diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
16 files changed, 300 insertions, 75 deletions
diff --git a/Documentation/devicetree/bindings/mfd/tps65910.txt b/Documentation/devicetree/bindings/mfd/tps65910.txt index 645f5eaadb3f..d2802d4717bc 100644 --- a/Documentation/devicetree/bindings/mfd/tps65910.txt +++ b/Documentation/devicetree/bindings/mfd/tps65910.txt @@ -17,18 +17,46 @@ Required properties: device need to be present. The definition for each of these nodes is defined using the standard binding for regulators found at Documentation/devicetree/bindings/regulator/regulator.txt. + The regulator is matched with the regulator-compatible. - The valid names for regulators are: + The valid regulator-compatible values are: tps65910: vrtc, vio, vdd1, vdd2, vdd3, vdig1, vdig2, vpll, vdac, vaux1, vaux2, vaux33, vmmc tps65911: vrtc, vio, vdd1, vdd3, vddctrl, ldo1, ldo2, ldo3, ldo4, ldo5, ldo6, ldo7, ldo8 +- xxx-supply: Input voltage supply regulator. + These entries are require if regulators are enabled for a device. Missing of these + properties can cause the regulator registration fails. + If some of input supply is powered through battery or always-on supply then + also it is require to have these parameters with proper node handle of always + on power supply. + tps65910: + vcc1-supply: VDD1 input. + vcc2-supply: VDD2 input. + vcc3-supply: VAUX33 and VMMC input. + vcc4-supply: VAUX1 and VAUX2 input. + vcc5-supply: VPLL and VDAC input. + vcc6-supply: VDIG1 and VDIG2 input. + vcc7-supply: VRTC input. + vccio-supply: VIO input. + tps65911: + vcc1-supply: VDD1 input. + vcc2-supply: VDD2 input. + vcc3-supply: LDO6, LDO7 and LDO8 input. + vcc4-supply: LDO5 input. + vcc5-supply: LDO3 and LDO4 input. + vcc6-supply: LDO1 and LDO2 input. + vcc7-supply: VRTC input. + vccio-supply: VIO input. + Optional properties: - ti,vmbch-threshold: (tps65911) main battery charged threshold comparator. (see VMBCH_VSEL in TPS65910 datasheet) - ti,vmbch2-threshold: (tps65911) main battery discharged threshold comparator. (see VMBCH_VSEL in TPS65910 datasheet) +- ti,en-ck32k-xtal: enable external 32-kHz crystal oscillator (see CK32K_CTRL + in TPS6591X datasheet) - ti,en-gpio-sleep: enable sleep control for gpios There should be 9 entries here, one for each gpio. @@ -56,74 +84,110 @@ Example: ti,en-gpio-sleep = <0 0 1 0 0 0 0 0 0>; + vcc1-supply = <®_parent>; + vcc2-supply = <&some_reg>; + vcc3-supply = <...>; + vcc4-supply = <...>; + vcc5-supply = <...>; + vcc6-supply = <...>; + vcc7-supply = <...>; + vccio-supply = <...>; + regulators { - vdd1_reg: vdd1 { + #address-cells = <1>; + #size-cells = <0>; + + vdd1_reg: regulator@0 { + regulator-compatible = "vdd1"; + reg = <0>; regulator-min-microvolt = < 600000>; regulator-max-microvolt = <1500000>; regulator-always-on; regulator-boot-on; ti,regulator-ext-sleep-control = <0>; }; - vdd2_reg: vdd2 { + vdd2_reg: regulator@1 { + regulator-compatible = "vdd2"; + reg = <1>; regulator-min-microvolt = < 600000>; regulator-max-microvolt = <1500000>; regulator-always-on; regulator-boot-on; ti,regulator-ext-sleep-control = <4>; }; - vddctrl_reg: vddctrl { + vddctrl_reg: regulator@2 { + regulator-compatible = "vddctrl"; + reg = <2>; regulator-min-microvolt = < 600000>; regulator-max-microvolt = <1400000>; regulator-always-on; regulator-boot-on; ti,regulator-ext-sleep-control = <0>; }; - vio_reg: vio { + vio_reg: regulator@3 { + regulator-compatible = "vio"; + reg = <3>; regulator-min-microvolt = <1500000>; regulator-max-microvolt = <1800000>; regulator-always-on; regulator-boot-on; ti,regulator-ext-sleep-control = <1>; }; - ldo1_reg: ldo1 { + ldo1_reg: regulator@4 { + regulator-compatible = "ldo1"; + reg = <4>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; ti,regulator-ext-sleep-control = <0>; }; - ldo2_reg: ldo2 { + ldo2_reg: regulator@5 { + regulator-compatible = "ldo2"; + reg = <5>; regulator-min-microvolt = <1050000>; regulator-max-microvolt = <1050000>; ti,regulator-ext-sleep-control = <0>; }; - ldo3_reg: ldo3 { + ldo3_reg: regulator@6 { + regulator-compatible = "ldo3"; + reg = <6>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; ti,regulator-ext-sleep-control = <0>; }; - ldo4_reg: ldo4 { + ldo4_reg: regulator@7 { + regulator-compatible = "ldo4"; + reg = <7>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; regulator-always-on; ti,regulator-ext-sleep-control = <0>; }; - ldo5_reg: ldo5 { + ldo5_reg: regulator@8 { + regulator-compatible = "ldo5"; + reg = <8>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; ti,regulator-ext-sleep-control = <0>; }; - ldo6_reg: ldo6 { + ldo6_reg: regulator@9 { + regulator-compatible = "ldo6"; + reg = <9>; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; ti,regulator-ext-sleep-control = <0>; }; - ldo7_reg: ldo7 { + ldo7_reg: regulator@10 { + regulator-compatible = "ldo7"; + reg = <10>; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; regulator-always-on; regulator-boot-on; ti,regulator-ext-sleep-control = <1>; }; - ldo8_reg: ldo8 { + ldo8_reg: regulator@11 { + regulator-compatible = "ldo8"; + reg = <11>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; regulator-always-on; diff --git a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt index 0d93b4b0e0e3..bd9be0b5bc20 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt @@ -3,21 +3,22 @@ The Enhanced Secure Digital Host Controller provides an interface for MMC, SD, and SDIO types of memory cards. +This file documents differences between the core properties described +by mmc.txt and the properties used by the sdhci-esdhc driver. + Required properties: - - compatible : should be - "fsl,<chip>-esdhc", "fsl,esdhc" - - reg : should contain eSDHC registers location and length. - - interrupts : should contain eSDHC interrupt. - interrupt-parent : interrupt source phandle. - clock-frequency : specifies eSDHC base clock frequency. - - sdhci,wp-inverted : (optional) specifies that eSDHC controller - reports inverted write-protect state; New devices should use - the generic "wp-inverted" property. - - sdhci,1-bit-only : (optional) specifies that a controller can - only handle 1-bit data transfers. New devices should use the - generic "bus-width = <1>" property. - - sdhci,auto-cmd12: (optional) specifies that a controller can - only handle auto CMD12. + +Optional properties: + - sdhci,wp-inverted : specifies that eSDHC controller reports + inverted write-protect state; New devices should use the generic + "wp-inverted" property. + - sdhci,1-bit-only : specifies that a controller can only handle + 1-bit data transfers. New devices should use the generic + "bus-width = <1>" property. + - sdhci,auto-cmd12: specifies that a controller can only handle auto + CMD12. Example: diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt index fea541ee8b34..70cd49b1caa8 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -3,17 +3,15 @@ The Enhanced Secure Digital Host Controller on Freescale i.MX family provides an interface for MMC, SD, and SDIO types of memory cards. +This file documents differences between the core properties described +by mmc.txt and the properties used by the sdhci-esdhc-imx driver. + Required properties: - compatible : Should be "fsl,<chip>-esdhc" -- reg : Should contain eSDHC registers location and length -- interrupts : Should contain eSDHC interrupt Optional properties: -- non-removable : Indicate the card is wired to host permanently - fsl,cd-internal : Indicate to use controller internal card detection - fsl,wp-internal : Indicate to use controller internal write protection -- cd-gpios : Specify GPIOs for card detection -- wp-gpios : Specify GPIOs for write protection Examples: diff --git a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt index d64aea5a4203..0e5e2ec4001d 100644 --- a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt +++ b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt @@ -1,8 +1,9 @@ MMC/SD/SDIO slot directly connected to a SPI bus +This file documents differences between the core properties described +by mmc.txt and the properties used by the mmc_spi driver. + Required properties: -- compatible : should be "mmc-spi-slot". -- reg : should specify SPI address (chip-select number). - spi-max-frequency : maximum frequency for this device (Hz). - voltage-ranges : two cells are required, first cell specifies minimum slot voltage (mV), second cell specifies maximum slot voltage (mV). @@ -11,8 +12,7 @@ Required properties: Optional properties: - gpios : may specify GPIOs in this order: Card-Detect GPIO, Write-Protect GPIO. Note that this does not follow the - binding from mmc.txt, for historic reasons. -- interrupts : the interrupt of a card detect interrupt. + binding from mmc.txt, for historical reasons. - interrupt-parent : the phandle for the interrupt controller that services interrupts for this device. diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 6e70dcde0a71..8a6811f4a02f 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -2,13 +2,17 @@ These properties are common to multiple MMC host controllers. Any host that requires the respective functionality should implement them using these definitions. +Interpreted by the OF core: +- reg: Registers location and length. +- interrupts: Interrupts used by the MMC controller. + Required properties: - bus-width: Number of data lines, can be <1>, <4>, or <8> Optional properties: -- cd-gpios : Specify GPIOs for card detection, see gpio binding -- wp-gpios : Specify GPIOs for write protection, see gpio binding -- cd-inverted: when present, polarity on the wp gpio line is inverted +- cd-gpios: Specify GPIOs for card detection, see gpio binding +- wp-gpios: Specify GPIOs for write protection, see gpio binding +- cd-inverted: when present, polarity on the cd gpio line is inverted - wp-inverted: when present, polarity on the wp gpio line is inverted - non-removable: non-removable slot (like eMMC) - max-frequency: maximum operating clock frequency diff --git a/Documentation/devicetree/bindings/mmc/mmci.txt b/Documentation/devicetree/bindings/mmc/mmci.txt index 14a81d526118..2b584cae352a 100644 --- a/Documentation/devicetree/bindings/mmc/mmci.txt +++ b/Documentation/devicetree/bindings/mmc/mmci.txt @@ -1,19 +1,15 @@ * ARM PrimeCell MultiMedia Card Interface (MMCI) PL180/1 -The ARM PrimeCell MMCI PL180 and PL181 provides and interface for +The ARM PrimeCell MMCI PL180 and PL181 provides an interface for reading and writing to MultiMedia and SD cards alike. +This file documents differences between the core properties described +by mmc.txt and the properties used by the mmci driver. + Required properties: - compatible : contains "arm,pl18x", "arm,primecell". -- reg : contains pl18x registers and length. -- interrupts : contains the device IRQ(s). - arm,primecell-periphid : contains the PrimeCell Peripheral ID. Optional properties: -- wp-gpios : contains any write protect (ro) gpios -- cd-gpios : contains any card detection gpios -- cd-inverted : indicates whether the cd gpio is inverted -- max-frequency : contains the maximum operating frequency -- bus-width : number of data lines, can be <1>, <4>, or <8> - mmc-cap-mmc-highspeed : indicates whether MMC is high speed capable - mmc-cap-sd-highspeed : indicates whether SD is high speed capable diff --git a/Documentation/devicetree/bindings/mmc/mxs-mmc.txt b/Documentation/devicetree/bindings/mmc/mxs-mmc.txt index 14d870a9e3db..54949f6faede 100644 --- a/Documentation/devicetree/bindings/mmc/mxs-mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mxs-mmc.txt @@ -3,16 +3,14 @@ The Freescale MXS Synchronous Serial