diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
62 files changed, 1943 insertions, 230 deletions
diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt index 5d5bd456d9d9..e30fd106df4f 100644 --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -10,6 +10,7 @@ PHYs. Required properties: - compatible : compatible string, one of: - "allwinner,sun4i-a10-ahci" + - "allwinner,sun8i-r40-ahci" - "brcm,iproc-ahci" - "hisilicon,hisi-ahci" - "cavium,octeon-7130-ahci" @@ -31,8 +32,10 @@ Optional properties: - clocks : a list of phandle + clock specifier pairs - resets : a list of phandle + reset specifier pairs - target-supply : regulator for SATA target power +- phy-supply : regulator for PHY power - phys : reference to the SATA PHY node - phy-names : must be "sata-phy" +- ahci-supply : regulator for AHCI controller - ports-implemented : Mask that indicates which ports that the HBA supports are available for software to use. Useful if PORTS_IMPL is not programmed by the BIOS, which is true with @@ -42,12 +45,13 @@ Required properties when using sub-nodes: - #address-cells : number of cells to encode an address - #size-cells : number of cells representing the size of an address +For allwinner,sun8i-r40-ahci, the reset propertie must be present. Sub-nodes required properties: - reg : the port number And at least one of the following properties: - phys : reference to the SATA PHY node -- target-supply : regulator for SATA target power +- target-supply : regulator for SATA target power Examples: sata@ffe08000 { diff --git a/Documentation/devicetree/bindings/ata/brcm,sata-brcm.txt b/Documentation/devicetree/bindings/ata/brcm,sata-brcm.txt index 0a5b3b47f217..7713a413c6a7 100644 --- a/Documentation/devicetree/bindings/ata/brcm,sata-brcm.txt +++ b/Documentation/devicetree/bindings/ata/brcm,sata-brcm.txt @@ -9,6 +9,7 @@ Required properties: "brcm,bcm7445-ahci" "brcm,bcm-nsp-ahci" "brcm,sata3-ahci" + "brcm,bcm63138-ahci" - reg : register mappings for AHCI and SATA_TOP_CTRL - reg-names : "ahci" and "top-ctrl" - interrupts : interrupt mapping for SATA IRQ diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index a7c31de29362..f0ba154b5723 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -1,18 +1,9 @@ Specifying GPIO information for devices -============================================ +======================================= 1) gpios property ----------------- -Nodes that makes use of GPIOs should specify them using one or more -properties, each containing a 'gpio-list': - - gpio-list ::= <single-gpio> [gpio-list] - single-gpio ::= <gpio-phandle> <gpio-specifier> - gpio-phandle : phandle to gpio controller node - gpio-specifier : Array of #gpio-cells specifying specific gpio - (controller specific) - GPIO properties should be named "[<name>-]gpios", with <name> being the purpose of this GPIO for the device. While a non-existent <name> is considered valid for compatibility reasons (resolving to the "gpios" property), it is not allowed @@ -33,33 +24,27 @@ The following example could be used to describe GPIO pins used as device enable and bit-banged data signals: gpio1: gpio1 { - gpio-controller - #gpio-cells = <2>; - }; - gpio2: gpio2 { - gpio-controller - #gpio-cells = <1>; + gpio-controller; + #gpio-cells = <2>; }; [...] - enable-gpios = <&gpio2 2>; data-gpios = <&gpio1 12 0>, <&gpio1 13 0>, <&gpio1 14 0>, <&gpio1 15 0>; -Note that gpio-specifier length is controller dependent. In the -above example, &gpio1 uses 2 cells to specify a gpio, while &gpio2 -only uses one. +In the above example, &gpio1 uses 2 cells to specify a gpio. The first cell is +a local offset to the GPIO line and the second cell represent consumer flags, +such as if the consumer desire the line to be active low (inverted) or open +drain. This is the recommended practice. -gpio-specifier may encode: bank, pin position inside the bank, -whether pin is open-drain and whether pin is logically inverted. +The exact meaning of each specifier cell is controller specific, and must be +documented in the device tree binding for the device, but it is strongly +recommended to use the two-cell approach. -Exact meaning of each specifier cell is controller specific, and must -be documented in the device tree binding for the device. - -Most controllers are however specifying a generic flag bitfield -in the last cell, so for these, use the macros defined in +Most controllers are specifying a generic flag bitfield in the last cell, so +for these, use the macros defined in include/dt-bindings/gpio/gpio.h whenever possible: Example of a node using GPIOs: @@ -236,46 +221,40 @@ Example of two SOC GPIO banks defined as gpio-controller nodes: Some or all of the GPIOs provided by a GPIO controller may be routed to pins on the package via a pin controller. This allows muxing those pins between -GPIO and other functions. +GPIO and other functions. It is a fairly common practice among silicon +engineers. + +2.2) Ordinary (numerical) GPIO ranges +------------------------------------- It is useful to represent which GPIOs correspond to which pins on which pin -controllers. The gpio-ranges property described below represents this, and -contains information structures as follows: - - gpio-range-list ::= <single-gpio-range> [gpio-range-list] - single-gpio-range ::= <numeric-gpio-range> | <named-gpio-range> - numeric-gpio-range ::= - <pinctrl-phandle> <gpio-base> <pinctrl-base> <count> - named-gpio-range ::= <pinctrl-phandle> <gpio-base> '<0 0>' - pinctrl-phandle : phandle to pin controller node - gpio-base : Base GPIO ID in the GPIO controller - pinctrl-base : Base pinctrl pin ID in the pin controller - count : The number of GPIOs/pins in this range - -The "pin controller node" mentioned above must conform to the bindings -described in ../pinctrl/pinctrl-bindings.txt. - -In case named gpio ranges are used (ranges with both <pinctrl-base> and -<count> set to 0), the property gpio-ranges-group-names contains one string -for every single-gpio-range in gpio-ranges: - gpiorange-names-list ::= <gpiorange-name> [gpiorange-names-list] - gpiorange-name : Name of the pingroup associated to the GPIO range in - the respective pin controller. - -Elements of gpiorange-names-list corresponding to numeric ranges contain -the empty string. Elements of gpiorange-names-list corresponding to named -ranges contain the name of a pin group defined in the respective pin -controller. The number of pins/GPIOs in the range is the number of pins in -that pin group. +controllers. The gpio-ranges property described below represents this with +a discrete set of ranges mapping pins from the pin controller local number space +to pins in the GPIO controller local number space. -Previous versions of this binding required all pin controller nodes that -were referenced by any gpio-ranges property to contain a property named -#gpio-range-cells with value <3>. This requirement is now deprecated. -However, that property may still exist in older device trees for -compatibility reasons, and would still be required even in new device -trees that need to be compatible with older software. +The format is: <[pin controller phandle], [GPIO controller offset], + [pin controller offset], [number of pins]>; + +The GPIO controller offset pertains to the GPIO controller node containing the +range definition. + +The pin controller node referenced by the phandle must conform to the bindings +described in pinctrl/pinctrl-bindings.txt. + +Each offset runs from 0 to N. It is perfectly fine to pile any number of +ranges with just one pin-to-GPIO line mapping if the ranges are concocted, but +in practice these ranges are often lumped in discrete sets. + +Example: + + gpio-ranges = <&foo 0 20 10>, <&bar 10 50 20>; -Example 1: +This means: +- pins 20..29 on pin controller "foo" is mapped to GPIO line 0..9 and +- pins 50..69 on pin controller "bar" is mapped to GPIO line 10..29 + + +Verbose example: qe_pio_e: gpio-controller@1460 { #gpio-cells = <2>; @@ -289,7 +268,28 @@ Here, a single GPIO controller has GPIOs 0..9 routed to pin controller pinctrl1's pins 20..29, and GPIOs 10..29 routed to pin controller pinctrl2's pins 50..69. -Example 2: + +2.3) GPIO ranges from named pin groups +-------------------------------------- + +It is also possible to use pin groups for gpio ranges when pin groups are the +easiest and most convenient mapping. + +Both both <pinctrl-base> and <count> must set to 0 when using named pin groups +names. + +The property gpio-ranges-group-names must contain exactly one string for each +range. + +Elements of gpio-ranges-group-names must contain the name of a pin group +defined in the respective pin controller. The number of pins/GPIO lines in the +range is the number of pins in that pin group. The number of pins of that +group is defined int the implementation and not in the device tree. + +If numerical and named pin groups are mixed, the string corresponding to a +numerical pin range in gpio-ranges-group-names must be empty. + +Example: gpio_pio_i: gpio-controller@14b0 { #gpio-cells = <2>; @@ -306,6 +306,14 @@ Example 2: "bar"; }; -Here, three GPIO ranges are defined wrt. two pin controllers. pinctrl1 GPIO -ranges are defined using pin numbers whereas the GPIO ranges wrt. pinctrl2 -are named "foo" and "bar". +Here, three GPIO ranges are defined referring to two pin controllers. + +pinctrl1 GPIO ranges are defined using pin numbers whereas the GPIO ranges +in pinctrl2 are defined using the pin groups named "foo" and "bar". + +Previous versions of this binding required all pin controller nodes that +were referenced by any gpio-ranges property to contain a property named +#gpio-range-cells with value <3>. This requirement is now deprecated. +However, that property may still exist in older device trees for +compatibility reasons, and would still be required even in new device +trees that need to be compatible with older software. diff --git a/Documentation/devicetree/bindings/gpio/ingenic,gpio.txt b/Documentation/devicetree/bindings/gpio/ingenic,gpio.txt deleted file mode 100644 index 7988aeb725f4..000000000000 --- a/Documentation/devicetree/bindings/gpio/ingenic,gpio.txt +++ /dev/null @@ -1,46 +0,0 @@ -Ingenic jz47xx GPIO controller - -That the Ingenic GPIO driver node must be a sub-node of the Ingenic pinctrl -driver node. - -Required properties: --------------------- - - - compatible: Must contain one of: - - "ingenic,jz4740-gpio" - - "ingenic,jz4770-gpio" - - "ingenic,jz4780-gpio" - - reg: The GPIO bank number. - - interrupt-controller: Marks the device node as an interrupt controller. - - interrupts: Interrupt specifier for the controllers interrupt. - - #interrupt-cells: Should be 2. Refer to - ../interrupt-controller/interrupts.txt for more details. - - gpio-controller: Marks the device node as a GPIO controller. - - #gpio-cells: Should be 2. The first cell is the GPIO number and the second - cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the - GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. - - gpio-ranges: Range of pins managed by the GPIO controller. Refer to - 'gpio.txt' in this directory for more details. - -Example: --------- - -&pinctrl { - #address-cells = <1>; - #size-cells = <0>; - - gpa: gpio@0 { - compatible = "ingenic,jz4740-gpio"; - reg = <0>; - - gpio-controller; - gpio-ranges = <&pinctrl 0 0 32>; - #gpio-cells = <2>; - - interrupt-controller; - #interrupt-cells = <2>; - - interrupt-parent = <&intc>; - interrupts = <28>; - }; -}; diff --git a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt index 4018ee57a6af..2889bbcd7416 100644 --- a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt +++ b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -4,8 +4,10 @@ Required Properties: - compatible: should contain one or more of the following: - "renesas,gpio-r8a7743": for R8A7743 (RZ/G1M) compatible GPIO controller. + - "renesas,gpio-r8a7744": for R8A7744 (RZ/G1N) compatible GPIO controller. - "renesas,gpio-r8a7745": for R8A7745 (RZ/G1E) compatible GPIO controller. - "renesas,gpio-r8a77470": for R8A77470 (RZ/G1C) compatible GPIO controller. + - "renesas,gpio-r8a774a1": for R8A774A1 (RZ/G2M) compatible GPIO controller. - "renesas,gpio-r8a7778": for R8A7778 (R-Car M1) compatible GPIO controller. - "renesas,gpio-r8a7779": for R8A7779 (R-Car H1) compatible GPIO controller. - "renesas,gpio-r8a7790": for R8A7790 (R-Car H2) compatible GPIO controller. @@ -22,7 +24,7 @@ Required Properties: - "renesas,gpio-r8a77995": for R8A77995 (R-Car D3) compatible GPIO controller. - "renesas,rcar-gen1-gpio": for a generic R-Car Gen1 GPIO controller. - "renesas,rcar-gen2-gpio": for a generic R-Car Gen2 or RZ/G1 GPIO controller. - - "renesas,rcar-gen3-gpio": for a generic R-Car Gen3 GPIO controller. + - "renesas,rcar-gen3-gpio": for a generic R-Car Gen3 or RZ/G2 GPIO controller. - "renesas,gpio-rcar": deprecated. When compatible with the generic version nodes must list the @@ -38,7 +40,7 @@ Required Properties: - #gpio-cells: Should be 2. The first cell is the GPIO number and the second cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. - - gpio-ranges: Range of pins managed by the GPIO controller. + - gpio-ranges: See gpio.txt. Optional properties: @@ -46,35 +48,44 @@ Optional properties: mandatory if the hardware implements a controllable functional clock for the GPIO instance. -Please refer to gpio.txt in this directory for details of gpio-ranges property -and the common GPIO bindings used by client devices. + - gpio-reserved-ranges: See gpio.txt. + +Please refer to gpio.txt in this directory for the common GPIO bindings used by +client devices. The GPIO controller also acts as an interrupt controller. It uses the default two cells specifier as described in Documentation/devicetree/bindings/ interrupt-controller/interrupts.txt. -Example: R8A7779 (R-Car H1) GPIO controller nodes +Example: R8A77470 (RZ/G1C) GPIO controller nodes - gpio0: gpio@ffc40000 { - compatible = "renesas,gpio-r8a7779", "renesas,rcar-gen1-gpio"; - reg = <0xffc40000 0x2c>; - interrupt-parent = <&gic>; - interrupts = <0 141 0x4>; - #gpio-cells = <2>; - gpio-controller; - gpio-ranges = <&pfc 0 0 32>; - interrupt-controller; - #interrupt-cells = <2>; - }; + gpio0: gpio@e6050000 { + compatible = "renesas,gpio-r8a77470", + "renesas,rcar-gen2-gpio"; + reg = <0 0xe6050000 0 0x50>; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 0 23>; + #interrupt-cells = <2>; + interrupt-controller; + clocks = <&cpg CPG_MOD 912>; + power-domains = <&sysc R8A77470_PD_ALWAYS_ON>; + resets = <&cpg 912>; + }; ... - gpio6: gpio@ffc46000 { - compatible = "renesas,gpio-r8a7779", "renesas,rcar-gen1-gpio"; - reg = <0xffc46000 0x2c>; - interrupt-parent = <&gic>; - interrupts = <0 147 0x4>; - #gpio-cells = <2>; - gpio-controller; - gpio-ranges = <&pfc 0 192 9>; - interrupt-controller; - #interrupt-cells = <2>; - }; + gpio3: gpio@e6053000 { + compatible = "renesas,gpio-r8a77470", + "renesas,rcar-gen2-gpio"; + reg = <0 0xe6053000 0 0x50>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 96 30>; + gpio-reserved-ranges = <17 10>; + #interrupt-cells = <2>; + interrupt-controller; + clocks = <&cpg CPG_MOD 909>; + power-domains = <&sysc R8A77470_PD_ALWAYS_ON>; + resets = <&cpg 909>; + }; diff --git a/Documentation/devicetree/bindings/gpio/snps,creg-gpio.txt b/Documentation/devicetree/bindings/gpio/snps,creg-gpio.txt new file mode 100644 index 000000000000..1b30812b015b --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/snps,creg-gpio.txt @@ -0,0 +1,21 @@ +Synopsys GPIO via CREG (Control REGisters) driver + +Required properties: +- compatible : "snps,creg-gpio-hsdk" or "snps,creg-gpio-axs10x". +- reg : Exactly one register range with length 0x4. +- #gpio-cells : Since the generic GPIO binding is used, the + amount of cells must be specified as 2. The first cell is the + pin number, the second cell is used to specify optional parameters: + See "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt. +- gpio-controller : Marks the device node as a GPIO controller. +- ngpios: Number of GPIO pins. + +Example: + +gpio: gpio@f00014b0 { + compatible = "snps,creg-gpio-hsdk"; + reg = <0xf00014b0 0x4>; + gpio-controller; + #gpio-cells = <2>; + ngpios = <2>; +}; diff --git a/Documentation/devicetree/bindings/hwmon/ina3221.txt b/Documentation/devicetree/bindings/hwmon/ina3221.txt new file mode 100644 index 000000000000..a7b25caa2b8e --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/ina3221.txt @@ -0,0 +1,44 @@ +Texas Instruments INA3221 Device Tree Bindings + +1) ina3221 node + Required properties: + - compatible: Must be "ti,ina3221" + - reg: I2C address + + Optional properties: + = The node contains optional child nodes for three channels = + = Each child node describes the information of input source = + + - #address-cells: Required only if a child node is present. Must be 1. + - #size-cells: Required only if a child node is present. Must be 0. + +2) child nodes + Required properties: + - reg: Must be 0, 1 or 2, corresponding to IN1, IN2 or IN3 port of INA3221 + + Optional properties: + - label: Name of the input source + - shunt-resistor-micro-ohms: Shunt resistor value in micro-Ohm + +Example: + +ina3221@40 { + compatible = "ti,ina3221"; + reg = <0x40>; + #address-cells = <1>; + #size-cells = <0>; + + input@0 { + reg = <0x0>; + status = "disabled"; + }; + input@1 { + reg = <0x1>; + shunt-resistor-micro-ohms = <5000>; + }; + input@2 { + reg = <0x2>; + label = "VDD_5V"; + shunt-resistor-micro-ohms = <5000>; + }; +}; diff --git a/Documentation/devicetree/bindings/hwmon/ltc2978.txt b/Documentation/devicetree/bindings/hwmon/ltc2978.txt index bf2a47bbdc58..b428a70a7cc0 100644 --- a/Documentation/devicetree/bindings/hwmon/ltc2978.txt +++ b/Documentation/devicetree/bindings/hwmon/ltc2978.txt @@ -15,6 +15,7 @@ Required properties: * "lltc,ltm2987" * "lltc,ltm4675" * "lltc,ltm4676" + * "lltc,ltm4686" - reg: I2C slave address Optional properties: @@ -30,6 +31,7 @@ Valid names of regulators depend on number of supplies supported per device: * ltc3880, ltc3882, ltc3886 : vout0 - vout1 * ltc3883 : vout0 * ltm4676 : vout0 - vout1 + * ltm4686 : vout0 - vout1 Example: ltc2978@5e { diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt b/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt index 00e4365d7206..091c8dfd3229 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt @@ -3,7 +3,6 @@ Required properties: - compatible : - "fsl,imx7ulp-lpi2c" for LPI2C compatible with the one integrated on i.MX7ULP soc - - "fsl,imx8dv-lpi2c" for LPI2C compatible with the one integrated on i.MX8DV soc - reg : address and length of the lpi2c master registers - interrupts : lpi2c interrupt - clocks : lpi2c clock specifier @@ -11,7 +10,7 @@ Required properties: Examples: lpi2c7: lpi2c7@40a50000 { - compatible = "fsl,imx8dv-lpi2c"; + compatible = "fsl,imx7ulp-lpi2c"; reg = <0x40A50000 0x10000>; interrupt-parent = <&intc>; interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/input/gpio-keys.txt b/Documentation/devicetree/bindings/input/gpio-keys.txt index 996ce84352cb..7cccc49b6bea 100644 --- a/Documentation/devicetree/bindings/input/gpio-keys.txt +++ b/Documentation/devicetree/bindings/input/gpio-keys.txt @@ -1,4 +1,4 @@ -Device-Tree bindings for input/gpio_keys.c keyboard driver +Device-Tree bindings for input/keyboard/gpio_keys.c keyboard driver Required properties: - compatible = "gpio-keys"; diff --git a/Documentation/devicetree/bindings/interrupt-controller/riscv,cpu-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/riscv,cpu-intc.txt index b0a8af51c388..265b223cd978 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/riscv,cpu-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/riscv,cpu-intc.txt @@ -11,7 +11,7 @@ The RISC-V supervisor ISA manual specifies three interrupt sources that are attached to every HLIC: software interrupts, the timer interrupt, and external interrupts. Software interrupts are used to send IPIs between cores. The timer interrupt comes from an architecturally mandated real-time timer that is -controller via Supervisor Binary Interface (SBI) calls and CSR reads. External +controlled via Supervisor Binary Interface (SBI) calls and CSR reads. External interrupts connect all other device interrupts to the HLIC, which are routed via the platform-level interrupt controller (PLIC). @@ -25,7 +25,15 @@ in the system. Required properties: - compatible : "riscv,cpu-intc" -- #interrupt-cells : should be <1> +- #interrupt-cells : should be <1>. The interrupt sources are defined by the + RISC-V supervisor ISA manual, with only the following three interrupts being + defined for supervisor mode: + - Source 1 is the supervisor software interrupt, which can be sent by an SBI + call and is reserved for use by software. + - Source 5 is the supervisor timer interrupt, which can be configured by + SBI calls and implements a one-shot timer. + - Source 9 is the supervisor external interrupt, which chains to all other + device interrupts. - interrupt-controller : Identifies the node as an interrupt controller Furthermore, this interrupt-controller MUST be embedded inside the cpu @@ -38,7 +46,7 @@ An example device tree entry for a HLIC is show below. ... cpu1-intc: interrupt-controller { #interrupt-cells = <1>; - compatible = "riscv,cpu-intc", "sifive,fu540-c000-cpu-intc"; + compatible = "sifive,fu540-c000-cpu-intc", "riscv,cpu-intc"; interrupt-controller; }; }; diff --git a/Documentation/devicetree/bindings/leds/leds-an30259a.txt b/Documentation/devicetree/bindings/leds/leds-an30259a.txt new file mode 100644 index 000000000000..6ffb861083c0 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-an30259a.txt @@ -0,0 +1,43 @@ +* Panasonic AN30259A 3-channel LED driver + +The AN30259A is a LED controller capable of driving three LEDs independently. It supports +constant current output and sloping current output modes. The chip is connected over I2C. + +Required properties: + - compatible: Must be "panasonic,an30259a". + - reg: I2C slave address. + - #address-cells: Must be 1. + - #size-cells: Must be 0. + +Each LED is represented as a sub-node of the panasonic,an30259a node. + +Required sub-node properties: + - reg: Pin that the LED is connected to. Must be 1, 2, or 3. + +Optional sub-node properties: + - label: see Documentation/devicetree/bindings/leds/common.txt + - linux,default-trigger: see Documentation/devicetree/bindings/leds/common.txt + +Example: +led-controller@30 { + compatible = "panasonic,an30259a"; + reg = <0x30>; + #address-cells = <1>; + #size-cells = <0>; + + led@1 { + reg = <1>; + linux,default-trigger = "heartbeat"; + label = "red:indicator"; + }; + + led@2 { + reg = <2>; + label = "green:indicator"; + }; + + led@3 { + reg = <3>; + label = "blue:indicator"; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt index 3ca56fdb5ffe..a4b056761eaa 100644 --- a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt +++ b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt @@ -1,16 +1,17 @@ -* ROHM BD71837 Power Management Integrated Circuit bindings +* ROHM BD71837 and BD71847 Power Management Integrated Circuit bindings -BD71837MWV is a programmable Power Management IC for powering single-core, -dual-core, and quad-core SoCs such as NXP-i.MX 8M. It is optimized for -low BOM cost and compact solution footprint. It integrates 8 Buck -egulators and 7 LDOs to provide all the power rails required by the SoC and -the commonly used peripherals. +BD71837MWV and BD71847MWV are programmable Power Management ICs for powering +single-core, dual-core, and quad-core SoCs such as NXP-i.MX 8M. They are +optimized for low BOM cost and compact solution footprint. BD71837MWV +integrates 8 Buck regulators and 7 LDOs. BD71847MWV contains 6 Buck regulators +and 6 LDOs. -Datasheet for PMIC is available at: +Datasheet for BD71837 is available at: https://www.rohm.com/datasheet/BD71837MWV/bd71837mwv-e Required properties: - - compatible : Should be "rohm,bd71837". + - compatible : Should be "rohm,bd71837" for bd71837 + "rohm,bd71847" for bd71847. - reg : I2C slave address. - interrupt-parent : Phandle to the parent interrupt controller. - interrupts : The interrupt line the device is connected to. diff --git a/Documentation/devicetree/bindings/mips/mscc.txt b/Documentation/devicetree/bindings/mips/mscc.txt index ae15ec333542..bc817e984628 100644 --- a/Documentation/devicetree/bindings/mips/mscc.txt +++ b/Documentation/devicetree/bindings/mips/mscc.txt @@ -41,3 +41,19 @@ Example: compatible = "mscc,ocelot-cpu-syscon", "syscon"; reg = <0x70000000 0x2c>; }; + +o HSIO regs: + +The SoC has a few registers (HSIO) handling miscellaneous functionalities: +configuration and status of PLL5, RCOMP, SyncE, SerDes configurations and +status, SerDes muxing and a thermal sensor. + +Required properties: +- compatible: Should be "mscc,ocelot-hsio", "syscon", "simple-mfd" +- reg : Should contain registers location and length + +Example: + syscon@10d0000 { + compatible = "mscc,ocelot-hsio", "syscon", "simple-mfd"; + reg = <0x10d0000 0x10000>; + }; diff --git a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt index f6ddba31cb73..e2effe17f05e 100644 --- a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt @@ -15,6 +15,7 @@ Required Properties: - "arasan,sdhci-5.1": generic Arasan SDHCI 5.1 PHY - "rockchip,rk3399-sdhci-5.1", "arasan,sdhci-5.1": rk3399 eMMC PHY For this device it is strongly suggested to include arasan,soc-ctl-syscon. + - "ti,am654-sdhci-5.1", "arasan,sdhci-5.1": TI AM654 MMC PHY - reg: From mmc bindings: Register location and length. - clocks: From clock bindings: Handles to clock inputs. - clock-names: From clock bindings: Tuple including "clk_xin" and "clk_ahb" diff --git a/Documentation/devicetree/bindings/mmc/jz4740.txt b/Documentation/devicetree/bindings/mmc/jz4740.txt index 7cd8c432d7c8..8a6f87f13114 100644 --- a/Documentation/devicetree/bindings/mmc/jz4740.txt +++ b/Documentation/devicetree/bindings/mmc/jz4740.txt @@ -7,6 +7,7 @@ described in mmc.txt. Required properties: - compatible: Should be one of the following: - "ingenic,jz4740-mmc" for the JZ4740 + - "ingenic,jz4725b-mmc" for the JZ4725B - "ingenic,jz4780-mmc" for the JZ4780 - reg: Should contain the MMC controller registers location and length. - interrupts: Should contain the interrupt specifier of the MMC controller. diff --git a/Documentation/devicetree/bindings/mmc/mmci.txt b/Documentation/devicetree/bindings/mmc/mmci.txt index 03796cf2d3e7..6d3c626e017d 