diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
657 files changed, 19754 insertions, 7206 deletions
diff --git a/Documentation/devicetree/bindings/Makefile b/Documentation/devicetree/bindings/Makefile index 8a2774b5834b..5138a2f6232a 100644 --- a/Documentation/devicetree/bindings/Makefile +++ b/Documentation/devicetree/bindings/Makefile @@ -19,13 +19,15 @@ quiet_cmd_mk_schema = SCHEMA $@ DT_DOCS = $(shell \ cd $(srctree)/$(src) && \ - find * \( -name '*.yaml' ! -name $(DT_TMP_SCHEMA) \) \ + find * \( -name '*.yaml' ! \ + -name $(DT_TMP_SCHEMA) ! \ + -name '*.example.dt.yaml' \) \ ) DT_SCHEMA_FILES ?= $(addprefix $(src)/,$(DT_DOCS)) extra-y += $(patsubst $(src)/%.yaml,%.example.dts, $(DT_SCHEMA_FILES)) -extra-y += $(patsubst $(src)/%.yaml,%.example.dtb, $(DT_SCHEMA_FILES)) +extra-y += $(patsubst $(src)/%.yaml,%.example.dt.yaml, $(DT_SCHEMA_FILES)) $(obj)/$(DT_TMP_SCHEMA): $(DT_SCHEMA_FILES) FORCE $(call if_changed,mk_schema) diff --git a/Documentation/devicetree/bindings/arm/actions.txt b/Documentation/devicetree/bindings/arm/actions.txt deleted file mode 100644 index d54f33c4e0da..000000000000 --- a/Documentation/devicetree/bindings/arm/actions.txt +++ /dev/null @@ -1,56 +0,0 @@ -Actions Semi platforms device tree bindings -------------------------------------------- - - -S500 SoC -======== - -Required root node properties: - - - compatible : must contain "actions,s500" - - -Modules: - -Root node property compatible must contain, depending on module: - - - LeMaker Guitar: "lemaker,guitar" - - -Boards: - -Root node property compatible must contain, depending on board: - - - Allo.com Sparky: "allo,sparky" - - Cubietech CubieBoard6: "cubietech,cubieboard6" - - LeMaker Guitar Base Board rev. B: "lemaker,guitar-bb-rev-b", "lemaker,guitar" - - -S700 SoC -======== - -Required root node properties: - -- compatible : must contain "actions,s700" - - -Boards: - -Root node property compatible must contain, depending on board: - - - Cubietech CubieBoard7: "cubietech,cubieboard7" - - -S900 SoC -======== - -Required root node properties: - -- compatible : must contain "actions,s900" - - -Boards: - -Root node property compatible must contain, depending on board: - - - uCRobotics Bubblegum-96: "ucrobotics,bubblegum-96" diff --git a/Documentation/devicetree/bindings/arm/actions.yaml b/Documentation/devicetree/bindings/arm/actions.yaml new file mode 100644 index 000000000000..ace3fdaa8396 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/actions.yaml @@ -0,0 +1,38 @@ +# SPDX-License-Identifier: GPL-2.0-or-later OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/actions.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Actions Semi platforms device tree bindings + +maintainers: + - Andreas Färber <afaerber@suse.de> + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + +properties: + compatible: + oneOf: + # The Actions Semi S500 is a quad-core ARM Cortex-A9 SoC. + - items: + - enum: + - allo,sparky # Allo.com Sparky + - cubietech,cubieboard6 # Cubietech CubieBoard6 + - const: actions,s500 + - items: + - enum: + - lemaker,guitar-bb-rev-b # LeMaker Guitar Base Board rev. B + - const: lemaker,guitar + - const: actions,s500 + + # The Actions Semi S700 is a quad-core ARM Cortex-A53 SoC. + - items: + - enum: + - cubietech,cubieboard7 # Cubietech CubieBoard7 + - const: actions,s700 + + # The Actions Semi S900 is a quad-core ARM Cortex-A53 SoC. + - items: + - enum: + - ucrobotics,bubblegum-96 # uCRobotics Bubblegum-96 + - const: actions,s900 diff --git a/Documentation/devicetree/bindings/arm/al,alpine.txt b/Documentation/devicetree/bindings/arm/al,alpine.txt deleted file mode 100644 index d00debe2e86f..000000000000 --- a/Documentation/devicetree/bindings/arm/al,alpine.txt +++ /dev/null @@ -1,16 +0,0 @@ -Annapurna Labs Alpine Platform Device Tree Bindings ---------------------------------------------------------------- - -Boards in the Alpine family shall have the following properties: - -* Required root node properties: -compatible: must contain "al,alpine" - -* Example: - -/ { - model = "Annapurna Labs Alpine Dev Board"; - compatible = "al,alpine"; - - ... -} diff --git a/Documentation/devicetree/bindings/arm/al,alpine.yaml b/Documentation/devicetree/bindings/arm/al,alpine.yaml new file mode 100644 index 000000000000..a70dff277e05 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/al,alpine.yaml @@ -0,0 +1,21 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/al,alpine.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Annapurna Labs Alpine Platform Device Tree Bindings + +maintainers: + - Tsahee Zidenberg <tsahee@annapurnalabs.com> + - Antoine Tenart <antoine.tenart@bootlin.com> + +properties: + compatible: + items: + - const: al,alpine + model: + items: + - const: "Annapurna Labs Alpine Dev Board" + +... diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt deleted file mode 100644 index 061f7b98a07f..000000000000 --- a/Documentation/devicetree/bindings/arm/amlogic.txt +++ /dev/null @@ -1,142 +0,0 @@ -Amlogic MesonX device tree bindings -------------------------------------------- - -Work in progress statement: - -Device tree files and bindings applying to Amlogic SoCs and boards are -considered "unstable". Any Amlogic device tree binding may change at -any time. Be sure to use a device tree binary and a kernel image -generated from the same source tree. - -Please refer to Documentation/devicetree/bindings/ABI.txt for a definition of a -stable binding/ABI. - ---------------------------------------------------------------- - -Boards with the Amlogic Meson6 SoC shall have the following properties: - Required root node property: - compatible: "amlogic,meson6" - -Boards with the Amlogic Meson8 SoC shall have the following properties: - Required root node property: - compatible: "amlogic,meson8"; - -Boards with the Amlogic Meson8b SoC shall have the following properties: - Required root node property: - compatible: "amlogic,meson8b"; - -Boards with the Amlogic Meson8m2 SoC shall have the following properties: - Required root node property: - compatible: "amlogic,meson8m2"; - -Boards with the Amlogic Meson GXBaby SoC shall have the following properties: - Required root node property: - compatible: "amlogic,meson-gxbb"; - -Boards with the Amlogic Meson GXL S905X SoC shall have the following properties: - Required root node property: - compatible: "amlogic,s905x", "amlogic,meson-gxl"; - -Boards with the Amlogic Meson GXL S905D SoC shall have the following properties: - Required root node property: - compatible: "amlogic,s905d", "amlogic,meson-gxl"; - -Boards with the Amlogic Meson GXL S805X SoC shall have the following properties: - Required root node property: - compatible: "amlogic,s805x", "amlogic,meson-gxl"; - -Boards with the Amlogic Meson GXL S905W SoC shall have the following properties: - Required root node property: - compatible: "amlogic,s905w", "amlogic,meson-gxl"; - -Boards with the Amlogic Meson GXM S912 SoC shall have the following properties: - Required root node property: - compatible: "amlogic,s912", "amlogic,meson-gxm"; - -Boards with the Amlogic Meson AXG A113D SoC shall have the following properties: - Required root node property: - compatible: "amlogic,a113d", "amlogic,meson-axg"; - -Boards with the Amlogic Meson G12A S905D2 SoC shall have the following properties: - Required root node property: - compatible: "amlogic,g12a"; - -Board compatible values (alphabetically, grouped by SoC): - - - "geniatech,atv1200" (Meson6) - - - "minix,neo-x8" (Meson8) - - - "endless,ec100" (Meson8b) - - "hardkernel,odroid-c1" (Meson8b) - - "tronfy,mxq" (Meson8b) - - - "tronsmart,mxiii-plus" (Meson8m2) - - - "amlogic,p200" (Meson gxbb) - - "amlogic,p201" (Meson gxbb) - - "friendlyarm,nanopi-k2" (Meson gxbb) - - "hardkernel,odroid-c2" (Meson gxbb) - - "nexbox,a95x" (Meson gxbb or Meson gxl s905x) - - "tronsmart,vega-s95-pro", "tronsmart,vega-s95" (Meson gxbb) - - "tronsmart,vega-s95-meta", "tronsmart,vega-s95" (Meson gxbb) - - "tronsmart,vega-s95-telos", "tronsmart,vega-s95" (Meson gxbb) - - "wetek,hub" (Meson gxbb) - - "wetek,play2" (Meson gxbb) - - - "amlogic,p212" (Meson gxl s905x) - - "hwacom,amazetv" (Meson gxl s905x) - - "khadas,vim" (Meson gxl s905x) - - "libretech,cc" (Meson gxl s905x) - - - "amlogic,p230" (Meson gxl s905d) - - "amlogic,p231" (Meson gxl s905d) - - "phicomm,n1" (Meson gxl s905d) - - - "amlogic,p241" (Meson gxl s805x) - - "libretech,aml-s805x-ac" (Meson gxl s805x) - - - "amlogic,p281" (Meson gxl s905w) - - "oranth,tx3-mini" (Meson gxl s905w) - - - "amlogic,q200" (Meson gxm s912) - - "amlogic,q201" (Meson gxm s912) - - "khadas,vim2" (Meson gxm s912) - - "kingnovel,r-box-pro" (Meson gxm S912) - - "nexbox,a1" (Meson gxm s912) - - "tronsmart,vega-s96" (Meson gxm s912) - - - "amlogic,s400" (Meson axg a113d) - - - "amlogic,u200" (Meson g12a s905d2) - - "amediatech,x96-max" (Meson g12a s905x2) - - "seirobotics,sei510" (Meson g12a s905x2) - -Amlogic Meson Firmware registers Interface ------------------------------------------- - -The Meson SoCs have a register bank with status and data shared with the -secure firmware. - -Required properties: - - compatible: For Meson GX SoCs, must be "amlogic,meson-gx-ao-secure", "syscon" - -Properties should indentify components of this register interface : - -Meson GX SoC Information ------------------------- -A firmware register encodes the SoC type, package and revision information on -the Meson GX SoCs. -If present, the following property should be added : - -Optional properties: - - amlogic,has-chip-id: If present, the interface gives the current SoC version. - -Example -------- - -ao-secure@140 { - compatible = "amlogic,meson-gx-ao-secure", "syscon"; - reg = <0x0 0x140 0x0 0x140>; - amlogic,has-chip-id; -}; diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml new file mode 100644 index 000000000000..99015cef8bb1 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/amlogic.yaml @@ -0,0 +1,159 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/amlogic.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic MesonX device tree bindings + +maintainers: + - Kevin Hilman <khilman@baylibre.com> + +description: |+ + Work in progress statement: + + Device tree files and bindings applying to Amlogic SoCs and boards are + considered "unstable". Any Amlogic device tree binding may change at + any time. Be sure to use a device tree binary and a kernel image + generated from the same source tree. + + Please refer to Documentation/devicetree/bindings/ABI.txt for a definition of a + stable binding/ABI. + +properties: + $nodename: + const: '/' + compatible: + oneOf: + - description: Boards with the Amlogic Meson6 SoC + items: + - enum: + - geniatech,atv1200 + - const: amlogic,meson6 + + - description: Boards with the Amlogic Meson8 SoC + items: + - enum: + - minix,neo-x8 + - const: amlogic,meson8 + + - description: Boards with the Amlogic Meson8m2 SoC + items: + - enum: + - tronsmart,mxiii-plus + - const: amlogic,meson8m2 + + - description: Boards with the Amlogic Meson8b SoC + items: + - enum: + - endless,ec100 + - hardkernel,odroid-c1 + - tronfy,mxq + - const: amlogic,meson8b + + - description: Boards with the Amlogic Meson GXBaby SoC + items: + - enum: + - amlogic,p200 + - amlogic,p201 + - friendlyarm,nanopi-k2 + - hardkernel,odroid-c2 + - nexbox,a95x + - wetek,hub + - wetek,play2 + - const: amlogic,meson-gxbb + + - description: Tronsmart Vega S95 devices + items: + - enum: + - tronsmart,vega-s95-pro + - tronsmart,vega-s95-meta + - tronsmart,vega-s95-telos + - const: tronsmart,vega-s95 + - const: amlogic,meson-gxbb + + - description: Boards with the Amlogic Meson GXL S805X SoC + items: + - enum: + - amlogic,p241 + - libretech,aml-s805x-ac + - const: amlogic,s805x + - const: amlogic,meson-gxl + + - description: Boards with the Amlogic Meson GXL S905W SoC + items: + - enum: + - amlogic,p281 + - oranth,tx3-mini + - const: amlogic,s905w + - const: amlogic,meson-gxl + + - description: Boards with the Amlogic Meson GXL S905X SoC + items: + - enum: + - amlogic,p212 + - hwacom,amazetv + - khadas,vim + - libretech,cc + - nexbox,a95x + - const: amlogic,s905x + - const: amlogic,meson-gxl + + - description: Boards with the Amlogic Meson GXL S905D SoC + items: + - enum: + - amlogic,p230 + - amlogic,p231 + - phicomm,n1 + - const: amlogic,s905d + - const: amlogic,meson-gxl + + - description: Boards with the Amlogic Meson GXM S912 SoC + items: + - enum: + - amlogic,q200 + - amlogic,q201 + - khadas,vim2 + - kingnovel,r-box-pro + - nexbox,a1 + - tronsmart,vega-s96 + - const: amlogic,s912 + - const: amlogic,meson-gxm + + - description: Boards with the Amlogic Meson AXG A113D SoC + items: + - enum: + - amlogic,s400 + - const: amlogic,a113d + - const: amlogic,meson-axg + + - description: Boards with the Amlogic Meson G12A S905D2/X2/Y2 SoC + items: + - enum: + - amediatech,x96-max + - amlogic,u200 + - seirobotics,sei510 + - const: amlogic,g12a + + - description: Boards with the Amlogic Meson G12B A311D SoC + items: + - enum: + - khadas,vim3 + - const: amlogic,a311d + - const: amlogic,g12b + + - description: Boards with the Amlogic Meson G12B S922X SoC + items: + - enum: + - hardkernel,odroid-n2 + - khadas,vim3 + - const: amlogic,s922x + - const: amlogic,g12b + + - description: Boards with the Amlogic Meson SM1 S905X3/D3/Y3 SoC + items: + - enum: + - seirobotics,sei610 + - khadas,vim3l + - const: amlogic,sm1 +... diff --git a/Documentation/devicetree/bindings/arm/amlogic/amlogic,meson-gx-ao-secure.yaml b/Documentation/devicetree/bindings/arm/amlogic/amlogic,meson-gx-ao-secure.yaml new file mode 100644 index 000000000000..853d7d2b56f5 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/amlogic/amlogic,meson-gx-ao-secure.yaml @@ -0,0 +1,52 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 BayLibre, SAS +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/arm/amlogic/amlogic,meson-gx-ao-secure.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Amlogic Meson Firmware registers Interface + +maintainers: + - Neil Armstrong <narmstrong@baylibre.com> + +description: | + The Meson SoCs have a register bank with status and data shared with the + secure firmware. + +# We need a select here so we don't match all nodes with 'syscon' +select: + properties: + compatible: + contains: + const: amlogic,meson-gx-ao-secure + required: + - compatible + +properties: + compatible: + items: + - const: amlogic,meson-gx-ao-secure + - const: syscon + + reg: + maxItems: 1 + + amlogic,has-chip-id: + description: | + A firmware register encodes the SoC type, package and revision + information on the Meson GX SoCs. If present, the interface gives + the current SoC version. + type: boolean + +required: + - compatible + - reg + +examples: + - | + ao-secure@140 { + compatible = "amlogic,meson-gx-ao-secure", "syscon"; + reg = <0x140 0x140>; + amlogic,has-chip-id; + }; diff --git a/Documentation/devicetree/bindings/arm/arm,scmi.txt b/Documentation/devicetree/bindings/arm/arm,scmi.txt index 5f3719ab7075..083dbf96ee00 100644 --- a/Documentation/devicetree/bindings/arm/arm,scmi.txt +++ b/Documentation/devicetree/bindings/arm/arm,scmi.txt @@ -6,7 +6,7 @@ that are provided by the hardware platform it is running on, including power and performance functions. This binding is intended to define the interface the firmware implementing -the SCMI as described in ARM document number ARM DUI 0922B ("ARM System Control +the SCMI as described in ARM document number ARM DEN 0056A ("ARM System Control and Management Interface Platform Design Document")[0] provide for OSPM in the device tree. @@ -73,6 +73,16 @@ Required properties: as used by the firmware. Refer to platform details for your implementation for the IDs to use. +Reset signal bindings for the reset domains based on SCMI Message Protocol +------------------------------------------------------------ + +This binding for the SCMI reset domain providers uses the generic reset +signal binding[5]. + +Required properties: + - #reset-cells : Should be 1. Contains the reset domain ID value used + by SCMI commands. + SRAM and Shared Memory for SCMI ------------------------------- @@ -93,6 +103,7 @@ Required sub-node properties: [2] Documentation/devicetree/bindings/power/power_domain.txt [3] Documentation/devicetree/bindings/thermal/thermal.txt [4] Documentation/devicetree/bindings/sram/sram.txt +[5] Documentation/devicetree/bindings/reset/reset.txt Example: @@ -152,6 +163,11 @@ firmware { reg = <0x15>; #thermal-sensor-cells = <1>; }; + + scmi_reset: protocol@16 { + reg = <0x16>; + #reset-cells = <1>; + }; }; }; @@ -166,6 +182,7 @@ hdlcd@7ff60000 { reg = <0 0x7ff60000 0 0x1000>; clocks = <&scmi_clk 4>; power-domains = <&scmi_devpd 1>; + resets = <&scmi_reset 10>; }; thermal-zones { diff --git a/Documentation/devicetree/bindings/arm/arm-boards b/Documentation/devicetree/bindings/arm/arm-boards index abff8d834a6a..b2a9f9f8430b 100644 --- a/Documentation/devicetree/bindings/arm/arm-boards +++ b/Documentation/devicetree/bindings/arm/arm-boards @@ -197,9 +197,9 @@ Required nodes: The description for the board must include: - a "psci" node describing the boot method used for the secondary CPUs. A detailed description of the bindings used for "psci" nodes is present - in the psci.txt file. + in the psci.yaml file. - a "cpus" node describing the available cores and their associated - "enable-method"s. For more details see cpus.txt file. + "enable-method"s. For more details see cpus.yaml file. Example: diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt deleted file mode 100644 index 99dee23c74a4..000000000000 --- a/Documentation/devicetree/bindings/arm/atmel-at91.txt +++ /dev/null @@ -1,73 +0,0 @@ -Atmel AT91 device tree bindings. -================================ - -Boards with a SoC of the Atmel AT91 or SMART family shall have the following -properties: - -Required root node properties: -compatible: must be one of: - * "atmel,at91rm9200" - - * "atmel,at91sam9" for SoCs using an ARM926EJ-S core, shall be extended with - the specific SoC family or compatible: - o "atmel,at91sam9260" - o "atmel,at91sam9261" - o "atmel,at91sam9263" - o "atmel,at91sam9x5" for the 5 series, shall be extended with the specific - SoC compatible: - - "atmel,at91sam9g15" - - "atmel,at91sam9g25" - - "atmel,at91sam9g35" - - "atmel,at91sam9x25" - - "atmel,at91sam9x35" - o "atmel,at91sam9g20" - o "atmel,at91sam9g45" - o "atmel,at91sam9n12" - o "atmel,at91sam9rl" - o "atmel,at91sam9xe" - o "microchip,sam9x60" - * "atmel,sama5" for SoCs using a Cortex-A5, shall be extended with the specific - SoC family: - o "atmel,sama5d2" shall be extended with the specific SoC compatible: - - "atmel,sama5d27" - o "atmel,sama5d3" shall be extended with the specific SoC compatible: - - "atmel,sama5d31" - - "atmel,sama5d33" - - "atmel,sama5d34" - - "atmel,sama5d35" - - "atmel,sama5d36" - o "atmel,sama5d4" shall be extended with the specific SoC compatible: - - "atmel,sama5d41" - - "atmel,sama5d42" - - "atmel,sama5d43" - - "atmel,sama5d44" - - * "atmel,samv7" for MCUs using a Cortex-M7, shall be extended with the specific - SoC family: - o "atmel,sams70" shall be extended with the specific MCU compatible: - - "atmel,sams70j19" - - "atmel,sams70j20" - - "atmel,sams70j21" - - "atmel,sams70n19" - - "atmel,sams70n20" - - "atmel,sams70n21" - - "atmel,sams70q19" - - "atmel,sams70q20" - - "atmel,sams70q21" - o "atmel,samv70" shall be extended with the specific MCU compatible: - - "atmel,samv70j19" - - "atmel,samv70j20" - - "atmel,samv70n19" - - "atmel,samv70n20" - - "atmel,samv70q19" - - "atmel,samv70q20" - o "atmel,samv71" shall be extended with the specific MCU compatible: - - "atmel,samv71j19" - - "atmel,samv71j20" - - "atmel,samv71j21" - - "atmel,samv71n19" - - "atmel,samv71n20" - - "atmel,samv71n21" - - "atmel,samv71q19" - - "atmel,samv71q20" - - "atmel,samv71q21" diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.yaml b/Documentation/devicetree/bindings/arm/atmel-at91.yaml new file mode 100644 index 000000000000..6e168abcd4d1 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/atmel-at91.yaml @@ -0,0 +1,134 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/atmel-at91.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Atmel AT91 device tree bindings. + +maintainers: + - Alexandre Belloni <alexandre.belloni@bootlin.com> + - Ludovic Desroches <ludovic.desroches@microchip.com> + +description: | + Boards with a SoC of the Atmel AT91 or SMART family shall have the following + +properties: + $nodename: + const: '/' + compatible: + oneOf: + - items: + - const: atmel,at91rm9200 + - items: + - enum: + - olimex,sam9-l9260 + - enum: + - atmel,at91sam9260 + - atmel,at91sam9261 + - atmel,at91sam9263 + - atmel,at91sam9g20 + - atmel,at91sam9g45 + - atmel,at91sam9n12 + - atmel,at91sam9rl + - atmel,at91sam9xe + - atmel,at91sam9x60 + - const: atmel,at91sam9 + + - items: + - enum: + - atmel,at91sam9g15 + - atmel,at91sam9g25 + - atmel,at91sam9g35 + - atmel,at91sam9x25 + - atmel,at91sam9x35 + - const: atmel,at91sam9x5 + - const: atmel,at91sam9 + + - items: + - const: atmel,sama5d27 + - const: atmel,sama5d2 + - const: atmel,sama5 + + - description: Nattis v2 board with Natte v2 power board + items: + - const: axentia,nattis-2 + - const: axentia,natte-2 + - const: axentia,linea + - const: atmel,sama5d31 + - const: atmel,sama5d3 + - const: atmel,sama5 + + - description: TSE-850 v3 board + items: + - const: axentia,tse850v3 + - const: axentia,linea + - const: atmel,sama5d31 + - const: atmel,sama5d3 + - const: atmel,sama5 + + - items: + - const: axentia,linea + - const: atmel,sama5d31 + - const: atmel,sama5d3 + - const: atmel,sama5 + + - items: + - enum: + - atmel,sama5d31 + - atmel,sama5d33 + - atmel,sama5d34 + - atmel,sama5d35 + - atmel,sama5d36 + - const: atmel,sama5d3 + - const: atmel,sama5 + + - items: + - enum: + - atmel,sama5d41 + - atmel,sama5d42 + - atmel,sama5d43 + - atmel,sama5d44 + - const: atmel,sama5d4 + - const: atmel,sama5 + + - items: + - enum: + - atmel,sams70j19 + - atmel,sams70j20 + - atmel,sams70j21 + - atmel,sams70n19 + - atmel,sams70n20 + - atmel,sams70n21 + - atmel,sams70q19 + - atmel,sams70q20 + - atmel,sams70q21 + - const: atmel,sams70 + - const: atmel,samv7 + + - items: + - enum: + - atmel,samv70j19 + - atmel,samv70j20 + - atmel,samv70n19 + - atmel,samv70n20 + - atmel,samv70q19 + - atmel,samv70q20 + - const: atmel,samv70 + - const: atmel,samv7 + + - items: + - enum: + - atmel,samv71j19 + - atmel,samv71j20 + - atmel,samv71j21 + - atmel,samv71n19 + - atmel,samv71n20 + - atmel,samv71n21 + - atmel,samv71q19 + - atmel,samv71q20 + - atmel,samv71q21 + - const: atmel,samv71 + - const: atmel,samv7 + +... diff --git a/Documentation/devicetree/bindings/arm/axxia.txt b/Documentation/devicetree/bindings/arm/axxia.txt deleted file mode 100644 index 7b4ef9c07696..000000000000 --- a/Documentation/devicetree/bindings/arm/axxia.txt +++ /dev/null @@ -1,12 +0,0 @@ -Axxia AXM55xx device tree bindings - -Boards using the AXM55xx SoC need to have the following properties: - -Required root node property: - - - compatible = "lsi,axm5516" - -Boards: - - LSI AXM5516 Validation board (Amarillo) - compatible = "lsi,axm5516-amarillo", "lsi,axm5516" diff --git a/Documentation/devicetree/bindings/arm/axxia.yaml b/Documentation/devicetree/bindings/arm/axxia.yaml new file mode 100644 index 000000000000..98780a569f22 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/axxia.yaml @@ -0,0 +1,19 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/axxia.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Axxia AXM55xx device tree bindings + +maintainers: + - Anders Berg <anders.berg@lsi.com> + +properties: + compatible: + description: LSI AXM5516 Validation board (Amarillo) + items: + - const: lsi,axm5516-amarillo + - const: lsi,axm5516 + +... diff --git a/Documentation/devicetree/bindings/arm/coresight-cpu-debug.txt b/Documentation/devicetree/bindings/arm/coresight-cpu-debug.txt index 298291211ea4..f1de3247c1b7 100644 --- a/Documentation/devicetree/bindings/arm/coresight-cpu-debug.txt +++ b/Documentation/devicetree/bindings/arm/coresight-cpu-debug.txt @@ -26,8 +26,8 @@ Required properties: processor core is clocked by the internal CPU clock, so it is enabled with CPU clock by default. -- cpu : the CPU phandle the debug module is affined to. When omitted - the module is considered to belong to CPU0. +- cpu : the CPU phandle the debug module is affined to. Do not assume it + to default to CPU0 if omitted. Optional properties: diff --git a/Documentation/devicetree/bindings/arm/coresight.txt b/Documentation/devicetree/bindings/arm/coresight.txt index 8a88ddebc1a2..fcc3bacfd8bc 100644 --- a/Documentation/devicetree/bindings/arm/coresight.txt +++ b/Documentation/devicetree/bindings/arm/coresight.txt @@ -59,6 +59,11 @@ its hardware characteristcs. * port or ports: see "Graph bindings for Coresight" below. +* Additional required property for Embedded Trace Macrocell (version 3.x and + version 4.x): + * cpu: the cpu phandle this ETM/PTM is affined to. Do not + assume it to default to CPU0 if omitted. + * Additional required properties for System Trace Macrocells (STM): * reg: along with the physical base address and length of the register set as described above, another entry is required to describe the @@ -87,9 +92,6 @@ its hardware characteristcs. * arm,cp14: must be present if the system accesses ETM/PTM management registers via co-processor 14. - * cpu: the cpu phandle this ETM/PTM is affined to. When omitted the - source is considered to belong to CPU0. - * Optional property for TMC: * arm,buffer-size: size of contiguous buffer space for TMC ETR diff --git a/Documentation/devicetree/bindings/arm/cpus.yaml b/Documentation/devicetree/bindings/arm/cpus.yaml index 591bbd012d63..cb30895e3b67 100644 --- a/Documentation/devicetree/bindings/arm/cpus.yaml +++ b/Documentation/devicetree/bindings/arm/cpus.yaml @@ -39,281 +39,245 @@ description: |+ described below. properties: - $nodename: - const: cpus - description: Container of cpu nodes - - '#address-cells': - enum: [1, 2] + reg: + maxItems: 1 description: | - Definition depends on ARM architecture version and configuration: + Usage and definition depend on ARM architecture version and + configuration: On uniprocessor ARM architectures previous to v7 - value must be 1, to enable a simple enumeration - scheme for processors that do not have a HW CPU - identification register. - On 32-bit ARM 11 MPcore, ARM v7 or later systems - value must be 1, that corresponds to CPUID/MPIDR - registers sizes. - On ARM v8 64-bit systems value should be set to 2, - that corresponds to the MPIDR_EL1 register size. - If MPIDR_EL1[63:32] value is equal to 0 on all CPUs - in the system, #address-cells can be set to 1, since - MPIDR_EL1[63:32] bits are not used for CPUs - identification. - - '#size-cells': - const: 0 - -patternProperties: - '^cpu@[0-9a-f]+$': - type: object - properties: - device_type: - const: cpu - - reg: - maxItems: 1 - description: | - Usage and definition depend on ARM architecture version and - configuration: - - On uniprocessor ARM architectures previous to v7 - this property is required and must be set to 0. - - On ARM 11 MPcore based systems this property is - required and matches the CPUID[11:0] register bits. - - Bits [11:0] in the reg cell must be set to - bits [11:0] in CPU ID register. - - All other bits in the reg cell must be set to 0. - - On 32-bit ARM v7 or later systems this property is - required and matches the CPU MPIDR[23:0] register - bits. - - Bits [23:0] in the reg cell must be set to - bits [23:0] in MPIDR. - - All other bits in the reg cell must be set to 0. - - On ARM v8 64-bit systems this property is required - and matches the MPIDR_EL1 register affinity bits. + this property is required and must be set to 0. + + On ARM 11 MPcore based systems this property is + required and matches the CPUID[11:0] register bits. + + Bits [11:0] in the reg cell must be set to + bits [11:0] in CPU ID register. + + All other bits in the reg cell must be set to 0. + + On 32-bit ARM v7 or later systems this property is + required and matches the CPU MPIDR[23:0] register + bits. + + Bits [23:0] in the reg cell must be set to + bits [23:0] in MPIDR. + + All other bits in the reg cell must be set to 0. + + On ARM v8 64-bit systems this property is required + and matches the MPIDR_EL1 register affinity bits. + + * If cpus node's #address-cells property is set to 2 + + The first reg cell bits [7:0] must be set to + bits [39:32] of MPIDR_EL1. + + The second reg cell bits [23:0] must be set to + bits [23:0] of MPIDR_EL1. + + * If cpus node's #address-cells property is set to 1 + + The reg cell bits [23:0] must be set to bits [23:0] + of MPIDR_EL1. + + All other bits in the reg cells must be set to 0. + + compatible: + enum: + - arm,arm710t + - arm,arm720t + - arm,arm740t + - arm,arm7ej-s + - arm,arm7tdmi + - arm,arm7tdmi-s + - arm,arm9es + - arm,arm9ej-s + - arm,arm920t + - arm,arm922t + - arm,arm925 + - arm,arm926e-s + - arm,arm926ej-s + - arm,arm940t + - arm,arm946e-s + - arm,arm966e-s + - arm,arm968e-s + - arm,arm9tdmi + - arm,arm1020e + - arm,arm1020t + - arm,arm1022e + - arm,arm1026ej-s + - arm,arm1136j-s + - arm,arm1136jf-s + - arm,arm1156t2-s + - arm,arm1156t2f-s + - arm,arm1176jzf + - arm,arm1176jz-s + - arm,arm1176jzf-s + - arm,arm11mpcore + - arm,armv8 # Only for s/w models + - arm,cortex-a5 + - arm,cortex-a7 + - arm,cortex-a8 + - arm,cortex-a9 + - arm,cortex-a12 + - arm,cortex-a15 + - arm,cortex-a17 + - arm,cortex-a53 + - arm,cortex-a55 + - arm,cortex-a57 + - arm,cortex-a72 + - arm,cortex-a73 + - arm,cortex-m0 + - arm,cortex-m0+ + - arm,cortex-m1 + - arm,cortex-m3 + - arm,cortex-m4 + - arm,cortex-r4 + - arm,cortex-r5 + - arm,cortex-r7 + - brcm,brahma-b15 + - brcm,brahma-b53 + - brcm,vulcan + - cavium,thunder + - cavium,thunder2 + - faraday,fa526 + - intel,sa110 + - intel,sa1100 + - marvell,feroceon + - marvell,mohawk + - marvell,pj4a + - marvell,pj4b + - marvell,sheeva-v5 + - marvell,sheeva-v7 + - nvidia,tegra132-denver + - nvidia,tegra186-denver + - nvidia,tegra194-carmel + - qcom,krait + - qcom,kryo + - qcom,kryo385 + - qcom,kryo485 + - qcom,scorpion + + enable-method: + allOf: + - $ref: '/schemas/types.yaml#/definitions/string' + - oneOf: + # On ARM v8 64-bit this property is required + - enum: + - psci + - spin-table + # On ARM 32-bit systems this property is optional + - enum: + - actions,s500-smp + - allwinner,sun6i-a31 + - allwinner,sun8i-a23 + - allwinner,sun9i-a80-smp + - allwinner,sun8i-a83t-smp + - amlogic,meson8-smp + - amlogic,meson8b-smp + - arm,realview-smp + - aspeed,ast2600-smp + - brcm,bcm11351-cpu-method + - brcm,bcm23550 + - brcm,bcm2836-smp + - brcm,bcm63138 + - brcm,bcm-nsp-smp + - brcm,brahma-b15 + - marvell,armada-375-smp + - marvell,armada-380-smp + - marvell,armada-390-smp + - marvell,armada-xp-smp + - marvell,98dx3236-smp + - mediatek,mt6589-smp + - mediatek,mt81xx-tz-smp + - qcom,gcc-msm8660 + - qcom,kpss-acc-v1 + - qcom,kpss-acc-v2 + - renesas,apmu + - renesas,r9a06g032-smp + - rockchip,rk3036-smp + - rockchip,rk3066-smp + - socionext,milbeaut-m10v-smp + - ste,dbx500-smp + + cpu-release-addr: + $ref: '/schemas/types.yaml#/definitions/uint64' + + description: + Required for systems that have an "enable-method" + property value of "spin-table". + On ARM v8 64-bit systems must be a two cell + property identifying a 64-bit zero-initialised + memory location. + + cpu-idle-states: + $ref: '/schemas/types.yaml#/definitions/phandle-array' + description: | + List of phandles to idle state nodes supported + by this cpu (see ./idle-states.txt). + + capacity-dmips-mhz: + $ref: '/schemas/types.yaml#/definitions/uint32' + description: + u32 value representing CPU capacity (see ./cpu-capacity.txt) in + DMIPS/MHz, relative to highest capacity-dmips-mhz + in the system. + + dynamic-power-coefficient: + $ref: '/schemas/types.yaml#/definitions/uint32' + description: + A u32 value that represents the running time dynamic + power coefficient in units of uW/MHz/V^2. The + coefficient can either be calculated from power + measurements or derived by analysis. + + The dynamic power consumption of the CPU is + proportional to the square of the Voltage (V) and + the clock frequency (f). The coefficient is used to + calculate the dynamic power as below - + + Pdyn = dynamic-power-coefficient * V^2 * f + + where voltage is in V, frequency is in MHz. + + qcom,saw: + $ref: '/schemas/types.yaml#/definitions/phandle' + description: | + Specifies the SAW* node associated with this CPU. - * If cpus node's #address-cells property is set to 2 + Required for systems that have an "enable-method" property + value of "qcom,kpss-acc-v1" or "qcom,kpss-acc-v2" - The first reg cell bits [7:0] must be set to - bits [39:32] of MPIDR_EL1. + * arm/msm/qcom,saw2.txt - The second reg cell bits [23:0] must be set to - bits [23:0] of MPIDR_EL1. + qcom,acc: + $ref: '/schemas/types.yaml#/definitions/phandle' + description: | + Specifies the ACC* node associated with this CPU. - * If cpus node's #address-cells property is set to 1 + Required for systems that have an "enable-method" property + value of "qcom,kpss-acc-v1" or "qcom,kpss-acc-v2" - The reg cell bits [23:0] must be set to bits [23:0] - of MPIDR_EL1. + * arm/msm/qcom,kpss-acc.txt - All other bits in the reg cells must be set to 0. + rockchip,pmu: + $ref: '/schemas/types.yaml#/definitions/phandle' + description: | + Specifies the syscon node controlling the cpu core power domains. - compatible: - items: - - enum: - - arm,arm710t - - arm,arm720t - - arm,arm740t - - arm,arm7ej-s - - arm,arm7tdmi - - arm,arm7tdmi-s - - arm,arm9es - - arm,arm9ej-s - - arm,arm920t - - arm,arm922t - - arm,arm925 - - arm,arm926e-s - - arm,arm926ej-s - - arm,arm940t - - arm,arm946e-s - - arm,arm966e-s - - arm,arm968e-s - - arm,arm9tdmi - - arm,arm1020e - - arm,arm1020t - - arm,arm1022e - - arm,arm1026ej-s - - arm,arm1136j-s - - arm,arm1136jf-s - - arm,arm1156t2-s - - arm,arm1156t2f-s - - arm,arm1176jzf - - arm,arm1176jz-s - - arm,arm1176jzf-s - - arm,arm11mpcore - - arm,armv8 # Only for s/w models - - arm,cortex-a5 - - arm,cortex-a7 - - arm,cortex-a8 - - arm,cortex-a9 - - arm,cortex-a12 - - arm,cortex-a15 - - arm,cortex-a17 - - arm,cortex-a53 - - arm,cortex-a57 - - arm,cortex-a72 - - arm,cortex-a73 - - arm,cortex-m0 - - arm,cortex-m0+ - - arm,cortex-m1 - - arm,cortex-m3 - - arm,cortex-m4 - - arm,cortex-r4 - - arm,cortex-r5 - - arm,cortex-r7 - - brcm,brahma-b15 - - brcm,brahma-b53 - - brcm,vulcan - - cavium,thunder - - cavium,thunder2 - - faraday,fa526 - - intel,sa110 - - intel,sa1100 - - marvell,feroceon - - marvell,mohawk - - marvell,pj4a - - marvell,pj4b - - marvell,sheeva-v5 - - marvell,sheeva-v7 - - nvidia,tegra132-denver - - nvidia,tegra186-denver - - nvidia,tegra194-carmel - - qcom,krait - - qcom,kryo - - qcom,kryo385 - - qcom,scorpion - - enable-method: - allOf: - - $ref: '/schemas/types.yaml#/definitions/string' - - oneOf: - # On ARM v8 64-bit this property is required - - enum: - - psci - - spin-table - # On ARM 32-bit systems this property is optional - - enum: - - actions,s500-smp - - allwinner,sun6i-a31 - - allwinner,sun8i-a23 - - allwinner,sun9i-a80-smp - - allwinner,sun8i-a83t-smp - - amlogic,meson8-smp - - amlogic,meson8b-smp - - arm,realview-smp - - brcm,bcm11351-cpu-method - - brcm,bcm23550 - - brcm,bcm2836-smp - - brcm,bcm63138 - - brcm,bcm-nsp-smp - - brcm,brahma-b15 - - marvell,armada-375-smp - - marvell,armada-380-smp - - marvell,armada-390-smp - - marvell,armada-xp-smp - - marvell,98dx3236-smp - - mediatek,mt6589-smp - - mediatek,mt81xx-tz-smp - - qcom,gcc-msm8660 - - qcom,kpss-acc-v1 - - qcom,kpss-acc-v2 - - renesas,apmu - - renesas,r9a06g032-smp - - rockchip,rk3036-smp - - rockchip,rk3066-smp - - socionext,milbeaut-m10v-smp - - ste,dbx500-smp - - cpu-release-addr: - $ref: '/schemas/types.yaml#/definitions/uint64' - - description: - Required for systems that have an "enable-method" - property value of "spin-table". - On ARM v8 64-bit systems must be a two cell - property identifying a 64-bit zero-initialised - memory location. - - cpu-idle-states: - $ref: '/schemas/types.yaml#/definitions/phandle-array' - description: | - List of phandles to idle state nodes supported - by this cpu (see ./idle-states.txt). - - capacity-dmips-mhz: - $ref: '/schemas/types.yaml#/definitions/uint32' - description: - u32 value representing CPU capacity (see ./cpu-capacity.txt) in - DMIPS/MHz, relative to highest capacity-dmips-mhz - in the system. - - dynamic-power-coefficient: - $ref: '/schemas/types.yaml#/definitions/uint32' - description: - A u32 value that represents the running time dynamic - power coefficient in units of uW/MHz/V^2. The - coefficient can either be calculated from power - measurements or derived by analysis. - - The dynamic power consumption of the CPU is - proportional to the square of the Voltage (V) and - the clock frequency (f). The coefficient is used to - calculate the dynamic power as below - - - Pdyn = dynamic-power-coefficient * V^2 * f - - where voltage is in V, frequency is in MHz. - - qcom,saw: - $ref: '/schemas/types.yaml#/definitions/phandle' - description: | - Specifies the SAW* node associated with this CPU. - - Required for systems that have an "enable-method" property - value of "qcom,kpss-acc-v1" or "qcom,kpss-acc-v2" - - * arm/msm/qcom,saw2.txt - - qcom,acc: - $ref: '/schemas/types.yaml#/definitions/phandle' - description: | - Specifies the ACC* node associated with this CPU. - - Required for systems that have an "enable-method" property - value of "qcom,kpss-acc-v1" or "qcom,kpss-acc-v2" - - * arm/msm/qcom,kpss-acc.txt - - rockchip,pmu: - $ref: '/schemas/types.yaml#/definitions/phandle' - description: | - Specifies the syscon node controlling the cpu core power domains. - - Optional for systems that have an "enable-method" - property value of "rockchip,rk3066-smp" - While optional, it is the preferred way to get access to - the cpu-core power-domains. - - required: - - device_type - - reg - - compatible - - dependencies: - cpu-release-addr: [enable-method] - rockchip,pmu: [enable-method] + Optional for systems that have an "enable-method" + property value of "rockchip,rk3066-smp" + While optional, it is the preferred way to get access to + the cpu-core power-domains. required: - - '#address-cells' - - '#size-cells' + - device_type + - reg + - compatible + +dependencies: + rockchip,pmu: [enable-method] examples: - | diff --git a/Documentation/devicetree/bindings/arm/digicolor.txt b/Documentation/devicetree/bindings/arm/digicolor.txt deleted file mode 100644 index 658553f40b23..000000000000 --- a/Documentation/devicetree/bindings/arm/digicolor.txt +++ /dev/null @@ -1,6 +0,0 @@ -Conexant Digicolor Platforms Device Tree Bindings - -Each device tree must specify which Conexant Digicolor SoC it uses. -Must be the following compatible string: - - cnxt,cx92755 diff --git a/Documentation/devicetree/bindings/arm/digicolor.yaml b/Documentation/devicetree/bindings/arm/digicolor.yaml new file mode 100644 index 000000000000..d9c80b827e9b --- /dev/null +++ b/Documentation/devicetree/bindings/arm/digicolor.yaml @@ -0,0 +1,16 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/digicolor.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Conexant Digicolor Platforms Device Tree Bindings + +maintainers: + - Baruch Siach <baruch@tkos.co.il> + +properties: + compatible: + const: cnxt,cx92755 + +... diff --git a/Documentation/devicetree/bindings/arm/emtrion.txt b/Documentation/devicetree/bindings/arm/emtrion.txt deleted file mode 100644 index 83329aefc483..000000000000 --- a/Documentation/devicetree/bindings/arm/emtrion.txt +++ /dev/null @@ -1,12 +0,0 @@ -Emtrion Devicetree Bindings -=========================== - -emCON Series: -------------- - -Required root node properties - - compatible: - - "emtrion,emcon-mx6", "fsl,imx6q"; : emCON-MX6D or emCON-MX6Q SoM - - "emtrion,emcon-mx6-avari", "fsl,imx6q"; : emCON-MX6D or emCON-MX6Q SoM on Avari Base - - "emtrion,emcon-mx6", "fsl,imx6dl"; : emCON-MX6S or emCON-MX6DL SoM - - "emtrion,emcon-mx6-avari", "fsl,imx6dl"; : emCON-MX6S or emCON-MX6DL SoM on Avari Base diff --git a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt index 5d7dbabbb784..c149fadc6f47 100644 --- a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt +++ b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt @@ -133,6 +133,30 @@ RTC bindings based on SCU Message Protocol Required properties: - compatible: should be "fsl,imx8qxp-sc-rtc"; +OCOTP bindings based on SCU Message Protocol +------------------------------------------------------------ +Required properties: +- compatible: Should be one of: + "fsl,imx8qm-scu-ocotp", + "fsl,imx8qxp-scu-ocotp". +- #address-cells: Must be 1. Contains byte index +- #size-cells: Must be 1. Contains byte length + +Optional Child nodes: + +- Data cells of ocotp: + Detailed bindings are described in bindings/nvmem/nvmem.txt + +Watchdog bindings based on SCU Message Protocol +------------------------------------------------------------ + +Required properties: +- compatible: should be: + "fsl,imx8qxp-sc-wdt" + followed by "fsl,imx-sc-wdt"; +Optional properties: +- timeout-sec: contains the watchdog timeout in seconds. + Example (imx8qxp): ------------- aliases { @@ -177,6 +201,16 @@ firmware { ... }; + ocotp: imx8qx-ocotp { + compatible = "fsl,imx8qxp-scu-ocotp"; + #address-cells = <1>; + #size-cells = <1>; + + fec_mac0: mac@2c4 { + reg = <0x2c4 8>; + }; + }; + pd: imx8qx-pd { compatible = "fsl,imx8qxp-scu-pd", "fsl,scu-pd"; #power-domain-cells = <1>; @@ -185,6 +219,11 @@ firmware { rtc: rtc { compatible = "fsl,imx8qxp-sc-rtc"; }; + + watchdog { + compatible = "fsl,imx8qxp-sc-wdt", "fsl,imx-sc-wdt"; + timeout-sec = <60>; + }; }; }; diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index 407138ebc0d0..1b4b4e6573b5 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -15,6 +15,13 @@ properties: const: '/' compatible: oneOf: + - description: i.MX1 based Boards + items: + - enum: + - armadeus,imx1-apf9328 + - fsl,imx1ads + - const: fsl,imx1 + - description: i.MX23 based Boards items: - enum: @@ -51,6 +58,25 @@ properties: - const: i2se,duckbill-2 - const: fsl,imx28 + - description: i.MX31 based Boards + items: + - enum: + - buglabs,imx31-bug + - logicpd,imx31-lite + - const: fsl,imx31 + + - description: i.MX35 based Boards + items: + - enum: + - fsl,imx35-pdk + - const: fsl,imx35 + + - description: i.MX35 Eukrea CPUIMX35 Board + items: + - const: eukrea,mbimxsd35-baseboard + - const: eukrea,cpuimx35 + - const: fsl,imx35 + - description: i.MX50 based Boards items: - enum: @@ -80,6 +106,8 @@ properties: - description: i.MX6Q based Boards items: - enum: + - emtrion,emcon-mx6 # emCON-MX6D or emCON-MX6Q SoM + - emtrion,emcon-mx6-avari # emCON-MX6D or emCON-MX6Q SoM on Avari Base - fsl,imx6q-arm2 - fsl,imx6q-sabreauto - fsl,imx6q-sabrelite @@ -99,6 +127,8 @@ properties: items: - enum: - eckelmann,imx6dl-ci4x10 + - emtrion,emcon-mx6 # emCON-MX6S or emCON-MX6DL SoM + - emtrion,emcon-mx6-avari # emCON-MX6S or emCON-MX6DL SoM on Avari Base - fsl,imx6dl-sabreauto # i.MX6 DualLite/Solo SABRE Automotive Board - fsl,imx6dl-sabresd # i.MX6 DualLite SABRE Smart Device Board - technologic,imx6dl-ts4900 @@ -131,6 +161,20 @@ properties: items: - enum: - fsl,imx6ul-14x14-evk # i.MX6 UltraLite 14x14 EVK Board + - kontron,imx6ul-n6310-som # Kontron N6310 SOM + - const: fsl,imx6ul + + - description: Kontron N6310 S Board + items: + - const: kontron,imx6ul-n6310-s + - const: kontron,imx6ul-n6310-som + - const: fsl,imx6ul + + - description: Kontron N6310 S 43 Board + items: + - const: kontron,imx6ul-n6310-s-43 + - const: kontron,imx6ul-n6310-s + - const: kontron,imx6ul-n6310-som - const: fsl,imx6ul - description: i.MX6ULL based Boards @@ -156,7 +200,9 @@ properties: items: - enum: - fsl,imx7d-sdb # i.MX7 SabreSD Board + - novtech,imx7d-meerkat96 # i.MX7 Meerkat96 Board - tq,imx7d-mba7 # i.MX7D TQ MBa7 with TQMa7D SoM + - zii,imx7d-rmu2 # ZII RMU2 Board - zii,imx7d-rpu2 # ZII RPU2 Board - const: fsl,imx7d @@ -171,15 +217,38 @@ properties: - const: compulab,cl-som-imx7 - const: fsl,imx7d + - description: i.MX7ULP based Boards + items: + - enum: + - fsl,imx7ulp-evk # i.MX7ULP Evaluation Kit + - const: fsl,imx7ulp + - description: i.MX8MM based Boards items: - enum: - fsl,imx8mm-evk # i.MX8MM EVK Board - const: fsl,imx8mm + - description: i.MX8MN based Boards + items: + - enum: + - fsl,imx8mn-ddr4-evk # i.MX8MN DDR4 EVK Board + - const: fsl,imx8mn + + - description: i.MX8MQ based Boards + items: + - enum: + - boundary,imx8mq-nitrogen8m # i.MX8MQ NITROGEN Board + - fsl,imx8mq-evk # i.MX8MQ EVK Board + - purism,librem5-devkit # Purism Librem5 devkit + - solidrun,hummingboard-pulse # SolidRun Hummingboard Pulse + - technexion,pico-pi-imx8m # TechNexion PICO-PI-8M evk + - const: fsl,imx8mq + - description: i.MX8QXP based Boards items: - enum: + - einfochips,imx8qxp-ai_ml # i.MX8QXP AI_ML Board - fsl,imx8qxp-mek # i.MX8QXP MEK Board - const: fsl,imx8qxp @@ -239,6 +308,7 @@ properties: - description: LS1046A based Boards items: - enum: + - fsl,ls1046a-frwy - fsl,ls1046a-qds - fsl,ls1046a-rdb - const: fsl,ls1046a diff --git a/Documentation/devicetree/bindings/arm/idle-states.txt b/Documentation/devicetree/bindings/arm/idle-states.txt index 45730ba60af5..771f5d20ae18 100644 --- a/Documentation/devicetree/bindings/arm/idle-states.txt +++ b/Documentation/devicetree/bindings/arm/idle-states.txt @@ -28,7 +28,7 @@ PM implementation to put the processor in different idle states (which include states listed above; "off" state is not an idle state since it does not have wake-up capabilities, hence it is not considered in this document). -Idle state parameters (eg entry latency) are platform specific and need to be +Idle state parameters (e.g. entry latency) are platform specific and need to be characterized with bindings that provide the required information to OS PM code so that it can build the required tables and use them at runtime. @@ -90,24 +90,24 @@ These timing parameters can be used by an OS in different circumstances. An idle CPU requires the expected min-residency time to select the most appropriate idle state based on the expected expiry time of the next IRQ -(ie wake-up) that causes the CPU to return to the EXEC phase. +(i.e. wake-up) that causes the CPU to return to the EXEC phase. An operating system scheduler may need to compute the shortest wake-up delay for CPUs in the system by detecting how long will it take to get a CPU out -of an idle state, eg: +of an idle state, e.g.: wakeup-delay = exit-latency + max(entry-latency - (now - entry-timestamp), 0) In other words, the scheduler can make its scheduling decision by selecting -(eg waking-up) the CPU with the shortest wake-up latency. -The wake-up latency must take into account the entry latency if that period +(e.g. waking-up) the CPU with the shortest wake-up delay. +The wake-up delay must take into account the entry latency if that period has not expired. The abortable nature of the PREP period can be ignored if it cannot be relied upon (e.g. the PREP deadline may occur much sooner than -the worst case since it depends on the CPU operating conditions, ie caches +the worst case since it depends on the CPU operating conditions, i.e. caches state). An OS has to reliably probe the wakeup-latency since some devices can enforce -latency constraints guarantees to work properly, so the OS has to detect the +latency constraint guarantees to work properly, so the OS has to detect the worst case wake-up latency it can incur if a CPU is allowed to enter an idle state, and possibly to prevent that to guarantee reliable device functioning. @@ -183,15 +183,15 @@ and IDLE2: Graph 2: idle states min-residency example In graph 2 above, that takes into account idle states entry/exit energy -costs, it is clear that if the idle state residency time (ie time till next +costs, it is clear that if the idle state residency time (i.e. time till next wake-up IRQ) is less than IDLE2-min-residency, IDLE1 is the better idle state choice energywise. This is mainly down to the fact that IDLE1 entry/exit energy costs are lower than IDLE2. -However, the lower power consumption (ie shallower energy curve slope) of idle -state IDLE2 implies that after a suitable time, IDLE2 becomes more energy +However, the lower power consumption (i.e. shallower energy curve slope) of +idle state IDLE2 implies that after a suitable time, IDLE2 becomes more energy efficient. The time at which IDLE2 becomes more energy efficient than IDLE1 (and other @@ -214,8 +214,8 @@ processor idle states, defined as device tree nodes, are listed. Usage: Optional - On ARM systems, it is a container of processor idle states nodes. If the system does not provide CPU - power management capabilities or the processor just - supports idle_standby an idle-states node is not + power management capabilities, or the processor just + supports idle_standby, an idle-states node is not required. Description: idle-states node is a container node, where its @@ -241,9 +241,13 @@ processor idle states, defined as device tree nodes, are listed. - "psci" # On ARM 32-bit systems this property is optional -The nodes describing the idle states (state) can only be defined within the -idle-states node, any other configuration is considered invalid and therefore -must be ignored. +This assumes that the "enable-method" property is set to "psci" in the cpu +node[6] that is responsible for setting up CPU idle management in the OS +implementation. + +The nodes describing the idle states (state) can only be defined +within the idle-states node, any other configuration is considered invalid +and therefore must be ignored. =========================================== 4 - state node @@ -283,14 +287,14 @@ follows: Value type: <prop-encoded-array> Definition: u32 value representing worst case latency in microseconds required to enter the idle state. - The exit-latency-us duration may be guaranteed - only after entry-latency-us has passed. - exit-latency-us Usage: Required Value type: <prop-encoded-array> Definition: u32 value representing worst case latency in microseconds required to exit the idle state. + The exit-latency-us duration may be guaranteed + only after entry-latency-us has passed. - min-residency-us Usage: Required @@ -338,8 +342,8 @@ follows: state. In addition to the properties listed above, a state node may require - additional properties specifics to the entry-method defined in the - idle-states node, please refer to the entry-method bindings + additional properties