diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
64 files changed, 1342 insertions, 84 deletions
diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt index 973884a1bacf..1dfee20eee74 100644 --- a/Documentation/devicetree/bindings/arm/amlogic.txt +++ b/Documentation/devicetree/bindings/arm/amlogic.txt @@ -9,6 +9,12 @@ Boards with the Amlogic Meson8 SoC shall have the following properties: Required root node property: compatible: "amlogic,meson8"; +Boards with the Amlogic Meson8b SoC shall have the following properties: + Required root node property: + compatible: "amlogic,meson8b"; + Board compatible values: - - "geniatech,atv1200" - - "minix,neo-x8" + - "geniatech,atv1200" (Meson6) + - "minix,neo-x8" (Meson8) + - "tronfy,mxq" (Meson8b) + - "hardkernel,odroid-c1" (Meson8b) diff --git a/Documentation/devicetree/bindings/arm/apm/scu.txt b/Documentation/devicetree/bindings/arm/apm/scu.txt new file mode 100644 index 000000000000..b45be06625fd --- /dev/null +++ b/Documentation/devicetree/bindings/arm/apm/scu.txt @@ -0,0 +1,17 @@ +APM X-GENE SoC series SCU Registers + +This system clock unit contain various register that control block resets, +clock enable/disables, clock divisors and other deepsleep registers. + +Properties: + - compatible : should contain two values. First value must be: + - "apm,xgene-scu" + second value must be always "syscon". + + - reg : offset and length of the register set. + +Example : + scu: system-clk-controller@17000000 { + compatible = "apm,xgene-scu","syscon"; + reg = <0x0 0x17000000 0x0 0x400>; + }; diff --git a/Documentation/devicetree/bindings/arm/arm,scpi.txt b/Documentation/devicetree/bindings/arm/arm,scpi.txt new file mode 100644 index 000000000000..86302de67c2c --- /dev/null +++ b/Documentation/devicetree/bindings/arm/arm,scpi.txt @@ -0,0 +1,188 @@ +System Control and Power Interface (SCPI) Message Protocol +---------------------------------------------------------- + +Firmware implementing the SCPI described in ARM document number ARM DUI 0922B +("ARM Compute Subsystem SCP: Message Interface Protocols")[0] can be used +by Linux to initiate various system control and power operations. + +Required properties: + +- compatible : should be "arm,scpi" +- mboxes: List of phandle and mailbox channel specifiers + All the channels reserved by remote SCP firmware for use by + SCPI message protocol should be specified in any order +- shmem : List of phandle pointing to the shared memory(SHM) area between the + processors using these mailboxes for IPC, one for each mailbox + SHM can be any memory reserved for the purpose of this communication + between the processors. + +See Documentation/devicetree/bindings/mailbox/mailbox.txt +for more details about the generic mailbox controller and +client driver bindings. + +Clock bindings for the clocks based on SCPI Message Protocol +------------------------------------------------------------ + +This binding uses the common clock binding[1]. + +Container Node +============== +Required properties: +- compatible : should be "arm,scpi-clocks" + All the clocks provided by SCP firmware via SCPI message + protocol much be listed as sub-nodes under this node. + +Sub-nodes +========= +Required properties: +- compatible : shall include one of the following + "arm,scpi-dvfs-clocks" - all the clocks that are variable and index based. + These clocks don't provide an entire range of values between the + limits but only discrete points within the range. The firmware + provides the mapping for each such operating frequency and the + index associated with it. The firmware also manages the + voltage scaling appropriately with the clock scaling. + "arm,scpi-variable-clocks" - all the clocks that are variable and provide full + range within the specified range. The firmware provides the + range of values within a specified range. + +Other required properties for all clocks(all from common clock binding): +- #clock-cells : Should be 1. Contains the Clock ID value used by SCPI commands. +- clock-output-names : shall be the corresponding names of the outputs. +- clock-indices: The identifying number for the clocks(i.e.clock_id) in the + node. It can be non linear and hence provide the mapping of identifiers + into the clock-output-names array. + +SRAM and Shared Memory for SCPI +------------------------------- + +A small area of SRAM is reserved for SCPI communication between application +processors and SCP. + +Required properties: +- compatible : should be "arm,juno-sram-ns" for Non-secure SRAM on Juno + +The rest of the properties should follow the generic mmio-sram description +found in ../../misc/sysram.txt + +Each sub-node represents the reserved area for SCPI. + +Required sub-node properties: +- reg : The base offset and size of the reserved area with the SRAM +- compatible : should be "arm,juno-scp-shmem" for Non-secure SRAM based + shared memory on Juno platforms + +Sensor bindings for the sensors based on SCPI Message Protocol +-------------------------------------------------------------- +SCPI provides an API to access the various sensors on the SoC. + +Required properties: +- compatible : should be "arm,scpi-sensors". +- #thermal-sensor-cells: should be set to 1. This property follows the + thermal device tree bindings[2]. + + Valid cell values are raw identifiers (Sensor + ID) as used by the firmware. Refer to + platform documentation for your + implementation for the IDs to use. For Juno + R0 and Juno R1 refer to [3]. + +[0] http://infocenter.arm.com/help/topic/com.arm.doc.dui0922b/index.html +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/thermal/thermal.txt +[3] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dui0922b/apas03s22.html + +Example: + +sram: sram@50000000 { + compatible = "arm,juno-sram-ns", "mmio-sram"; + reg = <0x0 0x50000000 0x0 0x10000>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x0 0x50000000 0x10000>; + + cpu_scp_lpri: scp-shmem@0 { + compatible = "arm,juno-scp-shmem"; + reg = <0x0 0x200>; + }; + + cpu_scp_hpri: scp-shmem@200 { + compatible = "arm,juno-scp-shmem"; + reg = <0x200 0x200>; + }; +}; + +mailbox: mailbox0@40000000 { + .... + #mbox-cells = <1>; +}; + +scpi_protocol: scpi@2e000000 { + compatible = "arm,scpi"; + mboxes = <&mailbox 0 &mailbox 1>; + shmem = <&cpu_scp_lpri &cpu_scp_hpri>; + + clocks { + compatible = "arm,scpi-clocks"; + + scpi_dvfs: scpi_clocks@0 { + compatible = "arm,scpi-dvfs-clocks"; + #clock-cells = <1>; + clock-indices = <0>, <1>, <2>; + clock-output-names = "atlclk", "aplclk","gpuclk"; + }; + scpi_clk: scpi_clocks@3 { + compatible = "arm,scpi-variable-clocks"; + #clock-cells = <1>; + clock-indices = <3>, <4>; + clock-output-names = "pxlclk0", "pxlclk1"; + }; + }; + + scpi_sensors0: sensors { + compatible = "arm,scpi-sensors"; + #thermal-sensor-cells = <1>; + }; +}; + +cpu@0 { + ... + reg = <0 0>; + clocks = <&scpi_dvfs 0>; +}; + +hdlcd@7ff60000 { + ... + reg = <0 0x7ff60000 0 0x1000>; + clocks = <&scpi_clk 4>; +}; + +thermal-zones { + soc_thermal { + polling-delay-passive = <100>; + polling-delay = <1000>; + + /* sensor ID */ + thermal-sensors = <&scpi_sensors0 3>; + ... + }; +}; + +In the above example, the #clock-cells is set to 1 as required. +scpi_dvfs has 3 output clocks namely: atlclk, aplclk, and gpuclk with 0, +1 and 2 as clock-indices. scpi_clk has 2 output clocks namely: pxlclk0 +and pxlclk1 with 3 and 4 as clock-indices. + +The first consumer in the example is cpu@0 and it has '0' as the clock +specifier which points to the first entry in the output clocks of +scpi_dvfs i.e. "atlclk". + +Similarly the second example is hdlcd@7ff60000 and it has pxlclk1 as input +clock. '4' in the clock specifier here points to the second entry +in the output clocks of scpi_clocks i.e. "pxlclk1" + +The thermal-sensors property in the soc_thermal node uses the +temperature sensor provided by SCP firmware to setup a thermal +zone. The ID "3" is the sensor identifier for the temperature sensor +as used by the firmware. diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt index 430608ec09f0..0d0c1ae81bed 100644 --- a/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt @@ -20,6 +20,25 @@ system control is required: - compatible: "brcm,bcm<chip_id>-hif-cpubiuctrl", "syscon" - compatible: "brcm,bcm<chip_id>-hif-continuation", "syscon" +hif-cpubiuctrl node +------------------- +SoCs with Broadcom Brahma15 ARM-based CPUs have a specific Bus Interface Unit +(BIU) block which controls and interfaces the CPU complex to the different +Memory Controller Ports (MCP), one per memory controller (MEMC). This BIU block +offers a feature called Write Pairing which consists in collapsing two adjacent +cache lines into a single (bursted) write transaction towards the memory +controller (MEMC) to maximize write bandwidth. + +Required properties: + + - compatible: must be "brcm,bcm7445-hif-cpubiuctrl", "syscon" + +Optional properties: + + - brcm,write-pairing: + Boolean property, which when present indicates that the chip + supports write-pairing. + example: rdb { #address-cells = <1>; @@ -35,6 +54,7 @@ example: hif_cpubiuctrl: syscon@3e2400 { compatible = "brcm,bcm7445-hif-cpubiuctrl", "syscon"; reg = <0x3e2400 0x5b4>; + brcm,write-pairing; }; hif_continuation: syscon@452000 { @@ -43,8 +63,7 @@ example: }; }; -Lastly, nodes that allow for support of SMP initialization and reboot are -required: +Nodes that allow for support of SMP initialization and reboot are required: smpboot ------- @@ -95,3 +114,142 @@ example: compatible = "brcm,brcmstb-reboot"; syscon = <&sun_top_ctrl 0x304 0x308>; }; + + + +Power management +---------------- + +For power management (particularly, S2/S3/S5 system suspend), the following SoC +components are needed: + += Always-On control block (AON CTRL) + +This hardware provides control registers for the "always-on" (even in low-power +modes) hardware, such as the Power Management State Machine (PMSM). + +Required properties: +- compatible : should contain "brcm,brcmstb-aon-ctrl" +- reg : the register start and length for the AON CTRL block + +Example: + +aon-ctrl@410000 { + compatible = "brcm,brcmstb-aon-ctrl"; + reg = <0x410000 0x400>; +}; + += Memory controllers + +A Broadcom STB SoC typically has a number of independent memory controllers, +each of which may have several associated hardware blocks, which are versioned +independently (control registers, DDR PHYs, etc.). One might consider +describing these controllers as a parent "memory controllers" block, which +contains N sub-nodes (one for each controller in the system), each of which is +associated with a number of hardware register resources (e.g., its PHY). See +the example device tree snippet below. + +== MEMC (MEMory Controller) + +Represents a single memory controller instance. + +Required properties: +- compatible : should contain "brcm,brcmstb-memc" and "simple-bus" + +Should contain subnodes for any of the following relevant hardware resources: + +== DDR PHY control + +Control registers for this memory controller's DDR PHY. + +Required properties: +- compatible : should contain one of these + "brcm,brcmstb-ddr-phy-v225.1" + "brcm,brcmstb-ddr-phy-v240.1" + "brcm,brcmstb-ddr-phy-v240.2" + +- reg : the DDR PHY register range + +== DDR SHIMPHY + +Control registers for this memory controller's DDR SHIMPHY. + +Required properties: +- compatible : should contain "brcm,brcmstb-ddr-shimphy-v1.0" +- reg : the DDR SHIMPHY register range + +== MEMC DDR control + +Sequencer DRAM parameters and control registers. Used for Self-Refresh +Power-Down (SRPD), among other things. + +Required properties: +- compatible : should contain "brcm,brcmstb-memc-ddr" +- reg : the MEMC DDR register range + +Example: + +memory_controllers { + ranges; + compatible = "simple-bus"; + + memc@0 { + compatible = "brcm,brcmstb-memc", "simple-bus"; + ranges; + + ddr-phy@f1106000 { + compatible = "brcm,brcmstb-ddr-phy-v240.1"; + reg = <0xf1106000 0x21c>; + }; + + shimphy@f1108000 { + compatible = "brcm,brcmstb-ddr-shimphy-v1.0"; + reg = <0xf1108000 0xe4>; + }; + + memc-ddr@f1102000 { + reg = <0xf1102000 0x800>; + compatible = "brcm,brcmstb-memc-ddr"; + }; + }; + + memc@1 { + compatible = "brcm,brcmstb-memc", "simple-bus"; + ranges; + + ddr-phy@f1186000 { + compatible = "brcm,brcmstb-ddr-phy-v240.1"; + reg = <0xf1186000 0x21c>; + }; + + shimphy@f1188000 { + compatible = "brcm,brcmstb-ddr-shimphy-v1.0"; + reg = <0xf1188000 0xe4>; + }; + + memc-ddr@f1182000 { + reg = <0xf1182000 0x800>; + compatible = "brcm,brcmstb-memc-ddr"; + }; + }; + + memc@2 { + compatible = "brcm,brcmstb-memc", "simple-bus"; + ranges; + + ddr-phy@f1206000 { + compatible = "brcm,brcmstb-ddr-phy-v240.1"; + reg = <0xf1206000 0x21c>; + }; + + shimphy@f1208000 { + compatible = "brcm,brcmstb-ddr-shimphy-v1.0"; + reg = <0xf1208000 0xe4>; + }; + + memc-ddr@f1202000 { + reg = <0xf1202000 0x800>; + compatible = "brcm,brcmstb-memc-ddr"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,nsp.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,nsp.txt new file mode 100644 index 000000000000..eae53e4556be --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,nsp.txt @@ -0,0 +1,34 @@ +Broadcom Northstar Plus device tree bindings +-------------------------------------------- + +Broadcom Northstar Plus family of SoCs are used for switching control +and management applications as well as residential router/gateway +applications. The SoC features dual core Cortex A9 ARM CPUs, integrating +several peripheral interfaces including multiple Gigabit Ethernet PHYs, +DDR3 memory, PCIE Gen-2, USB 2.0 and USB 3.0, serial and NAND flash, +SATA and several other IO controllers. + +Boards with Northstar Plus SoCs shall have the following properties: + +Required root node property: + +BCM58522 +compatible = "brcm,bcm58522", "brcm,nsp"; + +BCM58525 +compatible = "brcm,bcm58525", "brcm,nsp"; + +BCM58535 +compatible = "brcm,bcm58535", "brcm,nsp"; + +BCM58622 +compatible = "brcm,bcm58622", "brcm,nsp"; + +BCM58623 +compatible = "brcm,bcm58623", "brcm,nsp"; + +BCM58625 +compatible = "brcm,bcm58625", "brcm,nsp"; + +BCM88312 +compatible = "brcm,bcm88312", "brcm,nsp"; diff --git a/Documentation/devicetree/bindings/arm/coherency-fabric.txt b/Documentation/devicetree/bindings/arm/coherency-fabric.txt index 8dd46617c889..9b5c3f620e65 100644 --- a/Documentation/devicetree/bindings/arm/coherency-fabric.txt +++ b/Documentation/devicetree/bindings/arm/coherency-fabric.txt @@ -27,6 +27,11 @@ Required properties: * For "marvell,armada-380-coherency-fabric", only one pair is needed for the per-CPU fabric registers. +Optional properties: + +- broken-idle: boolean to set when the Idle mode is not supported by the + hardware. + Examples: coherency-fabric@d0020200 { diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index 91e6e5c478d0..3a07a87fef20 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -195,6 +195,8 @@ nodes to be present and contain the properties described below. "marvell,armada-380-smp" "marvell,armada-390-smp" "marvell,armada-xp-smp" + "mediatek,mt6589-smp" + "mediatek,mt81xx-tz-smp" "qcom,gcc-msm8660" "qcom,kpss-acc-v1" "qcom,kpss-acc-v2" diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt index 2a3ba73f0c5c..34c88b0c7ab4 100644 --- a/Documentation/devicetree/bindings/arm/fsl.txt +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -128,10 +128,18 @@ Example: reg = <0x0 0x1ee0000 0x0 0x10000>; }; -Freescale LS2085A SoC Device Tree Bindings ------------------------------------------- +Freescale ARMv8 based Layerscape SoC family Device Tree Bindings +---------------------------------------------------------------- -LS2085A ARMv8 based Simulator model +LS2080A ARMv8 based Simulator model Required root node properties: - - compatible = "fsl,ls2085a-simu", "fsl,ls2085a"; + - compatible = "fsl,ls2080a-simu", "fsl,ls2080a"; + +LS2080A ARMv8 based QDS Board +Required root node properties: + - compatible = "fsl,ls2080a-qds", "fsl,ls2080a"; + +LS2080A ARMv8 based RDB Board +Required root node properties: + - compatible = "fsl,ls2080a-rdb", "fsl,ls2080a"; diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt index 764c738bb3ba..6ac7c000af22 100644 --- a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt +++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt @@ -20,6 +20,10 @@ HiKey Board Required root node properties: - compatible = "hisilicon,hi6220-hikey", "hisilicon,hi6220"; +HiP05 D02 Board +Required root node properties: + - compatible = "hisilicon,hip05-d02"; + Hisilicon system controller Required properties: diff --git a/Documentation/devicetree/bindings/arm/keystone/keystone.txt b/Documentation/devicetree/bindings/arm/keystone/keystone.txt index 59d7a46f85eb..3090a8a008c0 100644 --- a/Documentation/devicetree/bindings/arm/keystone/keystone.txt +++ b/Documentation/devicetree/bindings/arm/keystone/keystone.txt @@ -9,12 +9,26 @@ Required properties: the form "ti,keystone-*". Generic devices like gic, arch_timers, ns16550 type UART should use the specified compatible for those devices. +SoC families: + +- Keystone 2 generic SoC: + compatible = "ti,keystone" + +SoCs: + +- Keystone 2 Hawking/Kepler + compatible = "ti,k2hk", "ti,keystone" +- Keystone 2 Lamarr + compatible = "ti,k2l", "ti,keystone" +- Keystone 2 Edison + compatible = "ti,k2e", "ti,keystone" + Boards: - Keystone 2 Hawking/Kepler EVM - compatible = "ti,k2hk-evm","ti,keystone" + compatible = "ti,k2hk-evm", "ti,k2hk", "ti,keystone" - Keystone 2 Lamarr EVM - compatible = "ti,k2l-evm","ti,keystone" + compatible = "ti,k2l-evm", "ti, k2l", "ti,keystone" - Keystone 2 Edison EVM - compatible = "ti,k2e-evm","ti,keystone" + compatible = "ti,k2e-evm", "ti,k2e", "ti,keystone" diff --git a/Documentation/devicetree/bindings/arm/mvebu-cpu-config.txt b/Documentation/devicetree/bindings/arm/mvebu-cpu-config.txt new file mode 100644 index 000000000000..2cdcd716da40 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mvebu-cpu-config.txt @@ -0,0 +1,20 @@ +MVEBU CPU Config registers +-------------------------- + +MVEBU (Marvell SOCs: Armada 370/XP) + +Required properties: + +- compatible: one of: + - "marvell,armada-370-cpu-config" + - "marvell,armada-xp-cpu-config" + +- reg: Should contain CPU config registers location and length, in + their per-CPU variant + +Example: + + cpu-config@21000 { + compatible = "marvell,armada-xp-cpu-config"; + reg = <0x21000 0x8>; + }; diff --git a/Documentation/devicetree/bindings/arm/pmu.txt b/Documentation/devicetree/bindings/arm/pmu.txt index 4b7c3d9b29bb..97ba45af04fc 100644 --- a/Documentation/devicetree/bindings/arm/pmu.txt +++ b/Documentation/devicetree/bindings/arm/pmu.txt @@ -7,6 +7,7 @@ representation in the device tree should be done as under:- Required properties: - compatible : should be one of + "apm,potenza-pmu" "arm,armv8-pmuv3" "arm.cortex-a57-pmu" "arm.cortex-a53-pmu" diff --git a/Documentation/devicetree/bindings/arm/psci.txt b/Documentation/devicetree/bindings/arm/psci.txt index 