diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
445 files changed, 10554 insertions, 865 deletions
diff --git a/Documentation/devicetree/bindings/arm/amlogic,scpi.txt b/Documentation/devicetree/bindings/arm/amlogic,scpi.txt new file mode 100644 index 000000000000..7b9a861e9306 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/amlogic,scpi.txt @@ -0,0 +1,20 @@ +System Control and Power Interface (SCPI) Message Protocol +(in addition to the standard binding in [0]) +---------------------------------------------------------- +Required properties + +- compatible : should be "amlogic,meson-gxbb-scpi" + +AMLOGIC SRAM and Shared Memory for SCPI +------------------------------------ + +Required properties: +- compatible : should be "amlogic,meson-gxbb-sram" + +Each sub-node represents the reserved area for SCPI. + +Required sub-node properties: +- compatible : should be "amlogic,meson-gxbb-scp-shmem" for SRAM based shared + memory on Amlogic GXBB SoC. + +[0] Documentation/devicetree/bindings/arm/arm,scpi.txt diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt index fcc6f6c10803..c246cd2730d9 100644 --- a/Documentation/devicetree/bindings/arm/amlogic.txt +++ b/Documentation/devicetree/bindings/arm/amlogic.txt @@ -17,6 +17,18 @@ Boards with the Amlogic Meson GXBaby SoC shall have the following properties: Required root node property: compatible: "amlogic,meson-gxbb"; +Boards with the Amlogic Meson GXL S905X SoC shall have the following properties: + Required root node property: + compatible: "amlogic,s905x", "amlogic,meson-gxl"; + +Boards with the Amlogic Meson GXL S905D SoC shall have the following properties: + Required root node property: + compatible: "amlogic,s905d", "amlogic,meson-gxl"; + +Boards with the Amlogic Meson GXM S912 SoC shall have the following properties: + Required root node property: + compatible: "amlogic,s912", "amlogic,meson-gxm"; + Board compatible values: - "geniatech,atv1200" (Meson6) - "minix,neo-x8" (Meson8) @@ -28,3 +40,12 @@ Board compatible values: - "hardkernel,odroid-c2" (Meson gxbb) - "amlogic,p200" (Meson gxbb) - "amlogic,p201" (Meson gxbb) + - "wetek,hub" (Meson gxbb) + - "wetek,play2" (Meson gxbb) + - "amlogic,p212" (Meson gxl s905x) + - "amlogic,p230" (Meson gxl s905d) + - "amlogic,p231" (Meson gxl s905d) + - "amlogic,q200" (Meson gxm s912) + - "amlogic,q201" (Meson gxm s912) + - "nexbox,a95x" (Meson gxbb or Meson gxl s905x) + - "nexbox,a1" (Meson gxm s912) diff --git a/Documentation/devicetree/bindings/arm/arch_timer.txt b/Documentation/devicetree/bindings/arm/arch_timer.txt index ef5fbe9a77c7..e926aea1147d 100644 --- a/Documentation/devicetree/bindings/arm/arch_timer.txt +++ b/Documentation/devicetree/bindings/arm/arch_timer.txt @@ -31,6 +31,12 @@ to deliver its interrupts via SPIs. This also affects writes to the tval register, due to the implicit counter read. +- hisilicon,erratum-161010101 : A boolean property. Indicates the + presence of Hisilicon erratum 161010101, which says that reading the + counters is unreliable in some cases, and reads may return a value 32 + beyond the correct value. This also affects writes to the tval + registers, due to the implicit counter read. + ** Optional properties: - arm,cpu-registers-not-fw-configured : Firmware does not initialize @@ -38,6 +44,11 @@ to deliver its interrupts via SPIs. architecturally-defined reset values. Only supported for 32-bit systems which follow the ARMv7 architected reset values. +- arm,no-tick-in-suspend : The main counter does not tick when the system is in + low-power system suspend on some SoCs. This behavior does not match the + Architecture Reference Manual's specification that the system counter "must + be implemented in an always-on power domain." + Example: diff --git a/Documentation/devicetree/bindings/arm/arm,scpi.txt b/Documentation/devicetree/bindings/arm/arm,scpi.txt index faa4b44572e3..401831973638 100644 --- a/Documentation/devicetree/bindings/arm/arm,scpi.txt +++ b/Documentation/devicetree/bindings/arm/arm,scpi.txt @@ -7,7 +7,10 @@ by Linux to initiate various system control and power operations. Required properties: -- compatible : should be "arm,scpi" +- compatible : should be + * "arm,scpi" : For implementations complying to SCPI v1.0 or above + * "arm,scpi-pre-1.0" : For implementations complying to all + unversioned releases prior to SCPI v1.0 - mboxes: List of phandle and mailbox channel specifiers All the channels reserved by remote SCP firmware for use by SCPI message protocol should be specified in any order @@ -59,18 +62,14 @@ SRAM and Shared Memory for SCPI A small area of SRAM is reserved for SCPI communication between application processors and SCP. -Required properties: -- compatible : should be "arm,juno-sram-ns" for Non-secure SRAM on Juno - -The rest of the properties should follow the generic mmio-sram description -found in ../../sram/sram.txt +The properties should follow the generic mmio-sram description found in [3] Each sub-node represents the reserved area for SCPI. Required sub-node properties: - reg : The base offset and size of the reserved area with the SRAM -- compatible : should be "arm,juno-scp-shmem" for Non-secure SRAM based - shared memory on Juno platforms +- compatible : should be "arm,scp-shmem" for Non-secure SRAM based + shared memory Sensor bindings for the sensors based on SCPI Message Protocol -------------------------------------------------------------- @@ -81,11 +80,9 @@ Required properties: - #thermal-sensor-cells: should be set to 1. This property follows the thermal device tree bindings[2]. - Valid cell values are raw identifiers (Sensor - ID) as used by the firmware. Refer to - platform documentation for your - implementation for the IDs to use. For Juno - R0 and Juno R1 refer to [3]. + Valid cell values are raw identifiers (Sensor ID) + as used by the firmware. Refer to platform details + for your implementation for the IDs to use. Power domain bindings for the power domains based on SCPI Message Protocol ------------------------------------------------------------ @@ -112,7 +109,7 @@ Required properties: [0] http://infocenter.arm.com/help/topic/com.arm.doc.dui0922b/index.html [1] Documentation/devicetree/bindings/clock/clock-bindings.txt [2] Documentation/devicetree/bindings/thermal/thermal.txt -[3] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dui0922b/apas03s22.html +[3] Documentation/devicetree/bindings/sram/sram.txt [4] Documentation/devicetree/bindings/power/power_domain.txt Example: diff --git a/Documentation/devicetree/bindings/arm/arm-boards b/Documentation/devicetree/bindings/arm/arm-boards index ab318a56fca2..b6e810c2781a 100644 --- a/Documentation/devicetree/bindings/arm/arm-boards +++ b/Documentation/devicetree/bindings/arm/arm-boards @@ -148,11 +148,12 @@ Example: /dts-v1/; #include <dt-bindings/interrupt-controller/irq.h> -#include "skeleton.dtsi" / { model = "ARM RealView PB1176 with device tree"; compatible = "arm,realview-pb1176"; + #address-cells = <1>; + #size-cells = <1>; soc { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt index e1f5ad855f14..29737b9b616e 100644 --- a/Documentation/devicetree/bindings/arm/atmel-at91.txt +++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt @@ -225,3 +225,19 @@ required properties: compatible = "atmel,sama5d3-sfr", "syscon"; reg = <0xf0038000 0x60>; }; + +Security Module (SECUMOD) + +The Security Module macrocell provides all necessary secure functions to avoid +voltage, temperature, frequency and mechanical attacks on the chip. It also +embeds secure memories that can be scrambled + +required properties: +- compatible: Should be "atmel,<chip>-secumod", "syscon". + <chip> can be "sama5d2". +- reg: Should contain registers location and length + + secumod@fc040000 { + compatible = "atmel,sama5d2-secumod", "syscon"; + reg = <0xfc040000 0x100>; + }; diff --git a/Documentation/devicetree/bindings/arm/axentia.txt b/Documentation/devicetree/bindings/arm/axentia.txt new file mode 100644 index 000000000000..ea3fb96ae465 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/axentia.txt @@ -0,0 +1,19 @@ +Device tree bindings for Axentia ARM devices +============================================ + +Linea CPU module +---------------- + +Required root node properties: +compatible = "axentia,linea", + "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5"; +and following the rules from atmel-at91.txt for a sama5d31 SoC. + + +TSE-850 v3 board +---------------- + +Required root node properties: +compatible = "axentia,tse850v3", "axentia,linea", + "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5"; +and following the rules from above for the axentia,linea CPU module. diff --git a/Documentation/devicetree/bindings/arm/bcm/ns2.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,ns2.txt index 35f056f4a1c3..35f056f4a1c3 100644 --- a/Documentation/devicetree/bindings/arm/bcm/ns2.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,ns2.txt diff --git a/Documentation/devicetree/bindings/arm/cpu-capacity.txt b/Documentation/devicetree/bindings/arm/cpu-capacity.txt new file mode 100644 index 000000000000..7809fbe0cdb7 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/cpu-capacity.txt @@ -0,0 +1,236 @@ +========================================== +ARM CPUs capacity bindings +========================================== + +========================================== +1 - Introduction +========================================== + +ARM systems may be configured to have cpus with different power/performance +characteristics within the same chip. In this case, additional information has +to be made available to the kernel for it to be aware of such differences and +take decisions accordingly. + +========================================== +2 - CPU capacity definition +========================================== + +CPU capacity is a number that provides the scheduler information about CPUs +heterogeneity. Such heterogeneity can come from micro-architectural differences +(e.g., ARM big.LITTLE systems) or maximum frequency at which CPUs can run +(e.g., SMP systems with multiple frequency domains). Heterogeneity in this +context is about differing performance characteristics; this binding tries to +capture a first-order approximation of the relative performance of CPUs. + +CPU capacities are obtained by running a suitable benchmark. This binding makes +no guarantees on the validity or suitability of any particular benchmark, the +final capacity should, however, be: + +* A "single-threaded" or CPU affine benchmark +* Divided by the running frequency of the CPU executing the benchmark +* Not subject to dynamic frequency scaling of the CPU + +For the time being we however advise usage of the Dhrystone benchmark. What +above thus becomes: + +CPU capacities are obtained by running the Dhrystone benchmark on each CPU at +max frequency (with caches enabled). The obtained DMIPS score is then divided +by the frequency (in MHz) at which the benchmark has been run, so that +DMIPS/MHz are obtained. Such values are then normalized w.r.t. the highest +score obtained in the system. + +========================================== +3 - capacity-dmips-mhz +========================================== + +capacity-dmips-mhz is an optional cpu node [1] property: u32 value +representing CPU capacity expressed in normalized DMIPS/MHz. At boot time, the +maximum frequency available to the cpu is then used to calculate the capacity +value internally used by the kernel. + +capacity-dmips-mhz property is all-or-nothing: if it is specified for a cpu +node, it has to be specified for every other cpu nodes, or the system will +fall back to the default capacity value for every CPU. If cpufreq is not +available, final capacities are calculated by directly using capacity-dmips- +mhz values (normalized w.r.t. the highest value found while parsing the DT). + +=========================================== +4 - Examples +=========================================== + +Example 1 (ARM 64-bit, 6-cpu system, two clusters): +capacities-dmips-mhz are scaled w.r.t. 1024 (cpu@0 and cpu@1) +supposing cluster0@max-freq=1100 and custer1@max-freq=850, +final capacities are 1024 for cluster0 and 446 for cluster1 + +cpus { + #address-cells = <2>; + #size-cells = <0>; + + cpu-map { + cluster0 { + core0 { + cpu = <&A57_0>; + }; + core1 { + cpu = <&A57_1>; + }; + }; + + cluster1 { + core0 { + cpu = <&A53_0>; + }; + core1 { + cpu = <&A53_1>; + }; + core2 { + cpu = <&A53_2>; + }; + core3 { + cpu = <&A53_3>; + }; + }; + }; + + idle-states { + entry-method = "arm,psci"; + + CPU_SLEEP_0: cpu-sleep-0 { + compatible = "arm,idle-state"; + arm,psci-suspend-param = <0x0010000>; + local-timer-stop; + entry-latency-us = <100>; + exit-latency-us = <250>; + min-residency-us = <150>; + }; + + CLUSTER_SLEEP_0: cluster-sleep-0 { + compatible = "arm,idle-state"; + arm,psci-suspend-param = <0x1010000>; + local-timer-stop; + entry-latency-us = <800>; + exit-latency-us = <700>; + min-residency-us = <2500>; + }; + }; + + A57_0: cpu@0 { + compatible = "arm,cortex-a57","arm,armv8"; + reg = <0x0 0x0>; + device_type = "cpu"; + enable-method = "psci"; + next-level-cache = <&A57_L2>; + clocks = <&scpi_dvfs 0>; + cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; + capacity-dmips-mhz = <1024>; + }; + + A57_1: cpu@1 { + compatible = "arm,cortex-a57","arm,armv8"; + reg = <0x0 0x1>; + device_type = "cpu"; + enable-method = "psci"; + next-level-cache = <&A57_L2>; + clocks = <&scpi_dvfs 0>; + cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; + capacity-dmips-mhz = <1024>; + }; + + A53_0: cpu@100 { + compatible = "arm,cortex-a53","arm,armv8"; + reg = <0x0 0x100>; + device_type = "cpu"; + enable-method = "psci"; + next-level-cache = <&A53_L2>; + clocks = <&scpi_dvfs 1>; + cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; + capacity-dmips-mhz = <578>; + }; + + A53_1: cpu@101 { + compatible = "arm,cortex-a53","arm,armv8"; + reg = <0x0 0x101>; + device_type = "cpu"; + enable-method = "psci"; + next-level-cache = <&A53_L2>; + clocks = <&scpi_dvfs 1>; + cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; + capacity-dmips-mhz = <578>; + }; + + A53_2: cpu@102 { + compatible = "arm,cortex-a53","arm,armv8"; + reg = <0x0 0x102>; + device_type = "cpu"; + enable-method = "psci"; + next-level-cache = <&A53_L2>; + clocks = <&scpi_dvfs 1>; + cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; + capacity-dmips-mhz = <578>; + }; + + A53_3: cpu@103 { + compatible = "arm,cortex-a53","arm,armv8"; + reg = <0x0 0x103>; + device_type = "cpu"; + enable-method = "psci"; + next-level-cache = <&A53_L2>; + clocks = <&scpi_dvfs 1>; + cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; + capacity-dmips-mhz = <578>; + }; + + A57_L2: l2-cache0 { + compatible = "cache"; + }; + + A53_L2: l2-cache1 { + compatible = "cache"; + }; +}; + +Example 2 (ARM 32-bit, 4-cpu system, two clusters, + cpus 0,1@1GHz, cpus 2,3@500MHz): +capacities-dmips-mhz are scaled w.r.t. 2 (cpu@0 and cpu@1), this means that first +cpu@0 and cpu@1 are twice fast than cpu@2 and cpu@3 (at the same frequency) + +cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0>; + capacity-dmips-mhz = <2>; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <1>; + capacity-dmips-mhz = <2>; + }; + + cpu2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x100>; + capacity-dmips-mhz = <1>; + }; + + cpu3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x101>; + capacity-dmips-mhz = <1>; + }; +}; + +=========================================== +5 - References +=========================================== + +[1] ARM Linux Kernel documentation - CPUs bindings + Documentation/devicetree/bindings/arm/cpus.txt diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index e6782d50cbcd..698ad1f097fa 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -158,6 +158,7 @@ nodes to be present and contain the properties described below. "arm,cortex-a53" "arm,cortex-a57" "arm,cortex-a72" + "arm,cortex-a73" "arm,cortex-m0" "arm,cortex-m0+" "arm,cortex-m1" @@ -178,6 +179,7 @@ nodes to be present and contain the properties described below. "marvell,pj4b" "marvell,sheeva-v5" "nvidia,tegra132-denver" + "nvidia,tegra186-denver" "qcom,krait" "qcom,kryo" "qcom,scorpion" @@ -201,6 +203,7 @@ nodes to be present and contain the properties described below. "marvell,armada-380-smp" "marvell,armada-390-smp" "marvell,armada-xp-smp" + "marvell,98dx3236-smp" "mediatek,mt6589-smp" "mediatek,mt81xx-tz-smp" "qcom,gcc-msm8660" @@ -241,6 +244,14 @@ nodes to be present and contain the properties described below. # List of phandles to idle state nodes supported by this cpu [3]. + - capacity-dmips-mhz + Usage: Optional + Value type: <u32> + Definition: + # u32 value representing CPU capacity [3] in + DMIPS/MHz, relative to highest capacity-dmips-mhz + in the system. + - rockchip,pmu Usage: optional for systems that have an "enable-method" property value of "rockchip,rk3066-smp" @@ -464,3 +475,5 @@ cpus { [2] arm/msm/qcom,kpss-acc.txt [3] ARM Linux kernel documentation - idle states bindings Documentation/devicetree/bindings/arm/idle-states.txt +[3] ARM Linux kernel documentation - cpu capacity bindings + Documentation/devicetree/bindings/arm/cpu-capacity.txt diff --git a/Documentation/devicetree/bindings/arm/davinci.txt b/Documentation/devicetree/bindings/arm/davinci.txt index f0841ce725b5..715622c36260 100644 --- a/Documentation/devicetree/bindings/arm/davinci.txt +++ b/Documentation/devicetree/bindings/arm/davinci.txt @@ -13,6 +13,10 @@ EnBW AM1808 based CMC board Required root node properties: - compatible = "enbw,cmc", "ti,da850; +LEGO MINDSTORMS EV3 (AM1808 based) +Required root node properties: + - compatible = "lego,ev3", "ti,da850"; + Generic DaVinci Boards ---------------------- diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt index dbbc0952021c..c9c567ae227f 100644 --- a/Documentation/devicetree/bindings/arm/fsl.txt +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -97,7 +97,7 @@ Freescale LS1021A Platform Device Tree Bindings Required root node compatible properties: - compatible = "fsl,ls1021a"; -Freescale LS1021A SoC-specific Device Tree Bindings +Freescale SoC-specific Device Tree Bindings ------------------------------------------- Freescale SCFG @@ -105,7 +105,11 @@ Freescale SCFG configuration and status registers for the chip. Such as getting PEX port status. Required properties: - - compatible: should be "fsl,ls1021a-scfg" + - compatible: Should contain a chip-specific compatible string, + Chip-specific strings are of the form "fsl,<chip>-scfg", + The following <chip>s are known to be supported: + ls1012a, ls1021a, ls1043a, ls1046a, ls2080a. + - reg: should contain base address and length of SCFG memory-mapped registers Example: @@ -119,7 +123,11 @@ Freescale DCFG configuration and status for the device. Such as setting the secondary core start address and release the secondary core from holdoff and startup. Required properties: - - compatible: should be "fsl,ls1021a-dcfg" + - compatible: Should contain a chip-specific compatible string, + Chip-specific strings are of the form "fsl,<chip>-dcfg", + The following <chip>s are known to be supported: + ls1012a, ls1021a, ls1043a, ls1046a, ls2080a. + - reg : should contain base address and length of DCFG memory-mapped registers Example: @@ -131,6 +139,26 @@ Example: Freescale ARMv8 based Layerscape SoC family Device Tree Bindings ---------------------------------------------------------------- +LS1012A SoC +Required root node properties: + - compatible = "fsl,ls1012a"; + +LS1012A ARMv8 based RDB Board +Required root node properties: + - compatible = "fsl,ls1012a-rdb", "fsl,ls1012a"; + +LS1012A ARMv8 based FRDM Board +Required root node properties: + - compatible = "fsl,ls1012a-frdm", "fsl,ls1012a"; + +LS1012A ARMv8 based QDS Board +Required root node properties: + - compatible = "fsl,ls1012a-qds", "fsl,ls1012a"; + +LS1043A SoC +Required root node properties: + - compatible = "fsl,ls1043a"; + LS1043A ARMv8 based RDB Board Required root node properties: - compatible = "fsl,ls1043a-rdb", "fsl,ls1043a"; @@ -139,6 +167,22 @@ LS1043A ARMv8 based QDS Board Required root node properties: - compatible = "fsl,ls1043a-qds", "fsl,ls1043a"; +LS1046A SoC +Required root node properties: + - compatible = "fsl,ls1046a"; + +LS1046A ARMv8 based QDS Board +Required root node properties: + - compatible = "fsl,ls1046a-qds", "fsl,ls1046a"; + +LS1046A ARMv8 based RDB Board +Required root node properties: + - compatible = "fsl,ls1046a-rdb", "fsl,ls1046a"; + +LS2080A SoC +Required root node properties: + - compatible = "fsl,ls2080a"; + LS2080A ARMv8 based Simulator model Required root node properties: - compatible = "fsl,ls2080a-simu", "fsl,ls2080a"; diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt index 3f81575aa6be..f1c1e21a8110 100644 --- a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt +++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt @@ -1,5 +1,9 @@ Hisilicon Platforms Device Tree Bindings ---------------------------------------------------- +Hi3660 SoC +Required root node properties: + - compatible = "hisilicon,hi3660"; + Hi4511 Board Required root node properties: - compatible = "hisilicon,hi3620-hi4511"; @@ -28,6 +32,10 @@ HiP06 D03 Board Required root node properties: - compatible = "hisilicon,hip06-d03"; +HiP07 D05 Board +Required root node properties: + - compatible = "hisilicon,hip07-d05"; + Hisilicon system controller Required properties: diff --git a/Documentation/devicetree/bindings/arm/juno,scpi.txt b/Documentation/devicetree/bindings/arm/juno,scpi.txt new file mode 100644 index 000000000000..2ace8696bbee --- /dev/null +++ b/Documentation/devicetree/bindings/arm/juno,scpi.txt @@ -0,0 +1,26 @@ +System Control and Power Interface (SCPI) Message Protocol +(in addition to the standard binding in [0]) + +Juno SRAM and Shared Memory for SCPI +------------------------------------ + +Required properties: +- compatible : should be "arm,juno-sram-ns" for Non-secure SRAM + +Each sub-node represents the reserved area for SCPI. + +Required sub-node properties: +- reg : The base offset and size of the reserved area with the SRAM +- compatible : should be "arm,juno-scp-shmem" for Non-secure SRAM based + shared memory on Juno platforms + +Sensor bindings for the sensors based on SCPI Message Protocol +-------------------------------------------------------------- +Required properties: +- compatible : should be "arm,scpi-sensors". +- #thermal-sensor-cells: should be set to 1. + For Juno R0 and Juno R1 refer to [1] for the + sensor identifiers + +[0] Documentation/devicetree/bindings/arm/arm,scpi.txt +[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dui0922b/apas03s22.html diff --git a/Documentation/devicetree/bindings/arm/keystone/ti,sci.txt b/Documentation/devicetree/bindings/arm/keystone/ti,sci.txt new file mode 100644 index 000000000000..31f5f9a104cc --- /dev/null +++ b/Documentation/devicetree/bindings/arm/keystone/ti,sci.txt @@ -0,0 +1,81 @@ +Texas Instruments System Control Interface (TI-SCI) Message Protocol +-------------------------------------------------------------------- + +Texas Instrument's processors including those belonging to Keystone generation +of processors have separate hardware entity which is now responsible for the +management of the System on Chip (SoC) system. These include various system +level functions as well. + +An example of such an SoC is K2G, which contains the system control hardware +block called Power Management Micro Controller (PMMC). This hardware block is +initialized early into boot process and provides services to Operating Systems +on multiple processors including ones running Linux. + +See http://processors.wiki.ti.com/index.php/TISCI for protocol definition. + +TI-SCI controller Device Node: +============================= + +The TI-SCI node describes the Texas Instrument's System Controller entity node. +This parent node may optionally have additional children nodes which describe +specific functionality such as clocks, power domain, reset or additional +functionality as may be required for the SoC. This hierarchy also describes the +relationship between the TI-SCI parent node to the child node. + +Required properties: +------------------- +- compatible: should be "ti,k2g-sci" +- mbox-names: + "rx" - Mailbox corresponding to receive path + "tx" - Mailbox corresponding to transmit path + +- mboxes: Mailboxes corresponding to the mbox-names. Each value of the mboxes + property should contain a phandle to the mailbox controller device + node and an args specifier that will be the phandle to the intended + sub-mailbox child node to be used for communication. + +See Documentation/devicetree/bindings/mailbox/mailbox.txt for more details +about the generic mailbox controller and client driver bindings. Also see +Documentation/devicetree/bindings/mailbox/ti,message-manager.txt for typical +controller that is used to communicate with this System controllers. + +Optional Properties: +------------------- +- reg-names: + debug_messages - Map the Debug message region +- reg: register space corresponding to the debug_messages +- ti,system-reboot-controller: If system reboot can be triggered by SoC reboot + +Example (K2G): +------------- + pmmc: pmmc { + compatible = "ti,k2g-sci"; + mbox-names = "rx", "tx"; + mboxes= <&msgmgr &msgmgr_proxy_pmmc_rx>, + <&msgmgr &msgmgr_proxy_pmmc_tx>; + reg-names = "debug_messages"; + reg = <0x02921800 0x800>; + }; + + +TI-SCI Client Device Node: +========================= + +Client nodes are maintained as children of the relevant TI-SCI device node. + +Example (K2G): +------------- + pmmc: pmmc { + compatible = "ti,k2g-sci"; + ... + + my_clk_node: clk_node { + ... + ... + }; + + my_pd_node: pd_node { + ... + ... + }; + }; diff --git a/Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt b/Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt new file mode 100644 index 000000000000..26eb9d3aa630 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt @@ -0,0 +1,16 @@ +Resume Control +-------------- +Available on Marvell SOCs: 98DX3336 and 98DX4251 + +Required properties: + +- compatible: must be "marvell,98dx3336-resume-ctrl" + +- reg: Should contain resume control registers location and length + +Example: + +resume@20980 { + compatible = "marvell,98dx3336-resume-ctrl"; + reg = <0x20980 0x10>; +}; diff --git a/Documentation/devicetree/bindings/arm/marvell/98dx3236.txt b/Documentation/devicetree/bindings/arm/marvell/98dx3236.txt new file mode 100644 index 000000000000..64e8c73fc5ab --- /dev/null +++ b/Documentation/devicetree/bindings/arm/marvell/98dx3236.txt @@ -0,0 +1,23 @@ +Marvell 98DX3236, 98DX3336 and 98DX4251 Platforms Device Tree Bindings +---------------------------------------------------------------------- + +Boards with a SoC of the Marvell 98DX3236, 98DX3336 and 98DX4251 families +shall have the following property: + +Required root node property: + +compatible: must contain "marvell,armadaxp-98dx3236" + +In addition, boards using the Marvell 98DX3336 SoC shall have the +following property: + +Required root node property: + +compatible: must contain "marvell,armadaxp-98dx3336" + +In addition, boards using the Marvell 98DX4251 SoC shall have the +following property: + +Required root node property: + +compatible: must contain "marvell,armadaxp-98dx4251" diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index f53e2ee65e35..8219b2c6bb29 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -86,6 +86,9 @@ SoCs: - DRA722 compatible = "ti,dra722", "ti,dra72", "ti,dra7" +- DRA718 + compatible = "ti,dra718", "ti,dra722", "ti,dra72", "ti,dra7" + - AM5728 compatible = "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7" @@ -148,6 +151,9 @@ Boards: - AM335X SBC-T335 : single board computer, built around the Sitara AM3352/4 compatible = "compulab,sbc-t335", "compulab,cm-t335", "ti,am33xx" +- AM335X phyCORE-AM335x: Development kit + compatible = "phytec,am335x-pcm-953", "phytec,am335x-phycore-som", "ti,am33xx" + - OMAP5 EVM : Evaluation Module compatible = "ti,omap5-evm", "ti,omap5" @@ -175,12 +181,18 @@ Boards: - AM5728 IDK compatible = "ti,am5728-idk", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7" +- AM5718 IDK + compatible = "ti,am5718-idk", "ti,am5718", "ti,dra7" + - DRA742 EVM: Software Development Board for DRA742 compatible = "ti,dra7-evm", "ti,dra742", "ti,dra74", "ti,dra7" - DRA722 EVM: Software Development Board for DRA722 compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7" +- DRA718 EVM: Software Development Board for DRA718 + compatible = "ti,dra718-evm", "ti,dra718", "ti,dra722", "ti,dra72", "ti,dra7" + - DM3730 Logic PD Torpedo + Wireless: Commercial System on Module with WiFi and Bluetooth compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3630", "ti,omap3" diff --git a/Documentation/devicetree/bindings/arm/oxnas.txt b/Documentation/devicetree/bindings/arm/oxnas.txt index b9e49711ba05..ac64e60f99f1 100644 --- a/Documentation/devicetree/bindings/arm/oxnas.txt +++ b/Documentation/devicetree/bindings/arm/oxnas.txt @@ -5,5 +5,10 @@ Boards with the OX810SE SoC shall have the following properties: Required root node property: compatible: "oxsemi,ox810se" +Boards with the OX820 SoC shall have the following properties: + Required root node property: + compatible: "oxsemi,ox820" + Board compatible values: - "wd,mbwe" (OX810SE) + - "cloudengines,pogoplugv3" (OX820) diff --git a/Documentation/devicetree/bindings/arm/qcom.txt b/Documentation/devicetree/bindings/arm/qcom.txt index 3e24518c6678..028d16e72186 100644 --- a/Documentation/devicetree/bindings/arm/qcom.txt +++ b/Documentation/devicetree/bindings/arm/qcom.txt @@ -21,7 +21,10 @@ The 'SoC' element must be one of the following strings: apq8096 msm8916 msm8974 + msm8992 + msm8994 msm8996 + mdm9615 The 'board' element must be one of the following strings: diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index 55f388f954de..cc4ace6397ab 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -25,6 +25,10 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "radxa,rock2-square", "rockchip,rk3288"; +- Rikomagic MK808 v1 board: + Required root node properties: + - compatible = "rikomagic,mk808", "rockchip,rk3066a"; + - Firefly Firefly-RK3288 board: Required root node properties: - compatible = "firefly,firefly-rk3288", "rockchip,rk3288"; @@ -99,6 +103,18 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "mqmaker,miqi", "rockchip,rk3288"; +- Rockchip PX3 Evaluation board: + Required root node properties: + - compatible = "rockchip,px3-evb", "rockchip,px3", "rockchip,rk3188"; + +- Rockchip PX5 Evaluation board: + Required root node properties: + - compatible = "rockchip,px5-evb", "rockchip,px5", "rockchip,rk3368"; + +- Rockchip RK1108 Evaluation board + Required root node properties: + - compatible = "rockchip,rk1108-evb", "rockchip,rk1108"; + - Rockchip RK3368 evb: Required root node properties: - compatible = "rockchip,rk3368-evb-act8846", "rockchip,rk3368"; diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt index 0ea7f14ef294..3c551894f621 100644 --- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt @@ -15,6 +15,8 @@ Required root node properties: - "samsung,xyref5260" - for Exynos5260-based Samsung board. - "samsung,smdk5410" - for Exynos5410-based Samsung SMDK5410 eval board. - "samsung,smdk5420" - for Exynos5420-based Samsung SMDK5420 eval board. + - "samsung,tm2" - for Exynos5433-based Samsung TM2 board. + - "samsung,tm2e" - for Exynos5433-based Samsung TM2E board. - "samsung,sd5v1" - for Exynos5440-based Samsung board. - "samsung,ssdk5440" - for Exynos5440-based Samsung board. @@ -22,6 +24,9 @@ Required root node properties: * FriendlyARM - "friendlyarm,tiny4412" - for Exynos4412-based FriendlyARM TINY4412 board. + * TOPEET + - "topeet,itop4412-elite" - for Exynos4412-based TOPEET + Elite base board. * Google - "google,pi" - for Exynos5800-based Google Peach Pi diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt index 2f0b7169f132..c9502634316d 100644 --- a/Documentation/devicetree/bindings/arm/shmobile.txt +++ b/Documentation/devicetree/bindings/arm/shmobile.txt @@ -13,6 +13,10 @@ SoCs: compatible = "renesas,r8a73a4" - R-Mobile A1 (R8A77400) compatible = "renesas,r8a7740" + - RZ/G1M (R8A77430) + compatible = "renesas,r8a7743" + - RZ/G1E (R8A77450) + compatible = "renesas,r8a7745" - R-Car M1A (R8A77781) compatible = "renesas,r8a7778" - R-Car H1 (R8A77790) @@ -35,7 +39,7 @@ SoCs: Boards: - - Alt + - Alt (RTP0RC7794SEB00010S) compatible = "renesas,alt", "renesas,r8a7794" - APE6-EVM compatible = "renesas,ape6evm", "renesas,r8a73a4" @@ -47,9 +51,9 @@ Boards: compatible = "renesas,bockw", "renesas,r8a7778" - Genmai (RTK772100BC00000BR) compatible = "renesas,genmai", "renesas,r7s72100" - - Gose + - Gose (RTP0RC7793SEB00010S) compatible = "renesas,gose", "renesas,r8a7793" - - H3ULCB (RTP0RC7795SKB00010S) + - H3ULCB (R-Car Starter Kit Premier, RTP0RC7795SKB00010S) compatible = "renesas,h3ulcb", "renesas,r8a7795"; - Henninger compatible = "renesas,henninger", "renesas,r8a7791" @@ -61,7 +65,9 @@ Boards: compatible = "renesas,kzm9g", "renesas,sh73a0" - Lager (RTP0RC7790SEB00010S) compatible = "renesas,lager", "renesas,r8a7790" - - Marzen + - M3ULCB (R-Car Starter Kit Pro, RTP0RC7796SKB00010S) + compatible = "renesas,m3ulcb", "renesas,r8a7796"; + - Marzen (R0P7779A00010S) compatible = "renesas,marzen", "renesas,r8a7779" - Porter (M2-LCDP) compatible = "renesas,porter", "renesas,r8a7791" @@ -69,9 +75,31 @@ Boards: compatible = "renesas,rskrza1", "renesas,r7s72100" - Salvator-X (RTP0RC7795SIPB0010S) compatible = "renesas,salvator-x", "renesas,r8a7795"; - - Salvator-X + - Salvator-X (RTP0RC7796SIPB0011S) compatible = "renesas,salvator-x", "renesas,r8a7796"; - SILK (RTP0RC7794LCB00011S) compatible = "renesas,silk", "renesas,r8a7794" + - SK-RZG1E (YR8A77450S000BE) + compatible = "renesas,sk-rzg1e", "renesas,r8a7745" + - SK-RZG1M (YR8A77430S000BE) + compatible = "renesas,sk-rzg1m", "renesas,r8a7743" - Wheat compatible = "renesas,wheat", "renesas,r8a7792" + + +Most Renesas ARM SoCs have a Product Register that allows to retrieve SoC +product and revision information. If present, a device node for this register +should be added. + +Required properties: + - compatible: Must be "renesas,prr". + - reg: Base address and length of the register block. + + +Examples +-------- + + prr: chipid@ff000044 { + compatible = "renesas,prr"; + reg = <0 0xff000044 0 4>; + }; diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt index 3975d0a0e4c2..d2c46449b4eb 100644 --- a/Documentation/devicetree/bindings/arm/sunxi.txt +++ b/Documentation/devicetree/bindings/arm/sunxi.txt @@ -12,6 +12,8 @@ using one of the following compatible strings: allwinner,sun8i-a23 allwinner,sun8i-a33 allwinner,sun8i-a83t + allwinner,sun8i-h2-plus allwinner,sun8i-h3 allwinner,sun9i-a80 + allwinner,sun50i-a64 nextthing,gr8 diff --git a/Documentation/devicetree/bindings/arm/swir.txt b/Documentation/devicetree/bindings/arm/swir.txt new file mode 100644 index 000000000000..042be73a95d3 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/swir.txt @@ -0,0 +1,12 @@ +Sierra Wireless Modules device tree bindings +-------------------------------------------- + +Supported Modules : + - WP8548 : Includes MDM9615 and PM8018 in a module + +Sierra Wireless modules shall have the following properties : + Required root node property + - compatible: "swir,wp8548" for the WP8548 CF3 Module + +Board compatible values: + - "swir,mangoh-green-wp8548" for the mangOH green board with the WP8548 module diff --git a/Documentation/devicetree/bindings/ata/ahci-da850.txt b/Documentation/devicetree/bindings/ata/ahci-da850.txt new file mode 100644 index 000000000000..5f8193417725 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/ahci-da850.txt @@ -0,0 +1,18 @@ +Device tree binding for the TI DA850 AHCI SATA Controller +--------------------------------------------------------- + +Required properties: + - compatible: must be "ti,da850-ahci" + - reg: physical base addresses and sizes of the two register regions + used by the controller: the register map as defined by the + AHCI 1.1 standard and the Power Down Control Register (PWRDN) + for enabling/disabling the SATA clock receiver + - interrupts: interrupt specifier (refer to the interrupt binding) + +Example: + + sata: sata@218000 { + compatible = "ti,da850-ahci"; + reg = <0x218000 0x2000>, <0x22c018 0x4>; + interrupts = <67>; + }; diff --git a/Documentation/devicetree/bindings/ata/ahci-fsl-qoriq.txt b/Documentation/devicetree/bindings/ata/ahci-fsl-qoriq.txt index 032a7606b862..fc33ca01e9ba 100644 --- a/Documentation/devicetree/bindings/ata/ahci-fsl-qoriq.txt +++ b/Documentation/devicetree/bindings/ata/ahci-fsl-qoriq.txt @@ -3,7 +3,7 @@ Binding for Freescale QorIQ AHCI SATA Controller Required properties: - reg: Physical base address and size of the controller's register area. - compatible: Compatibility string. Must be 'fsl,<chip>-ahci', where - chip could be ls1021a, ls2080a, ls1043a etc. + chip could be ls1021a, ls1043a, ls1046a, ls2080a etc. - clocks: Input clock specifier. Refer to common clock bindings. - interrupts: Interrupt specifier. Refer to interrupt binding. diff --git a/Documentation/devicetree/bindings/ata/ahci-st.txt b/Documentation/devicetree/bindings/ata/ahci-st.txt index e1d01df8e3c1..909c9935360d 100644 --- a/Documentation/devicetree/bindings/ata/ahci-st.txt +++ b/Documentation/devicetree/bindings/ata/ahci-st.txt @@ -18,21 +18,6 @@ Optional properties: Example: - /* Example for stih416 */ - sata0: sata@fe380000 { - compatible = "st,ahci"; - reg = <0xfe380000 0x1000>; - interrupts = <GIC_SPI 157 IRQ_TYPE_NONE>; - interrupt-names = "hostc"; - phys = <&phy_port0 PHY_TYPE_SATA>; - phy-names = "ahci_phy"; - resets = <&powerdown STIH416_SATA0_POWERDOWN>, - <&softreset STIH416_SATA0_SOFTRESET>; - reset-names = "pwr-dwn", "sw-rst"; - clocks = <&clk_s_a0_ls CLK_ICN_REG>; - clock-names = "ahci_clk"; - }; - /* Example for stih407 family silicon */ sata0: sata@9b20000 { compatible = "st,ahci"; diff --git a/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt b/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt new file mode 100644 index 000000000000..83b0e54f727c --- /dev/null +++ b/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt @@ -0,0 +1,132 @@ +Device tree bindings for NVIDIA Tegra Generic Memory Interface bus + +The Generic Memory Interface bus enables memory transfers between internal and +external memory. Can be used to attach various high speed devices such as +synchronous/asynchronous NOR, FPGA, UARTS and more. + +The actual devices are instantiated from the child nodes of a GMI node. + +Required properties: + - compatible : Should contain one of the following: + For Tegra20 must contain "nvidia,tegra20-gmi". + For Tegra30 must contain "nvidia,tegra30-gmi". + - reg: Should contain GMI controller registers location and length. + - clocks: Must contain an entry for each entry in clock-names. + - clock-names: Must include the following entries: "gmi" + - resets : Must contain an entry for each entry in reset-names. + - reset-names : Must include the following entries: "gmi" + - #address-cells: The number of cells used to represent physical base + addresses in the GMI address space. Should be 2. + - #size-cells: The number of cells used to represent the size of an address + range in the GMI address space. Should be 1. + - ranges: Must be set up to reflect the memory layout with three integer values + for each chip-select line in use (only one entry is supported, see below + comments): + <cs-number> <offset> <physical address of mapping> <size> + +Note that the GMI controller does not have any internal chip-select address +decoding, because of that chip-selects either need to be managed via software +or by employing external chip-select decoding logic. + +If external chip-select logic is used to support multiple devices it is assumed +that the devices use the same timing and so are probably the same type. It also +assumes that they can fit in the 256MB address range. In this case only one +child device is supported which represents the active chip-select line, see +examples for more insight. + +The chip-select number is decoded from the child nodes second address cell of +'ranges' property, if 'ranges' property is not present or empty chip-select will +then be decoded from the first cell of the 'reg' property. + +Optional child cs node properties: + + - nvidia,snor-data-width-32bit: Use 32bit data-bus, default is 16bit. + - nvidia,snor-mux-mode: Enable address/data MUX mode. + - nvidia,snor-rdy-active-before-data: Assert RDY signal one cycle before data. + If omitted it will be asserted with data. + - nvidia,snor-rdy-active-high: RDY signal is active high + - nvidia,snor-adv-active-high: ADV signal is active high + - nvidia,snor-oe-active-high: WE/OE signal is active high + - nvidia,snor-cs-active-high: CS signal is active high + + Note that there is some special handling for the timing values. + From Tegra TRM: + Programming 0 means 1 clock cycle: actual cycle = programmed cycle + 1 + + - nvidia,snor-muxed-width: Number of cycles MUX address/data asserted on the + bus. Valid values are 0-15, default is 1 + - nvidia,snor-hold-width: Number of cycles CE stays asserted after the + de-assertion of WR_N (in case of SLAVE/MASTER Request) or OE_N + (in case of MASTER Request). Valid values are 0-15, default is 1 + - nvidia,snor-adv-width: Number of cycles during which ADV stays asserted. + Valid values are 0-15, default is 1. + - nvidia,snor-ce-width: Number of cycles before CE is asserted. + Valid values are 0-15, default is 4 + - nvidia,snor-we-width: Number of cycles during which WE stays asserted. + Valid values are 0-15, default is 1 + - nvidia,snor-oe-width: Number of cycles during which OE stays asserted. + Valid values are 0-255, default is 1 + - nvidia,snor-wait-width: Number of cycles before READY is asserted. + Valid values are 0-255, default is 3 + +Example with two SJA1000 CAN controllers connected to the GMI bus. We wrap the +controllers with a simple-bus node since they are all connected to the same +chip-select (CS4), in this example external address decoding is provided: + +gmi@70090000 { + compatible = "nvidia,tegra20-gmi"; + reg = <0x70009000 0x1000>; + #address-cells = <2>; + #size-cells = <1>; + clocks = <&tegra_car TEGRA20_CLK_NOR>; + clock-names = "gmi"; + resets = <&tegra_car 42>; + reset-names = "gmi"; + ranges = <4 0 0xd0000000 0xfffffff>; + + status = "okay"; + + bus@4,0 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 4 0 0x40100>; + + nvidia,snor-mux-mode; + nvidia,snor-adv-active-high; + + can@0 { + reg = <0 0x100>; + ... + }; + + can@40000 { + reg = <0x40000 0x100>; + ... + }; + }; +}; + +Example with one SJA1000 CAN controller connected to the GMI bus +on CS4: + +gmi@70090000 { + compatible = "nvidia,tegra20-gmi"; + reg = <0x70009000 0x1000>; + #address-cells = <2>; + #size-cells = <1>; + clocks = <&tegra_car TEGRA20_CLK_NOR>; + clock-names = "gmi"; + resets = <&tegra_car 42>; + reset-names = "gmi"; + ranges = <4 0 0xd0000000 0xfffffff>; + + status = "okay"; + + can@4,0 { + reg = <4 0 0x100>; + nvidia,snor-mux-mode; + nvidia,snor-adv-active-high; + ... + }; +}; diff --git a/Documentation/devicetree/bindings/bus/qcom,ebi2.txt b/Documentation/devicetree/bindings/bus/qcom,ebi2.txt index 920681f552db..5a7d567f6833 100644 --- a/Documentation/devicetree/bindings/bus/qcom,ebi2.txt +++ b/Documentation/devicetree/bindings/bus/qcom,ebi2.txt @@ -51,7 +51,7 @@ Required properties: - compatible: should be one of: "qcom,msm8660-ebi2" "qcom,apq8060-ebi2" -- #address-cells: shoule be <2>: the first cell is the chipselect, +- #address-cells: should be <2>: the first cell is the chipselect, the second cell is the offset inside the memory range - #size-cells: should be <1> - ranges: should be set to: @@ -64,7 +64,7 @@ Required properties: - reg: two ranges of registers: EBI2 config and XMEM config areas - reg-names: should be "ebi2", "xmem" - clocks: two clocks, EBI_2X and EBI -- clock-names: shoule be "ebi2x", "ebi2" +- clock-names: should be "ebi2x", "ebi2" Optional subnodes: - Nodes inside the EBI2 will be considered device nodes. @@ -100,7 +100,7 @@ Optional properties arrays for FAST chip selects: assertion, with respect to the cycle where ADV (address valid) is asserted. 2 means 2 cycles between ADV and OE. Valid values 0, 1, 2 or 3. - qcom,xmem-read-hold-cycles: the length in cycles of the first segment of a - read transfer. For a single read trandfer this will be the time from CS + read transfer. For a single read transfer this will be the time from CS assertion to OE assertion. Valid values 0 thru 15. diff --git a/Documentation/devicetree/bindings/bus/ti,da850-mstpri.txt b/Documentation/devicetree/bindings/bus/ti,da850-mstpri.txt new file mode 100644 index 000000000000..72daefc6b4a1 --- /dev/null +++ b/Documentation/devicetree/bindings/bus/ti,da850-mstpri.txt @@ -0,0 +1,20 @@ +* Device tree bindings for Texas Instruments da8xx master peripheral + priority driver + +DA8XX SoCs feature a set of registers allowing to change the priority of all +peripherals classified as masters. + +Documentation: +OMAP-L138 (DA850) - http://www.ti.com/lit/ug/spruh82c/spruh82c.pdf + +Required properties: + +- compatible: "ti,da850-mstpri" - for da850 based boards +- reg: offset and length of the mstpri registers + +Example for da850-lcdk is shown below. + +mstpri { + compatible = "ti,da850-mstpri"; + reg = <0x14110 0x0c>; +}; diff --git a/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt b/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt index e56a1df3a9d3..dd906db34b32 100644 --- a/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt +++ b/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt @@ -16,7 +16,20 @@ Required properties: - #clock-cells: Should be <1>. The permitted clock-specifier values can be found in include/dt-bindings/clock/bcm2835.h - reg: Specifies base physical address and size of the registers -- clocks: The external oscillator clock phandle +- clocks: phandles to the parent clocks used as input to the module, in + the following order: + + - External oscillator + - DSI0 byte clock + - DSI0 DDR2 clock + - DSI0 DDR clock + - DSI1 byte clock + - DSI1 DDR2 clock + - DSI1 DDR clock + + Only external oscillator is required. The DSI clocks may + not be present, in which case their children will be + unusable. Example: diff --git a/Documentation/devicetree/bindings/clock/exynos4415-clock.txt b/Documentation/devicetree/bindings/clock/exynos4415-clock.txt deleted file mode 100644 index 847d98bae8cf..000000000000 --- a/Documentation/devicetree/bindings/clock/exynos4415-clock.txt +++ /dev/null @@ -1,38 +0,0 @@ -* Samsung Exynos4415 Clock Controller - -The Exynos4415 clock controller generates and supplies clock to various -consumer devices within the Exynos4415 SoC. - -Required properties: - -- compatible: should be one of the following: - - "samsung,exynos4415-cmu" - for the main system clocks controller - (CMU_LEFTBUS, CMU_RIGHTBUS, CMU_TOP, CMU_CPU clock domains). - - "samsung,exynos4415-cmu-dmc" - for the Exynos4415 SoC DRAM Memory - Controller (DMC) domain clock controller. - -- reg: physical base address of the controller and length of memory mapped - region. - -- #clock-cells: should be 1. - -Each clock is assigned an identifier and client nodes can use this identifier -to specify the clock which they consume. - -All available clocks are defined as preprocessor macros in -dt-bindings/clock/exynos4415.h header and can be used in device -tree sources. - -Example 1: An example of a clock controller node is listed below. - - cmu: clock-controller@10030000 { - compatible = "samsung,exynos4415-cmu"; - reg = <0x10030000 0x18000>; - #clock-cells = <1>; - }; - - cmu-dmc: clock-controller@105C0000 { - compatible = "samsung,exynos4415-cmu-dmc"; - reg = <0x105C0000 0x3000>; - #clock-cells = <1>; - }; diff --git a/Documentation/devicetree/bindings/clock/exynos5433-clock.txt b/Documentation/devicetree/bindings/clock/exynos5433-clock.txt index 63379b04e052..1dc80f8811fe 100644 --- a/Documentation/devicetree/bindings/clock/exynos5433-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5433-clock.txt @@ -79,7 +79,7 @@ Required Properties: Input clocks for fsys clock controller: - oscclk - sclk_ufs_mphy - - div_aclk_fsys_200 + - aclk_fsys_200 - sclk_pcie_100_fsys - sclk_ufsunipro_fsys - sclk_mmc2_fsys @@ -104,6 +104,10 @@ Required Properties: - sclk_decon_tv_vclk_disp - aclk_disp_333 + Input clocks for audio clock controller: + - oscclk + - fout_aud_pll + Input clocks for bus0 clock controller: - aclk_bus0_400 @@ -235,7 +239,7 @@ Example 2: Examples of clock controller nodes are listed below. clock-names = "oscclk", "sclk_ufs_mphy", - "div_aclk_fsys_200", + "aclk_fsys_200", "sclk_pcie_100_fsys", "sclk_ufsunipro_fsys", "sclk_mmc2_fsys", @@ -245,7 +249,7 @@ Example 2: Examples of clock controller nodes are listed below. "sclk_usbdrd30_fsys"; clocks = <&xxti>, <&cmu_cpif CLK_SCLK_UFS_MPHY>, - <&cmu_top CLK_DIV_ACLK_FSYS_200>, + <&cmu_top CLK_ACLK_FSYS_200>, <&cmu_top CLK_SCLK_PCIE_100_FSYS>, <&cmu_top CLK_SCLK_UFSUNIPRO_FSYS>, <&cmu_top CLK_SCLK_MMC2_FSYS>, @@ -297,6 +301,9 @@ Example 2: Examples of clock controller nodes are listed below. compatible = "samsung,exynos5433-cmu-aud"; reg = <0x114c0000 0x0b04>; #clock-cells = <1>; + + clock-names = "oscclk", "fout_aud_pll"; + clocks = <&xxti>, <&cmu_top CLK_FOUT_AUD_PLL>; }; cmu_bus0: clock-controller@13600000 { diff --git a/Documentation/devicetree/bindings/clock/hi3660-clock.txt b/Documentation/devicetree/bindings/clock/hi3660-clock.txt new file mode 100644 index 000000000000..cc9b86c35758 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/hi3660-clock.txt @@ -0,0 +1,42 @@ +* Hisilicon Hi3660 Clock Controller + +The Hi3660 clock controller generates and supplies clock to various +controllers within the Hi3660 SoC. + +Required Properties: + +- compatible: the compatible should be one of the following strings to + indicate the clock controller functionality. + + - "hisilicon,hi3660-crgctrl" + - "hisilicon,hi3660-pctrl" + - "hisilicon,hi3660-pmuctrl" + - "hisilicon,hi3660-sctrl" + - "hisilicon,hi3660-iomcu" + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes use this identifier +to specify the clock which they consume. + +All these identifier could be found in <dt-bindings/clock/hi3660-clock.h>. + +Examples: + crg_ctrl: clock-controller@fff35000 { + compatible = "hisilicon,hi3660-crgctrl", "syscon"; + reg = <0x0 0xfff35000 0x0 0x1000>; + #clock-cells = <1>; + }; + + uart0: serial@fdf02000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x0 0xfdf02000 0x0 0x1000>; + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&crg_ctrl HI3660_CLK_MUX_UART0>, + <&crg_ctrl HI3660_PCLK>; + clock-names = "uartclk", "apb_pclk"; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/hi3519-crg.txt b/Documentation/devicetree/bindings/clock/hisi-crg.txt index acd1f235d548..cc60b3d423f3 100644 --- a/Documentation/devicetree/bindings/clock/hi3519-crg.txt +++ b/Documentation/devicetree/bindings/clock/hisi-crg.txt @@ -1,7 +1,7 @@ -* Hisilicon Hi3519 Clock and Reset Generator(CRG) +* HiSilicon Clock and Reset Generator(CRG) -The Hi3519 CRG module provides clock and reset signals to various -controllers within the SoC. +The CRG module provides clock and reset signals to various +modules within the SoC. This binding uses the following bindings: Documentation/devicetree/bindings/clock/clock-bindings.txt @@ -10,7 +10,11 @@ This binding uses the following bindings: Required Properties: - compatible: should be one of the following. - - "hisilicon,hi3519-crg" - controller compatible with Hi3519 SoC. + - "hisilicon,hi3516cv300-crg" + - "hisilicon,hi3516cv300-sysctrl" + - "hisilicon,hi3519-crg" + - "hisilicon,hi3798cv200-crg" + - "hisilicon,hi3798cv200-sysctrl" - reg: physical base address of the controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/clock/idt,versaclock5.txt b/Documentation/devicetree/bindings/clock/idt,versaclock5.txt new file mode 100644 index 000000000000..87e9c47a89a3 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/idt,versaclock5.txt @@ -0,0 +1,65 @@ +Binding for IDT VersaClock5 programmable i2c clock generator. + +The IDT VersaClock5 are programmable i2c clock generators providing +from 3 to 12 output clocks. + +==I2C device node== + +Required properties: +- compatible: shall be one of "idt,5p49v5923" , "idt,5p49v5933". +- reg: i2c device address, shall be 0x68 or 0x6a. +- #clock-cells: from common clock binding; shall be set to 1. +- clocks: from common clock binding; list of parent clock handles, + - 5p49v5923: (required) either or both of XTAL or CLKIN + reference clock. + - 5p49v5933: (optional) property not present (internal + Xtal used) or CLKIN reference + clock. +- clock-names: from common clock binding; clock input names, can be + - 5p49v5923: (required) either or both of "xin", "clkin". + - 5p49v5933: (optional) property not present or "clkin". + +==Mapping between clock specifier and physical pins== + +When referencing the provided clock in the DT using phandle and +clock specifier, the following mapping applies: + +5P49V5923: + 0 -- OUT0_SEL_I2CB + 1 -- OUT1 + 2 -- OUT2 + +5P49V5933: + 0 -- OUT0_SEL_I2CB + 1 -- OUT1 + 2 -- OUT4 + +==Example== + +/* 25MHz reference crystal */ +ref25: ref25m { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; +}; + +i2c-master-node { + + /* IDT 5P49V5923 i2c clock generator */ + vc5: clock-generator@6a { + compatible = "idt,5p49v5923"; + reg = <0x6a>; + #clock-cells = <1>; + + /* Connect XIN input to 25MHz reference */ + clocks = <&ref25m>; + clock-names = "xin"; + }; +}; + +/* Consumer referencing the 5P49V5923 pin OUT1 */ +consumer { + ... + clocks = <&vc5 1>; + ... +} diff --git a/Documentation/devicetree/bindings/clock/imx31-clock.txt b/Documentation/devicetree/bindings/clock/imx31-clock.txt index 19df842c694f..8163d565f697 100644 --- a/Documentation/devicetree/bindings/clock/imx31-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx31-clock.txt @@ -77,7 +77,7 @@ Examples: clks: ccm@53f80000{ compatible = "fsl,imx31-ccm"; reg = <0x53f80000 0x4000>; - interrupts = <0 31 0x04 0 53 0x04>; + interrupts = <31>, <53>; #clock-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt index 520562a7dc2a..c7b4e3a6b2c6 100644 --- a/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt +++ b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt @@ -7,6 +7,7 @@ Required properties: - compatible : must be "marvell,armada-370-corediv-clock", "marvell,armada-375-corediv-clock", "marvell,armada-380-corediv-clock", + "marvell,mv98dx3236-corediv-clock", - reg : must be the register address of Core Divider control register - #clock-cells : from common clock binding; shall be set to 1 diff --git a/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt index 99c214660bdc..7f28506eaee7 100644 --- a/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt +++ b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt @@ -3,6 +3,7 @@ Device Tree Clock bindings for cpu clock of Marvell EBU platforms Required properties: - compatible : shall be one of the following: "marvell,armada-xp-cpu-clock" - cpu clocks for Armada XP + "marvell,mv98dx3236-cpu-clock" - cpu clocks for 98DX3236 SoC - reg : Address and length of the clock complex register set, followed by address and length of the PMU DFS registers - #clock-cells : should be set to 1. diff --git a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt index cb8542d910b3..5142efc8099d 100644 --- a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt +++ b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt @@ -117,7 +117,7 @@ ID Clock Peripheral 25 tdm Time Division Mplx 28 xor1 XOR DMA 1 29 sata1lnk -30 sata1 SATA Host 0 +30 sata1 SATA Host 1 The following is a list of provided IDs for Dove: ID Clock Peripheral diff --git a/Documentation/devicetree/bindings/clock/oxnas,stdclk.txt b/Documentation/devicetree/bindings/clock/oxnas,stdclk.txt index 208cca6ac4ec..b652f3fb7796 100644 --- a/Documentation/devicetree/bindings/clock/oxnas,stdclk.txt +++ b/Documentation/devicetree/bindings/clock/oxnas,stdclk.txt @@ -5,22 +5,15 @@ Please also refer to clock-bindings.txt in this directory for common clock bindings usage. Required properties: -- compatible: Should be "oxsemi,ox810se-stdclk" +- compatible: For OX810SE, should be "oxsemi,ox810se-stdclk" + For OX820, should be "oxsemi,ox820-stdclk" - #clock-cells: 1, see below Parent node should have the following properties : -- compatible: Should be "oxsemi,ox810se-sys-ctrl", "syscon", "simple-mfd" - -For OX810SE, the clock indices are : - - 0: LEON - - 1: DMA_SGDMA - - 2: CIPHER - - 3: SATA - - 4: AUDIO - - 5: USBMPH - - 6: ETHA - - 7: PCIA - - 8: NAND +- compatible: For OX810SE, should be + "oxsemi,ox810se-sys-ctrl", "syscon", "simple-mfd" + For OX820, should be + "oxsemi,ox820-sys-ctrl", "syscon", "simple-mfd" example: diff --git a/Documentation/devicetree/bindings/clock/qcom,gcc.txt b/Documentation/devicetree/bindings/clock/qcom,gcc.txt index 3cf44217068e..5b4dfc1ea54f 100644 --- a/Documentation/devicetree/bindings/clock/qcom,gcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,gcc.txt @@ -14,6 +14,7 @@ Required properties : "qcom,gcc-msm8974" "qcom,gcc-msm8974pro" "qcom,gcc-msm8974pro-ac" + "qcom,gcc-msm8994" "qcom,gcc-msm8996" "qcom,gcc-mdm9615" diff --git a/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt b/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt new file mode 100644 index 000000000000..a7235e9e1c97 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt @@ -0,0 +1,38 @@ +Qualcomm RPM Clock Controller Binding +------------------------------------------------ +The RPM is a dedicated hardware engine for managing the shared +SoC resources in order to keep the lowest power profile. It +communicates with other hardware subsystems via shared memory +and accepts clock requests, aggregates the requests and turns +the clocks on/off or scales them on demand. + +Required properties : +- compatible : shall contain only one of the following. The generic + compatible "qcom,rpmcc" should be also included. + + "qcom,rpmcc-msm8916", "qcom,rpmcc" + "qcom,rpmcc-msm8974", "qcom,rpmcc" + "qcom,rpmcc-apq8064", "qcom,rpmcc" + +- #clock-cells : shall contain 1 + +Example: + smd { + compatible = "qcom,smd"; + + rpm { + interrupts = <0 168 1>; + qcom,ipc = <&apcs 8 0>; + qcom,smd-edge = <15>; + + rpm_requests { + compatible = "qcom,rpm-msm8916"; + qcom,smd-channels = "rpm_requests"; + + rpmcc: clock-controller { + compatible = "qcom,rpmcc-msm8916", "qcom,rpmcc"; + #clock-cells = <1>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/qoriq-clock.txt b/Documentation/devicetree/bindings/clock/qoriq-clock.txt index 16a3ec433119..aa3526f229a7 100644 --- a/Documentation/devicetree/bindings/clock/qoriq-clock.txt +++ b/Documentation/devicetree/bindings/clock/qoriq-clock.txt @@ -31,7 +31,11 @@ Required properties: * "fsl,t4240-clockgen" * "fsl,b4420-clockgen" * "fsl,b4860-clockgen" + * "fsl,ls1012a-clockgen" * "fsl,ls1021a-clockgen" + * "fsl,ls1043a-clockgen" + * "fsl,ls1046a-clockgen" + * "fsl,ls2080a-clockgen" Chassis-version clock strings include: * "fsl,qoriq-clockgen-1.0": for chassis 1.0 clocks * "fsl,qoriq-clockgen-2.0": for chassis 2.0 clocks diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt index 394d725ac7e0..f4f944d81308 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt @@ -13,6 +13,8 @@ They provide the following functionalities: Required Properties: - compatible: Must be one of: + - "renesas,r8a7743-cpg-mssr" for the r8a7743 SoC (RZ/G1M) + - "renesas,r8a7745-cpg-mssr" for the r8a7745 SoC (RZ/G1E) - "renesas,r8a7795-cpg-mssr" for the r8a7795 SoC (R-Car H3) - "renesas,r8a7796-cpg-mssr" for the r8a7796 SoC (R-Car M3-W) @@ -22,8 +24,9 @@ Required Properties: - clocks: References to external parent clocks, one entry for each entry in clock-names - clock-names: List of external parent clock names. Valid names are: - - "extal" (r8a7795, r8a7796) + - "extal" (r8a7743, r8a7745, r8a7795, r8a7796) - "extalr" (r8a7795, r8a7796) + - "usb_extal" (r8a7743, r8a7745) - #clock-cells: Must be 2 - For CPG core clocks, the two clock specifier cells must be "CPG_CORE" @@ -39,6 +42,10 @@ Required Properties: Domain bindings in Documentation/devicetree/bindings/power/power_domain.txt. + - #reset-cells: Must be 1 + - The single reset specifier cell must be the module number, as defined + in the datasheet. + Examples -------- @@ -52,6 +59,7 @@ Examples clock-names = "extal", "extalr"; #clock-cells = <2>; #power-domain-cells = <0>; + #reset-cells = <1>; }; @@ -66,5 +74,6 @@ Examples dmas = <&dmac1 0x13>, <&dmac1 0x12>; dma-names = "tx", "rx"; power-domains = <&cpg>; + resets = <&cpg 310>; status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk1108-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk1108-cru.txt new file mode 100644 index 000000000000..4da126116cf0 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk1108-cru.txt @@ -0,0 +1,59 @@ +* Rockchip RK1108 Clock and Reset Unit + +The RK1108 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk1108-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changeable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk1108-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "ext_vip" - external VIP clock - optional + - "ext_i2s" - external I2S clock - optional + - "ext_gmac" - external GMAC clock - optional + - "hdmiphy" - external clock input derived from HDMI PHY - optional + - "usbphy" - external clock input derived from USB PHY - optional + +Example: Clock controller node: + + cru: cru@20200000 { + compatible = "rockchip,rk1108-cru"; + reg = <0x20200000 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@10230000 { + compatible = "rockchip,rk1108-uart", "snps,dw-apb-uart"; + reg = <0x10230000 0x100>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt new file mode 100644 index 000000000000..e71c675ba5da --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt @@ -0,0 +1,57 @@ +* Rockchip RK3328 Clock and Reset Unit + +The RK3328 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3328-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changeable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3328-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "clkin_i2s" - external I2S clock - optional, + - "gmac_clkin" - external GMAC clock - optional + - "phy_50m_out" - output clock of the pll in the mac phy + +Example: Clock controller node: + + cru: clock-controller@ff440000 { + compatible = "rockchip,rk3328-cru"; + reg = <0x0 0xff440000 0x0 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@ff120000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff120000 0x100>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.txt index 3888dd33fcbd..3bc56fae90ac 100644 --- a/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.txt +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.txt @@ -13,6 +13,12 @@ Required Properties: - #clock-cells: should be 1. - #reset-cells: should be 1. +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files". + It is used for GRF muxes, if missing any muxes present in the GRF will not + be available. + Each clock is assigned an identifier and client nodes can use this identifier to specify the clock which they consume. All available clocks are defined as preprocessor macros in the dt-bindings/clock/rk3399-cru.h headers and can be diff --git a/Documentation/devicetree/bindings/clock/st,stm32-rcc.txt b/Documentation/devicetree/bindings/clock/st,stm32-rcc.txt index c209de6cfadb..b240121d2ac9 100644 --- a/Documentation/devicetree/bindings/clock/st,stm32-rcc.txt +++ b/Documentation/devicetree/bindings/clock/st,stm32-rcc.txt @@ -7,7 +7,10 @@ Please refer to clock-bindings.txt for common clock controller binding usage. Please also refer to reset.txt for common reset controller binding usage. Required properties: -- compatible: Should be "st,stm32f42xx-rcc" +- compatible: Should be: + "st,stm32f42xx-rcc" + "st,stm32f469-rcc" + "st,stm32f746-rcc" - reg: should be register base and length as documented in the datasheet - #reset-cells: 1, see below @@ -15,6 +18,9 @@ Required properties: property, containing a phandle to the clock device node, an index selecting between gated clocks and other clocks and an index specifying the clock to use. +- clocks: External oscillator clock phandle + - high speed external clock signal (HSE) + - external I2S clock (I2S_CKIN) Example: @@ -23,6 +29,7 @@ Example: #clock-cells = <2> compatible = "st,stm32f42xx-rcc", "st,stm32-rcc"; reg = <0x40023800 0x400>; + clocks = <&clk_hse>, <&clk_i2s_ckin>; }; Specifying gated clocks @@ -64,6 +71,38 @@ The secondary index is bound with the following magic numbers: 0 SYSTICK 1 FCLK + 2 CLK_LSI (low-power clock source) + 3 CLK_LSE (generated from a 32.768 kHz low-speed external + crystal or ceramic resonator) + 4 CLK_HSE_RTC (HSE division factor for RTC clock) + 5 CLK_RTC (real-time clock) + 6 PLL_VCO_I2S (vco frequency of I2S pll) + 7 PLL_VCO_SAI (vco frequency of SAI pll) + 8 CLK_LCD (LCD-TFT) + 9 CLK_I2S (I2S clocks) + 10 CLK_SAI1 (audio clocks) + 11 CLK_SAI2 + 12 CLK_I2SQ_PDIV (post divisor of pll i2s q divisor) + 13 CLK_SAIQ_PDIV (post divisor of pll sai q divisor) + + 14 CLK_HSI (Internal ocscillator clock) + 15 CLK_SYSCLK (System Clock) + 16 CLK_HDMI_CEC (HDMI-CEC clock) + 17 CLK_SPDIF (SPDIF-Rx clock) + 18 CLK_USART1 (U(s)arts clocks) + 19 CLK_USART2 + 20 CLK_USART3 + 21 CLK_UART4 + 22 CLK_UART5 + 23 CLK_USART6 + 24 CLK_UART7 + 25 CLK_UART8 + 26 CLK_I2C1 (I2S clocks) + 27 CLK_I2C2 + 28 CLK_I2C3 + 29 CLK_I2C4 + 30 CLK_LPTIMER (LPTimer1 clock) +) Example: diff --git a/Documentation/devicetree/bindings/clock/stericsson,abx500.txt b/Documentation/devicetree/bindings/clock/stericsson,abx500.txt new file mode 100644 index 000000000000..dbaa886b223e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/stericsson,abx500.txt @@ -0,0 +1,20 @@ +Clock bindings for ST-Ericsson ABx500 clocks + +Required properties : +- compatible : shall contain the following: + "stericsson,ab8500-clk" +- #clock-cells should be <1> + +The ABx500 clocks need to be placed as a subnode of an AB8500 +device node, see mfd/ab8500.txt + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/ste-ab8500.h header and can be used in device +tree sources. + +Example: + +clock-controller { + compatible = "stericsson,ab8500-clk"; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/sun9i-de.txt b/Documentation/devicetree/bindings/clock/sun9i-de.txt new file mode 100644 index 000000000000..fb18f327b97a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sun9i-de.txt @@ -0,0 +1,28 @@ +Allwinner A80 Display Engine Clock Control Binding +-------------------------------------------------- + +Required properties : +- compatible: must contain one of the following compatibles: + - "allwinner,sun9i-a80-de-clks" + +- reg: Must contain the registers base address and length +- clocks: phandle to the clocks feeding the display engine subsystem. + Three are needed: + - "mod": the display engine module clock + - "dram": the DRAM bus clock for the system + - "bus": the bus clock for the whole display engine subsystem +- clock-names: Must contain the clock names described just above +- resets: phandle to the reset control for the display engine subsystem. +- #clock-cells : must contain 1 +- #reset-cells : must contain 1 + +Example: +de_clocks: clock@3000000 { + compatible = "allwinner,sun9i-a80-de-clks"; + reg = <0x03000000 0x30>; + clocks = <&ccu CLK_DE>, <&ccu CLK_SDRAM>, <&ccu CLK_BUS_DE>; + clock-names = "mod", "dram", "bus"; + resets = <&ccu RST_BUS_DE>; + #clock-cells = <1>; + #reset-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/sun9i-usb.txt b/Documentation/devicetree/bindings/clock/sun9i-usb.txt new file mode 100644 index 000000000000..3564bd4f2a20 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sun9i-usb.txt @@ -0,0 +1,24 @@ +Allwinner A80 USB Clock Control Binding +--------------------------------------- + +Required properties : +- compatible: must contain one of the following compatibles: + - "allwinner,sun9i-a80-usb-clocks" + +- reg: Must contain the registers base address and length +- clocks: phandle to the clocks feeding the USB subsystem. Two are needed: + - "bus": the bus clock for the whole USB subsystem + - "hosc": the high frequency oscillator (usually at 24MHz) +- clock-names: Must contain the clock names described just above +- #clock-cells : must contain 1 +- #reset-cells : must contain 1 + +Example: +usb_clocks: clock@a08000 { + compatible = "allwinner,sun9i-a80-usb-clks"; + reg = <0x00a08000 0x8>; + clocks = <&ccu CLK_BUS_USB>, <&osc24M>; + clock-names = "bus", "hosc"; + #clock-cells = <1>; + #reset-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt index 3868458a5feb..bae5668cf427 100644 --- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt +++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt @@ -7,6 +7,9 @@ Required properties : - "allwinner,sun8i-a23-ccu" - "allwinner,sun8i-a33-ccu" - "allwinner,sun8i-h3-ccu" + - "allwinner,sun8i-v3s-ccu" + - "allwinner,sun9i-a80-ccu" + - "allwinner,sun50i-a64-ccu" - reg: Must contain the registers base address and length - clocks: phandle to the oscillators feeding the CCU. Two are needed: diff --git a/Documentation/devicetree/bindings/clock/ti,cdce925.txt b/Documentation/devicetree/bindings/clock/ti,cdce925.txt index 4c7669ad681b..0d01f2d5cc36 100644 --- a/Documentation/devicetree/bindings/clock/ti,cdce925.txt +++ b/Documentation/devicetree/bindings/clock/ti,cdce925.txt @@ -1,15 +1,22 @@ -Binding for TO CDCE925 programmable I2C clock synthesizers. +Binding for TI CDCE913/925/937/949 programmable I2C clock synthesizers. Reference This binding uses the common clock binding[1]. [1] Documentation/devicetree/bindings/clock/clock-bindings.txt -[2] http://www.ti.com/product/cdce925 +[2] http://www.ti.com/product/cdce913 +[3] http://www.ti.com/product/cdce925 +[4] http://www.ti.com/product/cdce937 +[5] http://www.ti.com/product/cdce949 The driver provides clock sources for each output Y1 through Y5. Required properties: - - compatible: Shall be "ti,cdce925" + - compatible: Shall be one of the following: + - "ti,cdce913": 1-PLL, 3 Outputs + - "ti,cdce925": 2-PLL, 5 Outputs + - "ti,cdce937": 3-PLL, 7 Outputs + - "ti,cdce949": 4-PLL, 9 Outputs - reg: I2C device address. - clocks: Points to a fixed parent clock that provides the input frequency. - #clock-cells: From common clock bindings: Shall be 1. @@ -18,7 +25,7 @@ Optional properties: - xtal-load-pf: Crystal load-capacitor value to fine-tune performance on a board, or to compensate for external influences. -For both PLL1 and PLL2 an optional child node can be used to specify spread +For all PLL1, PLL2, ... an optional child node can be used to specify spread spectrum clocking parameters for a board. - spread-spectrum: SSC mode as defined in the data sheet. - spread-spectrum-center: Use "centered" mode instead of "max" mode. When diff --git a/Documentation/devicetree/bindings/clock/zx296718-clk.txt b/Documentation/devicetree/bindings/clock/zx296718-clk.txt index 8c18b7b237bf..4ad703808407 100644 --- a/Documentation/devicetree/bindings/clock/zx296718-clk.txt +++ b/Documentation/devicetree/bindings/clock/zx296718-clk.txt @@ -13,6 +13,9 @@ Required properties: "zte,zx296718-lsp1crm": zx296718 device level clock selection and gating + "zte,zx296718-audiocrm": + zx296718 audio clock selection, divider and gating + - reg: Address and length of the register set The clock consumer should specify the desired clock by having the clock diff --git a/Documentation/devicetree/bindings/cpufreq/brcm,stb-avs-cpu-freq.txt b/Documentation/devicetree/bindings/cpufreq/brcm,stb-avs-cpu-freq.txt new file mode 100644 index 000000000000..af2385795d78 --- /dev/null +++ b/Documentation/devicetree/bindings/cpufreq/brcm,stb-avs-cpu-freq.txt @@ -0,0 +1,78 @@ +Broadcom AVS mail box and interrupt register bindings +===================================================== + +A total of three DT nodes are required. One node (brcm,avs-cpu-data-mem) +references the mailbox register used to communicate with the AVS CPU[1]. The +second node (brcm,avs-cpu-l2-intr) is required to trigger an interrupt on +the AVS CPU. The interrupt tells the AVS CPU that it needs to process a +command sent to it by a driver. Interrupting the AVS CPU is mandatory for +commands to be processed. + +The interface also requires a reference to the AVS host interrupt controller, +so a driver can react to interrupts generated by the AVS CPU whenever a command +has been processed. See [2] for more information on the brcm,l2-intc node. + +[1] The AVS CPU is an independent co-processor that runs proprietary +firmware. On some SoCs, this firmware supports DFS and DVFS in addition to +Adaptive Voltage Scaling. + +[2] Documentation/devicetree/bindings/interrupt-controller/brcm,l2-intc.txt + + +Node brcm,avs-cpu-data-mem +-------------------------- + +Required properties: +- compatible: must include: brcm,avs-cpu-data-mem and + should include: one of brcm,bcm7271-avs-cpu-data-mem or + brcm,bcm7268-avs-cpu-data-mem +- reg: Specifies base physical address and size of the registers. +- interrupts: The interrupt that the AVS CPU will use to interrupt the host + when a command completed. +- interrupt-parent: The interrupt controller the above interrupt is routed + through. +- interrupt-names: The name of the interrupt used to interrupt the host. + +Optional properties: +- None + +Node brcm,avs-cpu-l2-intr +------------------------- + +Required properties: +- compatible: must include: brcm,avs-cpu-l2-intr and + should include: one of brcm,bcm7271-avs-cpu-l2-intr or + brcm,bcm7268-avs-cpu-l2-intr +- reg: Specifies base physical address and size of the registers. + +Optional properties: +- None + + +Example +======= + + avs_host_l2_intc: interrupt-controller@f04d1200 { + #interrupt-cells = <1>; + compatible = "brcm,l2-intc"; + interrupt-parent = <&intc>; + reg = <0xf04d1200 0x48>; + interrupt-controller; + interrupts = <0x0 0x19 0x0>; + interrupt-names = "avs"; + }; + + avs-cpu-data-mem@f04c4000 { + compatible = "brcm,bcm7271-avs-cpu-data-mem", + "brcm,avs-cpu-data-mem"; + reg = <0xf04c4000 0x60>; + interrupts = <0x1a>; + interrupt-parent = <&avs_host_l2_intc>; + interrupt-names = "sw_intr"; + }; + + avs-cpu-l2-intr@f04d1100 { + compatible = "brcm,bcm7271-avs-cpu-l2-intr", + "brcm,avs-cpu-l2-intr"; + reg = <0xf04d1100 0x10>; + }; diff --git a/Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt b/Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt new file mode 100644 index 000000000000..ba0e15ad5bd9 --- /dev/null +++ b/Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt @@ -0,0 +1,128 @@ +TI CPUFreq and OPP bindings +================================ + +Certain TI SoCs, like those in the am335x, am437x, am57xx, and dra7xx +families support different OPPs depending on the silicon variant in use. +The ti-cpufreq driver can use revision and an efuse value from the SoC to +provide the OPP framework with supported hardware information. This is +used to determine which OPPs from the operating-points-v2 table get enabled +when it is parsed by the OPP framework. + +Required properties: +-------------------- +In 'cpus' nodes: +- operating-points-v2: Phandle to the operating-points-v2 table to use. + +In 'operating-points-v2' table: +- compatible: Should be + - 'operating-points-v2-ti-cpu' for am335x, am43xx, and dra7xx/am57xx SoCs +- syscon: A phandle pointing to a syscon node representing the control module + register space of the SoC. + +Optional properties: +-------------------- +For each opp entry in 'operating-points-v2' table: +- opp-supported-hw: Two bitfields indicating: + 1. Which revision of the SoC the OPP is supported by + 2. Which eFuse bits indicate this OPP is available + + A bitwise AND is performed against these values and if any bit + matches, the OPP gets enabled. + +Example: +-------- + +/* From arch/arm/boot/dts/am33xx.dtsi */ +cpus { + #address-cells = <1>; + #size-cells = <0>; + cpu@0 { + compatible = "arm,cortex-a8"; + device_type = "cpu"; + reg = <0>; + + operating-points-v2 = <&cpu0_opp_table>; + + clocks = <&dpll_mpu_ck>; + clock-names = "cpu"; + + clock-latency = <300000>; /* From omap-cpufreq driver */ + }; +}; + +/* + * cpu0 has different OPPs depending on SoC revision and some on revisions + * 0x2 and 0x4 have eFuse bits that indicate if they are available or not + */ +cpu0_opp_table: opp-table { + compatible = "operating-points-v2-ti-cpu"; + syscon = <&scm_conf>; + + /* + * The three following nodes are marked with opp-suspend + * because they can not be enabled simultaneously on a + * single SoC. + */ + opp50@300000000 { + opp-hz = /bits/ 64 <300000000>; + opp-microvolt = <950000 931000 969000>; + opp-supported-hw = <0x06 0x0010>; + opp-suspend; + }; + + opp100@275000000 { + opp-hz = /bits/ 64 <275000000>; + opp-microvolt = <1100000 1078000 1122000>; + opp-supported-hw = <0x01 0x00FF>; + opp-suspend; + }; + + opp100@300000000 { + opp-hz = /bits/ 64 <300000000>; + opp-microvolt = <1100000 1078000 1122000>; + opp-supported-hw = <0x06 0x0020>; + opp-suspend; + }; + + opp100@500000000 { + opp-hz = /bits/ 64 <500000000>; + opp-microvolt = <1100000 1078000 1122000>; + opp-supported-hw = <0x01 0xFFFF>; + }; + + opp100@600000000 { + opp-hz = /bits/ 64 <600000000>; + opp-microvolt = <1100000 1078000 1122000>; + opp-supported-hw = <0x06 0x0040>; + }; + + opp120@600000000 { + opp-hz = /bits/ 64 <600000000>; + opp-microvolt = <1200000 1176000 1224000>; + opp-supported-hw = <0x01 0xFFFF>; + }; + + opp120@720000000 { + opp-hz = /bits/ 64 <720000000>; + opp-microvolt = <1200000 1176000 1224000>; + opp-supported-hw = <0x06 0x0080>; + }; + + oppturbo@720000000 { + opp-hz = /bits/ 64 <720000000>; + opp-microvolt = <1260000 1234800 1285200>; + opp-supported-hw = <0x01 0xFFFF>; + }; + + oppturbo@800000000 { + opp-hz = /bits/ 64 <800000000>; + opp-microvolt = <1260000 1234800 1285200>; + opp-supported-hw = <0x06 0x0100>; + }; + + oppnitro@1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt = <1325000 1298500 1351500>; + opp-supported-hw = <0x04 0x0200>; + }; +}; diff --git a/Documentation/devicetree/bindings/crypto/brcm,spu-crypto.txt b/Documentation/devicetree/bindings/crypto/brcm,spu-crypto.txt new file mode 100644 index 000000000000..29b6007568eb --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/brcm,spu-crypto.txt @@ -0,0 +1,22 @@ +The Broadcom Secure Processing Unit (SPU) hardware supports symmetric +cryptographic offload for Broadcom SoCs. A SoC may have multiple SPU hardware +blocks. + +Required properties: +- compatible: Should be one of the following: + brcm,spum-crypto - for devices with SPU-M hardware + brcm,spu2-crypto - for devices with SPU2 hardware + brcm,spu2-v2-crypto - for devices with enhanced SPU2 hardware features like SHA3 + and Rabin Fingerprint support + brcm,spum-nsp-crypto - for the Northstar Plus variant of the SPU-M hardware + +- reg: Should contain SPU registers location and length. +- mboxes: The mailbox channel to be used to communicate with the SPU. + Mailbox channels correspond to DMA rings on the device. + +Example: + crypto@612d0000 { + compatible = "brcm,spum-crypto"; + reg = <0 0x612d0000 0 0x900>; + mboxes = <&pdc0 0>; + }; diff --git a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt index adeca34c5a33..10a425f451fc 100644 --- a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt +++ b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt @@ -123,6 +123,9 @@ PROPERTIES EXAMPLE + +iMX6QDL/SX requires four clocks + crypto@300000 { compatible = "fsl,sec-v4.0"; fsl,sec-era = <2>; @@ -139,6 +142,23 @@ EXAMPLE clock-names = "mem", "aclk", "ipg", "emi_slow"; }; + +iMX6UL does only require three clocks + + crypto: caam@2140000 { + compatible = "fsl,sec-v4.0"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x2140000 0x3c000>; + ranges = <0 0x2140000 0x3c000>; + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&clks IMX6UL_CLK_CAAM_MEM>, + <&clks IMX6UL_CLK_CAAM_ACLK>, + <&clks IMX6UL_CLK_CAAM_IPG>; + clock-names = "mem", "aclk", "ipg"; + }; + ===================================================================== Job Ring (JR) Node diff --git a/Documentation/devicetree/bindings/crypto/mediatek-crypto.txt b/Documentation/devicetree/bindings/crypto/mediatek-crypto.txt new file mode 100644 index 000000000000..c204725e5873 --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/mediatek-crypto.txt @@ -0,0 +1,27 @@ +MediaTek cryptographic accelerators + +Required properties: +- compatible: Should be "mediatek,eip97-crypto" +- reg: Address and length of the register set for the device +- interrupts: Should contain the five crypto engines interrupts in numeric + order. These are global system and four descriptor rings. +- clocks: the clock used by the core +- clock-names: the names of the clock listed in the clocks property. These are + "ethif", "cryp" +- power-domains: Must contain a reference to the PM domain. + + +Example: + crypto: crypto@1b240000 { + compatible = "mediatek,eip97-crypto"; + reg = <0 0x1b240000 0 0x20000>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 83 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 84 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 91 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 97 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_ETHIF_SEL>, + <ðsys CLK_ETHSYS_CRYPTO>; + clock-names = "ethif","cryp"; + power-domains = <&scpsys MT2701_POWER_DOMAIN_ETH>; + }; diff --git a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt index d3ec8e676b6b..d085ef90d27c 100644 --- a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt +++ b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt @@ -123,6 +123,20 @@ Detailed correlation between sub-blocks and power line according to Exynos SoC: |--- FSYS |--- FSYS2 +- In case of Exynos5433, there is VDD_INT power line as following: + VDD_INT |--- G2D (parent device) + |--- MSCL + |--- GSCL + |--- JPEG + |--- MFC + |--- HEVC + |--- BUS0 + |--- BUS1 + |--- BUS2 + |--- PERIS (Fixed clock rate) + |--- PERIC (Fixed clock rate) + |--- FSYS (Fixed clock rate) + Example1: Show the AXI buses of Exynos3250 SoC. Exynos3250 divides the buses to power line (regulator). The MIF (Memory Interface) AXI bus is used to diff --git a/Documentation/devicetree/bindings/display/amlogic,meson-vpu.txt b/Documentation/devicetree/bindings/display/amlogic,meson-vpu.txt new file mode 100644 index 000000000000..00f74bad1e95 --- /dev/null +++ b/Documentation/devicetree/bindings/display/amlogic,meson-vpu.txt @@ -0,0 +1,112 @@ +Amlogic Meson Display Controller +================================ + +The Amlogic Meson Display controller is composed of several components +that are going to be documented below: + +DMC|---------------VPU (Video Processing Unit)----------------|------HHI------| + | vd1 _______ _____________ _________________ | | +D |-------| |----| | | | | HDMI PLL | +D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK | +R |-------| |----| Processing | | | | | + | osd2 | | | |---| Enci ----------|----|-----VDAC------| +R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----| +A | osd1 | | | Blenders | | Encl ----------|----|---------------| +M |-------|______|----|____________| |________________| | | +___|__________________________________________________________|_______________| + + +VIU: Video Input Unit +--------------------- + +The Video Input Unit is in charge of the pixel scanout from the DDR memory. +It fetches the frames addresses, stride and parameters from the "Canvas" memory. +This part is also in charge of the CSC (Colorspace Conversion). +It can handle 2 OSD Planes and 2 Video Planes. + +VPP: Video Post Processing +-------------------------- + +The Video Post Processing is in charge of the scaling and blending of the +various planes into a single pixel stream. +There is a special "pre-blending" used by the video planes with a dedicated +scaler and a "post-blending" to merge with the OSD Planes. +The OSD planes also have a dedicated scaler for one of the OSD. + +VENC: Video Encoders +-------------------- + +The VENC is composed of the multiple pixel encoders : + - ENCI : Interlace Video encoder for CVBS and Interlace HDMI + - ENCP : Progressive Video Encoder for HDMI + - ENCL : LCD LVDS Encoder +The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock +tree and provides the scanout clock to the VPP and VIU. +The ENCI is connected to a single VDAC for Composite Output. +The ENCI and ENCP are connected to an on-chip HDMI Transceiver. + +Device Tree Bindings: +--------------------- + +VPU: Video Processing Unit +-------------------------- + +Required properties: +- compatible: value should be different for each SoC family as : + - GXBB (S905) : "amlogic,meson-gxbb-vpu" + - GXL (S905X, S905D) : "amlogic,meson-gxl-vpu" + - GXM (S912) : "amlogic,meson-gxm-vpu" + followed by the common "amlogic,meson-gx-vpu" +- reg: base address and size of he following memory-mapped regions : + - vpu + - hhi + - dmc +- reg-names: should contain the names of the previous memory regions +- interrupts: should contain the VENC Vsync interrupt number + +Required nodes: + +The connections to the VPU output video ports are modeled using the OF graph +bindings specified in Documentation/devicetree/bindings/graph.txt. + +The following table lists for each supported model the port number +corresponding to each VPU output. + + Port 0 Port 1 +----------------------------------------- + S905 (GXBB) CVBS VDAC HDMI-TX + S905X (GXL) CVBS VDAC HDMI-TX + S905D (GXL) CVBS VDAC HDMI-TX + S912 (GXM) CVBS VDAC HDMI-TX + +Example: + +tv-connector { + compatible = "composite-video-connector"; + + port { + tv_connector_in: endpoint { + remote-endpoint = <&cvbs_vdac_out>; + }; + }; +}; + +vpu: vpu@d0100000 { + compatible = "amlogic,meson-gxbb-vpu"; + reg = <0x0 0xd0100000 0x0 0x100000>, + <0x0 0xc883c000 0x0 0x1000>, + <0x0 0xc8838000 0x0 0x1000>; + reg-names = "vpu", "hhi", "dmc"; + interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>; + #address-cells = <1>; + #size-cells = <0>; + + /* CVBS VDAC output port */ + port@0 { + reg = <0>; + + cvbs_vdac_out: endpoint { + remote-endpoint = <&tv_connector_in>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/arm,pl11x.txt b/Documentation/devicetree/bindings/display/arm,pl11x.txt index 3e3039a8a253..ef89ab46b2c9 100644 --- a/Documentation/devicetree/bindings/display/arm,pl11x.txt +++ b/Documentation/devicetree/bindings/display/arm,pl11x.txt @@ -22,7 +22,7 @@ Required properties: - clocks: contains phandle and clock specifier pairs for the entries in the clock-names property. See - Documentation/devicetree/binding/clock/clock-bindings.txt + Documentation/devicetree/bindings/clock/clock-bindings.txt Optional properties: diff --git a/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt b/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt index a5ea451e67fc..34c7fddcea39 100644 --- a/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt +++ b/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt @@ -43,12 +43,31 @@ Required properties for DPI: - port: Port node with a single endpoint connecting to the panel device, as defined in [1] +Required properties for VEC: +- compatible: Should be "brcm,bcm2835-vec" +- reg: Physical base address and length of the registers +- clocks: The core clock the unit runs on +- interrupts: The interrupt number + See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt + Required properties for V3D: - compatible: Should be "brcm,bcm2835-v3d" - reg: Physical base address and length of the V3D's registers - interrupts: The interrupt number See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt +Required properties for DSI: +- compatible: Should be "brcm,bcm2835-dsi0" or "brcm,bcm2835-dsi1" +- reg: Physical base address and length of the DSI block's registers +- interrupts: The interrupt number + See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt +- clocks: a) phy: The DSI PLL clock feeding the DSI analog PHY + b) escape: The DSI ESC clock from CPRMAN + c) pixel: The DSI pixel clock from CPRMAN +- clock-output-names: + The 3 clocks output from the DSI analog PHY: dsi[01]_byte, + dsi[01]_ddr2, and dsi[01]_ddr + [1] Documentation/devicetree/bindings/media/video-interfaces.txt Example: @@ -92,6 +111,36 @@ dpi: dpi@7e208000 { }; }; +dsi1: dsi@7e700000 { + compatible = "brcm,bcm2835-dsi1"; + reg = <0x7e700000 0x8c>; + interrupts = <2 12>; + #address-cells = <1>; + #size-cells = <0>; + #clock-cells = <1>; + + clocks = <&clocks BCM2835_PLLD_DSI1>, + <&clocks BCM2835_CLOCK_DSI1E>, + <&clocks BCM2835_CLOCK_DSI1P>; + clock-names = "phy", "escape", "pixel"; + + clock-output-names = "dsi1_byte", "dsi1_ddr2", "dsi1_ddr"; + + pitouchscreen: panel@0 { + compatible = "raspberrypi,touchscreen"; + reg = <0>; + + <...> + }; +}; + +vec: vec@7e806000 { + compatible = "brcm,bcm2835-vec"; + reg = <0x7e806000 0x1000>; + clocks = <&clocks BCM2835_CLOCK_VEC>; + interrupts = <2 27>; +}; + v3d: v3d@7ec00000 { compatible = "brcm,bcm2835-v3d"; reg = <0x7ec00000 0x1000>; diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt index 6532a59c9b43..00ea670b8c4d 100644 --- a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt +++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt @@ -38,10 +38,22 @@ The following input format properties are required except in "rgb 1x" and - adi,input-justification: The input bit justification ("left", "evenly", "right"). +- avdd-supply: A 1.8V supply that powers up the AVDD pin on the chip. +- dvdd-supply: A 1.8V supply that powers up the DVDD pin on the chip. +- pvdd-supply: A 1.8V supply that powers up the PVDD pin on the chip. +- dvdd-3v-supply: A 3.3V supply that powers up the pin called DVDD_3V + on the chip. +- bgvdd-supply: A 1.8V supply that powers up the BGVDD pin. This is + needed only for ADV7511. + The following properties are required for ADV7533: - adi,dsi-lanes: Number of DSI data lanes connected to the DSI host. It should be one of 1, 2, 3 or 4. +- a2vdd-supply: 1.8V supply that powers up the A2VDD pin on the chip. +- v3p3-supply: A 3.3V supply that powers up the V3P3 pin on the chip. +- v1p2-supply: A supply that powers up the V1P2 pin on the chip. It can be + either 1.2V or 1.8V. Optional properties: diff --git a/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt b/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt index 4a0f4f7682ad..0c7473dd0e51 100644 --- a/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt +++ b/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt @@ -33,7 +33,7 @@ Optional properties for dp-controller: in Documentation/devicetree/bindings/media/video-interfaces.txt, please refer to the SoC specific binding document: * Documentation/devicetree/bindings/display/exynos/exynos_dp.txt - * Documentation/devicetree/bindings/video/analogix_dp-rockchip.txt + * Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt [1]: Documentation/devicetree/bindings/media/video-interfaces.txt ------------------------------------------------------------------------------- diff --git a/Documentation/devicetree/bindings/video/bridge/anx7814.txt b/Documentation/devicetree/bindings/display/bridge/anx7814.txt index b2a22c28c9b3..b2a22c28c9b3 100644 --- a/Documentation/devicetree/bindings/video/bridge/anx7814.txt +++ b/Documentation/devicetree/bindings/display/bridge/anx7814.txt diff --git a/Documentation/devicetree/bindings/display/bridge/dumb-vga-dac.txt b/Documentation/devicetree/bindings/display/bridge/dumb-vga-dac.txt index 003bc246a270..164cbb15f04c 100644 --- a/Documentation/devicetree/bindings/display/bridge/dumb-vga-dac.txt +++ b/Documentation/devicetree/bindings/display/bridge/dumb-vga-dac.txt @@ -16,6 +16,8 @@ graph bindings specified in Documentation/devicetree/bindings/graph.txt. - Video port 0 for RGB input - Video port 1 for VGA output +Optional properties: +- vdd-supply: Power supply for DAC Example ------- diff --git a/Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt b/Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt index dc1452f0d5d8..33bf981fbe33 100644 --- a/Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt +++ b/Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt @@ -1,50 +1,33 @@ -DesignWare HDMI bridge bindings - -Required properties: -- compatible: platform specific such as: - * "snps,dw-hdmi-tx" - * "fsl,imx6q-hdmi" - * "fsl,imx6dl-hdmi" - * "rockchip,rk3288-dw-hdmi" -- reg: Physical base address and length of the controller's registers. -- interrupts: The HDMI interrupt number -- clocks, clock-names : must have the phandles to the HDMI iahb and isfr clocks, - as described in Documentation/devicetree/bindings/clock/clock-bindings.txt, - the clocks are soc specific, the clock-names should be "iahb", "isfr" --port@[X]: SoC specific port nodes with endpoint definitions as defined - in Documentation/devicetree/bindings/media/video-interfaces.txt, - please refer to the SoC specific binding document: - * Documentation/devicetree/bindings/display/imx/hdmi.txt - * Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt - -Optional properties -- reg-io-width: the width of the reg:1,4, default set to 1 if not present -- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing -- clocks, clock-names: phandle to the HDMI CEC clock, name should be "cec" - -Example: - hdmi: hdmi@0120000 { - compatible = "fsl,imx6q-hdmi"; - reg = <0x00120000 0x9000>; - interrupts = <0 115 0x04>; - gpr = <&gpr>; - clocks = <&clks 123>, <&clks 124>; - clock-names = "iahb", "isfr"; - ddc-i2c-bus = <&i2c2>; - - port@0 { - reg = <0>; - - hdmi_mux_0: endpoint { - remote-endpoint = <&ipu1_di0_hdmi>; - }; - }; - - port@1 { - reg = <1>; - - hdmi_mux_1: endpoint { - remote-endpoint = <&ipu1_di1_hdmi>; - }; - }; - }; +Synopsys DesignWare HDMI TX Encoder +=================================== + +This document defines device tree properties for the Synopsys DesignWare HDMI +TX Encoder (DWC HDMI TX). It doesn't constitue a device tree binding +specification by itself but is meant to be referenced by platform-specific +device tree bindings. + +When referenced from platform device tree bindings the properties defined in +this document are defined as follows. The platform device tree bindings are +responsible for defining whether each property is required or optional. + +- reg: Memory mapped base address and length of the DWC HDMI TX registers. + +- reg-io-width: Width of the registers specified by the reg property. The + value is expressed in bytes and must be equal to 1 or 4 if specified. The + register width defaults to 1 if the property is not present. + +- interrupts: Reference to the DWC HDMI TX interrupt. + +- clocks: References to all the clocks specified in the clock-names property + as specified in Documentation/devicetree/bindings/clock/clock-bindings.txt. + +- clock-names: The DWC HDMI TX uses the following clocks. + + - "iahb" is the bus clock for either AHB and APB (mandatory). + - "isfr" is the internal register configuration clock (mandatory). + - "cec" is the HDMI CEC controller main clock (optional). + +- ports: The connectivity of the DWC HDMI TX with the rest of the system is + expressed in using ports as specified in the device graph bindings defined + in Documentation/devicetree/bindings/graph.txt. The numbering of the ports + is platform-specific. diff --git a/Documentation/devicetree/bindings/display/bridge/sil-sii8620.txt b/Documentation/devicetree/bindings/display/bridge/sil-sii8620.txt new file mode 100644 index 000000000000..9409d9c6a260 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/sil-sii8620.txt @@ -0,0 +1,33 @@ +Silicon Image SiI8620 HDMI/MHL bridge bindings + +Required properties: + - compatible: "sil,sii8620" + - reg: i2c address of the bridge + - cvcc10-supply: Digital Core Supply Voltage (1.0V) + - iovcc18-supply: I/O Supply Voltage (1.8V) + - interrupts, interrupt-parent: interrupt specifier of INT pin + - reset-gpios: gpio specifier of RESET pin + - clocks, clock-names: specification and name of "xtal" clock + - video interfaces: Device node can contain video interface port + node for HDMI encoder according to [1]. + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + sii8620@39 { + reg = <0x39>; + compatible = "sil,sii8620"; + cvcc10-supply = <&ldo36_reg>; + iovcc18-supply = <&ldo34_reg>; + interrupt-parent = <&gpf0>; + interrupts = <2 0>; + reset-gpio = <&gpv7 0 0>; + clocks = <&pmu_system_controller 0>; + clock-names = "xtal"; + + port { + mhl_to_hdmi: endpoint { + remote-endpoint = <&hdmi_to_mhl>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/ti/ti,tfp410.txt b/Documentation/devicetree/bindings/display/bridge/ti,tfp410.txt index 2cbe32a3d0bb..54d7e31525ec 100644 --- a/Documentation/devicetree/bindings/display/ti/ti,tfp410.txt +++ b/Documentation/devicetree/bindings/display/bridge/ti,tfp410.txt @@ -6,10 +6,15 @@ Required properties: Optional properties: - powerdown-gpios: power-down gpio +- reg: I2C address. If and only if present the device node + should be placed into the i2c controller node where the + tfp410 i2c is connected to. Required nodes: -- Video port 0 for DPI input -- Video port 1 for DVI output +- Video port 0 for DPI input [1]. +- Video port 1 for DVI output [1]. + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt Example ------- diff --git a/Documentation/devicetree/bindings/display/bridge/ti,ths8135.txt b/Documentation/devicetree/bindings/display/bridge/ti,ths8135.txt new file mode 100644 index 000000000000..6ec1a880ac18 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/ti,ths8135.txt @@ -0,0 +1,46 @@ +THS8135 Video DAC +----------------- + +This is the binding for Texas Instruments THS8135 Video DAC bridge. + +Required properties: + +- compatible: Must be "ti,ths8135" + +Required nodes: + +This device has two video ports. Their connections are modelled using the OF +graph bindings specified in Documentation/devicetree/bindings/graph.txt. + +- Video port 0 for RGB input +- Video port 1 for VGA output + +Example +------- + +vga-bridge { + compatible = "ti,ths8135"; + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + vga_bridge_in: endpoint { + remote-endpoint = <&lcdc_out_vga>; + }; + }; + + port@1 { + reg = <1>; + + vga_bridge_out: endpoint { + remote-endpoint = <&vga_con_in>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt b/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt index e9c65746e2f1..b0e506610400 100644 --- a/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt +++ b/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt @@ -6,7 +6,7 @@ Required properties: location and size of the framebuffer memory. - clocks : phandle + clock specifier pair of the FB reference clock. - display : phandle to a display node as described in - Documentation/devicetree/bindings/display/display-timing.txt. + Documentation/devicetree/bindings/display/panel/display-timing.txt. Additionally, the display node has to define properties: - bits-per-pixel: Bits per pixel. - ac-prescale : LCD AC bias frequency. This frequency is the required diff --git a/Documentation/devicetree/bindings/display/exynos/exynos7-decon.txt b/Documentation/devicetree/bindings/display/exynos/exynos7-decon.txt index 3938caacf11c..9e2e7f6f7609 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos7-decon.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos7-decon.txt @@ -33,12 +33,12 @@ Required properties: - i80-if-timings: timing configuration for lcd i80 interface support. Optional Properties: -- samsung,power-domain: a phandle to DECON power domain node. +- power-domains: a phandle to DECON power domain node. - display-timings: timing settings for DECON, as described in document [1]. Can be used in case timings cannot be provided otherwise or to override timings provided by the panel. -[1]: Documentation/devicetree/bindings/display/display-timing.txt +[1]: Documentation/devicetree/bindings/display/panel/display-timing.txt Example: diff --git a/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt b/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt index c7c6b9af87ac..18645e0228b0 100644 --- a/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt +++ b/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt @@ -83,7 +83,7 @@ in [2]. The following are properties specific to those nodes: 3 - for parallel output, 4 - for write-back interface -[1]: Documentation/devicetree/bindings/display/display-timing.txt +[1]: Documentation/devicetree/bindings/display/panel/display-timing.txt [2]: Documentation/devicetree/bindings/media/video-interfaces.txt Example: diff --git a/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt b/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt index 38dc9d60eef8..305a0e72a900 100644 --- a/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt +++ b/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt @@ -16,7 +16,7 @@ Required properties: "clk_ade_core" for the ADE core clock. "clk_codec_jpeg" for the media NOC QoS clock, which use the same clock with jpeg codec. - "clk_ade_pix" for the ADE pixel clok. + "clk_ade_pix" for the ADE pixel clock. - assigned-clocks: Should contain "clk_ade_core" and "clk_codec_jpeg" clocks' phandle + clock-specifier pairs. - assigned-clock-rates: clock rates, one for each entry in assigned-clocks. diff --git a/Documentation/devicetree/bindings/display/ht16k33.txt b/Documentation/devicetree/bindings/display/ht16k33.txt new file mode 100644 index 000000000000..8e5b30b87754 --- /dev/null +++ b/Documentation/devicetree/bindings/display/ht16k33.txt @@ -0,0 +1,42 @@ +Holtek ht16k33 RAM mapping 16*8 LED controller driver with keyscan +------------------------------------------------------------------------------- + +Required properties: +- compatible: "holtek,ht16k33" +- reg: I2C slave address of the chip. +- interrupt-parent: A phandle pointing to the interrupt controller + serving the interrupt for this chip. +- interrupts: Interrupt specification for the key pressed interrupt. +- refresh-rate-hz: Display update interval in HZ. +- debounce-delay-ms: Debouncing interval time in milliseconds. +- linux,keymap: The keymap for keys as described in the binding + document (devicetree/bindings/input/matrix-keymap.txt). + +Optional properties: +- linux,no-autorepeat: Disable keyrepeat. +- default-brightness-level: Initial brightness level [0-15] (default: 15). + +Example: + +&i2c1 { + ht16k33: ht16k33@70 { + compatible = "holtek,ht16k33"; + reg = <0x70>; + refresh-rate-hz = <20>; + debounce-delay-ms = <50>; + interrupt-parent = <&gpio4>; + interrupts = <5 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>; + linux,keymap = < + MATRIX_KEY(2, 0, KEY_F6) + MATRIX_KEY(3, 0, KEY_F8) + MATRIX_KEY(4, 0, KEY_F10) + MATRIX_KEY(5, 0, KEY_F4) + MATRIX_KEY(6, 0, KEY_F2) + MATRIX_KEY(2, 1, KEY_F5) + MATRIX_KEY(3, 1, KEY_F7) + MATRIX_KEY(4, 1, KEY_F9) + MATRIX_KEY(5, 1, KEY_F3) + MATRIX_KEY(6, 1, KEY_F1) + >; + }; +}; diff --git a/Documentation/devicetree/bindings/display/imx/fsl,imx-fb.txt b/Documentation/devicetree/bindings/display/imx/fsl,imx-fb.txt index 00d5f8ea7ec6..7a5c0e204c8e 100644 --- a/Documentation/devicetree/bindings/display/imx/fsl,imx-fb.txt +++ b/Documentation/devicetree/bindings/display/imx/fsl,imx-fb.txt @@ -9,7 +9,7 @@ Required properties: Required nodes: - display: Phandle to a display node as described in - Documentation/devicetree/bindings/display/display-timing.txt + Documentation/devicetree/bindings/display/panel/display-timing.txt Additional, the display node has to define properties: - bits-per-pixel: Bits per pixel - fsl,pcr: LCDC PCR value diff --git a/Documentation/devicetree/bindings/display/imx/hdmi.txt b/Documentation/devicetree/bindings/display/imx/hdmi.txt index 1b756cf9afb0..66a8f86e5d12 100644 --- a/Documentation/devicetree/bindings/display/imx/hdmi.txt +++ b/Documentation/devicetree/bindings/display/imx/hdmi.txt @@ -1,29 +1,36 @@ -Device-Tree bindings for HDMI Transmitter +Freescale i.MX6 DWC HDMI TX Encoder +=================================== -HDMI Transmitter -================ +The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP +with a companion PHY IP. + +These DT bindings follow the Synopsys DWC HDMI TX bindings defined in +Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt with the +following device-specific properties. -The HDMI Transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP -with accompanying PHY IP. Required properties: - - #address-cells : should be <1> - - #size-cells : should be <0> - - compatible : should be "fsl,imx6q-hdmi" or "fsl,imx6dl-hdmi". - - gpr : should be <&gpr>. - The phandle points to the iomuxc-gpr region containing the HDMI - multiplexer control register. - - clocks, clock-names : phandles to the HDMI iahb and isrf clocks, as described - in Documentation/devicetree/bindings/clock/clock-bindings.txt and - Documentation/devicetree/bindings/clock/imx6q-clock.txt. - - port@[0-4]: Up to four port nodes with endpoint definitions as defined in - Documentation/devicetree/bindings/media/video-interfaces.txt, - corresponding to the four inputs to the HDMI multiplexer. - -Optional properties: - - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing - -example: + +- compatible : Shall be one of "fsl,imx6q-hdmi" or "fsl,imx6dl-hdmi". +- reg: See dw_hdmi.txt. +- interrupts: HDMI interrupt number +- clocks: See dw_hdmi.txt. +- clock-names: Shall contain "iahb" and "isfr" as defined in dw_hdmi.txt. +- ports: See dw_hdmi.txt. The DWC HDMI shall have between one and four ports, + numbered 0 to 3, corresponding to the four inputs of the HDMI multiplexer. + Each port shall have a single endpoint. +- gpr : Shall contain a phandle to the iomuxc-gpr region containing the HDMI + multiplexer control register. + +Optional properties + +- ddc-i2c-bus: The HDMI DDC bus can be connected to either a system I2C master + or the functionally-reduced I2C master contained in the DWC HDMI. When + connected to a system I2C master this property contains a phandle to that + I2C master controller. + + +Example: gpr: iomuxc-gpr@020e0000 { /* ... */ diff --git a/Documentation/devicetree/bindings/display/imx/ldb.txt b/Documentation/devicetree/bindings/display/imx/ldb.txt index a407462c885e..38c637fa39dd 100644 --- a/Documentation/devicetree/bindings/display/imx/ldb.txt +++ b/Documentation/devicetree/bindings/display/imx/ldb.txt @@ -64,7 +64,7 @@ Required properties: Optional properties (required if display-timings are used): - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing - display-timings : A node that describes the display timings as defined in - Documentation/devicetree/bindings/display/display-timing.txt. + Documentation/devicetree/bindings/display/panel/display-timing.txt. - fsl,data-mapping : should be "spwg" or "jeida" This describes how the color bits are laid out in the serialized LVDS signal. diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt index db6e77edbea8..708f5664a316 100644 --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt @@ -55,7 +55,7 @@ Required properties (DMA function blocks): "mediatek,<chip>-disp-rdma" "mediatek,<chip>-disp-wdma" - larb: Should contain a phandle pointing to the local arbiter device as defined - in Documentation/devicetree/bindings/soc/mediatek/mediatek,smi-larb.txt + in Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt - iommus: Should point to the respective IOMMU block with master port as argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.txt for details. diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt b/Documentation/devicetree/bindings/display/msm/dsi.txt index 6b1cab17f52d..fa00e62e1cf6 100644 --- a/Documentation/devicetree/bindings/display/msm/dsi.txt +++ b/Documentation/devicetree/bindings/display/msm/dsi.txt @@ -108,7 +108,7 @@ Optional properties: - qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY regulator is wanted. -[1] Documentation/devicetree/bindings/clocks/clock-bindings.txt +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt [2] Documentation/devicetree/bindings/graph.txt [3] Documentation/devicetree/bindings/media/video-interfaces.txt [4] Documentation/devicetree/bindings/display/panel/ diff --git a/Documentation/devicetree/bindings/display/msm/edp.txt b/Documentation/devicetree/bindings/display/msm/edp.txt index 3a20f6ea5898..e63032be5401 100644 --- a/Documentation/devicetree/bindings/display/msm/edp.txt +++ b/Documentation/devicetree/bindings/display/msm/edp.txt @@ -10,7 +10,7 @@ Required properties: - interrupts: The interrupt signal from the eDP block. - power-domains: Should be <&mmcc MDSS_GDSC>. - clocks: device clocks - See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details. + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. - clock-names: the following clocks are required: * "core_clk" * "iface_clk" diff --git a/Documentation/devicetree/bindings/display/msm/gpu.txt b/Documentation/devicetree/bindings/display/msm/gpu.txt index 67d0a58dbb77..43fac0fe09bb 100644 --- a/Documentation/devicetree/bindings/display/msm/gpu.txt +++ b/Documentation/devicetree/bindings/display/msm/gpu.txt @@ -1,23 +1,19 @@ Qualcomm adreno/snapdragon GPU Required properties: -- compatible: "qcom,adreno-3xx" +- compatible: "qcom,adreno-XYZ.W", "qcom,adreno" + for example: "qcom,adreno-306.0", "qcom,adreno" + Note that you need to list the less specific "qcom,adreno" (since this + is what the device is matched on), in addition to the more specific + with the chip-id. - reg: Physical base address and length of the controller's registers. - interrupts: The interrupt signal from the gpu. - clocks: device clocks See ../clocks/clock-bindings.txt for details. - clock-names: the following clocks are required: - * "core_clk" - * "iface_clk" - * "mem_iface_clk" -- qcom,chipid: gpu chip-id. Note this may become optional for future - devices if we can reliably read the chipid from hw -- qcom,gpu-pwrlevels: list of operating points - - compatible: "qcom,gpu-pwrlevels" - - for each qcom,gpu-pwrlevel: - - qcom,gpu-freq: requested gpu clock speed - - NOTE: downstream android driver defines additional parameters to - configure memory bandwidth scaling per OPP. + * "core" + * "iface" + * "mem_iface" Example: @@ -25,28 +21,18 @@ Example: ... gpu: qcom,kgsl-3d0@4300000 { - compatible = "qcom,adreno-3xx"; + compatible = "qcom,adreno-320.2", "qcom,adreno"; reg = <0x04300000 0x20000>; reg-names = "kgsl_3d0_reg_memory"; interrupts = <GIC_SPI 80 0>; interrupt-names = "kgsl_3d0_irq"; clock-names = - "core_clk", - "iface_clk", - "mem_iface_clk"; + "core", + "iface", + "mem_iface"; clocks = <&mmcc GFX3D_CLK>, <&mmcc GFX3D_AHB_CLK>, <&mmcc MMSS_IMEM_AHB_CLK>; - qcom,chipid = <0x03020100>; - qcom,gpu-pwrlevels { - compatible = "qcom,gpu-pwrlevels"; - qcom,gpu-pwrlevel@0 { - qcom,gpu-freq = <450000000>; - }; - qcom,gpu-pwrlevel@1 { - qcom,gpu-freq = <27000000>; - }; - }; }; }; diff --git a/Documentation/devicetree/bindings/display/msm/hdmi.txt b/Documentation/devicetree/bindings/display/msm/hdmi.txt index 2ad578984fcf..2d306f402d18 100644 --- a/Documentation/devicetree/bindings/display/msm/hdmi.txt +++ b/Documentation/devicetree/bindings/display/msm/hdmi.txt @@ -49,7 +49,7 @@ Required properties: * "hdmi_tx_l4" - power-domains: Should be <&mmcc MDSS_GDSC>. - clocks: device clocks - See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details. + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. - core-vdda-supply: phandle to vdda regulator device node Example: diff --git a/Documentation/devicetree/bindings/display/multi-inno,mi0283qt.txt b/Documentation/devicetree/bindings/display/multi-inno,mi0283qt.txt new file mode 100644 index 000000000000..eed48c3d4875 --- /dev/null +++ b/Documentation/devicetree/bindings/display/multi-inno,mi0283qt.txt @@ -0,0 +1,27 @@ +Multi-Inno MI0283QT display panel + +Required properties: +- compatible: "multi-inno,mi0283qt". + +The node for this driver must be a child node of a SPI controller, hence +all mandatory properties described in ../spi/spi-bus.txt must be specified. + +Optional properties: +- dc-gpios: D/C pin. The presence/absence of this GPIO determines + the panel interface mode (IM[3:0] pins): + - present: IM=x110 4-wire 8-bit data serial interface + - absent: IM=x101 3-wire 9-bit data serial interface +- reset-gpios: Reset pin +- power-supply: A regulator node for the supply voltage. +- backlight: phandle of the backlight device attached to the panel +- rotation: panel rotation in degrees counter clockwise (0,90,180,270) + +Example: + mi0283qt@0{ + compatible = "multi-inno,mi0283qt"; + reg = <0>; + spi-max-frequency = <32000000>; + rotation = <90>; + dc-gpios = <&gpio 25 0>; + backlight = <&backlight>; + }; diff --git a/Documentation/devicetree/bindings/display/mxsfb.txt b/Documentation/devicetree/bindings/display/mxsfb.txt index 96ec5179c8a0..472e1ea6c591 100644 --- a/Documentation/devicetree/bindings/display/mxsfb.txt +++ b/Documentation/devicetree/bindings/display/mxsfb.txt @@ -1,20 +1,57 @@ * Freescale MXS LCD Interface (LCDIF) +New bindings: +============= Required properties: -- compatible: Should be "fsl,<chip>-lcdif". Supported chips include - imx23 and imx28. -- reg: Address and length of the register set for lcdif -- interrupts: Should contain lcdif interrupts -- display : phandle to display node (see below for details) +- compatible: Should be "fsl,imx23-lcdif" for i.MX23. + Should be "fsl,imx28-lcdif" for i.MX28. + Should be "fsl,imx6sx-lcdif" for i.MX6SX. +- reg: Address and length of the register set for LCDIF +- interrupts: Should contain LCDIF interrupt +- clocks: A list of phandle + clock-specifier pairs, one for each + entry in 'clock-names'. +- clock-names: A list of clock names. For MXSFB it should contain: + - "pix" for the LCDIF block clock + - (MX6SX-only) "axi", "disp_axi" for the bus interface clock + +Required sub-nodes: + - port: The connection to an encoder chip. + +Example: + + lcdif1: display-controller@2220000 { + compatible = "fsl,imx6sx-lcdif", "fsl,imx28-lcdif"; + reg = <0x02220000 0x4000>; + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6SX_CLK_LCDIF1_PIX>, + <&clks IMX6SX_CLK_LCDIF_APB>, + <&clks IMX6SX_CLK_DISPLAY_AXI>; + clock-names = "pix", "axi", "disp_axi"; + + port { + parallel_out: endpoint { + remote-endpoint = <&panel_in_parallel>; + }; + }; + }; + +Deprecated bindings: +==================== +Required properties: +- compatible: Should be "fsl,imx23-lcdif" for i.MX23. + Should be "fsl,imx28-lcdif" for i.MX28. +- reg: Address and length of the register set for LCDIF +- interrupts: Should contain LCDIF interrupts +- display: phandle to display node (see below for details) * display node Required properties: -- bits-per-pixel : <16> for RGB565, <32> for RGB888/666. -- bus-width : number of data lines. Could be <8>, <16>, <18> or <24>. +- bits-per-pixel: <16> for RGB565, <32> for RGB888/666. +- bus-width: number of data lines. Could be <8>, <16>, <18> or <24>. Required sub-node: -- display-timings : Refer to binding doc display-timing.txt for details. +- display-timings: Refer to binding doc display-timing.txt for details. Examples: diff --git a/Documentation/devicetree/bindings/display/panel/auo,g133han01.txt b/Documentation/devicetree/bindings/display/panel/auo,g133han01.txt new file mode 100644 index 000000000000..3afc76747824 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/auo,g133han01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 13.3" FHD (1920x1080) TFT LCD panel + +Required properties: +- compatible: should be "auo,g133han01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/auo,g185han01.txt b/Documentation/devicetree/bindings/display/panel/auo,g185han01.txt new file mode 100644 index 000000000000..ed657c2141d4 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/auo,g185han01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 18.5" FHD (1920x1080) TFT LCD panel + +Required properties: +- compatible: should be "auo,g185han01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/auo,t215hvn01.txt b/Documentation/devicetree/bindings/display/panel/auo,t215hvn01.txt new file mode 100644 index 000000000000..cbd9da3f03b1 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/auo,t215hvn01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 21.5" FHD (1920x1080) color TFT LCD panel + +Required properties: +- compatible: should be "auo,t215hvn01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/boe,nv101wxmn51.txt b/Documentation/devicetree/bindings/display/panel/boe,nv101wxmn51.txt new file mode 100644 index 000000000000..b258d6a91ec6 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/boe,nv101wxmn51.txt @@ -0,0 +1,7 @@ +BOE OPTOELECTRONICS TECHNOLOGY 10.1" WXGA TFT LCD panel + +Required properties: +- compatible: should be "boe,nv101wxmn51" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/chunghwa,claa070wp03xg.txt b/Documentation/devicetree/bindings/display/panel/chunghwa,claa070wp03xg.txt new file mode 100644 index 000000000000..dd22685d2adc --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/chunghwa,claa070wp03xg.txt @@ -0,0 +1,7 @@ +Chunghwa Picture Tubes Ltd. 7" WXGA TFT LCD panel + +Required properties: +- compatible: should be "chunghwa,claa070wp03xg" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/display-timing.txt b/Documentation/devicetree/bindings/display/panel/display-timing.txt index e1d4a0b59612..81a75893d1b8 100644 --- a/Documentation/devicetree/bindings/display/panel/display-timing.txt +++ b/Documentation/devicetree/bindings/display/panel/display-timing.txt @@ -32,6 +32,14 @@ optional properties: - active low = drive pixel data on falling edge/ sample data on rising edge - ignored = ignored + - syncclk-active: with + - active high = drive sync on rising edge/ + sample sync on falling edge of pixel + clock + - active low = drive sync on falling edge/ + sample sync on rising edge of pixel + clock + - omitted = same configuration as pixelclk-active - interlaced (bool): boolean to enable interlaced mode - doublescan (bool): boolean to enable doublescan mode - doubleclk (bool): boolean to enable doubleclock mode diff --git a/Documentation/devicetree/bindings/display/panel/netron-dy,e231732.txt b/Documentation/devicetree/bindings/display/panel/netron-dy,e231732.txt new file mode 100644 index 000000000000..c6d06b5eab51 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/netron-dy,e231732.txt @@ -0,0 +1,7 @@ +Netron-DY E231732 7.0" WSVGA TFT LCD panel + +Required properties: +- compatible: should be "netron-dy,e231732" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/nvd,9128.txt b/Documentation/devicetree/bindings/display/panel/nvd,9128.txt new file mode 100644 index 000000000000..17bcd017c678 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/nvd,9128.txt @@ -0,0 +1,7 @@ +New Vision Display 7.0" 800 RGB x 480 TFT LCD panel + +Required properties: +- compatible: should be "nvd,9128" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/panel-dpi.txt b/Documentation/devicetree/bindings/display/panel/panel-dpi.txt index b52ac52757df..d4add13e592d 100644 --- a/Documentation/devicetree/bindings/display/panel/panel-dpi.txt +++ b/Documentation/devicetree/bindings/display/panel/panel-dpi.txt @@ -12,7 +12,7 @@ Optional properties: Required nodes: - "panel-timing" containing video timings - (Documentation/devicetree/bindings/display/display-timing.txt) + (Documentation/devicetree/bindings/display/panel/display-timing.txt) - Video port for DPI input Example diff --git a/Documentation/devicetree/bindings/display/panel/panel.txt b/Documentation/devicetree/bindings/display/panel/panel.txt new file mode 100644 index 000000000000..e2e6867852b8 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/panel.txt @@ -0,0 +1,4 @@ +Common display properties +------------------------- + +- rotation: Display rotation in degrees counter clockwise (0,90,180,270) diff --git a/Documentation/devicetree/bindings/display/panel/samsung,ld9040.txt b/Documentation/devicetree/bindings/display/panel/samsung,ld9040.txt index fc595d9b985b..354d4d1df4ff 100644 --- a/Documentation/devicetree/bindings/display/panel/samsung,ld9040.txt +++ b/Documentation/devicetree/bindings/display/panel/samsung,ld9040.txt @@ -20,7 +20,7 @@ The device node can contain one 'port' child node with one child 'endpoint' node, according to the bindings defined in [3]. This node should describe panel's video bus. -[1]: Documentation/devicetree/bindings/display/display-timing.txt +[1]: Documentation/devicetree/bindings/display/panel/display-timing.txt [2]: Documentation/devicetree/bindings/spi/spi-bus.txt [3]: Documentation/devicetree/bindings/media/video-interfaces.txt diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e8aa0.txt b/Documentation/devicetree/bindings/display/panel/samsung,s6e8aa0.txt index 25701c81b5e0..9e766c5f86da 100644 --- a/Documentation/devicetree/bindings/display/panel/samsung,s6e8aa0.txt +++ b/Documentation/devicetree/bindings/display/panel/samsung,s6e8aa0.txt @@ -21,7 +21,7 @@ The device node can contain one 'port' child node with one child 'endpoint' node, according to the bindings defined in [2]. This node should describe panel's video bus. -[1]: Documentation/devicetree/bindings/display/display-timing.txt +[1]: Documentation/devicetree/bindings/display/panel/display-timing.txt [2]: Documentation/devicetree/bindings/media/video-interfaces.txt Example: diff --git a/Documentation/devicetree/bindings/display/panel/sharp,lq150x1lg11.txt b/Documentation/devicetree/bindings/display/panel/sharp,lq150x1lg11.txt new file mode 100644 index 000000000000..0f57c3143506 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sharp,lq150x1lg11.txt @@ -0,0 +1,36 @@ +Sharp 15" LQ150X1LG11 XGA TFT LCD panel + +Required properties: +- compatible: should be "sharp,lq150x1lg11" +- power-supply: regulator to provide the VCC supply voltage (3.3 volts) + +Optional properties: +- backlight: phandle of the backlight device +- rlud-gpios: a single GPIO for the RL/UD (rotate 180 degrees) pin. +- sellvds-gpios: a single GPIO for the SELLVDS pin. + +If rlud-gpios and/or sellvds-gpios are not specified, the RL/UD and/or SELLVDS +pins are assumed to be handled appropriately by the hardware. + +Example: + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 100000>; /* VBR */ + + brightness-levels = <0 20 40 60 80 100>; + default-brightness-level = <2>; + + power-supply = <&vdd_12v_reg>; /* VDD */ + enable-gpios = <&gpio 42 GPIO_ACTIVE_HIGH>; /* XSTABY */ + }; + + panel { + compatible = "sharp,lq150x1lg11"; + + power-supply = <&vcc_3v3_reg>; /* VCC */ + + backlight = <&backlight>; + rlud-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; /* RL/UD */ + sellvds-gpios = <&gpio 18 GPIO_ACTIVE_HIGH>; /* SELLVDS */ + }; diff --git a/Documentation/devicetree/bindings/display/panel/tianma,tm070jdhg30.txt b/Documentation/devicetree/bindings/display/panel/tianma,tm070jdhg30.txt new file mode 100644 index 000000000000..eb9501a82e25 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/tianma,tm070jdhg30.txt @@ -0,0 +1,7 @@ +Tianma Micro-electronics TM070JDHG30 7.0" WXGA TFT LCD panel + +Required properties: +- compatible: should be "tianma,tm070jdhg30" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/renesas,du.txt b/Documentation/devicetree/bindings/display/renesas,du.txt index 0d30e42e40be..1a02f099a0ff 100644 --- a/Documentation/devicetree/bindings/display/renesas,du.txt +++ b/Documentation/devicetree/bindings/display/renesas,du.txt @@ -6,9 +6,11 @@ Required Properties: - "renesas,du-r8a7779" for R8A7779 (R-Car H1) compatible DU - "renesas,du-r8a7790" for R8A7790 (R-Car H2) compatible DU - "renesas,du-r8a7791" for R8A7791 (R-Car M2-W) compatible DU + - "renesas,du-r8a7792" for R8A7792 (R-Car V2H) compatible DU - "renesas,du-r8a7793" for R8A7793 (R-Car M2-N) compatible DU - "renesas,du-r8a7794" for R8A7794 (R-Car E2) compatible DU - "renesas,du-r8a7795" for R8A7795 (R-Car H3) compatible DU + - "renesas,du-r8a7796" for R8A7796 (R-Car M3-W) compatible DU - reg: A list of base address and length of each memory resource, one for each entry in the reg-names property. @@ -25,10 +27,10 @@ Required Properties: - clock-names: Name of the clocks. This property is model-dependent. - R8A7779 uses a single functional clock. The clock doesn't need to be named. - - R8A779[01345] use one functional clock per channel and one clock per LVDS - encoder (if available). The functional clocks must be named "du.x" with - "x" being the channel numerical index. The LVDS clocks must be named - "lvds.x" with "x" being the LVDS encoder numerical index. + - R8A779[0123456] use one functional clock per channel and one clock per + LVDS encoder (if available). The functional clocks must be named "du.x" + with "x" being the channel numerical index. The LVDS clocks must be + named "lvds.x" with "x" being the LVDS encoder numerical index. - In addition to the functional and encoder clocks, all DU versions also support externally supplied pixel clocks. Those clocks are optional. When supplied they must be named "dclkin.x" with "x" being the input @@ -47,9 +49,11 @@ corresponding to each DU output. R8A7779 (H1) DPAD 0 DPAD 1 - - R8A7790 (H2) DPAD LVDS 0 LVDS 1 - R8A7791 (M2-W) DPAD LVDS 0 - - + R8A7792 (V2H) DPAD 0 DPAD 1 - - R8A7793 (M2-N) DPAD LVDS 0 - - R8A7794 (E2) DPAD 0 DPAD 1 - - R8A7795 (H3) DPAD HDMI 0 HDMI 1 LVDS + R8A7796 (M3-W) DPAD HDMI LVDS - Example: R8A7790 (R-Car H2) DU diff --git a/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt index 01cced1c2a18..47665a12786f 100644 --- a/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt +++ b/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt @@ -35,7 +35,7 @@ Optional property for different chips: Required elements: "grf" For the below properties, please refer to Analogix DP binding document: - * Documentation/devicetree/bindings/drm/bridge/analogix_dp.txt + * Documentation/devicetree/bindings/display/bridge/analogix_dp.txt - phys (required) - phy-names (required) - hpd-gpios (optional) diff --git a/Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt index 668091f27674..046076c6b277 100644 --- a/Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt +++ b/Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt @@ -1,24 +1,39 @@ -Rockchip specific extensions to the Synopsys Designware HDMI -================================ +Rockchip DWC HDMI TX Encoder +============================ + +The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP +with a companion PHY IP. + +These DT bindings follow the Synopsys DWC HDMI TX bindings defined in +Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt with the +following device-specific properties. + Required properties: -- compatible: "rockchip,rk3288-dw-hdmi"; -- reg: Physical base address and length of the controller's registers. -- clocks: phandle to hdmi iahb and isfr clocks. -- clock-names: should be "iahb" "isfr" -- rockchip,grf: this soc should set GRF regs to mux vopl/vopb. + +- compatible: Shall contain "rockchip,rk3288-dw-hdmi". +- reg: See dw_hdmi.txt. +- reg-io-width: See dw_hdmi.txt. Shall be 4. - interrupts: HDMI interrupt number -- ports: contain a port node with endpoint definitions as defined in - Documentation/devicetree/bindings/media/video-interfaces.txt. For - vopb,set the reg = <0> and set the reg = <1> for vopl. -- reg-io-width: the width of the reg:1,4, the value should be 4 on - rk3288 platform +- clocks: See dw_hdmi.txt. +- clock-names: Shall contain "iahb" and "isfr" as defined in dw_hdmi.txt. +- ports: See dw_hdmi.txt. The DWC HDMI shall have a single port numbered 0 + corresponding to the video input of the controller. The port shall have two + endpoints, numbered 0 and 1, connected respectively to the vopb and vopl. +- rockchip,grf: Shall reference the GRF to mux vopl/vopb. Optional properties -- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing -- clocks, clock-names: phandle to the HDMI CEC clock, name should be "cec" + +- ddc-i2c-bus: The HDMI DDC bus can be connected to either a system I2C master + or the functionally-reduced I2C master contained in the DWC HDMI. When + connected to a system I2C master this property contains a phandle to that + I2C master controller. +- clock-names: See dw_hdmi.txt. The "cec" clock is optional. +- clock-names: May contain "cec" as defined in dw_hdmi.txt. + Example: + hdmi: hdmi@ff980000 { compatible = "rockchip,rk3288-dw-hdmi"; reg = <0xff980000 0x20000>; diff --git a/Documentation/devicetree/bindings/display/ssd1307fb.txt b/Documentation/devicetree/bindings/display/ssd1307fb.txt index eb31ed47a283..209d931ef16c 100644 --- a/Documentation/devicetree/bindings/display/ssd1307fb.txt +++ b/Documentation/devicetree/bindings/display/ssd1307fb.txt @@ -8,14 +8,15 @@ Required properties: 0x3c or 0x3d - pwm: Should contain the pwm to use according to the OF device tree PWM specification [0]. Only required for the ssd1307. - - reset-gpios: Should contain the GPIO used to reset the OLED display - solomon,height: Height in pixel of the screen driven by the controller - solomon,width: Width in pixel of the screen driven by the controller - solomon,page-offset: Offset of pages (band of 8 pixels) that the screen is mapped to. Optional properties: - - reset-active-low: Is the reset gpio is active on physical low? + - reset-gpios: The GPIO used to reset the OLED display, if available. See + Documentation/devicetree/bindings/gpio/gpio.txt for details. + - vbat-supply: The supply for VBAT - solomon,segment-no-remap: Display needs normal (non-inverted) data column to segment mapping - solomon,com-seq: Display uses sequential COM pin configuration diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt index b95696d748c7..b82c00449468 100644 --- a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt @@ -28,6 +28,8 @@ The TCON acts as a timing controller for RGB, LVDS and TV interfaces. Required properties: - compatible: value must be either: * allwinner,sun5i-a13-tcon + * allwinner,sun6i-a31-tcon + * allwinner,sun6i-a31s-tcon * allwinner,sun8i-a33-tcon - reg: base address and size of memory-mapped region - interrupts: interrupt associated to this IP @@ -50,7 +52,7 @@ Required properties: second the block connected to the TCON channel 1 (usually the TV encoder) -On the A13, there is one more clock required: +On SoCs other than the A33, there is one more clock required: - 'tcon-ch1': The clock driving the TCON channel 1 DRC @@ -64,6 +66,8 @@ adaptive backlight control. Required properties: - compatible: value must be one of: + * allwinner,sun6i-a31-drc + * allwinner,sun6i-a31s-drc * allwinner,sun8i-a33-drc - reg: base address and size of the memory-mapped region. - interrupts: interrupt associated to this IP @@ -87,6 +91,7 @@ system. Required properties: - compatible: value must be one of: * allwinner,sun5i-a13-display-backend + * allwinner,sun6i-a31-display-backend * allwinner,sun8i-a33-display-backend - reg: base address and size of the memory-mapped region. - clocks: phandles to the clocks feeding the frontend and backend @@ -117,6 +122,7 @@ deinterlacing and color space conversion. Required properties: - compatible: value must be one of: * allwinner,sun5i-a13-display-frontend + * allwinner,sun6i-a31-display-frontend * allwinner,sun8i-a33-display-frontend - reg: base address and size of the memory-mapped region. - interrupts: interrupt associated to this IP @@ -142,6 +148,8 @@ extra node. Required properties: - compatible: value must be one of: * allwinner,sun5i-a13-display-engine + * allwinner,sun6i-a31-display-engine + * allwinner,sun6i-a31s-display-engine * allwinner,sun8i-a33-display-engine - allwinner,pipelines: list of phandle to the display engine diff --git a/Documentation/devicetree/bindings/display/tilcdc/panel.txt b/Documentation/devicetree/bindings/display/tilcdc/panel.txt index f20b31cdc59a..808216310ea2 100644 --- a/Documentation/devicetree/bindings/display/tilcdc/panel.txt +++ b/Documentation/devicetree/bindings/display/tilcdc/panel.txt @@ -15,7 +15,7 @@ Required properties: - display-timings: typical videomode of lcd panel. Multiple video modes can be listed if the panel supports multiple timings, but the 'native-mode' should be the preferred/default resolution. Refer to - Documentation/devicetree/bindings/display/display-timing.txt for display + Documentation/devicetree/bindings/display/panel/display-timing.txt for display timing binding details. Optional properties: diff --git a/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt b/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt index a83abd79c55c..6fddb4f4f71a 100644 --- a/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt +++ b/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt @@ -1,7 +1,9 @@ Device-Tree bindings for tilcdc DRM driver Required properties: - - compatible: value should be "ti,am33xx-tilcdc". + - compatible: value should be one of the following: + - "ti,am33xx-tilcdc" for AM335x based boards + - "ti,da850-tilcdc" for DA850/AM18x/OMAP-L138 based boards - interrupts: the interrupt number - reg: base address and size of the LCDC device @@ -51,7 +53,7 @@ Optional nodes: Example: fb: fb@4830e000 { - compatible = "ti,am33xx-tilcdc"; + compatible = "ti,am33xx-tilcdc", "ti,da850-tilcdc"; reg = <0x4830e000 0x1000>; interrupt-parent = <&intc>; interrupts = <36>; diff --git a/Documentation/devicetree/bindings/display/zte,vou.txt b/Documentation/devicetree/bindings/display/zte,vou.txt new file mode 100644 index 000000000000..9c356284232b --- /dev/null +++ b/Documentation/devicetree/bindings/display/zte,vou.txt @@ -0,0 +1,99 @@ +ZTE VOU Display Controller + +This is a display controller found on ZTE ZX296718 SoC. It includes multiple +Graphic Layer (GL) and Video Layer (VL), two Mixers/Channels, and a few blocks +handling scaling, color space conversion etc. VOU also integrates the support +for typical output devices, like HDMI, TV Encoder, VGA, and RGB LCD. + +* Master VOU node + +It must be the parent node of all the sub-device nodes. + +Required properties: + - compatible: should be "zte,zx296718-vou" + - #address-cells: should be <1> + - #size-cells: should be <1> + - ranges: list of address translations between VOU and sub-devices + +* VOU DPC device + +Required properties: + - compatible: should be "zte,zx296718-dpc" + - reg: Physical base address and length of DPC register regions, one for each + entry in 'reg-names' + - reg-names: The names of register regions. The following regions are required: + "osd" + "timing_ctrl" + "dtrc" + "vou_ctrl" + "otfppu" + - interrupts: VOU DPC interrupt number to CPU + - clocks: A list of phandle + clock-specifier pairs, one for each entry + in 'clock-names' + - clock-names: A list of clock names. The following clocks are required: + "aclk" + "ppu_wclk" + "main_wclk" + "aux_wclk" + +* HDMI output device + +Required properties: + - compatible: should be "zte,zx296718-hdmi" + - reg: Physical base address and length of the HDMI device IO region + - interrupts : HDMI interrupt number to CPU + - clocks: A list of phandle + clock-specifier pairs, one for each entry + in 'clock-names' + - clock-names: A list of clock names. The following clocks are required: + "osc_cec" + "osc_clk" + "xclk" + +* TV Encoder output device + +Required properties: + - compatible: should be "zte,zx296718-tvenc" + - reg: Physical base address and length of the TVENC device IO region + - zte,tvenc-power-control: the phandle to SYSCTRL block followed by two + integer cells. The first cell is the offset of SYSCTRL register used + to control TV Encoder DAC power, and the second cell is the bit mask. + +Example: + +vou: vou@1440000 { + compatible = "zte,zx296718-vou"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x1440000 0x10000>; + + dpc: dpc@0 { + compatible = "zte,zx296718-dpc"; + reg = <0x0000 0x1000>, <0x1000 0x1000>, + <0x5000 0x1000>, <0x6000 0x1000>, + <0xa000 0x1000>; + reg-names = "osd", "timing_ctrl", + "dtrc", "vou_ctrl", + "otfppu"; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&topcrm VOU_ACLK>, <&topcrm VOU_PPU_WCLK>, + <&topcrm VOU_MAIN_WCLK>, <&topcrm VOU_AUX_WCLK>; + clock-names = "aclk", "ppu_wclk", + "main_wclk", "aux_wclk"; + }; + + hdmi: hdmi@c000 { + compatible = "zte,zx296718-hdmi"; + reg = <0xc000 0x4000>; + interrupts = <GIC_SPI 82 IRQ_TYPE_EDGE_RISING>; + clocks = <&topcrm HDMI_OSC_CEC>, + <&topcrm HDMI_OSC_CLK>, + <&topcrm HDMI_XCLK>; + clock-names = "osc_cec", "osc_clk", "xclk"; + }; + + tvenc: tvenc@2000 { + compatible = "zte,zx296718-tvenc"; + reg = <0x2000 0x1000>; + zte,tvenc-power-control = <&sysctrl 0x170 0x10>; + }; +}; diff --git a/Documentation/devicetree/bindings/dma/nbpfaxi.txt b/Documentation/devicetree/bindings/dma/nbpfaxi.txt index d5e2522b9ec1..d2e1e62e346a 100644 --- a/Documentation/devicetree/bindings/dma/nbpfaxi.txt +++ b/Documentation/devicetree/bindings/dma/nbpfaxi.txt @@ -23,6 +23,14 @@ Required properties #define NBPF_SLAVE_RQ_LEVEL 4 Optional properties: +- max-burst-mem-read: limit burst size for memory reads + (DMA_MEM_TO_MEM/DMA_MEM_TO_DEV) to this value, specified in bytes, rather + than using the maximum burst size allowed by the hardware's buffer size. +- max-burst-mem-write: limit burst size for memory writes + (DMA_DEV_TO_MEM/DMA_MEM_TO_MEM) to this value, specified in bytes, rather + than using the maximum burst size allowed by the hardware's buffer size. + If both max-burst-mem-read and max-burst-mem-write are set, DMA_MEM_TO_MEM + will use the lower value. You can use dma-channels and dma-requests as described in dma.txt, although they won't be used, this information is derived from the compatibility string. diff --git a/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt b/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt index fd5618bd8fbc..55492c264d17 100644 --- a/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt +++ b/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt @@ -5,13 +5,13 @@ memcpy and memset capabilities. It has been designed for virtualized environments. Each HIDMA HW instance consists of multiple DMA channels. These channels -share the same bandwidth. The bandwidth utilization can be parititioned +share the same bandwidth. The bandwidth utilization can be partitioned among channels based on the priority and weight assignments. There are only two priority levels and 15 weigh assignments possible. Other parameters here determine how much of the system bus this HIDMA -instance can use like maximum read/write request and and number of bytes to +instance can use like maximum read/write request and number of bytes to read/write in a single burst. Main node required properties: @@ -47,12 +47,18 @@ When the OS is not in control of the management interface (i.e. it's a guest), the channel nodes appear on their own, not under a management node. Required properties: -- compatible: must contain "qcom,hidma-1.0" +- compatible: must contain "qcom,hidma-1.0" for initial HW or "qcom,hidma-1.1" +for MSI capable HW. - reg: Addresses for the transfer and event channel - interrupts: Should contain the event interrupt - desc-count: Number of asynchronous requests this channel can handle - iommus: required a iommu node +Optional properties for MSI: +- msi-parent : See the generic MSI binding described in + devicetree/bindings/interrupt-controller/msi.txt for a description of the + msi-parent property. + Example: Hypervisor OS configuration: diff --git a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt index 5f2ce669789a..3316a9c2e638 100644 --- a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt +++ b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt @@ -24,6 +24,7 @@ Required Properties: - "renesas,dmac-r8a7793" (R-Car M2-N) - "renesas,dmac-r8a7794" (R-Car E2) - "renesas,dmac-r8a7795" (R-Car H3) + - "renesas,dmac-r8a7796" (R-Car M3-W) - reg: base address and length of the registers block for the DMAC diff --git a/Documentation/devicetree/bindings/dma/snps-dma.txt b/Documentation/devicetree/bindings/dma/snps-dma.txt index 0f5583293c9c..4775c66f4508 100644 --- a/Documentation/devicetree/bindings/dma/snps-dma.txt +++ b/Documentation/devicetree/bindings/dma/snps-dma.txt @@ -27,6 +27,8 @@ Optional properties: that services interrupts for this device - is_private: The device channels should be marked as private and not for by the general purpose DMA channel allocator. False if not passed. +- multi-block: Multi block transfers supported by hardware. Array property with + one cell per channel. 