specific to the entry-method defined in the + idle-states node. Please refer to the entry-method bindings documentation for properties definitions. =========================================== @@ -687,7 +691,7 @@ cpus { Documentation/devicetree/bindings/arm/cpus.yaml [2] ARM Linux Kernel documentation - PSCI bindings - Documentation/devicetree/bindings/arm/psci.txt + Documentation/devicetree/bindings/arm/psci.yaml [3] ARM Server Base System Architecture (SBSA) http://infocenter.arm.com/help/index.jsp @@ -697,3 +701,6 @@ cpus { [5] Devicetree Specification https://www.devicetree.org/specifications/ + +[6] ARM Linux Kernel documentation - Booting AArch64 Linux + Documentation/arm64/booting.rst diff --git a/Documentation/devicetree/bindings/arm/l2c2x0.yaml b/Documentation/devicetree/bindings/arm/l2c2x0.yaml index bfc5c185561c..913a8cd8b2c0 100644 --- a/Documentation/devicetree/bindings/arm/l2c2x0.yaml +++ b/Documentation/devicetree/bindings/arm/l2c2x0.yaml @@ -176,6 +176,10 @@ properties: description: disable parity checking on the L2 cache (L220 or PL310). type: boolean + marvell,ecc-enable: + description: enable ECC protection on the L2 cache + type: boolean + arm,outer-sync-disable: description: disable the outer sync operation on the L2 cache. Some core tiles, especially ARM PB11MPCore have a faulty L220 cache that diff --git a/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt b/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt index 7b8b8eb0191f..26410fbb85be 100644 --- a/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt +++ b/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt @@ -18,17 +18,19 @@ Clocks: ------- -The Device Tree node representing the AP806 system controller provides -a number of clocks: +The Device Tree node representing the AP806/AP807 system controller +provides a number of clocks: - - 0: clock of CPU cluster 0 - - 1: clock of CPU cluster 1 + - 0: reference clock of CPU cluster 0 + - 1: reference clock of CPU cluster 1 - 2: fixed PLL at 1200 Mhz - 3: MSS clock, derived from the fixed PLL Required properties: - - compatible: must be: "marvell,ap806-clock" + - compatible: must be one of: + * "marvell,ap806-clock" + * "marvell,ap807-clock" - #clock-cells: must be set to 1 Pinctrl: @@ -143,3 +145,33 @@ ap_syscon1: system-controller@6f8000 { #thermal-sensor-cells = <1>; }; }; + +Cluster clocks: +--------------- + +Device Tree Clock bindings for cluster clock of Marvell +AP806/AP807. Each cluster contain up to 2 CPUs running at the same +frequency. + +Required properties: + - compatible: must be one of: + * "marvell,ap806-cpu-clock" + * "marvell,ap807-cpu-clock" +- #clock-cells : should be set to 1. + +- clocks : shall be the input parent clock(s) phandle for the clock + (one per cluster) + +- reg: register range associated with the cluster clocks + +ap_syscon1: system-controller@6f8000 { + compatible = "marvell,armada-ap806-syscon1", "syscon", "simple-mfd"; + reg = <0x6f8000 0x1000>; + + cpu_clk: clock-cpu@278 { + compatible = "marvell,ap806-cpu-clock"; + clocks = <&ap_clk 0>, <&ap_clk 1>; + #clock-cells = <1>; + reg = <0x278 0xa30>; + }; +}; diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-37xx.txt b/Documentation/devicetree/bindings/arm/marvell/armada-37xx.txt index eddde4faef01..f6d6642d81c0 100644 --- a/Documentation/devicetree/bindings/arm/marvell/armada-37xx.txt +++ b/Documentation/devicetree/bindings/arm/marvell/armada-37xx.txt @@ -48,3 +48,11 @@ avs: avs@11500 { compatible = "marvell,armada-3700-avs", "syscon"; reg = <0x11500 0x40>; } + + +CZ.NIC's Turris Mox SOHO router Device Tree Bindings +---------------------------------------------------- + +Required root node property: + + - compatible: must contain "cznic,turris-mox" diff --git a/Documentation/devicetree/bindings/arm/marvell/cp110-system-controller.txt b/Documentation/devicetree/bindings/arm/marvell/cp110-system-controller.txt index 4db4119a6d19..f982a8ed9396 100644 --- a/Documentation/devicetree/bindings/arm/marvell/cp110-system-controller.txt +++ b/Documentation/devicetree/bindings/arm/marvell/cp110-system-controller.txt @@ -78,8 +78,8 @@ Documentation/devicetree/bindings/pinctrl/marvell,mvebu-pinctrl.txt. Required properties: -- compatible: "marvell,armada-7k-pinctrl", - "marvell,armada-8k-cpm-pinctrl" or "marvell,armada-8k-cps-pinctrl" +- compatible: "marvell,armada-7k-pinctrl", "marvell,armada-8k-cpm-pinctrl", + "marvell,armada-8k-cps-pinctrl" or "marvell,cp115-standalone-pinctrl" depending on the specific variant of the SoC being used. Available mpp pins/groups and functions: diff --git a/Documentation/devicetree/bindings/arm/mediatek.txt b/Documentation/devicetree/bindings/arm/mediatek.txt deleted file mode 100644 index 56ac7896d6d8..000000000000 --- a/Documentation/devicetree/bindings/arm/mediatek.txt +++ /dev/null @@ -1,89 +0,0 @@ -MediaTek SoC based Platforms Device Tree Bindings - -Boards with a MediaTek SoC shall have the following property: - -Required root node property: - -compatible: Must contain one of - "mediatek,mt2701" - "mediatek,mt2712" - "mediatek,mt6580" - "mediatek,mt6589" - "mediatek,mt6592" - "mediatek,mt6755" - "mediatek,mt6765" - "mediatek,mt6795" - "mediatek,mt6797" - "mediatek,mt7622" - "mediatek,mt7623" - "mediatek,mt7629" - "mediatek,mt8127" - "mediatek,mt8135" - "mediatek,mt8173" - "mediatek,mt8183" - - -Supported boards: - -- Evaluation board for MT2701: - Required root node properties: - - compatible = "mediatek,mt2701-evb", "mediatek,mt2701"; -- Evaluation board for MT2712: - Required root node properties: - - compatible = "mediatek,mt2712-evb", "mediatek,mt2712"; -- Evaluation board for MT6580: - Required root node properties: - - compatible = "mediatek,mt6580-evbp1", "mediatek,mt6580"; -- bq Aquaris5 smart phone: - Required root node properties: - - compatible = "mundoreader,bq-aquaris5", "mediatek,mt6589"; -- Evaluation board for MT6592: - Required root node properties: - - compatible = "mediatek,mt6592-evb", "mediatek,mt6592"; -- Evaluation phone for MT6755(Helio P10): - Required root node properties: - - compatible = "mediatek,mt6755-evb", "mediatek,mt6755"; -- Evaluation board for MT6765(Helio P22): - Required root node properties: - - compatible = "mediatek,mt6765-evb", "mediatek,mt6765"; -- Evaluation board for MT6795(Helio X10): - Required root node properties: - - compatible = "mediatek,mt6795-evb", "mediatek,mt6795"; -- Evaluation board for MT6797(Helio X20): - Required root node properties: - - compatible = "mediatek,mt6797-evb", "mediatek,mt6797"; -- Mediatek X20 Development Board: - Required root node properties: - - compatible = "archermind,mt6797-x20-dev", "mediatek,mt6797"; -- Reference board variant 1 for MT7622: - Required root node properties: - - compatible = "mediatek,mt7622-rfb1", "mediatek,mt7622"; -- Bananapi BPI-R64 for MT7622: - Required root node properties: - - compatible = "bananapi,bpi-r64", "mediatek,mt7622"; -- Reference board for MT7623a with eMMC: - Required root node properties: - - compatible = "mediatek,mt7623a-rfb-emmc", "mediatek,mt7623"; -- Reference board for MT7623a with NAND: - Required root node properties: - - compatible = "mediatek,mt7623a-rfb-nand", "mediatek,mt7623"; -- Reference board for MT7623n with eMMC: - Required root node properties: - - compatible = "mediatek,mt7623n-rfb-emmc", "mediatek,mt7623"; -- Bananapi BPI-R2 board: - - compatible = "bananapi,bpi-r2", "mediatek,mt7623"; -- Reference board for MT7629: - Required root node properties: - - compatible = "mediatek,mt7629-rfb", "mediatek,mt7629"; -- MTK mt8127 tablet moose EVB: - Required root node properties: - - compatible = "mediatek,mt8127-moose", "mediatek,mt8127"; -- MTK mt8135 tablet EVB: - Required root node properties: - - compatible = "mediatek,mt8135-evbp1", "mediatek,mt8135"; -- MTK mt8173 tablet EVB: - Required root node properties: - - compatible = "mediatek,mt8173-evb", "mediatek,mt8173"; -- Evaluation board for MT8183: - Required root node properties: - - compatible = "mediatek,mt8183-evb", "mediatek,mt8183"; diff --git a/Documentation/devicetree/bindings/arm/mediatek.yaml b/Documentation/devicetree/bindings/arm/mediatek.yaml new file mode 100644 index 000000000000..4043c5046441 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mediatek.yaml @@ -0,0 +1,95 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/mediatek.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek SoC based Platforms Device Tree Bindings + +maintainers: + - Sean Wang <sean.wang@mediatek.com> + - Matthias Brugger <matthias.bgg@gmail.com> +description: | + Boards with a MediaTek SoC shall have the following properties. + +properties: + $nodename: + const: '/' + compatible: + oneOf: + - items: + - enum: + - mediatek,mt2701-evb + - const: mediatek,mt2701 + + - items: + - enum: + - mediatek,mt2712-evb + - const: mediatek,mt2712 + - items: + - enum: + - mediatek,mt6580-evbp1 + - const: mediatek,mt6580 + - items: + - enum: + - mundoreader,bq-aquaris5 + - const: mediatek,mt6589 + - items: + - enum: + - mediatek,mt6592-evb + - const: mediatek,mt6592 + - items: + - enum: + - mediatek,mt6755-evb + - const: mediatek,mt6755 + - items: + - enum: + - mediatek,mt6765-evb + - const: mediatek,mt6765 + - items: + - enum: + - mediatek,mt6779-evb + - const: mediatek,mt6779 + - items: + - enum: + - mediatek,mt6795-evb + - const: mediatek,mt6795 + - items: + - enum: + - archermind,mt6797-x20-dev + - mediatek,mt6797-evb + - const: mediatek,mt6797 + - items: + - enum: + - bananapi,bpi-r64 + - mediatek,mt7622-rfb1 + - const: mediatek,mt7622 + - items: + - enum: + - mediatek,mt7623a-rfb-emmc + - mediatek,mt7623a-rfb-nand + - mediatek,mt7623n-rfb-emmc + - bananapi,bpi-r2 + - const: mediatek,mt7623 + + - items: + - enum: + - mediatek,mt7629-rfb + - const: mediatek,mt7629 + - items: + - enum: + - mediatek,mt8127-moose + - const: mediatek,mt8127 + - items: + - enum: + - mediatek,mt8135-evbp1 + - const: mediatek,mt8135 + - items: + - enum: + - mediatek,mt8173-evb + - const: mediatek,mt8173 + - items: + - enum: + - mediatek,mt8183-evb + - const: mediatek,mt8183 +... diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt index 161e63a6c254..ff000ccade78 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt @@ -8,6 +8,7 @@ Required Properties: - compatible: Should be one of: - "mediatek,mt2701-apmixedsys" - "mediatek,mt2712-apmixedsys", "syscon" + - "mediatek,mt6779-apmixedsys", "syscon" - "mediatek,mt6797-apmixedsys" - "mediatek,mt7622-apmixedsys" - "mediatek,mt7623-apmixedsys", "mediatek,mt2701-apmixedsys" diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt index f3cef1a6d95c..e4ca7b703123 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt @@ -7,9 +7,11 @@ Required Properties: - compatible: Should be one of: - "mediatek,mt2701-audsys", "syscon" + - "mediatek,mt6779-audio", "syscon" - "mediatek,mt7622-audsys", "syscon" - "mediatek,mt7623-audsys", "mediatek,mt2701-audsys", "syscon" - "mediatek,mt8183-audiosys", "syscon" + - "mediatek,mt8516-audsys", "syscon" - #clock-cells: Must be 1 The AUDSYS controller uses the common clk binding from diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,camsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,camsys.txt index d8930f64aa98..1f4aaa15a37e 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,camsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,camsys.txt @@ -6,6 +6,7 @@ The MediaTek camsys controller provides various clocks to the system. Required Properties: - compatible: Should be one of: + - "mediatek,mt6779-camsys", "syscon" - "mediatek,mt8183-camsys", "syscon" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt index e3bc4a1e7a6e..2b693e343c56 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt @@ -8,6 +8,7 @@ Required Properties: - compatible: Should be one of: - "mediatek,mt2701-imgsys", "syscon" - "mediatek,mt2712-imgsys", "syscon" + - "mediatek,mt6779-imgsys", "syscon" - "mediatek,mt6797-imgsys", "syscon" - "mediatek,mt7623-imgsys", "mediatek,mt2701-imgsys", "syscon" - "mediatek,mt8173-imgsys", "syscon" diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt index a90913988d7e..db2f4fd754e7 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt @@ -9,6 +9,7 @@ Required Properties: - compatible: Should be one of: - "mediatek,mt2701-infracfg", "syscon" - "mediatek,mt2712-infracfg", "syscon" + - "mediatek,mt6779-infracfg_ao", "syscon" - "mediatek,mt6797-infracfg", "syscon" - "mediatek,mt7622-infracfg", "syscon" - "mediatek,mt7623-infracfg", "mediatek,mt2701-infracfg", "syscon" diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,ipesys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ipesys.txt new file mode 100644 index 000000000000..2ce889b023d9 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ipesys.txt @@ -0,0 +1,22 @@ +Mediatek ipesys controller +============================ + +The Mediatek ipesys controller provides various clocks to the system. + +Required Properties: + +- compatible: Should be one of: + - "mediatek,mt6779-ipesys", "syscon" +- #clock-cells: Must be 1 + +The ipesys controller uses the common clk binding from +Documentation/devicetree/bindings/clock/clock-bindings.txt +The available clocks are defined in dt-bindings/clock/mt*-clk.h. + +Example: + +ipesys: clock-controller@1b000000 { + compatible = "mediatek,mt6779-ipesys", "syscon"; + reg = <0 0x1b000000 0 0x1000>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mfgcfg.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mfgcfg.txt index 72787e7dd227..ad5f9d2f6818 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mfgcfg.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mfgcfg.txt @@ -7,6 +7,7 @@ Required Properties: - compatible: Should be one of: - "mediatek,mt2712-mfgcfg", "syscon" + - "mediatek,mt6779-mfgcfg", "syscon" - "mediatek,mt8183-mfgcfg", "syscon" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt index 545eab717c96..301eefbe1618 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt @@ -8,6 +8,7 @@ Required Properties: - compatible: Should be one of: - "mediatek,mt2701-mmsys", "syscon" - "mediatek,mt2712-mmsys", "syscon" + - "mediatek,mt6779-mmsys", "syscon" - "mediatek,mt6797-mmsys", "syscon" - "mediatek,mt7623-mmsys", "mediatek,mt2701-mmsys", "syscon" - "mediatek,mt8173-mmsys", "syscon" diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt index 4c7e478117a0..ecf027a9003a 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt @@ -14,6 +14,7 @@ Required Properties: - "mediatek,mt7629-pericfg", "syscon" - "mediatek,mt8135-pericfg", "syscon" - "mediatek,mt8173-pericfg", "syscon" + - "mediatek,mt8183-pericfg", "syscon" - #clock-cells: Must be 1 - #reset-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt index a023b8338960..0293d693ce0c 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt @@ -8,6 +8,7 @@ Required Properties: - compatible: Should be one of: - "mediatek,mt2701-topckgen" - "mediatek,mt2712-topckgen", "syscon" + - "mediatek,mt6779-topckgen", "syscon" - "mediatek,mt6797-topckgen" - "mediatek,mt7622-topckgen" - "mediatek,mt7623-topckgen", "mediatek,mt2701-topckgen" diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt index 57176bb8dbb5..7894558b7a1c 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt @@ -8,6 +8,7 @@ Required Properties: - compatible: Should be one of: - "mediatek,mt2701-vdecsys", "syscon" - "mediatek,mt2712-vdecsys", "syscon" + - "mediatek,mt6779-vdecsys", "syscon" - "mediatek,mt6797-vdecsys", "syscon" - "mediatek,mt7623-vdecsys", "mediatek,mt2701-vdecsys", "syscon" - "mediatek,mt8173-vdecsys", "syscon" diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,vencsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vencsys.txt index c9faa6269087..6a6a14e15cd7 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,vencsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vencsys.txt @@ -7,6 +7,7 @@ Required Properties: - compatible: Should be one of: - "mediatek,mt2712-vencsys", "syscon" + - "mediatek,mt6779-vencsys", "syscon" - "mediatek,mt6797-vencsys", "syscon" - "mediatek,mt8173-vencsys", "syscon" - "mediatek,mt8183-vencsys", "syscon" diff --git a/Documentation/devicetree/bindings/arm/moxart.txt b/Documentation/devicetree/bindings/arm/moxart.txt deleted file mode 100644 index 11087edb0658..000000000000 --- a/Documentation/devicetree/bindings/arm/moxart.txt +++ /dev/null @@ -1,12 +0,0 @@ -MOXA ART device tree bindings - -Boards with the MOXA ART SoC shall have the following properties: - -Required root node property: - -compatible = "moxa,moxart"; - -Boards: - -- UC-7112-LX: embedded computer - compatible = "moxa,moxart-uc-7112-lx", "moxa,moxart" diff --git a/Documentation/devicetree/bindings/arm/moxart.yaml b/Documentation/devicetree/bindings/arm/moxart.yaml new file mode 100644 index 000000000000..c068df59fad2 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/moxart.yaml @@ -0,0 +1,19 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/moxart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MOXA ART device tree bindings + +maintainers: + - Jonas Jensen <jonas.jensen@gmail.com> + +properties: + compatible: + description: UC-7112-LX embedded computer + items: + - const: moxa,moxart-uc-7112-lx + - const: moxa,moxart + +... diff --git a/Documentation/devicetree/bindings/arm/nxp/lpc32xx.txt b/Documentation/devicetree/bindings/arm/nxp/lpc32xx.txt deleted file mode 100644 index 56ec8ddc4a3b..000000000000 --- a/Documentation/devicetree/bindings/arm/nxp/lpc32xx.txt +++ /dev/null @@ -1,8 +0,0 @@ -NXP LPC32xx Platforms Device Tree Bindings ------------------------------------------- - -Boards with the NXP LPC32xx SoC shall have the following properties: - -Required root node property: - -compatible: must be "nxp,lpc3220", "nxp,lpc3230", "nxp,lpc3240" or "nxp,lpc3250" diff --git a/Documentation/devicetree/bindings/arm/nxp/lpc32xx.yaml b/Documentation/devicetree/bindings/arm/nxp/lpc32xx.yaml new file mode 100644 index 000000000000..07f39d3eee7e --- /dev/null +++ b/Documentation/devicetree/bindings/arm/nxp/lpc32xx.yaml @@ -0,0 +1,25 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/nxp/lpc32xx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP LPC32xx Platforms Device Tree Bindings + +maintainers: + - Roland Stigge <stigge@antcom.de> + +properties: + compatible: + oneOf: + - enum: + - nxp,lpc3220 + - nxp,lpc3230 + - nxp,lpc3240 + - items: + - enum: + - ea,ea3250 + - phytec,phy3250 + - const: nxp,lpc3250 + +... diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 1c1e48fd94b5..b301f753ed2c 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -160,6 +160,9 @@ Boards: - AM335X phyCORE-AM335x: Development kit compatible = "phytec,am335x-pcm-953", "phytec,am335x-phycore-som", "ti,am33xx" +- AM335x phyBOARD-REGOR: Single Board Computer + compatible = "phytec,am335x-regor", "phytec,am335x-phycore-som", "ti,am33xx" + - AM335X UC-8100-ME-T: Communication-centric industrial computing platform compatible = "moxa,uc-8100-me-t", "ti,am33xx"; diff --git a/Documentation/devicetree/bindings/arm/psci.txt b/Documentation/devicetree/bindings/arm/psci.txt deleted file mode 100644 index a2c4f1d52492..000000000000 --- a/Documentation/devicetree/bindings/arm/psci.txt +++ /dev/null @@ -1,111 +0,0 @@ -* Power State Coordination Interface (PSCI) - -Firmware implementing the PSCI functions described in ARM document number -ARM DEN 0022A ("Power State Coordination Interface System Software on ARM -processors") can be used by Linux to initiate various CPU-centric power -operations. - -Issue A of the specification describes functions for CPU suspend, hotplug -and migration of secure software. - -Functions are invoked by trapping to the privilege level of the PSCI -firmware (specified as part of the binding below) and passing arguments -in a manner similar to that specified by AAPCS: - - r0 => 32-bit Function ID / return value - {r1 - r3} => Parameters - -Note that the immediate field of the trapping instruction must be set -to #0. - - -Main node required properties: - - - compatible : should contain at least one of: - - * "arm,psci" : For implementations complying to PSCI versions prior - to 0.2. - For these cases function IDs must be provided. - - * "arm,psci-0.2" : For implementations complying to PSCI 0.2. - Function IDs are not required and should be ignored by - an OS with PSCI 0.2 support, but are permitted to be - present for compatibility with existing software when - "arm,psci" is later in the compatible list. - - * "arm,psci-1.0" : For implementations complying to PSCI 1.0. - PSCI 1.0 is backward compatible with PSCI 0.2 with - minor specification updates, as defined in the PSCI - specification[2]. - - - method : The method of calling the PSCI firmware. Permitted - values are: - - "smc" : SMC #0, with the register assignments specified - in this binding. - - "hvc" : HVC #0, with the register assignments specified - in this binding. - -Main node optional properties: - - - cpu_suspend : Function ID for CPU_SUSPEND operation - - - cpu_off : Function ID for CPU_OFF operation - - - cpu_on : Function ID for CPU_ON operation - - - migrate : Function ID for MIGRATE operation - -Device tree nodes that require usage of PSCI CPU_SUSPEND function (ie idle -state nodes, as per bindings in [1]) must specify the following properties: - -- arm,psci-suspend-param - Usage: Required for state nodes[1] if the corresponding - idle-states node entry-method property is set - to "psci". - Value type: <u32> - Definition: power_state parameter to pass to the PSCI - suspend call. - -Example: - -Case 1: PSCI v0.1 only. - - psci { - compatible = "arm,psci"; - method = "smc"; - cpu_suspend = <0x95c10000>; - cpu_off = <0x95c10001>; - cpu_on = <0x95c10002>; - migrate = <0x95c10003>; - }; - -Case 2: PSCI v0.2 only - - psci { - compatible = "arm,psci-0.2"; - method = "smc"; - }; - -Case 3: PSCI v0.2 and PSCI v0.1. - - A DTB may provide IDs for use by kernels without PSCI 0.2 support, - enabling firmware and hypervisors to support existing and new kernels. - These IDs will be ignored by kernels with PSCI 0.2 support, which will - use the standard PSCI 0.2 IDs exclusively. - - psci { - compatible = "arm,psci-0.2", "arm,psci"; - method = "hvc"; - - cpu_on = < arbitrary value >; - cpu_off = < arbitrary value >; - - ... - }; - -[1] Kernel documentation - ARM idle states bindings - Documentation/devicetree/bindings/arm/idle-states.txt -[2] Power State Coordination Interface (PSCI) specification - http://infocenter.arm.com/help/topic/com.arm.doc.den0022c/DEN0022C_Power_State_Coordination_Interface.pdf diff --git a/Documentation/devicetree/bindings/arm/psci.yaml b/Documentation/devicetree/bindings/arm/psci.yaml new file mode 100644 index 000000000000..7abdf58b335e --- /dev/null +++ b/Documentation/devicetree/bindings/arm/psci.yaml @@ -0,0 +1,163 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/psci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Power State Coordination Interface (PSCI) + +maintainers: + - Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> + +description: |+ + Firmware implementing the PSCI functions described in ARM document number + ARM DEN 0022A ("Power State Coordination Interface System Software on ARM + processors") can be used by Linux to initiate various CPU-centric power + operations. + + Issue A of the specification describes functions for CPU suspend, hotplug + and migration of secure software. + + Functions are invoked by trapping to the privilege level of the PSCI + firmware (specified as part of the binding below) and passing arguments + in a manner similar to that specified by AAPCS: + + r0 => 32-bit Function ID / return value + {r1 - r3} => Parameters + + Note that the immediate field of the trapping instruction must be set + to #0. + + [2] Power State Coordination Interface (PSCI) specification + http://infocenter.arm.com/help/topic/com.arm.doc.den0022c/DEN0022C_Power_State_Coordination_Interface.pdf + +properties: + compatible: + oneOf: + - description: + For implementations complying to PSCI versions prior to 0.2. + const: arm,psci + + - description: + For implementations complying to PSCI 0.2. + const: arm,psci-0.2 + + - description: + For implementations complying to PSCI 0.2. + Function IDs are not required and should be ignored by an OS with + PSCI 0.2 support, but are permitted to be present for compatibility + with existing software when "arm,psci" is later in the compatible + list. + items: + - const: arm,psci-0.2 + - const: arm,psci + + - description: + For implementations complying to PSCI 1.0. + const: arm,psci-1.0 + + - description: + For implementations complying to PSCI 1.0. + PSCI 1.0 is backward compatible with PSCI 0.2 with minor + specification updates, as defined in the PSCI specification[2]. + items: + - const: arm,psci-1.0 + - const: arm,psci-0.2 + + method: + description: The method of calling the PSCI firmware. + allOf: + - $ref: /schemas/types.yaml#/definitions/string-array + - enum: + # SMC #0, with the register assignments specified in this binding. + - smc + # HVC #0, with the register assignments specified in this binding. + - hvc + + cpu_suspend: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Function ID for CPU_SUSPEND operation + + cpu_off: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Function ID for CPU_OFF operation + + cpu_on: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Function ID for CPU_ON operation + + migrate: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Function ID for MIGRATE operation + + arm,psci-suspend-param: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + power_state parameter to pass to the PSCI suspend call. + + Device tree nodes that require usage of PSCI CPU_SUSPEND function (ie + idle state nodes with entry-method property is set to "psci", as per + bindings in [1]) must specify this property. + + [1] Kernel documentation - ARM idle states bindings + Documentation/devicetree/bindings/arm/idle-states.txt + + +required: + - compatible + - method + +allOf: + - if: + properties: + compatible: + contains: + const: arm,psci + then: + required: + - cpu_off + - cpu_on + +examples: + - |+ + + // Case 1: PSCI v0.1 only. + + psci { + compatible = "arm,psci"; + method = "smc"; + cpu_suspend = <0x95c10000>; + cpu_off = <0x95c10001>; + cpu_on = <0x95c10002>; + migrate = <0x95c10003>; + }; + + - |+ + + // Case 2: PSCI v0.2 only + + psci { + compatible = "arm,psci-0.2"; + method = "smc"; + }; + + + - |+ + + // Case 3: PSCI v0.2 and PSCI v0.1. + + /* + * A DTB may provide IDs for use by kernels without PSCI 0.2 support, + * enabling firmware and hypervisors to support existing and new kernels. + * These IDs will be ignored by kernels with PSCI 0.2 support, which will + * use the standard PSCI 0.2 IDs exclusively. + */ + + psci { + compatible = "arm,psci-0.2", "arm,psci"; + method = "hvc"; + + cpu_on = <0x95c10002>; + cpu_off = <0x95c10001>; + }; +... diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml index f6316ab66385..e39d8f02e33c 100644 --- a/Documentation/devicetree/bindings/arm/qcom.yaml +++ b/Documentation/devicetree/bindings/arm/qcom.yaml @@ -45,6 +45,7 @@ description: | mtp sbc hk01 + qrd The 'soc_version' and 'board_version' elements take the form of v<Major>.<Minor> where the minor number may be omitted when it's zero, i.e. v1.0 is the same @@ -102,14 +103,35 @@ properties: - const: qcom,msm8960 - items: + - enum: + - fairphone,fp2 + - lge,hammerhead + - sony,xperia-amami + - sony,xperia-castor + - sony,xperia-honami + - const: qcom,msm8974 + + - items: - const: qcom,msm8916-mtp/1 - const: qcom,msm8916-mtp - const: qcom,msm8916 - items: + - enum: + - longcheer,l8150 + - samsung,a3u-eur + - samsung,a5u-eur + - const: qcom,msm8916 + + - items: - const: qcom,msm8996-mtp - items: + - enum: + - qcom,ipq4019-ap-dk04.1-c3 + - qcom,ipq4019-ap-dk07.1-c1 + - qcom,ipq4019-ap-dk07.1-c2 + - qcom,ipq4019-dk04.1-c1 - const: qcom,ipq4019 - items: diff --git a/Documentation/devicetree/bindings/arm/rda.txt b/Documentation/devicetree/bindings/arm/rda.txt deleted file mode 100644 index 43c80762c428..000000000000 --- a/Documentation/devicetree/bindings/arm/rda.txt +++ /dev/null @@ -1,17 +0,0 @@ -RDA Micro platforms device tree bindings ----------------------------------------- - -RDA8810PL SoC -============= - -Required root node properties: - - - compatible : must contain "rda,8810pl" - - -Boards: - -Root node property compatible must contain, depending on board: - - - Orange Pi 2G-IoT: "xunlong,orangepi-2g-iot" - - Orange Pi i96: "xunlong,orangepi-i96" diff --git a/Documentation/devicetree/bindings/arm/rda.yaml b/Documentation/devicetree/bindings/arm/rda.yaml new file mode 100644 index 000000000000..51cec2b63b04 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/rda.yaml @@ -0,0 +1,20 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/rda.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: RDA Micro platforms device tree bindings + +maintainers: + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + +properties: + compatible: + items: + - enum: + - xunlong,orangepi-2g-iot # Orange Pi 2G-IoT + - xunlong,orangepi-i96 # Orange Pi i96 + - const: rda,8810pl + +... diff --git a/Documentation/devicetree/bindings/arm/realtek.txt b/Documentation/devicetree/bindings/arm/realtek.txt deleted file mode 100644 index 95839e19ae92..000000000000 --- a/Documentation/devicetree/bindings/arm/realtek.txt +++ /dev/null @@ -1,22 +0,0 @@ -Realtek platforms device tree bindings --------------------------------------- - - -RTD1295 SoC -=========== - -Required root node properties: - - - compatible : must contain "realtek,rtd1295" - - -Root node property compatible must contain, depending on board: - - - MeLE V9: "mele,v9" - - ProBox2 AVA: "probox2,ava" - - Zidoo X9S: "zidoo,x9s" - - -Example: - - compatible = "zidoo,x9s", "realtek,rtd1295"; diff --git a/Documentation/devicetree/bindings/arm/realtek.yaml b/Documentation/devicetree/bindings/arm/realtek.yaml new file mode 100644 index 000000000000..3528b61963b4 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/realtek.yaml @@ -0,0 +1,23 @@ +# SPDX-License-Identifier: GPL-2.0-or-later OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/realtek.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Realtek platforms device tree bindings + +maintainers: + - Andreas Färber <afaerber@suse.de> + +properties: + $nodename: + const: '/' + compatible: + # RTD1295 SoC based boards + items: + - enum: + - mele,v9 + - probox2,ava + - zidoo,x9s + - const: realtek,rtd1295 +... diff --git a/Documentation/devicetree/bindings/arm/renesas.yaml b/Documentation/devicetree/bindings/arm/renesas.yaml index 19f379863d50..28eb458f761a 100644 --- a/Documentation/devicetree/bindings/arm/renesas.yaml +++ b/Documentation/devicetree/bindings/arm/renesas.yaml @@ -1,7 +1,7 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: http://devicetree.org/schemas/arm/shmobile.yaml# +$id: http://devicetree.org/schemas/arm/renesas.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# title: Renesas SH-Mobile, R-Mobile, and R-Car Platform Device Tree Bindings @@ -106,6 +106,14 @@ properties: - description: RZ/G2M (R8A774A1) items: + - enum: + - hoperun,hihope-rzg2m # HopeRun HiHope RZ/G2M platform + - const: renesas,r8a774a1 + + - items: + - enum: + - hoperun,hihope-rzg2-ex # HopeRun expansion board for HiHope RZ/G2 platforms + - const: hoperun,hihope-rzg2m - const: renesas,r8a774a1 - description: RZ/G2E (R8A774C0) diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml index 5c6bbf10abc9..c82c5e57d44c 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.yaml +++ b/Documentation/devicetree/bindings/arm/rockchip.yaml @@ -128,6 +128,21 @@ properties: - const: google,veyron - const: rockchip,rk3288 + - description: Google Fievel (AOPEN Chromebox Mini) + items: + - const: google,veyron-fievel-rev8 + - const: google,veyron-fievel-rev7 + - const: google,veyron-fievel-rev6 + - const: google,veyron-fievel-rev5 + - const: google,veyron-fievel-rev4 + - const: google,veyron-fievel-rev3 + - const: google,veyron-fievel-rev2 + - const: google,veyron-fievel-rev1 + - const: google,veyron-fievel-rev0 + - const: google,veyron-fievel + - const: google,veyron + - const: rockchip,rk3288 + - description: Google Gru (dev-board) items: - const: google,gru-rev15 @@ -311,11 +326,49 @@ properties: - const: google,veyron - const: rockchip,rk3288 + - description: Google Tiger (AOpen Chromebase Mini) + items: + - const: google,veyron-tiger-rev8 + - const: google,veyron-tiger-rev7 + - const: google,veyron-tiger-rev6 + - const: google,veyron-tiger-rev5 + - const: google,veyron-tiger-rev4 + - const: google,veyron-tiger-rev3 + - const: google,veyron-tiger-rev2 + - const: google,veyron-tiger-rev1 + - const: google,veyron-tiger-rev0 + - const: google,veyron-tiger + - const: google,veyron + - const: rockchip,rk3288 + - description: Haoyu MarsBoard RK3066 items: - const: haoyu,marsboard-rk3066 - const: rockchip,rk3066a + - description: Hugsun X99 TV Box + items: + - const: hugsun,x99 + - const: rockchip,rk3399 + + - description: Khadas Edge series boards + items: + - enum: + - khadas,edge + - khadas,edge-captain + - khadas,edge-v + - const: rockchip,rk3399 + + - description: Mecer Xtreme Mini S6 + items: + - const: mecer,xms6 + - const: rockchip,rk3229 + + - description: Leez RK3399 P710 + items: + - const: leez,p710 + - const: rockchip,rk3399 + - description: mqmaker MiQi items: - const: mqmaker,miqi @@ -411,11 +464,6 @@ properties: - rockchip,rk3288-evb-rk808 - const: rockchip,rk3288 - - description: Rockchip RK3288 Fennec - items: - - const: rockchip,rk3288-fennec - - const: rockchip,rk3288 - - description: Rockchip RK3328 Evaluation board items: - const: rockchip,rk3328-evb diff --git a/Documentation/devicetree/bindings/arm/socionext/milbeaut.yaml b/Documentation/devicetree/bindings/arm/socionext/milbeaut.yaml index aae53fc3cb1e..2bd519d2e855 100644 --- a/Documentation/devicetree/bindings/arm/socionext/milbeaut.yaml +++ b/Documentation/devicetree/bindings/arm/socionext/milbeaut.yaml @@ -1,7 +1,7 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: http://devicetree.org/schemas/arm/milbeaut.yaml# +$id: http://devicetree.org/schemas/arm/socionext/milbeaut.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# title: Milbeaut platforms device tree bindings diff --git a/Documentation/devicetree/bindings/arm/stm32/mlahb.txt b/Documentation/devicetree/bindings/arm/stm32/mlahb.txt new file mode 100644 index 000000000000..25307aa1eb9b --- /dev/null +++ b/Documentation/devicetree/bindings/arm/stm32/mlahb.txt @@ -0,0 +1,37 @@ +ML-AHB interconnect bindings + +These bindings describe the STM32 SoCs ML-AHB interconnect bus which connects +a Cortex-M subsystem with dedicated memories. +The MCU SRAM and RETRAM memory parts can be accessed through different addresses +(see "RAM aliases" in [1]) using different buses (see [2]) : balancing the +Cortex-M firmware accesses among those ports allows to tune the system +performance. + +[1]: https://www.st.com/resource/en/reference_manual/dm00327659.pdf +[2]: https://wiki.st.com/stm32mpu/wiki/STM32MP15_RAM_mapping + +Required properties: +- compatible: should be "simple-bus" +- dma-ranges: describes memory addresses translation between the local CPU and + the remote Cortex-M processor. Each memory region, is declared with + 3 parameters: + - param 1: device base address (Cortex-M processor address) + - param 2: physical base address (local CPU address) + - param 3: size of the memory region. + +The Cortex-M remote processor accessed via the mlahb interconnect is described +by a child node. + +Example: +mlahb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + dma-ranges = <0x00000000 0x38000000 0x10000>, + <0x10000000 0x10000000 0x60000>, + <0x30000000 0x30000000 0x60000>; + + m4_rproc: m4@10000000 { + ... + }; +}; diff --git a/Documentation/devicetree/bindings/arm/stm32/stm32.txt b/Documentation/devicetree/bindings/arm/stm32/stm32.txt deleted file mode 100644 index 6808ed9ddfd5..000000000000 --- a/Documentation/devicetree/bindings/arm/stm32/stm32.txt +++ /dev/null @@ -1,10 +0,0 @@ -STMicroelectronics STM32 Platforms Device Tree Bindings - -Each device tree must specify which STM32 SoC it uses, -using one of the following compatible strings: - - st,stm32f429 - st,stm32f469 - st,stm32f746 - st,stm32h743 - st,stm32mp157 diff --git a/Documentation/devicetree/bindings/arm/stm32/stm32.yaml b/Documentation/devicetree/bindings/arm/stm32/stm32.yaml new file mode 100644 index 000000000000..4d194f1eb03a --- /dev/null +++ b/Documentation/devicetree/bindings/arm/stm32/stm32.yaml @@ -0,0 +1,31 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/stm32/stm32.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics STM32 Platforms Device Tree Bindings + +maintainers: + - Alexandre Torgue <alexandre.torgue@st.com> + +properties: + compatible: + oneOf: + - items: + - const: st,stm32f429 + + - items: + - const: st,stm32f469 + + - items: + - const: st,stm32f746 + + - items: + - const: st,stm32h743 + + - items: + - enum: + - arrow,stm32mp157a-avenger96 # Avenger96 + - const: st,stm32mp157 +... diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml index 285f4fc8519d..972b1e9ee804 100644 --- a/Documentation/devicetree/bindings/arm/sunxi.yaml +++ b/Documentation/devicetree/bindings/arm/sunxi.yaml @@ -263,7 +263,7 @@ properties: - description: ICNova A20 SWAC items: - - const: swac,icnova-a20-swac + - const: incircuit,icnova-a20-swac - const: incircuit,icnova-a20 - const: allwinner,sun7i-a20 @@ -353,6 +353,12 @@ properties: - const: licheepi,licheepi-zero - const: allwinner,sun8i-v3s + - description: Lichee Zero Plus (with S3, without eMMC/SPI Flash) + items: + - const: sipeed,lichee-zero-plus + - const: sochip,s3 + - const: allwinner,sun8i-v3 + - description: Linksprite PCDuino items: - const: linksprite,a10-pcduino @@ -568,6 +574,11 @@ properties: - const: olimex,a64-olinuxino - const: allwinner,sun50i-a64 + - description: Olimex A64-OlinuXino (with eMMC) + items: + - const: olimex,a64-olinuxino-emmc + - const: allwinner,sun50i-a64 + - description: Olimex A64 Teres-I items: - const: olimex,a64-teres-i @@ -671,6 +682,11 @@ properties: - const: sinlinx,sina33 - const: allwinner,sun8i-a33 + - description: Tanix TX6 + items: + - const: oranth,tanix-tx6 + - const: allwinner,sun50i-h6 + - description: TBS A711 Tablet items: - const: tbs-biometrics,a711 diff --git a/Documentation/devicetree/bindings/arm/ti/k3.txt b/Documentation/devicetree/bindings/arm/ti/k3.txt index 6a059cabb2da..333e7256126a 100644 --- a/Documentation/devicetree/bindings/arm/ti/k3.txt +++ b/Documentation/devicetree/bindings/arm/ti/k3.txt @@ -13,6 +13,9 @@ architecture it uses, using one of the following compatible values: - AM654 compatible = "ti,am654"; +- J721E + compatible = "ti,j721e"; + Boards ------ diff --git a/Documentation/devicetree/bindings/arm/ti/ti,davinci.yaml b/Documentation/devicetree/bindings/arm/ti/ti,davinci.yaml index 4326d2cfa15d..a8765ba29476 100644 --- a/Documentation/devicetree/bindings/arm/ti/ti,davinci.yaml +++ b/Documentation/devicetree/bindings/arm/ti/ti,davinci.yaml @@ -1,7 +1,7 @@ # SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- -$id: http://devicetree.org/schemas/arm/ti/davinci.yaml# +$id: http://devicetree.org/schemas/arm/ti/ti,davinci.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# title: Texas Instruments DaVinci Platforms Device Tree Bindings diff --git a/Documentation/devicetree/bindings/arm/xen.txt b/Documentation/devicetree/bindings/arm/xen.txt index c9b9321434ea..db5c56db30ec 100644 --- a/Documentation/devicetree/bindings/arm/xen.txt +++ b/Documentation/devicetree/bindings/arm/xen.txt @@ -54,7 +54,7 @@ hypervisor { }; The format and meaning of the "xen,uefi-*" parameters are similar to those in -Documentation/arm/uefi.txt, which are provided by the regular UEFI stub. However +Documentation/arm/uefi.rst, which are provided by the regular UEFI stub. However they differ because they are provided by the Xen hypervisor, together with a set of UEFI runtime services implemented via hypercalls, see http://xenbits.xen.org/docs/unstable/hypercall/x86_64/include,public,platform.h.html. diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt index e30fd106df4f..55c6fab1b373 100644 --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -45,7 +45,7 @@ Required properties when using sub-nodes: - #address-cells : number of cells to encode an address - #size-cells : number of cells representing the size of an address -For allwinner,sun8i-r40-ahci, the reset propertie must be present. +For allwinner,sun8i-r40-ahci, the reset property must be present. Sub-nodes required properties: - reg : the port number diff --git a/Documentation/devicetree/bindings/bus/allwinner,sun50i-a64-de2.yaml b/Documentation/devicetree/bindings/bus/allwinner,sun50i-a64-de2.yaml new file mode 100644 index 000000000000..d2a872286437 --- /dev/null +++ b/Documentation/devicetree/bindings/bus/allwinner,sun50i-a64-de2.yaml @@ -0,0 +1,85 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/bus/allwinner,sun50i-a64-de2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A64 Display Engine Bus Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + $nodename: + pattern: "^bus(@[0-9a-f]+)?$" + + "#address-cells": + const: 1 + + "#size-cells": + const: 1 + + compatible: + oneOf: + - const: allwinner,sun50i-a64-de2 + - items: + - const: allwinner,sun50i-h6-de3 + - const: allwinner,sun50i-a64-de2 + + reg: + maxItems: 1 + + allwinner,sram: + allOf: + - $ref: /schemas/types.yaml#definitions/phandle-array + - maxItems: 1 + description: + The SRAM that needs to be claimed to access the display engine + bus. + + ranges: true + +patternProperties: + # All other properties should be child nodes with unit-address and 'reg' + "^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}@[0-9a-fA-F]+$": + type: object + properties: + reg: + maxItems: 1 + + required: + - reg + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + - ranges + - allwinner,sram + +additionalProperties: false + +examples: + - | + bus@1000000 { + compatible = "allwinner,sun50i-a64-de2"; + reg = <0x1000000 0x400000>; + allwinner,sram = <&de2_sram 1>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x1000000 0x400000>; + + display_clocks: clock@0 { + compatible = "allwinner,sun50i-a64-de2-clk"; + reg = <0x0 0x100000>; + clocks = <&ccu 52>, <&ccu 99>; + clock-names = "bus", "mod"; + resets = <&ccu 30>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/bus/allwinner,sun8i-a23-rsb.yaml b/Documentation/devicetree/bindings/bus/allwinner,sun8i-a23-rsb.yaml new file mode 100644 index 000000000000..be32f087c529 --- /dev/null +++ b/Documentation/devicetree/bindings/bus/allwinner,sun8i-a23-rsb.yaml @@ -0,0 +1,80 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/bus/allwinner,sun8i-a23-rsb.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A23 RSB Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + compatible: + oneOf: + - const: allwinner,sun8i-a23-rsb + - items: + - const: allwinner,sun8i-a83t-rsb + - const: allwinner,sun8i-a23-rsb + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + clock-frequency: + minimum: 1 + maximum: 20000000 + +patternProperties: + "^.*@[0-9a-fA-F]+$": + type: object + properties: + reg: + maxItems: 1 + + required: + - reg + +required: + - compatible + - reg + - interrupts + - clocks + - resets + +examples: + - | + rsb@1f03400 { + compatible = "allwinner,sun8i-a23-rsb"; + reg = <0x01f03400 0x400>; + interrupts = <0 39 4>; + clocks = <&apb0_gates 3>; + clock-frequency = <3000000>; + resets = <&apb0_rst 3>; + #address-cells = <1>; + #size-cells = <0>; + + pmic@3e3 { + compatible = "..."; + reg = <0x3e3>; + + /* ... */ + }; + }; + +additionalProperties: false diff --git a/Documentation/devicetree/bindings/bus/imx-weim.txt b/Documentation/devicetree/bindings/bus/imx-weim.txt index dda7d6d66479..1b1d1c5c21ea 100644 --- a/Documentation/devicetree/bindings/bus/imx-weim.txt +++ b/Documentation/devicetree/bindings/bus/imx-weim.txt @@ -44,6 +44,10 @@ Optional properties: what bootloader sets up in IOMUXC_GPR1[11:0] will be used. + - fsl,burst-clk-enable For "fsl,imx50-weim" and "fsl,imx6q-weim" type of + devices, the presence of this property indicates that + the weim bus should operate in Burst Clock Mode. + Timing property for child nodes. It is mandatory, not optional. - fsl,weim-cs-timing: The timing array, contains timing values for the diff --git a/Documentation/devicetree/bindings/bus/moxtet.txt b/Documentation/devicetree/bindings/bus/moxtet.txt new file mode 100644 index 000000000000..fb50fc865336 --- /dev/null +++ b/Documentation/devicetree/bindings/bus/moxtet.txt @@ -0,0 +1,46 @@ +Turris Mox module status and configuration bus (over SPI) + +Required properties: + - compatible : Should be "cznic,moxtet" + - #address-cells : Has to be 1 + - #size-cells : Has to be 0 + - spi-cpol : Required inverted clock polarity + - spi-cpha : Required shifted clock phase + - interrupts : Must contain reference to the shared interrupt line + - interrupt-controller : Required + - #interrupt-cells : Has to be 1 + +For other required and optional properties of SPI slave nodes please refer to +../spi/spi-bus.txt. + +Required properties of subnodes: + - reg : Should be position on the Moxtet bus (how many Moxtet + modules are between this module and CPU module, so + either 0 or a positive integer) + +The driver finds the devices connected to the bus by itself, but it may be +needed to reference some of them from other parts of the device tree. In that +case the devices can be defined as subnodes of the moxtet node. + +Example: + + moxtet@1 { + compatible = "cznic,moxtet"; + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + spi-max-frequency = <10000000>; + spi-cpol; + spi-cpha; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gpiosb>; + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; + + moxtet_sfp: gpio@0 { + compatible = "cznic,moxtet-gpio"; + gpio-controller; + #gpio-cells = <2>; + reg = <0>; + } + }; diff --git a/Documentation/devicetree/bindings/bus/qcom,ebi2.txt b/Documentation/devicetree/bindings/bus/qcom,ebi2.txt index 5a7d567f6833..5058aa2c63b2 100644 --- a/Documentation/devicetree/bindings/bus/qcom,ebi2.txt +++ b/Documentation/devicetree/bindings/bus/qcom,ebi2.txt @@ -71,7 +71,7 @@ Optional subnodes: The following optional properties are properties that can be tagged onto any device subnode. We are assuming that there can be only ONE device per -chipselect subnode, else the properties will become ambigous. +chipselect subnode, else the properties will become ambiguous. Optional properties arrays for SLOW chip selects: - qcom,xmem-recovery-cycles: recovery cycles is the time the memory continues to diff --git a/Documentation/devicetree/bindings/bus/sun50i-de2-bus.txt b/Documentation/devicetree/bindings/bus/sun50i-de2-bus.txt deleted file mode 100644 index b9d533717dff..000000000000 --- a/Documentation/devicetree/bindings/bus/sun50i-de2-bus.txt +++ /dev/null @@ -1,40 +0,0 @@ -Device tree bindings for Allwinner DE2/3 bus - -The Allwinner A64 DE2 is on a special bus, which needs a SRAM region (SRAM C) -to be claimed for enabling the access. The DE3 on Allwinner H6 is at the same -situation, and the binding also applies. - -Required properties: - - - compatible: Should be one of: - - "allwinner,sun50i-a64-de2" - - "allwinner,sun50i-h6-de3", "allwinner,sun50i-a64-de2" - - reg: A resource specifier for the register space - - #address-cells: Must be set to 1 - - #size-cells: Must be set to 1 - - ranges: Must be set up to map the address space inside the - DE2, for the sub-blocks of DE2. - - allwinner,sram: the SRAM that needs to be claimed - -Example: - - de2@1000000 { - compatible = "allwinner,sun50i-a64-de2"; - reg = <0x1000000 0x400000>; - allwinner,sram = <&de2_sram 1>; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0x1000000 0x400000>; - - display_clocks: clock@0 { - compatible = "allwinner,sun50i-a64-de2-clk"; - reg = <0x0 0x100000>; - clocks = <&ccu CLK_DE>, - <&ccu CLK_BUS_DE>; - clock-names = "mod", - "bus"; - resets = <&ccu RST_BUS_DE>; - #clock-cells = <1>; - #reset-cells = <1>; - }; - }; diff --git a/Documentation/devicetree/bindings/bus/sunxi-rsb.txt b/Documentation/devicetree/bindings/bus/sunxi-rsb.txt deleted file mode 100644 index eb3ed628c6f1..000000000000 --- a/Documentation/devicetree/bindings/bus/sunxi-rsb.txt +++ /dev/null @@ -1,47 +0,0 @@ -Allwinner Reduced Serial Bus (RSB) controller - -The RSB controller found on later Allwinner SoCs is an SMBus like 2 wire -serial bus with 1 master and up to 15 slaves. It is represented by a node -for the controller itself, and child nodes representing the slave devices. - -Required properties : - - - reg : Offset and length of the register set for the controller. - - compatible : Shall be "allwinner,sun8i-a23-rsb". - - interrupts : The interrupt line associated to the RSB controller. - - clocks : The gate clk associated to the RSB controller. - - resets : The reset line associated to the RSB controller. - - #address-cells : shall be 1 - - #size-cells : shall be 0 - -Optional properties : - - - clock-frequency : Desired RSB bus clock frequency in Hz. Maximum is 20MHz. - If not set this defaults to 3MHz. - -Child nodes: - -An RSB controller node can contain zero or more child nodes representing -slave devices on the bus. Child 'reg' properties should contain the slave -device's hardware address. The hardware address is hardwired in the device, -which can normally be found in the datasheet. - -Example: - - rsb@1f03400 { - compatible = "allwinner,sun8i-a23-rsb"; - reg = <0x01f03400 0x400>; - interrupts = <0 39 4>; - clocks = <&apb0_gates 3>; - clock-frequency = <3000000>; - resets = <&apb0_rst 3>; - #address-cells = <1>; - #size-cells = <0>; - - pmic@3e3 { - compatible = "..."; - reg = <0x3e3>; - - /* ... */ - }; - }; diff --git a/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml b/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml new file mode 100644 index 000000000000..64938fdaea55 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml @@ -0,0 +1,142 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/allwinner,sun4i-a10-ccu.