5aa40ede0e99..a9adab84e2fe 100644 --- a/Documentation/devicetree/bindings/arm/psci.txt +++ b/Documentation/devicetree/bindings/arm/psci.txt @@ -31,6 +31,10 @@ Main node required properties: support, but are permitted to be present for compatibility with existing software when "arm,psci" is later in the compatible list. + * "arm,psci-1.0" : for implementations complying to PSCI 1.0. PSCI 1.0 is + backward compatible with PSCI 0.2 with minor specification updates, + as defined in the PSCI specification[2]. + - method : The method of calling the PSCI firmware. Permitted values are: @@ -100,3 +104,5 @@ Case 3: PSCI v0.2 and PSCI v0.1. [1] Kernel documentation - ARM idle states bindings Documentation/devicetree/bindings/arm/idle-states.txt +[2] Power State Coordination Interface (PSCI) specification + http://infocenter.arm.com/help/topic/com.arm.doc.den0022c/DEN0022C_Power_State_Coordination_Interface.pdf diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index af58cd74aeff..8e985dd2f181 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -17,6 +17,10 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "radxa,rock", "rockchip,rk3188"; +- Radxa Rock2 Square board: + Required root node properties: + - compatible = "radxa,rock2-square", "rockchip,rk3288"; + - Firefly Firefly-RK3288 board: Required root node properties: - compatible = "firefly,firefly-rk3288", "rockchip,rk3288"; @@ -31,6 +35,13 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "netxeon,r89", "rockchip,rk3288"; +- Google Jaq (Haier Chromebook 11 and more): + Required root node properties: + - compatible = "google,veyron-jaq-rev5", "google,veyron-jaq-rev4", + "google,veyron-jaq-rev3", "google,veyron-jaq-rev2", + "google,veyron-jaq-rev1", "google,veyron-jaq", + "google,veyron", "rockchip,rk3288"; + - Google Jerry (Hisense Chromebook C11 and more): Required root node properties: - compatible = "google,veyron-jerry-rev7", "google,veyron-jerry-rev6", diff --git a/Documentation/devicetree/bindings/arm/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung-boards.txt deleted file mode 100644 index 43589d2466a7..000000000000 --- a/Documentation/devicetree/bindings/arm/samsung-boards.txt +++ /dev/null @@ -1,27 +0,0 @@ -* Samsung's Exynos SoC based boards - -Required root node properties: - - compatible = should be one or more of the following. - - "samsung,monk" - for Exynos3250-based Samsung Simband board. - - "samsung,rinato" - for Exynos3250-based Samsung Gear2 board. - - "samsung,smdkv310" - for Exynos4210-based Samsung SMDKV310 eval board. - - "samsung,trats" - for Exynos4210-based Tizen Reference board. - - "samsung,universal_c210" - for Exynos4210-based Samsung board. - - "samsung,smdk4412", - for Exynos4412-based Samsung SMDK4412 eval board. - - "samsung,trats2" - for Exynos4412-based Tizen Reference board. - - "samsung,smdk5250" - for Exynos5250-based Samsung SMDK5250 eval board. - - "samsung,xyref5260" - for Exynos5260-based Samsung board. - - "samsung,smdk5410" - for Exynos5410-based Samsung SMDK5410 eval board. - - "samsung,smdk5420" - for Exynos5420-based Samsung SMDK5420 eval board. - - "samsung,sd5v1" - for Exynos5440-based Samsung board. - - "samsung,ssdk5440" - for Exynos5440-based Samsung board. - -Optional: - - firmware node, specifying presence and type of secure firmware: - - compatible: only "samsung,secure-firmware" is currently supported - - reg: address of non-secure SYSRAM used for communication with firmware - - firmware@0203F000 { - compatible = "samsung,secure-firmware"; - reg = <0x0203F000 0x1000>; - }; diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt new file mode 100644 index 000000000000..12129c011c8f --- /dev/null +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt @@ -0,0 +1,69 @@ +* Samsung's Exynos SoC based boards + +Required root node properties: + - compatible = should be one or more of the following. + - "samsung,monk" - for Exynos3250-based Samsung Simband board. + - "samsung,rinato" - for Exynos3250-based Samsung Gear2 board. + - "samsung,smdkv310" - for Exynos4210-based Samsung SMDKV310 eval board. + - "samsung,trats" - for Exynos4210-based Tizen Reference board. + - "samsung,universal_c210" - for Exynos4210-based Samsung board. + - "samsung,smdk4412", - for Exynos4412-based Samsung SMDK4412 eval board. + - "samsung,trats2" - for Exynos4412-based Tizen Reference board. + - "samsung,smdk5250" - for Exynos5250-based Samsung SMDK5250 eval board. + - "samsung,xyref5260" - for Exynos5260-based Samsung board. + - "samsung,smdk5410" - for Exynos5410-based Samsung SMDK5410 eval board. + - "samsung,smdk5420" - for Exynos5420-based Samsung SMDK5420 eval board. + - "samsung,sd5v1" - for Exynos5440-based Samsung board. + - "samsung,ssdk5440" - for Exynos5440-based Samsung board. + +* Other companies Exynos SoC based + * FriendlyARM + - "friendlyarm,tiny4412" - for Exynos4412-based FriendlyARM + TINY4412 board. + + * Google + - "google,pi" - for Exynos5800-based Google Peach Pi + Rev 10+ board, + also: "google,pi-rev16", "google,pi-rev15", "google,pi-rev14", + "google,pi-rev13", "google,pi-rev12", "google,pi-rev11", + "google,pi-rev10", "google,peach". + + - "google,pit" - for Exynos5420-based Google Peach Pit + Rev 6+ (Exynos5420), + also: "google,pit-rev16", "google,pit-rev15", "google,pit-rev14", + "google,pit-rev13", "google,pit-rev12", "google,pit-rev11", + "google,pit-rev10", "google,pit-rev9", "google,pit-rev8", + "google,pit-rev7", "google,pit-rev6", "google,peach". + + - "google,snow-rev4" - for Exynos5250-based Google Snow board, + also: "google,snow" + - "google,snow-rev5" - for Exynos5250-based Google Snow + Rev 5+ board. + - "google,spring" - for Exynos5250-based Google Spring board. + + * Hardkernel + - "hardkernel,odroid-u3" - for Exynos4412-based Hardkernel Odroid U3. + - "hardkernel,odroid-x" - for Exynos4412-based Hardkernel Odroid X. + - "hardkernel,odroid-x2" - for Exynos4412-based Hardkernel Odroid X2. + - "hardkernel,odroid-xu3" - for Exynos5422-based Hardkernel Odroid XU3. + - "hardkernel,odroid-xu3-lite" - for Exynos5422-based Hardkernel + Odroid XU3 Lite board. + - "hardkernel,odroid-xu4" - for Exynos5422-based Hardkernel Odroid XU4. + + * Insignal + - "insignal,arndale" - for Exynos5250-based Insignal Arndale board. + - "insignal,arndale-octa" - for Exynos5420-based Insignal Arndale + Octa board. + - "insignal,origen" - for Exynos4210-based Insignal Origen board. + - "insignal,origen4412 - for Exynos4412-based Insignal Origen board. + + +Optional nodes: + - firmware node, specifying presence and type of secure firmware: + - compatible: only "samsung,secure-firmware" is currently supported + - reg: address of non-secure SYSRAM used for communication with firmware + + firmware@0203F000 { + compatible = "samsung,secure-firmware"; + reg = <0x0203F000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt index c4f19b2e7dd9..40bb9007cd0d 100644 --- a/Documentation/devicetree/bindings/arm/shmobile.txt +++ b/Documentation/devicetree/bindings/arm/shmobile.txt @@ -39,8 +39,6 @@ Boards: compatible = "renesas,armadillo800eva" - BOCK-W compatible = "renesas,bockw", "renesas,r8a7778" - - BOCK-W - Reference Device Tree Implementation - compatible = "renesas,bockw-reference", "renesas,r8a7778" - Genmai (RTK772100BC00000BR) compatible = "renesas,genmai", "renesas,r7s72100" - Gose @@ -57,7 +55,7 @@ Boards: compatible = "renesas,lager", "renesas,r8a7790" - Marzen compatible = "renesas,marzen", "renesas,r8a7779" - -Note: Reference Device Tree Implementations are temporary implementations - to ease the migration from platform devices to Device Tree, and are - intended to be removed in the future. + - Porter (M2-LCDP) + compatible = "renesas,porter", "renesas,r8a7791" + - SILK (RTP0RC7794LCB00011S) + compatible = "renesas,silk", "renesas,r8a7794" diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt index 67da20539540..bb9b0faa919d 100644 --- a/Documentation/devicetree/bindings/arm/sunxi.txt +++ b/Documentation/devicetree/bindings/arm/sunxi.txt @@ -6,6 +6,7 @@ using one of the following compatible strings: allwinner,sun4i-a10 allwinner,sun5i-a10s allwinner,sun5i-a13 + allwinner,sun5i-r8 allwinner,sun6i-a31 allwinner,sun7i-a20 allwinner,sun8i-a23 diff --git a/Documentation/devicetree/bindings/arm/uniphier/cache-uniphier.txt b/Documentation/devicetree/bindings/arm/uniphier/cache-uniphier.txt new file mode 100644 index 000000000000..d27a646f48a9 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/uniphier/cache-uniphier.txt @@ -0,0 +1,60 @@ +UniPhier outer cache controller + +UniPhier SoCs are integrated with a full-custom outer cache controller system. +All of them have a level 2 cache controller, and some have a level 3 cache +controller as well. + +Required properties: +- compatible: should be "socionext,uniphier-system-cache" +- reg: offsets and lengths of the register sets for the device. It should + contain 3 regions: control register, revision register, operation register, + in this order. +- cache-unified: specifies the cache is a unified cache. +- cache-size: specifies the size in bytes of the cache +- cache-sets: specifies the number of associativity sets of the cache +- cache-line-size: specifies the line size in bytes +- cache-level: specifies the level in the cache hierarchy. The value should + be 2 for L2 cache, 3 for L3 cache, etc. + +Optional properties: +- next-level-cache: phandle to the next level cache if present. The next level + cache should be also compatible with "socionext,uniphier-system-cache". + +The L2 cache must exist to use the L3 cache; the cache hierarchy must be +indicated correctly with "next-level-cache" properties. + +Example 1 (system with L2): + l2: l2-cache@500c0000 { + compatible = "socionext,uniphier-system-cache"; + reg = <0x500c0000 0x2000>, <0x503c0100 0x4>, + <0x506c0000 0x400>; + cache-unified; + cache-size = <0x80000>; + cache-sets = <256>; + cache-line-size = <128>; + cache-level = <2>; + }; + +Example 2 (system with L2 and L3): + l2: l2-cache@500c0000 { + compatible = "socionext,uniphier-system-cache"; + reg = <0x500c0000 0x2000>, <0x503c0100 0x8>, + <0x506c0000 0x400>; + cache-unified; + cache-size = <0x200000>; + cache-sets = <512>; + cache-line-size = <128>; + cache-level = <2>; + next-level-cache = <&l3>; + }; + + l3: l3-cache@500c8000 { + compatible = "socionext,uniphier-system-cache"; + reg = <0x500c8000 0x2000>, <0x503c8100 0x8>, + <0x506c8000 0x400>; + cache-unified; + cache-size = <0x400000>; + cache-sets = <512>; + cache-line-size = <256>; + cache-level = <3>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/board.txt b/Documentation/devicetree/bindings/board/fsl-board.txt index cff38bdbc0e4..fb7b03ec2071 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/board.txt +++ b/Documentation/devicetree/bindings/board/fsl-board.txt @@ -21,11 +21,14 @@ Example: This is the memory-mapped registers for on board FPGA. -Required properities: +Required properties: - compatible: should be a board-specific string followed by a string indicating the type of FPGA. Example: - "fsl,<board>-fpga", "fsl,fpga-pixis" + "fsl,<board>-fpga", "fsl,fpga-pixis", or + "fsl,<board>-fpga", "fsl,fpga-qixis" - reg: should contain the address and the length of the FPGA register set. + +Optional properties: - interrupt-parent: should specify phandle for the interrupt controller. - interrupts: should specify event (wakeup) IRQ. @@ -38,6 +41,13 @@ Example (P1022DS): interrupts = <8 8 0 0>; }; +Example (LS2080A-RDB): + + cpld@3,0 { + compatible = "fsl,ls2080ardb-fpga", "fsl,fpga-qixis"; + reg = <0x3 0 0x10000>; + }; + * Freescale BCSR GPIO banks Some BCSR registers act as simple GPIO controllers, each such diff --git a/Documentation/devicetree/bindings/bus/sunxi-rsb.txt b/Documentation/devicetree/bindings/bus/sunxi-rsb.txt new file mode 100644 index 000000000000..3dd28343b6ce --- /dev/null +++ b/Documentation/devicetree/bindings/bus/sunxi-rsb.txt @@ -0,0 +1,47 @@ +Allwinner Reduced Serial Bus (RSB) controller + +The RSB controller found on later Allwinner SoCs is an SMBus like 2 wire +serial bus with 1 master and up to 15 slaves. It is represented by a node +for the controller itself, and child nodes representing the slave devices. + +Required properties : + + - reg : Offset and length of the register set for the controller. + - compatible : Shall be "allwinner,sun8i-a23-rsb". + - interrupts : The interrupt line associated to the RSB controller. + - clocks : The gate clk associated to the RSB controller. + - resets : The reset line associated to the RSB controller. + - #address-cells : shall be 1 + - #size-cells : shall be 0 + +Optional properties : + + - clock-frequency : Desired RSB bus clock frequency in Hz. Maximum is 20MHz. + If not set this defaults to 3MHz. + +Child nodes: + +An RSB controller node can contain zero or more child nodes representing +slave devices on the bus. Child 'reg' properties should contain the slave +device's hardware address. The hardware address is hardwired in the device, +which can normally be found in the datasheet. + +Example: + + rsb@01f03400 { + compatible = "allwinner,sun8i-a23-rsb"; + reg = <0x01f03400 0x400>; + interrupts = <0 39 4>; + clocks = <&apb0_gates 3>; + clock-frequency = <3000000>; + resets = <&apb0_rst 3>; + #address-cells = <1>; + #size-cells = <0>; + + pmic@3e3 { + compatible = "..."; + reg = <0x3e3>; + + /* ... */ + }; + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,gcc.txt b/Documentation/devicetree/bindings/clock/qcom,gcc.txt index 54c23f34f194..152dfaab2575 100644 --- a/Documentation/devicetree/bindings/clock/qcom,gcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,gcc.txt @@ -18,10 +18,14 @@ Required properties : - #clock-cells : shall contain 1 - #reset-cells : shall contain 1 +Optional properties : +- #power-domain-cells : shall contain 1 + Example: clock-controller@900000 { compatible = "qcom,gcc-msm8960"; reg = <0x900000 0x4000>; #clock-cells = <1>; #reset-cells = <1>; + #power-domain-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/clock/qcom,mmcc.txt b/Documentation/devicetree/bindings/clock/qcom,mmcc.txt index 29ebf84d25af..34e7614d5074 100644 --- a/Documentation/devicetree/bindings/clock/qcom,mmcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,mmcc.txt @@ -14,10 +14,14 @@ Required properties : - #clock-cells : shall contain 1 - #reset-cells : shall contain 1 +Optional properties : +- #power-domain-cells : shall contain 1 + Example: clock-controller@4000000 { compatible = "qcom,mmcc-msm8960"; reg = <0x4000000 0x1000>; #clock-cells = <1>; #reset-cells = <1>; + #power-domain-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt b/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt new file mode 100644 index 000000000000..56a961aa5061 --- /dev/null +++ b/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt @@ -0,0 +1,65 @@ +Broadcom VC4 (VideoCore4) GPU + +The VC4 device present on the Raspberry Pi includes a display system +with HDMI output and the HVS (Hardware Video Scaler) for compositing +display planes. + +Required properties for VC4: +- compatible: Should be "brcm,bcm2835-vc4" + +Required properties for Pixel Valve: +- compatible: Should be one of "brcm,bcm2835-pixelvalve0", + "brcm,bcm2835-pixelvalve1", or "brcm,bcm2835-pixelvalve2" +- reg: Physical base address and length of the PV's registers +- interrupts: The interrupt number + See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt + +Required properties for HVS: +- compatible: Should be "brcm,bcm2835-hvs" +- reg: Physical base address and length of the HVS's registers +- interrupts: The interrupt number + See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt + +Required properties for HDMI +- compatible: Should be "brcm,bcm2835-hdmi" +- reg: Physical base address and length of the two register ranges + ("HDMI" and "HD", in that order) +- interrupts: The interrupt numbers + See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt +- ddc: phandle of the I2C controller used for DDC EDID probing +- clocks: a) hdmi: The HDMI state machine clock + b) pixel: The pixel clock. + +Optional properties for HDMI: +- hpd-gpios: The GPIO pin for HDMI hotplug detect (if it doesn't appear + as an interrupt/status bit in the HDMI controller + itself). See bindings/pinctrl/brcm,bcm2835-gpio.txt + +Example: +pixelvalve@7e807000 { + compatible = "brcm,bcm2835-pixelvalve2"; + reg = <0x7e807000 0x100>; + interrupts = <2 10>; /* pixelvalve */ +}; + +hvs@7e400000 { + compatible = "brcm,bcm2835-hvs"; + reg = <0x7e400000 0x6000>; + interrupts = <2 1>; +}; + +hdmi: hdmi@7e902000 { + compatible = "brcm,bcm2835-hdmi"; + reg = <0x7e902000 0x600>, + <0x7e808000 0x100>; + interrupts = <2 8>, <2 9>; + ddc = <&i2c2>; + hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>; + clocks = <&clocks BCM2835_PLLH_PIX>, + <&clocks BCM2835_CLOCK_HSM>; + clock-names = "pixel", "hdmi"; +}; + +vc4: gpu { + compatible = "brcm,bcm2835-vc4"; +}; diff --git a/Documentation/devicetree/bindings/display/msm/hdmi.txt b/Documentation/devicetree/bindings/display/msm/hdmi.txt index e926239e1101..379ee2ea9a3d 100644 --- a/Documentation/devicetree/bindings/display/msm/hdmi.txt +++ b/Documentation/devicetree/bindings/display/msm/hdmi.txt @@ -2,6 +2,7 @@ Qualcomm adreno/snapdragon hdmi output Required properties: - compatible: one of the following + * "qcom,hdmi-tx-8996" * "qcom,hdmi-tx-8994" * "qcom,hdmi-tx-8084" * "qcom,hdmi-tx-8974" @@ -21,6 +22,7 @@ Required properties: Optional properties: - qcom,hdmi-tx-mux-en-gpio: hdmi mux enable pin - qcom,hdmi-tx-mux-sel-gpio: hdmi mux select pin +- power-domains: reference to the power domain(s), if available. - pinctrl-names: the pin control state names; should contain "default" - pinctrl-0: the default pinctrl state (active) - pinctrl-1: the "sleep" pinctrl state @@ -35,6 +37,7 @@ Example: reg-names = "core_physical"; reg = <0x04a00000 0x1000>; interrupts = <GIC_SPI 79 0>; + power-domains = <&mmcc MDSS_GDSC>; clock-names = "core_clk", "master_iface_clk", diff --git a/Documentation/devicetree/bindings/display/msm/mdp.txt b/Documentation/devicetree/bindings/display/msm/mdp.txt index 1a0598e5279d..0833edaba4c3 100644 --- a/Documentation/devicetree/bindings/display/msm/mdp.txt +++ b/Documentation/devicetree/bindings/display/msm/mdp.txt @@ -11,13 +11,14 @@ Required properties: - clock-names: the following clocks are required: * "core_clk" * "iface_clk" - * "lut_clk" * "src_clk" * "hdmi_clk" * "mpd_clk" Optional properties: - gpus: phandle for gpu device +- clock-names: the following clocks are optional: + * "lut_clk" Example: diff --git a/Documentation/devicetree/bindings/display/renesas,du.txt b/Documentation/devicetree/bindings/display/renesas,du.txt index c902323928f7..eccd4f4867b2 100644 --- a/Documentation/devicetree/bindings/display/renesas,du.txt +++ b/Documentation/devicetree/bindings/display/renesas,du.txt @@ -5,7 +5,9 @@ Required Properties: - compatible: must be one of the following. - "renesas,du-r8a7779" for