100644 --- a/Documentation/devicetree/bindings/mmc/mmci.txt +++ b/Documentation/devicetree/bindings/mmc/mmci.txt @@ -15,8 +15,11 @@ Required properties: Optional properties: - arm,primecell-periphid : contains the PrimeCell Peripheral ID, it overrides the ID provided by the HW +- resets : phandle to internal reset line. + Should be defined for sdmmc variant. - vqmmc-supply : phandle to the regulator device tree node, mentioned as the VCCQ/VDD_IO supply in the eMMC/SD specs. +specific for ux500 variant: - st,sig-dir-dat0 : bus signal direction pin used for DAT[0]. - st,sig-dir-dat2 : bus signal direction pin used for DAT[2]. - st,sig-dir-dat31 : bus signal direction pin used for DAT[3] and DAT[1]. @@ -24,6 +27,14 @@ Optional properties: - st,sig-dir-cmd : cmd signal direction pin used for CMD. - st,sig-pin-fbclk : feedback clock signal pin used. +specific for sdmmc variant: +- st,sig-dir : signal direction polarity used for cmd, dat0 dat123. +- st,neg-edge : data & command phase relation, generated on + sd clock falling edge. +- st,use-ckin : use ckin pin from an external driver to sample + the receive data (example: with voltage + switch transceiver). + Deprecated properties: - mmc-cap-mmc-highspeed : indicates whether MMC is high speed capable. - mmc-cap-sd-highspeed : indicates whether SD is high speed capable. diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.txt b/Documentation/devicetree/bindings/mmc/mtk-sd.txt index f33467a54a05..f5bcda3980cc 100644 --- a/Documentation/devicetree/bindings/mmc/mtk-sd.txt +++ b/Documentation/devicetree/bindings/mmc/mtk-sd.txt @@ -10,6 +10,7 @@ Required properties: - compatible: value should be either of the following. "mediatek,mt8135-mmc": for mmc host ip compatible with mt8135 "mediatek,mt8173-mmc": for mmc host ip compatible with mt8173 + "mediatek,mt8183-mmc": for mmc host ip compatible with mt8183 "mediatek,mt2701-mmc": for mmc host ip compatible with mt2701 "mediatek,mt2712-mmc": for mmc host ip compatible with mt2712 "mediatek,mt7622-mmc": for MT7622 SoC @@ -22,6 +23,7 @@ Required properties: "source" - source clock (required) "hclk" - HCLK which used for host (required) "source_cg" - independent source clock gate (required for MT2712) + "bus_clk" - bus clock used for internal register access (required for MT2712 MSDC0/3) - pinctrl-names: should be "default", "state_uhs" - pinctrl-0: should contain default/high speed pin ctrl - pinctrl-1: should contain uhs mode pin ctrl diff --git a/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt index 9bce57862ed6..32b4b4e41923 100644 --- a/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt @@ -38,3 +38,75 @@ sdhci@c8000200 { power-gpios = <&gpio 155 0>; /* gpio PT3 */ bus-width = <8>; }; + +Optional properties for Tegra210 and Tegra186: +- pinctrl-names, pinctrl-0, pinctrl-1 : Specify pad voltage + configurations. Valid pinctrl-names are "sdmmc-3v3" and "sdmmc-1v8" + for controllers supporting multiple voltage levels. The order of names + should correspond to the pin configuration states in pinctrl-0 and + pinctrl-1. +- nvidia,only-1-8-v : The presence of this property indicates that the + controller operates at a 1.8 V fixed I/O voltage. +- nvidia,pad-autocal-pull-up-offset-3v3, + nvidia,pad-autocal-pull-down-offset-3v3 : Specify drive strength + calibration offsets for 3.3 V signaling modes. +- nvidia,pad-autocal-pull-up-offset-1v8, + nvidia,pad-autocal-pull-down-offset-1v8 : Specify drive strength + calibration offsets for 1.8 V signaling modes. +- nvidia,pad-autocal-pull-up-offset-3v3-timeout, + nvidia,pad-autocal-pull-down-offset-3v3-timeout : Specify drive + strength used as a fallback in case the automatic calibration times + out on a 3.3 V signaling mode. +- nvidia,pad-autocal-pull-up-offset-1v8-timeout, + nvidia,pad-autocal-pull-down-offset-1v8-timeout : Specify drive + strength used as a fallback in case the automatic calibration times + out on a 1.8 V signaling mode. +- nvidia,pad-autocal-pull-up-offset-sdr104, + nvidia,pad-autocal-pull-down-offset-sdr104 : Specify drive strength + calibration offsets for SDR104 mode. +- nvidia,pad-autocal-pull-up-offset-hs400, + nvidia,pad-autocal-pull-down-offset-hs400 : Specify drive strength + calibration offsets for HS400 mode. +- nvidia,default-tap : Specify the default inbound sampling clock + trimmer value for non-tunable modes. +- nvidia,default-trim : Specify the default outbound clock trimmer + value. +- nvidia,dqs-trim : Specify DQS trim value for HS400 timing + + Notes on the pad calibration pull up and pulldown offset values: + - The property values are drive codes which are programmed into the + PD_OFFSET and PU_OFFSET sections of the + SDHCI_TEGRA_AUTO_CAL_CONFIG register. + - A higher value corresponds to higher drive strength. Please refer + to the reference manual of the SoC for correct values. + - The SDR104 and HS400 timing specific values are used in + corresponding modes if specified. + + Notes on tap and trim values: + - The values are used for compensating trace length differences + by adjusting the sampling point. + - The values are programmed to the Vendor Clock Control Register. + Please refer to the reference manual of the SoC for correct + values. + - The DQS trim values are only used on controllers which support + HS400 timing. Only SDMMC4 on Tegra210 and Tegra 186 supports + HS400. + +Example: +sdhci@700b0000 { + compatible = "nvidia,tegra210-sdhci", "nvidia,tegra124-sdhci"; + reg = <0x0 0x700b0000 0x0 0x200>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA210_CLK_SDMMC1>; + clock-names = "sdhci"; + resets = <&tegra_car 14>; + reset-names = "sdhci"; + pinctrl-names = "sdmmc-3v3", "sdmmc-1v8"; + pinctrl-0 = <&sdmmc1_3v3>; + pinctrl-1 = <&sdmmc1_1v8>; + nvidia,pad-autocal-pull-up-offset-3v3 = <0x00>; + nvidia,pad-autocal-pull-down-offset-3v3 = <0x7d>; + nvidia,pad-autocal-pull-up-offset-1v8 = <0x7b>; + nvidia,pad-autocal-pull-down-offset-1v8 = <0x7b>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt index 5ff1e12c655a..c064af5838aa 100644 --- a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt +++ b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt @@ -12,6 +12,7 @@ Required properties: - "renesas,mmcif-r8a73a4" for the MMCIF found in r8a73a4 SoCs - "renesas,mmcif-r8a7740" for the MMCIF found in r8a7740 SoCs - "renesas,mmcif-r8a7743" for the MMCIF found in r8a7743 SoCs + - "renesas,mmcif-r8a7744" for the MMCIF found in r8a7744 SoCs - "renesas,mmcif-r8a7745" for the MMCIF found in r8a7745 SoCs - "renesas,mmcif-r8a7778" for the MMCIF found in r8a7778 SoCs - "renesas,mmcif-r8a7790" for the MMCIF found in r8a7790 SoCs @@ -23,7 +24,8 @@ Required properties: - interrupts: Some SoCs have only 1 shared interrupt, while others have either 2 or 3 individual interrupts (error, int, card detect). Below is the number of interrupts for each SoC: - 1: r8a73a4, r8a7743, r8a7745, r8a7778, r8a7790, r8a7791, r8a7793, r8a7794 + 1: r8a73a4, r8a7743, r8a7744, r8a7745, r8a7778, r8a7790, r8a7791, r8a7793, + r8a7794 2: r8a7740, sh73a0 3: r7s72100 diff --git a/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt b/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt new file mode 100644 index 000000000000..45c9978aad7b --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt @@ -0,0 +1,41 @@ +* Spreadtrum SDHCI controller (sdhci-sprd) + +The Secure Digital (SD) Host controller on Spreadtrum SoCs provides an interface +for MMC, SD and SDIO types of cards. + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-sprd driver. + +Required properties: +- compatible: Should contain "sprd,sdhci-r11". +- reg: physical base address of the controller and length. +- interrupts: Interrupts used by the SDHCI controller. +- clocks: Should contain phandle for the clock feeding the SDHCI controller +- clock-names: Should contain the following: + "sdio" - SDIO source clock (required) + "enable" - gate clock which used for enabling/disabling the device (required) + +Optional properties: +- assigned-clocks: the same with "sdio" clock +- assigned-clock-parents: the default parent of "sdio" clock + +Examples: + +sdio0: sdio@20600000 { + compatible = "sprd,sdhci-r11"; + reg = <0 0x20600000 0 0x1000>; + interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>; + + clock-names = "sdio", "enable"; + clocks = <&ap_clk CLK_EMMC_2X>, + <&apahb_gate CLK_EMMC_EB>; + assigned-clocks = <&ap_clk CLK_EMMC_2X>; + assigned-clock-parents = <&rpll CLK_RPLL_390M>; + + bus-width = <8>; + non-removable; + no-sdio; + no-sd; + cap-mmc-hw-reset; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index c434200d19d5..27f2eab2981d 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -16,7 +16,11 @@ Required properties: "renesas,sdhi-r8a73a4" - SDHI IP on R8A73A4 SoC "renesas,sdhi-r8a7740" - SDHI IP on R8A7740 SoC "renesas,sdhi-r8a7743" - SDHI IP on R8A7743 SoC + "renesas,sdhi-r8a7744" - SDHI IP on R8A7744 SoC "renesas,sdhi-r8a7745" - SDHI IP on R8A7745 SoC + "renesas,sdhi-r8a774a1" - SDHI IP on R8A774A1 SoC + "renesas,sdhi-r8a77470" - SDHI IP on R8A77470 SoC + "renesas,sdhi-mmc-r8a77470" - SDHI/MMC IP on R8A77470 SoC "renesas,sdhi-r8a7778" - SDHI IP on R8A7778 SoC "renesas,sdhi-r8a7779" - SDHI IP on R8A7779 SoC "renesas,sdhi-r8a7790" - SDHI IP on R8A7790 SoC @@ -27,14 +31,16 @@ Required properties: "renesas,sdhi-r8a7795" - SDHI IP on R8A7795 SoC "renesas,sdhi-r8a7796" - SDHI IP on R8A7796 SoC "renesas,sdhi-r8a77965" - SDHI IP on R8A77965 SoC + "renesas,sdhi-r8a77970" - SDHI IP on R8A77970 SoC "renesas,sdhi-r8a77980" - SDHI IP on R8A77980 SoC "renesas,sdhi-r8a77990" - SDHI IP on R8A77990 SoC "renesas,sdhi-r8a77995" - SDHI IP on R8A77995 SoC "renesas,sdhi-shmobile" - a generic sh-mobile SDHI controller "renesas,rcar-gen1-sdhi" - a generic R-Car Gen1 SDHI controller - "renesas,rcar-gen2-sdhi" - a generic R-Car Gen2 or RZ/G1 + "renesas,rcar-gen2-sdhi" - a generic R-Car Gen2 and RZ/G1 SDHI + (not SDHI/MMC) controller + "renesas,rcar-gen3-sdhi" - a generic R-Car Gen3 or RZ/G2 SDHI controller - "renesas,rcar-gen3-sdhi" - a generic R-Car Gen3 SDHI controller When compatible with the generic version, nodes must list diff --git a/Documentation/devicetree/bindings/mmc/uniphier-sd.txt b/Documentation/devicetree/bindings/mmc/uniphier-sd.txt new file mode 100644 index 000000000000..e1d658755722 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/uniphier-sd.txt @@ -0,0 +1,55 @@ +UniPhier SD/eMMC controller + +Required properties: +- compatible: should be one of the following: + "socionext,uniphier-sd-v2.91" - IP version 2.91 + "socionext,uniphier-sd-v3.1" - IP version 3.1 + "socionext,uniphier-sd-v3.1.1" - IP version 3.1.1 +- reg: offset and length of the register set for the device. +- interrupts: a single interrupt specifier. +- clocks: a single clock specifier of the controller clock. +- reset-names: should contain the following: + "host" - mandatory for all versions + "bridge" - should exist only for "socionext,uniphier-sd-v2.91" + "hw" - should exist if eMMC hw reset line is available +- resets: a list of reset specifiers, corresponding to the reset-names + +Optional properties: +- pinctrl-names: if present, should contain the following: + "default" - should exist for all instances + "uhs" - should exist for SD instance with UHS support +- pinctrl-0: pin control state for the default mode +- pinctrl-1: pin control state for the UHS mode +- dma-names: should be "rx-tx" if present. + This property can exist only for "socionext,uniphier-sd-v2.91". +- dmas: a single DMA channel specifier + This property can exist only for "socionext,uniphier-sd-v2.91". +- bus-width: see mmc.txt +- cap-sd-highspeed: see mmc.txt +- cap-mmc-highspeed: see mmc.txt +- sd-uhs-sdr12: see mmc.txt +- sd-uhs-sdr25: see mmc.txt +- sd-uhs-sdr50: see mmc.txt +- cap-mmc-hw-reset: should exist if reset-names contains "hw". see mmc.txt +- non-removable: see mmc.txt + +Example: + + sd: sdhc@5a400000 { + compatible = "socionext,uniphier-sd-v2.91"; + reg = <0x5a400000 0x200>; + interrupts = <0 76 4>; + pinctrl-names = "default", "uhs"; + pinctrl-0 = <&pinctrl_sd>; + pinctrl-1 = <&pinctrl_sd_uhs>; + clocks = <&mio_clk 0>; + reset-names = "host", "bridge"; + resets = <&mio_rst 0>, <&mio_rst 3>; + dma-names = "rx-tx"; + dmas = <&dmac 4>; + bus-width = <4>; + cap-sd-highspeed; + sd-uhs-sdr12; + sd-uhs-sdr25; + sd-uhs-sdr50; + }; diff --git a/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt index 4648948f7c3b..e15589f47787 100644 --- a/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt +++ b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt @@ -19,6 +19,9 @@ Optional properties: - interrupt-names: must be "mdio_done_error" when there is a share interrupt fed to this hardware block, or must be "mdio_done" for the first interrupt and "mdio_error" for the second when there are separate interrupts +- clocks: A reference to the clock supplying the MDIO bus controller +- clock-frequency: the MDIO bus clock that must be output by the MDIO bus + hardware, if absent, the default hardware values are used Child nodes of this MDIO bus controller node are standard Ethernet PHY device nodes as described in Documentation/devicetree/bindings/net/phy.txt diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index 