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner Clock Control Unit Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + "#clock-cells": + const: 1 + + "#reset-cells": + const: 1 + + compatible: + enum: + - allwinner,sun4i-a10-ccu + - allwinner,sun5i-a10s-ccu + - allwinner,sun5i-a13-ccu + - allwinner,sun6i-a31-ccu + - allwinner,sun7i-a20-ccu + - allwinner,sun8i-a23-ccu + - allwinner,sun8i-a33-ccu + - allwinner,sun8i-a83t-ccu + - allwinner,sun8i-a83t-r-ccu + - allwinner,sun8i-h3-ccu + - allwinner,sun8i-h3-r-ccu + - allwinner,sun8i-r40-ccu + - allwinner,sun8i-v3-ccu + - allwinner,sun8i-v3s-ccu + - allwinner,sun9i-a80-ccu + - allwinner,sun50i-a64-ccu + - allwinner,sun50i-a64-r-ccu + - allwinner,sun50i-h5-ccu + - allwinner,sun50i-h6-ccu + - allwinner,sun50i-h6-r-ccu + - allwinner,suniv-f1c100s-ccu + - nextthing,gr8-ccu + + reg: + maxItems: 1 + + clocks: + minItems: 2 + maxItems: 4 + items: + - description: High Frequency Oscillator (usually at 24MHz) + - description: Low Frequency Oscillator (usually at 32kHz) + - description: Internal Oscillator + - description: Peripherals PLL + + clock-names: + minItems: 2 + maxItems: 4 + items: + - const: hosc + - const: losc + - const: iosc + - const: pll-periph + +required: + - "#clock-cells" + - "#reset-cells" + - compatible + - reg + - clocks + - clock-names + +if: + properties: + compatible: + enum: + - allwinner,sun8i-a83t-r-ccu + - allwinner,sun8i-h3-r-ccu + - allwinner,sun50i-a64-r-ccu + - allwinner,sun50i-h6-r-ccu + +then: + properties: + clocks: + minItems: 4 + maxItems: 4 + + clock-names: + minItems: 4 + maxItems: 4 + +else: + if: + properties: + compatible: + const: allwinner,sun50i-h6-ccu + + then: + properties: + clocks: + minItems: 3 + maxItems: 3 + + clock-names: + minItems: 3 + maxItems: 3 + + else: + properties: + clocks: + minItems: 2 + maxItems: 2 + + clock-names: + minItems: 2 + maxItems: 2 + +additionalProperties: false + +examples: + - | + ccu: clock@1c20000 { + compatible = "allwinner,sun8i-h3-ccu"; + reg = <0x01c20000 0x400>; + clocks = <&osc24M>, <&osc32k>; + clock-names = "hosc", "losc"; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + - | + r_ccu: clock@1f01400 { + compatible = "allwinner,sun50i-a64-r-ccu"; + reg = <0x01f01400 0x100>; + clocks = <&osc24M>, <&osc32k>, <&iosc>, <&ccu 11>; + clock-names = "hosc", "losc", "iosc", "pll-periph"; + #clock-cells = <1>; + #reset-cells = <1>; + }; + +... diff --git a/Documentation/devicetree/bindings/clock/amlogic,axg-audio-clkc.txt b/Documentation/devicetree/bindings/clock/amlogic,axg-audio-clkc.txt index 0f777749f4f1..b3957d10d241 100644 --- a/Documentation/devicetree/bindings/clock/amlogic,axg-audio-clkc.txt +++ b/Documentation/devicetree/bindings/clock/amlogic,axg-audio-clkc.txt @@ -22,6 +22,7 @@ Required Properties: components. - resets : phandle of the internal reset line - #clock-cells : should be 1. +- #reset-cells : should be 1 on the g12a (and following) soc family Each clock is assigned an identifier and client nodes can use this identifier to specify the clock which they consume. All available clocks are defined as diff --git a/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt index 5c8b105be4d6..7ccecd5c02c1 100644 --- a/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt +++ b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt @@ -10,6 +10,8 @@ Required Properties: "amlogic,gxl-clkc" for GXL and GXM SoC, "amlogic,axg-clkc" for AXG SoC. "amlogic,g12a-clkc" for G12A SoC. + "amlogic,g12b-clkc" for G12B SoC. + "amlogic,sm1-clkc" for SM1 SoC. - clocks : list of clock phandle, one for each entry clock-names. - clock-names : should contain the following: * "xtal": the platform xtal diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt index b520280e33ff..13f45db3b66d 100644 --- a/Documentation/devicetree/bindings/clock/at91-clock.txt +++ b/Documentation/devicetree/bindings/clock/at91-clock.txt @@ -9,10 +9,11 @@ Slow Clock controller: Required properties: - compatible : shall be one of the following: "atmel,at91sam9x5-sckc", - "atmel,sama5d3-sckc" or - "atmel,sama5d4-sckc": + "atmel,sama5d3-sckc", + "atmel,sama5d4-sckc" or + "microchip,sam9x60-sckc": at91 SCKC (Slow Clock Controller) -- #clock-cells : shall be 0. +- #clock-cells : shall be 1 for "microchip,sam9x60-sckc" otherwise shall be 0. - clocks : shall be the input parent clock phandle for the clock. Optional properties: diff --git a/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt b/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt index dd906db34b32..9e0b03a6519b 100644 --- a/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt +++ b/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt @@ -12,7 +12,9 @@ clock generators, but a few (like the ARM or HDMI) will source from the PLL dividers directly. Required properties: -- compatible: Should be "brcm,bcm2835-cprman" +- compatible: should be one of the following, + "brcm,bcm2711-cprman" + "brcm,bcm2835-cprman" - #clock-cells: Should be <1>. The permitted clock-specifier values can be found in include/dt-bindings/clock/bcm2835.h - reg: Specifies base physical address and size of the registers diff --git a/Documentation/devicetree/bindings/clock/brcm,bcm63xx-clocks.txt b/Documentation/devicetree/bindings/clock/brcm,bcm63xx-clocks.txt new file mode 100644 index 000000000000..3041657e2f96 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/brcm,bcm63xx-clocks.txt @@ -0,0 +1,22 @@ +Gated Clock Controller Bindings for MIPS based BCM63XX SoCs + +Required properties: +- compatible: must be one of: + "brcm,bcm3368-clocks" + "brcm,bcm6328-clocks" + "brcm,bcm6358-clocks" + "brcm,bcm6362-clocks" + "brcm,bcm6368-clocks" + "brcm,bcm63268-clocks" + +- reg: Address and length of the register set +- #clock-cells: must be <1> + + +Example: + +clkctl: clock-controller@10000004 { + compatible = "brcm,bcm6328-clocks"; + reg = <0x10000004 0x4>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt b/Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt index b8d8ef3bdc5f..52a064c789ee 100644 --- a/Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt +++ b/Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt @@ -40,6 +40,7 @@ Optional properties: input audio clocks from host system. - ln-psia1-mclk, ln-psia2-mclk : Optional input audio clocks from external connector. + - ln-spdif-mclk : Optional input audio clock from SPDIF. - ln-spdif-clkout : Optional input audio clock from SPDIF. - ln-adat-mclk : Optional input audio clock from ADAT. - ln-pmic-32k : On board fixed clock. diff --git a/Documentation/devicetree/bindings/clock/imx8mn-clock.yaml b/Documentation/devicetree/bindings/clock/imx8mn-clock.yaml new file mode 100644 index 000000000000..622f3658bd9f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx8mn-clock.yaml @@ -0,0 +1,112 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/bindings/clock/imx8mn-clock.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP i.MX8M Nano Clock Control Module Binding + +maintainers: + - Anson Huang <Anson.Huang@nxp.com> + +description: | + NXP i.MX8M Nano clock control module is an integrated clock controller, which + generates and supplies to all modules. + +properties: + compatible: + const: fsl,imx8mn-ccm + + reg: + maxItems: 1 + + clocks: + items: + - description: 32k osc + - description: 24m osc + - description: ext1 clock input + - description: ext2 clock input + - description: ext3 clock input + - description: ext4 clock input + + clock-names: + items: + - const: osc_32k + - const: osc_24m + - const: clk_ext1 + - const: clk_ext2 + - const: clk_ext3 + - const: clk_ext4 + + '#clock-cells': + const: 1 + description: | + The clock consumer should specify the desired clock by having the clock + ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx8mn-clock.h + for the full list of i.MX8M Nano clock IDs. + +required: + - compatible + - reg + - clocks + - clock-names + - '#clock-cells' + +examples: + # Clock Control Module node: + - | + clk: clock-controller@30380000 { + compatible = "fsl,imx8mn-ccm"; + reg = <0x0 0x30380000 0x0 0x10000>; + #clock-cells = <1>; + clocks = <&osc_32k>, <&osc_24m>, <&clk_ext1>, + <&clk_ext2>, <&clk_ext3>, <&clk_ext4>; + clock-names = "osc_32k", "osc_24m", "clk_ext1", + "clk_ext2", "clk_ext3", "clk_ext4"; + }; + + # Required external clocks for Clock Control Module node: + - | + osc_32k: clock-osc-32k { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "osc_32k"; + }; + + osc_24m: clock-osc-24m { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24000000>; + clock-output-names = "osc_24m"; + }; + + clk_ext1: clock-ext1 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <133000000>; + clock-output-names = "clk_ext1"; + }; + + clk_ext2: clock-ext2 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <133000000>; + clock-output-names = "clk_ext2"; + }; + + clk_ext3: clock-ext3 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <133000000>; + clock-output-names = "clk_ext3"; + }; + + clk_ext4: clock-ext4 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency= <133000000>; + clock-output-names = "clk_ext4"; + }; + +... diff --git a/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt index 796c260c183d..d8f5c490f893 100644 --- a/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt +++ b/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt @@ -59,6 +59,7 @@ Required properties: "marvell,dove-core-clock" - for Dove SoC core clocks "marvell,kirkwood-core-clock" - for Kirkwood SoC (except mv88f6180) "marvell,mv88f6180-core-clock" - for Kirkwood MV88f6180 SoC + "marvell,mv98dx1135-core-clock" - for Kirkwood 98dx1135 SoC "marvell,mv88f5181-core-clock" - for Orion MV88F5181 SoC "marvell,mv88f5182-core-clock" - for Orion MV88F5182 SoC "marvell,mv88f5281-core-clock" - for Orion MV88F5281 SoC diff --git a/Documentation/devicetree/bindings/clock/qcom,gcc.txt b/Documentation/devicetree/bindings/clock/qcom,gcc.txt index 8661c3cd3ccf..d14362ad4132 100644 --- a/Documentation/devicetree/bindings/clock/qcom,gcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,gcc.txt @@ -23,6 +23,7 @@ Required properties : "qcom,gcc-sdm630" "qcom,gcc-sdm660" "qcom,gcc-sdm845" + "qcom,gcc-sm8150" - reg : shall contain base register location and length - #clock-cells : shall contain 1 @@ -38,6 +39,13 @@ Documentation/devicetree/bindings/thermal/qcom-tsens.txt - protected-clocks : Protected clock specifier list as per common clock binding. +For SM8150 only: + - clocks: a list of phandles and clock-specifier pairs, + one for each entry in clock-names. + - clock-names: "bi_tcxo" (required) + "sleep_clk" (optional) + "aud_ref_clock" (optional) + Example: clock-controller@900000 { compatible = "qcom,gcc-msm8960"; @@ -71,3 +79,16 @@ Example of GCC with protected-clocks properties: <GCC_LPASS_Q6_AXI_CLK>, <GCC_LPASS_SWAY_CLK>; }; + +Example of GCC with clocks + gcc: clock-controller@100000 { + compatible = "qcom,gcc-sm8150"; + reg = <0x00100000 0x1f0000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + clock-names = "bi_tcxo", + "sleep_clk"; + clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>, + <&sleep_clk>; + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,gpucc.txt b/Documentation/devicetree/bindings/clock/qcom,gpucc.txt index 4e5215ef1acd..269afe8a757e 100644 --- a/Documentation/devicetree/bindings/clock/qcom,gpucc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,gpucc.txt @@ -2,13 +2,15 @@ Qualcomm Graphics Clock & Reset Controller Binding -------------------------------------------------- Required properties : -- compatible : shall contain "qcom,sdm845-gpucc" +- compatible : shall contain "qcom,sdm845-gpucc" or "qcom,msm8998-gpucc" - reg : shall contain base register location and length - #clock-cells : from common clock binding, shall contain 1 - #reset-cells : from common reset binding, shall contain 1 - #power-domain-cells : from generic power domain binding, shall contain 1 - clocks : shall contain the XO clock + shall contain the gpll0 out main clock (msm8998) - clock-names : shall be "xo" + shall be "gpll0" (msm8998) Example: gpucc: clock-controller@5090000 { diff --git a/Documentation/devicetree/bindings/clock/qcom,rpmh-clk.txt b/Documentation/devicetree/bindings/clock/qcom,rpmh-clk.txt index 3c007653da31..365bbde599b1 100644 --- a/Documentation/devicetree/bindings/clock/qcom,rpmh-clk.txt +++ b/Documentation/devicetree/bindings/clock/qcom,rpmh-clk.txt @@ -6,9 +6,14 @@ some Qualcomm Technologies Inc. SoCs. It accepts clock requests from other hardware subsystems via RSC to control clocks. Required properties : -- compatible : shall contain "qcom,sdm845-rpmh-clk" +- compatible : must be one of: + "qcom,sdm845-rpmh-clk" + "qcom,sm8150-rpmh-clk" - #clock-cells : must contain 1 +- clocks: a list of phandles and clock-specifier pairs, + one for each entry in clock-names. +- clock-names: Parent board clock: "xo". Example : diff --git a/Documentation/devicetree/bindings/clock/emev2-clock.txt b/Documentation/devicetree/bindings/clock/renesas,emev2-smu.txt index 268ca615459e..268ca615459e 100644 --- a/Documentation/devicetree/bindings/clock/emev2-clock.txt +++ b/Documentation/devicetree/bindings/clock/renesas,emev2-smu.txt diff --git a/Documentation/devicetree/bindings/clock/renesas,r9a06g032-sysctrl.txt b/Documentation/devicetree/bindings/clock/renesas,r9a06g032-sysctrl.txt index d60b99756bb9..aed713cf0831 100644 --- a/Documentation/devicetree/bindings/clock/renesas,r9a06g032-sysctrl.txt +++ b/Documentation/devicetree/bindings/clock/renesas,r9a06g032-sysctrl.txt @@ -13,6 +13,7 @@ Required Properties: - external (optional) RGMII_REFCLK - clock-names: Must be: clock-names = "mclk", "rtc", "jtag", "rgmii_ref_ext"; + - #power-domain-cells: Must be 0 Examples -------- @@ -27,6 +28,7 @@ Examples clocks = <&ext_mclk>, <&ext_rtc_clk>, <&ext_jtag_clk>, <&ext_rgmii_ref>; clock-names = "mclk", "rtc", "jtag", "rgmii_ref_ext"; + #power-domain-cells = <0>; }; - Other nodes can use the clocks provided by SYSCTRL as in: @@ -38,6 +40,7 @@ Examples interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; reg-shift = <2>; reg-io-width = <4>; - clocks = <&sysctrl R9A06G032_CLK_UART0>; - clock-names = "baudclk"; + clocks = <&sysctrl R9A06G032_CLK_UART0>, <&sysctrl R9A06G032_HCLK_UART0>; + clock-names = "baudclk", "apb_pclk"; + power-domains = <&sysctrl>; }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3308-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3308-cru.txt new file mode 100644 index 000000000000..9b151c5b0c90 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3308-cru.txt @@ -0,0 +1,60 @@ +* Rockchip RK3308 Clock and Reset Unit + +The RK3308 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: CRU should be "rockchip,rk3308-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing, pll rates are not changeable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3308-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "xin32k" - rtc clock - optional, + - "mclk_i2s0_8ch_in", "mclk_i2s1_8ch_in", "mclk_i2s2_8ch_in", + "mclk_i2s3_8ch_in", "mclk_i2s0_2ch_in", + "mclk_i2s1_2ch_in" - external I2S or SPDIF clock - optional, + - "mac_clkin" - external MAC clock - optional + +Example: Clock controller node: + + cru: clock-controller@ff500000 { + compatible = "rockchip,rk3308-cru"; + reg = <0x0 0xff500000 0x0 0x1000>; + rockchip,grf = <&grf>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@ff0a0000 { + compatible = "rockchip,rk3308-uart", "snps,dw-apb-uart"; + reg = <0x0 0xff0a0000 0x0 0x100>; + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>; + clock-names = "baudclk", "apb_pclk"; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/silabs,si5341.txt b/Documentation/devicetree/bindings/clock/silabs,si5341.txt new file mode 100644 index 000000000000..a70c333e4cd4 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/silabs,si5341.txt @@ -0,0 +1,162 @@ +Binding for Silicon Labs Si5341 and Si5340 programmable i2c clock generator. + +Reference +[1] Si5341 Data Sheet + https://www.silabs.com/documents/public/data-sheets/Si5341-40-D-DataSheet.pdf +[2] Si5341 Reference Manual + https://www.silabs.com/documents/public/reference-manuals/Si5341-40-D-RM.pdf + +The Si5341 and Si5340 are programmable i2c clock generators with up to 10 output +clocks. The chip contains a PLL that sources 5 (or 4) multisynth clocks, which +in turn can be directed to any of the 10 (or 4) outputs through a divider. +The internal structure of the clock generators can be found in [2]. + +The driver can be used in "as is" mode, reading the current settings from the +chip at boot, in case you have a (pre-)programmed device. If the PLL is not +configured when the driver probes, it assumes the driver must fully initialize +it. + +The device type, speed grade and revision are determined runtime by probing. + +The driver currently only supports XTAL input mode, and does not support any +fancy input configurations. They can still be programmed into the chip and +the driver will leave them "as is". + +==I2C device node== + +Required properties: +- compatible: shall be one of the following: + "silabs,si5340" - Si5340 A/B/C/D + "silabs,si5341" - Si5341 A/B/C/D +- reg: i2c device address, usually 0x74 +- #clock-cells: from common clock binding; shall be set to 2. + The first value is "0" for outputs, "1" for synthesizers. + The second value is the output or synthesizer index. +- clocks: from common clock binding; list of parent clock handles, + corresponding to inputs. Use a fixed clock for the "xtal" input. + At least one must be present. +- clock-names: One of: "xtal", "in0", "in1", "in2" +- vdd-supply: Regulator node for VDD + +Optional properties: +- vdda-supply: Regulator node for VDDA +- vdds-supply: Regulator node for VDDS +- silabs,pll-m-num, silabs,pll-m-den: Numerator and denominator for PLL + feedback divider. Must be such that the PLL output is in the valid range. For + example, to create 14GHz from a 48MHz xtal, use m-num=14000 and m-den=48. Only + the fraction matters, using 3500 and 12 will deliver the exact same result. + If these are not specified, and the PLL is not yet programmed when the driver + probes, the PLL will be set to 14GHz. +- silabs,reprogram: When present, the driver will always assume the device must + be initialized, and always performs the soft-reset routine. Since this will + temporarily stop all output clocks, don't do this if the chip is generating + the CPU clock for example. +- interrupts: Interrupt for INTRb pin. +- #address-cells: shall be set to 1. +- #size-cells: shall be set to 0. + + +== Child nodes: Outputs == + +The child nodes list the output clocks. + +Each of the clock outputs can be overwritten individually by using a child node. +If a child node for a clock output is not set, the configuration remains +unchanged. + +Required child node properties: +- reg: number of clock output. + +Optional child node properties: +- vdd-supply: Regulator node for VDD for this output. The driver selects default + values for common-mode and amplitude based on the voltage. +- silabs,format: Output format, one of: + 1 = differential (defaults to LVDS levels) + 2 = low-power (defaults to HCSL levels) + 4 = LVCMOS +- silabs,common-mode: Manually override output common mode, see [2] for values +- silabs,amplitude: Manually override output amplitude, see [2] for values +- silabs,synth-master: boolean. If present, this output is allowed to change the + multisynth frequency dynamically. +- silabs,silabs,disable-high: boolean. If set, the clock output is driven HIGH + when disabled, otherwise it's driven LOW. + +==Example== + +/* 48MHz reference crystal */ +ref48: ref48M { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <48000000>; +}; + +i2c-master-node { + /* Programmable clock (for logic) */ + si5341: clock-generator@74 { + reg = <0x74>; + compatible = "silabs,si5341"; + #clock-cells = <2>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&ref48>; + clock-names = "xtal"; + + silabs,pll-m-num = <14000>; /* PLL at 14.0 GHz */ + silabs,pll-m-den = <48>; + silabs,reprogram; /* Chips are not programmed, always reset */ + + out@0 { + reg = <0>; + silabs,format = <1>; /* LVDS 3v3 */ + silabs,common-mode = <3>; + silabs,amplitude = <3>; + silabs,synth-master; + }; + + /* + * Output 6 configuration: + * LVDS 1v8 + */ + out@6 { + reg = <6>; + silabs,format = <1>; /* LVDS 1v8 */ + silabs,common-mode = <13>; + silabs,amplitude = <3>; + }; + + /* + * Output 8 configuration: + * HCSL 3v3 + */ + out@8 { + reg = <8>; + silabs,format = <2>; + silabs,common-mode = <11>; + silabs,amplitude = <3>; + }; + }; +}; + +some-video-node { + /* Standard clock bindings */ + clock-names = "pixel"; + clocks = <&si5341 0 7>; /* Output 7 */ + + /* Set output 7 to use syntesizer 3 as its parent */ + assigned-clocks = <&si5341 0 7>, <&si5341 1 3>; + assigned-clock-parents = <&si5341 1 3>; + /* Set output 7 to 148.5 MHz using a synth frequency of 594 MHz */ + assigned-clock-rates = <148500000>, <594000000>; +}; + +some-audio-node { + clock-names = "i2s-clk"; + clocks = <&si5341 0 0>; + /* + * since output 0 is a synth-master, the synth will be automatically set + * to an appropriate frequency when the audio driver requests another + * frequency. We give control over synth 2 to this output here. + */ + assigned-clocks = <&si5341 0 0>; + assigned-clock-parents = <&si5341 1 2>; +}; diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt deleted file mode 100644 index e3bd88ae456b..000000000000 --- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt +++ /dev/null @@ -1,62 +0,0 @@ -Allwinner Clock Control Unit Binding ------------------------------------- - -Required properties : -- compatible: must contain one of the following compatibles: - - "allwinner,sun4i-a10-ccu" - - "allwinner,sun5i-a10s-ccu" - - "allwinner,sun5i-a13-ccu" - - "allwinner,sun6i-a31-ccu" - - "allwinner,sun7i-a20-ccu" - - "allwinner,sun8i-a23-ccu" - - "allwinner,sun8i-a33-ccu" - - "allwinner,sun8i-a83t-ccu" - - "allwinner,sun8i-a83t-r-ccu" - - "allwinner,sun8i-h3-ccu" - - "allwinner,sun8i-h3-r-ccu" -+ - "allwinner,sun8i-r40-ccu" - - "allwinner,sun8i-v3s-ccu" - - "allwinner,sun9i-a80-ccu" - - "allwinner,sun50i-a64-ccu" - - "allwinner,sun50i-a64-r-ccu" - - "allwinner,sun50i-h5-ccu" - - "allwinner,sun50i-h6-ccu" - - "allwinner,sun50i-h6-r-ccu" - - "allwinner,suniv-f1c100s-ccu" - - "nextthing,gr8-ccu" - -- reg: Must contain the registers base address and length -- clocks: phandle to the oscillators feeding the CCU. Two are needed: - - "hosc": the high frequency oscillator (usually at 24MHz) - - "losc": the low frequency oscillator (usually at 32kHz) - On the A83T, this is the internal 16MHz oscillator divided by 512 -- clock-names: Must contain the clock names described just above -- #clock-cells : must contain 1 -- #reset-cells : must contain 1 - -For the main CCU on H6, one more clock is needed: -- "iosc": the SoC's internal frequency oscillator - -For the PRCM CCUs on A83T/H3/A64/H6, two more clocks are needed: -- "pll-periph": the SoC's peripheral PLL from the main CCU -- "iosc": the SoC's internal frequency oscillator - -Example for generic CCU: -ccu: clock@1c20000 { - compatible = "allwinner,sun8i-h3-ccu"; - reg = <0x01c20000 0x400>; - clocks = <&osc24M>, <&osc32k>; - clock-names = "hosc", "losc"; - #clock-cells = <1>; - #reset-cells = <1>; -}; - -Example for PRCM CCU: -r_ccu: clock@1f01400 { - compatible = "allwinner,sun50i-a64-r-ccu"; - reg = <0x01f01400 0x100>; - clocks = <&osc24M>, <&osc32k>, <&iosc>, <&ccu CLK_PLL_PERIPH0>; - clock-names = "hosc", "losc", "iosc", "pll-periph"; - #clock-cells = <1>; - #reset-cells = <1>; -}; diff --git a/Documentation/devicetree/bindings/clock/ti,cdce925.txt b/Documentation/devicetree/bindings/clock/ti,cdce925.txt index 0d01f2d5cc36..26544c85202a 100644 --- a/Documentation/devicetree/bindings/clock/ti,cdce925.txt +++ b/Documentation/devicetree/bindings/clock/ti,cdce925.txt @@ -24,6 +24,8 @@ Required properties: Optional properties: - xtal-load-pf: Crystal load-capacitor value to fine-tune performance on a board, or to compensate for external influences. +- vdd-supply: A regulator node for Vdd +- vddout-supply: A regulator node for Vddout For all PLL1, PLL2, ... an optional child node can be used to specify spread spectrum clocking parameters for a board. @@ -41,6 +43,8 @@ Example: clocks = <&xtal_27Mhz>; #clock-cells = <1>; xtal-load-pf = <5>; + vdd-supply = <&1v8-reg>; + vddout-supply = <&3v3-reg>; /* PLL options to get SSC 1% centered */ PLL2 { spread-spectrum = <4>; diff --git a/Documentation/devicetree/bindings/common-properties.txt b/Documentation/devicetree/bindings/common-properties.txt index a3448bfa1c82..98a28130e100 100644 --- a/Documentation/devicetree/bindings/common-properties.txt +++ b/Documentation/devicetree/bindings/common-properties.txt @@ -5,30 +5,29 @@ Endianness ---------- The Devicetree Specification does not define any properties related to hardware -byteswapping, but endianness issues show up frequently in porting Linux to +byte swapping, but endianness issues show up frequently in porting drivers to different machine types. This document attempts to provide a consistent -way of handling byteswapping across drivers. +way of handling byte swapping across drivers. Optional properties: - big-endian: Boolean; force big endian register accesses unconditionally (e.g. ioread32be/iowrite32be). Use this if you - know the peripheral always needs to be accessed in BE mode. + know the peripheral always needs to be accessed in big endian (BE) mode. - little-endian: Boolean; force little endian register accesses unconditionally (e.g. readl/writel). Use this if you know the - peripheral always needs to be accessed in LE mode. + peripheral always needs to be accessed in little endian (LE) mode. - native-endian: Boolean; always use register accesses matched to the endianness of the kernel binary (e.g. LE vmlinux -> readl/writel, - BE vmlinux -> ioread32be/iowrite32be). In this case no byteswaps + BE vmlinux -> ioread32be/iowrite32be). In this case no byte swaps will ever be performed. Use this if the hardware "self-adjusts" register endianness based on the CPU's configured endianness. If a binding supports these properties, then the binding should also specify the default behavior if none of these properties are present. In such cases, little-endian is the preferred default, but it is not -a requirement. The of_device_is_big_endian() and of_fdt_is_big_endian() -helper functions do assume that little-endian is the default, because -most existing (PCI-based) drivers implicitly default to LE by using -readl/writel for MMIO accesses. +a requirement. Some implementations assume that little-endian is +the default, because most existing (PCI-based) drivers implicitly +default to LE for their MMIO accesses. Examples: Scenario 1 : CPU in LE mode & device in LE mode. diff --git a/Documentation/devicetree/bindings/connector/usb-connector.txt b/Documentation/devicetree/bindings/connector/usb-connector.txt index cef556d4e5ee..d357987181ee 100644 --- a/Documentation/devicetree/bindings/connector/usb-connector.txt +++ b/Documentation/devicetree/bindings/connector/usb-connector.txt @@ -17,6 +17,20 @@ Optional properties: - self-powered: Set this property if the usb device that has its own power source. +Optional properties for usb-b-connector: +- id-gpios: an input gpio for USB ID pin. +- vbus-gpios: an input gpio for USB VBUS pin, used to detect presence of + VBUS 5V. + see gpio/gpio.txt. +- vbus-supply: a phandle to the regulator for USB VBUS if needed when host + mode or dual role mode is supported. + Particularly, if use an output GPIO to control a VBUS regulator, should + model it as a regulator. + see regulator/fixed-regulator.yaml +- pinctrl-names : a pinctrl state named "default" is optional +- pinctrl-0 : pin control group + see pinctrl/pinctrl-bindings.txt + Optional properties for usb-c-connector: - power-role: should be one of "source", "sink" or "dual"(DRP) if typec connector has power support. diff --git a/Documentation/devicetree/bindings/arm/topology.txt b/Documentation/devicetree/bindings/cpu/cpu-topology.txt index b0d80c0fb265..99918189403c 100644 --- a/Documentation/devicetree/bindings/arm/topology.txt +++ b/Documentation/devicetree/bindings/cpu/cpu-topology.txt @@ -1,21 +1,19 @@ =========================================== -ARM topology binding description +CPU topology binding description =========================================== =========================================== 1 - Introduction =========================================== -In an ARM system, the hierarchy of CPUs is defined through three entities that +In a SMP system, the hierarchy of CPUs is defined through three entities that are used to describe the layout of physical CPUs in the system: +- socket - cluster - core - thread -The cpu nodes (bindings defined in [1]) represent the devices that -correspond to physical CPUs and are to be mapped to the hierarchy levels. - The bottom hierarchy level sits at core or thread level depending on whether symmetric multi-threading (SMT) is supported or not. @@ -24,33 +22,31 @@ threads existing in the system and map to the hierarchy level "thread" above. In systems where SMT is not supported "cpu" nodes represent all cores present in the system and map to the hierarchy level "core" above. -ARM topology bindings allow one to associate cpu nodes with hierarchical groups +CPU topology bindings allow one to associate cpu nodes with hierarchical groups corresponding to the system hierarchy; syntactically they are defined as device tree nodes. -The remainder of this document provides the topology bindings for ARM, based -on the Devicetree Specification, available from: +Currently, only ARM/RISC-V intend to use this cpu topology binding but it may be +used for any other architecture as well. -https://www.devicetree.org/specifications/ +The cpu nodes, as per bindings defined in [4], represent the devices that +correspond to physical CPUs and are to be mapped to the hierarchy levels. -If not stated otherwise, whenever a reference to a cpu node phandle is made its -value must point to a cpu node compliant with the cpu node bindings as -documented in [1]. A topology description containing phandles to cpu nodes that are not compliant -with bindings standardized in [1] is therefore considered invalid. +with bindings standardized in [4] is therefore considered invalid. =========================================== 2 - cpu-map node =========================================== -The ARM CPU topology is defined within the cpu-map node, which is a direct +The ARM/RISC-V CPU topology is defined within the cpu-map node, which is a direct child of the cpus node and provides a container where the actual topology nodes are listed. - cpu-map node - Usage: Optional - On ARM SMP systems provide CPUs topology to the OS. - ARM uniprocessor systems do not require a topology + Usage: Optional - On SMP systems provide CPUs topology to the OS. + Uniprocessor systems do not require a topology description and therefore should not define a cpu-map node. @@ -63,21 +59,23 @@ nodes are listed. The cpu-map node's child nodes can be: - - one or more cluster nodes + - one or more cluster nodes or + - one or more socket nodes in a multi-socket system Any other configuration is considered invalid. -The cpu-map node can only contain three types of child nodes: +The cpu-map node can only contain 4 types of child nodes: +- socket node - cluster node - core node - thread node whose bindings are described in paragraph 3. -The nodes describing the CPU topology (cluster/core/thread) can only -be defined within the cpu-map node and every core/thread in the system -must be defined within the topology. Any other configuration is +The nodes describing the CPU topology (socket/cluster/core/thread) can +only be defined within the cpu-map node and every core/thread in the +system must be defined within the topology. Any other configuration is invalid and therefore must be ignored. =========================================== @@ -85,26 +83,44 @@ invalid and therefore must be ignored. =========================================== cpu-map child nodes must follow a naming convention where the node name -must be "clusterN", "coreN", "threadN" depending on the node type (ie -cluster/core/thread) (where N = {0, 1, ...} is the node number; nodes which -are siblings within a single common parent node must be given a unique and +must be "socketN", "clusterN", "coreN", "threadN" depending on the node type +(ie socket/cluster/core/thread) (where N = {0, 1, ...} is the node number; nodes +which are siblings within a single common parent node must be given a unique and sequential N value, starting from 0). cpu-map child nodes which do not share a common parent node can have the same name (ie same number N as other cpu-map child nodes at different device tree levels) since name uniqueness will be guaranteed by the device tree hierarchy. =========================================== -3 - cluster/core/thread node bindings +3 - socket/cluster/core/thread node bindings =========================================== -Bindings for cluster/cpu/thread nodes are defined as follows: +Bindings for socket/cluster/cpu/thread nodes are defined as follows: + +- socket node + + Description: must be declared within a cpu-map node, one node + per physical socket in the system. A system can + contain single or multiple physical socket. + The association of sockets and NUMA nodes is beyond + the scope of this bindings, please refer [2] for + NUMA bindings. + + This node is optional for a single socket system. + + The socket node name must be "socketN" as described in 2.1 above. + A socket node can not be a leaf node. + + A socket node's child nodes must be one or more cluster nodes. + + Any other configuration is considered invalid. - cluster node Description: must be declared within a cpu-map node, one node per cluster. A system can contain several layers of - clustering and cluster nodes can be contained in parent - cluster nodes. + clustering within a single physical socket and cluster + nodes can be contained in parent cluster nodes. The cluster node name must be "clusterN" as described in 2.1 above. A cluster node can not be a leaf node. @@ -164,90 +180,93 @@ Bindings for cluster/cpu/thread nodes are defined as follows: 4 - Example dts =========================================== -Example 1 (ARM 64-bit, 16-cpu system, two clusters of clusters): +Example 1 (ARM 64-bit, 16-cpu system, two clusters of clusters in a single +physical socket): cpus { #size-cells = <0>; #address-cells = <2>; cpu-map { - cluster0 { + socket0 { cluster0 { - core0 { - thread0 { - cpu = <&CPU0>; + cluster0 { + core0 { + thread0 { + cpu = <&CPU0>; + }; + thread1 { + cpu = <&CPU1>; + }; }; - thread1 { - cpu = <&CPU1>; - }; - }; - core1 { - thread0 { - cpu = <&CPU2>; - }; - thread1 { - cpu = <&CPU3>; + core1 { + thread0 { + cpu = <&CPU2>; + }; + thread1 { + cpu = <&CPU3>; + }; }; }; - }; - cluster1 { - core0 { - thread0 { - cpu = <&CPU4>; - }; - thread1 { - cpu = <&CPU5>; + cluster1 { + core0 { + thread0 { + cpu = <&CPU4>; + }; + thread1 { + cpu = <&CPU5>; + }; }; - }; - core1 { - thread0 { - cpu = <&CPU6>; - }; - thread1 { - cpu = <&CPU7>; - }; - }; - }; - }; - - cluster1 { - cluster0 { - core0 { - thread0 { - cpu = <&CPU8>; - }; - thread1 { - cpu = <&CPU9>; - }; - }; - core1 { - thread0 { - cpu = <&CPU10>; - }; - thread1 { - cpu = <&CPU11>; + core1 { + thread0 { + cpu = <&CPU6>; + }; + thread1 { + cpu = <&CPU7>; + }; }; }; }; cluster1 { - core0 { - thread0 { - cpu = <&CPU12>; + cluster0 { + core0 { + thread0 { + cpu = <&CPU8>; + }; + thread1 { + cpu = <&CPU9>; + }; }; - thread1 { - cpu = <&CPU13>; + core1 { + thread0 { + cpu = <&CPU10>; + }; + thread1 { + cpu = <&CPU11>; + }; }; }; - core1 { - thread0 { - cpu = <&CPU14>; + + cluster1 { + core0 { + thread0 { + cpu = <&CPU12>; + }; + thread1 { + cpu = <&CPU13>; + }; }; - thread1 { - cpu = <&CPU15>; + core1 { + thread0 { + cpu = <&CPU14>; + }; + thread1 { + cpu = <&CPU15>; + }; }; }; }; @@ -470,6 +489,65 @@ cpus { }; }; +Example 3: HiFive Unleashed (RISC-V 64 bit, 4 core system) + +{ + #address-cells = <2>; + #size-cells = <2>; + compatible = "sifive,fu540g", "sifive,fu500"; + model = "sifive,hifive-unleashed-a00"; + + ... + cpus { + #address-cells = <1>; + #size-cells = <0>; + cpu-map { + socket0 { + cluster0 { + core0 { + cpu = <&CPU1>; + }; + core1 { + cpu = <&CPU2>; + }; + core2 { + cpu0 = <&CPU2>; + }; + core3 { + cpu0 = <&CPU3>; + }; + }; + }; + }; + + CPU1: cpu@1 { + device_type = "cpu"; + compatible = "sifive,rocket0", "riscv"; + reg = <0x1>; + } + + CPU2: cpu@2 { + device_type = "cpu"; + compatible = "sifive,rocket0", "riscv"; + reg = <0x2>; + } + CPU3: cpu@3 { + device_type = "cpu"; + compatible = "sifive,rocket0", "riscv"; + reg = <0x3>; + } + CPU4: cpu@4 { + device_type = "cpu"; + compatible = "sifive,rocket0", "riscv"; + reg = <0x4>; + } + } +}; =============================================================================== [1] ARM Linux kernel documentation Documentation/devicetree/bindings/arm/cpus.yaml +[2] Devicetree NUMA binding description + Documentation/devicetree/bindings/numa.txt +[3] RISC-V Linux kernel documentation + Documentation/devicetree/bindings/riscv/cpus.txt +[4] https://www.devicetree.org/specifications/ diff --git a/Documentation/devicetree/bindings/cpufreq/imx-cpufreq-dt.txt b/Documentation/devicetree/bindings/cpufreq/imx-cpufreq-dt.txt new file mode 100644 index 000000000000..87bff5add3f9 --- /dev/null +++ b/Documentation/devicetree/bindings/cpufreq/imx-cpufreq-dt.txt @@ -0,0 +1,37 @@ +i.MX CPUFreq-DT OPP bindings +================================ + +Certain i.MX SoCs support different OPPs depending on the "market segment" and +"speed grading" value which are written in fuses. These bits are combined with +the opp-supported-hw values for each OPP to check if the OPP is allowed. + +Required properties: +-------------------- + +For each opp entry in 'operating-points-v2' table: +- opp-supported-hw: Two bitmaps indicating: + - Supported speed grade mask + - Supported market segment mask + 0: Consumer + 1: Extended Consumer + 2: Industrial + 3: Automotive + +Example: +-------- + +opp_table { + compatible = "operating-points-v2"; + opp-1000000000 { + opp-hz = /bits/ 64 <1000000000>; + /* grade >= 0, consumer only */ + opp-supported-hw = <0xf>, <0x3>; + }; + + opp-1300000000 { + opp-hz = /bits/ 64 <1300000000>; + opp-microvolt = <1000000>; + /* grade >= 1, all segments */ + opp-supported-hw = <0xe>, <0x7>; + }; +} diff --git a/Documentation/devicetree/bindings/crypto/allwinner,sun4i-a10-crypto.yaml b/Documentation/devicetree/bindings/crypto/allwinner,sun4i-a10-crypto.yaml new file mode 100644 index 000000000000..80b3e7350a73 --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/allwinner,sun4i-a10-crypto.yaml @@ -0,0 +1,79 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/crypto/allwinner,sun4i-a10-crypto.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 Security System Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + compatible: + oneOf: + - const: allwinner,sun4i-a10-crypto + - items: + - const: allwinner,sun5i-a13-crypto + - const: allwinner,sun4i-a10-crypto + - items: + - const: allwinner,sun6i-a31-crypto + - const: allwinner,sun4i-a10-crypto + - items: + - const: allwinner,sun7i-a20-crypto + - const: allwinner,sun4i-a10-crypto + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Bus Clock + - description: Module Clock + + clock-names: + items: + - const: ahb + - const: mod + + resets: + maxItems: 1 + + reset-names: + const: ahb + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +if: + properties: + compatible: + contains: + const: allwinner,sun6i-a31-crypto + +then: + required: + - resets + - reset-names + +additionalProperties: false + +examples: + - | + crypto: crypto-engine@1c15000 { + compatible = "allwinner,sun4i-a10-crypto"; + reg = <0x01c15000 0x1000>; + interrupts = <86>; + clocks = <&ahb_gates 5>, <&ss_clk>; + clock-names = "ahb", "mod"; + }; + +... diff --git a/Documentation/devicetree/bindings/crypto/atmel-crypto.txt b/Documentation/devicetree/bindings/crypto/atmel-crypto.txt index 6b458bb2440d..f2aab3dc2b52 100644 --- a/Documentation/devicetree/bindings/crypto/atmel-crypto.txt +++ b/Documentation/devicetree/bindings/crypto/atmel-crypto.txt @@ -66,16 +66,3 @@ sha@f8034000 { dmas = <&dma1 2 17>; dma-names = "tx"; }; - -* Eliptic Curve Cryptography (I2C) - -Required properties: -- compatible : must be "atmel,atecc508a". -- reg: I2C bus address of the device. -- clock-frequency: must be present in the i2c controller node. - -Example: -atecc508a@c0 { - compatible = "atmel,atecc508a"; - reg = <0xC0>; -}; diff --git a/Documentation/devicetree/bindings/crypto/sun4i-ss.txt b/Documentation/devicetree/bindings/crypto/sun4i-ss.txt deleted file mode 100644 index f2dc3d9bca92..000000000000 --- a/Documentation/devicetree/bindings/crypto/sun4i-ss.txt +++ /dev/null @@ -1,23 +0,0 @@ -* Allwinner Security System found on A20 SoC - -Required properties: -- compatible : Should be "allwinner,sun4i-a10-crypto". -- reg: Should contain the Security System register location and length. -- interrupts: Should contain the IRQ line for the Security System. -- clocks : List of clock specifiers, corresponding to ahb and ss. -- clock-names : Name of the functional clock, should be - * "ahb" : AHB gating clock - * "mod" : SS controller clock - -Optional properties: - - resets : phandle + reset specifier pair - - reset-names : must contain "ahb" - -Example: - crypto: crypto-engine@1c15000 { - compatible = "allwinner,sun4i-a10-crypto"; - reg = <0x01c15000 0x1000>; - interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ahb_gates 5>, <&ss_clk>; - clock-names = "ahb", "mod"; - }; diff --git a/Documentation/devicetree/bindings/csky/pmu.txt b/Documentation/devicetree/bindings/csky/pmu.txt new file mode 100644 index 000000000000..728d05ca6a1c --- /dev/null +++ b/Documentation/devicetree/bindings/csky/pmu.txt @@ -0,0 +1,38 @@ +=============================== +C-SKY Performance Monitor Units +=============================== + +C-SKY Performance Monitor is designed for ck807/ck810/ck860 SMP soc and +it could count cpu's events for helping analysis performance issues. + +============================ +PMU node bindings definition +============================ + + Description: Describes PMU + + PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: must be "csky,csky-pmu" + - interrupts + Usage: required + Value type: <u32 IRQ_TYPE_XXX> + Definition: must be pmu irq num defined by soc + - count-width + Usage: optional + Value type: <u32> + Definition: the width of pmu counter + +Examples: +--------- +#include <dt-bindings/interrupt-controller/irq.h> + + pmu: performace-monitor { + compatible = "csky,csky-pmu"; + interrupts = <23 IRQ_TYPE_EDGE_RISING>; + interrupt-parent = <&intc>; + count-width = <48>; + }; diff --git a/Documentation/devicetree/bindings/display/allwinner,sun6i-a31-mipi-dsi.yaml b/Documentation/devicetree/bindings/display/allwinner,sun6i-a31-mipi-dsi.yaml new file mode 100644 index 000000000000..47950fced28d --- /dev/null +++ b/Documentation/devicetree/bindings/display/allwinner,sun6i-a31-mipi-dsi.yaml @@ -0,0 +1,100 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/allwinner,sun6i-a31-mipi-dsi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A31 MIPI-DSI Controller Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + "#address-cells": true + "#size-cells": true + + compatible: + const: allwinner,sun6i-a31-mipi-dsi + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Bus Clock + - description: Module Clock + + clock-names: + items: + - const: bus + - const: mod + + resets: + maxItems: 1 + + phys: + maxItems: 1 + + phy-names: + const: dphy + + port: + type: object + description: + A port node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. That + port should be the input endpoint, usually coming from the + associated TCON. + +patternProperties: + "^panel@[0-9]+$": true + +required: + - "#address-cells" + - "#size-cells" + - compatible + - reg + - interrupts + - clocks + - clock-names + - phys + - phy-names + - resets + - port + +additionalProperties: false + +examples: + - | + dsi0: dsi@1ca0000 { + compatible = "allwinner,sun6i-a31-mipi-dsi"; + reg = <0x01ca0000 0x1000>; + interrupts = <0 89 4>; + clocks = <&ccu 23>, <&ccu 96>; + clock-names = "bus", "mod"; + resets = <&ccu 4>; + phys = <&dphy0>; + phy-names = "dphy"; + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "bananapi,lhr050h41", "ilitek,ili9881c"; + reg = <0>; + power-gpios = <&pio 1 7 0>; /* PB07 */ + reset-gpios = <&r_pio 0 5 1>; /* PL05 */ + backlight = <&pwm_bl>; + }; + + port { + dsi0_in_tcon0: endpoint { + remote-endpoint = <&tcon0_out_dsi0>; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/amlogic,meson-dw-hdmi.txt b/Documentation/devicetree/bindings/display/amlogic,meson-dw-hdmi.txt deleted file mode 100644 index 3a50a7862cf3..000000000000 --- a/Documentation/devicetree/bindings/display/amlogic,meson-dw-hdmi.txt +++ /dev/null @@ -1,119 +0,0 @@ -Amlogic specific extensions to the Synopsys Designware HDMI Controller -====================================================================== - -The Amlogic Meson Synopsys Designware Integration is composed of : -- A Synopsys DesignWare HDMI Controller IP -- A TOP control block controlling the Clocks and PHY -- A custom HDMI PHY in order to convert video to TMDS signal - ___________________________________ -| HDMI TOP |<= HPD -|___________________________________| -| | | -| Synopsys HDMI | HDMI PHY |=> TMDS -| Controller |________________| -|___________________________________|<=> DDC - -The HDMI TOP block only supports HPD sensing. -The Synopsys HDMI Controller interrupt is routed through the -TOP Block interrupt. -Communication to the TOP Block and the Synopsys HDMI Controller is done -via a pair of dedicated addr+read/write registers. -The HDMI PHY is configured by registers in the HHI register block. - -Pixel data arrives in 4:4:4 format from the VENC block and the VPU HDMI mux -selects either the ENCI encoder for the 576i or 480i formats or the ENCP -encoder for all the other formats including interlaced HD formats. - -The VENC uses a DVI encoder on top of the ENCI or ENCP encoders to generate -DVI timings for the HDMI controller. - -Amlogic Meson GXBB, GXL and GXM SoCs families embeds the Synopsys DesignWare -HDMI TX IP version 2.01a with HDCP and I2C & S/PDIF -audio source interfaces. - -Required properties: -- compatible: value should be different for each SoC family as : - - GXBB (S905) : "amlogic,meson-gxbb-dw-hdmi" - - GXL (S905X, S905D) : "amlogic,meson-gxl-dw-hdmi" - - GXM (S912) : "amlogic,meson-gxm-dw-hdmi" - followed by the common "amlogic,meson-gx-dw-hdmi" - - G12A (S905X2, S905Y2, S905D2) : "amlogic,meson-g12a-dw-hdmi" -- reg: Physical base address and length of the controller's registers. -- interrupts: The HDMI interrupt number -- clocks, clock-names : must have the phandles to the HDMI iahb and isfr clocks, - and the Amlogic Meson venci clocks as described in - Documentation/devicetree/bindings/clock/clock-bindings.txt, - the clocks are soc specific, the clock-names should be "iahb", "isfr", "venci" -- resets, resets-names: must have the phandles to the HDMI apb, glue and phy - resets as described in : - Documentation/devicetree/bindings/reset/reset.txt, - the reset-names should be "hdmitx_apb", "hdmitx", "hdmitx_phy" - -Optional properties: -- hdmi-supply: Optional phandle to an external 5V regulator to power the HDMI - logic, as described in the file ../regulator/regulator.txt - -Required nodes: - -The connections to the HDMI ports are modeled using the OF graph -bindings specified in Documentation/devicetree/bindings/graph.txt. - -The following table lists for each supported model the port number -corresponding to each HDMI output and input. - - Port 0 Port 1 ------------------------------------------ - S905 (GXBB) VENC Input TMDS Output - S905X (GXL) VENC Input TMDS Output - S905D (GXL) VENC Input TMDS Output - S912 (GXM) VENC Input TMDS Output - S905X2 (G12A) VENC Input TMDS Output - S905Y2 (G12A) VENC Input TMDS Output - S905D2 (G12A) VENC Input TMDS Output - -Example: - -hdmi-connector { - compatible = "hdmi-connector"; - type = "a"; - - port { - hdmi_connector_in: endpoint { - remote-endpoint = <&hdmi_tx_tmds_out>; - }; - }; -}; - -hdmi_tx: hdmi-tx@c883a000 { - compatible = "amlogic,meson-gxbb-dw-hdmi", "amlogic,meson-gx-dw-hdmi"; - reg = <0x0 0xc883a000 0x0 0x1c>; - interrupts = <GIC_SPI 57 IRQ_TYPE_EDGE_RISING>; - resets = <&reset RESET_HDMITX_CAPB3>, - <&reset RESET_HDMI_SYSTEM_RESET>, - <&reset RESET_HDMI_TX>; - reset-names = "hdmitx_apb", "hdmitx", "hdmitx_phy"; - clocks = <&clkc CLKID_HDMI_PCLK>, - <&clkc CLKID_CLK81>, - <&clkc CLKID_GCLK_VENCI_INT0>; - clock-names = "isfr", "iahb", "venci"; - #address-cells = <1>; - #size-cells = <0>; - - /* VPU VENC Input */ - hdmi_tx_venc_port: port@0 { - reg = <0>; - - hdmi_tx_in: endpoint { - remote-endpoint = <&hdmi_tx_out>; - }; - }; - - /* TMDS Output */ - hdmi_tx_tmds_port: port@1 { - reg = <1>; - - hdmi_tx_tmds_out: endpoint { - remote-endpoint = <&hdmi_connector_in>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/display/amlogic,meson-dw-hdmi.yaml b/Documentation/devicetree/bindings/display/amlogic,meson-dw-hdmi.yaml new file mode 100644 index 000000000000..fb747682006d --- /dev/null +++ b/Documentation/devicetree/bindings/display/amlogic,meson-dw-hdmi.yaml @@ -0,0 +1,150 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 BayLibre, SAS +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/display/amlogic,meson-dw-hdmi.