Ports (SSP) can act as a MMC controller to support MMC, SD, and SDIO types of memory cards. +This file documents differences between the core properties in mmc.txt +and the properties used by the mxsmmc driver. + Required properties: - compatible: Should be "fsl,<chip>-mmc". The supported chips include imx23 and imx28. -- reg: Should contain registers location and length - interrupts: Should contain ERROR and DMA interrupts - fsl,ssp-dma-channel: APBH DMA channel for the SSP -- bus-width: Number of data lines, can be <1>, <4>, or <8> - -Optional properties: -- wp-gpios: Specify GPIOs for write protection Examples: diff --git a/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt index f77c3031607f..c6d7b11db9eb 100644 --- a/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt @@ -3,15 +3,13 @@ This controller on Tegra family SoCs provides an interface for MMC, SD, and SDIO types of memory cards. +This file documents differences between the core properties described +by mmc.txt and the properties used by the sdhci-tegra driver. + Required properties: - compatible : Should be "nvidia,<chip>-sdhci" -- reg : Should contain SD/MMC registers location and length -- interrupts : Should contain SD/MMC interrupt -- bus-width : Number of data lines, can be <1>, <4>, or <8> Optional properties: -- cd-gpios : Specify GPIOs for card detection -- wp-gpios : Specify GPIOs for write protection - power-gpios : Specify GPIOs for power control Example: diff --git a/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt b/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt new file mode 100644 index 000000000000..dbe98a3c183a --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt @@ -0,0 +1,21 @@ +* Marvell sdhci-pxa v2/v3 controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-pxav2 and sdhci-pxav3 drivers. + +Required properties: +- compatible: Should be "mrvl,pxav2-mmc" or "mrvl,pxav3-mmc". + +Optional properties: +- mrvl,clk-delay-cycles: Specify a number of cycles to delay for tuning. + +Example: + +sdhci@d4280800 { + compatible = "mrvl,pxav3-mmc"; + reg = <0xd4280800 0x800>; + bus-width = <8>; + interrupts = <27>; + non-removable; + mrvl,clk-delay-cycles = <31>; +}; diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt index 8a53958c9a9f..be76a23b34c4 100644 --- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt @@ -3,21 +3,20 @@ The Highspeed MMC Host Controller on TI OMAP family provides an interface for MMC, SD, and SDIO types of memory cards. +This file documents differences between the core properties described +by mmc.txt and the properties used by the omap_hsmmc driver. + Required properties: - compatible: Should be "ti,omap2-hsmmc", for OMAP2 controllers Should be "ti,omap3-hsmmc", for OMAP3 controllers Should be "ti,omap4-hsmmc", for OMAP4 controllers - ti,hwmods: Must be "mmc<n>", n is controller instance starting 1 -- reg : should contain hsmmc registers location and length Optional properties: ti,dual-volt: boolean, supports dual voltage cards <supply-name>-supply: phandle to the regulator device tree node "supply-name" examples are "vmmc", "vmmc_aux" etc -bus-width: Number of data lines, default assumed is 1 if the property is missing. -cd-gpios: GPIOs for card detection -wp-gpios: GPIOs for write protection ti,non-removable: non-removable slot (like eMMC) ti,needs-special-reset: Requires a special softreset sequence diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx6q-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx6q-pinctrl.txt index 82b43f915857..a4119f6422d9 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx6q-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx6q-pinctrl.txt @@ -1626,3 +1626,5 @@ MX6Q_PAD_SD2_DAT3__PCIE_CTRL_MUX_11 1587 MX6Q_PAD_SD2_DAT3__GPIO_1_12 1588 MX6Q_PAD_SD2_DAT3__SJC_DONE 1589 MX6Q_PAD_SD2_DAT3__ANATOP_TESTO_3 1590 +MX6Q_PAD_ENET_RX_ER__ANATOP_USBOTG_ID 1591 +MX6Q_PAD_GPIO_1__ANATOP_USBOTG_ID 1592 diff --git a/Documentation/devicetree/bindings/regulator/fixed-regulator.txt b/Documentation/devicetree/bindings/regulator/fixed-regulator.txt index 2f5b6b1ba15f..4fae41d54798 100644 --- a/Documentation/devicetree/bindings/regulator/fixed-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/fixed-regulator.txt @@ -10,6 +10,7 @@ Optional properties: If this property is missing, the default assumed is Active low. - gpio-open-drain: GPIO is open drain type. If this property is missing then default assumption is false. +-vin-supply: Input supply name. Any property defined as part of the core regulator binding, defined in regulator.txt, can also be used. @@ -29,4 +30,5 @@ Example: enable-active-high; regulator-boot-on; gpio-open-drain; + vin-supply = <&parent_reg>; }; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 5b7a408acdaa..66ece3f87bbc 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -10,6 +10,11 @@ Optional properties: - regulator-always-on: boolean, regulator should never be disabled - regulator-boot-on: bootloader/firmware enabled regulator - <name>-supply: phandle to the parent supply/regulator node +- regulator-ramp-delay: ramp delay for regulator(in uV/uS) +- regulator-compatible: If a regulator chip contains multiple + regulators, and if the chip's binding contains a child node that + describes each regulator, then this property indicates which regulator + this child node is intended to configure. Example: diff --git a/Documentation/devicetree/bindings/regulator/tps65217.txt b/Documentation/devicetree/bindings/regulator/tps65217.txt new file mode 100644 index 000000000000..0487e9675ba0 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/tps65217.txt @@ -0,0 +1,91 @@ +TPS65217 family of regulators + +Required properties: +- compatible: "ti,tps65217" +- reg: I2C slave address +- regulators: list of regulators provided by this controller, must be named + after their hardware counterparts: dcdc[1-3] and ldo[1-4] +- regulators: This is the list of child nodes that specify the regulator + initialization data for defined regulators. Not all regulators for the given + device need to be present. The definition for each of these nodes is defined + using the standard binding for regulators found at + Documentation/devicetree/bindings/regulator/regulator.txt. + + The valid names for regulators are: + tps65217: dcdc1, dcdc2, dcdc3, ldo1, ldo2, ldo3 and ldo4 + +Each regulator is defined using the standard binding for regulators. + +Example: + + tps: tps@24 { + compatible = "ti,tps65217"; + + regulators { + #address-cells = <1>; + #size-cells = <0>; + + dcdc1_reg: regulator@0 { + reg = <0>; + regulator-compatible = "dcdc1"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc2_reg: regulator@1 { + reg = <1>; + regulator-compatible = "dcdc2"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3_reg: regulator@2 { + reg = <2>; + regulator-compatible = "dcdc3"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: regulator@3 { + reg = <3>; + regulator-compatible = "ldo1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: regulator@4 { + reg = <4>; + regulator-compatible = "ldo2"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: regulator@5 { + reg = <5>; + regulator-compatible = "ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: regulator@6 { + reg = <6>; + regulator-compatible = "ldo4"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/tps6586x.txt b/Documentation/devicetree/bindings/regulator/tps6586x.txt index 0fcabaa3baa3..d156e1b5db12 100644 --- a/Documentation/devicetree/bindings/regulator/tps6586x.txt +++ b/Documentation/devicetree/bindings/regulator/tps6586x.txt @@ -6,8 +6,17 @@ Required properties: - interrupts: the interrupt outputs of the controller - #gpio-cells: number of cells to describe a