0: not supported, 1 (default): supported. Example: diff --git a/Documentation/devicetree/bindings/dma/st_fdma.txt b/Documentation/devicetree/bindings/dma/st_fdma.txt new file mode 100644 index 000000000000..495d853c569b --- /dev/null +++ b/Documentation/devicetree/bindings/dma/st_fdma.txt @@ -0,0 +1,87 @@ +* STMicroelectronics Flexible Direct Memory Access Device Tree bindings + +The FDMA is a general-purpose direct memory access controller capable of +supporting 16 independent DMA channels. It accepts up to 32 DMA requests. +The FDMA is based on a Slim processor which requires a firmware. + +* FDMA Controller + +Required properties: +- compatible : Should be one of + - st,stih407-fdma-mpe31-11, "st,slim-rproc"; + - st,stih407-fdma-mpe31-12, "st,slim-rproc"; + - st,stih407-fdma-mpe31-13, "st,slim-rproc"; +- reg : Should contain an entry for each name in reg-names +- reg-names : Must contain "slimcore", "dmem", "peripherals", "imem" entries +- interrupts : Should contain one interrupt shared by all channels +- dma-channels : Number of channels supported by the controller +- #dma-cells : Must be <3>. See DMA client section below +- clocks : Must contain an entry for each clock +See: Documentation/devicetree/bindings/clock/clock-bindings.txt + + +Example: + + fdma0: dma-controller@8e20000 { + compatible = "st,stih407-fdma-mpe31-11", "st,slim-rproc"; + reg = <0x8e20000 0x8000>, + <0x8e30000 0x3000>, + <0x8e37000 0x1000>, + <0x8e38000 0x8000>; + reg-names = "slimcore", "dmem", "peripherals", "imem"; + clocks = <&clk_s_c0_flexgen CLK_FDMA>, + <&clk_s_c0_flexgen CLK_EXT2F_A9>, + <&clk_s_c0_flexgen CLK_EXT2F_A9>, + <&clk_s_c0_flexgen CLK_EXT2F_A9>; + interrupts = <GIC_SPI 5 IRQ_TYPE_NONE>; + dma-channels = <16>; + #dma-cells = <3>; + }; + +* DMA client + +Required properties: +- dmas: Comma separated list of dma channel requests +- dma-names: Names of the aforementioned requested channels + +Each dmas request consists of 4 cells: +1. A phandle pointing to the FDMA controller +2. The request line number +3. A 32bit mask specifying (see include/linux/platform_data/dma-st-fdma.h) + -bit 2-0: Holdoff value, dreq will be masked for + 0x0: 0-0.5us + 0x1: 0.5-1us + 0x2: 1-1.5us + -bit 17: data swap + 0x0: disabled + 0x1: enabled + -bit 21: Increment Address + 0x0: no address increment between transfers + 0x1: increment address between transfers + -bit 22: 2 STBus Initiator Coprocessor interface + 0x0: high priority port + 0x1: low priority port +4. transfers type + 0 free running + 1 paced + +Example: + + sti_uni_player2: sti-uni-player@2 { + compatible = "st,sti-uni-player"; + status = "disabled"; + #sound-dai-cells = <0>; + st,syscfg = <&syscfg_core>; + clocks = <&clk_s_d0_flexgen CLK_PCM_2>; + assigned-clocks = <&clk_s_d0_flexgen CLK_PCM_2>; + assigned-clock-parents = <&clk_s_d0_quadfs 2>; + assigned-clock-rates = <50000000>; + reg = <0x8D82000 0x158>; + interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>; + dmas = <&fdma0 4 0 1>; + dai-name = "Uni Player #1 (DAC)"; + dma-names = "tx"; + st,uniperiph-id = <2>; + st,version = <5>; + st,mode = "PCM"; + }; diff --git a/Documentation/devicetree/bindings/dma/stm32-dma.txt b/Documentation/devicetree/bindings/dma/stm32-dma.txt index 70cd13f1588a..4408af693d0c 100644 --- a/Documentation/devicetree/bindings/dma/stm32-dma.txt +++ b/Documentation/devicetree/bindings/dma/stm32-dma.txt @@ -40,8 +40,7 @@ Example: DMA clients connected to the STM32 DMA controller must use the format described in the dma.txt file, using a five-cell specifier for each -channel: a phandle plus four integer cells. -The four cells in order are: +channel: a phandle to the DMA controller plus the following four integer cells: 1. The channel id 2. The request line number @@ -61,7 +60,7 @@ The four cells in order are: 0x1: medium 0x2: high 0x3: very high -5. A 32bit mask specifying the DMA FIFO threshold configuration which are device +4. A 32bit mask specifying the DMA FIFO threshold configuration which are device dependent: -bit 0-1: Fifo threshold 0x0: 1/4 full FIFO diff --git a/Documentation/devicetree/bindings/eeprom/eeprom.txt b/Documentation/devicetree/bindings/eeprom/eeprom.txt index 735bc94444bb..5696eb508e95 100644 --- a/Documentation/devicetree/bindings/eeprom/eeprom.txt +++ b/Documentation/devicetree/bindings/eeprom/eeprom.txt @@ -10,6 +10,8 @@ Required properties: "catalyst,24c32" + "microchip,24c128" + "ramtron,24c64" "renesas,r1ex24002" diff --git a/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt b/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt index af0b903de293..dfc14f71e81f 100644 --- a/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt +++ b/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt @@ -5,7 +5,10 @@ connected to a GPIO pin. Required properties: - compatible: Should be "linux,extcon-usb-gpio" + +Either one of id-gpio or vbus-gpio must be present. Both can be present as well. - id-gpio: gpio for USB ID pin. See gpio binding. +- vbus-gpio: gpio for USB VBUS pin. Example: Examples of extcon-usb-gpio node in dra7-evm.dts as listed below: extcon_usb1 { diff --git a/Documentation/devicetree/bindings/firmware/nvidia,tegra186-bpmp.txt b/Documentation/devicetree/bindings/firmware/nvidia,tegra186-bpmp.txt new file mode 100644 index 000000000000..e821e16ad65b --- /dev/null +++ b/Documentation/devicetree/bindings/firmware/nvidia,tegra186-bpmp.txt @@ -0,0 +1,108 @@ +NVIDIA Tegra Boot and Power Management Processor (BPMP) + +The BPMP is a specific processor in Tegra chip, which is designed for +booting process handling and offloading the power management, clock +management, and reset control tasks from the CPU. The binding document +defines the resources that would be used by the BPMP firmware driver, +which can create the interprocessor communication (IPC) between the CPU +and BPMP. + +Required properties: +- name : Should be bpmp +- compatible + Array of strings + One of: + - "nvidia,tegra186-bpmp" +- mboxes : The phandle of mailbox controller and the mailbox specifier. +- shmem : List of the phandle of the TX and RX shared memory area that + the IPC between CPU and BPMP is based on. +- #clock-cells : Should be 1. +- #power-domain-cells : Should be 1. +- #reset-cells : Should be 1. + +This node is a mailbox consumer. See the following files for details of +the mailbox subsystem, and the specifiers implemented by the relevant +provider(s): + +- .../mailbox/mailbox.txt +- .../mailbox/nvidia,tegra186-hsp.txt + +This node is a clock, power domain, and reset provider. See the following +files for general documentation of those features, and the specifiers +implemented by this node: + +- .../clock/clock-bindings.txt +- <dt-bindings/clock/tegra186-clock.h> +- ../power/power_domain.txt +- <dt-bindings/power/tegra186-powergate.h> +- .../reset/reset.txt +- <dt-bindings/reset/tegra186-reset.h> + +The BPMP implements some services which must be represented by separate nodes. +For example, it can provide access to certain I2C controllers, and the I2C +bindings represent each I2C controller as a device tree node. Such nodes should +be nested directly inside the main BPMP node. + +Software can determine whether a child node of the BPMP node represents a device +by checking for a compatible property. Any node with a compatible property +represents a device that can be instantiated. Nodes without a compatible +property may be used to provide configuration information regarding the BPMP +itself, although no such configuration nodes are currently defined by this +binding. + +The BPMP firmware defines no single global name-/numbering-space for such +services. Put another way, the numbering scheme for I2C buses is distinct from +the numbering scheme for any other service the BPMP may provide (e.g. a future +hypothetical SPI bus service). As such, child device nodes will have no reg +property, and the BPMP node will have no #address-cells or #size-cells property. + +The shared memory bindings for BPMP +----------------------------------- + +The shared memory area for the IPC TX and RX between CPU and BPMP are +predefined and work on top of sysram, which is an SRAM inside the chip. + +See ".../sram/sram.txt" for the bindings. + +Example: + +hsp_top0: hsp@03c00000 { + ... + #mbox-cells = <2>; +}; + +sysram@30000000 { + compatible = "nvidia,tegra186-sysram", "mmio-sram"; + reg = <0x0 0x30000000 0x0 0x50000>; + #address-cells = <2>; + #size-cells = <2>; + ranges = <0 0x0 0x0 0x30000000 0x0 0x50000>; + + cpu_bpmp_tx: shmem@4e000 { + compatible = "nvidia,tegra186-bpmp-shmem"; + reg = <0x0 0x4e000 0x0 0x1000>; + label = "cpu-bpmp-tx"; + pool; + }; + + cpu_bpmp_rx: shmem@4f000 { + compatible = "nvidia,tegra186-bpmp-shmem"; + reg = <0x0 0x4f000 0x0 0x1000>; + label = "cpu-bpmp-rx"; + pool; + }; +}; + +bpmp { + compatible = "nvidia,tegra186-bpmp"; + mboxes = <&hsp_top0 TEGRA_HSP_MBOX_TYPE_DB TEGRA_HSP_DB_MASTER_BPMP>; + shmem = <&cpu_bpmp_tx &cpu_bpmp_rx>; + #clock-cells = <1>; + #power-domain-cells = <1>; + #reset-cells = <1>; + + i2c { + compatible = "..."; + ... + }; +}; diff --git a/Documentation/devicetree/bindings/firmware/qcom,scm.txt b/Documentation/devicetree/bindings/firmware/qcom,scm.txt index 3b4436e56865..20f26fbce875 100644 --- a/Documentation/devicetree/bindings/firmware/qcom,scm.txt +++ b/Documentation/devicetree/bindings/firmware/qcom,scm.txt @@ -10,8 +10,10 @@ Required properties: * "qcom,scm-apq8064" for APQ8064 platforms * "qcom,scm-msm8660" for MSM8660 platforms * "qcom,scm-msm8690" for MSM8690 platforms + * "qcom,scm-msm8996" for MSM8996 platforms * "qcom,scm" for later processors (MSM8916, APQ8084, MSM8974, etc) - clocks: One to three clocks may be required based on compatible. + * No clock required for "qcom,scm-msm8996" * Only core clock required for "qcom,scm-apq8064", "qcom,scm-msm8660", and "qcom,scm-msm8960" * Core, iface, and bus clocks required for "qcom,scm" - clock-names: Must contain "core" for the core clock, "iface" for the interface diff --git a/Documentation/devicetree/bindings/fpga/altera-fpga2sdram-bridge.txt b/Documentation/devicetree/bindings/fpga/altera-fpga2sdram-bridge.txt new file mode 100644 index 000000000000..817a8d4bf903 --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/altera-fpga2sdram-bridge.txt @@ -0,0 +1,16 @@ +Altera FPGA To SDRAM Bridge Driver + +Required properties: +- compatible : Should contain "altr,socfpga-fpga2sdram-bridge" + +Optional properties: +- bridge-enable : 0 if driver should disable bridge at startup + 1 if driver should enable bridge at startup + Default is to leave bridge in current state. + +Example: + fpga_bridge3: fpga-bridge@ffc25080 { + compatible = "altr,socfpga-fpga2sdram-bridge"; + reg = <0xffc25080 0x4>; + bridge-enable = <0>; + }; diff --git a/Documentation/devicetree/bindings/fpga/altera-freeze-bridge.txt b/Documentation/devicetree/bindings/fpga/altera-freeze-bridge.txt new file mode 100644 index 000000000000..f8e288c71b2d --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/altera-freeze-bridge.txt @@ -0,0 +1,23 @@ +Altera Freeze Bridge Controller Driver + +The Altera Freeze Bridge Controller manages one or more freeze bridges. +The controller can freeze/disable the bridges which prevents signal +changes from passing through the bridge. The controller can also +unfreeze/enable the bridges which allows traffic to pass through the +bridge normally. + +Required properties: +- compatible : Should contain "altr,freeze-bridge-controller" +- regs : base address and size for freeze bridge module + +Optional properties: +- bridge-enable : 0 if driver should disable bridge at startup + 1 if driver should enable bridge at startup + Default is to leave bridge in current state. + +Example: + freeze-controller@100000450 { + compatible = "altr,freeze-bridge-controller"; + regs = <0x1000 0x10>; + bridge-enable = <0>; + }; diff --git a/Documentation/devicetree/bindings/fpga/altera-hps2fpga-bridge.txt b/Documentation/devicetree/bindings/fpga/altera-hps2fpga-bridge.txt new file mode 100644 index 000000000000..6406f9337eeb --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/altera-hps2fpga-bridge.txt @@ -0,0 +1,39 @@ +Altera FPGA/HPS Bridge Driver + +Required properties: +- regs : base address and size for AXI bridge module +- compatible : Should contain one of: + "altr,socfpga-lwhps2fpga-bridge", + "altr,socfpga-hps2fpga-bridge", or + "altr,socfpga-fpga2hps-bridge" +- resets : Phandle and reset specifier for this bridge's reset +- clocks : Clocks used by this module. + +Optional properties: +- bridge-enable : 0 if driver should disable bridge at startup. + 1 if driver should enable bridge at startup. + Default is to leave bridge in its current state. + +Example: + fpga_bridge0: fpga-bridge@ff400000 { + compatible = "altr,socfpga-lwhps2fpga-bridge"; + reg = <0xff400000 0x100000>; + resets = <&rst LWHPS2FPGA_RESET>; + clocks = <&l4_main_clk>; + bridge-enable = <0>; + }; + + fpga_bridge1: fpga-bridge@ff500000 { + compatible = "altr,socfpga-hps2fpga-bridge"; + reg = <0xff500000 0x10000>; + resets = <&rst HPS2FPGA_RESET>; + clocks = <&l4_main_clk>; + bridge-enable = <1>; + }; + + fpga_bridge2: fpga-bridge@ff600000 { + compatible = "altr,socfpga-fpga2hps-bridge"; + reg = <0xff600000 0x100000>; + resets = <&rst FPGA2HPS_RESET>; + clocks = <&l4_main_clk>; + }; diff --git a/Documentation/devicetree/bindings/fpga/altera-socfpga-a10-fpga-mgr.txt b/Documentation/devicetree/bindings/fpga/altera-socfpga-a10-fpga-mgr.txt new file mode 100644 index 000000000000..2fd8e7a84734 --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/altera-socfpga-a10-fpga-mgr.txt @@ -0,0 +1,19 @@ +Altera SOCFPGA Arria10 FPGA Manager + +Required properties: +- compatible : should contain "altr,socfpga-a10-fpga-mgr" +- reg : base address and size for memory mapped io. + - The first index is for FPGA manager register access. + - The second index is for writing FPGA configuration data. +- resets : Phandle and reset specifier for the device's reset. +- clocks : Clocks used by the device. + +Example: + + fpga_mgr: fpga-mgr@ffd03000 { + compatible = "altr,socfpga-a10-fpga-mgr"; + reg = <0xffd03000 0x100 + 0xffcfe400 0x20>; + clocks = <&l4_mp_clk>; + resets = <&rst FPGAMGR_RESET>; + }; diff --git a/Documentation/devicetree/bindings/fpga/fpga-region.txt b/Documentation/devicetree/bindings/fpga/fpga-region.txt new file mode 100644 index 000000000000..3b32ba15a717 --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/fpga-region.txt @@ -0,0 +1,494 @@ +FPGA Region Device Tree Binding + +Alan Tull 2016 + + CONTENTS + - Introduction + - Terminology + - Sequence + - FPGA Region + - Supported Use Models + - Device Tree Examples + - Constraints + + +Introduction +============ + +FPGA Regions represent FPGA's and partial reconfiguration regions of FPGA's in +the Device Tree. FPGA Regions provide a way to program FPGAs under device tree +control. + +This device tree binding document hits some of the high points of FPGA usage and +attempts to include terminology used by both major FPGA manufacturers. This +document isn't a replacement for any manufacturers specifications for FPGA +usage. + + +Terminology +=========== + +Full Reconfiguration + * The entire FPGA is programmed. + +Partial Reconfiguration (PR) + * A section of an FPGA is reprogrammed while the rest of the FPGA is not + affected. + * Not all FPGA's support PR. + +Partial Reconfiguration Region (PRR) + * Also called a "reconfigurable partition" + * A PRR is a specific section of a FPGA reserved for reconfiguration. + * A base (or static) FPGA image may create a set of PRR's that later may + be independently reprogrammed many times. + * The size and specific location of each PRR is fixed. + * The connections at the edge of each PRR are fixed. The image that is loaded + into a PRR must fit and must use a subset of the region's connections. + * The busses within the FPGA are split such that each region gets its own + branch that may be gated independently. + +Persona + * Also called a "partial bit stream" + * An FPGA image that is designed to be loaded into a PRR. There may be + any number of personas designed to fit into a PRR, but only one at at time + may be loaded. + * A persona may create more regions. + +FPGA Bridge + * FPGA Bridges gate bus signals between a host and FPGA. + * FPGA Bridges should be disabled while the FPGA is being programmed to + prevent spurious signals on the cpu bus and to the soft logic. + * FPGA bridges may be actual hardware or soft logic on an FPGA. + * During Full Reconfiguration, hardware bridges between the host and FPGA + will be disabled. + * During Partial Reconfiguration of a specific region, that region's bridge + will be used to gate the busses. Traffic to other regions is not affected. + * In some implementations, the FPGA Manager transparantly handles gating the + buses, eliminating the need to show the hardware FPGA bridges in the + device tree. + * An FPGA image may create a set of reprogrammable regions, each having its + own bridge and its own split of the busses in the FPGA. + +FPGA Manager + * An FPGA Manager is a hardware block that programs an FPGA under the control + of a host processor. + +Base Image + * Also called the "static image" + * An FPGA image that is designed to do full reconfiguration of the FPGA. + * A base image may set up a set of partial reconfiguration regions that may + later be reprogrammed. + + ---------------- ---------------------------------- + | Host CPU | | FPGA | + | | | | + | ----| | ----------- -------- | + | | H | | |==>| Bridge0 |<==>| PRR0 | | + | | W | | | ----------- -------- | + | | | | | | + | | B |<=====>|<==| ----------- -------- | + | | R | | |==>| Bridge1 |<==>| PRR1 | | + | | I | | | ----------- -------- | + | | D | | | | + | | G | | | ----------- -------- | + | | E | | |==>| Bridge2 |<==>| PRR2 | | + | ----| | ----------- -------- | + | | | | + ---------------- ---------------------------------- + +Figure 1: An FPGA set up with a base image that created three regions. Each +region (PRR0-2) gets its own split of the busses that is independently gated by +a soft logic bridge (Bridge0-2) in the FPGA. The contents of each PRR can be +reprogrammed independently while the rest of the system continues to function. + + +Sequence +======== + +When a DT overlay that targets a FPGA Region is applied, the FPGA Region will +do the following: + + 1. Disable appropriate FPGA bridges. + 2. Program the FPGA using the FPGA manager. + 3. Enable the FPGA bridges. + 4. The Device Tree overlay is accepted into the live tree. + 5. Child devices are populated. + +When the overlay is removed, the child nodes will be removed and the FPGA Region +will disable the bridges. + + +FPGA Region +=========== + +FPGA Regions represent FPGA's and FPGA PR regions in the device tree. An FPGA +Region brings together the elements needed to program on a running system and +add the child devices: + + * FPGA Manager + * FPGA Bridges + * image-specific information needed to to the programming. + * child nodes + +The intended use is that a Device Tree overlay (DTO) can be used to reprogram an +FPGA while an operating system is running. + +An FPGA Region that exists in the live Device Tree reflects the current state. +If the live tree shows a "firmware-name" property or child nodes under a FPGA +Region, the FPGA already has been programmed. A DTO that targets a FPGA Region +and adds the "firmware-name" property is taken as a request to reprogram the +FPGA. After reprogramming is successful, the overlay is accepted into the live +tree. + +The base FPGA Region in the device tree represents the FPGA and supports full +reconfiguration. It must include a phandle to an FPGA Manager. The base +FPGA region will be the child of one of the hardware bridges (the bridge that +allows register access) between the cpu and the FPGA. If there are more than +one bridge to control during FPGA programming, the region will also contain a +list of phandles to the additional hardware FPGA Bridges. + +For partial reconfiguration (PR), each PR region will have an FPGA Region. +These FPGA regions are children of FPGA bridges which are then children of the +base FPGA region. The "Full Reconfiguration to add PRR's" example below shows +this. + +If an FPGA Region does not specify a FPGA Manager, it will inherit the FPGA +Manager specified by its ancestor FPGA Region. This supports both the case +where the same FPGA Manager is used for all of a FPGA as well the case where +a different FPGA Manager is used for each region. + +FPGA Regions do not inherit their ancestor FPGA regions' bridges. This prevents +shutting down bridges that are upstream from the other active regions while one +region is getting reconfigured (see Figure 1 above). During PR, the FPGA's +hardware bridges remain enabled. The PR regions' bridges will be FPGA bridges +within the static image of the FPGA. + +Required properties: +- compatible : should contain "fpga-region" +- fpga-mgr : should contain a phandle to an FPGA Manager. Child FPGA Regions + inherit this property from their ancestor regions. A fpga-mgr property + in a region will override any inherited FPGA manager. +- #address-cells, #size-cells, ranges : must be present to handle address space + mapping for child nodes. + +Optional properties: +- firmware-name : should contain the name of an FPGA image file located on the + firmware search path. If this property shows up in a live device tree + it indicates that the FPGA has already been programmed with this image. + If this property is in an overlay targeting a FPGA region, it is a + request to program the FPGA with that image. +- fpga-bridges : should contain a list of phandles to FPGA Bridges that must be + controlled during FPGA programming along with the parent FPGA bridge. + This property is optional if the FPGA Manager handles the bridges. + If the fpga-region is the child of a fpga-bridge, the list should not + contain the parent bridge. +- partial-fpga-config : boolean, set if partial reconfiguration is to be done, + otherwise full reconfiguration is done. +- external-fpga-config : boolean, set if the FPGA has already been configured + prior to OS boot up. +- region-unfreeze-timeout-us : The maximum time in microseconds to wait for + bridges to successfully become enabled after the region has been + programmed. +- region-freeze-timeout-us : The maximum time in microseconds to wait for + bridges to successfully become disabled before the region has been + programmed. +- child nodes : devices in the FPGA after programming. + +In the example below, when an overlay is applied targeting fpga-region0, +fpga_mgr is used to program the FPGA. Two bridges are controlled during +programming: the parent fpga_bridge0 and fpga_bridge1. Because the region is +the child of fpga_bridge0, only fpga_bridge1 needs to be specified in the +fpga-bridges property. During programming, these bridges are disabled, the +firmware specified in the overlay is loaded to the FPGA using the FPGA manager +specified in the region. If FPGA programming succeeds, the bridges are +reenabled and the overlay makes it into the live device tree. The child devices +are then populated. If FPGA programming fails, the bridges are left disabled +and the overlay is rejected. The overlay's ranges property maps the lwhps +bridge's region (0xff200000) and the hps bridge's region (0xc0000000) for use by +the two child devices. + +Example: +Base tree contains: + + fpga_mgr: fpga-mgr@ff706000 { + compatible = "altr,socfpga-fpga-mgr"; + reg = <0xff706000 0x1000 + 0xffb90000 0x20>; + interrupts = <0 175 4>; + }; + + fpga_bridge0: fpga-bridge@ff400000 { + compatible = "altr,socfpga-lwhps2fpga-bridge"; + reg = <0xff400000 0x100000>; + resets = <&rst LWHPS2FPGA_RESET>; + clocks = <&l4_main_clk>; + + #address-cells = <1>; + #size-cells = <1>; + ranges; + + fpga_region0: fpga-region0 { + compatible = "fpga-region"; + fpga-mgr = <&fpga_mgr>; + }; + }; + + fpga_bridge1: fpga-bridge@ff500000 { + compatible = "altr,socfpga-hps2fpga-bridge"; + reg = <0xff500000 0x10000>; + resets = <&rst HPS2FPGA_RESET>; + clocks = <&l4_main_clk>; + }; + +Overlay contains: + +/dts-v1/ /plugin/; +/ { + fragment@0 { + target = <&fpga_region0>; + #address-cells = <1>; + #size-cells = <1>; + __overlay__ { + #address-cells = <1>; + #size-cells = <1>; + + firmware-name = "soc_system.rbf"; + fpga-bridges = <&fpga_bridge1>; + ranges = <0x20000 0xff200000 0x100000>, + <0x0 0xc0000000 0x20000000>; + + gpio@10040 { + compatible = "altr,pio-1.0"; + reg = <0x10040 0x20>; + altr,gpio-bank-width = <4>; + #gpio-cells = <2>; + clocks = <2>; + gpio-controller; + }; + + onchip-memory { + device_type = "memory"; + compatible = "altr,onchipmem-15.1"; + reg = <0x0 0x10000>; + }; + }; + }; +}; + + +Supported Use Models +==================== + +In all cases the live DT must have the FPGA Manager, FPGA Bridges (if any), and +a FPGA Region. The target of the Device Tree Overlay is the FPGA Region. Some +uses are specific to a FPGA device. + + * No FPGA Bridges + In this case, the FPGA Manager which programs the FPGA also handles the + bridges behind the scenes. No FPGA Bridge devices are needed for full + reconfiguration. + + * Full reconfiguration with hardware bridges + In this case, there are hardware bridges between the processor and FPGA that + need to be controlled during full reconfiguration. Before the overlay is + applied, the live DT must include the FPGA Manager, FPGA Bridges, and a + FPGA Region. The FPGA Region is the child of the bridge that allows + register access to the FPGA. Additional bridges may be listed in a + fpga-bridges property in the FPGA region or in the device tree overlay. + + * Partial reconfiguration with bridges in the FPGA + In this case, the FPGA will have one or more PRR's that may be programmed + separately while the rest of the FPGA can remain active. To manage this, + bridges need to exist in the FPGA that can gate the buses going to each FPGA + region while the buses are enabled for other sections. Before any partial + reconfiguration can be done, a base FPGA image must be loaded which includes + PRR's with FPGA bridges. The device tree should have a FPGA region for each + PRR. + +Device Tree Examples +==================== + +The intention of this section is to give some simple examples, focusing on +the placement of the elements detailed above, especially: + * FPGA Manager + * FPGA Bridges + * FPGA Region + * ranges + * target-path or target + +For the purposes of this section, I'm dividing the Device Tree into two parts, +each with its own requirements. The two parts are: + * The live DT prior to the overlay being added + * The DT overlay + +The live Device Tree must contain an FPGA Region, an FPGA Manager, and any FPGA +Bridges. The FPGA Region's "fpga-mgr" property specifies the manager by phandle +to handle programming the FPGA. If the FPGA Region is the child of another FPGA +Region, the parent's FPGA Manager is used. If FPGA Bridges need to be involved, +they are specified in the FPGA Region by the "fpga-bridges" property. During +FPGA programming, the FPGA Region will disable the bridges that are in its +"fpga-bridges" list and will re-enable them after FPGA programming has +succeeded. + +The Device Tree Overlay will contain: + * "target-path" or "target" + The insertion point where the the contents of the overlay will go into the + live tree. target-path is a full path, while target is a phandle. + * "ranges" + The address space mapping from processor to FPGA bus(ses). + * "firmware-name" + Specifies the name of the FPGA image file on the firmware search + path. The search path is described in the firmware class documentation. + * "partial-fpga-config" + This binding is a boolean and should be present if partial reconfiguration + is to be done. + * child nodes corresponding to hardware that will be loaded in this region of + the FPGA. + +Device Tree Example: Full Reconfiguration without Bridges +========================================================= + +Live Device Tree contains: + fpga_mgr0: fpga-mgr@f8007000 { + compatible = "xlnx,zynq-devcfg-1.0"; + reg = <0xf8007000 0x100>; + interrupt-parent = <&intc>; + interrupts = <0 8 4>; + clocks = <&clkc 12>; + clock-names = "ref_clk"; + syscon = <&slcr>; + }; + + fpga_region0: fpga-region0 { + compatible = "fpga-region"; + fpga-mgr = <&fpga_mgr0>; + #address-cells = <0x1>; + #size-cells = <0x1>; + ranges; + }; + +DT Overlay contains: +/dts-v1/ /plugin/; +/ { +fragment@0 { + target = <&fpga_region0>; + #address-cells = <1>; + #size-cells = <1>; + __overlay__ { + #address-cells = <1>; + #size-cells = <1>; + + firmware-name = "zynq-gpio.bin"; + + gpio1: gpio@40000000 { + compatible = "xlnx,xps-gpio-1.00.a"; + reg = <0x40000000 0x10000>; + gpio-controller; + #gpio-cells = <0x2>; + xlnx,gpio-width= <0x6>; + }; + }; +}; + +Device Tree Example: Full Reconfiguration to add PRR's +====================================================== + +The base FPGA Region is specified similar to the first example above. + +This example programs the FPGA to have two regions that can later be partially +configured. Each region has its own bridge in the FPGA fabric. + +DT Overlay contains: +/dts-v1/ /plugin/; +/ { + fragment@0 { + target = <&fpga_region0>; + #address-cells = <1>; + #size-cells = <1>; + __overlay__ { + #address-cells = <1>; + #size-cells = <1>; + + firmware-name = "base.rbf"; + + fpga-bridge@4400 { + compatible = "altr,freeze-bridge"; + reg = <0x4400 0x10>; + + fpga_region1: fpga-region1 { + compatible = "fpga-region"; + #address-cells = <0x1>; + #size-cells = <0x1>; + ranges; + }; + }; + + fpga-bridge@4420 { + compatible = "altr,freeze-bridge"; + reg = <0x4420 0x10>; + + fpga_region2: fpga-region2 { + compatible = "fpga-region"; + #address-cells = <0x1>; + #size-cells = <0x1>; + ranges; + }; + }; + }; + }; +}; + +Device Tree Example: Partial Reconfiguration +============================================ + +This example reprograms one of the PRR's set up in the previous example. + +The sequence that occurs when this overlay is similar to the above, the only +differences are that the FPGA is partially reconfigured due to the +"partial-fpga-config" boolean and the only bridge that is controlled during +programming is the FPGA based bridge of fpga_region1. + +/dts-v1/ /plugin/; +/ { + fragment@0 { + target = <&fpga_region1>; + #address-cells = <1>; + #size-cells = <1>; + __overlay__ { + #address-cells = <1>; + #size-cells = <1>; + + firmware-name = "soc_image2.rbf"; + partial-fpga-config; + + gpio@10040 { + compatible = "altr,pio-1.0"; + reg = <0x10040 0x20>; + clocks = <0x2>; + altr,gpio-bank-width = <0x4>; + resetvalue = <0x0>; + #gpio-cells = <0x2>; + gpio-controller; + }; + }; + }; +}; + +Constraints +=========== + +It is beyond the scope of this document to fully describe all the FPGA design +constraints required to make partial reconfiguration work[1] [2] [3], but a few +deserve quick mention. + +A persona must have boundary connections that line up with those of the partion +or region it is designed to go into. + +During programming, transactions through those connections must be stopped and +the connections must be held at a fixed logic level. This can be achieved by +FPGA Bridges that exist on the FPGA fabric prior to the partial reconfiguration. + +-- +[1] www.altera.com/content/dam/altera-www/global/en_US/pdfs/literature/ug/ug_partrecon.pdf +[2] tspace.library.utoronto.ca/bitstream/1807/67932/1/Byma_Stuart_A_201411_MAS_thesis.pdf +[3] http://www.xilinx.com/support/documentation/sw_manuals/xilinx14_1/ug702.pdf diff --git a/Documentation/devicetree/bindings/gpio/cortina,gemini-gpio.txt b/Documentation/devicetree/bindings/gpio/cortina,gemini-gpio.txt new file mode 100644 index 000000000000..5c9246c054e5 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/cortina,gemini-gpio.txt @@ -0,0 +1,24 @@ +Cortina Systems Gemini GPIO Controller + +Required properties: + +- compatible : Must be "cortina,gemini-gpio" +- reg : Should contain registers location and length +- interrupts : Should contain the interrupt line for the GPIO block +- gpio-controller : marks this as a GPIO controller +- #gpio-cells : Should be 2, see gpio/gpio.txt +- interrupt-controller : marks this as an interrupt controller +- #interrupt-cells : a standard two-cell interrupt flag, see + interrupt-controller/interrupts.txt + +Example: + +gpio@4d000000 { + compatible = "cortina,gemini-gpio"; + reg = <0x4d000000 0x100>; + interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt index 08dd15f89ba9..e63935710011 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt @@ -29,6 +29,10 @@ Required properties: onsemi,pca9654 exar,xra1202 +Optional properties: + - reset-gpios: GPIO specification for the RESET input. This is an + active low signal to the PCA953x. + Example: diff --git a/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt b/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt deleted file mode 100644 index c809acb9c71b..000000000000 --- a/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt +++ /dev/null @@ -1,41 +0,0 @@ -SEMTECH SX150x GPIO expander bindings - - -Required properties: - -- compatible: should be "semtech,sx1506q", - "semtech,sx1508q", - "semtech,sx1509q", - "semtech,sx1502q". - -- reg: The I2C slave address for this device. - -- interrupt-parent: phandle of the parent interrupt controller. - -- interrupts: Interrupt specifier for the controllers interrupt. - -- #gpio-cells: Should be 2. The first cell is the GPIO number and the - second cell is used to specify optional parameters: - bit 0: polarity (0: normal, 1: inverted) - -- gpio-controller: Marks the device as a GPIO controller. - -- interrupt-controller: Marks the device as a interrupt controller. - -The GPIO expander can optionally be used as an interrupt controller, in -which case it uses the default two cell specifier as described in -Documentation/devicetree/bindings/interrupt-controller/interrupts.txt. - -Example: - - i2c_gpio_expander@20{ - #gpio-cells = <2>; - #interrupt-cells = <2>; - compatible = "semtech,sx1506q"; - reg = <0x20>; - interrupt-parent = <&gpio_1>; - interrupts = <16 0>; - - gpio-controller; - interrupt-controller; - }; diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index 68d28f62a6f4..84ede036f73d 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -187,10 +187,10 @@ gpio-controller's driver probe function. Each GPIO hog definition is represented as a child node of the GPIO controller. Required properties: -- gpio-hog: A property specifying that this child node represent a GPIO hog. -- gpios: Store the GPIO information (id, flags, ...). Shall contain the - number of cells specified in its parent node (GPIO controller - node). +- gpio-hog: A property specifying that this child node represents a GPIO hog. +- gpios: Store the GPIO information (id, flags, ...) for each GPIO to + affect. Shall contain an integer multiple of the number of cells + specified in its parent node (GPIO controller node). Only one of the following properties scanned in the order shown below. This means that when multiple properties are present they will be searched in the order presented below and the first match is taken as the intended diff --git a/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt b/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt index 928ed4f43907..966514744df4 100644 --- a/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt +++ b/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt @@ -3,7 +3,7 @@ Please refer to gpio.txt for generic information regarding GPIO bindings. Required properties: - - compatible: "oxsemi,ox810se-gpio" + - compatible: "oxsemi,ox810se-gpio" or "oxsemi,ox820-gpio" - reg: Base address and length for the device. - interrupts: The port interrupt shared by all pins. - gpio-controller: Marks the port as GPIO controller. diff --git a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt index c3d016532d8e..30fd2201b3d4 100644 --- a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt @@ -17,7 +17,9 @@ Required properties: - #interrupt-cells: Specifies the number of cells needed to encode an interrupt source. - gpio-controller : Marks the device node as a gpio controller. -- #gpio-cells : Should be one. It is the pin number. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify flags. See gpio.txt for possible + values. Example for a MMP platform: @@ -27,7 +29,7 @@ Example for a MMP platform: interrupts = <49>; interrupt-names = "gpio_mux"; gpio-controller; - #gpio-cells = <1>; + #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt new file mode 100644 index 000000000000..476f5ea6c627 --- /dev/null +++ b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt @@ -0,0 +1,81 @@ +ARM Mali Utgard GPU +=================== + +Required properties: + - compatible + * Must be one of the following: + + "arm,mali-300" + + "arm,mali-400" + + "arm,mali-450" + * And, optionally, one of the vendor specific compatible: + + allwinner,sun4i-a10-mali + + allwinner,sun7i-a20-mali + + amlogic,meson-gxbb-mali + + amlogic,meson-gxl-mali + + stericsson,db8500-mali + + - reg: Physical base address and length of the GPU registers + + - interrupts: an entry for each entry in interrupt-names. + See ../interrupt-controller/interrupts.txt for details. + + - interrupt-names: + * ppX: Pixel Processor X interrupt (X from 0 to 7) + * ppmmuX: Pixel Processor X MMU interrupt (X from 0 to 7) + * pp: Pixel Processor broadcast interrupt (mali-450 only) + * gp: Geometry Processor interrupt + * gpmmu: Geometry Processor MMU interrupt + + - clocks: an entry for each entry in clock-names + - clock-names: + * bus: bus clock for the GPU + * core: clock driving the GPU itself + +Optional properties: + - interrupt-names and interrupts: + * pmu: Power Management Unit interrupt, if implemented in hardware + +Vendor-specific bindings +------------------------ + +The Mali GPU is integrated very differently from one SoC to +another. In order to accomodate those differences, you have the option +to specify one more vendor-specific compatible, among: + + - allwinner,sun4i-a10-mali + Required properties: + * resets: phandle to the reset line for the GPU + + - allwinner,sun7i-a20-mali + Required properties: + * resets: phandle to the reset line for the GPU + + - stericsson,db8500-mali + Required properties: + * interrupt-names and interrupts: + + combined: combined interrupt of all of the above lines + +Example: + +mali: gpu@1c40000 { + compatible = "allwinner,sun7i-a20-mali", "arm,mali-400"; + reg = <0x01c40000 0x10000>; + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "gp", + "gpmmu", + "pp0", + "ppmmu0", + "pp1", + "ppmmu1", + "pmu"; + clocks = <&ccu CLK_BUS_GPU>, <&ccu CLK_GPU>; + clock-names = "bus", "core"; + resets = <&ccu RST_BUS_GPU>; +}; + diff --git a/Documentation/devicetree/bindings/hwmon/adc128d818.txt b/Documentation/devicetree/bindings/hwmon/adc128d818.txt new file mode 100644 index 000000000000..08bab0e94d25 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/adc128d818.txt @@ -0,0 +1,38 @@ +TI ADC128D818 ADC System Monitor With Temperature Sensor +-------------------------------------------------------- + +Operation modes: + + - Mode 0: 7 single-ended voltage readings (IN0-IN6), + 1 temperature reading (internal) + - Mode 1: 8 single-ended voltage readings (IN0-IN7), + no temperature + - Mode 2: 4 pseudo-differential voltage readings + (IN0-IN1, IN3-IN2, IN4-IN5, IN7-IN6), + 1 temperature reading (internal) + - Mode 3: 4 single-ended voltage readings (IN0-IN3), + 2 pseudo-differential voltage readings + (IN4-IN5, IN7-IN6), + 1 temperature reading (internal) + +If no operation mode is configured via device tree, the driver keeps the +currently active chip operation mode (default is mode 0). + + +Required node properties: + + - compatible: must be set to "ti,adc128d818" + - reg: I2C address of the device + +Optional node properties: + + - ti,mode: Operation mode (see above). + + +Example (operation mode 2): + + adc128d818@1d { + compatible = "ti,adc128d818"; + reg = <0x1d>; + ti,mode = <2>; + }; diff --git a/Documentation/devicetree/bindings/hwmon/lm70.txt b/Documentation/devicetree/bindings/hwmon/lm70.txt index e7fd921aa4f1..ea417a0d32af 100644 --- a/Documentation/devicetree/bindings/hwmon/lm70.txt +++ b/Documentation/devicetree/bindings/hwmon/lm70.txt @@ -4,6 +4,7 @@ Required properties: - compatible: one of "ti,lm70" "ti,tmp121" + "ti,tmp122" "ti,lm71" "ti,lm74" diff --git a/Documentation/devicetree/bindings/hwmon/lm90.txt b/Documentation/devicetree/bindings/hwmon/lm90.txt index e8632486b9ef..97581266e329 100644 --- a/Documentation/devicetree/bindings/hwmon/lm90.txt +++ b/Documentation/devicetree/bindings/hwmon/lm90.txt @@ -33,6 +33,11 @@ Optional properties: LM90 "-ALERT" pin output. See interrupt-controller/interrupts.txt for the format. +- #thermal-sensor-cells: should be set to 1. See thermal/thermal.txt for + details. See <include/dt-bindings/thermal/lm90.h> for the + definition of the local, remote and 2nd remote sensor index + constants. + Example LM90 node: temp-sensor { @@ -41,4 +46,5 @@ temp-sensor { vcc-supply = <&palmas_ldo6_reg>; interrupt-parent = <&gpio>; interrupts = <TEGRA_GPIO(O, 4) IRQ_TYPE_LEVEL_LOW>; + #thermal-sensor-cells = <1>; } diff --git a/Documentation/devicetree/bindings/hwmon/mcp3021.txt b/Documentation/devicetree/bindings/hwmon/mcp3021.txt new file mode 100644 index 000000000000..294318ba6914 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/mcp3021.txt @@ -0,0 +1,21 @@ +mcp3021 properties + +Required properties: +- compatible: Must be one of the following: + - "microchip,mcp3021" for mcp3021 + - "microchip,mcp3221" for mcp3221 +- reg: I2C address + +Optional properties: + +- reference-voltage-microvolt + Reference voltage in microvolt (uV) + +Example: + +mcp3021@4d { + compatible = "microchip,mcp3021"; + reg = <0x4d>; + + reference-voltage-microvolt = <4500000>; /* 4.5 V */ +}; diff --git a/Documentation/devicetree/bindings/hwmon/sht15.txt b/Documentation/devicetree/bindings/hwmon/sht15.txt new file mode 100644 index 000000000000..6a80277cc426 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/sht15.txt @@ -0,0 +1,19 @@ +Sensirion SHT15 Humidity and Temperature Sensor + +Required properties: + + - "compatible": must be "sensirion,sht15". + - "data-gpios": GPIO connected to the data line. + - "clk-gpios": GPIO connected to the clock line. + - "vcc-supply": regulator that drives the VCC pin. + +Example: + + sensor { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sensor>; + compatible = "sensirion,sht15"; + clk-gpios = <&gpio4 12 0>; + data-gpios = <&gpio4 13 0>; + vcc-supply = <®_sht15>; + }; diff --git a/Documentation/devicetree/bindings/hwmon/stts751.txt b/Documentation/devicetree/bindings/hwmon/stts751.txt new file mode 100644 index 000000000000..3ee1dc30e72f --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/stts751.txt @@ -0,0 +1,15 @@ +* STTS751 thermometer. + +Required node properties: +- compatible: "stts751" +- reg: I2C bus address of the device + +Optional properties: +- smbus-timeout-disable: when set, the smbus timeout function will be disabled + +Example stts751 node: + +temp-sensor { + compatible = "stts751"; + reg = <0x48>; +} diff --git a/Documentation/devicetree/bindings/hwmon/tmp108.txt b/Documentation/devicetree/bindings/hwmon/tmp108.txt new file mode 100644 index 000000000000..8c4b10df86d9 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/tmp108.txt @@ -0,0 +1,14 @@ +TMP108 temperature sensor +------------------------- + +This device supports I2C only. + +Requires node properties: +- compatible : "ti,tmp108" +- reg : the I2C address of the device. This is 0x48, 0x49, 0x4a, or 0x4b. + +Example: + tmp108@48 { + compatible = "ti,tmp108"; + reg = <0x48>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt b/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt new file mode 100644 index 000000000000..70c054a9a997 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt @@ -0,0 +1,20 @@ +* Freescale Low Power Inter IC (LPI2C) for i.MX + +Required properties: +- compatible : + - "fsl,imx7ulp-lpi2c" for LPI2C compatible with the one integrated on i.MX7ULP soc + - "fsl,imx8dv-lpi2c" for LPI2C compatible with the one integrated on i.MX8DV soc +- reg : address and length of the lpi2c master registers +- interrupt-parent : core interrupt controller +- interrupts : lpi2c interrupt +- clocks : lpi2c clock specifier + +Examples: + +lpi2c7: lpi2c7@40A50000 { + compatible = "fsl,imx8dv-lpi2c"; + reg = <0x40A50000 0x10000>; + interrupt-parent = <&intc>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7ULP_CLK_LPI2C7>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt index cf53d5fba20a..aa097045a10e 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt @@ -19,7 +19,14 @@ Optional Properties: - i2c-mux-idle-disconnect: Boolean; if defined, forces mux to disconnect all children in idle state. This is necessary for example, if there are several multiplexers on the bus and the devices behind them use same I2C addresses. - + - interrupt-parent: Phandle for the interrupt controller that services + interrupts for this device. + - interrupts: Interrupt mapping for IRQ. + - interrupt-controller: Marks the device node as an interrupt controller. + - #interrupt-cells : Should be two. + - first cell is the pin number + - second cell is used to specify flags. + See also Documentation/devicetree/bindings/interrupt-controller/interrupts.txt Example: @@ -29,6 +36,11 @@ Example: #size-cells = <0>; reg = <0x74>; + interrupt-parent = <&ipic>; + interrupts = <17 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + i2c@2 { #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/i2c/i2c-pxa.txt b/Documentation/devicetree/bindings/i2c/i2c-pxa.txt index 12b78ac507e9..d30f0b11d853 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-pxa.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-pxa.txt @@ -7,6 +7,7 @@ Required properties : compatible processor, e.g. pxa168, pxa910, mmp2, mmp3. For the pxa2xx/pxa3xx, an additional node "mrvl,pxa-i2c" is required as shown in the example below. + For the Armada 3700, the compatible should be "marvell,armada-3700-i2c". Recommended properties : diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt index 239632a0d709..2b8bd33dbf8d 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt @@ -1,17 +1,25 @@ I2C for R-Car platforms Required properties: -- compatible: Must be one of - "renesas,i2c-rcar" - "renesas,i2c-r8a7778" - "renesas,i2c-r8a7779" - "renesas,i2c-r8a7790" - "renesas,i2c-r8a7791" - "renesas,i2c-r8a7792" - "renesas,i2c-r8a7793" - "renesas,i2c-r8a7794" - "renesas,i2c-r8a7795" - "renesas,i2c-r8a7796" +- compatible: + "renesas,i2c-r8a7778" if the device is a part of a R8A7778 SoC. + "renesas,i2c-r8a7779" if the device is a part of a R8A7779 SoC. + "renesas,i2c-r8a7790" if the device is a part of a R8A7790 SoC. + "renesas,i2c-r8a7791" if the device is a part of a R8A7791 SoC. + "renesas,i2c-r8a7792" if the device is a part of a R8A7792 SoC. + "renesas,i2c-r8a7793" if the device is a part of a R8A7793 SoC. + "renesas,i2c-r8a7794" if the device is a part of a R8A7794 SoC. + "renesas,i2c-r8a7795" if the device is a part of a R8A7795 SoC. + "renesas,i2c-r8a7796" if the device is a part of a R8A7796 SoC. + "renesas,rcar-gen1-i2c" for a generic R-Car Gen1 compatible device. + "renesas,rcar-gen2-i2c" for a generic R-Car Gen2 compatible device. + "renesas,rcar-gen3-i2c" for a generic R-Car Gen3 compatible device. + "renesas,i2c-rcar" (deprecated) + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first followed + by the generic version. + - reg: physical base address of the controller and length of memory mapped region. - interrupts: interrupt specifier. @@ -33,7 +41,7 @@ Examples : i2c0: i2c@e6508000 { #address-cells = <1>; #size-cells = <0>; - compatible = "renesas,i2c-r8a7791"; + compatible = "renesas,i2c-r8a7791", "renesas,rcar-gen2-i2c"; reg = <0 0xe6508000 0 0x40>; interrupts = <0 287 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp9_clks R8A7791_CLK_I2C0>; diff --git a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt index 214f94c25d37..ae9c2a735f39 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt @@ -1,8 +1,7 @@ Device tree configuration for Renesas IIC (sh_mobile) driver Required properties: -- compatible : "renesas,iic-<soctype>". "renesas,rmobile-iic" as fallback - Examples with soctypes are: +- compatible : - "renesas,iic-r8a73a4" (R-Mobile APE6) - "renesas,iic-r8a7740" (R-Mobile A1) - "renesas,iic-r8a7790" (R-Car H2) @@ -11,7 +10,19 @@ Required properties: - "renesas,iic-r8a7793" (R-Car M2-N) - "renesas,iic-r8a7794" (R-Car E2) - "renesas,iic-r8a7795" (R-Car H3) + - "renesas,iic-r8a7796" (R-Car M3-W) - "renesas,iic-sh73a0" (SH-Mobile AG5) + - "renesas,rcar-gen2-iic" (generic R-Car Gen2 compatible device) + - "renesas,rcar-gen3-iic" (generic R-Car Gen3 compatible device) + - "renesas,rmobile-iic" (generic device) + + When compatible with a generic R-Car version, nodes + must list the SoC-specific version corresponding to + the platform first followed by the generic R-Car + version. + + renesas,rmobile-iic must always follow. + - reg : address start and address range size of device - interrupts : interrupt of device - clocks : clock for device @@ -31,7 +42,8 @@ Pinctrl properties might be needed, too. See there. Example: iic0: i2c@e6500000 { - compatible = "renesas,iic-r8a7790", "renesas,rmobile-iic"; + compatible = "renesas,iic-r8a7790", "renesas,rcar-gen2-iic", + "renesas,rmobile-iic"; reg = <0 0xe6500000 0 0x425>; interrupts = <0 174 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7790_CLK_IIC0>; diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt new file mode 100644 index 000000000000..78eaf7b718ed --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt @@ -0,0 +1,33 @@ +* I2C controller embedded in STMicroelectronics STM32 I2C platform + +Required properties : +- compatible : Must be "st,stm32f4-i2c" +- reg : Offset and length of the register set for the device +- interrupts : Must contain the interrupt id for I2C event and then the + interrupt id for I2C error. +- resets: Must contain the phandle to the reset controller. +- clocks: Must contain the input clock of the I2C instance. +- A pinctrl state named "default" must be defined to set pins in mode of + operation for I2C transfer +- #address-cells = <1>; +- #size-cells = <0>; + +Optional properties : +- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, + the default 100 kHz frequency will be used. As only Normal and Fast modes + are supported, possible values are 100000 and 400000. + +Example : + + i2c@40005400 { + compatible = "st,stm32f4-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x40005400 0x400>; + interrupts = <31>, + <32>; + resets = <&rcc 277>; + clocks = <&rcc 0 149>; + pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>; + pinctrl-names = "default"; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c.txt b/Documentation/devicetree/bindings/i2c/i2c.txt index 5fa691e6f638..cee9d5055fa2 100644 --- a/Documentation/devicetree/bindings/i2c/i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c.txt @@ -62,6 +62,9 @@ wants to support one of the below features, it should adapt the bindings below. "irq" and "wakeup" names are recognized by I2C core, other names are left to individual drivers. +- host-notify + device uses SMBus host notify protocol instead of interrupt line. + - multi-master states that there is another master active on this bus. The OS can use this information to adapt power management to keep the arbitration awake @@ -81,6 +84,11 @@ Binding may contain optional "interrupts" property, describing interrupts used by the device. I2C core will assign "irq" interrupt (or the very first interrupt if not using interrupt names) as primary interrupt for the slave. +Alternatively, devices supporting SMbus Host Notify, and connected to +adapters that support this feature, may use "host-notify" property. I2C +core will create a virtual interrupt for Host Notify and assign it as +primary interrupt for the slave. + Also, if device is marked as a wakeup source, I2C core will set up "wakeup" interrupt for the device. If "wakeup" interrupt name is not present in the binding, then primary interrupt will be used as wakeup interrupt. diff --git a/Documentation/devicetree/bindings/i2c/nvidia,tegra186-bpmp-i2c.txt b/Documentation/devicetree/bindings/i2c/nvidia,tegra186-bpmp-i2c.txt new file mode 100644 index 000000000000..ab240e10debc --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/nvidia,tegra186-bpmp-i2c.txt @@ -0,0 +1,42 @@ +NVIDIA Tegra186 BPMP I2C controller + +In Tegra186, the BPMP (Boot and Power Management Processor) owns certain HW +devices, such as the I2C controller for the power management I2C bus. Software +running on other CPUs must perform IPC to the BPMP in order to execute +transactions on that I2C bus. This binding describes an I2C bus that is +accessed in such a fashion. + +The BPMP I2C node must be located directly inside the main BPMP node. See +../firmware/nvidia,tegra186-bpmp.txt for details of the BPMP binding. + +This node represents an I2C controller. See ../i2c/i2c.txt for details of the +core I2C binding. + +Required properties: +- compatible: + Array of strings. + One of: + - "nvidia,tegra186-bpmp-i2c". +- #address-cells: Address cells for I2C device address. + Single-cell integer. + Must be <1>. +- #size-cells: + Single-cell integer. + Must be <0>. +- nvidia,bpmp-bus-id: + Single-cell integer. + Indicates the I2C bus number this DT node represent, as defined by the + BPMP firmware. + +Example: + +bpmp { + ... + + i2c { + compatible = "nvidia,tegra186-bpmp-i2c"; + #address-cells = <1>; + #size-cells = <0>; + nvidia,bpmp-bus-id = <5>; + }; +}; diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index fbbad6446741..ad10fbe61562 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -36,14 +36,17 @@ dallas,ds1775 Tiny Digital Thermometer and Thermostat dallas,ds3232 Extremely Accurate I²C RTC with Integrated Crystal and SRAM dallas,ds4510 CPU Supervisor with Nonvolatile Memory and Programmable I/O dallas,ds75 Digital Thermometer and Thermostat +devantech,srf08 Devantech SRF08 ultrasonic ranger dlg,da9053 DA9053: flexible system level PMIC with multicore support dlg,da9063 DA9063: system PMIC for quad-core application processors domintech,dmard09 DMARD09: 3-axis Accelerometer +domintech,dmard10 DMARD10: 3-axis Accelerometer epson,rx8010 I2C-BUS INTERFACE REAL TIME CLOCK MODULE epson,rx8025 High-Stability. I2C-Bus INTERFACE REAL TIME CLOCK MODULE epson,rx8581 I2C-BUS INTERFACE REAL TIME CLOCK MODULE fsl,mag3110 MAG3110: Xtrinsic High Accuracy, 3D Magnetometer fsl,mc13892 MC13892: Power Management Integrated Circuit (PMIC) for i.MX35/51 +fsl,mma7660 MMA7660FC: 3-Axis Orientation/Motion Detection Sensor fsl,mma8450 MMA8450Q: Xtrinsic Low-power, 3-axis Xtrinsic Accelerometer fsl,mpl3115 MPL3115: Absolute Digital Pressure Sensor fsl,mpr121 MPR121: Proximity Capacitive Touch Sensor Controller @@ -57,6 +60,7 @@ maxim,max1237 Low-Power, 4-/12-Channel, 2-Wire Serial, 12-Bit ADCs maxim,max6625 9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface mc,rv3029c2 Real Time Clock Module with I2C-Bus mcube,mc3230 mCube 3-axis 8-bit digital accelerometer +memsic,mxc6225 MEMSIC 2-axis 8-bit digital accelerometer microchip,mcp4531-502 Microchip 7-bit Single I2C Digital Potentiometer (5k) microchip,mcp4531-103 Microchip 7-bit Single I2C Digital Potentiometer (10k) microchip,mcp4531-503 Microchip 7-bit Single I2C Digital Potentiometer (50k) @@ -121,6 +125,11 @@ microchip,mcp4662-502 Microchip 8-bit Dual I2C Digital Potentiometer with NV Mem microchip,mcp4662-103 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (10k) microchip,mcp4662-503 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (50k) microchip,mcp4662-104 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (100k) +microchip,tc654 PWM Fan Speed Controller With Fan Fault Detection +microchip,tc655 PWM Fan Speed Controller With Fan Fault Detection +miramems,da226 MiraMEMS DA226 2-axis 14-bit digital accelerometer +miramems,da280 MiraMEMS DA280 3-axis 14-bit digital accelerometer +miramems,da311 MiraMEMS DA311 3-axis 12-bit digital accelerometer national,lm63 Temperature sensor with integrated fan control national,lm75 I2C TEMP SENSOR national,lm80 Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor @@ -130,6 +139,8 @@ nuvoton,npct501 i2c trusted platform module (TPM) nuvoton,npct601 i2c trusted platform module (TPM2) nxp,pca9556 Octal SMBus and I2C registered interface nxp,pca9557 8-bit I2C-bus and SMBus I/O port with reset +nxp,pcf2127 Real-time clock +nxp,pcf2129 Real-time clock nxp,pcf8563 Real-time clock/calendar nxp,pcf85063 Tiny Real-Time Clock oki,ml86v7667 OKI ML86V7667 video decoder @@ -146,6 +157,7 @@ ricoh,rv5c387a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC samsung,24ad0xd1 S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power) sgx,vz89x SGX Sensortech VZ89X Sensors sii,s35390a 2-wire CMOS real-time clock +silabs,si7020 Relative Humidity and Temperature Sensors skyworks,sky81452 Skyworks SKY81452: Six-Channel White LED Driver with Touch Panel Bias Supply st,24c256 i2c serial eeprom (24cxx) st,m41t00 Serial real-time clock (RTC) @@ -158,4 +170,5 @@ ti,tsc2003 I2C Touch-Screen Controller ti,tmp102 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface ti,tmp103 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface ti,tmp275 Digital Temperature Sensor +winbond,w83793 Winbond/Nuvoton H/W Monitor winbond,wpct301 i2c trusted platform module (TPM) diff --git a/Documentation/devicetree/bindings/iio/accel/lis302.txt b/Documentation/devicetree/bindings/iio/accel/lis302.txt index 2a19bff9693f..dfdce67826ba 100644 --- a/Documentation/devicetree/bindings/iio/accel/lis302.txt +++ b/Documentation/devicetree/bindings/iio/accel/lis302.txt @@ -5,7 +5,7 @@ that apply in on the generic device (independent from the bus). Required properties for the SPI bindings: - - compatible: should be set to "st,lis3lv02d_spi" + - compatible: should be set to "st,lis3lv02d-spi" - reg: the chipselect index - spi-max-frequency: maximal bus speed, should be set to 1000000 unless constrained by external circuitry diff --git a/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt new file mode 100644 index 000000000000..f9e3ff2c656e --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt @@ -0,0 +1,32 @@ +* Amlogic Meson SAR (Successive Approximation Register) A/D converter + +Required properties: +- compatible: depending on the SoC this should be one of: + - "amlogic,meson-gxbb-saradc" for GXBB + - "amlogic,meson-gxl-saradc" for GXL + - "amlogic,meson-gxm-saradc" for GXM + along with the generic "amlogic,meson-saradc" +- reg: the physical base address and length of the registers +- clocks: phandle and clock identifier (see clock-names) +- clock-names: mandatory clocks: + - "clkin" for the reference clock (typically XTAL) + - "core" for the SAR ADC core clock + optional clocks: + - "sana" for the analog clock + - "adc_clk" for the ADC (sampling) clock + - "adc_sel" for the ADC (sampling) clock mux +- vref-supply: the regulator supply for the ADC reference voltage +- #io-channel-cells: must be 1, see ../iio-bindings.txt + +Example: + saradc: adc@8680 { + compatible = "amlogic,meson-gxl-saradc", "amlogic,meson-saradc"; + #io-channel-cells = <1>; + reg = <0x0 0x8680 0x0 0x34>; + clocks = <&xtal>, + <&clkc CLKID_SAR_ADC>, + <&clkc CLKID_SANA>, + <&clkc CLKID_SAR_ADC_CLK>, + <&clkc CLKID_SAR_ADC_SEL>; + clock-names = "clkin", "core", "sana", "adc_clk", "adc_sel"; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/avia-hx711.txt b/Documentation/devicetree/bindings/iio/adc/avia-hx711.txt new file mode 100644 index 000000000000..b3629405f568 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/avia-hx711.txt @@ -0,0 +1,18 @@ +* AVIA HX711 ADC chip for weight cells + Bit-banging driver + +Required properties: + - compatible: Should be "avia,hx711" + - sck-gpios: Definition of the GPIO for the clock + - dout-gpios: Definition of the GPIO for data-out + See Documentation/devicetree/bindings/gpio/gpio.txt + - avdd-supply: Definition of the regulator used as analog supply + +Example: +weight@0 { + compatible = "avia,hx711"; + sck-gpios = <&gpio3 10 GPIO_ACTIVE_HIGH>; + dout-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; + avdd-suppy = <&avdd>; +}; + diff --git a/Documentation/devicetree/bindings/iio/adc/envelope-detector.txt b/Documentation/devicetree/bindings/iio/adc/envelope-detector.txt new file mode 100644 index 000000000000..27544bdd4478 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/envelope-detector.txt @@ -0,0 +1,54 @@ +Bindings for ADC envelope detector using a DAC and a comparator + +The DAC is used to find the peak level of an alternating voltage input +signal by a binary search using the output of a comparator wired to +an interrupt pin. Like so: + _ + | \ + input +------>-------|+ \ + | \ + .-------. | }---. + | | | / | + | dac|-->--|- / | + | | |_/ | + | | | + | | | + | irq|------<-------' + | | + '-------' + +Required properties: +- compatible: Should be "axentia,tse850-envelope-detector" +- io-channels: Channel node of the dac to be used for comparator input. +- io-channel-names: Should be "dac". +- interrupt specification for one client interrupt, + see ../../interrupt-controller/interrupts.txt for details. +- interrupt-names: Should be "comp". + +Example: + + &i2c { + dpot: mcp4651-104@28 { + compatible = "microchip,mcp4651-104"; + reg = <0x28>; + #io-channel-cells = <1>; + }; + }; + + dac: dac { + compatible = "dpot-dac"; + vref-supply = <®_3v3>; + io-channels = <&dpot 0>; + io-channel-names = "dpot"; + #io-channel-cells = <1>; + }; + + envelope-detector { + compatible = "axentia,tse850-envelope-detector"; + io-channels = <&dac 0>; + io-channel-names = "dac"; + + interrupt-parent = <&gpio>; + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + interrupt-names = "comp"; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/max11100.txt b/Documentation/devicetree/bindings/iio/adc/max11100.txt new file mode 100644 index 000000000000..b7f7177b8aca --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/max11100.txt @@ -0,0 +1,18 @@ +* Maxim max11100 Analog to Digital Converter (ADC) + +Required properties: + - compatible: Should be "maxim,max11100" + - reg: the adc unit address + - vref-supply: phandle to the regulator that provides reference voltage + +Optional properties: + - spi-max-frequency: SPI maximum frequency + +Example: + +max11100: adc@0 { + compatible = "maxim,max11100"; + reg = <0>; + vref-supply = <&adc0_vref>; + spi-max-frequency = <240000>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,pm8xxx-xoadc.txt b/Documentation/devicetree/bindings/iio/adc/qcom,pm8xxx-xoadc.txt new file mode 100644 index 000000000000..53cd146d8096 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/qcom,pm8xxx-xoadc.txt @@ -0,0 +1,149 @@ +Qualcomm's PM8xxx voltage XOADC + +The Qualcomm PM8xxx PMICs contain a HK/XO ADC (Housekeeping/Crystal +oscillator ADC) encompassing PM8018, PM8038, PM8058 and PM8921. + +Required properties: + +- compatible: should be one of: + "qcom,pm8018-adc" + "qcom,pm8038-adc" + "qcom,pm8058-adc" + "qcom,pm8921-adc" + +- reg: should contain the ADC base address in the PMIC, typically + 0x197. + +- xoadc-ref-supply: should reference a regulator that can supply + a reference voltage on demand. The reference voltage may vary + with PMIC variant but is typically something like 2.2 or 1.8V. + +The following required properties are standard for IO channels, see +iio-bindings.txt for more details: + +- #address-cells: should be set to <1> + +- #size-cells: should be set to <0> + +- #io-channel-cells: should be set to <1> + +- interrupts: should refer to the parent PMIC interrupt controller + and reference the proper ADC interrupt. + +Required subnodes: + +The ADC channels are configured as subnodes of the ADC. Since some of +them are used for calibrating the ADC, these nodes are compulsory: + +adc-channel@c { + reg = <0x0c>; +}; + +adc-channel@d { + reg = <0x0d>; +}; + +adc-channel@f { + reg = <0x0f>; +}; + +These three nodes are used for absolute and ratiometric calibration +and only need to have these reg values: they are by hardware definition +1:1 ratio converters that sample 625, 1250 and 0 milliV and create +an interpolation calibration for all other ADCs. + +Optional subnodes: any channels other than channel 0x0c, 0x0d and +0x0f are optional. + +Required channel node properties: + +- reg: should contain the hardware channel number in the range + 0 .. 0x0f (4 bits). The hardware only supports 16 channels. + +Optional channel node properties: + +- qcom,decimation: + Value type: <u32> + Definition: This parameter is used to decrease the ADC sampling rate. + Quicker measurements can be made by reducing the decimation ratio. + Valid values are 512, 1024, 2048, 4096. + If the property is not found, a default value of 512 will be used. + +- qcom,ratiometric: + Value type: <u32> + Definition: Channel calibration type. If this property is specified + VADC will use a special voltage references for channel + calibration. The available references are specified in the + as a u32 value setting (see below) and it is compulsory + to also specify this reference if ratiometric calibration + is selected. + + If the property is not found, the channel will be + calibrated with the 0.625V and 1.25V reference channels, also + known as an absolute calibration. + The reference voltage pairs when using ratiometric calibration: + 0 = XO_IN/XOADC_GND + 1 = PMIC_IN/XOADC_GND + 2 = PMIC_IN/BMS_CSP + 3 (invalid) + 4 = XOADC_GND/XOADC_GND + 5 = XOADC_VREF/XOADC_GND + +Example: + +xoadc: xoadc@197 { + compatible = "qcom,pm8058-adc"; + reg = <0x197>; + interrupt-parent = <&pm8058>; + interrupts = <76 1>; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + + vcoin: adc-channel@0 { + reg = <0x00>; + }; + vbat: adc-channel@1 { + reg = <0x01>; + }; + dcin: adc-channel@2 { + reg = <0x02>; + }; + ichg: adc-channel@3 { + reg = <0x03>; + }; + vph_pwr: adc-channel@4 { + reg = <0x04>; + }; + usb_vbus: adc-channel@a { + reg = <0x0a>; + }; + die_temp: adc-channel@b { + reg = <0x0b>; + }; + ref_625mv: adc-channel@c { + reg = <0x0c>; + }; + ref_1250mv: adc-channel@d { + reg = <0x0d>; + }; + ref_325mv: adc-channel@e { + reg = <0x0e>; + }; + ref_muxoff: adc-channel@f { + reg = <0x0f>; + }; +}; + + +/* IIO client node */ +iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&xoadc 0x01>, /* Battery */ + <&xoadc 0x02>, /* DC in (charger) */ + <&xoadc 0x04>, /* VPH the main system voltage */ + <&xoadc 0x0b>, /* Die temperature */ + <&xoadc 0x0c>, /* Reference voltage 1.25V */ + <&xoadc 0x0d>, /* Reference voltage 0.625V */ + <&xoadc 0x0e>; /* Reference voltage 0.325V */ +}; diff --git a/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt b/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt new file mode 100644 index 000000000000..f5b0adae6010 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt @@ -0,0 +1,99 @@ +* Renesas RCar GyroADC device driver + +The GyroADC block is a reduced SPI block with up to 8 chipselect lines, +which supports the SPI protocol of a selected few SPI ADCs. The SPI ADCs +are sampled by the GyroADC block in a round-robin fashion and the result +presented in the GyroADC registers. + +Required properties: +- compatible: Should be "<soc-specific>", "renesas,rcar-gyroadc". + The <soc-specific> should be one of: + renesas,r8a7791-gyroadc - for the GyroADC block present + in r8a7791 SoC + renesas,r8a7792-gyroadc - for the GyroADC with interrupt + block present in r8a7792 SoC +- reg: Address and length of the register set for the device +- clocks: References to all the clocks specified in the clock-names + property as specified in + Documentation/devicetree/bindings/clock/clock-bindings.txt. +- clock-names: Shall contain "fck" and "if". The "fck" is the GyroADC block + clock, the "if" is the interface clock. +- power-domains: Must contain a reference to the PM domain, if available. +- #address-cells: Should be <1> (setting for the subnodes) for all ADCs + except for "fujitsu,mb88101a". Should be <0> (setting for + only subnode) for "fujitsu,mb88101a". +- #size-cells: Should be <0> (setting for the subnodes) + +Sub-nodes: +You must define subnode(s) which select the connected ADC type and reference +voltage for the GyroADC channels. + +Required properties for subnodes: +- compatible: Should be either of: + "fujitsu,mb88101a" + - Fujitsu MB88101A compatible mode, + 12bit sampling, up to 4 channels can be sampled in + round-robin fashion. One Fujitsu chip supplies four + GyroADC channels with data as it contains four ADCs + on the chip and thus for 4-channel operation, single + MB88101A is required. The Cx chipselect lines of the + MB88101A connect directly to two CHS lines of the + GyroADC, no demuxer is required. The data out line + of each MB88101A connects to a shared input pin of + the GyroADC. + "ti,adcs7476" or "ti,adc121" or "adi,ad7476" + - TI ADCS7476 / TI ADC121 / ADI AD7476 compatible mode, + 15bit sampling, up to 8 channels can be sampled in + round-robin fashion. One TI/ADI chip supplies single + ADC channel with data, thus for 8-channel operation, + 8 chips are required. A 3:8 chipselect demuxer is + required to connect the nCS line of the TI/ADI chips + to the GyroADC, while MISO line of each TI/ADI ADC + connects to a shared input pin of the GyroADC. + "maxim,max1162" or "maxim,max11100" + - Maxim MAX1162 / Maxim MAX11100 compatible mode, + 16bit sampling, up to 8 channels can be sampled in + round-robin fashion. One Maxim chip supplies single + ADC channel with data, thus for 8-channel operation, + 8 chips are required. A 3:8 chipselect demuxer is + required to connect the nCS line of the MAX chips + to the GyroADC, while MISO line of each Maxim ADC + connects to a shared input pin of the GyroADC. +- reg: Should be the number of the analog input. Should be present + for all ADCs except "fujitsu,mb88101a". +- vref-supply: Reference to the channel reference voltage regulator. + +Example: + vref_max1162: regulator-vref-max1162 { + compatible = "regulator-fixed"; + + regulator-name = "MAX1162 Vref"; + regulator-min-microvolt = <4096000>; + regulator-max-microvolt = <4096000>; + }; + + adc@e6e54000 { + compatible = "renesas,r8a7791-gyroadc", "renesas,rcar-gyroadc"; + reg = <0 0xe6e54000 0 64>; + clocks = <&mstp9_clks R8A7791_CLK_GYROADC>, <&clk_65m>; + clock-names = "fck", "if"; + power-domains = <&sysc R8A7791_PD_ALWAYS_ON>; + + pinctrl-0 = <&adc_pins>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + reg = <0>; + compatible = "maxim,max1162"; + vref-supply = <&vref_max1162>; + }; + + adc@1 { + reg = <1>; + compatible = "maxim,max1162"; + vref-supply = <&vref_max1162>; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt new file mode 100644 index 000000000000..5dfc88ec24a4 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt @@ -0,0 +1,90 @@ +STMicroelectronics STM32 ADC device driver + +STM32 ADC is a successive approximation analog-to-digital converter. +It has several multiplexed input channels. Conversions can be performed +in single, continuous, scan or discontinuous mode. Result of the ADC is +stored in a left-aligned or right-aligned 32-bit data register. +Conversions can be launched in software or using hardware triggers. + +The analog watchdog feature allows the application to detect if the input +voltage goes beyond the user-defined, higher or lower thresholds. + +Each STM32 ADC block can have up to 3 ADC instances. + +Each instance supports two contexts to manage conversions, each one has its +own configurable sequence and trigger: +- regular conversion can be done in sequence, running in background +- injected conversions have higher priority, and so have the ability to + interrupt regular conversion sequence (either triggered in SW or HW). + Regular sequence is resumed, in case it has been interrupted. + +Contents of a stm32 adc root node: +----------------------------------- +Required properties: +- compatible: Should be "st,stm32f4-adc-core". +- reg: Offset and length of the ADC block register set. +- interrupts: Must contain the interrupt for ADC block. +- clocks: Clock for the analog circuitry (common to all ADCs). +- clock-names: Must be "adc". +- interrupt-controller: Identifies the controller node as interrupt-parent +- vref-supply: Phandle to the vref input analog reference voltage. +- #interrupt-cells = <1>; +- #address-cells = <1>; +- #size-cells = <0>; + +Optional properties: +- A pinctrl state named "default" for each ADC channel may be defined to set + inX ADC pins in mode of operation for analog input on external pin. + +Contents of a stm32 adc child node: +----------------------------------- +An ADC block node should contain at least one subnode, representing an +ADC instance available on the machine. + +Required properties: +- compatible: Should be "st,stm32f4-adc". +- reg: Offset of ADC instance in ADC block (e.g. may be 0x0, 0x100, 0x200). +- clocks: Input clock private to this ADC instance. +- interrupt-parent: Phandle to the parent interrupt controller. +- interrupts: IRQ Line for the ADC (e.g. may be 0 for adc@0, 1 for adc@100 or + 2 for adc@200). +- st,adc-channels: List of single-ended channels muxed for this ADC. + It can have up to 16 channels, numbered from 0 to 15 (resp. for in0..in15). +- #io-channel-cells = <1>: See the IIO bindings section "IIO consumers" in + Documentation/devicetree/bindings/iio/iio-bindings.txt + +Optional properties: +- dmas: Phandle to dma channel for this ADC instance. + See ../../dma/dma.txt for details. +- dma-names: Must be "rx" when dmas property is being used. + +Example: + adc: adc@40012000 { + compatible = "st,stm32f4-adc-core"; + reg = <0x40012000 0x400>; + interrupts = <18>; + clocks = <&rcc 0 168>; + clock-names = "adc"; + vref-supply = <®_vref>; + interrupt-controller; + pinctrl-names = "default"; + pinctrl-0 = <&adc3_in8_pin>; + + #interrupt-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + compatible = "st,stm32f4-adc"; + #io-channel-cells = <1>; + reg = <0x0>; + clocks = <&rcc 0 168>; + interrupt-parent = <&adc>; + interrupts = <0>; + st,adc-channels = <8>; + dmas = <&dma2 0 0 0x400 0x0>; + dma-names = "rx"; + }; + ... + other adc child nodes follow... + }; diff --git a/Documentation/devicetree/bindings/iio/adc/ti-adc161s626.txt b/Documentation/devicetree/bindings/iio/adc/ti-adc161s626.txt index 9ed2315781e4..3d25011f0c99 100644 --- a/Documentation/devicetree/bindings/iio/adc/ti-adc161s626.txt +++ b/Documentation/devicetree/bindings/iio/adc/ti-adc161s626.txt @@ -3,6 +3,7 @@ Required properties: - compatible: Should be "ti,adc141s626" or "ti,adc161s626" - reg: spi chip select number for the device + - vdda-supply: supply voltage to VDDA pin Recommended properties: - spi-max-frequency: Definition as per @@ -11,6 +12,7 @@ Recommended properties: Example: adc@0 { compatible = "ti,adc161s626"; + vdda-supply = <&vdda_fixed>; reg = <0>; spi-max-frequency = <4300000>; }; diff --git a/Documentation/devicetree/bindings/iio/adc/ti-ads7950.txt b/Documentation/devicetree/bindings/iio/adc/ti-ads7950.txt new file mode 100644 index 000000000000..e77a6f7e1001 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti-ads7950.txt @@ -0,0 +1,23 @@ +* Texas Instruments ADS7950 family of A/DC chips + +Required properties: + - compatible: Must be one of "ti,ads7950", "ti,ads7951", "ti,ads7952", + "ti,ads7953", "ti,ads7954", "ti,ads7955", "ti,ads7956", "ti,ads7957", + "ti,ads7958", "ti,ads7959", "ti,ads7960", or "ti,ads7961" + - reg: SPI chip select number for the device + - #io-channel-cells: Must be 1 as per ../iio-bindings.txt + - vref-supply: phandle to a regulator node that supplies the 2.5V or 5V + reference voltage + +Recommended properties: + - spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: +adc@0 { + compatible = "ti,ads7957"; + reg = <0>; + #io-channel-cells = <1>; + vref-supply = <&refin_supply>; + spi-max-frequency = <10000000>; +}; diff --git a/Documentation/devicetree/bindings/iio/dac/dpot-dac.txt b/Documentation/devicetree/bindings/iio/dac/dpot-dac.txt new file mode 100644 index 000000000000..fdf47a01bfef --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/dpot-dac.txt @@ -0,0 +1,41 @@ +Bindings for DAC emulation using a digital potentiometer + +It is assumed that the dpot is used as a voltage divider between the +current dpot wiper setting and the maximum resistance of the dpot. The +divided voltage is provided by a vref regulator. + + .------. + .-----------. | | + | vref |--' .