diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
91 files changed, 1718 insertions, 149 deletions
diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt index 0fff40a6330d..4e4bc0bae597 100644 --- a/Documentation/devicetree/bindings/arm/amlogic.txt +++ b/Documentation/devicetree/bindings/arm/amlogic.txt @@ -1,6 +1,18 @@ Amlogic MesonX device tree bindings ------------------------------------------- +Work in progress statement: + +Device tree files and bindings applying to Amlogic SoCs and boards are +considered "unstable". Any Amlogic device tree binding may change at +any time. Be sure to use a device tree binary and a kernel image +generated from the same source tree. + +Please refer to Documentation/devicetree/bindings/ABI.txt for a definition of a +stable binding/ABI. + +--------------------------------------------------------------- + Boards with the Amlogic Meson6 SoC shall have the following properties: Required root node property: compatible: "amlogic,meson6" @@ -61,3 +73,32 @@ Board compatible values (alphabetically, grouped by SoC): - "amlogic,q201" (Meson gxm s912) - "kingnovel,r-box-pro" (Meson gxm S912) - "nexbox,a1" (Meson gxm s912) + +Amlogic Meson Firmware registers Interface +------------------------------------------ + +The Meson SoCs have a register bank with status and data shared with the +secure firmware. + +Required properties: + - compatible: For Meson GX SoCs, must be "amlogic,meson-gx-ao-secure", "syscon" + +Properties should indentify components of this register interface : + +Meson GX SoC Information +------------------------ +A firmware register encodes the SoC type, package and revision information on +the Meson GX SoCs. +If present, the following property should be added : + +Optional properties: + - amlogic,has-chip-id: If present, the interface gives the current SoC version. + +Example +------- + +ao-secure@140 { + compatible = "amlogic,meson-gx-ao-secure", "syscon"; + reg = <0x0 0x140 0x0 0x140>; + amlogic,has-chip-id; +}; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt index 9c97de23919a..3e3efa046ac5 100644 --- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt @@ -42,6 +42,10 @@ Raspberry Pi Zero Required root node properties: compatible = "raspberrypi,model-zero", "brcm,bcm2835"; +Raspberry Pi Zero W +Required root node properties: +compatible = "raspberrypi,model-zero-w", "brcm,bcm2835"; + Generic BCM2835 board Required root node properties: compatible = "brcm,bcm2835"; diff --git a/Documentation/devicetree/bindings/arm/bhf.txt b/Documentation/devicetree/bindings/arm/bhf.txt new file mode 100644 index 000000000000..886b503caf9c --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bhf.txt @@ -0,0 +1,6 @@ +Beckhoff Automation Platforms Device Tree Bindings +-------------------------------------------------- + +CX9020 Embedded PC +Required root node properties: + - compatible = "bhf,cx9020", "fsl,imx53"; diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index a44253cad269..b92f12bd5244 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -200,6 +200,7 @@ described below. "arm,realview-smp" "brcm,bcm11351-cpu-method" "brcm,bcm23550" + "brcm,bcm2836-smp" "brcm,bcm-nsp-smp" "brcm,brahma-b15" "marvell,armada-375-smp" diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-8kp.txt b/Documentation/devicetree/bindings/arm/marvell/armada-8kp.txt new file mode 100644 index 000000000000..f3e9624534c6 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/marvell/armada-8kp.txt @@ -0,0 +1,15 @@ +Marvell Armada 8KPlus Platforms Device Tree Bindings +---------------------------------------------------- + +Boards using a SoC of the Marvell Armada 8KP families must carry +the following root node property: + + - compatible, with one of the following values: + + - "marvell,armada-8080", "marvell,armada-ap810-octa", "marvell,armada-ap810" + when the SoC being used is the Armada 8080 + +Example: + +compatible = "marvell,armada-8080-db", "marvell,armada-8080", + "marvell,armada-ap810-octa", "marvell,armada-ap810" diff --git a/Documentation/devicetree/bindings/arm/mediatek.txt b/Documentation/devicetree/bindings/arm/mediatek.txt index da7bd138e6f2..91d517849483 100644 --- a/Documentation/devicetree/bindings/arm/mediatek.txt +++ b/Documentation/devicetree/bindings/arm/mediatek.txt @@ -1,12 +1,12 @@ -MediaTek mt65xx, mt67xx & mt81xx Platforms Device Tree Bindings +MediaTek SoC based Platforms Device Tree Bindings -Boards with a MediaTek mt65xx/mt67xx/mt81xx SoC shall have the -following property: +Boards with a MediaTek SoC shall have the following property: Required root node property: compatible: Must contain one of "mediatek,mt2701" + "mediatek,mt2712" "mediatek,mt6580" "mediatek,mt6589" "mediatek,mt6592" @@ -14,7 +14,8 @@ compatible: Must contain one of "mediatek,mt6795" "mediatek,mt6797" "mediatek,mt7622" - "mediatek,mt7623" + "mediatek,mt7623" which is referred to MT7623N SoC + "mediatek,mt7623a" "mediatek,mt8127" "mediatek,mt8135" "mediatek,mt8173" @@ -25,6 +26,9 @@ Supported boards: - Evaluation board for MT2701: Required root node properties: - compatible = "mediatek,mt2701-evb", "mediatek,mt2701"; +- Evaluation board for MT2712: + Required root node properties: + - compatible = "mediatek,mt2712-evb", "mediatek,mt2712"; - Evaluation board for MT6580: Required root node properties: - compatible = "mediatek,mt6580-evbp1", "mediatek,mt6580"; @@ -46,9 +50,11 @@ Supported boards: - Reference board variant 1 for MT7622: Required root node properties: - compatible = "mediatek,mt7622-rfb1", "mediatek,mt7622"; -- Evaluation board for MT7623: +- Reference board for MT7623n with NAND: Required root node properties: - - compatible = "mediatek,mt7623-evb", "mediatek,mt7623"; + - compatible = "mediatek,mt7623n-rfb-nand", "mediatek,mt7623"; +- Bananapi BPI-R2 board: + - compatible = "bananapi,bpi-r2", "mediatek,mt7623"; - MTK mt8127 tablet moose EVB: Required root node properties: - compatible = "mediatek,mt8127-moose", "mediatek,mt8127"; diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 8219b2c6bb29..2ecc712bf707 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -80,6 +80,9 @@ SoCs: - OMAP5432 compatible = "ti,omap5432", "ti,omap5" +- DRA762 + compatible = "ti,dra762", "ti,dra7" + - DRA742 compatible = "ti,dra742", "ti,dra74", "ti,dra7" @@ -154,6 +157,9 @@ Boards: - AM335X phyCORE-AM335x: Development kit compatible = "phytec,am335x-pcm-953", "phytec,am335x-phycore-som", "ti,am33xx" +- AM335X UC-8100-ME-T: Communication-centric industrial computing platform + compatible = "moxa,uc-8100-me-t", "ti,am33xx"; + - OMAP5 EVM : Evaluation Module compatible = "ti,omap5-evm", "ti,omap5" @@ -184,6 +190,9 @@ Boards: - AM5718 IDK compatible = "ti,am5718-idk", "ti,am5718", "ti,dra7" +- DRA762 EVM: Software Development Board for DRA762 + compatible = "ti,dra76-evm", "ti,dra762", "ti,dra7" + - DRA742 EVM: Software Development Board for DRA742 compatible = "ti,dra7-evm", "ti,dra742", "ti,dra74", "ti,dra7" diff --git a/Documentation/devicetree/bindings/arm/qcom.txt b/Documentation/devicetree/bindings/arm/qcom.txt index 028d16e72186..0ed4d39d7fe1 100644 --- a/Documentation/devicetree/bindings/arm/qcom.txt +++ b/Documentation/devicetree/bindings/arm/qcom.txt @@ -25,6 +25,7 @@ The 'SoC' element must be one of the following strings: msm8994 msm8996 mdm9615 + ipq8074 The 'board' element must be one of the following strings: @@ -33,6 +34,7 @@ The 'board' element must be one of the following strings: dragonboard mtp sbc + hk01 The 'soc_version' and 'board_version' elements take the form of v<Major>.<Minor> where the minor number may be omitted when it's zero, i.e. v1.0 is the same diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index 11c0ac4a2d56..b003148e2945 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -134,6 +134,10 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "phytec,rk3288-pcm-947", "phytec,rk3288-phycore-som", "rockchip,rk3288"; +- Pine64 Rock64 board: + Required root node properties: + - compatible = "pine64,rock64", "rockchip,rk3328"; + - Rockchip PX3 Evaluation board: Required root node properties: - compatible = "rockchip,px3-evb", "rockchip,px3", "rockchip,rk3188"; @@ -173,6 +177,14 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "rockchip,rk3399-evb", "rockchip,rk3399"; +- Rockchip RK3399 Sapphire Excavator board: + Required root node properties: + - compatible = "rockchip,rk3399-sapphire-excavator", "rockchip,rk3399"; + +- Theobroma Systems RK3399-Q7 Haikou Baseboard: + Required root node properties: + - compatible = "tsd,rk3399-q7-haikou", "rockchip,rk3399"; + - Tronsmart Orion R68 Meta Required root node properties: - compatible = "tronsmart,orion-r68-meta", "rockchip,rk3368"; diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt index 1a671e329864..ae75cb3b1331 100644 --- a/Documentation/devicetree/bindings/arm/shmobile.txt +++ b/Documentation/devicetree/bindings/arm/shmobile.txt @@ -39,6 +39,8 @@ SoCs: compatible = "renesas,r8a7795" - R-Car M3-W (R8A77960) compatible = "renesas,r8a7796" + - R-Car D3 (R8A77995) + compatible = "renesas,r8a77995" Boards: @@ -53,6 +55,8 @@ Boards: compatible = "renesas,blanche", "renesas,r8a7792" - BOCK-W compatible = "renesas,bockw", "renesas,r8a7778" + - Draak (RTP0RC77995SEB0010S) + compatible = "renesas,draak", "renesas,r8a77995" - Genmai (RTK772100BC00000BR) compatible = "renesas,genmai", "renesas,r7s72100" - GR-Peach (X28A-M01-E/F) @@ -64,6 +68,10 @@ Boards: compatible = "renesas,h3ulcb", "renesas,r8a7795"; - Henninger compatible = "renesas,henninger", "renesas,r8a7791" + - iWave Systems RZ/G1E SODIMM SOM Development Platform (iW-RainboW-G22D) + compatible = "iwave,g22d", "iwave,g22m", "renesas,r8a7745" + - iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM) + compatible = "iwave,g22m", "renesas,r8a7745" - iWave Systems RZ/G1M Qseven Development Platform (iW-RainboW-G20D-Qseven) compatible = "iwave,g20d", "iwave,g20m", "renesas,r8a7743" - iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven) diff --git a/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt b/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt index faa6d8ac5834..786dc39ca904 100644 --- a/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt +++ b/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt @@ -5,9 +5,11 @@ controllers within the Always-On part of the SoC. Required Properties: -- compatible: should be "amlogic,gxbb-aoclkc" -- reg: physical base address of the clock controller and length of memory - mapped region. +- compatible: value should be different for each SoC family as : + - GXBB (S905) : "amlogic,meson-gxbb-aoclkc" + - GXL (S905X, S905D) : "amlogic,meson-gxl-aoclkc" + - GXM (S912) : "amlogic,meson-gxm-aoclkc" + followed by the common "amlogic,meson-gx-aoclkc" - #clock-cells: should be 1. @@ -23,14 +25,22 @@ to specify the reset which they consume. All available resets are defined as preprocessor macros in the dt-bindings/reset/gxbb-aoclkc.h header and can be used in device tree sources. +Parent node should have the following properties : +- compatible: "amlogic,meson-gx-ao-sysctrl", "syscon", "simple-mfd" +- reg: base address and size of the AO system control register space. + Example: AO Clock controller node: - clkc_AO: clock-controller@040 { - compatible = "amlogic,gxbb-aoclkc"; - reg = <0x0 0x040 0x0 0x4>; +ao_sysctrl: sys-ctrl@0 { + compatible = "amlogic,meson-gx-ao-sysctrl", "syscon", "simple-mfd"; + reg = <0x0 0x0 0x0 0x100>; + + clkc_AO: clock-controller { + compatible = "amlogic,meson-gxbb-aoclkc", "amlogic,meson-gx-aoclkc"; #clock-cells = <1>; #reset-cells = <1>; }; +}; Example: UART controller node that consumes the clock and reset generated by the clock controller: diff --git a/Documentation/devicetree/bindings/clock/amlogic,meson8b-clkc.txt b/Documentation/devicetree/bindings/clock/amlogic,meson8b-clkc.txt index 207682647d33..b455c5aa9139 100644 --- a/Documentation/devicetree/bindings/clock/amlogic,meson8b-clkc.txt +++ b/Documentation/devicetree/bindings/clock/amlogic,meson8b-clkc.txt @@ -16,18 +16,25 @@ Required Properties: mapped region. - #clock-cells: should be 1. +- #reset-cells: should be 1. Each clock is assigned an identifier and client nodes can use this identifier to specify the clock which they consume. All available clocks are defined as preprocessor macros in the dt-bindings/clock/meson8b-clkc.h header and can be used in device tree sources. +Similarly a preprocessor macro for each reset line is defined in +dt-bindings/reset/amlogic,meson8b-clkc-reset.h (which can be used from the +device tree sources). + + Example: Clock controller node: clkc: clock-controller@c1104000 { - #clock-cells = <1>; compatible = "amlogic,meson8b-clkc"; reg = <0xc1108000 0x4>, <0xc1104000 0x460>; + #clock-cells = <1>; + #reset-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt index 5f3ad65daf69..51c259a92d02 100644 --- a/Documentation/devicetree/bindings/clock/at91-clock.txt +++ b/Documentation/devicetree/bindings/clock/at91-clock.txt @@ -81,6 +81,16 @@ Required properties: "atmel,sama5d2-clk-generated": at91 generated clock + "atmel,sama5d2-clk-audio-pll-frac": + at91 audio fractional pll + + "atmel,sama5d2-clk-audio-pll-pad": + at91 audio pll CLK_AUDIO output pin + + "atmel,sama5d2-clk-audio-pll-pmc" + at91 audio pll output on AUDIOPLLCLK that feeds the PMC + and can be used by peripheral clock or generic clock + Required properties for SCKC node: - reg : defines the IO memory reserved for the SCKC. - #size-cells : shall be 0 (reg is used to encode clk id). diff --git a/Documentation/devicetree/bindings/clock/idt,versaclock5.txt b/Documentation/devicetree/bindings/clock/idt,versaclock5.txt index 53d7e50ed875..05a245c9df08 100644 --- a/Documentation/devicetree/bindings/clock/idt,versaclock5.txt +++ b/Documentation/devicetree/bindings/clock/idt,versaclock5.txt @@ -1,24 +1,32 @@ -Binding for IDT VersaClock5 programmable i2c clock generator. +Binding for IDT VersaClock 5,6 programmable i2c clock generators. -The IDT VersaClock5 are programmable i2c clock generators providing -from 3 to 12 output clocks. +The IDT VersaClock 5 and VersaClock 6 are programmable i2c clock +generators providing from 3 to 12 output clocks. ==I2C