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Amlogic specific extensions to the Synopsys Designware HDMI Controller + +maintainers: + - Neil Armstrong <narmstrong@baylibre.com> + +description: | + The Amlogic Meson Synopsys Designware Integration is composed of + - A Synopsys DesignWare HDMI Controller IP + - A TOP control block controlling the Clocks and PHY + - A custom HDMI PHY in order to convert video to TMDS signal + ___________________________________ + | HDMI TOP |<= HPD + |___________________________________| + | | | + | Synopsys HDMI | HDMI PHY |=> TMDS + | Controller |________________| + |___________________________________|<=> DDC + + The HDMI TOP block only supports HPD sensing. + The Synopsys HDMI Controller interrupt is routed through the + TOP Block interrupt. + Communication to the TOP Block and the Synopsys HDMI Controller is done + via a pair of dedicated addr+read/write registers. + The HDMI PHY is configured by registers in the HHI register block. + + Pixel data arrives in "4:4:4" format from the VENC block and the VPU HDMI mux + selects either the ENCI encoder for the 576i or 480i formats or the ENCP + encoder for all the other formats including interlaced HD formats. + + The VENC uses a DVI encoder on top of the ENCI or ENCP encoders to generate + DVI timings for the HDMI controller. + + Amlogic Meson GXBB, GXL and GXM SoCs families embeds the Synopsys DesignWare + HDMI TX IP version 2.01a with HDCP and I2C & S/PDIF + audio source interfaces. + +properties: + compatible: + oneOf: + - items: + - enum: + - amlogic,meson-gxbb-dw-hdmi # GXBB (S905) + - amlogic,meson-gxl-dw-hdmi # GXL (S905X, S905D) + - amlogic,meson-gxm-dw-hdmi # GXM (S912) + - const: amlogic,meson-gx-dw-hdmi + - enum: + - amlogic,meson-g12a-dw-hdmi # G12A (S905X2, S905Y2, S905D2) + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 3 + + clock-names: + items: + - const: isfr + - const: iahb + - const: venci + + resets: + minItems: 3 + + reset-names: + items: + - const: hdmitx_apb + - const: hdmitx + - const: hdmitx_phy + + hdmi-supply: + description: phandle to an external 5V regulator to power the HDMI logic + allOf: + - $ref: /schemas/types.yaml#/definitions/phandle + + port@0: + type: object + description: + A port node pointing to the VENC Input port node. + + port@1: + type: object + description: + A port node pointing to the TMDS Output port node. + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + "#sound-dai-cells": + const: 0 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - resets + - reset-names + - port@0 + - port@1 + - "#address-cells" + - "#size-cells" + +additionalProperties: false + +examples: + - | + hdmi_tx: hdmi-tx@c883a000 { + compatible = "amlogic,meson-gxbb-dw-hdmi", "amlogic,meson-gx-dw-hdmi"; + reg = <0xc883a000 0x1c>; + interrupts = <57>; + resets = <&reset_apb>, <&reset_hdmitx>, <&reset_hdmitx_phy>; + reset-names = "hdmitx_apb", "hdmitx", "hdmitx_phy"; + clocks = <&clk_isfr>, <&clk_iahb>, <&clk_venci>; + clock-names = "isfr", "iahb", "venci"; + #address-cells = <1>; + #size-cells = <0>; + + /* VPU VENC Input */ + hdmi_tx_venc_port: port@0 { + reg = <0>; + + hdmi_tx_in: endpoint { + remote-endpoint = <&hdmi_tx_out>; + }; + }; + + /* TMDS Output */ + hdmi_tx_tmds_port: port@1 { + reg = <1>; + + hdmi_tx_tmds_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/display/amlogic,meson-vpu.txt b/Documentation/devicetree/bindings/display/amlogic,meson-vpu.txt deleted file mode 100644 index be40a780501c..000000000000 --- a/Documentation/devicetree/bindings/display/amlogic,meson-vpu.txt +++ /dev/null @@ -1,121 +0,0 @@ -Amlogic Meson Display Controller -================================ - -The Amlogic Meson Display controller is composed of several components -that are going to be documented below: - -DMC|---------------VPU (Video Processing Unit)----------------|------HHI------| - | vd1 _______ _____________ _________________ | | -D |-------| |----| | | | | HDMI PLL | -D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK | -R |-------| |----| Processing | | | | | - | osd2 | | | |---| Enci ----------|----|-----VDAC------| -R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----| -A | osd1 | | | Blenders | | Encl ----------|----|---------------| -M |-------|______|----|____________| |________________| | | -___|__________________________________________________________|_______________| - - -VIU: Video Input Unit ---------------------- - -The Video Input Unit is in charge of the pixel scanout from the DDR memory. -It fetches the frames addresses, stride and parameters from the "Canvas" memory. -This part is also in charge of the CSC (Colorspace Conversion). -It can handle 2 OSD Planes and 2 Video Planes. - -VPP: Video Post Processing --------------------------- - -The Video Post Processing is in charge of the scaling and blending of the -various planes into a single pixel stream. -There is a special "pre-blending" used by the video planes with a dedicated -scaler and a "post-blending" to merge with the OSD Planes. -The OSD planes also have a dedicated scaler for one of the OSD. - -VENC: Video Encoders --------------------- - -The VENC is composed of the multiple pixel encoders : - - ENCI : Interlace Video encoder for CVBS and Interlace HDMI - - ENCP : Progressive Video Encoder for HDMI - - ENCL : LCD LVDS Encoder -The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock -tree and provides the scanout clock to the VPP and VIU. -The ENCI is connected to a single VDAC for Composite Output. -The ENCI and ENCP are connected to an on-chip HDMI Transceiver. - -Device Tree Bindings: ---------------------- - -VPU: Video Processing Unit --------------------------- - -Required properties: -- compatible: value should be different for each SoC family as : - - GXBB (S905) : "amlogic,meson-gxbb-vpu" - - GXL (S905X, S905D) : "amlogic,meson-gxl-vpu" - - GXM (S912) : "amlogic,meson-gxm-vpu" - followed by the common "amlogic,meson-gx-vpu" - - G12A (S905X2, S905Y2, S905D2) : "amlogic,meson-g12a-vpu" -- reg: base address and size of he following memory-mapped regions : - - vpu - - hhi -- reg-names: should contain the names of the previous memory regions -- interrupts: should contain the VENC Vsync interrupt number -- amlogic,canvas: phandle to canvas provider node as described in the file - ../soc/amlogic/amlogic,canvas.txt - -Optional properties: -- power-domains: Optional phandle to associated power domain as described in - the file ../power/power_domain.txt - -Required nodes: - -The connections to the VPU output video ports are modeled using the OF graph -bindings specified in Documentation/devicetree/bindings/graph.txt. - -The following table lists for each supported model the port number -corresponding to each VPU output. - - Port 0 Port 1 ------------------------------------------ - S905 (GXBB) CVBS VDAC HDMI-TX - S905X (GXL) CVBS VDAC HDMI-TX - S905D (GXL) CVBS VDAC HDMI-TX - S912 (GXM) CVBS VDAC HDMI-TX - S905X2 (G12A) CVBS VDAC HDMI-TX - S905Y2 (G12A) CVBS VDAC HDMI-TX - S905D2 (G12A) CVBS VDAC HDMI-TX - -Example: - -tv-connector { - compatible = "composite-video-connector"; - - port { - tv_connector_in: endpoint { - remote-endpoint = <&cvbs_vdac_out>; - }; - }; -}; - -vpu: vpu@d0100000 { - compatible = "amlogic,meson-gxbb-vpu"; - reg = <0x0 0xd0100000 0x0 0x100000>, - <0x0 0xc883c000 0x0 0x1000>, - <0x0 0xc8838000 0x0 0x1000>; - reg-names = "vpu", "hhi", "dmc"; - interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>; - #address-cells = <1>; - #size-cells = <0>; - - /* CVBS VDAC output port */ - port@0 { - reg = <0>; - - cvbs_vdac_out: endpoint { - remote-endpoint = <&tv_connector_in>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/display/amlogic,meson-vpu.yaml b/Documentation/devicetree/bindings/display/amlogic,meson-vpu.yaml new file mode 100644 index 000000000000..d1205a6697a0 --- /dev/null +++ b/Documentation/devicetree/bindings/display/amlogic,meson-vpu.yaml @@ -0,0 +1,137 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 BayLibre, SAS +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/display/amlogic,meson-vpu.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Amlogic Meson Display Controller + +maintainers: + - Neil Armstrong <narmstrong@baylibre.com> + +description: | + The Amlogic Meson Display controller is composed of several components + that are going to be documented below + + DMC|---------------VPU (Video Processing Unit)----------------|------HHI------| + | vd1 _______ _____________ _________________ | | + D |-------| |----| | | | | HDMI PLL | + D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK | + R |-------| |----| Processing | | | | | + | osd2 | | | |---| Enci ----------|----|-----VDAC------| + R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----| + A | osd1 | | | Blenders | | Encl ----------|----|---------------| + M |-------|______|----|____________| |________________| | | + ___|__________________________________________________________|_______________| + + + VIU: Video Input Unit + --------------------- + + The Video Input Unit is in charge of the pixel scanout from the DDR memory. + It fetches the frames addresses, stride and parameters from the "Canvas" memory. + This part is also in charge of the CSC (Colorspace Conversion). + It can handle 2 OSD Planes and 2 Video Planes. + + VPP: Video Post Processing + -------------------------- + + The Video Post Processing is in charge of the scaling and blending of the + various planes into a single pixel stream. + There is a special "pre-blending" used by the video planes with a dedicated + scaler and a "post-blending" to merge with the OSD Planes. + The OSD planes also have a dedicated scaler for one of the OSD. + + VENC: Video Encoders + -------------------- + + The VENC is composed of the multiple pixel encoders + - ENCI : Interlace Video encoder for CVBS and Interlace HDMI + - ENCP : Progressive Video Encoder for HDMI + - ENCL : LCD LVDS Encoder + The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock + tree and provides the scanout clock to the VPP and VIU. + The ENCI is connected to a single VDAC for Composite Output. + The ENCI and ENCP are connected to an on-chip HDMI Transceiver. + +properties: + compatible: + oneOf: + - items: + - enum: + - amlogic,meson-gxbb-vpu # GXBB (S905) + - amlogic,meson-gxl-vpu # GXL (S905X, S905D) + - amlogic,meson-gxm-vpu # GXM (S912) + - const: amlogic,meson-gx-vpu + - enum: + - amlogic,meson-g12a-vpu # G12A (S905X2, S905Y2, S905D2) + + reg: + maxItems: 2 + + reg-names: + items: + - const: vpu + - const: hhi + + interrupts: + maxItems: 1 + + power-domains: + maxItems: 1 + description: phandle to the associated power domain + + port@0: + type: object + description: + A port node pointing to the CVBS VDAC port node. + + port@1: + type: object + description: + A port node pointing to the HDMI-TX port node. + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + +required: + - compatible + - reg + - interrupts + - port@0 + - port@1 + - "#address-cells" + - "#size-cells" + +examples: + - | + vpu: vpu@d0100000 { + compatible = "amlogic,meson-gxbb-vpu", "amlogic,meson-gx-vpu"; + reg = <0xd0100000 0x100000>, <0xc883c000 0x1000>; + reg-names = "vpu", "hhi"; + interrupts = <3>; + #address-cells = <1>; + #size-cells = <0>; + + /* CVBS VDAC output port */ + port@0 { + reg = <0>; + + cvbs_vdac_out: endpoint { + remote-endpoint = <&tv_connector_in>; + }; + }; + + /* HDMI TX output port */ + port@1 { + reg = <1>; + + hdmi_tx_out: endpoint { + remote-endpoint = <&hdmi_tx_in>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/arm,komeda.txt b/Documentation/devicetree/bindings/display/arm,komeda.txt index 02b226532ebd..8513695ee47f 100644 --- a/Documentation/devicetree/bindings/display/arm,komeda.txt +++ b/Documentation/devicetree/bindings/display/arm,komeda.txt @@ -7,10 +7,13 @@ Required properties: - clocks: A list of phandle + clock-specifier pairs, one for each entry in 'clock-names' - clock-names: A list of clock names. It should contain: - - "mclk": for the main processor clock - - "pclk": for the APB interface clock + - "aclk": for the main processor clock - #address-cells: Must be 1 - #size-cells: Must be 0 +- iommus: configure the stream id to IOMMU, Must be configured if want to + enable iommu in display. for how to configure this node please reference + devicetree/bindings/iommu/arm,smmu-v3.txt, + devicetree/bindings/iommu/iommu.txt Required properties for sub-node: pipeline@nq Each device contains one or two pipeline sub-nodes (at least one), each @@ -20,7 +23,6 @@ pipeline node should provide properties: in 'clock-names' - clock-names: should contain: - "pxclk": pixel clock - - "aclk": AXI interface clock - port: each pipeline connect to an encoder input port. The connection is modeled using the OF graph bindings specified in @@ -42,12 +44,15 @@ Example: compatible = "arm,mali-d71"; reg = <0xc00000 0x20000>; interrupts = <0 168 4>; - clocks = <&dpu_mclk>, <&dpu_aclk>; - clock-names = "mclk", "pclk"; + clocks = <&dpu_aclk>; + clock-names = "aclk"; + iommus = <&smmu 0>, <&smmu 1>, <&smmu 2>, <&smmu 3>, + <&smmu 4>, <&smmu 5>, <&smmu 6>, <&smmu 7>, + <&smmu 8>, <&smmu 9>; dp0_pipe0: pipeline@0 { - clocks = <&fpgaosc2>, <&dpu_aclk>; - clock-names = "pxclk", "aclk"; + clocks = <&fpgaosc2>; + clock-names = "pxclk"; reg = <0>; port { @@ -58,8 +63,8 @@ Example: }; dp0_pipe1: pipeline@1 { - clocks = <&fpgaosc2>, <&dpu_aclk>; - clock-names = "pxclk", "aclk"; + clocks = <&fpgaosc2>; + clock-names = "pxclk"; reg = <1>; port { diff --git a/Documentation/devicetree/bindings/display/arm,pl11x.txt b/Documentation/devicetree/bindings/display/arm,pl11x.txt index 572fa2773ec4..3f977e72a200 100644 --- a/Documentation/devicetree/bindings/display/arm,pl11x.txt +++ b/Documentation/devicetree/bindings/display/arm,pl11x.txt @@ -39,9 +39,11 @@ Required sub-nodes: - port: describes LCD panel signals, following the common binding for video transmitter interfaces; see - Documentation/devicetree/bindings/media/video-interfaces.txt; - when it is a TFT panel, the port's endpoint must define the - following property: + Documentation/devicetree/bindings/media/video-interfaces.txt + +Deprecated properties: + The port's endbpoint subnode had this, now deprecated property + in the past. Drivers should be able to survive without it: - arm,pl11x,tft-r0g0b0-pads: an array of three 32-bit values, defining the way CLD pads are wired up; first value @@ -80,7 +82,6 @@ Example: port { clcd_pads: endpoint { remote-endpoint = <&clcd_panel>; - arm,pl11x,tft-r0g0b0-pads = <0 8 16>; }; }; diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt index a41d280c3f9f..db680413e89c 100644 --- a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt +++ b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt @@ -12,10 +12,12 @@ following device-specific properties. Required properties: - compatible : Shall contain one or more of + - "renesas,r8a774a1-hdmi" for R8A774A1 (RZ/G2M) compatible HDMI TX - "renesas,r8a7795-hdmi" for R8A7795 (R-Car H3) compatible HDMI TX - "renesas,r8a7796-hdmi" for R8A7796 (R-Car M3-W) compatible HDMI TX - "renesas,r8a77965-hdmi" for R8A77965 (R-Car M3-N) compatible HDMI TX - - "renesas,rcar-gen3-hdmi" for the generic R-Car Gen3 compatible HDMI TX + - "renesas,rcar-gen3-hdmi" for the generic R-Car Gen3 and RZ/G2 compatible + HDMI TX When compatible with generic versions, nodes must list the SoC-specific version corresponding to the platform first, followed by the diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt b/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt index 900a884ad9f5..c6a196d0b075 100644 --- a/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt +++ b/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt @@ -9,6 +9,7 @@ Required properties: - compatible : Shall contain one of - "renesas,r8a7743-lvds" for R8A7743 (RZ/G1M) compatible LVDS encoders - "renesas,r8a7744-lvds" for R8A7744 (RZ/G1N) compatible LVDS encoders + - "renesas,r8a774a1-lvds" for R8A774A1 (RZ/G2M) compatible LVDS encoders - "renesas,r8a774c0-lvds" for R8A774C0 (RZ/G2E) compatible LVDS encoders - "renesas,r8a7790-lvds" for R8A7790 (R-Car H2) compatible LVDS encoders - "renesas,r8a7791-lvds" for R8A7791 (R-Car M2-W) compatible LVDS encoders @@ -45,14 +46,24 @@ OF graph bindings specified in Documentation/devicetree/bindings/graph.txt. Each port shall have a single endpoint. +Optional properties: + +- renesas,companion : phandle to the companion LVDS encoder. This property is + mandatory for the first LVDS encoder on D3 and E3 SoCs, and shall point to + the second encoder to be used as a companion in dual-link mode. It shall not + be set for any other LVDS encoder. + Example: lvds0: lvds@feb90000 { - compatible = "renesas,r8a7790-lvds"; - reg = <0 0xfeb90000 0 0x1c>; - clocks = <&cpg CPG_MOD 726>; - resets = <&cpg 726>; + compatible = "renesas,r8a77990-lvds"; + reg = <0 0xfeb90000 0 0x20>; + clocks = <&cpg CPG_MOD 727>; + power-domains = <&sysc R8A77990_PD_ALWAYS_ON>; + resets = <&cpg 727>; + + renesas,companion = <&lvds1>; ports { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/display/bridge/sii902x.txt b/Documentation/devicetree/bindings/display/bridge/sii902x.txt index 72d2dc6c3e6b..6e14e087c0d0 100644 --- a/Documentation/devicetree/bindings/display/bridge/sii902x.txt +++ b/Documentation/devicetree/bindings/display/bridge/sii902x.txt @@ -5,10 +5,43 @@ Required properties: - reg: i2c address of the bridge Optional properties: - - interrupts: describe the interrupt line used to inform the host + - interrupts: describe the interrupt line used to inform the host about hotplug events. - reset-gpios: OF device-tree gpio specification for RST_N pin. + HDMI audio properties: + - #sound-dai-cells: <0> or <1>. <0> if only i2s or spdif pin + is wired, <1> if the both are wired. HDMI audio is + configured only if this property is found. + - sil,i2s-data-lanes: Array of up to 4 integers with values of 0-3 + Each integer indicates which i2s pin is connected to which + audio fifo. The first integer selects i2s audio pin for the + first audio fifo#0 (HDMI channels 1&2), second for fifo#1 + (HDMI channels 3&4), and so on. There is 4 fifos and 4 i2s + pins (SD0 - SD3). Any i2s pin can be connected to any fifo, + but there can be no gaps. E.g. an i2s pin must be mapped to + fifo#0 and fifo#1 before mapping a channel to fifo#2. Default + value is <0>, describing SD0 pin beiging routed to hdmi audio + fifo #0. + - clocks: phandle and clock specifier for each clock listed in + the clock-names property + - clock-names: "mclk" + Describes SII902x MCLK input. MCLK can be used to produce + HDMI audio CTS values. This property follows + Documentation/devicetree/bindings/clock/clock-bindings.txt + consumer binding. + + If HDMI audio is configured the sii902x device becomes an I2S + and/or spdif audio codec component (e.g a digital audio sink), + that can be used in configuring a full audio devices with + simple-card or audio-graph-card binding. See their binding + documents on how to describe the way the sii902x device is + connected to the rest of the audio system: + Documentation/devicetree/bindings/sound/simple-card.txt + Documentation/devicetree/bindings/sound/audio-graph-card.txt + Note: In case of the audio-graph-card binding the used port + index should be 3. + Optional subnodes: - video input: this subnode can contain a video input port node to connect the bridge to a display controller output (See this @@ -21,6 +54,12 @@ Example: compatible = "sil,sii9022"; reg = <0x39>; reset-gpios = <&pioA 1 0>; + + #sound-dai-cells = <0>; + sil,i2s-data-lanes = < 0 1 2 >; + clocks = <&mclk>; + clock-names = "mclk"; + ports { #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt index 37f0c04d5a28..d17d1e5820d7 100644 --- a/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt +++ b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt @@ -28,6 +28,12 @@ Optional video port nodes: - port@1: Second LVDS input port - port@3: Second digital CMOS/TTL parallel output +The device can operate in single-link mode or dual-link mode. In single-link +mode, all pixels are received on port@0, and port@1 shall not contain any +endpoint. In dual-link mode, even-numbered pixels are received on port@0 and +odd-numbered pixels on port@1, and both port@0 and port@1 shall contain +endpoints. + Example: -------- diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358767.txt b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358767.txt index e3f6aa6a214d..583c5e9dbe6b 100644 --- a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358767.txt +++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358767.txt @@ -12,6 +12,7 @@ Optional properties: (active high shutdown input) - reset-gpios: OF device-tree gpio specification for RSTX pin (active low system reset) + - toshiba,hpd-pin: TC358767 GPIO pin number to which HPD is connected to (0 or 1) - ports: the ports node can contain video interface port nodes to connect to a DPI/DSI source and to an eDP/DP sink according to [1][2]: - port@0: DSI input port diff --git a/Documentation/devicetree/bindings/display/connector/hdmi-connector.txt b/Documentation/devicetree/bindings/display/connector/hdmi-connector.txt index 508aee461e0d..aeb07c4bd703 100644 --- a/Documentation/devicetree/bindings/display/connector/hdmi-connector.txt +++ b/Documentation/devicetree/bindings/display/connector/hdmi-connector.txt @@ -9,6 +9,7 @@ Optional properties: - label: a symbolic name for the connector - hpd-gpios: HPD GPIO number - ddc-i2c-bus: phandle link to the I2C controller used for DDC EDID probing +- ddc-en-gpios: signal to enable DDC bus Required nodes: - Video port for HDMI input diff --git a/Documentation/devicetree/bindings/display/ingenic,lcd.txt b/Documentation/devicetree/bindings/display/ingenic,lcd.txt new file mode 100644 index 000000000000..7b536c8c6dde --- /dev/null +++ b/Documentation/devicetree/bindings/display/ingenic,lcd.txt @@ -0,0 +1,44 @@ +Ingenic JZ47xx LCD driver + +Required properties: +- compatible: one of: + * ingenic,jz4740-lcd + * ingenic,jz4725b-lcd +- reg: LCD registers location and length +- clocks: LCD pixclock and device clock specifiers. + The device clock is only required on the JZ4740. +- clock-names: "lcd_pclk" and "lcd" +- interrupts: Specifies the interrupt line the LCD controller is connected to. + +Example: + +panel { + compatible = "sharp,ls020b1dd01d"; + + backlight = <&backlight>; + power-supply = <&vcc>; + + port { + panel_input: endpoint { + remote-endpoint = <&panel_output>; + }; + }; +}; + + +lcd: lcd-controller@13050000 { + compatible = "ingenic,jz4725b-lcd"; + reg = <0x13050000 0x1000>; + + interrupt-parent = <&intc>; + interrupts = <31>; + + clocks = <&cgu JZ4725B_CLK_LCD>; + clock-names = "lcd"; + + port { + panel_output: endpoint { + remote-endpoint = <&panel_input>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/msm/dpu.txt b/Documentation/devicetree/bindings/display/msm/dpu.txt index ad2e8830324e..a61dd40f3792 100644 --- a/Documentation/devicetree/bindings/display/msm/dpu.txt +++ b/Documentation/devicetree/bindings/display/msm/dpu.txt @@ -28,6 +28,11 @@ Required properties: - #address-cells: number of address cells for the MDSS children. Should be 1. - #size-cells: Should be 1. - ranges: parent bus address space is the same as the child bus address space. +- interconnects : interconnect path specifier for MDSS according to + Documentation/devicetree/bindings/interconnect/interconnect.txt. Should be + 2 paths corresponding to 2 AXI ports. +- interconnect-names : MDSS will have 2 port names to differentiate between the + 2 interconnect paths defined with interconnect specifier. Optional properties: - assigned-clocks: list of clock specifiers for clocks needing rate assignment @@ -86,6 +91,11 @@ Example: interrupt-controller; #interrupt-cells = <1>; + interconnects = <&rsc_hlos MASTER_MDP0 &rsc_hlos SLAVE_EBI1>, + <&rsc_hlos MASTER_MDP1 &rsc_hlos SLAVE_EBI1>; + + interconnect-names = "mdp0-mem", "mdp1-mem"; + iommus = <&apps_iommu 0>; #address-cells = <2>; diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt b/Documentation/devicetree/bindings/display/msm/dsi.txt index 9ae946942720..af95586c898f 100644 --- a/Documentation/devicetree/bindings/display/msm/dsi.txt +++ b/Documentation/devicetree/bindings/display/msm/dsi.txt @@ -88,6 +88,7 @@ Required properties: * "qcom,dsi-phy-28nm-8960" * "qcom,dsi-phy-14nm" * "qcom,dsi-phy-10nm" + * "qcom,dsi-phy-10nm-8998" - reg: Physical base address and length of the registers of PLL, PHY. Some revisions require the PHY regulator base address, whereas others require the PHY lane base address. See below for each PHY revision. diff --git a/Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.txt b/Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.txt deleted file mode 100644 index 6812280cb109..000000000000 --- a/Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.txt +++ /dev/null @@ -1,26 +0,0 @@ -Ampire AM-480272H3TMQW-T01H 4.3" WQVGA TFT LCD panel - -This binding is compatible with the simple-panel binding, which is specified -in simple-panel.txt in this directory. - -Required properties: -- compatible: should be "ampire,am-480272h3tmqw-t01h" - -Optional properties: -- power-supply: regulator to provide the supply voltage -- enable-gpios: GPIO pin to enable or disable the panel -- backlight: phandle of the backlight device attached to the panel - -Optional nodes: -- Video port for RGB input. - -Example: - panel_rgb: panel-rgb { - compatible = "ampire,am-480272h3tmqw-t01h"; - enable-gpios = <&gpioa 8 1>; - port { - panel_in_rgb: endpoint { - remote-endpoint = <&controller_out_rgb>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.yaml b/Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.yaml new file mode 100644 index 000000000000..c6e33e7f36d0 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.yaml @@ -0,0 +1,42 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/ampire,am-480272h3tmqw-t01h.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ampire AM-480272H3TMQW-T01H 4.3" WQVGA TFT LCD panel + +maintainers: + - Yannick Fertre <yannick.fertre@st.com> + - Thierry Reding <treding@nvidia.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: ampire,am-480272h3tmqw-t01h + + power-supply: true + enable-gpios: true + backlight: true + port: true + +required: + - compatible + +additionalProperties: false + +examples: + - | + panel_rgb: panel { + compatible = "ampire,am-480272h3tmqw-t01h"; + enable-gpios = <&gpioa 8 1>; + port { + panel_in_rgb: endpoint { + remote-endpoint = <&controller_out_rgb>; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.txt b/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.txt index 248141c3c7e3..0601a9e34703 100644 --- a/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.txt +++ b/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.txt @@ -10,7 +10,7 @@ Required properties: - compatible: should be "arm,versatile-tft-panel" Required subnodes: -- port: see display/panel/panel-common.txt, graph.txt +- port: see display/panel/panel-common.yaml, graph.txt Example: diff --git a/Documentation/devicetree/bindings/display/panel/armadeus,st0700-adapt.yaml b/Documentation/devicetree/bindings/display/panel/armadeus,st0700-adapt.yaml new file mode 100644 index 000000000000..a6ade47066b3 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/armadeus,st0700-adapt.yaml @@ -0,0 +1,33 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/armadeus,st0700-adapt.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Armadeus ST0700 Adapter + +description: + A Santek ST0700I5Y-RBSLW 7.0" WVGA (800x480) TFT with an adapter board. + +maintainers: + - '"Sébastien Szymanski" <sebastien.szymanski@armadeus.com>' + - Thierry Reding <thierry.reding@gmail.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: armadeus,st0700-adapt + + power-supply: true + backlight: true + port: true + +additionalProperties: false + +required: + - compatible + - power-supply + +... diff --git a/Documentation/devicetree/bindings/display/panel/bananapi,s070wv20-ct16.txt b/Documentation/devicetree/bindings/display/panel/bananapi,s070wv20-ct16.txt deleted file mode 100644 index 35bc0c839f49..000000000000 --- a/Documentation/devicetree/bindings/display/panel/bananapi,s070wv20-ct16.txt +++ /dev/null @@ -1,12 +0,0 @@ -Banana Pi 7" (S070WV20-CT16) TFT LCD Panel - -Required properties: -- compatible: should be "bananapi,s070wv20-ct16" -- power-supply: see ./panel-common.txt - -Optional properties: -- enable-gpios: see ./simple-panel.txt -- backlight: see ./simple-panel.txt - -This binding is compatible with the simple-panel binding, which is specified -in ./simple-panel.txt. diff --git a/Documentation/devicetree/bindings/display/panel/bananapi,s070wv20-ct16.yaml b/Documentation/devicetree/bindings/display/panel/bananapi,s070wv20-ct16.yaml new file mode 100644 index 000000000000..bbf127fb28f7 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/bananapi,s070wv20-ct16.yaml @@ -0,0 +1,31 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/bananapi,s070wv20-ct16.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Banana Pi 7" (S070WV20-CT16) TFT LCD Panel + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Thierry Reding <thierry.reding@gmail.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: bananapi,s070wv20-ct16 + + power-supply: true + backlight: true + enable-gpios: true + port: true + +additionalProperties: false + +required: + - compatible + - power-supply + +... diff --git a/Documentation/devicetree/bindings/display/panel/boe,himax8279d.txt b/Documentation/devicetree/bindings/display/panel/boe,himax8279d.txt new file mode 100644 index 000000000000..3caea2172b1b --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/boe,himax8279d.txt @@ -0,0 +1,24 @@ +Boe Himax8279d 1200x1920 TFT LCD panel + +Required properties: +- compatible: should be "boe,himax8279d8p" and one of: "boe,himax8279d10p" +- reg: DSI virtual channel of the peripheral +- enable-gpios: panel enable gpio +- pp33-gpios: a GPIO phandle for the 3.3v pin that provides the supply voltage +- pp18-gpios: a GPIO phandle for the 1.8v pin that provides the supply voltage + +Optional properties: +- backlight: phandle of the backlight device attached to the panel + +Example: + + &mipi_dsi { + panel { + compatible = "boe,himax8279d8p", "boe,himax8279d10p"; + reg = <0>; + backlight = <&backlight>; + enable-gpios = <&gpio 45 GPIO_ACTIVE_HIGH>; + pp33-gpios = <&gpio 35 GPIO_ACTIVE_HIGH>; + pp18-gpios = <&gpio 36 GPIO_ACTIVE_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml b/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml new file mode 100644 index 000000000000..287e2feb6533 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml @@ -0,0 +1,31 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/dlc,dlc0700yzg-1.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: DLC Display Co. DLC0700YZG-1 7.0" WSVGA TFT LCD panel + +maintainers: + - Philipp Zabel <p.zabel@pengutronix.de> + - Thierry Reding <thierry.reding@gmail.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: dlc,dlc0700yzg-1 + + reset-gpios: true + enable-gpios: true + backlight: true + port: true + +additionalProperties: false + +required: + - compatible + - power-supply + +... diff --git a/Documentation/devicetree/bindings/display/panel/edt,et-series.txt b/Documentation/devicetree/bindings/display/panel/edt,et-series.txt index f56b99ebd9be..b7ac1c725f97 100644 --- a/Documentation/devicetree/bindings/display/panel/edt,et-series.txt +++ b/Documentation/devicetree/bindings/display/panel/edt,et-series.txt @@ -6,6 +6,22 @@ Display bindings for EDT Display Technology Corp. Displays which are compatible with the simple-panel binding, which is specified in simple-panel.txt +3,5" QVGA TFT Panels +-------------------- ++-----------------+---------------------+-------------------------------------+ +| Identifier | compatbile | description | ++=================+=====================+=====================================+ +| ET035012DM6 | edt,et035012dm6 | 3.5" QVGA TFT LCD panel | ++-----------------+---------------------+-------------------------------------+ + +4,3" WVGA TFT Panels +-------------------- + ++-----------------+---------------------+-------------------------------------+ +| Identifier | compatbile | description | ++=================+=====================+=====================================+ +| ETM0430G0DH6 | edt,etm0430g0dh6 | 480x272 TFT Display | ++-----------------+---------------------+-------------------------------------+ 5,7" WVGA TFT Panels -------------------- @@ -24,7 +40,7 @@ simple-panel.txt | Identifier | compatbile | description | +=================+=====================+=====================================+ | ETM0700G0DH6 | edt,etm070080dh6 | WVGA TFT Display with capacitive | -| | | Touchscreen | +| | edt,etm0700g0dh6 | Touchscreen | +-----------------+---------------------+-------------------------------------+ | ETM0700G0BDH6 | edt,etm070080bdh6 | Same as ETM0700G0DH6 but with | | | | inverted pixel clock. | diff --git a/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt b/Documentation/devicetree/bindings/display/panel/evervision,vgg804821.txt index bf06bb025b08..82d22e191ac3 100644 --- a/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt +++ b/Documentation/devicetree/bindings/display/panel/evervision,vgg804821.txt @@ -1,13 +1,12 @@ -DLC Display Co. DLC0700YZG-1 7.0" WSVGA TFT LCD panel +Evervision Electronics Co. Ltd. VGG804821 5.0" WVGA TFT LCD Panel Required properties: -- compatible: should be "dlc,dlc0700yzg-1" +- compatible: should be "evervision,vgg804821" - power-supply: See simple-panel.txt Optional properties: -- reset-gpios: See panel-common.txt -- enable-gpios: See simple-panel.txt - backlight: See simple-panel.txt +- enable-gpios: See simple-panel.txt This binding is compatible with the simple-panel binding, which is specified in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/friendlyarm,hd702e.txt b/Documentation/devicetree/bindings/display/panel/friendlyarm,hd702e.txt new file mode 100644 index 000000000000..6c9156fc3478 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/friendlyarm,hd702e.txt @@ -0,0 +1,32 @@ +FriendlyELEC HD702E 800x1280 LCD panel + +HD702E lcd is FriendlyELEC developed eDP LCD panel with 800x1280 +resolution. It has built in Goodix, GT9271 captive touchscreen +with backlight adjustable via PWM. + +Required properties: +- compatible: should be "friendlyarm,hd702e" +- power-supply: regulator to provide the supply voltage + +Optional properties: +- backlight: phandle of the backlight device attached to the panel + +Optional nodes: +- Video port for LCD panel input. + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. + +Example: + + panel { + compatible ="friendlyarm,hd702e", "simple-panel"; + backlight = <&backlight>; + power-supply = <&vcc3v3_sys>; + + port { + panel_in_edp: endpoint { + remote-endpoint = <&edp_out_panel>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/giantplus,gpm940b0.txt b/Documentation/devicetree/bindings/display/panel/giantplus,gpm940b0.txt new file mode 100644 index 000000000000..3dab52f92c26 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/giantplus,gpm940b0.txt @@ -0,0 +1,12 @@ +GiantPlus 3.0" (320x240 pixels) 24-bit TFT LCD panel + +Required properties: +- compatible: should be "giantplus,gpm940b0" +- power-supply: as specified in the base binding + +Optional properties: +- backlight: as specified in the base binding +- enable-gpios: as specified in the base binding + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/innolux,ee101ia-01d.txt b/Documentation/devicetree/bindings/display/panel/innolux,ee101ia-01d.txt deleted file mode 100644 index e5ca4ccd55ed..000000000000 --- a/Documentation/devicetree/bindings/display/panel/innolux,ee101ia-01d.txt +++ /dev/null @@ -1,7 +0,0 @@ -Innolux Corporation 10.1" EE101IA-01D WXGA (1280x800) LVDS panel - -Required properties: -- compatible: should be "innolux,ee101ia-01d" - -This binding is compatible with the lvds-panel binding, which is specified -in panel-lvds.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/innolux,ee101ia-01d.yaml b/Documentation/devicetree/bindings/display/panel/innolux,ee101ia-01d.yaml new file mode 100644 index 000000000000..a69681e724cb --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/innolux,ee101ia-01d.yaml @@ -0,0 +1,31 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/innolux,ee101ia-01d.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Innolux Corporation 10.1" EE101IA-01D WXGA (1280x800) LVDS panel + +maintainers: + - Heiko Stuebner <heiko.stuebner@bq.com> + - Thierry Reding <thierry.reding@gmail.com> + +allOf: + - $ref: lvds.yaml# + +properties: + compatible: + items: + - const: innolux,ee101ia-01d + - {} # panel-lvds, but not listed here to avoid false select + + backlight: true + enable-gpios: true + power-supply: true + width-mm: true + height-mm: true + panel-timing: true + port: true + +additionalProperties: false +... diff --git a/Documentation/devicetree/bindings/display/panel/kingdisplay,kd035g6-54nt.txt b/Documentation/devicetree/bindings/display/panel/kingdisplay,kd035g6-54nt.txt new file mode 100644 index 000000000000..fa9596082e44 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/kingdisplay,kd035g6-54nt.txt @@ -0,0 +1,42 @@ +King Display KD035G6-54NT 3.5" (320x240 pixels) 24-bit TFT LCD panel + +Required properties: +- compatible: should be "kingdisplay,kd035g6-54nt" +- power-supply: See panel-common.txt +- reset-gpios: See panel-common.txt + +Optional properties: +- backlight: see panel-common.txt + +The generic bindings for the SPI slaves documented in [1] also apply. + +The device node can contain one 'port' child node with one child +'endpoint' node, according to the bindings defined in [2]. This +node should describe panel's video bus. + +[1]: Documentation/devicetree/bindings/spi/spi-bus.txt +[2]: Documentation/devicetree/bindings/graph.txt + +Example: + +&spi { + panel@0 { + compatible = "kingdisplay,kd035g6-54nt"; + reg = <0>; + + spi-max-frequency = <3125000>; + spi-3wire; + spi-cs-high; + + reset-gpios = <&gpe 2 GPIO_ACTIVE_LOW>; + + backlight = <&backlight>; + power-supply = <&ldo6>; + + port { + panel_input: endpoint { + remote-endpoint = <&panel_output>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/panel/koe,tx14d24vm1bpa.txt b/Documentation/devicetree/bindings/display/panel/koe,tx14d24vm1bpa.txt new file mode 100644 index 000000000000..be7ac666807b --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/koe,tx14d24vm1bpa.txt @@ -0,0 +1,42 @@ +Kaohsiung Opto-Electronics Inc. 5.7" QVGA (320 x 240) TFT LCD panel + +Required properties: +- compatible: should be "koe,tx14d24vm1bpa" +- backlight: phandle of the backlight device attached to the panel +- power-supply: single regulator to provide the supply voltage + +Required nodes: +- port: Parallel port mapping to connect this display + +This panel needs single power supply voltage. Its backlight is conntrolled +via PWM signal. + +Example: +-------- + +Example device-tree definition when connected to iMX53 based board + + lcd_panel: lcd-panel { + compatible = "koe,tx14d24vm1bpa"; + backlight = <&backlight_lcd>; + power-supply = <®_3v3>; + + port { + lcd_panel_in: endpoint { + remote-endpoint = <&lcd_display_out>; + }; + }; + }; + +Then one needs to extend the dispX node: + + lcd_display: disp1 { + + port@1 { + reg = <1>; + + lcd_display_out: endpoint { + remote-endpoint = <&lcd_panel_in>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/lvds.yaml b/Documentation/devicetree/bindings/display/panel/lvds.yaml new file mode 100644 index 000000000000..d0083301acbe --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/lvds.yaml @@ -0,0 +1,107 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/lvds.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: LVDS Display Panel + +maintainers: + - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> + - Thierry Reding <thierry.reding@gmail.com> + +description: |+ + LVDS is a physical layer specification defined in ANSI/TIA/EIA-644-A. Multiple + incompatible data link layers have been used over time to transmit image data + to LVDS panels. This bindings supports display panels compatible with the + following specifications. + + [JEIDA] "Digital Interface Standards for Monitor", JEIDA-59-1999, February + 1999 (Version 1.0), Japan Electronic Industry Development Association (JEIDA) + [LDI] "Open LVDS Display Interface", May 1999 (Version 0.95), National + Semiconductor + [VESA] "VESA Notebook Panel Standard", October 2007 (Version 1.0), Video + Electronics Standards Association (VESA) + + Device compatible with those specifications have been marketed under the + FPD-Link and FlatLink brands. + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + contains: + const: panel-lvds + description: + Shall contain "panel-lvds" in addition to a mandatory panel-specific + compatible string defined in individual panel bindings. The "panel-lvds" + value shall never be used on its own. + + data-mapping: + enum: + - jeida-18 + - jeida-24 + - vesa-24 + description: | + The color signals mapping order. + + LVDS data mappings are defined as follows. + + - "jeida-18" - 18-bit data mapping compatible with the [JEIDA], [LDI] and + [VESA] specifications. Data are transferred as follows on 3 LVDS lanes. + + Slot 0 1 2 3 4 5 6 + ________________ _________________ + Clock \_______________________/ + ______ ______ ______ ______ ______ ______ ______ + DATA0 ><__G0__><__R5__><__R4__><__R3__><__R2__><__R1__><__R0__>< + DATA1 ><__B1__><__B0__><__G5__><__G4__><__G3__><__G2__><__G1__>< + DATA2 ><_CTL2_><_CTL1_><_CTL0_><__B5__><__B4__><__B3__><__B2__>< + + - "jeida-24" - 24-bit data mapping compatible with the [DSIM] and [LDI] + specifications. Data are transferred as follows on 4 LVDS lanes. + + Slot 0 1 2 3 4 5 6 + ________________ _________________ + Clock \_______________________/ + ______ ______ ______ ______ ______ ______ ______ + DATA0 ><__G2__><__R7__><__R6__><__R5__><__R4__><__R3__><__R2__>< + DATA1 ><__B3__><__B2__><__G7__><__G6__><__G5__><__G4__><__G3__>< + DATA2 ><_CTL2_><_CTL1_><_CTL0_><__B7__><__B6__><__B5__><__B4__>< + DATA3 ><_CTL3_><__B1__><__B0__><__G1__><__G0__><__R1__><__R0__>< + + - "vesa-24" - 24-bit data mapping compatible with the [VESA] specification. + Data are transferred as follows on 4 LVDS lanes. + + Slot 0 1 2 3 4 5 6 + ________________ _________________ + Clock \_______________________/ + ______ ______ ______ ______ ______ ______ ______ + DATA0 ><__G0__><__R5__><__R4__><__R3__><__R2__><__R1__><__R0__>< + DATA1 ><__B1__><__B0__><__G5__><__G4__><__G3__><__G2__><__G1__>< + DATA2 ><_CTL2_><_CTL1_><_CTL0_><__B5__><__B4__><__B3__><__B2__>< + DATA3 ><_CTL3_><__B7__><__B6__><__G7__><__G6__><__R7__><__R6__>< + + Control signals are mapped as follows. + + CTL0: HSync + CTL1: VSync + CTL2: Data Enable + CTL3: 0 + + data-mirror: + type: boolean + description: + If set, reverse the bit order described in the data mappings below on all + data lanes, transmitting bits for slots 6 to 0 instead of 0 to 6. + +required: + - compatible + - data-mapping + - width-mm + - height-mm + - panel-timing + - port + +... diff --git a/Documentation/devicetree/bindings/display/panel/mitsubishi,aa104xd12.txt b/Documentation/devicetree/bindings/display/panel/mitsubishi,aa104xd12.txt deleted file mode 100644 index ced0121aed7d..000000000000 --- a/Documentation/devicetree/bindings/display/panel/mitsubishi,aa104xd12.txt +++ /dev/null @@ -1,47 +0,0 @@ -Mitsubishi AA204XD12 LVDS Display Panel -======================================= - -The AA104XD12 is a 10.4" XGA TFT-LCD display panel. - -These DT bindings follow the LVDS panel bindings defined in panel-lvds.txt -with the following device-specific properties. - - -Required properties: - -- compatible: Shall contain "mitsubishi,aa121td01" and "panel-lvds", in that - order. -- vcc-supply: Reference to the regulator powering the panel VCC pins. - - -Example -------- - -panel { - compatible = "mitsubishi,aa104xd12", "panel-lvds"; - vcc-supply = <&vcc_3v3>; - - width-mm = <210>; - height-mm = <158>; - - data-mapping = "jeida-24"; - - panel-timing { - /* 1024x768 @65Hz */ - clock-frequency = <65000000>; - hactive = <1024>; - vactive = <768>; - hsync-len = <136>; - hfront-porch = <20>; - hback-porch = <160>; - vfront-porch = <3>; - vback-porch = <29>; - vsync-len = <6>; - }; - - port { - panel_in: endpoint { - remote-endpoint = <&lvds_encoder>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/display/panel/mitsubishi,aa104xd12.yaml b/Documentation/devicetree/bindings/display/panel/mitsubishi,aa104xd12.yaml new file mode 100644 index 000000000000..b5e7ee230fa6 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/mitsubishi,aa104xd12.yaml @@ -0,0 +1,75 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/mitsubishi,aa104xd12.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mitsubishi AA104XD12 10.4" XGA LVDS Display Panel + +maintainers: + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> + - Thierry Reding <thierry.reding@gmail.com> + +allOf: + - $ref: lvds.yaml# + +properties: + compatible: + items: + - const: mitsubishi,aa104xd12 + - {} # panel-lvds, but not listed here to avoid false select + + vcc-supply: + description: Reference to the regulator powering the panel VCC pins. + + data-mapping: + const: jeida-24 + + width-mm: + const: 210 + + height-mm: + const: 158 + + panel-timing: true + port: true + +additionalProperties: false + +required: + - compatible + - vcc-supply + +examples: + - |+ + + panel { + compatible = "mitsubishi,aa104xd12", "panel-lvds"; + vcc-supply = <&vcc_3v3>; + + width-mm = <210>; + height-mm = <158>; + + data-mapping = "jeida-24"; + + panel-timing { + /* 1024x768 @65Hz */ + clock-frequency = <65000000>; + hactive = <1024>; + vactive = <768>; + hsync-len = <136>; + hfront-porch = <20>; + hback-porch = <160>; + vfront-porch = <3>; + vback-porch = <29>; + vsync-len = <6>; + }; + + port { + panel_in: endpoint { + remote-endpoint = <&lvds_encoder>; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/mitsubishi,aa121td01.txt b/Documentation/devicetree/bindings/display/panel/mitsubishi,aa121td01.txt deleted file mode 100644 index d6e1097504fe..000000000000 --- a/Documentation/devicetree/bindings/display/panel/mitsubishi,aa121td01.txt +++ /dev/null @@ -1,47 +0,0 @@ -Mitsubishi AA121TD01 LVDS Display Panel -======================================= - -The AA121TD01 is a 12.1" WXGA TFT-LCD display panel. - -These DT bindings follow the LVDS panel bindings defined in panel-lvds.txt -with the following device-specific properties. - - -Required properties: - -- compatible: Shall contain "mitsubishi,aa121td01" and "panel-lvds", in that - order. -- vcc-supply: Reference to the regulator powering the panel VCC pins. - - -Example -------- - -panel { - compatible = "mitsubishi,aa121td01", "panel-lvds"; - vcc-supply = <&vcc_3v3>; - - width-mm = <261>; - height-mm = <163>; - - data-mapping = "jeida-24"; - - panel-timing { - /* 1280x800 @60Hz */ - clock-frequency = <71000000>; - hactive = <1280>; - vactive = <800>; - hsync-len = <70>; - hfront-porch = <20>; - hback-porch = <70>; - vsync-len = <5>; - vfront-porch = <3>; - vback-porch = <15>; - }; - - port { - panel_in: endpoint { - remote-endpoint = <&lvds_encoder>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/display/panel/mitsubishi,aa121td01.yaml b/Documentation/devicetree/bindings/display/panel/mitsubishi,aa121td01.yaml new file mode 100644 index 000000000000..977c50a85b67 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/mitsubishi,aa121td01.yaml @@ -0,0 +1,74 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/mitsubishi,aa121td01.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mitsubishi AA121TD01 12.1" WXGA LVDS Display Panel + +maintainers: + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> + - Thierry Reding <thierry.reding@gmail.com> + +allOf: + - $ref: lvds.yaml# + +properties: + compatible: + items: + - const: mitsubishi,aa121td01 + - {} # panel-lvds, but not listed here to avoid false select + + vcc-supply: + description: Reference to the regulator powering the panel VCC pins. + + data-mapping: + const: jeida-24 + + width-mm: + const: 261 + + height-mm: + const: 163 + + panel-timing: true + port: true + +additionalProperties: false + +required: + - compatible + - vcc-supply + +examples: + - |+ + panel { + compatible = "mitsubishi,aa121td01", "panel-lvds"; + vcc-supply = <&vcc_3v3>; + + width-mm = <261>; + height-mm = <163>; + + data-mapping = "jeida-24"; + + panel-timing { + /* 1280x800 @60Hz */ + clock-frequency = <71000000>; + hactive = <1280>; + vactive = <800>; + hsync-len = <70>; + hfront-porch = <20>; + hback-porch = <70>; + vsync-len = <5>; + vfront-porch = <3>; + vback-porch = <15>; + }; + + port { + panel_in: endpoint { + remote-endpoint = <&lvds_encoder>; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/nec,nl8048hl11.yaml b/Documentation/devicetree/bindings/display/panel/nec,nl8048hl11.yaml new file mode 100644 index 000000000000..aa788eaa2f71 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/nec,nl8048hl11.yaml @@ -0,0 +1,62 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/nec,nl8048hl11.