41089369f891..b3acebe08eb0 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -19,6 +19,10 @@ Required properties: - slaves : Specifies number for slaves - active_slave : Specifies the slave to use for time stamping, ethtool and SIOCGMIIPHY +- cpsw-phy-sel : Specifies the phandle to the CPSW phy mode selection + device. See also cpsw-phy-sel.txt for it's binding. + Note that in legacy cases cpsw-phy-sel may be + a child device instead of a phandle. Optional properties: - ti,hwmods : Must be "cpgmac0" @@ -75,6 +79,7 @@ Examples: cpts_clock_mult = <0x80000000>; cpts_clock_shift = <29>; syscon = <&cm>; + cpsw-phy-sel = <&phy_sel>; cpsw_emac0: slave@0 { phy_id = <&davinci_mdio>, <0>; phy-mode = "rgmii-txid"; @@ -103,6 +108,7 @@ Examples: cpts_clock_mult = <0x80000000>; cpts_clock_shift = <29>; syscon = <&cm>; + cpsw-phy-sel = <&phy_sel>; cpsw_emac0: slave@0 { phy_id = <&davinci_mdio>, <0>; phy-mode = "rgmii-txid"; diff --git a/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt b/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt new file mode 100644 index 000000000000..886cbe8ffb38 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt @@ -0,0 +1,143 @@ +Lantiq GSWIP Ethernet switches +================================== + +Required properties for GSWIP core: + +- compatible : "lantiq,xrx200-gswip" for the embedded GSWIP in the + xRX200 SoC +- reg : memory range of the GSWIP core registers + : memory range of the GSWIP MDIO registers + : memory range of the GSWIP MII registers + +See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of +additional required and optional properties. + + +Required properties for MDIO bus: +- compatible : "lantiq,xrx200-mdio" for the MDIO bus inside the GSWIP + core of the xRX200 SoC and the PHYs connected to it. + +See Documentation/devicetree/bindings/net/mdio.txt for a list of additional +required and optional properties. + + +Required properties for GPHY firmware loading: +- compatible : "lantiq,xrx200-gphy-fw", "lantiq,gphy-fw" + "lantiq,xrx300-gphy-fw", "lantiq,gphy-fw" + "lantiq,xrx330-gphy-fw", "lantiq,gphy-fw" + for the loading of the firmware into the embedded + GPHY core of the SoC. +- lantiq,rcu : reference to the rcu syscon + +The GPHY firmware loader has a list of GPHY entries, one for each +embedded GPHY + +- reg : Offset of the GPHY firmware register in the RCU + register range +- resets : list of resets of the embedded GPHY +- reset-names : list of names of the resets + +Example: + +Ethernet switch on the VRX200 SoC: + +switch@e108000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-gswip"; + reg = < 0xe108000 0x3100 /* switch */ + 0xe10b100 0xd8 /* mdio */ + 0xe10b1d8 0x130 /* mii */ + >; + dsa,member = <0 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan3"; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + }; + + port@1 { + reg = <1>; + label = "lan4"; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + }; + + port@2 { + reg = <2>; + label = "lan2"; + phy-mode = "internal"; + phy-handle = <&phy11>; + }; + + port@4 { + reg = <4>; + label = "lan1"; + phy-mode = "internal"; + phy-handle = <&phy13>; + }; + + port@5 { + reg = <5>; + label = "wan"; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + }; + + port@6 { + reg = <0x6>; + label = "cpu"; + ethernet = <ð0>; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-mdio"; + reg = <0>; + + phy0: ethernet-phy@0 { + reg = <0x0>; + }; + phy1: ethernet-phy@1 { + reg = <0x1>; + }; + phy5: ethernet-phy@5 { + reg = <0x5>; + }; + phy11: ethernet-phy@11 { + reg = <0x11>; + }; + phy13: ethernet-phy@13 { + reg = <0x13>; + }; + }; + + gphy-fw { + compatible = "lantiq,xrx200-gphy-fw", "lantiq,gphy-fw"; + lantiq,rcu = <&rcu0>; + #address-cells = <1>; + #size-cells = <0>; + + gphy@20 { + reg = <0x20>; + + resets = <&reset0 31 30>; + reset-names = "gphy"; + }; + + gphy@68 { + reg = <0x68>; + + resets = <&reset0 29 28>; + reset-names = "gphy"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/lantiq,xrx200-net.txt b/Documentation/devicetree/bindings/net/lantiq,xrx200-net.txt new file mode 100644 index 000000000000..5ff5e68bbbb6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/lantiq,xrx200-net.txt @@ -0,0 +1,21 @@ +Lantiq xRX200 GSWIP PMAC Ethernet driver +================================== + +Required properties: + +- compatible : "lantiq,xrx200-net" for the PMAC of the embedded + : GSWIP in the xXR200 +- reg : memory range of the PMAC core inside of the GSWIP core +- interrupts : TX and RX DMA interrupts. Use interrupt-names "tx" for + : the TX interrupt and "rx" for the RX interrupt. + +Example: + +ethernet@e10b308 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-net"; + reg = <0xe10b308 0xcf8>; + interrupts = <73>, <72>; + interrupt-names = "tx", "rx"; +}; diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index 457d5ae16f23..3e17ac1d5d58 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -10,6 +10,7 @@ Required properties: Use "cdns,pc302-gem" for Picochip picoXcell pc302 and later devices based on the Cadence GEM, or the generic form: "cdns,gem". Use "atmel,sama5d2-gem" for the GEM IP (10/100) available on Atmel sama5d2 SoCs. + Use "atmel,sama5d3-macb" for the 10/100Mbit IP available on Atmel sama5d3 SoCs. Use "atmel,sama5d3-gem" for the Gigabit IP available on Atmel sama5d3 SoCs. Use "atmel,sama5d4-gem" for the GEM IP (10/100) available on Atmel sama5d4 SoCs. Use "cdns,zynq-gem" Xilinx Zynq-7xxx SoC. diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt index fc019df0d863..b78397669320 100644 --- a/Documentation/devicetree/bindings/net/marvell-pp2.txt +++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt @@ -31,7 +31,7 @@ required. Required properties (port): -- interrupts: interrupt for the port +- interrupts: interrupt(s) for the port - port-id: ID of the port from the MAC point of view - gop-port-id: only for marvell,armada-7k-pp2, ID of the port from the GOP (Group Of Ports) point of view. This ID is used to index the @@ -43,10 +43,12 @@ Optional properties (port): - marvell,loopback: port is loopback mode - phy: a phandle to a phy node defining the PHY address (as the reg property, a single integer). -- interrupt-names: if more than a single interrupt for rx is given, must - be the name associated to the interrupts listed. Valid - names are: "tx-cpu0", "tx-cpu1", "tx-cpu2", "tx-cpu3", - "rx-shared", "link". +- interrupt-names: if more than a single interrupt for is given, must be the + name associated to the interrupts listed. Valid names are: + "hifX", with X in [0..8], and "link". The names "tx-cpu0", + "tx-cpu1", "tx-cpu2", "tx-cpu3" and "rx-shared" are supported + for backward compatibility but shouldn't be used for new + additions. - marvell,system-controller: a phandle to the system controller. Example for marvell,armada-375-pp2: @@ -89,9 +91,14 @@ cpm_ethernet: ethernet@0 { <ICU_GRP_NSR 43 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 47 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 51 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 55 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2", - "tx-cpu3", "rx-shared"; + <ICU_GRP_NSR 55 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 59 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 63 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 67 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 71 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 129 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hif0", "hif1", "hif2", "hif3", "hif4", + "hif5", "hif6", "hif7", "hif8", "link"; port-id = <0>; gop-port-id = <0>; }; @@ -101,9 +108,14 @@ cpm_ethernet: ethernet@0 { <ICU_GRP_NSR 44 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 48 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 52 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 56 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2", - "tx-cpu3", "rx-shared"; + <ICU_GRP_NSR 56 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 60 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 64 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 68 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 72 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 128 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hif0", "hif1", "hif2", "hif3", "hif4", + "hif5", "hif6", "hif7", "hif8", "link"; port-id = <1>; gop-port-id = <2>; }; @@ -113,9 +125,14 @@ cpm_ethernet: ethernet@0 { <ICU_GRP_NSR 45 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 49 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 53 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 57 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2", - "tx-cpu3", "rx-shared"; + <ICU_GRP_NSR 57 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 61 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 65 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 69 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 73 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 127 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hif0", "hif1", "hif2", "hif3", "hif4", + "hif5", "hif6", "hif7", "hif8", "link"; port-id = <2>; gop-port-id = <3>; }; diff --git a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt index e22d8cfea687..5100358177c9 100644 --- a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt +++ b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt @@ -1,4 +1,4 @@ -Micrel KSZ9021/KSZ9031 Gigabit Ethernet PHY +Micrel KSZ9021/KSZ9031/KSZ9131 Gigabit Ethernet PHY Some boards require special tuning values, particularly when it comes to clock delays. You can specify clock delay values in the PHY OF @@ -64,6 +64,32 @@ KSZ9031: Attention: The link partner must be configurable as slave otherwise no link will be established. +KSZ9131: + + All skew control options are specified in picoseconds. The increment + step is 100ps. Unlike KSZ9031, the values represent picoseccond delays. + A negative value can be assigned as rxc-skew-psec = <(-100)>;. + + Optional properties: + + Range of the value -700 to 2400, default value 0: + + - rxc-skew-psec : Skew control of RX clock pad + - txc-skew-psec : Skew control of TX clock pad + + Range of the value -700 to 800, default value 0: + + - rxdv-skew-psec : Skew control of RX CTL pad + - txen-skew-psec : Skew control of TX CTL pad + - rxd0-skew-psec : Skew control of RX data 0 pad + - rxd1-skew-psec : Skew control of RX data 1 pad + - rxd2-skew-psec : Skew control of RX data 2 pad + - rxd3-skew-psec : Skew control of RX data 3 pad + - txd0-skew-psec : Skew control of TX data 0 pad + - txd1-skew-psec : Skew control of TX data 1 pad + - txd2-skew-psec : Skew control of TX data 2 pad + - txd3-skew-psec : Skew control of TX data 3 pad + Examples: mdio { diff --git a/Documentation/devicetree/bindings/net/mscc-ocelot.txt b/Documentation/devicetree/bindings/net/mscc-ocelot.txt index 0a84711abece..9e5c17d426ce 100644 --- a/Documentation/devicetree/bindings/net/mscc-ocelot.txt +++ b/Documentation/devicetree/bindings/net/mscc-ocelot.txt @@ -12,7 +12,6 @@ Required properties: - "sys" - "rew" - "qs" - - "hsio" - "qsys" - "ana" - "portX" with X from 0 to the number of last port index available on that @@ -45,7 +44,6 @@ Example: reg = <0x1010000 0x10000>, <0x1030000 0x10000>, <0x1080000 0x100>, - <0x10d0000 0x10000>, <0x11e0000 0x100>, <0x11f0000 0x100>, <0x1200000 0x100>, @@ -59,10 +57,9 @@ Example: <0x1280000 0x100>, <0x1800000 0x80000>, <0x1880000 0x10000>; - reg-names = "sys", "rew", "qs", "hsio", "port0", - "port1", "port2", "port3", "port4", "port5", - "port6", "port7", "port8", "port9", "port10", - "qsys", "ana"; + reg-names = "sys", "rew", "qs", "port0", "port1", "port2", + "port3", "port4", "port5", "port6", "port7", + "port8", "port9", "port10", "qsys", "ana"; interrupts = <21 22>; interrupt-names = "xtr", "inj"; diff --git a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt index 0eedabe22cc3..5ff37c68c941 100644 --- a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt +++ b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt @@ -1,10 +1,5 @@ * Microsemi - vsc8531 Giga bit ethernet phy -Required properties: -- compatible : Should contain phy id as "ethernet-phy-idAAAA.BBBB" - The PHY device uses the binding described in - Documentation/devicetree/bindings/net/phy.txt - Optional properties: - vsc8531,vddmac : The vddmac in mV. Allowed values is listed in the first row of Table 1 (below). @@ -27,14 +22,16 @@ Optional properties: 'vddmac'. Default value is 0%. Ref: Table:1 - Edge rate change (below). -- vsc8531,led-0-mode : LED mode. Specify how the LED[0] should behave. - Allowed values are define in - "include/dt-bindings/net/mscc-phy-vsc8531.h". - Default value is VSC8531_LINK_1000_ACTIVITY (1). -- vsc8531,led-1-mode : LED mode. Specify how the LED[1] should behave. - Allowed values are define in +- vsc8531,led-[N]-mode : LED mode. Specify how the LED[N] should behave. + N depends on the number of LEDs supported by a + PHY. + Allowed values are defined in "include/dt-bindings/net/mscc-phy-vsc8531.h". - Default value is VSC8531_LINK_100_ACTIVITY (2). + Default values are VSC8531_LINK_1000_ACTIVITY (1), + VSC8531_LINK_100_ACTIVITY (2), + VSC8531_LINK_ACTIVITY (0) and + VSC8531_DUPLEX_COLLISION (8). + Table: 1 - Edge rate change ----------------------------------------------------------------| diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt index da249b7c406c..3530256a879c 100644 --- a/Documentation/devicetree/bindings/net/renesas,ravb.txt +++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt @@ -6,6 +6,7 @@ interface contains. Required properties: - compatible: Must contain one or more of the following: - "renesas,etheravb-r8a7743" for the R8A7743 SoC. + - "renesas,etheravb-r8a7744" for the R8A7744 SoC. - "renesas,etheravb-r8a7745" for the R8A7745 SoC. - "renesas,etheravb-r8a77470" for the R8A77470 SoC. - "renesas,etheravb-r8a7790" for the R8A7790 SoC. diff --git a/Documentation/devicetree/bindings/net/sh_eth.txt b/Documentation/devicetree/bindings/net/sh_eth.txt index 76db9f13ad96..abc36274227c 100644 --- a/Documentation/devicetree/bindings/net/sh_eth.txt +++ b/Documentation/devicetree/bindings/net/sh_eth.txt @@ -16,6 +16,7 @@ Required properties: "renesas,ether-r8a7794" if the device is a part of R8A7794 SoC. "renesas,gether-r8a77980" if the device is a part of R8A77980 SoC. "renesas,ether-r7s72100" if the device is a part of R7S72100 SoC. + "renesas,ether-r7s9210" if the device is a part of R7S9210 SoC. "renesas,rcar-gen1-ether" for a generic R-Car Gen1 device. "renesas,rcar-gen2-ether" for a generic R-Car Gen2 or RZ/G1 device. diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt index 7fd4e8ce4149..2196d1ab3c8c 100644 --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt @@ -56,6 +56,11 @@ Optional properties: the length can vary between hw versions. - <supply-name>-supply: handle to the regulator device tree node optional "supply-name" is "vdd-0.8-cx-mx". +- memory-region: + Usage: optional + Value type: <phandle> + Definition: reference to the reserved-memory for the msa region + used by the wifi firmware running in Q6. Example (to supply the calibration data alone): @@ -149,4 +154,5 @@ wifi@18000000 { <0 140 0 /* CE10 */ >, <0 141 0 /* CE11 */ >; vdd-0.8-cx-mx-supply = <&pm8998_l5>; + memory-region = <&wifi_msa_mem>; }; diff --git a/Documentation/devicetree/bindings/phy/phy-ocelot-serdes.txt b/Documentation/devicetree/bindings/phy/phy-ocelot-serdes.txt new file mode 100644 index 000000000000..332219860187 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-ocelot-serdes.txt @@ -0,0 +1,43 @@ +Microsemi Ocelot SerDes muxing driver +------------------------------------- + +On Microsemi Ocelot, there is a handful of registers in HSIO address +space for setting up the SerDes to switch port muxing. + +A SerDes X can be "muxed" to work with switch port Y or Z for example. +One specific SerDes can also be used as a PCIe interface. + +Hence, a SerDes represents an interface, be it an Ethernet or a PCIe one. + +There are two kinds of SerDes: SERDES1G supports 10/100Mbps in +half/full-duplex and 1000Mbps in full-duplex mode while SERDES6G supports +10/100Mbps in half/full-duplex and 1000/2500Mbps in full-duplex mode. + +Also, SERDES6G number (aka "macro") 0 is the only interface supporting +QSGMII. + +This is a child of the HSIO syscon ("mscc,ocelot-hsio", see +Documentation/devicetree/bindings/mips/mscc.txt) on the Microsemi Ocelot. + +Required properties: + +- compatible: should be "mscc,vsc7514-serdes" +- #phy-cells : from the generic phy bindings, must be 2. + The first number defines the input port to use for a given + SerDes macro. The second defines the macro to use. They are + defined in dt-bindings/phy/phy-ocelot-serdes.h + +Example: + + serdes: serdes { + compatible = "mscc,vsc7514-serdes"; + #phy-cells = <2>; + }; + + ethernet { + port1 { + phy-handle = <&phy_foo>; + /* Link SERDES1G_5 to port1 */ + phys = <&serdes 1 SERDES1G_5>; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm4708-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/brcm,bcm4708-pinmux.txt new file mode 100644 index 000000000000..4fa9539070cb --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm4708-pinmux.txt @@ -0,0 +1,57 @@ +Broadcom Northstar pins mux controller + +Some of Northstar SoCs's pins can be used for various purposes thanks to the mux +controller. This binding allows describing mux controller and listing available +functions. They can be referenced later by other bindings to let system +configure controller correctly. + +A list of pins varies across chipsets so few bindings are available. + +Required properties: +- compatible: must be one of: + "brcm,bcm4708-pinmux" + "brcm,bcm4709-pinmux" + "brcm,bcm53012-pinmux" +- reg: iomem address range of CRU (Central Resource Unit) pin registers +- reg-names: "cru_gpio_control" - the only needed & supported reg right now + +Functions and their groups available for all chipsets: +- "spi": "spi_grp" +- "i2c": "i2c_grp" +- "pwm": "pwm0_grp", "pwm1_grp", "pwm2_grp", "pwm3_grp" +- "uart1": "uart1_grp" + +Additionally available on BCM4709 and BCM53012: +- "mdio": "mdio_grp" +- "uart2": "uart2_grp" +- "sdio": "sdio_pwr_grp", "sdio_1p8v_grp" + +For documentation of subnodes see: +Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +Example: + dmu@1800c000 { + compatible = "simple-bus"; + ranges = <0 0x1800c000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + cru@100 { + compatible = "simple-bus"; + reg = <0x100 0x1a4>; + ranges; + #address-cells = <1>; + #size-cells = <1>; + + pin-controller@1c0 { + compatible = "brcm,bcm4708-pinmux"; + reg = <0x1c0 0x24>; + reg-names = "cru_gpio_control"; + + spi-pins { + function = "spi"; + groups = "spi_grp"; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt index ca313a7aeaff..af20b0ec715c 100644 --- a/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt @@ -20,16 +20,30 @@ Required properties: - compatible: One of: - "ingenic,jz4740-pinctrl" + - "ingenic,jz4725b-pinctrl" - "ingenic,jz4770-pinctrl" - "ingenic,jz4780-pinctrl" - reg: Address range of the pinctrl registers. -GPIO sub-nodes --------------- +Required properties for sub-nodes (GPIO chips): +----------------------------------------------- -The pinctrl node can have optional sub-nodes for the Ingenic GPIO driver; -please refer to ../gpio/ingenic,gpio.txt. + - compatible: Must contain one of: + - "ingenic,jz4740-gpio" + - "ingenic,jz4770-gpio" + - "ingenic,jz4780-gpio" + - reg: The GPIO bank number. + - interrupt-controller: Marks the device node as an interrupt controller. + - interrupts: Interrupt specifier for the controllers interrupt. + - #interrupt-cells: Should be 2. Refer to + ../interrupt-controller/interrupts.txt for more details. + - gpio-controller: Marks the device node as a GPIO controller. + - #gpio-cells: Should be 2. The first cell is the GPIO number and the second + cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the + GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. + - gpio-ranges: Range of pins managed by the GPIO controller. Refer to + ../gpio/gpio.txt for more details. Example: @@ -38,4 +52,21 @@ Example: pinctrl: pin-controller@10010000 { compatible = "ingenic,jz4740-pinctrl"; reg = <0x10010000 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + gpa: gpio@0 { + compatible = "ingenic,jz4740-gpio"; + reg = <0>; + + gpio-controller; + gpio-ranges = <&pinctrl 0 0 32>; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + + interrupt-parent = <&intc>; + interrupts = <28>; + }; }; diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt index 54ecb8ab7788..82ead40311f6 100644 --- a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt @@ -13,6 +13,8 @@ Required properties for the root node: "amlogic,meson-gxl-aobus-pinctrl" "amlogic,meson-axg-periphs-pinctrl" "amlogic,meson-axg-aobus-pinctrl" + "amlogic,meson-g12a-periphs-pinctrl" + "amlogic,meson-g12a-aobus-pinctrl" - reg: address and size of registers controlling irq functionality === GPIO sub-nodes === diff --git a/Documentation/devicetree/bindings/pinctrl/nuvoton,npcm7xx-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/nuvoton,npcm7xx-pinctrl.txt new file mode 100644 index 000000000000..83f4bbac94bb --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/nuvoton,npcm7xx-pinctrl.txt @@ -0,0 +1,216 @@ +Nuvoton NPCM7XX Pin Controllers + +The Nuvoton BMC NPCM7XX Pin Controller multi-function routed through +the multiplexing block, Each pin supports GPIO functionality (GPIOx) +and multiple functions that directly connect the pin to different +hardware blocks. + +Required properties: +- #address-cells : should be 1. +- #size-cells : should be 1. +- compatible : "nuvoton,npcm750-pinctrl" for Poleg NPCM7XX. +- ranges : defines mapping ranges between pin controller node (parent) + to GPIO bank node (children). + +=== GPIO Bank Subnode === + +The NPCM7XX has 8 GPIO Banks each GPIO bank supports 32 GPIO. + +Required GPIO Bank subnode-properties: +- reg : specifies physical base address and size of the GPIO + bank registers. +- gpio-controller : Marks the device node as a GPIO controller. +- #gpio-cells : Must be <2>. The first cell is the gpio pin number + and the second cell is used for optional parameters. +- interrupts : contain the GPIO bank interrupt with flags for falling edge. +- gpio-ranges : defines the range of pins managed by the GPIO bank controller. + +For example, GPIO bank subnodes like the following: + gpio0: gpio@f0010000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x0 0x80>; + interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&pinctrl 0 0 32>; + }; + +=== Pin Mux Subnode === + +- pin: A string containing the name of the pin + An array of strings, each string containing the name of a pin. + These pin are used for selecting pin configuration. + +The following are the list of pins available: + "GPIO0/IOX1DI", "GPIO1/IOX1LD", "GPIO2/IOX1CK", "GPIO3/IOX1D0", + "GPIO4/IOX2DI/SMB1DSDA", "GPIO5/IOX2LD/SMB1DSCL", "GPIO6/IOX2CK/SMB2DSDA", + "GPIO7/IOX2D0/SMB2DSCL", "GPIO8/LKGPO1", "GPIO9/LKGPO2", "GPIO10/IOXHLD", + "GPIO11/IOXHCK", "GPIO12/GSPICK/SMB5BSCL", "GPIO13/GSPIDO/SMB5BSDA", + "GPIO14/GSPIDI/SMB5CSCL", "GPIO15/GSPICS/SMB5CSDA", "GPIO16/LKGPO0", + "GPIO17/PSPI2DI/SMB4DEN","GPIO18/PSPI2D0/SMB4BSDA", "GPIO19/PSPI2CK/SMB4BSCL", + "GPIO20/SMB4CSDA/SMB15SDA", "GPIO21/SMB4CSCL/SMB15SCL", "GPIO22/SMB4DSDA/SMB14SDA", + "GPIO23/SMB4DSCL/SMB14SCL", "GPIO24/IOXHDO", "GPIO25/IOXHDI", "GPIO26/SMB5SDA", + "GPIO27/SMB5SCL", "GPIO28/SMB4SDA", "GPIO29/SMB4SCL", "GPIO30/SMB3SDA", + "GPIO31/SMB3SCL", "GPIO32/nSPI0CS1","SPI0D2", "SPI0D3", "GPIO37/SMB3CSDA", + "GPIO38/SMB3CSCL", "GPIO39/SMB3BSDA", "GPIO40/SMB3BSCL", "GPIO41/BSPRXD", + "GPO42/BSPTXD/STRAP11", "GPIO43/RXD1/JTMS2/BU1RXD", "GPIO44/nCTS1/JTDI2/BU1CTS", + "GPIO45/nDCD1/JTDO2", "GPIO46/nDSR1/JTCK2", "GPIO47/nRI1/JCP_RDY2", + "GPIO48/TXD2/BSPTXD", "GPIO49/RXD2/BSPRXD", "GPIO50/nCTS2", "GPO51/nRTS2/STRAP2", + "GPIO52/nDCD2", "GPO53/nDTR2_BOUT2/STRAP1", "GPIO54/nDSR2", "GPIO55/nRI2", + "GPIO56/R1RXERR", "GPIO57/R1MDC", "GPIO58/R1MDIO", "GPIO59/SMB3DSDA", + "GPIO60/SMB3DSCL", "GPO61/nDTR1_BOUT1/STRAP6", "GPO62/nRTST1/STRAP5", + "GPO63/TXD1/STRAP4", "GPIO64/FANIN0", "GPIO65/FANIN1", "GPIO66/FANIN2", + "GPIO67/FANIN3", "GPIO68/FANIN4", "GPIO69/FANIN5", "GPIO70/FANIN6", "GPIO71/FANIN7", + "GPIO72/FANIN8", "GPIO73/FANIN9", "GPIO74/FANIN10", "GPIO75/FANIN11", + "GPIO76/FANIN12", "GPIO77/FANIN13","GPIO78/FANIN14", "GPIO79/FANIN15", + "GPIO80/PWM0", "GPIO81/PWM1", "GPIO82/PWM2", "GPIO83/PWM3", "GPIO84/R2TXD0", + "GPIO85/R2TXD1", "GPIO86/R2TXEN", "GPIO87/R2RXD0", "GPIO88/R2RXD1", "GPIO89/R2CRSDV", + "GPIO90/R2RXERR", "GPIO91/R2MDC", "GPIO92/R2MDIO", "GPIO93/GA20/SMB5DSCL", + "GPIO94/nKBRST/SMB5DSDA", "GPIO95/nLRESET/nESPIRST", "GPIO96/RG1TXD0", + "GPIO97/RG1TXD1", "GPIO98/RG1TXD2", "GPIO99/RG1TXD3","GPIO100/RG1TXC", + "GPIO101/RG1TXCTL", "GPIO102/RG1RXD0", "GPIO103/RG1RXD1", "GPIO104/RG1RXD2", + "GPIO105/RG1RXD3", "GPIO106/RG1RXC", "GPIO107/RG1RXCTL", "GPIO108/RG1MDC", + "GPIO109/RG1MDIO", "GPIO110/RG2TXD0/DDRV0", "GPIO111/RG2TXD1/DDRV1", + "GPIO112/RG2TXD2/DDRV2", "GPIO113/RG2TXD3/DDRV3", "GPIO114/SMB0SCL", + "GPIO115/SMB0SDA", "GPIO116/SMB1SCL", "GPIO117/SMB1SDA", "GPIO118/SMB2SCL", + "GPIO119/SMB2SDA", "GPIO120/SMB2CSDA", "GPIO121/SMB2CSCL", "GPIO122/SMB2BSDA", + "GPIO123/SMB2BSCL", "GPIO124/SMB1CSDA", "GPIO125/SMB1CSCL","GPIO126/SMB1BSDA", + "GPIO127/SMB1BSCL", "GPIO128/SMB8SCL", "GPIO129/SMB8SDA", "GPIO130/SMB9SCL", + "GPIO131/SMB9SDA", "GPIO132/SMB10SCL", "GPIO133/SMB10SDA","GPIO134/SMB11SCL", + "GPIO135/SMB11SDA", "GPIO136/SD1DT0", "GPIO137/SD1DT1", "GPIO138/SD1DT2", + "GPIO139/SD1DT3", "GPIO140/SD1CLK", "GPIO141/SD1WP", "GPIO142/SD1CMD", + "GPIO143/SD1CD/SD1PWR", "GPIO144/PWM4", "GPIO145/PWM5", "GPIO146/PWM6", + "GPIO147/PWM7", "GPIO148/MMCDT4", "GPIO149/MMCDT5", "GPIO150/MMCDT6", + "GPIO151/MMCDT7", "GPIO152/MMCCLK", "GPIO153/MMCWP", "GPIO154/MMCCMD", + "GPIO155/nMMCCD/nMMCRST", "GPIO156/MMCDT0", "GPIO157/MMCDT1", "GPIO158/MMCDT2", + "GPIO159/MMCDT3", "GPIO160/CLKOUT/RNGOSCOUT", "GPIO161/nLFRAME/nESPICS", + "GPIO162/SERIRQ", "GPIO163/LCLK/ESPICLK", "GPIO164/LAD0/ESPI_IO0", + "GPIO165/LAD1/ESPI_IO1", "GPIO166/LAD2/ESPI_IO2", "GPIO167/LAD3/ESPI_IO3", + "GPIO168/nCLKRUN/nESPIALERT", "GPIO169/nSCIPME", "GPIO170/nSMI", "GPIO171/SMB6SCL", + "GPIO172/SMB6SDA", "GPIO173/SMB7SCL", "GPIO174/SMB7SDA", "GPIO175/PSPI1CK/FANIN19", + "GPIO176/PSPI1DO/FANIN18", "GPIO177/PSPI1DI/FANIN17", "GPIO178/R1TXD0", + "GPIO179/R1TXD1", "GPIO180/R1TXEN", "GPIO181/R1RXD0", "GPIO182/R1RXD1", + "GPIO183/SPI3CK", "GPO184/SPI3D0/STRAP9", "GPO185/SPI3D1/STRAP10", + "GPIO186/nSPI3CS0", "GPIO187/nSPI3CS1", "GPIO188/SPI3D2/nSPI3CS2", + "GPIO189/SPI3D3/nSPI3CS3", "GPIO190/nPRD_SMI", "GPIO191", "GPIO192", "GPIO193/R1CRSDV", + "GPIO194/SMB0BSCL", "GPIO195/SMB0BSDA", "GPIO196/SMB0CSCL", "GPIO197/SMB0DEN", + "GPIO198/SMB0DSDA", "GPIO199/SMB0DSCL", "GPIO200/R2CK", "GPIO201/R1CK", + "GPIO202/SMB0CSDA", "GPIO203/FANIN16", "GPIO204/DDC2SCL", "GPIO205/DDC2SDA", + "GPIO206/HSYNC2", "GPIO207/VSYNC2", "GPIO208/RG2TXC/DVCK", "GPIO209/RG2TXCTL/DDRV4", + "GPIO210/RG2RXD0/DDRV5", "GPIO211/RG2RXD1/DDRV6", "GPIO212/RG2RXD2/DDRV7", + "GPIO213/RG2RXD3/DDRV8", "GPIO214/RG2RXC/DDRV9", "GPIO215/RG2RXCTL/DDRV10", + "GPIO216/RG2MDC/DDRV11", "GPIO217/RG2MDIO/DVHSYNC", "GPIO218/nWDO1", + "GPIO219/nWDO2", "GPIO220/SMB12SCL", "GPIO221/SMB12SDA", "GPIO222/SMB13SCL", + "GPIO223/SMB13SDA", "GPIO224/SPIXCK", "GPO225/SPIXD0/STRAP12", "GPO226/SPIXD1/STRAP13", + "GPIO227/nSPIXCS0", "GPIO228/nSPIXCS1", "GPO229/SPIXD2/STRAP3", "GPIO230/SPIXD3", + "GPIO231/nCLKREQ", "GPI255/DACOSEL" + +Optional