device node== Required properties: -- compatible: shall be one of "idt,5p49v5923" , "idt,5p49v5933" , - "idt,5p49v5935". +- compatible: shall be one of + "idt,5p49v5923" + "idt,5p49v5925" + "idt,5p49v5933" + "idt,5p49v5935" + "idt,5p49v6901" - reg: i2c device address, shall be 0x68 or 0x6a. - #clock-cells: from common clock binding; shall be set to 1. - clocks: from common clock binding; list of parent clock handles, - - 5p49v5923: (required) either or both of XTAL or CLKIN + - 5p49v5923 and + 5p49v5925 and + 5p49v6901: (required) either or both of XTAL or CLKIN reference clock. - 5p49v5933 and - 5p49v5935: (optional) property not present (internal Xtal used) or CLKIN reference clock. - clock-names: from common clock binding; clock input names, can be - - 5p49v5923: (required) either or both of "xin", "clkin". + - 5p49v5923 and + 5p49v5925 and + 5p49v6901: (required) either or both of "xin", "clkin". - 5p49v5933 and - 5p49v5935: (optional) property not present or "clkin". @@ -37,6 +45,7 @@ clock specifier, the following mapping applies: 1 -- OUT1 2 -- OUT4 +5P49V5925 and 5P49V5935: 0 -- OUT0_SEL_I2CB 1 -- OUT1 @@ -44,6 +53,13 @@ clock specifier, the following mapping applies: 3 -- OUT3 4 -- OUT4 +5P49V6901: + 0 -- OUT0_SEL_I2CB + 1 -- OUT1 + 2 -- OUT2 + 3 -- OUT3 + 4 -- OUT4 + ==Example== /* 25MHz reference crystal */ diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt index 707a686d8d3e..316e13686568 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt @@ -22,6 +22,7 @@ Required Properties: - "renesas,r8a7794-cpg-mssr" for the r8a7794 SoC (R-Car E2) - "renesas,r8a7795-cpg-mssr" for the r8a7795 SoC (R-Car H3) - "renesas,r8a7796-cpg-mssr" for the r8a7796 SoC (R-Car M3-W) + - "renesas,r8a77995-cpg-mssr" for the r8a77995 SoC (R-Car D3) - reg: Base address and length of the memory resource used by the CPG/MSSR block @@ -30,7 +31,7 @@ Required Properties: clock-names - clock-names: List of external parent clock names. Valid names are: - "extal" (r8a7743, r8a7745, r8a7790, r8a7791, r8a7792, r8a7793, r8a7794, - r8a7795, r8a7796) + r8a7795, r8a7796, r8a77995) - "extalr" (r8a7795, r8a7796) - "usb_extal" (r8a7743, r8a7745, r8a7790, r8a7791, r8a7793, r8a7794) diff --git a/Documentation/devicetree/bindings/clock/renesas,rcar-usb2-clock-sel.txt b/Documentation/devicetree/bindings/clock/renesas,rcar-usb2-clock-sel.txt new file mode 100644 index 000000000000..e96e085271c1 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,rcar-usb2-clock-sel.txt @@ -0,0 +1,55 @@ +* Renesas R-Car USB 2.0 clock selector + +This file provides information on what the device node for the R-Car USB 2.0 +clock selector. + +If you connect an external clock to the USB_EXTAL pin only, you should set +the clock rate to "usb_extal" node only. +If you connect an oscillator to both the USB_XTAL and USB_EXTAL, this module +is not needed because this is default setting. (Of course, you can set the +clock rates to both "usb_extal" and "usb_xtal" nodes. + +Case 1: An external clock connects to R-Car SoC + +----------+ +--- R-Car ---------------------+ + |External |---|USB_EXTAL ---> all usb channels| + |clock | |USB_XTAL | + +----------+ +-------------------------------+ +In this case, we need this driver with "usb_extal" clock. + +Case 2: An oscillator connects to R-Car SoC + +----------+ +--- R-Car ---------------------+ + |Oscillator|---|USB_EXTAL -+-> all usb channels| + | |---|USB_XTAL --+ | + +----------+ +-------------------------------+ +In this case, we don't need this selector. + +Required properties: +- compatible: "renesas,r8a7795-rcar-usb2-clock-sel" if the device is a part of + an R8A7795 SoC. + "renesas,r8a7796-rcar-usb2-clock-sel" if the device if a part of + an R8A7796 SoC. + "renesas,rcar-gen3-usb2-clock-sel" for a generic R-Car Gen3 + compatible device. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + +- reg: offset and length of the USB 2.0 clock selector register block. +- clocks: A list of phandles and specifier pairs. +- clock-names: Name of the clocks. + - The functional clock must be "ehci_ohci" + - The USB_EXTAL clock pin must be "usb_extal" + - The USB_XTAL clock pin must be "usb_xtal" +- #clock-cells: Must be 0 + +Example (R-Car H3): + + usb2_clksel: clock-controller@e6590630 { + compatible = "renesas,r8a77950-rcar-usb2-clock-sel", + "renesas,rcar-gen3-usb2-clock-sel"; + reg = <0 0xe6590630 0 0x02>; + clocks = <&cpg CPG_MOD 703>, <&usb_extal>, <&usb_xtal>; + clock-names = "ehci_ohci", "usb_extal", "usb_xtal"; + #clock-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3128-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3128-cru.txt index 455a9a00a623..6f8744fd301b 100644 --- a/Documentation/devicetree/bindings/clock/rockchip,rk3128-cru.txt +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3128-cru.txt @@ -1,12 +1,14 @@ -* Rockchip RK3128 Clock and Reset Unit +* Rockchip RK3126/RK3128 Clock and Reset Unit -The RK3128 clock controller generates and supplies clock to various +The RK3126/RK3128 clock controller generates and supplies clock to various controllers within the SoC and also implements a reset controller for SoC peripherals. Required Properties: -- compatible: should be "rockchip,rk3128-cru" +- compatible: should be "rockchip,rk3126-cru" or "rockchip,rk3128-cru" + "rockchip,rk3126-cru" - controller compatible with RK3126 SoC. + "rockchip,rk3128-cru" - controller compatible with RK3128 SoC. - reg: physical base address of the controller and length of memory mapped region. - #clock-cells: should be 1. diff --git a/Documentation/devicetree/bindings/clock/snps,hsdk-pll-clock.txt b/Documentation/devicetree/bindings/clock/snps,hsdk-pll-clock.txt new file mode 100644 index 000000000000..c56c7553c730 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/snps,hsdk-pll-clock.txt @@ -0,0 +1,28 @@ +Binding for the HSDK Generic PLL clock + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible: should be "snps,hsdk-<name>-pll-clock" + "snps,hsdk-core-pll-clock" + "snps,hsdk-gp-pll-clock" + "snps,hsdk-hdmi-pll-clock" +- reg : should contain base register location and length. +- clocks: shall be the input parent clock phandle for the PLL. +- #clock-cells: from common clock binding; Should always be set to 0. + +Example: + input_clk: input-clk { + clock-frequency = <33333333>; + compatible = "fixed-clock"; + #clock-cells = <0>; + }; + + cpu_clk: cpu-clk@0 { + compatible = "snps,hsdk-core-pll-clock"; + reg = <0x00 0x10>; + #clock-cells = <0>; + clocks = <&input_clk>; + }; diff --git a/Documentation/devicetree/bindings/clock/snps,pll-clock.txt b/Documentation/devicetree/bindings/clock/snps,pll-clock.txt new file mode 100644 index 000000000000..11fe4876612c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/snps,pll-clock.txt @@ -0,0 +1,28 @@ +Binding for the AXS10X Generic PLL clock + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible: should be "snps,axs10x-<name>-pll-clock" + "snps,axs10x-arc-pll-clock" + "snps,axs10x-pgu-pll-clock" +- reg: should always contain 2 pairs address - length: first for PLL config +registers and second for corresponding LOCK CGU register. +- clocks: shall be the input parent clock phandle for the PLL. +- #clock-cells: from common clock binding; Should always be set to 0. + +Example: + input-clk: input-clk { + clock-frequency = <33333333>; + compatible = "fixed-clock"; + #clock-cells = <0>; + }; + + core-clk: core-clk@80 { + compatible = "snps,axs10x-arc-pll-clock"; + reg = <0x80 0x10>, <0x100 0x10>; + #clock-cells = <0>; + clocks = <&input-clk>; + }; diff --git a/Documentation/devicetree/bindings/clock/st,stm32h7-rcc.txt b/Documentation/devicetree/bindings/clock/st,stm32h7-rcc.txt new file mode 100644 index 000000000000..a135504c7d57 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st,stm32h7-rcc.txt @@ -0,0 +1,71 @@ +STMicroelectronics STM32H7 Reset and Clock Controller +===================================================== + +The RCC IP is both a reset and a clock controller. + +Please refer to clock-bindings.txt for common clock controller binding usage. +Please also refer to reset.txt for common reset controller binding usage. + +Required properties: +- compatible: Should be: + "st,stm32h743-rcc" + +- reg: should be register base and length as documented in the + datasheet + +- #reset-cells: 1, see below + +- #clock-cells : from common clock binding; shall be set to 1 + +- clocks: External oscillator clock phandle + - high speed external clock signal (HSE) + - low speed external clock signal (LSE) + - external I2S clock (I2S_CKIN) + +Optional properties: +- st,syscfg: phandle for pwrcfg, mandatory to disable/enable backup domain + write protection (RTC clock). + +Example: + + rcc: reset-clock-controller@58024400 { + compatible = "st,stm32h743-rcc", "st,stm32-rcc"; + reg = <0x58024400 0x400>; + #reset-cells = <1>; + #clock-cells = <2>; + clocks = <&clk_hse>, <&clk_lse>, <&clk_i2s_ckin>; + + st,syscfg = <&pwrcfg>; +}; + +The peripheral clock consumer should specify the desired clock by +having the clock ID in its "clocks" phandle cell. + +Example: + + timer5: timer@40000c00 { + compatible = "st,stm32-timer"; + reg = <0x40000c00 0x400>; + interrupts = <50>; + clocks = <&rcc TIM5_CK>; + }; + +Specifying softreset control of devices +======================================= + +Device nodes should specify the reset channel required in their "resets" +property, containing a phandle to the reset device node and an index specifying +which channel to use. +The index is the bit number within the RCC registers bank, starting from RCC +base address. +It is calculated as: index = register_offset / 4 * 32 + bit_offset. +Where bit_offset is the bit offset within the register. + +For example, for CRC reset: + crc = AHB4RSTR_offset / 4 * 32 + CRCRST_bit_offset = 0x88 / 4 * 32 + 19 = 1107 + +Example: + + timer2 { + resets = <&rcc STM32H7_APB1L_RESET(TIM2)>; + }; diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt index df9fad58facd..7eda08eb8a1e 100644 --- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt +++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt @@ -3,18 +3,24 @@ Allwinner Clock Control Unit Binding Required properties : - compatible: must contain one of the following compatibles: + - "allwinner,sun4i-a10-ccu" + - "allwinner,sun5i-a10s-ccu" + - "allwinner,sun5i-a13-ccu" - "allwinner,sun6i-a31-ccu" + - "allwinner,sun7i-a20-ccu" - "allwinner,sun8i-a23-ccu" - "allwinner,sun8i-a33-ccu" - "allwinner,sun8i-a83t-ccu" - "allwinner,sun8i-a83t-r-ccu" - "allwinner,sun8i-h3-ccu" - "allwinner,sun8i-h3-r-ccu" ++ - "allwinner,sun8i-r40-ccu" - "allwinner,sun8i-v3s-ccu" - "allwinner,sun9i-a80-ccu" - "allwinner,sun50i-a64-ccu" - "allwinner,sun50i-a64-r-ccu" - "allwinner,sun50i-h5-ccu" + - "nextthing,gr8-ccu" - reg: Must contain the registers base address and length - clocks: phandle to the oscillators feeding the CCU. Two are needed: diff --git a/Documentation/devicetree/bindings/clock/uniphier-clock.txt b/Documentation/devicetree/bindings/clock/uniphier-clock.txt index 812163060fa3..7b5f602765fe 100644 --- a/Documentation/devicetree/bindings/clock/uniphier-clock.txt +++ b/Documentation/devicetree/bindings/clock/uniphier-clock.txt @@ -6,7 +6,6 @@ System clock Required properties: - compatible: should be one of the following: - "socionext,uniphier-sld3-clock" - for sLD3 SoC. "socionext,uniphier-ld4-clock" - for LD4 SoC. "socionext,uniphier-pro4-clock" - for Pro4 SoC. "socionext,uniphier-sld8-clock" - for sLD8 SoC. @@ -14,6 +13,7 @@ Required properties: "socionext,uniphier-pxs2-clock" - for PXs2/LD6b SoC. "socionext,uniphier-ld11-clock" - for LD11 SoC. "socionext,uniphier-ld20-clock" - for LD20 SoC. + "socionext,uniphier-pxs3-clock" - for PXs3 SoC - #clock-cells: should be 1. Example: @@ -48,7 +48,6 @@ Media I/O (MIO) clock, SD clock Required properties: - compatible: should be one of the following: - "socionext,uniphier-sld3-mio-clock" - for sLD3 SoC. "socionext,uniphier-ld4-mio-clock" - for LD4 SoC. "socionext,uniphier-pro4-mio-clock" - for Pro4 SoC. "socionext,uniphier-sld8-mio-clock" - for sLD8 SoC. @@ -56,6 +55,7 @@ Required properties: "socionext,uniphier-pxs2-sd-clock" - for PXs2/LD6b SoC. "socionext,uniphier-ld11-mio-clock" - for LD11 SoC. "socionext,uniphier-ld20-sd-clock" - for LD20 SoC. + "socionext,uniphier-pxs3-sd-clock" - for PXs3 SoC - #clock-cells: should be 1. Example: @@ -82,11 +82,9 @@ Provided clocks: 8: USB2 ch0 host 9: USB2 ch1 host 10: USB2 ch2 host -11: USB2 ch3 host 12: USB2 ch0 PHY 13: USB2 ch1 PHY 14: USB2 ch2 PHY -15: USB2 ch3 PHY Peripheral clock @@ -94,7 +92,6 @@ Peripheral clock Required properties: - compatible: should be one of the following: - "socionext,uniphier-sld3-peri-clock" - for sLD3 SoC. "socionext,uniphier-ld4-peri-clock" - for LD4 SoC. "socionext,uniphier-pro4-peri-clock" - for Pro4 SoC. "socionext,uniphier-sld8-peri-clock" - for sLD8 SoC. @@ -102,6 +99,7 @@ Required properties: "socionext,uniphier-pxs2-peri-clock" - for PXs2/LD6b SoC. "socionext,uniphier-ld11-peri-clock" - for LD11 SoC. "socionext,uniphier-ld20-peri-clock" - for LD20 SoC. + "socionext,uniphier-pxs3-peri-clock" - for PXs3 SoC - #clock-cells: should be 1. Example: diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt index cb7ffc58c564..b1a8929c2536 100644 --- a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt +++ b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt @@ -13,6 +13,7 @@ Required properties: - compatible : Shall contain one or more of - "renesas,r8a7795-hdmi" for R8A7795 (R-Car H3) compatible HDMI TX + - "renesas,r8a7796-hdmi" for R8A7796 (R-Car M3-W) compatible HDMI TX - "renesas,rcar-gen3-hdmi" for the generic R-Car Gen3 compatible HDMI TX When compatible with generic versions, nodes must list the SoC-specific diff --git a/Documentation/devicetree/bindings/display/renesas,du.txt b/Documentation/devicetree/bindings/display/renesas,du.txt index c6cb96a4fa93..4bbd1e9bf3be 100644 --- a/Documentation/devicetree/bindings/display/renesas,du.txt +++ b/Documentation/devicetree/bindings/display/renesas,du.txt @@ -36,8 +36,10 @@ Required Properties: When supplied they must be named "dclkin.x" with "x" being the input clock numerical index. - - vsps: A list of phandles to the