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NEC NL8048HL11 4.1" WVGA TFT LCD panel + +description: + The NEC NL8048HL11 is a 4.1" WVGA TFT LCD panel with a 24-bit RGB parallel + data interface and an SPI control interface. + +maintainers: + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: nec,nl8048hl11 + + label: true + port: true + reg: true + reset-gpios: true + + spi-max-frequency: + maximum: 10000000 + +required: + - compatible + - reg + - reset-gpios + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + spi0 { + #address-cells = <1>; + #size-cells = <0>; + + lcd_panel: panel@0 { + compatible = "nec,nl8048hl11"; + reg = <0>; + spi-max-frequency = <10000000>; + + reset-gpios = <&gpio7 7 GPIO_ACTIVE_LOW>; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/ortustech,com37h3m05dtc.txt b/Documentation/devicetree/bindings/display/panel/ortustech,com37h3m05dtc.txt new file mode 100644 index 000000000000..c16907c02f80 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/ortustech,com37h3m05dtc.txt @@ -0,0 +1,12 @@ +OrtusTech COM37H3M05DTC Blanview 3.7" VGA portrait TFT-LCD panel + +Required properties: +- compatible: should be "ortustech,com37h3m05dtc" + +Optional properties: +- enable-gpios: GPIO pin to enable or disable the panel +- backlight: phandle of the backlight device attached to the panel +- power-supply: phandle of the regulator that provides the supply voltage + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/ortustech,com37h3m99dtc.txt b/Documentation/devicetree/bindings/display/panel/ortustech,com37h3m99dtc.txt new file mode 100644 index 000000000000..06a73c3f46b5 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/ortustech,com37h3m99dtc.txt @@ -0,0 +1,12 @@ +OrtusTech COM37H3M99DTC Blanview 3.7" VGA portrait TFT-LCD panel + +Required properties: +- compatible: should be "ortustech,com37h3m99dtc" + +Optional properties: +- enable-gpios: GPIO pin to enable or disable the panel +- backlight: phandle of the backlight device attached to the panel +- power-supply: phandle of the regulator that provides the supply voltage + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/osddisplays,osd101t2045-53ts.txt b/Documentation/devicetree/bindings/display/panel/osddisplays,osd101t2045-53ts.txt new file mode 100644 index 000000000000..85c0b2cacfda --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/osddisplays,osd101t2045-53ts.txt @@ -0,0 +1,11 @@ +One Stop Displays OSD101T2045-53TS 10.1" 1920x1200 panel + +Required properties: +- compatible: should be "osddisplays,osd101t2045-53ts" +- power-supply: as specified in the base binding + +Optional properties: +- backlight: as specified in the base binding + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/osddisplays,osd101t2587-53ts.txt b/Documentation/devicetree/bindings/display/panel/osddisplays,osd101t2587-53ts.txt new file mode 100644 index 000000000000..9d88e96003fc --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/osddisplays,osd101t2587-53ts.txt @@ -0,0 +1,14 @@ +One Stop Displays OSD101T2587-53TS 10.1" 1920x1200 panel + +The panel is similar to OSD101T2045-53TS, but it needs additional +MIPI_DSI_TURN_ON_PERIPHERAL message from the host. + +Required properties: +- compatible: should be "osddisplays,osd101t2587-53ts" +- power-supply: as specified in the base binding + +Optional properties: +- backlight: as specified in the base binding + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/panel-common.txt b/Documentation/devicetree/bindings/display/panel/panel-common.txt deleted file mode 100644 index 5d2519af4bb5..000000000000 --- a/Documentation/devicetree/bindings/display/panel/panel-common.txt +++ /dev/null @@ -1,101 +0,0 @@ -Common Properties for Display Panel -=================================== - -This document defines device tree properties common to several classes of -display panels. It doesn't constitue a device tree binding specification by -itself but is meant to be referenced by device tree bindings. - -When referenced from panel device tree bindings the properties defined in this -document are defined as follows. The panel device tree bindings are -responsible for defining whether each property is required or optional. - - -Descriptive Properties ----------------------- - -- width-mm, -- height-mm: The width-mm and height-mm specify the width and height of the - physical area where images are displayed. These properties are expressed in - millimeters and rounded to the closest unit. - -- label: The label property specifies a symbolic name for the panel as a - string suitable for use by humans. It typically contains a name inscribed on - the system (e.g. as an affixed label) or specified in the system's - documentation (e.g. in the user's manual). - - If no such name exists, and unless the property is mandatory according to - device tree bindings, it shall rather be omitted than constructed of - non-descriptive information. For instance an LCD panel in a system that - contains a single panel shall not be labelled "LCD" if that name is not - inscribed on the system or used in a descriptive fashion in system - documentation. - - -Display Timings ---------------- - -- panel-timing: Most display panels are restricted to a single resolution and - require specific display timings. The panel-timing subnode expresses those - timings as specified in the timing subnode section of the display timing - bindings defined in - Documentation/devicetree/bindings/display/panel/display-timing.txt. - - -Connectivity ------------- - -- ports: Panels receive video data through one or multiple connections. While - the nature of those connections is specific to the panel type, the - connectivity is expressed in a standard fashion using ports as specified in - the device graph bindings defined in - Documentation/devicetree/bindings/graph.txt. - -- ddc-i2c-bus: Some panels expose EDID information through an I2C-compatible - bus such as DDC2 or E-DDC. For such panels the ddc-i2c-bus contains a - phandle to the system I2C controller connected to that bus. - - -Control I/Os ------------- - -Many display panels can be controlled through pins driven by GPIOs. The nature -and timing of those control signals are device-specific and left for panel -device tree bindings to specify. The following GPIO specifiers can however be -used for panels that implement compatible control signals. - -- enable-gpios: Specifier for a GPIO connected to the panel enable control - signal. The enable signal is active high and enables operation of the panel. - This property can also be used for panels implementing an active low power - down signal, which is a negated version of the enable signal. Active low - enable signals (or active high power down signals) can be supported by - inverting the GPIO specifier polarity flag. - - Note that the enable signal control panel operation only and must not be - confused with a backlight enable signal. - -- reset-gpios: Specifier for a GPIO coonnected to the panel reset control - signal. The reset signal is active low and resets the panel internal logic - while active. Active high reset signals can be supported by inverting the - GPIO specifier polarity flag. - -Power ------ - -- power-supply: display panels require power to be supplied. While several - panels need more than one power supply with panel-specific constraints - governing the order and timings of the power supplies, in many cases a single - power supply is sufficient, either because the panel has a single power rail, - or because all its power rails can be driven by the same supply. In that case - the power-supply property specifies the supply powering the panel as a phandle - to a regulator. - -Backlight ---------- - -Most display panels include a backlight. Some of them also include a backlight -controller exposed through a control bus such as I2C or DSI. Others expose -backlight control through GPIO, PWM or other signals connected to an external -backlight controller. - -- backlight: For panels whose backlight is controlled by an external backlight - controller, this property contains a phandle that references the controller. diff --git a/Documentation/devicetree/bindings/display/panel/panel-common.yaml b/Documentation/devicetree/bindings/display/panel/panel-common.yaml new file mode 100644 index 000000000000..ef8d8cdfcede --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/panel-common.yaml @@ -0,0 +1,149 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/panel-common.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Common Properties for Display Panels + +maintainers: + - Thierry Reding <thierry.reding@gmail.com> + - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> + +description: | + This document defines device tree properties common to several classes of + display panels. It doesn't constitue a device tree binding specification by + itself but is meant to be referenced by device tree bindings. + + When referenced from panel device tree bindings the properties defined in this + document are defined as follows. The panel device tree bindings are + responsible for defining whether each property is required or optional. + +properties: + # Descriptive Properties + width-mm: + description: + Specifies the width of the physical area where images are displayed. This + property is expressed in millimeters and rounded to the closest unit. + + height-mm: + description: + Specifies the height of the physical area where images are displayed. This + property is expressed in millimeters and rounded to the closest unit. + + label: + description: | + The label property specifies a symbolic name for the panel as a + string suitable for use by humans. It typically contains a name inscribed + on the system (e.g. as an affixed label) or specified in the system's + documentation (e.g. in the user's manual). + + If no such name exists, and unless the property is mandatory according to + device tree bindings, it shall rather be omitted than constructed of + non-descriptive information. For instance an LCD panel in a system that + contains a single panel shall not be labelled "LCD" if that name is not + inscribed on the system or used in a descriptive fashion in system + documentation. + + rotation: + description: + Display rotation in degrees counter clockwise (0,90,180,270) + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 0, 90, 180, 270 ] + + # Display Timings + panel-timing: + type: object + description: + Most display panels are restricted to a single resolution and + require specific display timings. The panel-timing subnode expresses those + timings as specified in the timing subnode section of the display timing + bindings defined in + Documentation/devicetree/bindings/display/panel/display-timing.txt. + + # Connectivity + port: + type: object + + ports: + type: object + description: + Panels receive video data through one or multiple connections. While + the nature of those connections is specific to the panel type, the + connectivity is expressed in a standard fashion using ports as specified + in the device graph bindings defined in + Documentation/devicetree/bindings/graph.txt. + + ddc-i2c-bus: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Some panels expose EDID information through an I2C-compatible + bus such as DDC2 or E-DDC. For such panels the ddc-i2c-bus contains a + phandle to the system I2C controller connected to that bus. + + no-hpd: + type: boolean + description: + This panel is supposed to communicate that it's ready via HPD + (hot plug detect) signal, but the signal isn't hooked up so we should + hardcode the max delay from the panel spec when powering up the panel. + + # Control I/Os + + # Many display panels can be controlled through pins driven by GPIOs. The nature + # and timing of those control signals are device-specific and left for panel + # device tree bindings to specify. The following GPIO specifiers can however be + # used for panels that implement compatible control signals. + + enable-gpios: + maxItems: 1 + description: | + Specifier for a GPIO connected to the panel enable control signal. The + enable signal is active high and enables operation of the panel. This + property can also be used for panels implementing an active low power down + signal, which is a negated version of the enable signal. Active low enable + signals (or active high power down signals) can be supported by inverting + the GPIO specifier polarity flag. + + Note that the enable signal control panel operation only and must not be + confused with a backlight enable signal. + + reset-gpios: + maxItems: 1 + description: + Specifier for a GPIO connected to the panel reset control signal. + The reset signal is active low and resets the panel internal logic + while active. Active high reset signals can be supported by inverting the + GPIO specifier polarity flag. + + # Power + power-supply: + description: + Display panels require power to be supplied. While several panels need + more than one power supply with panel-specific constraints governing the + order and timings of the power supplies, in many cases a single power + supply is sufficient, either because the panel has a single power rail, or + because all its power rails can be driven by the same supply. In that case + the power-supply property specifies the supply powering the panel as a + phandle to a regulator. + + # Backlight + + # Most display panels include a backlight. Some of them also include a backlight + # controller exposed through a control bus such as I2C or DSI. Others expose + # backlight control through GPIO, PWM or other signals connected to an external + # backlight controller. + + backlight: + $ref: /schemas/types.yaml#/definitions/phandle + description: + For panels whose backlight is controlled by an external backlight + controller, this property contains a phandle that references the + controller. + +dependencies: + width-mm: [ height-mm ] + height-mm: [ width-mm ] + +... diff --git a/Documentation/devicetree/bindings/display/panel/panel-lvds.txt b/Documentation/devicetree/bindings/display/panel/panel-lvds.txt deleted file mode 100644 index 250850a2150b..000000000000 --- a/Documentation/devicetree/bindings/display/panel/panel-lvds.txt +++ /dev/null @@ -1,121 +0,0 @@ -LVDS Display Panel -================== - -LVDS is a physical layer specification defined in ANSI/TIA/EIA-644-A. Multiple -incompatible data link layers have been used over time to transmit image data -to LVDS panels. This bindings supports display panels compatible with the -following specifications. - -[JEIDA] "Digital Interface Standards for Monitor", JEIDA-59-1999, February -1999 (Version 1.0), Japan Electronic Industry Development Association (JEIDA) -[LDI] "Open LVDS Display Interface", May 1999 (Version 0.95), National -Semiconductor -[VESA] "VESA Notebook Panel Standard", October 2007 (Version 1.0), Video -Electronics Standards Association (VESA) - -Device compatible with those specifications have been marketed under the -FPD-Link and FlatLink brands. - - -Required properties: - -- compatible: Shall contain "panel-lvds" in addition to a mandatory - panel-specific compatible string defined in individual panel bindings. The - "panel-lvds" value shall never be used on its own. -- width-mm: See panel-common.txt. -- height-mm: See panel-common.txt. -- data-mapping: The color signals mapping order, "jeida-18", "jeida-24" - or "vesa-24". - -Optional properties: - -- label: See panel-common.txt. -- gpios: See panel-common.txt. -- backlight: See panel-common.txt. -- power-supply: See panel-common.txt. -- data-mirror: If set, reverse the bit order described in the data mappings - below on all data lanes, transmitting bits for slots 6 to 0 instead of - 0 to 6. - -Required nodes: - -- panel-timing: See panel-common.txt. -- ports: See panel-common.txt. These bindings require a single port subnode - corresponding to the panel LVDS input. - - -LVDS data mappings are defined as follows. - -- "jeida-18" - 18-bit data mapping compatible with the [JEIDA], [LDI] and - [VESA] specifications. Data are transferred as follows on 3 LVDS lanes. - -Slot 0 1 2 3 4 5 6 - ________________ _________________ -Clock \_______________________/ - ______ ______ ______ ______ ______ ______ ______ -DATA0 ><__G0__><__R5__><__R4__><__R3__><__R2__><__R1__><__R0__>< -DATA1 ><__B1__><__B0__><__G5__><__G4__><__G3__><__G2__><__G1__>< -DATA2 ><_CTL2_><_CTL1_><_CTL0_><__B5__><__B4__><__B3__><__B2__>< - -- "jeida-24" - 24-bit data mapping compatible with the [DSIM] and [LDI] - specifications. Data are transferred as follows on 4 LVDS lanes. - -Slot 0 1 2 3 4 5 6 - ________________ _________________ -Clock \_______________________/ - ______ ______ ______ ______ ______ ______ ______ -DATA0 ><__G2__><__R7__><__R6__><__R5__><__R4__><__R3__><__R2__>< -DATA1 ><__B3__><__B2__><__G7__><__G6__><__G5__><__G4__><__G3__>< -DATA2 ><_CTL2_><_CTL1_><_CTL0_><__B7__><__B6__><__B5__><__B4__>< -DATA3 ><_CTL3_><__B1__><__B0__><__G1__><__G0__><__R1__><__R0__>< - -- "vesa-24" - 24-bit data mapping compatible with the [VESA] specification. - Data are transferred as follows on 4 LVDS lanes. - -Slot 0 1 2 3 4 5 6 - ________________ _________________ -Clock \_______________________/ - ______ ______ ______ ______ ______ ______ ______ -DATA0 ><__G0__><__R5__><__R4__><__R3__><__R2__><__R1__><__R0__>< -DATA1 ><__B1__><__B0__><__G5__><__G4__><__G3__><__G2__><__G1__>< -DATA2 ><_CTL2_><_CTL1_><_CTL0_><__B5__><__B4__><__B3__><__B2__>< -DATA3 ><_CTL3_><__B7__><__B6__><__G7__><__G6__><__R7__><__R6__>< - -Control signals are mapped as follows. - -CTL0: HSync -CTL1: VSync -CTL2: Data Enable -CTL3: 0 - - -Example -------- - -panel { - compatible = "mitsubishi,aa121td01", "panel-lvds"; - - width-mm = <261>; - height-mm = <163>; - - data-mapping = "jeida-24"; - - panel-timing { - /* 1280x800 @60Hz */ - clock-frequency = <71000000>; - hactive = <1280>; - vactive = <800>; - hsync-len = <70>; - hfront-porch = <20>; - hback-porch = <70>; - vsync-len = <5>; - vfront-porch = <3>; - vback-porch = <15>; - }; - - port { - panel_in: endpoint { - remote-endpoint = <&lvds_encoder>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/display/panel/panel.txt b/Documentation/devicetree/bindings/display/panel/panel.txt deleted file mode 100644 index e2e6867852b8..000000000000 --- a/Documentation/devicetree/bindings/display/panel/panel.txt +++ /dev/null @@ -1,4 +0,0 @@ -Common display properties -------------------------- - -- rotation: Display rotation in degrees counter clockwise (0,90,180,270) diff --git a/Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.txt b/Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.txt deleted file mode 100644 index 1639fb17a9f0..000000000000 --- a/Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.txt +++ /dev/null @@ -1,14 +0,0 @@ -PDA 91-00156-A0 5.0" WVGA TFT LCD panel - -Required properties: -- compatible: should be "pda,91-00156-a0" -- power-supply: this panel requires a single power supply. A phandle to a -regulator needs to be specified here. Compatible with panel-common binding which -is specified in the panel-common.txt in this directory. -- backlight: this panel's backlight is controlled by an external backlight -controller. A phandle to this controller needs to be specified here. -Compatible with panel-common binding which is specified in the panel-common.txt -in this directory. - -This binding is compatible with the simple-panel binding, which is specified -in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.yaml b/Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.yaml new file mode 100644 index 000000000000..ccd3623b4955 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.yaml @@ -0,0 +1,31 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/pda,91-00156-a0.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: PDA 91-00156-A0 5.0" WVGA TFT LCD panel + +maintainers: + - Cristian Birsan <cristian.birsan@microchip.com> + - Thierry Reding <thierry.reding@gmail.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: pda,91-00156-a0 + + power-supply: true + backlight: true + port: true + +additionalProperties: false + +required: + - compatible + - power-supply + - backlight + +... diff --git a/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.txt b/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.txt deleted file mode 100644 index e9e19c059260..000000000000 --- a/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.txt +++ /dev/null @@ -1,49 +0,0 @@ -This binding covers the official 7" (800x480) Raspberry Pi touchscreen -panel. - -This DSI panel contains: - -- TC358762 DSI->DPI bridge -- Atmel microcontroller on I2C for power sequencing the DSI bridge and - controlling backlight -- Touchscreen controller on I2C for touch input - -and this binding covers the DSI display parts but not its touch input. - -Required properties: -- compatible: Must be "raspberrypi,7inch-touchscreen-panel" -- reg: Must be "45" -- port: See panel-common.txt - -Example: - -dsi1: dsi@7e700000 { - #address-cells = <1>; - #size-cells = <0>; - <...> - - port { - dsi_out_port: endpoint { - remote-endpoint = <&panel_dsi_port>; - }; - }; -}; - -i2c_dsi: i2c { - compatible = "i2c-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&gpio 28 0 - &gpio 29 0>; - - lcd@45 { - compatible = "raspberrypi,7inch-touchscreen-panel"; - reg = <0x45>; - - port { - panel_dsi_port: endpoint { - remote-endpoint = <&dsi_out_port>; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.yaml b/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.yaml new file mode 100644 index 000000000000..22a083f7bc8e --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.yaml @@ -0,0 +1,71 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/raspberrypi,7inch-touchscreen.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: The official 7" (800x480) Raspberry Pi touchscreen + +maintainers: + - Eric Anholt <eric@anholt.net> + - Thierry Reding <thierry.reding@gmail.com> + +description: |+ + This DSI panel contains: + + - TC358762 DSI->DPI bridge + - Atmel microcontroller on I2C for power sequencing the DSI bridge and + controlling backlight + - Touchscreen controller on I2C for touch input + + and this binding covers the DSI display parts but not its touch input. + +properties: + compatible: + const: raspberrypi,7inch-touchscreen-panel + + reg: + const: 0x45 + + port: true + +required: + - compatible + - reg + - port + +additionalProperties: false + +examples: + - |+ + dsi1: dsi { + #address-cells = <1>; + #size-cells = <0>; + + port { + dsi_out_port: endpoint { + remote-endpoint = <&panel_dsi_port>; + }; + }; + }; + + i2c_dsi: i2c { + compatible = "i2c-gpio"; + #address-cells = <1>; + #size-cells = <0>; + scl-gpios = <&gpio 28 0>; + sda-gpios = <&gpio 29 0>; + + lcd@45 { + compatible = "raspberrypi,7inch-touchscreen-panel"; + reg = <0x45>; + + port { + panel_dsi_port: endpoint { + remote-endpoint = <&dsi_out_port>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/raydium,rm67191.txt b/Documentation/devicetree/bindings/display/panel/raydium,rm67191.txt new file mode 100644 index 000000000000..10424695aa02 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/raydium,rm67191.txt @@ -0,0 +1,41 @@ +Raydium RM67171 OLED LCD panel with MIPI-DSI protocol + +Required properties: +- compatible: "raydium,rm67191" +- reg: virtual channel for MIPI-DSI protocol + must be <0> +- dsi-lanes: number of DSI lanes to be used + must be <3> or <4> +- port: input port node with endpoint definition as + defined in Documentation/devicetree/bindings/graph.txt; + the input port should be connected to a MIPI-DSI device + driver + +Optional properties: +- reset-gpios: a GPIO spec for the RST_B GPIO pin +- v3p3-supply: phandle to 3.3V regulator that powers the VDD_3V3 pin +- v1p8-supply: phandle to 1.8V regulator that powers the VDD_1V8 pin +- width-mm: see panel-common.txt +- height-mm: see panel-common.txt +- video-mode: 0 - burst-mode + 1 - non-burst with sync event + 2 - non-burst with sync pulse + +Example: + + panel@0 { + compatible = "raydium,rm67191"; + reg = <0>; + pinctrl-0 = <&pinctrl_mipi_dsi_0_1_en>; + pinctrl-names = "default"; + reset-gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + dsi-lanes = <4>; + width-mm = <68>; + height-mm = <121>; + + port { + panel_in: endpoint { + remote-endpoint = <&mipi_out>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.txt b/Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.txt index 1b5763200cf6..a372c5d84695 100644 --- a/Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.txt +++ b/Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.txt @@ -5,6 +5,9 @@ Required properties: - reg: DSI virtual channel of the peripheral - reset-gpios: panel reset gpio - backlight: phandle of the backlight device attached to the panel +- vcc-supply: phandle of the regulator that provides the vcc supply voltage. +- iovcc-supply: phandle of the regulator that provides the iovcc supply + voltage. Example: @@ -14,5 +17,7 @@ Example: reg = <0>; backlight = <&backlight>; reset-gpios = <&gpio3 13 GPIO_ACTIVE_LOW>; + vcc-supply = <®_2v8_p>; + iovcc-supply = <®_1v8_p>; }; }; diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e63m0.txt b/Documentation/devicetree/bindings/display/panel/samsung,s6e63m0.txt new file mode 100644 index 000000000000..9fb9ebeef8e4 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/samsung,s6e63m0.txt @@ -0,0 +1,33 @@ +Samsung s6e63m0 AMOLED LCD panel + +Required properties: + - compatible: "samsung,s6e63m0" + - reset-gpios: GPIO spec for reset pin + - vdd3-supply: VDD regulator + - vci-supply: VCI regulator + +The panel must obey rules for SPI slave device specified in document [1]. + +The device node can contain one 'port' child node with one child +'endpoint' node, according to the bindings defined in [2]. This +node should describe panel's video bus. + +[1]: Documentation/devicetree/bindings/spi/spi-bus.txt +[2]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + + s6e63m0: display@0 { + compatible = "samsung,s6e63m0"; + reg = <0>; + reset-gpio = <&mp05 5 1>; + vdd3-supply = <&ldo12_reg>; + vci-supply = <&ldo11_reg>; + spi-max-frequency = <1200000>; + + port { + lcd_ep: endpoint { + remote-endpoint = <&fimd_ep>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt b/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt deleted file mode 100644 index d06644b555bd..000000000000 --- a/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt +++ /dev/null @@ -1,41 +0,0 @@ -Solomon Goldentek Display GKTW70SDAE4SE LVDS Display Panel -========================================================== - -The GKTW70SDAE4SE is a 7" WVGA TFT-LCD display panel. - -These DT bindings follow the LVDS panel bindings defined in panel-lvds.txt -with the following device-specific properties. - -Required properties: - -- compatible: Shall contain "sgd,gktw70sdae4se" and "panel-lvds", in that order. - -Example -------- - -panel { - compatible = "sgd,gktw70sdae4se", "panel-lvds"; - - width-mm = <153>; - height-mm = <86>; - - data-mapping = "jeida-18"; - - panel-timing { - clock-frequency = <32000000>; - hactive = <800>; - vactive = <480>; - hback-porch = <39>; - hfront-porch = <39>; - vback-porch = <29>; - vfront-porch = <13>; - hsync-len = <47>; - vsync-len = <2>; - }; - - port { - panel_in: endpoint { - remote-endpoint = <&lvds_encoder>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.yaml b/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.yaml new file mode 100644 index 000000000000..e63a570ae59d --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.yaml @@ -0,0 +1,68 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/sgd,gktw70sdae4se.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Solomon Goldentek Display GKTW70SDAE4SE 7" WVGA LVDS Display Panel + +maintainers: + - Neil Armstrong <narmstrong@baylibre.com> + - Thierry Reding <thierry.reding@gmail.com> + +allOf: + - $ref: lvds.yaml# + +properties: + compatible: + items: + - const: sgd,gktw70sdae4se + - {} # panel-lvds, but not listed here to avoid false select + + data-mapping: + const: jeida-18 + + width-mm: + const: 153 + + height-mm: + const: 86 + + panel-timing: true + port: true + +additionalProperties: false + +required: + - compatible + +examples: + - |+ + panel { + compatible = "sgd,gktw70sdae4se", "panel-lvds"; + + width-mm = <153>; + height-mm = <86>; + + data-mapping = "jeida-18"; + + panel-timing { + clock-frequency = <32000000>; + hactive = <800>; + vactive = <480>; + hback-porch = <39>; + hfront-porch = <39>; + vback-porch = <29>; + vfront-porch = <13>; + hsync-len = <47>; + vsync-len = <2>; + }; + + port { + panel_in: endpoint { + remote-endpoint = <&lvds_encoder>; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/sharp,ld-d5116z01b.txt b/Documentation/devicetree/bindings/display/panel/sharp,ld-d5116z01b.txt new file mode 100644 index 000000000000..fd9cf39bde77 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sharp,ld-d5116z01b.txt @@ -0,0 +1,26 @@ +Sharp LD-D5116Z01B 12.3" WUXGA+ eDP panel + +Required properties: +- compatible: should be "sharp,ld-d5116z01b" +- power-supply: regulator to provide the VCC supply voltage (3.3 volts) + +This binding is compatible with the simple-panel binding. + +The device node can contain one 'port' child node with one child +'endpoint' node, according to the bindings defined in [1]. This +node should describe panel's video bus. + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + + panel: panel { + compatible = "sharp,ld-d5116z01b"; + power-supply = <&vlcd_3v3>; + + port { + panel_ep: endpoint { + remote-endpoint = <&bridge_out_ep>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/sharp,lq070y3dg3b.txt b/Documentation/devicetree/bindings/display/panel/sharp,lq070y3dg3b.txt new file mode 100644 index 000000000000..95534b55ee5f --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sharp,lq070y3dg3b.txt @@ -0,0 +1,12 @@ +Sharp LQ070Y3DG3B 7.0" WVGA landscape TFT LCD panel + +Required properties: +- compatible: should be "sharp,lq070y3dg3b" + +Optional properties: +- enable-gpios: GPIO pin to enable or disable the panel +- backlight: phandle of the backlight device attached to the panel +- power-supply: phandle of the regulator that provides the supply voltage + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/sharp,ls020b1dd01d.txt b/Documentation/devicetree/bindings/display/panel/sharp,ls020b1dd01d.txt new file mode 100644 index 000000000000..e45edbc565a3 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sharp,ls020b1dd01d.txt @@ -0,0 +1,12 @@ +Sharp 2.0" (240x160 pixels) 16-bit TFT LCD panel + +Required properties: +- compatible: should be "sharp,ls020b1dd01d" +- power-supply: as specified in the base binding + +Optional properties: +- backlight: as specified in the base binding +- enable-gpios: as specified in the base binding + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/simple-panel.txt b/Documentation/devicetree/bindings/display/panel/simple-panel.txt index b2b872c710f2..e11208fb7da8 100644 --- a/Documentation/devicetree/bindings/display/panel/simple-panel.txt +++ b/Documentation/devicetree/bindings/display/panel/simple-panel.txt @@ -1,28 +1 @@ -Simple display panel -==================== - -panel node ----------- - -Required properties: -- power-supply: See panel-common.txt - -Optional properties: -- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing -- enable-gpios: GPIO pin to enable or disable the panel -- backlight: phandle of the backlight device attached to the panel -- no-hpd: This panel is supposed to communicate that it's ready via HPD - (hot plug detect) signal, but the signal isn't hooked up so we should - hardcode the max delay from the panel spec when powering up the panel. - -Example: - - panel: panel { - compatible = "cptt,claa101wb01"; - ddc-i2c-bus = <&panelddc>; - - power-supply = <&vdd_pnl_reg>; - enable-gpios = <&gpio 90 0>; - - backlight = <&backlight>; - }; +See panel-common.yaml in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.yaml b/Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.yaml new file mode 100644 index 000000000000..9e5994417c12 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.yaml @@ -0,0 +1,33 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/tfc,s9700rtwv43tr-01b.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TFC S9700RTWV43TR-01B 7" Three Five Corp 800x480 LCD panel with resistive touch + +maintainers: + - Jyri Sarha <jsarha@ti.com> + - Thierry Reding <thierry.reding@gmail.com> + +description: |+ + The panel is found on TI AM335x-evm. + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: tfc,s9700rtwv43tr-01b + + enable-gpios: true + backlight: true + port: true + +additionalProperties: false + +required: + - compatible + - power-supply + +... diff --git a/Documentation/devicetree/bindings/display/panel/ti,nspire.yaml b/Documentation/devicetree/bindings/display/panel/ti,nspire.yaml new file mode 100644 index 000000000000..5c5a3b519e31 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/ti,nspire.yaml @@ -0,0 +1,36 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/ti,nspire.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments NSPIRE Display Panels + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + enum: + - ti,nspire-cx-lcd-panel + - ti,nspire-classic-lcd-panel + port: true + +required: + - compatible + +additionalProperties: false + +examples: + - | + panel { + compatible = "ti,nspire-cx-lcd-panel"; + port { + panel_in: endpoint { + remote-endpoint = <&pads>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/tpo,tpg110.txt b/Documentation/devicetree/bindings/display/panel/tpo,tpg110.txt deleted file mode 100644 index 40f3d7c713bb..000000000000 --- a/Documentation/devicetree/bindings/display/panel/tpo,tpg110.txt +++ /dev/null @@ -1,70 +0,0 @@ -TPO TPG110 Panel -================ - -This panel driver is a component that acts as an intermediary -between an RGB output and a variety of panels. The panel -driver is strapped up in electronics to the desired resolution -and other properties, and has a control interface over 3WIRE -SPI. By talking to the TPG110 over SPI, the strapped properties -can be discovered and the hardware is therefore mostly -self-describing. - - +--------+ -SPI -> | TPO | -> physical display -RGB -> | TPG110 | - +--------+ - -If some electrical strap or alternate resolution is desired, -this can be set up by taking software control of the display -over the SPI interface. The interface can also adjust -for properties of the display such as gamma correction and -certain electrical driving levels. - -The TPG110 does not know the physical dimensions of the panel -connected, so this needs to be specified in the device tree. - -It requires a GPIO line for control of its reset line. - -The serial protocol has line names that resemble I2C but the -protocol is not I2C but 3WIRE SPI. - -Required properties: -- compatible : one of: - "ste,nomadik-nhk15-display", "tpo,tpg110" - "tpo,tpg110" -- grestb-gpios : panel reset GPIO -- width-mm : see display/panel/panel-common.txt -- height-mm : see display/panel/panel-common.txt - -The device needs to be a child of an SPI bus, see -spi/spi-bus.txt. The SPI child must set the following -properties: -- spi-3wire -- spi-max-frequency = <3000000>; -as these are characteristics of this device. - -The device node can contain one 'port' child node with one child -'endpoint' node, according to the bindings defined in -media/video-interfaces.txt. This node should describe panel's video bus. - -Example -------- - -panel: display@0 { - compatible = "tpo,tpg110"; - reg = <0>; - spi-3wire; - /* 320 ns min period ~= 3 MHz */ - spi-max-frequency = <3000000>; - /* Width and height from data sheet */ - width-mm = <116>; - height-mm = <87>; - grestb-gpios = <&foo_gpio 5 GPIO_ACTIVE_LOW>; - backlight = <&bl>; - - port { - nomadik_clcd_panel: endpoint { - remote-endpoint = <&foo>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/display/panel/tpo,tpg110.yaml b/Documentation/devicetree/bindings/display/panel/tpo,tpg110.yaml new file mode 100644 index 000000000000..a51660b73f28 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/tpo,tpg110.yaml @@ -0,0 +1,101 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/tpo,tpg110.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TPO TPG110 Panel + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + - Thierry Reding <thierry.reding@gmail.com> + +description: |+ + This panel driver is a component that acts as an intermediary + between an RGB output and a variety of panels. The panel + driver is strapped up in electronics to the desired resolution + and other properties, and has a control interface over 3WIRE + SPI. By talking to the TPG110 over SPI, the strapped properties + can be discovered and the hardware is therefore mostly + self-describing. + + +--------+ + SPI -> | TPO | -> physical display + RGB -> | TPG110 | + +--------+ + + If some electrical strap or alternate resolution is desired, + this can be set up by taking software control of the display + over the SPI interface. The interface can also adjust + for properties of the display such as gamma correction and + certain electrical driving levels. + + The TPG110 does not know the physical dimensions of the panel + connected, so this needs to be specified in the device tree. + + It requires a GPIO line for control of its reset line. + + The serial protocol has line names that resemble I2C but the + protocol is not I2C but 3WIRE SPI. + + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - ste,nomadik-nhk15-display + - const: tpo,tpg110 + - const: tpo,tpg110 + + reg: true + + grestb-gpios: + maxItems: 1 + description: panel reset GPIO + + spi-3wire: true + + spi-max-frequency: + const: 3000000 + +required: + - compatible + - reg + - grestb-gpios + - width-mm + - height-mm + - spi-3wire + - spi-max-frequency + - port + +examples: + - |+ + spi { + #address-cells = <1>; + #size-cells = <0>; + + panel: display@0 { + compatible = "tpo,tpg110"; + reg = <0>; + spi-3wire; + /* 320 ns min period ~= 3 MHz */ + spi-max-frequency = <3000000>; + /* Width and height from data sheet */ + width-mm = <116>; + height-mm = <87>; + grestb-gpios = <&foo_gpio 5 1>; + backlight = <&bl>; + + port { + nomadik_clcd_panel: endpoint { + remote-endpoint = <&foo>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/vl050_8048nt_c01.txt b/Documentation/devicetree/bindings/display/panel/vl050_8048nt_c01.txt new file mode 100644 index 000000000000..b42bf06bbd99 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/vl050_8048nt_c01.txt @@ -0,0 +1,12 @@ +VXT 800x480 color TFT LCD panel + +Required properties: +- compatible: should be "vxt,vl050-8048nt-c01" +- power-supply: as specified in the base binding + +Optional properties: +- backlight: as specified in the base binding +- enable-gpios: as specified in the base binding + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/renesas,du.txt b/Documentation/devicetree/bindings/display/renesas,du.txt index aedb22b4d161..c97dfacad281 100644 --- a/Documentation/devicetree/bindings/display/renesas,du.txt +++ b/Documentation/devicetree/bindings/display/renesas,du.txt @@ -7,6 +7,7 @@ Required Properties: - "renesas,du-r8a7744" for R8A7744 (RZ/G1N) compatible DU - "renesas,du-r8a7745" for R8A7745 (RZ/G1E) compatible DU - "renesas,du-r8a77470" for R8A77470 (RZ/G1C) compatible DU + - "renesas,du-r8a774a1" for R8A774A1 (RZ/G2M) compatible DU - "renesas,du-r8a774c0" for R8A774C0 (RZ/G2E) compatible DU - "renesas,du-r8a7779" for R8A7779 (R-Car H1) compatible DU - "renesas,du-r8a7790" for R8A7790 (R-Car H2) compatible DU @@ -58,6 +59,7 @@ corresponding to each DU output. R8A7744 (RZ/G1N) DPAD 0 LVDS 0 - - R8A7745 (RZ/G1E) DPAD 0 DPAD 1 - - R8A77470 (RZ/G1C) DPAD 0 DPAD 1 LVDS 0 - + R8A774A1 (RZ/G2M) DPAD 0 HDMI 0 LVDS 0 - R8A774C0 (RZ/G2E) DPAD 0 LVDS 0 LVDS 1 - R8A7779 (R-Car H1) DPAD 0 DPAD 1 - - R8A7790 (R-Car H2) DPAD 0 LVDS 0 LVDS 1 - diff --git a/Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt index 39143424a474..3d32ce137e7f 100644 --- a/Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt +++ b/Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt @@ -12,6 +12,7 @@ following device-specific properties. Required properties: - compatible: should be one of the following: + "rockchip,rk3228-dw-hdmi" "rockchip,rk3288-dw-hdmi" "rockchip,rk3328-dw-hdmi" "rockchip,rk3399-dw-hdmi" @@ -38,6 +39,13 @@ Optional properties - phys: from general PHY binding: the phandle for the PHY device. - phy-names: Should be "hdmi" if phys references an external phy. +Optional pinctrl entry: +- If you have both a "unwedge" and "default" pinctrl entry, dw_hdmi + will switch to the unwedge pinctrl state for 10ms if it ever gets an + i2c timeout. It's intended that this unwedge pinctrl entry will + cause the SDA line to be driven low to work around a hardware + errata. + Example: hdmi: hdmi@ff980000 { diff --git a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt index 6bb59ab39f2f..ce4c1fc9116c 100644 --- a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt +++ b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt @@ -14,6 +14,8 @@ Required properties: - rockchip,grf: this soc should set GRF regs to mux vopl/vopb. - ports: contain a port node with endpoint definitions as defined in [2]. For vopb,set the reg = <0> and set the reg = <1> for vopl. +- video port 0 for the VOP input, the remote endpoint maybe vopb or vopl +- video port 1 for either a panel or subsequent encoder Optional properties: - power-domains: a phandle to mipi dsi power domain node. @@ -40,11 +42,12 @@ Example: ports { #address-cells = <1>; #size-cells = <0>; - reg = <1>; - mipi_in: port { + mipi_in: port@0 { + reg = <0>; #address-cells = <1>; #size-cells = <0>; + mipi_in_vopb: endpoint@0 { reg = <0>; remote-endpoint = <&vopb_out_mipi>; @@ -54,6 +57,16 @@ Example: remote-endpoint = <&vopl_out_mipi>; }; }; + + mipi_out: port@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + mipi_out_panel: endpoint { + remote-endpoint = <&panel_in_mipi>; + }; + }; }; panel { @@ -64,5 +77,11 @@ Example: pinctrl-names = "default"; pinctrl-0 = <&lcd_en>; backlight = <&backlight>; + + port { + panel_in_mipi: endpoint { + remote-endpoint = <&mipi_out_panel>; + }; + }; }; }; diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip-lvds.txt b/Documentation/devicetree/bindings/display/rockchip/rockchip-lvds.txt index da6939efdb43..7849ff039229 100644 --- a/Documentation/devicetree/bindings/display/rockchip/rockchip-lvds.txt +++ b/Documentation/devicetree/bindings/display/rockchip/rockchip-lvds.txt @@ -32,17 +32,6 @@ Their connections are modeled using the OF graph bindings specified in - video port 0 for the VOP input, the remote endpoint maybe vopb or vopl - video port 1 for either a panel or subsequent encoder -the lvds panel described by - Documentation/devicetree/bindings/display/panel/simple-panel.txt - -Panel required properties: -- ports for remote LVDS output - -Panel optional properties: -- data-mapping: should be "vesa-24","jeida-24" or "jeida-18". -This describes decribed by: - Documentation/devicetree/bindings/display/panel/panel-lvds.txt - Example: lvds_panel: lvds-panel { diff --git a/Documentation/devicetree/bindings/display/simple-framebuffer.yaml b/Documentation/devicetree/bindings/display/simple-framebuffer.yaml index b052d76cf8b6..678776b6012a 100644 --- a/Documentation/devicetree/bindings/display/simple-framebuffer.yaml +++ b/Documentation/devicetree/bindings/display/simple-framebuffer.yaml @@ -126,6 +126,28 @@ required: # but usually they will be filled by the bootloader. - compatible +allOf: + - if: + properties: + compatible: + contains: + const: allwinner,simple-framebuffer + + then: + required: + - allwinner,pipeline + + - if: + properties: + compatible: + contains: + const: amlogic,simple-framebuffer + + then: + required: + - amlogic,pipeline + + additionalProperties: false examples: @@ -139,7 +161,8 @@ examples: #size-cells = <1>; stdout-path = "display0"; framebuffer0: framebuffer@1d385000 { - compatible = "simple-framebuffer"; + compatible = "allwinner,simple-framebuffer", "simple-framebuffer"; + allwinner,pipeline = "de_be0-lcd0"; reg = <0x1d385000 3840000>; width = <1600>; height = <1200>; diff --git a/Documentation/devicetree/bindings/display/ssd1307fb.txt b/Documentation/devicetree/bindings/display/ssd1307fb.txt index b67f8caa212c..27333b9551b3 100644 --- a/Documentation/devicetree/bindings/display/ssd1307fb.txt +++ b/Documentation/devicetree/bindings/display/ssd1307fb.txt @@ -27,6 +27,15 @@ Optional properties: - solomon,prechargep2: Length of precharge period (phase 2) in clock cycles. This needs to be the higher, the higher the capacitance of the OLED's pixels is + - solomon,dclk-div: Clock divisor 1 to 16 + - solomon,dclk-frq: Clock frequency 0 to 15, higher value means higher + frequency + - solomon,lookup-table: 8 bit value array of current drive pulse widths for + BANK0, and colors A, B, and C. Each value in range + of 31 to 63 for pulse widths of 32 to 64. Color D + is always width 64. + - solomon,area-color-enable: Display uses color mode + - solomon,low-power. Display runs in low power mode [0]: Documentation/devicetree/bindings/pwm/pwm.txt @@ -46,4 +55,5 @@ ssd1306: oled@3c { solomon,com-lrremap; solomon,com-invdir; solomon,com-offset = <32>; + solomon,lookup-table = /bits/ 8 <0x3f 0x3f 0x3f 0x3f>; }; diff --git a/Documentation/devicetree/bindings/display/st,stm32-ltdc.txt b/Documentation/devicetree/bindings/display/st,stm32-ltdc.txt index 3eb1b48b47dd..60c54da4e526 100644 --- a/Documentation/devicetree/bindings/display/st,stm32-ltdc.txt +++ b/Documentation/devicetree/bindings/display/st,stm32-ltdc.txt @@ -40,6 +40,8 @@ Mandatory nodes specific to STM32 DSI: - panel or bridge node: A node containing the panel or bridge description as documented in [6]. - port: panel or bridge port node, connected to the DSI output port (port@1). +Optional properties: +- phy-dsi-supply: phandle of the regulator that provides the supply voltage. Note: You can find more documentation in the following references [1] Documentation/devicetree/bindings/clock/clock-bindings.txt @@ -101,6 +103,7 @@ Example 2: DSI panel clock-names = "pclk", "ref"; resets = <&rcc STM32F4_APB2_RESET(DSI)>; reset-names = "apb"; + phy-dsi-supply = <®18>; ports { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt deleted file mode 100644 index 6a6cf5de08b0..000000000000 --- a/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt +++ /dev/null @@ -1,93 +0,0 @@ -Allwinner A31 DSI Encoder -========================= - -The DSI pipeline consists of two separate blocks: the DSI controller -itself, and its associated D-PHY. - -DSI Encoder ------------ - -The DSI Encoder generates the DSI signal from the TCON's. - -Required properties: - - compatible: value must be one of: - * allwinner,sun6i-a31-mipi-dsi - - reg: base address and size of memory-mapped region - - interrupts: interrupt associated to this IP - - clocks: phandles to the clocks feeding the DSI encoder - * bus: the DSI interface clock - * mod: the DSI module clock - - clock-names: the clock names mentioned above - - phys: phandle to the D-PHY - - phy-names: must be "dphy" - - resets: phandle to the reset controller driving the encoder - - - ports: A ports node with endpoint definitions as defined in - Documentation/devicetree/bindings/media/video-interfaces.txt. The - first port should be the input endpoint, usually coming from the - associated TCON. - -Any MIPI-DSI device attached to this should be described according to -the bindings defined in ../mipi-dsi-bus.txt - -D-PHY ------ - -Required properties: - - compatible: value must be one of: - * allwinner,sun6i-a31-mipi-dphy - - reg: base address and size of memory-mapped region - - clocks: phandles to the clocks feeding the DSI encoder - * bus: the DSI interface clock - * mod: the DSI module clock - - clock-names: the clock names mentioned above - - resets: phandle to the reset controller driving the encoder - -Example: - -dsi0: dsi@1ca0000 { - compatible = "allwinner,sun6i-a31-mipi-dsi"; - reg = <0x01ca0000 0x1000>; - interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ccu CLK_BUS_MIPI_DSI>, - <&ccu CLK_DSI_SCLK>; - clock-names = "bus", "mod"; - resets = <&ccu RST_BUS_MIPI_DSI>; - phys = <&dphy0>; - phy-names = "dphy"; - #address-cells = <1>; - #size-cells = <0>; - - panel@0 { - compatible = "bananapi,lhr050h41", "ilitek,ili9881c"; - reg = <0>; - power-gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; /* PB07 */ - reset-gpios = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL05 */ - backlight = <&pwm_bl>; - }; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - - dsi0_in_tcon0: endpoint { - remote-endpoint = <&tcon0_out_dsi0>; - }; - }; - }; -}; - -dphy0: d-phy@1ca1000 { - compatible = "allwinner,sun6i-a31-mipi-dphy"; - reg = <0x01ca1000 0x1000>; - clocks = <&ccu CLK_BUS_MIPI_DSI>, - <&ccu CLK_DSI_DPHY>; - clock-names = "bus", "mod"; - resets = <&ccu RST_BUS_MIPI_DSI>; - #phy-cells = <0>; -}; diff --git a/Documentation/devicetree/bindings/dma/8250_mtk_dma.txt b/Documentation/devicetree/bindings/dma/8250_mtk_dma.txt deleted file mode 100644 index 3fe0961bcf64..000000000000 --- a/Documentation/devicetree/bindings/dma/8250_mtk_dma.txt +++ /dev/null @@ -1,33 +0,0 @@ -* Mediatek UART APDMA Controller - -Required properties: -- compatible should contain: - * "mediatek,mt2712-uart-dma" for MT2712 compatible APDMA - * "mediatek,mt6577-uart-dma" for MT6577 and all of the above - -- reg: The base address of the APDMA register bank. - -- interrupts: A single interrupt specifier. - -- clocks : Must contain an entry for each entry in clock-names. - See ../clocks/clock-bindings.txt for details. -- clock-names: The APDMA clock for register accesses - -Examples: - - apdma: dma-controller@11000380 { - compatible = "mediatek,mt2712-uart-dma"; - reg = <0 0x11000380 0 0x400>; - interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_LOW>, - <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>, - <GIC_SPI 65 IRQ_TYPE_LEVEL_LOW>, - <GIC_SPI 66 IRQ_TYPE_LEVEL_LOW>, - <GIC_SPI 67 IRQ_TYPE_LEVEL_LOW>, - <GIC_SPI 68 IRQ_TYPE_LEVEL_LOW>, - <GIC_SPI 69 IRQ_TYPE_LEVEL_LOW>, - <GIC_SPI 70 IRQ_TYPE_LEVEL_LOW>; - clocks = <&pericfg CLK_PERI_AP_DMA>; - clock-names = "apdma"; - #dma-cells = <1>; - }; - diff --git a/Documentation/devicetree/bindings/dma/allwinner,sun4i-a10-dma.yaml b/Documentation/devicetree/bindings/dma/allwinner,sun4i-a10-dma.yaml new file mode 100644 index 000000000000..15abc0f9429f --- /dev/null +++ b/Documentation/devicetree/bindings/dma/allwinner,sun4i-a10-dma.yaml @@ -0,0 +1,55 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/dma/allwinner,sun4i-a10-dma.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 DMA Controller Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +allOf: + - $ref: "dma-controller.yaml#" + +properties: + "#dma-cells": + const: 2 + description: + The first cell is either 0 or 1, the former to use the normal + DMA, 1 for dedicated DMA. The second cell is the request line + number. + + compatible: + const: allwinner,sun4i-a10-dma + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + +required: + - "#dma-cells" + - compatible + - reg + - interrupts + - clocks + +additionalProperties: false + +examples: + - | + dma: dma-controller@1c02000 { + compatible = "allwinner,sun4i-a10-dma"; + reg = <0x01c02000 0x1000>; + interrupts = <27>; + clocks = <&ahb_gates 6>; + #dma-cells = <2>; + }; + +... diff --git a/Documentation/devicetree/bindings/dma/allwinner,sun50i-a64-dma.yaml b/Documentation/devicetree/bindings/dma/allwinner,sun50i-a64-dma.yaml new file mode 100644 index 000000000000..4cb9d6b93138 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/allwinner,sun50i-a64-dma.yaml @@ -0,0 +1,88 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/dma/allwinner,sun50i-a64-dma.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A64 DMA Controller Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +allOf: + - $ref: "dma-controller.yaml#" + +properties: + "#dma-cells": + const: 1 + description: The cell is the request line number. + + compatible: + enum: + - allwinner,sun50i-a64-dma + - allwinner,sun50i-h6-dma + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + items: + - const: bus + - const: mbus + + resets: + maxItems: 1 + +required: + - "#dma-cells" + - compatible + - reg + - interrupts + - clocks + - resets + - dma-channels + +if: + properties: + compatible: + const: allwinner,sun50i-h6-dma + +then: + properties: + clocks: + maxItems: 2 + + required: + - clock-names + +else: + properties: + clocks: + maxItems: 1 + +# FIXME: We should set it, but it would report all the generic +# properties as additional properties. +# additionalProperties: false + +examples: + - | + dma: dma-controller@1c02000 { + compatible = "allwinner,sun50i-a64-dma"; + reg = <0x01c02000 0x1000>; + interrupts = <0 50 4>; + clocks = <&ccu 30>; + dma-channels = <8>; + dma-requests = <27>; + resets = <&ccu 7>; + #dma-cells = <1>; + }; + +... diff --git a/Documentation/devicetree/bindings/dma/allwinner,sun6i-a31-dma.yaml b/Documentation/devicetree/bindings/dma/allwinner,sun6i-a31-dma.yaml new file mode 100644 index 000000000000..740b7f9b535b --- /dev/null +++ b/Documentation/devicetree/bindings/dma/allwinner,sun6i-a31-dma.yaml @@ -0,0 +1,62 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/dma/allwinner,sun6i-a31-dma.