---. + | regulator |--. | | + '-----------' | | d | + | | p | + | | o | wiper + | | t |<---------+ + | | | + | '---' dac output voltage + | | + '------+------------+ + +Required properties: +- compatible: Should be "dpot-dac" +- vref-supply: The regulator supplying the voltage divider. +- io-channels: Channel node of the dpot to be used for the voltage division. +- io-channel-names: Should be "dpot". + +Example: + + &i2c { + dpot: mcp4651-503@28 { + compatible = "microchip,mcp4651-503"; + reg = <0x28>; + #io-channel-cells = <1>; + }; + }; + + dac { + compatible = "dpot-dac"; + vref-supply = <®_3v3>; + io-channels = <&dpot 0>; + io-channel-names = "dpot"; + }; diff --git a/Documentation/devicetree/bindings/iio/dac/mcp4725.txt b/Documentation/devicetree/bindings/iio/dac/mcp4725.txt new file mode 100644 index 000000000000..1bc6c093fbfe --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/mcp4725.txt @@ -0,0 +1,35 @@ +Microchip mcp4725 and mcp4726 DAC device driver + +Required properties: + - compatible: Must be "microchip,mcp4725" or "microchip,mcp4726" + - reg: Should contain the DAC I2C address + - vdd-supply: Phandle to the Vdd power supply. This supply is used as a + voltage reference on mcp4725. It is used as a voltage reference on + mcp4726 if there is no vref-supply specified. + +Optional properties (valid only for mcp4726): + - vref-supply: Optional phandle to the Vref power supply. Vref pin is + used as a voltage reference when this supply is specified. + - microchip,vref-buffered: Boolean to enable buffering of the external + Vref pin. This boolean is not valid without the vref-supply. Quoting + the datasheet: This is offered in cases where the reference voltage + does not have the current capability not to drop its voltage when + connected to the internal resistor ladder circuit. + +Examples: + + /* simple mcp4725 */ + mcp4725@60 { + compatible = "microchip,mcp4725"; + reg = <0x60>; + vdd-supply = <&vdac_vdd>; + }; + + /* mcp4726 with the buffered external reference voltage */ + mcp4726@60 { + compatible = "microchip,mcp4726"; + reg = <0x60>; + vdd-supply = <&vdac_vdd>; + vref-supply = <&vdac_vref>; + microchip,vref-buffered; + }; diff --git a/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.txt b/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.txt new file mode 100644 index 000000000000..b0d3b59966bc --- /dev/null +++ b/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.txt @@ -0,0 +1,46 @@ +Invensense MPU-3050 Gyroscope device tree bindings + +Required properties: + - compatible : should be "invensense,mpu3050" + - reg : the I2C address of the sensor + +Optional properties: + - interrupt-parent : should be the phandle for the interrupt controller + - interrupts : interrupt mapping for the trigger interrupt from the + internal oscillator. The following IRQ modes are supported: + IRQ_TYPE_EDGE_RISING, IRQ_TYPE_EDGE_FALLING, IRQ_TYPE_LEVEL_HIGH and + IRQ_TYPE_LEVEL_LOW. The driver should detect and configure the hardware + for the desired interrupt type. + - vdd-supply : supply regulator for the main power voltage. + - vlogic-supply : supply regulator for the signal voltage. + - mount-matrix : see iio/mount-matrix.txt + +Optional subnodes: + - The MPU-3050 will pass through and forward the I2C signals from the + incoming I2C bus, alternatively drive traffic to a slave device (usually + an accelerometer) on its own initiative. Therefore is supports a subnode + i2c gate node. For details see: i2c/i2c-gate.txt + +Example: + +mpu3050@68 { + compatible = "invensense,mpu3050"; + reg = <0x68>; + interrupt-parent = <&foo>; + interrupts = <12 IRQ_TYPE_EDGE_FALLING>; + vdd-supply = <&bar>; + vlogic-supply = <&baz>; + + /* External I2C interface */ + i2c-gate { + #address-cells = <1>; + #size-cells = <0>; + + fnord@18 { + compatible = "fnord"; + reg = <0x18>; + interrupt-parent = <&foo>; + interrupts = <13 IRQ_TYPE_EDGE_FALLING>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/iio/humidity/hts221.txt b/Documentation/devicetree/bindings/iio/humidity/hts221.txt new file mode 100644 index 000000000000..b20ab9c12080 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/humidity/hts221.txt @@ -0,0 +1,22 @@ +* HTS221 STM humidity + temperature sensor + +Required properties: +- compatible: should be "st,hts221" +- reg: i2c address of the sensor / spi cs line + +Optional properties: +- interrupt-parent: should be the phandle for the interrupt controller +- interrupts: interrupt mapping for IRQ. It should be configured with + flags IRQ_TYPE_LEVEL_HIGH or IRQ_TYPE_EDGE_RISING. + + Refer to interrupt-controller/interrupts.txt for generic interrupt + client node bindings. + +Example: + +hts221@5f { + compatible = "st,hts221"; + reg = <0x5f>; + interrupt-parent = <&gpio0>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>; +}; diff --git a/Documentation/devicetree/bindings/iio/imu/bmi160.txt b/Documentation/devicetree/bindings/iio/imu/bmi160.txt new file mode 100644 index 000000000000..ae0112c7debc --- /dev/null +++ b/Documentation/devicetree/bindings/iio/imu/bmi160.txt @@ -0,0 +1,36 @@ +Bosch BMI160 - Inertial Measurement Unit with Accelerometer, Gyroscope +and externally connectable Magnetometer + +https://www.bosch-sensortec.com/bst/products/all_products/bmi160 + +Required properties: + - compatible : should be "bosch,bmi160" + - reg : the I2C address or SPI chip select number of the sensor + - spi-max-frequency : set maximum clock frequency (only for SPI) + +Optional properties: + - interrupt-parent : should be the phandle of the interrupt controller + - interrupts : interrupt mapping for IRQ, must be IRQ_TYPE_LEVEL_LOW + - interrupt-names : set to "INT1" if INT1 pin should be used as interrupt + input, set to "INT2" if INT2 pin should be used instead + +Examples: + +bmi160@68 { + compatible = "bosch,bmi160"; + reg = <0x68>; + + interrupt-parent = <&gpio4>; + interrupts = <12 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "INT1"; +}; + +bmi160@0 { + compatible = "bosch,bmi160"; + reg = <0>; + spi-max-frequency = <10000000>; + + interrupt-parent = <&gpio2>; + interrupts = <12 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "INT2"; +}; diff --git a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt new file mode 100644 index 000000000000..cf81afdf7803 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt @@ -0,0 +1,26 @@ +* ST_LSM6DSx driver for STM 6-axis (acc + gyro) imu Mems sensors + +Required properties: +- compatible: must be one of: + "st,lsm6ds3" + "st,lsm6dsm" +- reg: i2c address of the sensor / spi cs line + +Optional properties: +- st,drdy-int-pin: the pin on the package that will be used to signal + "data ready" (valid values: 1 or 2). +- interrupt-parent: should be the phandle for the interrupt controller +- interrupts: interrupt mapping for IRQ. It should be configured with + flags IRQ_TYPE_LEVEL_HIGH or IRQ_TYPE_EDGE_RISING. + + Refer to interrupt-controller/interrupts.txt for generic interrupt + client node bindings. + +Example: + +lsm6dsm@6b { + compatible = "st,lsm6dsm"; + reg = <0x6b>; + interrupt-parent = <&gpio0>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>; +}; diff --git a/Documentation/devicetree/bindings/iio/light/cm3605.txt b/Documentation/devicetree/bindings/iio/light/cm3605.txt new file mode 100644 index 000000000000..56331a79f9ab --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/cm3605.txt @@ -0,0 +1,41 @@ +Capella Microsystems CM3605 +Ambient Light and Short Distance Proximity Sensor + +The CM3605 is an entirely analog part which however require quite a bit of +software logic to interface a host operating system. + +This ALS and proximity sensor was one of the very first deployed in mobile +handsets, notably it is used in the very first Nexus One Android phone from +2010. + +Required properties: +- compatible: must be: "capella,cm3605" +- aset-gpios: GPIO line controlling the ASET line (drive low + to activate the ALS, should be flagged GPIO_ACTIVE_LOW) +- interrupts: the IRQ line (such as a GPIO) that is connected to + the POUT (proximity sensor out) line. The edge detection must + be set to IRQ_TYPE_EDGE_BOTH so as to detect movements toward + and away from the proximity sensor. +- io-channels: the ADC channel used for converting the voltage from + AOUT to a digital representation. +- io-channel-names: must be "aout" + +Optional properties: +- vdd-supply: regulator supplying VDD power to the component. +- capella,aset-resistance-ohms: the sensitivity calibration resistance, + in Ohms. Valid values are: 50000, 100000, 300000 and 600000, + as these are the resistance values that we are supplied with + calibration curves for. If not supplied, 100 kOhm will be assumed + but it is strongly recommended to supply this. + +Example: + +cm3605 { + compatible = "capella,cm3605"; + vdd-supply = <&foo_reg>; + aset-gpios = <&foo_gpio 1 GPIO_ACTIVE_LOW>; + capella,aset-resistance-ohms = <100000>; + interrupts = <1 IRQ_TYPE_EDGE_BOTH>; + io-channels = <&adc 0x01>; + io-channel-names = "aout"; +}; diff --git a/Documentation/devicetree/bindings/iio/light/isl29018.txt b/Documentation/devicetree/bindings/iio/light/isl29018.txt new file mode 100644 index 000000000000..425ab459e209 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/isl29018.txt @@ -0,0 +1,28 @@ +* ISL 29018/29023/29035 I2C ALS, Proximity, and Infrared sensor + +Required properties: + + - compatible: Should be one of + "isil,isl29018" + "isil,isl29023" + "isil,isl29035" + - reg: the I2C address of the device + +Optional properties: + + - interrupt-parent: should be the phandle for the interrupt controller + - interrupts: the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic interrupt client + node bindings. + + - vcc-supply: phandle to the regulator that provides power to the sensor. + +Example: + +isl29018@44 { + compatible = "isil,isl29018"; + reg = <0x44>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(Z, 2) IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/iio/light/tsl2583.txt b/Documentation/devicetree/bindings/iio/light/tsl2583.txt new file mode 100644 index 000000000000..8e2066c83f70 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/tsl2583.txt @@ -0,0 +1,26 @@ +* TAOS TSL 2580/2581/2583 ALS sensor + +Required properties: + + - compatible: Should be one of + "amstaos,tsl2580" + "amstaos,tsl2581" + "amstaos,tsl2583" + - reg: the I2C address of the device + +Optional properties: + + - interrupt-parent: should be the phandle for the interrupt controller + - interrupts: the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic interrupt client + node bindings. + + - vcc-supply: phandle to the regulator that provides power to the sensor. + +Example: + +tsl2581@29 { + compatible = "amstaos,tsl2581"; + reg = <0x29>; +}; diff --git a/Documentation/devicetree/bindings/iio/potentiometer/max5481.txt b/Documentation/devicetree/bindings/iio/potentiometer/max5481.txt new file mode 100644 index 000000000000..6a91b106e076 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/potentiometer/max5481.txt @@ -0,0 +1,23 @@ +* Maxim Linear-Taper Digital Potentiometer MAX5481-MAX5484 + +The node for this driver must be a child node of a SPI controller, hence +all mandatory properties described in + + Documentation/devicetree/bindings/spi/spi-bus.txt + +must be specified. + +Required properties: + - compatible: Must be one of the following, depending on the + model: + "maxim,max5481" + "maxim,max5482" + "maxim,max5483" + "maxim,max5484" + +Example: +max548x: max548x@0 { + compatible = "maxim,max5482"; + spi-max-frequency = <7000000>; + reg = <0>; /* chip-select */ +}; diff --git a/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt b/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt new file mode 100644 index 000000000000..b9b621e94cd7 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt @@ -0,0 +1,30 @@ +* Texas Instruments LMP91000 potentiostat + +http://www.ti.com/lit/ds/symlink/lmp91000.pdf + +Required properties: + + - compatible: should be "ti,lmp91000" + - reg: the I2C address of the device + - io-channels: the phandle of the iio provider + + - ti,external-tia-resistor: if the property ti,tia-gain-ohm is not defined this + needs to be set to signal that an external resistor value is being used. + +Optional properties: + + - ti,tia-gain-ohm: ohm value of the internal resistor for the transimpedance + amplifier. Must be 2750, 3500, 7000, 14000, 35000, 120000, or 350000 ohms. + + - ti,rload-ohm: ohm value of the internal resistor load applied to the gas + sensor. Must be 10, 33, 50, or 100 (default) ohms. + +Example: + +lmp91000@48 { + compatible = "ti,lmp91000"; + reg = <0x48>; + ti,tia-gain-ohm = <7500>; + ti,rload = <100>; + io-channels = <&adc>; +}; diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt index e41fe340162b..eaa8fbba34e2 100644 --- a/Documentation/devicetree/bindings/iio/st-sensors.txt +++ b/Documentation/devicetree/bindings/iio/st-sensors.txt @@ -27,6 +27,8 @@ standard bindings from pinctrl/pinctrl-bindings.txt. Valid compatible strings: Accelerometers: +- st,lis3lv02d (deprecated, use st,lis3lv02dl-accel) +- st,lis302dl-spi (deprecated, use st,lis3lv02dl-accel) - st,lis3lv02dl-accel - st,lsm303dlh-accel - st,lsm303dlhc-accel @@ -42,6 +44,7 @@ Accelerometers: - st,lsm303agr-accel - st,lis2dh12-accel - st,h3lis331dl-accel +- st,lng2dm-accel Gyroscopes: - st,l3g4200d-gyro diff --git a/Documentation/devicetree/bindings/iio/temperature/tmp007.txt b/Documentation/devicetree/bindings/iio/temperature/tmp007.txt new file mode 100644 index 000000000000..b63aba91ef03 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/temperature/tmp007.txt @@ -0,0 +1,35 @@ +* TI TMP007 - IR thermopile sensor with integrated math engine + +Link to datasheet: http://www.ti.com/lit/ds/symlink/tmp007.pdf + +Required properties: + + - compatible: should be "ti,tmp007" + - reg: the I2C address of the sensor (changeable via ADR pins) + ------------------------------ + |ADR1 | ADR0 | Device Address| + ------------------------------ + 0 0 0x40 + 0 1 0x41 + 0 SDA 0x42 + 0 SCL 0x43 + 1 0 0x44 + 1 1 0x45 + 1 SDA 0x46 + 1 SCL 0x47 + +Optional properties: + + - interrupt-parent: should be the phandle for the interrupt controller + + - interrupts: interrupt mapping for GPIO IRQ (level active low) + +Example: + +tmp007@40 { + compatible = "ti,tmp007"; + reg = <0x40>; + interrupt-parent = <&gpio0>; + interrupts = <5 0x08>; +}; + diff --git a/Documentation/devicetree/bindings/iio/timer/stm32-timer-trigger.txt b/Documentation/devicetree/bindings/iio/timer/stm32-timer-trigger.txt new file mode 100644 index 000000000000..55a653d15303 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/timer/stm32-timer-trigger.txt @@ -0,0 +1,23 @@ +STMicroelectronics STM32 Timers IIO timer bindings + +Must be a sub-node of an STM32 Timers device tree node. +See ../mfd/stm32-timers.txt for details about the parent node. + +Required parameters: +- compatible: Must be "st,stm32-timer-trigger". +- reg: Identify trigger hardware block. + +Example: + timers@40010000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40010000 0x400>; + clocks = <&rcc 0 160>; + clock-names = "clk_int"; + + timer@0 { + compatible = "st,stm32-timer-trigger"; + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/cypress,tm2-touchkey.txt b/Documentation/devicetree/bindings/input/cypress,tm2-touchkey.txt new file mode 100644 index 000000000000..635f62c756ee --- /dev/null +++ b/Documentation/devicetree/bindings/input/cypress,tm2-touchkey.txt @@ -0,0 +1,27 @@ +Samsung tm2-touchkey + +Required properties: +- compatible: must be "cypress,tm2-touchkey" +- reg: I2C address of the chip. +- interrupt-parent: a phandle for the interrupt controller (see interrupt + binding[0]). +- interrupts: interrupt to which the chip is connected (see interrupt + binding[0]). +- vcc-supply : internal regulator output. 1.8V +- vdd-supply : power supply for IC 3.3V + +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + +Example: + &i2c0 { + /* ... */ + + touchkey@20 { + compatible = "cypress,tm2-touchkey"; + reg = <0x20>; + interrupt-parent = <&gpa3>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; + vcc-supply=<&ldo32_reg>; + vdd-supply=<&ldo33_reg>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/da9062-onkey.txt b/Documentation/devicetree/bindings/input/da9062-onkey.txt index ab0e0488fe92..5f9fbc68e58a 100644 --- a/Documentation/devicetree/bindings/input/da9062-onkey.txt +++ b/Documentation/devicetree/bindings/input/da9062-onkey.txt @@ -1,32 +1,47 @@ -* Dialog DA9062/63 OnKey Module +* Dialog DA9061/62/63 OnKey Module -This module is part of the DA9062/DA9063. For more details about entire -chips see Documentation/devicetree/bindings/mfd/da9062.txt and -Documentation/devicetree/bindings/mfd/da9063.txt +This module is part of the DA9061/DA9062/DA9063. For more details about entire +DA9062 and DA9061 chips see Documentation/devicetree/bindings/mfd/da9062.txt +For DA9063 see Documentation/devicetree/bindings/mfd/da9063.txt -This module provides KEY_POWER, KEY_SLEEP and events. +This module provides the KEY_POWER event. Required properties: -- compatible: should be one of: - dlg,da9062-onkey - dlg,da9063-onkey +- compatible: should be one of the following valid compatible string lines: + "dlg,da9061-onkey", "dlg,da9062-onkey" + "dlg,da9062-onkey" + "dlg,da9063-onkey" Optional properties: - - dlg,disable-key-power : Disable power-down using a long key-press. If this +- dlg,disable-key-power : Disable power-down using a long key-press. If this entry exists the OnKey driver will remove support for the KEY_POWER key - press. If this entry does not exist then by default the key-press - triggered power down is enabled and the OnKey will support both KEY_POWER - and KEY_SLEEP. + press when triggered using a long press of the OnKey. -Example: - - pmic0: da9062@58 { +Example: DA9063 + pmic0: da9063@58 { onkey { compatible = "dlg,da9063-onkey"; dlg,disable-key-power; }; + }; + +Example: DA9062 + + pmic0: da9062@58 { + onkey { + compatible = "dlg,da9062-onkey"; + dlg,disable-key-power; + }; + }; + +Example: DA9061 using a fall-back compatible for the DA9062 onkey driver + pmic0: da9061@58 { + onkey { + compatible = "dlg,da9061-onkey", "dlg,da9062-onkey"; + dlg,disable-key-power; + }; }; diff --git a/Documentation/devicetree/bindings/input/mpr121-touchkey.txt b/Documentation/devicetree/bindings/input/mpr121-touchkey.txt new file mode 100644 index 000000000000..b7c61ee5841b --- /dev/null +++ b/Documentation/devicetree/bindings/input/mpr121-touchkey.txt @@ -0,0 +1,30 @@ +* Freescale MPR121 Controllor + +Required Properties: +- compatible: Should be "fsl,mpr121-touchkey" +- reg: The I2C slave address of the device. +- interrupts: The interrupt number to the cpu. +- vdd-supply: Phandle to the Vdd power supply. +- linux,keycodes: Specifies an array of numeric keycode values to + be used for reporting button presses. The array can + contain up to 12 entries. + +Optional Properties: +- wakeup-source: Use any event on keypad as wakeup event. +- autorepeat: Enable autorepeat feature. + +Example: + +#include "dt-bindings/input/input.h" + + touchkey: mpr121@5a { + compatible = "fsl,mpr121-touchkey"; + reg = <0x5a>; + interrupt-parent = <&gpio1>; + interrupts = <28 2>; + autorepeat; + vdd-supply = <&ldo4_reg>; + linux,keycodes = <KEY_0>, <KEY_1>, <KEY_2>, <KEY_3>, + <KEY_4> <KEY_5>, <KEY_6>, <KEY_7>, + <KEY_8>, <KEY_9>, <KEY_A>, <KEY_B>; + }; diff --git a/Documentation/devicetree/bindings/input/pwm-beeper.txt b/Documentation/devicetree/bindings/input/pwm-beeper.txt index be332ae4f2d6..529408b4431a 100644 --- a/Documentation/devicetree/bindings/input/pwm-beeper.txt +++ b/Documentation/devicetree/bindings/input/pwm-beeper.txt @@ -5,3 +5,19 @@ Registers a PWM device as beeper. Required properties: - compatible: should be "pwm-beeper" - pwms: phandle to the physical PWM device + +Optional properties: +- amp-supply: phandle to a regulator that acts as an amplifier for the beeper + +Example: + +beeper_amp: amplifier { + compatible = "fixed-regulator"; + gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>; +}; + +beeper { + compatible = "pwm-beeper"; + pwms = <&pwm0>; + amp-supply = <&beeper_amp>; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt b/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt index 853dff96dd9f..d4927c202aef 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt @@ -17,6 +17,8 @@ Optional properties: This value depends on the touch screen. - pre-charge-time: the touch screen need some time to precharge. This value depends on the touch screen. +- touchscreen-average-samples: Number of data samples which are averaged for + each read. Valid values are 1, 4, 8, 16 and 32. Example: tsc: tsc@02040000 { @@ -32,5 +34,6 @@ Example: xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>; measure-delay-time = <0xfff>; pre-charge-time = <0xffff>; + touchscreen-average-samples = <32>; status = "okay"; }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt b/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt index 820fee4b77b6..ce85ee508238 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt @@ -18,6 +18,8 @@ Optional properties: - touchscreen-inverted-y : See touchscreen.txt - touchscreen-swapped-x-y : See touchscreen.txt - silead,max-fingers : maximum number of fingers the touchscreen can detect +- vddio-supply : regulator phandle for controller VDDIO +- avdd-supply : regulator phandle for controller AVDD Example: diff --git a/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt index bccaa4e73045..537643e86f61 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt @@ -14,6 +14,9 @@ Optional properties for Touchscreens: - touchscreen-fuzz-pressure : pressure noise value of the absolute input device (arbitrary range dependent on the controller) + - touchscreen-average-samples : Number of data samples which are averaged + for each read (valid values dependent on the + controller) - touchscreen-inverted-x : X axis is inverted (boolean) - touchscreen-inverted-y : Y axis is inverted (boolean) - touchscreen-swapped-x-y : X and Y axis are swapped (boolean) diff --git a/Documentation/devicetree/bindings/input/touchscreen/zet6223.txt b/Documentation/devicetree/bindings/input/touchscreen/zet6223.txt new file mode 100644 index 000000000000..fe6a1feef703 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/zet6223.txt @@ -0,0 +1,32 @@ +Zeitec ZET6223 I2C touchscreen controller + +Required properties: +- compatible : "zeitec,zet6223" +- reg : I2C slave address of the chip (0x76) +- interrupt-parent : a phandle pointing to the interrupt controller + serving the interrupt for this chip +- interrupts : interrupt specification for the zet6223 interrupt + +Optional properties: + +- vio-supply : Specification for VIO supply (1.8V or 3.3V, + depending on system interface needs). +- vcc-supply : Specification for 3.3V VCC supply. +- touchscreen-size-x : See touchscreen.txt +- touchscreen-size-y : See touchscreen.txt +- touchscreen-inverted-x : See touchscreen.txt +- touchscreen-inverted-y : See touchscreen.txt +- touchscreen-swapped-x-y : See touchscreen.txt + +Example: + +i2c@00000000 { + + zet6223: touchscreen@76 { + compatible = "zeitec,zet6223"; + reg = <0x76>; + interrupt-parent = <&pio>; + interrupts = <6 11 IRQ_TYPE_EDGE_FALLING> + }; + +}; diff --git a/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt b/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt index 3e5b9793341f..8682ab6d4a50 100644 --- a/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt +++ b/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt @@ -8,8 +8,9 @@ This driver provides a simple power button event via an Interrupt. Required properties: - compatible: should be "ti,tps65217-pwrbutton" or "ti,tps65218-pwrbutton" -Required properties for TPS65218: +Required properties: - interrupts: should be one of the following + - <2>: For controllers compatible with tps65217 - <3 IRQ_TYPE_EDGE_BOTH>: For controllers compatible with tps65218 Examples: @@ -17,6 +18,7 @@ Examples: &tps { tps65217-pwrbutton { compatible = "ti,tps65217-pwrbutton"; + interrupts = <2>; }; }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt index 5393e2a45a42..560d8a727b8f 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt @@ -111,7 +111,7 @@ Example: #interrupt-cells = <3>; interrupt-controller; reg = <0x2c001000 0x1000>, - <0x2c002000 0x1000>, + <0x2c002000 0x2000>, <0x2c004000 0x2000>, <0x2c006000 0x2000>; interrupts = <1 9 0xf04>; diff --git a/Documentation/devicetree/bindings/interrupt-controller/cortina,gemini-interrupt-controller.txt b/Documentation/devicetree/bindings/interrupt-controller/cortina,gemini-interrupt-controller.txt new file mode 100644 index 000000000000..97c1167fa533 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/cortina,gemini-interrupt-controller.txt @@ -0,0 +1,22 @@ +* Cortina Systems Gemini interrupt controller + +This interrupt controller is found on the Gemini SoCs. + +Required properties: +- compatible: must be "cortina,gemini-interrupt-controller" +- reg: The register bank for the interrupt controller. +- interrupt-controller: Identifies the node as an interrupt controller +- #interrupt-cells: The number of cells to define the interrupts. + Must be 2 as the controller can specify level or rising edge + IRQs. The bindings follows the standard binding for controllers + with two cells specified in + interrupt-controller/interrupts.txt + +Example: + +interrupt-controller@48000000 { + compatible = "cortina,gemini-interrupt-controller"; + reg = <0x48000000 0x1000>; + interrupt-controller; + #interrupt-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/snps,archs-idu-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/snps,archs-idu-intc.txt index 0dcb7c7d3e40..8b46a34e05f1 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/snps,archs-idu-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/snps,archs-idu-intc.txt @@ -8,12 +8,11 @@ Properties: - compatible: "snps,archs-idu-intc" - interrupt-controller: This is an interrupt controller. - interrupt-parent: <reference to parent core intc> -- #interrupt-cells: Must be <2>. -- interrupts: <...> specifies the upstream core irqs +- #interrupt-cells: Must be <1>. - First cell specifies the "common" IRQ from peripheral to IDU - Second cell specifies the irq distribution mode to cores - 0=Round Robin; 1=cpu0, 2=cpu1, 4=cpu2, 8=cpu3 + Value of the cell specifies the "common" IRQ from peripheral to IDU. Number N + of the particular interrupt line of IDU corresponds to the line N+24 of the + core interrupt controller. intc accessed via the special ARC AUX register interface, hence "reg" property is not specified. @@ -29,18 +28,10 @@ Example: compatible = "snps,archs-idu-intc"; interrupt-controller; interrupt-parent = <&core_intc>; - - /* - * <hwirq distribution> - * distribution: 0=RR; 1=cpu0, 2=cpu1, 4=cpu2, 8=cpu3 - */ - #interrupt-cells = <2>; - - /* upstream core irqs: downstream these are "COMMON" irq 0,1.. */ - interrupts = <24 25 26 27 28 29 30 31>; + #interrupt-cells = <1>; }; some_device: serial@c0fc1000 { interrupt-parent = <&idu_intc>; - interrupts = <0 0>; /* upstream idu IRQ #24, Round Robin */ + interrupts = <0>; /* upstream idu IRQ #24 */ }; diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu.txt b/Documentation/devicetree/bindings/iommu/arm,smmu.txt index e862d1485205..6cdf32d037fc 100644 --- a/Documentation/devicetree/bindings/iommu/arm,smmu.txt +++ b/Documentation/devicetree/bindings/iommu/arm,smmu.txt @@ -36,15 +36,15 @@ conditions. combined interrupt, it must be listed multiple times. - #iommu-cells : See Documentation/devicetree/bindings/iommu/iommu.txt - for details. With a value of 1, each "iommus" entry + for details. With a value of 1, each IOMMU specifier represents a distinct stream ID emitted by that device into the relevant SMMU. SMMUs with stream matching support and complex masters - may use a value of 2, where the second cell represents - an SMR mask to combine with the ID in the first cell. - Care must be taken to ensure the set of matched IDs - does not result in conflicts. + may use a value of 2, where the second cell of the + IOMMU specifier represents an SMR mask to combine with + the ID in the first cell. Care must be taken to ensure + the set of matched IDs does not result in conflicts. ** System MMU optional properties: diff --git a/Documentation/devicetree/bindings/leds/common.txt b/Documentation/devicetree/bindings/leds/common.txt index 696be5792625..24b656014089 100644 --- a/Documentation/devicetree/bindings/leds/common.txt +++ b/Documentation/devicetree/bindings/leds/common.txt @@ -61,16 +61,24 @@ property can be omitted. Examples: -system-status { - label = "Status"; - linux,default-trigger = "heartbeat"; - ... +gpio-leds { + compatible = "gpio-leds"; + + system-status { + label = "Status"; + linux,default-trigger = "heartbeat"; + gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; + }; }; -camera-flash { - label = "Flash"; - led-sources = <0>, <1>; - led-max-microamp = <50000>; - flash-max-microamp = <320000>; - flash-max-timeout-us = <500000>; +max77693-led { + compatible = "maxim,max77693-led"; + + camera-flash { + label = "Flash"; + led-sources = <0>, <1>; + led-max-microamp = <50000>; + flash-max-microamp = <320000>; + flash-max-timeout-us = <500000>; + }; }; diff --git a/Documentation/devicetree/bindings/leds/irled/spi-ir-led.txt b/Documentation/devicetree/bindings/leds/irled/spi-ir-led.txt new file mode 100644 index 000000000000..896b6997cf30 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/irled/spi-ir-led.txt @@ -0,0 +1,29 @@ +Device tree bindings for IR LED connected through SPI bus which is used as +remote controller. + +The IR LED switch is connected to the MOSI line of the SPI device and the data +are delivered thourgh that. + +Required properties: + - compatible: should be "ir-spi-led". + +Optional properties: + - duty-cycle: 8 bit balue that represents the percentage of one period + in which the signal is active. It can be 50, 60, 70, 75, 80 or 90. + - led-active-low: boolean value that specifies whether the output is + negated with a NOT gate. + - power-supply: specifies the power source. It can either be a regulator + or a gpio which enables a regulator, i.e. a regulator-fixed as + described in + Documentation/devicetree/bindings/regulator/fixed-regulator.txt + +Example: + + irled@0 { + compatible = "ir-spi-led"; + reg = <0x0>; + spi-max-frequency = <5000000>; + power-supply = <&vdd_led>; + led-active-low; + duty-cycle = /bits/ 8 <60>; + }; diff --git a/Documentation/devicetree/bindings/leds/pca963x.txt b/Documentation/devicetree/bindings/leds/pca963x.txt index dafbe9931c2b..dfbdb123a9bf 100644 --- a/Documentation/devicetree/bindings/leds/pca963x.txt +++ b/Documentation/devicetree/bindings/leds/pca963x.txt @@ -7,6 +7,9 @@ Optional properties: - nxp,totem-pole : use totem pole (push-pull) instead of open-drain (pca9632 defaults to open-drain, newer chips to totem pole) - nxp,hw-blink : use hardware blinking instead of software blinking +- nxp,period-scale : In some configurations, the chip blinks faster than expected. + This parameter provides a scaling ratio (fixed point, decimal divided + by 1000) to compensate, e.g. 1300=1.3x and 750=0.75x. Each led is represented as a sub-node of the nxp,pca963x device. diff --git a/Documentation/devicetree/bindings/mailbox/brcm,bcm2835-mbox.txt b/Documentation/devicetree/bindings/mailbox/brcm,bcm2835-mbox.txt index e893615ef635..b48d7d30012c 100644 --- a/Documentation/devicetree/bindings/mailbox/brcm,bcm2835-mbox.txt +++ b/Documentation/devicetree/bindings/mailbox/brcm,bcm2835-mbox.txt @@ -12,7 +12,7 @@ Required properties: Example: -mailbox: mailbox@7e00b800 { +mailbox: mailbox@7e00b880 { compatible = "brcm,bcm2835-mbox"; reg = <0x7e00b880 0x40>; interrupts = <0 1>; diff --git a/Documentation/devicetree/bindings/mailbox/nvidia,tegra186-hsp.txt b/Documentation/devicetree/bindings/mailbox/nvidia,tegra186-hsp.txt new file mode 100644 index 000000000000..b99d25fc2f26 --- /dev/null +++ b/Documentation/devicetree/bindings/mailbox/nvidia,tegra186-hsp.txt @@ -0,0 +1,52 @@ +NVIDIA Tegra Hardware Synchronization Primitives (HSP) + +The HSP modules are used for the processors to share resources and communicate +together. It provides a set of hardware synchronization primitives for +interprocessor communication. So the interprocessor communication (IPC) +protocols can use hardware synchronization primitives, when operating between +two processors not in an SMP relationship. + +The features that HSP supported are shared mailboxes, shared semaphores, +arbitrated semaphores and doorbells. + +Required properties: +- name : Should be hsp +- compatible + Array of strings. + one of: + - "nvidia,tegra186-hsp" +- reg : Offset and length of the register set for the device. +- interrupt-names + Array of strings. + Contains a list of names for the interrupts described by the interrupt + property. May contain the following entries, in any order: + - "doorbell" + Users of this binding MUST look up entries in the interrupt property + by name, using this interrupt-names property to do so. +- interrupts + Array of interrupt specifiers. + Must contain one entry per entry in the interrupt-names property, + in a matching order. +- #mbox-cells : Should be 2. + +The mbox specifier of the "mboxes" property in the client node should +contain two data. The first one should be the HSP type and the second +one should be the ID that the client is going to use. Those information +can be found in the following file. + +- <dt-bindings/mailbox/tegra186-hsp.h>. + +Example: + +hsp_top0: hsp@3c00000 { + compatible = "nvidia,tegra186-hsp"; + reg = <0x0 0x03c00000 0x0 0xa0000>; + interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "doorbell"; + #mbox-cells = <2>; +}; + +client { + ... + mboxes = <&hsp_top0 TEGRA_HSP_MBOX_TYPE_DB TEGRA_HSP_DB_MASTER_XXX>; +}; diff --git a/Documentation/devicetree/bindings/media/exynos5-gsc.txt b/Documentation/devicetree/bindings/media/exynos5-gsc.txt index 5fe9372abb37..26ca25b6d264 100644 --- a/Documentation/devicetree/bindings/media/exynos5-gsc.txt +++ b/Documentation/devicetree/bindings/media/exynos5-gsc.txt @@ -3,7 +3,8 @@ G-Scaler is used for scaling and color space conversion on EXYNOS5 SoCs. Required properties: -- compatible: should be "samsung,exynos5-gsc" +- compatible: should be "samsung,exynos5-gsc" (for Exynos 5250, 5420 and + 5422 SoCs) or "samsung,exynos5433-gsc" (Exynos 5433) - reg: should contain G-Scaler physical address location and length. - interrupts: should contain G-Scaler interrupt number diff --git a/Documentation/devicetree/bindings/media/fsl-vdoa.txt b/Documentation/devicetree/bindings/media/fsl-vdoa.txt new file mode 100644 index 000000000000..6c5628530bb7 --- /dev/null +++ b/Documentation/devicetree/bindings/media/fsl-vdoa.txt @@ -0,0 +1,21 @@ +Freescale Video Data Order Adapter +================================== + +The Video Data Order Adapter (VDOA) is present on the i.MX6q. Its sole purpose +is to reorder video data from the macroblock tiled order produced by the CODA +960 VPU to the conventional raster-scan order for scanout. + +Required properties: +- compatible: must be "fsl,imx6q-vdoa" +- reg: the register base and size for the device registers +- interrupts: the VDOA interrupt +- clocks: the vdoa clock + +Example: + +vdoa@21e4000 { + compatible = "fsl,imx6q-vdoa"; + reg = <0x021e4000 0x4000>; + interrupts = <0 18 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6QDL_CLK_VDOA>; +}; diff --git a/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt b/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt index 56e726ef4bf2..58261fb7b408 100644 --- a/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt +++ b/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt @@ -5,7 +5,8 @@ Required properties: - gpios: specifies GPIO used for IR signal reception. Optional properties: - - linux,rc-map-name: Linux specific remote control map name. + - linux,rc-map-name: see rc.txt file in the same + directory. Example node: diff --git a/Documentation/devicetree/bindings/media/hix5hd2-ir.txt b/Documentation/devicetree/bindings/media/hix5hd2-ir.txt index fb5e7606643a..13ebc0fac9ea 100644 --- a/Documentation/devicetree/bindings/media/hix5hd2-ir.txt +++ b/Documentation/devicetree/bindings/media/hix5hd2-ir.txt @@ -8,10 +8,11 @@ Required properties: the device. The interrupt specifier format depends on the interrupt controller parent. - clocks: clock phandle and specifier pair. - - hisilicon,power-syscon: phandle of syscon used to control power. Optional properties: - - linux,rc-map-name : Remote control map name. + - linux,rc-map-name: see rc.txt file in the same directory. + - hisilicon,power-syscon: DEPRECATED. Don't use this in new dts files. + Provide correct clocks instead. Example node: @@ -19,7 +20,6 @@ Example node: compatible = "hisilicon,hix5hd2-ir"; reg = <0xf8001000 0x1000>; interrupts = <0 47 4>; - clocks = <&clock HIX5HD2_FIXED_24M>; - hisilicon,power-syscon = <&sysctrl>; + clocks = <&clock HIX5HD2_IR_CLOCK>; linux,rc-map-name = "rc-tivo"; }; diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/Documentation/devicetree/bindings/media/i2c/adv7604.txt index 8337f75c75da..9cbd92eb5d05 100644 --- a/Documentation/devicetree/bindings/media/i2c/adv7604.txt +++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt @@ -34,6 +34,7 @@ The digital output port node must contain at least one endpoint. Optional Properties: - reset-gpios: Reference to the GPIO connected to the device's reset pin. + - default-input: Select which input is selected after reset. Optional Endpoint Properties: @@ -47,8 +48,6 @@ Optional Endpoint Properties: If none of hsync-active, vsync-active and pclk-sample is specified the endpoint will use embedded BT.656 synchronization. - - default-input: Select which input is selected after reset. - Example: hdmi_receiver@4c { diff --git a/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt new file mode 100644 index 000000000000..0b7b6a4d84ff --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt @@ -0,0 +1,48 @@ +Toshiba et8ek8 5MP sensor + +Toshiba et8ek8 5MP sensor is an image sensor found in Nokia N900 device + +More detailed documentation can be found in +Documentation/devicetree/bindings/media/video-interfaces.txt . + + +Mandatory properties +-------------------- + +- compatible: "toshiba,et8ek8" +- reg: I2C address (0x3e, or an alternative address) +- vana-supply: Analogue voltage supply (VANA), 2.8 volts +- clocks: External clock to the sensor +- clock-frequency: Frequency of the external clock to the sensor. Camera + driver will set this frequency on the external clock. The clock frequency is + a pre-determined frequency known to be suitable to the board. +- reset-gpios: XSHUTDOWN GPIO. The XSHUTDOWN signal is active low. The sensor + is in hardware standby mode when the signal is in the low state. + + +Endpoint node mandatory properties +---------------------------------- + +- remote-endpoint: A phandle to the bus receiver's endpoint node. + + +Example +------- + +&i2c3 { + clock-frequency = <400000>; + + cam1: camera@3e { + compatible = "toshiba,et8ek8"; + reg = <0x3e>; + vana-supply = <&vaux4>; + clocks = <&isp 0>; + clock-frequency = <9600000>; + reset-gpio = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102 */ + port { + csi_cam1: endpoint { + remote-endpoint = <&csi_out1>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/mediatek-mdp.txt b/Documentation/devicetree/bindings/media/mediatek-mdp.txt new file mode 100644 index 000000000000..4182063a54db --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek-mdp.txt @@ -0,0 +1,109 @@ +* Mediatek Media Data Path + +Media Data Path is used for scaling and color space conversion. + +Required properties (controller (parent) node): +- compatible: "mediatek,mt8173-mdp" +- mediatek,vpu: the node of video processor unit, see + Documentation/devicetree/bindings/media/mediatek-vpu.txt for details. + +Required properties (all function blocks, child node): +- compatible: Should be one of + "mediatek,mt8173-mdp-rdma" - read DMA + "mediatek,mt8173-mdp-rsz" - resizer + "mediatek,mt8173-mdp-wdma" - write DMA + "mediatek,mt8173-mdp-wrot" - write DMA with rotation +- reg: Physical base address and length of the function block register space +- clocks: device clocks, see + Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- power-domains: a phandle to the power domain, see + Documentation/devicetree/bindings/power/power_domain.txt for details. + +Required properties (DMA function blocks, child node): +- compatible: Should be one of + "mediatek,mt8173-mdp-rdma" + "mediatek,mt8173-mdp-wdma" + "mediatek,mt8173-mdp-wrot" +- iommus: should point to the respective IOMMU block with master port as + argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.txt + for details. +- mediatek,larb: must contain the local arbiters in the current Socs, see + Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt + for details. + +Example: +mdp { + compatible = "mediatek,mt8173-mdp"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + mediatek,vpu = <&vpu>; + + mdp_rdma0: rdma@14001000 { + compatible = "mediatek,mt8173-mdp-rdma"; + reg = <0 0x14001000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_RDMA0>, + <&mmsys CLK_MM_MUTEX_32K>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + iommus = <&iommu M4U_PORT_MDP_RDMA0>; + mediatek,larb = <&larb0>; + }; + + mdp_rdma1: rdma@14002000 { + compatible = "mediatek,mt8173-mdp-rdma"; + reg = <0 0x14002000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_RDMA1>, + <&mmsys CLK_MM_MUTEX_32K>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + iommus = <&iommu M4U_PORT_MDP_RDMA1>; + mediatek,larb = <&larb4>; + }; + + mdp_rsz0: rsz@14003000 { + compatible = "mediatek,mt8173-mdp-rsz"; + reg = <0 0x14003000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_RSZ0>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + }; + + mdp_rsz1: rsz@14004000 { + compatible = "mediatek,mt8173-mdp-rsz"; + reg = <0 0x14004000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_RSZ1>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + }; + + mdp_rsz2: rsz@14005000 { + compatible = "mediatek,mt8173-mdp-rsz"; + reg = <0 0x14005000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_RSZ2>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + }; + + mdp_wdma0: wdma@14006000 { + compatible = "mediatek,mt8173-mdp-wdma"; + reg = <0 0x14006000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_WDMA>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + iommus = <&iommu M4U_PORT_MDP_WDMA>; + mediatek,larb = <&larb0>; + }; + + mdp_wrot0: wrot@14007000 { + compatible = "mediatek,mt8173-mdp-wrot"; + reg = <0 0x14007000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_WROT0>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + iommus = <&iommu M4U_PORT_MDP_WROT0>; + mediatek,larb = <&larb0>; + }; + + mdp_wrot1: wrot@14008000 { + compatible = "mediatek,mt8173-mdp-wrot"; + reg = <0 0x14008000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_WROT1>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + iommus = <&iommu M4U_PORT_MDP_WROT1>; + mediatek,larb = <&larb4>; + }; +}; diff --git a/Documentation/devicetree/bindings/media/mediatek-vcodec.txt b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt index 59a47a5b924b..46c15c54175d 100644 --- a/Documentation/devicetree/bindings/media/mediatek-vcodec.txt +++ b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt @@ -1,25 +1,74 @@ Mediatek Video Codec Mediatek Video Codec is the video codec hw present in Mediatek SoCs which -supports high resolution encoding functionalities. +supports high resolution encoding and decoding functionalities. Required properties: - compatible : "mediatek,mt8173-vcodec-enc" for encoder + "mediatek,mt8173-vcodec-dec" for decoder. - reg : Physical base address of the video codec registers and length of memory mapped region. - interrupts : interrupt number to the cpu. - mediatek,larb : must contain the local arbiters in the current Socs. - clocks : list of clock specifiers, corresponding to entries in the clock-names property. -- clock-names: encoder must contain "venc_sel_src", "venc_sel", -- "venc_lt_sel_src", "venc_lt_sel". +- clock-names: encoder must contain "venc_sel_src", "venc_sel",, + "venc_lt_sel_src", "venc_lt_sel", decoder must contain "vcodecpll", + "univpll_d2", "clk_cci400_sel", "vdec_sel", "vdecpll", "vencpll", + "venc_lt_sel", "vdec_bus_clk_src". - iommus : should point to the respective IOMMU block with master port as argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.txt for details. - mediatek,vpu : the node of video processor unit + Example: -vcodec_enc: vcodec@0x18002000 { + +vcodec_dec: vcodec@16000000 { + compatible = "mediatek,mt8173-vcodec-dec"; + reg = <0 0x16000000 0 0x100>, /*VDEC_SYS*/ + <0 0x16020000 0 0x1000>, /*VDEC_MISC*/ + <0 0x16021000 0 0x800>, /*VDEC_LD*/ + <0 0x16021800 0 0x800>, /*VDEC_TOP*/ + <0 0x16022000 0 0x1000>, /*VDEC_CM*/ + <0 0x16023000 0 0x1000>, /*VDEC_AD*/ + <0 0x16024000 0 0x1000>, /*VDEC_AV*/ + <0 0x16025000 0 0x1000>, /*VDEC_PP*/ + <0 0x16026800 0 0x800>, /*VP8_VD*/ + <0 0x16027000 0 0x800>, /*VP6_VD*/ + <0 0x16027800 0 0x800>, /*VP8_VL*/ + <0 0x16028400 0 0x400>; /*VP9_VD*/ + interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_LOW>; + mediatek,larb = <&larb1>; + iommus = <&iommu M4U_PORT_HW_VDEC_MC_EXT>, + <&iommu M4U_PORT_HW_VDEC_PP_EXT>, + <&iommu M4U_PORT_HW_VDEC_AVC_MV_EXT>, + <&iommu M4U_PORT_HW_VDEC_PRED_RD_EXT>, + <&iommu M4U_PORT_HW_VDEC_PRED_WR_EXT>, + <&iommu M4U_PORT_HW_VDEC_UFO_EXT>, + <&iommu M4U_PORT_HW_VDEC_VLD_EXT>, + <&iommu M4U_PORT_HW_VDEC_VLD2_EXT>; + mediatek,vpu = <&vpu>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_VDEC>; + clocks = <&apmixedsys CLK_APMIXED_VCODECPLL>, + <&topckgen CLK_TOP_UNIVPLL_D2>, + <&topckgen CLK_TOP_CCI400_SEL>, + <&topckgen CLK_TOP_VDEC_SEL>, + <&topckgen CLK_TOP_VCODECPLL>, + <&apmixedsys CLK_APMIXED_VENCPLL>, + <&topckgen CLK_TOP_VENC_LT_SEL>, + <&topckgen CLK_TOP_VCODECPLL_370P5>; + clock-names = "vcodecpll", + "univpll_d2", + "clk_cci400_sel", + "vdec_sel", + "vdecpll", + "vencpll", + "venc_lt_sel", + "vdec_bus_clk_src"; + }; + + vcodec_enc: vcodec@0x18002000 { compatible = "mediatek,mt8173-vcodec-enc"; reg = <0 0x18002000 0 0x1000>, /*VENC_SYS*/ <0 0x19002000 0 0x1000>; /*VENC_LT_SYS*/ diff --git a/Documentation/devicetree/bindings/media/meson-ir.txt b/Documentation/devicetree/bindings/media/meson-ir.txt index e7e3f3c4fc8f..efd9d29a8f10 100644 --- a/Documentation/devicetree/bindings/media/meson-ir.txt +++ b/Documentation/devicetree/bindings/media/meson-ir.txt @@ -8,6 +8,9 @@ Required properties: - reg : physical base address and length of the device registers - interrupts : a single specifier for the interrupt from the device +Optional properties: + - linux,rc-map-name: see rc.txt file in the same directory. + Example: ir-receiver@c8100480 { diff --git a/Documentation/devicetree/bindings/media/mtk-cir.txt b/Documentation/devicetree/bindings/media/mtk-cir.txt new file mode 100644 index 000000000000..2be2005577d6 --- /dev/null +++ b/Documentation/devicetree/bindings/media/mtk-cir.txt @@ -0,0 +1,24 @@ +Device-Tree bindings for Mediatek consumer IR controller +found in Mediatek SoC family + +Required properties: +- compatible : "mediatek,mt7623-cir" +- clocks : list of clock specifiers, corresponding to + entries in clock-names property; +- clock-names : should contain "clk" entries; +- interrupts : should contain IR IRQ number; +- reg : should contain IO map address for IR. + +Optional properties: +- linux,rc-map-name : see rc.txt file in the same directory. + +Example: + +cir: cir@10013000 { + compatible = "mediatek,mt7623-cir"; + reg = <0 0x10013000 0 0x1000>; + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_INFRA_IRRX>; + clock-names = "clk"; + linux,rc-map-name = "rc-rc6-mce"; +}; diff --git a/Documentation/devicetree/bindings/media/rc.txt b/Documentation/devicetree/bindings/media/rc.txt new file mode 100644 index 000000000000..d3e7a012bfda --- /dev/null +++ b/Documentation/devicetree/bindings/media/rc.txt @@ -0,0 +1,117 @@ +The following properties are common to the infrared remote controllers: + +- linux,rc-map-name: string, specifies the scancode/key mapping table + defined in-kernel for the remote controller. Support values are: + * "rc-adstech-dvb-t-pci" + * "rc-alink-dtu-m" + * "rc-anysee" + * "rc-apac-viewcomp" + * "rc-asus-pc39" + * "rc-asus-ps3-100" + * "rc-ati-tv-wonder-hd-600" + * "rc-ati-x10" + * "rc-avermedia-a16d" + * "rc-avermedia-cardbus" + * "rc-avermedia-dvbt" + * "rc-avermedia-m135a" + * "rc-avermedia-m733a-rm-k6" + * "rc-avermedia-rm-ks" + * "rc-avermedia" + * "rc-avertv-303" + * "rc-azurewave-ad-tu700" + * "rc-behold-columbus" + * "rc-behold" + * "rc-budget-ci-old" + * "rc-cec" + * "rc-cinergy-1400" + * "rc-cinergy" + * "rc-delock-61959" + * "rc-dib0700-nec" + * "rc-dib0700-rc5" + * "rc-digitalnow-tinytwin" + * "rc-digittrade" + * "rc-dm1105-nec" + * "rc-dntv-live-dvbt-pro" + * "rc-dntv-live-dvb-t" + * "rc-dtt200u" + * "rc-dvbsky" + * "rc-empty" + * "rc-em-terratec" + * "rc-encore-enltv2" + * "rc-encore-enltv-fm53" + * "rc-encore-enltv" + * "rc-evga-indtube" + * "rc-eztv" + * "rc-flydvb" + * "rc-flyvideo" + * "rc-fusionhdtv-mce" + * "rc-gadmei-rm008z" + * "rc-geekbox" + * "rc-genius-tvgo-a11mce" + * "rc-gotview7135" + * "rc-hauppauge" + * "rc-imon-mce" + * "rc-imon-pad" + * "rc-iodata-bctv7e" + * "rc-it913x-v1" + * "rc-it913x-v2" + * "rc-kaiomy" + * "rc-kworld-315u" + * "rc-kworld-pc150u" + * "rc-kworld-plus-tv-analog" + * "rc-leadtek-y04g0051" + * "rc-lirc" + * "rc-lme2510" + * "rc-manli" + * "rc-medion-x10" + * "rc-medion-x10-digitainer" + * "rc-medion-x10-or2x" + * "rc-msi-digivox-ii" + * "rc-msi-digivox-iii" + * "rc-msi-tvanywhere-plus" + * "rc-msi-tvanywhere" + * "rc-nebula" + * "rc-nec-terratec-cinergy-xs" + * "rc-norwood" + * "rc-npgtech" + * "rc-pctv-sedna" + * "rc-pinnacle-color" + * "rc-pinnacle-grey" + * "rc-pinnacle-pctv-hd" + * "rc-pixelview-new" + * "rc-pixelview" + * "rc-pixelview-002t" + * "rc-pixelview-mk12" + * "rc-powercolor-real-angel" + * "rc-proteus-2309" + * "rc-purpletv" + * "rc-pv951" + * "rc-hauppauge" + * "rc-rc5-tv" + * "rc-rc6-mce" + * "rc-real-audio-220-32-keys" + * "rc-reddo" + * "rc-snapstream-firefly" + * "rc-streamzap" + * "rc-tbs-nec" + * "rc-technisat-ts35" + * "rc-technisat-usb2" + * "rc-terratec-cinergy-c-pci" + * "rc-terratec-cinergy-s2-hd" + * "rc-terratec-cinergy-xs" + * "rc-terratec-slim" + * "rc-terratec-slim-2" + * "rc-tevii-nec" + * "rc-tivo" + * "rc-total-media-in-hand" + * "rc-total-media-in-hand-02" + * "rc-trekstor" + * "rc-tt-1500" + * "rc-twinhan-dtv-cab-ci" + * "rc-twinhan1027" + * "rc-videomate-k100" + * "rc-videomate-s350" + * "rc-videomate-tv-pvr" + * "rc-winfast" + * "rc-winfast-usbii-deluxe" + * "rc-su3000" diff --git a/Documentation/devicetree/bindings/media/renesas,fcp.txt b/Documentation/devicetree/bindings/media/renesas,fcp.txt index 27f9b8e459ac..3ec91803ba58 100644 --- a/Documentation/devicetree/bindings/media/renesas,fcp.txt +++ b/Documentation/devicetree/bindings/media/renesas,fcp.txt @@ -11,15 +11,9 @@ are paired with. These DT bindings currently support the FCPV and FCPF. - compatible: Must be one or more of the following - - "renesas,r8a7795-fcpv" for R8A7795 (R-Car H3) compatible 'FCP for VSP' - - "renesas,r8a7795-fcpf" for R8A7795 (R-Car H3) compatible 'FCP for FDP' - "renesas,fcpv" for generic compatible 'FCP for VSP' - "renesas,fcpf" for generic compatible 'FCP for FDP' - When compatible with the generic version, nodes must list the - SoC-specific version corresponding to the platform first, followed by the - family-specific and/or generic versions. - - reg: the register base and size for the device registers - clocks: Reference to the functional clock @@ -32,7 +26,7 @@ Device node example ------------------- fcpvd1: fcp@fea2f000 { - compatible = "renesas,r8a7795-fcpv", "renesas,fcpv"; + compatible = "renesas,fcpv"; reg = <0 0xfea2f000 0 0x200>; clocks = <&cpg CPG_MOD 602>; power-domains = <&sysc R8A7795_PD_A3VP>; diff --git a/Documentation/devicetree/bindings/media/renesas,fdp1.txt b/Documentation/devicetree/bindings/media/renesas,fdp1.txt new file mode 100644 index 000000000000..8dd1007bb573 --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,fdp1.txt @@ -0,0 +1,37 @@ +Renesas R-Car Fine Display Processor (FDP1) +------------------------------------------- + +The FDP1 is a de-interlacing module which converts interlaced video to +progressive video. It is capable of performing pixel format conversion between +YCbCr/YUV formats and RGB formats. Only YCbCr/YUV formats are supported as +an input to the module. + +Required properties: + + - compatible: must be "renesas,fdp1" + - reg: the register base and size for the device registers + - interrupts : interrupt specifier for the FDP1 instance + - clocks: reference to the functional clock + +Optional properties: + + - power-domains: reference to the power domain that the FDP1 belongs to, if + any. + - renesas,fcp: a phandle referencing the FCP that handles memory accesses + for the FDP1. Not needed on Gen2, mandatory on Gen3. + +Please refer to the binding documentation for the clock and/or power domain +providers for more details. + + +Device node example +------------------- + + fdp1@fe940000 { + compatible = "renesas,fdp1"; + reg = <0 0xfe940000 0 0x2400>; + interrupts = <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 119>; + power-domains = <&sysc R8A7795_PD_A3VP>; + renesas,fcp = <&fcpf0>; + }; diff --git a/Documentation/devicetree/bindings/media/s5p-mfc.txt b/Documentation/devicetree/bindings/media/s5p-mfc.txt index 92c94f5ecbf1..2c901286d818 100644 --- a/Documentation/devicetree/bindings/media/s5p-mfc.txt +++ b/Documentation/devicetree/bindings/media/s5p-mfc.txt @@ -12,6 +12,7 @@ Required properties: (b) "samsung,mfc-v6" for MFC v6 present in Exynos5 SoCs (c) "samsung,mfc-v7" for MFC v7 present in Exynos5420 SoC (d) "samsung,mfc-v8" for MFC v8 present in Exynos5800 SoC + (e) "samsung,exynos5433-mfc" for MFC v8 present in Exynos5433 SoC - reg : Physical base address of the IP registers and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/media/st,st-delta.txt b/Documentation/devicetree/bindings/media/st,st-delta.txt new file mode 100644 index 000000000000..a538ab30a617 --- /dev/null +++ b/Documentation/devicetree/bindings/media/st,st-delta.txt @@ -0,0 +1,17 @@ +* STMicroelectronics DELTA multi-format video decoder + +Required properties: +- compatible: should be "st,st-delta". +- clocks: from common clock binding: handle hardware IP needed clocks, the + number of clocks may depend on the SoC type. + See ../clock/clock-bindings.txt for details. +- clock-names: names of the clocks listed in clocks property in the same order. + +Example: + delta0 { + compatible = "st,st-delta"; + clock-names = "delta", "delta-st231", "delta-flash-promip"; + clocks = <&clk_s_c0_flexgen CLK_VID_DMU>, + <&clk_s_c0_flexgen CLK_ST231_DMU>, + <&clk_s_c0_flexgen CLK_FLASH_PROMIP>; + }; diff --git a/Documentation/devicetree/bindings/media/sunxi-ir.txt b/Documentation/devicetree/bindings/media/sunxi-ir.txt index 1811a067c72c..302a0b183cb8 100644 --- a/Documentation/devicetree/bindings/media/sunxi-ir.txt +++ b/Documentation/devicetree/bindings/media/sunxi-ir.txt @@ -9,7 +9,7 @@ Required properties: - reg : should contain IO map address for IR. Optional properties: -- linux,rc-map-name : Remote control map name. +- linux,rc-map-name: see rc.txt file in the same directory. - resets : phandle + reset specifier pair Example: diff --git a/Documentation/devicetree/bindings/media/ti,da850-vpif.txt b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt new file mode 100644 index 000000000000..6d25d7f23d26 --- /dev/null +++ b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt @@ -0,0 +1,83 @@ +Texas Instruments VPIF +---------------------- + +The TI Video Port InterFace (VPIF) is the primary component for video +capture and display on the DA850/AM18x family of TI DaVinci/Sitara +SoCs. + +TI Document reference: SPRUH82C, Chapter 35 +http://www.ti.com/lit/pdf/spruh82 + +Required properties: +- compatible: must be "ti,da850-vpif" +- reg: physical base address and length of the registers set for the device; +- interrupts: should contain IRQ line for the VPIF + +Video Capture: + +VPIF has a 16-bit parallel bus input, supporting 2 8-bit channels or a +single 16-bit channel. It should contain at least one port child node +with child 'endpoint' node. Please refer to the bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example using 2 8-bit input channels, one of which is connected to an +I2C-connected TVP5147 decoder: + + vpif: vpif@217000 { + compatible = "ti,da850-vpif"; + reg = <0x217000 0x1000>; + interrupts = <92>; + + port { + vpif_ch0: endpoint@0 { + reg = <0>; + bus-width = <8>; + remote-endpoint = <&composite>; + }; + + vpif_ch1: endpoint@1 { + reg = <1>; + bus-width = <8>; + data-shift = <8>; + }; + }; + }; + +[ ... ] + +&i2c0 { + + tvp5147@5d { + compatible = "ti,tvp5147"; + reg = <0x5d>; + status = "okay"; + + port { + composite: endpoint { + hsync-active = <1>; + vsync-active = <1>; + pclk-sample = <0>; + + /* VPIF channel 0 (lower 8-bits) */ + remote-endpoint = <&vpif_ch0>; + bus-width = <8>; + }; + }; + }; +}; + + +Alternatively, an example when the bus is configured as a single +16-bit input (e.g. for raw-capture mode): + + vpif: vpif@217000 { + compatible = "ti,da850-vpif"; + reg = <0x217000 0x1000>; + interrupts = <92>; + + port { + vpif_ch0: endpoint { + bus-width = <16>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/ti-da8xx-ddrctl.txt b/Documentation/devicetree/bindings/memory-controllers/ti-da8xx-ddrctl.txt new file mode 100644 index 000000000000..ec1dd408d573 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/ti-da8xx-ddrctl.txt @@ -0,0 +1,20 @@ +* Device tree bindings for Texas Instruments da8xx DDR2/mDDR memory controller + +The DDR2/mDDR memory controller present on Texas Instruments da8xx SoCs features +a set of registers which allow to tweak the controller's behavior. + +Documentation: +OMAP-L138 (DA850) - http://www.ti.com/lit/ug/spruh82c/spruh82c.pdf + +Required properties: + +- compatible: "ti,da850-ddr-controller" - for da850 SoC based boards +- reg: a tuple containing the base address of the memory + controller and the size of the memory area to map + +Example for da850 shown below. + +ddrctl { + compatible = "ti,da850-ddr-controller"; + reg = <0xb0000000 0xe8>; +}; diff --git a/Documentation/devicetree/bindings/mfd/altera-a10sr.txt b/Documentation/devicetree/bindings/mfd/altera-a10sr.txt new file mode 100644 index 000000000000..ea151f295ad7 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/altera-a10sr.txt @@ -0,0 +1,46 @@ +* Altera Arria10 Development Kit System Resource Chip + +Required parent device properties: +- compatible : "altr,a10sr" +- spi-max-frequency : Maximum SPI frequency. +- reg : The SPI Chip Select address for the Arria10 + System Resource chip +- interrupt-parent : The parent interrupt controller. +- interrupts : The interrupt line the device is connected to. +- interrupt-controller : Marks the device node as an interrupt controller. +- #interrupt-cells : The number of cells to describe an IRQ, should be 2. + The first cell is the IRQ number. + The second cell is the flags, encoded as trigger + masks from ../interrupt-controller/interrupts.txt. + +The A10SR consists of these sub-devices: + +Device Description +------ ---------- +a10sr_gpio GPIO Controller + +Arria10 GPIO +Required Properties: +- compatible : Should be "altr,a10sr-gpio" +- gpio-controller : Marks the device node as a GPIO Controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../gpio/gpio.txt for more information. + +Example: + + resource-manager@0 { + compatible = "altr,a10sr"; + reg = <0>; + spi-max-frequency = <100000>; + interrupt-parent = <&portb>; + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + + a10sr_gpio: gpio-controller { + compatible = "altr,a10sr-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/as3722.txt b/Documentation/devicetree/bindings/mfd/as3722.txt index 4f64b2a73169..0b2a6099aa20 100644 --- a/Documentation/devicetree/bindings/mfd/as3722.txt +++ b/Documentation/devicetree/bindings/mfd/as3722.txt @@ -122,8 +122,7 @@ Following are properties of regulator subnode. Power-off: ========= -AS3722 supports the system power off by turning off all its rail. This -is provided through pm_power_off. +AS3722 supports the system power off by turning off all its rails. The device node should have the following properties to enable this functionality ams,system-power-controller: Boolean, to enable the power off functionality diff --git a/Documentation/devicetree/bindings/mfd/aspeed-gfx.txt b/Documentation/devicetree/bindings/mfd/aspeed-gfx.txt new file mode 100644 index 000000000000..aea5370efd97 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/aspeed-gfx.txt @@ -0,0 +1,17 @@ +* Device tree bindings for Aspeed SoC Display Controller (GFX) + +The Aspeed SoC Display Controller primarily does as its name suggests, but also +participates in pinmux requests on the g5 SoCs. It is therefore considered a +syscon device. + +Required properties: +- compatible: "aspeed,ast2500-gfx", "syscon" +- reg: contains offset/length value of the GFX memory + region. + +Example: + +gfx: display@1e6e6000 { + compatible = "aspeed,ast2500-gfx", "syscon"; + reg = <0x1e6e6000 0x1000>; +}; diff --git a/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt b/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt new file mode 100644 index 000000000000..514d82ced95b --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt @@ -0,0 +1,137 @@ +====================================================================== +Device tree bindings for the Aspeed Low Pin Count (LPC) Bus Controller +====================================================================== + +The LPC bus is a means to bridge a host CPU to a number of low-bandwidth +peripheral devices, replacing the use of the ISA bus in the age of PCI[0]. The +primary use case of the Aspeed LPC controller is as a slave on the bus +(typically in a Baseboard Management Controller SoC), but under certain +conditions it can also take the role of bus master. + +The LPC controller is represented as a multi-function device to account for the +mix of functionality it provides. The principle split is between the register +layout at the start of the I/O space which is, to quote the Aspeed datasheet, +"basically compatible with the [LPC registers from the] popular BMC controller +H8S/2168[1]", and everything else, where everything else is an eclectic +collection of functions with a esoteric register layout. "Everything else", +here labeled the "host" portion of the controller, includes, but is not limited +to: + +* An IPMI Block Transfer[2] Controller + +* An LPC Host Controller: Manages LPC functions such as host vs slave mode, the + physical properties of some LPC pins, configuration of serial IRQs, and + APB-to-LPC bridging amonst other functions. + +* An LPC Host Interface Controller: Manages functions exposed to the host such + as LPC firmware hub cycles, configuration of the LPC-to-AHB mapping, UART + management and bus snoop configuration. + +* A set of SuperIO[3] scratch registers: Enables implementation of e.g. custom + hardware management protocols for handover between the host and baseboard + management controller. + +Additionally the state of the LPC controller influences the pinmux +configuration, therefore the host portion of the controller is exposed as a +syscon as a means to arbitrate access. + +[0] http://www.intel.com/design/chipsets/industry/25128901.pdf +[1] https://www.renesas.com/en-sg/doc/products/mpumcu/001/rej09b0078_h8s2168.pdf?key=7c88837454702128622bee53acbda8f4 +[2] http://www.intel.com/content/dam/www/public/us/en/documents/product-briefs/ipmi-second-gen-interface-spec-v2-rev1-1.pdf +[3] https://en.wikipedia.org/wiki/Super_I/O + +Required properties +=================== + +- compatible: One of: + "aspeed,ast2400-lpc", "simple-mfd" + "aspeed,ast2500-lpc", "simple-mfd" + +- reg: contains the physical address and length values of the Aspeed + LPC memory region. + +- #address-cells: <1> +- #size-cells: <1> +- ranges: Maps 0 to the physical address and length of the LPC memory + region + +Required LPC Child nodes +======================== + +BMC Node +-------- + +- compatible: One of: + "aspeed,ast2400-lpc-bmc" + "aspeed,ast2500-lpc-bmc" + +- reg: contains the physical address and length values of the + H8S/2168-compatible LPC controller memory region + +Host Node +--------- + +- compatible: One of: + "aspeed,ast2400-lpc-host", "simple-mfd", "syscon" + "aspeed,ast2500-lpc-host", "simple-mfd", "syscon" + +- reg: contains the address and length values of the host-related + register space for the Aspeed LPC controller + +- #address-cells: <1> +- #size-cells: <1> +- ranges: Maps 0 to the address and length of the host-related LPC memory + region + +Example: + +lpc: lpc@1e789000 { + compatible = "aspeed,ast2500-lpc", "simple-mfd"; + reg = <0x1e789000 0x1000>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x1e789000 0x1000>; + + lpc_bmc: lpc-bmc@0 { + compatible = "aspeed,ast2500-lpc-bmc"; + reg = <0x0 0x80>; + }; + + lpc_host: lpc-host@80 { + compatible = "aspeed,ast2500-lpc-host", "simple-mfd", "syscon"; + reg = <0x80 0x1e0>; + reg-io-width = <4>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x80 0x1e0>; + }; +}; + +Host Node Children +================== + +LPC Host Controller +------------------- + +The Aspeed LPC Host Controller configures the Low Pin Count (LPC) bus behaviour +between the host and the baseboard management controller. The registers exist +in the "host" portion of the Aspeed LPC controller, which must be the parent of +the LPC host controller node. + +Required properties: + +- compatible: One of: + "aspeed,ast2400-lhc"; + "aspeed,ast2500-lhc"; + +- reg: contains offset/length values of the LHC memory regions. In the + AST2400 and AST2500 there are two regions. + +Example: + +lhc: lhc@20 { + compatible = "aspeed,ast2500-lhc"; + reg = <0x20 0x24 0x48 0x8>; +}; diff --git a/Documentation/devicetree/bindings/mfd/lp873x.txt b/Documentation/devicetree/bindings/mfd/lp873x.txt index 52766c2035f7..ae9cf39bd101 100644 --- a/Documentation/devicetree/bindings/mfd/lp873x.txt +++ b/Documentation/devicetree/bindings/mfd/lp873x.txt @@ -7,6 +7,9 @@ Required properties: - #gpio-cells: Should be two. The first cell is the pin number and the second cell is used to specify flags. See ../gpio/gpio.txt for more information. + - xxx-in-supply: Phandle to parent supply node of each regulator + populated under regulators node. xxx can be + buck0, buck1, ldo0 or ldo1. - regulators: List of child nodes that specify the regulator initialization data. Example: @@ -17,6 +20,11 @@ pmic: lp8733@60 { gpio-controller; #gpio-cells = <2>; + buck0-in-supply = <&vsys_3v3>; + buck1-in-supply = <&vsys_3v3>; + ldo0-in-supply = <&vsys_3v3>; + ldo1-in-supply = <&vsys_3v3>; + regulators { lp8733_buck0: buck0 { regulator-name = "lp8733-buck0"; diff --git a/Documentation/devicetree/bindings/mfd/max77620.txt b/Documentation/devicetree/bindings/mfd/max77620.txt index 2ad44f7e4880..9c16d51cc15b 100644 --- a/Documentation/devicetree/bindings/mfd/max77620.txt +++ b/Documentation/devicetree/bindings/mfd/max77620.txt @@ -106,6 +106,18 @@ Here supported time periods by device in microseconds are as follows: MAX77620 supports 40, 80, 160, 320, 640, 1280, 2560 and 5120 microseconds. MAX20024 supports 20, 40, 80, 160, 320, 640, 1280 and 2540 microseconds. +-maxim,power-ok-control: configure map power ok bit + 1: Enables POK(Power OK) to control nRST_IO and GPIO1 + POK function. + 0: Disables POK control. + if property missing, do not configure MPOK bit. + If POK mapping is enabled for GPIO1/nRST_IO then, + GPIO1/nRST_IO pins are HIGH only if all rails + that have POK control enabled are HIGH. + If any of the rails goes down(which are enabled for POK + control) then, GPIO1/nRST_IO goes LOW. + this property is valid for max20024 only. + For DT binding details of different sub modules like GPIO, pincontrol, regulator, power, please refer respective device-tree binding document under their respective sub-system directories. diff --git a/Documentation/devicetree/bindings/mfd/mfd.txt b/Documentation/devicetree/bindings/mfd/mfd.txt index af9d6931a1a2..bcb6abb9d413 100644 --- a/Documentation/devicetree/bindings/mfd/mfd.txt +++ b/Documentation/devicetree/bindings/mfd/mfd.txt @@ -19,12 +19,22 @@ Optional properties: - compatible : "simple-mfd" - this signifies that the operating system should consider all subnodes of the MFD device as separate devices akin to how - "simple-bus" inidicates when to see subnodes as children for a simple + "simple-bus" indicates when to see subnodes as children for a simple memory-mapped bus. For more complex devices, when the nexus driver has to probe registers to figure out what child devices exist etc, this should not be used. In the latter case the child devices will be determined by the operating system. +- ranges: Describes the address mapping relationship to the parent. Should set + the child's base address to 0, the physical address within parent's address + space, and the length of the address map. + +- #address-cells: Specifies the number of cells used to represent physical base + addresses. Must be present if ranges is used. + +- #size-cells: Specifies the number of cells used to represent the size of an + address. Must be present if ranges is used. + Example: foo@1000 { diff --git a/Documentation/devicetree/bindings/mfd/motorola-cpcap.txt b/Documentation/devicetree/bindings/mfd/motorola-cpcap.txt new file mode 100644 index 000000000000..15bc885f9df4 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/motorola-cpcap.txt @@ -0,0 +1,31 @@ +Motorola CPCAP PMIC device tree binding + +Required properties: +- compatible : One or both of "motorola,cpcap" or "ste,6556002" +- reg : SPI chip select +- interrupt-parent : The parent interrupt controller +- interrupts : The interrupt line the device is connected to +- interrupt-controller : Marks the device node as an interrupt controller +- #interrupt-cells : The number of cells to describe an IRQ, should be 2 +- #address-cells : Child device offset number of cells, should be 1 +- #size-cells : Child device size number of cells, should be 0 +- spi-max-frequency : Typically set to 3000000 +- spi-cs-high : SPI chip select direction + +Example: + +&mcspi1 { + cpcap: pmic@0 { + compatible = "motorola,cpcap", "ste,6556002"; + reg = <0>; /* cs0 */ + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_EDGE_RISING>; + interrupt-controller; + #interrupt-cells = <2>; + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <3000000>; + spi-cs-high; + }; +}; + diff --git a/Documentation/devicetree/bindings/mfd/mt6397.txt b/Documentation/devicetree/bindings/mfd/mt6397.txt index 949c85f8d02c..c568d52af5af 100644 --- a/Documentation/devicetree/bindings/mfd/mt6397.txt +++ b/Documentation/devicetree/bindings/mfd/mt6397.txt @@ -34,6 +34,10 @@ Optional subnodes: - clk Required properties: - compatible: "mediatek,mt6397-clk" +- led + Required properties: + - compatible: "mediatek,mt6323-led" + see Documentation/devicetree/bindings/leds/leds-mt6323.txt Example: pwrap: pwrap@1000f000 { diff --git a/Documentation/devicetree/bindings/mfd/omap-usb-host.txt b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt index 4721b2d521e4..aa1eaa59581b 100644 --- a/Documentation/devicetree/bindings/mfd/omap-usb-host.txt +++ b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt @@ -64,8 +64,8 @@ Required properties if child node exists: Properties for children: The OMAP HS USB Host subsystem contains EHCI and OHCI controllers. -See Documentation/devicetree/bindings/usb/omap-ehci.txt and -omap3-ohci.txt +See Documentation/devicetree/bindings/usb/ehci-omap.txt and +Documentation/devicetree/bindings/usb/ohci-omap3.txt. Example for OMAP4: diff --git a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt index 37a088f9a648..9e5eba4a4f0d 100644 --- a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt +++ b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt @@ -10,6 +10,7 @@ voltages and other various functionality to Qualcomm SoCs. Value type: <string> Definition: must be one of: "qcom,pm8058" + "qcom,pm8821" "qcom,pm8921" - #address-cells: diff --git a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt index 485bc59fcc48..3c91ad430eea 100644 --- a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt +++ b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt @@ -234,7 +234,7 @@ see regulator.txt - with additional custom properties described below: - qcom,switch-mode-frequency: Usage: required Value type: <u32> - Definition: Frequency (Hz) of the swith mode power supply; + Definition: Frequency (Hz) of the switch mode power supply; must be one of: 19200000, 9600000, 6400000, 4800000, 3840000, 3200000, 2740000, 2400000, 2130000, 1920000, 1750000, 1600000, diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt index 9e6770b105c9..65c23263cc54 100644 --- a/Documentation/devicetree/bindings/mfd/rn5t618.txt +++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt @@ -1,21 +1,25 @@ * Ricoh RN5T567/RN5T618 PMIC -Ricoh RN5T567/RN5T618 is a power management IC family which integrates -3 to 4 step-down DCDC converters, 7 low-dropout regulators, GPIOs and -a watchdog timer. The RN5T618 provides additionally a Li-ion battery -charger, fuel gauge and an ADC. It can be controlled through an I2C -interface. +Ricoh RN5T567/RN5T618/RC5T619 is a power management IC family which +integrates 3 to 5 step-down DCDC converters, 7 to 10 low-dropout regulators, +GPIOs, and a watchdog timer. It can be controlled through an I2C interface. +The RN5T618/RC5T619 provides additionally a Li-ion battery charger, +fuel gauge, and an ADC. +The RC5T619 additionnally includes USB charger detection and an RTC. Required properties: - compatible: must be one of "ricoh,rn5t567" "ricoh,rn5t618" + "ricoh,rc5t619" - reg: the I2C slave address of the device Sub-nodes: - regulators: the node is required if the regulator functionality is needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, DCDC4 - (RN5T567), LDO1, LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2. + (RN5T567/RC5T619), LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7, LDO8, + LDO9, LDO10, LDORTC1 and LDORTC2. + LDO7-10 are specific to RC5T619. The common bindings for each individual regulator can be found in: Documentation/devicetree/bindings/regulator/regulator.txt diff --git a/Documentation/devicetree/bindings/mfd/stm32-timers.txt b/Documentation/devicetree/bindings/mfd/stm32-timers.txt new file mode 100644 index 000000000000..bbd083f5600a --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/stm32-timers.txt @@ -0,0 +1,46 @@ +STM32 Timers driver bindings + +This IP provides 3 types of timer along with PWM functionality: +- advanced-control timers consist of a 16-bit auto-reload counter driven by a programmable + prescaler, break input feature, PWM outputs and complementary PWM ouputs channels. +- general-purpose timers consist of a 16-bit or 32-bit auto-reload counter driven by a + programmable prescaler and PWM outputs. +- basic timers consist of a 16-bit auto-reload counter driven by a programmable prescaler. + +Required parameters: +- compatible: must be "st,stm32-timers" + +- reg: Physical base address and length of the controller's + registers. +- clock-names: Set to "int". +- clocks: Phandle to the clock used by the timer module. + For Clk properties, please refer to ../clock/clock-bindings.txt + +Optional parameters: +- resets: Phandle to the parent reset controller. + See ../reset/st,stm32-rcc.txt + +Optional subnodes: +- pwm: See ../pwm/pwm-stm32.txt +- timer: See ../iio/timer/stm32-timer-trigger.txt + +Example: + timers@40010000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40010000 0x400>; + clocks = <&rcc 0 160>; + clock-names = "clk_int"; + + pwm { + compatible = "st,stm32-pwm"; + pinctrl-0 = <&pwm1_pins>; + pinctrl-names = "default"; + }; + + timer@0 { + compatible = "st,stm32-timer-trigger"; + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/tps65086.txt b/Documentation/devicetree/bindings/mfd/tps65086.txt index d3705612a846..9cfa886fe99f 100644 --- a/Documentation/devicetree/bindings/mfd/tps65086.txt +++ b/Documentation/devicetree/bindings/mfd/tps65086.txt @@ -23,7 +23,7 @@ Required properties: defined below. Optional regulator properties: - - ti,regulator-step-size-25mv : This is applicable for buck[1,2,6], set this + - ti,regulator-step-size-25mv : This is applicable for buck[1-6], set this if the regulator is factory set with a 25mv step voltage mapping. - ti,regulator-decay : This is applicable for buck[1-6], set this if diff --git a/Documentation/devicetree/bindings/mips/img/pistachio-marduk.txt b/Documentation/devicetree/bindings/mips/img/pistachio-marduk.txt new file mode 100644 index 000000000000..2d5126d529a2 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/img/pistachio-marduk.txt @@ -0,0 +1,10 @@ +Imagination Technologies' Pistachio SoC based Marduk Board +========================================================== + +Compatible string must be "img,pistachio-marduk", "img,pistachio" + +Hardware and other related documentation is available at +https://docs.creatordev.io/ci40/ + +It is also known as Creator Ci40. Marduk is legacy name and will +be there for decades. diff --git a/Documentation/devicetree/bindings/misc/atmel-ssc.txt b/Documentation/devicetree/bindings/misc/atmel-ssc.txt index efc98ea1f23d..f8629bb73945 100644 --- a/Documentation/devicetree/bindings/misc/atmel-ssc.txt +++ b/Documentation/devicetree/bindings/misc/atmel-ssc.txt @@ -24,6 +24,8 @@ Optional properties: this parameter to choose where the clock from. - By default the clock is from TK pin, if the clock from RK pin, this property is needed. + - #sound-dai-cells: Should contain <0>. + - This property makes the SSC into an automatically registered DAI. Examples: - PDC transfer: diff --git a/Documentation/devicetree/bindings/misc/idt_89hpesx.txt b/Documentation/devicetree/bindings/misc/idt_89hpesx.txt new file mode 100644 index 000000000000..b9093b79ab7d --- /dev/null +++ b/Documentation/devicetree/bindings/misc/idt_89hpesx.txt @@ -0,0 +1,44 @@ +EEPROM / CSR SMBus-slave interface of IDT 89HPESx devices + +Required properties: + - compatible : should be "<manufacturer>,<type>" + Basically there is only one manufacturer: idt, but some + compatible devices may be produced in future. Following devices + are supported: 89hpes8nt2, 89hpes12nt3, 89hpes24nt6ag2, + 89hpes32nt8ag2, 89hpes32nt8bg2, 89hpes12nt12g2, 89hpes16nt16g2, + 89hpes24nt24g2, 89hpes32nt24ag2, 89hpes32nt24bg2; + 89hpes12n3, 89hpes12n3a, 89hpes24n3, 89hpes24n3a; + 89hpes32h8, 89hpes32h8g2, 89hpes48h12, 89hpes48h12g2, + 89hpes48h12ag2, 89hpes16h16, 89hpes22h16, 89hpes22h16g2, + 89hpes34h16, 89hpes34h16g2, 89hpes64h16, 89hpes64h16g2, + 89hpes64h16ag2; + 89hpes12t3g2, 89hpes24t3g2, 89hpes16t4, 89hpes4t4g2, + 89hpes10t4g2, 89hpes16t4g2, 89hpes16t4ag2, 89hpes5t5, + 89hpes6t5, 89hpes8t5, 89hpes8t5a, 89hpes24t6, 89hpes6t6g2, + 89hpes24t6g2, 89hpes16t7, 89hpes32t8, 89hpes32t8g2, + 89hpes48t12, 89hpes48t12g2. + - reg : I2C address of the IDT 89HPESx device. + +Optionally there can be EEPROM-compatible subnode: + - compatible: There are five EEPROM devices supported: 24c32, 24c64, 24c128, + 24c256 and 24c512 differed by size. + - reg: Custom address of EEPROM device (If not specified IDT 89HPESx + (optional) device will try to communicate with EEPROM sited by default + address - 0x50) + - read-only : Parameterless property disables writes to the EEPROM + (optional) + +Example: + idt@60 { + compatible = "idt,89hpes32nt8ag2"; + reg = <0x74>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@50 { + compatible = "onsemi,24c64"; + reg = <0x50>; + read-only; + }; + }; + diff --git a/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt new file mode 100644 index 000000000000..50bf611a4d2c --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt @@ -0,0 +1,32 @@ +Amlogic SD / eMMC controller for S905/GXBB family SoCs + +The MMC 5.1 compliant host controller on Amlogic provides the +interface for SD, eMMC and SDIO devices. + +This file documents the properties in addition to those available in +the MMC core bindings, documented by mmc.txt. + +Required properties: +- compatible : contains one of: + - "amlogic,meson-gx-mmc" + - "amlogic,meson-gxbb-mmc" + - "amlogic,meson-gxl-mmc" + - "amlogic,meson-gxm-mmc" +- clocks : A list of phandle + clock-specifier pairs for the clocks listed in clock-names. +- clock-names: Should contain the following: + "core" - Main peripheral bus clock + "clkin0" - Parent clock of internal mux + "clkin1" - Other parent clock of internal mux + The driver has an internal mux clock which switches between clkin0 and clkin1 depending on the + clock rate requested by the MMC core. + +Example: + + sd_emmc_a: mmc@70000 { + compatible = "amlogic,meson-gxbb-mmc"; + reg = <0x0 0x70000 0x0 0x2000>; + interrupts = < GIC_SPI 216 IRQ_TYPE_EDGE_RISING>; + clocks = <&clkc CLKID_SD_EMMC_A>, <&xtal>, <&clkc CLKID_FCLK_DIV2>; + clock-names = "core", "clkin0", "clkin1"; + pinctrl-0 = <&emmc_pins>; + }; diff --git a/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt b/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt index be56d2bd474a..954561d09a8e 100644 --- a/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt +++ b/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt @@ -7,6 +7,15 @@ Required properties: - compatible : Should be one of the following "brcm,bcm2835-sdhci" "brcm,sdhci-iproc-cygnus" + "brcm,sdhci-iproc" + +Use brcm2835-sdhci for Rasperry PI. + +Use sdhci-iproc-cygnus for Broadcom SDHCI Controllers +restricted to 32bit host accesses to SDHCI registers. + +Use sdhci-iproc for Broadcom SDHCI Controllers that allow standard +8, 16, 32-bit host access to SDHCI register. - clocks : The clock feeding the SDHCI controller. diff --git a/Documentation/devicetree/bindings/mmc/mmc-pwrseq-sd8787.txt b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-sd8787.txt new file mode 100644 index 000000000000..22e9340e4ba2 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-sd8787.txt @@ -0,0 +1,16 @@ +* Marvell SD8787 power sequence provider + +Required properties: +- compatible: must be "mmc-pwrseq-sd8787". +- powerdown-gpios: contains a power down GPIO specifier with the + default active state +- reset-gpios: contains a reset GPIO specifier with the default + active state + +Example: + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-sd8787"; + powerdown-gpios = <&twl_gpio 0 GPIO_ACTIVE_LOW>; + reset-gpios = <&twl_gpio 1 GPIO_ACTIVE_LOW>; + } diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 8a377827695b..c7f4a0ec48ed 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -40,6 +40,7 @@ Optional properties: - cap-mmc-hw-reset: eMMC hardware reset is supported - cap-sdio-irq: enable SDIO IRQ signalling on this interface - full-pwr-cycle: full power cycle of the card is supported +- mmc-ddr-3_3v: eMMC high-speed DDR mode(3.3V I/O) is supported - mmc-ddr-1_8v: eMMC high-speed DDR mode(1.8V I/O) is supported - mmc-ddr-1_2v: eMMC high-speed DDR mode(1.2V I/O) is supported - mmc-hs200-1_8v: eMMC HS200 mode(1.8V I/O) is supported diff --git a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt index ff611fa66871..e4ba92aa035e 100644 --- a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt +++ b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt @@ -8,11 +8,14 @@ Required properties: - compatible: should be "renesas,mmcif-<soctype>", "renesas,sh-mmcif" as a fallback. Examples with <soctype> are: + - "renesas,mmcif-r8a73a4" for the MMCIF found in r8a73a4 SoCs - "renesas,mmcif-r8a7740" for the MMCIF found in r8a7740 SoCs + - "renesas,mmcif-r8a7778" for the MMCIF found in r8a7778 SoCs - "renesas,mmcif-r8a7790" for the MMCIF found in r8a7790 SoCs - "renesas,mmcif-r8a7791" for the MMCIF found in r8a7791 SoCs - "renesas,mmcif-r8a7793" for the MMCIF found in r8a7793 SoCs - "renesas,mmcif-r8a7794" for the MMCIF found in r8a7794 SoCs + - "renesas,mmcif-sh73a0" for the MMCIF found in sh73a0 SoCs - clocks: reference to the functional clock diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt index 07184e8f894e..ea9c1c9607f6 100644 --- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt @@ -13,6 +13,7 @@ Required Properties: - "rockchip,rk2928-dw-mshc": for Rockchip RK2928 and following, before RK3288 - "rockchip,rk3288-dw-mshc": for Rockchip RK3288 + - "rockchip,rk1108-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK1108 - "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3036 - "rockchip,rk3368-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3368 - "rockchip,rk3399-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3399 diff --git a/Documentation/devicetree/bindings/mmc/sdhci-cadence.txt b/Documentation/devicetree/bindings/mmc/sdhci-cadence.txt new file mode 100644 index 000000000000..c0f37cb41a9b --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-cadence.txt @@ -0,0 +1,32 @@ +* Cadence SD/SDIO/eMMC Host Controller + +Required properties: +- compatible: should be one of the following: + "cdns,sd4hc" - default of the IP + "socionext,uniphier-sd4hc" - for Socionext UniPhier SoCs +- reg: offset and length of the register set for the device. +- interrupts: a single interrupt specifier. +- clocks: phandle to the input clock. + +Optional properties: +For eMMC configuration, supported speed modes are not indicated by the SDHCI +Capabilities Register. Instead, the following properties should be specified +if supported. See mmc.txt for details. +- mmc-ddr-1_8v +- mmc-ddr-1_2v +- mmc-hs200-1_8v +- mmc-hs200-1_2v +- mmc-hs400-1_8v +- mmc-hs400-1_2v + +Example: + emmc: sdhci@5a000000 { + compatible = "socionext,uniphier-sd4hc", "cdns,sd4hc"; + reg = <0x5a000000 0x400>; + interrupts = <0 78 4>; + clocks = <&clk 4>; + bus-width = <8>; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + }; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt index 485483a63d8c..0576264eab5e 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt @@ -17,6 +17,7 @@ Required properties: "iface" - Main peripheral bus clock (PCLK/HCLK - AHB Bus clock) (required) "core" - SDC MMC clock (MCLK) (required) "bus" - SDCC bus voter clock (optional) + "xo" - TCXO clock (optional) Example: diff --git a/Documentation/devicetree/bindings/mmc/sdhci-st.txt b/Documentation/devicetree/bindings/mmc/sdhci-st.txt index 3cd4c43a3260..230fd696eb92 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-st.