VSP nodes that handle the memory - interfaces for the DU channels. + - vsps: A list of phandle and channel index tuples to the VSPs that handle + the memory interfaces for the DU channels. The phandle identifies the VSP + instance that serves the DU channel, and the channel index identifies the + LIF instance in that VSP. Required nodes: @@ -59,24 +61,24 @@ corresponding to each DU output. R8A7796 (M3-W) DPAD HDMI LVDS - -Example: R8A7790 (R-Car H2) DU +Example: R8A7795 (R-Car H3) ES2.0 DU - du: du@feb00000 { - compatible = "renesas,du-r8a7790"; - reg = <0 0xfeb00000 0 0x70000>, - <0 0xfeb90000 0 0x1c>, - <0 0xfeb94000 0 0x1c>; - reg-names = "du", "lvds.0", "lvds.1"; - interrupt-parent = <&gic>; - interrupts = <0 256 IRQ_TYPE_LEVEL_HIGH>, - <0 268 IRQ_TYPE_LEVEL_HIGH>, - <0 269 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp7_clks R8A7790_CLK_DU0>, - <&mstp7_clks R8A7790_CLK_DU1>, - <&mstp7_clks R8A7790_CLK_DU2>, - <&mstp7_clks R8A7790_CLK_LVDS0>, - <&mstp7_clks R8A7790_CLK_LVDS1>; - clock-names = "du.0", "du.1", "du.2", "lvds.0", "lvds.1"; + du: display@feb00000 { + compatible = "renesas,du-r8a7795"; + reg = <0 0xfeb00000 0 0x80000>, + <0 0xfeb90000 0 0x14>; + reg-names = "du", "lvds.0"; + interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 270 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 724>, + <&cpg CPG_MOD 723>, + <&cpg CPG_MOD 722>, + <&cpg CPG_MOD 721>, + <&cpg CPG_MOD 727>; + clock-names = "du.0", "du.1", "du.2", "du.3", "lvds.0"; + vsps = <&vspd0 0>, <&vspd1 0>, <&vspd2 0>, <&vspd0 1>; ports { #address-cells = <1>; @@ -89,12 +91,19 @@ Example: R8A7790 (R-Car H2) DU }; port@1 { reg = <1>; - du_out_lvds0: endpoint { + du_out_hdmi0: endpoint { + remote-endpoint = <&dw_hdmi0_in>; }; }; port@2 { reg = <2>; - du_out_lvds1: endpoint { + du_out_hdmi1: endpoint { + remote-endpoint = <&dw_hdmi1_in>; + }; + }; + port@3 { + reg = <3>; + du_out_lvds0: endpoint { }; }; }; diff --git a/Documentation/devicetree/bindings/dma/ti-edma.txt b/Documentation/devicetree/bindings/dma/ti-edma.txt index 33d9e386dc45..41f0c1a07c56 100644 --- a/Documentation/devicetree/bindings/dma/ti-edma.txt +++ b/Documentation/devicetree/bindings/dma/ti-edma.txt @@ -9,7 +9,12 @@ execute the actual DMA tansfer. eDMA3 Channel Controller Required properties: -- compatible: "ti,edma3-tpcc" for the channel controller(s) +-------------------- +- compatible: Should be: + - "ti,edma3-tpcc" for the channel controller(s) on OMAP, + AM33xx and AM43xx SoCs. + - "ti,k2g-edma3-tpcc", "ti,edma3-tpcc" for the + channel controller(s) on 66AK2G. - #dma-cells: Should be set to <2>. The first number is the DMA request number and the second is the TC the channel is serviced on. - reg: Memory map of eDMA CC @@ -19,8 +24,19 @@ Required properties: - ti,tptcs: List of TPTCs associated with the eDMA in the following form: <&tptc_phandle TC_priority_number>. The highest priority is 0. +SoC-specific Required properties: +-------------------------------- +The following are mandatory properties for OMAP, AM33xx and AM43xx SoCs only: +- ti,hwmods: Name of the hwmods associated to the eDMA CC. + +The following are mandatory properties for 66AK2G SoCs only: +- power-domains:Should contain a phandle to a PM domain provider node + and an args specifier containing the device id + value. This property is as per the binding, + Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt + Optional properties: -- ti,hwmods: Name of the hwmods associated to the eDMA CC +------------------- - ti,edma-memcpy-channels: List of channels allocated to be used for memcpy, iow these channels will be SW triggered channels. See example. - ti,edma-reserved-slot-ranges: PaRAM slot ranges which should not be used by @@ -31,17 +47,34 @@ Optional properties: eDMA3 Transfer Controller Required properties: -- compatible: "ti,edma3-tptc" for the transfer controller(s) +-------------------- +- compatible: Should be: + - "ti,edma3-tptc" for the transfer controller(s) on OMAP, + AM33xx and AM43xx SoCs. + - "ti,k2g-edma3-tptc", "ti,edma3-tptc" for the + transfer controller(s) on 66AK2G. - reg: Memory map of eDMA TC - interrupts: Interrupt number for TCerrint. +SoC-specific Required properties: +-------------------------------- +The following are mandatory properties for OMAP, AM33xx and AM43xx SoCs only: +- ti,hwmods: Name of the hwmods associated to the eDMA TC. + +The following are mandatory properties for 66AK2G SoCs only: +- power-domains:Should contain a phandle to a PM domain provider node + and an args specifier containing the device id + value. This property is as per the binding, + Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt + Optional properties: -- ti,hwmods: Name of the hwmods associated to the given eDMA TC +------------------- - interrupt-names: "edma3_tcerrint" ------------------------------------------------------------------------------ -Example: +Examples: +1. edma: edma@49000000 { compatible = "ti,edma3-tpcc"; ti,hwmods = "tpcc"; @@ -108,6 +141,58 @@ mcasp0: mcasp@48038000 { dma-names = "tx", "rx"; }; +2. +edma1: edma@02728000 { + compatible = "ti,k2g-edma3-tpcc", "ti,edma3-tpcc"; + reg = <0x02728000 0x8000>; + reg-names = "edma3_cc"; + interrupts = <GIC_SPI 208 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 219 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 220 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "edma3_ccint", "emda3_mperr", + "edma3_ccerrint"; + dma-requests = <64>; + #dma-cells = <2>; + + ti,tptcs = <&edma1_tptc0 7>, <&edma1_tptc1 0>; + + /* + * memcpy is disabled, can be enabled with: + * ti,edma-memcpy-channels = <12 13 14 15>; + * for example. + */ + + power-domains = <&k2g_pds 0x4f>; +}; + +edma1_tptc0: tptc@027b0000 { + compatible = "ti,k2g-edma3-tptc", "ti,edma3-tptc"; + reg = <0x027b0000 0x400>; + power-domains = <&k2g_pds 0x4f>; +}; + +edma1_tptc1: tptc@027b8000 { + compatible = "ti, k2g-edma3-tptc", "ti,edma3-tptc"; + reg = <0x027b8000 0x400>; + power-domains = <&k2g_pds 0x4f>; +}; + +mmc0: mmc@23000000 { + compatible = "ti,k2g-hsmmc", "ti,omap4-hsmmc"; + reg = <0x23000000 0x400>; + interrupts = <GIC_SPI 96 IRQ_TYPE_EDGE_RISING>; + dmas = <&edma1 24 0>, <&edma1 25 0>; + dma-names = "tx", "rx"; + bus-width = <4>; + ti,needs-special-reset; + no-1-8-v; + max-frequency = <96000000>; + power-domains = <&k2g_pds 0xb>; + clocks = <&k2g_clks 0xb 1>, <&k2g_clks 0xb 2>; + clock-names = "fck", "mmchsdb_fck"; + status = "disabled"; +}; + ------------------------------------------------------------------------------ DEPRECATED binding, new DTS files must use the ti,edma3-tpcc/ti,edma3-tptc binding. diff --git a/Documentation/devicetree/bindings/eeprom/eeprom.txt b/Documentation/devicetree/bindings/eeprom/eeprom.txt index 5696eb508e95..afc04589eadf 100644 --- a/Documentation/devicetree/bindings/eeprom/eeprom.txt +++ b/Documentation/devicetree/bindings/eeprom/eeprom.txt @@ -16,8 +16,12 @@ Required properties: "renesas,r1ex24002" + The following manufacturers values have been deprecated: + "at", "at24" + If there is no specific driver for <manufacturer>, a generic - driver based on <type> is selected. Possible types are: + device with <type> and manufacturer "atmel" should be used. + Possible types are: "24c00", "24c01", "24c02", "24c04", "24c08", "24c16", "24c32", "24c64", "24c128", "24c256", "24c512", "24c1024", "spd" diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt b/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt index 5aa5926029ee..039219df05c5 100644 --- a/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt +++ b/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt @@ -17,6 +17,7 @@ Required properties: * which must be preceded by one of the following vendor specifics: + "amlogic,meson-gxm-mali" + "rockchip,rk3288-mali" + + "rockchip,rk3399-mali" - reg : Physical base address of the device and length of the register area. diff --git a/Documentation/devicetree/bindings/i2c/i2c-altera.txt b/Documentation/devicetree/bindings/i2c/i2c-altera.txt new file mode 100644 index 000000000000..767664f448ec --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-altera.txt @@ -0,0 +1,39 @@ +* Altera I2C Controller +* This is Altera's synthesizable logic block I2C Controller for use +* in Altera's FPGAs. + +Required properties : + - compatible : should be "altr,softip-i2c-v1.0" + - reg : Offset and length of the register set for the device + - interrupts : <IRQ> where IRQ is the interrupt number. + - clocks : phandle to input clock. + - #address-cells = <1>; + - #size-cells = <0>; + +Recommended properties : + - clock-frequency : desired I2C bus clock frequency in Hz. + +Optional properties : + - fifo-size : Size of the RX and TX FIFOs in bytes. + - Child nodes conforming to i2c bus binding + +Example : + + i2c@100080000 { + compatible = "altr,softip-i2c-v1.0"; + reg = <0x00000001 0x00080000 0x00000040>; + interrupt-parent = <&intc>; + interrupts = <0 43 4>; + clocks = <&clk_0>; + clock-frequency = <100000>; + #address-cells = <1>; + #size-cells = <0>; + fifo-size = <4>; + + eeprom@51 { + compatible = "atmel,24c32"; + reg = <0x51>; + pagesize = <32>; + }; + }; + diff --git a/Documentation/devicetree/bindings/i2c/i2c-mtk.txt b/Documentation/devicetree/bindings/i2c/i2c-mtk.txt index bd5a7befd951..ff7bf37deb43 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mtk.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mtk.txt @@ -1,14 +1,15 @@ -* Mediatek's I2C controller +* MediaTek's I2C controller -The Mediatek's I2C controller is used to interface with I2C devices. +The MediaTek's I2C controller is used to interface with I2C devices. Required properties: - compatible: value should be either of the following. - "mediatek,mt2701-i2c", "mediatek,mt6577-i2c": for Mediatek mt2701 - "mediatek,mt6577-i2c": for i2c compatible with mt6577. - "mediatek,mt6589-i2c": for i2c compatible with mt6589. - "mediatek,mt7623-i2c", "mediatek,mt6577-i2c": for i2c compatible with mt7623. - "mediatek,mt8173-i2c": for i2c compatible with mt8173. + "mediatek,mt2701-i2c", "mediatek,mt6577-i2c": for MediaTek MT2701 + "mediatek,mt6577-i2c": for MediaTek MT6577 + "mediatek,mt6589-i2c": for MediaTek MT6589 + "mediatek,mt7622-i2c": for MediaTek MT7622 + "mediatek,mt7623-i2c", "mediatek,mt6577-i2c": for MediaTek MT7623 + "mediatek,mt8173-i2c": for MediaTek MT8173 - reg: physical base address of the controller and dma base, length of memory mapped region. - interrupts: interrupt number to the cpu. diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt index 2b8bd33dbf8d..cad39aee9f73 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt @@ -2,6 +2,8 @@ I2C for R-Car platforms Required properties: - compatible: + "renesas,i2c-r8a7743" if the device is a part of a R8A7743 SoC. + "renesas,i2c-r8a7745" if the device is a part of a R8A7745 SoC. "renesas,i2c-r8a7778" if the device is a part of a R8A7778 SoC. "renesas,i2c-r8a7779" if the device is a part of a R8A7779 SoC. "renesas,i2c-r8a7790" if the device is a part of a R8A7790 SoC. @@ -12,7 +14,8 @@ Required properties: "renesas,i2c-r8a7795" if the device is a part of a R8A7795 SoC. "renesas,i2c-r8a7796" if the device is a part of a R8A7796 SoC. "renesas,rcar-gen1-i2c" for a generic R-Car Gen1 compatible device. - "renesas,rcar-gen2-i2c" for a generic R-Car Gen2 compatible device. + "renesas,rcar-gen2-i2c" for a generic R-Car Gen2 or RZ/G1 compatible + device. "renesas,rcar-gen3-i2c" for a generic R-Car Gen3 compatible device. "renesas,i2c-rcar" (deprecated) diff --git a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt index e18445d0980c..22f2eeb2c4c9 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt @@ -7,6 +7,7 @@ Required properties : - reg : Offset and length of the register set for the device - compatible: should be one of the following: + - "rockchip,rv1108-i2c": for rv1108 - "rockchip,rk3066-i2c": for rk3066 - "rockchip,rk3188-i2c": for rk3188 - "rockchip,rk3228-i2c": for rk3228 diff --git a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt index ae9c2a735f39..224390999e81 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt @@ -4,6 +4,8 @@ Required properties: - compatible : - "renesas,iic-r8a73a4" (R-Mobile APE6) - "renesas,iic-r8a7740" (R-Mobile A1) + - "renesas,iic-r8a7743" (RZ/G1M) + - "renesas,iic-r8a7745" (RZ/G1E) - "renesas,iic-r8a7790" (R-Car H2) - "renesas,iic-r8a7791" (R-Car M2-W) - "renesas,iic-r8a7792" (R-Car V2H) @@ -12,7 +14,8 @@ Required properties: - "renesas,iic-r8a7795" (R-Car H3) - "renesas,iic-r8a7796" (R-Car M3-W) - "renesas,iic-sh73a0" (SH-Mobile AG5) - - "renesas,rcar-gen2-iic" (generic R-Car Gen2 compatible device) + - "renesas,rcar-gen2-iic" (generic R-Car Gen2 or RZ/G1 + compatible device) - "renesas,rcar-gen3-iic" (generic R-Car Gen3 compatible device) - "renesas,rmobile-iic" (generic device) diff --git a/Documentation/devicetree/bindings/i2c/i2c-sprd.txt b/Documentation/devicetree/bindings/i2c/i2c-sprd.txt new file mode 100644 index 000000000000..60b7cda15dd2 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-sprd.txt @@ -0,0 +1,31 @@ +I2C for Spreadtrum platforms + +Required properties: +- compatible: Should be "sprd,sc9860-i2c". +- reg: Specify the physical base address of the controller and length + of memory mapped region. +- interrupts: Should contain I2C interrupt. +- clock-names: Should contain following entries: + "i2c" for I2C clock, + "source" for I2C source (parent) clock, + "enable" for I2C module enable clock. +- clocks: Should contain a clock specifier for each entry in clock-names. +- clock-frequency: Constains desired I2C bus clock frequency in Hz. +- #address-cells: Should be 1 to describe address cells for I2C device address. +- #size-cells: Should be 0 means no size cell for I2C device address. + +Optional properties: +- Child nodes conforming to I2C bus binding + +Examples: +i2c0: i2c@70500000 { + compatible = "sprd,sc9860-i2c"; + reg = <0 0x70500000 0 0x1000>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "i2c", "source", "enable"; + clocks = <&clk_i2c3>, <&ext_26m>, <&clk_ap_apb_gates 11>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; +}; + diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt index 78eaf7b718ed..3b5489966634 