Properties: + bias-disable, bias-pull-down, bias-pull-up, input-enable, + input-disable, output-high, output-low, drive-push-pull, + drive-open-drain, input-debounce, slew-rate, drive-strength + + slew-rate valid arguments are: + <0> - slow + <1> - fast + drive-strength valid arguments are: + <2> - 2mA + <4> - 4mA + <8> - 8mA + <12> - 12mA + <16> - 16mA + <24> - 24mA + +For example, pinctrl might have pinmux subnodes like the following: + + gpio0_iox1d1_pin: gpio0-iox1d1-pin { + pins = "GPIO0/IOX1DI"; + output-high; + }; + gpio0_iox1ck_pin: gpio0-iox1ck-pin { + pins = "GPIO2/IOX1CK"; + output_high; + }; + +=== Pin Group Subnode === + +Required pin group subnode-properties: +- groups : A string containing the name of the group to mux. +- function: A string containing the name of the function to mux to the + group. + +The following are the list of the available groups and functions : + smb0, smb0b, smb0c, smb0d, smb0den, smb1, smb1b, smb1c, smb1d, + smb2, smb2b, smb2c, smb2d, smb3, smb3b, smb3c, smb3d, smb4, smb4b, + smb4c, smb4d, smb4den, smb5, smb5b, smb5c, smb5d, ga20kbc, smb6, + smb7, smb8, smb9, smb10, smb11, smb12, smb13, smb14, smb15, fanin0, + fanin1, fanin2, fanin3, fanin4, fanin5, fanin6, fanin7, fanin8, + fanin9, fanin10, fanin11 fanin12 fanin13, fanin14, fanin15, faninx, + pwm0, pwm1, pwm2, pwm3, pwm4, pwm5, pwm6, pwm7, rg1, rg1mdio, rg2, + rg2mdio, ddr, uart1, uart2, bmcuart0a, bmcuart0b, bmcuart1, iox1, + iox2, ioxh, gspi, mmc, mmcwp, mmccd, mmcrst, mmc8, r1, r1err, r1md, + r2, r2err, r2md, sd1, sd1pwr, wdog1, wdog2, scipme, sci, serirq, + jtag2, spix, spixcs1, pspi1, pspi2, ddc, clkreq, clkout, spi3, spi3cs1, + spi3quad, spi3cs2, spi3cs3, spi0cs1, lpc, lpcclk, espi, lkgpo0, lkgpo1, + lkgpo2, nprd_smi + +For example, pinctrl might have group subnodes like the following: + r1err_pins: r1err-pins { + groups = "r1err"; + function = "r1err"; + }; + r1md_pins: r1md-pins { + groups = "r1md"; + function = "r1md"; + }; + r1_pins: r1-pins { + groups = "r1"; + function = "r1"; + }; + +Examples +======== +pinctrl: pinctrl@f0800000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "nuvoton,npcm750-pinctrl"; + ranges = <0 0xf0010000 0x8000>; + + gpio0: gpio@f0010000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x0 0x80>; + interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&pinctrl 0 0 32>; + }; + + .... + + gpio7: gpio@f0017000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x7000 0x80>; + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&pinctrl 0 224 32>; + }; + + gpio0_iox1d1_pin: gpio0-iox1d1-pin { + pins = "GPIO0/IOX1DI"; + output-high; + }; + + iox1_pins: iox1-pins { + groups = "iox1"; + function = "iox1"; + }; + iox2_pins: iox2-pins { + groups = "iox2"; + function = "iox2"; + }; + + .... + + clkreq_pins: clkreq-pins { + groups = "clkreq"; + function = "clkreq"; + }; +};
\ No newline at end of file diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt index ffd4345415f3..ab4000eab07d 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt @@ -19,6 +19,7 @@ PMIC's from Qualcomm. "qcom,pm8998-gpio" "qcom,pma8084-gpio" "qcom,pmi8994-gpio" + "qcom,pms405-gpio" And must contain either "qcom,spmi-gpio" or "qcom,ssbi-gpio" if the device is on an spmi bus or an ssbi bus respectively @@ -91,6 +92,7 @@ to specify in a pin configuration subnode: gpio1-gpio26 for pm8998 gpio1-gpio22 for pma8084 gpio1-gpio10 for pmi8994 + gpio1-gpio11 for pms405 - function: Usage: required diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.txt new file mode 100644 index 000000000000..2b8f77762edc --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.txt @@ -0,0 +1,199 @@ +Qualcomm QCS404 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +QCS404 platform. + +- compatible: + Usage: required + Value type: <string> + Definition: must be "qcom,qcs404-pinctrl" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the north, south and east TLMM + tiles. + +- reg-names: + Usage: required + Value type: <stringlist> + Defintiion: names for the cells of reg, must contain "north", "south" + and "east". + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: <none> + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/interrupt-controller/irq.h> + +- gpio-controller: + Usage: required + Value type: <none> + Definition: identifies this node as a gpio controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/gpio/gpio.h> + +- gpio-ranges: + Usage: required + Definition: see ../gpio/gpio.txt + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. + + Valid pins are: + gpio0-gpio119 + Supports mux, bias and drive-strength + + sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, + sdc2_data + Supports bias and drive-strength + + ufs_reset + Supports bias and drive-strength + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Functions are only valid for gpio pins. + Valid values are: + + gpio, hdmi_tx, hdmi_ddc, blsp_uart_tx_a2, blsp_spi2, m_voc, + qdss_cti_trig_in_a0, blsp_uart_rx_a2, qdss_tracectl_a, + blsp_uart2, aud_cdc, blsp_i2c_sda_a2, qdss_tracedata_a, + blsp_i2c_scl_a2, qdss_tracectl_b, qdss_cti_trig_in_b0, + blsp_uart1, blsp_spi_mosi_a1, blsp_spi_miso_a1, + qdss_tracedata_b, blsp_i2c1, blsp_spi_cs_n_a1, gcc_plltest, + blsp_spi_clk_a1, rgb_data0, blsp_uart5, blsp_spi5, + adsp_ext, rgb_data1, prng_rosc, rgb_data2, blsp_i2c5, + gcc_gp1_clk_b, rgb_data3, gcc_gp2_clk_b, blsp_spi0, + blsp_uart0, gcc_gp3_clk_b, blsp_i2c0, qdss_traceclk_b, + pcie_clk, nfc_irq, blsp_spi4, nfc_dwl, audio_ts, rgb_data4, + spi_lcd, blsp_uart_tx_b2, gcc_gp3_clk_a, rgb_data5, + blsp_uart_rx_b2, blsp_i2c_sda_b2, blsp_i2c_scl_b2, + pwm_led11, i2s_3_data0_a, ebi2_lcd, i2s_3_data1_a, + i2s_3_data2_a, atest_char, pwm_led3, i2s_3_data3_a, + pwm_led4, i2s_4, ebi2_a, dsd_clk_b, pwm_led5, pwm_led6, + pwm_led7, pwm_led8, pwm_led24, spkr_dac0, blsp_i2c4, + pwm_led9, pwm_led10, spdifrx_opt, pwm_led12, pwm_led13, + pwm_led14, wlan1_adc1, rgb_data_b0, pwm_led15, + blsp_spi_mosi_b1, wlan1_adc0, rgb_data_b1, pwm_led16, + blsp_spi_miso_b1, qdss_cti_trig_out_b0, wlan2_adc1, + rgb_data_b2, pwm_led17, blsp_spi_cs_n_b1, wlan2_adc0, + rgb_data_b3, pwm_led18, blsp_spi_clk_b1, rgb_data_b4, + pwm_led19, ext_mclk1_b, qdss_traceclk_a, rgb_data_b5, + pwm_led20, atest_char3, i2s_3_sck_b, ldo_update, bimc_dte0, + rgb_hsync, pwm_led21, i2s_3_ws_b, dbg_out, rgb_vsync, + i2s_3_data0_b, ldo_en, hdmi_dtest, rgb_de, i2s_3_data1_b, + hdmi_lbk9, rgb_clk, atest_char1, i2s_3_data2_b, ebi_cdc, + hdmi_lbk8, rgb_mdp, atest_char0, i2s_3_data3_b, hdmi_lbk7, + rgb_data_b6, rgb_data_b7, hdmi_lbk6, rgmii_int, cri_trng1, + rgmii_wol, cri_trng0, gcc_tlmm, rgmii_ck, rgmii_tx, + hdmi_lbk5, hdmi_pixel, hdmi_rcv, hdmi_lbk4, rgmii_ctl, + ext_lpass, rgmii_rx, cri_trng, hdmi_lbk3, hdmi_lbk2, + qdss_cti_trig_out_b1, rgmii_mdio, hdmi_lbk1, rgmii_mdc, + hdmi_lbk0, ir_in, wsa_en, rgb_data6, rgb_data7, + atest_char2, ebi_ch0, blsp_uart3, blsp_spi3, sd_write, + blsp_i2c3, gcc_gp1_clk_a, qdss_cti_trig_in_b1, + gcc_gp2_clk_a, ext_mclk0, mclk_in1, i2s_1, dsd_clk_a, + qdss_cti_trig_in_a1, rgmi_dll1, pwm_led22, pwm_led23, + qdss_cti_trig_out_a0, rgmi_dll2, pwm_led1, + qdss_cti_trig_out_a1, pwm_led2, i2s_2, pll_bist, + ext_mclk1_a, mclk_in2, bimc_dte1, i2s_3_sck_a, i2s_3_ws_a + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull down. + +- bias-pull-up: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull up. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + Not valid for sdc pins. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + Not valid for sdc pins. + +- drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + tlmm: pinctrl@1000000 { + compatible = "qcom,qcs404-pinctrl"; + reg = <0x01000000 0x200000>, + <0x01300000 0x200000>, + <0x07b00000 0x200000>; + reg-names = "south", "north", "east"; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 0 120>; + interrupt-controller; + #interrupt-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt new file mode 100644 index 000000000000..769ca83bb40d --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt @@ -0,0 +1,191 @@ +Qualcomm Technologies, Inc. SDM660 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +SDM660 platform. + +- compatible: + Usage: required + Value type: <string> + Definition: must be "qcom,sdm660-pinctrl" or + "qcom,sdm630-pinctrl". + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the north, center and south + TLMM tiles. + +- reg-names: + Usage: required + Value type: <stringlist> + Definition: names for the cells of reg, must contain "north", "center" + and "south". + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: <none> + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/interrupt-controller/irq.h> + +- gpio-controller: + Usage: required + Value type: <none> + Definition: identifies this node as a gpio controller + +- gpio-ranges: + Usage: required + Value type: <prop-encoded-array> + Definition: Specifies the mapping between gpio controller and + pin-controller pins. + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/gpio/gpio.h> + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. Valid pins are: + gpio0-gpio113, + Supports mux, bias and drive-strength + sdc1_clk, sdc1_cmd, sdc1_data sdc2_clk, sdc2_cmd, sdc2_data sdc1_rclk, + Supports bias and drive-strength + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Functions are only valid for gpio pins. + Valid values are: + adsp_ext, agera_pll, atest_char, atest_char0, atest_char1, + atest_char2, atest_char3, atest_gpsadc0, atest_gpsadc1, + atest_tsens, atest_tsens2, atest_usb1, atest_usb10, + atest_usb11, atest_usb12, atest_usb13, atest_usb2, + atest_usb20, atest_usb21, atest_usb22, atest_usb23, + audio_ref, bimc_dte0, bimc_dte1, blsp_i2c1, blsp_i2c2, + blsp_i2c3, blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_i2c7, + blsp_i2c8_a, blsp_i2c8_b, blsp_spi1, blsp_spi2, blsp_spi3, + blsp_spi3_cs1, blsp_spi3_cs2, blsp_spi4, blsp_spi5, + blsp_spi6, blsp_spi7, blsp_spi8_a, blsp_spi8_b, + blsp_spi8_cs1, blsp_spi8_cs2, blsp_uart1, blsp_uart2, + blsp_uart5, blsp_uart6_a, blsp_uart6_b, blsp_uim1, + blsp_uim2, blsp_uim5, blsp_uim6, cam_mclk, cci_async, + cci_i2c, cri_trng, cri_trng0, cri_trng1, dbg_out, ddr_bist, + gcc_gp1, gcc_gp2, gcc_gp3, gpio, gps_tx_a, gps_tx_b, gps_tx_c, + isense_dbg, jitter_bist, ldo_en, ldo_update, m_voc, mdp_vsync, + mdss_vsync0, mdss_vsync1, mdss_vsync2, mdss_vsync3, mss_lte, + nav_pps_a, nav_pps_b, nav_pps_c, pa_indicator, phase_flag0, + phase_flag1, phase_flag10, phase_flag11, phase_flag12, + phase_flag13, phase_flag14, phase_flag15, phase_flag16, + phase_flag17, phase_flag18, phase_flag19, phase_flag2, + phase_flag20, phase_flag21, phase_flag22, phase_flag23, + phase_flag24, phase_flag25, phase_flag26, phase_flag27, + phase_flag28, phase_flag29, phase_flag3, phase_flag30, + phase_flag31, phase_flag4, phase_flag5, phase_flag6, + phase_flag7, phase_flag8, phase_flag9, pll_bypassnl, + pll_reset, pri_mi2s, pri_mi2s_ws, prng_rosc, pwr_crypto, + pwr_modem, pwr_nav, qdss_cti0_a, qdss_cti0_b, qdss_cti1_a, + qdss_cti1_b, qdss_gpio, qdss_gpio0, qdss_gpio1, qdss_gpio10, + qdss_gpio11, qdss_gpio12, qdss_gpio13, qdss_gpio14, qdss_gpio15, + qdss_gpio2, qdss_gpio3, qdss_gpio4, qdss_gpio5, qdss_gpio6, + qdss_gpio7, qdss_gpio8, qdss_gpio9, qlink_enable, qlink_request, + qspi_clk, qspi_cs, qspi_data0, qspi_data1, qspi_data2, + qspi_data3, qspi_resetn, sec_mi2s, sndwire_clk, sndwire_data, + sp_cmu, ssc_irq, tgu_ch0, tgu_ch1, tsense_pwm1, tsense_pwm2, + uim1_clk, uim1_data, uim1_present, uim1_reset, uim2_clk, + uim2_data, uim2_present, uim2_reset, uim_batt, vfr_1, + vsense_clkout, vsense_data0, vsense_data1, vsense_mode, + wlan1_adc0, wlan1_adc1, wlan2_adc0, wlan2_adc1 + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull down. + +- bias-pull-up: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull up. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + Not valid for sdc pins. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + Not valid for sdc pins. + +- drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + tlmm: pinctrl@3100000 { + compatible = "qcom,sdm660-pinctrl"; + reg = <0x3100000 0x200000>, + <0x3500000 0x200000>, + <0x3900000 0x200000>; + reg-names = "south", "center", "north"; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + gpio-ranges = <&tlmm 0 0 114>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt index abd8fbcf1e62..3902efa18fd0 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -14,8 +14,11 @@ Required Properties: - "renesas,pfc-r8a73a4": for R8A73A4 (R-Mobile APE6) compatible pin-controller. - "renesas,pfc-r8a7740": for R8A7740 (R-Mobile A1) compatible pin-controller. - "renesas,pfc-r8a7743": for R8A7743 (RZ/G1M) compatible pin-controller. + - "renesas,pfc-r8a7744": for R8A7744 (RZ/G1N) compatible pin-controller. - "renesas,pfc-r8a7745": for R8A7745 (RZ/G1E) compatible pin-controller. - "renesas,pfc-r8a77470": for R8A77470 (RZ/G1C) compatible pin-controller. + - "renesas,pfc-r8a774a1": for R8A774A1 (RZ/G2M) compatible pin-controller. + - "renesas,pfc-r8a774c0": for R8A774C0 (RZ/G2E) compatible pin-controller. - "renesas,pfc-r8a7778": for R8A7778 (R-Car M1) compatible pin-controller. - "renesas,pfc-r8a7779": for R8A7779 (R-Car H1) compatible pin-controller. - "renesas,pfc-r8a7790": for R8A7790 (R-Car H2) compatible pin-controller. diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rzn1-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,rzn1-pinctrl.txt new file mode 100644 index 000000000000..25e53acd523e --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/renesas,rzn1-pinctrl.txt @@ -0,0 +1,153 @@ +Renesas RZ/N1 SoC Pinctrl node description. + +Pin controller node +------------------- +Required properties: +- compatible: SoC-specific compatible string "renesas,<soc-specific>-pinctrl" + followed by "renesas,rzn1-pinctrl" as fallback. The SoC-specific compatible + strings must be one of: + "renesas,r9a06g032-pinctrl" for RZ/N1D + "renesas,r9a06g033-pinctrl" for RZ/N1S +- reg: Address base and length of the memory area where the pin controller + hardware is mapped to. +- clocks: phandle for the clock, see the description of clock-names below. +- clock-names: Contains the name of the clock: + "bus", the bus clock, sometimes described as pclk, for register accesses. + +Example: + pinctrl: pin-controller@40067000 { + compatible = "renesas,r9a06g032-pinctrl", "renesas,rzn1-pinctrl"; + reg = <0x40067000 0x1000>, <0x51000000 0x480>; + clocks = <&sysctrl R9A06G032_HCLK_PINCONFIG>; + clock-names = "bus"; + }; + +Sub-nodes +--------- + +The child nodes of the pin controller node describe a pin multiplexing +function. + +- Pin multiplexing sub-nodes: + A pin multiplexing sub-node describes how to configure a set of + (or a single) pin in some desired alternate function mode. + A single sub-node may define several pin configurations. + Please refer to pinctrl-bindings.txt to get to know more on generic + pin properties usage. + + The allowed generic formats for a pin multiplexing sub-node are the + following ones: + + node-1 { + pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ; + GENERIC_PINCONFIG; + }; + + node-2 { + sub-node-1 { + pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ; + GENERIC_PINCONFIG; + }; + + sub-node-2 { + pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ; + GENERIC_PINCONFIG; + }; + + ... + + sub-node-n { + pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ; + GENERIC_PINCONFIG; + }; + }; + + node-3 { + pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ; + GENERIC_PINCONFIG; + + sub-node-1 { + pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ; + GENERIC_PINCONFIG; + }; + + ... + + sub-node-n { + pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ; + GENERIC_PINCONFIG; + }; + }; + + Use the latter two formats when pins part of the same logical group need to + have different generic pin configuration flags applied. Note that the generic + pinconfig in node-3 does not apply to the sub-nodes. + + Client sub-nodes shall refer to pin multiplexing sub-nodes using the phandle + of the most external one. + + Eg. + + client-1 { + ... + pinctrl-0 = <&node-1>; + ... + }; + + client-2 { + ... + pinctrl-0 = <&node-2>; + ... + }; + + Required properties: + - pinmux: + integer array representing pin number and pin multiplexing configuration. + When a pin has to be configured in alternate function mode, use this + property to identify the pin by its global index, and provide its + alternate function configuration number along with it. + When multiple pins are required to be configured as part of the same + alternate function they shall be specified as members of the same + argument list of a single "pinmux" property. + Integers values in the "pinmux" argument list are assembled as: + (PIN | MUX_FUNC << 8) + where PIN directly corresponds to the pl_gpio pin number and MUX_FUNC is + one of the alternate function identifiers defined in: + <include/dt-bindings/pinctrl/rzn1-pinctrl.h> + These identifiers collapse the IO Multiplex Configuration Level 1 and + Level 2 numbers that are detailed in the hardware reference manual into a + single number. The identifiers for Level 2 are simply offset by 10. + Additional identifiers are provided to specify the MDIO source peripheral. + + Optional generic pinconf properties: + - bias-disable - disable any pin bias + - bias-pull-up - pull up the pin with 50 KOhm + - bias-pull-down - pull down the pin with 50 KOhm + - bias-high-impedance - high impedance mode + - drive-strength - sink or source at most 4, 6, 8 or 12 mA + + Example: + A serial communication interface with a TX output pin and an RX input pin. + + &pinctrl { + pins_uart0: pins_uart0 { + pinmux = < + RZN1_PINMUX(103, RZN1_FUNC_UART0_I) /* UART0_TXD */ + RZN1_PINMUX(104, RZN1_FUNC_UART0_I) /* UART0_RXD */ + >; + }; + }; + + Example 2: + Here we set the pull up on the RXD pin of the UART. + + &pinctrl { + pins_uart0: pins_uart0 { + pinmux = <RZN1_PINMUX(103, RZN1_FUNC_UART0_I)>; /* TXD */ + + pins_uart6_rx { + pinmux = <RZN1_PINMUX(104, RZN1_FUNC_UART0_I)>; /* RXD */ + bias-pull-up; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/pfuze100.txt b/Documentation/devicetree/bindings/regulator/pfuze100.txt index c7610718adff..f9be1acf891c 100644 --- a/Documentation/devicetree/bindings/regulator/pfuze100.txt +++ b/Documentation/devicetree/bindings/regulator/pfuze100.txt @@ -12,6 +12,11 @@ Optional properties: disabled. This binding is a workaround to keep backward compatibility with old dtb's which rely on the fact that the switched regulators are always on and don't mark them explicit as "regulator-always-on". +- fsl,pmic-stby-poweroff: if present, configure the PMIC to shutdown all + power rails when PMIC_STBY_REQ line is asserted during the power off sequence. + Use this option if the SoC should be powered off by external power + management IC (PMIC) on PMIC_STBY_REQ signal. + As opposite to PMIC_STBY_REQ boards can implement PMIC_ON_REQ signal. Required child node: - regulators: This is the list of child nodes that specify the regulator diff --git a/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt index 58a1d97972f5..45025b5b67f6 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt @@ -26,6 +26,7 @@ Regulator nodes are identified by their compatible: "qcom,rpm-pm8998-regulators" "qcom,rpm-pma8084-regulators" "qcom,rpm-pmi8998-regulators" + "qcom,rpm-pms405-regulators" - vdd_s1-supply: - vdd_s2-supply: @@ -188,6 +189,24 @@ Regulator nodes are identified by their compatible: Definition: reference to regulator supplying the input pin, as described in the data sheet +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_s4-supply: +- vdd_s5-supply: +- vdd_l1_l2-supply: +- vdd_l3_l8-supply: +- vdd_l4-supply: +- vdd_l5_l6-supply: +- vdd_l7-supply: +- vdd_l3_l8-supply: +- vdd_l9-supply: +- vdd_l10_l11_l12_l13-supply: + Usage: optional (pms405 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + The regulator node houses sub-nodes for each regulator within the device. Each sub-node is identified using the node's name, with valid values listed for each of the pmics below. @@ -222,6 +241,10 @@ pma8084: pmi8998: bob +pms405: + s1, s2, s3, s4, s5, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, + l13 + The content of each sub-node is defined by the standard binding for regulators - see regulator.txt. diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt index 76ead07072b1..4b98ca26e61a 100644 --- a/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt @@ -1,7 +1,9 @@ -ROHM BD71837 Power Management Integrated Circuit (PMIC) regulator bindings +ROHM BD71837 and BD71847 Power Management Integrated Circuit regulator bindings Required properties: - - regulator-name: should be "buck1", ..., "buck8" and "ldo1", ..., "ldo7" + - regulator-name: should be "buck1", ..., "buck8" and "ldo1", ..., "ldo7" for + BD71837. For BD71847 names should be "buck1", ..., "buck6" + and "ldo1", ..., "ldo6" List of regulators provided by this controller. BD71837 regulators node should be sub node of the BD71837 MFD node. See BD71837 MFD bindings at @@ -16,10 +18,14 @@ disabled by driver at startup. LDO5 and LDO6 are supplied by those and if they are disabled at startup the voltage monitoring for LDO5/LDO6 will cause PMIC to reset. -The valid names for regulator nodes are: +The valid names for BD71837 regulator nodes are: BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6, BUCK7, BUCK8 LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7 +The valid names for BD71847 regulator nodes are: +BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6 +LDO1, LDO2, LDO3, LDO4, LDO5, LDO6 + Optional properties: - Any optional property defined in bindings/regulator/regulator.txt diff --git a/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt b/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt new file mode 100644 index 000000000000..a3f476240565 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt @@ -0,0 +1,68 @@ +STMicroelectronics STPMIC1 Voltage regulators + +Regulator Nodes are optional depending on needs. + +Available Regulators in STPMIC1 device are: + - buck1 for Buck BUCK1 + - buck2 for Buck BUCK2 + - buck3 for Buck BUCK3 + - buck4 for Buck BUCK4 + - ldo1 for LDO LDO1 + - ldo2 for LDO LDO2 + - ldo3 for LDO LDO3 + - ldo4 for LDO LDO4 + - ldo5 for LDO LDO5 + - ldo6 for LDO LDO6 + - vref_ddr for LDO Vref DDR + - boost for Buck BOOST + - pwr_sw1 for VBUS_OTG switch + - pwr_sw2 for SW_OUT switch + +Switches are fixed voltage regulators with only enable/disable capability. + +Optional properties: +- st,mask-reset: mask reset for this regulator: the regulator configuration + is maintained during pmic reset. +- regulator-pull-down: enable high pull down + if not specified light pull down is used +- regulator-over-current-protection: + if set, all regulators are switched off in case of over-current detection + on this regulator, + if not set, the driver only sends an over-current event. +- interrupt-parent: phandle to the parent interrupt controller +- interrupts: index of current limit detection interrupt +- <regulator>-supply: phandle to the parent supply/regulator node + each regulator supply can be described except vref_ddr. + +Example: +regulators { + compatible = "st,stpmic1-regulators"; + + ldo6-supply = <&v3v3>; + + vdd_core: buck1 { + regulator-name = "vdd_core"; + interrupts = <IT_CURLIM_BUCK1 0>; + interrupt-parent = <&pmic>; + st,mask-reset; + regulator-pull-down; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1200000>; + }; + + v3v3: buck4 { + regulator-name = "v3v3"; + interrupts = <IT_CURLIM_BUCK4 0>; + interrupt-parent = <&mypmic>; + + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + v1v8: ldo6 { + regulator-name = "v1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-over-current-protection; + }; +}; diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/network.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/network.txt index 03c741602c6d..6d2dd8a31482 100644 --- a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/network.