R8A7779 (R-Car H1) compatible DU - "renesas,du-r8a7790" for R8A7790 (R-Car H2) compatible DU - - "renesas,du-r8a7791" for R8A7791 (R-Car M2) compatible DU + - "renesas,du-r8a7791" for R8A7791 (R-Car M2-W) compatible DU + - "renesas,du-r8a7793" for R8A7793 (R-Car M2-N) compatible DU + - "renesas,du-r8a7794" for R8A7794 (R-Car E2) compatible DU - reg: A list of base address and length of each memory resource, one for each entry in the reg-names property. @@ -22,9 +24,9 @@ Required Properties: - clock-names: Name of the clocks. This property is model-dependent. - R8A7779 uses a single functional clock. The clock doesn't need to be named. - - R8A7790 and R8A7791 use one functional clock per channel and one clock - per LVDS encoder. The functional clocks must be named "du.x" with "x" - being the channel numerical index. The LVDS clocks must be named + - R8A779[0134] use one functional clock per channel and one clock per LVDS + encoder (if available). The functional clocks must be named "du.x" with + "x" being the channel numerical index. The LVDS clocks must be named "lvds.x" with "x" being the LVDS encoder numerical index. - In addition to the functional and encoder clocks, all DU versions also support externally supplied pixel clocks. Those clocks are optional. @@ -43,7 +45,9 @@ corresponding to each DU output. ----------------------------------------------------------------------------- R8A7779 (H1) DPAD 0 DPAD 1 - R8A7790 (H2) DPAD LVDS 0 LVDS 1 - R8A7791 (M2) DPAD LVDS 0 - + R8A7791 (M2-W) DPAD LVDS 0 - + R8A7793 (M2-N) DPAD LVDS 0 - + R8A7794 (E2) DPAD 0 DPAD 1 - Example: R8A7790 (R-Car H2) DU diff --git a/Documentation/devicetree/bindings/display/ssd1307fb.txt b/Documentation/devicetree/bindings/display/ssd1307fb.txt index d1be78db63f5..eb31ed47a283 100644 --- a/Documentation/devicetree/bindings/display/ssd1307fb.txt +++ b/Documentation/devicetree/bindings/display/ssd1307fb.txt @@ -2,7 +2,8 @@ Required properties: - compatible: Should be "solomon,<chip>fb-<bus>". The only supported bus for - now is i2c, and the supported chips are ssd1305, ssd1306 and ssd1307. + now is i2c, and the supported chips are ssd1305, ssd1306, ssd1307 and + ssd1309. - reg: Should contain address of the controller on the I2C bus. Most likely 0x3c or 0x3d - pwm: Should contain the pwm to use according to the OF device tree PWM diff --git a/Documentation/devicetree/bindings/dma/ti-dma-crossbar.txt b/Documentation/devicetree/bindings/dma/ti-dma-crossbar.txt index 63a48928f3a8..b152a75dceae 100644 --- a/Documentation/devicetree/bindings/dma/ti-dma-crossbar.txt +++ b/Documentation/devicetree/bindings/dma/ti-dma-crossbar.txt @@ -2,9 +2,10 @@ Texas Instruments DMA Crossbar (DMA request router) Required properties: - compatible: "ti,dra7-dma-crossbar" for DRA7xx DMA crossbar + "ti,am335x-edma-crossbar" for AM335x and AM437x - reg: Memory map for accessing module -- #dma-cells: Should be set to <1>. - Clients should use the crossbar request number (input) +- #dma-cells: Should be set to to match with the DMA controller's dma-cells + for ti,dra7-dma-crossbar and <3> for ti,am335x-edma-crossbar. - dma-requests: Number of DMA requests the crossbar can receive - dma-masters: phandle pointing to the DMA controller @@ -14,6 +15,15 @@ The DMA controller node need to have the following poroperties: Optional properties: - ti,dma-safe-map: Safe routing value for unused request lines +Notes: +When requesting channel via ti,dra7-dma-crossbar, the DMA clinet must request +the DMA event number as crossbar ID (input to the DMA crossbar). + +For ti,am335x-edma-crossbar: the meaning of parameters of dmas for clients: +dmas = <&edma_xbar 12 0 1>; where <12> is the DMA request number, <0> is the TC +the event should be assigned and <1> is the mux selection for in the crossbar. +When mux 0 is used the DMA channel can be requested directly from edma node. + Example: /* DMA controller */ @@ -47,6 +57,7 @@ uart1: serial@4806a000 { ti,hwmods = "uart1"; clock-frequency = <48000000>; status = "disabled"; + /* Requesting crossbar input 49 and 50 */ dmas = <&sdma_xbar 49>, <&sdma_xbar 50>; dma-names = "tx", "rx"; }; diff --git a/Documentation/devicetree/bindings/dma/ti-edma.txt b/Documentation/devicetree/bindings/dma/ti-edma.txt index 5ba525a10035..d3d0a4fb1c73 100644 --- a/Documentation/devicetree/bindings/dma/ti-edma.txt +++ b/Documentation/devicetree/bindings/dma/ti-edma.txt @@ -1,4 +1,119 @@ -TI EDMA +Texas Instruments eDMA + +The eDMA3 consists of two components: Channel controller (CC) and Transfer +Controller(s) (TC). The CC is the main entry for DMA users since it is +responsible for the DMA channel handling, while the TCs are responsible to +execute the actual DMA tansfer. + +------------------------------------------------------------------------------ +eDMA3 Channel Controller + +Required properties: +- compatible: "ti,edma3-tpcc" for the channel controller(s) +- #dma-cells: Should be set to <2>. The first number is the DMA request + number and the second is the TC the channel is serviced on. +- reg: Memory map of eDMA CC +- reg-names: "edma3_cc" +- interrupts: Interrupt lines for CCINT, MPERR and CCERRINT. +- interrupt-names: "edma3_ccint", "emda3_mperr" and "edma3_ccerrint" +- ti,tptcs: List of TPTCs associated with the eDMA in the following form: + <&tptc_phandle TC_priority_number>. The highest priority is 0. + +Optional properties: +- ti,hwmods: Name of the hwmods associated to the eDMA CC +- ti,edma-memcpy-channels: List of channels allocated to be used for memcpy, iow + these channels will be SW triggered channels. The list must + contain 16 bits numbers, see example. +- ti,edma-reserved-slot-ranges: PaRAM slot ranges which should not be used by + the driver, they are allocated to be used by for example the + DSP. See example. + +------------------------------------------------------------------------------ +eDMA3 Transfer Controller + +Required properties: +- compatible: "ti,edma3-tptc" for the transfer controller(s) +- reg: Memory map of eDMA TC +- interrupts: Interrupt number for TCerrint. + +Optional properties: +- ti,hwmods: Name of the hwmods associated to the given eDMA TC +- interrupt-names: "edma3_tcerrint" + +------------------------------------------------------------------------------ +Example: + +edma: edma@49000000 { + compatible = "ti,edma3-tpcc"; + ti,hwmods = "tpcc"; + reg = <0x49000000 0x10000>; + reg-names = "edma3_cc"; + interrupts = <12 13 14>; + interrupt-names = "edma3_ccint", "emda3_mperr", "edma3_ccerrint"; + dma-requests = <64>; + #dma-cells = <2>; + + ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 7>, <&edma_tptc2 0>; + + /* Channel 20 and 21 is allocated for memcpy */ + ti,edma-memcpy-channels = /bits/ 16 <20 21>; + /* The following PaRAM slots are reserved: 35-45 and 100-110 */ + ti,edma-reserved-slot-ranges = /bits/ 16 <35 10>, + /bits/ 16 <100 10>; +}; + +edma_tptc0: tptc@49800000 { + compatible = "ti,edma3-tptc"; + ti,hwmods = "tptc0"; + reg = <0x49800000 0x100000>; + interrupts = <112>; + interrupt-names = "edm3_tcerrint"; +}; + +edma_tptc1: tptc@49900000 { + compatible = "ti,edma3-tptc"; + ti,hwmods = "tptc1"; + reg = <0x49900000 0x100000>; + interrupts = <113>; + interrupt-names = "edm3_tcerrint"; +}; + +edma_tptc2: tptc@49a00000 { + compatible = "ti,edma3-tptc"; + ti,hwmods = "tptc2"; + reg = <0x49a00000 0x100000>; + interrupts = <114>; + interrupt-names = "edm3_tcerrint"; +}; + +sham: sham@53100000 { + compatible = "ti,omap4-sham"; + ti,hwmods = "sham"; + reg = <0x53100000 0x200>; + interrupts = <109>; + /* DMA channel 36 executed on eDMA TC0 - low priority queue */ + dmas = <&edma 36 0>; + dma-names = "rx"; +}; + +mcasp0: mcasp@48038000 { + compatible = "ti,am33xx-mcasp-audio"; + ti,hwmods = "mcasp0"; + reg = <0x48038000 0x2000>, + <0x46000000 0x400000>; + reg-names = "mpu", "dat"; + interrupts = <80>, <81>; + interrupt-names = "tx", "rx"; + status = "disabled"; + /* DMA channels 8 and 9 executed on eDMA TC2 - high priority queue */ + dmas = <&edma 8 2>, + <&edma 9 2>; + dma-names = "tx", "rx"; +}; + +------------------------------------------------------------------------------ +DEPRECATED binding, new DTS files must use the ti,edma3-tpcc/ti,edma3-tptc +binding. Required properties: - compatible : "ti,edma3" diff --git a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt index 805ddcd79a57..f2455c50533d 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt @@ -1,9 +1,9 @@ -* Freescale MPC512x/MPC8xxx GPIO controller +* Freescale MPC512x/MPC8xxx/Layerscape GPIO controller Required properties: - compatible : Should be "fsl,<soc>-gpio" The following <soc>s are known to be supported: - mpc5121, mpc5125, mpc8349, mpc8572, mpc8610, pq3, qoriq + mpc5121, mpc5125, mpc8349, mpc8572, mpc8610, pq3, qoriq. - reg : Address and length of the register set for the device - interrupts : Should be the port interrupt shared by all 32 pins. - #gpio-cells : Should be two. The first cell is the pin number and diff --git a/Documentation/devicetree/bindings/hwmon/pwm-fan.txt b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt index 610757ce4492..c6d533202d3e 100644 --- a/Documentation/devicetree/bindings/hwmon/pwm-fan.txt +++ b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt @@ -3,10 +3,35 @@ Bindings for a fan connected to the PWM lines Required properties: - compatible : "pwm-fan" - pwms : the PWM that is used to control the PWM fan +- cooling-levels : PWM duty cycle values in a range from 0 to 255 + which correspond to thermal cooling states Example: - pwm-fan { + fan0: pwm-fan { compatible = "pwm-fan"; - status = "okay"; + cooling-min-state = <0>; + cooling-max-state = <3>; + #cooling-cells = <2>; pwms = <&pwm 0 10000 0>; + cooling-levels = <0 102 170 230>; }; + + thermal-zones { + cpu_thermal: cpu-thermal { + thermal-sensors = <&tmu 0>; + polling-delay-passive = <0>; + polling-delay = <0>; + trips { + cpu_alert1: cpu-alert1 { + temperature = <100000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + }; + cooling-maps { + map0 { + trip = <&cpu_alert1>; + cooling-device = <&fan0 0 1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-davinci.txt b/Documentation/devicetree/bindings/i2c/i2c-davinci.txt index a4e1cbc810c1..5b123e0e4cc2 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-davinci.