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt @@ -1,7 +1,9 @@ * I2C controller embedded in STMicroelectronics STM32 I2C platform Required properties : -- compatible : Must be "st,stm32f4-i2c" +- compatible : Must be one of the following + - "st,stm32f4-i2c" + - "st,stm32f7-i2c" - reg : Offset and length of the register set for the device - interrupts : Must contain the interrupt id for I2C event and then the interrupt id for I2C error. @@ -14,8 +16,16 @@ Required properties : Optional properties : - clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, - the default 100 kHz frequency will be used. As only Normal and Fast modes - are supported, possible values are 100000 and 400000. + the default 100 kHz frequency will be used. + For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are + 100000 and 400000. + For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported, + possible values are 100000, 400000 and 1000000. +- i2c-scl-rising-time-ns : Only for STM32F7, I2C SCL Rising time for the board + (default: 25) +- i2c-scl-falling-time-ns : Only for STM32F7, I2C SCL Falling time for the board + (default: 10) + I2C Timings are derived from these 2 values Example : @@ -31,3 +41,16 @@ Example : pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>; pinctrl-names = "default"; }; + + i2c@40005400 { + compatible = "st,stm32f7-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x40005400 0x400>; + interrupts = <31>, + <32>; + resets = <&rcc STM32F7_APB1_RESET(I2C1)>; + clocks = <&rcc 1 CLK_I2C1>; + pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>; + pinctrl-names = "default"; + }; diff --git a/Documentation/devicetree/bindings/input/pwm-vibrator.txt b/Documentation/devicetree/bindings/input/pwm-vibrator.txt new file mode 100644 index 000000000000..09145d18491d --- /dev/null +++ b/Documentation/devicetree/bindings/input/pwm-vibrator.txt @@ -0,0 +1,66 @@ +* PWM vibrator device tree bindings + +Registers a PWM device as vibrator. It is expected, that the vibrator's +strength increases based on the duty cycle of the enable PWM channel +(100% duty cycle meaning strongest vibration, 0% meaning no vibration). + +The binding supports an optional direction PWM channel, that can be +driven at fixed duty cycle. If available this is can be used to increase +the vibration effect of some devices. + +Required properties: +- compatible: should contain "pwm-vibrator" +- pwm-names: Should contain "enable" and optionally "direction" +- pwms: Should contain a PWM handle for each entry in pwm-names + +Optional properties: +- vcc-supply: Phandle for the regulator supplying power +- direction-duty-cycle-ns: Duty cycle of the direction PWM channel in + nanoseconds, defaults to 50% of the channel's + period. + +Example from Motorola Droid 4: + +&omap4_pmx_core { + vibrator_direction_pin: pinmux_vibrator_direction_pin { + pinctrl-single,pins = < + OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE1) /* dmtimer8_pwm_evt (gpio_27) */ + >; + }; + + vibrator_enable_pin: pinmux_vibrator_enable_pin { + pinctrl-single,pins = < + OMAP4_IOPAD(0X1d0, PIN_OUTPUT | MUX_MODE1) /* dmtimer9_pwm_evt (gpio_28) */ + >; + }; +}; + +/ { + pwm8: dmtimer-pwm { + pinctrl-names = "default"; + pinctrl-0 = <&vibrator_direction_pin>; + + compatible = "ti,omap-dmtimer-pwm"; + #pwm-cells = <3>; + ti,timers = <&timer8>; + ti,clock-source = <0x01>; + }; + + pwm9: dmtimer-pwm { + pinctrl-names = "default"; + pinctrl-0 = <&vibrator_enable_pin>; + + compatible = "ti,omap-dmtimer-pwm"; + #pwm-cells = <3>; + ti,timers = <&timer9>; + ti,clock-source = <0x01>; + }; + + vibrator { + compatible = "pwm-vibrator"; + pwms = <&pwm8 0 1000000000 0>, + <&pwm9 0 1000000000 0>; + pwm-names = "enable", "direction"; + direction-duty-cycle-ns = <1000000000>; + }; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt index 11cc87aeb276..07bf0b9a5139 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt @@ -17,6 +17,7 @@ Required properties: "mediatek,mt6582-sysirq", "mediatek,mt6577-sysirq": for MT6582 "mediatek,mt6580-sysirq", "mediatek,mt6577-sysirq": for MT6580 "mediatek,mt6577-sysirq": for MT6577 + "mediatek,mt2712-sysirq", "mediatek,mt6577-sysirq": for MT2712 "mediatek,mt2701-sysirq", "mediatek,mt6577-sysirq": for MT2701 - interrupt-controller : Identifies the node as an interrupt controller - #interrupt-cells : Use the same format as specified by GIC in arm,gic.txt. diff --git a/Documentation/devicetree/bindings/iommu/qcom,iommu.txt b/Documentation/devicetree/bindings/iommu/qcom,iommu.txt new file mode 100644 index 000000000000..b2641ceb2b40 --- /dev/null +++ b/Documentation/devicetree/bindings/iommu/qcom,iommu.txt @@ -0,0 +1,121 @@ +* QCOM IOMMU v1 Implementation + +Qualcomm "B" family devices which are not compatible with arm-smmu have +a similar looking IOMMU but without access to the global register space, +and optionally requiring additional configuration to route context irqs +to non-secure vs secure interrupt line. + +** Required properties: + +- compatible : Should be one of: + + "qcom,msm8916-iommu" + + Followed by "qcom,msm-iommu-v1". + +- clock-names : Should be a pair of "iface" (required for IOMMUs + register group access) and "bus" (required for + the IOMMUs underlying bus access). + +- clocks : Phandles for respective clocks described by + clock-names. + +- #address-cells : must be 1. + +- #size-cells : must be 1. + +- #iommu-cells : Must be 1. Index identifies the context-bank #. + +- ranges : Base address and size of the iommu context banks. + +- qcom,iommu-secure-id : secure-id. + +- List of sub-nodes, one per translation context bank. Each sub-node + has the following required properties: + + - compatible : Should be one of: + - "qcom,msm-iommu-v1-ns" : non-secure context bank + - "qcom,msm-iommu-v1-sec" : secure context bank + - reg : Base address and size of context bank within the iommu + - interrupts : The context fault irq. + +** Optional properties: + +- reg : Base address and size of the SMMU local base, should + be only specified if the iommu requires configuration + for routing of context bank irq's to secure vs non- + secure lines. (Ie. if the iommu contains secure + context banks) + + +** Examples: + + apps_iommu: iommu@1e20000 { + #address-cells = <1>; + #size-cells = <1>; + #iommu-cells = <1>; + compatible = "qcom,msm8916-iommu", "qcom,msm-iommu-v1"; + ranges = <0 0x1e20000 0x40000>; + reg = <0x1ef0000 0x3000>; + clocks = <&gcc GCC_SMMU_CFG_CLK>, + <&gcc GCC_APSS_TCU_CLK>; + clock-names = "iface", "bus"; + qcom,iommu-secure-id = <17>; + + // mdp_0: + iommu-ctx@4000 { + compatible = "qcom,msm-iommu-v1-ns"; + reg = <0x4000 0x1000>; + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; + }; + + // venus_ns: + iommu-ctx@5000 { + compatible = "qcom,msm-iommu-v1-sec"; + reg = <0x5000 0x1000>; + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpu_iommu: iommu@1f08000 { + #address-cells = <1>; + #size-cells = <1>; + #iommu-cells = <1>; + compatible = "qcom,msm8916-iommu", "qcom,msm-iommu-v1"; + ranges = <0 0x1f08000 0x10000>; + clocks = <&gcc GCC_SMMU_CFG_CLK>, + <&gcc GCC_GFX_TCU_CLK>; + clock-names = "iface", "bus"; + qcom,iommu-secure-id = <18>; + + // gfx3d_user: + iommu-ctx@1000 { + compatible = "qcom,msm-iommu-v1-ns"; + reg = <0x1000 0x1000>; + interrupts = <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>; + }; + + // gfx3d_priv: + iommu-ctx@2000 { + compatible = "qcom,msm-iommu-v1-ns"; + reg = <0x2000 0x1000>; + interrupts = <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + ... + + venus: video-codec@1d00000 { + ... + iommus = <&apps_iommu 5>; + }; + + mdp: mdp@1a01000 { + ... + iommus = <&apps_iommu 4>; + }; + + gpu@01c00000 { + ... + iommus = <&gpu_iommu 1>, <&gpu_iommu 2>; + }; diff --git a/Documentation/devicetree/bindings/iommu/rockchip,iommu.txt b/Documentation/devicetree/bindings/iommu/rockchip,iommu.txt index 9a55ac3735e5..2098f7732264 100644 --- a/Documentation/devicetree/bindings/iommu/rockchip,iommu.txt +++ b/Documentation/devicetree/bindings/iommu/rockchip,iommu.txt @@ -15,6 +15,11 @@ Required properties: to associate with its master device. See: Documentation/devicetree/bindings/iommu/iommu.txt +Optional properties: +- rockchip,disable-mmu-reset : Don't use the mmu reset operation. + Some mmu instances may produce unexpected results + when the reset operation is used. + Example: vopl_mmu: iommu@ff940300 { diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt index 21277a56e94c..ddf46b8856a5 100644 --- a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt +++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt @@ -15,6 +15,9 @@ Required properties: the register. - "smi" : It's the clock for transfer data and command. +Required property for mt2701: +- mediatek,larb-id :the hardware id of this larb. + Example: larb1: larb@16010000 { compatible = "mediatek,mt8173-smi-larb"; @@ -25,3 +28,15 @@ Example: <&vdecsys CLK_VDEC_LARB_CKEN>; clock-names = "apb", "smi"; }; + +Example for mt2701: + larb0: larb@14010000 { + compatible = "mediatek,mt2701-smi-larb"; + reg = <0 0x14010000 0 0x1000>; + mediatek,smi = <&smi_common>; + mediatek,larb-id = <0>; + clocks = <&mmsys CLK_MM_SMI_LARB0>, + <&mmsys CLK_MM_SMI_LARB0>; + clock-names = "apb", "smi"; + power-domains = <&scpsys MT2701_POWER_DOMAIN_DISP>; + }; diff --git a/Documentation/devicetree/bindings/mips/lantiq/fpi-bus.txt b/Documentation/devicetree/bindings/mips/lantiq/fpi-bus.txt new file mode 100644 index 000000000000..0a2df4338332 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/lantiq/fpi-bus.txt @@ -0,0 +1,31 @@ +Lantiq XWAY SoC FPI BUS binding +============================ + + +------------------------------------------------------------------------------- +Required properties: +- compatible : Should be one of + "lantiq,xrx200-fpi" +- reg : The address and length of the XBAR + configuration register. + Address and length of the FPI bus itself. +- lantiq,rcu : A phandle to the RCU syscon +- lantiq,offset-endianness : Offset of the endianness configuration + register + +------------------------------------------------------------------------------- +Example for the FPI on the xrx200 SoCs: + fpi@10000000 { + compatible = "lantiq,xrx200-fpi"; + ranges = <0x0 0x10000000 0xf000000>; + reg = <0x1f400000 0x1000>, + <0x10000000 0xf000000>; + lantiq,rcu = <&rcu0>; + lantiq,offset-endianness = <0x4c>; + #address-cells = <1>; + #size-cells = <1>; + + gptu@e100a00 { + ...... + }; + }; diff --git a/Documentation/devicetree/bindings/mips/lantiq/rcu-gphy.txt b/Documentation/devicetree/bindings/mips/lantiq/rcu-gphy.txt new file mode 100644 index 000000000000..a0c19bd1ce66 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/lantiq/rcu-gphy.txt @@ -0,0 +1,36 @@ +Lantiq XWAY SoC GPHY binding +============================ + +This binding describes a software-defined ethernet PHY, provided by the RCU +module on newer Lantiq XWAY SoCs (xRX200 and newer). + +------------------------------------------------------------------------------- +Required properties: +- compatible : Should be one of + "lantiq,xrx200a1x-gphy" + "lantiq,xrx200a2x-gphy" + "lantiq,xrx300-gphy" + "lantiq,xrx330-gphy" +- reg : Addrress of the GPHY FW load address register +- resets : Must reference the RCU GPHY reset bit +- reset-names : One entry, value must be "gphy" or optional "gphy2" +- clocks : A reference to the (PMU) GPHY clock gate + +Optional properties: +- lantiq,gphy-mode : GPHY_MODE_GE (default) or GPHY_MODE_FE as defined in + <dt-bindings/mips/lantiq_xway_gphy.h> + + +------------------------------------------------------------------------------- +Example for the GPHys on the xRX200 SoCs: + +#include <dt-bindings/mips/lantiq_rcu_gphy.h> + gphy0: gphy@20 { + compatible = "lantiq,xrx200a2x-gphy"; + reg = <0x20 0x4>; + + resets = <&reset0 31 30>, <&reset1 7 7>; + reset-names = "gphy", "gphy2"; + clocks = <&pmu0 XRX200_PMU_GATE_GPHY>; + lantiq,gphy-mode = <GPHY_MODE_GE>; + }; diff --git a/Documentation/devicetree/bindings/mips/lantiq/rcu.txt b/Documentation/devicetree/bindings/mips/lantiq/rcu.txt new file mode 100644 index 000000000000..a086f1e1cdd7 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/lantiq/rcu.txt @@ -0,0 +1,89 @@ +Lantiq XWAY SoC RCU binding +=========================== + +This binding describes the RCU (reset controller unit) multifunction device, +where each sub-device has it's own set of registers. + +The RCU register range is used for multiple purposes. Mostly one device +uses one or multiple register exclusively, but for some registers some +bits are for one driver and some other bits are for a different driver. +With this patch all accesses to the RCU registers will go through +syscon. + + +------------------------------------------------------------------------------- +Required properties: +- compatible : The first and second values must be: + "lantiq,xrx200-rcu", "simple-mfd", "syscon" +- reg : The address and length of the system control registers + + +------------------------------------------------------------------------------- +Example of the RCU bindings on a xRX200 SoC: + rcu0: rcu@203000 { + compatible = "lantiq,xrx200-rcu", "simple-mfd", "syscon"; + reg = <0x203000 0x100>; + ranges = <0x0 0x203000 0x100>; + big-endian; + + gphy0: gphy@20 { + compatible = "lantiq,xrx200a2x-gphy"; + reg = <0x20 0x4>; + + resets = <&reset0 31 30>, <&reset1 7 7>; + reset-names = "gphy", "gphy2"; + lantiq,gphy-mode = <GPHY_MODE_GE>; + }; + + gphy1: gphy@68 { + compatible = "lantiq,xrx200a2x-gphy"; + reg = <0x68 0x4>; + + resets = <&reset0 29 28>, <&reset1 6 6>; + reset-names = "gphy", "gphy2"; + lantiq,gphy-mode = <GPHY_MODE_GE>; + }; + + reset0: reset-controller@10 { + compatible = "lantiq,xrx200-reset"; + reg = <0x10 4>, <0x14 4>; + + #reset-cells = <2>; + }; + + reset1: reset-controller@48 { + compatible = "lantiq,xrx200-reset"; + reg = <0x48 4>, <0x24 4>; + + #reset-cells = <2>; + }; + + usb_phy0: usb2-phy@18 { + compatible = "lantiq,xrx200-usb2-phy"; + reg = <0x18 4>, <0x38 4>; + status = "disabled"; + + resets = <&reset1 4 4>, <&reset0 4 4>; + reset-names = "phy", "ctrl"; + #phy-cells = <0>; + }; + + usb_phy1: usb2-phy@34 { + compatible = "lantiq,xrx200-usb2-phy"; + reg = <0x34 