cpu-core power-domains. + Value type: <phandle> + Definition: Specifies the syscon node controlling the cpu core + power domains. + Example 1 (dual-cluster big.LITTLE system 32-bit): cpus { diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt new file mode 100644 index 000000000000..42941fdefb11 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/sunxi.txt @@ -0,0 +1,12 @@ +Allwinner sunXi Platforms Device Tree Bindings + +Each device tree must specify which Allwinner SoC it uses, +using one of the following compatible strings: + + allwinner,sun4i-a10 + allwinner,sun5i-a10s + allwinner,sun5i-a13 + allwinner,sun6i-a31 + allwinner,sun7i-a20 + allwinner,sun8i-a23 + allwinner,sun9i-a80 diff --git a/Documentation/devicetree/bindings/arm/ux500/power_domain.txt b/Documentation/devicetree/bindings/arm/ux500/power_domain.txt new file mode 100644 index 000000000000..5679d1742d3e --- /dev/null +++ b/Documentation/devicetree/bindings/arm/ux500/power_domain.txt @@ -0,0 +1,35 @@ +* ST-Ericsson UX500 PM Domains + +UX500 supports multiple PM domains which are used to gate power to one or +more peripherals on the SOC. + +The implementation of PM domains for UX500 are based upon the generic PM domain +and use the corresponding DT bindings. + +==PM domain providers== + +Required properties: + - compatible: Must be "stericsson,ux500-pm-domains". + - #power-domain-cells : Number of cells in a power domain specifier, must be 1. + +Example: + pm_domains: pm_domains0 { + compatible = "stericsson,ux500-pm-domains"; + #power-domain-cells = <1>; + }; + +==PM domain consumers== + +Required properties: + - power-domains: A phandle and PM domain specifier. Below are the list of + valid specifiers: + + Index Specifier + ----- --------- + 0 DOMAIN_VAPE + +Example: + sdi0_per1@80126000 { + compatible = "arm,pl18x", "arm,primecell"; + power-domains = <&pm_domains DOMAIN_VAPE> + }; diff --git a/Documentation/devicetree/bindings/ata/sata_rcar.txt b/Documentation/devicetree/bindings/ata/sata_rcar.txt index 1e6111333fa8..80ae87a0784b 100644 --- a/Documentation/devicetree/bindings/ata/sata_rcar.txt +++ b/Documentation/devicetree/bindings/ata/sata_rcar.txt @@ -3,8 +3,10 @@ Required properties: - compatible : should contain one of the following: - "renesas,sata-r8a7779" for R-Car H1 - - "renesas,sata-r8a7790" for R-Car H2 - - "renesas,sata-r8a7791" for R-Car M2 + - "renesas,sata-r8a7790-es1" for R-Car H2 ES1 + - "renesas,sata-r8a7790" for R-Car H2 other than ES1 + - "renesas,sata-r8a7791" for R-Car M2-W + - "renesas,sata-r8a7793" for R-Car M2-N - reg : address and length of the SATA registers; - interrupts : must consist of one interrupt specifier. diff --git a/Documentation/devicetree/bindings/bus/mvebu-mbus.txt b/Documentation/devicetree/bindings/bus/mvebu-mbus.txt index 5fa44f52a0b8..5e16c3ccb061 100644 --- a/Documentation/devicetree/bindings/bus/mvebu-mbus.txt +++ b/Documentation/devicetree/bindings/bus/mvebu-mbus.txt @@ -48,9 +48,12 @@ Required properties: - compatible: Should be set to "marvell,mbus-controller". - reg: Device's register space. - Two entries are expected (see the examples below): - the first one controls the devices decoding window and - the second one controls the SDRAM decoding window. + Two or three entries are expected (see the examples below): + the first one controls the devices decoding window, + the second one controls the SDRAM decoding window and + the third controls the MBus bridge (only with the + marvell,armada370-mbus and marvell,armadaxp-mbus + compatible strings) Example: @@ -67,7 +70,7 @@ Example: mbusc: mbus-controller@20000 { compatible = "marvell,mbus-controller"; - reg = <0x20000 0x100>, <0x20180 0x20>; + reg = <0x20000 0x100>, <0x20180 0x20>, <0x20250 0x8>; }; /* more children ...*/ @@ -126,7 +129,7 @@ are skipped. mbusc: mbus-controller@20000 { compatible = "marvell,mbus-controller"; - reg = <0x20000 0x100>, <0x20180 0x20>; + reg = <0x20000 0x100>, <0x20180 0x20>, <0x20250 0x8>; }; /* more children ...