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A31 DMA Controller Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +allOf: + - $ref: "dma-controller.yaml#" + +properties: + "#dma-cells": + const: 1 + description: The cell is the request line number. + + compatible: + oneOf: + - const: allwinner,sun6i-a31-dma + - const: allwinner,sun8i-a23-dma + - const: allwinner,sun8i-a83t-dma + - const: allwinner,sun8i-h3-dma + - const: allwinner,sun8i-v3s-dma + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + +required: + - "#dma-cells" + - compatible + - reg + - interrupts + - clocks + - resets + +additionalProperties: false + +examples: + - | + dma: dma-controller@1c02000 { + compatible = "allwinner,sun6i-a31-dma"; + reg = <0x01c02000 0x1000>; + interrupts = <0 50 4>; + clocks = <&ahb1_gates 6>; + resets = <&ahb1_rst 6>; + #dma-cells = <1>; + }; + +... diff --git a/Documentation/devicetree/bindings/dma/arm-pl330.txt b/Documentation/devicetree/bindings/dma/arm-pl330.txt index db7e2260f9c5..2c7fd1941abb 100644 --- a/Documentation/devicetree/bindings/dma/arm-pl330.txt +++ b/Documentation/devicetree/bindings/dma/arm-pl330.txt @@ -16,6 +16,9 @@ Optional properties: - dma-channels: contains the total number of DMA channels supported by the DMAC - dma-requests: contains the total number of DMA requests supported by the DMAC - arm,pl330-broken-no-flushp: quirk for avoiding to execute DMAFLUSHP + - resets: contains an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: must contain at least "dma", and optional is "dma-ocp". Example: diff --git a/Documentation/devicetree/bindings/dma/dma-common.yaml b/Documentation/devicetree/bindings/dma/dma-common.yaml new file mode 100644 index 000000000000..ed0a49a6f020 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/dma-common.yaml @@ -0,0 +1,45 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/dma/dma-common.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: DMA Engine Generic Binding + +maintainers: + - Vinod Koul <vkoul@kernel.org> + +description: + Generic binding to provide a way for a driver using DMA Engine to + retrieve the DMA request or channel information that goes from a + hardware device to a DMA controller. + +select: false + +properties: + "#dma-cells": + minimum: 1 + # Should be enough + maximum: 255 + description: + Used to provide DMA controller specific information. + + dma-channel-mask: + $ref: /schemas/types.yaml#definitions/uint32 + description: + Bitmask of available DMA channels in ascending order that are + not reserved by firmware and are available to the + kernel. i.e. first channel corresponds to LSB. + + dma-channels: + $ref: /schemas/types.yaml#definitions/uint32 + description: + Number of DMA channels supported by the controller. + + dma-requests: + $ref: /schemas/types.yaml#definitions/uint32 + description: + Number of DMA request signals supported by the controller. + +required: + - "#dma-cells" diff --git a/Documentation/devicetree/bindings/dma/dma-controller.yaml b/Documentation/devicetree/bindings/dma/dma-controller.yaml new file mode 100644 index 000000000000..c39f6de76670 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/dma-controller.yaml @@ -0,0 +1,35 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/dma/dma-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: DMA Controller Generic Binding + +maintainers: + - Vinod Koul <vkoul@kernel.org> + +allOf: + - $ref: "dma-common.yaml#" + +# Everything else is described in the common file +properties: + $nodename: + pattern: "^dma-controller(@.*)?$" + +examples: + - | + dma: dma-controller@48000000 { + compatible = "ti,omap-sdma"; + reg = <0x48000000 0x1000>; + interrupts = <0 12 0x4 + 0 13 0x4 + 0 14 0x4 + 0 15 0x4>; + #dma-cells = <1>; + dma-channels = <32>; + dma-requests = <127>; + dma-channel-mask = <0xfffe>; + }; + +... diff --git a/Documentation/devicetree/bindings/dma/dma-router.yaml b/Documentation/devicetree/bindings/dma/dma-router.yaml new file mode 100644 index 000000000000..5b5f07393135 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/dma-router.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/dma/dma-router.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: DMA Router Generic Binding + +maintainers: + - Vinod Koul <vkoul@kernel.org> + +allOf: + - $ref: "dma-common.yaml#" + +description: + DMA routers are transparent IP blocks used to route DMA request + lines from devices to the DMA controller. Some SoCs (like TI DRA7x) + have more peripherals integrated with DMA requests than what the DMA + controller can handle directly. + +properties: + $nodename: + pattern: "^dma-router(@.*)?$" + + dma-masters: + $ref: /schemas/types.yaml#definitions/phandle-array + description: + Array of phandles to the DMA controllers the router can direct + the signal to. + + dma-requests: + description: + Number of incoming request lines the router can handle. + +required: + - "#dma-cells" + - dma-masters + +examples: + - | + sdma_xbar: dma-router@4a002b78 { + compatible = "ti,dra7-dma-crossbar"; + reg = <0x4a002b78 0xfc>; + #dma-cells = <1>; + dma-requests = <205>; + ti,dma-safe-map = <0>; + dma-masters = <&sdma>; + }; + +... diff --git a/Documentation/devicetree/bindings/dma/dma.txt b/Documentation/devicetree/bindings/dma/dma.txt index eeb4e4d1771e..90a67a016a48 100644 --- a/Documentation/devicetree/bindings/dma/dma.txt +++ b/Documentation/devicetree/bindings/dma/dma.txt @@ -1,113 +1 @@ -* Generic DMA Controller and DMA request bindings - -Generic binding to provide a way for a driver using DMA Engine to retrieve the -DMA request or channel information that goes from a hardware device to a DMA -controller. - - -* DMA controller - -Required property: -- #dma-cells: Must be at least 1. Used to provide DMA controller - specific information. See DMA client binding below for - more details. - -Optional properties: -- dma-channels: Number of DMA channels supported by the controller. -- dma-requests: Number of DMA request signals supported by the - controller. -- dma-channel-mask: Bitmask of available DMA channels in ascending order - that are not reserved by firmware and are available to - the kernel. i.e. first channel corresponds to LSB. - -Example: - - dma: dma@48000000 { - compatible = "ti,omap-sdma"; - reg = <0x48000000 0x1000>; - interrupts = <0 12 0x4 - 0 13 0x4 - 0 14 0x4 - 0 15 0x4>; - #dma-cells = <1>; - dma-channels = <32>; - dma-requests = <127>; - dma-channel-mask = <0xfffe> - }; - -* DMA router - -DMA routers are transparent IP blocks used to route DMA request lines from -devices to the DMA controller. Some SoCs (like TI DRA7x) have more peripherals -integrated with DMA requests than what the DMA controller can handle directly. - -Required property: -- dma-masters: phandle of the DMA controller or list of phandles for - the DMA controllers the router can direct the signal to. -- #dma-cells: Must be at least 1. Used to provide DMA router specific - information. See DMA client binding below for more - details. - -Optional properties: -- dma-requests: Number of incoming request lines the router can handle. -- In the node pointed by the dma-masters: - - dma-requests: The router driver might need to look for this in order - to configure the routing. - -Example: - sdma_xbar: dma-router@4a002b78 { - compatible = "ti,dra7-dma-crossbar"; - reg = <0x4a002b78 0xfc>; - #dma-cells = <1>; - dma-requests = <205>; - ti,dma-safe-map = <0>; - dma-masters = <&sdma>; - }; - -* DMA client - -Client drivers should specify the DMA property using a phandle to the controller -followed by DMA controller specific data. - -Required property: -- dmas: List of one or more DMA specifiers, each consisting of - - A phandle pointing to DMA controller node - - A number of integer cells, as determined by the - #dma-cells property in the node referenced by phandle - containing DMA controller specific information. This - typically contains a DMA request line number or a - channel number, but can contain any data that is - required for configuring a channel. -- dma-names: Contains one identifier string for each DMA specifier in - the dmas property. The specific strings that can be used - are defined in the binding of the DMA client device. - Multiple DMA specifiers can be used to represent - alternatives and in this case the dma-names for those - DMA specifiers must be identical (see examples). - -Examples: - -1. A device with one DMA read channel, one DMA write channel: - - i2c1: i2c@1 { - ... - dmas = <&dma 2 /* read channel */ - &dma 3>; /* write channel */ - dma-names = "rx", "tx"; - ... - }; - -2. A single read-write channel with three alternative DMA controllers: - - dmas = <&dma1 5 - &dma2 7 - &dma3 2>; - dma-names = "rx-tx", "rx-tx", "rx-tx"; - -3. A device with three channels, one of which has two alternatives: - - dmas = <&dma1 2 /* read channel */ - &dma1 3 /* write channel */ - &dma2 0 /* error read */ - &dma3 0>; /* alternative error read */ - dma-names = "rx", "tx", "error", "error"; +This file has been moved to dma-controller.yaml. diff --git a/Documentation/devicetree/bindings/dma/fsl-edma.txt b/Documentation/devicetree/bindings/dma/fsl-edma.txt index 97e213e07660..29dd3ccb1235 100644 --- a/Documentation/devicetree/bindings/dma/fsl-edma.txt +++ b/Documentation/devicetree/bindings/dma/fsl-edma.txt @@ -9,15 +9,16 @@ group, DMAMUX0 or DMAMUX1, but not both. Required properties: - compatible : - "fsl,vf610-edma" for eDMA used similar to that on Vybrid vf610 SoC + - "fsl,imx7ulp-edma" for eDMA2 used similar to that on i.mx7ulp - reg : Specifies base physical address(s) and size of the eDMA registers. The 1st region is eDMA control register's address and size. The 2nd and the 3rd regions are programmable channel multiplexing control register's address and size. - interrupts : A list of interrupt-specifiers, one for each entry in - interrupt-names. -- interrupt-names : Should contain: - "edma-tx" - the transmission interrupt - "edma-err" - the error interrupt + interrupt-names on vf610 similar SoC. But for i.mx7ulp per channel + per transmission interrupt, total 16 channel interrupt and 1 + error interrupt(located in the last), no interrupt-names list on + i.mx7ulp for clean on dts. - #dma-cells : Must be <2>. The 1st cell specifies the DMAMUX(0 for DMAMUX0 and 1 for DMAMUX1). Specific request source can only be multiplexed by specific channels @@ -28,6 +29,7 @@ Required properties: - clock-names : A list of channel group clock names. Should contain: "dmamux0" - clock name of mux0 group "dmamux1" - clock name of mux1 group + Note: No dmamux0 on i.mx7ulp, but another 'dma' clk added on i.mx7ulp. - clocks : A list of phandle and clock-specifier pairs, one for each entry in clock-names. @@ -35,6 +37,10 @@ Optional properties: - big-endian: If present registers and hardware scatter/gather descriptors of the eDMA are implemented in big endian mode, otherwise in little mode. +- interrupt-names : Should contain the below on vf610 similar SoC but not used + on i.mx7ulp similar SoC: + "edma-tx" - the transmission interrupt + "edma-err" - the error interrupt Examples: @@ -52,8 +58,36 @@ edma0: dma-controller@40018000 { clock-names = "dmamux0", "dmamux1"; clocks = <&clks VF610_CLK_DMAMUX0>, <&clks VF610_CLK_DMAMUX1>; -}; +}; /* vf610 */ +edma1: dma-controller@40080000 { + #dma-cells = <2>; + compatible = "fsl,imx7ulp-edma"; + reg = <0x40080000 0x2000>, + <0x40210000 0x1000>; + dma-channels = <32>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>, + /* last is eDMA2-ERR interrupt */ + <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "dma", "dmamux0"; + clocks = <&pcc2 IMX7ULP_CLK_DMA1>, + <&pcc2 IMX7ULP_CLK_DMA_MUX1>; +}; /* i.mx7ulp */ * DMA clients DMA client drivers that uses the DMA function must use the format described diff --git a/Documentation/devicetree/bindings/dma/fsl-qdma.txt b/Documentation/devicetree/bindings/dma/fsl-qdma.txt index 6a0ff9059e72..da371c4d406c 100644 --- a/Documentation/devicetree/bindings/dma/fsl-qdma.txt +++ b/Documentation/devicetree/bindings/dma/fsl-qdma.txt @@ -7,6 +7,7 @@ Required properties: - compatible: Must be one of "fsl,ls1021a-qdma": for LS1021A Board + "fsl,ls1028a-qdma": for LS1028A Board "fsl,ls1043a-qdma": for ls1043A Board "fsl,ls1046a-qdma": for ls1046A Board - reg: Should contain the register's base address and length. diff --git a/Documentation/devicetree/bindings/dma/mtk-uart-apdma.txt b/Documentation/devicetree/bindings/dma/mtk-uart-apdma.txt new file mode 100644 index 000000000000..5d6f98c43e3d --- /dev/null +++ b/Documentation/devicetree/bindings/dma/mtk-uart-apdma.txt @@ -0,0 +1,54 @@ +* Mediatek UART APDMA Controller + +Required properties: +- compatible should contain: + * "mediatek,mt2712-uart-dma" for MT2712 compatible APDMA + * "mediatek,mt6577-uart-dma" for MT6577 and all of the above + +- reg: The base address of the APDMA register bank. + +- interrupts: A single interrupt specifier. + One interrupt per dma-requests, or 8 if no dma-requests property is present + +- dma-requests: The number of DMA channels + +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: The APDMA clock for register accesses + +- mediatek,dma-33bits: Present if the DMA requires support + +Examples: + + apdma: dma-controller@11000400 { + compatible = "mediatek,mt2712-uart-dma"; + reg = <0 0x11000400 0 0x80>, + <0 0x11000480 0 0x80>, + <0 0x11000500 0 0x80>, + <0 0x11000580 0 0x80>, + <0 0x11000600 0 0x80>, + <0 0x11000680 0 0x80>, + <0 0x11000700 0 0x80>, + <0 0x11000780 0 0x80>, + <0 0x11000800 0 0x80>, + <0 0x11000880 0 0x80>, + <0 0x11000900 0 0x80>, + <0 0x11000980 0 0x80>; + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 105 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 106 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 107 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 108 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 109 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 110 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 111 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 112 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 113 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 114 IRQ_TYPE_LEVEL_LOW>; + dma-requests = <12>; + clocks = <&pericfg CLK_PERI_AP_DMA>; + clock-names = "apdma"; + mediatek,dma-33bits; + #dma-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/dma/nbpfaxi.txt b/Documentation/devicetree/bindings/dma/renesas,nbpfaxi.txt index d2e1e62e346a..d2e1e62e346a 100644 --- a/Documentation/devicetree/bindings/dma/nbpfaxi.txt +++ b/Documentation/devicetree/bindings/dma/renesas,nbpfaxi.txt diff --git a/Documentation/devicetree/bindings/dma/shdma.txt b/Documentation/devicetree/bindings/dma/renesas,shdma.txt index a91920a49433..a91920a49433 100644 --- a/Documentation/devicetree/bindings/dma/shdma.txt +++ b/Documentation/devicetree/bindings/dma/renesas,shdma.txt diff --git a/Documentation/devicetree/bindings/dma/sun4i-dma.txt b/Documentation/devicetree/bindings/dma/sun4i-dma.txt deleted file mode 100644 index 8ad556aca70b..000000000000 --- a/Documentation/devicetree/bindings/dma/sun4i-dma.txt +++ /dev/null @@ -1,45 +0,0 @@ -Allwinner A10 DMA Controller - -This driver follows the generic DMA bindings defined in dma.txt. - -Required properties: - -- compatible: Must be "allwinner,sun4i-a10-dma" -- reg: Should contain the registers base address and length -- interrupts: Should contain a reference to the interrupt used by this device -- clocks: Should contain a reference to the parent AHB clock -- #dma-cells : Should be 2, first cell denoting normal or dedicated dma, - second cell holding the request line number. - -Example: - dma: dma-controller@1c02000 { - compatible = "allwinner,sun4i-a10-dma"; - reg = <0x01c02000 0x1000>; - interrupts = <27>; - clocks = <&ahb_gates 6>; - #dma-cells = <2>; - }; - -Clients: - -DMA clients connected to the Allwinner A10 DMA controller must use the -format described in the dma.txt file, using a three-cell specifier for -each channel: a phandle plus two integer cells. -The three cells in order are: - -1. A phandle pointing to the DMA controller. -2. Whether it is using normal (0) or dedicated (1) channels -3. The port ID as specified in the datasheet - -Example: - spi2: spi@1c17000 { - compatible = "allwinner,sun4i-a10-spi"; - reg = <0x01c17000 0x1000>; - interrupts = <0 12 4>; - clocks = <&ahb_gates 22>, <&spi2_clk>; - clock-names = "ahb", "mod"; - dmas = <&dma 1 29>, <&dma 1 28>; - dma-names = "rx", "tx"; - #address-cells = <1>; - #size-cells = <0>; - }; diff --git a/Documentation/devicetree/bindings/dma/sun6i-dma.txt b/Documentation/devicetree/bindings/dma/sun6i-dma.txt deleted file mode 100644 index 7fccc20d8331..000000000000 --- a/Documentation/devicetree/bindings/dma/sun6i-dma.txt +++ /dev/null @@ -1,76 +0,0 @@ -Allwinner A31 DMA Controller - -This driver follows the generic DMA bindings defined in dma.txt. - -Required properties: - -- compatible: Must be one of - "allwinner,sun6i-a31-dma" - "allwinner,sun8i-a23-dma" - "allwinner,sun8i-a83t-dma" - "allwinner,sun8i-h3-dma" - "allwinner,sun8i-v3s-dma" -- reg: Should contain the registers base address and length -- interrupts: Should contain a reference to the interrupt used by this device -- clocks: Should contain a reference to the parent AHB clock -- resets: Should contain a reference to the reset controller asserting - this device in reset -- #dma-cells : Should be 1, a single cell holding a line request number - -Example: - dma: dma-controller@1c02000 { - compatible = "allwinner,sun6i-a31-dma"; - reg = <0x01c02000 0x1000>; - interrupts = <0 50 4>; - clocks = <&ahb1_gates 6>; - resets = <&ahb1_rst 6>; - #dma-cells = <1>; - }; - ------------------------------------------------------------------------------- -For A64 DMA controller: - -Required properties: -- compatible: "allwinner,sun50i-a64-dma" -- dma-channels: Number of DMA channels supported by the controller. - Refer to Documentation/devicetree/bindings/dma/dma.txt -- all properties above, i.e. reg, interrupts, clocks, resets and #dma-cells - -Optional properties: -- dma-requests: Number of DMA request signals supported by the controller. - Refer to Documentation/devicetree/bindings/dma/dma.txt - -Example: - dma: dma-controller@1c02000 { - compatible = "allwinner,sun50i-a64-dma"; - reg = <0x01c02000 0x1000>; - interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ccu CLK_BUS_DMA>; - dma-channels = <8>; - dma-requests = <27>; - resets = <&ccu RST_BUS_DMA>; - #dma-cells = <1>; - }; ------------------------------------------------------------------------------- - -Clients: - -DMA clients connected to the A31 DMA controller must use the format -described in the dma.txt file, using a two-cell specifier for each -channel: a phandle plus one integer cells. -The two cells in order are: - -1. A phandle pointing to the DMA controller. -2. The port ID as specified in the datasheet - -Example: -spi2: spi@1c6a000 { - compatible = "allwinner,sun6i-a31-spi"; - reg = <0x01c6a000 0x1000>; - interrupts = <0 67 4>; - clocks = <&ahb1_gates 22>, <&spi2_clk>; - clock-names = "ahb", "mod"; - dmas = <&dma 25>, <&dma 25>; - dma-names = "rx", "tx"; - resets = <&ahb1_rst 22>; -}; diff --git a/Documentation/devicetree/bindings/dsp/fsl,dsp.yaml b/Documentation/devicetree/bindings/dsp/fsl,dsp.yaml new file mode 100644 index 000000000000..3248595dc93c --- /dev/null +++ b/Documentation/devicetree/bindings/dsp/fsl,dsp.yaml @@ -0,0 +1,88 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/dsp/fsl,dsp.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP i.MX8 DSP core + +maintainers: + - Daniel Baluta <daniel.baluta@nxp.com> + +description: | + Some boards from i.MX8 family contain a DSP core used for + advanced pre- and post- audio processing. + +properties: + compatible: + enum: + - fsl,imx8qxp-dsp + + reg: + description: Should contain register location and length + + clocks: + items: + - description: ipg clock + - description: ocram clock + - description: core clock + + clock-names: + items: + - const: ipg + - const: ocram + - const: core + + power-domains: + description: + List of phandle and PM domain specifier as documented in + Documentation/devicetree/bindings/power/power_domain.txt + maxItems: 4 + + mboxes: + description: + List of <&phandle type channel> - 2 channels for TXDB, 2 channels for RXDB + (see mailbox/fsl,mu.txt) + maxItems: 4 + + mbox-names: + items: + - const: txdb0 + - const: txdb1 + - const: rxdb0 + - const: rxdb1 + + memory-region: + description: + phandle to a node describing reserved memory (System RAM memory) + used by DSP (see bindings/reserved-memory/reserved-memory.txt) + maxItems: 1 + +required: + - compatible + - reg + - clocks + - clock-names + - power-domains + - mboxes + - mbox-names + - memory-region + +examples: + - | + #include <dt-bindings/firmware/imx/rsrc.h> + #include <dt-bindings/clock/imx8-clock.h> + dsp@596e8000 { + compatible = "fsl,imx8qxp-dsp"; + reg = <0x596e8000 0x88000>; + clocks = <&adma_lpcg IMX_ADMA_LPCG_DSP_IPG_CLK>, + <&adma_lpcg IMX_ADMA_LPCG_OCRAM_IPG_CLK>, + <&adma_lpcg IMX_ADMA_LPCG_DSP_CORE_CLK>; + clock-names = "ipg", "ocram", "core"; + power-domains = <&pd IMX_SC_R_MU_13A>, + <&pd IMX_SC_R_MU_13B>, + <&pd IMX_SC_R_DSP>, + <&pd IMX_SC_R_DSP_RAM>; + mbox-names = "txdb0", "txdb1", "rxdb0", "rxdb1"; + mboxes = <&lsio_mu13 2 0>, <&lsio_mu13 2 1>, <&lsio_mu13 3 0>, <&lsio_mu13 3 1>; + }; diff --git a/Documentation/devicetree/bindings/eeprom/at25.txt b/Documentation/devicetree/bindings/eeprom/at25.txt index b3bde97dc199..42577dd113dd 100644 --- a/Documentation/devicetree/bindings/eeprom/at25.txt +++ b/Documentation/devicetree/bindings/eeprom/at25.txt @@ -3,6 +3,7 @@ EEPROMs (SPI) compatible with Atmel at25. Required properties: - compatible : Should be "<vendor>,<type>", and generic value "atmel,at25". Example "<vendor>,<type>" values: + "anvo,anv32e61w" "microchip,25lc040" "st,m95m02" "st,m95256" diff --git a/Documentation/devicetree/bindings/example-schema.yaml b/Documentation/devicetree/bindings/example-schema.yaml index 9175d67f355d..c43819c2783a 100644 --- a/Documentation/devicetree/bindings/example-schema.yaml +++ b/Documentation/devicetree/bindings/example-schema.yaml @@ -5,7 +5,7 @@ # All the top-level keys are standard json-schema keywords except for # 'maintainers' and 'select' -# $id is a unique idenifier based on the filename. There may or may not be a +# $id is a unique identifier based on the filename. There may or may not be a # file present at the URL. $id: "http://devicetree.org/schemas/example-schema.yaml#" # $schema is the meta-schema this schema should be validated with. diff --git a/Documentation/devicetree/bindings/extcon/extcon-arizona.txt b/Documentation/devicetree/bindings/extcon/extcon-arizona.txt index 7f3d94ae81ff..208daaff0be4 100644 --- a/Documentation/devicetree/bindings/extcon/extcon-arizona.txt +++ b/Documentation/devicetree/bindings/extcon/extcon-arizona.txt @@ -72,5 +72,5 @@ codec: wm8280@0 { 1 2 1 /* MICDET2 MICBIAS2 GPIO=high */ >; - wlf,gpsw = <0>; + wlf,gpsw = <ARIZONA_GPSW_OPEN>; }; diff --git a/Documentation/devicetree/bindings/extcon/extcon-fsa9480.txt b/Documentation/devicetree/bindings/extcon/extcon-fsa9480.txt new file mode 100644 index 000000000000..624bd76f468e --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/extcon-fsa9480.txt @@ -0,0 +1,21 @@ +FAIRCHILD SEMICONDUCTOR FSA9480 MICROUSB SWITCH + +The FSA9480 is a USB port accessory detector and switch. The FSA9480 is fully +controlled using I2C and enables USB data, stereo and mono audio, video, +microphone, and UART data to use a common connector port. + +Required properties: + - compatible : Must be one of + "fcs,fsa9480" + "fcs,fsa880" + - reg : Specifies i2c slave address. Must be 0x25. + - interrupts : Should contain one entry specifying interrupt signal of + interrupt parent to which interrupt pin of the chip is connected. + + Example: + musb@25 { + compatible = "fcs,fsa9480"; + reg = <0x25>; + interrupt-parent = <&gph2>; + interrupts = <7 0>; + }; diff --git a/Documentation/devicetree/bindings/fieldbus/arcx,anybus-controller.txt b/Documentation/devicetree/bindings/fieldbus/arcx,anybus-controller.txt deleted file mode 100644 index b1f9474f36d5..000000000000 --- a/Documentation/devicetree/bindings/fieldbus/arcx,anybus-controller.txt +++ /dev/null @@ -1,71 +0,0 @@ -* Arcx Anybus-S controller - -This chip communicates with the SoC over a parallel bus. It is -expected that its Device Tree node is specified as the child of a node -corresponding to the parallel bus used for communication. - -Required properties: --------------------- - - - compatible : The following chip-specific string: - "arcx,anybus-controller" - - - reg : three areas: - index 0: bus memory area where the cpld registers are located. - index 1: bus memory area of the first host's dual-port ram. - index 2: bus memory area of the second host's dual-port ram. - - - reset-gpios : the GPIO pin connected to the reset line of the controller. - - - interrupts : two interrupts: - index 0: interrupt connected to the first host - index 1: interrupt connected to the second host - Generic interrupt client node bindings are described in - interrupt-controller/interrupts.txt - -Optional: use of subnodes -------------------------- - -The card connected to a host may need additional properties. These can be -specified in subnodes to the controller node. - -The subnodes are identified by the standard 'reg' property. Which information -exactly can be specified depends on the bindings for the function driver -for the subnode. - -Required controller node properties when using subnodes: -- #address-cells: should be one. -- #size-cells: should be zero. - -Required subnode properties: -- reg: Must contain the host index of the card this subnode describes: - <0> for the first host on the controller - <1> for the second host on the controller - Note that only a single card can be plugged into a host, so the host - index uniquely describes the card location. - -Example of usage: ------------------ - -This example places the bridge on top of the i.MX WEIM parallel bus, see: -Documentation/devicetree/bindings/bus/imx-weim.txt - -&weim { - controller@0,0 { - compatible = "arcx,anybus-controller"; - reg = <0 0 0x100>, <0 0x400000 0x800>, <1 0x400000 0x800>; - reset-gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>; - interrupt-parent = <&gpio1>; - interrupts = <1 IRQ_TYPE_LEVEL_LOW>, <5 IRQ_TYPE_LEVEL_LOW>; - /* fsl,weim-cs-timing is a i.MX WEIM bus specific property */ - fsl,weim-cs-timing = <0x024400b1 0x00001010 0x20081100 - 0x00000000 0xa0000240 0x00000000>; - /* optional subnode for a card plugged into the first host */ - #address-cells = <1>; - #size-cells = <0>; - card@0 { - reg = <0>; - /* card specific properties go here */ - }; - }; -}; diff --git a/Documentation/devicetree/bindings/firmware/cznic,turris-mox-rwtm.txt b/Documentation/devicetree/bindings/firmware/cznic,turris-mox-rwtm.txt new file mode 100644 index 000000000000..338169dea7bb --- /dev/null +++ b/Documentation/devicetree/bindings/firmware/cznic,turris-mox-rwtm.txt @@ -0,0 +1,19 @@ +Turris Mox rWTM firmware driver + +Required properties: + - compatible : Should be "cznic,turris-mox-rwtm" + - mboxes : Must contain a reference to associated mailbox + +This device tree node should be used on Turris Mox, or potentially another A3700 +compatible device running the Mox's rWTM firmware in the secure processor (for +example it is possible to flash this firmware into EspressoBin). + +Example: + + firmware { + turris-mox-rwtm { + compatible = "cznic,turris-mox-rwtm"; + mboxes = <&rwtm 0>; + status = "okay"; + }; + }; diff --git a/Documentation/devicetree/bindings/firmware/intel,ixp4xx-network-processing-engine.yaml b/Documentation/devicetree/bindings/firmware/intel,ixp4xx-network-processing-engine.yaml index 8cb136c376fb..4f0db8ee226a 100644 --- a/Documentation/devicetree/bindings/firmware/intel,ixp4xx-network-processing-engine.yaml +++ b/Documentation/devicetree/bindings/firmware/intel,ixp4xx-network-processing-engine.yaml @@ -2,7 +2,7 @@ # Copyright 2019 Linaro Ltd. %YAML 1.2 --- -$id: "http://devicetree.org/schemas/firmware/intel-ixp4xx-network-processing-engine.yaml#" +$id: "http://devicetree.org/schemas/firmware/intel,ixp4xx-network-processing-engine.yaml#" $schema: "http://devicetree.org/meta-schemas/core.yaml#" title: Intel IXP4xx Network Processing Engine diff --git a/Documentation/devicetree/bindings/firmware/qcom,scm.txt b/Documentation/devicetree/bindings/firmware/qcom,scm.txt index 41f133a4e2fa..3f29ea04b5fe 100644 --- a/Documentation/devicetree/bindings/firmware/qcom,scm.txt +++ b/Documentation/devicetree/bindings/firmware/qcom,scm.txt @@ -9,14 +9,16 @@ Required properties: - compatible: must contain one of the following: * "qcom,scm-apq8064" * "qcom,scm-apq8084" + * "qcom,scm-ipq4019" * "qcom,scm-msm8660" * "qcom,scm-msm8916" * "qcom,scm-msm8960" * "qcom,scm-msm8974" * "qcom,scm-msm8996" * "qcom,scm-msm8998" - * "qcom,scm-ipq4019" + * "qcom,scm-sc7180" * "qcom,scm-sdm845" + * "qcom,scm-sm8150" and: * "qcom,scm" - clocks: Specifies clocks needed by the SCM interface, if any: diff --git a/Documentation/devicetree/bindings/fpga/altera-fpga2sdram-bridge.txt b/Documentation/devicetree/bindings/fpga/altera-fpga2sdram-bridge.txt index 817a8d4bf903..5dd0ff0f7b4e 100644 --- a/Documentation/devicetree/bindings/fpga/altera-fpga2sdram-bridge.txt +++ b/Documentation/devicetree/bindings/fpga/altera-fpga2sdram-bridge.txt @@ -3,10 +3,7 @@ Altera FPGA To SDRAM Bridge Driver Required properties: - compatible : Should contain "altr,socfpga-fpga2sdram-bridge" -Optional properties: -- bridge-enable : 0 if driver should disable bridge at startup - 1 if driver should enable bridge at startup - Default is to leave bridge in current state. +See Documentation/devicetree/bindings/fpga/fpga-bridge.txt for generic bindings. Example: fpga_bridge3: fpga-bridge@ffc25080 { diff --git a/Documentation/devicetree/bindings/fpga/altera-freeze-bridge.txt b/Documentation/devicetree/bindings/fpga/altera-freeze-bridge.txt index f8e288c71b2d..8b26fbcff3c6 100644 --- a/Documentation/devicetree/bindings/fpga/altera-freeze-bridge.txt +++ b/Documentation/devicetree/bindings/fpga/altera-freeze-bridge.txt @@ -10,10 +10,7 @@ Required properties: - compatible : Should contain "altr,freeze-bridge-controller" - regs : base address and size for freeze bridge module -Optional properties: -- bridge-enable : 0 if driver should disable bridge at startup - 1 if driver should enable bridge at startup - Default is to leave bridge in current state. +See Documentation/devicetree/bindings/fpga/fpga-bridge.txt for generic bindings. Example: freeze-controller@100000450 { diff --git a/Documentation/devicetree/bindings/fpga/altera-hps2fpga-bridge.txt b/Documentation/devicetree/bindings/fpga/altera-hps2fpga-bridge.txt index 6406f9337eeb..68cce3945b10 100644 --- a/Documentation/devicetree/bindings/fpga/altera-hps2fpga-bridge.txt +++ b/Documentation/devicetree/bindings/fpga/altera-hps2fpga-bridge.txt @@ -9,10 +9,7 @@ Required properties: - resets : Phandle and reset specifier for this bridge's reset - clocks : Clocks used by this module. -Optional properties: -- bridge-enable : 0 if driver should disable bridge at startup. - 1 if driver should enable bridge at startup. - Default is to leave bridge in its current state. +See Documentation/devicetree/bindings/fpga/fpga-bridge.txt for generic bindings. Example: fpga_bridge0: fpga-bridge@ff400000 { diff --git a/Documentation/devicetree/bindings/fpga/fpga-bridge.txt b/Documentation/devicetree/bindings/fpga/fpga-bridge.txt new file mode 100644 index 000000000000..72e06917288a --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/fpga-bridge.txt @@ -0,0 +1,13 @@ +FPGA Bridge Device Tree Binding + +Optional properties: +- bridge-enable : 0 if driver should disable bridge at startup + 1 if driver should enable bridge at startup + Default is to leave bridge in current state. + +Example: + fpga_bridge3: fpga-bridge@ffc25080 { + compatible = "altr,socfpga-fpga2sdram-bridge"; + reg = <0xffc25080 0x4>; + bridge-enable = <0>; + }; diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt index 8dcfba926bc7..4284d293fa61 100644 --- a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt @@ -18,12 +18,8 @@ Required properties: - clocks : input clock to IP - clock-names : should contain "aclk" -Optional properties: -- bridge-enable : 0 if driver should disable bridge at startup - 1 if driver should enable bridge at startup - Default is to leave bridge in current state. - -See Documentation/devicetree/bindings/fpga/fpga-region.txt for generic bindings. +See Documentation/devicetree/bindings/fpga/fpga-region.txt and +Documentation/devicetree/bindings/fpga/fpga-bridge.txt for generic bindings. Example: fpga-bridge@100000450 { diff --git a/Documentation/devicetree/bindings/gpio/gpio-aspeed.txt b/Documentation/devicetree/bindings/gpio/gpio-aspeed.txt index 7e9b586770b0..b2033fc3a71a 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-aspeed.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-aspeed.txt @@ -2,7 +2,8 @@ Aspeed GPIO controller Device Tree Bindings ------------------------------------------- Required properties: -- compatible : Either "aspeed,ast2400-gpio" or "aspeed,ast2500-gpio" +- compatible : Either "aspeed,ast2400-gpio", "aspeed,ast2500-gpio", + or "aspeed,ast2600-gpio". - #gpio-cells : Should be two - First cell is the GPIO line number @@ -17,7 +18,9 @@ Required properties: Optional properties: -- clocks : A phandle to the clock to use for debounce timings +- clocks : A phandle to the clock to use for debounce timings +- ngpios : Number of GPIOs controlled by this controller. Should be set + when there are multiple GPIO controllers on a SoC (ast2600). The gpio and interrupt properties are further described in their respective bindings documentation: diff --git a/Documentation/devicetree/bindings/gpio/gpio-davinci.txt b/Documentation/devicetree/bindings/gpio/gpio-davinci.txt index 553b92a7e87b..cd91d61eac31 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-davinci.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-davinci.txt @@ -5,6 +5,8 @@ Required Properties: "ti,keystone-gpio": for Keystone 2 66AK2H/K, 66AK2L, 66AK2E SoCs "ti,k2g-gpio", "ti,keystone-gpio": for 66AK2G + "ti,am654-gpio", "ti,keystone-gpio": for TI K3 AM654 + "ti,j721e-gpio", "ti,keystone-gpio": for J721E SoCs - reg: Physical base address of the controller and the size of memory mapped registers. @@ -145,3 +147,20 @@ gpio0: gpio@260bf00 { ti,ngpio = <32>; ti,davinci-gpio-unbanked = <32>; }; + +Example for K3 AM654: + +wkup_gpio0: wkup_gpio0@42110000 { + compatible = "ti,am654-gpio", "ti,keystone-gpio"; + reg = <0x42110000 0x100>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&intr_wkup_gpio>; + interrupts = <59 128>, <59 129>, <59 130>, <59 131>; + interrupt-controller; + #interrupt-cells = <2>; + ti,ngpio = <56>; + ti,davinci-gpio-unbanked = <0>; + clocks = <&k3_clks 59 0>; + clock-names = "gpio"; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-moxtet.txt b/Documentation/devicetree/bindings/gpio/gpio-moxtet.txt new file mode 100644 index 000000000000..410759de9f09 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-moxtet.txt @@ -0,0 +1,18 @@ +Turris Mox Moxtet GPIO expander via Moxtet bus + +Required properties: + - compatible : Should be "cznic,moxtet-gpio". + - gpio-controller : Marks the device node as a GPIO controller. + - #gpio-cells : Should be two. For consumer use see gpio.txt. + +Other properties are required for a Moxtet bus device, please refer to +Documentation/devicetree/bindings/bus/moxtet.txt. + +Example: + + moxtet_sfp: gpio@0 { + compatible = "cznic,moxtet-gpio"; + gpio-controller; + #gpio-cells = <2>; + reg = <0>; + } diff --git a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt index 69d46162d0f5..cd28e932bf50 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt @@ -4,7 +4,7 @@ Required properties: - compatible : Should be "fsl,<soc>-gpio" The following <soc>s are known to be supported: mpc5121, mpc5125, mpc8349, mpc8572, mpc8610, pq3, qoriq, - ls1021a, ls1043a, ls2080a. + ls1021a, ls1043a, ls2080a, ls1028a, ls1088a. - reg : Address and length of the register set for the device - interrupts : Should be the port interrupt shared by all 32 pins. - #gpio-cells : Should be two. The first cell is the pin number and @@ -37,3 +37,17 @@ gpio0: gpio@2300000 { interrupt-controller; #interrupt-cells = <2>; }; + + +Example of gpio-controller node for a ls1028a/ls1088a SoC: + +gpio1: gpio@2300000 { + compatible = "fsl,ls1028a-gpio", "fsl,ls1088a-gpio", "fsl,qoriq-gpio"; + reg = <0x0 0x2300000 0x0 0x10000>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + little-endian; +}; diff --git a/Documentation/devicetree/bindings/gpio/pl061-gpio.txt b/Documentation/devicetree/bindings/gpio/pl061-gpio.txt deleted file mode 100644 index 89058d375b7c..000000000000 --- a/Documentation/devicetree/bindings/gpio/pl061-gpio.txt +++ /dev/null @@ -1,10 +0,0 @@ -ARM PL061 GPIO controller - -Required properties: -- compatible : "arm,pl061", "arm,primecell" -- #gpio-cells : Should be two. The first cell is the pin number and the - second cell is used to specify optional parameters: - - bit 0 specifies polarity (0 for normal, 1 for inverted) -- gpio-controller : Marks the device node as a GPIO controller. -- interrupts : Interrupt mapping for GPIO IRQ. -- gpio-ranges : Interaction with the PINCTRL subsystem. diff --git a/Documentation/devicetree/bindings/gpio/pl061-gpio.yaml b/Documentation/devicetree/bindings/gpio/pl061-gpio.yaml new file mode 100644 index 000000000000..313b17229247 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/pl061-gpio.yaml @@ -0,0 +1,69 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/pl061-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM PL061 GPIO controller + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + - Rob Herring <robh@kernel.org> + +# We need a select here so we don't match all nodes with 'arm,primecell' +select: + properties: + compatible: + contains: + const: arm,pl061 + required: + - compatible + +properties: + $nodename: + pattern: "^gpio@[0-9a-f]+$" + + compatible: + items: + - const: arm,pl061 + - const: arm,primecell + + reg: + maxItems: 1 + + interrupts: + oneOf: + - maxItems: 1 + - maxItems: 8 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + clocks: + maxItems: 1 + + clock-names: true + + "#gpio-cells": + const: 2 + + gpio-controller: true + + gpio-ranges: + maxItems: 8 + +required: + - compatible + - reg + - interrupts + - interrupt-controller + - "#interrupt-cells" + - clocks + - "#gpio-cells" + - gpio-controller + +additionalProperties: false + +... diff --git a/Documentation/devicetree/bindings/gpio/sgpio-aspeed.txt b/Documentation/devicetree/bindings/gpio/sgpio-aspeed.txt new file mode 100644 index 000000000000..d4d83916c09d --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/sgpio-aspeed.txt @@ -0,0 +1,45 @@ +Aspeed SGPIO controller Device Tree Bindings +-------------------------------------------- + +This SGPIO controller is for ASPEED AST2500 SoC, it supports up to 80 full +featured Serial GPIOs. Each of the Serial GPIO pins can be programmed to +support the following options: +- Support interrupt option for each input port and various interrupt + sensitivity option (level-high, level-low, edge-high, edge-low) +- Support reset tolerance option for each output port +- Directly connected to APB bus and its shift clock is from APB bus clock + divided by a programmable value. +- Co-work with external signal-chained TTL components (74LV165/74LV595) + +Required properties: + +- compatible : Should be one of + "aspeed,ast2400-sgpio", "aspeed,ast2500-sgpio" +- #gpio-cells : Should be 2, see gpio.txt +- reg : Address and length of the register set for the device +- gpio-controller : Marks the device node as a GPIO controller +- interrupts : Interrupt specifier, see interrupt-controller/interrupts.txt +- interrupt-controller : Mark the GPIO controller as an interrupt-controller +- ngpios : number of GPIO lines, see gpio.txt + (should be multiple of 8, up to 80 pins) +- clocks : A phandle to the APB clock for SGPM clock division +- bus-frequency : SGPM CLK frequency + +The sgpio and interrupt properties are further described in their respective +bindings documentation: + +- Documentation/devicetree/bindings/gpio/gpio.txt +- Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + + Example: + sgpio: sgpio@1e780200 { + #gpio-cells = <2>; + compatible = "aspeed,ast2500-sgpio"; + gpio-controller; + interrupts = <40>; + reg = <0x1e780200 0x0100>; + clocks = <&syscon ASPEED_CLK_APB>; + interrupt-controller; + ngpios = <8>; + bus-frequency = <12000000>; + }; diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-bifrost.txt b/Documentation/devicetree/bindings/gpu/arm,mali-bifrost.txt deleted file mode 100644 index b8be9dbc68b4..000000000000 --- a/Documentation/devicetree/bindings/gpu/arm,mali-bifrost.txt +++ /dev/null @@ -1,92 +0,0 @@ -ARM Mali Bifrost GPU -==================== - -Required properties: - -- compatible : - * Since Mali Bifrost GPU model/revision is fully discoverable by reading - some determined registers, must contain the following: - + "arm,mali-bifrost" - * which must be preceded by one of the following vendor specifics: - + "amlogic,meson-g12a-mali" - -- reg : Physical base address of the device and length of the register area. - -- interrupts : Contains the three IRQ lines required by Mali Bifrost devices, - in the following defined order. - -- interrupt-names : Contains the names of IRQ resources in this exact defined - order: "job", "mmu", "gpu". - -Optional properties: - -- clocks : Phandle to clock for the Mali Bifrost device. - -- mali-supply : Phandle to regulator for the Mali device. Refer to - Documentation/devicetree/bindings/regulator/regulator.txt for details. - -- operating-points-v2 : Refer to Documentation/devicetree/bindings/opp/opp.txt - for details. - -- resets : Phandle of the GPU reset line. - -Vendor-specific bindings ------------------------- - -The Mali GPU is integrated very differently from one SoC to -another. In order to accommodate those differences, you have the option -to specify one more vendor-specific compatible, among: - -- "amlogic,meson-g12a-mali" - Required properties: - - resets : Should contain phandles of : - + GPU reset line - + GPU APB glue reset line - -Example for a Mali-G31: - -gpu@ffa30000 { - compatible = "amlogic,meson-g12a-mali", "arm,mali-bifrost"; - reg = <0xffe40000 0x10000>; - interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "job", "mmu", "gpu"; - clocks = <&clk CLKID_MALI>; - mali-supply = <&vdd_gpu>; - operating-points-v2 = <&gpu_opp_table>; - resets = <&reset RESET_DVALIN_CAPB3>, <&reset RESET_DVALIN>; -}; - -gpu_opp_table: opp_table0 { - compatible = "operating-points-v2"; - - opp@533000000 { - opp-hz = /bits/ 64 <533000000>; - opp-microvolt = <1250000>; - }; - opp@450000000 { - opp-hz = /bits/ 64 <450000000>; - opp-microvolt = <1150000>; - }; - opp@400000000 { - opp-hz = /bits/ 64 <400000000>; - opp-microvolt = <1125000>; - }; - opp@350000000 { - opp-hz = /bits/ 64 <350000000>; - opp-microvolt = <1075000>; - }; - opp@266000000 { - opp-hz = /bits/ 64 <266000000>; - opp-microvolt = <1025000>; - }; - opp@160000000 { - opp-hz = /bits/ 64 <160000000>; - opp-microvolt = <925000>; - }; - opp@100000000 { - opp-hz = /bits/ 64 <100000000>; - opp-microvolt = <912500>; - }; -}; diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-bifrost.yaml b/Documentation/devicetree/bindings/gpu/arm,mali-bifrost.yaml new file mode 100644 index 000000000000..5f1fd6d7ee0f --- /dev/null +++ b/Documentation/devicetree/bindings/gpu/arm,mali-bifrost.yaml @@ -0,0 +1,116 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpu/arm,mali-bifrost.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM Mali Bifrost GPU + +maintainers: + - Rob Herring <robh@kernel.org> + +properties: + $nodename: + pattern: '^gpu@[a-f0-9]+$' + + compatible: + items: + - enum: + - amlogic,meson-g12a-mali + - const: arm,mali-bifrost # Mali Bifrost GPU model/revision is fully discoverable + + reg: + maxItems: 1 + + interrupts: + items: + - description: Job interrupt + - description: MMU interrupt + - description: GPU interrupt + + interrupt-names: + items: + - const: job + - const: mmu + - const: gpu + + clocks: + maxItems: 1 + + mali-supply: + maxItems: 1 + + operating-points-v2: true + +required: + - compatible + - reg + - interrupts + - interrupt-names + - clocks + +allOf: + - if: + properties: + compatible: + contains: + const: amlogic,meson-g12a-mali + then: + properties: + resets: + minItems: 2 + required: + - resets + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + gpu@ffe40000 { + compatible = "amlogic,meson-g12a-mali", "arm,mali-bifrost"; + reg = <0xffe40000 0x10000>; + interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "job", "mmu", "gpu"; + clocks = <&clk 1>; + mali-supply = <&vdd_gpu>; + operating-points-v2 = <&gpu_opp_table>; + resets = <&reset 0>, <&reset 1>; + }; + + gpu_opp_table: opp_table0 { + compatible = "operating-points-v2"; + + opp@533000000 { + opp-hz = /bits/ 64 <533000000>; + opp-microvolt = <1250000>; + }; + opp@450000000 { + opp-hz = /bits/ 64 <450000000>; + opp-microvolt = <1150000>; + }; + opp@400000000 { + opp-hz = /bits/ 64 <400000000>; + opp-microvolt = <1125000>; + }; + opp@350000000 { + opp-hz = /bits/ 64 <350000000>; + opp-microvolt = <1075000>; + }; + opp@266000000 { + opp-hz = /bits/ 64 <266000000>; + opp-microvolt = <1025000>; + }; + opp@160000000 { + opp-hz = /bits/ 64 <160000000>; + opp-microvolt = <925000>; + }; + opp@100000000 { + opp-hz = /bits/ 64 <100000000>; + opp-microvolt = <912500>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt b/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt deleted file mode 100644 index 1b1a74129141..000000000000 --- a/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt +++ /dev/null @@ -1,101 +0,0 @@ -ARM Mali Midgard GPU -==================== - -Required properties: - -- compatible : - * Must contain one of the following: - + "arm,mali-t604" - + "arm,mali-t624" - + "arm,mali-t628" - + "arm,mali-t720" - + "arm,mali-t760" - + "arm,mali-t820" - + "arm,mali-t830" - + "arm,mali-t860" - + "arm,mali-t880" - * which must be preceded by one of the following vendor specifics: - + "amlogic,meson-gxm-mali" - + "rockchip,rk3288-mali" - + "rockchip,rk3399-mali" - -- reg : Physical base address of the device and length of the register area. - -- interrupts : Contains the three IRQ lines required by Mali Midgard devices. - -- interrupt-names : Contains the names of IRQ resources in the order they were - provided in the interrupts property. Must contain: "job", "mmu", "gpu". - - -Optional properties: - -- clocks : Phandle to clock for the Mali Midgard device. - -- mali-supply : Phandle to regulator for the Mali device. Refer to - Documentation/devicetree/bindings/regulator/regulator.txt for details. - -- operating-points-v2 : Refer to Documentation/devicetree/bindings/opp/opp.txt - for details. - -- resets : Phandle of the GPU reset line. - -Vendor-specific bindings ------------------------- - -The Mali GPU is integrated very differently from one SoC to -another. In order to accomodate those differences, you have the option -to specify one more vendor-specific compatible, among: - -- "amlogic,meson-gxm-mali" - Required properties: - - resets : Should contain phandles of : - + GPU reset line - + GPU APB glue reset line - -Example for a Mali-T760: - -gpu@ffa30000 { - compatible = "rockchip,rk3288-mali", "arm,mali-t760"; - reg = <0xffa30000 0x10000>; - interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "job", "mmu", "gpu"; - clocks = <&cru ACLK_GPU>; - mali-supply = <&vdd_gpu>; - operating-points-v2 = <&gpu_opp_table>; - power-domains = <&power RK3288_PD_GPU>; -}; - -gpu_opp_table: opp_table0 { - compatible = "operating-points-v2"; - - opp@533000000 { - opp-hz = /bits/ 64 <533000000>; - opp-microvolt = <1250000>; - }; - opp@450000000 { - opp-hz = /bits/ 64 <450000000>; - opp-microvolt = <1150000>; - }; - opp@400000000 { - opp-hz = /bits/ 64 <400000000>; - opp-microvolt = <1125000>; - }; - opp@350000000 { - opp-hz = /bits/ 64 <350000000>; - opp-microvolt = <1075000>; - }; - opp@266000000 { - opp-hz = /bits/ 64 <266000000>; - opp-microvolt = <1025000>; - }; - opp@160000000 { - opp-hz = /bits/ 64 <160000000>; - opp-microvolt = <925000>; - }; - opp@100000000 { - opp-hz = /bits/ 64 <100000000>; - opp-microvolt = <912500>; - }; -}; diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-midgard.yaml b/Documentation/devicetree/bindings/gpu/arm,mali-midgard.yaml new file mode 100644 index 000000000000..47bc1ac36426 --- /dev/null +++ b/Documentation/devicetree/bindings/gpu/arm,mali-midgard.yaml @@ -0,0 +1,168 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpu/arm,mali-midgard.