4>, <0x3C 4>; + status = "disabled"; + + resets = <&reset1 5 4>, <&reset0 4 4>; + reset-names = "phy", "ctrl"; + #phy-cells = <0>; + }; + + reboot@10 { + compatible = "syscon-reboot"; + reg = <0x10 4>; + + regmap = <&rcu0>; + offset = <0x10>; + mask = <0x40000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/mips/ni.txt b/Documentation/devicetree/bindings/mips/ni.txt new file mode 100644 index 000000000000..722bf2d62da9 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/ni.txt @@ -0,0 +1,7 @@ +National Instruments MIPS platforms + +required root node properties: + - compatible: must be "ni,169445" + +CPU Nodes + - compatible: must be "mti,mips14KEc" diff --git a/Documentation/devicetree/bindings/mips/ralink.txt b/Documentation/devicetree/bindings/mips/ralink.txt index b35a8d04f8b6..a16e8d7fe56c 100644 --- a/Documentation/devicetree/bindings/mips/ralink.txt +++ b/Documentation/devicetree/bindings/mips/ralink.txt @@ -15,3 +15,4 @@ value must be one of the following values: ralink,rt5350-soc ralink,mt7620a-soc ralink,mt7620n-soc + ralink,mt7628a-soc diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt index 0e026c151c1c..3a4ac401e6f9 100644 --- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt @@ -1,33 +1,55 @@ -* TI Highspeed MMC host controller for OMAP +* TI Highspeed MMC host controller for OMAP and 66AK2G family. -The Highspeed MMC Host Controller on TI OMAP family +The Highspeed MMC Host Controller on TI OMAP and 66AK2G family provides an interface for MMC, SD, and SDIO types of memory cards. This file documents differences between the core properties described by mmc.txt and the properties used by the omap_hsmmc driver. Required properties: +-------------------- - compatible: Should be "ti,omap2-hsmmc", for OMAP2 controllers Should be "ti,omap3-hsmmc", for OMAP3 controllers Should be "ti,omap3-pre-es3-hsmmc" for OMAP3 controllers pre ES3.0 Should be "ti,omap4-hsmmc", for OMAP4 controllers Should be "ti,am33xx-hsmmc", for AM335x controllers -- ti,hwmods: Must be "mmc<n>", n is controller instance starting 1 + Should be "ti,k2g-hsmmc", "ti,omap4-hsmmc" for 66AK2G controllers. + +SoC specific required properties: +--------------------------------- +The following are mandatory properties for OMAPs, AM33xx and AM43xx SoCs only: +- ti,hwmods: Must be "mmc<n>", n is controller instance starting 1. + +The following are mandatory properties for 66AK2G SoCs only: +- power-domains:Should contain a phandle to a PM domain provider node + and an args specifier containing the MMC device id + value. This property is as per the binding, + Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt +- clocks: Must contain an entry for each entry in clock-names. Should + be defined as per the he appropriate clock bindings consumer + usage in Documentation/devicetree/bindings/clock/ti,sci-clk.txt +- clock-names: Shall be "fck" for the functional clock, + and "mmchsdb_fck" for the debounce clock. + Optional properties: -ti,dual-volt: boolean, supports dual voltage cards -<supply-name>-supply: phandle to the regulator device tree node -"supply-name" examples are "vmmc", "vmmc_aux"(deprecated)/"vqmmc" etc -ti,non-removable: non-removable slot (like eMMC) -ti,needs-special-reset: Requires a special softreset sequence -ti,needs-special-hs-handling: HSMMC IP needs special setting for handling High Speed -dmas: List of DMA specifiers with the controller specific format -as described in the generic DMA client binding. A tx and rx -specifier is required. -dma-names: List of DMA request names. These strings correspond -1:1 with the DMA specifiers listed in dmas. The string naming is -to be "rx" and "tx" for RX and TX DMA requests, respectively. +-------------------- +- ti,dual-volt: boolean, supports dual voltage cards +- <supply-name>-supply: phandle to the regulator device tree node + "supply-name" examples are "vmmc", + "vmmc_aux"(deprecated)/"vqmmc" etc +- ti,non-removable: non-removable slot (like eMMC) +- ti,needs-special-reset: Requires a special softreset sequence +- ti,needs-special-hs-handling: HSMMC IP needs special setting + for handling High Speed +- dmas: List of DMA specifiers with the controller specific + format as described in the generic DMA client + binding. A tx and rx specifier is required. +- dma-names: List of DMA request names. These strings correspond + 1:1 with the DMA specifiers listed in dmas. + The string naming is to be "rx" and "tx" for + RX and TX DMA requests, respectively. Examples: diff --git a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt index 70dd5118a324..73d336befa08 100644 --- a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt +++ b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt @@ -1,11 +1,20 @@ * Qualcomm NAND controller Required properties: -- compatible: should be "qcom,ipq806x-nand" +- compatible: must be one of the following: + * "qcom,ipq806x-nand" - for EBI2 NAND controller being used in IPQ806x + SoC and it uses ADM DMA + * "qcom,ipq4019-nand" - for QPIC NAND controller v1.4.0 being used in + IPQ4019 SoC and it uses BAM DMA + * "qcom,ipq8074-nand" - for QPIC NAND controller v1.5.0 being used in + IPQ8074 SoC and it uses BAM DMA + - reg: MMIO address range - clocks: must contain core clock and always on clock - clock-names: must contain "core" for the core clock and "aon" for the always on clock + +EBI2 specific properties: - dmas: DMA specifier, consisting of a phandle to the ADM DMA controller node and the channel number to be used for NAND. Refer to dma.txt and qcom_adm.txt for more details @@ -16,6 +25,12 @@ Required properties: - qcom,data-crci: must contain the ADM data type CRCI block instance number specified for the NAND controller on the given platform + +QPIC specific properties: +- dmas: DMA specifier, consisting of a phandle to the BAM DMA + and the channel number to be used for NAND. Refer to + dma.txt, qcom_bam_dma.txt for more details +- dma-names: must contain all 3 channel names : "tx", "rx", "cmd" - #address-cells: <1> - subnodes give the chip-select number - #size-cells: <0> @@ -26,7 +41,6 @@ chip-selects which (may) contain NAND flash chips. Their properties are as follows. Required properties: -- compatible: should contain "qcom,nandcs" - reg: a single integer representing the chip-select number (e.g., 0, 1, 2, etc.) - #address-cells: see partition.txt @@ -43,8 +57,8 @@ partition.txt for more detail. Example: -nand@1ac00000 { - compatible = "qcom,ebi2-nandc"; +nand-controller@1ac00000 { + compatible = "qcom,ipq806x-nand"; reg = <0x1ac00000 0x800>; clocks = <&gcc EBI2_CLK>, @@ -59,8 +73,7 @@ nand@1ac00000 { #address-cells = <1>; #size-cells = <0>; - nandcs@0 { - compatible = "qcom,nandcs"; + nand@0 { reg = <0>; nand-ecc-strength = <4>; @@ -84,3 +97,43 @@ nand@1ac00000 { }; }; }; + +nand-controller@79b0000 { + compatible = "qcom,ipq4019-nand"; + reg = <0x79b0000 0x1000>; + + clocks = <&gcc GCC_QPIC_CLK>, + <&gcc GCC_QPIC_AHB_CLK>; + clock-names = "core", "aon"; + + dmas = <&qpicbam 0>, + <&qpicbam 1>, + <&qpicbam 2>; + dma-names = "tx", "rx", "cmd"; + + #address-cells = <1>; + #size-cells = <0>; + + nand@0 { + reg = <0>; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-bus-width = <8>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "boot-nand"; + reg = <0 0x58a0000>; + }; + + partition@58a0000 { + label = "fs-nand"; + reg = <0x58a0000 0x4000000>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/can/c_can.txt b/Documentation/devicetree/bindings/net/can/c_can.txt index 5a1d8b0c39e9..2d504256b0d8 100644 --- a/Documentation/devicetree/bindings/net/can/c_can.txt +++ b/Documentation/devicetree/bindings/net/can/c_can.txt @@ -11,9 +11,20 @@ Required properties: - interrupts : property with a value describing the interrupt number -Optional properties: +The following are mandatory properties for DRA7x, AM33xx and AM43xx SoCs only: - ti,hwmods : Must be "d_can<n>" or "c_can<n>", n being the instance number + +The following are mandatory properties for Keystone 2 66AK2G SoCs only: +- power-domains : Should contain a phandle to a PM domain provider node + and an args specifier containing the DCAN device id + value. This property is as per the binding, + Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt +- clocks : CAN functional clock phandle. This property is as per the + binding, + Documentation/devicetree/bindings/clock/ti,sci-clk.txt + +Optional properties: - syscon-raminit : Handle to system control region that contains the RAMINIT register, register offset to the RAMINIT register and the CAN instance number (0 offset). diff --git a/Documentation/devicetree/bindings/net/mediatek-net.txt b/Documentation/devicetree/bindings/net/mediatek-net.txt index 1d1168b805cc..214eaa9a6683 100644 --- a/Documentation/devicetree/bindings/net/mediatek-net.txt +++ b/Documentation/devicetree/bindings/net/mediatek-net.txt @@ -20,8 +20,10 @@ Required properties: "ethif", "esw", "gp0", "gp1", "gp2", "sgmii_tx250m", "sgmii_rx250m", "sgmii_cdr_ref", "sgmii_cdr_fb", "sgmii_ck", "eth2pll" : For MT7622 SoC - power-domains: phandle to the power domain that the ethernet is part of -- resets: Should contain a phandle to the ethsys reset signal -- reset-names: Should contain the reset signal name "eth" +- resets: Should contain phandles to the ethsys reset signals +- reset-names: Should contain the names of reset signal listed in the resets + property + These are "fe", "gmac" and "ppe" - mediatek,ethsys: phandle to the syscon node that handles the port setup - mediatek,sgmiisys: phandle to the syscon node that handles the SGMII setup which is required for those SoCs equipped with SGMII such as MT7622 SoC. diff --git a/Documentation/devicetree/bindings/pci/mvebu-pci.txt b/Documentation/devicetree/bindings/pci/mvebu-pci.txt index 127ae1f53e5a..6173af6885f8 100644 --- a/Documentation/devicetree/bindings/pci/mvebu-pci.txt +++ b/Documentation/devicetree/bindings/pci/mvebu-pci.txt @@ -276,7 +276,7 @@ pcie-controller { clocks = <&gateclk 26>; }; - pcie@10,0 { + pcie@a,0 { device_type = "pci"; assigned-addresses = <0x82005000 0 0x82000 0 0x2000>; reg = <0x5000 0 0 0 0>; diff --git a/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt b/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt new file mode 100644 index 000000000000..643948b6b576 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt @@ -0,0 +1,40 @@ +Lantiq XWAY SoC RCU USB 1.1/2.0 PHY binding +=========================================== + +This binding describes the USB PHY hardware provided by the RCU module on the +Lantiq XWAY SoCs. + +This node has to be a sub node of the Lantiq RCU block. + +------------------------------------------------------------------------------- +Required properties (controller (parent) node): +- compatible : Should be one of + "lantiq,ase-usb2-phy" + "lantiq,danube-usb2-phy" + "lantiq,xrx100-usb2-phy" + "lantiq,xrx200-usb2-phy" + "lantiq,xrx300-usb2-phy" +- reg : Defines the following sets of registers in the parent + syscon device + - Offset of the USB PHY configuration register + - Offset of the USB Analog configuration + register (only for xrx200 and xrx200) +- clocks : References to the (PMU) "phy" clk gate. +- clock-names : Must be "phy" +- resets : References to the RCU USB configuration reset bits. +- reset-names : Must be one of the following: + "phy" (optional) + "ctrl" (shared) + +------------------------------------------------------------------------------- +Example for the USB PHYs on an xRX200 SoC: + usb_phy0: usb2-phy@18 { + compatible = "lantiq,xrx200-usb2-phy"; + reg = <0x18 4>, <0x38 4>; + + clocks = <&pmu PMU_GATE_USB0_PHY>; + clock-names = "phy"; + resets = <&reset1 4 4>, <&reset0 4 4>; + reset-names = "phy", "ctrl"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/power/renesas,apmu.txt b/Documentation/devicetree/bindings/power/renesas,apmu.txt index 84404c9edff7..af21502e939c 100644 --- a/Documentation/devicetree/bindings/power/renesas,apmu.txt +++ b/Documentation/devicetree/bindings/power/renesas,apmu.txt @@ -1,12 +1,13 @@ DT bindings for the Renesas Advanced Power Management Unit -Renesas R-Car line of SoCs utilize one or more APMU hardware units +Renesas R-Car and RZ/G1 SoCs utilize one or more APMU hardware units for CPU core power domain control including SMP boot and CPU Hotplug. Required properties: - compatible: Should be "renesas,<soctype>-apmu", "renesas,apmu" as fallback. Examples with soctypes are: + - "renesas,r8a7743-apmu" (RZ/G1M) - "renesas,r8a7790-apmu" (R-Car H2) - "renesas,r8a7791-apmu" (R-Car M2-W) - "renesas,r8a7792-apmu" (R-Car V2H) diff --git a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt index d91715bc8d52..98cc8c09d02d 100644 --- a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt +++ b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt @@ -17,6 +17,7 @@ Required properties: - "renesas,r8a7794-sysc" (R-Car E2) - "renesas,r8a7795-sysc" (R-Car H3) - "renesas,r8a7796-sysc" (R-Car M3-W) + - "renesas,r8a77995-sysc" (R-Car D3) - reg: Address start and address range for the device. - #power-domain-cells: Must be 1. diff --git a/Documentation/devicetree/bindings/power/supply/bq24190.txt b/Documentation/devicetree/bindings/power/supply/bq24190.txt new file mode 100644 index 000000000000..9e517d307070 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq24190.txt @@ -0,0 +1,51 @@ +TI BQ24190 Li-Ion Battery Charger + +Required properties: +- compatible: contains one of the following: + * "ti,bq24190" + * "ti,bq24192i" +- reg: integer, I2C address of the charger. +- interrupts[-extended]: configuration for charger INT pin. + +Optional properties: +- monitored-battery: phandle of battery characteristics devicetree node + The charger uses the following battery properties: + + precharge-current-microamp: maximum charge current during precharge + phase (typically 20% of battery capacity). + + charge-term-current-microamp: a charge cycle terminates when the + battery voltage is above recharge threshold, and the current is below + this setting (typically 10% of battery capacity). + See also Documentation/devicetree/bindings/power/supply/battery.txt +- ti,system-minimum-microvolt: when power is connected and the battery is below + minimum system