*/ @@ -170,7 +173,7 @@ Using this macro, the above example would be: mbusc: mbus-controller@20000 { compatible = "marvell,mbus-controller"; - reg = <0x20000 0x100>, <0x20180 0x20>; + reg = <0x20000 0x100>, <0x20180 0x20>, <0x20250 0x8>; }; /* other children */ @@ -266,7 +269,7 @@ See the example below, where a more complete device tree is shown: ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>; mbusc: mbus-controller@20000 { - reg = <0x20000 0x100>, <0x20180 0x20>; + reg = <0x20000 0x100>, <0x20180 0x20>, <0x20250 0x8>; }; interrupt-controller@20000 { diff --git a/Documentation/devicetree/bindings/hwmon/ltc2978.txt b/Documentation/devicetree/bindings/hwmon/ltc2978.txt new file mode 100644 index 000000000000..ed2f09dc2483 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/ltc2978.txt @@ -0,0 +1,39 @@ +ltc2978 + +Required properties: +- compatible: should contain one of: + * "lltc,ltc2974" + * "lltc,ltc2977" + * "lltc,ltc2978" + * "lltc,ltc3880" + * "lltc,ltc3883" + * "lltc,ltm4676" +- reg: I2C slave address + +Optional properties: +- regulators: A node that houses a sub-node for each regulator controlled by + the device. Each sub-node is identified using the node's name, with valid + values listed below. The content of each sub-node is defined by the + standard binding for regulators; see regulator.txt. + +Valid names of regulators depend on number of supplies supported per device: + * ltc2974 : vout0 - vout3 + * ltc2977 : vout0 - vout7 + * ltc2978 : vout0 - vout7 + * ltc3880 : vout0 - vout1 + * ltc3883 : vout0 + * ltm4676 : vout0 - vout1 + +Example: +ltc2978@5e { + compatible = "lltc,ltc2978"; + reg = <0x5e>; + regulators { + vout0 { + regulator-name = "FPGA-2.5V"; + }; + vout2 { + regulator-name = "FPGA-1.5V"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt b/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt index ce6a1a072028..8a3c40829899 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt @@ -30,10 +30,6 @@ should only be used when a device has multiple interrupt parents. Example: interrupts-extended = <&intc1 5 1>, <&intc2 1 0>; -A device node may contain either "interrupts" or "interrupts-extended", but not -both. If both properties are present, then the operating system should log an -error and use only the data in "interrupts". - 2) Interrupt controller nodes ----------------------------- diff --git a/Documentation/devicetree/bindings/memory-controllers/mvebu-sdram-controller.txt b/Documentation/devicetree/bindings/memory-controllers/mvebu-sdram-controller.txt new file mode 100644 index 000000000000..89657d1d4cd4 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/mvebu-sdram-controller.txt @@ -0,0 +1,21 @@ +Device Tree bindings for MVEBU SDRAM controllers + +The Marvell EBU SoCs all have a SDRAM controller. The SDRAM controller +differs from one SoC variant to another, but they also share a number +of commonalities. + +For now, this Device Tree binding documentation only documents the +Armada XP SDRAM controller. + +Required properties: + + - compatible: for Armada XP, "marvell,armada-xp-sdram-controller" + - reg: a resource specifier for the register space, which should + include all SDRAM controller registers as per the datasheet. + +Example: + +sdramc@1400 { + compatible = "marvell,armada-xp-sdram-controller"; + reg = <0x1400 0x500>; +}; diff --git a/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt b/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt new file mode 100644 index 000000000000..f64de95a8e8b --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt @@ -0,0 +1,51 @@ +Device-Tree bindings for Atmel's HLCDC (High LCD Controller) MFD driver + +Required properties: + - compatible: value should be one of the following: + "atmel,sama5d3-hlcdc" + - reg: base address and size of the HLCDC device registers. + - clock-names: the name of the 3 clocks requested by the HLCDC device. + Should contain "periph_clk", "sys_clk" and "slow_clk". + - clocks: should contain the 3 clocks requested by the HLCDC device. + - interrupts: should contain the description of the HLCDC interrupt line + +The HLCDC IP exposes two subdevices: + - a PWM chip: see ../pwm/atmel-hlcdc-pwm.txt + - a Display Controller: see ../drm/atmel-hlcdc-dc.txt + +Example: + + hlcdc: hlcdc@f0030000 { + compatible = "atmel,sama5d3-hlcdc"; + reg = <0xf0030000 0x2000>; + clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>; + clock-names = "periph_clk","sys_clk", "slow_clk"; + interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>; + status = "disabled"; + + hlcdc-display-controller { + compatible = "atmel,hlcdc-display-controller"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888>; + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + