diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
61 files changed, 1395 insertions, 64 deletions
diff --git a/Documentation/devicetree/bindings/arm/arch_timer.txt b/Documentation/devicetree/bindings/arm/arch_timer.txt index ad440a2b8051..e926aea1147d 100644 --- a/Documentation/devicetree/bindings/arm/arch_timer.txt +++ b/Documentation/devicetree/bindings/arm/arch_timer.txt @@ -31,6 +31,12 @@ to deliver its interrupts via SPIs. This also affects writes to the tval register, due to the implicit counter read. +- hisilicon,erratum-161010101 : A boolean property. Indicates the + presence of Hisilicon erratum 161010101, which says that reading the + counters is unreliable in some cases, and reads may return a value 32 + beyond the correct value. This also affects writes to the tval + registers, due to the implicit counter read. + ** Optional properties: - arm,cpu-registers-not-fw-configured : Firmware does not initialize diff --git a/Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt b/Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt new file mode 100644 index 000000000000..ba0e15ad5bd9 --- /dev/null +++ b/Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt @@ -0,0 +1,128 @@ +TI CPUFreq and OPP bindings +================================ + +Certain TI SoCs, like those in the am335x, am437x, am57xx, and dra7xx +families support different OPPs depending on the silicon variant in use. +The ti-cpufreq driver can use revision and an efuse value from the SoC to +provide the OPP framework with supported hardware information. This is +used to determine which OPPs from the operating-points-v2 table get enabled +when it is parsed by the OPP framework. + +Required properties: +-------------------- +In 'cpus' nodes: +- operating-points-v2: Phandle to the operating-points-v2 table to use. + +In 'operating-points-v2' table: +- compatible: Should be + - 'operating-points-v2-ti-cpu' for am335x, am43xx, and dra7xx/am57xx SoCs +- syscon: A phandle pointing to a syscon node representing the control module + register space of the SoC. + +Optional properties: +-------------------- +For each opp entry in 'operating-points-v2' table: +- opp-supported-hw: Two bitfields indicating: + 1. Which revision of the SoC the OPP is supported by + 2. Which eFuse bits indicate this OPP is available + + A bitwise AND is performed against these values and if any bit + matches, the OPP gets enabled. + +Example: +-------- + +/* From arch/arm/boot/dts/am33xx.dtsi */ +cpus { + #address-cells = <1>; + #size-cells = <0>; + cpu@0 { + compatible = "arm,cortex-a8"; + device_type = "cpu"; + reg = <0>; + + operating-points-v2 = <&cpu0_opp_table>; + + clocks = <&dpll_mpu_ck>; + clock-names = "cpu"; + + clock-latency = <300000>; /* From omap-cpufreq driver */ + }; +}; + +/* + * cpu0 has different OPPs depending on SoC revision and some on revisions + * 0x2 and 0x4 have eFuse bits that indicate if they are available or not + */ +cpu0_opp_table: opp-table { + compatible = "operating-points-v2-ti-cpu"; + syscon = <&scm_conf>; + + /* + * The three following nodes are marked with opp-suspend + * because they can not be enabled simultaneously on a + * single SoC. + */ + opp50@300000000 { + opp-hz = /bits/ 64 <300000000>; + opp-microvolt = <950000 931000 969000>; + opp-supported-hw = <0x06 0x0010>; + opp-suspend; + }; + + opp100@275000000 { + opp-hz = /bits/ 64 <275000000>; + opp-microvolt = <1100000 1078000 1122000>; + opp-supported-hw = <0x01 0x00FF>; + opp-suspend; + }; + + opp100@300000000 { + opp-hz = /bits/ 64 <300000000>; + opp-microvolt = <1100000 1078000 1122000>; + opp-supported-hw = <0x06 0x0020>; + opp-suspend; + }; + + opp100@500000000 { + opp-hz = /bits/ 64 <500000000>; + opp-microvolt = <1100000 1078000 1122000>; + opp-supported-hw = <0x01 0xFFFF>; + }; + + opp100@600000000 { + opp-hz = /bits/ 64 <600000000>; + opp-microvolt = <1100000 1078000 1122000>; + opp-supported-hw = <0x06 0x0040>; + }; + + opp120@600000000 { + opp-hz = /bits/ 64 <600000000>; + opp-microvolt = <1200000 1176000 1224000>; + opp-supported-hw = <0x01 0xFFFF>; + }; + + opp120@720000000 { + opp-hz = /bits/ 64 <720000000>; + opp-microvolt = <1200000 1176000 1224000>; + opp-supported-hw = <0x06 0x0080>; + }; + + oppturbo@720000000 { + opp-hz = /bits/ 64 <720000000>; + opp-microvolt = <1260000 1234800 1285200>; + opp-supported-hw = <0x01 0xFFFF>; + }; + + oppturbo@800000000 { + opp-hz = /bits/ 64 <800000000>; + opp-microvolt = <1260000 1234800 1285200>; + opp-supported-hw = <0x06 0x0100>; + }; + + oppnitro@1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt = <1325000 1298500 1351500>; + opp-supported-hw = <0x04 0x0200>; + }; +}; diff --git a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt index d3ec8e676b6b..d085ef90d27c 100644 --- a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt +++ b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt @@ -123,6 +123,20 @@ Detailed correlation between sub-blocks and power line according to Exynos SoC: |--- FSYS |--- FSYS2 +- In case of Exynos5433, there is VDD_INT power line as following: + VDD_INT |--- G2D (parent device) + |--- MSCL + |--- GSCL + |--- JPEG + |--- MFC + |--- HEVC + |--- BUS0 + |--- BUS1 + |--- BUS2 + |--- PERIS (Fixed clock rate) + |--- PERIC (Fixed clock rate) + |--- FSYS (Fixed clock rate) + Example1: Show the AXI buses of Exynos3250 SoC. Exynos3250 divides the buses to power line (regulator). The MIF (Memory Interface) AXI bus is used to diff --git a/Documentation/devicetree/bindings/dma/stm32-dma.txt b/Documentation/devicetree/bindings/dma/stm32-dma.txt index 70cd13f1588a..4408af693d0c 100644 --- a/Documentation/devicetree/bindings/dma/stm32-dma.txt +++ b/Documentation/devicetree/bindings/dma/stm32-dma.txt @@ -40,8 +40,7 @@ Example: DMA clients connected to the STM32 DMA controller must use the format described in the dma.txt file, using a five-cell specifier for each -channel: a phandle plus four integer cells. -The four cells in order are: +channel: a phandle to the DMA controller plus the following four integer cells: 1. The channel id 2. The request line number @@ -61,7 +60,7 @@ The four cells in order are: 0x1: medium 0x2: high 0x3: very high -5. A 32bit mask specifying the DMA FIFO threshold configuration which are device +4. A 32bit mask specifying the DMA FIFO threshold configuration which are device dependent: -bit 0-1: Fifo threshold 0x0: 1/4 full FIFO diff --git a/Documentation/devicetree/bindings/hwmon/adc128d818.txt b/Documentation/devicetree/bindings/hwmon/adc128d818.txt new file mode 100644 index 000000000000..08bab0e94d25 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/adc128d818.txt @@ -0,0 +1,38 @@ +TI ADC128D818 ADC System Monitor With Temperature Sensor +-------------------------------------------------------- + +Operation modes: + + - Mode 0: 7 single-ended voltage readings (IN0-IN6), + 1 temperature reading (internal) + - Mode 1: 8 single-ended voltage readings (IN0-IN7), + no temperature + - Mode 2: 4 pseudo-differential voltage readings + (IN0-IN1, IN3-IN2, IN4-IN5, IN7-IN6), + 1 temperature reading (internal) + - Mode 3: 4 single-ended voltage readings (IN0-IN3), + 2 pseudo-differential voltage readings + (IN4-IN5, IN7-IN6), + 1 temperature reading (internal) + +If no operation mode is configured via device tree, the driver keeps the +currently active chip operation mode (default is mode 0). + + +Required node properties: + + - compatible: must be set to "ti,adc128d818" + - reg: I2C address of the device + +Optional node properties: + + - ti,mode: Operation mode (see above). + + +Example (operation mode 2): + + adc128d818@1d { + compatible = "ti,adc128d818"; + reg = <0x1d>; + ti,mode = <2>; + }; diff --git a/Documentation/devicetree/bindings/hwmon/lm70.txt b/Documentation/devicetree/bindings/hwmon/lm70.txt index e7fd921aa4f1..ea417a0d32af 100644 --- a/Documentation/devicetree/bindings/hwmon/lm70.txt +++ b/Documentation/devicetree/bindings/hwmon/lm70.txt @@ -4,6 +4,7 @@ Required properties: - compatible: one of "ti,lm70" "ti,tmp121" + "ti,tmp122" "ti,lm71" "ti,lm74" diff --git a/Documentation/devicetree/bindings/hwmon/lm90.txt b/Documentation/devicetree/bindings/hwmon/lm90.txt index e8632486b9ef..97581266e329 100644 --- a/Documentation/devicetree/bindings/hwmon/lm90.txt +++ b/Documentation/devicetree/bindings/hwmon/lm90.txt @@ -33,6 +33,11 @@ Optional properties: LM90 "-ALERT" pin output. See interrupt-controller/interrupts.txt for the format. +- #thermal-sensor-cells: should be set to 1. See thermal/thermal.txt for + details. See <include/dt-bindings/thermal/lm90.h> for the + definition of the local, remote and 2nd remote sensor index + constants. + Example LM90 node: temp-sensor { @@ -41,4 +46,5 @@ temp-sensor { vcc-supply = <&palmas_ldo6_reg>; interrupt-parent = <&gpio>; interrupts = <TEGRA_GPIO(O, 4) IRQ_TYPE_LEVEL_LOW>; + #thermal-sensor-cells = <1>; } diff --git a/Documentation/devicetree/bindings/hwmon/sht15.txt b/Documentation/devicetree/bindings/hwmon/sht15.txt new file mode 100644 index 000000000000..6a80277cc426 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/sht15.txt @@ -0,0 +1,19 @@ +Sensirion SHT15 Humidity and Temperature Sensor + +Required properties: + + - "compatible": must be "sensirion,sht15". + - "data-gpios": GPIO connected to the data line. + - "clk-gpios": GPIO connected to the clock line. + - "vcc-supply": regulator that drives the VCC pin. + +Example: + + sensor { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sensor>; + compatible = "sensirion,sht15"; + clk-gpios = <&gpio4 12 0>; + data-gpios = <&gpio4 13 0>; + vcc-supply = <®_sht15>; + }; diff --git a/Documentation/devicetree/bindings/hwmon/stts751.txt b/Documentation/devicetree/bindings/hwmon/stts751.txt new file mode 100644 index 000000000000..3ee1dc30e72f --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/stts751.txt @@ -0,0 +1,15 @@ +* STTS751 thermometer. + +Required node properties: +- compatible: "stts751" +- reg: I2C bus address of the device + +Optional properties: +- smbus-timeout-disable: when set, the smbus timeout function will be disabled + +Example stts751 node: + +temp-sensor { + compatible = "stts751"; + reg = <0x48>; +} diff --git a/Documentation/devicetree/bindings/interrupt-controller/cortina,gemini-interrupt-controller.txt b/Documentation/devicetree/bindings/interrupt-controller/cortina,gemini-interrupt-controller.txt new file mode 100644 index 000000000000..97c1167fa533 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/cortina,gemini-interrupt-controller.txt @@ -0,0 +1,22 @@ +* Cortina Systems Gemini interrupt controller + +This interrupt controller is found on the Gemini SoCs. + +Required properties: +- compatible: must be "cortina,gemini-interrupt-controller" +- reg: The register bank for the interrupt controller. +- interrupt-controller: Identifies the node as an interrupt controller +- #interrupt-cells: The number of cells to define the interrupts. + Must be 2 as the controller can specify level or rising edge + IRQs. The bindings follows the standard binding for controllers + with two cells specified in + interrupt-controller/interrupts.txt + +Example: + +interrupt-controller@48000000 { + compatible = "cortina,gemini-interrupt-controller"; + reg = <0x48000000 0x1000>; + interrupt-controller; + #interrupt-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/leds/common.txt b/Documentation/devicetree/bindings/leds/common.txt index 696be5792625..24b656014089 100644 --- a/Documentation/devicetree/bindings/leds/common.txt +++ b/Documentation/devicetree/bindings/leds/common.txt @@ -61,16 +61,24 @@ property can be omitted. Examples: -system-status { - label = "Status"; - linux,default-trigger = "heartbeat"; - ... +gpio-leds { + compatible = "gpio-leds"; + + system-status { + label = "Status"; + linux,default-trigger = "heartbeat"; + gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; + }; }; -camera-flash { - label = "Flash"; - led-sources = <0>, <1>; - led-max-microamp = <50000>; - flash-max-microamp = <320000>; - flash-max-timeout-us = <500000>; +max77693-led { + compatible = "maxim,max77693-led"; + + camera-flash { + label = "Flash"; + led-sources = <0>, <1>; + led-max-microamp = <50000>; + flash-max-microamp = <320000>; + flash-max-timeout-us = <500000>; + }; }; diff --git a/Documentation/devicetree/bindings/leds/irled/spi-ir-led.txt b/Documentation/devicetree/bindings/leds/irled/spi-ir-led.txt new file mode 100644 index 000000000000..896b6997cf30 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/irled/spi-ir-led.txt @@ -0,0 +1,29 @@ +Device tree bindings for IR LED connected through SPI bus which is used as +remote controller. + +The IR LED switch is connected to the MOSI line of the SPI device and the data +are delivered thourgh that. + +Required properties: + - compatible: should be "ir-spi-led". + +Optional properties: + - duty-cycle: 8 bit balue that represents the percentage of one period + in which the signal is active. It can be 50, 60, 70, 75, 80 or 90. + - led-active-low: boolean value that specifies whether the output is + negated with a NOT gate. + - power-supply: specifies the power source. It can either be a regulator + or a gpio which enables a regulator, i.e. a regulator-fixed as + described in + Documentation/devicetree/bindings/regulator/fixed-regulator.txt + +Example: + + irled@0 { + compatible = "ir-spi-led"; + reg = <0x0>; + spi-max-frequency = <5000000>; + power-supply = <&vdd_led>; + led-active-low; + duty-cycle = /bits/ 8 <60>; + }; diff --git a/Documentation/devicetree/bindings/media/fsl-vdoa.txt b/Documentation/devicetree/bindings/media/fsl-vdoa.txt new file mode 100644 index 000000000000..6c5628530bb7 --- /dev/null +++ b/Documentation/devicetree/bindings/media/fsl-vdoa.txt @@ -0,0 +1,21 @@ +Freescale Video Data Order Adapter +================================== + +The Video Data Order Adapter (VDOA) is present on the i.MX6q. Its sole purpose +is to reorder video data from the macroblock tiled order produced by the CODA +960 VPU to the conventional raster-scan order for scanout. + +Required properties: +- compatible: must be "fsl,imx6q-vdoa" +- reg: the register base and size for the device registers +- interrupts: the VDOA interrupt +- clocks: the vdoa clock + +Example: + +vdoa@21e4000 { + compatible = "fsl,imx6q-vdoa"; + reg = <0x021e4000 0x4000>; + interrupts = <0 18 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6QDL_CLK_VDOA>; +}; diff --git a/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt b/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt index 56e726ef4bf2..58261fb7b408 100644 --- a/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt +++ b/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt @@ -5,7 +5,8 @@ Required properties: - gpios: specifies GPIO used for IR signal reception. Optional properties: - - linux,rc-map-name: Linux specific remote control map name. + - linux,rc-map-name: see rc.txt file in the same + directory. Example node: diff --git a/Documentation/devicetree/bindings/media/hix5hd2-ir.txt b/Documentation/devicetree/bindings/media/hix5hd2-ir.txt index 54e1bede6244..13ebc0fac9ea 100644 --- a/Documentation/devicetree/bindings/media/hix5hd2-ir.txt +++ b/Documentation/devicetree/bindings/media/hix5hd2-ir.txt @@ -10,7 +10,7 @@ Required properties: - clocks: clock phandle and specifier pair. Optional properties: - - linux,rc-map-name : Remote control map name. + - linux,rc-map-name: see rc.txt file in the same directory. - hisilicon,power-syscon: DEPRECATED. Don't use this in new dts files. Provide correct clocks instead. diff --git a/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt new file mode 100644 index 000000000000..0b7b6a4d84ff --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt @@ -0,0 +1,48 @@ +Toshiba et8ek8 5MP sensor + +Toshiba et8ek8 5MP sensor is an image sensor found in Nokia N900 device + +More detailed documentation can be found in +Documentation/devicetree/bindings/media/video-interfaces.txt . + + +Mandatory properties +-------------------- + +- compatible: "toshiba,et8ek8" +- reg: I2C address (0x3e, or an alternative address) +- vana-supply: Analogue voltage supply (VANA), 2.8 volts +- clocks: External clock to the sensor +- clock-frequency: Frequency of the external clock to the sensor. Camera + driver will set this frequency on the external clock. The clock frequency is + a pre-determined frequency known to be suitable to the board. +- reset-gpios: XSHUTDOWN GPIO. The XSHUTDOWN signal is active low. The sensor + is in hardware standby mode when the signal is in the low state. + + +Endpoint node mandatory properties +---------------------------------- + +- remote-endpoint: A phandle to the bus receiver's endpoint node. + + +Example +------- + +&i2c3 { + clock-frequency = <400000>; + + cam1: camera@3e { + compatible = "toshiba,et8ek8"; + reg = <0x3e>; + vana-supply = <&vaux4>; + clocks = <&isp 0>; + clock-frequency = <9600000>; + reset-gpio = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102 */ + port { + csi_cam1: endpoint { + remote-endpoint = <&csi_out1>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/meson-ir.txt b/Documentation/devicetree/bindings/media/meson-ir.txt index e7e3f3c4fc8f..efd9d29a8f10 100644 --- a/Documentation/devicetree/bindings/media/meson-ir.txt +++ b/Documentation/devicetree/bindings/media/meson-ir.txt @@ -8,6 +8,9 @@ Required properties: - reg : physical base address and length of the device registers - interrupts : a single specifier for the interrupt from the