voltage, the system will be regulated above this setting. + +Notes: +- Some circuit boards wire the chip's "OTG" pin high (enabling 500mA default + charge current on USB SDP ports, among other features). To simulate this on + boards that wire the pin to a GPIO, set a gpio-hog. + +Example: + + bat: battery { + compatible = "simple-battery"; + precharge-current-microamp = <256000>; + charge-term-current-microamp = <128000>; + // etc. + }; + + bq24190: charger@6a { + compatible = "ti,bq24190"; + reg = <0x6a>; + interrupts-extended = <&gpiochip 10 IRQ_TYPE_EDGE_FALLING>; + monitored-battery = <&bat>; + ti,system-minimum-microvolt = <3200000>; + }; + + &twl_gpio { + otg { + gpio-hog; + gpios = <6 0>; + output-high; + line-name = "otg-gpio"; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/ltc2941.txt b/Documentation/devicetree/bindings/power/supply/ltc2941.txt index a9d7aa60558b..3b9ba147b041 100644 --- a/Documentation/devicetree/bindings/power/supply/ltc2941.txt +++ b/Documentation/devicetree/bindings/power/supply/ltc2941.txt @@ -1,13 +1,14 @@ -binding for LTC2941 and LTC2943 battery gauges +binding for LTC2941, LTC2942, LTC2943 and LTC2944 battery gauges -Both the LTC2941 and LTC2943 measure battery capacity. -The LTC2943 is compatible with the LTC2941, it adds voltage and -temperature monitoring, and uses a slightly different conversion -formula for the charge counter. +All chips measure battery capacity. +The LTC2942 is pin compatible with the LTC2941, it adds voltage and +temperature monitoring, and is runtime detected. LTC2943 and LTC2944 +is software compatible, uses a slightly different conversion formula +for the charge counter and adds voltage, current and temperature monitoring. Required properties: -- compatible: Should contain "lltc,ltc2941" or "lltc,ltc2943" which also - indicates the type of I2C chip attached. +- compatible: Should contain "lltc,ltc2941", "lltc,ltc2942", "lltc,ltc2943" + or "lltc,ltc2944" which also indicates the type of I2C chip attached. - reg: The 7-bit I2C address. - lltc,resistor-sense: The sense resistor value in milli-ohms. Can be a 32-bit negative value when the battery has been connected to the wrong end of the diff --git a/Documentation/devicetree/bindings/power/wakeup-source.txt b/Documentation/devicetree/bindings/power/wakeup-source.txt index 963c6dfd484d..3c81f78b5c27 100644 --- a/Documentation/devicetree/bindings/power/wakeup-source.txt +++ b/Documentation/devicetree/bindings/power/wakeup-source.txt @@ -20,13 +20,12 @@ List of legacy properties and respective binding document 1. "enable-sdio-wakeup" Documentation/devicetree/bindings/mmc/mmc.txt 2. "gpio-key,wakeup" Documentation/devicetree/bindings/input/gpio-keys{,-polled}.txt 3. "has-tpo" Documentation/devicetree/bindings/rtc/rtc-opal.txt -4. "isil,irq2-can-wakeup-machine" Documentation/devicetree/bindings/rtc/isil,isl12057.txt -5. "linux,wakeup" Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt +4. "linux,wakeup" Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt Documentation/devicetree/bindings/mfd/tc3589x.txt Documentation/devicetree/bindings/input/ads7846.txt -6. "linux,keypad-wakeup" Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt -7. "linux,input-wakeup" Documentation/devicetree/bindings/input/samsung-keypad.txt -8. "nvidia,wakeup-source" Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt +5. "linux,keypad-wakeup" Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt +6. "linux,input-wakeup" Documentation/devicetree/bindings/input/samsung-keypad.txt +7. "nvidia,wakeup-source" Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt Examples -------- diff --git a/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt b/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt index cf573e85b11d..8cf87d1bfca5 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt @@ -6,7 +6,7 @@ Required properties: - clocks: This clock defines the base clock frequency of the PWM hardware system, the period and the duty_cycle of the PWM signal is a multiple of the base period. -- #pwm-cells: Should be 2. See pwm.txt in this directory for a description of +- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of the cells format. Examples: @@ -15,7 +15,7 @@ pwm@2020c000 { compatible = "brcm,bcm2835-pwm"; reg = <0x2020c000 0x28>; clocks = <&clk_pwm>; - #pwm-cells = <2>; + #pwm-cells = <3>; }; clocks { diff --git a/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt b/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt index 54c59b0560ad..ef8bd3cb67ab 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt @@ -2,6 +2,8 @@ MediaTek PWM controller Required properties: - compatible: should be "mediatek,<name>-pwm": + - "mediatek,mt2712-pwm": found on mt2712 SoC. + - "mediatek,mt7622-pwm": found on mt7622 SoC. - "mediatek,mt7623-pwm": found on mt7623 SoC. - reg: physical base address and length of the controller's registers. - #pwm-cells: must be 2. See pwm.txt in this directory for a description of @@ -10,7 +12,9 @@ Required properties: - clock-names: must contain the following: - "top": the top clock generator - "main": clock used by the PWM core - - "pwm1-5": the five per PWM clocks + - "pwm1-8": the eight per PWM clocks for mt2712 + - "pwm1-6": the six per PWM clocks for mt7622 + - "pwm1-5": the five per PWM clocks for mt7623 - pinctrl-names: Must contain a "default" entry. - pinctrl-0: One property must exist for each entry in pinctrl-names. See pinctrl/pinctrl-bindings.txt for details of the property values. diff --git a/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt b/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt index b8be3d09ee26..2c5e52a5bede 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt @@ -3,10 +3,17 @@ Rockchip PWM controller Required properties: - compatible: should be "rockchip,<name>-pwm" "rockchip,rk2928-pwm": found on RK29XX,RK3066 and RK3188 SoCs - "rockchip,rk3288-pwm": found on RK3288 SoC + "rockchip,rk3288-pwm": found on RK3288 SOC + "rockchip,rv1108-pwm", "rockchip,rk3288-pwm": found on RV1108 SoC "rockchip,vop-pwm": found integrated in VOP on RK3288 SoC - reg: physical base address and length of the controller's registers - - clocks: phandle and clock specifier of the PWM reference clock + - clocks: See ../clock/clock-bindings.txt + - For older hardware (rk2928, rk3066, rk3188, rk3228, rk3288, rk3399): + - There is one clock that's used both to derive the functional clock + for the device and as the bus clock. + - For newer hardware (rk3328 and future socs): specified by name + - "pwm": This is used to derive the functional clock. + - "pclk": This is the APB bus clock. - #pwm-cells: must be 2 (rk2928) or 3 (rk3288). See pwm.txt in this directory for a description of the cell format. diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt index 8007e839a716..06a363d9ccef 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt @@ -6,6 +6,7 @@ Required properties: for am4372 - compatible = "ti,am4372-ecap", "ti,am3352-ecap", "ti,am33xx-ecap"; for da850 - compatible = "ti,da850-ecap", "ti,am3352-ecap", "ti,am33xx-ecap"; for dra746 - compatible = "ti,dra746-ecap", "ti,am3352-ecap"; + for 66ak2g - compatible = "ti,k2g-ecap", "ti,am3352-ecap"; - #pwm-cells: should be 3. See pwm.txt in this directory for a description of the cells format. The PWM channel index ranges from 0 to 4. The only third cell flag supported by this binding is PWM_POLARITY_INVERTED. diff --git a/Documentation/devicetree/bindings/pwm/pwm-zx.txt b/Documentation/devicetree/bindings/pwm/pwm-zx.txt new file mode 100644 index 000000000000..a6bcc75c9164 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-zx.txt @@ -0,0 +1,22 @@ +ZTE ZX PWM controller + +Required properties: + - compatible: Should be "zte,zx296718-pwm". + - reg: Physical base address and length of the controller's registers. + - clocks : The phandle and specifier referencing the controller's clocks. + - clock-names: "pclk" for PCLK, "wclk" for WCLK to the PWM controller. The + PCLK is for register access, while WCLK is the reference clock for + calculating period and duty cycles. + - #pwm-cells: Should be 3. See pwm.txt in this directory for a description of + the cells format. + +Example: + + pwm: pwm@1439000 { + compatible = "zte,zx296718-pwm"; + reg = <0x1439000 0x1000>; + clocks = <&lsp1crm LSP1_PWM_PCLK>, + <&lsp1crm LSP1_PWM_WCLK>; + clock-names = "pclk", "wclk"; + #pwm-cells = <3>; + }; diff --git a/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt b/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt index b067e84a94b5..1aadc804dae4 100644 --- a/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt @@ -6,7 +6,6 @@ Required Properties: - "renesas,tpu-r8a73a4": for R8A77A4 (R-Mobile APE6) compatible PWM controller. - "renesas,tpu-r8a7740": for R8A7740 (R-Mobile A1) compatible PWM controller. - "renesas,tpu-r8a7790": for R8A7790 (R-Car H2) compatible PWM controller. - - "renesas,tpu-sh7372": for SH7372 (SH-Mobile AP4) compatible PWM controller. - "renesas,tpu": for generic R-Car TPU PWM controller. - reg: Base address and length of each memory resource used by the PWM diff --git a/Documentation/devicetree/bindings/remoteproc/imx-rproc.txt b/Documentation/devicetree/bindings/remoteproc/imx-rproc.txt new file mode 100644 index 000000000000..fbcefd965dc4 --- /dev/null +++ b/Documentation/devicetree/bindings/remoteproc/imx-rproc.txt @@ -0,0 +1,33 @@ +NXP iMX6SX/iMX7D Co-Processor Bindings +---------------------------------------- + +This binding provides support for ARM Cortex M4 Co-processor found on some +NXP iMX SoCs. + +Required properties: +- compatible Should be one of: + "fsl,imx7d-cm4" + "fsl,imx6sx-cm4" +- clocks Clock for co-processor (See: ../clock/clock-bindings.txt) +- syscon Phandle to syscon block which provide access to + System Reset Controller + +Optional properties: +- memory-region list of phandels to the reserved memory regions. + (See: ../reserved-memory/reserved-memory.txt) + +Example: + m4_reserved_sysmem1: cm4@80000000 { + reg = <0x80000000 0x80000>; + }; + + m4_reserved_sysmem2: cm4@81000000 { + reg = <0x81000000 0x80000>; + }; + + imx7d-cm4 { + compatible = "fsl,imx7d-cm4"; + memory-region = <&m4_reserved_sysmem1>, <&m4_reserved_sysmem2>; + syscon = <&src>; + clocks = <&clks IMX7D_ARM_M4_ROOT_CLK>; + }; diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt b/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt index 75ad7b8df0b1..728e4193f7a6 100644 --- a/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt +++ b/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt @@ -63,9 +63,10 @@ on the Qualcomm ADSP Hexagon core. = SUBNODES -The adsp node may have an subnode named "smd-edge" that describes the SMD edge, -channels and devices related to the ADSP. See ../soc/qcom/qcom,smd.txt for -details on how to describe the SMD edge. +The adsp node may have an subnode named either "smd-edge" or "glink-edge" that +describes the communication edge, channels and devices related to the ADSP. +See ../soc/qcom/qcom,smd.txt and ../soc/qcom/qcom,glink.txt for details on how +to describe these. = EXAMPLE diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt index 92347fe6890e..7ff3f7903f26 100644 --- a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt +++ b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt @@ -90,6 +90,11 @@ the memory regions used by the Hexagon firmware. Each sub-node must contain: Value type: <phandle> Definition: reference to the reserved-memory for the region +The Hexagon node may also have an subnode named either "smd-edge" or +"glink-edge" that describes the communication edge, channels and devices +related to the Hexagon. See ../soc/qcom/qcom,smd.txt and +../soc/qcom/qcom,glink.txt for details on how to describe these. + = EXAMPLE The following example describes the resources needed to boot control the Hexagon, as it is found on MSM8974 boards. diff --git a/Documentation/devicetree/bindings/remoteproc/ti,davinci-rproc.txt b/Documentation/devicetree/bindings/remoteproc/ti,davinci-rproc.txt new file mode 100644 index 000000000000..e44a97e21164 --- /dev/null +++ b/Documentation/devicetree/bindings/remoteproc/ti,davinci-rproc.txt @@ -0,0 +1,86 @@ +TI Davinci DSP devices +======================= + +Binding status: Unstable - Subject to changes for DT representation of clocks + and resets + +The TI Davinci family of SoCs usually contains a TI DSP Core sub-system that +is used to offload some of the processor-intensive tasks or algorithms, for +achieving various system level goals. + +The processor cores in the sub-system usually contain additional sub-modules +like L1 and/or L2 caches/SRAMs, an Interrupt Controller, an external memory +controller, a dedicated local power/sleep controller etc. The DSP processor +core used in Davinci SoCs is usually a C674x DSP CPU. + +DSP Device Node: +================ +Each DSP Core sub-system is represented as a single DT node. + +Required properties: +-------------------- +The following are the mandatory properties: + +- compatible: Should be one of the following, + "ti,da850-dsp" for DSPs on OMAP-L138 SoCs + +- reg: Should contain an entry for each value in 'reg-names'. + Each entry should have the memory region's start address + and the size of the region, the representation matching + the parent node's '#address-cells' and '#size-cells' values. + +- reg-names: Should contain strings with the following names, each + representing a specific internal memory region or a + specific register space, + "l2sram", "l1pram", "l1dram", "host1cfg", "chipsig_base" + +- interrupts: Should contain the interrupt number used to receive the + interrupts from the DSP. The value should follow the + interrupt-specifier format as dictated by the + 'interrupt-parent' node. + +- memory-region: phandle to the reserved memory node to be associated + with the remoteproc device. The reserved memory node + can be a CMA memory node, and should be defined as + per the bindings in + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt + +Optional properties: +-------------------- +- interrupt-parent: phandle to the interrupt controller node. This property + is needed if the device node hierarchy