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-st.txt @@ -38,7 +38,7 @@ Optional properties: - bus-width: Number of data lines. See: Documentation/devicetree/bindings/mmc/mmc.txt. -- max-frequency: Can be 200MHz, 100Mz or 50MHz (default) and used for +- max-frequency: Can be 200MHz, 100MHz or 50MHz (default) and used for configuring the CCONFIG3 in the mmcss. See: Documentation/devicetree/bindings/mmc/mmc.txt. diff --git a/Documentation/devicetree/bindings/mmc/sdhci.txt b/Documentation/devicetree/bindings/mmc/sdhci.txt new file mode 100644 index 000000000000..0e9923a64024 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci.txt @@ -0,0 +1,13 @@ +The properties specific for SD host controllers. For properties shared by MMC +host controllers refer to the mmc[1] bindings. + + [1] Documentation/devicetree/bindings/mmc/mmc.txt + +Optional properties: +- sdhci-caps-mask: The sdhci capabilities register is incorrect. This 64bit + property corresponds to the bits in the sdhci capability register. If the bit + is on in the mask then the bit is incorrect in the register and should be + turned off, before applying sdhci-caps. +- sdhci-caps: The sdhci capabilities register is incorrect. This 64bit + property corresponds to the bits in the sdhci capability register. If the + bit is on in the property then the bit should be turned on. diff --git a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt index 55cdd804cdba..7d53a799f140 100644 --- a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt +++ b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt @@ -13,6 +13,7 @@ Required properties: * "allwinner,sun5i-a13-mmc" * "allwinner,sun7i-a20-mmc" * "allwinner,sun9i-a80-mmc" + * "allwinner,sun50i-a64-emmc" * "allwinner,sun50i-a64-mmc" - reg : mmc controller base registers - clocks : a list with 4 phandle + clock specifier pairs diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt index bfa461aaac99..9cb55ca57461 100644 --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt @@ -16,7 +16,7 @@ Required Properties: each child-node representing a supported slot. There should be atleast one child node representing a card slot. The name of the child node representing the slot is recommended to be slot@n where n is the unique number of the slot - connnected to the controller. The following are optional properties which + connected to the controller. The following are optional properties which can be included in the slot child node. * reg: specifies the physical slot number. The valid values of this @@ -59,8 +59,9 @@ Optional properties: is specified and the ciu clock is specified then we'll try to set the ciu clock to this at probe time. -* clock-freq-min-max: Minimum and Maximum clock frequency for card output +* clock-freq-min-max (DEPRECATED): Minimum and Maximum clock frequency for card output clock(cclk_out). If it's not specified, max is 200MHZ and min is 400KHz by default. + (Use the "max-frequency" instead of "clock-freq-min-max".) * num-slots: specifies the number of slots supported by the controller. The number of physical slots actually used could be equal or less than the @@ -74,10 +75,16 @@ Optional properties: * card-detect-delay: Delay in milli-seconds before detecting card after card insert event. The default value is 0. -* supports-highspeed (DEPRECATED): Enables support for high speed cards (up to 50MHz) - (use "cap-mmc-highspeed" or "cap-sd-highspeed" instead) +* data-addr: Override fifo address with value provided by DT. The default FIFO reg + offset is assumed as 0x100 (version < 0x240A) and 0x200(version >= 0x240A) by + driver. If the controller does not follow this rule, please use this property + to set fifo address in device tree. -* broken-cd: as documented in mmc core bindings. +* fifo-watermark-aligned: Data done irq is expected if data length is less than + watermark in PIO mode. But fifo watermark is requested to be aligned with data + length in some SoC so that TX/RX irq can be generated with data done irq. Add this + watermark quirk to mark this requirement and force fifo watermark setting + accordingly. * vmmc-supply: The phandle to the regulator to use for vmmc. If this is specified we'll defer probe until we can find this regulator. @@ -106,6 +113,8 @@ board specific portions as listed below. interrupts = <0 75 0>; #address-cells = <1>; #size-cells = <0>; + data-addr = <0x200>; + fifo-watermark-aligned; resets = <&rst 20>; reset-names = "reset"; }; diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index 13df9c2399c3..4fd8b7acc510 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -11,8 +11,8 @@ optional bindings can be used. Required properties: - compatible: "renesas,sdhi-shmobile" - a generic sh-mobile SDHI unit - "renesas,sdhi-sh7372" - SDHI IP on SH7372 SoC "renesas,sdhi-sh73a0" - SDHI IP on SH73A0 SoC + "renesas,sdhi-r7s72100" - SDHI IP on R7S72100 SoC "renesas,sdhi-r8a73a4" - SDHI IP on R8A73A4 SoC "renesas,sdhi-r8a7740" - SDHI IP on R8A7740 SoC "renesas,sdhi-r8a7778" - SDHI IP on R8A7778 SoC @@ -25,6 +25,19 @@ Required properties: "renesas,sdhi-r8a7795" - SDHI IP on R8A7795 SoC "renesas,sdhi-r8a7796" - SDHI IP on R8A7796 SoC +- clocks: Most controllers only have 1 clock source per channel. However, on + some variations of this controller, the internal card detection + logic that exists in this controller is sectioned off to be run by a + separate second clock source to allow the main core clock to be turned + off to save power. + If 2 clocks are specified by the hardware, you must name them as + "core" and "cd". If the controller only has 1 clock, naming is not + required. + Below is the number clocks for each supported SoC: + 1: SH73A0, R8A73A4, R8A7740, R8A7778, R8A7779, R8A7790 + R8A7791, R8A7792, R8A7793, R8A7794, R8A7795, R8A7796 + 2: R7S72100 + Optional properties: - toshiba,mmc-wrprotect-disable: write-protect detection is unavailable - pinctrl-names: should be "default", "state_uhs" diff --git a/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt new file mode 100644 index 000000000000..eaade0e5adeb --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt @@ -0,0 +1,33 @@ +* ZTE specific extensions to the Synopsys Designware Mobile Storage + Host Controller + +The Synopsys designware mobile storage host controller is used to interface +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents +differences between the core Synopsys dw mshc controller properties described +by synopsys-dw-mshc.txt and the properties used by the ZTE specific +extensions to the Synopsys Designware Mobile Storage Host Controller. + +Required Properties: + +* compatible: should be + - "zte,zx296718-dw-mshc": for ZX SoCs + +Example: + + mmc1: mmc@1110000 { + compatible = "zte,zx296718-dw-mshc"; + reg = <0x01110000 0x1000>; + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; + fifo-depth = <32>; + data-addr = <0x200>; + fifo-watermark-aligned; + bus-width = <4>; + clock-frequency = <50000000>; + clocks = <&topcrm SD0_AHB>, <&topcrm SD0_WCLK>; + clock-names = "biu", "ciu"; + num-slots = <1>; + max-frequency = <50000000>; + cap-sdio-irq; + cap-sd-highspeed; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/mtd/aspeed-smc.txt b/Documentation/devicetree/bindings/mtd/aspeed-smc.txt new file mode 100644 index 000000000000..49f6528ef547 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/aspeed-smc.txt @@ -0,0 +1,51 @@ +* Aspeed Firmware Memory controller +* Aspeed SPI Flash Memory Controller + +The Firmware Memory Controller in the Aspeed AST2500 SoC supports +three chip selects, two of which are always of SPI type and the third +can be SPI or NOR type flash. These bindings only describe SPI. + +The two SPI flash memory controllers in the AST2500 each support two +chip selects. + +Required properties: + - compatible : Should be one of + "aspeed,ast2400-fmc" for the AST2400 Firmware Memory Controller + "aspeed,ast2400-spi" for the AST2400 SPI Flash memory Controller + "aspeed,ast2500-fmc" for the AST2500 Firmware Memory Controller + "aspeed,ast2500-spi" for the AST2500 SPI flash memory controllers + + - reg : the first contains the control register location and length, + the second contains the memory window mapping address and length + - #address-cells : must be 1 corresponding to chip select child binding + - #size-cells : must be 0 corresponding to chip select child binding + +Optional properties: + - interrupts : Should contain the interrupt for the dma device if an + FMC + +The child nodes are the SPI flash modules which must have a compatible +property as specified in bindings/mtd/jedec,spi-nor.txt + +Optionally, the child node can contain properties for SPI mode (may be +ignored): + - spi-max-frequency - max frequency of spi bus + + +Example: +fmc: fmc@1e620000 { + compatible = "aspeed,ast2500-fmc"; + reg = < 0x1e620000 0x94 + 0x20000000 0x02000000 >; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <19>; + flash@0 { + reg = < 0 >; + compatible = "jedec,spi-nor"; + /* spi-max-frequency = <>; */ + /* m25p,fast-read; */ + #address-cells = <1>; + #size-cells = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/common.txt b/Documentation/devicetree/bindings/mtd/common.txt new file mode 100644 index 000000000000..fc068b923d7a --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/common.txt @@ -0,0 +1,15 @@ +* Common properties of all MTD devices + +Optional properties: +- label: user-defined MTD device name. Can be used to assign user + friendly names to MTD devices (instead of the flash model or flash + controller based name) in order to ease flash device identification + and/or describe what they are used for. + +Example: + + flash@0 { + label = "System-firmware"; + + /* flash type specific properties */ + }; diff --git a/Documentation/devicetree/bindings/mtd/cortina,gemini-flash.txt b/Documentation/devicetree/bindings/mtd/cortina,gemini-flash.txt new file mode 100644 index 000000000000..3fa1b34d69ad --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/cortina,gemini-flash.txt @@ -0,0 +1,24 @@ +Flash device on Cortina Systems Gemini SoC + +This flash is regular CFI compatible (Intel or AMD extended) flash chips with +some special bits that can be controlled by the machine's system controller. + +Required properties: +- compatible : must be "cortina,gemini-flash", "cfi-flash"; +- reg : memory address for the flash chip +- syscon : must be a phandle to the system controller +- bank-width : width in bytes of flash interface, should be <2> + +For the rest of the properties, see mtd-physmap.txt. + +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + +Example: + +flash@30000000 { + compatible = "cortina,gemini-flash", "cfi-flash"; + reg = <0x30000000 0x01000000>; + syscon = <&syscon>; + bank-width = <2>; +}; diff --git a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt index 2c91c03e7eb0..3e920ec5c4d3 100644 --- a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt +++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt @@ -14,6 +14,8 @@ Required properties: at25df641 at26df081a mr25h256 + mr25h10 + mr25h40 mx25l4005a mx25l1606e mx25l6405d diff --git a/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt b/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt index fb314f09861b..5ded66ad7aef 100644 --- a/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt +++ b/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt @@ -1,7 +1,13 @@ * Serial NOR flash controller for MTK MT81xx (and similar) Required properties: -- compatible: should be "mediatek,mt8173-nor"; +- compatible: The possible values are: + "mediatek,mt2701-nor" + "mediatek,mt7623-nor" + "mediatek,mt8173-nor" + For mt8173, compatible should be "mediatek,mt8173-nor". + For every other SoC, should contain both the SoC-specific compatible string + and "mediatek,mt8173-nor". - reg: physical base address and length of the controller's register - clocks: the phandle of the clocks needed by the nor controller - clock-names: the names of the clocks diff --git a/Documentation/devicetree/bindings/mtd/oxnas-nand.txt b/Documentation/devicetree/bindings/mtd/oxnas-nand.txt new file mode 100644 index 000000000000..56d5c19da41d --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/oxnas-nand.txt @@ -0,0 +1,41 @@ +* Oxford Semiconductor OXNAS NAND Controller + +Please refer to nand.txt for generic information regarding MTD NAND bindings. + +Required properties: + - compatible: "oxsemi,ox820-nand" + - reg: Base address and length for NAND mapped memory. + +Optional Properties: + - clocks: phandle to the NAND gate clock if needed. + - resets: phandle to the NAND reset control if needed. + +Example: + +nandc: nand-controller@41000000 { + compatible = "oxsemi,ox820-nand"; + reg = <0x41000000 0x100000>; + clocks = <&stdclk CLK_820_NAND>; + resets = <&reset RESET_NAND>; + #address-cells = <1>; + #size-cells = <0>; + + nand@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + nand-ecc-mode = "soft"; + nand-ecc-algo = "hamming"; + + partition@0 { + label = "boot"; + reg = <0x00000000 0x00e00000>; + read-only; + }; + + partition@e00000 { + label = "ubi"; + reg = <0x00e00000 0x07200000>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/samsung-s3c2410.txt b/Documentation/devicetree/bindings/mtd/samsung-s3c2410.txt new file mode 100644 index 000000000000..0040eb8895e0 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/samsung-s3c2410.txt @@ -0,0 +1,56 @@ +* Samsung S3C2410 and compatible NAND flash controller + +Required properties: +- compatible : The possible values are: + "samsung,s3c2410-nand" + "samsung,s3c2412-nand" + "samsung,s3c2440-nand" +- reg : register's location and length. +- #address-cells, #size-cells : see nand.txt +- clocks : phandle to the nand controller clock +- clock-names : must contain "nand" + +Optional child nodes: +Child nodes representing the available nand chips. + +Optional child properties: +- nand-ecc-mode : see nand.txt +- nand-on-flash-bbt : see nand.txt + +Each child device node may optionally contain a 'partitions' sub-node, +which further contains sub-nodes describing the flash partition mapping. +See partition.txt for more detail. + +Example: + +nand-controller@4e000000 { + compatible = "samsung,s3c2440-nand"; + reg = <0x4e000000 0x40>; + + #address-cells = <1>; + #size-cells = <0>; + + clocks = <&clocks HCLK_NAND>; + clock-names = "nand"; + + nand { + nand-ecc-mode = "soft"; + nand-on-flash-bbt; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0 0x040000>; + }; + + partition@40000 { + label = "kernel"; + reg = <0x040000 0x500000>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/tango-nand.txt b/Documentation/devicetree/bindings/mtd/tango-nand.txt new file mode 100644 index 000000000000..cd1bf2ac9055 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/tango-nand.txt @@ -0,0 +1,38 @@ +Sigma Designs Tango4 NAND Flash Controller (NFC) + +Required properties: + +- compatible: "sigma,smp8758-nand" +- reg: address/size of nfc_reg, nfc_mem, and pbus_reg +- dmas: reference to the DMA channel used by the controller +- dma-names: "rxtx" +- clocks: reference to the system clock +- #address-cells: <1> +- #size-cells: <0> + +Children nodes represent the available NAND chips. +See Documentation/devicetree/bindings/mtd/nand.txt for generic bindings. + +Example: + + nandc: nand-controller@2c000 { + compatible = "sigma,smp8758-nand"; + reg = <0x2c000 0x30>, <0x2d000 0x800>, <0x20000 0x1000>; + dmas = <&dma0 3>; + dma-names = "rxtx"; + clocks = <&clkgen SYS_CLK>; + #address-cells = <1>; + #size-cells = <0>; + + nand@0 { + reg = <0>; /* CS0 */ + nand-ecc-strength = <14>; + nand-ecc-step-size = <1024>; + }; + + nand@1 { + reg = <1>; /* CS1 */ + nand-ecc-strength = <14>; + nand-ecc-step-size = <1024>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/brcm,amac.txt b/Documentation/devicetree/bindings/net/brcm,amac.txt index ba5ecc1041a5..2fefa1a44afd 100644 --- a/Documentation/devicetree/bindings/net/brcm,amac.txt +++ b/Documentation/devicetree/bindings/net/brcm,amac.txt @@ -2,11 +2,17 @@ Broadcom AMAC Ethernet Controller Device Tree Bindings ------------------------------------------------------------- Required properties: - - compatible: "brcm,amac" or "brcm,nsp-amac" - - reg: Address and length of the GMAC registers, - Address and length of the GMAC IDM registers - - reg-names: Names of the registers. Must have both "amac_base" and - "idm_base" + - compatible: "brcm,amac" + "brcm,nsp-amac" + "brcm,ns2-amac" + - reg: Address and length of the register set for the device. It + contains the information of registers in the same order as + described by reg-names + - reg-names: Names of the registers. + "amac_base": Address and length of the GMAC registers + "idm_base": Address and length of the GMAC IDM registers + "nicpm_base": Address and length of the NIC Port Manager + registers (required for Northstar2) - interrupts: Interrupt number Optional properties: diff --git a/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt b/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt index fb40891ee606..9a734d808aa7 100644 --- a/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt +++ b/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt @@ -2,7 +2,7 @@ Required properties: -- compatible: should be "brcm,bcm7445-switch-v4.0" +- compatible: should be "brcm,bcm7445-switch-v4.0" or "brcm,bcm7278-switch-v4.0" - reg: addresses and length of the register sets for the device, must be 6 pairs of register addresses and lengths - interrupts: interrupts for the devices, must be two interrupts @@ -41,6 +41,13 @@ Optional properties: Admission Control Block supports reporting the number of packets in-flight in a switch queue +Port subnodes: + +Optional properties: + +- brcm,use-bcm-hdr: boolean property, if present, indicates that the switch + port has Broadcom tags enabled (per-packet metadata) + Example: switch_top@f0b00000 { @@ -114,6 +121,7 @@ switch_top@f0b00000 { port@0 { label = "gphy"; reg = <0>; + brcm,use-bcm-hdr; }; ... }; diff --git a/Documentation/devicetree/bindings/net/brcm,systemport.txt b/Documentation/devicetree/bindings/net/brcm,systemport.txt index 877da34145b0..83f29e0e11ba 100644 --- a/Documentation/devicetree/bindings/net/brcm,systemport.txt +++ b/Documentation/devicetree/bindings/net/brcm,systemport.txt @@ -1,7 +1,10 @@ * Broadcom BCM7xxx Ethernet Systemport Controller (SYSTEMPORT) Required properties: -- compatible: should be one of "brcm,systemport-v1.00" or "brcm,systemport" +- compatible: should be one of: + "brcm,systemport-v1.00" + "brcm,systemportlite-v1.00" or + "brcm,systemport" - reg: address and length of the register set for the device. - interrupts: interrupts for the device, first cell must be for the rx interrupts, and the second cell should be for the transmit queues. An diff --git a/Documentation/devicetree/bindings/net/btusb.txt b/Documentation/devicetree/bindings/net/btusb.txt new file mode 100644 index 000000000000..01fa2d4188d4 --- /dev/null +++ b/Documentation/devicetree/bindings/net/btusb.txt @@ -0,0 +1,43 @@ +Generic Bluetooth controller over USB (btusb driver) +--------------------------------------------------- + +Required properties: + + - compatible : should comply with the format "usbVID,PID" specified in + Documentation/devicetree/bindings/usb/usb-device.txt + At the time of writing, the only OF supported devices + (more may be added later) are: + + "usb1286,204e" (Marvell 8997) + +Also, vendors that use btusb may have device additional properties, e.g: +Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt + +Optional properties: + + - interrupt-parent: phandle of the parent interrupt controller + - interrupt-names: (see below) + - interrupts : The interrupt specified by the name "wakeup" is the interrupt + that shall be used for out-of-band wake-on-bt. Driver will + request this interrupt for wakeup. During system suspend, the + irq will be enabled so that the bluetooth chip can wakeup host + platform out of band. During system resume, the irq will be + disabled to make sure unnecessary interrupt is not received. + +Example: + +Following example uses irq pin number 3 of gpio0 for out of band wake-on-bt: + +&usb_host1_ehci { + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + + mvl_bt1: bt@1 { + compatible = "usb1286,204e"; + reg = <1>; + interrupt-parent = <&gpio0>; + interrupt-name = "wakeup"; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/can/rcar_can.txt b/Documentation/devicetree/bindings/net/can/rcar_can.txt index 8d40ab27bc8c..06bb7cc334c8 100644 --- a/Documentation/devicetree/bindings/net/can/rcar_can.txt +++ b/Documentation/devicetree/bindings/net/can/rcar_can.txt @@ -10,6 +10,7 @@ Required properties: "renesas,can-r8a7793" if CAN controller is a part of R8A7793 SoC. "renesas,can-r8a7794" if CAN controller is a part of R8A7794 SoC. "renesas,can-r8a7795" if CAN controller is a part of R8A7795 SoC. + "renesas,can-r8a7796" if CAN controller is a part of R8A7796 SoC. "renesas,rcar-gen1-can" for a generic R-Car Gen1 compatible device. "renesas,rcar-gen2-can" for a generic R-Car Gen2 compatible device. "renesas,rcar-gen3-can" for a generic R-Car Gen3 compatible device. @@ -24,11 +25,12 @@ Required properties: - pinctrl-0: pin control group to be used for this controller. - pinctrl-names: must be "default". -Required properties for "renesas,can-r8a7795" compatible: -In R8A7795 SoC, "clkp2" can be CANFD clock. This is a div6 clock and can be -used by both CAN and CAN FD controller at the same time. It needs to be scaled -to maximum frequency if any of these controllers use it. This is done using -the below properties. +Required properties for "renesas,can-r8a7795" and "renesas,can-r8a7796" +compatible: +In R8A7795 and R8A7796 SoCs, "clkp2" can be CANFD clock. This is a div6 clock +and can be used by both CAN and CAN FD controller at the same time. It needs to +be scaled to maximum frequency if any of these controllers use it. This is done +using the below properties: - assigned-clocks: phandle of clkp2(CANFD) clock. - assigned-clock-rates: maximum frequency of this clock. diff --git a/Documentation/devicetree/bindings/net/can/rcar_canfd.txt b/Documentation/devicetree/bindings/net/can/rcar_canfd.txt index 22a6f10bab05..93c3a6ae32f9 100644 --- a/Documentation/devicetree/bindings/net/can/rcar_canfd.txt +++ b/Documentation/devicetree/bindings/net/can/rcar_canfd.txt @@ -5,13 +5,14 @@ Required properties: - compatible: Must contain one or more of the following: - "renesas,rcar-gen3-canfd" for R-Car Gen3 compatible controller. - "renesas,r8a7795-canfd" for R8A7795 (R-Car H3) compatible controller. + - "renesas,r8a7796-canfd" for R8A7796 (R-Car M3) compatible controller. When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first, followed by the family-specific and/or generic versions. - reg: physical base address and size of the R-Car CAN FD register map. -- interrupts: interrupt specifier for the Global & Channel interrupts +- interrupts: interrupt specifiers for the Channel & Global interrupts - clocks: phandles and clock specifiers for 3 clock inputs. - clock-names: 3 clock input name strings: "fck", "canfd", "can_clk". - pinctrl-0: pin control group to be used for this controller. @@ -23,11 +24,12 @@ The name of the child nodes are "channel0" and "channel1" respectively. Each child node supports the "status" property only, which is used to enable/disable the respective channel. -Required properties for "renesas,r8a7795-canfd" compatible: -In R8A7795 SoC, canfd clock is a div6 clock and can be used by both CAN -and CAN FD controller at the same time. It needs to be scaled to maximum -frequency if any of these controllers use it. This is done using the -below properties. +Required properties for "renesas,r8a7795-canfd" and "renesas,r8a7796-canfd" +compatible: +In R8A7795 and R8A7796 SoCs, canfd clock is a div6 clock and can be used by both +CAN and CAN FD controller at the same time. It needs to be scaled to maximum +frequency if any of these controllers use it. This is done using the below +properties: - assigned-clocks: phandle of canfd clock. - assigned-clock-rates: maximum frequency of this clock. diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index 5ad439f30135..7cc15c96ea95 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -20,12 +20,9 @@ Required properties: - slaves : Specifies number for slaves - active_slave : Specifies the slave to use for time stamping, ethtool and SIOCGMIIPHY -- cpts_clock_mult : Numerator to convert input clock ticks into nanoseconds -- cpts_clock_shift : Denominator to convert input clock ticks into nanoseconds Optional properties: - ti,hwmods : Must be "cpgmac0" -- no_bd_ram : Must be 0 or 1 - dual_emac : Specifies Switch to act as Dual EMAC - syscon : Phandle to the system control device node, which is the control module device of the am33x @@ -35,7 +32,11 @@ Optional properties: For example in dra72x-evm, pcf gpio has to be driven low so that cpsw slave 0 and phy data lines are connected via mux. - +- cpts_clock_mult : Numerator to convert input clock ticks into nanoseconds +- cpts_clock_shift : Denominator to convert input clock ticks into nanoseconds + Mult and shift will be calculated basing on CPTS + rftclk frequency if both cpts_clock_shift and + cpts_clock_mult properties are not provided. Slave Properties: Required properties: @@ -68,7 +69,6 @@ Examples: cpdma_channels = <8>; ale_entries = <1024>; bd_ram_size = <0x2000>; - no_bd_ram = <0>; rx_descs = <64>; mac_control = <0x20>; slaves = <2>; @@ -97,7 +97,6 @@ Examples: cpdma_channels = <8>; ale_entries = <1024>; bd_ram_size = <0x2000>; - no_bd_ram = <0>; rx_descs = <64>; mac_control = <0x20>; slaves = <2>; diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt index a4a570fb2494..cfe8f64eca4f 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa.txt +++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt @@ -34,13 +34,9 @@ Required properties: Each port children node must have the following mandatory properties: - reg : Describes the port address in the switch -- label : Describes the label associated with this port, which - will become the netdev name. Special labels are - "cpu" to indicate a CPU port and "dsa" to - indicate an uplink/downlink port between switches in - the cluster. -A port labelled "dsa" has the following mandatory property: +An uplink/downlink port between switches in the cluster has the following +mandatory property: - link : Should be a list of phandles to other switch's DSA port. This port is used as the outgoing port @@ -48,12 +44,17 @@ A port labelled "dsa" has the following mandatory property: information must be given, not just the one hop routes to neighbouring switches. -A port labelled "cpu" has the following mandatory property: +A CPU port has the following mandatory property: - ethernet : Should be a phandle to a valid Ethernet device node. This host device is what the switch port is connected to. +A user port has the following optional property: + +- label : Describes the label associated with this port, which + will become the netdev name. + Port child nodes may also contain the following optional standardised properties, described in binding documents: @@ -107,7 +108,6 @@ linked into one DSA cluster. switch0port5: port@5 { reg = <5>; - label = "dsa"; phy-mode = "rgmii-txid"; link = <&switch1port6 &switch2port9>; @@ -119,7 +119,6 @@ linked into one DSA cluster. port@6 { reg = <6>; - label = "cpu"; ethernet = <&fec1>; fixed-link { speed = <100>; @@ -165,7 +164,6 @@ linked into one DSA cluster. switch1port5: port@5 { reg = <5>; - label = "dsa"; link = <&switch2port9>; phy-mode = "rgmii-txid"; fixed-link { @@ -176,7 +174,6 @@ linked into one DSA cluster. switch1port6: port@6 { reg = <6>; - label = "dsa"; phy-mode = "rgmii-txid"; link = <&switch0port5>; fixed-link { @@ -255,7 +252,6 @@ linked into one DSA cluster. switch2port9: port@9 { reg = <9>; - label = "dsa"; phy-mode = "rgmii-txid"; link = <&switch1port5 &switch0port5>; diff --git a/Documentation/devicetree/bindings/net/dsa/marvell.txt b/Documentation/devicetree/bindings/net/dsa/marvell.txt index 7629189398aa..7ef9dbb08957 100644 --- a/Documentation/devicetree/bindings/net/dsa/marvell.txt +++ b/Documentation/devicetree/bindings/net/dsa/marvell.txt @@ -14,22 +14,79 @@ The properties described here are those specific to Marvell devices. Additional required and optional properties can be found in dsa.txt. Required properties: -- compatible : Should be one of "marvell,mv88e6085", -- reg : Address on the MII bus for the switch. +- compatible : Should be one of "marvell,mv88e6085" or + "marvell,mv88e6190" +- reg : Address on the MII bus for the switch. Optional properties: - reset-gpios : Should be a gpio specifier for a reset line +- interrupt-parent : Parent interrupt controller +- interrupts : Interrupt from the switch +- interrupt-controller : Indicates the switch is itself an interrupt + controller. This is used for the PHY interrupts. +#interrupt-cells = <2> : Controller uses two cells, number and flag +- mdio : Container of PHY and devices on the switches MDIO + bus. +- mdio? : Container of PHYs and devices on the external MDIO + bus. The node must contains a compatible string of + "marvell,mv88e6xxx-mdio-external" Example: - mdio { - #address-cells = <1>; - #size-cells = <0>; + mdio { + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = <&gpio0>; + interrupts = <27 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; - switch0: switch@0 { - compatible = "marvell,mv88e6085"; - reg = <0>; - reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; - }; - }; + switch0: switch@0 { + compatible = "marvell,mv88e6085"; + reg = <0>; + reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; + }; + mdio { + #address-cells = <1>; + #size-cells = <0>; + switch1phy0: switch1phy0@0 { + reg = <0>; + interrupt-parent = <&switch0>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = <&gpio0>; + interrupts = <27 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + + switch0: switch@0 { + compatible = "marvell,mv88e6390"; + reg = <0>; + reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; + }; + mdio { + #address-cells = <1>; + #size-cells = <0>; + switch1phy0: switch1phy0@0 { + reg = <0>; + interrupt-parent = <&switch0>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + mdio1 { + compatible = "marvell,mv88e6xxx-mdio-external"; + #address-cells = <1>; + #size-cells = <0>; + switch1phy9: switch1phy0@9 { + reg = <9>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/ethernet.txt b/Documentation/devicetree/bindings/net/ethernet.txt index 05150957ecfd..3a6916909d90 100644 --- a/Documentation/devicetree/bindings/net/ethernet.txt +++ b/Documentation/devicetree/bindings/net/ethernet.txt @@ -29,6 +29,9 @@ The following properties are common to the Ethernet controllers: * "smii" * "xgmii" * "trgmii" + * "2000base-x", + * "2500base-x", + * "rxaui" - phy-connection-type: the same as "phy-mode" property but described in ePAPR; - phy-handle: phandle, specifies a reference to a node representing a PHY device; this property is described in ePAPR and so preferred; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt b/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt index 75d398bb1fbb..eea73adc678f 100644 --- a/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt +++ b/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt @@ -1,7 +1,15 @@ Hisilicon hix5hd2 gmac controller Required properties: -- compatible: should be "hisilicon,hix5hd2-gmac". +- compatible: should contain one of the following SoC strings: + * "hisilicon,hix5hd2-gmac" + * "hisilicon,hi3798cv200-gmac" + * "hisilicon,hi3516a-gmac" + and one of the following version string: + * "hisilicon,hisi-gmac-v1" + * "hisilicon,hisi-gmac-v2" + The version v1 includes SoCs hix5hd2. + The version v2 includes SoCs hi3798cv200, hi3516a. - reg: specifies base physical address(s) and size of the device registers. The first region is the MAC register base and size. The second region is external interface control register. @@ -12,6 +20,16 @@ Required properties: - phy-handle: see ethernet.txt [1]. - mac-address: see ethernet.txt [1]. - clocks: clock phandle and specifier pair. +- clock-names: contain the clock name "mac_core"(required) and "mac_ifc"(optional). +- resets: should contain the phandle to the MAC core reset signal(optional), + the MAC interface reset signal(optional) + and the PHY reset signal(optional). +- reset-names: contain the reset signal name "mac_core"(optional), + "mac_ifc"(optional) and "phy"(optional). +- hisilicon,phy-reset-delays-us: triplet of delays if PHY reset signal given. + The 1st cell is reset pre-delay in micro seconds. + The 2nd cell is reset pulse in micro seconds. + The 3rd cell is reset post-delay in micro seconds. - PHY subnode: inherits from phy binding [2] @@ -20,15 +38,19 @@ Required properties: Example: gmac0: ethernet@f9840000 { - compatible = "hisilicon,hix5hd2-gmac"; + compatible = "hisilicon,hi3798cv200-gmac", "hisilicon,hisi-gmac-v2"; reg = <0xf9840000 0x1000>,<0xf984300c 0x4>; interrupts = <0 71 4>; #address-cells = <1>; #size-cells = <0>; - phy-mode = "mii"; + phy-mode = "rgmii"; phy-handle = <&phy2>; mac-address = [00 00 00 00 00 00]; - clocks = <&clock HIX5HD2_MAC0_CLK>; + clocks = <&crg HISTB_ETH0_MAC_CLK>, <&crg HISTB_ETH0_MACIF_CLK>; + clock-names = "mac_core", "mac_ifc"; + resets = <&crg 0xcc 8>, <&crg 0xcc 10>, <&crg 0xcc 12>; + reset-names = "mac_core", "mac_ifc", "phy"; + hisilicon,phy-reset-delays-us = <10000 10000 30000>; phy2: ethernet-phy@2 { reg = <2>; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt index d4b7f2e49984..abfbeecbcf39 100644 --- a/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt @@ -45,6 +45,12 @@ Required properties: depends on the hardware user manual. - port-mode-offset: is offset of port mode field for each port in dsaf. Its value depends on the hardware user manual. +- mc-mac-mask: mask of multicast address, determines bit in multicast address + to set: + 1 stands for this bit will be precisely matched, TCAM will check this bit of + MAC address. + 0 stands for this bit will be fuzzy matched, TCAM won't care about this bit + of MAC address. [1] Documentation/devicetree/bindings/net/phy.txt @@ -74,10 +80,12 @@ dsaf0: dsa@c7000000 { reg = 0; phy-handle = <&phy0>; serdes-syscon = <&serdes>; + mc-mac-mask = [ff f0 00 00 00 00]; }; port@1 { reg = 1; serdes-syscon = <&serdes>; + mc-mac-mask = [ff f0 00 00 00 00]; }; }; diff --git a/Documentation/devicetree/bindings/net/marvell,prestera.txt b/Documentation/devicetree/bindings/net/marvell,prestera.txt new file mode 100644 index 000000000000..5fbab29718e8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell,prestera.txt @@ -0,0 +1,50 @@ +Marvell Prestera Switch Chip bindings +------------------------------------- + +Required properties: +- compatible: one of the following + "marvell,prestera-98dx3236", + "marvell,prestera-98dx3336", + "marvell,prestera-98dx4251", +- reg: address and length of the register set for the device. +- interrupts: interrupt for the device + +Optional properties: +- dfx: phandle reference to the "DFX Server" node + +Example: + +switch { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 MBUS_ID(0x03, 0x00) 0 0x100000>; + + packet-processor@0 { + compatible = "marvell,prestera-98dx3236"; + reg = <0 0x4000000>; + interrupts = <33>, <34>, <35>; + dfx = <&dfx>; + }; +}; + +DFX Server bindings +------------------- + +Required properties: +- compatible: must be "marvell,dfx-server" +- reg: address and length of the register set for the device. + +Example: + +dfx-registers { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 MBUS_ID(0x08, 0x00) 0 0x100000>; + + dfx: dfx@0 { + compatible = "marvell,dfx-server"; + reg = <0 0x100000>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt index 73be8970815e..ae4234ca4ee4 100644 --- a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt +++ b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt @@ -1,7 +1,10 @@ -* Marvell Armada 370 / Armada XP Ethernet Controller (NETA) +* Marvell Armada 370 / Armada XP / Armada 3700 Ethernet Controller (NETA) Required properties: -- compatible: "marvell,armada-370-neta" or "marvell,armada-xp-neta". +- compatible: could be one of the following: + "marvell,armada-370-neta" + "marvell,armada-xp-neta" + "marvell,armada-3700-neta" - reg: address and length of the register set for the device. - interrupts: interrupt for the device - phy: See ethernet.txt file in the same directory. diff --git a/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt b/Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt index 6a9a63cb0543..9be1059ff03f 100644 --- a/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt +++ b/Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt @@ -1,16 +1,21 @@ -Marvell 8897/8997 (sd8897/sd8997) bluetooth SDIO devices +Marvell 8897/8997 (sd8897/sd8997) bluetooth devices (SDIO or USB based) ------ +The 8997 devices supports multiple interfaces. When used on SDIO interfaces, +the btmrvl driver is used and when used on USB interface, the btusb driver is +used. Required properties: - compatible : should be one of the following: - * "marvell,sd8897-bt" - * "marvell,sd8997-bt" + * "marvell,sd8897-bt" (for SDIO) + * "marvell,sd8997-bt" (for SDIO) + * "usb1286,204e" (for USB) Optional properties: - marvell,cal-data: Calibration data downloaded to the device during initialization. This is an array of 28 values(u8). + This is only applicable to SDIO devices. - marvell,wakeup-pin: It represents wakeup pin number of the bluetooth chip. firmware will use the pin to wakeup host system (u16). @@ -18,10 +23,15 @@ Optional properties: platform. The value will be configured to firmware. This is needed to work chip's sleep feature as expected (u16). - interrupt-parent: phandle of the parent interrupt controller - - interrupts : interrupt pin number to the cpu. Driver will request an irq based - on this interrupt number. During system suspend, the irq will be - enabled so that the bluetooth chip can wakeup host platform under - certain condition. During system resume, the irq will be disabled + - interrupt-names: Used only for USB based devices (See below) + - interrupts : specifies the interrupt pin number to the cpu. For SDIO, the + driver will use the first interrupt specified in the interrupt + array. For USB based devices, the driver will use the interrupt + named "wakeup" from the interrupt-names and interrupt arrays. + The driver will request an irq based on this interrupt number. + During system suspend, the irq will be enabled so that the + bluetooth chip can wakeup host platform under certain + conditions. During system resume, the irq will be disabled to make sure unnecessary interrupt is not received. Example: @@ -29,7 +39,9 @@ Example: IRQ pin 119 is used as system wakeup source interrupt. wakeup pin 13 and gap 100ms are configured so that firmware can wakeup host using this device side pin and wakeup latency. -calibration data is also available in below example. + +Example for SDIO device follows (calibration data is also available in +below example). &mmc3 { status = "okay"; @@ -54,3 +66,21 @@ calibration data is also available in below example. marvell,wakeup-gap-ms = /bits/ 16 <0x64>; }; }; + +Example for USB device: + +&usb_host1_ohci { + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + + mvl_bt1: bt@1 { + compatible = "usb1286,204e"; + reg = <1>; + interrupt-parent = <&gpio0>; + interrupt-names = "wakeup"; + interrupts = <119 IRQ_TYPE_LEVEL_LOW>; + marvell,wakeup-pin = /bits/ 16 <0x0d>; + marvell,wakeup-gap-ms = /bits/ 16 <0x64>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt index aa4f4230bfd7..4754364df4c6 100644 --- a/Documentation/devicetree/bindings/net/marvell-pp2.txt +++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt @@ -27,9 +27,7 @@ Optional properties (port): - marvell,loopback: port is loopback mode - phy: a phandle to a phy node defining the PHY address (as the reg - property, a single integer). Note: if this property isn't present, - then fixed link is assumed, and the 'fixed-link' property is - mandatory. + property, a single integer). Example: diff --git a/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt index 8516929c7251..065e8bdb957d 100644 --- a/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt +++ b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt @@ -3,7 +3,7 @@ Properties for an MDIO bus multiplexer controlled by a memory-mapped device This is a special case of a MDIO bus multiplexer. A memory-mapped device, like an FPGA, is used to control which child bus is connected. The mdio-mux node must be a child of the memory-mapped device. The driver currently only -supports devices with eight-bit registers. +supports devices with 8, 16 or 32-bit registers. Required properties in addition to the generic multiplexer properties: @@ -11,7 +11,7 @@ Required properties in addition to the generic multiplexer properties: - reg : integer, contains the offset of the register that controls the bus multiplexer. The size field in the 'reg' property is the size of - register, and must therefore be 1. + register, and must therefore be 1, 2, or 4. - mux-mask : integer, contains an eight-bit mask that specifies which bits in the register control the actual bus multiplexer. The diff --git a/Documentation/devicetree/bindings/net/mediatek-net.txt b/Documentation/devicetree/bindings/net/mediatek-net.txt index c010fafc66a8..c7194e87d5f4 100644 --- a/Documentation/devicetree/bindings/net/mediatek-net.txt +++ b/Documentation/devicetree/bindings/net/mediatek-net.txt @@ -7,7 +7,7 @@ have dual GMAC each represented by a child node.. * Ethernet controller node Required properties: -- compatible: Should be "mediatek,mt7623-eth" +- compatible: Should be "mediatek,mt2701-eth" - reg: Address and length of the register set for the device - interrupts: Should contain the three frame engines interrupts in numeric order. These are fe_int0, fe_int1 and fe_int2. diff --git a/Documentation/devicetree/bindings/net/meson-dwmac.txt b/Documentation/devicetree/bindings/net/meson-dwmac.txt index 89e62ddc69ca..0703ad3f3c1e 100644 --- a/Documentation/devicetree/bindings/net/meson-dwmac.txt +++ b/Documentation/devicetree/bindings/net/meson-dwmac.txt @@ -25,6 +25,22 @@ Required properties on Meson8b and newer: - "clkin0" - first parent clock of the internal mux - "clkin1" - second parent clock of the internal mux +Optional properties on Meson8b and newer: +- amlogic,tx-delay-ns: The internal RGMII TX clock delay (provided + by this driver) in nanoseconds. Allowed values + are: 0ns, 2ns, 4ns, 6ns. + When phy-mode is set to "rgmii" then the TX + delay should be explicitly configured. When + not configured a fallback of 2ns is used. + When the phy-mode is set to either "rgmii-id" + or "rgmii-txid" the TX clock delay is already + provided by the PHY. In that case this + property should be set to 0ns (which disables + the TX clock delay in the MAC to prevent the + clock from going off because both PHY and MAC + are adding a delay). + Any configuration is ignored when the phy-mode + is set to "rmii". Example for Meson6: diff --git a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt index 99c7eb0a00c8..0eedabe22cc3 100644 --- a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt +++ b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt @@ -6,22 +6,35 @@ Required properties: Documentation/devicetree/bindings/net/phy.txt Optional properties: -- vsc8531,vddmac : The vddmac in mV. +- vsc8531,vddmac : The vddmac in mV. Allowed values is listed + in the first row of Table 1 (below). + This property is only used in combination + with the 'edge-slowdown' property. + Default value is 3300. - vsc8531,edge-slowdown : % the edge should be slowed down relative to - the fastest possible edge time. Native sign - need not enter. + the fastest possible edge time. Edge rate sets the drive strength of the MAC - interface output signals. Changing the drive - strength will affect the edge rate of the output - signal. The goal of this setting is to help - reduce electrical emission (EMI) by being able - to reprogram drive strength and in effect slow - down the edge rate if desired. Table 1 shows the - impact to the edge rate per VDDMAC supply for each - drive strength setting. - Ref: Table:1 - Edge rate change below. - -Note: see dt-bindings/net/mscc-phy-vsc8531.h for applicable values + interface output signals. Changing the + drive strength will affect the edge rate of + the output signal. The goal of this setting + is to help reduce electrical emission (EMI) + by being able to reprogram drive strength + and in effect slow down the edge rate if + desired. + To adjust the edge-slowdown, the 'vddmac' + must be specified. Table 1 lists the + supported edge-slowdown values for a given + 'vddmac'. + Default value is 0%. + Ref: Table:1 - Edge rate change (below). +- vsc8531,led-0-mode : LED mode. Specify how the LED[0] should behave. + Allowed values are define in + "include/dt-bindings/net/mscc-phy-vsc8531.h". + Default value is VSC8531_LINK_1000_ACTIVITY (1). +- vsc8531,led-1-mode : LED mode. Specify how the LED[1] should behave. + Allowed values are define in + "include/dt-bindings/net/mscc-phy-vsc8531.h". + Default value is VSC8531_LINK_100_ACTIVITY (2). Table: 1 - Edge rate change ----------------------------------------------------------------| @@ -29,23 +42,23 @@ Table: 1 - Edge rate change | | | 3300 mV 2500 mV 1800 mV 1500 mV | |---------------------------------------------------------------| -| Default Deafult Default Default | +| 0% 0% 0% 0% | | (Fastest) (recommended) (recommended) | |---------------------------------------------------------------| -| -2% -3% -5% -6% | +| 2% 3% 5% 6% | |---------------------------------------------------------------| -| -4% -6% -9% -14% | +| 4% 6% 9% 14% | |---------------------------------------------------------------| -| -7% -10% -16% -21% | +| 7% 10% 16% 21% | |(recommended) (recommended) | |---------------------------------------------------------------| -| -10% -14% -23% -29% | +| 10% 14% 23% 29% | |---------------------------------------------------------------| -| -17% -23% -35% -42% | +| 17% 23% 35% 42% | |---------------------------------------------------------------| -| -29% -37% -52% -58% | +| 29% 37% 52% 58% | |---------------------------------------------------------------| -| -53% -63% -76% -77% | +| 53% 63% 76% 77% | | (slowest) | |---------------------------------------------------------------| @@ -54,5 +67,7 @@ Example: vsc8531_0: ethernet-phy@0 { compatible = "ethernet-phy-id0007.0570"; vsc8531,vddmac = <3300>; - vsc8531,edge-slowdown = <21>; + vsc8531,edge-slowdown = <7>; + vsc8531,led-0-mode = <LINK_1000_ACTIVITY>; + vsc8531,led-1-mode = <LINK_100_ACTIVITY>; }; diff --git a/Documentation/devicetree/bindings/net/oxnas-dwmac.txt b/Documentation/devicetree/bindings/net/oxnas-dwmac.txt new file mode 100644 index 000000000000..df0534e2eda1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/oxnas-dwmac.txt @@ -0,0 +1,39 @@ +* Oxford Semiconductor OXNAS DWMAC Ethernet controller + +The device inherits all the properties of the dwmac/stmmac devices +described in the file stmmac.txt in the current directory with the +following changes. + +Required properties on all platforms: + +- compatible: For the OX820 SoC, it should be : + - "oxsemi,ox820-dwmac" to select glue + - "snps,dwmac-3.512" to select IP version. + +- clocks: Should contain phandles to the following clocks +- clock-names: Should contain the following: + - "stmmaceth" for the host clock - see stmmac.txt + - "gmac" for the peripheral gate clock + +- oxsemi,sys-ctrl: a phandle to the system controller syscon node + +Example : + +etha: ethernet@40400000 { + compatible = "oxsemi,ox820-dwmac", "snps,dwmac-3.512"; + reg = <0x40400000 0x2000>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq", "eth_wake_irq"; + mac-address = [000000000000]; /* Filled in by U-Boot */ + phy-mode = "rgmii"; + + clocks = <&stdclk CLK_820_ETHA>, <&gmacclk>; + clock-names = "gmac", "stmmaceth"; + resets = <&reset RESET_MAC>; + + /* Regmap for sys registers */ + oxsemi,sys-ctrl = <&sys>; + + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt index bc1c3c8bf8fa..b55857696fc3 100644 --- a/Documentation/devicetree/bindings/net/phy.txt +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -19,8 +19,9 @@ Optional Properties: specifications. If neither of these are specified, the default is to assume clause 22. - If the phy's identifier is known then the list may contain an entry - of the form: "ethernet-phy-idAAAA.BBBB" where + If the PHY reports an incorrect ID (or none at all) then the + "compatible" list may contain an entry with the correct PHY ID in the + form: "ethernet-phy-idAAAA.BBBB" where AAAA - The value of the 16 bit Phy Identifier 1 register as 4 hex digits. This is the chip vendor OUI bits 3:18 BBBB - The value of the 16 bit Phy Identifier 2 register as @@ -35,6 +36,22 @@ Optional Properties: - broken-turn-around: If set, indicates the PHY device does not correctly release the turn around line low at the end of a MDIO transaction. +- enet-phy-lane-swap: If set, indicates the PHY will swap the TX/RX lanes to + compensate for the board being designed with the lanes swapped. + +- enet-phy-lane-no-swap: If set, indicates that PHY will disable swap of the + TX/RX lanes. This property allows the PHY to work correcly after e.g. wrong + bootstrap configuration caused by issues in PCB layout design. + +- eee-broken-100tx: +- eee-broken-1000t: +- eee-broken-10gt: +- eee-broken-1000kx: +- eee-broken-10gkx4: +- eee-broken-10gkr: + Mark the corresponding energy efficient ethernet mode as broken and + request the ethernet to stop advertising it. + Example: ethernet-phy@0 { diff --git a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt index 95383c5131fc..8f427550720a 100644 --- a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt +++ b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt @@ -6,6 +6,7 @@ Required properties: - compatible: should be "rockchip,<name>-gamc" "rockchip,rk3228-gmac": found on RK322x SoCs "rockchip,rk3288-gmac": found on RK3288 SoCs + "rockchip,rk3328-gmac": found on RK3328 SoCs "rockchip,rk3366-gmac": found on RK3366 SoCs "rockchip,rk3368-gmac": found on RK3368 SoCs "rockchip,rk3399-gmac": found on RK3399 SoCs diff --git a/Documentation/devicetree/bindings/net/smsc-lan91c111.txt b/Documentation/devicetree/bindings/net/smsc-lan91c111.txt index e77e167593db..309e37eb7c7c 100644 --- a/Documentation/devicetree/bindings/net/smsc-lan91c111.txt +++ b/Documentation/devicetree/bindings/net/smsc-lan91c111.txt @@ -13,3 +13,5 @@ Optional properties: 16-bit access only. - power-gpios: GPIO to control the PWRDWN pin - reset-gpios: GPIO to control the RESET pin +- pxa-u16-align4 : Boolean, put in place the workaround the force all + u16 writes to be 32 bits aligned diff --git a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt index d93f71ce8346..21d27aa4c68c 100644 --- a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt +++ b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt @@ -1,5 +1,8 @@ * Synopsys DWC Ethernet QoS IP version 4.10 driver (GMAC) +This binding is deprecated, but it continues to be supported, but new +features should be preferably added to the stmmac binding document. + This binding supports the Synopsys Designware Ethernet QoS (Quality Of Service) IP block. The IP supports multiple options for bus type, clocking and reset structure, and feature list. Consequently, a number of properties and list diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index 41b49e6075f5..d3bfc2b30fb5 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -1,7 +1,7 @@ * STMicroelectronics 10/100/1000 Ethernet driver (GMAC) Required properties: -- compatible: Should be "snps,dwmac-<ip_version>" "snps,dwmac" +- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac" For backwards compatibility: "st,spear600-gmac" is also supported. - reg: Address and length of the register set for the device - interrupt-parent: Should be the phandle for the interrupt controller @@ -34,7 +34,13 @@ Optional properties: platforms. - tx-fifo-depth: See ethernet.txt file in the same directory - rx-fifo-depth: See ethernet.txt file in the same directory -- snps,pbl Programmable Burst Length +- snps,pbl Programmable Burst Length (tx and rx) +- snps,txpbl Tx Programmable Burst Length. Only for GMAC and newer. + If set, DMA tx will use this value rather than snps,pbl. +- snps,rxpbl Rx Programmable Burst Length. Only for GMAC and newer. + If set, DMA rx will use this value rather than snps,pbl. +- snps,no-pbl-x8 Don't multiply the pbl/txpbl/rxpbl values by 8. + For core rev < 3.50, don't multiply the values by 4. - snps,aal Address-Aligned Beats - snps,fixed-burst Program the DMA to use the fixed burst mode - snps,mixed-burst Program the DMA to use the mixed burst mode @@ -43,6 +49,8 @@ Optional properties: - snps,force_sf_dma_mode Force DMA to use the Store and Forward mode for both tx and rx. This flag is ignored if force_thresh_dma_mode is set. +- snps,en-tx-lpi-clockgating Enable gating of the MAC TX clock during + TX low-power mode - snps,multicast-filter-bins: Number of multicast filter hash bins supported by this device instance - snps,perfect-filter-entries: Number of perfect filter entries supported @@ -50,6 +58,8 @@ Optional properties: - snps,ps-speed: port selection speed that can be passed to the core when PCS is supported. For example, this is used in case of SGMII and MAC2MAC connection. +- snps,tso: this enables the TSO feature otherwise it will be managed by + MAC HW capability register. Only for GMAC4 and newer. - AXI BUS Mode parameters: below the list of all the parameters to program the AXI register inside the DMA module: - snps,lpi_en: enable Low Power Interface @@ -57,13 +67,10 @@ Optional properties: - snps,wr_osr_lmt: max write outstanding req. limit - snps,rd_osr_lmt: max read outstanding req. limit - snps,kbbe: do not cross 1KiB boundary. - - snps,axi_all: align address - snps,blen: this is a vector of supported burst length. - snps,fb: fixed-burst - snps,mb: mixed-burst - snps,rb: rebuild INCRx Burst - - snps,tso: this enables the TSO feature otherwise it will be managed by - MAC HW capability register. - mdio: with compatible = "snps,dwmac-mdio", create and register mdio bus. Examples: diff --git a/Documentation/devicetree/bindings/net/ti,dp83867.txt b/Documentation/devicetree/bindings/net/ti,dp83867.txt index 5d21141a68b5..afe9630a5e7d 100644 --- a/Documentation/devicetree/bindings/net/ti,dp83867.txt +++ b/Documentation/devicetree/bindings/net/ti,dp83867.txt @@ -3,12 +3,26 @@ Required properties: - reg - The ID number for the phy, usually a small integer - ti,rx-internal-delay - RGMII Receive Clock Delay - see dt-bindings/net/ti-dp83867.h - for applicable values + for applicable values. Required only if interface type is + PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_RXID - ti,tx-internal-delay - RGMII Transmit Clock Delay - see dt-bindings/net/ti-dp83867.h - for applicable values + for applicable values. Required only if interface type is + PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_TXID - ti,fifo-depth - Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h for applicable values +Optional property: + - ti,min-output-impedance - MAC Interface Impedance control to set + the programmable output impedance to + minimum value (35 ohms). + - ti,max-output-impedance - MAC Interface Impedance control to set + the programmable output impedance to + maximum value (70 ohms). + +Note: ti,min-output-impedance and ti,max-output-impedance are mutually + exclusive. When both properties are present ti,max-output-impedance + takes precedence. + Default child nodes are standard Ethernet PHY device nodes as described in Documentation/devicetree/bindings/net/phy.txt diff --git a/Documentation/devicetree/bindings/net/wireless/ieee80211.txt b/Documentation/devicetree/bindings/net/wireless/ieee80211.txt new file mode 100644 index 000000000000..f6442b1397f5 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/ieee80211.txt @@ -0,0 +1,24 @@ +Common IEEE 802.11 properties + +This provides documentation of common properties that are valid for all wireless +devices. + +Optional properties: + - ieee80211-freq-limit : list of supported frequency ranges in KHz. This can be + used for devices that in a given config support less channels than + normally. It may happen chipset supports a wide wireless band but it is + limited to some part of it due to used antennas or power amplifier. + An example case for this can be tri-band wireless router with two + identical chipsets used for two different 5 GHz subbands. Using them + incorrectly could not work or decrease performance noticeably. + +Example: + +pcie@0,0 { + reg = <0x0000 0 0 0 0>; + wifi@0,0 { + reg = <0x0000 0 0 0 0>; + ieee80211-freq-limit = <2402000 2482000>, + <5170000 5250000>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt b/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt index c421aba0a5bc..0854451ff91d 100644 --- a/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt +++ b/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt @@ -1,15 +1,18 @@ -Marvell 8897/8997 (sd8897/sd8997) SDIO devices +Marvell 8787/8897/8997 (sd8787/sd8897/sd8997/pcie8997) SDIO/PCIE devices ------ -This node provides properties for controlling the marvell sdio wireless device. -The node is expected to be specified as a child node to the SDIO controller that +This node provides properties for controlling the Marvell SDIO/PCIE wireless device. +The node is expected to be specified as a child node to the SDIO/PCIE controller that connects the device to the system. Required properties: - compatible : should be one of the following: + * "marvell,sd8787" * "marvell,sd8897" * "marvell,sd8997" + * "pci11ab,2b42" + * "pci1b4b,2b42" Optional properties: @@ -32,6 +35,9 @@ Optional properties: so that the wifi chip can wakeup host platform under certain condition. during system resume, the irq will be disabled to make sure unnecessary interrupt is not received. + - vmmc-supply: a phandle of a regulator, supplying VCC to the card + - mmc-pwrseq: phandle to the MMC power sequence node. See "mmc-pwrseq-*" + for documentation of MMC power sequence bindings. Example: @@ -44,6 +50,7 @@ so that firmware can wakeup host using this device side pin. &mmc3 { status = "okay"; vmmc-supply = <&wlan_en_reg>; + mmc-pwrseq = <&wifi_pwrseq>; bus-width = <4>; cap-power-off-card; keep-power-in-suspend; diff --git a/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt b/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt new file mode 100644 index 000000000000..b7396c8c271c --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt @@ -0,0 +1,48 @@ +* Qualcomm Atheros ath9k wireless devices + +This node provides properties for configuring the ath9k wireless device. The +node is expected to be specified as a child node of the PCI controller to +which the wireless chip is connected. + +Required properties: +- compatible: For PCI and PCIe devices this should be an identifier following + the format as defined in "PCI Bus Binding to Open Firmware" + Revision 2.1. One of the possible formats is "pciVVVV,DDDD" + where VVVV is the PCI vendor ID and DDDD is PCI device ID. + Typically QCA's PCI vendor ID 168c is used while the PCI device + ID depends on the chipset - see the following (possibly + incomplete) list: + - 0023 for AR5416 + - 0024 for AR5418 + - 0027 for AR9160 + - 0029 for AR9220 and AR9223 + - 002a for AR9280 and AR9283 + - 002b for AR9285 + - 002c for AR2427 + - 002d for AR9227 + - 002e for AR9287 + - 0030 for AR9380, AR9381 and AR9382 + - 0032 for AR9485 + - 0033 for AR9580 and AR9590 + - 0034 for AR9462 + - 0036 for AR9565 + - 0037 for AR9485 +- reg: Address and length of the register set for the device. + +Optional properties: +- qca,no-eeprom: Indicates that there is no physical EEPROM connected to the + ath9k wireless chip (in this case the calibration / + EEPROM data will be loaded from userspace using the + kernel firmware loader). +- mac-address: See ethernet.txt in the parent directory +- local-mac-address: See ethernet.txt in the parent directory + + +In this example, the node is defined as child node of the PCI controller: +&pci0 { + wifi@168c,002d { + compatible = "pci168c,002d"; + reg = <0x7000 0 0 0 0x1000>; + qca,no-eeprom; + }; +}; diff --git a/Documentation/devicetree/bindings/nvmem/brcm,ocotp.txt b/Documentation/devicetree/bindings/nvmem/brcm,ocotp.txt new file mode 100644 index 000000000000..6462e12d8de6 --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/brcm,ocotp.txt @@ -0,0 +1,17 @@ +Broadcom OTP memory controller + +Required Properties: +- compatible: "brcm,ocotp" for the first generation Broadcom OTPC which is used + in Cygnus and supports 32 bit read/write. Use "brcm,ocotp-v2" for the second + generation Broadcom OTPC which is used in SoC's such as Stingray and supports + 64-bit read/write. +- reg: Base address of the OTP controller. +- brcm,ocotp-size: Amount of memory available, in 32 bit words + +Example: + +otp: otp@0301c800 { + compatible = "brcm,ocotp"; + reg = <0x0301c800 0x2c>; + brcm,ocotp-size = <2048>; +}; diff --git a/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt b/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt index 383d5889e95a..966a72ecc6bd 100644 --- a/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt +++ b/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt @@ -1,13 +1,15 @@ Freescale i.MX6 On-Chip OTP Controller (OCOTP) device tree bindings This binding represents the on-chip eFuse OTP controller found on -i.MX6Q/D, i.MX6DL/S, i.MX6SL, and i.MX6SX SoCs. +i.MX6Q/D, i.MX6DL/S, i.MX6SL, i.MX6SX and i.MX6UL SoCs. Required properties: - compatible: should be one of "fsl,imx6q-ocotp" (i.MX6Q/D/DL/S), "fsl,imx6sl-ocotp" (i.MX6SL), or - "fsl,imx6sx-ocotp" (i.MX6SX), followed by "syscon". + "fsl,imx6sx-ocotp" (i.MX6SX), + "fsl,imx6ul-ocotp" (i.MX6UL), + followed by "syscon". - reg: Should contain the register base and length. - clocks: Should contain a phandle pointing to the gated peripheral clock. diff --git a/Documentation/devicetree/bindings/nvmem/lpc1850-otp.txt b/Documentation/devicetree/bindings/nvmem/lpc1850-otp.txt new file mode 100644 index 000000000000..853b6a754644 --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/lpc1850-otp.txt @@ -0,0 +1,20 @@ +* NXP LPC18xx OTP memory + +Internal OTP (One Time Programmable) memory for NXP LPC18xx/43xx devices. + +Required properties: + - compatible: Should be "nxp,lpc1850-otp" + - reg: Must contain an entry with the physical base address and length + for each entry in reg-names. + - address-cells: must be set to 1. + - size-cells: must be set to 1. + +See nvmem.txt for more information. + +Example: + otp: otp@40045000 { + compatible = "nxp,lpc1850-otp"; + reg = <0x40045000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/opp/opp.txt b/Documentation/devicetree/bindings/opp/opp.txt index ee91cbdd95ee..63725498bd20 100644 --- a/Documentation/devicetree/bindings/opp/opp.txt +++ b/Documentation/devicetree/bindings/opp/opp.txt @@ -86,8 +86,14 @@ Optional properties: Single entry is for target voltage and three entries are for <target min max> voltages. - Entries for multiple regulators must be present in the same order as - regulators are specified in device's DT node. + Entries for multiple regulators shall be provided in the same field separated + by angular brackets <>. The OPP binding doesn't provide any provisions to + relate the values to their power supplies or the order in which the supplies + need to be configured and that is left for the implementation specific + binding. + + Entries for all regulators shall be of the same size, i.e. either all use a + single value or triplets. - opp-microvolt-<name>: Named opp-microvolt property. This is exactly similar to the above opp-microvolt property, but allows multiple voltage ranges to be @@ -104,10 +110,13 @@ Optional properties: Should only be set if opp-microvolt is set for the OPP. - Entries for multiple regulators must be present in the same order as - regulators are specified in device's DT node. If this property isn't required - for few regulators, then this should be marked as zero for them. If it isn't - required for any regulator, then this property need not be present. + Entries for multiple regulators shall be provided in the same field separated + by angular brackets <>. If current values aren't required for a regulator, + then it shall be filled with 0. If current values aren't required for any of + the regulators, then this field is not required. The OPP binding doesn't + provide any provisions to relate the values to their power supplies or the + order in which the supplies need to be configured and that is left for the + implementation specific binding. - opp-microamp-<name>: Named opp-microamp property. Similar to opp-microvolt-<name> property, but for microamp instead. @@ -127,7 +136,7 @@ Optional properties: larger OPP table, based on what version of the hardware we are running on. We still can't have multiple nodes with the same opp-hz value in OPP table. - It's an user defined array containing a hierarchy of hardware version numbers, + It's a user defined array containing a hierarchy of hardware version numbers, supported by the OPP. For example: a platform with hierarchy of three levels of versions (A, B and C), this field should be like <X Y Z>, where X corresponds to Version hierarchy A, Y corresponds to version hierarchy B and Z @@ -179,14 +188,14 @@ Example 1: Single cluster Dual-core ARM cortex A9, switch DVFS states together. opp@1000000000 { opp-hz = /bits/ 64 <1000000000>; - opp-microvolt = <970000 975000 985000>; + opp-microvolt = <975000 970000 985000>; opp-microamp = <70000>; clock-latency-ns = <300000>; opp-suspend; }; opp@1100000000 { opp-hz = /bits/ 64 <1100000000>; - opp-microvolt = <980000 1000000 1010000>; + opp-microvolt = <1000000 980000 1010000>; opp-microamp = <80000>; clock-latency-ns = <310000>; }; @@ -258,14 +267,14 @@ independently. opp@1000000000 { opp-hz = /bits/ 64 <1000000000>; - opp-microvolt = <970000 975000 985000>; + opp-microvolt = <975000 970000 985000>; opp-microamp = <70000>; clock-latency-ns = <300000>; opp-suspend; }; opp@1100000000 { opp-hz = /bits/ 64 <1100000000>; - opp-microvolt = <980000 1000000 1010000>; + opp-microvolt = <1000000 980000 1010000>; opp-microamp = <80000>; clock-latency-ns = <310000>; }; @@ -334,14 +343,14 @@ DVFS state together. opp@1000000000 { opp-hz = /bits/ 64 <1000000000>; - opp-microvolt = <970000 975000 985000>; + opp-microvolt = <975000 970000 985000>; opp-microamp = <70000>; clock-latency-ns = <300000>; opp-suspend; }; opp@1100000000 { opp-hz = /bits/ 64 <1100000000>; - opp-microvolt = <980000 1000000 1010000>; + opp-microvolt = <1000000 980000 1010000>; opp-microamp = <80000>; clock-latency-ns = <310000>; }; @@ -360,7 +369,7 @@ DVFS state together. opp@1300000000 { opp-hz = /bits/ 64 <1300000000>; - opp-microvolt = <1045000 1050000 1055000>; + opp-microvolt = <1050000 1045000 1055000>; opp-microamp = <95000>; clock-latency-ns = <400000>; opp-suspend; @@ -373,7 +382,7 @@ DVFS state together. }; opp@1500000000 { opp-hz = /bits/ 64 <1500000000>; - opp-microvolt = <1010000 1100000 1110000>; + opp-microvolt = <1100000 1010000 1110000>; opp-microamp = <95000>; clock-latency-ns = <400000>; turbo-mode; @@ -386,10 +395,12 @@ Example 4: Handling multiple regulators / { cpus { cpu@0 { - compatible = "arm,cortex-a7"; + compatible = "vendor,cpu-type"; ... - cpu-supply = <&cpu_supply0>, <&cpu_supply1>, <&cpu_supply2>; + vcc0-supply = <&cpu_supply0>; + vcc1-supply = <&cpu_supply1>; + vcc2-supply = <&cpu_supply2>; operating-points-v2 = <&cpu0_opp_table>; }; }; @@ -413,9 +424,9 @@ Example 4: Handling multiple regulators opp@1000000000 { opp-hz = /bits/ 64 <1000000000>; - opp-microvolt = <970000 975000 985000>, /* Supply 0 */ - <960000 965000 975000>, /* Supply 1 */ - <960000 965000 975000>; /* Supply 2 */ + opp-microvolt = <975000 970000 985000>, /* Supply 0 */ + <965000 960000 975000>, /* Supply 1 */ + <965000 960000 975000>; /* Supply 2 */ opp-microamp = <70000>, /* Supply 0 */ <70000>, /* Supply 1 */ <70000>; /* Supply 2 */ @@ -426,9 +437,9 @@ Example 4: Handling multiple regulators opp@1000000000 { opp-hz = /bits/ 64 <1000000000>; - opp-microvolt = <970000 975000 985000>, /* Supply 0 */ - <960000 965000 975000>, /* Supply 1 */ - <960000 965000 975000>; /* Supply 2 */ + opp-microvolt = <975000 970000 985000>, /* Supply 0 */ + <965000 960000 975000>, /* Supply 1 */ + <965000 960000 975000>; /* Supply 2 */ opp-microamp = <70000>, /* Supply 0 */ <0>, /* Supply 1 doesn't need this */ <70000>; /* Supply 2 */ @@ -463,7 +474,7 @@ Example 5: opp-supported-hw */ opp-supported-hw = <0xF 0xFFFFFFFF 0xFFFFFFFF> opp-hz = /bits/ 64 <600000000>; - opp-microvolt = <900000 915000 925000>; + opp-microvolt = <915000 900000 925000>; ... }; @@ -476,7 +487,7 @@ Example 5: opp-supported-hw */ opp-supported-hw = <0x20 0xff0000ff 0x0000f4f0> opp-hz = /bits/ 64 <800000000>; - opp-microvolt = <900000 915000 925000>; + opp-microvolt = <915000 900000 925000>; ... }; }; @@ -501,18 +512,18 @@ Example 6: opp-microvolt-<name>, opp-microamp-<name>: opp@1000000000 { opp-hz = /bits/ 64 <1000000000>; - opp-microvolt-slow = <900000 915000 925000>; - opp-microvolt-fast = <970000 975000 985000>; + opp-microvolt-slow = <915000 900000 925000>; + opp-microvolt-fast = <975000 970000 985000>; opp-microamp-slow = <70000>; opp-microamp-fast = <71000>; }; opp@1200000000 { opp-hz = /bits/ 64 <1200000000>; - opp-microvolt-slow = <900000 915000 925000>, /* Supply vcc0 */ - <910000 925000 935000>; /* Supply vcc1 */ - opp-microvolt-fast = <970000 975000 985000>, /* Supply vcc0 */ - <960000 965000 975000>; /* Supply vcc1 */ + opp-microvolt-slow = <915000 900000 925000>, /* Supply vcc0 */ + <925000 910000 935000>; /* Supply vcc1 */ + opp-microvolt-fast = <975000 970000 985000>, /* Supply vcc0 */ + <965000 960000 975000>; /* Supply vcc1 */ opp-microamp = <70000>; /* Will be used for both slow/fast */ }; }; diff --git a/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt b/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt index 01b88f4e0d5b..b8e48b4762b2 100644 --- a/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt +++ b/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt @@ -1,10 +1,17 @@ * Broadcom iProc PCIe controller with the platform bus interface Required properties: -- compatible: Must be "brcm,iproc-pcie" for PAXB, or "brcm,iproc-pcie-paxc" - for PAXC. PAXB-based root complex is used for external endpoint devices. - PAXC-based root complex is connected to emulated endpoint devices - internal to the ASIC +- compatible: + "brcm,iproc-pcie" for the first generation of PAXB based controller, +used in SoCs including NSP, Cygnus, NS2, and Pegasus + "brcm,iproc-pcie-paxb-v2" for the second generation of PAXB-based +controllers, used in Stingray + "brcm,iproc-pcie-paxc" for the first generation of PAXC based +controller, used in NS2 + "brcm,iproc-pcie-paxc-v2" for the second generation of PAXC based +controller, used in Stingray + PAXB-based root complex is used for external endpoint devices. PAXC-based +root complex is connected to emulated endpoint devices internal to the ASIC - reg: base address and length of the PCIe controller I/O register space - #interrupt-cells: set to <1> - interrupt-map-mask and interrupt-map, standard PCI properties to define the @@ -19,6 +26,10 @@ Required properties: Optional properties: - phys: phandle of the PCIe PHY device - phy-names: must be "pcie-phy" +- dma-coherent: present if DMA operations are coherent +- dma-ranges: Some PAXB-based root complexes do not have inbound mapping done + by the ASIC after power on reset. In this case, SW is required to configure +the mapping, based on inbound memory regions specified by this property. - brcm,pcie-ob: Some iProc SoCs do not have the outbound address mapping done by the ASIC after power on reset. In this case, SW needs to configure it @@ -29,11 +40,6 @@ effective: Required: - brcm,pcie-ob-axi-offset: The offset from the AXI address to the internal address used by the iProc PCIe core (not the PCIe address) -- brcm,pcie-ob-window-size: The outbound address mapping window size (in MB) - -Optional: -- brcm,pcie-ob-oarr-size: Some iProc SoCs need the OARR size bit to be set to -increase the outbound window size MSI support (optional): @@ -41,10 +47,19 @@ For older platforms without MSI integrated in the GIC, iProc PCIe core provides an event queue based MSI support. The iProc MSI uses host memories to store MSI posted writes in the event queues -- msi-parent: Link to the device node of the MSI controller. On newer iProc -platforms, the MSI controller may be gicv2m or gicv3-its. On older iProc -platforms without MSI support in its interrupt controller, one may use the -event queue based MSI support integrated within the iProc PCIe core. +On newer iProc platforms, gicv2m or gicv3-its based MSI support should be used + +- msi-map: Maps a Requester ID to an MSI controller and associated MSI +sideband data + +- msi-parent: Link to the device node of the MSI controller, used when no MSI +sideband data is passed between the iProc PCIe controller and the MSI +controller + +Refer to the following binding documents for more detailed description on +the use of 'msi-map' and 'msi-parent': + Documentation/devicetree/bindings/pci/pci-msi.txt + Documentation/devicetree/bindings/interrupt-controller/msi.txt When the iProc event queue based MSI is used, one needs to define the following properties in the MSI device node: @@ -80,9 +95,7 @@ Example: phy-names = "pcie-phy"; brcm,pcie-ob; - brcm,pcie-ob-oarr-size; brcm,pcie-ob-axi-offset = <0x00000000>; - brcm,pcie-ob-window-size = <256>; msi-parent = <&msi0>; diff --git a/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt b/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt index 59c2f47aa303..b7fa3b97986d 100644 --- a/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt +++ b/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt @@ -42,3 +42,40 @@ Hip05 Example (note that Hip06 is the same except compatible): 0x0 0 0 4 &mbigen_pcie 4 13>; status = "ok"; }; + +HiSilicon Hip06/Hip07 PCIe host bridge DT (almost-ECAM) description. +The properties and their meanings are identical to those described in +host-generic-pci.txt except as listed below. + +Properties of the host controller node that differ from +host-generic-pci.txt: + +- compatible : Must be "hisilicon,pcie-almost-ecam" + +- reg : Two entries: First the ECAM configuration space for any + other bus underneath the root bus. Second, the base + and size of the HiSilicon host bridge registers include + the RC's own config space. + +Example: + pcie0: pcie@a0090000 { + compatible = "hisilicon,pcie-almost-ecam"; + reg = <0 0xb0000000 0 0x2000000>, /* ECAM configuration space */ + <0 0xa0090000 0 0x10000>; /* host bridge registers */ + bus-range = <0 31>; + msi-map = <0x0000 &its_dsa 0x0000 0x2000>; + msi-map-mask = <0xffff>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + dma-coherent; + ranges = <0x02000000 0 0xb2000000 0x0 0xb2000000 0 0x5ff0000 + 0x01000000 0 0 0 0xb7ff0000 0 0x10000>; + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = <0x0 0 0 1 &mbigen_pcie0 650 4 + 0x0 0 0 2 &mbigen_pcie0 650 4 + 0x0 0 0 3 &mbigen_pcie0 650 4 + 0x0 0 0 4 &mbigen_pcie0 650 4>; + status = "ok"; + }; diff --git a/Documentation/devicetree/bindings/pci/layerscape-pci.txt b/Documentation/devicetree/bindings/pci/layerscape-pci.txt index 41e9f55a1467..ee1c72d5162e 100644 --- a/Documentation/devicetree/bindings/pci/layerscape-pci.txt +++ b/Documentation/devicetree/bindings/pci/layerscape-pci.txt @@ -15,6 +15,7 @@ Required properties: - compatible: should contain the platform identifier such as: "fsl,ls1021a-pcie", "snps,dw-pcie" "fsl,ls2080a-pcie", "fsl,ls2085a-pcie", "snps,dw-pcie" + "fsl,ls1046a-pcie" - reg: base addresses and lengths of the PCIe controller - interrupts: A list of interrupt outputs of the controller. Must contain an entry for each entry in the interrupt-names property. diff --git a/Documentation/devicetree/bindings/pci/mvebu-pci.txt b/Documentation/devicetree/bindings/pci/mvebu-pci.txt index 08c716b2c6b6..2de6f65ecfb1 100644 --- a/Documentation/devicetree/bindings/pci/mvebu-pci.txt +++ b/Documentation/devicetree/bindings/pci/mvebu-pci.txt @@ -78,7 +78,8 @@ and the following optional properties: multiple lanes. If this property is not found, we assume that the value is 0. - reset-gpios: optional gpio to PERST# -- reset-delay-us: delay in us to wait after reset de-assertion +- reset-delay-us: delay in us to wait after reset de-assertion, if not + specified will default to 100ms, as required by the PCIe specification. Example: diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt index b8cc395fffea..982a74ea6df9 100644 --- a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt @@ -110,6 +110,20 @@ Power supplies for Tegra124: - avdd-pll-erefe-supply: Power supply for PLLE (shared with USB3). Must supply 1.05 V. +Power supplies for Tegra210: +- Required: + - avdd-pll-uerefe-supply: Power supply for PLLE (shared with USB3). Must + supply 1.05 V. + - hvddio-pex-supply: High-voltage supply for PCIe I/O and PCIe output + clocks. Must supply 1.8 V. + - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + - dvdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must + supply 1.05 V. + - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3). + Must supply 3.3 V. + - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must + supply 1.8 V. + Root ports are defined as subnodes of the PCIe controller node. Required properties: @@ -436,3 +450,99 @@ Board DTS: status = "okay"; }; }; + +Tegra210: +--------- + +SoC DTSI: + + pcie-controller@01003000 { + compatible = "nvidia,tegra210-pcie"; + device_type = "pci"; + reg = <0x0 0x01003000 0x0 0x00000800 /* PADS registers */ + 0x0 0x01003800 0x0 0x00000800 /* AFI registers */ + 0x0 0x02000000 0x0 0x10000000>; /* configuration space */ + reg-names = "pads", "afi", "cs"; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */ + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + + bus-range = <0x00 0xff>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x82000000 0 0x01000000 0x0 0x01000000 0 0x00001000 /* port 0 configuration space */ + 0x82000000 0 0x01001000 0x0 0x01001000 0 0x00001000 /* port 1 configuration space */ + 0x81000000 0 0x0 0x0 0x12000000 0 0x00010000 /* downstream I/O (64 KiB) */ + 0x82000000 0 0x13000000 0x0 0x13000000 0 0x0d000000 /* non-prefetchable memory (208 MiB) */ + 0xc2000000 0 0x20000000 0x0 0x20000000 0 0x20000000>; /* prefetchable memory (512 MiB) */ + + clocks = <&tegra_car TEGRA210_CLK_PCIE>, + <&tegra_car TEGRA210_CLK_AFI>, + <&tegra_car TEGRA210_CLK_PLL_E>, + <&tegra_car TEGRA210_CLK_CML0>; + clock-names = "pex", "afi", "pll_e", "cml"; + resets = <&tegra_car 70>, + <&tegra_car 72>, + <&tegra_car 74>; + reset-names = "pex", "afi", "pcie_x"; + status = "disabled"; + + pci@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x01000000 0 0x1000>; + reg = <0x000800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <4>; + }; + + pci@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x01001000 0 0x1000>; + reg = <0x001000 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <1>; + }; + }; + +Board DTS: + + pcie-controller@01003000 { + status = "okay"; + + avdd-pll-uerefe-supply = <&avdd_1v05_pll>; + hvddio-pex-supply = <&vdd_1v8>; + dvddio-pex-supply = <&vdd_pex_1v05>; + dvdd-pex-pll-supply = <&vdd_pex_1v05>; + hvdd-pex-pll-e-supply = <&vdd_1v8>; + vddio-pex-ctl-supply = <&vdd_1v8>; + + pci@1,0 { + phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-0}>, + <&{/padctl@7009f000/pads/pcie/lanes/pcie-1}>, + <&{/padctl@7009f000/pads/pcie/lanes/pcie-2}>, + <&{/padctl@7009f000/pads/pcie/lanes/pcie-3}>; + phy-names = "pcie-0", "pcie-1", "pcie-2", "pcie-3"; + status = "okay"; + }; + + pci@2,0 { + phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-4}>; + phy-names = "pcie-0"; + status = "okay"; + }; + }; diff --git a/Documentation/devicetree/bindings/pci/pci-iommu.txt b/Documentation/devicetree/bindings/pci/pci-iommu.txt index 56c829621b9a..0def586fdcdf 100644 --- a/Documentation/devicetree/bindings/pci/pci-iommu.txt +++ b/Documentation/devicetree/bindings/pci/pci-iommu.txt @@ -32,17 +32,17 @@ PCI root complex Optional properties ------------------- -- iommu-map: Maps a Requester ID to an IOMMU and associated iommu-specifier +- iommu-map: Maps a Requester ID to an IOMMU and associated IOMMU specifier data. The property is an arbitrary number of tuples of (rid-base,iommu,iommu-base,length). Any RID r in the interval [rid-base, rid-base + length) is associated with - the listed IOMMU, with the iommu-specifier (r - rid-base + iommu-base). + the listed IOMMU, with the IOMMU specifier (r - rid-base + iommu-base). - iommu-map-mask: A mask to be applied to each Requester ID prior to being - mapped to an iommu-specifier per the iommu-map property. + mapped to an IOMMU specifier per the iommu-map property. Example (1) diff --git a/Documentation/devicetree/bindings/pci/pci.txt b/Documentation/devicetree/bindings/pci/pci.txt index 08dcfad09f8d..50f9e2ca5b13 100644 --- a/Documentation/devicetree/bindings/pci/pci.txt +++ b/Documentation/devicetree/bindings/pci/pci.txt @@ -18,3 +18,9 @@ driver implementation may support the following properties: host bridges in the system, otherwise potentially conflicting domain numbers may be assigned to root buses behind different host bridges. The domain number for each host bridge in the system must be unique. +- max-link-speed: + If present this property specifies PCI gen for link capability. Host + drivers could add this as a strategy to avoid unnecessary operation for + unsupported link speed, for instance, trying to do training for + unsupported link speed, etc. Must be '4' for gen4, '3' for gen3, '2' + for gen2, and '1' for gen1. Any other values are invalid. diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt index 4059a6f89bc1..e15f9b19901f 100644 --- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt @@ -7,6 +7,7 @@ - "qcom,pcie-ipq8064" for ipq8064 - "qcom,pcie-apq8064" for apq8064 - "qcom,pcie-apq8084" for apq8084 + - "qcom,pcie-msm8996" for msm8996 or apq8096 - reg: Usage: required @@ -92,6 +93,17 @@ - "aux" Auxiliary (AUX) clock - "bus_master" Master AXI clock - "bus_slave" Slave AXI clock + +- clock-names: + Usage: required for msm8996/apq8096 + Value type: <stringlist> + Definition: Should contain the following entries + - "pipe" Pipe Clock driving internal logic + - "aux" Auxiliary (AUX) clock + - "cfg" Configuration clock + - "bus_master" Master AXI clock + - "bus_slave" Slave AXI clock + - resets: Usage: required Value type: <prop-encoded-array> @@ -115,7 +127,7 @@ - "core" Core reset - power-domains: - Usage: required for apq8084 + Usage: required for apq8084 and msm8996/apq8096 Value type: <prop-encoded-array> Definition: A phandle and power domain specifier pair to the power domain which is responsible for collapsing diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt index 6cf99690eef9..34712d6fd253 100644 --- a/Documentation/devicetree/bindings/pci/rcar-pci.txt +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -6,7 +6,9 @@ compatible: "renesas,pcie-r8a7779" for the R8A7779 SoC; "renesas,pcie-r8a7791" for the R8A7791 SoC; "renesas,pcie-r8a7793" for the R8A7793 SoC; "renesas,pcie-r8a7795" for the R8A7795 SoC; + "renesas,pcie-r8a7796" for the R8A7796 SoC; "renesas,pcie-rcar-gen2" for a generic R-Car Gen2 compatible device. + "renesas,pcie-rcar-gen3" for a generic R-Car Gen3 compatible device. When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt index 71aeda1ca055..1453a734c2f5 100644 --- a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt +++ b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt @@ -43,6 +43,8 @@ Required properties: - interrupt-map-mask and interrupt-map: standard PCI properties Optional Property: +- aspm-no-l0s: RC won't support ASPM L0s. This property is needed if + using 24MHz OSC for RC's PHY. - ep-gpios: contain the entry for pre-reset gpio - num-lanes: number of lanes to use - vpcie3v3-supply: The phandle to the 3.3v regulator to use for PCIe. diff --git a/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt b/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt index 4f9d23d2ed67..7d3b09474657 100644 --- a/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt +++ b/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt @@ -7,8 +7,19 @@ Required properties: - compatible: "samsung,exynos5440-pcie" - reg: base addresses and lengths of the pcie controller, the phy controller, additional register for the phy controller. + (Registers for the phy controller are DEPRECATED. + Use the PHY framework.) +- reg-names : First name should be set to "elbi". + And use the "config" instead of getting the confgiruation address space + from "ranges". + NOTE: When use the "config" property, reg-names must be set. - interrupts: A list of interrupt outputs for level interrupt, pulse interrupt, special interrupt. +- phys: From PHY binding. Phandle for the Generic PHY. + Refer to Documentation/devicetree/bindings/phy/samsung-phy.txt + +Other common properties refer to + Documentation/devicetree/binding/pci/designware-pcie.txt Example: @@ -54,6 +65,24 @@ SoC specific DT Entry: num-lanes = <4>; }; +With using PHY framework: + pcie_phy0: pcie-phy@270000 { + ... + reg = <0x270000 0x1000>, <0x271000 0x40>; + reg-names = "phy", "block"; + ... + }; + + pcie@290000 { + ... + reg = <0x290000 0x1000>, <0x40000000 0x1000>; + reg-names = "elbi", "config"; + phys = <&pcie_phy0>; + ranges = <0x81000000 0 0 0x60001000 0 0x00010000 + 0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; + ... + }; + Board specific DT Entry: pcie@290000 { diff --git a/Documentation/devicetree/bindings/phy/brcm,nsp-usb3-phy.txt b/Documentation/devicetree/bindings/phy/brcm,nsp-usb3-phy.txt new file mode 100644 index 000000000000..e68ae5dec9c9 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm,nsp-usb3-phy.txt @@ -0,0 +1,39 @@ +Broadcom USB3 phy binding for northstar plus SoC +The USB3 phy is internal to the SoC and is accessed using mdio interface. + +Required mdio bus properties: +- reg: Should be 0x0 for SoC internal USB3 phy +- #address-cells: must be 1 +- #size-cells: must be 0 + +Required USB3 PHY properties: +- compatible: should be "brcm,nsp-usb3-phy" +- reg: USB3 Phy address on SoC internal MDIO bus and it should be 0x10. +- usb3-ctrl-syscon: handler of syscon node defining physical address + of usb3 control register. +- #phy-cells: must be 0 + +Required usb3 control properties: +- compatible: should be "brcm,nsp-usb3-ctrl" +- reg: offset and length of the control registers + +Example: + + mdio@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + + usb3_phy: usb-phy@10 { + compatible = "brcm,nsp-usb3-phy"; + reg = <0x10>; + usb3-ctrl-syscon = <&usb3_ctrl>; + #phy-cells = <0>; + status = "disabled"; + }; + }; + + usb3_ctrl: syscon@104408 { + compatible = "brcm,nsp-usb3-ctrl", "syscon"; + reg = <0x104408 0x3fc>; + }; diff --git a/Documentation/devicetree/bindings/phy/meson-usb2-phy.txt b/Documentation/devicetree/bindings/phy/meson8b-usb2-phy.txt index 9da5ea234154..5fa73b9d20f5 100644 --- a/Documentation/devicetree/bindings/phy/meson-usb2-phy.txt +++ b/Documentation/devicetree/bindings/phy/meson8b-usb2-phy.txt @@ -1,4 +1,4 @@ -* Amlogic USB2 PHY +* Amlogic Meson8b and GXBB USB2 PHY Required properties: - compatible: Depending on the platform this should be one of: @@ -16,10 +16,10 @@ Optional properties: Example: -usb0_phy: usb_phy@0 { +usb0_phy: usb-phy@c0000000 { compatible = "amlogic,meson-gxbb-usb2-phy"; #phy-cells = <0>; - reg = <0x0 0x0 0x0 0x20>; + reg = <0x0 0xc0000000 0x0 0x20>; resets = <&reset RESET_USB_OTG>; clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB0>; clock-names = "usb_general", "usb"; diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt b/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt new file mode 100644 index 000000000000..b3b75c1e6285 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt @@ -0,0 +1,84 @@ +Qualcomm's USB HS PHY + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: Should contain "qcom,usb-hs-phy" and more specifically one of the + following: + + "qcom,usb-hs-phy-apq8064" + "qcom,usb-hs-phy-msm8916" + "qcom,usb-hs-phy-msm8974" + +- #phy-cells: + Usage: required + Value type: <u32> + Definition: Should contain 0 + +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: Should contain clock specifier for the reference and sleep + clocks + +- clock-names: + Usage: required + Value type: <stringlist> + Definition: Should contain "ref" and "sleep" for the reference and sleep + clocks respectively + +- resets: + Usage: required + Value type: <prop-encoded-array> + Definition: Should contain the phy and POR resets + +- reset-names: + Usage: required + Value type: <stringlist> + Definition: Should contain "phy" and "por" for the phy and POR resets + respectively + +- v3p3-supply: + Usage: required + Value type: <phandle> + Definition: Should contain a reference to the 3.3V supply + +- v1p8-supply: + Usage: required + Value type: <phandle> + Definition: Should contain a reference to the 1.8V supply + +- extcon: + Usage: optional + Value type: <prop-encoded-array> + Definition: Should contain the vbus extcon + +- qcom,init-seq: + Usage: optional + Value type: <u8 array> + Definition: Should contain a sequence of ULPI address and value pairs to + program into the ULPI_EXT_VENDOR_SPECIFIC area. This is related + to Device Mode Eye Diagram test. The addresses are offsets + from the ULPI_EXT_VENDOR_SPECIFIC address, for example, + <0x1 0x53> would mean "write the value 0x53 to address 0x81". + +EXAMPLE + +otg: usb-controller { + ulpi { + phy { + compatible = "qcom,usb-hs-phy-msm8974", "qcom,usb-hs-phy"; + #phy-cells = <0>; + clocks = <&xo_board>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>; + clock-names = "ref", "sleep"; + resets = <&gcc GCC_USB2A_PHY_BCR>, <&otg 0>; + reset-names = "phy", "por"; + v3p3-supply = <&pm8941_l24>; + v1p8-supply = <&pm8941_l6>; + extcon = <&smbb>; + qcom,init-seq = /bits/ 8 <0x1 0x63>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-hsic-phy.txt b/Documentation/devicetree/bindings/phy/qcom,usb-hsic-phy.txt new file mode 100644 index 000000000000..3c7cb2be4b12 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,usb-hsic-phy.txt @@ -0,0 +1,65 @@ +Qualcomm's USB HSIC PHY + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: Should contain "qcom,usb-hsic-phy" and more specifically one of the + following: + + "qcom,usb-hsic-phy-mdm9615" + "qcom,usb-hsic-phy-msm8974" + +- #phy-cells: + Usage: required + Value type: <u32> + Definition: Should contain 0 + +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: Should contain clock specifier for phy, calibration and + a calibration sleep clock + +- clock-names: + Usage: required + Value type: <stringlist> + Definition: Should contain "phy, "cal" and "cal_sleep" + +- pinctrl-names: + Usage: required + Value type: <stringlist> + Definition: Should contain "init" and "default" in that order + +- pinctrl-0: + Usage: required + Value type: <prop-encoded-array> + Definition: List of pinctrl settings to apply to keep HSIC pins in a glitch + free state + +- pinctrl-1: + Usage: required + Value type: <prop-encoded-array> + Definition: List of pinctrl settings to apply to mux out the HSIC pins + +EXAMPLE + +usb-controller { + ulpi { + phy { + compatible = "qcom,usb-hsic-phy-msm8974", + "qcom,usb-hsic-phy"; + #phy-cells = <0>; + pinctrl-names = "init", "default"; + pinctrl-0 = <&hsic_sleep>; + pinctrl-1 = <&hsic_default>; + clocks = <&gcc GCC_USB_HSIC_CLK>, + <&gcc GCC_USB_HSIC_IO_CAL_CLK>, + <&gcc GCC_USB_HSIC_IO_CAL_SLEEP_CLK>; + clock-names = "phy", "cal", "cal_sleep"; + assigned-clocks = <&gcc GCC_USB_HSIC_IO_CAL_CLK>; + assigned-clock-rates = <960000>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt index 9872ba8546bd..ab80bfe31cb3 100644 --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt @@ -191,3 +191,20 @@ Example: usbdrdphy0 = &usb3_phy0; usbdrdphy1 = &usb3_phy1; }; + +Samsung Exynos SoC series PCIe PHY controller +-------------------------------------------------- +Required properties: +- compatible : Should be set to "samsung,exynos5440-pcie-phy" +- #phy-cells : Must be zero +- reg : a register used by phy driver. + - First is for phy register, second is for block register. +- reg-names : Must be set to "phy" and "block". + +Example: + pcie_phy0: pcie-phy@270000 { + #phy-cells = <0>; + compatible = "samsung,exynos5440-pcie-phy"; + reg = <0x270000 0x1000>, <0x271000 0x40>; + reg-names = "phy", "block"; + }; diff --git a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt index 287150db6db4..e42334258185 100644 --- a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt @@ -10,6 +10,7 @@ Required properties: * allwinner,sun8i-a23-usb-phy * allwinner,sun8i-a33-usb-phy * allwinner,sun8i-h3-usb-phy + * allwinner,sun8i-v3s-usb-phy * allwinner,sun50i-a64-usb-phy - reg : a list of offset + length pairs - reg-names : diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index 1685821eea41..2fd688c8dbdb 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -6,7 +6,7 @@ the first two functions being GPIO in and out. The configuration on the pins includes drive strength and pull-up. Required properties: -- compatible: Should be one of the followings (depending on you SoC): +- compatible: Should be one of the following (depending on your SoC): "allwinner,sun4i-a10-pinctrl" "allwinner,sun5i-a10s-pinctrl" "allwinner,sun5i-a13-pinctrl" @@ -23,11 +23,26 @@ Required properties: "allwinner,sun8i-h3-pinctrl" "allwinner,sun8i-h3-r-pinctrl" "allwinner,sun50i-a64-pinctrl" + "allwinner,sun50i-h5-r-pinctrl" "nextthing,gr8-pinctrl" - reg: Should contain the register physical address and length for the pin controller. +- clocks: phandle to the clocks feeding the pin controller: + - "apb": the gated APB parent clock + - "hosc": the high frequency oscillator in the system + - "losc": the low frequency oscillator in the system + +Note: For backward compatibility reasons, the hosc and losc clocks are only +required if you need to use the optional input-debounce property. Any new +device tree should set them. + +Optional properties: + - input-debounce: Array of debouncing periods in microseconds. One period per + irq bank found in the controller. 0 if no setup required. + + Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices. @@ -37,6 +52,22 @@ pins it needs, and how they should be configured, with regard to muxer configuration, drive strength and pullups. If one of these options is not set, its actual value will be unspecified. +This driver supports the generic pin multiplexing and configuration +bindings. For details on each properties, you can refer to +./pinctrl-bindings.txt. + +Required sub-node properties: + - pins + - function + +Optional sub-node properties: + - bias-disable + - bias-pull-up + - bias-pull-down + - drive-strength + +*** Deprecated pin configuration and multiplexing binding + Required subnode-properties: - allwinner,pins: List of strings containing the pin name. diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt index b7a93e80a302..9a8a45d9d8ab 100644 --- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt @@ -98,6 +98,8 @@ DRIVE_STRENGTH (3 << 5): indicate the drive strength of the pin using the 01 - Low 10 - Medium 11 - High +OUTPUT (1 << 7): indicate this pin need to be configured as an output. +OUTPUT_VAL (1 << 8): output val (1 = high, 0 = low) DEBOUNCE (1 << 16): indicate this pin needs debounce. DEBOUNCE_VAL (0x3fff << 17): debounce value. diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt index 457b2c68d47b..8c5d27c5b562 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt @@ -19,7 +19,7 @@ iomuxc: iomuxc@30330000 { reg = <0x30330000 0x10000>; }; -Pheriparials using pads from iomuxc-lpsr support low state retention power +Peripherals using pads from iomuxc-lpsr support low state retention power state, under LPSR mode GPIO's state of pads are retain. Please refer to fsl,imx-pinctrl.txt in this directory for common binding part diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt new file mode 100644 index 000000000000..97aef67ee769 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt @@ -0,0 +1,46 @@ +* Marvell 98dx3236 pinctrl driver for mpp + +Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding +part and usage + +Required properties: +- compatible: "marvell,98dx3236-pinctrl" or "marvell,98dx4251-pinctrl" +- reg: register specifier of MPP registers + +This driver supports all 98dx3236, 98dx3336 and 98dx4251 variants + +name pins functions +================================================================================ +mpp0 0 gpo, spi0(mosi), dev(ad8) +mpp1 1 gpio, spi0(miso), dev(ad9) +mpp2 2 gpo, spi0(sck), dev(ad10) +mpp3 3 gpio, spi0(cs0), dev(ad11) +mpp4 4 gpio, spi0(cs1), smi(mdc), dev(cs0) +mpp5 5 gpio, pex(rsto), sd0(cmd), dev(bootcs) +mpp6 6 gpo, sd0(clk), dev(a2) +mpp7 7 gpio, sd0(d0), dev(ale0) +mpp8 8 gpio, sd0(d1), dev(ale1) +mpp9 9 gpio, sd0(d2), dev(ready0) +mpp10 10 gpio, sd0(d3), dev(ad12) +mpp11 11 gpio, uart1(rxd), uart0(cts), dev(ad13) +mpp12 12 gpo, uart1(txd), uart0(rts), dev(ad14) +mpp13 13 gpio, intr(out), dev(ad15) +mpp14 14 gpio, i2c0(sck) +mpp15 15 gpio, i2c0(sda) +mpp16 16 gpo, dev(oe) +mpp17 17 gpo, dev(clkout) +mpp18 18 gpio, uart1(txd) +mpp19 19 gpio, uart1(rxd), dev(rb) +mpp20 20 gpo, dev(we0) +mpp21 21 gpo, dev(ad0) +mpp22 22 gpo, dev(ad1) +mpp23 23 gpo, dev(ad2) +mpp24 24 gpo, dev(ad3) +mpp25 25 gpo, dev(ad4) +mpp26 26 gpo, dev(ad5) +mpp27 27 gpo, dev(ad6) +mpp28 28 gpo, dev(ad7) +mpp29 29 gpo, dev(a0) +mpp30 30 gpo, dev(a1) +mpp31 31 gpio, slv_smi(mdc), smi(mdc), dev(we1) +mpp32 32 gpio, slv_smi(mdio), smi(mdio), dev(cs1) diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt index 730444a9a4de..6c0ea155b708 100644 --- a/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt @@ -44,16 +44,16 @@ mpp16 16 gpio, sdio(d2), uart0(cts), uart1(rxd), mii(crs) mpp17 17 gpio, sdio(d3) mpp18 18 gpo, nand(io0) mpp19 19 gpo, nand(io1) -mpp20 20 gpio, mii(rxerr) -mpp21 21 gpio, audio(spdifi) -mpp22 22 gpio, audio(spdifo) -mpp23 23 gpio, audio(rmclk) -mpp24 24 gpio, audio(bclk) -mpp25 25 gpio, audio(sdo) -mpp26 26 gpio, audio(lrclk) -mpp27 27 gpio, audio(mclk) -mpp28 28 gpio, audio(sdi) -mpp29 29 gpio, audio(extclk) +mpp35 35 gpio, mii(rxerr) +mpp36 36 gpio, audio(spdifi) +mpp37 37 gpio, audio(spdifo) +mpp38 38 gpio, audio(rmclk) +mpp39 39 gpio, audio(bclk) +mpp40 40 gpio, audio(sdo) +mpp41 41 gpio, audio(lrclk) +mpp42 42 gpio, audio(mclk) +mpp43 43 gpio, audio(sdi) +mpp44 44 gpio, audio(extclk) * Marvell Kirkwood 88f6190 diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt index fe7fe0b03cfb..2392557ede27 100644 --- a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt @@ -7,6 +7,8 @@ Required properties for the root node: "amlogic,meson8b-aobus-pinctrl" "amlogic,meson-gxbb-periphs-pinctrl" "amlogic,meson-gxbb-aobus-pinctrl" + "amlogic,meson-gxl-periphs-pinctrl" + "amlogic,meson-gxl-aobus-pinctrl" - reg: address and size of registers controlling irq functionality === GPIO sub-nodes === diff --git a/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt index d6074321f730..09e81a95bbfd 100644 --- a/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt @@ -9,7 +9,7 @@ used for a specific device or function. This node represents configurations of pins, optional function, and optional mux related configuration. Required properties for pin controller node: - - compatible: "oxsemi,ox810se-pinctrl" + - compatible: "oxsemi,ox810se-pinctrl" or "oxsemi,ox820-pinctrl" - oxsemi,sys-ctrl: a phandle to the system controller syscon node Required properties for pin configuration sub-nodes: diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt index 2ad18c4ea55c..b98e6f030da8 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt @@ -1,25 +1,38 @@ +====================== Aspeed Pin Controllers ----------------------- +====================== The Aspeed SoCs vary in functionality inside a generation but have a common mux device register layout. -Required properties: -- compatible : Should be any one of the following: - "aspeed,ast2400-pinctrl" - "aspeed,g4-pinctrl" - "aspeed,ast2500-pinctrl" - "aspeed,g5-pinctrl" +Required properties for g4: +- compatible : Should be one of the following: + "aspeed,ast2400-pinctrl" + "aspeed,g4-pinctrl" -The pin controller node should be a child of a syscon node with the required +Required properties for g5: +- compatible : Should be one of the following: + "aspeed,ast2500-pinctrl" + "aspeed,g5-pinctrl" + +- aspeed,external-nodes: A cell of phandles to external controller nodes: + 0: compatible with "aspeed,ast2500-gfx", "syscon" + 1: compatible with "aspeed,ast2500-lhc", "syscon" + +The pin controller node should be the child of a syscon node with the required property: -- compatible: "syscon", "simple-mfd" + +- compatible : Should be one of the following: + "aspeed,ast2400-scu", "syscon", "simple-mfd" + "aspeed,g4-scu", "syscon", "simple-mfd" + "aspeed,ast2500-scu", "syscon", "simple-mfd" + "aspeed,g5-scu", "syscon", "simple-mfd" Refer to the the bindings described in Documentation/devicetree/bindings/mfd/syscon.txt Subnode Format --------------- +============== The required properties of child nodes are (as defined in pinctrl-bindings): - function @@ -31,26 +44,43 @@ supported: aspeed,ast2400-pinctrl, aspeed,g4-pinctrl: -ACPI BMCINT DDCCLK DDCDAT FLACK FLBUSY FLWP GPID0 GPIE0 GPIE2 GPIE4 GPIE6 I2C10 -I2C11 I2C12 I2C13 I2C3 I2C4 I2C5 I2C6 I2C7 I2C8 I2C9 LPCPD LPCPME LPCSMI MDIO1 -MDIO2 NCTS1 NCTS3 NCTS4 NDCD1 NDCD3 NDCD4 NDSR1 NDSR3 NDTR1 NDTR3 NRI1 NRI3 -NRI4 NRTS1 NRTS3 PWM0 PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 RGMII1 RMII1 ROM16 -ROM8 ROMCS1 ROMCS2 ROMCS3 ROMCS4 RXD1 RXD3 RXD4 SD1 SGPMI SIOPBI SIOPBO TIMER3 -TIMER5 TIMER6 TIMER7 TIMER8 TXD1 TXD3 TXD4 UART6 VGAHS VGAVS VPI18 VPI24 VPI30 -VPO12 VPO24 +ACPI ADC0 ADC1 ADC10 ADC11 ADC12 ADC13 ADC14 ADC15 ADC2 ADC3 ADC4 ADC5 ADC6 +ADC7 ADC8 ADC9 BMCINT DDCCLK DDCDAT EXTRST FLACK FLBUSY FLWP GPID GPID0 GPID2 +GPID4 GPID6 GPIE0 GPIE2 GPIE4 GPIE6 I2C10 I2C11 I2C12 I2C13 I2C14 I2C3 I2C4 +I2C5 I2C6 I2C7 I2C8 I2C9 LPCPD LPCPME LPCRST LPCSMI MAC1LINK MAC2LINK MDIO1 +MDIO2 NCTS1 NCTS2 NCTS3 NCTS4 NDCD1 NDCD2 NDCD3 NDCD4 NDSR1 NDSR2 NDSR3 NDSR4 +NDTR1 NDTR2 NDTR3 NDTR4 NDTS4 NRI1 NRI2 NRI3 NRI4 NRTS1 NRTS2 NRTS3 OSCCLK PWM0 +PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 RGMII1 RGMII2 RMII1 RMII2 ROM16 ROM8 ROMCS1 +ROMCS2 ROMCS3 ROMCS4 RXD1 RXD2 RXD3 RXD4 SALT1 SALT2 SALT3 SALT4 SD1 SD2 SGPMCK +SGPMI SGPMLD SGPMO SGPSCK SGPSI0 SGPSI1 SGPSLD SIOONCTRL SIOPBI SIOPBO SIOPWREQ +SIOPWRGD SIOS3 SIOS5 SIOSCI SPI1 SPI1DEBUG SPI1PASSTHRU SPICS1 TIMER3 TIMER4 +TIMER5 TIMER6 TIMER7 TIMER8 TXD1 TXD2 TXD3 TXD4 UART6 USBCKI VGABIOS_ROM VGAHS +VGAVS VPI18 VPI24 VPI30 VPO12 VPO24 WDTRST1 WDTRST2 aspeed,ast2500-pinctrl, aspeed,g5-pinctrl: -GPID0 GPID2 GPIE0 I2C10 I2C11 I2C12 I2C13 I2C14 I2C3 I2C4 I2C5 I2C6 I2C7 I2C8 -I2C9 MAC1LINK MDIO1 MDIO2 OSCCLK PEWAKE PWM0 PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 -RGMII1 RGMII2 RMII1 RMII2 SD1 SPI1 SPI1DEBUG SPI1PASSTHRU TIMER4 TIMER5 TIMER6 -TIMER7 TIMER8 VGABIOSROM - - -Examples: +ACPI ADC0 ADC1 ADC10 ADC11 ADC12 ADC13 ADC14 ADC15 ADC2 ADC3 ADC4 ADC5 ADC6 +ADC7 ADC8 ADC9 BMCINT DDCCLK DDCDAT ESPI FWSPICS1 FWSPICS2 GPID0 GPID2 GPID4 +GPID6 GPIE0 GPIE2 GPIE4 GPIE6 I2C10 I2C11 I2C12 I2C13 I2C14 I2C3 I2C4 I2C5 I2C6 +I2C7 I2C8 I2C9 LAD0 LAD1 LAD2 LAD3 LCLK LFRAME LPCHC LPCPD LPCPLUS LPCPME +LPCRST LPCSMI LSIRQ MAC1LINK MAC2LINK MDIO1 MDIO2 NCTS1 NCTS2 NCTS3 NCTS4 NDCD1 +NDCD2 NDCD3 NDCD4 NDSR1 NDSR2 NDSR3 NDSR4 NDTR1 NDTR2 NDTR3 NDTR4 NRI1 NRI2 +NRI3 NRI4 NRTS1 NRTS2 NRTS3 NRTS4 OSCCLK PEWAKE PNOR PWM0 PWM1 PWM2 PWM3 PWM4 +PWM5 PWM6 PWM7 RGMII1 RGMII2 RMII1 RMII2 RXD1 RXD2 RXD3 RXD4 SALT1 SALT10 +SALT11 SALT12 SALT13 SALT14 SALT2 SALT3 SALT4 SALT5 SALT6 SALT7 SALT8 SALT9 +SCL1 SCL2 SD1 SD2 SDA1 SDA2 SGPS1 SGPS2 SIOONCTRL SIOPBI SIOPBO SIOPWREQ +SIOPWRGD SIOS3 SIOS5 SIOSCI SPI1 SPI1CS1 SPI1DEBUG SPI1PASSTHRU SPI2CK SPI2CS0 +SPI2CS1 SPI2MISO SPI2MOSI TIMER3 TIMER4 TIMER5 TIMER6 TIMER7 TIMER8 TXD1 TXD2 +TXD3 TXD4 UART6 USBCKI VGABIOSROM VGAHS VGAVS VPI24 VPO WDTRST1 WDTRST2 + +Examples +======== + +g4 Example +---------- syscon: scu@1e6e2000 { - compatible = "syscon", "simple-mfd"; + compatible = "aspeed,ast2400-scu", "syscon", "simple-mfd"; reg = <0x1e6e2000 0x1a8>; pinctrl: pinctrl { @@ -63,5 +93,56 @@ syscon: scu@1e6e2000 { }; }; +g5 Example +---------- + +ahb { + apb { + syscon: scu@1e6e2000 { + compatible = "aspeed,ast2500-scu", "syscon", "simple-mfd"; + reg = <0x1e6e2000 0x1a8>; + + pinctrl: pinctrl { + compatible = "aspeed,g5-pinctrl"; + aspeed,external-nodes = <&gfx &lhc>; + + pinctrl_i2c3_default: i2c3_default { + function = "I2C3"; + groups = "I2C3"; + }; + }; + }; + + gfx: display@1e6e6000 { + compatible = "aspeed,ast2500-gfx", "syscon"; + reg = <0x1e6e6000 0x1000>; + }; + }; + + lpc: lpc@1e789000 { + compatible = "aspeed,ast2500-lpc", "simple-mfd"; + reg = <0x1e789000 0x1000>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x1e789000 0x1000>; + + lpc_host: lpc-host@80 { + compatible = "aspeed,ast2500-lpc-host", "simple-mfd", "syscon"; + reg = <0x80 0x1e0>; + reg-io-width = <4>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x80 0x1e0>; + + lhc: lhc@20 { + compatible = "aspeed,ast2500-lhc"; + reg = <0x20 0x24 0x48 0x8>; + }; + }; + }; +}; + Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices. diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt index b73c96d24f59..bf3f7b014724 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt @@ -97,6 +97,11 @@ For example: }; == Pin controller devices == +Required properties: See the pin controller driver specific documentation + +Optional properties: +#pinctrl-cells: Number of pin control cells in addition to the index within the + pin controller device instance Pin controller devices should contain the pin configuration nodes that client devices reference. @@ -119,7 +124,8 @@ For example: The contents of each of those pin configuration child nodes is defined entirely by the binding for the individual pin controller device. There -exists no common standard for this content. +exists no common standard for this content. The pinctrl framework only +provides generic helper bindings that the pin controller driver can use. The pin configuration nodes need not be direct children of the pin controller device; they may be grandchildren, for example. Whether this is legal, and @@ -156,6 +162,42 @@ state_2_node_a { pins = "mfio29", "mfio30"; }; +Optionally an altenative binding can be used if more suitable depending on the +pin controller hardware. For hardaware where there is a large number of identical +pin controller instances, naming each pin and function can easily become +unmaintainable. This is especially the case if the same controller is used for +different pins and functions depending on the SoC revision and packaging. + +For cases like this, the pin controller driver may use pinctrl-pin-array helper +binding with a hardware based index and a number of pin configuration values: + +pincontroller { + ... /* Standard DT properties for the device itself elided */ + #pinctrl-cells = <2>; + + state_0_node_a { + pinctrl-pin-array = < + 0 A_DELAY_PS(0) G_DELAY_PS(120) + 4 A_DELAY_PS(0) G_DELAY_PS(360) + ... + >; + }; + ... +}; + +Above #pinctrl-cells specifies the number of value cells in addition to the +index of the registers. This is similar to the interrupts-extended binding with +one exception. There is no need to specify the phandle for each entry as that +is already known as the defined pins are always children of the pin controller +node. Further having the phandle pointing to another pin controller would not +currently work as the pinctrl framework uses named modes to group pins for each +pin control device. + +The index for pinctrl-pin-array must relate to the hardware for the pinctrl +registers, and must not be a virtual index of pin instances. The reason for +this is to avoid mapping of the index in the dts files and the pin controller +driver as it can change. + == Generic pin configuration node content == Many data items that are represented in a pin configuration node are common diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-palmas.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-palmas.txt index caf297bee1fb..c28d4eb83b76 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-palmas.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-palmas.txt @@ -35,6 +35,15 @@ Optional properties: - ti,palmas-enable-dvfs2: Enable DVFS2. Configure pins for DVFS2 mode. Selection primary or secondary function associated to GPADC_START and SYSEN2 pin/pad for DVFS2 interface +- ti,palmas-override-powerhold: This is applicable for PMICs for which + GPIO7 is configured in POWERHOLD mode which has higher priority + over DEV_ON bit and keeps the PMIC supplies on even after the DEV_ON + bit is turned off. This property enables driver to over ride the + POWERHOLD value to GPIO7 so as to turn off the PMIC in power off + scenarios. So for GPIO7 if ti,palmas-override-powerhold is set + then the GPIO_7 field should never be muxed to anything else. + It should be set to POWERHOLD by default and only in case of + power off scenarios the driver will over ride the mux value. This binding uses the following generic properties as defined in pinctrl-bindings.txt: diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt index 66dcaa9efd74..e705acd3612c 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt @@ -7,6 +7,9 @@ Required properties: - reg : offset and length of the register set for the mux registers +- #pinctrl-cells : number of cells in addition to the index, set to 1 + for pinctrl-single,pins and 2 for pinctrl-single,bits + - pinctrl-single,register-width : pinmux register access width in bits - pinctrl-single,function-mask : mask of allowed pinmux function bits diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt new file mode 100644 index 000000000000..bf76867168e9 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt @@ -0,0 +1,74 @@ +SEMTECH SX150x GPIO expander bindings + +Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and +../interrupt-controller/interrupts.txt for generic information regarding +pin controller, GPIO, and interrupt bindings. + +Required properties: +- compatible: should be one of : + "semtech,sx1501q", + "semtech,sx1502q", + "semtech,sx1503q", + "semtech,sx1504q", + "semtech,sx1505q", + "semtech,sx1506q", + "semtech,sx1507q", + "semtech,sx1508q", + "semtech,sx1509q". + +- reg: The I2C slave address for this device. + +- #gpio-cells: Should be 2. The first cell is the GPIO number and the + second cell is used to specify optional parameters: + bit 0: polarity (0: normal, 1: inverted) + +- gpio-controller: Marks the device as a GPIO controller. + +Optional properties : +- interrupt-parent: phandle of the parent interrupt controller. + +- interrupts: Interrupt specifier for the controllers interrupt. + +- interrupt-controller: Marks the device as a interrupt controller. + +- semtech,probe-reset: Will trigger a reset of the GPIO expander on probe, + only for sx1507q, sx1508q and sx1509q + +The GPIO expander can optionally be used as an interrupt controller, in +which case it uses the default two cell specifier. + +Required properties for pin configuration sub-nodes: + - pins: List of pins to which the configuration applies. + +Optional properties for pin configuration sub-nodes: +---------------------------------------------------- + - bias-disable: disable any pin bias, except the OSCIO pin + - bias-pull-up: pull up the pin, except the OSCIO pin + - bias-pull-down: pull down the pin, except the OSCIO pin + - bias-pull-pin-default: use pin-default pull state, except the OSCIO pin + - drive-push-pull: drive actively high and low + - drive-open-drain: drive with open drain only for sx1507q, sx1508q and sx1509q and except the OSCIO pin + - output-low: set the pin to output mode with low level + - output-high: set the pin to output mode with high level + +Example: + + i2c0gpio-expander@20{ + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "semtech,sx1506q"; + reg = <0x20>; + interrupt-parent = <&gpio_1>; + interrupts = <16 0>; + + gpio-controller; + interrupt-controller; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio1_cfg_pins>; + + gpio1_cfg_pins: gpio1-cfg { + pins = "gpio1"; + bias-pull-up; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8994-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8994-pinctrl.txt new file mode 100644 index 000000000000..13cd629f896e --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8994-pinctrl.txt @@ -0,0 +1,177 @@ +Qualcomm MSM8994 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +MSM8994 platform. + +- compatible: + Usage: required + Value type: <string> + Definition: Should contain one of: + "qcom,msm8992-pinctrl", + "qcom,msm8994-pinctrl". + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the TLMM register space. + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: <none> + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/interrupt-controller/irq.h> + +- gpio-controller: + Usage: required + Value type: <none> + Definition: identifies this node as a gpio controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/gpio/gpio.h> + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. + + Valid pins are: + gpio0-gpio145 + Supports mux, bias and drive-strength + + sdc1_clk, sdc1_cmd, sdc1_data sdc1_rclk, sdc2_clk, + sdc2_cmd, sdc2_data + Supports bias and drive-strength + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Functions are only valid for gpio pins. + Valid values are: + + audio_ref_clk, blsp_i2c1, blsp_i2c2, blsp_i2c3, blsp_i2c4, blsp_i2c5, + blsp_i2c6, blsp_i2c7, blsp_i2c8, blsp_i2c9, blsp_i2c10, blsp_i2c11, + blsp_i2c12, blsp_spi1, blsp_spi1_cs1, blsp_spi1_cs2, blsp_spi1_cs3, + blsp_spi2, blsp_spi2_cs1, blsp_spi2_cs2, blsp_spi2_cs3, blsp_spi3, + blsp_spi4, blsp_spi5, blsp_spi6, blsp_spi7, blsp_spi8, blsp_spi9, + blsp_spi10, blsp_spi10_cs1, blsp_spi10_cs2, blsp_spi10_cs3, blsp_spi11, + blsp_spi12, blsp_uart1, blsp_uart2, blsp_uart3, blsp_uart4, blsp_uart5, + blsp_uart6, blsp_uart7, blsp_uart8, blsp_uart9, blsp_uart10, blsp_uart11, + blsp_uart12, blsp_uim1, blsp_uim2, blsp_uim3, blsp_uim4, blsp_uim5, + blsp_uim6, blsp_uim7, blsp_uim8, blsp_uim9, blsp_uim10, blsp_uim11, + blsp_uim12, blsp11_i2c_scl_b, blsp11_i2c_sda_b, blsp11_uart_rx_b, + blsp11_uart_tx_b, cam_mclk0, cam_mclk1, cam_mclk2, cam_mclk3, + cci_async_in0, cci_async_in1, cci_async_in2, cci_i2c0, cci_i2c1, + cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4, + gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a, gcc_gp2_clk_b, gcc_gp3_clk_a, + gcc_gp3_clk_b, gp_mn, gp_pdm0, gp_pdm1, gp_pdm2, gp0_clk, + gp1_clk, gps_tx, gsm_tx, hdmi_cec, hdmi_ddc, hdmi_hpd, hdmi_rcv, + mdp_vsync, mss_lte, nav_pps, nav_tsync, qdss_cti_trig_in_a, + qdss_cti_trig_in_b, qdss_cti_trig_in_c, qdss_cti_trig_in_d, + qdss_cti_trig_out_a, qdss_cti_trig_out_b, qdss_cti_trig_out_c, + qdss_cti_trig_out_d, qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, + qdss_tracectl_b, qdss_tracedata_a, qdss_tracedata_b, qua_mi2s, pci_e0, + pci_e1, pri_mi2s, sdc4, sec_mi2s, slimbus, spkr_i2s, ter_mi2s, tsif1, + tsif2, uim_batt_alarm, uim1, uim2, uim3, uim4, gpio + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull down. + +- bias-pull-up: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull up. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + Not valid for sdc pins. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + Not valid for sdc pins. + +- drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + msmgpio: pinctrl@fd510000 { + compatible = "qcom,msm8994-pinctrl"; + reg = <0xfd510000 0x4000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + + blsp1_uart2_default: blsp1_uart2_default { + pinmux { + pins = "gpio4", "gpio5"; + function = "blsp_uart2"; + }; + pinconf { + pins = "gpio4", "gpio5"; + drive-strength = <16>; + bias-disable; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt index c68b9554561f..4722bc61a1a2 100644 --- a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt @@ -19,10 +19,11 @@ The pins are grouped into up to 5 individual pin banks which need to be defined as gpio sub-nodes of the pinmux controller. Required properties for iomux controller: - - compatible: one of "rockchip,rk2928-pinctrl", "rockchip,rk3066a-pinctrl" - "rockchip,rk3066b-pinctrl", "rockchip,rk3188-pinctrl" - "rockchip,rk3228-pinctrl", "rockchip,rk3288-pinctrl" - "rockchip,rk3368-pinctrl", "rockchip,rk3399-pinctrl" + - compatible: one of "rockchip,rk1108-pinctrl", "rockchip,rk2928-pinctrl" + "rockchip,rk3066a-pinctrl", "rockchip,rk3066b-pinctrl" + "rockchip,rk3188-pinctrl", "rockchip,rk3228-pinctrl" + "rockchip,rk3288-pinctrl", "rockchip,rk3368-pinctrl" + "rockchip,rk3399-pinctrl" - rockchip,grf: phandle referencing a syscon providing the "general register files" diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt index d49e22d2a8b5..5e00a21de2bf 100644 --- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt @@ -13,17 +13,37 @@ Required Properties: - "samsung,s3c2450-pinctrl": for S3C2450-compatible pin-controller, - "samsung,s3c64xx-pinctrl": for S3C64xx-compatible pin-controller, - "samsung,s5pv210-pinctrl": for S5PV210-compatible pin-controller, + - "samsung,exynos3250-pinctrl": for Exynos3250 compatible pin-controller. - "samsung,exynos4210-pinctrl": for Exynos4210 compatible pin-controller. - "samsung,exynos4x12-pinctrl": for Exynos4x12 compatible pin-controller. - "samsung,exynos5250-pinctrl": for Exynos5250 compatible pin-controller. - "samsung,exynos5260-pinctrl": for Exynos5260 compatible pin-controller. - "samsung,exynos5410-pinctrl": for Exynos5410 compatible pin-controller. - "samsung,exynos5420-pinctrl": for Exynos5420 compatible pin-controller. + - "samsung,exynos5433-pinctrl": for Exynos5433 compatible pin-controller. - "samsung,exynos7-pinctrl": for Exynos7 compatible pin-controller. - reg: Base address of the pin controller hardware module and length of the address space it occupies. + - reg: Second base address of the pin controller if the specific registers + of the pin controller are separated into the different base address. + + Eg: GPF[1-5] of Exynos5433 are separated into the two base address. + - First base address is for GPAx and GPF[1-5] external interrupt + registers. + - Second base address is for GPF[1-5] pinctrl registers. + + pinctrl_0: pinctrl@10580000 { + compatible = "samsung,exynos5433-pinctrl"; + reg = <0x10580000 0x1a20>, <0x11090000 0x100>; + + wakeup-interrupt-controller { + compatible = "samsung,exynos7-wakeup-eint"; + interrupts = <0 16 0>; + }; + }; + - Pin banks as child nodes: Pin banks of the controller are represented by child nodes of the controller node. Bank name is taken from name of the node. Each bank node must contain following properties: diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt index b24583aa34c3..eac20aa33907 100644 --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt @@ -8,8 +8,9 @@ controllers onto these pads. Pin controller node: Required properies: - compatible: value should be one of the following: - (a) "st,stm32f429-pinctrl" - (b) "st,stm32f746-pinctrl" + "st,stm32f429-pinctrl" + "st,stm32f746-pinctrl" + "st,stm32h743-pinctrl" - #address-cells: The value of this property must be 1 - #size-cells : The value of this property must be 1 - ranges : defines mapping between pin controller node (parent) to @@ -37,8 +38,23 @@ Optional properties: - st,syscfg: Should be phandle/offset pair. The phandle to the syscon node which includes IRQ mux selection register, and the offset of the IRQ mux selection register. + - ngpios: Number of gpios in a bank (to use if bank gpio numbers is less + than 16). + - gpio-ranges: Define a dedicated mapping between a pin-controller and + a gpio controller. Format is <&phandle a b c> with: + -(phandle): phandle of pin-controller. + -(a): gpio base offset in range. + -(b): pin base offset in range. + -(c): gpio count in range + This entry has to be used either if there are holes inside a bank: + GPIOB0/B1/B2/B14/B15 (see example 2) + or if banks are not contiguous: + GPIOA/B/C/E... + NOTE: If "gpio-ranges" is used for a gpio controller, all gpio-controller + have to use a "gpio-ranges" entry. + More details in Documentation/devicetree/bindings/gpio/gpio.txt. -Example: +Example 1: #include <dt-bindings/pinctrl/stm32f429-pinfunc.h> ... @@ -60,6 +76,43 @@ Example: pin-functions nodes follow... }; +Example 2: +#include <dt-bindings/pinctrl/stm32f429-pinfunc.h> +... + + pinctrl: pin-controller { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,stm32f429-pinctrl"; + ranges = <0 0x40020000 0x3000>; + pins-are-numbered; + + gpioa: gpio@40020000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x0 0x400>; + resets = <&reset_ahb1 0>; + st,bank-name = "GPIOA"; + gpio-ranges = <&pinctrl 0 0 16>; + }; + + gpiob: gpio@40020400 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x0 0x400>; + resets = <&reset_ahb1 0>; + st,bank-name = "GPIOB"; + ngpios = 4; + gpio-ranges = <&pinctrl 0 16 3>, + <&pinctrl 14 30 2>; + }; + + + ... + pin-functions nodes follow... + }; + + Contents of function subnode node: ---------------------------------- Subnode format diff --git a/Documentation/devicetree/bindings/pinctrl/ti,da850-pupd.txt b/Documentation/devicetree/bindings/pinctrl/ti,da850-pupd.txt new file mode 100644 index 000000000000..7f2980567c9f --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/ti,da850-pupd.txt @@ -0,0 +1,55 @@ +* Pin configuration for TI DA850/OMAP-L138/AM18x + +These SoCs have a separate controller for setting bias (internal pullup/down). +Bias can only be selected for groups rather than individual pins. + +Required Properties: + + - compatible: Must be "ti,da850-pupd" + - reg: Base address and length of the memory resource used by the pullup/down + controller hardware module. + +The controller node also acts as a container for pin group configuration nodes. +The names of these groups are ignored. + +Pin Group Node Properties: + +- groups: An array of strings, each string containing the name of a pin group. + Valid names are "cp0".."cp31". + +The pin configuration parameters use the generic pinconf bindings defined in +pinctrl-bindings.txt in this directory. The supported parameters are +bias-disable, bias-pull-up, bias-pull-down. + + +Example +------- + +In common dtsi file: + + pinconf: pin-controller@22c00c { + compatible = "ti,da850-pupd"; + reg = <0x22c00c 0x8>; + }; + +In board-specific file: + + &pinconf { + pinctrl-0 = <&pinconf_bias_groups>; + pinctrl-names = "default"; + + pinconf_bias_groups: bias-groups { + pull-up { + groups = "cp30", "cp31"; + bias-pull-up; + }; + pull-down { + groups = "cp29", "cp28"; + bias-pull-down; + }; + disable { + groups = "cp27", "cp26"; + bias-disable; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/ti,iodelay.txt b/Documentation/devicetree/bindings/pinctrl/ti,iodelay.txt new file mode 100644 index 000000000000..c3ed1232b6a3 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/ti,iodelay.txt @@ -0,0 +1,47 @@ +* Pin configuration for TI IODELAY controller + +TI dra7 based SoCs such as am57xx have a controller for setting the IO delay +for each pin. For most part the IO delay values are programmed by the bootloader, +but some pins need to be configured dynamically by the kernel such as the +MMC pins. + +Required Properties: + + - compatible: Must be "ti,dra7-iodelay" + - reg: Base address and length of the memory resource used + - #address-cells: Number of address cells + - #size-cells: Size of cells + - #pinctrl-cells: Number of pinctrl cells, must be 2. See also + Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +Example +------- + +In the SoC specific dtsi file: + + dra7_iodelay_core: padconf@4844a000 { + compatible = "ti,dra7-iodelay"; + reg = <0x4844a000 0x0d1c>; + #address-cells = <1>; + #size-cells = <0>; + #pinctrl-cells = <2>; + }; + +In board-specific file: + +&dra7_iodelay_core { + mmc2_iodelay_3v3_conf: mmc2_iodelay_3v3_conf { + pinctrl-pin-array = < + 0x18c A_DELAY_PS(0) G_DELAY_PS(120) /* CFG_GPMC_A19_IN */ + 0x1a4 A_DELAY_PS(265) G_DELAY_PS(360) /* CFG_GPMC_A20_IN */ + 0x1b0 A_DELAY_PS(0) G_DELAY_PS(120) /* CFG_GPMC_A21_IN */ + 0x1bc A_DELAY_PS(0) G_DELAY_PS(120) /* CFG_GPMC_A22_IN */ + 0x1c8 A_DELAY_PS(287) G_DELAY_PS(420) /* CFG_GPMC_A23_IN */ + 0x1d4 A_DELAY_PS(144) G_DELAY_PS(240) /* CFG_GPMC_A24_IN */ + 0x1e0 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_GPMC_A25_IN */ + 0x1ec A_DELAY_PS(120) G_DELAY_PS(0) /* CFG_GPMC_A26_IN */ + 0x1f8 A_DELAY_PS(120) G_DELAY_PS(180) /* CFG_GPMC_A27_IN */ + 0x360 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_GPMC_CS1_IN */ + >; + }; +}; diff --git a/Documentation/devicetree/bindings/power/domain-idle-state.txt b/Documentation/devicetree/bindings/power/domain-idle-state.txt new file mode 100644 index 000000000000..eefc7ed22ca2 --- /dev/null +++ b/Documentation/devicetree/bindings/power/domain-idle-state.txt @@ -0,0 +1,33 @@ +PM Domain Idle State Node: + +A domain idle state node represents the state parameters that will be used to +select the state when there are no active components in the domain. + +The state node has the following parameters - + +- compatible: + Usage: Required + Value type: <string> + Definition: Must be "domain-idle-state". + +- entry-latency-us + Usage: Required + Value type: <prop-encoded-array> + Definition: u32 value representing worst case latency in + microseconds required to enter the idle state. + The exit-latency-us duration may be guaranteed + only after entry-latency-us has passed. + +- exit-latency-us + Usage: Required + Value type: <prop-encoded-array> + Definition: u32 value representing worst case latency + in microseconds required to exit the idle state. + +- min-residency-us + Usage: Required + Value type: <prop-encoded-array> + Definition: u32 value representing minimum residency duration + in microseconds after which the idle state will yield + power benefits after overcoming the overhead in entering +i the idle state. diff --git a/Documentation/devicetree/bindings/power/pd-samsung.txt b/Documentation/devicetree/bindings/power/pd-samsung.txt index 4e947372a693..549f7dee9b9d 100644 --- a/Documentation/devicetree/bindings/power/pd-samsung.txt +++ b/Documentation/devicetree/bindings/power/pd-samsung.txt @@ -6,12 +6,15 @@ to gate power to one or more peripherals on the processor. Required Properties: - compatible: should be one of the following. * samsung,exynos4210-pd - for exynos4210 type power domain. + * samsung,exynos5433-pd - for exynos5433 type power domain. - reg: physical base address of the controller and length of memory mapped region. - #power-domain-cells: number of cells in power domain specifier; must be 0. Optional Properties: +- label: Human readable string with domain name. Will be visible in userspace + to let user to distinguish between multiple domains in SoC. - clocks: List of clock handles. The parent clocks of the input clocks to the devices in this power domain are set to oscclk before power gating and restored back after powering on a domain. This is required for @@ -20,7 +23,7 @@ Optional Properties: - clock-names: The following clocks can be specified: - oscclk: Oscillator clock. - clkN: Input clocks to the devices in this power domain. These clocks - will be reparented to oscclk before swithing power domain off. + will be reparented to oscclk before switching power domain off. Their original parent will be brought back after turning on the domain. Maximum of 4 clocks (N = 0 to 3) are supported. - asbN: Clocks required by asynchronous bridges (ASB) present in @@ -38,6 +41,7 @@ Example: compatible = "samsung,exynos4210-pd"; reg = <0x10023C00 0x10>; #power-domain-cells = <0>; + label = "LCD0"; }; mfc_pd: power-domain@10044060 { @@ -46,6 +50,7 @@ Example: clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MOUT_USER_ACLK333>; clock-names = "oscclk", "clk0"; #power-domain-cells = <0>; + label = "MFC"; }; See Documentation/devicetree/bindings/power/power_domain.txt for description diff --git a/Documentation/devicetree/bindings/power/power_domain.txt b/Documentation/devicetree/bindings/power/power_domain.txt index 025b5e7df61c..723e1ad937da 100644 --- a/Documentation/devicetree/bindings/power/power_domain.txt +++ b/Documentation/devicetree/bindings/power/power_domain.txt @@ -29,6 +29,15 @@ Optional properties: specified by this binding. More details about power domain specifier are available in the next section. +- domain-idle-states : A phandle of an idle-state that shall be soaked into a + generic domain power state. The idle state definitions are + compatible with domain-idle-state specified in [1]. + The domain-idle-state property reflects the idle state of this PM domain and + not the idle states of the devices or sub-domains in the PM domain. Devices + and sub-domains have their own idle-states independent of the parent + domain's idle states. In the absence of this property, the domain would be + considered as capable of being powered-on or powered-off. + Example: power: power-controller@12340000 { @@ -59,6 +68,38 @@ The nodes above define two power controllers: 'parent' and 'child'. Domains created by the 'child' power controller are subdomains of '0' power domain provided by the 'parent' power controller. +Example 3: + parent: power-controller@12340000 { + compatible = "foo,power-controller"; + reg = <0x12340000 0x1000>; + #power-domain-cells = <0>; + domain-idle-states = <&DOMAIN_RET>, <&DOMAIN_PWR_DN>; + }; + + child: power-controller@12341000 { + compatible = "foo,power-controller"; + reg = <0x12341000 0x1000>; + power-domains = <&parent 0>; + #power-domain-cells = <0>; + domain-idle-states = <&DOMAIN_PWR_DN>; + }; + + DOMAIN_RET: state@0 { + compatible = "domain-idle-state"; + reg = <0x0>; + entry-latency-us = <1000>; + exit-latency-us = <2000>; + min-residency-us = <10000>; + }; + + DOMAIN_PWR_DN: state@1 { + compatible = "domain-idle-state"; + reg = <0x1>; + entry-latency-us = <5000>; + exit-latency-us = <8000>; + min-residency-us = <7000>; + }; + ==PM domain consumers== Required properties: @@ -76,3 +117,5 @@ Example: The node above defines a typical PM domain consumer device, which is located inside a PM domain with index 0 of a power controller represented by a node with the label "power". + +[1]. Documentation/devicetree/bindings/power/domain-idle-state.txt diff --git a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt index 0725fb37a973..d91715bc8d52 100644 --- a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt +++ b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt @@ -1,12 +1,14 @@ -DT bindings for the Renesas R-Car System Controller +DT bindings for the Renesas R-Car (RZ/G) System Controller == System Controller Node == -The R-Car System Controller provides power management for the CPU cores and -various coprocessors. +The R-Car (RZ/G) System Controller provides power management for the CPU cores +and various coprocessors. Required properties: - compatible: Must contain exactly one of the following: + - "renesas,r8a7743-sysc" (RZ/G1M) + - "renesas,r8a7745-sysc" (RZ/G1E) - "renesas,r8a7779-sysc" (R-Car H1) - "renesas,r8a7790-sysc" (R-Car H2) - "renesas,r8a7791-sysc" (R-Car M2-W) diff --git a/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt b/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt index d4eab9227ea4..e62d53d844cc 100644 --- a/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt +++ b/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt @@ -2,12 +2,12 @@ Driver a GPIO line that can be used to turn the power off. The driver supports both level triggered and edge triggered power off. At driver load time, the driver will request the given gpio line and -install a pm_power_off handler. If the optional properties 'input' is -not found, the GPIO line will be driven in the inactive +install a handler to power off the system. If the optional properties +'input' is not found, the GPIO line will be driven in the inactive state. Otherwise its configured as an input. -When the pm_power_off is called, the gpio is configured as an output, -and drive active, so triggering a level triggered power off +When the power-off handler is called, the gpio is configured as an +output, and drive active, so triggering a level triggered power off condition. This will also cause an inactive->active edge condition, so triggering positive edge triggered power off. After a delay of 100ms, the GPIO is set to inactive, thus causing an active->inactive edge, @@ -24,7 +24,7 @@ Required properties: Optional properties: - input : Initially configure the GPIO line as an input. Only reconfigure - it to an output when the pm_power_off function is called. If this optional + it to an output when the power-off handler is called. If this optional property is not specified, the GPIO is initialized as an output in its inactive state. diff --git a/Documentation/devicetree/bindings/power/reset/qnap-poweroff.txt b/Documentation/devicetree/bindings/power/reset/qnap-poweroff.txt index af25e77c0e0c..c363d7173129 100644 --- a/Documentation/devicetree/bindings/power/reset/qnap-poweroff.txt +++ b/Documentation/devicetree/bindings/power/reset/qnap-poweroff.txt @@ -3,8 +3,7 @@ QNAP NAS devices have a microcontroller controlling the main power supply. This microcontroller is connected to UART1 of the Kirkwood and Orion5x SoCs. Sending the character 'A', at 19200 baud, tells the -microcontroller to turn the power off. This driver adds a handler to -pm_power_off which is called to turn the power off. +microcontroller to turn the power off. Synology NAS devices use a similar scheme, but a different baud rate, 9600, and a different character, '1'. diff --git a/Documentation/devicetree/bindings/power/supply/axp20x_ac_power.txt b/Documentation/devicetree/bindings/power/supply/axp20x_ac_power.txt new file mode 100644 index 000000000000..826e8a879121 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/axp20x_ac_power.txt @@ -0,0 +1,22 @@ +AXP20X and AXP22X PMICs' AC power supply + +Required Properties: + - compatible: One of: + "x-powers,axp202-ac-power-supply" + "x-powers,axp221-ac-power-supply" + +This node is a subnode of the axp20x PMIC. + +The AXP20X can read the current current and voltage supplied by AC by +reading ADC channels from the AXP20X ADC. + +The AXP22X is only able to tell if an AC power supply is present and +usable. + +Example: + +&axp209 { + ac_power_supply: ac-power-supply { + compatible = "x-powers,axp202-ac-power-supply"; + }; +}; diff --git a/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt b/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt index f1d7beec45bf..ba8d35f66cbe 100644 --- a/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt +++ b/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt @@ -3,6 +3,11 @@ AXP20x USB power supply Required Properties: -compatible: One of: "x-powers,axp202-usb-power-supply" "x-powers,axp221-usb-power-supply" + "x-powers,axp223-usb-power-supply" + +The AXP223 PMIC shares most of its behaviour with the AXP221 but has slight +variations such as the former being able to set the VBUS power supply max +current to 100mA, unlike the latter. This node is a subnode of the axp20x PMIC. diff --git a/Documentation/devicetree/bindings/power/supply/bq27xxx.txt b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt new file mode 100644 index 000000000000..b0c95ef63e68 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt @@ -0,0 +1,36 @@ +Binding for TI BQ27XXX fuel gauge family + +Required properties: +- compatible: Should contain one of the following: + * "ti,bq27200" - BQ27200 + * "ti,bq27210" - BQ27210 + * "ti,bq27500" - deprecated, use revision specific property below + * "ti,bq27510" - deprecated, use revision specific property below + * "ti,bq27520" - deprecated, use revision specific property below + * "ti,bq27500-1" - BQ27500/1 + * "ti,bq27510g1" - BQ27510-g1 + * "ti,bq27510g2" - BQ27510-g2 + * "ti,bq27510g3" - BQ27510-g3 + * "ti,bq27520g1" - BQ27520-g1 + * "ti,bq27520g2" - BQ27520-g2 + * "ti,bq27520g3" - BQ27520-g3 + * "ti,bq27520g4" - BQ27520-g4 + * "ti,bq27530" - BQ27530 + * "ti,bq27531" - BQ27531 + * "ti,bq27541" - BQ27541 + * "ti,bq27542" - BQ27542 + * "ti,bq27546" - BQ27546 + * "ti,bq27742" - BQ27742 + * "ti,bq27545" - BQ27545 + * "ti,bq27421" - BQ27421 + * "ti,bq27425" - BQ27425 + * "ti,bq27441" - BQ27441 + * "ti,bq27621" - BQ27621 +- reg: integer, i2c address of the device. + +Example: + +bq27510g3 { + compatible = "ti,bq27510g3"; + reg = <0x55>; +}; diff --git a/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt b/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt index 65b88fac854b..06f8a5ddb68e 100644 --- a/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt +++ b/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt @@ -105,6 +105,22 @@ PROPERTIES regulation must be done externally to fully comply with the JEITA safety guidelines if this flag is set. +- usb_otg_in-supply: + Usage: optional + Value type: <phandle> + Description: Reference to the regulator supplying power to the USB_OTG_IN + pin. + +child nodes: +- otg-vbus: + Usage: optional + Description: This node defines a regulator used to control the direction + of VBUS voltage - specifically: whether to supply voltage + to VBUS for host mode operation of the OTG port, or allow + input voltage from external VBUS for charging. In the + hardware, the supply for this regulator comes from + usb_otg_in-supply. + EXAMPLE charger@1000 { compatible = "qcom,pm8941-charger"; @@ -128,4 +144,7 @@ charger@1000 { qcom,fast-charge-current-limit = <1000000>; qcom,dc-charge-current-limit = <1000000>; + usb_otg_in-supply = <&pm8941_5vs1>; + + otg-vbus {}; }; diff --git a/Documentation/devicetree/bindings/power/supply/sbs_sbs-charger.txt b/Documentation/devicetree/bindings/power/supply/sbs_sbs-charger.txt new file mode 100644 index 000000000000..a3719623a94f --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/sbs_sbs-charger.txt @@ -0,0 +1,23 @@ +SBS sbs-charger +~~~~~~~~~~ + +Required properties: + - compatible: "<vendor>,<part-number>", "sbs,sbs-charger" as fallback. The part + number compatible string might be used in order to take care of vendor + specific registers. + +Optional properties: +- interrupt-parent: Should be the phandle for the interrupt controller. Use in + conjunction with "interrupts". +- interrupts: Interrupt mapping for GPIO IRQ. Use in conjunction with + "interrupt-parent". If an interrupt is not provided the driver will switch + automatically to polling. + +Example: + + ltc4100@9 { + compatible = "lltc,ltc4100", "sbs,sbs-charger"; + reg = <0x9>; + interrupt-parent = <&gpio6>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt b/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt index 3bf55757ceec..de45e1a2a4d9 100644 --- a/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt +++ b/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt @@ -8,8 +8,10 @@ Optional properties : - interrupts : Specify the interrupt to be used to trigger when the AC adapter is either plugged in or removed. - ti,ac-detect-gpios : This GPIO is optionally used to read the AC adapter - presence. This is a Host GPIO that is configured as an input and - connected to the bq24735. + status. This is a Host GPIO that is configured as an input and connected + to the ACOK pin on the bq24735. Note: for backwards compatibility reasons, + the GPIO must be active on AC adapter absence despite ACOK being active + (high) on AC adapter presence. - ti,charge-current : Used to control and set the charging current. This value must be between 128mA and 8.128A with a 64mA step resolution. The POR value is 0x0000h. This number is in mA (e.g. 8192), see spec for more information @@ -25,6 +27,8 @@ Optional properties : - ti,external-control : Indicates that the charger is configured externally and that the host should not attempt to enable/disable charging or set the charge voltage/current. + - poll-interval : In case 'interrupts' is not specified, poll AC adapter + presence with this interval (milliseconds). Example: diff --git a/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt b/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt index 98d131acee95..a11072c5a866 100644 --- a/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt +++ b/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt @@ -2,11 +2,16 @@ TPS65217 Charger Required Properties: -compatible: "ti,tps65217-charger" +-interrupts: TPS65217 interrupt numbers for the AC and USB charger input change. + Should be <0> for the USB charger and <1> for the AC adapter. +-interrupt-names: Should be "USB" and "AC" This node is a subnode of the tps65217 PMIC. Example: tps65217-charger { - compatible = "ti,tps65090-charger"; + compatible = "ti,tps65217-charger"; + interrupts = <0>, <1>; + interrupt-names = "USB", "AC"; }; diff --git a/Documentation/devicetree/bindings/power_supply/maxim,max14656.txt b/Documentation/devicetree/bindings/power_supply/maxim,max14656.txt new file mode 100644 index 000000000000..e03e85ae6572 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/maxim,max14656.txt @@ -0,0 +1,25 @@ +Maxim MAX14656 / AL32 USB Charger Detector + +Required properties : +- compatible : "maxim,max14656"; +- reg: i2c slave address +- interrupt-parent: the phandle for the interrupt controller +- interrupts: interrupt line + +Example: + +&i2c2 { + clock-frequency = <50000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + max14656@35 { + compatible = "maxim,max14656"; + reg = <0x35>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_charger_detect>; + interrupt-parent = <&gpio6>; + interrupts = <26 IRQ_TYPE_LEVEL_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/l2cache.txt b/Documentation/devicetree/bindings/powerpc/fsl/l2cache.txt index c41b2187eaa8..dc9bb3182525 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/l2cache.