device +Optional properties: + - linux,rc-map-name: see rc.txt file in the same directory. + Example: ir-receiver@c8100480 { diff --git a/Documentation/devicetree/bindings/media/mtk-cir.txt b/Documentation/devicetree/bindings/media/mtk-cir.txt new file mode 100644 index 000000000000..2be2005577d6 --- /dev/null +++ b/Documentation/devicetree/bindings/media/mtk-cir.txt @@ -0,0 +1,24 @@ +Device-Tree bindings for Mediatek consumer IR controller +found in Mediatek SoC family + +Required properties: +- compatible : "mediatek,mt7623-cir" +- clocks : list of clock specifiers, corresponding to + entries in clock-names property; +- clock-names : should contain "clk" entries; +- interrupts : should contain IR IRQ number; +- reg : should contain IO map address for IR. + +Optional properties: +- linux,rc-map-name : see rc.txt file in the same directory. + +Example: + +cir: cir@10013000 { + compatible = "mediatek,mt7623-cir"; + reg = <0 0x10013000 0 0x1000>; + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_INFRA_IRRX>; + clock-names = "clk"; + linux,rc-map-name = "rc-rc6-mce"; +}; diff --git a/Documentation/devicetree/bindings/media/rc.txt b/Documentation/devicetree/bindings/media/rc.txt new file mode 100644 index 000000000000..d3e7a012bfda --- /dev/null +++ b/Documentation/devicetree/bindings/media/rc.txt @@ -0,0 +1,117 @@ +The following properties are common to the infrared remote controllers: + +- linux,rc-map-name: string, specifies the scancode/key mapping table + defined in-kernel for the remote controller. Support values are: + * "rc-adstech-dvb-t-pci" + * "rc-alink-dtu-m" + * "rc-anysee" + * "rc-apac-viewcomp" + * "rc-asus-pc39" + * "rc-asus-ps3-100" + * "rc-ati-tv-wonder-hd-600" + * "rc-ati-x10" + * "rc-avermedia-a16d" + * "rc-avermedia-cardbus" + * "rc-avermedia-dvbt" + * "rc-avermedia-m135a" + * "rc-avermedia-m733a-rm-k6" + * "rc-avermedia-rm-ks" + * "rc-avermedia" + * "rc-avertv-303" + * "rc-azurewave-ad-tu700" + * "rc-behold-columbus" + * "rc-behold" + * "rc-budget-ci-old" + * "rc-cec" + * "rc-cinergy-1400" + * "rc-cinergy" + * "rc-delock-61959" + * "rc-dib0700-nec" + * "rc-dib0700-rc5" + * "rc-digitalnow-tinytwin" + * "rc-digittrade" + * "rc-dm1105-nec" + * "rc-dntv-live-dvbt-pro" + * "rc-dntv-live-dvb-t" + * "rc-dtt200u" + * "rc-dvbsky" + * "rc-empty" + * "rc-em-terratec" + * "rc-encore-enltv2" + * "rc-encore-enltv-fm53" + * "rc-encore-enltv" + * "rc-evga-indtube" + * "rc-eztv" + * "rc-flydvb" + * "rc-flyvideo" + * "rc-fusionhdtv-mce" + * "rc-gadmei-rm008z" + * "rc-geekbox" + * "rc-genius-tvgo-a11mce" + * "rc-gotview7135" + * "rc-hauppauge" + * "rc-imon-mce" + * "rc-imon-pad" + * "rc-iodata-bctv7e" + * "rc-it913x-v1" + * "rc-it913x-v2" + * "rc-kaiomy" + * "rc-kworld-315u" + * "rc-kworld-pc150u" + * "rc-kworld-plus-tv-analog" + * "rc-leadtek-y04g0051" + * "rc-lirc" + * "rc-lme2510" + * "rc-manli" + * "rc-medion-x10" + * "rc-medion-x10-digitainer" + * "rc-medion-x10-or2x" + * "rc-msi-digivox-ii" + * "rc-msi-digivox-iii" + * "rc-msi-tvanywhere-plus" + * "rc-msi-tvanywhere" + * "rc-nebula" + * "rc-nec-terratec-cinergy-xs" + * "rc-norwood" + * "rc-npgtech" + * "rc-pctv-sedna" + * "rc-pinnacle-color" + * "rc-pinnacle-grey" + * "rc-pinnacle-pctv-hd" + * "rc-pixelview-new" + * "rc-pixelview" + * "rc-pixelview-002t" + * "rc-pixelview-mk12" + * "rc-powercolor-real-angel" + * "rc-proteus-2309" + * "rc-purpletv" + * "rc-pv951" + * "rc-hauppauge" + * "rc-rc5-tv" + * "rc-rc6-mce" + * "rc-real-audio-220-32-keys" + * "rc-reddo" + * "rc-snapstream-firefly" + * "rc-streamzap" + * "rc-tbs-nec" + * "rc-technisat-ts35" + * "rc-technisat-usb2" + * "rc-terratec-cinergy-c-pci" + * "rc-terratec-cinergy-s2-hd" + * "rc-terratec-cinergy-xs" + * "rc-terratec-slim" + * "rc-terratec-slim-2" + * "rc-tevii-nec" + * "rc-tivo" + * "rc-total-media-in-hand" + * "rc-total-media-in-hand-02" + * "rc-trekstor" + * "rc-tt-1500" + * "rc-twinhan-dtv-cab-ci" + * "rc-twinhan1027" + * "rc-videomate-k100" + * "rc-videomate-s350" + * "rc-videomate-tv-pvr" + * "rc-winfast" + * "rc-winfast-usbii-deluxe" + * "rc-su3000" diff --git a/Documentation/devicetree/bindings/media/st,st-delta.txt b/Documentation/devicetree/bindings/media/st,st-delta.txt new file mode 100644 index 000000000000..a538ab30a617 --- /dev/null +++ b/Documentation/devicetree/bindings/media/st,st-delta.txt @@ -0,0 +1,17 @@ +* STMicroelectronics DELTA multi-format video decoder + +Required properties: +- compatible: should be "st,st-delta". +- clocks: from common clock binding: handle hardware IP needed clocks, the + number of clocks may depend on the SoC type. + See ../clock/clock-bindings.txt for details. +- clock-names: names of the clocks listed in clocks property in the same order. + +Example: + delta0 { + compatible = "st,st-delta"; + clock-names = "delta", "delta-st231", "delta-flash-promip"; + clocks = <&clk_s_c0_flexgen CLK_VID_DMU>, + <&clk_s_c0_flexgen CLK_ST231_DMU>, + <&clk_s_c0_flexgen CLK_FLASH_PROMIP>; + }; diff --git a/Documentation/devicetree/bindings/media/sunxi-ir.txt b/Documentation/devicetree/bindings/media/sunxi-ir.txt index 1811a067c72c..302a0b183cb8 100644 --- a/Documentation/devicetree/bindings/media/sunxi-ir.txt +++ b/Documentation/devicetree/bindings/media/sunxi-ir.txt @@ -9,7 +9,7 @@ Required properties: - reg : should contain IO map address for IR. Optional properties: -- linux,rc-map-name : Remote control map name. +- linux,rc-map-name: see rc.txt file in the same directory. - resets : phandle + reset specifier pair Example: diff --git a/Documentation/devicetree/bindings/media/ti,da850-vpif.txt b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt new file mode 100644 index 000000000000..6d25d7f23d26 --- /dev/null +++ b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt @@ -0,0 +1,83 @@ +Texas Instruments VPIF +---------------------- + +The TI Video Port InterFace (VPIF) is the primary component for video +capture and display on the DA850/AM18x family of TI DaVinci/Sitara +SoCs. + +TI Document reference: SPRUH82C, Chapter 35 +http://www.ti.com/lit/pdf/spruh82 + +Required properties: +- compatible: must be "ti,da850-vpif" +- reg: physical base address and length of the registers set for the device; +- interrupts: should contain IRQ line for the VPIF + +Video Capture: + +VPIF has a 16-bit parallel bus input, supporting 2 8-bit channels or a +single 16-bit channel. It should contain at least one port child node +with child 'endpoint' node. Please refer to the bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example using 2 8-bit input channels, one of which is connected to an +I2C-connected TVP5147 decoder: + + vpif: vpif@217000 { + compatible = "ti,da850-vpif"; + reg = <0x217000 0x1000>; + interrupts = <92>; + + port { + vpif_ch0: endpoint@0 { + reg = <0>; + bus-width = <8>; + remote-endpoint = <&composite>; + }; + + vpif_ch1: endpoint@1 { + reg = <1>; + bus-width = <8>; + data-shift = <8>; + }; + }; + }; + +[ ... ] + +&i2c0 { + + tvp5147@5d { + compatible = "ti,tvp5147"; + reg = <0x5d>; + status = "okay"; + + port { + composite: endpoint { + hsync-active = <1>; + vsync-active = <1>; + pclk-sample = <0>; + + /* VPIF channel 0 (lower 8-bits) */ + remote-endpoint = <&vpif_ch0>; + bus-width = <8>; + }; + }; + }; +}; + + +Alternatively, an example when the bus is configured as a single +16-bit input (e.g. for raw-capture mode): + + vpif: vpif@217000 { + compatible = "ti,da850-vpif"; + reg = <0x217000 0x1000>; + interrupts = <92>; + + port { + vpif_ch0: endpoint { + bus-width = <16>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mips/img/pistachio-marduk.txt b/Documentation/devicetree/bindings/mips/img/pistachio-marduk.txt new file mode 100644 index 000000000000..2d5126d529a2 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/img/pistachio-marduk.txt @@ -0,0 +1,10 @@ +Imagination Technologies' Pistachio SoC based Marduk Board +========================================================== + +Compatible string must be "img,pistachio-marduk", "img,pistachio" + +Hardware and other related documentation is available at +https://docs.creatordev.io/ci40/ + +It is also known as Creator Ci40. Marduk is legacy name and will +be there for decades. diff --git a/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt index 7f95ec400863..50bf611a4d2c 100644 --- a/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt +++ b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt @@ -17,7 +17,7 @@ Required properties: "core" - Main peripheral bus clock "clkin0" - Parent clock of internal mux "clkin1" - Other parent clock of internal mux - The driver has an interal mux clock which switches between clkin0 and clkin1 depending on the + The driver has an internal mux clock which switches between clkin0 and clkin1 depending on the clock rate requested by