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM Mali Midgard GPU + +maintainers: + - Rob Herring <robh@kernel.org> + +properties: + $nodename: + pattern: '^gpu@[a-f0-9]+$' + compatible: + oneOf: + - items: + - enum: + - allwinner,sun50i-h6-mali + - const: arm,mali-t720 + - items: + - enum: + - amlogic,meson-gxm-mali + - const: arm,mali-t820 + - items: + - enum: + - rockchip,rk3288-mali + - const: arm,mali-t760 + - items: + - enum: + - rockchip,rk3399-mali + - const: arm,mali-t860 + - items: + - enum: + - samsung,exynos5250-mali + - const: arm,mali-t604 + - items: + - enum: + - samsung,exynos5433-mali + - const: arm,mali-t760 + + # "arm,mali-t624" + # "arm,mali-t628" + # "arm,mali-t830" + # "arm,mali-t880" + + reg: + maxItems: 1 + + interrupts: + items: + - description: Job interrupt + - description: MMU interrupt + - description: GPU interrupt + + interrupt-names: + items: + - const: job + - const: mmu + - const: gpu + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + minItems: 1 + items: + - const: core + - const: bus + + mali-supply: + maxItems: 1 + + resets: + minItems: 1 + maxItems: 2 + + operating-points-v2: true + + "#cooling-cells": + const: 2 + +required: + - compatible + - reg + - interrupts + - interrupt-names + - clocks + +allOf: + - if: + properties: + compatible: + contains: + const: allwinner,sun50i-h6-mali + then: + properties: + clocks: + minItems: 2 + required: + - clock-names + - resets + - if: + properties: + compatible: + contains: + const: amlogic,meson-gxm-mali + then: + properties: + resets: + minItems: 2 + required: + - resets + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + gpu@ffa30000 { + compatible = "rockchip,rk3288-mali", "arm,mali-t760"; + reg = <0xffa30000 0x10000>; + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "job", "mmu", "gpu"; + clocks = <&cru 0>; + mali-supply = <&vdd_gpu>; + operating-points-v2 = <&gpu_opp_table>; + power-domains = <&power 0>; + #cooling-cells = <2>; + }; + + gpu_opp_table: opp_table0 { + compatible = "operating-points-v2"; + + opp@533000000 { + opp-hz = /bits/ 64 <533000000>; + opp-microvolt = <1250000>; + }; + opp@450000000 { + opp-hz = /bits/ 64 <450000000>; + opp-microvolt = <1150000>; + }; + opp@400000000 { + opp-hz = /bits/ 64 <400000000>; + opp-microvolt = <1125000>; + }; + opp@350000000 { + opp-hz = /bits/ 64 <350000000>; + opp-microvolt = <1075000>; + }; + opp@266000000 { + opp-hz = /bits/ 64 <266000000>; + opp-microvolt = <1025000>; + }; + opp@160000000 { + opp-hz = /bits/ 64 <160000000>; + opp-microvolt = <925000>; + }; + opp@100000000 { + opp-hz = /bits/ 64 <100000000>; + opp-microvolt = <912500>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt deleted file mode 100644 index ae63f09fda7d..000000000000 --- a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt +++ /dev/null @@ -1,123 +0,0 @@ -ARM Mali Utgard GPU -=================== - -Required properties: - - compatible - * Must be one of the following: - + "arm,mali-300" - + "arm,mali-400" - + "arm,mali-450" - * And, optionally, one of the vendor specific compatible: - + allwinner,sun4i-a10-mali - + allwinner,sun7i-a20-mali - + allwinner,sun8i-h3-mali - + allwinner,sun50i-a64-mali - + allwinner,sun50i-h5-mali - + amlogic,meson8-mali - + amlogic,meson8b-mali - + amlogic,meson-gxbb-mali - + amlogic,meson-gxl-mali - + rockchip,rk3036-mali - + rockchip,rk3066-mali - + rockchip,rk3188-mali - + rockchip,rk3228-mali - + rockchip,rk3328-mali - + stericsson,db8500-mali - - - reg: Physical base address and length of the GPU registers - - - interrupts: an entry for each entry in interrupt-names. - See ../interrupt-controller/interrupts.txt for details. - - - interrupt-names: - * ppX: Pixel Processor X interrupt (X from 0 to 7) - * ppmmuX: Pixel Processor X MMU interrupt (X from 0 to 7) - * pp: Pixel Processor broadcast interrupt (mali-450 only) - * gp: Geometry Processor interrupt - * gpmmu: Geometry Processor MMU interrupt - - - clocks: an entry for each entry in clock-names - - clock-names: - * bus: bus clock for the GPU - * core: clock driving the GPU itself - -Optional properties: - - interrupt-names and interrupts: - * pmu: Power Management Unit interrupt, if implemented in hardware - - - memory-region: - Memory region to allocate from, as defined in - Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt - - - mali-supply: - Phandle to regulator for the Mali device, as defined in - Documentation/devicetree/bindings/regulator/regulator.txt for details. - - - operating-points-v2: - Operating Points for the GPU, as defined in - Documentation/devicetree/bindings/opp/opp.txt - - - power-domains: - A power domain consumer specifier as defined in - Documentation/devicetree/bindings/power/power_domain.txt - -Vendor-specific bindings ------------------------- - -The Mali GPU is integrated very differently from one SoC to -another. In order to accomodate those differences, you have the option -to specify one more vendor-specific compatible, among: - - - allwinner,sun4i-a10-mali - Required properties: - * resets: phandle to the reset line for the GPU - - - allwinner,sun7i-a20-mali - Required properties: - * resets: phandle to the reset line for the GPU - - - allwinner,sun50i-a64-mali - Required properties: - * resets: phandle to the reset line for the GPU - - - allwinner,sun50i-h5-mali - Required properties: - * resets: phandle to the reset line for the GPU - - - amlogic,meson8-mali and amlogic,meson8b-mali - Required properties: - * resets: phandle to the reset line for the GPU - - - Rockchip variants: - Required properties: - * resets: phandle to the reset line for the GPU - - - stericsson,db8500-mali - Required properties: - * interrupt-names and interrupts: - + combined: combined interrupt of all of the above lines - -Example: - -mali: gpu@1c40000 { - compatible = "allwinner,sun7i-a20-mali", "arm,mali-400"; - reg = <0x01c40000 0x10000>; - interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "gp", - "gpmmu", - "pp0", - "ppmmu0", - "pp1", - "ppmmu1", - "pmu"; - clocks = <&ccu CLK_BUS_GPU>, <&ccu CLK_GPU>; - clock-names = "bus", "core"; - resets = <&ccu RST_BUS_GPU>; -}; - diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.yaml b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.yaml new file mode 100644 index 000000000000..c5d93c5839d3 --- /dev/null +++ b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.yaml @@ -0,0 +1,168 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpu/arm,mali-utgard.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM Mali Utgard GPU + +maintainers: + - Rob Herring <robh@kernel.org> + - Maxime Ripard <maxime.ripard@free-electrons.com> + - Heiko Stuebner <heiko@sntech.de> + +properties: + $nodename: + pattern: '^gpu@[a-f0-9]+$' + compatible: + oneOf: + - items: + - const: allwinner,sun8i-a23-mali + - const: allwinner,sun7i-a20-mali + - const: arm,mali-400 + - items: + - enum: + - allwinner,sun4i-a10-mali + - allwinner,sun7i-a20-mali + - allwinner,sun8i-h3-mali + - allwinner,sun50i-a64-mali + - rockchip,rk3036-mali + - rockchip,rk3066-mali + - rockchip,rk3188-mali + - rockchip,rk3228-mali + - samsung,exynos4210-mali + - stericsson,db8500-mali + - const: arm,mali-400 + - items: + - enum: + - allwinner,sun50i-h5-mali + - amlogic,meson8-mali + - amlogic,meson8b-mali + - amlogic,meson-gxbb-mali + - amlogic,meson-gxl-mali + - hisilicon,hi6220-mali + - rockchip,rk3328-mali + - const: arm,mali-450 + + # "arm,mali-300" + + reg: + maxItems: 1 + + interrupts: + minItems: 4 + maxItems: 20 + + interrupt-names: + allOf: + - additionalItems: true + minItems: 4 + maxItems: 20 + items: + # At least enforce the first 2 interrupts + - const: gp + - const: gpmmu + - items: + # Not ideal as any order and combination are allowed + enum: + - gp # Geometry Processor interrupt + - gpmmu # Geometry Processor MMU interrupt + - pp # Pixel Processor broadcast interrupt (mali-450 only) + - pp0 # Pixel Processor X interrupt (X from 0 to 7) + - ppmmu0 # Pixel Processor X MMU interrupt (X from 0 to 7) + - pp1 + - ppmmu1 + - pp2 + - ppmmu2 + - pp3 + - ppmmu3 + - pp4 + - ppmmu4 + - pp5 + - ppmmu5 + - pp6 + - ppmmu6 + - pp7 + - ppmmu7 + - pmu # Power Management Unit interrupt (optional) + - combined # stericsson,db8500-mali only + + clocks: + maxItems: 2 + + clock-names: + items: + - const: bus + - const: core + + memory-region: true + + mali-supply: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + operating-points-v2: true + +required: + - compatible + - reg + - interrupts + - interrupt-names + - clocks + - clock-names + +allOf: + - if: + properties: + compatible: + contains: + enum: + - allwinner,sun4i-a10-mali + - allwinner,sun7i-a20-mali + - allwinner,sun50i-a64-mali + - allwinner,sun50i-h5-mali + - amlogic,meson8-mali + - amlogic,meson8b-mali + - hisilicon,hi6220-mali + - rockchip,rk3036-mali + - rockchip,rk3066-mali + - rockchip,rk3188-mali + - rockchip,rk3228-mali + - rockchip,rk3328-mali + then: + required: + - resets + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + mali: gpu@1c40000 { + compatible = "allwinner,sun7i-a20-mali", "arm,mali-400"; + reg = <0x01c40000 0x10000>; + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "gp", + "gpmmu", + "pp0", + "ppmmu0", + "pp1", + "ppmmu1", + "pmu"; + clocks = <&ccu 1>, <&ccu 2>; + clock-names = "bus", "core"; + resets = <&ccu 1>; + }; + +... diff --git a/Documentation/devicetree/bindings/hwlock/omap-hwspinlock.txt b/Documentation/devicetree/bindings/hwlock/omap-hwspinlock.txt index 2c9804f4f4ac..8d365f89694c 100644 --- a/Documentation/devicetree/bindings/hwlock/omap-hwspinlock.txt +++ b/Documentation/devicetree/bindings/hwlock/omap-hwspinlock.txt @@ -1,12 +1,16 @@ -OMAP4+ HwSpinlock Driver -======================== +TI HwSpinlock for OMAP and K3 based SoCs +========================================= Required properties: -- compatible: Should be "ti,omap4-hwspinlock" for - OMAP44xx, OMAP54xx, AM33xx, AM43xx, DRA7xx SoCs +- compatible: Should be one of the following, + "ti,omap4-hwspinlock" for + OMAP44xx, OMAP54xx, AM33xx, AM43xx, DRA7xx SoCs + "ti,am654-hwspinlock" for + K3 AM65x and J721E SoCs - reg: Contains the hwspinlock module register address space (base address and length) - ti,hwmods: Name of the hwmod associated with the hwspinlock device + (for OMAP architecture based SoCs only) - #hwlock-cells: Should be 1. The OMAP hwspinlock users will use a 0-indexed relative hwlock number as the argument specifier value for requesting a specific hwspinlock @@ -17,10 +21,21 @@ Please look at the generic hwlock binding for usage information for consumers, Example: -/* OMAP4 */ +1. OMAP4 SoCs hwspinlock: spinlock@4a0f6000 { compatible = "ti,omap4-hwspinlock"; reg = <0x4a0f6000 0x1000>; ti,hwmods = "spinlock"; #hwlock-cells = <1>; }; + +2. AM65x SoCs and J721E SoCs +&cbass_main { + cbass_main_navss: interconnect0 { + hwspinlock: spinlock@30e00000 { + compatible = "ti,am654-hwspinlock"; + reg = <0x00 0x30e00000 0x00 0x1000>; + #hwlock-cells = <1>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/hwmon/as370.txt b/Documentation/devicetree/bindings/hwmon/as370.txt new file mode 100644 index 000000000000..d102fe765124 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/as370.txt @@ -0,0 +1,11 @@ +Bindings for Synaptics AS370 PVT sensors + +Required properties: +- compatible : "syna,as370-hwmon" +- reg : address and length of the register set. + +Example: + hwmon@ea0810 { + compatible = "syna,as370-hwmon"; + reg = <0xea0810 0xc>; + }; diff --git a/Documentation/devicetree/bindings/hwmon/ibm,cffps1.txt b/Documentation/devicetree/bindings/hwmon/ibm,cffps1.txt index f68a0a68fc52..1036f65fb778 100644 --- a/Documentation/devicetree/bindings/hwmon/ibm,cffps1.txt +++ b/Documentation/devicetree/bindings/hwmon/ibm,cffps1.txt @@ -1,8 +1,10 @@ -Device-tree bindings for IBM Common Form Factor Power Supply Version 1 ----------------------------------------------------------------------- +Device-tree bindings for IBM Common Form Factor Power Supply Versions 1 and 2 +----------------------------------------------------------------------------- Required properties: - - compatible = "ibm,cffps1"; + - compatible : Must be one of the following: + "ibm,cffps1" + "ibm,cffps2" - reg = < I2C bus address >; : Address of the power supply on the I2C bus. diff --git a/Documentation/devicetree/bindings/hwmon/lm75.txt b/Documentation/devicetree/bindings/hwmon/lm75.txt index 586b5ed70be7..273616702c51 100644 --- a/Documentation/devicetree/bindings/hwmon/lm75.txt +++ b/Documentation/devicetree/bindings/hwmon/lm75.txt @@ -15,6 +15,7 @@ Required properties: "maxim,max31725", "maxim,max31726", "maxim,mcp980x", + "nxp,pct2075", "st,stds75", "st,stlm75", "microchip,tcn75", diff --git a/Documentation/devicetree/bindings/i2c/allwinner,sun6i-a31-p2wi.yaml b/Documentation/devicetree/bindings/i2c/allwinner,sun6i-a31-p2wi.yaml new file mode 100644 index 000000000000..f9d526b7da01 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/allwinner,sun6i-a31-p2wi.yaml @@ -0,0 +1,65 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/i2c/allwinner,sun6i-a31-p2wi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A31 P2WI (Push/Pull 2 Wires Interface) Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +allOf: + - $ref: /schemas/i2c/i2c-controller.yaml# + +properties: + compatible: + const: allwinner,sun6i-a31-p2wi + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + clock-frequency: + minimum: 1 + maximum: 6000000 + +required: + - compatible + - reg + - interrupts + - clocks + - resets + +# FIXME: We should set it, but it would report all the generic +# properties as additional properties. +# additionalProperties: false + +examples: + - | + i2c@1f03400 { + compatible = "allwinner,sun6i-a31-p2wi"; + reg = <0x01f03400 0x400>; + interrupts = <0 39 4>; + clocks = <&apb0_gates 3>; + clock-frequency = <100000>; + resets = <&apb0_rst 3>; + #address-cells = <1>; + #size-cells = <0>; + + axp221: pmic@68 { + compatible = "x-powers,axp221"; + reg = <0x68>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/i2c/brcm,bcm2835-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,bcm2835-i2c.txt index e9de3756752b..c9a6587fe4bb 100644 --- a/Documentation/devicetree/bindings/i2c/brcm,bcm2835-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/brcm,bcm2835-i2c.txt @@ -1,7 +1,9 @@ Broadcom BCM2835 I2C controller Required properties: -- compatible : Should be "brcm,bcm2835-i2c". +- compatible : Should be one of: + "brcm,bcm2711-i2c" + "brcm,bcm2835-i2c" - reg: Should contain register location and length. - interrupts: Should contain interrupt. - clocks : The clock feeding the I2C controller. diff --git a/Documentation/devicetree/bindings/i2c/i2c-mt7621.txt b/Documentation/devicetree/bindings/i2c/i2c-mt7621.txt new file mode 100644 index 000000000000..bc36f0eb94cd --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mt7621.txt @@ -0,0 +1,25 @@ +MediaTek MT7621/MT7628 I2C master controller + +Required properties: + +- compatible: Should be one of the following: + - "mediatek,mt7621-i2c": for MT7621/MT7628/MT7688 platforms +- #address-cells: should be 1. +- #size-cells: should be 0. +- reg: Address and length of the register set for the device +- resets: phandle to the reset controller asserting this device in + reset + See ../reset/reset.txt for details. + +Optional properties : + +Example: + +i2c: i2c@900 { + compatible = "mediatek,mt7621-i2c"; + reg = <0x900 0x100>; + #address-cells = <1>; + #size-cells = <0>; + resets = <&rstctrl 16>; + reset-names = "i2c"; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-gpmux.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-gpmux.txt index 2907dab56298..8b444b94e92f 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mux-gpmux.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-gpmux.txt @@ -42,7 +42,7 @@ Optional properties: This means that no unrelated I2C transactions are allowed on the parent I2C adapter for the complete multiplexed I2C transaction. The properties of mux-locked and parent-locked multiplexers are discussed - in more detail in Documentation/i2c/i2c-topology. + in more detail in Documentation/i2c/i2c-topology.rst. For each i2c child node, an I2C child bus will be created. They will be numbered based on their order in the device tree. diff --git a/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt deleted file mode 100644 index 0ffe65a316ae..000000000000 --- a/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt +++ /dev/null @@ -1,64 +0,0 @@ - -* Marvell MV64XXX I2C controller - -Required properties : - - - reg : Offset and length of the register set for the device - - compatible : Should be either: - - "allwinner,sun4i-a10-i2c" - - "allwinner,sun6i-a31-i2c" - - "marvell,mv64xxx-i2c" - - "marvell,mv78230-i2c" - - "marvell,mv78230-a0-i2c" - * Note: Only use "marvell,mv78230-a0-i2c" for a - very rare, initial version of the SoC which - had broken offload support. Linux - auto-detects this and sets it appropriately. - - interrupts : The interrupt number - -Optional properties : - - - clock-frequency : Desired I2C bus clock frequency in Hz. If not set the -default frequency is 100kHz - - - resets : phandle to the parent reset controller. Mandatory - whenever you're using the "allwinner,sun6i-a31-i2c" - compatible. - - - clocks: : pointers to the reference clocks for this device, the - first one is the one used for the clock on the i2c bus, - the second one is the clock used to acces the registers - of the controller - - - clock-names : names of used clocks, mandatory if the second clock is - used, the name must be "core", and "reg" (the latter is - only for Armada 7K/8K). - -Examples: - - i2c@11000 { - compatible = "marvell,mv64xxx-i2c"; - reg = <0x11000 0x20>; - interrupts = <29>; - clock-frequency = <100000>; - }; - -For the Armada XP: - - i2c@11000 { - compatible = "marvell,mv78230-i2c", "marvell,mv64xxx-i2c"; - reg = <0x11000 0x100>; - interrupts = <29>; - clock-frequency = <100000>; - }; - -For the Armada 7040: - - i2c@701000 { - compatible = "marvell,mv78230-i2c"; - reg = <0x701000 0x20>; - interrupts = <29>; - clock-frequency = <100000>; - clock-names = "core", "reg"; - clocks = <&core_clock>, <®_clock>; - }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-ocores.txt b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt index 17bef9a34e50..6b25a80ae8d3 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-ocores.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt @@ -1,9 +1,13 @@ Device tree configuration for i2c-ocores Required properties: -- compatible : "opencores,i2c-ocores" or "aeroflexgaisler,i2cmst" +- compatible : "opencores,i2c-ocores" + "aeroflexgaisler,i2cmst" + "sifive,fu540-c000-i2c", "sifive,i2c0" + For Opencore based I2C IP block reimplemented in + FU540-C000 SoC. Please refer to sifive-blocks-ip-versioning.txt + for additional details. - reg : bus address start and address range size of device -- interrupts : interrupt number - clocks : handle to the controller clock; see the note below. Mutually exclusive with opencores,ip-clock-frequency - opencores,ip-clock-frequency: frequency of the controller clock in Hz; @@ -12,6 +16,7 @@ Required properties: - #size-cells : should be <0> Optional properties: +- interrupts : interrupt number. - clock-frequency : frequency of bus clock in Hz; see the note below. Defaults to 100 KHz when the property is not specified - reg-shift : device register offsets are shifted by this value diff --git a/Documentation/devicetree/bindings/i2c/i2c-omap.txt b/Documentation/devicetree/bindings/i2c/i2c-omap.txt index 4b90ba9f31b7..a44573d7c118 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-omap.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-omap.txt @@ -7,6 +7,7 @@ Required properties : "ti,omap3-i2c" for OMAP3 SoCs "ti,omap4-i2c" for OMAP4+ SoCs "ti,am654-i2c", "ti,omap4-i2c" for AM654 SoCs + "ti,j721e-i2c", "ti,omap4-i2c" for J721E SoCs - ti,hwmods : Must be "i2c<n>", n being the instance number (1-based) - #address-cells = <1>; - #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt index f334738f7a35..ce3df2fff6c8 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt @@ -21,6 +21,8 @@ Optional properties: 100000 and 400000. For STM32F7, STM32H7 and STM32MP1 SoCs, Standard-mode, Fast-mode and Fast-mode Plus are supported, possible values are 100000, 400000 and 1000000. +- dmas: List of phandles to rx and tx DMA channels. Refer to stm32-dma.txt. +- dma-names: List of dma names. Valid names are: "rx" and "tx". - i2c-scl-rising-time-ns: I2C SCL Rising time for the board (default: 25) For STM32F7, STM32H7 and STM32MP1 only. - i2c-scl-falling-time-ns: I2C SCL Falling time for the board (default: 10) diff --git a/Documentation/devicetree/bindings/i2c/i2c-sun6i-p2wi.txt b/Documentation/devicetree/bindings/i2c/i2c-sun6i-p2wi.txt deleted file mode 100644 index 49df0053347a..000000000000 --- a/Documentation/devicetree/bindings/i2c/i2c-sun6i-p2wi.txt +++ /dev/null @@ -1,41 +0,0 @@ - -* Allwinner P2WI (Push/Pull 2 Wire Interface) controller - -Required properties : - - - reg : Offset and length of the register set for the device. - - compatible : Should one of the following: - - "allwinner,sun6i-a31-p2wi" - - interrupts : The interrupt line connected to the P2WI peripheral. - - clocks : The gate clk connected to the P2WI peripheral. - - resets : The reset line connected to the P2WI peripheral. - -Optional properties : - - - clock-frequency : Desired P2WI bus clock frequency in Hz. If not set the -default frequency is 100kHz - -A P2WI may contain one child node encoding a P2WI slave device. - -Slave device properties: - Required properties: - - reg : the I2C slave address used during the initialization - process to switch from I2C to P2WI mode - -Example: - - p2wi@1f03400 { - compatible = "allwinner,sun6i-a31-p2wi"; - reg = <0x01f03400 0x400>; - interrupts = <0 39 4>; - clocks = <&apb0_gates 3>; - clock-frequency = <6000000>; - resets = <&apb0_rst 3>; - - axp221: pmic@68 { - compatible = "x-powers,axp221"; - reg = <0x68>; - - /* ... */ - }; - }; diff --git a/Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml b/Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml new file mode 100644 index 000000000000..c779000515d6 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml @@ -0,0 +1,127 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/i2c/marvell,mv64xxx-i2c.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell MV64XXX I2C Controller Device Tree Bindings + +maintainers: + - Gregory CLEMENT <gregory.clement@bootlin.com> + +properties: + compatible: + oneOf: + - const: allwinner,sun4i-a10-i2c + - items: + - const: allwinner,sun7i-a20-i2c + - const: allwinner,sun4i-a10-i2c + - const: allwinner,sun6i-a31-i2c + - items: + - const: allwinner,sun8i-a23-i2c + - const: allwinner,sun6i-a31-i2c + - items: + - const: allwinner,sun8i-a83t-i2c + - const: allwinner,sun6i-a31-i2c + - items: + - const: allwinner,sun50i-a64-i2c + - const: allwinner,sun6i-a31-i2c + - items: + - const: allwinner,sun50i-h6-i2c + - const: allwinner,sun6i-a31-i2c + + - const: marvell,mv64xxx-i2c + - const: marvell,mv78230-i2c + - const: marvell,mv78230-a0-i2c + + description: + Only use "marvell,mv78230-a0-i2c" for a very rare, initial + version of the SoC which had broken offload support. Linux + auto-detects this and sets it appropriately. + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 2 + items: + - description: Reference clock for the I2C bus + - description: Bus clock (Only for Armada 7K/8K) + + clock-names: + minItems: 1 + maxItems: 2 + items: + - const: core + - const: reg + description: + Mandatory if two clocks are used (only for Armada 7k and 8k). + + resets: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +allOf: + - $ref: /schemas/i2c/i2c-controller.yaml# + - if: + properties: + compatible: + contains: + enum: + - allwinner,sun4i-a10-i2c + - allwinner,sun6i-a31-i2c + + then: + required: + - clocks + + - if: + properties: + compatible: + contains: + const: allwinner,sun6i-a31-i2c + + then: + required: + - resets + +# FIXME: We should set it, but it would report all the generic +# properties as additional properties. +# additionalProperties: false + +examples: + - | + i2c@11000 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11000 0x20>; + interrupts = <29>; + clock-frequency = <100000>; + }; + + - | + i2c@11000 { + compatible = "marvell,mv78230-i2c"; + reg = <0x11000 0x100>; + interrupts = <29>; + clock-frequency = <100000>; + }; + + - | + i2c@701000 { + compatible = "marvell,mv78230-i2c"; + reg = <0x701000 0x20>; + interrupts = <29>; + clock-frequency = <100000>; + clock-names = "core", "reg"; + clocks = <&core_clock>, <®_clock>; + }; + +... diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/renesas,i2c.txt index 3ee5e8f6ee01..3ee5e8f6ee01 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt +++ b/Documentation/devicetree/bindings/i2c/renesas,i2c.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-emev2.txt b/Documentation/devicetree/bindings/i2c/renesas,iic-emev2.txt index 5ed1ea1c7e14..5ed1ea1c7e14 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-emev2.txt +++ b/Documentation/devicetree/bindings/i2c/renesas,iic-emev2.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt b/Documentation/devicetree/bindings/i2c/renesas,iic.txt index 202602e6e837..202602e6e837 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt +++ b/Documentation/devicetree/bindings/i2c/renesas,iic.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-riic.txt b/Documentation/devicetree/bindings/i2c/renesas,riic.txt index e26fe3ad86a9..e26fe3ad86a9 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-riic.txt +++ b/Documentation/devicetree/bindings/i2c/renesas,riic.txt diff --git a/Documentation/devicetree/bindings/i3c/cdns,i3c-master.txt b/Documentation/devicetree/bindings/i3c/cdns,i3c-master.txt index 69da2115abdc..1cf6182f888c 100644 --- a/Documentation/devicetree/bindings/i3c/cdns,i3c-master.txt +++ b/Documentation/devicetree/bindings/i3c/cdns,i3c-master.txt @@ -38,6 +38,6 @@ Example: nunchuk: nunchuk@52 { compatible = "nintendo,nunchuk"; - reg = <0x52 0x80000010 0>; + reg = <0x52 0x0 0x10>; }; }; diff --git a/Documentation/devicetree/bindings/i3c/i3c.txt b/Documentation/devicetree/bindings/i3c/i3c.txt index ab729a0a86ae..4ffe059f0fec 100644 --- a/Documentation/devicetree/bindings/i3c/i3c.txt +++ b/Documentation/devicetree/bindings/i3c/i3c.txt @@ -39,7 +39,9 @@ valid here, but several new properties have been added. New constraint on existing properties: -------------------------------------- - reg: contains 3 cells - + first cell : still encoding the I2C address + + first cell : still encoding the I2C address. 10 bit addressing is not + supported. Devices with 10 bit address can't be properly passed through + DEFSLVS command. + second cell: shall be 0 diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adxl345.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adxl345.yaml new file mode 100644 index 000000000000..c602b6fe1c0c --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/adi,adxl345.yaml @@ -0,0 +1,72 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/accel/adi,adxl345.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices ADXL345/ADXL375 3-Axis Digital Accelerometers + +maintainers: + - Michael Hennerich <michael.hennerich@analog.com> + +description: | + Analog Devices ADXL345/ADXL375 3-Axis Digital Accelerometers that supports + both I2C & SPI interfaces. + http://www.analog.com/en/products/mems/accelerometers/adxl345.html + http://www.analog.com/en/products/sensors-mems/accelerometers/adxl375.html + +properties: + compatible: + enum: + - adi,adxl345 + - adi,adxl375 + + reg: + maxItems: 1 + + spi-cpha: true + + spi-cpol: true + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + /* Example for a I2C device node */ + accelerometer@2a { + compatible = "adi,adxl345"; + reg = <0x53>; + interrupt-parent = <&gpio0>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + spi0 { + #address-cells = <1>; + #size-cells = <0>; + + /* Example for a SPI device node */ + accelerometer@0 { + compatible = "adi,adxl345"; + reg = <0>; + spi-max-frequency = <5000000>; + spi-cpol; + spi-cpha; + interrupt-parent = <&gpio0>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adxl372.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adxl372.yaml new file mode 100644 index 000000000000..e7daffec88d3 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/adi,adxl372.yaml @@ -0,0 +1,63 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/accel/adi,adxl372.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices ADXL372 3-Axis, +/-(200g) Digital Accelerometer + +maintainers: + - Stefan Popa <stefan.popa@analog.com> + +description: | + Analog Devices ADXL372 3-Axis, +/-(200g) Digital Accelerometer that supports + both I2C & SPI interfaces + https://www.analog.com/en/products/adxl372.html + +properties: + compatible: + enum: + - adi,adxl372 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + /* Example for a I2C device node */ + accelerometer@53 { + compatible = "adi,adxl372"; + reg = <0x53>; + interrupt-parent = <&gpio>; + interrupts = <25 IRQ_TYPE_EDGE_FALLING>; + }; + }; + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + spi0 { + #address-cells = <1>; + #size-cells = <0>; + + accelerometer@0 { + compatible = "adi,adxl372"; + reg = <0>; + spi-max-frequency = <1000000>; + interrupt-parent = <&gpio>; + interrupts = <25 IRQ_TYPE_EDGE_FALLING>; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/accel/adxl345.txt b/Documentation/devicetree/bindings/iio/accel/adxl345.txt deleted file mode 100644 index f9525f6e3d43..000000000000 --- a/Documentation/devicetree/bindings/iio/accel/adxl345.txt +++ /dev/null @@ -1,39 +0,0 @@ -Analog Devices ADXL345/ADXL375 3-Axis Digital Accelerometers - -http://www.analog.com/en/products/mems/accelerometers/adxl345.html -http://www.analog.com/en/products/sensors-mems/accelerometers/adxl375.html - -Required properties: - - compatible : should be one of - "adi,adxl345" - "adi,adxl375" - - reg : the I2C address or SPI chip select number of the sensor - -Required properties for SPI bus usage: - - spi-max-frequency : set maximum clock frequency, must be 5000000 - - spi-cpol and spi-cpha : must be defined for adxl345 to enable SPI mode 3 - -Optional properties: - - interrupts: interrupt mapping for IRQ as documented in - Documentation/devicetree/bindings/interrupt-controller/interrupts.txt - -Example for a I2C device node: - - accelerometer@2a { - compatible = "adi,adxl345"; - reg = <0x53>; - interrupt-parent = <&gpio1>; - interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; - }; - -Example for a SPI device node: - - accelerometer@0 { - compatible = "adi,adxl345"; - reg = <0>; - spi-max-frequency = <5000000>; - spi-cpol; - spi-cpha; - interrupt-parent = <&gpio1>; - interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; - }; diff --git a/Documentation/devicetree/bindings/iio/accel/adxl372.txt b/Documentation/devicetree/bindings/iio/accel/adxl372.txt deleted file mode 100644 index a289964756a7..000000000000 --- a/Documentation/devicetree/bindings/iio/accel/adxl372.txt +++ /dev/null @@ -1,33 +0,0 @@ -Analog Devices ADXL372 3-Axis, +/-(200g) Digital Accelerometer - -http://www.analog.com/media/en/technical-documentation/data-sheets/adxl372.pdf - -Required properties: - - compatible : should be "adi,adxl372" - - reg: the I2C address or SPI chip select number for the device - -Required properties for SPI bus usage: - - spi-max-frequency: Max SPI frequency to use - -Optional properties: - - interrupts: interrupt mapping for IRQ as documented in - Documentation/devicetree/bindings/interrupt-controller/interrupts.txt - -Example for a I2C device node: - - accelerometer@53 { - compatible = "adi,adxl372"; - reg = <0x53>; - interrupt-parent = <&gpio>; - interrupts = <25 IRQ_TYPE_EDGE_FALLING>; - }; - -Example for a SPI device node: - - accelerometer@0 { - compatible = "adi,adxl372"; - reg = <0>; - spi-max-frequency = <1000000>; - interrupt-parent = <&gpio>; - interrupts = <25 IRQ_TYPE_EDGE_FALLING>; - }; diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7124.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7124.txt deleted file mode 100644 index 416273dce569..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/adi,ad7124.txt +++ /dev/null @@ -1,75 +0,0 @@ -Analog Devices AD7124 ADC device driver - -Required properties for the AD7124: - - compatible: Must be one of "adi,ad7124-4" or "adi,ad7124-8" - - reg: SPI chip select number for the device - - spi-max-frequency: Max SPI frequency to use - see: Documentation/devicetree/bindings/spi/spi-bus.txt - - clocks: phandle to the master clock (mclk) - see: Documentation/devicetree/bindings/clock/clock-bindings.txt - - clock-names: Must be "mclk". - - interrupts: IRQ line for the ADC - see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt - - Required properties: - * #address-cells: Must be 1. - * #size-cells: Must be 0. - - Subnode(s) represent the external channels which are connected to the ADC. - Each subnode represents one channel and has the following properties: - Required properties: - * reg: The channel number. It can have up to 4 channels on ad7124-4 - and 8 channels on ad7124-8, numbered from 0 to 15. - * diff-channels: see: Documentation/devicetree/bindings/iio/adc/adc.txt - - Optional properties: - * bipolar: see: Documentation/devicetree/bindings/iio/adc/adc.txt - * adi,reference-select: Select the reference source to use when - converting on the the specific channel. Valid values are: - 0: REFIN1(+)/REFIN1(−). - 1: REFIN2(+)/REFIN2(−). - 3: AVDD - If this field is left empty, internal reference is selected. - -Optional properties: - - refin1-supply: refin1 supply can be used as reference for conversion. - - refin2-supply: refin2 supply can be used as reference for conversion. - - avdd-supply: avdd supply can be used as reference for conversion. - -Example: - adc@0 { - compatible = "adi,ad7124-4"; - reg = <0>; - spi-max-frequency = <5000000>; - interrupts = <25 2>; - interrupt-parent = <&gpio>; - refin1-supply = <&adc_vref>; - clocks = <&ad7124_mclk>; - clock-names = "mclk"; - - #address-cells = <1>; - #size-cells = <0>; - - channel@0 { - reg = <0>; - diff-channels = <0 1>; - adi,reference-select = <0>; - }; - - channel@1 { - reg = <1>; - bipolar; - diff-channels = <2 3>; - adi,reference-select = <0>; - }; - - channel@2 { - reg = <2>; - diff-channels = <4 5>; - }; - - channel@3 { - reg = <3>; - diff-channels = <6 7>; - }; - }; diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7124.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7124.yaml new file mode 100644 index 000000000000..9692b7f719f5 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7124.yaml @@ -0,0 +1,160 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 Analog Devices Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/bindings/iio/adc/adi,ad7124.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices AD7124 ADC device driver + +maintainers: + - Stefan Popa <stefan.popa@analog.com> + +description: | + Bindings for the Analog Devices AD7124 ADC device. Datasheet can be + found here: + https://www.analog.com/media/en/technical-documentation/data-sheets/AD7124-8.pdf + +properties: + compatible: + enum: + - adi,ad7124-4 + - adi,ad7124-8 + + reg: + description: SPI chip select number for the device + maxItems: 1 + + clocks: + maxItems: 1 + description: phandle to the master clock (mclk) + + clock-names: + items: + - const: mclk + + interrupts: + description: IRQ line for the ADC + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + refin1-supply: + description: refin1 supply can be used as reference for conversion. + maxItems: 1 + + refin2-supply: + description: refin2 supply can be used as reference for conversion. + maxItems: 1 + + avdd-supply: + description: avdd supply can be used as reference for conversion. + maxItems: 1 + +required: + - compatible + - reg + - clocks + - clock-names + - interrupts + +patternProperties: + "^channel@([0-9]|1[0-5])$": + type: object + description: | + Represents the external channels which are connected to the ADC. + See Documentation/devicetree/bindings/iio/adc/adc.txt. + + properties: + reg: + description: | + The channel number. It can have up to 8 channels on ad7124-4 + and 16 channels on ad7124-8, numbered from 0 to 15. + items: + minimum: 0 + maximum: 15 + + adi,reference-select: + description: | + Select the reference source to use when converting on + the specific channel. Valid values are: + 0: REFIN1(+)/REFIN1(−). + 1: REFIN2(+)/REFIN2(−). + 3: AVDD + If this field is left empty, internal reference is selected. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [0, 1, 3] + + diff-channels: + description: see Documentation/devicetree/bindings/iio/adc/adc.txt + items: + minimum: 0 + maximum: 15 + + bipolar: + description: see Documentation/devicetree/bindings/iio/adc/adc.txt + type: boolean + + adi,buffered-positive: + description: Enable buffered mode for positive input. + type: boolean + + adi,buffered-negative: + description: Enable buffered mode for negative input. + type: boolean + + required: + - reg + - diff-channels + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + compatible = "adi,ad7124-4"; + reg = <0>; + spi-max-frequency = <5000000>; + interrupts = <25 2>; + interrupt-parent = <&gpio>; + refin1-supply = <&adc_vref>; + clocks = <&ad7124_mclk>; + clock-names = "mclk"; + + #address-cells = <1>; + #size-cells = <0>; + + channel@0 { + reg = <0>; + diff-channels = <0 1>; + adi,reference-select = <0>; + adi,buffered-positive; + }; + + channel@1 { + reg = <1>; + bipolar; + diff-channels = <2 3>; + adi,reference-select = <0>; + adi,buffered-positive; + adi,buffered-negative; + }; + + channel@2 { + reg = <2>; + diff-channels = <4 5>; + }; + + channel@3 { + reg = <3>; + diff-channels = <6 7>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7192.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7192.yaml new file mode 100644 index 000000000000..676ec42e1438 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7192.yaml @@ -0,0 +1,121 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 Analog Devices Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/bindings/iio/adc/adi,ad7192.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices AD7192 ADC device driver + +maintainers: + - Michael Hennerich <michael.hennerich@analog.com> + +description: | + Bindings for the Analog Devices AD7192 ADC device. Datasheet can be + found here: + https://www.analog.com/media/en/technical-documentation/data-sheets/AD7192.pdf + +properties: + compatible: + enum: + - adi,ad7190 + - adi,ad7192 + - adi,ad7193 + - adi,ad7195 + + reg: + maxItems: 1 + + spi-cpol: true + + spi-cpha: true + + clocks: + maxItems: 1 + description: phandle to the master clock (mclk) + + clock-names: + items: + - const: mclk + + interrupts: + maxItems: 1 + + dvdd-supply: + description: DVdd voltage supply + items: + - const: dvdd + + avdd-supply: + description: AVdd voltage supply + items: + - const: avdd + + adi,rejection-60-Hz-enable: + description: | + This bit enables a notch at 60 Hz when the first notch of the sinc + filter is at 50 Hz. When REJ60 is set, a filter notch is placed at + 60 Hz when the sinc filter first notch is at 50 Hz. This allows + simultaneous 50 Hz/ 60 Hz rejection. + type: boolean + + adi,refin2-pins-enable: + description: | + External reference applied between the P1/REFIN2(+) and P0/REFIN2(−) pins. + type: boolean + + adi,buffer-enable: + description: | + Enables the buffer on the analog inputs. If cleared, the analog inputs + are unbuffered, lowering the power consumption of the device. If this + bit is set, the analog inputs are buffered, allowing the user to place + source impedances on the front end without contributing gain errors to + the system. + type: boolean + + adi,burnout-currents-enable: + description: | + When this bit is set to 1, the 500 nA current sources in the signal + path are enabled. When BURN = 0, the burnout currents are disabled. + The burnout currents can be enabled only when the buffer is active + and when chop is disabled. + type: boolean + + bipolar: + description: see Documentation/devicetree/bindings/iio/adc/adc.txt + type: boolean + +required: + - compatible + - reg + - clocks + - clock-names + - interrupts + - dvdd-supply + - avdd-supply + - spi-cpol + - spi-cpha + +examples: + - | + spi0 { + adc@0 { + compatible = "adi,ad7192"; + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpol; + spi-cpha; + clocks = <&ad7192_mclk>; + clock-names = "mclk"; + #interrupt-cells = <2>; + interrupts = <25 0x2>; + interrupt-parent = <&gpio>; + dvdd-supply = <&dvdd>; + avdd-supply = <&avdd>; + + adi,refin2-pins-enable; + adi,rejection-60-Hz-enable; + adi,buffer-enable; + adi,burnout-currents-enable; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt deleted file mode 100644 index d8652460198e..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt +++ /dev/null @@ -1,66 +0,0 @@ -Analog Devices AD7606 Simultaneous Sampling ADC - -Required properties for the AD7606: - -- compatible: Must be one of - * "adi,ad7605-4" - * "adi,ad7606-8" - * "adi,ad7606-6" - * "adi,ad7606-4" - * "adi,ad7616" -- reg: SPI chip select number for the device -- spi-max-frequency: Max SPI frequency to use - see: Documentation/devicetree/bindings/spi/spi-bus.txt -- spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt -- avcc-supply: phandle to the Avcc power supply -- interrupts: IRQ line for the ADC - see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt -- adi,conversion-start-gpios: must be the device tree identifier of the CONVST pin. - This logic input is used to initiate conversions on the analog - input channels. As the line is active high, it should be marked - GPIO_ACTIVE_HIGH. - -Optional properties: - -- reset-gpios: must be the device tree identifier of the RESET pin. If specified, - it will be asserted during driver probe. As the line is active high, - it should be marked GPIO_ACTIVE_HIGH. -- standby-gpios: must be the device tree identifier of the STBY pin. This pin is used - to place the AD7606 into one of two power-down modes, Standby mode or - Shutdown mode. As the line is active low, it should be marked - GPIO_ACTIVE_LOW. -- adi,first-data-gpios: must be the device tree identifier of the FRSTDATA pin. - The FRSTDATA output indicates when the first channel, V1, is - being read back on either the parallel, byte or serial interface. - As the line is active high, it should be marked GPIO_ACTIVE_HIGH. -- adi,range-gpios: must be the device tree identifier of the RANGE pin. The polarity on - this pin determines the input range of the analog input channels. If - this pin is tied to a logic high, the analog input range is ±10V for - all channels. If this pin is tied to a logic low, the analog input range - is ±5V for all channels. As the line is active high, it should be marked - GPIO_ACTIVE_HIGH. -- adi,oversampling-ratio-gpios: must be the device tree identifier of the over-sampling - mode pins. As the line is active high, it should be marked - GPIO_ACTIVE_HIGH. - -Example: - - adc@0 { - compatible = "adi,ad7606-8"; - reg = <0>; - spi-max-frequency = <1000000>; - spi-cpol; - - avcc-supply = <&adc_vref>; - - interrupts = <25 IRQ_TYPE_EDGE_FALLING>; - interrupt-parent = <&gpio>; - - adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; - reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>; - adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; - adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH - &gpio 23 GPIO_ACTIVE_HIGH - &gpio 26 GPIO_ACTIVE_HIGH>; - standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>; - }; diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml new file mode 100644 index 000000000000..cc544fdc38be --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml @@ -0,0 +1,138 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/adi,ad7606.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices AD7606 Simultaneous Sampling ADC + +maintainers: + - Beniamin Bia <beniamin.bia@analog.com> + - Stefan Popa <stefan.popa@analog.com> + +description: | + Analog Devices AD7606 Simultaneous Sampling ADC + https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606_7606-6_7606-4.pdf + https://www.analog.com/media/en/technical-documentation/data-sheets/AD7606B.pdf + https://www.analog.com/media/en/technical-documentation/data-sheets/AD7616.pdf + +properties: + compatible: + enum: + - adi,ad7605-4 + - adi,ad7606-8 + - adi,ad7606-6 + - adi,ad7606-4 + - adi,ad7606b + - adi,ad7616 + + reg: + maxItems: 1 + + spi-cpha: true + + avcc-supply: + description: + Phandle to the Avcc power supply + maxItems: 1 + + interrupts: + maxItems: 1 + + adi,conversion-start-gpios: + description: + Must be the device tree identifier of the CONVST pin. + This logic input is used to initiate conversions on the analog + input channels. As the line is active high, it should be marked + GPIO_ACTIVE_HIGH. + maxItems: 1 + + reset-gpios: + description: + Must be the device tree identifier of the RESET pin. If specified, + it will be asserted during driver probe. As the line is active high, + it should be marked GPIO_ACTIVE_HIGH. + maxItems: 1 + + standby-gpios: + description: + Must be the device tree identifier of the STBY pin. This pin is used + to place the AD7606 into one of two power-down modes, Standby mode or + Shutdown mode. As the line is active low, it should be marked + GPIO_ACTIVE_LOW. + maxItems: 1 + + adi,first-data-gpios: + description: + Must be the device tree identifier of the FRSTDATA pin. + The FRSTDATA output indicates when the first channel, V1, is + being read back on either the parallel, byte or serial interface. + As the line is active high, it should be marked GPIO_ACTIVE_HIGH. + maxItems: 1 + + adi,range-gpios: + description: + Must be the device tree identifier of the RANGE pin. The polarity on + this pin determines the input range of the analog input channels. If + this pin is tied to a logic high, the analog input range is ±10V for + all channels. If this pin is tied to a logic low, the analog input range + is ±5V for all channels. As the line is active high, it should be marked + GPIO_ACTIVE_HIGH. + maxItems: 1 + + adi,oversampling-ratio-gpios: + description: + Must be the device tree identifier of the over-sampling + mode pins. As the line is active high, it should be marked + GPIO_ACTIVE_HIGH. + maxItems: 1 + + adi,sw-mode: + description: + Software mode of operation, so far available only for ad7616 and ad7606b. + It is enabled when all three oversampling mode pins are connected to + high level. The device is configured by the corresponding registers. If the + adi,oversampling-ratio-gpios property is defined, then the driver will set the + oversampling gpios to high. Otherwise, it is assumed that the pins are hardwired + to VDD. + type: boolean + +required: + - compatible + - reg + - spi-cpha + - avcc-supply + - interrupts + - adi,conversion-start-gpios + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + spi0 { + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + compatible = "adi,ad7606-8"; + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpol; + spi-cpha; + + avcc-supply = <&adc_vref>; + + interrupts = <25 IRQ_TYPE_EDGE_FALLING>; + interrupt-parent = <&gpio>; + + adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>; + adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; + adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH + &gpio 23 GPIO_ACTIVE_HIGH + &gpio 26 GPIO_ACTIVE_HIGH>; + standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>; + adi,sw-mode; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7780.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7780.txt deleted file mode 100644 index 440e52555349..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/adi,ad7780.txt +++ /dev/null @@ -1,48 +0,0 @@ -* Analog Devices AD7170/AD7171/AD7780/AD7781 - -Data sheets: - -- AD7170: - * https://www.analog.com/media/en/technical-documentation/data-sheets/AD7170.pdf -- AD7171: - * https://www.analog.com/media/en/technical-documentation/data-sheets/AD7171.pdf -- AD7780: - * https://www.analog.com/media/en/technical-documentation/data-sheets/ad7780.pdf -- AD7781: - * https://www.analog.com/media/en/technical-documentation/data-sheets/AD7781.pdf - -Required properties: - -- compatible: should be one of - * "adi,ad7170" - * "adi,ad7171" - * "adi,ad7780" - * "adi,ad7781" -- reg: spi chip select number for the device -- vref-supply: the regulator supply for the ADC reference voltage - -Optional properties: - -- powerdown-gpios: must be the device tree identifier of the PDRST pin. If - specified, it will be asserted during driver probe. As the - line is active high, it should be marked GPIO_ACTIVE_HIGH. -- adi,gain-gpios: must be the device tree identifier of the GAIN pin. Only for - the ad778x chips. If specified, it will be asserted during - driver probe. As the line is active low, it should be marked - GPIO_ACTIVE_LOW. -- adi,filter-gpios: must be the device tree identifier of the FILTER pin. Only - for the ad778x chips. If specified, it will be asserted - during driver probe. As the line is active low, it should be - marked GPIO_ACTIVE_LOW. - -Example: - -adc@0 { - compatible = "adi,ad7780"; - reg = <0>; - vref-supply = <&vdd_supply> - - powerdown-gpios = <&gpio 12 GPIO_ACTIVE_HIGH>; - adi,gain-gpios = <&gpio 5 GPIO_ACTIVE_LOW>; - adi,filter-gpios = <&gpio 15 GPIO_ACTIVE_LOW>; -}; diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7780.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7780.yaml new file mode 100644 index 000000000000..d1109416963c --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7780.yaml @@ -0,0 +1,87 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/adi,ad7780.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices AD7170/AD7171/AD7780/AD7781 analog to digital converters + +maintainers: + - Michael Hennerich <michael.hennerich@analog.com> + +description: | + The ad7780 is a sigma-delta analog to digital converter. This driver provides + reading voltage values and status bits from both the ad778x and ad717x series. + Its interface also allows writing on the FILTER and GAIN GPIO pins on the + ad778x. + + Specifications on the converters can be found at: + AD7170: + https://www.analog.com/media/en/technical-documentation/data-sheets/AD7170.pdf + AD7171: + https://www.analog.com/media/en/technical-documentation/data-sheets/AD7171.pdf + AD7780: + https://www.analog.com/media/en/technical-documentation/data-sheets/ad7780.pdf + AD7781: + https://www.analog.com/media/en/technical-documentation/data-sheets/AD7781.pdf + +properties: + compatible: + enum: + - adi,ad7170 + - adi,ad7171 + - adi,ad7780 + - adi,ad7781 + + reg: + maxItems: 1 + + avdd-supply: + description: + The regulator supply for the ADC reference voltage. + maxItems: 1 + + powerdown-gpios: + description: + Must be the device tree identifier of the PDRST pin. If + specified, it will be asserted during driver probe. As the + line is active high, it should be marked GPIO_ACTIVE_HIGH. + maxItems: 1 + + adi,gain-gpios: + description: + Must be the device tree identifier of the GAIN pin. Only for + the ad778x chips. If specified, it will be asserted during + driver probe. As the line is active low, it should be marked + GPIO_ACTIVE_LOW. + maxItems: 1 + + adi,filter-gpios: + description: + Must be the device tree identifier of the FILTER pin. Only + for the ad778x chips. If specified, it will be asserted + during driver probe. As the line is active low, it should be + marked GPIO_ACTIVE_LOW. + maxItems: 1 + +required: + - compatible + - reg + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + spi0 { + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + compatible = "adi,ad7780"; + reg = <0>; + + avdd-supply = <&vdd_supply>; + powerdown-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + adi,gain-gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; + adi,filter-gpios = <&gpio2 15 GPIO_ACTIVE_LOW>; + }; + }; diff --git a/Documentation/devicetree/bindings/hwmon/ads1015.txt b/Documentation/devicetree/bindings/iio/adc/ads1015.txt index 918a507d1159..918a507d1159 100644 --- a/Documentation/devicetree/bindings/hwmon/ads1015.txt +++ b/Documentation/devicetree/bindings/iio/adc/ads1015.txt diff --git a/Documentation/devicetree/bindings/iio/adc/allwinner,sun8i-a33-ths.yaml b/Documentation/devicetree/bindings/iio/adc/allwinner,sun8i-a33-ths.yaml new file mode 100644 index 000000000000..d74962c0f5ae --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/allwinner,sun8i-a33-ths.yaml @@ -0,0 +1,43 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/allwinner,sun8i-a33-ths.