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-davinci.txt @@ -1,10 +1,10 @@ -* Texas Instruments Davinci I2C +* Texas Instruments Davinci/Keystone I2C This file provides information, what the device node for the -davinci i2c interface contain. +davinci/keystone i2c interface contains. Required properties: -- compatible: "ti,davinci-i2c"; +- compatible: "ti,davinci-i2c" or "ti,keystone-i2c"; - reg : Offset and length of the register set for the device Recommended properties : diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx.txt b/Documentation/devicetree/bindings/i2c/i2c-imx.txt index ce4311d726ae..eab5836ba7f9 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-imx.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-imx.txt @@ -14,6 +14,10 @@ Optional properties: The absence of the propoerty indicates the default frequency 100 kHz. - dmas: A list of two dma specifiers, one for each entry in dma-names. - dma-names: should contain "tx" and "rx". +- scl-gpios: specify the gpio related to SCL pin +- sda-gpios: specify the gpio related to SDA pin +- pinctrl: add extra pinctrl to configure i2c pins to gpio function for i2c + bus recovery, call it "gpio" state Examples: @@ -37,4 +41,9 @@ i2c0: i2c@40066000 { /* i2c0 on vf610 */ dmas = <&edma0 0 50>, <&edma0 0 51>; dma-names = "rx","tx"; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c1>; + pinctrl-1 = <&pinctrl_i2c1_gpio>; + scl-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>; + sda-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt index 16b3e07aa98f..ea406eb20fa5 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt @@ -10,6 +10,7 @@ Required properties: "renesas,i2c-r8a7792" "renesas,i2c-r8a7793" "renesas,i2c-r8a7794" + "renesas,i2c-r8a7795" - reg: physical base address of the controller and length of memory mapped region. - interrupts: interrupt specifier. diff --git a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt index 2bfc6e7ed094..214f94c25d37 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt @@ -10,6 +10,7 @@ Required properties: - "renesas,iic-r8a7792" (R-Car V2H) - "renesas,iic-r8a7793" (R-Car M2-N) - "renesas,iic-r8a7794" (R-Car E2) + - "renesas,iic-r8a7795" (R-Car H3) - "renesas,iic-sh73a0" (SH-Mobile AG5) - reg : address start and address range size of device - interrupts : interrupt of device diff --git a/Documentation/devicetree/bindings/i2c/i2c-uniphier-f.txt b/Documentation/devicetree/bindings/i2c/i2c-uniphier-f.txt new file mode 100644 index 000000000000..27fc6f8c798b --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-uniphier-f.txt @@ -0,0 +1,25 @@ +UniPhier I2C controller (FIFO-builtin) + +Required properties: +- compatible: should be "socionext,uniphier-fi2c". +- #address-cells: should be 1. +- #size-cells: should be 0. +- reg: offset and length of the register set for the device. +- interrupts: a single interrupt specifier. +- clocks: phandle to the input clock. + +Optional properties: +- clock-frequency: desired I2C bus frequency in Hz. The maximum supported + value is 400000. Defaults to 100000 if not specified. + +Examples: + + i2c0: i2c@58780000 { + compatible = "socionext,uniphier-fi2c"; + reg = <0x58780000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 41 4>; + clocks = <&i2c_clk>; + clock-frequency = <100000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-uniphier.txt b/Documentation/devicetree/bindings/i2c/i2c-uniphier.txt new file mode 100644 index 000000000000..26f9d95b3436 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-uniphier.txt @@ -0,0 +1,25 @@ +UniPhier I2C controller (FIFO-less) + +Required properties: +- compatible: should be "socionext,uniphier-i2c". +- #address-cells: should be 1. +- #size-cells: should be 0. +- reg: offset and length of the register set for the device. +- interrupts: a single interrupt specifier. +- clocks: phandle to the input clock. + +Optional properties: +- clock-frequency: desired I2C bus frequency in Hz. The maximum supported + value is 400000. Defaults to 100000 if not specified. + +Examples: + + i2c0: i2c@58400000 { + compatible = "socionext,uniphier-i2c"; + reg = <0x58400000 0x40>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 41 1>; + clocks = <&i2c_clk>; + clock-frequency = <100000>; + }; diff --git a/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt b/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt index 729543c47046..bc620fe32a70 100644 --- a/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt +++ b/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt @@ -47,7 +47,7 @@ Required properties: - clocks: Required if the System MMU is needed to gate its clock. - power-domains: Required if the System MMU is needed to gate its power. Please refer to the following document: - Documentation/devicetree/bindings/arm/exynos/power_domain.txt + Documentation/devicetree/bindings/power/pd-samsung.txt Examples: gsc_0: gsc@13e00000 { diff --git a/Documentation/devicetree/bindings/memory-controllers/arm,pl172.txt b/Documentation/devicetree/bindings/memory-controllers/arm,pl172.txt index e6df32f9986d..22b77ee02f58 100644 --- a/Documentation/devicetree/bindings/memory-controllers/arm,pl172.txt +++ b/Documentation/devicetree/bindings/memory-controllers/arm,pl172.txt @@ -1,8 +1,9 @@ -* Device tree bindings for ARM PL172 MultiPort Memory Controller +* Device tree bindings for ARM PL172/PL175/PL176 MultiPort Memory Controller Required properties: -- compatible: "arm,pl172", "arm,primecell" +- compatible: Must be "arm,primecell" and exactly one from + "arm,pl172", "arm,pl175" or "arm,pl176". - reg: Must contains offset/length value for controller. @@ -56,7 +57,8 @@ Optional child cs node config properties: - mpmc,extended-wait: Enable extended wait. -- mpmc,buffer-enable: Enable write buffer. +- mpmc,buffer-enable: Enable write buffer, option is not supported by + PL175 and PL176 controllers. - mpmc,write-protect: Enable write protect. diff --git a/Documentation/devicetree/bindings/memory-controllers/renesas-memory-controllers.txt b/Documentation/devicetree/bindings/memory-controllers/renesas-memory-controllers.txt index c64b7925cd09..9f78e6c82740 100644 --- a/Documentation/devicetree/bindings/memory-controllers/renesas-memory-controllers.txt +++ b/Documentation/devicetree/bindings/memory-controllers/renesas-memory-controllers.txt @@ -24,9 +24,9 @@ Required properties: Optional properties: - interrupts: Must contain a list of interrupt specifiers for memory controller interrupts, if available. - - interrupts-names: Must contain a list of interrupt names corresponding to - the interrupts in the interrupts property, if available. - Valid interrupt names are: + - interrupt-names: Must contain a list of interrupt names corresponding to + the interrupts in the interrupts property, if available. + Valid interrupt names are: - "sec" (secure interrupt) - "temp" (normal (temperature) interrupt) - power-domains: Must contain a reference to the PM domain that the memory diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt index a42adda944bf..09b94c97faac 100644 --- a/Documentation/devicetree/bindings/mfd/s2mps11.txt +++ b/Documentation/devicetree/bindings/mfd/s2mps11.txt @@ -22,6 +22,10 @@ Optional properties: - samsung,s2mps11-wrstbi-ground: Indicates that WRSTBI pin of PMIC is pulled down. When the system is suspended it will always go down thus triggerring unwanted buck warm reset (setting buck voltages to default values). +- samsung,s2mps11-acokb-ground: Indicates that ACOKB pin of S2MPS11 PMIC is + connected to the ground so the PMIC must manually set PWRHOLD bit in CTRL1 + register to turn off the power. Usually the ACOKB is pulled up to VBATT so + when PWRHOLD pin goes low, the rising ACOKB will trigger power off. Optional nodes: - clocks: s2mps11, s2mps13, s2mps15 and s5m8767 provide three(AP/CP/BT) buffered 32.768 diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index 4efca560adda..9853f8e70966 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -48,6 +48,11 @@ Optional properties: - mac-address : See ethernet.txt file in the same directory - phy-handle : See ethernet.txt file in the same directory +Slave sub-nodes: +- fixed-link : See fixed-link.txt file in the same directory + Either the properties phy_id and phy-mode, + or the sub-node fixed-link can be specified + Note: "ti,hwmods" field is used to fetch the base address and irq resources from TI, omap hwmod data base during device registration. Future plan is to migrate hwmod data base contents into device tree diff --git a/Documentation/devicetree/bindings/pci/arm,juno-r1-pcie.txt b/Documentation/devicetree/bindings/pci/arm,juno-r1-pcie.txt