the MMC core. Example: diff --git a/Documentation/devicetree/bindings/mmc/mmc-pwrseq-sd8787.txt b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-sd8787.txt new file mode 100644 index 000000000000..22e9340e4ba2 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-sd8787.txt @@ -0,0 +1,16 @@ +* Marvell SD8787 power sequence provider + +Required properties: +- compatible: must be "mmc-pwrseq-sd8787". +- powerdown-gpios: contains a power down GPIO specifier with the + default active state +- reset-gpios: contains a reset GPIO specifier with the default + active state + +Example: + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-sd8787"; + powerdown-gpios = <&twl_gpio 0 GPIO_ACTIVE_LOW>; + reset-gpios = <&twl_gpio 1 GPIO_ACTIVE_LOW>; + } diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 8a377827695b..c7f4a0ec48ed 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -40,6 +40,7 @@ Optional properties: - cap-mmc-hw-reset: eMMC hardware reset is supported - cap-sdio-irq: enable SDIO IRQ signalling on this interface - full-pwr-cycle: full power cycle of the card is supported +- mmc-ddr-3_3v: eMMC high-speed DDR mode(3.3V I/O) is supported - mmc-ddr-1_8v: eMMC high-speed DDR mode(1.8V I/O) is supported - mmc-ddr-1_2v: eMMC high-speed DDR mode(1.2V I/O) is supported - mmc-hs200-1_8v: eMMC HS200 mode(1.8V I/O) is supported diff --git a/Documentation/devicetree/bindings/mmc/sdhci-st.txt b/Documentation/devicetree/bindings/mmc/sdhci-st.txt index 3cd4c43a3260..230fd696eb92 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-st.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-st.txt @@ -38,7 +38,7 @@ Optional properties: - bus-width: Number of data lines. See: Documentation/devicetree/bindings/mmc/mmc.txt. -- max-frequency: Can be 200MHz, 100Mz or 50MHz (default) and used for +- max-frequency: Can be 200MHz, 100MHz or 50MHz (default) and used for configuring the CCONFIG3 in the mmcss. See: Documentation/devicetree/bindings/mmc/mmc.txt. diff --git a/Documentation/devicetree/bindings/mmc/sdhci.txt b/Documentation/devicetree/bindings/mmc/sdhci.txt index 1c95a1a555c3..0e9923a64024 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci.txt @@ -5,7 +5,7 @@ host controllers refer to the mmc[1] bindings. Optional properties: - sdhci-caps-mask: The sdhci capabilities register is incorrect. This 64bit - property corresponds to the bits in the sdhci capabilty register. If the bit + property corresponds to the bits in the sdhci capability register. If the bit is on in the mask then the bit is incorrect in the register and should be turned off, before applying sdhci-caps. - sdhci-caps: The sdhci capabilities register is incorrect. This 64bit diff --git a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt index 55cdd804cdba..7d53a799f140 100644 --- a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt +++ b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt @@ -13,6 +13,7 @@ Required properties: * "allwinner,sun5i-a13-mmc" * "allwinner,sun7i-a20-mmc" * "allwinner,sun9i-a80-mmc" + * "allwinner,sun50i-a64-emmc" * "allwinner,sun50i-a64-mmc" - reg : mmc controller base registers - clocks : a list with 4 phandle + clock specifier pairs diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt index 7fd17c3da116..9cb55ca57461 100644 --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt @@ -16,7 +16,7 @@ Required Properties: each child-node representing a supported slot. There should be atleast one child node representing a card slot. The name of the child node representing the slot is recommended to be slot@n where n is the unique number of the slot - connnected to the controller. The following are optional properties which + connected to the controller. The following are optional properties which can be included in the slot child node. * reg: specifies the physical slot number. The valid values of this @@ -75,6 +75,17 @@ Optional properties: * card-detect-delay: Delay in milli-seconds before detecting card after card insert event. The default value is 0. +* data-addr: Override fifo address with value provided by DT. The default FIFO reg + offset is assumed as 0x100 (version < 0x240A) and 0x200(version >= 0x240A) by + driver. If the controller does not follow this rule, please use this property + to set fifo address in device tree. + +* fifo-watermark-aligned: Data done irq is expected if data length is less than + watermark in PIO mode. But fifo watermark is requested to be aligned with data + length in some SoC so that TX/RX irq can be generated with data done irq. Add this + watermark quirk to mark this requirement and force fifo watermark setting + accordingly. + * vmmc-supply: The phandle to the regulator to use for vmmc. If this is specified we'll defer probe until we can find this regulator. @@ -102,6 +113,8 @@ board specific portions as listed below. interrupts = <0 75 0>; #address-cells = <1>; #size-cells = <0>; + data-addr = <0x200>; + fifo-watermark-aligned; resets = <&rst 20>; reset-names = "reset"; }; diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index a1650edfd2b7..4fd8b7acc510 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -25,6 +25,19 @@ Required properties: "renesas,sdhi-r8a7795" - SDHI IP on R8A7795 SoC "renesas,sdhi-r8a7796" - SDHI IP on R8A7796 SoC +- clocks: Most controllers only have 1 clock source per channel. However, on + some variations of this controller, the internal card detection + logic that exists in this controller is sectioned off to be run by a + separate second clock source to allow the main core clock to be turned + off to save power. + If 2 clocks are specified by the hardware, you must name them as + "core" and "cd". If the controller only has 1 clock, naming is not + required. + Below is the number clocks for each supported SoC: + 1: SH73A0, R8A73A4, R8A7740, R8A7778, R8A7779, R8A7790 + R8A7791, R8A7792, R8A7793, R8A7794, R8A7795, R8A7796 + 2: R7S72100 + Optional properties: - toshiba,mmc-wrprotect-disable: write-protect detection is unavailable - pinctrl-names: should be "default", "state_uhs" diff --git a/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt new file mode 100644 index 000000000000..eaade0e5adeb --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt @@ -0,0 +1,33 @@ +* ZTE specific extensions to the Synopsys Designware Mobile Storage + Host Controller + +The Synopsys designware mobile storage host controller is used to interface +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents +differences between the core Synopsys dw mshc controller properties described +by synopsys-dw-mshc.txt and the properties used by the ZTE specific +extensions to the Synopsys Designware Mobile Storage Host Controller. + +Required Properties: + +* compatible: should be + - "zte,zx296718-dw-mshc": for ZX SoCs + +Example: + + mmc1: mmc@1110000 { + compatible = "zte,zx296718-dw-mshc"; + reg = <0x01110000 0x1000>; + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; + fifo-depth = <32>; + data-addr = <0x200>; + fifo-watermark-aligned; + bus-width = <4>; + clock-frequency = <50000000>; + clocks = <&topcrm SD0_AHB>, <&topcrm SD0_WCLK>; + clock-names = "biu", "ciu"; + num-slots = <1>; + max-frequency = <50000000>; + cap-sdio-irq; + cap-sd-highspeed; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/mtd/aspeed-smc.txt b/Documentation/devicetree/bindings/mtd/aspeed-smc.txt new file mode 100644 index 000000000000..49f6528ef547 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/aspeed-smc.txt @@ -0,0 +1,51 @@ +* Aspeed Firmware Memory controller +* Aspeed SPI Flash Memory Controller + +The Firmware Memory Controller in the Aspeed AST2500 SoC supports +three chip selects, two of which are always of SPI type and the third +can be SPI or NOR type flash. These bindings only describe SPI. + +The two SPI flash memory controllers in the AST2500 each support two +chip selects. + +Required properties: + - compatible : Should be one of + "aspeed,ast2400-fmc" for the AST2400 Firmware Memory Controller + "aspeed,ast2400-spi" for the AST2400 SPI Flash memory Controller + "aspeed,ast2500-fmc" for the AST2500 Firmware Memory Controller + "aspeed,ast2500-spi" for the AST2500 SPI flash memory controllers + + - reg : the first contains the control register location and length, + the second contains the memory window mapping address and length + - #address-cells : must be 1 corresponding to chip select child binding + - #size-cells : must be 0 corresponding to chip select child binding + +Optional properties: + - interrupts : Should contain the interrupt for the dma device if an + FMC + +The child nodes are the SPI flash modules which must have a compatible +property as specified in bindings/mtd/jedec,spi-nor.txt + +Optionally, the child node can