hlcdc_panel_output: endpoint@0 { + reg = <0>; + remote-endpoint = <&panel_input>; + }; + }; + }; + + hlcdc_pwm: hlcdc-pwm { + compatible = "atmel,hlcdc-pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_pwm>; + #pwm-cells = <3>; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/max77686.txt b/Documentation/devicetree/bindings/mfd/max77686.txt index 678f3cf0b8f0..75fdfaf41831 100644 --- a/Documentation/devicetree/bindings/mfd/max77686.txt +++ b/Documentation/devicetree/bindings/mfd/max77686.txt @@ -34,6 +34,12 @@ to get matched with their hardware counterparts as follow: -BUCKn : for BUCKs, where n can lie in range 1 to 9. example: BUCK1, BUCK5, BUCK9. + Regulators which can be turned off during system suspend: + -LDOn : 2, 6-8, 10-12, 14-16, + -BUCKn : 1-4. + Use standard regulator bindings for it ('regulator-off-in-suspend'). + + Example: max77686@09 { diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt index 11921cc417bf..01e9f30fe678 100644 --- a/Documentation/devicetree/bindings/mfd/max77693.txt +++ b/Documentation/devicetree/bindings/mfd/max77693.txt @@ -27,6 +27,20 @@ Optional properties: [*] refer Documentation/devicetree/bindings/regulator/regulator.txt +- haptic : The MAX77693 haptic device utilises a PWM controlled motor to provide + users with tactile feedback. PWM period and duty-cycle are varied in + order to provide the approprite level of feedback. + + Required properties: + - compatible : Must be "maxim,max77693-hpatic" + - haptic-supply : power supply for the haptic motor + [*] refer Documentation/devicetree/bindings/regulator/regulator.txt + - pwms : phandle to the physical PWM(Pulse Width Modulation) device. + PWM properties should be named "pwms". And number of cell is different + for each pwm device. + To get more informations, please refer to documentaion. + [*] refer Documentation/devicetree/bindings/pwm/pwm.txt + Example: max77693@66 { compatible = "maxim,max77693"; @@ -52,4 +66,11 @@ Example: regulator-boot-on; }; }; + + haptic { + compatible = "maxim,max77693-haptic"; + haptic-supply = <&haptic_supply>; + pwms = <&pwm 0 40000 0>; + pwm-names = "haptic"; + }; }; diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt index 0e4026a6cbbf..57a045016fca 100644 --- a/Documentation/devicetree/bindings/mfd/s2mps11.txt +++ b/Documentation/devicetree/bindings/mfd/s2mps11.txt @@ -1,5 +1,5 @@ -* Samsung S2MPS11, S2MPS14 and S2MPU02 Voltage and Current Regulator +* Samsung S2MPS11, S2MPS13, S2MPS14 and S2MPU02 Voltage and Current Regulator The Samsung S2MPS11 is a multi-function device which includes voltage and current regulators, RTC, charger controller and other sub-blocks. It is @@ -7,8 +7,8 @@ interfaced to the host controller using an I2C interface. Each sub-block is addressed by the host system using different I2C slave addresses. Required properties: -- compatible: Should be "samsung,s2mps11-pmic" or "samsung,s2mps14-pmic" - or "samsung,s2mpu02-pmic". +- compatible: Should be "samsung,s2mps11-pmic" or "samsung,s2mps13-pmic" + or "samsung,s2mps14-pmic" or "samsung,s2mpu02-pmic". - reg: Specifies the I2C slave address of the pmic block. It should be 0x66. Optional properties: @@ -17,8 +17,8 @@ Optional properties: - interrupts: Interrupt specifiers for interrupt sources. Optional nodes: -- clocks: s2mps11 and s5m8767 provide three(AP/CP/BT) buffered 32.768 KHz - outputs, so to register these as clocks with common clock framework +- clocks: s2mps11, s2mps13 and s5m8767 provide three(AP/CP/BT) buffered 32.768 + KHz outputs, so to register these as clocks with common clock framework instantiate a sub-node named "clocks". It uses the common clock binding documented in : [Documentation/devicetree/bindings/clock/clock-bindings.txt] @@ -30,12 +30,12 @@ Optional nodes: the clock which they consume. Clock ID Devices ---------------------------------------------------------- - 32KhzAP 0 S2MPS11, S2MPS14, S5M8767 - 32KhzCP 1 S2MPS11, S5M8767 - 32KhzBT 2 S2MPS11, S2MPS14, S5M8767 + 32KhzAP 0 S2MPS11, S2MPS13, S2MPS14, S5M8767 + 32KhzCP 1 S2MPS11, S2MPS13, S5M8767 + 32KhzBT 2 S2MPS11, S2MPS13, S2MPS14, S5M8767 - - compatible: Should be one of: "samsung,s2mps11-clk", "samsung,s2mps14-clk", - "samsung,s5m8767-clk" + - compatible: Should be one of: "samsung,s2mps11-clk", "samsung,s2mps13-clk", + "samsung,s2mps14-clk", "samsung,s5m8767-clk" - regulators: The regulators of s2mps11 that have to be instantiated should be included in a sub-node named 'regulators'. Regulator nodes included in this @@ -81,12 +81,14 @@ as per the datasheet of s2mps11. - LDOn - valid values for n are: - S2MPS11: 1 to 38 + - S2MPS13: 1 to 40 - S2MPS14: 1 to 25 - S2MPU02: 1 to 28 - Example: LDO1, LDO2, LDO28 - BUCKn - valid values for n are: - S2MPS11: 1 to 10 + - S2MPS13: 1 to 10 - S2MPS14: 1 to 5 - S2MPU02: 1 to 7 - Example: BUCK1, BUCK2, BUCK9 diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt index 6cd3525d0e09..ee4fc0576c7d 100644 --- a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt @@ -18,6 +18,10 @@ Required Properties: specific extensions. - "samsung,exynos5420-dw-mshc": for controllers with Samsung Exynos5420 specific extensions. + - "samsung,exynos7-dw-mshc": for controllers with Samsung Exynos7 + specific extensions. + - "samsung,exynos7-dw-mshc-smu": for controllers with Samsung Exynos7 + specific extensions having an SMU. * samsung,dw-mshc-ciu-div: Specifies the divider value for the card interface unit (ciu) clock. This property is applicable only for Exynos5 SoC's and diff --git a/Documentation/devicetree/bindings/mmc/img-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/img-dw-mshc.txt new file mode 100644 index 000000000000..85de99fcaa2f --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/img-dw-mshc.txt @@ -0,0 +1,29 @@ +* Imagination specific extensions to the Synopsys Designware Mobile Storage + Host Controller + +The Synopsys designware mobile storage host controller is used to interface +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents +differences between the core Synopsys dw mshc controller properties described +by synopsys-dw-mshc.txt and the properties used by the Imagination specific +extensions to the Synopsys Designware Mobile Storage Host Controller. + +Required Properties: + +* compatible: should be + - "img,pistachio-dw-mshc": for Pistachio SoCs + +Example: + + mmc@18142000 { + compatible = "img,pistachio-dw-mshc"; + reg = <0x18142000 0x400>; + interrupts = <GIC_SHARED 39 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&system_clk>, <&sdhost_clk>; + clock-names = "biu", "ciu"; + + fifo-depth = <0x20>; + bus-width = <4>; + num-slots = <1>; + disable-wp; + }; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt b/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt index 86223c3eda90..4dd6deb90719 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt @@ -12,6 +12,10 @@ Required properties: * for "marvell,armada-380-sdhci", two register areas. The first one for the SDHCI registers themselves, and the second one for the AXI/Mbus bridge registers of the SDHCI unit. +- clocks: Array of clocks required for SDHCI; requires at least one for + I/O clock. +- clock-names: Array of names corresponding to clocks property; shall be + "io" for I/O clock and "core" for optional core clock. Optional properties: - mrvl,clk-delay-cycles: Specify a number of cycles to delay for tuning. @@ -23,6 +27,8 @@ sdhci@d4280800 { reg = <0xd4280800 0x800>; bus-width = <8>; interrupts = <27>; + clocks = <&chip CLKID_SDIO1XIN>, <&chip CLKID_SDIO1>; + clock-names = "io", "core"; non-removable; mrvl,clk-delay-cycles = <31>; }; @@ -32,5 +38,6 @@ sdhci@d8000 { reg = <0xd8000 0x1000>, <0xdc000 0x100>; interrupts = <0 25 0x4>; clocks = <&gateclk 17>; + clock-names = "io"; mrvl,clk-delay-cycles = <0x1F>; }; diff --git a/Documentation/devicetree/bindings/nios2/nios2.txt b/Documentation/devicetree/bindings/nios2/nios2.txt new file mode 100644 index 000000000000..d6d0a94cb3bb --- /dev/null +++ b/Documentation/devicetree/bindings/nios2/nios2.txt @@ -0,0 +1,62 @@ +* Nios II Processor Binding + +This binding specifies what properties available in the device tree +representation of a Nios II Processor Core. + +Users can use sopc2dts tool for generating device tree sources (dts) from a +Qsys system. See more detail in: http://www.alterawiki.com/wiki/Sopc2dts + +Required properties: + +- compatible: Compatible property value should be "altr,nios2-1.0". +- reg: Contains CPU index. +- interrupt-controller: Specifies that the node is an interrupt controller +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt source, should be 1. +- clock-frequency: Contains the clock frequency for CPU, in Hz. +- dcache-line-size: Contains data cache line size. +- icache-line-size: Contains instruction line size. +- dcache-size: Contains data cache size. +- icache-size: Contains instruction cache size. +- altr,pid-num-bits: Specifies the number of bits to use to represent the process + identifier (PID). +- altr,tlb-num-ways: Specifies the number of set-associativity ways in the TLB. +- altr,tlb-num-entries: Specifies the number of entries in the TLB. +- altr,tlb-ptr-sz: Specifies size of TLB pointer. +- altr,has-mul: Specifies CPU hardware multipy support, should be 1. +- altr,has-mmu: Specifies CPU support MMU support, should be 1. +- altr,has-initda: Specifies CPU support initda instruction, should be 1. +- altr,reset-addr: Specifies CPU reset address +- altr,fast-tlb-miss-addr: Specifies CPU fast TLB miss exception address +- altr,exception-addr: Specifies CPU exception address + +Optional properties: +- altr,has-div: Specifies CPU hardware divide support +- altr,implementation: Nios II core implementation, this should be "fast"; + +Example: + +cpu@0x0 { + device_type = "cpu"; + compatible = "altr,nios2-1.0"; + reg = <0>; + interrupt-controller; + #interrupt-cells = <1>; + clock-frequency = <125000000>; + dcache-line-size = <32>; + icache-line-size = <32>; + dcache-size = <32768>; + icache-size = <32768>; + altr,implementation = "fast"; + altr,pid-num-bits = <8>; + altr,tlb-num-ways = <16>; + altr,tlb-num-entries = <128>; + altr,tlb-ptr-sz = <7>; + altr,has-div = <1>; + altr,has-mul = <1>; + altr,reset-addr = <0xc2800000>; + altr,fast-tlb-miss-addr = <0xc7fff400>; + altr,exception-addr = <0xd0000020>; + altr,has-initda = <1>; + altr,has-mmu = <1>; +}; diff --git a/Documentation/devicetree/bindings/nios2/timer.txt b/Documentation/devicetree/bindings/nios2/timer.txt new file mode 100644 index 000000000000..904a5846d7ac --- /dev/null +++ b/Documentation/devicetree/bindings/nios2/timer.txt @@ -0,0 +1,19 @@ +Altera Timer + +Required properties: + +- compatible : should be "altr,timer-1.0" +- reg : Specifies base physical address and size of the registers. +- interrupt-parent: phandle of the interrupt controller +- interrupts : Should contain the timer interrupt number +- clock-frequency : The frequency of the clock that drives the counter, in Hz. + +Example: + +timer { + compatible = "altr,timer-1.0"; + reg = <0x00400000 0x00000020>; + interrupt-parent = <&cpu>; + interrupts = <11>; + clock-frequency = <125000000>; +}; diff --git a/Documentation/devicetree/bindings/pci/pci.txt b/Documentation/devicetree/bindings/pci/pci.txt index 41aeed38926d..f8fbe9af7b2f 100644 --- a/Documentation/devicetree/bindings/pci/pci.txt +++ b/Documentation/devicetree/bindings/pci/pci.txt @@ -7,3 +7,14 @@ And for the interrupt mapping part: Open Firmware Recommended Practice: Interrupt Mapping http://www.openfirmware.org/1275/practice/imap/imap0_9d.pdf + +Additionally to the properties specified in the above standards a host bridge +driver implementation may support the following properties: + +- linux,pci-domain: + If present this property assigns a fixed PCI domain number to a host bridge, + otherwise an unstable (across boots) unique number will be assigned. + It is required to either not set this property at all or set it for all + host bridges in the system, otherwise potentially conflicting domain numbers + may be assigned to root buses behind different host bridges. The domain + number for each host bridge in the system must be unique. diff --git a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt index a186181c402b..51b943cc9770 100644 --- a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt @@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -TZ1090-PDC's pin configuration nodes act as a container for an abitrary number +TZ1090-PDC's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt index 4b27c99f7f9d..49d0e6050940 100644 --- a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt @@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -TZ1090's pin configuration nodes act as a container for an abitrary number of +TZ1090's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt b/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt index daa768956069..ac4da9fe07bd 100644 --- a/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt +++ b/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt @@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -Lantiq's pin configuration nodes act as a container for an abitrary number of +Lantiq's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those group(s), and two pin configuration parameters: diff --git a/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt b/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt index b5469db1d7ad..e89b4677567d 100644 --- a/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt +++ b/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt @@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -Lantiq's pin configuration nodes act as a container for an abitrary number of +Lantiq's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those group(s), and two pin configuration parameters: diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt index 61e73cde9ae9..3c8ce28baad6 100644 --- a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt @@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -Tegra's pin configuration nodes act as a container for an abitrary number of +Tegra's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt index c596a6ad3285..5f55be59d914 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt @@ -13,7 +13,7 @@ Optional properties: Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices. -SiRFprimaII's pinmux nodes act as a container for an abitrary number of subnodes. +SiRFprimaII's pinmux nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a group of pins. Required subnode-properties: diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt index b4480d5c3aca..458615596946 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt @@ -32,7 +32,7 @@ Required properties: Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices. -SPEAr's pinmux nodes act as a container for an abitrary number of subnodes. Each +SPEAr's pinmux nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents muxing for a pin, a group, or a list of pins or groups. diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt index 2fb90b37aa09..a7bde64798c7 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt @@ -18,7 +18,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -Qualcomm's pin configuration nodes act as a container for an abitrary number of +Qualcomm's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt index ffafa1990a30..c4ea61ac56f2 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt @@ -47,7 +47,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -The pin configuration nodes act as a container for an abitrary number of +The pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt index e33e4dcdce79..6e88e91feb11 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt @@ -18,7 +18,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -Qualcomm's pin configuration nodes act as a container for an abitrary number of +Qualcomm's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt index 93b7de91b9f6..eb8d8aa41f20 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt @@ -47,7 +47,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -The pin configuration nodes act as a container for an abitrary number of +The pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt index d2ea80dc43eb..e4d6a9d20f7d 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt @@ -18,7 +18,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -Qualcomm's pin configuration nodes act as a container for an abitrary number of +Qualcomm's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/power/power-controller.txt b/Documentation/devicetree/bindings/power/power-controller.txt new file mode 100644 index 000000000000..4f7a3bc9c407 --- /dev/null +++ b/Documentation/devicetree/bindings/power/power-controller.txt @@ -0,0 +1,18 @@ +* Generic system power control capability + +Power-management integrated circuits or miscellaneous hardware components are +sometimes able to control the system power. The device driver associated with these +components might need to define this capability, which tells the kernel that +it can be used to switch off the system. The corresponding device must have the +standard property "system-power-controller" in its device node. This property +marks the device as able to control the system power. In order to test if this +property is found programmatically, use the helper function +"of_device_is_system_power_controller" from of.h . + +Example: + +act8846: act8846@5 { + compatible = "active-semi,act8846"; + status = "okay"; + system-power-controller; +} diff --git a/Documentation/devicetree/bindings/power_supply/imx-snvs-poweroff.txt b/Documentation/devicetree/bindings/power_supply/imx-snvs-poweroff.txt new file mode 100644 index 000000000000..dc7c9bad63ea --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/imx-snvs-poweroff.txt @@ -0,0 +1,23 @@ +i.mx6 Poweroff Driver + +SNVS_LPCR in SNVS module can power off the whole system by pull +PMIC_ON_REQ low if PMIC_ON_REQ is connected with external PMIC. +If you don't want to use PMIC_ON_REQ as power on/off control, +please set status='disabled' to disable this driver. + +Required Properties: +-compatible: "fsl,sec-v4.0-poweroff" +-reg: Specifies the physical address of the SNVS_LPCR register + +Example: + snvs@020cc000 { + compatible = "fsl,sec-v4.0-mon", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x020cc000 0x4000>; + ..... + snvs_poweroff: snvs-poweroff@38 { + compatible = "fsl,sec-v4.0-poweroff"; + reg = <0x38 0x4>; + }; + } diff --git a/Documentation/devicetree/bindings/regulator/act8865-regulator.txt b/Documentation/devicetree/bindings/regulator/act8865-regulator.txt index 865614b34d6f..dad6358074ac 100644 --- a/Documentation/devicetree/bindings/regulator/act8865-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/act8865-regulator.txt @@ -5,6 +5,10 @@ Required properties: - compatible: "active-semi,act8846" or "active-semi,act8865" - reg: I2C slave address +Optional properties: +- system-power-controller: Telling whether or not this pmic is controlling + the system power. See Documentation/devicetree/bindings/power/power-controller.txt . + Any standard regulator properties can be used to configure the single regulator. The valid names for regulators are: diff --git a/Documentation/devicetree/bindings/regulator/max77802.txt b/Documentation/devicetree/bindings/regulator/max77802.txt index 5aeaffc0f1f0..79e5476444f7 100644 --- a/Documentation/devicetree/bindings/regulator/max77802.txt +++ b/Documentation/devicetree/bindings/regulator/max77802.txt @@ -25,6 +25,29 @@ with their hardware counterparts as follow. The valid names are: example: LDO1, LDO2, LDO35. -BUCKn : for BUCKs, where n can lie in range 1 to 10. example: BUCK1, BUCK5, BUCK10. + +The max77802 regulator supports two different operating modes: Normal and Low +Power Mode. Some regulators support the modes to be changed at startup or by +the consumers during normal operation while others only support to change the +mode during system suspend. The standard regulator suspend states binding can +be used to configure the regulator operating mode. + +The regulators that support the standard "regulator-initial-mode" property, +changing their mode during normal operation are: LDOs 1, 3, 20 and 21. + +The possible values for "regulator-initial-mode" and "regulator-mode" are: + 1: Normal regulator voltage output mode. + 3: Low Power which reduces the quiescent current down to only 1uA + +The list of valid modes are defined in the dt-bindings/clock/maxim,max77802.h +header and can be included by device tree source files. + +The standard "regulator-mode" property can only be used for regulators that +support changing their mode to Low Power Mode during suspend. These regulators +are: BUCKs 2-4 and LDOs 1-35. Also, it only takes effect if the regulator has +been enabled for the given suspend state using "regulator-on-in-suspend" and +has not been disabled for that state using "regulator-off-in-suspend". + Example: max77802@09 { @@ -36,11 +59,23 @@ Example: #size-cells = <0>; regulators { + ldo1_reg: LDO1 { + regulator-name = "vdd_1v0"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-initial-mode = <MAX77802_OPMODE_LP>; + }; + ldo11_reg: LDO11 { regulator-name = "vdd_ldo11"; regulator-min-microvolt = <1900000>; regulator-max-microvolt = <1900000>; regulator-always-on; + regulator-state-mem { + regulator-on-in-suspend; + regulator-mode = <MAX77802_OPMODE_LP>; + }; }; buck1_reg: BUCK1 { diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 86074334e342..abb26b58c83e 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -19,6 +19,24 @@ Optional properties: design requires. This property describes the total system ramp time required due to