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/network.txt @@ -98,6 +98,12 @@ The property below is dependent on fsl,tdm-interface: usage: optional for tdm interface value type: <empty> Definition : Internal loopback connecting on TDM layer. +- fsl,hmask + usage: optional + Value type: <u16> + Definition: HDLC address recognition. Set to zero to disable + address filtering of packets: + fsl,hmask = /bits/ 16 <0x0000>; Example for tdm interface: diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt index ff92e5a41bed..dab7ca9f250c 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt @@ -53,20 +53,8 @@ Required properties: - clocks: Serial engine core clock needed by the device. Qualcomm Technologies Inc. GENI Serial Engine based SPI Controller - -Required properties: -- compatible: Must contain "qcom,geni-spi". -- reg: Must contain SPI register location and length. -- interrupts: Must contain SPI controller interrupts. -- clock-names: Must contain "se". -- clocks: Serial engine core clock needed by the device. -- spi-max-frequency: Specifies maximum SPI clock frequency, units - Hz. -- #address-cells: Must be <1> to define a chip select address on - the SPI bus. -- #size-cells: Must be <0>. - -SPI slave nodes must be children of the SPI master node and conform to SPI bus -binding as described in Documentation/devicetree/bindings/spi/spi-bus.txt. +node binding is described in +Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt. Example: geniqup@8c0000 { @@ -103,17 +91,4 @@ Example: pinctrl-1 = <&qup_1_uart_3_sleep>; }; - spi0: spi@a84000 { - compatible = "qcom,geni-spi"; - reg = <0xa84000 0x4000>; - interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "se"; - clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&qup_1_spi_2_active>; - pinctrl-1 = <&qup_1_spi_2_sleep>; - spi-max-frequency = <19200000>; - #address-cells = <1>; - #size-cells = <0>; - }; } diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt b/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt new file mode 100644 index 000000000000..790311a42bf1 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt @@ -0,0 +1,39 @@ +GENI based Qualcomm Universal Peripheral (QUP) Serial Peripheral Interface (SPI) + +The QUP v3 core is a GENI based AHB slave that provides a common data path +(an output FIFO and an input FIFO) for serial peripheral interface (SPI) +mini-core. + +SPI in master mode supports up to 50MHz, up to four chip selects, programmable +data path from 4 bits to 32 bits and numerous protocol variants. + +Required properties: +- compatible: Must contain "qcom,geni-spi". +- reg: Must contain SPI register location and length. +- interrupts: Must contain SPI controller interrupts. +- clock-names: Must contain "se". +- clocks: Serial engine core clock needed by the device. +- #address-cells: Must be <1> to define a chip select address on + the SPI bus. +- #size-cells: Must be <0>. + +SPI Controller nodes must be child of GENI based Qualcomm Universal +Peripharal. Please refer GENI based QUP wrapper controller node bindings +described in Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt. + +SPI slave nodes must be children of the SPI master node and conform to SPI bus +binding as described in Documentation/devicetree/bindings/spi/spi-bus.txt. + +Example: + spi0: spi@a84000 { + compatible = "qcom,geni-spi"; + reg = <0xa84000 0x4000>; + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "se"; + clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&qup_1_spi_2_active>; + pinctrl-1 = <&qup_1_spi_2_sleep>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.txt b/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.txt new file mode 100644 index 000000000000..1d64b61f5171 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.txt @@ -0,0 +1,36 @@ +Qualcomm Quad Serial Peripheral Interface (QSPI) + +The QSPI controller allows SPI protocol communication in single, dual, or quad +wire transmission modes for read/write access to slaves such as NOR flash. + +Required properties: +- compatible: An SoC specific identifier followed by "qcom,qspi-v1", such as + "qcom,sdm845-qspi", "qcom,qspi-v1" +- reg: Should contain the base register location and length. +- interrupts: Interrupt number used by the controller. +- clocks: Should contain the core and AHB clock. +- clock-names: Should be "core" for core clock and "iface" for AHB clock. + +SPI slave nodes must be children of the SPI master node and can contain +properties described in Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + + qspi: spi@88df000 { + compatible = "qcom,sdm845-qspi", "qcom,qspi-v1"; + reg = <0x88df000 0x600>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "iface", "core"; + clocks = <&gcc GCC_QSPI_CNOC_PERIPH_AHB_CLK>, + <&gcc GCC_QSPI_CORE_CLK>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + spi-tx-bus-width = <2>; + spi-rx-bus-width = <2>; + }; + }; diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index bfbc2035fb6b..4b836ad17b19 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -2,7 +2,9 @@ Renesas MSIOF spi controller Required properties: - compatible : "renesas,msiof-r8a7743" (RZ/G1M) + "renesas,msiof-r8a7744" (RZ/G1N) "renesas,msiof-r8a7745" (RZ/G1E) + "renesas,msiof-r8a774a1" (RZ/G2M) "renesas,msiof-r8a7790" (R-Car H2) "renesas,msiof-r8a7791" (R-Car M2-W) "renesas,msiof-r8a7792" (R-Car V2H) @@ -11,10 +13,14 @@ Required properties: "renesas,msiof-r8a7795" (R-Car H3) "renesas,msiof-r8a7796" (R-Car M3-W) "renesas,msiof-r8a77965" (R-Car M3-N) + "renesas,msiof-r8a77970" (R-Car V3M) + "renesas,msiof-r8a77980" (R-Car V3H) + "renesas,msiof-r8a77990" (R-Car E3) + "renesas,msiof-r8a77995" (R-Car D3) "renesas,msiof-sh73a0" (SH-Mobile AG5) "renesas,sh-mobile-msiof" (generic SH-Mobile compatibile device) "renesas,rcar-gen2-msiof" (generic R-Car Gen2 and RZ/G1 compatible device) - "renesas,rcar-gen3-msiof" (generic R-Car Gen3 compatible device) + "renesas,rcar-gen3-msiof" (generic R-Car Gen3 and RZ/G2 compatible device) "renesas,sh-msiof" (deprecated) When compatible with the generic version, nodes diff --git a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt index 642d3fb1ef85..2864bc6b659c 100644 --- a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt +++ b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt @@ -2,7 +2,7 @@ Synopsys DesignWare AMBA 2.0 Synchronous Serial Interface. Required properties: - compatible : "snps,dw-apb-ssi" or "mscc,<soc>-spi", where soc is "ocelot" or - "jaguar2" + "jaguar2", or "amazon,alpine-dw-apb-ssi" - reg : The register base for the controller. For "mscc,<soc>-spi", a second register set is required (named ICPU_CFG:SPI_MST) - interrupts : One interrupt, used by the controller. diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt index 4af132606b37..8d178a4503cf 100644 --- a/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt @@ -3,6 +3,7 @@ Required properties: - compatible : - "fsl,imx7ulp-spi" for LPSPI compatible with the one integrated on i.MX7ULP soc + - "fsl,imx8qxp-spi" for LPSPI compatible with the one integrated on i.MX8QXP soc - reg : address and length of the lpspi master registers - interrupts : lpspi interrupt - clocks : lpspi clock specifier diff --git a/Documentation/devicetree/bindings/spi/spi-pxa2xx.txt b/Documentation/devicetree/bindings/spi/spi-pxa2xx.txt new file mode 100644 index 000000000000..0335a9bd2e8a --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-pxa2xx.txt @@ -0,0 +1,24 @@ +PXA2xx SSP SPI Controller + +Required properties: +- compatible: Must be "marvell,mmp2-ssp". +- reg: Offset and length of the device's register set. +- interrupts: Should be the interrupt number. +- clocks: Should contain a single entry describing the clock input. +- #address-cells: Number of cells required to define a chip select address. +- #size-cells: Should be zero. + +Optional properties: +- cs-gpios: list of GPIO chip selects. See the SPI bus bindings, + Documentation/devicetree/bindings/spi/spi-bus.txt + +Child nodes represent devices on the SPI bus + See ../spi/spi-bus.txt + +Example: + ssp1: spi@d4035000 { + compatible = "marvell,mmp2-ssp"; + reg = <0xd4035000 0x1000>; + clocks = <&soc_clocks MMP2_CLK_SSP0>; + interrupts = <0>; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-rspi.txt b/Documentation/devicetree/bindings/spi/spi-rspi.txt index 96fd58548f69..fc97ad64fbf2 100644 --- a/Documentation/devicetree/bindings/spi/spi-rspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-rspi.txt @@ -3,7 +3,7 @@ Device tree configuration for Renesas RSPI/QSPI driver Required properties: - compatible : For Renesas Serial Peripheral Interface on legacy SH: "renesas,rspi-<soctype>", "renesas,rspi" as fallback. - For Renesas Serial Peripheral Interface on RZ/A1H: + For Renesas Serial Peripheral Interface on RZ/A: "renesas,rspi-<soctype>", "renesas,rspi-rz" as fallback. For Quad Serial Peripheral Interface on R-Car Gen2 and RZ/G1 devices: @@ -11,7 +11,9 @@ Required properties: Examples with soctypes are: - "renesas,rspi-sh7757" (SH) - "renesas,rspi-r7s72100" (RZ/A1H) + - "renesas,rspi-r7s9210" (RZ/A2) - "renesas,qspi-r8a7743" (RZ/G1M) + - "renesas,qspi-r8a7744" (RZ/G1N) - "renesas,qspi-r8a7745" (RZ/G1E) - "renesas,qspi-r8a7790" (R-Car H2) - "renesas,qspi-r8a7791" (R-Car M2-W) diff --git a/Documentation/devicetree/bindings/spi/spi-slave-mt27xx.txt b/Documentation/devicetree/bindings/spi/spi-slave-mt27xx.txt new file mode 100644 index 000000000000..c37e5a179b21 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-slave-mt27xx.txt @@ -0,0 +1,32 @@ +Binding for MTK SPI Slave controller + +Required properties: +- compatible: should be one of the following. + - mediatek,mt2712-spi-slave: for mt2712 platforms +- reg: Address and length of the register set for the device. +- interrupts: Should contain spi interrupt. +- clocks: phandles to input clocks. + It's clock gate, and should be <&infracfg CLK_INFRA_AO_SPI1>. +- clock-names: should be "spi" for the clock gate. + +Optional properties: +- assigned-clocks: it's mux clock, should be <&topckgen CLK_TOP_SPISLV_SEL>. +- assigned-clock-parents: parent of mux clock. + It's PLL, and should be one of the following. + - <&topckgen CLK_TOP_UNIVPLL1_D2>: specify parent clock 312MHZ. + It's the default one. + - <&topckgen CLK_TOP_UNIVPLL1_D4>: specify parent clock 156MHZ. + - <&topckgen CLK_TOP_UNIVPLL2_D4>: specify parent clock 104MHZ. + - <&topckgen CLK_TOP_UNIVPLL1_D8>: specify parent clock 78MHZ. + +Example: +- SoC Specific Portion: +spis1: spi@10013000 { + compatible = "mediatek,mt2712-spi-slave"; + reg = <0 0x10013000 0 0x100>; + interrupts = <GIC_SPI 283 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_INFRA_AO_SPI1>; + clock-names = "spi"; + assigned-clocks = <&topckgen CLK_TOP_SPISLV_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL1_D2>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-sprd.txt b/Documentation/devicetree/bindings/spi/spi-sprd.txt new file mode 100644 index 000000000000..bad211a19da4 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-sprd.txt @@ -0,0 +1,26 @@ +Spreadtrum SPI Controller + +Required properties: +- compatible: Should be "sprd,sc9860-spi". +- reg: Offset and length of SPI controller register space. +- interrupts: Should contain SPI interrupt. +- clock-names: Should contain following entries: + "spi" for SPI clock, + "source" for SPI source (parent) clock, + "enable" for SPI module enable clock. +- clocks: List of clock input name strings sorted in the same order + as the clock-names property. +- #address-cells: The number of cells required to define a chip select + address on the SPI bus. Should be set to 1. +- #size-cells: Should be set to 0. + +Example: +spi0: spi@70a00000{ + compatible = "sprd,sc9860-spi"; + reg = <0 0x70a00000 0 0x1000>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "spi", "source","enable"; + clocks = <&clk_spi0>, <&ext_26m>, <&clk_ap_apb_gates 5>; + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt b/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt new file mode 100644 index 000000000000..adeeb63e84b9 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt @@ -0,0 +1,44 @@ +* STMicroelectronics Quad Serial Peripheral Interface(QSPI) + +Required properties: +- compatible: should be "st,stm32f469-qspi" +- reg: the first contains the register location and length. + the second contains the memory mapping address and length +- reg-names: should contain the reg names "qspi" "qspi_mm" +- interrupts: should contain the interrupt for the device +- clocks: the phandle of the clock needed by the QSPI controller +- A pinctrl must be defined to set pins in mode of operation for QSPI transfer + +Optional properties: +- resets: must contain the phandle to the reset controller. + +A spi flash (NOR/NAND) must be a child of spi node and could have some +properties. Also see jedec,spi-nor.txt. + +Required properties: +- reg: chip-Select number (QSPI controller may connect 2 flashes) +- spi-max-frequency: max frequency of spi bus + +Optional property: +- spi-rx-bus-width: see ./spi-bus.txt for the description + +Example: + +qspi: spi@a0001000 { + compatible = "st,stm32f469-qspi"; + reg = <0xa0001000 0x1000>, <0x90000000 0x10000000>; + reg-names = "qspi", "qspi_mm"; + interrupts = <91>; + resets = <&rcc STM32F4_AHB3_RESET(QSPI)>; + clocks = <&rcc 0 STM32F4_AHB3_CLOCK(QSPI)>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_qspi0>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-rx-bus-width = <4>; + spi-max-frequency = <108000000>; + ... + }; +}; diff --git a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt index 5d47a262474c..9407212a85a8 100644 --- a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt @@ -7,6 +7,7 @@ Required properties: Examples with soctypes are: - "renesas,r8a7743-wdt" (RZ/G1M) - "renesas,r8a7745-wdt" (RZ/G1E) + - "renesas,r8a774a1-wdt" (RZ/G2M) - "renesas,r8a7790-wdt" (R-Car H2) - "renesas,r8a7791-wdt" (R-Car M2-W) - "renesas,r8a7792-wdt" (R-Car V2H) @@ -21,8 +22,8 @@ Required properties: - "renesas,r7s72100-wdt" (RZ/A1) The generic compatible string must be: - "renesas,rza-wdt" for RZ/A - - "renesas,rcar-gen2-wdt" for R-Car Gen2 and RZ/G - - "renesas,rcar-gen3-wdt" for R-Car Gen3 + - "renesas,rcar-gen2-wdt" for R-Car Gen2 and RZ/G1 + - "renesas,rcar-gen3-wdt" for R-Car Gen3 and RZ/G2 - reg : Should contain WDT registers location and length - clocks : the clock feeding the watchdog timer. |