contain properties for SPI mode (may be +ignored): + - spi-max-frequency - max frequency of spi bus + + +Example: +fmc: fmc@1e620000 { + compatible = "aspeed,ast2500-fmc"; + reg = < 0x1e620000 0x94 + 0x20000000 0x02000000 >; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <19>; + flash@0 { + reg = < 0 >; + compatible = "jedec,spi-nor"; + /* spi-max-frequency = <>; */ + /* m25p,fast-read; */ + #address-cells = <1>; + #size-cells = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/common.txt b/Documentation/devicetree/bindings/mtd/common.txt new file mode 100644 index 000000000000..fc068b923d7a --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/common.txt @@ -0,0 +1,15 @@ +* Common properties of all MTD devices + +Optional properties: +- label: user-defined MTD device name. Can be used to assign user + friendly names to MTD devices (instead of the flash model or flash + controller based name) in order to ease flash device identification + and/or describe what they are used for. + +Example: + + flash@0 { + label = "System-firmware"; + + /* flash type specific properties */ + }; diff --git a/Documentation/devicetree/bindings/mtd/cortina,gemini-flash.txt b/Documentation/devicetree/bindings/mtd/cortina,gemini-flash.txt new file mode 100644 index 000000000000..3fa1b34d69ad --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/cortina,gemini-flash.txt @@ -0,0 +1,24 @@ +Flash device on Cortina Systems Gemini SoC + +This flash is regular CFI compatible (Intel or AMD extended) flash chips with +some special bits that can be controlled by the machine's system controller. + +Required properties: +- compatible : must be "cortina,gemini-flash", "cfi-flash"; +- reg : memory address for the flash chip +- syscon : must be a phandle to the system controller +- bank-width : width in bytes of flash interface, should be <2> + +For the rest of the properties, see mtd-physmap.txt. + +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + +Example: + +flash@30000000 { + compatible = "cortina,gemini-flash", "cfi-flash"; + reg = <0x30000000 0x01000000>; + syscon = <&syscon>; + bank-width = <2>; +}; diff --git a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt index 2c91c03e7eb0..3e920ec5c4d3 100644 --- a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt +++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt @@ -14,6 +14,8 @@ Required properties: at25df641 at26df081a mr25h256 + mr25h10 + mr25h40 mx25l4005a mx25l1606e mx25l6405d diff --git a/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt b/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt index fb314f09861b..5ded66ad7aef 100644 --- a/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt +++ b/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt @@ -1,7 +1,13 @@ * Serial NOR flash controller for MTK MT81xx (and similar) Required properties: -- compatible: should be "mediatek,mt8173-nor"; +- compatible: The possible values are: + "mediatek,mt2701-nor" + "mediatek,mt7623-nor" + "mediatek,mt8173-nor" + For mt8173, compatible should be "mediatek,mt8173-nor". + For every other SoC, should contain both the SoC-specific compatible string + and "mediatek,mt8173-nor". - reg: physical base address and length of the controller's register - clocks: the phandle of the clocks needed by the nor controller - clock-names: the names of the clocks diff --git a/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt b/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt index 980b16df74c3..0854451ff91d 100644 --- a/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt +++ b/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt @@ -1,4 +1,4 @@ -Marvell 8897/8997 (sd8897/sd8997/pcie8997) SDIO/PCIE devices +Marvell 8787/8897/8997 (sd8787/sd8897/sd8997/pcie8997) SDIO/PCIE devices ------ This node provides properties for controlling the Marvell SDIO/PCIE wireless device. @@ -8,6 +8,7 @@ connects the device to the system. Required properties: - compatible : should be one of the following: + * "marvell,sd8787" * "marvell,sd8897" * "marvell,sd8997" * "pci11ab,2b42" @@ -34,6 +35,9 @@ Optional properties: so that the wifi chip can wakeup host platform under certain condition. during system resume, the irq will be disabled to make sure unnecessary interrupt is not received. + - vmmc-supply: a phandle of a regulator, supplying VCC to the card + - mmc-pwrseq: phandle to the MMC power sequence node. See "mmc-pwrseq-*" + for documentation of MMC power sequence bindings. Example: @@ -46,6 +50,7 @@ so that firmware can wakeup host using this device side pin. &mmc3 { status = "okay"; vmmc-supply = <&wlan_en_reg>; + mmc-pwrseq = <&wifi_pwrseq>; bus-width = <4>; cap-power-off-card; keep-power-in-suspend; diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index de1378b4efad..7c85dca4221a 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -23,6 +23,7 @@ Required properties: "allwinner,sun8i-h3-pinctrl" "allwinner,sun8i-h3-r-pinctrl" "allwinner,sun50i-a64-pinctrl" + "allwinner,sun50i-h5-r-pinctrl" "nextthing,gr8-pinctrl" - reg: Should contain the register physical address and length for the diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt index 457b2c68d47b..8c5d27c5b562 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt @@ -19,7 +19,7 @@ iomuxc: iomuxc@30330000 { reg = <0x30330000 0x10000>; }; -Pheriparials using pads from iomuxc-lpsr support low state retention power +Peripherals using pads from iomuxc-lpsr support low state retention power state, under LPSR mode GPIO's state of pads are retain. Please refer to fsl,imx-pinctrl.txt in this directory for common binding part diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt new file mode 100644 index 000000000000..97aef67ee769 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt @@ -0,0 +1,46 @@ +* Marvell 98dx3236 pinctrl driver for mpp + +Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding +part and usage + +Required properties: +- compatible: "marvell,98dx3236-pinctrl" or "marvell,98dx4251-pinctrl" +- reg: register specifier of MPP registers + +This driver supports all 98dx3236, 98dx3336 and 98dx4251 variants + +name pins functions +================================================================================ +mpp0 0 gpo, spi0(mosi), dev(ad8) +mpp1 1 gpio, spi0(miso), dev(ad9) +mpp2 2 gpo, spi0(sck), dev(ad10) +mpp3 3 gpio, spi0(cs0), dev(ad11) +mpp4 4 gpio, spi0(cs1), smi(mdc), dev(cs0) +mpp5 5 gpio, pex(rsto), sd0(cmd), dev(bootcs) +mpp6 6 gpo, sd0(clk), dev(a2) +mpp7 7 gpio, sd0(d0), dev(ale0) +mpp8 8 gpio, sd0(d1), dev(ale1) +mpp9 9 gpio, sd0(d2), dev(ready0) +mpp10 10 gpio, sd0(d3), dev(ad12) +mpp11 11 gpio, uart1(rxd), uart0(cts), dev(ad13) +mpp12 12 gpo, uart1(txd), uart0(rts), dev(ad14) +mpp13 13 gpio, intr(out), dev(ad15) +mpp14 14 gpio, i2c0(sck) +mpp15 15 gpio, i2c0(sda) +mpp16 16 gpo, dev(oe) +mpp17 17 gpo, dev(clkout) +mpp18 18 gpio, uart1(txd) +mpp19 19 gpio, uart1(rxd), dev(rb) +mpp20 20 gpo, dev(we0) +mpp21 21 gpo, dev(ad0) +mpp22 22 gpo, dev(ad1) +mpp23 23 gpo, dev(ad2) +mpp24 24 gpo, dev(ad3) +mpp25 25 gpo, dev(ad4) +mpp26 26 gpo, dev(ad5) +mpp27 27 gpo, dev(ad6) +mpp28 28 gpo, dev(ad7) +mpp29 29 gpo, dev(a0) +mpp30 30 gpo, dev(a1) +mpp31 31 gpio, slv_smi(mdc), smi(mdc), dev(we1) +mpp32 32 gpio, slv_smi(mdio), smi(mdio), dev(cs1) diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt index 730444a9a4de..6c0ea155b708 100644 --- a/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt @@ -44,16 +44,16 @@ mpp16 16 gpio, sdio(d2), uart0(cts), uart1(rxd), mii(crs) mpp17 17 gpio, sdio(d3) mpp18 18 gpo, nand(io0) mpp19 19 gpo, nand(io1) -mpp20 20 gpio, mii(rxerr) -mpp21 21 gpio, audio(spdifi) -mpp22 22 gpio, audio(spdifo) -mpp23 23 gpio, audio(rmclk) -mpp24 24 gpio, audio(bclk) -mpp25 25 gpio, audio(sdo) -mpp26 26 gpio, audio(lrclk) -mpp27 27 gpio, audio(mclk) -mpp28 28 gpio, audio(sdi) -mpp29 29 gpio, audio(extclk) +mpp35 35 gpio, mii(rxerr) +mpp36 36 gpio, audio(spdifi) +mpp37 37 gpio, audio(spdifo) +mpp38 38 gpio, audio(rmclk) +mpp39 39 gpio, audio(bclk) +mpp40 40 gpio, audio(sdo) +mpp41 41 gpio, audio(lrclk) +mpp42 42 gpio, audio(mclk) +mpp43 43 gpio, audio(sdi) +mpp44 44 gpio, audio(extclk) * Marvell Kirkwood 88f6190 diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt index 2ad18c4ea55c..b98e6f030da8 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt @@ -1,25 +1,38 @@ +====================== Aspeed Pin Controllers ----------------------- +====================== The Aspeed SoCs vary in functionality inside a generation but have a common mux device register layout. -Required properties: -- compatible : Should be any one of the following: - "aspeed,ast2400-pinctrl" - "aspeed,g4-pinctrl" - "aspeed,ast2500-pinctrl" - "aspeed,g5-pinctrl" +Required properties