new file mode 100644 index 000000000000..f7514c170a32 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/arm,juno-r1-pcie.txt @@ -0,0 +1,10 @@ +* ARM Juno R1 PCIe interface + +This PCIe host controller is based on PLDA XpressRICH3-AXI IP +and thus inherits all the common properties defined in plda,xpressrich3-axi.txt +as well as the base properties defined in host-generic-pci.txt. + +Required properties: + - compatible: "arm,juno-r1-pcie" + - dma-coherent: The host controller bridges the AXI transactions into PCIe bus + in a manner that makes the DMA operations to appear coherent to the CPUs. diff --git a/Documentation/devicetree/bindings/pci/plda,xpressrich3-axi.txt b/Documentation/devicetree/bindings/pci/plda,xpressrich3-axi.txt new file mode 100644 index 000000000000..f3f75bfb42bc --- /dev/null +++ b/Documentation/devicetree/bindings/pci/plda,xpressrich3-axi.txt @@ -0,0 +1,12 @@ +* PLDA XpressRICH3-AXI host controller + +The PLDA XpressRICH3-AXI host controller can be configured in a manner that +makes it compliant with the SBSA[1] standard published by ARM Ltd. For those +scenarios, the host-generic-pci.txt bindings apply with the following additions +to the compatible property: + +Required properties: + - compatible: should contain "plda,xpressrich3-axi" to identify the IP used. + + +[1] http://infocenter.arm.com/help/topic/com.arm.doc.den0029a/ diff --git a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt b/Documentation/devicetree/bindings/power/pd-samsung.txt index e151057d92f0..4e947372a693 100644 --- a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt +++ b/Documentation/devicetree/bindings/power/pd-samsung.txt @@ -43,9 +43,8 @@ Example: mfc_pd: power-domain@10044060 { compatible = "samsung,exynos4210-pd"; reg = <0x10044060 0x20>; - clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MOUT_SW_ACLK333>, - <&clock CLK_MOUT_USER_ACLK333>; - clock-names = "oscclk", "pclk0", "clk0"; + clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MOUT_USER_ACLK333>; + clock-names = "oscclk", "clk0"; #power-domain-cells = <0>; }; diff --git a/Documentation/devicetree/bindings/pwm/brcm,bcm7038-pwm.txt b/Documentation/devicetree/bindings/pwm/brcm,bcm7038-pwm.txt new file mode 100644 index 000000000000..d9254a6da5ed --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/brcm,bcm7038-pwm.txt @@ -0,0 +1,20 @@ +Broadcom BCM7038 PWM controller (BCM7xxx Set Top Box PWM controller) + +Required properties: + +- compatible: must be "brcm,bcm7038-pwm" +- reg: physical base address and length for this controller +- #pwm-cells: should be 2. See pwm.txt in this directory for a description + of the cells format +- clocks: a phandle to the reference clock for this block which is fed through + its internal variable clock frequency generator + + +Example: + + pwm: pwm@f0408000 { + compatible = "brcm,bcm7038-pwm"; + reg = <0xf0408000 0x28>; + #pwm-cells = <2>; + clocks = <&upg_fixed>; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-berlin.txt b/Documentation/devicetree/bindings/pwm/pwm-berlin.txt new file mode 100644 index 000000000000..82cbe16fcbbc --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-berlin.txt @@ -0,0 +1,17 @@ +Berlin PWM controller + +Required properties: +- compatible: should be "marvell,berlin-pwm" +- reg: physical base address and length of the controller's registers +- clocks: phandle to the input clock +- #pwm-cells: should be 3. See pwm.txt in this directory for a description of + the cells format. + +Example: + +pwm: pwm@f7f20000 { + compatible = "marvell,berlin-pwm"; + reg = <0xf7f20000 0x40>; + clocks = <&chip_clk CLKID_CFG>; + #pwm-cells = <3>; +} diff --git a/Documentation/devicetree/bindings/pwm/pwm-mtk-disp.txt b/Documentation/devicetree/bindings/pwm/pwm-mtk-disp.txt new file mode 100644 index 000000000000..f8f59baf6b67 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-mtk-disp.txt @@ -0,0 +1,42 @@ +MediaTek display PWM controller + +Required properties: + - compatible: should be "mediatek,<name>-disp-pwm": + - "mediatek,mt8173-disp-pwm": found on mt8173 SoC. + - "mediatek,mt6595-disp-pwm": found on mt6595 SoC. + - reg: physical base address and length of the controller's registers. + - #pwm-cells: must be 2. See pwm.txt in this directory for a description of + the cell format. + - clocks: phandle and clock specifier of the PWM reference clock. + - clock-names: must contain the following: + - "main": clock used to generate PWM signals. + - "mm": sync signals from the modules of mmsys. + - pinctrl-names: Must contain a "default" entry. + - pinctrl-0: One property must exist for each entry in pinctrl-names. + See pinctrl/pinctrl-bindings.txt for details of the property values. + +Example: + pwm0: pwm@1401e000 { + compatible = "mediatek,mt8173-disp-pwm", + "mediatek,mt6595-disp-pwm"; + reg = <0 0x1401e000 0 0x1000>; + #pwm-cells = <2>; + clocks = <&mmsys CLK_MM_DISP_PWM026M>, + <&mmsys CLK_MM_DISP_PWM0MM>; + clock-names = "main", "mm"; + pinctrl-names = "default"; + pinctrl-0 = <&disp_pwm0_pins>; + }; + + backlight_lcd: backlight_lcd { + compatible = "pwm-backlight"; + pwms = <&pwm0 0 1000000>; + brightness-levels = < + 0 16 32 48 64 80 96 112 + 128 144 160 176 192 208 224 240 + 255 + >; + default-brightness-level = <9>; + power-supply = <&mt6397_vio18_reg>; + enable-gpios = <&pio 95 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt b/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt index ae0273e19506..cf6068b8e974 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt @@ -3,6 +3,8 @@ Allwinner sun4i and sun7i SoC PWM controller Required properties: - compatible: should be one of: - "allwinner,sun4i-a10-pwm" + - "allwinner,sun5i-a10s-pwm" + - "allwinner,sun5i-a13-pwm" - "allwinner,sun7i-a20-pwm" - reg: physical base address and length of the controller's registers - #pwm-cells: should be 3. See pwm.txt in this directory for a description of diff --git a/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt b/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt new file mode 100644 index 000000000000..0822a083fc57 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt @@ -0,0 +1,26 @@ +* Renesas R-Car PWM Timer Controller + +Required Properties: +- compatible: should be "renesas,pwm-rcar" and one of the following. + - "renesas,pwm-r8a7778": for R-Car M1A + - "renesas,pwm-r8a7779": for R-Car H1 + - "renesas,pwm-r8a7790": for R-Car H2 + - "renesas,pwm-r8a7791": for R-Car M2-W + - "renesas,pwm-r8a7794": for R-Car E2 +- reg: base address and length of the registers block for the PWM. +- #pwm-cells: should be 2. See pwm.txt in this directory for a description of + the cells format. +- clocks: clock phandle and specifier pair. +- pinctrl-0: phandle, referring to a default pin configuration node. +- pinctrl-names: Set to "default". + +Example: R8A7790 (R-Car H2) PWM Timer node + + pwm0: pwm@e6e30000 { + compatible = "renesas,pwm-r8a7790", "renesas,pwm-rcar"; + reg = <0 0xe6e30000 0 0x8>; + #pwm-cells = <2>; + clocks = <&mstp5_clks R8A7790_CLK_PWM>; + pinctrl-0 = <&pwm0_pins>; + pinctrl-names = "default"; + }; diff --git a/Documentation/devicetree/bindings/rtc/dallas,ds1390.txt b/Documentation/devicetree/bindings/rtc/dallas,ds1390.txt new file mode 100644 index 000000000000..8e76f2648796 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/dallas,ds1390.txt @@ -0,0 +1,18 @@ +* Dallas DS1390 SPI Serial Real-Time Clock + +Required properties: +- compatible: Should contain "dallas,ds1390". +- reg: SPI address for chip + +Optional properties: +- trickle-resistor-ohms : Selected resistor for trickle charger + Values usable for ds1390 are 250, 2000, 4000 + Should be given if trickle charger should be enabled +- trickle-diode-disable : Do not use internal trickle charger diode + Should be given if internal trickle charger diode should be disabled +Example: + ds1390: rtc@68 { + compatible = "dallas,ds1390"; + trickle-resistor-ohms = <250>; + reg = <0>; + }; diff --git a/Documentation/devicetree/bindings/rtc/pcf8563.txt b/Documentation/devicetree/bindings/rtc/pcf8563.txt new file mode 100644 index 000000000000..72f6d2c9665e --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/pcf8563.txt @@ -0,0 +1,25 @@ +* Philips PCF8563/Epson RTC8564 Real Time Clock + +Philips PCF8563/Epson RTC8564 Real Time Clock + +Required properties: +see: Documentation/devicetree/bindings/i2c/trivial-devices.txt + +Optional property: +- #clock-cells: Should be 0. +- clock-output-names: + overwrite the default clock name "pcf8563-clkout" + +Example: + +pcf8563: pcf8563@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + #clock-cells = <0>; +}; + +device { +... + clocks = <&pcf8563>; +... +}; diff --git a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt index c0511142b39c..a6c8afc8385a 100644 --- a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt +++ b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt @@ -17,9 +17,9 @@ Required properties: - reg: Address range of the SCPSYS unit - infracfg: must contain a phandle to the infracfg controller - clock, clock-names: clocks according to the common clock binding. - The clocks needed "mm" and "mfg". These are the - clocks which hardware needs to be enabled before - enabling certain power domains. + The clocks needed "mm", "mfg", "venc" and "venc_lt". + These are the clocks which hardware needs to be enabled + before enabling certain power domains. Example: @@ -30,7 +30,9 @@ Example: infracfg = <&infracfg>; clocks = <&clk26m>, <&topckgen CLK_TOP_MM_SEL>; - clock-names = "mfg", "mm"; + <&topckgen CLK_TOP_VENC_SEL>, + <&topckgen CLK_TOP_VENC_LT_SEL>; + clock-names = "mfg", "mm", "venc", "venc_lt"; }; Example consumer: diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smem.