the combination of internal ramping of the regulator itself, and board design issues such as trace capacitance and load on the supply. +- regulator-state-mem sub-root node for Suspend-to-RAM mode + : suspend to memory, the device goes to sleep, but all data stored in memory, + only some external interrupt can wake the device. +- regulator-state-disk sub-root node for Suspend-to-DISK mode + : suspend to disk, this state operates similarly to Suspend-to-RAM, + but includes a final step of writing memory contents to disk. +- regulator-state-[mem/disk] node has following common properties: + - regulator-on-in-suspend: regulator should be on in suspend state. + - regulator-off-in-suspend: regulator should be off in suspend state. + - regulator-suspend-microvolt: regulator should be set to this voltage + in suspend. + - regulator-mode: operating mode in the given suspend state. + The set of possible operating modes depends on the capabilities of + every hardware so the valid modes are documented on each regulator + device tree binding document. +- regulator-initial-mode: initial operating mode. The set of possible operating + modes depends on the capabilities of every hardware so each device binding + documentation explains which values the regulator supports. Deprecated properties: - regulator-compatible: If a regulator chip contains multiple @@ -34,6 +52,10 @@ Example: regulator-max-microvolt = <2500000>; regulator-always-on; vin-supply = <&vin>; + + regulator-state-mem { + regulator-on-in-suspend; + }; }; Regulator Consumers: diff --git a/Documentation/devicetree/bindings/regulator/sky81452-regulator.txt b/Documentation/devicetree/bindings/regulator/sky81452-regulator.txt index 882455e9b36d..f9acbc1f3c6b 100644 --- a/Documentation/devicetree/bindings/regulator/sky81452-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/sky81452-regulator.txt @@ -1,6 +1,7 @@ SKY81452 voltage regulator Required properties: +- regulator node named lout. - any required generic properties defined in regulator.txt Optional properties: @@ -9,8 +10,9 @@ Optional properties: Example: regulator { - /* generic regulator properties */ - regulator-name = "touch_en"; - regulator-min-microvolt = <4500000>; - regulator-max-microvolt = <8000000>; + lout { + regulator-name = "sky81452-lout"; + regulator-min-microvolt = <4500000>; + regulator-max-microvolt = <8000000>; + }; }; diff --git a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt index 0ef00be44b01..43404b197933 100644 --- a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt @@ -7,7 +7,10 @@ Required properties: - "renesas,thermal-r8a73a4" (R-Mobile AP6) - "renesas,thermal-r8a7779" (R-Car H1) - "renesas,thermal-r8a7790" (R-Car H2) - - "renesas,thermal-r8a7791" (R-Car M2) + - "renesas,thermal-r8a7791" (R-Car M2-W) + - "renesas,thermal-r8a7792" (R-Car V2H) + - "renesas,thermal-r8a7793" (R-Car M2-N) + - "renesas,thermal-r8a7794" (R-Car E2) - reg : Address range of the thermal registers. The 1st reg will be recognized as common register if it has "interrupts". diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 723999d73744..ecaf2035c2fe 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -34,6 +34,7 @@ chipidea Chipidea, Inc chrp Common Hardware Reference Platform chunghwa Chunghwa Picture Tubes Ltd. cirrus Cirrus Logic, Inc. +cnm Chips&Media, Inc. cortina Cortina Systems, Inc. crystalfontz Crystalfontz America, Inc. dallas Maxim Integrated Products (formerly Dallas Semiconductor) @@ -90,8 +91,10 @@ lltc Linear Technology Corporation marvell Marvell Technology Group Ltd. maxim Maxim Integrated Products mediatek MediaTek Inc. +merrii Merrii Technology Co., Ltd. micrel Micrel Inc. microchip Microchip Technology Inc. +micron Micron Technology Inc. mitsubishi Mitsubishi Electric Corporation mosaixtech Mosaix Technologies, Inc. moxa Moxa @@ -127,6 +130,7 @@ renesas Renesas Electronics Corporation ricoh Ricoh Co. Ltd. rockchip Fuzhou Rockchip Electronics Co., Ltd samsung Samsung Semiconductor +sandisk Sandisk Corporation sbs Smart Battery System schindler Schindler seagate Seagate Technology PLC @@ -138,7 +142,7 @@ silergy Silergy Corp. sirf SiRF Technology, Inc. sitronix Sitronix Technology Corporation smsc Standard Microsystems Corporation -snps Synopsys, Inc. +snps Synopsys, Inc. solidrun SolidRun sony Sony Corporation spansion Spansion Inc. |