for g4: +- compatible : Should be one of the following: + "aspeed,ast2400-pinctrl" + "aspeed,g4-pinctrl" -The pin controller node should be a child of a syscon node with the required +Required properties for g5: +- compatible : Should be one of the following: + "aspeed,ast2500-pinctrl" + "aspeed,g5-pinctrl" + +- aspeed,external-nodes: A cell of phandles to external controller nodes: + 0: compatible with "aspeed,ast2500-gfx", "syscon" + 1: compatible with "aspeed,ast2500-lhc", "syscon" + +The pin controller node should be the child of a syscon node with the required property: -- compatible: "syscon", "simple-mfd" + +- compatible : Should be one of the following: + "aspeed,ast2400-scu", "syscon", "simple-mfd" + "aspeed,g4-scu", "syscon", "simple-mfd" + "aspeed,ast2500-scu", "syscon", "simple-mfd" + "aspeed,g5-scu", "syscon", "simple-mfd" Refer to the the bindings described in Documentation/devicetree/bindings/mfd/syscon.txt Subnode Format --------------- +============== The required properties of child nodes are (as defined in pinctrl-bindings): - function @@ -31,26 +44,43 @@ supported: aspeed,ast2400-pinctrl, aspeed,g4-pinctrl: -ACPI BMCINT DDCCLK DDCDAT FLACK FLBUSY FLWP GPID0 GPIE0 GPIE2 GPIE4 GPIE6 I2C10 -I2C11 I2C12 I2C13 I2C3 I2C4 I2C5 I2C6 I2C7 I2C8 I2C9 LPCPD LPCPME LPCSMI MDIO1 -MDIO2 NCTS1 NCTS3 NCTS4 NDCD1 NDCD3 NDCD4 NDSR1 NDSR3 NDTR1 NDTR3 NRI1 NRI3 -NRI4 NRTS1 NRTS3 PWM0 PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 RGMII1 RMII1 ROM16 -ROM8 ROMCS1 ROMCS2 ROMCS3 ROMCS4 RXD1 RXD3 RXD4 SD1 SGPMI SIOPBI SIOPBO TIMER3 -TIMER5 TIMER6 TIMER7 TIMER8 TXD1 TXD3 TXD4 UART6 VGAHS VGAVS VPI18 VPI24 VPI30 -VPO12 VPO24 +ACPI ADC0 ADC1 ADC10 ADC11 ADC12 ADC13 ADC14 ADC15 ADC2 ADC3 ADC4 ADC5 ADC6 +ADC7 ADC8 ADC9 BMCINT DDCCLK DDCDAT EXTRST FLACK FLBUSY FLWP GPID GPID0 GPID2 +GPID4 GPID6 GPIE0 GPIE2 GPIE4 GPIE6 I2C10 I2C11 I2C12 I2C13 I2C14 I2C3 I2C4 +I2C5 I2C6 I2C7 I2C8 I2C9 LPCPD LPCPME LPCRST LPCSMI MAC1LINK MAC2LINK MDIO1 +MDIO2 NCTS1 NCTS2 NCTS3 NCTS4 NDCD1 NDCD2 NDCD3 NDCD4 NDSR1 NDSR2 NDSR3 NDSR4 +NDTR1 NDTR2 NDTR3 NDTR4 NDTS4 NRI1 NRI2 NRI3 NRI4 NRTS1 NRTS2 NRTS3 OSCCLK PWM0 +PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 RGMII1 RGMII2 RMII1 RMII2 ROM16 ROM8 ROMCS1 +ROMCS2 ROMCS3 ROMCS4 RXD1 RXD2 RXD3 RXD4 SALT1 SALT2 SALT3 SALT4 SD1 SD2 SGPMCK +SGPMI SGPMLD SGPMO SGPSCK SGPSI0 SGPSI1 SGPSLD SIOONCTRL SIOPBI SIOPBO SIOPWREQ +SIOPWRGD SIOS3 SIOS5 SIOSCI SPI1 SPI1DEBUG SPI1PASSTHRU SPICS1 TIMER3 TIMER4 +TIMER5 TIMER6 TIMER7 TIMER8 TXD1 TXD2 TXD3 TXD4 UART6 USBCKI VGABIOS_ROM VGAHS +VGAVS VPI18 VPI24 VPI30 VPO12 VPO24 WDTRST1 WDTRST2 aspeed,ast2500-pinctrl, aspeed,g5-pinctrl: -GPID0 GPID2 GPIE0 I2C10 I2C11 I2C12 I2C13 I2C14 I2C3 I2C4 I2C5 I2C6 I2C7 I2C8 -I2C9 MAC1LINK MDIO1 MDIO2 OSCCLK PEWAKE PWM0 PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 -RGMII1 RGMII2 RMII1 RMII2 SD1 SPI1 SPI1DEBUG SPI1PASSTHRU TIMER4 TIMER5 TIMER6 -TIMER7 TIMER8 VGABIOSROM - - -Examples: +ACPI ADC0 ADC1 ADC10 ADC11 ADC12 ADC13 ADC14 ADC15 ADC2 ADC3 ADC4 ADC5 ADC6 +ADC7 ADC8 ADC9 BMCINT DDCCLK DDCDAT ESPI FWSPICS1 FWSPICS2 GPID0 GPID2 GPID4 +GPID6 GPIE0 GPIE2 GPIE4 GPIE6 I2C10 I2C11 I2C12 I2C13 I2C14 I2C3 I2C4 I2C5 I2C6 +I2C7 I2C8 I2C9 LAD0 LAD1 LAD2 LAD3 LCLK LFRAME LPCHC LPCPD LPCPLUS LPCPME +LPCRST LPCSMI LSIRQ MAC1LINK MAC2LINK MDIO1 MDIO2 NCTS1 NCTS2 NCTS3 NCTS4 NDCD1 +NDCD2 NDCD3 NDCD4 NDSR1 NDSR2 NDSR3 NDSR4 NDTR1 NDTR2 NDTR3 NDTR4 NRI1 NRI2 +NRI3 NRI4 NRTS1 NRTS2 NRTS3 NRTS4 OSCCLK PEWAKE PNOR PWM0 PWM1 PWM2 PWM3 PWM4 +PWM5 PWM6 PWM7 RGMII1 RGMII2 RMII1 RMII2 RXD1 RXD2 RXD3 RXD4 SALT1 SALT10 +SALT11 SALT12 SALT13 SALT14 SALT2 SALT3 SALT4 SALT5 SALT6 SALT7 SALT8 SALT9 +SCL1 SCL2 SD1 SD2 SDA1 SDA2 SGPS1 SGPS2 SIOONCTRL SIOPBI SIOPBO SIOPWREQ +SIOPWRGD SIOS3 SIOS5 SIOSCI SPI1 SPI1CS1 SPI1DEBUG SPI1PASSTHRU SPI2CK SPI2CS0 +SPI2CS1 SPI2MISO SPI2MOSI TIMER3 TIMER4 TIMER5 TIMER6 TIMER7 TIMER8 TXD1 TXD2 +TXD3 TXD4 UART6 USBCKI VGABIOSROM VGAHS VGAVS VPI24 VPO WDTRST1 WDTRST2 + +Examples +======== + +g4 Example +---------- syscon: scu@1e6e2000 { - compatible = "syscon", "simple-mfd"; + compatible = "aspeed,ast2400-scu", "syscon", "simple-mfd"; reg = <0x1e6e2000 0x1a8>; pinctrl: pinctrl { @@ -63,5 +93,56 @@ syscon: scu@1e6e2000 { }; }; +g5 Example +---------- + +ahb { + apb { + syscon: scu@1e6e2000 { + compatible = "aspeed,ast2500-scu", "syscon", "simple-mfd"; + reg = <0x1e6e2000 0x1a8>; + + pinctrl: pinctrl { + compatible = "aspeed,g5-pinctrl"; + aspeed,external-nodes = <&gfx &lhc>; + + pinctrl_i2c3_default: i2c3_default { + function = "I2C3"; + groups = "I2C3"; + }; + }; + }; + + gfx: display@1e6e6000 { + compatible = "aspeed,ast2500-gfx", "syscon"; + reg = <0x1e6e6000 0x1000>; + }; + }; + + lpc: lpc@1e789000 { + compatible = "aspeed,ast2500-lpc", "simple-mfd"; + reg = <0x1e789000 0x1000>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x1e789000 0x1000>; + + lpc_host: lpc-host@80 { + compatible = "aspeed,ast2500-lpc-host", "simple-mfd", "syscon"; + reg = <0x80 0x1e0>; + reg-io-width = <4>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x80 0x1e0>; + + lhc: lhc@20 { + compatible = "aspeed,ast2500-lhc"; + reg = <0x20 0x24 0x48 0x8>; + }; + }; + }; +}; + Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices. diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt index 1baf19eecabf..5e00a21de2bf 100644 --- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt @@ -13,6 +13,7 @@ Required Properties: - "samsung,s3c2450-pinctrl": for S3C2450-compatible pin-controller, - "samsung,s3c64xx-pinctrl": for S3C64xx-compatible pin-controller, - "samsung,s5pv210-pinctrl": for S5PV210-compatible pin-controller, + - "samsung,exynos3250-pinctrl": for Exynos3250 compatible pin-controller. - "samsung,exynos4210-pinctrl": for Exynos4210 compatible pin-controller. - "samsung,exynos4x12-pinctrl": for Exynos4x12 compatible pin-controller. - "samsung,exynos5250-pinctrl": for Exynos5250 compatible pin-controller. diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt index b24583aa34c3..eac20aa33907 100644 --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt @@ -8,8 +8,9 @@ controllers onto these pads. Pin controller node: Required properies: - compatible: value should be one of the following: - (a) "st,stm32f429-pinctrl" - (b) "st,stm32f746-pinctrl" + "st,stm32f429-pinctrl" + "st,stm32f746-pinctrl" + "st,stm32h743-pinctrl" - #address-cells: The value of this property must be 1 - #size-cells : The value of this property must be 1 - ranges : defines mapping between pin controller node (parent) to @@ -37,8 +38,23 @@ Optional properties: - st,syscfg: Should be phandle/offset pair. The phandle to the syscon node which includes IRQ mux selection register, and the offset of the IRQ mux selection register. + - ngpios: Number of gpios in a bank (to use if bank gpio numbers is less + than 16). + - gpio-ranges: Define a dedicated mapping between a pin-controller and + a gpio controller. Format is <&phandle a b c> with: + -(phandle): phandle of pin-controller. + -(a): gpio base offset in range. + -(b): pin base offset in range. + -(c): gpio count in range + This entry has to be used either if there are holes inside a bank: + GPIOB0/B1/B2/B14/B15 (see example 2) + or if banks are not contiguous: + GPIOA/B/C/E... + NOTE: If "gpio-ranges" is used for a gpio controller, all gpio-controller + have to use a "gpio-ranges" entry. + More details in Documentation/devicetree/bindings/gpio/gpio.txt. -Example: +Example 1: #include <dt-bindings/pinctrl/stm32f429-pinfunc.h> ... @@ -60,6 +76,43 @@ Example: pin-functions nodes follow... }; +Example 2: +#include <dt-bindings/pinctrl/stm32f429-pinfunc.h> +... + + pinctrl: pin-controller { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,stm32f429-pinctrl"; + ranges = <0 0x40020000 0x3000>; + pins-are-numbered; + + gpioa: gpio@40020000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x0 0x400>; + resets = <&reset_ahb1 0>; + st,bank-name = "GPIOA"; + gpio-ranges = <&pinctrl 0 0 16>; + }; + + gpiob: gpio@40020400 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x0 0x400>; + resets = <&reset_ahb1 0>; + st,bank-name = "GPIOB"; + ngpios = 4; + gpio-ranges = <&pinctrl 0 16 3>, + <&pinctrl 14 30 2>; + }; + + + ... + pin-functions nodes follow... + }; + + Contents of function subnode node: ---------------------------------- Subnode format diff --git a/Documentation/devicetree/bindings/pinctrl/ti,iodelay.txt b/Documentation/devicetree/bindings/pinctrl/ti,iodelay.txt new file mode 100644 index 000000000000..c3ed1232b6a3 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/ti,iodelay.txt @@ -0,0 +1,47 @@ +* Pin configuration for TI IODELAY controller + +TI dra7 based SoCs such as am57xx have a controller for setting the IO delay +for each pin. For most part the IO delay values