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/l2cache.txt @@ -5,8 +5,46 @@ The cache bindings explained below are ePAPR compliant Required Properties: -- compatible : Should include "fsl,chip-l2-cache-controller" and "cache" - where chip is the processor (bsc9132, npc8572 etc.) +- compatible : Should include one of the following: + "fsl,8540-l2-cache-controller" + "fsl,8541-l2-cache-controller" + "fsl,8544-l2-cache-controller" + "fsl,8548-l2-cache-controller" + "fsl,8555-l2-cache-controller" + "fsl,8568-l2-cache-controller" + "fsl,b4420-l2-cache-controller" + "fsl,b4860-l2-cache-controller" + "fsl,bsc9131-l2-cache-controller" + "fsl,bsc9132-l2-cache-controller" + "fsl,c293-l2-cache-controller" + "fsl,mpc8536-l2-cache-controller" + "fsl,mpc8540-l2-cache-controller" + "fsl,mpc8541-l2-cache-controller" + "fsl,mpc8544-l2-cache-controller" + "fsl,mpc8548-l2-cache-controller" + "fsl,mpc8555-l2-cache-controller" + "fsl,mpc8560-l2-cache-controller" + "fsl,mpc8568-l2-cache-controller" + "fsl,mpc8569-l2-cache-controller" + "fsl,mpc8572-l2-cache-controller" + "fsl,p1010-l2-cache-controller" + "fsl,p1011-l2-cache-controller" + "fsl,p1012-l2-cache-controller" + "fsl,p1013-l2-cache-controller" + "fsl,p1014-l2-cache-controller" + "fsl,p1015-l2-cache-controller" + "fsl,p1016-l2-cache-controller" + "fsl,p1020-l2-cache-controller" + "fsl,p1021-l2-cache-controller" + "fsl,p1022-l2-cache-controller" + "fsl,p1023-l2-cache-controller" + "fsl,p1024-l2-cache-controller" + "fsl,p1025-l2-cache-controller" + "fsl,p2010-l2-cache-controller" + "fsl,p2020-l2-cache-controller" + "fsl,t2080-l2-cache-controller" + "fsl,t4240-l2-cache-controller" + and "cache". - reg : Address and size of L2 cache controller registers - cache-size : Size of the entire L2 cache - interrupts : Error interrupt of L2 controller diff --git a/Documentation/devicetree/bindings/powerpc/opal/power-mgt.txt b/Documentation/devicetree/bindings/powerpc/opal/power-mgt.txt new file mode 100644 index 000000000000..9d619e955576 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/opal/power-mgt.txt @@ -0,0 +1,118 @@ +IBM Power-Management Bindings +============================= + +Linux running on baremetal POWER machines has access to the processor +idle states. The description of these idle states is exposed via the +node @power-mgt in the device-tree by the firmware. + +Definitions: +---------------- +Typically each idle state has the following associated properties: + +- name: The name of the idle state as defined by the firmware. + +- flags: indicating some aspects of this idle states such as the + extent of state-loss, whether timebase is stopped on this + idle states and so on. The flag bits are as follows: + +- exit-latency: The latency involved in transitioning the state of the + CPU from idle to running. + +- target-residency: The minimum time that the CPU needs to reside in + this idle state in order to accrue power-savings + benefit. + +Properties +---------------- +The following properties provide details about the idle states. These +properties are exposed as arrays. Each entry in the property array +provides the value of that property for the idle state associated with +the array index of that entry. + +If idle-states are defined, then the properties +"ibm,cpu-idle-state-names" and "ibm,cpu-idle-state-flags" are +required. The other properties are required unless mentioned +otherwise. The length of all the property arrays must be the same. + +- ibm,cpu-idle-state-names: + Array of strings containing the names of the idle states. + +- ibm,cpu-idle-state-flags: + Array of unsigned 32-bit values containing the values of the + flags associated with the the aforementioned idle-states. The + flag bits are as follows: + 0x00000001 /* Decrementer would stop */ + 0x00000002 /* Needs timebase restore */ + 0x00001000 /* Restore GPRs like nap */ + 0x00002000 /* Restore hypervisor resource from PACA pointer */ + 0x00004000 /* Program PORE to restore PACA pointer */ + 0x00010000 /* This is a nap state (POWER7,POWER8) */ + 0x00020000 /* This is a fast-sleep state (POWER8)*/ + 0x00040000 /* This is a winkle state (POWER8) */ + 0x00080000 /* This is a fast-sleep state which requires a */ + /* software workaround for restoring the */ + /* timebase (POWER8) */ + 0x00800000 /* This state uses SPR PMICR instruction */ + /* (POWER8)*/ + 0x00100000 /* This is a fast stop state (POWER9) */ + 0x00200000 /* This is a deep-stop state (POWER9) */ + +- ibm,cpu-idle-state-latencies-ns: + Array of unsigned 32-bit values containing the values of the + exit-latencies (in ns) for the idle states in + ibm,cpu-idle-state-names. + +- ibm,cpu-idle-state-residency-ns: + Array of unsigned 32-bit values containing the values of the + target-residency (in ns) for the idle states in + ibm,cpu-idle-state-names. On POWER8 this is an optional + property. If the property is absent, the target residency for + the "Nap", "FastSleep" are defined to 10000 and 300000000 + respectively by the kernel. On POWER9 this property is required. + +- ibm,cpu-idle-state-psscr: + Array of unsigned 64-bit values containing the values for the + PSSCR for each of the idle states in ibm,cpu-idle-state-names. + This property is required on POWER9 and absent on POWER8. + +- ibm,cpu-idle-state-psscr-mask: + Array of unsigned 64-bit values containing the masks + indicating which psscr fields are set in the corresponding + entries of ibm,cpu-idle-state-psscr. This property is + required on POWER9 and absent on POWER8. + + Whenever the firmware sets an entry in + ibm,cpu-idle-state-psscr-mask value to 0xf, it implies that + only the Requested Level (RL) field of the corresponding entry + in ibm,cpu-idle-state-psscr should be considered by the + kernel. For such idle states, the kernel would set the + remaining fields of the psscr to the following sane-default + values. + + - ESL and EC bits are to 1. So wakeup from any stop + state will be at vector 0x100. + + - MTL and PSLL are set to the maximum allowed value as + per the ISA, i.e. 15. + + - The Transition Rate, TR is set to the Maximum value + 3. + + For all the other values of the entry in + ibm,cpu-idle-state-psscr-mask, the kernel expects all the + psscr fields of the corresponding entry in + ibm,cpu-idle-state-psscr to be correctly set by the firmware. + +- ibm,cpu-idle-state-pmicr: + Array of unsigned 64-bit values containing the pmicr values + for the idle states in ibm,cpu-idle-state-names. This 64-bit + register value is to be set in pmicr for the corresponding + state if the flag indicates that pmicr SPR should be set. This + is an optional property on POWER8 and is absent on + POWER9. + +- ibm,cpu-idle-state-pmicr-mask: + Array of unsigned 64-bit values containing the mask indicating + which of the fields of the PMICR are set in the corresponding + entries in ibm,cpu-idle-state-pmicr. This is an optional + property on POWER8 and is absent on POWER9. diff --git a/Documentation/devicetree/bindings/pwm/imx-pwm.txt b/Documentation/devicetree/bindings/pwm/imx-pwm.txt index e00c2e9f484d..c61bdf8cd41b 100644 --- a/Documentation/devicetree/bindings/pwm/imx-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/imx-pwm.txt @@ -6,8 +6,8 @@ Required properties: - "fsl,imx1-pwm" for PWM compatible with the one integrated on i.MX1 - "fsl,imx27-pwm" for PWM compatible with the one integrated on i.MX27 - reg: physical base address and length of the controller's registers -- #pwm-cells: should be 2. See pwm.txt in this directory for a description of - the cells format. +- #pwm-cells: 2 for i.MX1 and 3 for i.MX27 and newer SoCs. See pwm.txt + in this directory for a description of the cells format. - clocks : Clock specifiers for both ipg and per clocks. - clock-names : Clock names should include both "ipg" and "per" See the clock consumer binding, @@ -17,7 +17,7 @@ See the clock consumer binding, Example: pwm1: pwm@53fb4000 { - #pwm-cells = <2>; + #pwm-cells = <3>; compatible = "fsl,imx53-pwm", "fsl,imx27-pwm"; reg = <0x53fb4000 0x4000>; clocks = <&clks IMX5_CLK_PWM1_IPG_GATE>, diff --git a/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt b/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt index fb6fb31bc4c4..cf573e85b11d 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt @@ -3,7 +3,7 @@ BCM2835 PWM controller (Raspberry Pi controller) Required properties: - compatible: should be "brcm,bcm2835-pwm" - reg: physical base address and length of the controller's registers -- clock: This clock defines the base clock frequency of the PWM hardware +- clocks: This clock defines the base clock frequency of the PWM hardware system, the period and the duty_cycle of the PWM signal is a multiple of the base period. - #pwm-cells: Should be 2. See pwm.txt in this directory for a description of diff --git a/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt b/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt new file mode 100644 index 000000000000..fa7849d67836 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt @@ -0,0 +1,21 @@ +Hisilicon PWM controller + +Required properties: +-compatible: should contain one SoC specific compatible string + The SoC specific strings supported including: + "hisilicon,hi3516cv300-pwm" + "hisilicon,hi3519v100-pwm" +- reg: physical base address and length of the controller's registers. +- clocks: phandle and clock specifier of the PWM reference clock. +- resets: phandle and reset specifier for the PWM controller reset. +- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of + the cells format. + +Example: + pwm: pwm@12130000 { + compatible = "hisilicon,hi3516cv300-pwm"; + reg = <0x12130000 0x10000>; + clocks = <&crg_ctrl HI3516CV300_PWM_CLK>; + resets = <&crg_ctrl 0x38 0>; + #pwm-cells = <3>; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-stm32.txt b/Documentation/devicetree/bindings/pwm/pwm-stm32.txt new file mode 100644 index 000000000000..6dd040363e5e --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-stm32.txt @@ -0,0 +1,35 @@ +STMicroelectronics STM32 Timers PWM bindings + +Must be a sub-node of an STM32 Timers device tree node. +See ../mfd/stm32-timers.txt for details about the parent node. + +Required parameters: +- compatible: Must be "st,stm32-pwm". +- pinctrl-names: Set to "default". +- pinctrl-0: List of phandles pointing to pin configuration nodes for PWM module. + For Pinctrl properties see ../pinctrl/pinctrl-bindings.txt + +Optional parameters: +- st,breakinput: One or two <index level filter> to describe break input configurations. + "index" indicates on which break input (0 or 1) the configuration + should be applied. + "level" gives the active level (0=low or 1=high) of the input signal + for this configuration. + "filter" gives the filtering value to be applied. + +Example: + timers@40010000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40010000 0x400>; + clocks = <&rcc 0 160>; + clock-names = "clk_int"; + + pwm { + compatible = "st,stm32-pwm"; + pinctrl-0 = <&pwm1_pins>; + pinctrl-names = "default"; + st,breakinput = <0 1 5>; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/anatop-regulator.txt b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt index 37c4ea076f88..1d58c8cfdbc0 100644 --- a/Documentation/devicetree/bindings/regulator/anatop-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt @@ -14,6 +14,7 @@ Optional properties: - anatop-delay-bit-shift: Bit shift for the step time register - anatop-delay-bit-width: Number of bits used in the step time register - vin-supply: The supply for this regulator +- anatop-enable-bit: Regulator enable bit offset Any property defined as part of the core regulator binding, defined in regulator.txt, can also be used. diff --git a/Documentation/devicetree/bindings/regulator/cpcap-regulator.txt b/Documentation/devicetree/bindings/regulator/cpcap-regulator.txt new file mode 100644 index 000000000000..675f4437ce92 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/cpcap-regulator.txt @@ -0,0 +1,34 @@ +Motorola CPCAP PMIC voltage regulators +------------------------------------ + +Requires node properties: +- "compatible" value one of: + "motorola,cpcap-regulator" + "motorola,mapphone-cpcap-regulator" + +Required regulator properties: +- "regulator-name" +- "regulator-enable-ramp-delay" +- "regulator-min-microvolt" +- "regulator-max-microvolt" + +Optional regulator properties: +- "regulator-boot-on" + +See Documentation/devicetree/bindings/regulator/regulator.txt +for more details about the regulator properties. + +Example: + +cpcap_regulator: regulator { + compatible = "motorola,cpcap-regulator"; + + cpcap_regulators: regulators { + sw5: SW5 { + regulator-min-microvolt = <5050000>; + regulator-max-microvolt = <5050000>; + regulator-enable-ramp-delay = <50000>; + regulator-boot-on; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/regulator/gpio-regulator.txt b/Documentation/devicetree/bindings/regulator/gpio-regulator.txt index e5cac1e0ca8a..dd1ed789728e 100644 --- a/Documentation/devicetree/bindings/regulator/gpio-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/gpio-regulator.txt @@ -13,7 +13,7 @@ Optional properties: - startup-delay-us : Startup time in microseconds. - enable-active-high : Polarity of GPIO is active high (default is low). - regulator-type : Specifies what is being regulated, must be either - "voltage" or "current", defaults to current. + "voltage" or "current", defaults to voltage. Any property defined as part of the core regulator binding defined in regulator.txt can also be used. diff --git a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt index 3aeba9f86ed8..bf85aa9ad6a7 100644 --- a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt @@ -59,7 +59,7 @@ Any property defined as part of the core regulator binding can also be used. Continuous Voltage With Enable GPIO Example: pwm_regulator { - compatible = "pwm-regulator; + compatible = "pwm-regulator"; pwms = <&pwm1 0 8448 0>; enable-gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>; regulator-min-microvolt = <1016000>; @@ -76,7 +76,7 @@ Continuous Voltage With Enable GPIO Example: Voltage Table Example: pwm_regulator { - compatible = "pwm-regulator; + compatible = "pwm-regulator"; pwms = <&pwm1 0 8448 0>; regulator-min-microvolt = <1016000>; regulator-max-microvolt = <1114000>; diff --git a/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt index 1f8d6f84b657..4e3dfb5b5f16 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt @@ -22,6 +22,7 @@ Regulator nodes are identified by their compatible: "qcom,rpm-pm8841-regulators" "qcom,rpm-pm8916-regulators" "qcom,rpm-pm8941-regulators" + "qcom,rpm-pm8994-regulators" "qcom,rpm-pma8084-regulators" - vdd_s1-supply: @@ -80,6 +81,56 @@ Regulator nodes are identified by their compatible: - vdd_s10-supply: - vdd_s11-supply: - vdd_s12-supply: +- vdd_l1-supply: +- vdd_l2_l26_l28-supply: +- vdd_l3_l11-supply: +- vdd_l4_l27_l31-supply: +- vdd_l5_l7-supply: +- vdd_l6_l12_l32-supply: +- vdd_l5_l7-supply: +- vdd_l8_l16_l30-supply: +- vdd_l9_l10_l18_l22-supply: +- vdd_l9_l10_l18_l22-supply: +- vdd_l3_l11-supply: +- vdd_l6_l12_l32-supply: +- vdd_l13_l19_l23_l24-supply: +- vdd_l14_l15-supply: +- vdd_l14_l15-supply: +- vdd_l8_l16_l30-supply: +- vdd_l17_l29-supply: +- vdd_l9_l10_l18_l22-supply: +- vdd_l13_l19_l23_l24-supply: +- vdd_l20_l21-supply: +- vdd_l20_l21-supply: +- vdd_l9_l10_l18_l22-supply: +- vdd_l13_l19_l23_l24-supply: +- vdd_l13_l19_l23_l24-supply: +- vdd_l25-supply: +- vdd_l2_l26_l28-supply: +- vdd_l4_l27_l31-supply: +- vdd_l2_l26_l28-supply: +- vdd_l17_l29-supply: +- vdd_l8_l16_l30-supply: +- vdd_l4_l27_l31-supply: +- vdd_l6_l12_l32-supply: +- vdd_lvs1_2-supply: + Usage: optional (pm8994 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_s4-supply: +- vdd_s5-supply: +- vdd_s6-supply: +- vdd_s7-supply: +- vdd_s8-supply: +- vdd_s9-supply: +- vdd_s10-supply: +- vdd_s11-supply: +- vdd_s12-supply: - vdd_l1_l11-supply: - vdd_l2_l3_l4_l27-supply: - vdd_l5_l7-supply: @@ -113,6 +164,11 @@ pm8941: l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3, 5vs1, 5vs2 +pm8994: + s1, s2, s3, s4, s5, s6, s7, s8, s9, s10, s11, s12, l1, l2, l3, l4, l5, + l6, l7, l8, l9, l10, l11, l12, l13, l14, l15, l16, l17, l18, l19, l20, + l21, l22, l23, l24, l25, l26, l27, l28, l29, l30, l31, l32, lvs1, lvs2 + pma8084: s1, s2, s3, s4, s5, s6, s7, s8, s9, s10, s11, s12, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14, l15, l16, l17, l18, l19, l20, diff --git a/Documentation/devicetree/bindings/regulator/tps65218.txt b/Documentation/devicetree/bindings/regulator/tps65218.txt index fccc1d24af58..02f0e9bbfbf8 100644 --- a/Documentation/devicetree/bindings/regulator/tps65218.txt +++ b/Documentation/devicetree/bindings/regulator/tps65218.txt @@ -1,23 +1,78 @@ TPS65218 family of regulators Required properties: -For tps65218 regulators/LDOs -- compatible: - - "ti,tps65218-dcdc1" for DCDC1 - - "ti,tps65218-dcdc2" for DCDC2 - - "ti,tps65218-dcdc3" for DCDC3 - - "ti,tps65218-dcdc4" for DCDC4 - - "ti,tps65218-dcdc5" for DCDC5 - - "ti,tps65218-dcdc6" for DCDC6 - - "ti,tps65218-ldo1" for LDO1 - -Optional properties: -- Any optional property defined in bindings/regulator/regulator.txt +- compatible: "ti,tps65218" +- reg: I2C slave address + +- List of regulators provided by this controller, must be named + after their hardware counterparts: dcdc[1-6] and ldo1 +- This is the list of child nodes that specify the regulator + initialization data for defined regulators. Not all regulators for the given + device need to be present. The definition for each of these nodes is defined + using the standard binding for regulators found at ./regulator.txt. + + The valid names for regulators are: + tps65217: regulator-dcdc1, regulator-dcdc2, regulator-dcdc3, regulator-dcdc4, + regulator-dcdc5, regulator-dcdc6, regulator-ldo1, regulator-ls3. + Each regulator is defined using the standard binding for regulators. Example: +tps65218: tps65218@24 { + reg = <0x24>; + compatible = "ti,tps65218"; + interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* NMIn */ + interrupt-controller; + #interrupt-cells = <2>; + + dcdc1: regulator-dcdc1 { + regulator-name = "vdd_core"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <1144000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc2: regulator-dcdc2 { + regulator-name = "vdd_mpu"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <1378000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3: regulator-dcdc3 { + regulator-name = "vdcdc3"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc5: regulator-dcdc5 { + regulator-name = "v1_0bat"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc6: regulator-dcdc6 { + regulator-name = "v1_8bat"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1: regulator-ldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; - xyz: regulator@0 { - compatible = "ti,tps65218-dcdc1"; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <3000000>; + ls3: regulator-ls3 { + regulator-min-microvolt = <100000>; + regulator-max-microvolt = <1000000>; }; +}; diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt b/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt new file mode 100644 index 000000000000..75ad7b8df0b1 --- /dev/null +++ b/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt @@ -0,0 +1,133 @@ +Qualcomm ADSP Peripheral Image Loader + +This document defines the binding for a component that loads and boots firmware +on the Qualcomm ADSP Hexagon core. + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,msm8974-adsp-pil" + "qcom,msm8996-adsp-pil" + "qcom,msm8996-slpi-pil" + +- interrupts-extended: + Usage: required + Value type: <prop-encoded-array> + Definition: must list the watchdog, fatal IRQs ready, handover and + stop-ack IRQs + +- interrupt-names: + Usage: required + Value type: <stringlist> + Definition: must be "wdog", "fatal", "ready", "handover", "stop-ack" + +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: reference to the xo clock and optionally aggre2 clock to be + held on behalf of the booting Hexagon core + +- clock-names: + Usage: required + Value type: <stringlist> + Definition: must be "xo" and optionally include "aggre2" + +- cx-supply: + Usage: required + Value type: <phandle> + Definition: reference to the regulator to be held on behalf of the + booting Hexagon core + +- px-supply: + Usage: required + Value type: <phandle> + Definition: reference to the px regulator to be held on behalf of the + booting Hexagon core + +- memory-region: + Usage: required + Value type: <phandle> + Definition: reference to the reserved-memory for the ADSP + +- qcom,smem-states: + Usage: required + Value type: <phandle> + Definition: reference to the smem state for requesting the ADSP to + shut down + +- qcom,smem-state-names: + Usage: required + Value type: <stringlist> + Definition: must be "stop" + + += SUBNODES +The adsp node may have an subnode named "smd-edge" that describes the SMD edge, +channels and devices related to the ADSP. See ../soc/qcom/qcom,smd.txt for +details on how to describe the SMD edge. + + += EXAMPLE +The following example describes the resources needed to boot control the +ADSP, as it is found on MSM8974 boards. + + adsp { + compatible = "qcom,msm8974-adsp-pil"; + + interrupts-extended = <&intc 0 162 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "wdog", + "fatal", + "ready", + "handover", + "stop-ack"; + + clocks = <&rpmcc RPM_CXO_CLK>; + clock-names = "xo"; + + cx-supply = <&pm8841_s2>; + + memory-region = <&adsp_region>; + + qcom,smem-states = <&adsp_smp2p_out 0>; + qcom,smem-state-names = "stop"; + + smd-edge { + interrupts = <0 156 IRQ_TYPE_EDGE_RISING>; + + qcom,ipc = <&apcs 8 8>; + qcom,smd-edge = <1>; + }; + }; + +The following example describes the resources needed to boot control the +SLPI, as it is found on MSM8996 boards. + + slpi { + compatible = "qcom,msm8996-slpi-pil"; + interrupts-extended = <&intc 0 390 IRQ_TYPE_EDGE_RISING>, + <&slpi_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, + <&slpi_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, + <&slpi_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, + <&slpi_smp2p_in 3 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "wdog", + "fatal", + "ready", + "handover", + "stop-ack"; + + clocks = <&rpmcc MSM8996_RPM_SMD_XO_CLK_SRC>, + <&rpmcc MSM8996_RPM_SMD_AGGR2_NOC_CLK>; + clock-names = "xo", "aggre2"; + + cx-supply = <&pm8994_l26>; + px-supply = <&pm8994_lvs2>; + + memory-region = <&slpi_region>; + qcom,smem-states = <&slpi_smp2p_out 0>; + qcom,smem-state-names = "stop"; + }; diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt index 57cb49ec55ca..92347fe6890e 100644 --- a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt +++ b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt @@ -7,7 +7,9 @@ on the Qualcomm Hexagon core. Usage: required Value type: <string> Definition: must be one of: - "qcom,q6v5-pil" + "qcom,q6v5-pil", + "qcom,msm8916-mss-pil", + "qcom,msm8974-mss-pil" - reg: Usage: required diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.txt b/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.txt index 0d2361ebe3d7..d420f84ddfb0 100644 --- a/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.txt +++ b/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.txt @@ -60,8 +60,8 @@ on the Qualcomm WCNSS core. see ../reserved-memory/reserved-memory.txt = SUBNODES -A single subnode of the WCNSS PIL describes the attached rf module and its -resource dependencies. +A required subnode of the WCNSS PIL is used to describe the attached rf module +and its resource dependencies. It is described by the following properties: - compatible: Usage: required @@ -90,6 +90,11 @@ resource dependencies. Definition: reference to the regulators to be held on behalf of the booting of the WCNSS core + +The wcnss node can also have an subnode named "smd-edge" that describes the SMD +edge, channels and devices related to the WCNSS. +See ../soc/qcom/qcom,smd.txt for details on how to describe the SMD edge. + = EXAMPLE The following example describes the resources needed to boot control the WCNSS, with attached WCN3680, as it is commonly found on MSM8974 boards. @@ -129,4 +134,25 @@ pronto@fb204000 { vddpa-supply = <&pm8941_l19>; vdddig-supply = <&pm8941_s3>; }; + + smd-edge { + interrupts = <0 142 1>; + + qcom,ipc = <&apcs 8 17>; + qcom,smd-edge = <6>; + qcom,remote-pid = <4>; + + label = "pronto"; + + wcnss { + compatible = "qcom,wcnss"; + qcom,smd-channels = "WCNSS_CTRL"; + + qcom,mmio = <&pronto>; + + bt { + compatible = "qcom,wcnss-bt"; + }; + }; + }; }; diff --git a/Documentation/devicetree/bindings/reserved-memory/ramoops.txt b/Documentation/devicetree/bindings/reserved-memory/ramoops.txt index e81f821a2135..0eba562fe5c6 100644 --- a/Documentation/devicetree/bindings/reserved-memory/ramoops.txt +++ b/Documentation/devicetree/bindings/reserved-memory/ramoops.txt @@ -46,3 +46,6 @@ Optional properties: (defaults to buffered mappings) - no-dump-oops: if present, only dump panics (defaults to panics and oops) + +- flags: if present, pass ramoops behavioral flags (defaults to 0, + see include/linux/pstore_ram.h RAMOOPS_FLAG_* for flag values). diff --git a/Documentation/devicetree/bindings/reset/hisilicon,hi3660-reset.txt b/Documentation/devicetree/bindings/reset/hisilicon,hi3660-reset.txt new file mode 100644 index 000000000000..2bf3344b2a02 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/hisilicon,hi3660-reset.txt @@ -0,0 +1,43 @@ +Hisilicon System Reset Controller +====================================== + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +The reset controller registers are part of the system-ctl block on +hi3660 SoC. + +Required properties: +- compatible: should be + "hisilicon,hi3660-reset" +- hisi,rst-syscon: phandle of the reset's syscon. +- #reset-cells : Specifies the number of cells needed to encode a + reset source. The type shall be a <u32> and the value shall be 2. + + Cell #1 : offset of the reset assert control + register from the syscon register base + offset + 4: deassert control register + offset + 8: status control register + Cell #2 : bit position of the reset in the reset control register + +Example: + iomcu: iomcu@ffd7e000 { + compatible = "hisilicon,hi3660-iomcu", "syscon"; + reg = <0x0 0xffd7e000 0x0 0x1000>; + }; + + iomcu_rst: iomcu_rst_controller { + compatible = "hisilicon,hi3660-reset"; + hisi,rst-syscon = <&iomcu>; + #reset-cells = <2>; + }; + +Specifying reset lines connected to IP modules +============================================== +example: + + i2c0: i2c@..... { + ... + resets = <&iomcu_rst 0x20 3>; /* offset: 0x20; bit: 3 */ + ... + }; diff --git a/Documentation/devicetree/bindings/reset/oxnas,reset.txt b/Documentation/devicetree/bindings/reset/oxnas,reset.txt index 6f06db930030..d27ccb5d04fc 100644 --- a/Documentation/devicetree/bindings/reset/oxnas,reset.txt +++ b/Documentation/devicetree/bindings/reset/oxnas,reset.txt @@ -5,45 +5,19 @@ Please also refer to reset.txt in this directory for common reset controller binding usage. Required properties: -- compatible: Should be "oxsemi,ox810se-reset" +- compatible: For OX810SE, should be "oxsemi,ox810se-reset" + For OX820, should be "oxsemi,ox820-reset" - #reset-cells: 1, see below Parent node should have the following properties : -- compatible: Should be "oxsemi,ox810se-sys-ctrl", "syscon", "simple-mfd" +- compatible: For OX810SE, should be : + "oxsemi,ox810se-sys-ctrl", "syscon", "simple-mfd" + For OX820, should be : + "oxsemi,ox820-sys-ctrl", "syscon", "simple-mfd" -For OX810SE, the indices are : - - 0 : ARM - - 1 : COPRO - - 2 : Reserved - - 3 : Reserved - - 4 : USBHS - - 5 : USBHSPHY - - 6 : MAC - - 7 : PCI - - 8 : DMA - - 9 : DPE - - 10 : DDR - - 11 : SATA - - 12 : SATA_LINK - - 13 : SATA_PHY - - 14 : Reserved - - 15 : NAND - - 16 : GPIO - - 17 : UART1 - - 18 : UART2 - - 19 : MISC - - 20 : I2S - - 21 : AHB_MON - - 22 : UART3 - - 23 : UART4 - - 24 : SGDMA - - 25 : Reserved - - 26 : Reserved - - 27 : Reserved - - 28 : Reserved - - 29 : Reserved - - 30 : Reserved - - 31 : BUS +Reset indices are in dt-bindings include files : +- For OX810SE: include/dt-bindings/reset/oxsemi,ox810se.h +- For OX820: include/dt-bindings/reset/oxsemi,ox820.h example: diff --git a/Documentation/devicetree/bindings/reset/renesas,rst.txt b/Documentation/devicetree/bindings/reset/renesas,rst.txt new file mode 100644 index 000000000000..fe5e0f37b3c9 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/renesas,rst.txt @@ -0,0 +1,37 @@ +DT bindings for the Renesas R-Car and RZ/G Reset Controllers + +The R-Car and RZ/G Reset Controllers provide reset control, and implement the +following functions: + - Latching of the levels on mode pins when PRESET# is negated, + - Mode monitoring register, + - Reset control of peripheral devices (on R-Car Gen1), + - Watchdog timer (on R-Car Gen1), + - Register-based reset control and boot address registers for the various CPU + cores (on R-Car Gen2 and Gen3, and on RZ/G). + + +Required properties: + - compatible: Should be + - "renesas,<soctype>-reset-wdt" for R-Car Gen1, + - "renesas,<soctype>-rst" for R-Car Gen2 and Gen3, and RZ/G + Examples with soctypes are: + - "renesas,r8a7743-rst" (RZ/G1M) + - "renesas,r8a7745-rst" (RZ/G1E) + - "renesas,r8a7778-reset-wdt" (R-Car M1A) + - "renesas,r8a7779-reset-wdt" (R-Car H1) + - "renesas,r8a7790-rst" (R-Car H2) + - "renesas,r8a7791-rst" (R-Car M2-W) + - "renesas,r8a7792-rst" (R-Car V2H + - "renesas,r8a7793-rst" (R-Car M2-N) + - "renesas,r8a7794-rst" (R-Car E2) + - "renesas,r8a7795-rst" (R-Car H3) + - "renesas,r8a7796-rst" (R-Car M3-W) + - reg: Address start and address range for the device. + + +Example: + + rst: reset-controller@e6160000 { + compatible = "renesas,r8a7795-rst"; + reg = <0 0xe6160000 0 0x0200>; + }; diff --git a/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt b/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt index 1cfd21d1dfa1..92527138bc93 100644 --- a/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt +++ b/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt @@ -16,15 +16,14 @@ Please refer to reset.txt in this directory for common reset controller binding usage. Required properties: -- compatible: Should be "st,<chip>-powerdown" - ex: "st,stih415-powerdown", "st,stih416-powerdown" +- compatible: Should be "st,stih407-powerdown" - #reset-cells: 1, see below example: powerdown: powerdown-controller { + compatible = "st,stih407-powerdown"; #reset-cells = <1>; - compatible = "st,stih415-powerdown"; }; @@ -37,11 +36,10 @@ index specifying which channel to use, as described in reset.txt example: - usb1: usb@fe200000 { - resets = <&powerdown STIH41X_USB1_POWERDOWN>; + st_dwc3: dwc3@8f94000 { + resets = <&powerdown STIH407_USB3_POWERDOWN>, }; Macro definitions for the supported reset channels can be found in: -include/dt-bindings/reset/stih415-resets.h -include/dt-bindings/reset/stih416-resets.h +include/dt-bindings/reset/stih407-resets.h diff --git a/Documentation/devicetree/bindings/reset/st,sti-softreset.txt b/Documentation/devicetree/bindings/reset/st,sti-softreset.txt index 891a2fd85ed6..a21658f18fe6 100644 --- a/Documentation/devicetree/bindings/reset/st,sti-softreset.txt +++ b/Documentation/devicetree/bindings/reset/st,sti-softreset.txt @@ -15,15 +15,14 @@ Please refer to reset.txt in this directory for common reset controller binding usage. Required properties: -- compatible: Should be "st,<chip>-softreset" example: - "st,stih415-softreset" or "st,stih416-softreset"; +- compatible: Should be st,stih407-softreset"; - #reset-cells: 1, see below example: softreset: softreset-controller { #reset-cells = <1>; - compatible = "st,stih415-softreset"; + compatible = "st,stih407-softreset"; }; @@ -42,5 +41,4 @@ example: Macro definitions for the supported reset channels can be found in: -include/dt-bindings/reset/stih415-resets.h -include/dt-bindings/reset/stih416-resets.h +include/dt-bindings/reset/stih407-resets.h diff --git a/Documentation/devicetree/bindings/reset/ti-syscon-reset.txt b/Documentation/devicetree/bindings/reset/ti-syscon-reset.txt index 164c7f34c451..c516d24959f2 100644 --- a/Documentation/devicetree/bindings/reset/ti-syscon-reset.txt +++ b/Documentation/devicetree/bindings/reset/ti-syscon-reset.txt @@ -63,7 +63,7 @@ Example: -------- The following example demonstrates a syscon node, the reset controller node using the syscon node, and a consumer (a DSP device) on the TI Keystone 2 -Edison SoC. +66AK2E SoC. / { soc { @@ -71,13 +71,13 @@ Edison SoC. compatible = "syscon", "simple-mfd"; reg = <0x02350000 0x1000>; - pscrst: psc-reset { + pscrst: reset-controller { compatible = "ti,k2e-pscrst", "ti,syscon-reset"; #reset-cells = <1>; ti,reset-bits = < - 0xa3c 8 0xa3c 8 0x83c 8 (ASSERT_SET|DEASSERT_CLEAR|STATUS_SET) /* 0: pcrst-dsp0 */ - 0xa40 5 0xa44 3 0 0 (ASSERT_SET|DEASSERT_CLEAR|STATUS_NONE) /* 1: pcrst-example */ + 0xa3c 8 0xa3c 8 0x83c 8 (ASSERT_CLEAR | DEASSERT_SET | STATUS_CLEAR) /* 0: dsp0 */ + 0xa40 5 0xa44 3 0 0 (ASSERT_SET | DEASSERT_CLEAR | STATUS_NONE) /* 1: example */ >; }; }; diff --git a/Documentation/devicetree/bindings/reset/uniphier-reset.txt b/Documentation/devicetree/bindings/reset/uniphier-reset.txt index 5020524cddeb..83ab0f599c40 100644 --- a/Documentation/devicetree/bindings/reset/uniphier-reset.txt +++ b/Documentation/devicetree/bindings/reset/uniphier-reset.txt @@ -6,14 +6,14 @@ System reset Required properties: - compatible: should be one of the following: - "socionext,uniphier-sld3-reset" - for sLD3 SoC. - "socionext,uniphier-ld4-reset" - for LD4 SoC. - "socionext,uniphier-pro4-reset" - for Pro4 SoC. - "socionext,uniphier-sld8-reset" - for sLD8 SoC. - "socionext,uniphier-pro5-reset" - for Pro5 SoC. - "socionext,uniphier-pxs2-reset" - for PXs2/LD6b SoC. - "socionext,uniphier-ld11-reset" - for LD11 SoC. - "socionext,uniphier-ld20-reset" - for LD20 SoC. + "socionext,uniphier-sld3-reset" - for sLD3 SoC + "socionext,uniphier-ld4-reset" - for LD4 SoC + "socionext,uniphier-pro4-reset" - for Pro4 SoC + "socionext,uniphier-sld8-reset" - for sLD8 SoC + "socionext,uniphier-pro5-reset" - for Pro5 SoC + "socionext,uniphier-pxs2-reset" - for PXs2/LD6b SoC + "socionext,uniphier-ld11-reset" - for LD11 SoC + "socionext,uniphier-ld20-reset" - for LD20 SoC - #reset-cells: should be 1. Example: @@ -37,14 +37,15 @@ Media I/O (MIO) reset, SD reset Required properties: - compatible: should be one of the following: - "socionext,uniphier-sld3-mio-reset" - for sLD3 SoC. - "socionext,uniphier-ld4-mio-reset" - for LD4 SoC. - "socionext,uniphier-pro4-mio-reset" - for Pro4 SoC. - "socionext,uniphier-sld8-mio-reset" - for sLD8 SoC. - "socionext,uniphier-pro5-sd-reset" - for Pro5 SoC. - "socionext,uniphier-pxs2-sd-reset" - for PXs2/LD6b SoC. - "socionext,uniphier-ld11-mio-reset" - for LD11 SoC. - "socionext,uniphier-ld20-sd-reset" - for LD20 SoC. + "socionext,uniphier-sld3-mio-reset" - for sLD3 SoC + "socionext,uniphier-ld4-mio-reset" - for LD4 SoC + "socionext,uniphier-pro4-mio-reset" - for Pro4 SoC + "socionext,uniphier-sld8-mio-reset" - for sLD8 SoC + "socionext,uniphier-pro5-sd-reset" - for Pro5 SoC + "socionext,uniphier-pxs2-sd-reset" - for PXs2/LD6b SoC + "socionext,uniphier-ld11-mio-reset" - for LD11 SoC (MIO) + "socionext,uniphier-ld11-sd-reset" - for LD11 SoC (SD) + "socionext,uniphier-ld20-sd-reset" - for LD20 SoC - #reset-cells: should be 1. Example: @@ -68,13 +69,13 @@ Peripheral reset Required properties: - compatible: should be one of the following: - "socionext,uniphier-ld4-peri-reset" - for LD4 SoC. - "socionext,uniphier-pro4-peri-reset" - for Pro4 SoC. - "socionext,uniphier-sld8-peri-reset" - for sLD8 SoC. - "socionext,uniphier-pro5-peri-reset" - for Pro5 SoC. - "socionext,uniphier-pxs2-peri-reset" - for PXs2/LD6b SoC. - "socionext,uniphier-ld11-peri-reset" - for LD11 SoC. - "socionext,uniphier-ld20-peri-reset" - for LD20 SoC. + "socionext,uniphier-ld4-peri-reset" - for LD4 SoC + "socionext,uniphier-pro4-peri-reset" - for Pro4 SoC + "socionext,uniphier-sld8-peri-reset" - for sLD8 SoC + "socionext,uniphier-pro5-peri-reset" - for Pro5 SoC + "socionext,uniphier-pxs2-peri-reset" - for PXs2/LD6b SoC + "socionext,uniphier-ld11-peri-reset" - for LD11 SoC + "socionext,uniphier-ld20-peri-reset" - for LD20 SoC - #reset-cells: should be 1. Example: diff --git a/Documentation/devicetree/bindings/reset/zte,zx2967-reset.txt b/Documentation/devicetree/bindings/reset/zte,zx2967-reset.txt new file mode 100644 index 000000000000..b015508f9780 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/zte,zx2967-reset.txt @@ -0,0 +1,20 @@ +ZTE zx2967 SoCs Reset Controller +======================================= + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: +- compatible: should be one of the following. + * zte,zx296718-reset +- reg: physical base address of the controller and length of memory mapped + region. +- #reset-cells: must be 1. + +example: + + reset: reset-controller@1461060 { + compatible = "zte,zx296718-reset"; + reg = <0x01461060 0x8>; + #reset-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/rng/omap_rng.txt b/Documentation/devicetree/bindings/rng/omap_rng.txt index 6a62acd86953..471477299ece 100644 --- a/Documentation/devicetree/bindings/rng/omap_rng.txt +++ b/Documentation/devicetree/bindings/rng/omap_rng.txt @@ -1,4 +1,4 @@ -OMAP SoC HWRNG Module +OMAP SoC and Inside-Secure HWRNG Module Required properties: @@ -6,11 +6,13 @@ Required properties: RNG versions: - "ti,omap2-rng" for OMAP2. - "ti,omap4-rng" for OMAP4, OMAP5 and AM33XX. + - "inside-secure,safexcel-eip76" for SoCs with EIP76 IP block Note that these two versions are incompatible. - ti,hwmods: Name of the hwmod associated with the RNG module - reg : Offset and length of the register set for the module - interrupts : the interrupt number for the RNG module. - Only used for "ti,omap4-rng". + Used for "ti,omap4-rng" and "inside-secure,safexcel-eip76" +- clocks: the trng clock source Example: /* AM335x */ @@ -20,3 +22,11 @@ rng: rng@48310000 { reg = <0x48310000 0x2000>; interrupts = <111>; }; + +/* SafeXcel IP-76 */ +trng: rng@f2760000 { + compatible = "inside-secure,safexcel-eip76"; + reg = <0xf2760000 0x7d>; + interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpm_syscon0 1 25>; +}; diff --git a/Documentation/devicetree/bindings/rtc/armada-380-rtc.txt b/Documentation/devicetree/bindings/rtc/armada-380-rtc.txt index 2eb9d4ee7dc0..c3c9a1226f9a 100644 --- a/Documentation/devicetree/bindings/rtc/armada-380-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/armada-380-rtc.txt @@ -1,9 +1,11 @@ -* Real Time Clock of the Armada 38x SoCs +* Real Time Clock of the Armada 38x/7K/8K SoCs -RTC controller for the Armada 38x SoCs +RTC controller for the Armada 38x, 7K and 8K SoCs Required properties: -- compatible : Should be "marvell,armada-380-rtc" +- compatible : Should be one of the following: + "marvell,armada-380-rtc" for Armada 38x SoC + "marvell,armada-8k-rtc" for Aramda 7K/8K SoCs - reg: a list of base address and size pairs, one for each entry in reg-names - reg names: should contain: diff --git a/Documentation/devicetree/bindings/rtc/cortina,gemini.txt b/Documentation/devicetree/bindings/rtc/cortina,gemini.txt new file mode 100644 index 000000000000..4ce4e794ddbb --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/cortina,gemini.txt @@ -0,0 +1,14 @@ +* Cortina Systems Gemini RTC + +Gemini SoC real-time clock. + +Required properties: +- compatible : Should be "cortina,gemini-rtc" + +Examples: + +rtc@45000000 { + compatible = "cortina,gemini-rtc"; + reg = <0x45000000 0x100>; + interrupts = <17 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/rtc/epson,rtc7301.txt b/Documentation/devicetree/bindings/rtc/epson,rtc7301.txt new file mode 100644 index 000000000000..5f9df3f1467c --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/epson,rtc7301.txt @@ -0,0 +1,16 @@ +EPSON TOYOCOM RTC-7301SF/DG + +Required properties: + +- compatible: Should be "epson,rtc7301sf" or "epson,rtc7301dg" +- reg: Specifies base physical address and size of the registers. +- interrupts: A single interrupt specifier. + +Example: + +rtc: rtc@44a00000 { + compatible = "epson,rtc7301dg"; + reg = <0x44a00000 0x10000>; + interrupt-parent = <&axi_intc_0>; + interrupts = <3 2>; +}; diff --git a/Documentation/devicetree/bindings/rtc/imxdi-rtc.txt b/Documentation/devicetree/bindings/rtc/imxdi-rtc.txt index c9d80d7da141..323cf26374cb 100644 --- a/Documentation/devicetree/bindings/rtc/imxdi-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/imxdi-rtc.txt @@ -8,10 +8,13 @@ Required properties: region. - interrupts: rtc alarm interrupt +Optional properties: +- interrupts: dryice security violation interrupt + Example: rtc@80056000 { compatible = "fsl,imx53-rtc", "fsl,imx25-rtc"; reg = <0x80056000 2000>; - interrupts = <29>; + interrupts = <29 56>; }; diff --git a/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt new file mode 100644 index 000000000000..41c7ae18fd7b --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt @@ -0,0 +1,37 @@ +JZ4740 and similar SoCs real-time clock driver + +Required properties: + +- compatible: One of: + - "ingenic,jz4740-rtc" - for use with the JZ4740 SoC + - "ingenic,jz4780-rtc" - for use with the JZ4780 SoC +- reg: Address range of rtc register set +- interrupts: IRQ number for the alarm interrupt +- clocks: phandle to the "rtc" clock +- clock-names: must be "rtc" + +Optional properties: +- system-power-controller: To use this component as the + system power controller +- reset-pin-assert-time-ms: Reset pin low-level assertion + time after wakeup (default 60ms; range 0-125ms if RTC clock + at 32 kHz) +- min-wakeup-pin-assert-time-ms: Minimum wakeup pin assertion + time (default 100ms; range 0-2s if RTC clock at 32 kHz) + +Example: + +rtc@10003000 { + compatible = "ingenic,jz4740-rtc"; + reg = <0x10003000 0x40>; + + interrupt-parent = <&intc>; + interrupts = <32>; + + clocks = <&rtc_clock>; + clock-names = "rtc"; + + system-power-controller; + reset-pin-assert-time-ms = <60>; + min-wakeup-pin-assert-time-ms = <100>; +}; diff --git a/Documentation/devicetree/bindings/rtc/maxim,ds3231.txt b/Documentation/devicetree/bindings/rtc/maxim,ds3231.txt index ddef330d2709..85be53a42180 100644 --- a/Documentation/devicetree/bindings/rtc/maxim,ds3231.txt +++ b/Documentation/devicetree/bindings/rtc/maxim,ds3231.txt @@ -1,7 +1,8 @@ * Maxim DS3231 Real Time Clock Required properties: -see: Documentation/devicetree/bindings/i2c/trivial-devices.txt +- compatible: Should contain "maxim,ds3231". +- reg: I2C address for chip. Optional property: - #clock-cells: Should be 1. diff --git a/Documentation/devicetree/bindings/rtc/pcf8563.txt b/Documentation/devicetree/bindings/rtc/pcf8563.txt index 72f6d2c9665e..36984acbb383 100644 --- a/Documentation/devicetree/bindings/rtc/pcf8563.txt +++ b/Documentation/devicetree/bindings/rtc/pcf8563.txt @@ -3,7 +3,8 @@ Philips PCF8563/Epson RTC8564 Real Time Clock Required properties: -see: Documentation/devicetree/bindings/i2c/trivial-devices.txt +- compatible: Should contain "nxp,pcf8563". +- reg: I2C address for chip. Optional property: - #clock-cells: Should be 0. diff --git a/Documentation/devicetree/bindings/rtc/st,stm32-rtc.txt b/Documentation/devicetree/bindings/rtc/st,stm32-rtc.txt new file mode 100644 index 000000000000..e2837b951237 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/st,stm32-rtc.txt @@ -0,0 +1,27 @@ +STM32 Real Time Clock + +Required properties: +- compatible: "st,stm32-rtc". +- reg: address range of rtc register set. +- clocks: reference to the clock entry ck_rtc. +- interrupt-parent: phandle for the interrupt controller. +- interrupts: rtc alarm interrupt. +- st,syscfg: phandle for pwrcfg, mandatory to disable/enable backup domain + (RTC registers) write protection. + +Optional properties (to override default ck_rtc parent clock): +- assigned-clocks: reference to the ck_rtc clock entry. +- assigned-clock-parents: phandle of the new parent clock of ck_rtc. + +Example: + + rtc: rtc@40002800 { + compatible = "st,stm32-rtc"; + reg = <0x40002800 0x400>; + clocks = <&rcc 1 CLK_RTC>; + assigned-clocks = <&rcc 1 CLK_RTC>; + assigned-clock-parents = <&rcc 1 CLK_LSE>; + interrupt-parent = <&exti>; + interrupts = <17 1>; + st,syscfg = <&pwrcfg>; + }; diff --git a/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt b/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt index f007e428a1ab..945934918b71 100644 --- a/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt @@ -8,10 +8,20 @@ Required properties: memory mapped region. - interrupts : IRQ lines for the RTC alarm 0 and alarm 1, in that order. +Required properties for new device trees +- clocks : phandle to the 32kHz external oscillator +- clock-output-names : name of the LOSC clock created +- #clock-cells : must be equals to 1. The RTC provides two clocks: the + LOSC and its external output, with index 0 and 1 + respectively. + Example: rtc: rtc@01f00000 { compatible = "allwinner,sun6i-a31-rtc"; reg = <0x01f00000 0x54>; interrupts = <0 40 4>, <0 41 4>; + clock-output-names = "osc32k"; + clocks = <&ext_osc32k>; + #clock-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/rtc/twl-rtc.txt b/Documentation/devicetree/bindings/rtc/twl-rtc.txt index 596e0c97be7a..8f9a94f2f896 100644 --- a/Documentation/devicetree/bindings/rtc/twl-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/twl-rtc.txt @@ -1,12 +1,11 @@ -* TI twl RTC - -The TWL family (twl4030/6030) contains a RTC. +* Texas Instruments TWL4030/6030 RTC Required properties: -- compatible : Should be twl4030-rtc - -Examples: - -rtc@0 { - compatible = "ti,twl4030-rtc"; -}; +- compatible : Should be "ti,twl4030-rtc" +- interrupts : Should be the interrupt number. + +Example: + rtc { + compatible = "ti,twl4030-rtc"; + interrupts = <11>; + }; diff --git a/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt b/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt index bf2411f366e5..2a42a323fa1a 100644 --- a/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt +++ b/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt @@ -6,6 +6,7 @@ Main node required properties: - compatible : value should be as follows: (a) "hisilicon,hip05-sas-v1" for v1 hw in hip05 chipset (b) "hisilicon,hip06-sas-v2" for v2 hw in hip06 chipset + (c) "hisilicon,hip07-sas-v2" for v2 hw in hip07 chipset - sas-addr : array of 8 bytes for host SAS address - reg : Address and length of the SAS register - hisilicon,sas-syscon: phandle of syscon used for sas control diff --git a/Documentation/devicetree/bindings/security/tpm/ibmvtpm.txt b/Documentation/devicetree/bindings/security/tpm/ibmvtpm.txt new file mode 100644 index 000000000000..d89f99971368 --- /dev/null +++ b/Documentation/devicetree/bindings/security/tpm/ibmvtpm.txt @@ -0,0 +1,41 @@ +* Device Tree Bindings for IBM Virtual Trusted Platform Module(vtpm) + +Required properties: + +- compatible : property name that conveys the platform architecture + identifiers, as 'IBM,vtpm' +- device_type : specifies type of virtual device +- interrupts : property specifying the interrupt source number and + sense code associated with this virtual I/O Adapters +- ibm,my-drc-index : integer index for the connector between the device + and its parent - present only if Dynamic + Reconfiguration(DR) Connector is enabled +- ibm,#dma-address-cells: specifies the number of cells that are used to + encode the physical address field of dma-window + properties +- ibm,#dma-size-cells : specifies the number of cells that are used to + encode the size field of dma-window properties +- ibm,my-dma-window : specifies DMA window associated with this virtual + IOA +- ibm,loc-code : specifies the unique and persistent location code + associated with this virtual I/O Adapters +- linux,sml-base : 64-bit base address of the reserved memory allocated + for the firmware event log +- linux,sml-size : size of the memory allocated for the firmware event log + +Example (IBM Virtual Trusted Platform Module) +--------------------------------------------- + + vtpm@30000003 { + ibm,#dma-size-cells = <0x2>; + compatible = "IBM,vtpm"; + device_type = "IBM,vtpm"; + ibm,my-drc-index = <0x30000003>; + ibm,#dma-address-cells = <0x2>; + linux,sml-base = <0xc60e 0x0>; + interrupts = <0xa0003 0x0>; + ibm,my-dma-window = <0x10000003 0x0 0x0 0x0 0x10000000>; + ibm,loc-code = "U8286.41A.10082DV-V3-C3"; + reg = <0x30000003>; + linux,sml-size = <0xbce10200>; + }; diff --git a/Documentation/devicetree/bindings/security/tpm/tpm-i2c.txt b/Documentation/devicetree/bindings/security/tpm/tpm-i2c.txt new file mode 100644 index 000000000000..8cb638b7e89c --- /dev/null +++ b/Documentation/devicetree/bindings/security/tpm/tpm-i2c.txt @@ -0,0 +1,21 @@ +* Device Tree Bindings for I2C based Trusted Platform Module(TPM) + +Required properties: + +- compatible : 'manufacturer,model', eg. nuvoton,npct650 +- label : human readable string describing the device, eg. "tpm" +- linux,sml-base : 64-bit base address of the reserved memory allocated for + the firmware event log +- linux,sml-size : size of the memory allocated for the firmware event log + +Example (for OpenPower Systems with Nuvoton TPM 2.0 on I2C) +---------------------------------------------------------- + +tpm@57 { + reg = <0x57>; + label = "tpm"; + compatible = "nuvoton,npct650", "nuvoton,npct601"; + linux,sml-base = <0x7f 0xfd450000>; + linux,sml-size = <0x10000>; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/security/tpm/tpm_tis_mmio.txt b/Documentation/devicetree/bindings/security/tpm/tpm_tis_mmio.txt new file mode 100644 index 000000000000..41d740545189 --- /dev/null +++ b/Documentation/devicetree/bindings/security/tpm/tpm_tis_mmio.txt @@ -0,0 +1,25 @@ +Trusted Computing Group MMIO Trusted Platform Module + +The TCG defines multi vendor standard for accessing a TPM chip, this +is the standard protocol defined to access the TPM via MMIO. Typically +this interface will be implemented over Intel's LPC bus. + +Refer to the 'TCG PC Client Specific TPM Interface Specification (TIS)' TCG +publication for the specification. + +Required properties: + +- compatible: should contain a string below for the chip, followed by + "tcg,tpm-tis-mmio". Valid chip strings are: + * "atmel,at97sc3204" +- reg: The location of the MMIO registers, should be at least 0x5000 bytes +- interrupt-parent/interrupts: An optional interrupt indicating command completion. + +Example: + + tpm_tis@90000 { + compatible = "atmel,at97sc3204", "tcg,tpm-tis-mmio"; + reg = <0x90000 0x5000>; + interrupt-parent = <&EIC0>; + interrupts = <1 2>; + }; diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt index f86bb06c39e9..10276a46ecef 100644 --- a/Documentation/devicetree/bindings/serial/8250.txt +++ b/Documentation/devicetree/bindings/serial/8250.txt @@ -19,6 +19,7 @@ Required properties: - "altr,16550-FIFO128" - "fsl,16550-FIFO64" - "fsl,ns16550" + - "ti,da830-uart" - "serial" if the port type is unknown. - reg : offset and length of the register set for the device. - interrupts : should contain uart interrupt. diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt index 1e82802d8e32..574c3a2c77d5 100644 --- a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt +++ b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt @@ -6,11 +6,13 @@ Required properties: - interrupts : Should contain uart interrupt Optional properties: -- uart-has-rtscts : Indicate the uart has rts and cts - fsl,irda-mode : Indicate the uart supports irda mode - fsl,dte-mode : Indicate the uart works in DTE mode. The uart works in DCE mode by default. +Please check Documentation/devicetree/bindings/serial/serial.txt +for the complete list of generic properties. + Note: Each uart controller should have an alias correctly numbered in "aliases" node. diff --git a/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt index 845850caf088..c93a2d1c1a65 100644 --- a/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt +++ b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt @@ -10,7 +10,7 @@ Required properties: See ../reset/reset.txt for details. - reset-names : Must include the following entries: - serial -- dmas : Must contain an entry for each entry in clock-names. +- dmas : Must contain an entry for each entry in dma-names. See ../dma/dma.txt for details. - dma-names : Must include the following entries: - rx diff --git a/Documentation/devicetree/bindings/serial/serial.txt b/Documentation/devicetree/bindings/serial/serial.txt index fd970f76a7b8..b542a0ecf06e 100644 --- a/Documentation/devicetree/bindings/serial/serial.txt +++ b/Documentation/devicetree/bindings/serial/serial.txt @@ -23,7 +23,8 @@ Optional properties: they are available for use (wired and enabled by pinmux configuration). This depends on both the UART hardware and the board wiring. Note that this property is mutually-exclusive with "cts-gpios" and - "rts-gpios" above. + "rts-gpios" above, unless support is provided to switch between modes + dynamically. Examples: diff --git a/Documentation/devicetree/bindings/serial/slave-device.txt b/Documentation/devicetree/bindings/serial/slave-device.txt new file mode 100644 index 000000000000..f66037928f5f --- /dev/null +++ b/Documentation/devicetree/bindings/serial/slave-device.txt @@ -0,0 +1,36 @@ +Serial Slave Device DT binding + +This documents the binding structure and common properties for serial +attached devices. Common examples include Bluetooth, WiFi, NFC and GPS +devices. + +Serial attached devices shall be a child node of the host UART device the +slave device is attached to. It is expected that the attached device is +the only child node of the UART device. The slave device node name shall +reflect the generic type of device for the node. + +Required Properties: + +- compatible : A string reflecting the vendor and specific device the node + represents. + +Optional Properties: + +- max-speed : The maximum baud rate the device operates at. This should + only be present if the maximum is less than the slave device + can support. For example, a particular board has some signal + quality issue or the host processor can't support higher + baud rates. + +Example: + +serial@1234 { + compatible = "ns16550a"; + interrupts = <1>; + + bluetooth { + compatible = "brcm,bcm43341-bt"; + interrupt-parent = <&gpio>; + interrupts = <10>; + }; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/guts.txt b/Documentation/devicetree/bindings/soc/fsl/guts.txt index b71b2039e112..07adca914d3d 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/guts.txt +++ b/Documentation/devicetree/bindings/soc/fsl/guts.txt @@ -25,6 +25,9 @@ Recommended properties: - fsl,liodn-bits : Indicates the number of defined bits in the LIODN registers, for those SOCs that have a PAMU device. + - little-endian : Indicates that the global utilities block is little + endian. The default is big endian. + Examples: global-utilities@e0000 { /* global utilities block */ compatible = "fsl,mpc8548-guts"; diff --git a/Documentation/devicetree/bindings/soc/fsl/qman-portals.txt b/Documentation/devicetree/bindings/soc/fsl/qman-portals.txt index 47e46ccbc170..5a34f3ab7bea 100644 --- a/Documentation/devicetree/bindings/soc/fsl/qman-portals.txt +++ b/Documentation/devicetree/bindings/soc/fsl/qman-portals.txt @@ -5,7 +5,6 @@ Copyright (C) 2008 - 2014 Freescale Semiconductor Inc. CONTENTS - QMan Portal - - QMan Pool Channel - Example QMan Portal Node @@ -82,25 +81,6 @@ These subnodes should have the following properties: Definition: The phandle to the particular hardware device that this portal is connected to. -DPAA QMan Pool Channel Nodes - -Pool Channels are defined with the following properties. - -PROPERTIES - -- compatible - Usage: Required - Value type: <stringlist> - Definition: Must include "fsl,qman-pool-channel" - May include "fsl,<SoC>-qman-pool-channel" - -- fsl,qman-channel-id - Usage: Required - Value type: <u32> - Definition: The hardware index of the channel. This can also be - determined by dividing any of the channel's 8 work queue - IDs by 8 - EXAMPLE The example below shows a (P4080) QMan portals container/bus node with two portals diff --git a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt index e8f15e34027f..16fe94d7783c 100644 --- a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt +++ b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt @@ -9,17 +9,20 @@ domain control. The driver implements the Generic PM domain bindings described in power/power_domain.txt. It provides the power domains defined in -include/dt-bindings/power/mt8173-power.h. +include/dt-bindings/power/mt8173-power.h and mt2701-power.h. Required properties: -- compatible: Must be "mediatek,mt8173-scpsys" +- compatible: Should be one of: + - "mediatek,mt2701-scpsys" + - "mediatek,mt8173-scpsys" - #power-domain-cells: Must be 1 - reg: Address range of the SCPSYS unit - infracfg: must contain a phandle to the infracfg controller - clock, clock-names: clocks according to the common clock binding. - The clocks needed "mm", "mfg", "venc" and "venc_lt". - These are the clocks which hardware needs to be enabled - before enabling certain power domains. + These are clocks which hardware needs to be + enabled before enabling certain power domains. + Required clocks for MT2701: "mm", "mfg", "ethif" + Required clocks for MT8173: "mm", "mfg", "venc", "venc_lt" Optional properties: - vdec-supply: Power supply for the vdec power domain diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt index 97d9b3e1bf39..ea1dc75ec9ea 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt @@ -43,6 +43,13 @@ The edge is described by the following properties: Definition: the identifier for the remote processor as known by the rest of the system. +- label: + Usage: optional + Value type: <string> + Definition: name of the edge, used for debugging and identification + purposes. The node name will be used if this is not + present. + = SMD DEVICES In turn, subnodes of the "edges" represent devices tied to SMD channels on that diff --git a/Documentation/devicetree/bindings/soc/rockchip/grf.txt b/Documentation/devicetree/bindings/soc/rockchip/grf.txt index 013e71a2cdc7..a0685c209218 100644 --- a/Documentation/devicetree/bindings/soc/rockchip/grf.txt +++ b/Documentation/devicetree/bindings/soc/rockchip/grf.txt @@ -5,20 +5,24 @@ is composed of many registers for system control. From RK3368 SoCs, the GRF is divided into two sections, - GRF, used for general non-secure system, +- SGRF, used for general secure system, - PMUGRF, used for always on system Required Properties: -- compatible: GRF should be one of the followings +- compatible: GRF should be one of the following: + - "rockchip,rk3036-grf", "syscon": for rk3036 - "rockchip,rk3066-grf", "syscon": for rk3066 - "rockchip,rk3188-grf", "syscon": for rk3188 - "rockchip,rk3228-grf", "syscon": for rk3228 - "rockchip,rk3288-grf", "syscon": for rk3288 - "rockchip,rk3368-grf", "syscon": for rk3368 - "rockchip,rk3399-grf", "syscon": for rk3399 -- compatible: PMUGRF should be one of the followings +- compatible: PMUGRF should be one of the following: - "rockchip,rk3368-pmugrf", "syscon": for rk3368 - "rockchip,rk3399-pmugrf", "syscon": for rk3399 +- compatible: SGRF should be one of the following + - "rockchip,rk3288-sgrf", "syscon": for rk3288 - reg: physical base address of the controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt b/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt index f909ce06afc4..01bfb6745fbd 100644 --- a/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt +++ b/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt @@ -6,6 +6,7 @@ powered up/down by software based on different application scenes to save power. Required properties for power domain controller: - compatible: Should be one of the following. "rockchip,rk3288-power-controller" - for RK3288 SoCs. + "rockchip,rk3328-power-controller" - for RK3328 SoCs. "rockchip,rk3368-power-controller" - for RK3368 SoCs. "rockchip,rk3399-power-controller" - for RK3399 SoCs. - #power-domain-cells: Number of cells in a power-domain specifier. @@ -16,6 +17,7 @@ Required properties for power domain controller: Required properties for power domain sub nodes: - reg: index of the power domain, should use macros in: "include/dt-bindings/power/rk3288-power.h" - for RK3288 type power domain. + "include/dt-bindings/power/rk3328-power.h" - for RK3328 type power domain. "include/dt-bindings/power/rk3368-power.h" - for RK3368 type power domain. "include/dt-bindings/power/rk3399-power.h" - for RK3399 type power domain. - clocks (optional): phandles to clocks which need to be enabled while power domain @@ -90,6 +92,7 @@ containing a phandle to the power device node and an index specifying which power domain to use. The index should use macros in: "include/dt-bindings/power/rk3288-power.h" - for rk3288 type power domain. + "include/dt-bindings/power/rk3328-power.h" - for rk3328 type power domain. "include/dt-bindings/power/rk3368-power.h" - for rk3368 type power domain. "include/dt-bindings/power/rk3399-power.h" - for rk3399 type power domain. diff --git a/Documentation/devicetree/bindings/soc/zte/pd-2967xx.txt b/Documentation/devicetree/bindings/soc/zte/pd-2967xx.txt new file mode 100644 index 000000000000..7629de1c2c72 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/zte/pd-2967xx.txt @@ -0,0 +1,19 @@ +* ZTE zx2967 family Power Domains + +zx2967 family includes support for multiple power domains which are used +to gate power to one or more peripherals on the processor. + +Required Properties: + - compatible: should be one of the following. + * zte,zx296718-pcu - for zx296718 power domain. + - reg: physical base address of the controller and length of memory mapped + region. + - #power-domain-cells: Must be 1. + +Example: + + pcu_domain: pcu@117000 { + compatible = "zte,zx296718-pcu"; + reg = <0x00117000 0x1000>; + #power-domain-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt b/Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt new file mode 100644 index 000000000000..fdb25b492514 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt @@ -0,0 +1,93 @@ +Devicetree bindings for the Axentia TSE-850 audio complex + +Required properties: + - compatible: "axentia,tse850-pcm5142" + - axentia,cpu-dai: The phandle of the cpu dai. + - axentia,audio-codec: The phandle of the PCM5142 codec. + - axentia,add-gpios: gpio specifier that controls the mixer. + - axentia,loop1-gpios: gpio specifier that controls loop relays on channel 1. + - axentia,loop2-gpios: gpio specifier that controls loop relays on channel 2. + - axentia,ana-supply: Regulator that supplies the output amplifier. Must + support voltages in the 2V - 20V range, in 1V steps. + +The schematics explaining the gpios are as follows: + + loop1 relays + IN1 +---o +------------+ o---+ OUT1 + \ / + + + + | / | + +--o +--. | + | add | | + | V | + | .---. | + DAC +----------->|Sum|---+ + | '---' | + | | + + + + + IN2 +---o--+------------+--o---+ OUT2 + loop2 relays + +The 'loop1' gpio pin controlls two relays, which are either in loop position, +meaning that input and output are directly connected, or they are in mixer +position, meaning that the signal is passed through the 'Sum' mixer. Similarly +for 'loop2'. + +In the above, the 'loop1' relays are inactive, thus feeding IN1 to the mixer +(if 'add' is active) and feeding the mixer output to OUT1. The 'loop2' relays +are active, short-cutting the TSE-850 from channel 2. IN1, IN2, OUT1 and OUT2 +are TSE-850 connectors and DAC is the PCB name of the (filtered) output from +the PCM5142 codec. + +Example: + + &ssc0 { + #sound-dai-cells = <0>; + + status = "okay"; + }; + + &i2c { + codec: pcm5142@4c { + compatible = "ti,pcm5142"; + + reg = <0x4c>; + + AVDD-supply = <®_3v3>; + DVDD-supply = <®_3v3>; + CPVDD-supply = <®_3v3>; + + clocks = <&sck>; + + pll-in = <3>; + pll-out = <6>; + }; + }; + + ana: ana-reg { + compatible = "pwm-regulator"; + + regulator-name = "ANA"; + + pwms = <&pwm0 2 1000 PWM_POLARITY_INVERTED>; + pwm-dutycycle-unit = <1000>; + pwm-dutycycle-range = <100 1000>; + + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <20000000>; + regulator-ramp-delay = <1000>; + }; + + sound { + compatible = "axentia,tse850-pcm5142"; + + axentia,cpu-dai = <&ssc0>; + axentia,audio-codec = <&codec>; + + axentia,add-gpios = <&pioA 8 GPIO_ACTIVE_LOW>; + axentia,loop1-gpios = <&pioA 10 GPIO_ACTIVE_LOW>; + axentia,loop2-gpios = <&pioA 11 GPIO_ACTIVE_LOW>; + + axentia,ana-supply = <&ana>; + }; diff --git a/Documentation/devicetree/bindings/sound/cs35l34.txt b/Documentation/devicetree/bindings/sound/cs35l34.txt new file mode 100644 index 000000000000..b218ead2e68e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs35l34.txt @@ -0,0 +1,64 @@ +CS35L34 Speaker Amplifier + +Required properties: + + - compatible : "cirrus,cs35l34" + + - reg : the I2C address of the device for I2C. + + - VA-supply, VP-supply : power supplies for the device, + as covered in + Documentation/devicetree/bindings/regulator/regulator.txt. + + - cirrus,boost-vtge-millivolt : Boost Voltage Value. Configures the boost + converter's output voltage in mV. The range is from VP to 8V with + increments of 100mV. + + - cirrus,boost-nanohenry: Inductor value for boost converter. The value is + in nH and they can be values of 1000nH, 1100nH, 1200nH, 1500nH, and 2200nH. + +Optional properties: + + - reset-gpios: GPIO used to reset the amplifier. + + - interrupt-parent : Specifies the phandle of the interrupt controller to + which the IRQs from CS35L34 are delivered to. + - interrupts : IRQ line info CS35L34. + (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + for further information relating to interrupt properties) + + - cirrus,boost-peak-milliamp : Boost converter peak current limit in mA. The + range starts at 1200mA and goes to a maximum of 3840mA with increments of + 80mA. The default value is 2480mA. + + - cirrus,i2s-sdinloc : ADSP SDIN I2S channel location. Indicates whether the + received mono data is in the left or right portion of the I2S frame + according to the AD0 pin or directly via this configuration. + 0x0 (Default) = Selected by AD0 input (if AD0 = LOW, use left channel), + 0x2 = Left, + 0x1 = Selected by the inversion of the AD0 input (if AD0 = LOW, use right + channel), + 0x3 = Right. + + - cirrus,gain-zc-disable: Boolean property. If set, the gain change will take + effect without waiting for a zero cross. + + - cirrus,tdm-rising-edge: Boolean property. If set, data is on the rising edge of + SCLK. Otherwise, data is on the falling edge of SCLK. + + +Example: + +cs35l34: cs35l34@40 { + compatible = "cirrus,cs35l34"; + reg = <0x40>; + + interrupt-parent = <&gpio8>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + + reset-gpios = <&gpio 10 0>; + + cirrus,boost-vtge-milltvolt = <8000>; /* 8V */ + cirrus,boost-ind-nanohenry = <1000>; /* 1uH */ + cirrus,boost-peak-milliamp = <3000>; /* 3A */ +}; diff --git a/Documentation/devicetree/bindings/sound/cs42l42.txt b/Documentation/devicetree/bindings/sound/cs42l42.txt new file mode 100644 index 000000000000..9a2c5e2423d5 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs42l42.txt @@ -0,0 +1,110 @@ +CS42L42 audio CODEC + +Required properties: + + - compatible : "cirrus,cs42l42" + + - reg : the I2C address of the device for I2C. + + - VP-supply, VCP-supply, VD_FILT-supply, VL-supply, VA-supply : + power supplies for the device, as covered in + Documentation/devicetree/bindings/regulator/regulator.txt. + +Optional properties: + + - reset-gpios : a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the codec starts. + + - interrupt-parent : Specifies the phandle of the interrupt controller to + which the IRQs from CS42L42 are delivered to. + + - interrupts : IRQ line info CS42L42. + (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + for further information relating to interrupt properties) + + - cirrus,ts-inv : Boolean property. For jacks that invert the tip sense + polarity. Normal jacks will short tip sense pin to HS1 when headphones are + plugged in and leave tip sense floating when not plugged in. Inverting jacks + short tip sense when unplugged and float when plugged in. + + 0 = (Default) Non-inverted + 1 = Inverted + + - cirrus,ts-dbnc-rise : Debounce the rising edge of TIP_SENSE_PLUG. With no + debounce, the tip sense pin might be noisy on a plug event. + + 0 - 0ms, + 1 - 125ms, + 2 - 250ms, + 3 - 500ms, + 4 - 750ms, + 5 - (Default) 1s, + 6 - 1.25s, + 7 - 1.5s, + + - cirrus,ts-dbnc-fall : Debounce the falling edge of TIP_SENSE_UNPLUG. + With no debounce, the tip sense pin might be noisy on an unplug event. + + 0 - 0ms, + 1 - 125ms, + 2 - 250ms, + 3 - 500ms, + 4 - 750ms, + 5 - (Default) 1s, + 6 - 1.25s, + 7 - 1.5s, + + - cirrus,btn-det-init-dbnce : This sets how long the driver sleeps after + enabling button detection interrupts. After auto-detection and before + servicing button interrupts, the HS bias needs time to settle. If you + don't wait, there is possibility for erroneous button interrupt. + + 0ms - 200ms, + Default = 100ms + + - cirrus,btn-det-event-dbnce : This sets how long the driver delays after + receiving a button press interrupt. With level detect interrupts, you want + to wait a small amount of time to make sure the button press is making a + clean connection with the bias resistors. + + 0ms - 20ms, + Default = 10ms + + - cirrus,bias-lvls : For a level-detect headset button scheme, each button + will bias the mic pin to a certain voltage. To determine which button was + pressed, the driver will compare this biased voltage to sequential, + decreasing voltages and will stop when a comparator is tripped, + indicating a comparator voltage < bias voltage. This value represents a + percentage of the internally generated HS bias voltage. For different + hardware setups, a designer might want to tweak this. This is an array of + descending values for the comparator voltage. + + Array of 4 values + Each 0-63 + < x1 x2 x3 x4 > + Default = < 15 8 4 1> + + +Example: + +cs42l42: cs42l42@48 { + compatible = "cirrus,cs42l42"; + reg = <0x48>; + VA-supply = <&dummy_vreg>; + VP-supply = <&dummy_vreg>; + VCP-supply = <&dummy_vreg>; + VD_FILT-supply = <&dummy_vreg>; + VL-supply = <&dummy_vreg>; + + reset-gpios = <&axi_gpio_0 1 0>; + interrupt-parent = <&gpio0>; + interrupts = <55 8> + + cirrus,ts-inv = <0x00>; + cirrus,ts-dbnc-rise = <0x05>; + cirrus,ts-dbnc-fall = <0x00>; + cirrus,btn-det-init-dbnce = <100>; + cirrus,btn-det-event-dbnce = <10>; + cirrus,bias-lvls = <0x0F 0x08 0x04 0x01>; + cirrus,hs-bias-ramp-rate = <0x02>; +};