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smem.txt new file mode 100644 index 000000000000..9326cdf6e1b1 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smem.txt @@ -0,0 +1,57 @@ +Qualcomm Shared Memory Manager binding + +This binding describes the Qualcomm Shared Memory Manager, used to share data +between various subsystems and OSes in Qualcomm platforms. + +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be: + "qcom,smem" + +- memory-region: + Usage: required + Value type: <prop-encoded-array> + Definition: handle to memory reservation for main SMEM memory region. + +- qcom,rpm-msg-ram: + Usage: required + Value type: <prop-encoded-array> + Definition: handle to RPM message memory resource + +- hwlocks: + Usage: required + Value type: <prop-encoded-array> + Definition: reference to a hwspinlock used to protect allocations from + the shared memory + += EXAMPLE +The following example shows the SMEM setup for MSM8974, with a main SMEM region +at 0xfa00000 and the RPM message ram at 0xfc428000: + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + smem_region: smem@fa00000 { + reg = <0xfa00000 0x200000>; + no-map; + }; + }; + + smem@fa00000 { + compatible = "qcom,smem"; + + memory-region = <&smem_region>; + qcom,rpm-msg-ram = <&rpm_msg_ram>; + + hwlocks = <&tcsr_mutex 3>; + }; + + soc { + rpm_msg_ram: memory@fc428000 { + compatible = "qcom,rpm-msg-ram"; + reg = <0xfc428000 0x4000>; + }; + }; diff --git a/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt b/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt new file mode 100644 index 000000000000..112756e11802 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt @@ -0,0 +1,46 @@ +* Rockchip Power Domains + +Rockchip processors include support for multiple power domains which can be +powered up/down by software based on different application scenes to save power. + +Required properties for power domain controller: +- compatible: Should be one of the following. + "rockchip,rk3288-power-controller" - for RK3288 SoCs. +- #power-domain-cells: Number of cells in a power-domain specifier. + Should be 1 for multiple PM domains. +- #address-cells: Should be 1. +- #size-cells: Should be 0. + +Required properties for power domain sub nodes: +- reg: index of the power domain, should use macros in: + "include/dt-bindings/power/rk3288-power.h" - for RK3288 type power domain. +- clocks (optional): phandles to clocks which need to be enabled while power domain + switches state. + +Example: + + power: power-controller { + compatible = "rockchip,rk3288-power-controller"; + #power-domain-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + + pd_gpu { + reg = <RK3288_PD_GPU>; + clocks = <&cru ACLK_GPU>; + }; + }; + +Node of a device using power domains must have a power-domains property, +containing a phandle to the power device node and an index specifying which +power domain to use. +The index should use macros in: + "include/dt-bindings/power/rk3288-power.h" - for rk3288 type power domain. + +Example of the node using power domain: + + node { + /* ... */ + power-domains = <&power RK3288_PD_GPU>; + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt b/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt index d8e8cdb733f9..d1ce21a4904d 100644 --- a/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt +++ b/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt @@ -221,7 +221,6 @@ qmss: qmss@2a40000 { #size-cells = <1>; ranges; pdsp0@0x2a10000 { - firmware = "keystone/qmss_pdsp_acc48_k2_le_1_0_0_8.fw"; reg = <0x2a10000 0x1000>, <0x2a0f000 0x100>, <0x2a0c000 0x3c8>, diff --git a/Documentation/devicetree/bindings/sound/ak4554.c b/Documentation/devicetree/bindings/sound/ak4554.txt index 934fa02754b3..934fa02754b3 100644 --- a/Documentation/devicetree/bindings/sound/ak4554.c +++ b/Documentation/devicetree/bindings/sound/ak4554.txt diff --git a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt index ef802de4957a..b38200d2583a 100644 --- a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt @@ -12,6 +12,11 @@ Required properties: - resets : Must contain an entry for each entry in reset-names. See ../reset/reset.txt for details. - reset-names : Must include the name "tsadc-apb". +- pinctrl-names : The pin control state names; +- pinctrl-0 : The "init" pinctrl state, it will be set before device probe. +- pinctrl-1 : The "default" pinctrl state, it will be set after reset the + TSADC controller. +- pinctrl-2 : The "sleep" pinctrl state, it will be in for suspend. - #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description. - rockchip,hw-tshut-temp : The hardware-controlled shutdown temperature value. - rockchip,hw-tshut-mode : The hardware-controlled shutdown mode 0:CRU 1:GPIO. @@ -27,8 +32,10 @@ tsadc: tsadc@ff280000 { clock-names = "tsadc", "apb_pclk"; resets = <&cru SRST_TSADC>; reset-names = "tsadc-apb"; - pinctrl-names = "default"; - pinctrl-0 = <&otp_out>; + pinctrl-names = "init", "default", "sleep"; + pinctrl-0 = <&otp_gpio>; + pinctrl-1 = <&otp_out>; + pinctrl-2 = <&otp_gpio>; #thermal-sensor-cells = <1>; rockchip,hw-tshut-temp = <95000>; rockchip,hw-tshut-mode = <0>; diff --git a/Documentation/devicetree/bindings/thermal/ti_soc_thermal.txt b/Documentation/devicetree/bindings/thermal/ti_soc_thermal.txt index 0c9222d27fae..6299dd8de339 100644 --- a/Documentation/devicetree/bindings/thermal/ti_soc_thermal.txt +++ b/Documentation/devicetree/bindings/thermal/ti_soc_thermal.txt @@ -10,6 +10,8 @@ to the silicon temperature. Required properties: - compatible : Should be: + - "ti,omap34xx-bandgap" : for OMAP34xx bandgap + - "ti,omap36xx-bandgap" : for OMAP36xx bandgap - "ti,omap4430-bandgap" : for OMAP4430 bandgap - "ti,omap4460-bandgap" : for OMAP4460 bandgap - "ti,omap4470-bandgap" : for OMAP4470 bandgap @@ -25,6 +27,18 @@ to each bandgap version, because the mapping may change from soc to soc, apart of depending on available features. Example: +OMAP34xx: +bandgap { + reg = <0x48002524 0x4>; + compatible = "ti,omap34xx-bandgap"; +}; + +OMAP36xx: +bandgap { + reg = <0x48002524 0x4>; + compatible = "ti,omap36xx-bandgap"; +}; + OMAP4430: bandgap { reg = <0x4a002260 0x4 0x4a00232C 0x4>; diff --git a/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt b/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt index 53a3029b7589..64083bc5633c 100644 --- a/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt +++ b/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt @@ -3,10 +3,12 @@ Mediatek MT6577, MT6572 and MT6589 Timers Required properties: - compatible should contain: - * "mediatek,mt6589-timer" for MT6589 compatible timers * "mediatek,mt6580-timer" for MT6580 compatible timers - * "mediatek,mt6577-timer" for all compatible timers (MT6589, MT6580, - MT6577) + * "mediatek,mt6589-timer" for MT6589 compatible timers + * "mediatek,mt8127-timer" for MT8127 compatible timers + * "mediatek,mt8135-timer" for MT8135 compatible timers + * "mediatek,mt8173-timer" for MT8173 compatible timers + * "mediatek,mt6577-timer" for MT6577 and all above compatible timers - reg: Should contain location and length for timers register. - clocks: Clocks driving the timer hardware. This list should include two clocks. The order is system clock and as second clock the RTC clock. diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 9ff48e0defb4..fb2ad0acedbd 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -1,6 +1,7 @@ synopsys DWC3 CORE -DWC3- USB3 CONTROLLER +DWC3- USB3 CONTROLLER. Complies to the generic USB binding properties + as described in 'usb/generic.txt' Required properties: - compatible: must be "snps,dwc3" diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 8c6cef73e0d7..55df1d444e9f 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -34,6 +34,7 @@ avago Avago Technologies avic Shanghai AVIC Optoelectronics Co., Ltd. axis Axis Communications AB bosch Bosch Sensortec GmbH +boundary Boundary Devices Inc. brcm Broadcom Corporation buffalo Buffalo, Inc. calxeda Calxeda @@ -171,6 +172,7 @@ pericom Pericom Technology Inc. phytec PHYTEC Messtechnik GmbH picochip Picochip Ltd plathome Plat'Home Co., Ltd. +plda PLDA pixcir PIXCIR MICROELECTRONICS Co., Ltd pulsedlight PulsedLight, Inc powervr PowerVR (deprecated, use img) @@ -228,6 +230,7 @@ toradex Toradex AG toshiba Toshiba Corporation toumaz Toumaz tplink TP-LINK Technologies Co., Ltd. +tronfy Tronfy truly Truly Semiconductors Limited upisemi uPI Semiconductor Corp. usi Universal Scientific Industrial Co., Ltd. diff --git a/Documentation/devicetree/bindings/watchdog/brcm,bcm7038-wdt.txt b/Documentation/devicetree/bindings/watchdog/brcm,bcm7038-wdt.txt new file mode 100644 index 000000000000..84122270be8f --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/brcm,bcm7038-wdt.txt @@ -0,0 +1,19 @@ +BCM7038 Watchdog timer + +Required properties: + +- compatible : should be "brcm,bcm7038-wdt" +- reg : Specifies base physical address and size of the registers. + +Optional properties: + +- clocks: The clock running the watchdog. If no clock is found the + driver will default to 27000000 Hz. + +Example: + +watchdog@f040a7e8 { + compatible = "brcm,bcm7038-wdt"; + clocks = <&upg_fixed>; + reg = <0xf040a7e8 0x16>; +}; |