are programmed by the bootloader, +but some pins need to be configured dynamically by the kernel such as the +MMC pins. + +Required Properties: + + - compatible: Must be "ti,dra7-iodelay" + - reg: Base address and length of the memory resource used + - #address-cells: Number of address cells + - #size-cells: Size of cells + - #pinctrl-cells: Number of pinctrl cells, must be 2. See also + Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +Example +------- + +In the SoC specific dtsi file: + + dra7_iodelay_core: padconf@4844a000 { + compatible = "ti,dra7-iodelay"; + reg = <0x4844a000 0x0d1c>; + #address-cells = <1>; + #size-cells = <0>; + #pinctrl-cells = <2>; + }; + +In board-specific file: + +&dra7_iodelay_core { + mmc2_iodelay_3v3_conf: mmc2_iodelay_3v3_conf { + pinctrl-pin-array = < + 0x18c A_DELAY_PS(0) G_DELAY_PS(120) /* CFG_GPMC_A19_IN */ + 0x1a4 A_DELAY_PS(265) G_DELAY_PS(360) /* CFG_GPMC_A20_IN */ + 0x1b0 A_DELAY_PS(0) G_DELAY_PS(120) /* CFG_GPMC_A21_IN */ + 0x1bc A_DELAY_PS(0) G_DELAY_PS(120) /* CFG_GPMC_A22_IN */ + 0x1c8 A_DELAY_PS(287) G_DELAY_PS(420) /* CFG_GPMC_A23_IN */ + 0x1d4 A_DELAY_PS(144) G_DELAY_PS(240) /* CFG_GPMC_A24_IN */ + 0x1e0 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_GPMC_A25_IN */ + 0x1ec A_DELAY_PS(120) G_DELAY_PS(0) /* CFG_GPMC_A26_IN */ + 0x1f8 A_DELAY_PS(120) G_DELAY_PS(180) /* CFG_GPMC_A27_IN */ + 0x360 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_GPMC_CS1_IN */ + >; + }; +}; diff --git a/Documentation/devicetree/bindings/power/supply/axp20x_ac_power.txt b/Documentation/devicetree/bindings/power/supply/axp20x_ac_power.txt new file mode 100644 index 000000000000..826e8a879121 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/axp20x_ac_power.txt @@ -0,0 +1,22 @@ +AXP20X and AXP22X PMICs' AC power supply + +Required Properties: + - compatible: One of: + "x-powers,axp202-ac-power-supply" + "x-powers,axp221-ac-power-supply" + +This node is a subnode of the axp20x PMIC. + +The AXP20X can read the current current and voltage supplied by AC by +reading ADC channels from the AXP20X ADC. + +The AXP22X is only able to tell if an AC power supply is present and +usable. + +Example: + +&axp209 { + ac_power_supply: ac-power-supply { + compatible = "x-powers,axp202-ac-power-supply"; + }; +}; diff --git a/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt b/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt index f1d7beec45bf..ba8d35f66cbe 100644 --- a/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt +++ b/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt @@ -3,6 +3,11 @@ AXP20x USB power supply Required Properties: -compatible: One of: "x-powers,axp202-usb-power-supply" "x-powers,axp221-usb-power-supply" + "x-powers,axp223-usb-power-supply" + +The AXP223 PMIC shares most of its behaviour with the AXP221 but has slight +variations such as the former being able to set the VBUS power supply max +current to 100mA, unlike the latter. This node is a subnode of the axp20x PMIC. diff --git a/Documentation/devicetree/bindings/power/supply/bq27xxx.txt b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt new file mode 100644 index 000000000000..b0c95ef63e68 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt @@ -0,0 +1,36 @@ +Binding for TI BQ27XXX fuel gauge family + +Required properties: +- compatible: Should contain one of the following: + * "ti,bq27200" - BQ27200 + * "ti,bq27210" - BQ27210 + * "ti,bq27500" - deprecated, use revision specific property below + * "ti,bq27510" - deprecated, use revision specific property below + * "ti,bq27520" - deprecated, use revision specific property below + * "ti,bq27500-1" - BQ27500/1 + * "ti,bq27510g1" - BQ27510-g1 + * "ti,bq27510g2" - BQ27510-g2 + * "ti,bq27510g3" - BQ27510-g3 + * "ti,bq27520g1" - BQ27520-g1 + * "ti,bq27520g2" - BQ27520-g2 + * "ti,bq27520g3" - BQ27520-g3 + * "ti,bq27520g4" - BQ27520-g4 + * "ti,bq27530" - BQ27530 + * "ti,bq27531" - BQ27531 + * "ti,bq27541" - BQ27541 + * "ti,bq27542" - BQ27542 + * "ti,bq27546" - BQ27546 + * "ti,bq27742" - BQ27742 + * "ti,bq27545" - BQ27545 + * "ti,bq27421" - BQ27421 + * "ti,bq27425" - BQ27425 + * "ti,bq27441" - BQ27441 + * "ti,bq27621" - BQ27621 +- reg: integer, i2c address of the device. + +Example: + +bq27510g3 { + compatible = "ti,bq27510g3"; + reg = <0x55>; +}; diff --git a/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt b/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt index 65b88fac854b..06f8a5ddb68e 100644 --- a/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt +++ b/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt @@ -105,6 +105,22 @@ PROPERTIES regulation must be done externally to fully comply with the JEITA safety guidelines if this flag is set. +- usb_otg_in-supply: + Usage: optional + Value type: <phandle> + Description: Reference to the regulator supplying power to the USB_OTG_IN + pin. + +child nodes: +- otg-vbus: + Usage: optional + Description: This node defines a regulator used to control the direction + of VBUS voltage - specifically: whether to supply voltage + to VBUS for host mode operation of the OTG port, or allow + input voltage from external VBUS for charging. In the + hardware, the supply for this regulator comes from + usb_otg_in-supply. + EXAMPLE charger@1000 { compatible = "qcom,pm8941-charger"; @@ -128,4 +144,7 @@ charger@1000 { qcom,fast-charge-current-limit = <1000000>; qcom,dc-charge-current-limit = <1000000>; + usb_otg_in-supply = <&pm8941_5vs1>; + + otg-vbus {}; }; diff --git a/Documentation/devicetree/bindings/power/supply/sbs_sbs-charger.txt b/Documentation/devicetree/bindings/power/supply/sbs_sbs-charger.txt new file mode 100644 index 000000000000..a3719623a94f --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/sbs_sbs-charger.txt @@ -0,0 +1,23 @@ +SBS sbs-charger +~~~~~~~~~~ + +Required properties: + - compatible: "<vendor>,<part-number>", "sbs,sbs-charger" as fallback. The part + number compatible string might be used in order to take care of vendor + specific registers. + +Optional properties: +- interrupt-parent: Should be the phandle for the interrupt controller. Use in + conjunction with "interrupts". +- interrupts: Interrupt mapping for GPIO IRQ. Use in conjunction with + "interrupt-parent". If an interrupt is not provided the driver will switch + automatically to polling. + +Example: + + ltc4100@9 { + compatible = "lltc,ltc4100", "sbs,sbs-charger"; + reg = <0x9>; + interrupt-parent = <&gpio6>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt b/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt index 3bf55757ceec..de45e1a2a4d9 100644 --- a/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt +++ b/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt @@ -8,8 +8,10 @@ Optional properties : - interrupts : Specify the interrupt to be used to trigger when the AC adapter is either plugged in or removed. - ti,ac-detect-gpios : This GPIO is optionally used to read the AC adapter - presence. This is a Host GPIO that is configured as an input and - connected to the bq24735. + status. This is a Host GPIO that is configured as an input and connected + to the ACOK pin on the bq24735. Note: for backwards compatibility reasons, + the GPIO must be active on AC adapter absence despite ACOK being active + (high) on AC adapter presence. - ti,charge-current : Used to control and set the charging current. This value must be between 128mA and 8.128A with a 64mA step resolution. The POR value is 0x0000h. This number is in mA (e.g. 8192), see spec for more information @@ -25,6 +27,8 @@ Optional properties : - ti,external-control : Indicates that the charger is configured externally and that the host should not attempt to enable/disable charging or set the charge voltage/current. + - poll-interval : In case 'interrupts' is not specified, poll AC adapter + presence with this interval (milliseconds). Example: diff --git a/Documentation/devicetree/bindings/power_supply/maxim,max14656.txt b/Documentation/devicetree/bindings/power_supply/maxim,max14656.txt new file mode 100644 index 000000000000..e03e85ae6572 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/maxim,max14656.txt @@ -0,0 +1,25 @@ +Maxim MAX14656 / AL32 USB Charger Detector + +Required properties : +- compatible : "maxim,max14656"; +- reg: i2c slave address +- interrupt-parent: the phandle for the interrupt controller +- interrupts: interrupt line + +Example: + +&i2c2 { + clock-frequency = <50000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + max14656@35 { + compatible = "maxim,max14656"; + reg = <0x35>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_charger_detect>; + interrupt-parent = <&gpio6>; + interrupts = <26 IRQ_TYPE_LEVEL_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/regulator/anatop-regulator.txt