\ No newline at end of file diff --git a/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt b/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt index 55b53e1fd72c..e0b6165c9cfc 100644 --- a/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt +++ b/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt @@ -43,7 +43,7 @@ mcbsp0: mcbsp@1d10000 { <0x00310000 0x1000>; reg-names = "mpu", "dat"; interrupts = <97 98>; - interrupts-names = "rx", "tx"; + interrupt-names = "rx", "tx"; dmas = <&edma0 3 1 &edma0 2 1>; dma-names = "tx", "rx"; diff --git a/Documentation/devicetree/bindings/sound/es8328.txt b/Documentation/devicetree/bindings/sound/es8328.txt index 30ea8a318ae9..33fbf058c997 100644 --- a/Documentation/devicetree/bindings/sound/es8328.txt +++ b/Documentation/devicetree/bindings/sound/es8328.txt @@ -4,7 +4,7 @@ This device supports both I2C and SPI. Required properties: - - compatible : "everest,es8328" + - compatible : Should be "everest,es8328" or "everest,es8388" - DVDD-supply : Regulator providing digital core supply voltage 1.8 - 3.6V - AVDD-supply : Regulator providing analog supply voltage 3.3V - PVDD-supply : Regulator providing digital IO supply voltage 1.8 - 3.6V diff --git a/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt b/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt index 3e623a724e55..9800a560e0c2 100644 --- a/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt +++ b/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt @@ -4,6 +4,7 @@ Required properties: - compatible = "mediatek,mt2701-audio"; - reg: register location and size - interrupts: Should contain AFE interrupt +- power-domains: should define the power domain - clock-names: should have these clock names: "infra_sys_audio_clk", "top_audio_mux1_sel", @@ -58,6 +59,7 @@ Example: <0 0x112A0000 0 0x20000>; interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>, <GIC_SPI 132 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>; clocks = <&infracfg CLK_INFRA_AUDIO>, <&topckgen CLK_TOP_AUD_MUX1_SEL>, <&topckgen CLK_TOP_AUD_MUX2_SEL>, diff --git a/Documentation/devicetree/bindings/sound/nau8540.txt b/Documentation/devicetree/bindings/sound/nau8540.txt new file mode 100644 index 000000000000..307a76528320 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nau8540.txt @@ -0,0 +1,16 @@ +NAU85L40 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "nuvoton,nau8540" + + - reg : the I2C address of the device. + +Example: + +codec: nau8540@1c { + compatible = "nuvoton,nau8540"; + reg = <0x1c>; +}; diff --git a/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt b/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt index d9d8635ff94c..6a4aadc4ce06 100644 --- a/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt +++ b/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt @@ -44,8 +44,7 @@ Required dai-link subnodes: Required CPU/CODEC subnodes properties: -link-name : Name of the dai link. --sound-dai : phandle and port of CPU/CODEC --capture-dai : phandle and port of CPU/CODEC +-sound-dai : phandle/s and port of CPU/CODEC Example: @@ -73,7 +72,7 @@ sound: sound { sound-dai = <&lpass MI2S_PRIMARY>; }; codec { - sound-dai = <&wcd_codec 0>; + sound-dai = <&lpass_codec 0>, <&wcd_codec 0>; }; }; diff --git a/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt new file mode 100644 index 000000000000..ccb401cfef9d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt @@ -0,0 +1,85 @@ +msm8916 analog audio CODEC + +Bindings for codec Analog IP which is integrated in pmic pm8916, + +## Bindings for codec core on pmic: + +Required properties + - compatible = "qcom,pm8916-wcd-analog-codec"; + - reg: represents the slave base address provided to the peripheral. + - interrupt-parent : The parent interrupt controller. + - interrupts: List of interrupts in given SPMI peripheral. + - interrupt-names: Names specified to above list of interrupts in same + order. List of supported interrupt names are: + "cdc_spk_cnp_int" - Speaker click and pop interrupt. + "cdc_spk_clip_int" - Speaker clip interrupt. + "cdc_spk_ocp_int" - Speaker over current protect interrupt. + "mbhc_ins_rem_det1" - jack insert removal detect interrupt 1. + "mbhc_but_rel_det" - button release interrupt. + "mbhc_but_press_det" - button press event + "mbhc_ins_rem_det" - jack insert removal detect interrupt. + "mbhc_switch_int" - multi button headset interrupt. + "cdc_ear_ocp_int" - Earphone over current protect interrupt. + "cdc_hphr_ocp_int" - Headphone R over current protect interrupt. + "cdc_hphl_ocp_det" - Headphone L over current protect interrupt. + "cdc_ear_cnp_int" - earphone cnp interrupt. + "cdc_hphr_cnp_int" - hphr click and pop interrupt. + "cdc_hphl_cnp_int" - hphl click and pop interrupt. + + - clocks: Handle to mclk. + - clock-names: should be "mclk" + - vdd-cdc-io-supply: phandle to VDD_CDC_IO regulator DT node. + - vdd-cdc-tx-rx-cx-supply: phandle to VDD_CDC_TX/RX/CX regulator DT node. + - vdd-micbias-supply: phandle of VDD_MICBIAS supply's regulator DT node. + +Optional Properties: +- qcom,micbias1-ext-cap: boolean, present if micbias1 has external capacitor + connected. +- qcom,micbias2-ext-cap: boolean, present if micbias2 has external capacitor + connected. + +Example: + +spmi_bus { + ... + audio-codec@f000{ + compatible = "qcom,pm8916-wcd-analog-codec"; + reg = <0xf000 0x200>; + reg-names = "pmic-codec-core"; + clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>; + clock-names = "mclk"; + interrupt-parent = <&spmi_bus>; + interrupts = <0x1 0xf0 0x0 IRQ_TYPE_NONE>, + <0x1 0xf0 0x1 IRQ_TYPE_NONE>, + <0x1 0xf0 0x2 IRQ_TYPE_NONE>, + <0x1 0xf0 0x3 IRQ_TYPE_NONE>, + <0x1 0xf0 0x4 IRQ_TYPE_NONE>, + <0x1 0xf0 0x5 IRQ_TYPE_NONE>, + <0x1 0xf0 0x6 IRQ_TYPE_NONE>, + <0x1 0xf0 0x7 IRQ_TYPE_NONE>, + <0x1 0xf1 0x0 IRQ_TYPE_NONE>, + <0x1 0xf1 0x1 IRQ_TYPE_NONE>, + <0x1 0xf1 0x2 IRQ_TYPE_NONE>, + <0x1 0xf1 0x3 IRQ_TYPE_NONE>, + <0x1 0xf1 0x4 IRQ_TYPE_NONE>, + <0x1 0xf1 0x5 IRQ_TYPE_NONE>; + interrupt-names = "cdc_spk_cnp_int", + "cdc_spk_clip_int", + "cdc_spk_ocp_int", + "mbhc_ins_rem_det1", + "mbhc_but_rel_det", + "mbhc_but_press_det", + "mbhc_ins_rem_det", + "mbhc_switch_int", + "cdc_ear_ocp_int", + "cdc_hphr_ocp_int", + "cdc_hphl_ocp_det", + "cdc_ear_cnp_int", + "cdc_hphr_cnp_int", + "cdc_hphl_cnp_int"; + VDD-CDC-IO-supply = <&pm8916_l5>; + VDD-CDC-TX-RX-CX-supply = <&pm8916_l5>; + VDD-MICBIAS-supply = <&pm8916_l13>; + #sound-dai-cells = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-digital.txt b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-digital.txt new file mode 100644 index 000000000000..1c8e4cb25176 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-digital.txt @@ -0,0 +1,20 @@ +msm8916 digital audio CODEC + +## Bindings for codec core in lpass: + +Required properties + - compatible = "qcom,msm8916-wcd-digital-codec"; + - reg: address space for lpass codec. + - clocks: Handle to mclk and ahbclk + - clock-names: should be "mclk", "ahbix-clk". + +Example: + +audio-codec@771c000{ + compatible = "qcom,msm8916-wcd-digital-codec"; + reg = <0x0771c000 0x400>; + clocks = <&gcc GCC_ULTAUDIO_AHBFABRIC_IXFABRIC_CLK>, + <&gcc GCC_CODEC_DIGCODEC_CLK>; + clock-names = "ahbix-clk", "mclk"; + #sound-dai-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/sound/rockchip,rk3288-hdmi-analog.txt b/Documentation/devicetree/bindings/sound/rockchip,rk3288-hdmi-analog.txt new file mode 100644 index 000000000000..2539e1d68107 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rockchip,rk3288-hdmi-analog.txt @@ -0,0 +1,36 @@ +ROCKCHIP RK3288 with HDMI and analog audio + +Required properties: +- compatible: "rockchip,rk3288-hdmi-analog" +- rockchip,model: The user-visible name of this sound complex +- rockchip,i2s-controller: The phandle of the Rockchip I2S controller that's + connected to the CODEC +- rockchip,audio-codec: The phandle of the analog audio codec. +- rockchip,routing: A list of the connections between audio components. + Each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source. For this driver the first string should always be + "Analog". + +Optionnal properties: +- rockchip,hp-en-gpios = The phandle of the GPIO that power up/down the + headphone (when the analog output is an headphone). +- rockchip,hp-det-gpios = The phandle of the GPIO that detects the headphone + (when the analog output is an headphone). +- pinctrl-names, pinctrl-0: Please refer to pinctrl-bindings.txt + +Example: + +sound { + compatible = "rockchip,rockchip-audio-es8388"; + rockchip,model = "Analog audio output"; + rockchip,i2s-controller = <&i2s>; + rockchip,audio-codec = <&es8388>; + rockchip,routing = "Analog", "LOUT2", + "Analog", "ROUT2"; + rockchip,hp-en-gpios = <&gpio8 0 GPIO_ACTIVE_HIGH>; + rockchip,hp-det-gpios = <&gpio7 7 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&headphone>; +}; + diff --git a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt index 4ea29aa9af59..a6600f6dea64 100644 --- a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt +++ b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt @@ -5,7 +5,7 @@ audio data transfer between devices in the system. Required properties: -- compatible: should be one of the followings +- compatible: should be one of the following: - "rockchip,rk3066-i2s": for rk3066 - "rockchip,rk3188-i2s", "rockchip,rk3066-i2s": for rk3188 - "rockchip,rk3288-i2s", "rockchip,rk3066-i2s": for rk3288 @@ -17,7 +17,7 @@ Required properties: Documentation/devicetree/bindings/dma/dma.txt - dma-names: should include "tx" and "rx". - clocks: a list of phandle + clock-specifer pairs, one for each entry in clock-names. -- clock-names: should contain followings: +- clock-names: should contain the following: - "i2s_hclk": clock for I2S BUS - "i2s_clk" : clock for I2S controller - rockchip,playback-channels: max playback channels, if not set, 8 channels default. diff --git a/Documentation/devicetree/bindings/sound/rt5514.txt b/Documentation/devicetree/bindings/sound/rt5514.txt index 9cabfc18cb57..929ca6756b02 100644 --- a/Documentation/devicetree/bindings/sound/rt5514.txt +++ b/Documentation/devicetree/bindings/sound/rt5514.txt @@ -13,6 +13,9 @@ Optional properties: - clocks: The phandle of the master clock to the CODEC - clock-names: Should be "mclk" +- realtek,dmic-init-delay-ms + Set the DMIC initial delay (ms) to wait it ready. + Pins on the device (for linking into audio routes) for RT5514: * DMIC1L diff --git a/Documentation/devicetree/bindings/sound/rt5663.txt b/Documentation/devicetree/bindings/sound/rt5663.txt index 7d3c974c6e2e..70eaeaed2b18 100644 --- a/Documentation/devicetree/bindings/sound/rt5663.txt +++ b/Documentation/devicetree/bindings/sound/rt5663.txt @@ -1,10 +1,10 @@ -RT5663/RT5668 audio CODEC +RT5663 audio CODEC This device supports I2C only. Required properties: -- compatible : One of "realtek,rt5663" or "realtek,rt5668". +- compatible : "realtek,rt5663". - reg : The I2C address of the device. @@ -12,7 +12,7 @@ Required properties: Optional properties: -Pins on the device (for linking into audio routes) for RT5663/RT5668: +Pins on the device (for linking into audio routes) for RT5663: * IN1P * IN1N diff --git a/Documentation/devicetree/bindings/sound/rt5665.txt b/Documentation/devicetree/bindings/sound/rt5665.txt new file mode 100644 index 000000000000..419c89219681 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5665.txt @@ -0,0 +1,68 @@ +RT5665/RT5666/RT5668 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : One of "realtek,rt5665", "realtek,rt5666" or "realtek,rt5668". + +- reg : The I2C address of the device. + +- interrupts : The CODEC's interrupt output. + +Optional properties: + +- realtek,in1-differential +- realtek,in2-differential +- realtek,in3-differential +- realtek,in4-differential + Boolean. Indicate MIC1/2/3/4 input are differential, rather than single-ended. + +- realtek,dmic1-data-pin + 0: dmic1 is not used + 1: using GPIO4 pin as dmic1 data pin + 2: using IN2N pin as dmic2 data pin + +- realtek,dmic2-data-pin + 0: dmic2 is not used + 1: using GPIO5 pin as dmic2 data pin + 2: using IN2P pin as dmic2 data pin + +- realtek,jd-src + 0: No JD is used + 1: using JD1 as JD source + +- realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin. + +Pins on the device (for linking into audio routes) for RT5659/RT5658: + + * DMIC L1 + * DMIC R1 + * DMIC L2 + * DMIC R2 + * IN1P + * IN1N + * IN2P + * IN2N + * IN3P + * IN3N + * IN4P + * IN4N + * HPOL + * HPOR + * LOUTL + * LOUTR + * MONOOUT + * PDML + * PDMR + +Example: + +rt5659 { + compatible = "realtek,rt5665"; + reg = <0x1b>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(W, 3) GPIO_ACTIVE_HIGH>; + realtek,ldo1-en-gpios = + <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/sound/samsung,tm2-audio.txt b/Documentation/devicetree/bindings/sound/samsung,tm2-audio.txt new file mode 100644 index 000000000000..94442e5673b3 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/samsung,tm2-audio.txt @@ -0,0 +1,38 @@ +Samsung Exynos5433 TM2(E) audio complex with WM5110 codec + +Required properties: + + - compatible : "samsung,tm2-audio" + - model : the user-visible name of this sound complex + - audio-codec : the phandle of the wm5110 audio codec node, + as described in ../mfd/arizona.txt + - i2s-controller : the phandle of the I2S controller + - audio-amplifier : the phandle of the MAX98504 amplifier + - samsung,audio-routing : a list of the connections between audio components; + each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source; valid names for sources and sinks are the + WM5110's and MAX98504's pins and the jacks on the + board: HP, SPK, Main Mic, Sub Mic, Third Mic, + Headset Mic + - mic-bias-gpios : GPIO pin that enables the Main Mic bias regulator + + +Example: + +sound { + compatible = "samsung,tm2-audio"; + audio-codec = <&wm5110>; + i2s-controller = <&i2s0>; + audio-amplifier = <&max98504>; + mic-bias-gpios = <&gpr3 2 0>; + model = "wm5110"; + samsung,audio-routing = + "HP", "HPOUT1L", + "HP", "HPOUT1R", + "SPK", "SPKOUT", + "SPKOUT", "HPOUT2L", + "SPKOUT", "HPOUT2R", + "Main Mic", "MICBIAS2", + "IN1R", "Main Mic"; +}; diff --git a/Documentation/devicetree/bindings/sound/sun4i-codec.txt b/Documentation/devicetree/bindings/sound/sun4i-codec.txt index 0dce690f78f5..3863531d1e6d 100644 --- a/Documentation/devicetree/bindings/sound/sun4i-codec.txt +++ b/Documentation/devicetree/bindings/sound/sun4i-codec.txt @@ -1,8 +1,12 @@ * Allwinner A10 Codec Required properties: -- compatible: must be either "allwinner,sun4i-a10-codec" or - "allwinner,sun7i-a20-codec" +- compatible: must be one of the following compatibles: + - "allwinner,sun4i-a10-codec" + - "allwinner,sun6i-a31-codec" + - "allwinner,sun7i-a20-codec" + - "allwinner,sun8i-a23-codec" + - "allwinner,sun8i-h3-codec" - reg: must contain the registers location and length - interrupts: must contain the codec interrupt - dmas: DMA channels for tx and rx dma. See the DMA client binding, @@ -10,13 +14,50 @@ Required properties: - dma-names: should include "tx" and "rx". - clocks: a list of phandle + clock-specifer pairs, one for each entry in clock-names. -- clock-names: should contain followings: +- clock-names: should contain the following: - "apb": the parent APB clock for this controller - "codec": the parent module clock Optional properties: - allwinner,pa-gpios: gpio to enable external amplifier +Required properties for the following compatibles: + - "allwinner,sun6i-a31-codec" + - "allwinner,sun8i-a23-codec" + - "allwinner,sun8i-h3-codec" +- resets: phandle to the reset control for this device +- allwinner,audio-routing: A list of the connections between audio components. + Each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source. Valid names include: + + Audio pins on the SoC: + "HP" + "HPCOM" + "LINEIN" + "LINEOUT" (not on sun8i-a23) + "MIC1" + "MIC2" + "MIC3" (sun6i-a31 only) + + Microphone biases from the SoC: + "HBIAS" + "MBIAS" + + Board connectors: + "Headphone" + "Headset Mic" + "Line In" + "Line Out" + "Mic" + "Speaker" + +Required properties for the following compatibles: + - "allwinner,sun8i-a23-codec" + - "allwinner,sun8i-h3-codec" +- allwinner,codec-analog-controls: A phandle to the codec analog controls + block in the PRCM. + Example: codec: codec@01c22c00 { #sound-dai-cells = <0>; @@ -28,3 +69,23 @@ codec: codec@01c22c00 { dmas = <&dma 0 19>, <&dma 0 19>; dma-names = "rx", "tx"; }; + +codec: codec@01c22c00 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun6i-a31-codec"; + reg = <0x01c22c00 0x98>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_APB1_CODEC>, <&ccu CLK_CODEC>; + clock-names = "apb", "codec"; + resets = <&ccu RST_APB1_CODEC>; + dmas = <&dma 15>, <&dma 15>; + dma-names = "rx", "tx"; + allwinner,audio-routing = + "Headphone", "HP", + "Speaker", "LINEOUT", + "LINEIN", "Line In", + "MIC1", "MBIAS", + "MIC1", "Mic", + "MIC2", "HBIAS", + "MIC2", "Headset Mic"; +}; diff --git a/Documentation/devicetree/bindings/sound/sun4i-i2s.txt b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt index 7b526ec64991..ee21da865771 100644 --- a/Documentation/devicetree/bindings/sound/sun4i-i2s.txt +++ b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt @@ -5,8 +5,9 @@ audio data transfer between devices in the system. Required properties: -- compatible: should be one of the followings +- compatible: should be one of the following: - "allwinner,sun4i-a10-i2s" + - "allwinner,sun6i-a31-i2s" - reg: physical base address of the controller and length of memory mapped region. - interrupts: should contain the I2S interrupt. @@ -14,11 +15,15 @@ Required properties: Documentation/devicetree/bindings/dma/dma.txt - dma-names: should include "tx" and "rx". - clocks: a list of phandle + clock-specifer pairs, one for each entry in clock-names. -- clock-names: should contain followings: +- clock-names: should contain the following: - "apb" : clock for the I2S bus interface - "mod" : module clock for the I2S controller - #sound-dai-cells : Must be equal to 0 +Required properties for the following compatibles: + - "allwinner,sun6i-a31-i2s" +- resets: phandle to the reset line for this codec + Example: i2s0: i2s@01c22400 { diff --git a/Documentation/devicetree/bindings/sound/sun8i-a33-codec.txt b/Documentation/devicetree/bindings/sound/sun8i-a33-codec.txt new file mode 100644 index 000000000000..399b1b4bae22 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/sun8i-a33-codec.txt @@ -0,0 +1,63 @@ +Allwinner SUN8I audio codec +------------------------------------ + +On Sun8i-A33 SoCs, the audio is separated in different parts: + - A DAI driver. It uses the "sun4i-i2s" driver which is + documented here: + Documentation/devicetree/bindings/sound/sun4i-i2s.txt + - An analog part of the codec which is handled as PRCM registers. + See Documentation/devicetree/bindings/sound/sun8i-codec-analog.txt + - An digital part of the codec which is documented in this current + binding documentation. + - And finally, an audio card which links all the above components. + The simple-audio card will be used. + See Documentation/devicetree/bindings/sound/simple-card.txt + +This bindings documentation exposes Sun8i codec (digital part). + +Required properties: +- compatible: must be "allwinner,sun8i-a33-codec" +- reg: must contain the registers location and length +- interrupts: must contain the codec interrupt +- clocks: a list of phandle + clock-specifer pairs, one for each entry + in clock-names. +- clock-names: should contain followings: + - "bus": the parent APB clock for this controller + - "mod": the parent module clock + +Here is an example to add a sound card and the codec binding on sun8i SoCs that +are similar to A33 using simple-card: + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "sun8i-a33-audio"; + simple-audio-card,format = "i2s"; + simple-audio-card,frame-master = <&link_codec>; + simple-audio-card,bitclock-master = <&link_codec>; + simple-audio-card,mclk-fs = <512>; + simple-audio-card,aux-devs = <&codec_analog>; + simple-audio-card,routing = + "Left DAC", "Digital Left DAC", + "Right DAC", "Digital Right DAC"; + + simple-audio-card,cpu { + sound-dai = <&dai>; + }; + + link_codec: simple-audio-card,codec { + sound-dai = <&codec>; + }; + + soc@01c00000 { + [...] + + audio-codec@1c22e00 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun8i-a33-codec"; + reg = <0x01c22e00 0x400>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>; + clock-names = "bus", "mod"; + }; + }; + diff --git a/Documentation/devicetree/bindings/sound/sun8i-codec-analog.txt b/Documentation/devicetree/bindings/sound/sun8i-codec-analog.txt new file mode 100644 index 000000000000..779b735781ba --- /dev/null +++ b/Documentation/devicetree/bindings/sound/sun8i-codec-analog.txt @@ -0,0 +1,16 @@ +* Allwinner Codec Analog Controls + +Required properties: +- compatible: must be one of the following compatibles: + - "allwinner,sun8i-a23-codec-analog" + - "allwinner,sun8i-h3-codec-analog" + +Required properties if not a sub-node of the PRCM node: +- reg: must contain the registers location and length + +Example: +prcm: prcm@01f01400 { + codec_analog: codec-analog { + compatible = "allwinner,sun8i-a23-codec-analog"; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/sunxi,sun4i-spdif.txt b/Documentation/devicetree/bindings/sound/sunxi,sun4i-spdif.txt index 0230c4d20506..fe0a65e6d629 100644 --- a/Documentation/devicetree/bindings/sound/sunxi,sun4i-spdif.txt +++ b/Documentation/devicetree/bindings/sound/sunxi,sun4i-spdif.txt @@ -10,6 +10,7 @@ Required properties: - compatible : should be one of the following: - "allwinner,sun4i-a10-spdif": for the Allwinner A10 SoC - "allwinner,sun6i-a31-spdif": for the Allwinner A31 SoC + - "allwinner,sun8i-h3-spdif": for the Allwinner H3 SoC - reg : Offset and length of the register set for the device. diff --git a/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt b/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt index 9340d2ddcc54..6fbba562eaa7 100644 --- a/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt +++ b/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt @@ -12,6 +12,7 @@ Required properties: "ti,tlv320aic3120" - TLV320AIC3120 (mono speaker amp, MiniDSP) "ti,tlv320aic3111" - TLV320AIC3111 (stereo speaker amp, MiniDSP) "ti,tlv320dac3100" - TLV320DAC3100 (no ADC, mono speaker amp, no MiniDSP) + "ti,tlv320dac3101" - TLV320DAC3101 (no ADC, stereo speaker amp, no MiniDSP) - reg - <int> - I2C slave address - HPVDD-supply, SPRVDD-supply, SPLVDD-supply, AVDD-supply, IOVDD-supply, diff --git a/Documentation/devicetree/bindings/sound/wm8580.txt b/Documentation/devicetree/bindings/sound/wm8580.txt index 7d9821f348da..78fce9b14954 100644 --- a/Documentation/devicetree/bindings/sound/wm8580.txt +++ b/Documentation/devicetree/bindings/sound/wm8580.txt @@ -1,10 +1,10 @@ -WM8580 audio CODEC +WM8580 and WM8581 audio CODEC This device supports I2C only. Required properties: - - compatible : "wlf,wm8580" + - compatible : "wlf,wm8580", "wlf,wm8581" - reg : the I2C address of the device. diff --git a/Documentation/devicetree/bindings/sound/zte,zx-i2s.txt b/Documentation/devicetree/bindings/sound/zte,zx-i2s.txt index 7e5aa6f6b5a1..292ad5083704 100644 --- a/Documentation/devicetree/bindings/sound/zte,zx-i2s.txt +++ b/Documentation/devicetree/bindings/sound/zte,zx-i2s.txt @@ -1,10 +1,12 @@ ZTE ZX296702 I2S controller Required properties: - - compatible : Must be "zte,zx296702-i2s" + - compatible : Must be one of: + "zte,zx296718-i2s", "zte,zx296702-i2s" + "zte,zx296702-i2s" - reg : Must contain I2S core's registers location and length - clocks : Pairs of phandle and specifier referencing the controller's clocks. - - clock-names: "tx" for the clock to the I2S interface. + - clock-names: "wclk" for the wclk, "pclk" for the pclk to the I2S interface. - dmas: Pairs of phandle and specifier for the DMA channel that is used by the core. The core expects two dma channels for transmit. - dma-names : Must be "tx" and "rx" @@ -16,12 +18,12 @@ please check: * dma/dma.txt Example: - i2s0: i2s0@0b005000 { + i2s0: i2s@b005000 { #sound-dai-cells = <0>; - compatible = "zte,zx296702-i2s"; + compatible = "zte,zx296718-i2s", "zte,zx296702-i2s"; reg = <0x0b005000 0x1000>; - clocks = <&lsp0clk ZX296702_I2S0_DIV>; - clock-names = "tx"; + clocks = <&audiocrm AUDIO_I2S0_WCLK>, <&audiocrm AUDIO_I2S0_PCLK>; + clock-names = "wclk", "pclk"; interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; dmas = <&dma 5>, <&dma 6>; dma-names = "tx", "rx"; diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index aa005c1d10d9..dc975064fa27 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -1,16 +1,23 @@ Renesas MSIOF spi controller Required properties: -- compatible : "renesas,msiof-<soctype>" for SoCs, - "renesas,sh-msiof" for SuperH, or - "renesas,sh-mobile-msiof" for SH Mobile series. - Examples with soctypes are: - "renesas,msiof-r8a7790" (R-Car H2) +- compatible : "renesas,msiof-r8a7790" (R-Car H2) "renesas,msiof-r8a7791" (R-Car M2-W) "renesas,msiof-r8a7792" (R-Car V2H) "renesas,msiof-r8a7793" (R-Car M2-N) "renesas,msiof-r8a7794" (R-Car E2) + "renesas,msiof-r8a7796" (R-Car M3-W) "renesas,msiof-sh73a0" (SH-Mobile AG5) + "renesas,sh-mobile-msiof" (generic SH-Mobile compatibile device) + "renesas,rcar-gen2-msiof" (generic R-Car Gen2 compatible device) + "renesas,rcar-gen3-msiof" (generic R-Car Gen3 compatible device) + "renesas,sh-msiof" (deprecated) + + When compatible with the generic version, nodes + must list the SoC-specific version corresponding + to the platform first followed by the generic + version. + - reg : A list of offsets and lengths of the register sets for the device. If only one register set is present, it is to be used @@ -60,7 +67,8 @@ Documentation/devicetree/bindings/pinctrl/renesas,*. Example: msiof0: spi@e6e20000 { - compatible = "renesas,msiof-r8a7791"; + compatible = "renesas,msiof-r8a7791", + "renesas,rcar-gen2-msiof"; reg = <0 0xe6e20000 0 0x0064>; interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp0_clks R8A7791_CLK_MSIOF0>; diff --git a/Documentation/devicetree/bindings/spi/spi-armada-3700.txt b/Documentation/devicetree/bindings/spi/spi-armada-3700.txt new file mode 100644 index 000000000000..1564aa8c02cd --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-armada-3700.txt @@ -0,0 +1,25 @@ +* Marvell Armada 3700 SPI Controller + +Required Properties: + +- compatible: should be "marvell,armada-3700-spi" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: The interrupt number. The interrupt specifier format depends on + the interrupt controller and of its driver. +- clocks: Must contain the clock source, usually from the North Bridge clocks. +- num-cs: The number of chip selects that is supported by this SPI Controller +- #address-cells: should be 1. +- #size-cells: should be 0. + +Example: + + spi0: spi@10600 { + compatible = "marvell,armada-3700-spi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10600 0x5d>; + clocks = <&nb_perih_clk 7>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; + num-cs = <4>; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt new file mode 100644 index 000000000000..225ace1d0c65 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt @@ -0,0 +1,19 @@ +* Freescale Low Power SPI (LPSPI) for i.MX + +Required properties: +- compatible : + - "fsl,imx7ulp-spi" for LPSPI compatible with the one integrated on i.MX7ULP soc +- reg : address and length of the lpspi master registers +- interrupt-parent : core interrupt controller +- interrupts : lpspi interrupt +- clocks : lpspi clock specifier + +Examples: + +lpspi2: lpspi@40290000 { + compatible = "fsl,imx7ulp-spi"; + reg = <0x40290000 0x10000>; + interrupt-parent = <&intc>; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7ULP_CLK_LPSPI2>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-lantiq-ssc.txt b/Documentation/devicetree/bindings/spi/spi-lantiq-ssc.txt new file mode 100644 index 000000000000..6069b95a883d --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-lantiq-ssc.txt @@ -0,0 +1,29 @@ +Lantiq Synchronous Serial Controller (SSC) SPI master driver + +Required properties: +- compatible: "lantiq,ase-spi", "lantiq,falcon-spi", "lantiq,xrx100-spi" +- #address-cells: see spi-bus.txt +- #size-cells: see spi-bus.txt +- reg: address and length of the spi master registers +- interrupts: should contain the "spi_rx", "spi_tx" and "spi_err" interrupt. + + +Optional properties: +- clocks: spi clock phandle +- num-cs: see spi-bus.txt, set to 8 if unset +- base-cs: the number of the first chip select, set to 1 if unset. + +Example: + + +spi: spi@E100800 { + compatible = "lantiq,xrx200-spi", "lantiq,xrx100-spi"; + reg = <0xE100800 0x100>; + interrupt-parent = <&icu0>; + interrupts = <22 23 24>; + interrupt-names = "spi_rx", "spi_tx", "spi_err"; + #address-cells = <1>; + #size-cells = <1>; + num-cs = <6>; + base-cs = <1>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-rockchip.txt b/Documentation/devicetree/bindings/spi/spi-rockchip.txt index d2ca153614f9..83da4931d832 100644 --- a/Documentation/devicetree/bindings/spi/spi-rockchip.txt +++ b/Documentation/devicetree/bindings/spi/spi-rockchip.txt @@ -31,6 +31,10 @@ Optional Properties: - rx-sample-delay-ns: nanoseconds to delay after the SCLK edge before sampling Rx data (may need to be fine tuned for high capacitance lines). No delay (0) by default. +- pinctrl-names: Names for the pin configuration(s); may be "default" or + "sleep", where the "sleep" configuration may describe the state + the pins should be in during system suspend. See also + pinctrl/pinctrl-bindings.txt. Example: @@ -46,4 +50,7 @@ Example: interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>; clock-names = "spiclk", "apb_pclk"; + pinctrl-0 = <&spi1_pins>; + pinctrl-1 = <&spi1_sleep>; + pinctrl-names = "default", "sleep"; }; diff --git a/Documentation/devicetree/bindings/spi/spi-sun6i.txt b/Documentation/devicetree/bindings/spi/spi-sun6i.txt index 21de73db6a05..2ec99b86b622 100644 --- a/Documentation/devicetree/bindings/spi/spi-sun6i.txt +++ b/Documentation/devicetree/bindings/spi/spi-sun6i.txt @@ -1,7 +1,7 @@ -Allwinner A31 SPI controller +Allwinner A31/H3 SPI controller Required properties: -- compatible: Should be "allwinner,sun6i-a31-spi". +- compatible: Should be "allwinner,sun6i-a31-spi" or "allwinner,sun8i-h3-spi". - reg: Should contain register location and length. - interrupts: Should contain interrupt. - clocks: phandle to the clocks feeding the SPI controller. Two are @@ -12,6 +12,11 @@ Required properties: - resets: phandle to the reset controller asserting this device in reset +Optional properties: +- dmas: DMA specifiers for rx and tx dma. See the DMA client binding, + Documentation/devicetree/bindings/dma/dma.txt +- dma-names: DMA request names should include "rx" and "tx" if present. + Example: spi1: spi@01c69000 { @@ -22,3 +27,19 @@ spi1: spi@01c69000 { clock-names = "ahb", "mod"; resets = <&ahb1_rst 21>; }; + +spi0: spi@01c68000 { + compatible = "allwinner,sun8i-h3-spi"; + reg = <0x01c68000 0x1000>; + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>; + clock-names = "ahb", "mod"; + dmas = <&dma 23>, <&dma 23>; + dma-names = "rx", "tx"; + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins>; + resets = <&ccu RST_BUS_SPI0>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/sram/sram.txt b/Documentation/devicetree/bindings/sram/sram.txt index add48f09015e..267da4410aef 100644 --- a/Documentation/devicetree/bindings/sram/sram.txt +++ b/Documentation/devicetree/bindings/sram/sram.txt @@ -4,7 +4,7 @@ Simple IO memory regions to be managed by the genalloc API. Required properties: -- compatible : mmio-sram +- compatible : mmio-sram or atmel,sama5d2-securam - reg : SRAM iomem address range @@ -42,6 +42,12 @@ Optional properties in the area nodes: and in use by another device or devices - export : indicates that the reserved SRAM area may be accessed outside of the kernel, e.g. by bootloader or userspace +- protect-exec : Same as 'pool' above but with the additional + constraint that code wil be run from the region and + that the memory is maintained as read-only, executable + during code execution. NOTE: This region must be page + aligned on start and end in order to properly allow + manipulation of the page attributes. - label : the name for the reserved partition, if omitted, the label is taken from the node name excluding the unit address. diff --git a/Documentation/devicetree/bindings/submitting-patches.txt b/Documentation/devicetree/bindings/submitting-patches.txt index 7d44eae7ab0b..274058c583dd 100644 --- a/Documentation/devicetree/bindings/submitting-patches.txt +++ b/Documentation/devicetree/bindings/submitting-patches.txt @@ -3,7 +3,7 @@ I. For patch submitters - 0) Normal patch submission rules from Documentation/SubmittingPatches + 0) Normal patch submission rules from Documentation/process/submitting-patches.rst applies. 1) The Documentation/ portion of the patch should be a separate patch. diff --git a/Documentation/devicetree/bindings/thermal/brcm,bcm2835-thermal.txt b/Documentation/devicetree/bindings/thermal/brcm,bcm2835-thermal.txt new file mode 100644 index 000000000000..474531d2b2c5 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/brcm,bcm2835-thermal.txt @@ -0,0 +1,17 @@ +Binding for Thermal Sensor driver for BCM2835 SoCs. + +Required parameters: +------------------- + +compatible: should be one of: "brcm,bcm2835-thermal", + "brcm,bcm2836-thermal" or "brcm,bcm2837-thermal" +reg: Address range of the thermal registers. +clocks: Phandle of the clock used by the thermal sensor. + +Example: + +thermal: thermal@7e212000 { + compatible = "brcm,bcm2835-thermal"; + reg = <0x7e212000 0x8>; + clocks = <&clocks BCM2835_CLOCK_TSENS>; +}; diff --git a/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt index 66223d561972..20ca4ef9d776 100644 --- a/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt @@ -17,6 +17,12 @@ Required properties: calibration data, as specified by the SoC reference manual. The first cell of each pair is the value to be written to TTCFGR, and the second is the value to be written to TSCFGR. +- #thermal-sensor-cells : Must be 1. The sensor specifier is the monitoring + site ID, and represents the "n" in TRITSRn and TRATSRn. + +Optional property: +- little-endian : If present, the TMU registers are little endian. If absent, + the default is big endian. Example: @@ -60,4 +66,5 @@ tmu@f0000 { 0x00030000 0x00000012 0x00030001 0x0000001d>; + #thermal-sensor-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/thermal/rcar-gen3-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-gen3-thermal.txt new file mode 100644 index 000000000000..07a9713ae6a7 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/rcar-gen3-thermal.txt @@ -0,0 +1,56 @@ +* DT bindings for Renesas R-Car Gen3 Thermal Sensor driver + +On R-Car Gen3 SoCs, the thermal sensor controllers (TSC) control the thermal +sensors (THS) which are the analog circuits for measuring temperature (Tj) +inside the LSI. + +Required properties: +- compatible : "renesas,<soctype>-thermal", + Examples with soctypes are: + - "renesas,r8a7795-thermal" (R-Car H3) + - "renesas,r8a7796-thermal" (R-Car M3-W) +- reg : Address ranges of the thermal registers. Each sensor + needs one address range. Sorting must be done in + increasing order according to datasheet, i.e. + TSC1, TSC2, ... +- clocks : Must contain a reference to the functional clock. +- #thermal-sensor-cells : must be <1>. + +Optional properties: + +- interrupts : interrupts routed to the TSC (3 for H3 and M3-W) +- power-domain : Must contain a reference to the power domain. This + property is mandatory if the thermal sensor instance + is part of a controllable power domain. + +Example: + + tsc: thermal@e6198000 { + compatible = "renesas,r8a7795-thermal"; + reg = <0 0xe6198000 0 0x68>, + <0 0xe61a0000 0 0x5c>, + <0 0xe61a8000 0 0x5c>; + interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 522>; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + #thermal-sensor-cells = <1>; + status = "okay"; + }; + + thermal-zones { + sensor_thermal1: sensor-thermal1 { + polling-delay-passive = <250>; + polling-delay = <1000>; + thermal-sensors = <&tsc 0>; + + trips { + sensor1_crit: sensor1-crit { + temperature = <90000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt index 08efe6bc2193..43003aec94bd 100644 --- a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt @@ -22,10 +22,13 @@ Required properties: TSADC controller. - pinctrl-2 : The "sleep" pinctrl state, it will be in for suspend. - #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description. + +Optional properties: - rockchip,hw-tshut-temp : The hardware-controlled shutdown temperature value. - rockchip,hw-tshut-mode : The hardware-controlled shutdown mode 0:CRU 1:GPIO. - rockchip,hw-tshut-polarity : The hardware-controlled active polarity 0:LOW 1:HIGH. +- rockchip,grf : The phandle of the syscon node for the general register file. Exiample: tsadc: tsadc@ff280000 { diff --git a/Documentation/devicetree/bindings/thermal/st-thermal.txt b/Documentation/devicetree/bindings/thermal/st-thermal.txt index 3b9251b4a145..a2f939137e35 100644 --- a/Documentation/devicetree/bindings/thermal/st-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/st-thermal.txt @@ -3,17 +3,8 @@ Binding for Thermal Sensor driver for STMicroelectronics STi series of SoCs. Required parameters: ------------------- -compatible : st,<SoC>-<module>-thermal; should be one of: - "st,stih415-sas-thermal", - "st,stih415-mpe-thermal", - "st,stih416-sas-thermal" - "st,stih416-mpe-thermal" - "st,stid127-thermal" or - "st,stih407-thermal" - according to the SoC type (stih415, stih416, stid127, stih407) - and module type (sas or mpe). On stid127 & stih407 there is only - one die/module, so there is no module type in the compatible - string. +compatible : Should be "st,stih407-thermal" + clock-names : Should be "thermal". See: Documentation/devicetree/bindings/resource-names.txt clocks : Phandle of the clock used by the thermal sensor. @@ -25,18 +16,17 @@ Optional parameters: reg : For non-sysconf based sensors, this should be the physical base address and length of the sensor's registers. interrupts : Standard way to define interrupt number. - Interrupt is mandatory to be defined when compatible is - "stih416-mpe-thermal". NB: For thermal sensor's for which no interrupt has been defined, a polling delay of 1000ms will be used to read the temperature from device. Example: - temp1@fdfe8000 { - compatible = "st,stih416-mpe-thermal"; - reg = <0xfdfe8000 0x10>; - clock-names = "thermal"; - clocks = <&clk_m_mpethsens>; - interrupts = <GIC_SPI 23 IRQ_TYPE_NONE>; + temp0@91a0000 { + compatible = "st,stih407-thermal"; + reg = <0x91a0000 0x28>; + clock-names = "thermal"; + clocks = <&CLK_SYSIN>; + interrupts = <GIC_SPI 205 IRQ_TYPE_EDGE_RISING>; + st,passive_cooling_temp = <110>; }; diff --git a/Documentation/devicetree/bindings/thermal/zx2967-thermal.txt b/Documentation/devicetree/bindings/thermal/zx2967-thermal.txt new file mode 100644 index 000000000000..3dc1c6bf0478 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/zx2967-thermal.txt @@ -0,0 +1,116 @@ +* ZTE zx2967 family Thermal + +Required Properties: +- compatible: should be one of the following. + * zte,zx296718-thermal +- reg: physical base address of the controller and length of memory mapped + region. +- clocks : Pairs of phandle and specifier referencing the controller's clocks. +- clock-names: "topcrm" for the topcrm clock. + "apb" for the apb clock. +- #thermal-sensor-cells: must be 0. + +Please note: slope coefficient defined in thermal-zones section need to be +multiplied by 1000. + +Example for tempsensor: + + tempsensor: tempsensor@148a000 { + compatible = "zte,zx296718-thermal"; + reg = <0x0148a000 0x20>; + clocks = <&topcrm TEMPSENSOR_GATE>, <&audiocrm AUDIO_TS_PCLK>; + clock-names = "topcrm", "apb"; + #thermal-sensor-cells = <0>; + }; + +Example for cooling device: + + cooling_dev: cooling_dev { + cluster0_cooling_dev: cluster0-cooling-dev { + #cooling-cells = <2>; + cpumask = <0xf>; + capacitance = <1500>; + }; + + cluster1_cooling_dev: cluster1-cooling-dev { + #cooling-cells = <2>; + cpumask = <0x30>; + capacitance = <2000>; + }; + }; + +Example for thermal zones: + + thermal-zones { + zx296718_thermal: zx296718_thermal { + polling-delay-passive = <500>; + polling-delay = <1000>; + sustainable-power = <6500>; + + thermal-sensors = <&tempsensor 0>; + /* + * slope need to be multiplied by 1000. + */ + coefficients = <1951 (-922)>; + + trips { + trip0: switch_on_temperature { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + trip1: desired_temperature { + temperature = <100000>; + hysteresis = <2000>; + type = "passive"; + }; + + crit: critical_temperature { + temperature = <110000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&trip0>; + cooling-device = <&gpu 2 5>; + }; + + map1 { + trip = <&trip0>; + cooling-device = <&cluster0_cooling_dev 1 2>; + }; + + map2 { + trip = <&trip1>; + cooling-device = <&cluster0_cooling_dev 1 2>; + }; + + map3 { + trip = <&crit>; + cooling-device = <&cluster0_cooling_dev 1 2>; + }; + + map4 { + trip = <&trip0>; + cooling-device = <&cluster1_cooling_dev 1 2>; + contribution = <9000>; + }; + + map5 { + trip = <&trip1>; + cooling-device = <&cluster1_cooling_dev 1 2>; + contribution = <4096>; + }; + + map6 { + trip = <&crit>; + cooling-device = <&cluster1_cooling_dev 1 2>; + contribution = <4096>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/timer/cortina,gemini-timer.txt b/Documentation/devicetree/bindings/timer/cortina,gemini-timer.txt new file mode 100644 index 000000000000..16ea1d3b2e9e --- /dev/null +++ b/Documentation/devicetree/bindings/timer/cortina,gemini-timer.txt @@ -0,0 +1,22 @@ +Cortina Systems Gemini timer + +This timer is embedded in the Cortina Systems Gemini SoCs. + +Required properties: + +- compatible : Must be "cortina,gemini-timer" +- reg : Should contain registers location and length +- interrupts : Should contain the three timer interrupts with + flags for rising edge +- syscon : a phandle to the global Gemini system controller + +Example: + +timer@43000000 { + compatible = "cortina,gemini-timer"; + reg = <0x43000000 0x1000>; + interrupts = <14 IRQ_TYPE_EDGE_RISING>, /* Timer 1 */ + <15 IRQ_TYPE_EDGE_RISING>, /* Timer 2 */ + <16 IRQ_TYPE_EDGE_RISING>; /* Timer 3 */ + syscon = <&syscon>; +}; diff --git a/Documentation/devicetree/bindings/timer/ezchip,nps400-timer0.txt b/Documentation/devicetree/bindings/timer/ezchip,nps400-timer0.txt new file mode 100644 index 000000000000..e3cfce8fecc5 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/ezchip,nps400-timer0.txt @@ -0,0 +1,17 @@ +NPS Network Processor + +Required properties: + +- compatible : should be "ezchip,nps400-timer0" + +Clocks required for compatible = "ezchip,nps400-timer0": +- interrupts : The interrupt of the first timer +- clocks : Must contain a single entry describing the clock input + +Example: + +timer { + compatible = "ezchip,nps400-timer0"; + interrupts = <3>; + clocks = <&sysclk>; +}; diff --git a/Documentation/devicetree/bindings/timer/ezchip,nps400-timer.txt b/Documentation/devicetree/bindings/timer/ezchip,nps400-timer1.txt index c8c03d700382..c0ab4190b8fb 100644 --- a/Documentation/devicetree/bindings/timer/ezchip,nps400-timer.txt +++ b/Documentation/devicetree/bindings/timer/ezchip,nps400-timer1.txt @@ -2,14 +2,14 @@ NPS Network Processor Required properties: -- compatible : should be "ezchip,nps400-timer" +- compatible : should be "ezchip,nps400-timer1" -Clocks required for compatible = "ezchip,nps400-timer": +Clocks required for compatible = "ezchip,nps400-timer1": - clocks : Must contain a single entry describing the clock input Example: timer { - compatible = "ezchip,nps400-timer"; + compatible = "ezchip,nps400-timer1"; clocks = <&sysclk>; }; diff --git a/Documentation/devicetree/bindings/timer/renesas,ostm.txt b/Documentation/devicetree/bindings/timer/renesas,ostm.txt new file mode 100644 index 000000000000..be3ae0fdf775 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/renesas,ostm.txt @@ -0,0 +1,30 @@ +* Renesas OS Timer (OSTM) + +The OSTM is a multi-channel 32-bit timer/counter with fixed clock +source that can operate in either interval count down timer or free-running +compare match mode. + +Channels are independent from each other. + +Required Properties: + + - compatible: must be one or more of the following: + - "renesas,r7s72100-ostm" for the r7s72100 OSTM + - "renesas,ostm" for any OSTM + This is a fallback for the above renesas,*-ostm entries + + - reg: base address and length of the register block for a timer channel. + + - interrupts: interrupt specifier for the timer channel. + + - clocks: clock specifier for the timer channel. + +Example: R7S72100 (RZ/A1H) OSTM node + + ostm0: timer@fcfec000 { + compatible = "renesas,r7s72100-ostm", "renesas,ostm"; + reg = <0xfcfec000 0x30>; + interrupts = <GIC_SPI 102 IRQ_TYPE_EDGE_RISING>; + clocks = <&mstp5_clks R7S72100_CLK_OSTM0>; + power-domains = <&cpg_clocks>; + }; diff --git a/Documentation/devicetree/bindings/ufs/ufs-qcom.txt b/Documentation/devicetree/bindings/ufs/ufs-qcom.txt index 070baf4d7d97..1f69ee1a61ea 100644 --- a/Documentation/devicetree/bindings/ufs/ufs-qcom.txt +++ b/Documentation/devicetree/bindings/ufs/ufs-qcom.txt @@ -7,8 +7,11 @@ To bind UFS PHY with UFS host controller, the controller node should contain a phandle reference to UFS PHY node. Required properties: -- compatible : compatible list, contains "qcom,ufs-phy-qmp-20nm" - or "qcom,ufs-phy-qmp-14nm" according to the relevant phy in use. +- compatible : compatible list, contains one of the following - + "qcom,ufs-phy-qmp-20nm" for 20nm ufs phy, + "qcom,ufs-phy-qmp-14nm" for legacy 14nm ufs phy, + "qcom,msm8996-ufs-phy-qmp-14nm" for 14nm ufs phy + present on MSM8996 chipset. - reg : should contain PHY register address space (mandatory), - reg-names : indicates various resources passed to driver (via reg proptery) by name. Required "reg-names" is "phy_mem". @@ -26,7 +29,6 @@ Optional properties: - vdda-pll-max-microamp : specifies max. load that can be drawn from pll supply - vddp-ref-clk-supply : phandle to UFS device ref_clk pad power supply - vddp-ref-clk-max-microamp : specifies max. load that can be drawn from this supply -- vddp-ref-clk-always-on : specifies if this supply needs to be kept always on Example: diff --git a/Documentation/devicetree/bindings/usb/allwinner,sun4i-a10-musb.txt b/Documentation/devicetree/bindings/usb/allwinner,sun4i-a10-musb.txt index 862cd7c79805..d9b42da016f3 100644 --- a/Documentation/devicetree/bindings/usb/allwinner,sun4i-a10-musb.txt +++ b/Documentation/devicetree/bindings/usb/allwinner,sun4i-a10-musb.txt @@ -2,8 +2,8 @@ Allwinner sun4i A10 musb DRC/OTG controller ------------------------------------------- Required properties: - - compatible : "allwinner,sun4i-a10-musb", "allwinner,sun6i-a31-musb" - or "allwinner,sun8i-a33-musb" + - compatible : "allwinner,sun4i-a10-musb", "allwinner,sun6i-a31-musb", + "allwinner,sun8i-a33-musb" or "allwinner,sun8i-h3-musb" - reg : mmio address range of the musb controller - clocks : clock specifier for the musb controller ahb gate clock - reset : reset specifier for the ahb reset (A31 and newer only) diff --git a/Documentation/devicetree/bindings/usb/atmel-usb.txt b/Documentation/devicetree/bindings/usb/atmel-usb.txt index f4262ed60582..ad8ea56a9ed3 100644 --- a/Documentation/devicetree/bindings/usb/atmel-usb.txt +++ b/Documentation/devicetree/bindings/usb/atmel-usb.txt @@ -6,9 +6,9 @@ Required properties: - compatible: Should be "atmel,at91rm9200-ohci" for USB controllers used in host mode. - reg: Address and length of the register set for the device - - interrupts: Should contain ehci interrupt + - interrupts: Should contain ohci interrupt - clocks: Should reference the peripheral, host and system clocks - - clock-names: Should contains two strings + - clock-names: Should contain three strings "ohci_clk" for the peripheral clock "hclk" for the host clock "uhpck" for the system clock @@ -35,7 +35,7 @@ Required properties: - reg: Address and length of the register set for the device - interrupts: Should contain ehci interrupt - clocks: Should reference the peripheral and the UTMI clocks - - clock-names: Should contains two strings + - clock-names: Should contain two strings "ehci_clk" for the peripheral clock "usb_clk" for the UTMI clock @@ -58,7 +58,7 @@ Required properties: - reg: Address and length of the register set for the device - interrupts: Should contain macb interrupt - clocks: Should reference the peripheral and the AHB clocks - - clock-names: Should contains two strings + - clock-names: Should contain two strings "pclk" for the peripheral clock "hclk" for the AHB clock @@ -85,7 +85,7 @@ Required properties: - reg: Address and length of the register set for the device - interrupts: Should contain usba interrupt - clocks: Should reference the peripheral and host clocks - - clock-names: Should contains two strings + - clock-names: Should contain two strings "pclk" for the peripheral clock "hclk" for the host clock - ep childnode: To specify the number of endpoints and their properties. diff --git a/Documentation/devicetree/bindings/usb/da8xx-usb.txt b/Documentation/devicetree/bindings/usb/da8xx-usb.txt new file mode 100644 index 000000000000..ccb844aba7d4 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/da8xx-usb.txt @@ -0,0 +1,43 @@ +TI DA8xx MUSB +~~~~~~~~~~~~~ +For DA8xx/OMAP-L1x/AM17xx/AM18xx platforms. + +Required properties: +~~~~~~~~~~~~~~~~~~~~ + - compatible : Should be set to "ti,da830-musb". + + - reg: Offset and length of the USB controller register set. + + - interrupts: The USB interrupt number. + + - interrupt-names: Should be set to "mc". + + - dr_mode: The USB operation mode. Should be one of "host", "peripheral" or "otg". + + - phys: Phandle for the PHY device + + - phy-names: Should be "usb-phy" + +Optional properties: +~~~~~~~~~~~~~~~~~~~~ + - vbus-supply: Phandle to a regulator providing the USB bus power. + +Example: + usb_phy: usb-phy { + compatible = "ti,da830-usb-phy"; + #phy-cells = <0>; + status = "okay"; + }; + usb0: usb@200000 { + compatible = "ti,da830-musb"; + reg = <0x00200000 0x10000>; + interrupts = <58>; + interrupt-names = "mc"; + + dr_mode = "host"; + vbus-supply = <&usb_vbus>; + phys = <&usb_phy 0>; + phy-names = "usb-phy"; + + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt index 2c30a5479069..6c7c2bce6d0c 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.txt +++ b/Documentation/devicetree/bindings/usb/dwc2.txt @@ -12,6 +12,7 @@ Required properties: - "lantiq,xrx200-usb": The DWC2 USB controller instance in Lantiq XRX SoCs; - "amlogic,meson8b-usb": The DWC2 USB controller instance in Amlogic Meson8b SoCs; - "amlogic,meson-gxbb-usb": The DWC2 USB controller instance in Amlogic S905 SoCs; + - "amcc,dwc-otg": The DWC2 USB controller instance in AMCC Canyonlands 460EX SoCs; - snps,dwc2: A generic DWC2 USB controller with default parameters. - reg : Should contain 1 register range (address and length) - interrupts : Should contain 1 interrupt @@ -25,11 +26,13 @@ Optional properties: Refer to phy/phy-bindings.txt for generic phy consumer properties - dr_mode: shall be one of "host", "peripheral" and "otg" Refer to usb/generic.txt -- g-use-dma: enable dma usage in gadget driver. - g-rx-fifo-size: size of rx fifo size in gadget mode. - g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget mode. - g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode. +Deprecated properties: +- g-use-dma: gadget DMA mode is automatically detected + Example: usb@101c0000 { diff --git a/Documentation/devicetree/bindings/usb/dwc3-st.txt b/Documentation/devicetree/bindings/usb/dwc3-st.txt index 01c71b1258f4..50dee3b44665 100644 --- a/Documentation/devicetree/bindings/usb/dwc3-st.txt +++ b/Documentation/devicetree/bindings/usb/dwc3-st.txt @@ -20,10 +20,10 @@ See: Documentation/devicetree/bindings/reset/reset.txt with 'reg' property - pinctl-names : A pinctrl state named "default" must be defined -See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt +See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt - pinctrl-0 : Pin control group -See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt +See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt - ranges : allows valid 1:1 translation between child's address space and parent's address space diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index e3e6983288e3..f658f394c2d3 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -56,6 +56,10 @@ Optional properties: - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated. + - in addition all properties from usb-xhci.txt from the current directory are + supported as well + + This is usually a subnode to DWC3 glue to which it is connected. dwc3@4a030000 { diff --git a/Documentation/devicetree/bindings/usb/ehci-omap.txt b/Documentation/devicetree/bindings/usb/ehci-omap.txt index 3dc231c832b0..d77e11a975a2 100644 --- a/Documentation/devicetree/bindings/usb/ehci-omap.txt +++ b/Documentation/devicetree/bindings/usb/ehci-omap.txt @@ -29,4 +29,3 @@ usbhsehci: ehci@4a064c00 { &usbhsehci { phys = <&hsusb1_phy 0 &hsusb3_phy>; }; - diff --git a/Documentation/devicetree/bindings/usb/ehci-st.txt b/Documentation/devicetree/bindings/usb/ehci-st.txt index fb45fa5770bb..410d922cfdd7 100644 --- a/Documentation/devicetree/bindings/usb/ehci-st.txt +++ b/Documentation/devicetree/bindings/usb/ehci-st.txt @@ -7,7 +7,7 @@ Required properties: - interrupts : one EHCI interrupt should be described here - pinctrl-names : a pinctrl state named "default" must be defined - pinctrl-0 : phandle referencing pin configuration of the USB controller -See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt +See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt - clocks : phandle list of usb clocks - clock-names : should be "ic" for interconnect clock and "clk48" See: Documentation/devicetree/bindings/clock/clock-bindings.txt diff --git a/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt b/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt new file mode 100644 index 000000000000..1d7c3bc677f7 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt @@ -0,0 +1,87 @@ +The device node for Mediatek USB3.0 DRD controller + +Required properties: + - compatible : should be "mediatek,mt8173-mtu3" + - reg : specifies physical base address and size of the registers + - reg-names: should be "mac" for device IP and "ippc" for IP port control + - interrupts : interrupt used by the device IP + - power-domains : a phandle to USB power domain node to control USB's + mtcmos + - vusb33-supply : regulator of USB avdd3.3v + - clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock-names + - clock-names : must contain "sys_ck" and "ref_ck" for clock of controller; + "wakeup_deb_p0" and "wakeup_deb_p1" are optional, they are + depends on "mediatek,enable-wakeup" + - phys : a list of phandle + phy specifier pairs + - dr_mode : should be one of "host", "peripheral" or "otg", + refer to usb/generic.txt + +Optional properties: + - #address-cells, #size-cells : should be '2' if the device has sub-nodes + with 'reg' property + - ranges : allows valid 1:1 translation between child's address space and + parent's address space + - extcon : external connector for vbus and idpin changes detection, needed + when supports dual-role mode. + - vbus-supply : reference to the VBUS regulator, needed when supports + dual-role mode. + - pinctl-names : a pinctrl state named "default" must be defined, + "id_float" and "id_ground" are optinal which depends on + "mediatek,enable-manual-drd" + - pinctrl-0 : pin control group + See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + + - maximum-speed : valid arguments are "super-speed", "high-speed" and + "full-speed"; refer to usb/generic.txt + - enable-manual-drd : supports manual dual-role switch via debugfs; usually + used when receptacle is TYPE-A and also wants to support dual-role + mode. + - mediatek,enable-wakeup : supports ip sleep wakeup used by host mode + - mediatek,syscon-wakeup : phandle to syscon used to access USB wakeup + control register, it depends on "mediatek,enable-wakeup". + +Sub-nodes: +The xhci should be added as subnode to mtu3 as shown in the following example +if host mode is enabled. The DT binding details of xhci can be found in: +Documentation/devicetree/bindings/usb/mt8173-xhci.txt + +Example: +ssusb: usb@11271000 { + compatible = "mediatek,mt8173-mtu3"; + reg = <0 0x11271000 0 0x3000>, + <0 0x11280700 0 0x0100>; + reg-names = "mac", "ippc"; + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>; + phys = <&phy_port0 PHY_TYPE_USB3>, + <&phy_port1 PHY_TYPE_USB2>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>, + <&pericfg CLK_PERI_USB0>, + <&pericfg CLK_PERI_USB1>; + clock-names = "sys_ck", "ref_ck", + "wakeup_deb_p0", + "wakeup_deb_p1"; + vusb33-supply = <&mt6397_vusb_reg>; + vbus-supply = <&usb_p0_vbus>; + extcon = <&extcon_usb>; + dr_mode = "otg"; + mediatek,enable-wakeup; + mediatek,syscon-wakeup = <&pericfg>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + + usb_host: xhci@11270000 { + compatible = "mediatek,mt8173-xhci"; + reg = <0 0x11270000 0 0x1000>; + reg-names = "mac"; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; + clock-names = "sys_ck", "ref_ck"; + vusb33-supply = <&mt6397_vusb_reg>; + status = "disabled"; + }; +}; diff --git a/Documentation/devicetree/bindings/usb/mt8173-xhci.txt b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt index b3a7ffa48852..0acfc8acbea1 100644 --- a/Documentation/devicetree/bindings/usb/mt8173-xhci.txt +++ b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt @@ -2,10 +2,18 @@ MT8173 xHCI The device node for Mediatek SOC USB3.0 host controller +There are two scenarios: the first one only supports xHCI driver; +the second one supports dual-role mode, and the host is based on xHCI +driver. Take account of backward compatibility, we divide bindings +into two parts. + +1st: only supports xHCI driver +------------------------------------------------------------------------ + Required properties: - compatible : should contain "mediatek,mt8173-xhci" - - reg : specifies physical base address and size of the registers, - the first one for MAC, the second for IPPC + - reg : specifies physical base address and size of the registers + - reg-names: should be "mac" for xHCI MAC and "ippc" for IP port control - interrupts : interrupt used by the controller - power-domains : a phandle to USB power domain node to control USB's mtcmos @@ -15,6 +23,7 @@ Required properties: entry in clock-names - clock-names : must contain "sys_ck": for clock of xHCI MAC + "ref_ck": for reference clock of xHCI MAC "wakeup_deb_p0": for USB wakeup debounce clock of port0 "wakeup_deb_p1": for USB wakeup debounce clock of port1 @@ -27,18 +36,22 @@ Optional properties: control register, it depends on "mediatek,wakeup-src". - vbus-supply : reference to the VBUS regulator; - usb3-lpm-capable : supports USB3.0 LPM + - pinctrl-names : a pinctrl state named "default" must be defined + - pinctrl-0 : pin control group + See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt Example: usb30: usb@11270000 { compatible = "mediatek,mt8173-xhci"; reg = <0 0x11270000 0 0x1000>, <0 0x11280700 0 0x0100>; + reg-names = "mac", "ippc"; interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; - clocks = <&topckgen CLK_TOP_USB30_SEL>, + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>, <&pericfg CLK_PERI_USB0>, <&pericfg CLK_PERI_USB1>; - clock-names = "sys_ck", + clock-names = "sys_ck", "ref_ck", "wakeup_deb_p0", "wakeup_deb_p1"; phys = <&phy_port0 PHY_TYPE_USB3>, @@ -49,3 +62,42 @@ usb30: usb@11270000 { mediatek,syscon-wakeup = <&pericfg>; mediatek,wakeup-src = <1>; }; + +2nd: dual-role mode with xHCI driver +------------------------------------------------------------------------ + +In the case, xhci is added as subnode to mtu3. An example and the DT binding +details of mtu3 can be found in: +Documentation/devicetree/bindings/usb/mt8173-mtu3.txt + +Required properties: + - compatible : should contain "mediatek,mt8173-xhci" + - reg : specifies physical base address and size of the registers + - reg-names: should be "mac" for xHCI MAC + - interrupts : interrupt used by the host controller + - power-domains : a phandle to USB power domain node to control USB's + mtcmos + - vusb33-supply : regulator of USB avdd3.3v + + - clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock-names + - clock-names : must be + "sys_ck": for clock of xHCI MAC + "ref_ck": for reference clock of xHCI MAC + +Optional properties: + - vbus-supply : reference to the VBUS regulator; + - usb3-lpm-capable : supports USB3.0 LPM + +Example: +usb30: usb@11270000 { + compatible = "mediatek,mt8173-xhci"; + reg = <0 0x11270000 0 0x1000>; + reg-names = "mac"; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; + clock-names = "sys_ck", "ref_ck"; + vusb33-supply = <&mt6397_vusb_reg>; + usb3-lpm-capable; +}; diff --git a/Documentation/devicetree/bindings/usb/ohci-da8xx.txt b/Documentation/devicetree/bindings/usb/ohci-da8xx.txt new file mode 100644 index 000000000000..2dc8f67eda39 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ohci-da8xx.txt @@ -0,0 +1,23 @@ +DA8XX USB OHCI controller + +Required properties: + + - compatible: Should be "ti,da830-ohci" + - reg: Should contain one register range i.e. start and length + - interrupts: Description of the interrupt line + - phys: Phandle for the PHY device + - phy-names: Should be "usb-phy" + +Optional properties: + - vbus-supply: phandle of regulator that controls vbus power / over-current + +Example: + +ohci: usb@0225000 { + compatible = "ti,da830-ohci"; + reg = <0x225000 0x1000>; + interrupts = <59>; + phys = <&usb_phy 1>; + phy-names = "usb-phy"; + vbus-supply = <®_usb_ohci>; +}; diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt index 39acb084bce9..73cc0963e823 100644 --- a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt +++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt @@ -18,7 +18,7 @@ A child node must exist to represent the core DWC3 IP block. The name of the node is not important. The content of the node is defined in dwc3.txt. Phy documentation is provided in the following places: -Documentation/devicetree/bindings/phy/qcom,dwc3-usb-phy.txt +Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt Example device nodes: diff --git a/Documentation/devicetree/bindings/usb/s3c2410-usb.txt b/Documentation/devicetree/bindings/usb/s3c2410-usb.txt new file mode 100644 index 000000000000..e45b38ce2986 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/s3c2410-usb.txt @@ -0,0 +1,22 @@ +Samsung S3C2410 and compatible SoC USB controller + +OHCI + +Required properties: + - compatible: should be "samsung,s3c2410-ohci" for USB host controller + - reg: address and lenght of the controller memory mapped region + - interrupts: interrupt number for the USB OHCI controller + - clocks: Should reference the bus and host clocks + - clock-names: Should contain two strings + "usb-bus-host" for the USB bus clock + "usb-host" for the USB host clock + +Example: + +usb0: ohci@49000000 { + compatible = "samsung,s3c2410-ohci"; + reg = <0x49000000 0x100>; + interrupts = <0 0 26 3>; + clocks = <&clocks UCLK>, <&clocks HCLK_USBH>; + clock-names = "usb-bus-host", "usb-host"; +}; diff --git a/Documentation/devicetree/bindings/usb/ulpi.txt b/Documentation/devicetree/bindings/usb/ulpi.txt new file mode 100644 index 000000000000..ca179dc4bd50 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ulpi.txt @@ -0,0 +1,20 @@ +ULPI bus binding +---------------- + +Phys that are behind a ULPI connection can be described with the following +binding. The host controller shall have a "ulpi" named node as a child, and +that node shall have one enabled node underneath it representing the ulpi +device on the bus. + +EXAMPLE +------- + +usb { + compatible = "vendor,usb-controller"; + + ulpi { + phy { + compatible = "vendor,phy"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt index 966885c636d0..2d80b60eeabe 100644 --- a/Documentation/devicetree/bindings/usb/usb-xhci.txt +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -11,6 +11,7 @@ Required properties: - "renesas,xhci-r8a7791" for r8a7791 SoC - "renesas,xhci-r8a7793" for r8a7793 SoC - "renesas,xhci-r8a7795" for r8a7795 SoC + - "renesas,xhci-r8a7796" for r8a7796 SoC - "renesas,rcar-gen2-xhci" for a generic R-Car Gen2 compatible device - "renesas,rcar-gen3-xhci" for a generic R-Car Gen3 compatible device - "xhci-platform" (deprecated) @@ -26,6 +27,7 @@ Required properties: Optional properties: - clocks: reference to a clock - usb3-lpm-capable: determines if platform is USB3 LPM capable + - quirk-broken-port-ped: set if the controller has broken port disable mechanism Example: usb@f0931000 { diff --git a/Documentation/devicetree/bindings/usb/usb251xb.txt b/Documentation/devicetree/bindings/usb/usb251xb.txt new file mode 100644 index 000000000000..0c065f77658f --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb251xb.txt @@ -0,0 +1,83 @@ +Microchip USB 2.0 Hi-Speed Hub Controller + +The device node for the configuration of a Microchip USB251xB/xBi USB 2.0 +Hi-Speed Controller. + +Required properties : + - compatible : Should be "microchip,usb251xb" or one of the specific types: + "microchip,usb2512b", "microchip,usb2512bi", "microchip,usb2513b", + "microchip,usb2513bi", "microchip,usb2514b", "microchip,usb2514bi" + - hub-reset-gpios : Should specify the gpio for hub reset + +Optional properties : + - reg : I2C address on the selected bus (default is <0x2C>) + - skip-config : Skip Hub configuration, but only send the USB-Attach command + - vendor-id : USB Vendor ID of the hub (16 bit, default is 0x0424) + - product-id : USB Product ID of the hub (16 bit, default depends on type) + - device-id : USB Device ID of the hub (16 bit, default is 0x0bb3) + - language-id : USB Language ID (16 bit, default is 0x0000) + - manufacturer : USB Manufacturer string (max 31 characters long) + - product : USB Product string (max 31 characters long) + - serial : USB Serial string (max 31 characters long) + - {bus,self}-powered : selects between self- and bus-powered operation (default + is self-powered) + - disable-hi-speed : disable USB Hi-Speed support + - {multi,single}-tt : selects between multi- and single-transaction-translator + (default is multi-tt) + - disable-eop : disable End of Packet generation in full-speed mode + - {ganged,individual}-sensing : select over-current sense type in self-powered + mode (default is individual) + - {ganged,individual}-port-switching : select port power switching mode + (default is individual) + - dynamic-power-switching : enable auto-switching from self- to bus-powered + operation if the local power source is removed or unavailable + - oc-delay-{100us,4ms,8ms,16ms} : set over current timer delay (default is 8ms) + - compound-device : indicated the hub is part of a compound device + - port-mapping-mode : enable port mapping mode + - string-support : enable string descriptor support (required for manufacturer, + product and serial string configuration) + - non-removable-ports : Should specify the ports which have a non-removable + device connected. + - sp-disabled-ports : Specifies the ports which will be self-power disabled + - bp-disabled-ports : Specifies the ports which will be bus-power disabled + - max-sp-power : Specifies the maximum current the hub consumes from an + upstream port when operating as self-powered hub including the power + consumption of a permanently attached peripheral if the hub is + configured as a compound device. The value is given in mA in a 0 - 500 + range (default is 2). + - max-bp-power : Specifies the maximum current the hub consumes from an + upstream port when operating as bus-powered hub including the power + consumption of a permanently attached peripheral if the hub is + configured as a compound device. The value is given in mA in a 0 - 500 + range (default is 100). + - max-sp-current : Specifies the maximum current the hub consumes from an + upstream port when operating as self-powered hub EXCLUDING the power + consumption of a permanently attached peripheral if the hub is + configured as a compound device. The value is given in mA in a 0 - 500 + range (default is 2). + - max-bp-current : Specifies the maximum current the hub consumes from an + upstream port when operating as bus-powered hub EXCLUDING the power + consumption of a permanently attached peripheral if the hub is + configured as a compound device. The value is given in mA in a 0 - 500 + range (default is 100). + - power-on-time : Specifies the time it takes from the time the host initiates + the power-on sequence to a port until the port has adequate power. The + value is given in ms in a 0 - 510 range (default is 100ms). + +Examples: + usb2512b@2c { + compatible = "microchip,usb2512b"; + hub-reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + }; + + usb2514b@2c { + compatible = "microchip,usb2514b"; + reg = <0x2c>; + reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + vendor-id = /bits/ 16 <0x0000>; + product-id = /bits/ 16 <0x0000>; + string-support; + manufacturer = "Foo"; + product = "Foo-Bar"; + serial = "1234567890A"; + }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index f0a48ea78659..ec0bfb9bbebd 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -24,9 +24,11 @@ ampire Ampire Co., Ltd. ams AMS AG amstaos AMS-Taos Inc. analogix Analogix Semiconductor, Inc. +andestech Andes Technology Corporation apm Applied Micro Circuits Corporation (APM) aptina Aptina Imaging arasan Arasan Chip Systems +aries Aries Embedded GmbH arm ARM Ltd. armadeus ARMadeus Systems SARL arrow Arrow Electronics @@ -38,7 +40,9 @@ atmel Atmel Corporation auo AU Optronics Corporation auvidea Auvidea GmbH avago Avago Technologies +avia avia semiconductor avic Shanghai AVIC Optoelectronics Co., Ltd. +axentia Axentia Technologies AB axis Axis Communications AB boe BOE Technology Group Co., Ltd. bosch Bosch Sensortec GmbH @@ -67,10 +71,12 @@ creative Creative Technology Ltd crystalfontz Crystalfontz America, Inc. cubietech Cubietech, Ltd. cypress Cypress Semiconductor Corporation +cznic CZ.NIC, z.s.p.o. dallas Maxim Integrated Products (formerly Dallas Semiconductor) davicom DAVICOM Semiconductor, Inc. delta Delta Electronics, Inc. denx Denx Software Engineering +devantech Devantech, Ltd. digi Digi International Inc. digilent Diglent, Inc. dlg Dialog Semiconductor @@ -98,11 +104,13 @@ everest Everest Semiconductor Co. Ltd. everspin Everspin Technologies, Inc. excito Excito ezchip EZchip Semiconductor +faraday Faraday Technology Corporation fcs Fairchild Semiconductor firefly Firefly focaltech FocalTech Systems Co.,Ltd friendlyarm Guangzhou FriendlyARM Computer Tech Co., Ltd fsl Freescale Semiconductor +fujitsu Fujitsu Ltd. ge General Electric Company geekbuying GeekBuying gef GE Fanuc Intelligent Platforms Embedded Systems, Inc. @@ -114,6 +122,7 @@ gmt Global Mixed-mode Technology, Inc. goodix Shenzhen Huiding Technology Co., Ltd. google Google, Inc. grinn Grinn +grmn Garmin Limited gumstix Gumstix, Inc. gw Gateworks Corporation hannstar HannStar Display Corporation @@ -126,6 +135,7 @@ hitex Hitex Development Tools holt Holt Integrated Circuits, Inc. honeywell Honeywell hp Hewlett Packard +holtek Holtek Semiconductor, Inc. i2se I2SE GmbH ibm International Business Machines (IBM) idt Integrated Device Technologies, Inc. @@ -135,6 +145,7 @@ infineon Infineon Technologies inforce Inforce Computing ingenic Ingenic Semiconductor innolux Innolux Corporation +inside-secure INSIDE Secure intel Intel Corporation intercontrol Inter Control Group invensense InvenSense Inc. @@ -153,23 +164,30 @@ kosagi Sutajio Ko-Usagi PTE Ltd. kyo Kyocera Corporation lacie LaCie lantiq Lantiq Semiconductor +lego LEGO Systems A/S lenovo Lenovo Group Ltd. lg LG Corporation +licheepi Lichee Pi linux Linux-specific binding lltc Linear Technology Corporation lsi LSI Corp. (LSI Logic) +lwn Liebherr-Werk Nenzing GmbH +macnica Macnica Americas marvell Marvell Technology Group Ltd. maxim Maxim Integrated Products +mcube mCube meas Measurement Specialties mediatek MediaTek Inc. melexis Melexis N.V. melfas MELFAS Inc. +memsic MEMSIC Inc. merrii Merrii Technology Co., Ltd. micrel Micrel Inc. microchip Microchip Technology Inc. microcrystal Micro Crystal AG micron Micron Technology Inc. minix MINIX Technology Ltd. +miramems MiraMEMS Sensing Technology Co., Ltd. mitsubishi Mitsubishi Electric Corporation mosaixtech Mosaix Technologies, Inc. moxa Moxa @@ -177,22 +195,29 @@ mpl MPL AG mqmaker mqmaker Inc. msi Micro-Star International Co. Ltd. mti Imagination Technologies Ltd. (formerly MIPS Technologies Inc.) +multi-inno Multi-Inno Technology Co.,Ltd mundoreader Mundo Reader S.L. murata Murata Manufacturing Co., Ltd. mxicy Macronix International Co., Ltd. +myir MYIR Tech Limited national National Semiconductor nec NEC LCD Technologies, Ltd. neonode Neonode Inc. netgear NETGEAR netlogic Broadcom Corporation (formerly NetLogic Microsystems) +netron-dy Netron DY netxeon Shenzhen Netxeon Technology CO., LTD +nexbox Nexbox newhaven Newhaven Display International +ni National Instruments nintendo Nintendo nokia Nokia nuvoton Nuvoton Technology Corporation +nvd New Vision Display nvidia NVIDIA nxp NXP Semiconductors okaya Okaya Electric America, Inc. +oki Oki Electric Industry Co., Ltd. olimex OLIMEX Ltd. onion Onion Corporation onnn ON Semiconductor Corp. @@ -208,9 +233,11 @@ parade Parade Technologies Inc. pericom Pericom Technology Inc. phytec PHYTEC Messtechnik GmbH picochip Picochip Ltd +pine64 Pine64 pixcir PIXCIR MICROELECTRONICS Co., Ltd plathome Plat'Home Co., Ltd. plda PLDA +poslab Poslab Technology Co., Ltd. powervr PowerVR (deprecated, use img) pulsedlight PulsedLight, Inc qca Qualcomm Atheros, Inc. @@ -229,8 +256,10 @@ realtek Realtek Semiconductor Corp. renesas Renesas Electronics Corporation richtek Richtek Technology Corporation ricoh Ricoh Co. Ltd. +rikomagic Rikomagic Tech Corp. Ltd rockchip Fuzhou Rockchip Electronics Co., Ltd samsung Samsung Semiconductor +samtec Samtec/Softing company sandisk Sandisk Corporation sbs Smart Battery System schindler Schindler @@ -275,8 +304,10 @@ tcg Trusted Computing Group tcl Toby Churchill Ltd. technexion TechNexion technologic Technologic Systems +terasic Terasic Inc. thine THine Electronics, Inc. ti Texas Instruments +tianma Tianma Micro-electronics Co., Ltd. tlm Trusted Logic Mobility topeet Topeet toradex Toradex AG @@ -289,6 +320,7 @@ tronfy Tronfy tronsmart Tronsmart truly Truly Semiconductors Limited tyan Tyan Computer Corporation +udoo Udoo uniwest United Western Technologies Corp (UniWest) upisemi uPI Semiconductor Corp. urt United Radiant Technology Corporation @@ -300,6 +332,7 @@ virtio Virtual I/O Device Specification, developed by the OASIS consortium vivante Vivante Corporation voipac Voipac Technologies s.r.o. wd Western Digital Corp. +wetek WeTek Electronics, limited. wexler Wexler winbond Winbond Electronics corp. wlf Wolfson Microelectronics @@ -308,7 +341,9 @@ x-powers X-Powers xes Extreme Engineering Solutions (X-ES) xillybus Xillybus Ltd. xlnx Xilinx +xunlong Shenzhen Xunlong Software CO.,Limited zarlink Zarlink Semiconductor +zeitec ZEITEC Semiconductor Co., LTD. zii Zodiac Inflight Innovations zte ZTE Corp. zyxel ZyXEL Communications Corp. diff --git a/Documentation/devicetree/bindings/watchdog/cortina,gemin-watchdog.txt b/Documentation/devicetree/bindings/watchdog/cortina,gemin-watchdog.txt new file mode 100644 index 000000000000..bc4b865d178b --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/cortina,gemin-watchdog.txt @@ -0,0 +1,17 @@ +Cortina Systems Gemini SoC Watchdog + +Required properties: +- compatible : must be "cortina,gemini-watchdog" +- reg : shall contain base register location and length +- interrupts : shall contain the interrupt for the watchdog + +Optional properties: +- timeout-sec : the default watchdog timeout in seconds. + +Example: + +watchdog@41000000 { + compatible = "cortina,gemini-watchdog"; + reg = <0x41000000 0x1000>; + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt index 8f3d96af81d7..1f6e101e299a 100644 --- a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt @@ -6,10 +6,11 @@ occurred. Required properties: - compatible : should be one among the following - (a) "samsung,s3c2410-wdt" for Exynos4 and previous SoCs - (b) "samsung,exynos5250-wdt" for Exynos5250 - (c) "samsung,exynos5420-wdt" for Exynos5420 - (c) "samsung,exynos7-wdt" for Exynos7 + - "samsung,s3c2410-wdt" for S3C2410 + - "samsung,s3c6410-wdt" for S3C6410, S5PV210 and Exynos4 + - "samsung,exynos5250-wdt" for Exynos5250 + - "samsung,exynos5420-wdt" for Exynos5420 + - "samsung,exynos7-wdt" for Exynos7 - reg : base physical address of the controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt b/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt new file mode 100644 index 000000000000..06ce67766756 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt @@ -0,0 +1,32 @@ +ZTE zx2967 Watchdog timer + +Required properties: + +- compatible : should be one of the following. + * zte,zx296718-wdt +- reg : Specifies base physical address and size of the registers. +- clocks : Pairs of phandle and specifier referencing the controller's clocks. +- resets : Reference to the reset controller controlling the watchdog + controller. + +Optional properties: + +- timeout-sec : Contains the watchdog timeout in seconds. +- zte,wdt-reset-sysctrl : Directs how to reset system by the watchdog. + if we don't want to restart system when watchdog been triggered, + it's not required, vice versa. + It should include following fields. + * phandle of aon-sysctrl. + * offset of register that be written, should be 0xb0. + * configure value that be written to aon-sysctrl. + * bit mask, corresponding bits will be affected. + +Example: + +wdt: watchdog@1465000 { + compatible = "zte,zx296718-wdt"; + reg = <0x1465000 0x1000>; + clocks = <&topcrm WDT_WCLK>; + resets = <&toprst 35>; + zte,wdt-reset-sysctrl = <&aon_sysctrl 0xb0 1 0x115>; +}; |