GPIO - gpio-controller: mark the device as a GPIO controller -- regulators: list of regulators provided by this controller, must be named - after their hardware counterparts: sm[0-2], ldo[0-9] and ldo_rtc +- regulators: list of regulators provided by this controller, must have + property "regulator-compatible" to match their hardware counterparts: + sm[0-2], ldo[0-9] and ldo_rtc +- sm0-supply: The input supply for the SM0. +- sm1-supply: The input supply for the SM1. +- sm2-supply: The input supply for the SM2. +- vinldo01-supply: The input supply for the LDO1 and LDO2 +- vinldo23-supply: The input supply for the LDO2 and LDO3 +- vinldo4-supply: The input supply for the LDO4 +- vinldo678-supply: The input supply for the LDO6, LDO7 and LDO8 +- vinldo9-supply: The input supply for the LDO9 Each regulator is defined using the standard binding for regulators. @@ -21,75 +30,113 @@ Example: #gpio-cells = <2>; gpio-controller; + sm0-supply = <&some_reg>; + sm1-supply = <&some_reg>; + sm2-supply = <&some_reg>; + vinldo01-supply = <...>; + vinldo23-supply = <...>; + vinldo4-supply = <...>; + vinldo678-supply = <...>; + vinldo9-supply = <...>; + regulators { - sm0_reg: sm0 { + #address-cells = <1>; + #size-cells = <0>; + + sm0_reg: regulator@0 { + reg = <0>; + regulator-compatible = "sm0"; regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; regulator-boot-on; regulator-always-on; }; - sm1_reg: sm1 { + sm1_reg: regulator@1 { + reg = <1>; + regulator-compatible = "sm1"; regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; regulator-boot-on; regulator-always-on; }; - sm2_reg: sm2 { + sm2_reg: regulator@2 { + reg = <2>; + regulator-compatible = "sm2"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <4550000>; regulator-boot-on; regulator-always-on; }; - ldo0_reg: ldo0 { + ldo0_reg: regulator@3 { + reg = <3>; + regulator-compatible = "ldo0"; regulator-name = "PCIE CLK"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; - ldo1_reg: ldo1 { + ldo1_reg: regulator@4 { + reg = <4>; + regulator-compatible = "ldo1"; regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; }; - ldo2_reg: ldo2 { + ldo2_reg: regulator@5 { + reg = <5>; + regulator-compatible = "ldo2"; regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; }; - ldo3_reg: ldo3 { + ldo3_reg: regulator@6 { + reg = <6>; + regulator-compatible = "ldo3"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo4_reg: ldo4 { + ldo4_reg: regulator@7 { + reg = <7>; + regulator-compatible = "ldo4"; regulator-min-microvolt = <1700000>; regulator-max-microvolt = <2475000>; }; - ldo5_reg: ldo5 { + ldo5_reg: regulator@8 { + reg = <8>; + regulator-compatible = "ldo5"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo6_reg: ldo6 { + ldo6_reg: regulator@9 { + reg = <9>; + regulator-compatible = "ldo6"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo7_reg: ldo7 { + ldo7_reg: regulator@10 { + reg = <10>; + regulator-compatible = "ldo7"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo8_reg: ldo8 { + ldo8_reg: regulator@11 { + reg = <11>; + regulator-compatible = "ldo8"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo9_reg: ldo9 { + ldo9_reg: regulator@12 { + reg = <12>; + regulator-compatible = "ldo9"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; diff --git a/Documentation/devicetree/bindings/regulator/twl-regulator.txt b/Documentation/devicetree/bindings/regulator/twl-regulator.txt index 0c3395d55ac1..658749b90b97 100644 --- a/Documentation/devicetree/bindings/regulator/twl-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/twl-regulator.txt @@ -15,7 +15,6 @@ For twl6030 regulators/LDOs - "ti,twl6030-vusb" for VUSB LDO - "ti,twl6030-v1v8" for V1V8 LDO - "ti,twl6030-v2v1" for V2V1 LDO - - "ti,twl6030-clk32kg" for CLK32KG RESOURCE - "ti,twl6030-vdd1" for VDD1 SMPS - "ti,twl6030-vdd2" for VDD2 SMPS - "ti,twl6030-vdd3" for VDD3 SMPS |