doesn't have an + interrupt controller. + + +Example: +-------- + + /* DSP Reserved Memory node */ + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + dsp_memory_region: dsp-memory@c3000000 { + compatible = "shared-dma-pool"; + reg = <0xc3000000 0x1000000>; + reusable; + }; + }; + + /* DSP node */ + { + dsp: dsp@11800000 { + compatible = "ti,da850-dsp"; + reg = <0x11800000 0x40000>, + <0x11e00000 0x8000>, + <0x11f00000 0x8000>, + <0x01c14044 0x4>, + <0x01c14174 0x8>; + reg-names = "l2sram", "l1pram", "l1dram", "host1cfg", + "chipsig"; + interrupt-parent = <&intc>; + interrupts = <28>; + memory-region = <&dsp_memory_region>; + }; + }; diff --git a/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt b/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt index 2aac1aa4123d..1eb72874130b 100644 --- a/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt +++ b/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt @@ -26,6 +26,7 @@ The following are the mandatory properties: "ti,k2hk-dsp" for DSPs on Keystone 2 66AK2H/K SoCs "ti,k2l-dsp" for DSPs on Keystone 2 66AK2L SoCs "ti,k2e-dsp" for DSPs on Keystone 2 66AK2E SoCs + "ti,k2g-dsp" for DSPs on Keystone 2 66AK2G SoCs - reg: Should contain an entry for each value in 'reg-names'. Each entry should have the memory region's start address @@ -37,20 +38,18 @@ The following are the mandatory properties: should be defined in this order, "l2sram", "l1pram", "l1dram" -- clocks: Should contain the device's input clock, and should be - defined as per the bindings in, - Documentation/devicetree/bindings/clock/keystone-gate.txt - - ti,syscon-dev: Should be a pair of the phandle to the Keystone Device State Control node, and the register offset of the DSP boot address register within that node's address space. - resets: Should contain the phandle to the reset controller node managing the resets for this device, and a reset - specifier. Please refer to the following reset bindings - for the reset argument specifier as per SoC, + specifier. Please refer to either of the following reset + bindings for the reset argument specifier as per SoC, Documentation/devicetree/bindings/reset/ti-syscon-reset.txt - for 66AK2HK/66AK2L/66AK2E SoCs + for 66AK2HK/66AK2L/66AK2E SoCs or, + Documentation/devicetree/bindings/reset/ti,sci-reset.txt + for 66AK2G SoCs - interrupt-parent: Should contain a phandle to the Keystone 2 IRQ controller IP node that is used by the ARM CorePac processor to @@ -75,6 +74,22 @@ The following are the mandatory properties: The gpio device to be used is as per the bindings in, Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt +SoC-specific Required properties: +--------------------------------- +The following are mandatory properties for Keystone 2 66AK2HK, 66AK2L and 66AK2E +SoCs only: + +- clocks: Should contain the device's input clock, and should be + defined as per the bindings in, + Documentation/devicetree/bindings/clock/keystone-gate.txt + +The following are mandatory properties for Keystone 2 66AK2G SoCs only: + +- power-domains: Should contain a phandle to a PM domain provider node + and an args specifier containing the DSP device id + value. This property is as per the binding, + Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt + Optional properties: -------------------- @@ -85,8 +100,10 @@ Optional properties: Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt -Example: --------- +Examples: +--------- + +1. /* 66AK2H/K DSP aliases */ aliases { rproc0 = &dsp0; @@ -131,3 +148,41 @@ Example: }; }; + +2. + /* 66AK2G DSP alias */ + aliases { + rproc0 = &dsp0; + }; + + /* 66AK2G DSP memory node */ + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + dsp_common_memory: dsp-common-memory@81f800000 { + compatible = "shared-dma-pool"; + reg = <0x00000008 0x1f800000 0x00000000 0x800000>; + reusable; + }; + }; + + /* 66AK2G DSP node */ + soc { + dsp0: dsp@10800000 { + compatible = "ti,k2g-dsp"; + reg = <0x10800000 0x00100000>, + <0x10e00000 0x00008000>, + <0x10f00000 0x00008000>; + reg-names = "l2sram", "l1pram", "l1dram"; + power-domains = <&k2g_pds 0x0046>; + ti,syscon-dev = <&devctrl 0x40>; + resets = <&k2g_reset 0x0046 0x1>; + interrupt-parent = <&kirq0>; + interrupts = <0 8>; + interrupt-names = "vring", "exception"; + kick-gpios = <&dspgpio0 27 0>; + memory-region = <&dsp_common_memory>; + }; + }; diff --git a/Documentation/devicetree/bindings/reset/lantiq,reset.txt b/Documentation/devicetree/bindings/reset/lantiq,reset.txt new file mode 100644 index 000000000000..c6aef36b7d15 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/lantiq,reset.txt @@ -0,0 +1,30 @@ +Lantiq XWAY SoC RCU reset controller binding +============================================ + +This binding describes a reset-controller found on the RCU module on Lantiq +XWAY SoCs. + +This node has to be a sub node of the Lantiq RCU block. + +------------------------------------------------------------------------------- +Required properties: +- compatible : Should be one of + "lantiq,danube-reset" + "lantiq,xrx200-reset" +- reg : Defines the following sets of registers in the parent + syscon device + - Offset of the reset set register + - Offset of the reset status register +- #reset-cells : Specifies the number of cells needed to encode the + reset line, should be 2. + The first cell takes the reset set bit and the + second cell takes the status bit. + +------------------------------------------------------------------------------- +Example for the reset-controllers on the xRX200 SoCs: + reset0: reset-controller@10 { + compatible = "lantiq,xrx200-reset"; + reg <0x10 0x04>, <0x14 0x04>; + + #reset-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/reset/renesas,rst.txt b/Documentation/devicetree/bindings/reset/renesas,rst.txt index fe5e0f37b3c9..e5a03ffe04fb 100644 --- a/Documentation/devicetree/bindings/reset/renesas,rst.txt +++ b/Documentation/devicetree/bindings/reset/renesas,rst.txt @@ -26,6 +26,7 @@ Required properties: - "renesas,r8a7794-rst" (R-Car E2) - "renesas,r8a7795-rst" (R-Car H3) - "renesas,r8a7796-rst" (R-Car M3-W) + - "renesas,r8a77995-rst" (R-Car D3) - reg: Address start and address range for the device. diff --git a/Documentation/devicetree/bindings/reset/uniphier-reset.txt b/Documentation/devicetree/bindings/reset/uniphier-reset.txt index 83ab0f599c40..68a6f487c409 100644 --- a/Documentation/devicetree/bindings/reset/uniphier-reset.txt +++ b/Documentation/devicetree/bindings/reset/uniphier-reset.txt @@ -6,7 +6,6 @@ System reset Required properties: - compatible: should be one of the following: - "socionext,uniphier-sld3-reset" - for sLD3 SoC "socionext,uniphier-ld4-reset" - for LD4 SoC "socionext,uniphier-pro4-reset" - for Pro4 SoC "socionext,uniphier-sld8-reset" - for sLD8 SoC @@ -37,7 +36,6 @@ Media I/O (MIO) reset, SD reset Required properties: - compatible: should be one of the following: - "socionext,uniphier-sld3-mio-reset" - for sLD3 SoC "socionext,uniphier-ld4-mio-reset" - for LD4 SoC "socionext,uniphier-pro4-mio-reset" - for Pro4 SoC "socionext,uniphier-sld8-mio-reset" - for sLD8 SoC @@ -92,3 +90,28 @@ Example: other nodes ... }; + + +Analog signal amplifier reset +----------------------------- + +Required properties: +- compatible: should be one of the following: + "socionext,uniphier-ld11-adamv-reset" - for LD11 SoC + "socionext,uniphier-ld20-adamv-reset" - for LD20 SoC +- #reset-cells: should be 1. + +Example: + + adamv@57920000 { + compatible = "socionext,uniphier-ld11-adamv", + "simple-mfd", "syscon"; + reg = <0x57920000 0x1000>; + + adamv_rst: reset { + compatible = "socionext,uniphier-ld11-adamv-reset"; + #reset-cells = <1>; + }; + + other nodes ... + }; diff --git a/Documentation/devicetree/bindings/rtc/google,goldfish-rtc.txt b/Documentation/devicetree/bindings/rtc/google,goldfish-rtc.txt new file mode 100644 index 000000000000..634312dd95ca --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/google,goldfish-rtc.txt @@ -0,0 +1,17 @@ +Android Goldfish RTC + +Android Goldfish RTC device used by Android emulator. + +Required properties: + +- compatible : should contain "google,goldfish-rtc" +- reg : <registers mapping> +- interrupts : <interrupt mapping> + +Example: + + goldfish_timer@9020000 { + compatible = "google,goldfish-rtc"; + reg = <0x9020000 0x1000>; + interrupts = <0x3>; + }; diff --git a/Documentation/devicetree/bindings/rtc/isil,isl12057.txt b/Documentation/devicetree/bindings/rtc/isil,isl12057.txt index cf83e0940302..fbbdd92e5af9 100644 --- a/Documentation/devicetree/bindings/rtc/isil,isl12057.txt +++ b/Documentation/devicetree/bindings/rtc/isil,isl12057.txt @@ -24,7 +24,6 @@ Optional properties: - "wakeup-source": mark the chip as a wakeup source, independently of the availability of an IRQ line connected to the SoC. - (Legacy property supported: "isil,irq2-can-wakeup-machine") - "interrupt-parent", "interrupts": for passing the interrupt line of the SoC connected to IRQ#2 of the RTC chip. diff --git a/Documentation/devicetree/bindings/rtc/realtek,rtd119x.txt b/Documentation/devicetree/bindings/rtc/realtek,rtd119x.txt new file mode 100644 index 000000000000..bbf1ccb5df31 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/realtek,rtd119x.txt @@ -0,0 +1,16 @@ +Realtek RTD129x Real-Time Clock +=============================== + +Required properties: +- compatible : Should be "realtek,rtd1295-rtc" +- reg : Specifies the physical base address and size +- clocks : Specifies the clock gate + + +Example: + + rtc@9801b600 { + compatible = "realtek,rtd1295-clk"; + reg = <0x9801b600 0x100>; + clocks = <&clkc RTD1295_CLK_EN_MISC_RTC>; + }; diff --git a/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt b/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt index 945934918b71..d5e26d313f62 100644 --- a/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt @@ -10,7 +10,7 @@ Required properties: Required properties for new device trees - clocks : phandle to the 32kHz external oscillator -- clock-output-names : name of the LOSC clock created +- clock-output-names : names of the LOSC and its external output clocks created - #clock-cells : must be equals to 1. The RTC provides two clocks: the LOSC and its external output, with index 0 and 1 respectively. @@ -21,7 +21,7 @@ rtc: rtc@01f00000 { compatible = "allwinner,sun6i-a31-rtc"; reg = <0x01f00000 0x54>; interrupts = <0 40 4>, <0 41 4>; - clock-output-names = "osc32k"; + clock-output-names = "osc32k", "osc32k-out"; clocks = <&ext_osc32k>; #clock-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt index b6cf384597e1..f73abff3de43 100644 --- a/Documentation/devicetree/bindings/serial/mtk-uart.txt +++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt @@ -3,6 +3,7 @@ Required properties: - compatible should contain: * "mediatek,mt2701-uart" for MT2701 compatible UARTS + * "mediatek,mt2712-uart" for MT2712 compatible UARTS * "mediatek,mt6580-uart" for MT6580 compatible UARTS * "mediatek,mt6582-uart" for MT6582 compatible UARTS * "mediatek,mt6589-uart" for MT6589 compatible UARTS diff --git a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt index b1d165b4d4b3..40056f7990f8 100644 --- a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt +++ b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt @@ -12,11 +12,13 @@ power/power_domain.txt. It provides the power domains defined in - include/dt-bindings/power/mt8173-power.h - include/dt-bindings/power/mt6797-power.h - include/dt-bindings/power/mt2701-power.h +- include/dt-bindings/power/mt7622-power.h Required properties: - compatible: Should be one of: - "mediatek,mt2701-scpsys" - "mediatek,mt6797-scpsys" + - "mediatek,mt7622-scpsys" - "mediatek,mt8173-scpsys" - #power-domain-cells: Must be 1 - reg: Address range of the SCPSYS unit @@ -26,6 +28,7 @@ Required properties: enabled before enabling certain power domains. Required clocks for MT2701: "mm", "mfg", "ethif" Required clocks for MT6797: "mm", "mfg", "vdec" + Required clocks for MT7622: "hif_sel" Required clocks for MT8173: "mm", "mfg", "venc", "venc_lt" Optional properties: diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt index 50fc20c6ce91..b277eca861f7 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt @@ -1,11 +1,12 @@ -Qualcomm RPM GLINK binding +Qualcomm GLINK edge binding -This binding describes the Qualcomm RPM GLINK, a fifo based mechanism for -communication with the Resource Power Management system on various Qualcomm -platforms. +This binding describes a Qualcomm GLINK edge, a fifo based mechanism for +communication between subsystem-pairs on various Qualcomm platforms. Two types +of edges can be described by the binding; the GLINK RPM edge and a SMEM based +edge. - compatible: - Usage: required + Usage: required for glink-rpm Value type: <stringlist> Definition: must be "qcom,glink-rpm" @@ -16,7 +17,7 @@ platforms. signal this processor about communication related events - qcom,rpm-msg-ram: - Usage: required + Usage: required for glink-rpm Value type: <prop-encoded-array> Definition: handle to RPM message memory resource diff --git a/Documentation/devicetree/bindings/soc/rockchip/grf.txt b/Documentation/devicetree/bindings/soc/rockchip/grf.txt index cc9f05d3cbc1..7dc5ce858a0e 100644 --- a/Documentation/devicetree/bindings/soc/rockchip/grf.txt +++ b/Documentation/devicetree/bindings/soc/rockchip/grf.txt @@ -21,6 +21,7 @@ Required Properties: - "rockchip,rk3328-grf", "syscon": for rk3328 - "rockchip,rk3368-grf", "syscon": for rk3368 - "rockchip,rk3399-grf", "syscon": for rk3399 + - "rockchip,rv1108-grf", "syscon": for rv1108 - compatible: PMUGRF should be one of the following: - "rockchip,rk3368-pmugrf", "syscon": for rk3368 - "rockchip,rk3399-pmugrf", "syscon": for rk3399 @@ -28,6 +29,8 @@ Required Properties: - "rockchip,rk3288-sgrf", "syscon": for rk3288 - compatible: USB2PHYGRF should be one of the followings - "rockchip,rk3328-usb2phy-grf", "syscon": for rk3328 +- compatible: USBGRF should be one of the following + - "rockchip,rv1108-usbgrf", "syscon": for rv1108 - reg: physical base address of the controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt b/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt index 01bfb6745fbd..301d2a9bc1b8 100644 --- a/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt +++ b/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt @@ -7,6 +7,7 @@ Required properties for power domain controller: - compatible: Should be one of the following. "rockchip,rk3288-power-controller" - for RK3288 SoCs. "rockchip,rk3328-power-controller" - for RK3328 SoCs. + "rockchip,rk3366-power-controller" - for RK3366 SoCs. "rockchip,rk3368-power-controller" - for RK3368 SoCs. "rockchip,rk3399-power-controller" - for RK3399 SoCs. - #power-domain-cells: Number of cells in a power-domain specifier. @@ -18,6 +19,7 @@ Required properties for power domain sub nodes: - reg: index of the power domain, should use macros in: "include/dt-bindings/power/rk3288-power.h" - for RK3288 type power domain. "include/dt-bindings/power/rk3328-power.h" - for RK3328 type power domain. + "include/dt-bindings/power/rk3366-power.h" - for RK3366 type power domain. "include/dt-bindings/power/rk3368-power.h" - for RK3368 type power domain. "include/dt-bindings/power/rk3399-power.h" - for RK3399 type power domain. - clocks (optional): phandles to clocks which need to be enabled while power domain @@ -93,6 +95,7 @@ power domain to use. The index should use macros in: "include/dt-bindings/power/rk3288-power.h" - for rk3288 type power domain. "include/dt-bindings/power/rk3328-power.h" - for rk3328 type power domain. + "include/dt-bindings/power/rk3366-power.h" - for rk3366 type power domain. "include/dt-bindings/power/rk3368-power.h" - for rk3368 type power domain. "include/dt-bindings/power/rk3399-power.h" - for rk3399 type power domain. diff --git a/Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt b/Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt index c705db07d820..66e6265fb0aa 100644 --- a/Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt +++ b/Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt @@ -46,12 +46,13 @@ Required Properties: - power-domains: phandle pointing to the corresponding PM domain node and an ID representing the device. -See dt-bindings/genpd/k2g.h for the list of valid identifiers for k2g. +See http://processors.wiki.ti.com/index.php/TISCI#66AK2G02_Data for the list +of valid identifiers for k2g. Example (K2G): -------------------- uart0: serial@02530c00 { compatible = "ns16550a"; ... - power-domains = <&k2g_pds K2G_DEV_UART0>; + power-domains = <&k2g_pds 0x002c>; }; diff --git a/Documentation/devicetree/bindings/sound/atmel-classd.txt b/Documentation/devicetree/bindings/sound/atmel-classd.txt index 549e701cb7a1..898551076382 100644 --- a/Documentation/devicetree/bindings/sound/atmel-classd.txt +++ b/Documentation/devicetree/bindings/sound/atmel-classd.txt @@ -13,13 +13,11 @@ Required properties: Must be "tx". - clock-names Tuple listing input clock names. - Required elements: "pclk", "gclk" and "aclk". + Required elements: "pclk" and "gclk". - clocks Please refer to clock-bindings.txt. - assigned-clocks Should be <&classd_gclk>. -- assigned-clock-parents - Should be <&audio_pll_pmc>. Optional properties: - pinctrl-names, pinctrl-0 @@ -45,10 +43,9 @@ classd: classd@fc048000 { (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(47))>; dma-names = "tx"; - clocks = <&classd_clk>, <&classd_gclk>, <&audio_pll_pmc>; - clock-names = "pclk", "gclk", "aclk"; + clocks = <&classd_clk>, <&classd_gclk>; + clock-names = "pclk", "gclk"; assigned-clocks = <&classd_gclk>; - assigned-clock-parents = <&audio_pll_pmc>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_classd_default>; diff --git a/Documentation/devicetree/bindings/sram/renesas,smp-sram.txt b/Documentation/devicetree/bindings/sram/renesas,smp-sram.txt new file mode 100644 index 000000000000..712d05e3e15e --- /dev/null +++ b/Documentation/devicetree/bindings/sram/renesas,smp-sram.txt @@ -0,0 +1,27 @@ +* Renesas SMP SRAM + +Renesas R-Car Gen2 and RZ/G1 SoCs need a small piece of SRAM for the jump stub +for secondary CPU bringup and CPU hotplug. +This memory is reserved by adding a child node to a "mmio-sram" node, cfr. +Documentation/devicetree/bindings/sram/sram.txt. + +Required child node properties: + - compatible: Must be "renesas,smp-sram", + - reg: Address and length of the reserved SRAM. + The full physical (bus) address must be aligned to a 256 KiB boundary. + + +Example: + + icram1: sram@e63c0000 { + compatible = "mmio-sram"; + reg = <0 0xe63c0000 0 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0xe63c0000 0x1000>; + + smp-sram@0 { + compatible = "renesas,smp-sram"; + reg = <0 0x10>; + }; + }; diff --git a/Documentation/devicetree/bindings/sram/sunxi-sram.txt b/Documentation/devicetree/bindings/sram/sunxi-sram.txt index 170034e6c8b0..6bb92a1df753 100644 --- a/Documentation/devicetree/bindings/sram/sunxi-sram.txt +++ b/Documentation/devicetree/bindings/sram/sunxi-sram.txt @@ -9,7 +9,9 @@ Controller Node --------------- Required properties: -- compatible : "allwinner,sun4i-a10-sram-controller" +- compatible : should be: + - "allwinner,sun4i-a10-sram-controller" + - "allwinner,sun50i-a64-sram-controller" - reg : sram controller register offset + length SRAM nodes @@ -22,10 +24,13 @@ Each SRAM will have SRAM sections that are going to be handled by the SRAM controller as subnodes. These sections are represented following once again the representation described in the mmio-sram binding. -The valid sections compatible are: +The valid sections compatible for A10 are: - allwinner,sun4i-a10-sram-a3-a4 - allwinner,sun4i-a10-sram-d +The valid sections compatible for A64 are: + - allwinner,sun50i-a64-sram-c + Devices using SRAM sections --------------------------- diff --git a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt index e2f494d74d8a..0d73ea5e9c0c 100644 --- a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt @@ -11,6 +11,7 @@ Required properties: - compatible: - "mediatek,mt8173-thermal" : For MT8173 family of SoCs - "mediatek,mt2701-thermal" : For MT2701 family of SoCs + - "mediatek,mt2712-thermal" : For MT2712 family of SoCs - reg: Address range of the thermal controller - interrupts: IRQ for the thermal controller - clocks, clock-names: Clocks needed for the thermal controller. required diff --git a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt index 43003aec94bd..e3a6234fb1ac 100644 --- a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt @@ -4,6 +4,7 @@ Required properties: - compatible : should be "rockchip,<name>-tsadc" "rockchip,rk3228-tsadc": found on RK3228 SoCs "rockchip,rk3288-tsadc": found on RK3288 SoCs + "rockchip,rk3328-tsadc": found on RK3328 SoCs "rockchip,rk3368-tsadc": found on RK3368 SoCs "rockchip,rk3399-tsadc": found on RK3399 SoCs - reg : physical base address of the controller and length of memory mapped diff --git a/Documentation/devicetree/bindings/thermal/uniphier-thermal.txt b/Documentation/devicetree/bindings/thermal/uniphier-thermal.txt new file mode 100644 index 000000000000..686c0b42ed3f --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/uniphier-thermal.txt @@ -0,0 +1,64 @@ +* UniPhier Thermal bindings + +This describes the devicetree bindings for thermal monitor supported by +PVT(Process, Voltage and Temperature) monitoring unit implemented on Socionext +UniPhier SoCs. + +Required properties: +- compatible : + - "socionext,uniphier-pxs2-thermal" : For UniPhier PXs2 SoC + - "socionext,uniphier-ld20-thermal" : For UniPhier LD20 SoC +- interrupts : IRQ for the temperature alarm +- #thermal-sensor-cells : Should be 0. See ./thermal.txt for details. + +Optional properties: +- socionext,tmod-calibration: A pair of calibrated values referred from PVT, + in case that the values aren't set on SoC, + like a reference board. + +Example: + + sysctrl@61840000 { + compatible = "socionext,uniphier-ld20-sysctrl", + "simple-mfd", "syscon"; + reg = <0x61840000 0x10000>; + ... + pvtctl: pvtctl { + compatible = "socionext,uniphier-ld20-thermal"; + interrupts = <0 3 1>; + #thermal-sensor-cells = <0>; + }; + ... + }; + + thermal-zones { + cpu_thermal { + polling-delay-passive = <250>; /* 250ms */ + polling-delay = <1000>; /* 1000ms */ + thermal-sensors = <&pvtctl>; + + trips { + cpu_crit: cpu_crit { + temperature = <110000>; /* 110C */ + hysteresis = <2000>; + type = "critical"; + }; + cpu_alert: cpu_alert { + temperature = <100000>; /* 100C */ + hysteresis = <2000>; + type = "passive"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu_alert>; + cooling-device = <&cpu0 (-1) (-1)>; + }; + map1 { + trip = <&cpu_alert>; + cooling-device = <&cpu2 (-1) (-1)>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 5a79aeb620b3..1ea1fd4232ab 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -48,6 +48,7 @@ avic Shanghai AVIC Optoelectronics Co., Ltd. axentia Axentia Technologies AB axis Axis Communications AB bananapi BIPAI KEJI LIMITED +bhf Beckhoff Automation GmbH & Co. KG boe BOE Technology Group Co., Ltd. bosch Bosch Sensortec GmbH boundary Boundary Devices Inc. @@ -360,6 +361,7 @@ variscite Variscite Ltd. via VIA Technologies, Inc. virtio Virtual I/O Device Specification, developed by the OASIS consortium vivante Vivante Corporation +vocore VoCore Studio voipac Voipac Technologies s.r.o. wd Western Digital Corp. wetek WeTek Electronics, limited. diff --git a/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt b/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt index c5e74d7b4406..c5077a1f5cb3 100644 --- a/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt @@ -8,9 +8,49 @@ Required properties: - reg: physical base address of the controller and length of memory mapped region +Optional properties: + + - aspeed,reset-type = "cpu|soc|system|none" + + Reset behavior - Whenever a timeout occurs the watchdog can be programmed + to generate one of three different, mutually exclusive, types of resets. + + Type "none" can be specified to indicate that no resets are to be done. + This is useful in situations where another watchdog engine on chip is + to perform the reset. + + If 'aspeed,reset-type=' is not specfied the default is to enable system + reset. + + Reset types: + + - cpu: Reset CPU on watchdog timeout + + - soc: Reset 'System on Chip' on watchdog timeout + + - system: Reset system on watchdog timeout + + - none: No reset is performed on timeout. Assumes another watchdog + engine is responsible for this. + + - aspeed,alt-boot: If property is present then boot from alternate block. + - aspeed,external-signal: If property is present then signal is sent to + external reset counter (only WDT1 and WDT2). If not + specified no external signal is sent. + - aspeed,ext-pulse-duration: External signal pulse duration in microseconds + +Optional properties for AST2500-compatible watchdogs: + - aspeed,ext-push-pull: If aspeed,external-signal is present, set the pin's + drive type to push-pull. The default is open-drain. + - aspeed,ext-active-high: If aspeed,external-signal is present and and the pin + is configured as push-pull, then set the pulse + polarity to active-high. The default is active-low. + Example: wdt1: watchdog@1e785000 { compatible = "aspeed,ast2400-wdt"; reg = <0x1e785000 0x1c>; + aspeed,reset-type = "system"; + aspeed,external-signal; }; diff --git a/Documentation/devicetree/bindings/watchdog/lantiq-wdt.txt b/Documentation/devicetree/bindings/watchdog/lantiq-wdt.txt new file mode 100644 index 000000000000..18d4d8302702 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/lantiq-wdt.txt @@ -0,0 +1,24 @@ +Lantiq WTD watchdog binding +============================ + +This describes the binding of the Lantiq watchdog driver. + +------------------------------------------------------------------------------- +Required properties: +- compatible : Should be one of + "lantiq,wdt" + "lantiq,xrx100-wdt" + "lantiq,xrx200-wdt", "lantiq,xrx100-wdt" + "lantiq,falcon-wdt" +- reg : Address of the watchdog block +- lantiq,rcu : A phandle to the RCU syscon (required for + "lantiq,falcon-wdt" and "lantiq,xrx100-wdt") + +------------------------------------------------------------------------------- +Example for the watchdog on the xRX200 SoCs: + watchdog@803f0 { + compatible = "lantiq,xrx200-wdt", "lantiq,xrx100-wdt"; + reg = <0x803f0 0x10>; + + lantiq,rcu = <&rcu0>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/meson-wdt.txt b/Documentation/devicetree/bindings/watchdog/meson-wdt.txt index ae70185d96e6..8a6d84cb36c9 100644 --- a/Documentation/devicetree/bindings/watchdog/meson-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/meson-wdt.txt @@ -2,7 +2,11 @@ Meson SoCs Watchdog timer Required properties: -- compatible : should be "amlogic,meson6-wdt" or "amlogic,meson8b-wdt" +- compatible : depending on the SoC this should be one of: + "amlogic,meson6-wdt" on Meson6 SoCs + "amlogic,meson8-wdt" and "amlogic,meson6-wdt" on Meson8 SoCs + "amlogic,meson8b-wdt" on Meson8b SoCs + "amlogic,meson8m2-wdt" and "amlogic,meson8b-wdt" on Meson8m2 SoCs - reg : Specifies base physical address and size of the registers. Example: diff --git a/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt b/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt index 6a00939a059a..235de0683bb6 100644 --- a/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt @@ -3,9 +3,11 @@ Mediatek SoCs Watchdog timer Required properties: - compatible should contain: - * "mediatek,mt2701-wdt" for MT2701 compatible watchdog timers - * "mediatek,mt6589-wdt" for all compatible watchdog timers (MT2701, - MT6589) + "mediatek,mt2701-wdt", "mediatek,mt6589-wdt": for MT2701 + "mediatek,mt6589-wdt": for MT6589 + "mediatek,mt6797-wdt", "mediatek,mt6589-wdt": for MT6797 + "mediatek,mt7622-wdt", "mediatek,mt6589-wdt": for MT7622 + "mediatek,mt7623-wdt", "mediatek,mt6589-wdt": for MT7623 - reg : Specifies base physical address and size of the registers. diff --git a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt index 9e306afbbd49..bf6d1ca58af7 100644 --- a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt @@ -6,6 +6,7 @@ Required properties: Examples with soctypes are: - "renesas,r8a7795-wdt" (R-Car H3) - "renesas,r8a7796-wdt" (R-Car M3-W) + - "renesas,r8a77995-wdt" (R-Car D3) - "renesas,r7s72100-wdt" (RZ/A1) When compatible with the generic version, nodes must list the SoC-specific |