b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt index 37c4ea076f88..1d58c8cfdbc0 100644 --- a/Documentation/devicetree/bindings/regulator/anatop-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt @@ -14,6 +14,7 @@ Optional properties: - anatop-delay-bit-shift: Bit shift for the step time register - anatop-delay-bit-width: Number of bits used in the step time register - vin-supply: The supply for this regulator +- anatop-enable-bit: Regulator enable bit offset Any property defined as part of the core regulator binding, defined in regulator.txt, can also be used. diff --git a/Documentation/devicetree/bindings/regulator/cpcap-regulator.txt b/Documentation/devicetree/bindings/regulator/cpcap-regulator.txt new file mode 100644 index 000000000000..675f4437ce92 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/cpcap-regulator.txt @@ -0,0 +1,34 @@ +Motorola CPCAP PMIC voltage regulators +------------------------------------ + +Requires node properties: +- "compatible" value one of: + "motorola,cpcap-regulator" + "motorola,mapphone-cpcap-regulator" + +Required regulator properties: +- "regulator-name" +- "regulator-enable-ramp-delay" +- "regulator-min-microvolt" +- "regulator-max-microvolt" + +Optional regulator properties: +- "regulator-boot-on" + +See Documentation/devicetree/bindings/regulator/regulator.txt +for more details about the regulator properties. + +Example: + +cpcap_regulator: regulator { + compatible = "motorola,cpcap-regulator"; + + cpcap_regulators: regulators { + sw5: SW5 { + regulator-min-microvolt = <5050000>; + regulator-max-microvolt = <5050000>; + regulator-enable-ramp-delay = <50000>; + regulator-boot-on; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/regulator/gpio-regulator.txt b/Documentation/devicetree/bindings/regulator/gpio-regulator.txt index e5cac1e0ca8a..dd1ed789728e 100644 --- a/Documentation/devicetree/bindings/regulator/gpio-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/gpio-regulator.txt @@ -13,7 +13,7 @@ Optional properties: - startup-delay-us : Startup time in microseconds. - enable-active-high : Polarity of GPIO is active high (default is low). - regulator-type : Specifies what is being regulated, must be either - "voltage" or "current", defaults to current. + "voltage" or "current", defaults to voltage. Any property defined as part of the core regulator binding defined in regulator.txt can also be used. diff --git a/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt index 1f8d6f84b657..4e3dfb5b5f16 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt @@ -22,6 +22,7 @@ Regulator nodes are identified by their compatible: "qcom,rpm-pm8841-regulators" "qcom,rpm-pm8916-regulators" "qcom,rpm-pm8941-regulators" + "qcom,rpm-pm8994-regulators" "qcom,rpm-pma8084-regulators" - vdd_s1-supply: @@ -80,6 +81,56 @@ Regulator nodes are identified by their compatible: - vdd_s10-supply: - vdd_s11-supply: - vdd_s12-supply: +- vdd_l1-supply: +- vdd_l2_l26_l28-supply: +- vdd_l3_l11-supply: +- vdd_l4_l27_l31-supply: +- vdd_l5_l7-supply: +- vdd_l6_l12_l32-supply: +- vdd_l5_l7-supply: +- vdd_l8_l16_l30-supply: +- vdd_l9_l10_l18_l22-supply: +- vdd_l9_l10_l18_l22-supply: +- vdd_l3_l11-supply: +- vdd_l6_l12_l32-supply: +- vdd_l13_l19_l23_l24-supply: +- vdd_l14_l15-supply: +- vdd_l14_l15-supply: +- vdd_l8_l16_l30-supply: +- vdd_l17_l29-supply: +- vdd_l9_l10_l18_l22-supply: +- vdd_l13_l19_l23_l24-supply: +- vdd_l20_l21-supply: +- vdd_l20_l21-supply: +- vdd_l9_l10_l18_l22-supply: +- vdd_l13_l19_l23_l24-supply: +- vdd_l13_l19_l23_l24-supply: +- vdd_l25-supply: +- vdd_l2_l26_l28-supply: +- vdd_l4_l27_l31-supply: +- vdd_l2_l26_l28-supply: +- vdd_l17_l29-supply: +- vdd_l8_l16_l30-supply: +- vdd_l4_l27_l31-supply: +- vdd_l6_l12_l32-supply: +- vdd_lvs1_2-supply: + Usage: optional (pm8994 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_s4-supply: +- vdd_s5-supply: +- vdd_s6-supply: +- vdd_s7-supply: +- vdd_s8-supply: +- vdd_s9-supply: +- vdd_s10-supply: +- vdd_s11-supply: +- vdd_s12-supply: - vdd_l1_l11-supply: - vdd_l2_l3_l4_l27-supply: - vdd_l5_l7-supply: @@ -113,6 +164,11 @@ pm8941: l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3, 5vs1, 5vs2 +pm8994: + s1, s2, s3, s4, s5, s6, s7, s8, s9, s10, s11, s12, l1, l2, l3, l4, l5, + l6, l7, l8, l9, l10, l11, l12, l13, l14, l15, l16, l17, l18, l19, l20, + l21, l22, l23, l24, l25, l26, l27, l28, l29, l30, l31, l32, lvs1, lvs2 + pma8084: s1, s2, s3, s4, s5, s6, s7, s8, s9, s10, s11, s12, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14, l15, l16, l17, l18, l19, l20, diff --git a/Documentation/devicetree/bindings/spi/spi-lantiq-ssc.txt b/Documentation/devicetree/bindings/spi/spi-lantiq-ssc.txt new file mode 100644 index 000000000000..6069b95a883d --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-lantiq-ssc.txt @@ -0,0 +1,29 @@ +Lantiq Synchronous Serial Controller (SSC) SPI master driver + +Required properties: +- compatible: "lantiq,ase-spi", "lantiq,falcon-spi", "lantiq,xrx100-spi" +- #address-cells: see spi-bus.txt +- #size-cells: see spi-bus.txt +- reg: address and length of the spi master registers +- interrupts: should contain the "spi_rx", "spi_tx" and "spi_err" interrupt. + + +Optional properties: +- clocks: spi clock phandle +- num-cs: see spi-bus.txt, set to 8 if unset +- base-cs: the number of the first chip select, set to 1 if unset. + +Example: + + +spi: spi@E100800 { + compatible = "lantiq,xrx200-spi", "lantiq,xrx100-spi"; + reg = <0xE100800 0x100>; + interrupt-parent = <&icu0>; + interrupts = <22 23 24>; + interrupt-names = "spi_rx", "spi_tx", "spi_err"; + #address-cells = <1>; + #size-cells = <1>; + num-cs = <6>; + base-cs = <1>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-rockchip.txt b/Documentation/devicetree/bindings/spi/spi-rockchip.txt index d2ca153614f9..83da4931d832 100644 --- a/Documentation/devicetree/bindings/spi/spi-rockchip.txt +++ b/Documentation/devicetree/bindings/spi/spi-rockchip.txt @@ -31,6 +31,10 @@ Optional Properties: - rx-sample-delay-ns: nanoseconds to delay after the SCLK edge before sampling Rx data (may need to be fine tuned for high capacitance lines). No delay (0) by default. +- pinctrl-names: Names for the pin configuration(s); may be "default" or + "sleep", where the "sleep" configuration may describe the state + the pins should be in during system suspend. See also + pinctrl/pinctrl-bindings.txt. Example: @@ -46,4 +50,7 @@ Example: interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>; clock-names = "spiclk", "apb_pclk"; + pinctrl-0 = <&spi1_pins>; + pinctrl-1 = <&spi1_sleep>; + pinctrl-names = "default", "sleep"; }; diff --git a/Documentation/devicetree/bindings/timer/cortina,gemini-timer.txt b/Documentation/devicetree/bindings/timer/cortina,gemini-timer.txt new file mode 100644 index 000000000000..16ea1d3b2e9e --- /dev/null +++ b/Documentation/devicetree/bindings/timer/cortina,gemini-timer.txt @@ -0,0 +1,22 @@ +Cortina Systems Gemini timer + +This timer is embedded in the Cortina Systems Gemini SoCs. + +Required properties: + +- compatible : Must be "cortina,gemini-timer" +- reg : Should contain registers location and length +- interrupts : Should contain the three timer interrupts with + flags for rising edge +- syscon : a phandle to the global Gemini system controller + +Example: + +timer@43000000 { + compatible = "cortina,gemini-timer"; + reg = <0x43000000 0x1000>; + interrupts = <14 IRQ_TYPE_EDGE_RISING>, /* Timer 1 */ + <15 IRQ_TYPE_EDGE_RISING>, /* Timer 2 */ + <16 IRQ_TYPE_EDGE_RISING>; /* Timer 3 */ + syscon = <&syscon>; +}; diff --git a/Documentation/devicetree/bindings/timer/renesas,ostm.txt b/Documentation/devicetree/bindings/timer/renesas,ostm.txt new file mode 100644 index 000000000000..be3ae0fdf775 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/renesas,ostm.txt @@ -0,0 +1,30 @@ +* Renesas OS Timer (OSTM) + +The OSTM is a multi-channel 32-bit timer/counter with fixed clock +source that can operate in either interval count down timer or free-running +compare match mode. + +Channels are independent from each other. + +Required Properties: + + - compatible: must be one or more of the following: + - "renesas,r7s72100-ostm" for the r7s72100 OSTM + - "renesas,ostm" for any OSTM + This is a fallback for the above renesas,*-ostm entries + + - reg: base address and length of the register block for a timer channel. + + - interrupts: interrupt specifier for the timer channel. + + - clocks: clock specifier for the timer channel. + +Example: R7S72100 (RZ/A1H) OSTM node + + ostm0: timer@fcfec000 { + compatible = "renesas,r7s72100-ostm", "renesas,ostm"; + reg = <0xfcfec000 0x30>; + interrupts = <GIC_SPI 102 IRQ_TYPE_EDGE_RISING>; + clocks = <&mstp5_clks R7S72100_CLK_OSTM0>; + power-domains = <&cpg_clocks>; + }; |