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A33 Thermal Sensor Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + "#io-channel-cells": + const: 0 + + "#thermal-sensor-cells": + const: 0 + + compatible: + const: allwinner,sun8i-a33-ths + + reg: + maxItems: 1 + +required: + - "#io-channel-cells" + - "#thermal-sensor-cells" + - compatible + - reg + +additionalProperties: false + +examples: + - | + ths: ths@1c25000 { + compatible = "allwinner,sun8i-a33-ths"; + reg = <0x01c25000 0x100>; + #thermal-sensor-cells = <0>; + #io-channel-cells = <0>; + }; + +... diff --git a/Documentation/devicetree/bindings/iio/adc/avia-hx711.yaml b/Documentation/devicetree/bindings/iio/adc/avia-hx711.yaml index 8a4100ceeaf2..d76ece97c76c 100644 --- a/Documentation/devicetree/bindings/iio/adc/avia-hx711.yaml +++ b/Documentation/devicetree/bindings/iio/adc/avia-hx711.yaml @@ -61,6 +61,6 @@ examples: compatible = "avia,hx711"; sck-gpios = <&gpio3 10 GPIO_ACTIVE_HIGH>; dout-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; - avdd-suppy = <&avdd>; + avdd-supply = <&avdd>; clock-frequency = <100000>; }; diff --git a/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt b/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt index 0df9befdaecc..78c06e05c8e5 100644 --- a/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt +++ b/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt @@ -13,8 +13,10 @@ Required properties: - compatible: Should be one of: - "mediatek,mt2701-auxadc": For MT2701 family of SoCs - "mediatek,mt2712-auxadc": For MT2712 family of SoCs + - "mediatek,mt6765-auxadc": For MT6765 family of SoCs - "mediatek,mt7622-auxadc": For MT7622 family of SoCs - "mediatek,mt8173-auxadc": For MT8173 family of SoCs + - "mediatek,mt8183-auxadc", "mediatek,mt8173-auxadc": For MT8183 family of SoCs - reg: Address range of the AUXADC unit. - clocks: Should contain a clock specifier for each entry in clock-names - clock-names: Should contain "main". diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt index 8346bcb04ad7..4c0da8c74bb2 100644 --- a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt @@ -38,6 +38,7 @@ Required properties: It's required on stm32h7. - clock-names: Must be "adc" and/or "bus" depending on part used. - interrupt-controller: Identifies the controller node as interrupt-parent +- vdda-supply: Phandle to the vdda input analog voltage. - vref-supply: Phandle to the vref input analog reference voltage. - #interrupt-cells = <1>; - #address-cells = <1>; @@ -46,6 +47,12 @@ Required properties: Optional properties: - A pinctrl state named "default" for each ADC channel may be defined to set inX ADC pins in mode of operation for analog input on external pin. +- booster-supply: Phandle to the embedded booster regulator that can be used + to supply ADC analog input switches on stm32h7 and stm32mp1. +- vdd-supply: Phandle to the vdd input voltage. It can be used to supply ADC + analog input switches on stm32mp1. +- st,syscfg: Phandle to system configuration controller. It can be used to + control the analog circuitry on stm32mp1. Contents of a stm32 adc child node: ----------------------------------- diff --git a/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt b/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt deleted file mode 100644 index c52ea2126eaa..000000000000 --- a/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt +++ /dev/null @@ -1,26 +0,0 @@ -* Plantower PMS7003 particulate matter sensor - -Required properties: -- compatible: must one of: - "plantower,pms1003" - "plantower,pms3003" - "plantower,pms5003" - "plantower,pms6003" - "plantower,pms7003" - "plantower,pmsa003" -- vcc-supply: phandle to the regulator that provides power to the sensor - -Optional properties: -- plantower,set-gpios: phandle to the GPIO connected to the SET line -- reset-gpios: phandle to the GPIO connected to the RESET line - -Refer to serial/slave-device.txt for generic serial attached device bindings. - -Example: - -&uart0 { - air-pollution-sensor { - compatible = "plantower,pms7003"; - vcc-supply = <®_vcc5v0>; - }; -}; diff --git a/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.yaml b/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.yaml new file mode 100644 index 000000000000..a551d3101f93 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.yaml @@ -0,0 +1,51 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/chemical/plantower,pms7003.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Plantower PMS7003 air pollution sensor + +maintainers: + - Tomasz Duszynski <tduszyns@gmail.com> + +description: | + Air pollution sensor capable of measuring mass concentration of dust + particles. + +properties: + compatible: + enum: + - plantower,pms1003 + - plantower,pms3003 + - plantower,pms5003 + - plantower,pms6003 + - plantower,pms7003 + - plantower,pmsa003 + + vcc-supply: + description: regulator that provides power to the sensor + maxItems: 1 + + plantower,set-gpios: + description: GPIO connected to the SET line + maxItems: 1 + + reset-gpios: + description: GPIO connected to the RESET line + maxItems: 1 + +required: + - compatible + - vcc-supply + +examples: + - | + serial { + air-pollution-sensor { + compatible = "plantower,pms7003"; + vcc-supply = <®_vcc5v0>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/iio/chemical/sensirion,sps30.txt b/Documentation/devicetree/bindings/iio/chemical/sensirion,sps30.txt deleted file mode 100644 index 6eee2709b5b6..000000000000 --- a/Documentation/devicetree/bindings/iio/chemical/sensirion,sps30.txt +++ /dev/null @@ -1,12 +0,0 @@ -* Sensirion SPS30 particulate matter sensor - -Required properties: -- compatible: must be "sensirion,sps30" -- reg: the I2C address of the sensor - -Example: - -sps30@69 { - compatible = "sensirion,sps30"; - reg = <0x69>; -}; diff --git a/Documentation/devicetree/bindings/iio/chemical/sensirion,sps30.yaml b/Documentation/devicetree/bindings/iio/chemical/sensirion,sps30.yaml new file mode 100644 index 000000000000..50a50a0d7070 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/chemical/sensirion,sps30.yaml @@ -0,0 +1,39 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/chemical/sensirion,sps30.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sensirion SPS30 particulate matter sensor + +maintainers: + - Tomasz Duszynski <tduszyns@gmail.com> + +description: | + Air pollution sensor capable of measuring mass concentration of dust + particles. + +properties: + compatible: + enum: + - sensirion,sps30 + reg: + maxItems: 1 + +required: + - compatible + - reg + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + air-pollution-sensor@69 { + compatible = "sensirion,sps30"; + reg = <0x69>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/iio/frequency/adf4371.yaml b/Documentation/devicetree/bindings/iio/frequency/adf4371.yaml new file mode 100644 index 000000000000..7ec3ec94356b --- /dev/null +++ b/Documentation/devicetree/bindings/iio/frequency/adf4371.yaml @@ -0,0 +1,63 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/frequency/adf4371.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices ADF4371/ADF4372 Wideband Synthesizers + +maintainers: + - Popa Stefan <stefan.popa@analog.com> + +description: | + Analog Devices ADF4371/ADF4372 SPI Wideband Synthesizers + https://www.analog.com/media/en/technical-documentation/data-sheets/adf4371.pdf + https://www.analog.com/media/en/technical-documentation/data-sheets/adf4372.pdf + +properties: + compatible: + enum: + - adi,adf4371 + - adi,adf4372 + + reg: + maxItems: 1 + + clocks: + description: + Definition of the external clock (see clock/clock-bindings.txt) + maxItems: 1 + + clock-names: + description: + Must be "clkin" + maxItems: 1 + + adi,mute-till-lock-en: + type: boolean + description: + If this property is present, then the supply current to RF8P and RF8N + output stage will shut down until the ADF4371/ADF4372 achieves lock as + measured by the digital lock detect circuitry. + +required: + - compatible + - reg + - clocks + - clock-names + +examples: + - | + spi0 { + #address-cells = <1>; + #size-cells = <0>; + + frequency@0 { + compatible = "adi,adf4371"; + reg = <0>; + spi-max-frequency = <1000000>; + clocks = <&adf4371_clkin>; + clock-names = "clkin"; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/imu/adi,adis16460.yaml b/Documentation/devicetree/bindings/iio/imu/adi,adis16460.yaml new file mode 100644 index 000000000000..0c53009ba7d6 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/imu/adi,adis16460.yaml @@ -0,0 +1,53 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/imu/adi,adis16460.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices ADIS16460 and similar IMUs + +maintainers: + - Dragos Bogdan <dragos.bogdan@analog.com> + +description: | + Analog Devices ADIS16460 and similar IMUs + https://www.analog.com/media/en/technical-documentation/data-sheets/ADIS16460.pdf + +properties: + compatible: + enum: + - adi,adis16460 + + reg: + maxItems: 1 + + spi-cpha: true + + spi-cpol: true + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + spi0 { + #address-cells = <1>; + #size-cells = <0>; + + imu@0 { + compatible = "adi,adis16460"; + reg = <0>; + spi-max-frequency = <5000000>; + spi-cpol; + spi-cpha; + interrupt-parent = <&gpio0>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt index efec9ece034a..6d0c050d89fe 100644 --- a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt +++ b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt @@ -11,6 +11,9 @@ Required properties: "st,asm330lhh" "st,lsm6dsox" "st,lsm6dsr" + "st,lsm6ds3tr-c" + "st,ism330dhcx" + "st,lsm9ds1-imu" - reg: i2c address of the sensor / spi cs line Optional properties: diff --git a/Documentation/devicetree/bindings/iio/light/isl29018.txt b/Documentation/devicetree/bindings/iio/light/isl29018.txt deleted file mode 100644 index b9bbde3e13ed..000000000000 --- a/Documentation/devicetree/bindings/iio/light/isl29018.txt +++ /dev/null @@ -1,27 +0,0 @@ -* ISL 29018/29023/29035 I2C ALS, Proximity, and Infrared sensor - -Required properties: - - - compatible: Should be one of - "isil,isl29018" - "isil,isl29023" - "isil,isl29035" - - reg: the I2C address of the device - -Optional properties: - - - interrupts: the sole interrupt generated by the device - - Refer to interrupt-controller/interrupts.txt for generic interrupt client - node bindings. - - - vcc-supply: phandle to the regulator that provides power to the sensor. - -Example: - -isl29018@44 { - compatible = "isil,isl29018"; - reg = <0x44>; - interrupt-parent = <&gpio>; - interrupts = <TEGRA_GPIO(Z, 2) IRQ_TYPE_LEVEL_HIGH>; -}; diff --git a/Documentation/devicetree/bindings/iio/light/isl29018.yaml b/Documentation/devicetree/bindings/iio/light/isl29018.yaml new file mode 100644 index 000000000000..cbb00be8f359 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/isl29018.yaml @@ -0,0 +1,56 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/light/isl29018.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: | + Intersil 29018/29023/29035 Ambient Light, Infrared Light, and Proximity Sensor + +maintainers: + - Brian Masney <masneyb@onstation.org> + +description: | + Ambient and infrared light sensing with proximity detection over an i2c + interface. + + https://www.renesas.com/us/en/www/doc/datasheet/isl29018.pdf + https://www.renesas.com/us/en/www/doc/datasheet/isl29023.pdf + https://www.renesas.com/us/en/www/doc/datasheet/isl29035.pdf + +properties: + compatible: + enum: + - isil,isl29018 + - isil,isl29023 + - isil,isl29035 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + vcc-supply: + description: Regulator that provides power to the sensor + +required: + - compatible + - reg + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + + #address-cells = <1>; + #size-cells = <0>; + + sensor@44 { + compatible = "isil,isl29018"; + reg = <0x44>; + interrupts-extended = <&msmgpio 61 IRQ_TYPE_LEVEL_HIGH>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/light/noa1305.yaml b/Documentation/devicetree/bindings/iio/light/noa1305.yaml new file mode 100644 index 000000000000..17e7f140b69b --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/noa1305.yaml @@ -0,0 +1,44 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/light/noa1305.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ON Semiconductor NOA1305 Ambient Light Sensor + +maintainers: + - Martyn Welch <martyn.welch@collabora.com> + +description: | + Ambient sensing with an i2c interface. + + https://www.onsemi.com/pub/Collateral/NOA1305-D.PDF + +properties: + compatible: + enum: + - onnn,noa1305 + + reg: + maxItems: 1 + + vin-supply: + description: Regulator that provides power to the sensor + +required: + - compatible + - reg + +examples: + - | + i2c { + + #address-cells = <1>; + #size-cells = <0>; + + light@39 { + compatible = "onnn,noa1305"; + reg = <0x39>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/light/isl29501.txt b/Documentation/devicetree/bindings/iio/light/renesas,isl29501.txt index 46957997fee3..46957997fee3 100644 --- a/Documentation/devicetree/bindings/iio/light/isl29501.txt +++ b/Documentation/devicetree/bindings/iio/light/renesas,isl29501.txt diff --git a/Documentation/devicetree/bindings/iio/light/stk33xx.yaml b/Documentation/devicetree/bindings/iio/light/stk33xx.yaml new file mode 100644 index 000000000000..aae8a6d627c9 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/stk33xx.yaml @@ -0,0 +1,49 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/light/stk33xx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: | + Sensortek STK33xx I2C Ambient Light and Proximity sensor + +maintainers: + - Jonathan Cameron <jic23@kernel.org> + +description: | + Ambient light and proximity sensor over an i2c interface. + +properties: + compatible: + enum: + - sensortek,stk3310 + - sensortek,stk3311 + - sensortek,stk3335 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + + #address-cells = <1>; + #size-cells = <0>; + + stk3310@48 { + compatible = "sensortek,stk3310"; + reg = <0x48>; + interrupt-parent = <&gpio1>; + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/light/tsl2583.txt b/Documentation/devicetree/bindings/iio/light/tsl2583.txt deleted file mode 100644 index 059dffa1829a..000000000000 --- a/Documentation/devicetree/bindings/iio/light/tsl2583.txt +++ /dev/null @@ -1,25 +0,0 @@ -* TAOS TSL 2580/2581/2583 ALS sensor - -Required properties: - - - compatible: Should be one of - "amstaos,tsl2580" - "amstaos,tsl2581" - "amstaos,tsl2583" - - reg: the I2C address of the device - -Optional properties: - - - interrupts: the sole interrupt generated by the device - - Refer to interrupt-controller/interrupts.txt for generic interrupt client - node bindings. - - - vcc-supply: phandle to the regulator that provides power to the sensor. - -Example: - -tsl2581@29 { - compatible = "amstaos,tsl2581"; - reg = <0x29>; -}; diff --git a/Documentation/devicetree/bindings/iio/light/tsl2583.yaml b/Documentation/devicetree/bindings/iio/light/tsl2583.yaml new file mode 100644 index 000000000000..e86ef64ecf03 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/tsl2583.yaml @@ -0,0 +1,46 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/light/tsl2583.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: AMS/TAOS Ambient Light Sensor (ALS) + +maintainers: + - Brian Masney <masneyb@onstation.org> + +description: | + Ambient light sensing with an i2c interface. + +properties: + compatible: + enum: + - amstaos,tsl2580 + - amstaos,tsl2581 + - amstaos,tsl2583 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + vcc-supply: + description: Regulator that provides power to the sensor + +required: + - compatible + - reg + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + light-sensor@29 { + compatible = "amstaos,tsl2581"; + reg = <0x29>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/light/tsl2772.txt b/Documentation/devicetree/bindings/iio/light/tsl2772.txt deleted file mode 100644 index 1c5e6f17a1df..000000000000 --- a/Documentation/devicetree/bindings/iio/light/tsl2772.txt +++ /dev/null @@ -1,42 +0,0 @@ -* AMS/TAOS ALS and proximity sensor - -Required properties: - - - compatible: Should be one of - "amstaos,tsl2571" - "amstaos,tsl2671" - "amstaos,tmd2671" - "amstaos,tsl2771" - "amstaos,tmd2771" - "amstaos,tsl2572" - "amstaos,tsl2672" - "amstaos,tmd2672" - "amstaos,tsl2772" - "amstaos,tmd2772" - "avago,apds9930" - - reg: the I2C address of the device - -Optional properties: - - - amstaos,proximity-diodes - proximity diodes to enable. <0>, <1>, or <0 1> - are the only valid values. - - led-max-microamp - current for the proximity LED. Must be 100000, 50000, - 25000, or 13000. - - vdd-supply: phandle to the regulator that provides power to the sensor. - - vddio-supply: phandle to the regulator that provides power to the bus. - - interrupts: the sole interrupt generated by the device - - Refer to interrupt-controller/interrupts.txt for generic interrupt client - node bindings. - -Example: - -tsl2772@39 { - compatible = "amstaos,tsl2772"; - reg = <0x39>; - interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>; - vdd-supply = <&pm8941_l17>; - vddio-supply = <&pm8941_lvs1>; - amstaos,proximity-diodes = <0>; - led-max-microamp = <100000>; -}; diff --git a/Documentation/devicetree/bindings/iio/light/tsl2772.yaml b/Documentation/devicetree/bindings/iio/light/tsl2772.yaml new file mode 100644 index 000000000000..ed2c3d5eadf5 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/tsl2772.yaml @@ -0,0 +1,83 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/light/tsl2772.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: AMS/TAOS Ambient Light Sensor (ALS) and Proximity Detector + +maintainers: + - Brian Masney <masneyb@onstation.org> + +description: | + Ambient light sensing and proximity detection with an i2c interface. + https://ams.com/documents/20143/36005/TSL2772_DS000181_2-00.pdf + +properties: + compatible: + enum: + - amstaos,tsl2571 + - amstaos,tsl2671 + - amstaos,tmd2671 + - amstaos,tsl2771 + - amstaos,tmd2771 + - amstaos,tsl2572 + - amstaos,tsl2672 + - amstaos,tmd2672 + - amstaos,tsl2772 + - amstaos,tmd2772 + - avago,apds9930 + + reg: + maxItems: 1 + + amstaos,proximity-diodes: + description: Proximity diodes to enable + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + - minItems: 1 + maxItems: 2 + items: + minimum: 0 + maximum: 1 + + interrupts: + maxItems: 1 + + led-max-microamp: + description: Current for the proximity LED + enum: + - 13000 + - 25000 + - 50000 + - 100000 + + vdd-supply: + description: Regulator that provides power to the sensor + + vddio-supply: + description: Regulator that provides power to the bus + +required: + - compatible + - reg + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@39 { + compatible = "amstaos,tsl2772"; + reg = <0x39>; + interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>; + vdd-supply = <&pm8941_l17>; + vddio-supply = <&pm8941_lvs1>; + amstaos,proximity-diodes = <0>; + led-max-microamp = <100000>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/mount-matrix.txt b/Documentation/devicetree/bindings/iio/mount-matrix.txt new file mode 100644 index 000000000000..c3344ab509a3 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/mount-matrix.txt @@ -0,0 +1,203 @@ +For discussion. Unclear are: +* is the definition of +/- values practical or counterintuitive? +* are the definitions unambiguous and easy to follow? +* are the examples correct? +* should we have HOWTO engineer a correct matrix for a new device (without comparing to a different one)? + +==== + + +Mounting matrix + +The mounting matrix is a device tree property used to orient any device +that produce three-dimensional data in relation to the world where it is +deployed. + +The purpose of the mounting matrix is to translate the sensor frame of +reference into the device frame of reference using a translation matrix as +defined in linear algebra. + +The typical usecase is that where a component has an internal representation +of the (x,y,z) triplets, such as different registers to read these coordinates, +and thus implying that the component should be mounted in a certain orientation +relative to some specific device frame of reference. + +For example a device with some kind of screen, where the user is supposed to +interact with the environment using an accelerometer, gyroscope or magnetometer +mounted on the same chassis as this screen, will likely take the screen as +reference to (x,y,z) orientation, with (x,y) corresponding to these axes on the +screen and (z) being depth, the axis perpendicular to the screen. + +For a screen you probably want (x) coordinates to go from negative on the left +to positive on the right, (y) from negative on the bottom to positive on top +and (z) depth to be negative under the screen and positive in front of it, +toward the face of the user. + +A sensor can be mounted in any angle along the axes relative to the frame of +reference. This means that the sensor may be flipped upside-down, left-right, +or tilted at any angle relative to the frame of reference. + +Another frame of reference is how the device with its sensor relates to the +external world, the environment where the device is deployed. Usually the data +from the sensor is used to figure out how the device is oriented with respect +to this world. When using the mounting matrix, the sensor and device orientation +becomes identical and we can focus on the data as it relates to the surrounding +world. + +Device-to-world examples for some three-dimensional sensor types: + +- Accelerometers have their world frame of reference toward the center of + gravity, usually to the core of the planet. A reading of the (x,y,z) values + from the sensor will give a projection of the gravity vector through the + device relative to the center of the planet, i.e. relative to its surface at + this point. Up and down in the world relative to the device frame of + reference can thus be determined. and users would likely expect a value of + 9.81 m/s^2 upwards along the (z) axis, i.e. out of the screen when the device + is held with its screen flat on the planets surface and 0 on the other axes, + as the gravity vector is projected 1:1 onto the sensors (z)-axis. + + If you tilt the device, the g vector virtually coming out of the display + is projected onto the (x,y) plane of the display panel. + + Example: + + ^ z: +g ^ z: > 0 + ! /! + ! x=y=0 / ! x: > 0 + +--------+ +--------+ + ! ! ! ! + +--------+ +--------+ + ! / + ! / + v v + center of center of + gravity gravity + + + If the device is tilted to the left, you get a positive x value. If you point + its top towards surface, you get a negative y axis. + + (---------) + ! ! y: -g + ! ! ^ + ! ! ! + ! ! + ! ! x: +g <- z: +g -> x: -g + ! 1 2 3 ! + ! 4 5 6 ! ! + ! 7 8 9 ! v + ! * 0 # ! y: +g + (---------) + + +- Magnetometers (compasses) have their world frame of reference relative to the + geomagnetic field. The system orientation vis-a-vis the world is defined with + respect to the local earth geomagnetic reference frame where (y) is in the + ground plane and positive towards magnetic North, (x) is in the ground plane, + perpendicular to the North axis and positive towards the East and (z) is + perpendicular to the ground plane and positive upwards. + + + ^^^ North: y > 0 + + (---------) + ! ! + ! ! + ! ! + ! ! > + ! ! > North: x > 0 + ! 1 2 3 ! > + ! 4 5 6 ! + ! 7 8 9 ! + ! * 0 # ! + (---------) + + Since the geomagnetic field is not uniform this definition fails if we come + closer to the poles. + + Sensors and driver can not and should not take care of this because there + are complex calculations and empirical data to be taken care of. We leave + this up to user space. + + The definition we take: + + If the device is placed at the equator and the top is pointing north, the + display is readable by a person standing upright on the earth surface, this + defines a positive y value. + + +- Gyroscopes detects the movement relative the device itself. The angular + velocity is defined as orthogonal to the plane of rotation, so if you put the + device on a flat surface and spin it around the z axis (such as rotating a + device with a screen lying flat on a table), you should get a negative value + along the (z) axis if rotated clockwise, and a positive value if rotated + counter-clockwise according to the right-hand rule. + + + (---------) y > 0 + ! ! v---\ + ! ! + ! ! + ! ! <--\ + ! ! ! z > 0 + ! 1 2 3 ! --/ + ! 4 5 6 ! + ! 7 8 9 ! + ! * 0 # ! + (---------) + + +So unless the sensor is ideally mounted, we need a means to indicate the +relative orientation of any given sensor of this type with respect to the +frame of reference. + +To achieve this, use the device tree property "mount-matrix" for the sensor. + +This supplies a 3x3 rotation matrix in the strict linear algebraic sense, +to orient the senor axes relative to a desired point of reference. This means +the resulting values from the sensor, after scaling to proper units, should be +multiplied by this matrix to give the proper vectors values in three-dimensional +space, relative to the device or world point of reference. + +For more information, consult: +https://en.wikipedia.org/wiki/Rotation_matrix + +The mounting matrix has the layout: + + (mxx, myx, mzx) + (mxy, myy, mzy) + (mxz, myz, mzz) + +Values are intended to be multiplied as: + + x' = mxx * x + myx * y + mzx * z + y' = mxy * x + myy * y + mzy * z + z' = mxz * x + myz * y + mzz * z + +It is represented as an array of strings containing the real values for +producing the transformation matrix. + +Examples: + +Identity matrix (nothing happens to the coordinates, which means the device was +mechanically mounted in an ideal way and we need no transformation): + +mount-matrix = "1", "0", "0", + "0", "1", "0", + "0", "0", "1"; + +The sensor is mounted 30 degrees (Pi/6 radians) tilted along the X axis, so we +compensate by performing a -30 degrees rotation around the X axis: + +mount-matrix = "1", "0", "0", + "0", "0.866", "0.5", + "0", "-0.5", "0.866"; + +The sensor is flipped 180 degrees (Pi radians) around the Z axis, i.e. mounted +upside-down: + +mount-matrix = "0.998", "0.054", "0", + "-0.054", "0.998", "0", + "0", "0", "1"; + +???: this does not match "180 degrees" - factors indicate ca. 3 degrees compensation diff --git a/Documentation/devicetree/bindings/iio/potentiometer/max5432.yaml b/Documentation/devicetree/bindings/iio/potentiometer/max5432.yaml new file mode 100644 index 000000000000..5082f919df2a --- /dev/null +++ b/Documentation/devicetree/bindings/iio/potentiometer/max5432.yaml @@ -0,0 +1,44 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/potentiometer/max5432.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim Integrated MAX5432-MAX5435 Digital Potentiometers + +maintainers: + - Martin Kaiser <martin@kaiser.cx> + +description: | + Maxim Integrated MAX5432-MAX5435 Digital Potentiometers connected via I2C + + Datasheet: + https://datasheets.maximintegrated.com/en/ds/MAX5432-MAX5435.pdf + +properties: + compatible: + enum: + - maxim,max5432 + - maxim,max5433 + - maxim,max5434 + - maxim,max5435 + + reg: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + max5434@28 { + compatible = "maxim,max5434"; + reg = <0x28>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/allwinner,sun4i-a10-lradc-keys.yaml b/Documentation/devicetree/bindings/input/allwinner,sun4i-a10-lradc-keys.yaml new file mode 100644 index 000000000000..b3bd8ef7fbd6 --- /dev/null +++ b/Documentation/devicetree/bindings/input/allwinner,sun4i-a10-lradc-keys.yaml @@ -0,0 +1,95 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/allwinner,sun4i-a10-lradc-keys.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 LRADC Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + compatible: + oneOf: + - const: allwinner,sun4i-a10-lradc-keys + - const: allwinner,sun8i-a83t-r-lradc + - items: + - const: allwinner,sun50i-a64-lradc + - const: allwinner,sun8i-a83t-r-lradc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + vref-supply: + description: + Regulator for the LRADC reference voltage + +patternProperties: + "^button-[0-9]+$": + type: object + properties: + label: + $ref: /schemas/types.yaml#/definitions/string + description: Descriptive name of the key + + linux,code: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Keycode to emit + + channel: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [0, 1] + description: ADC Channel this key is attached to + + voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Voltage in microvolts at LRADC input when this key is + pressed + + required: + - label + - linux,code + - channel + - voltage + + additionalProperties: false + +required: + - compatible + - reg + - interrupts + - vref-supply + +additionalProperties: false + +examples: + - | + lradc: lradc@1c22800 { + compatible = "allwinner,sun4i-a10-lradc-keys"; + reg = <0x01c22800 0x100>; + interrupts = <31>; + vref-supply = <®_vcc3v0>; + + button-191 { + label = "Volume Up"; + linux,code = <115>; + channel = <0>; + voltage = <191274>; + }; + + button-392 { + label = "Volume Down"; + linux,code = <114>; + channel = <0>; + voltage = <392644>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/input/elan_i2c.txt b/Documentation/devicetree/bindings/input/elan_i2c.txt index 797607460735..9963247706f2 100644 --- a/Documentation/devicetree/bindings/input/elan_i2c.txt +++ b/Documentation/devicetree/bindings/input/elan_i2c.txt @@ -13,9 +13,20 @@ Optional properties: pinctrl binding [1]). - vcc-supply: a phandle for the regulator supplying 3.3V power. - elan,trackpoint: touchpad can support a trackpoint (boolean) +- elan,clickpad: touchpad is a clickpad (the entire surface is a button) +- elan,middle-button: touchpad has a physical middle button +- elan,x_traces: number of antennas on the x axis +- elan,y_traces: number of antennas on the y axis +- some generic touchscreen properties [2]: + * touchscreen-size-x + * touchscreen-size-y + * touchscreen-x-mm + * touchscreen-y-mm + [0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt [1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt +[2]: Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt Example: &i2c1 { diff --git a/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt b/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt deleted file mode 100644 index 496125c6bfb7..000000000000 --- a/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt +++ /dev/null @@ -1,64 +0,0 @@ -Allwinner sun4i low res adc attached tablet keys ------------------------------------------------- - -Required properties: - - compatible: should be one of the following string: - "allwinner,sun4i-a10-lradc-keys" - "allwinner,sun8i-a83t-r-lradc" - - reg: mmio address range of the chip - - interrupts: interrupt to which the chip is connected - - vref-supply: powersupply for the lradc reference voltage - -Each key is represented as a sub-node of the compatible mentioned above: - -Required subnode-properties: - - label: Descriptive name of the key. - - linux,code: Keycode to emit. - - channel: Channel this key is attached to, must be 0 or 1. - - voltage: Voltage in µV at lradc input when this key is pressed. - -Example: - -#include <dt-bindings/input/input.h> - - lradc: lradc@1c22800 { - compatible = "allwinner,sun4i-a10-lradc-keys"; - reg = <0x01c22800 0x100>; - interrupts = <31>; - vref-supply = <®_vcc3v0>; - - button@191 { - label = "Volume Up"; - linux,code = <KEY_VOLUMEUP>; - channel = <0>; - voltage = <191274>; - }; - - button@392 { - label = "Volume Down"; - linux,code = <KEY_VOLUMEDOWN>; - channel = <0>; - voltage = <392644>; - }; - - button@601 { - label = "Menu"; - linux,code = <KEY_MENU>; - channel = <0>; - voltage = <601151>; - }; - - button@795 { - label = "Enter"; - linux,code = <KEY_ENTER>; - channel = <0>; - voltage = <795090>; - }; - - button@987 { - label = "Home"; - linux,code = <KEY_HOMEPAGE>; - channel = <0>; - voltage = <987387>; - }; - }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/ads7846.txt b/Documentation/devicetree/bindings/input/touchscreen/ads7846.txt index 04413da51391..81f6bda97d3c 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/ads7846.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/ads7846.txt @@ -32,7 +32,6 @@ Optional properties: (ADS7846). ti,keep-vref-on set to keep vref on for differential measurements as well - ti,swap-xy swap x and y axis ti,settle-delay-usec Settling time of the analog signals; a function of Vcc and the capacitance on the X/Y drivers. If set to non-zero, @@ -51,13 +50,6 @@ Optional properties: in Ohms (u16). ti,x-min Minimum value on the X axis (u16). ti,y-min Minimum value on the Y axis (u16). - ti,x-max Maximum value on the X axis (u16). - ti,y-max Minimum value on the Y axis (u16). - ti,pressure-min Minimum reported pressure value - (threshold) - u16. - ti,pressure-max Maximum reported pressure value (u16). - ti,debounce-max Max number of additional readings per - sample (u16). ti,debounce-tol Tolerance used for filtering (u16). ti,debounce-rep Additional consecutive good readings required after the first two (u16). @@ -67,7 +59,28 @@ Optional properties: line is connected to. wakeup-source use any event on touchscreen as wakeup event. (Legacy property support: "linux,wakeup") + touchscreen-size-x General touchscreen binding, see [1]. + touchscreen-size-y General touchscreen binding, see [1]. + touchscreen-max-pressure General touchscreen binding, see [1]. + touchscreen-min-pressure General touchscreen binding, see [1]. + touchscreen-average-samples General touchscreen binding, see [1]. + touchscreen-inverted-x General touchscreen binding, see [1]. + touchscreen-inverted-y General touchscreen binding, see [1]. + touchscreen-swapped-x-y General touchscreen binding, see [1]. + +[1] All general touchscreen properties are described in + Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt. +Deprecated properties: + + ti,swap-xy swap x and y axis + ti,x-max Maximum value on the X axis (u16). + ti,y-max Maximum value on the Y axis (u16). + ti,pressure-min Minimum reported pressure value + (threshold) - u16. + ti,pressure-max Maximum reported pressure value (u16). + ti,debounce-max Max number of additional readings per + sample (u16). Example for a TSC2046 chip connected to an McSPI controller of an OMAP SoC:: diff --git a/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt b/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt index 56d835242af2..da4c9d8b99b1 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt @@ -2,11 +2,24 @@ Required properties: - compatible : "rohm,bu21013_tp" - - reg : I2C device address + - reg : I2C device address + - reset-gpios : GPIO pin enabling (selecting) chip (CS) + - interrupt-parent : the phandle for the gpio controller + - interrupts : (gpio) interrupt to which the chip is connected Optional properties: - - touch-gpio : GPIO pin registering a touch event + - touch-gpios : GPIO pin registering a touch event - <supply_name>-supply : Phandle to a regulator supply + - touchscreen-size-x : General touchscreen binding, see [1]. + - touchscreen-size-y : General touchscreen binding, see [1]. + - touchscreen-inverted-x : General touchscreen binding, see [1]. + - touchscreen-inverted-y : General touchscreen binding, see [1]. + - touchscreen-swapped-x-y : General touchscreen binding, see [1]. + +[1] All general touchscreen properties are described in + Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt. + +Deprecated properties: - rohm,touch-max-x : Maximum outward permitted limit in the X axis - rohm,touch-max-y : Maximum outward permitted limit in the Y axis - rohm,flip-x : Flip touch coordinates on the X axis @@ -18,11 +31,13 @@ Example: bu21013_tp@5c { compatible = "rohm,bu21013_tp"; reg = <0x5c>; - touch-gpio = <&gpio2 20 0x4>; + interrupt-parent = <&gpio2>; + interrupts <&20 IRQ_TYPE_LEVEL_LOW>; + touch-gpio = <&gpio2 20 GPIO_ACTIVE_LOW>; avdd-supply = <&ab8500_ldo_aux1_reg>; - rohm,touch-max-x = <384>; - rohm,touch-max-y = <704>; - rohm,flip-y; + touchscreen-size-x = <384>; + touchscreen-size-y = <704>; + touchscreen-inverted-y; }; }; diff --git a/Documentation/devicetree/bindings/interconnect/qcom,qcs404.txt b/Documentation/devicetree/bindings/interconnect/qcom,qcs404.txt new file mode 100644 index 000000000000..c07d89812b73 --- /dev/null +++ b/Documentation/devicetree/bindings/interconnect/qcom,qcs404.txt @@ -0,0 +1,45 @@ +Qualcomm QCS404 Network-On-Chip interconnect driver binding +----------------------------------------------------------- + +Required properties : +- compatible : shall contain only one of the following: + "qcom,qcs404-bimc" + "qcom,qcs404-pcnoc" + "qcom,qcs404-snoc" +- #interconnect-cells : should contain 1 + +reg : specifies the physical base address and size of registers +clocks : list of phandles and specifiers to all interconnect bus clocks +clock-names : clock names should include both "bus" and "bus_a" + +Example: + +soc { + ... + bimc: interconnect@400000 { + reg = <0x00400000 0x80000>; + compatible = "qcom,qcs404-bimc"; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a"; + clocks = <&rpmcc RPM_SMD_BIMC_CLK>, + <&rpmcc RPM_SMD_BIMC_A_CLK>; + }; + + pnoc: interconnect@500000 { + reg = <0x00500000 0x15080>; + compatible = "qcom,qcs404-pcnoc"; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a"; + clocks = <&rpmcc RPM_SMD_PNOC_CLK>, + <&rpmcc RPM_SMD_PNOC_A_CLK>; + }; + + snoc: interconnect@580000 { + reg = <0x00580000 0x23080>; + compatible = "qcom,qcs404-snoc"; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a"; + clocks = <&rpmcc RPM_SMD_SNOC_CLK>, + <&rpmcc RPM_SMD_SNOC_A_CLK>; + }; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun4i-a10-ic.yaml b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun4i-a10-ic.yaml new file mode 100644 index 000000000000..23a202d24e43 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun4i-a10-ic.yaml @@ -0,0 +1,47 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/interrupt-controller/allwinner,sun4i-a10-ic.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 Interrupt Controller Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +allOf: + - $ref: /schemas/interrupt-controller.yaml# + +properties: + "#interrupt-cells": + const: 1 + + compatible: + enum: + - allwinner,sun4i-a10-ic + - allwinner,suniv-f1c100s-ic + + reg: + maxItems: 1 + + interrupt-controller: true + +required: + - "#interrupt-cells" + - compatible + - reg + - interrupt-controller + +additionalProperties: false + +examples: + - | + intc: interrupt-controller@1c20400 { + compatible = "allwinner,sun4i-a10-ic"; + reg = <0x01c20400 0x400>; + interrupt-controller; + #interrupt-cells = <1>; + }; + +... diff --git a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun4i-ic.txt b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun4i-ic.txt deleted file mode 100644 index 404352524c3a..000000000000 --- a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun4i-ic.txt +++ /dev/null @@ -1,20 +0,0 @@ -Allwinner Sunxi Interrupt Controller - -Required properties: - -- compatible : should be one of the following: - "allwinner,sun4i-a10-ic" - "allwinner,suniv-f1c100s-ic" -- reg : Specifies base physical address and size of the registers. -- interrupt-controller : Identifies the node as an interrupt controller -- #interrupt-cells : Specifies the number of cells needed to encode an - interrupt source. The value shall be 1. - -Example: - -intc: interrupt-controller { - compatible = "allwinner,sun4i-a10-ic"; - reg = <0x01c20400 0x400>; - interrupt-controller; - #interrupt-cells = <1>; -}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml new file mode 100644 index 000000000000..0eccf5551786 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml @@ -0,0 +1,70 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A20 Non-Maskable Interrupt Controller Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +allOf: + - $ref: /schemas/interrupt-controller.yaml# + +properties: + "#interrupt-cells": + const: 2 + description: + The first cell is the IRQ number, the second cell the trigger + type as defined in interrupt.txt in this directory. + + compatible: + oneOf: + - const: allwinner,sun6i-a31-r-intc + - const: allwinner,sun6i-a31-sc-nmi + deprecated: true + - const: allwinner,sun7i-a20-sc-nmi + - items: + - const: allwinner,sun8i-a83t-r-intc + - const: allwinner,sun6i-a31-r-intc + - const: allwinner,sun9i-a80-sc-nmi + - items: + - const: allwinner,sun50i-a64-r-intc + - const: allwinner,sun6i-a31-r-intc + - items: + - const: allwinner,sun50i-h6-r-intc + - const: allwinner,sun6i-a31-r-intc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + interrupt-controller: true + +required: + - "#interrupt-cells" + - compatible + - reg + - interrupts + - interrupt-controller + +# FIXME: We should set it, but it would report all the generic +# properties as additional properties. +# additionalProperties: false + +examples: + - | + interrupt-controller@1c00030 { + compatible = "allwinner,sun7i-a20-sc-nmi"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x01c00030 0x0c>; + interrupt-parent = <&gic>; + interrupts = <0 0 4>; + }; + +... diff --git a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sunxi-nmi.txt b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sunxi-nmi.txt deleted file mode 100644 index 24beadf7ba83..000000000000 --- a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sunxi-nmi.txt +++ /dev/null @@ -1,29 +0,0 @@ -Allwinner Sunxi NMI Controller -============================== - -Required properties: - -- compatible : should be one of the following: - - "allwinner,sun7i-a20-sc-nmi" - - "allwinner,sun6i-a31-sc-nmi" (deprecated) - - "allwinner,sun6i-a31-r-intc" - - "allwinner,sun9i-a80-nmi" -- reg : Specifies base physical address and size of the registers. -- interrupt-controller : Identifies the node as an interrupt controller -- #interrupt-cells : Specifies the number of cells needed to encode an - interrupt source. The value shall be 2. The first cell is the IRQ number, the - second cell the trigger type as defined in interrupt.txt in this directory. -- interrupts: Specifies the interrupt line (NMI) which is handled by - the interrupt controller in the parent controller's notation. This value - shall be the NMI. - -Example: - -sc-nmi-intc@1c00030 { - compatible = "allwinner,sun7i-a20-sc-nmi"; - interrupt-controller; - #interrupt-cells = <2>; - reg = <0x01c00030 0x0c>; - interrupt-parent = <&gic>; - interrupts = <0 0 4>; -}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/amazon,al-fic.txt b/Documentation/devicetree/bindings/interrupt-controller/amazon,al-fic.txt new file mode 100644 index 000000000000..c676b03c752e --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/amazon,al-fic.txt @@ -0,0 +1,27 @@ +Amazon's Annapurna Labs Fabric Interrupt Controller + +Required properties: + +- compatible: should be "amazon,al-fic" +- reg: physical base address and size of the registers +- interrupt-controller: identifies the node as an interrupt controller +- #interrupt-cells : must be 2. Specifies the number of cells needed to encode + an interrupt source. Supported trigger types are low-to-high edge + triggered and active high level-sensitive. +- interrupts: describes which input line in the interrupt parent, this + fic's output is connected to. This field property depends on the parent's + binding + +Please refer to interrupts.txt in this directory for details of the common +Interrupt Controllers bindings used by client devices. + +Example: + +amazon_fic: interrupt-controller@fd8a8500 { + compatible = "amazon,al-fic"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x0 0xfd8a8500 0x0 0x1000>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 0x0 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt index 1502a51548bb..684bb1cd75ec 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt @@ -15,6 +15,8 @@ Required properties: "amlogic,meson-gxbb-gpio-intc" for GXBB SoCs (S905) or "amlogic,meson-gxl-gpio-intc" for GXL SoCs (S905X, S912) "amlogic,meson-axg-gpio-intc" for AXG SoCs (A113D, A113X) + "amlogic,meson-g12a-gpio-intc" for G12A SoCs (S905D2, S905X2, S905Y2) + "amlogic,meson-sm1-gpio-intc" for SM1 SoCs (S905D3, S905X3, S905Y3) - reg : Specifies base physical address and size of the registers. - interrupt-controller : Identifies the node as an interrupt controller. - #interrupt-cells : Specifies the number of cells needed to encode an diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.yaml b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.yaml index c34df35a25fc..1fe147daca4c 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.yaml +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.yaml @@ -44,11 +44,13 @@ properties: be at least 4. The 1st cell is the interrupt type; 0 for SPI interrupts, 1 for PPI - interrupts. Other values are reserved for future use. + interrupts, 2 for interrupts in the Extended SPI range, 3 for the + Extended PPI range. Other values are reserved for future use. The 2nd cell contains the interrupt number for the interrupt type. SPI interrupts are in the range [0-987]. PPI interrupts are in the - range [0-15]. + range [0-15]. Extented SPI interrupts are in the range [0-1023]. + Extended PPI interrupts are in the range [0-127]. The 3rd cell is the flags, encoded as follows: bits[3:0] trigger type and level flags. diff --git a/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt b/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt index ab921f1698fb..e13405355166 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt @@ -6,11 +6,16 @@ C-SKY Multi-processors Interrupt Controller is designed for ck807/ck810/ck860 SMP soc, and it also could be used in non-SMP system. Interrupt number definition: - 0-15 : software irq, and we use 15 as our IPI_IRQ. 16-31 : private irq, and we use 16 as the co-processor timer. 31-1024: common irq for soc ip. +Interrupt triger mode: (Defined in dt-bindings/interrupt-controller/irq.h) + IRQ_TYPE_LEVEL_HIGH (default) + IRQ_TYPE_LEVEL_LOW + IRQ_TYPE_EDGE_RISING + IRQ_TYPE_EDGE_FALLING + ============================= intc node bindings definition ============================= @@ -26,15 +31,22 @@ intc node bindings definition - #interrupt-cells Usage: required Value type: <u32> - Definition: must be <1> + Definition: <2> - interrupt-controller: Usage: required -Examples: +Examples: ("interrupts = <irq_num IRQ_TYPE_XXX>") --------- +#include <dt-bindings/interrupt-controller/irq.h> intc: interrupt-controller { compatible = "csky,mpintc"; - #interrupt-cells = <1>; + #interrupt-cells = <2>; interrupt-controller; }; + + device: device-example { + ... + interrupts = <34 IRQ_TYPE_EDGE_RISING>; + interrupt-parent = <&intc>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/intel,ixp4xx-interrupt.yaml b/Documentation/devicetree/bindings/interrupt-controller/intel,ixp4xx-interrupt.yaml index bae10e261fa9..507c141ea760 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/intel,ixp4xx-interrupt.yaml +++ b/Documentation/devicetree/bindings/interrupt-controller/intel,ixp4xx-interrupt.yaml @@ -2,7 +2,7 @@ # Copyright 2018 Linaro Ltd. %YAML 1.2 --- -$id: "http://devicetree.org/schemas/interrupt/intel-ixp4xx-interrupt.yaml#" +$id: "http://devicetree.org/schemas/interrupt-controller/intel,ixp4xx-interrupt.yaml#" $schema: "http://devicetree.org/meta-schemas/core.yaml#" title: Intel IXP4xx XScale Networking Processors Interrupt Controller diff --git a/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt b/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt index 8a3c40829899..4a3ee253f7f0 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt @@ -22,10 +22,10 @@ controller node. This property is inherited, so it may be specified in an interrupt client node or in any of its parent nodes. Interrupts listed in the "interrupts" property are always in reference to the node's interrupt parent. -The "interrupts-extended" property is a special form for use when a node needs -to reference multiple interrupt parents. Each entry in this property contains -both the parent phandle and the interrupt specifier. "interrupts-extended" -should only be used when a device has multiple interrupt parents. +The "interrupts-extended" property is a special form; useful when a node needs +to reference multiple interrupt parents or a different interrupt parent than +the inherited one. Each entry in this property contains both the parent phandle +and the interrupt specifier. Example: interrupts-extended = <&intc1 5 1>, <&intc2 1 0>; diff --git a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt index 0e312fea2a5d..84ced3f4179b 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt @@ -15,6 +15,7 @@ Required properties: "mediatek,mt7629-sysirq", "mediatek,mt6577-sysirq": for MT7629 "mediatek,mt6795-sysirq", "mediatek,mt6577-sysirq": for MT6795 "mediatek,mt6797-sysirq", "mediatek,mt6577-sysirq": for MT6797 + "mediatek,mt6779-sysirq", "mediatek,mt6577-sysirq": for MT6779 "mediatek,mt6765-sysirq", "mediatek,mt6577-sysirq": for MT6765 "mediatek,mt6755-sysirq", "mediatek,mt6577-sysirq": for MT6755 "mediatek,mt6592-sysirq", "mediatek,mt6577-sysirq": for MT6592 diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,rza1-irqc.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,rza1-irqc.txt new file mode 100644 index 000000000000..727b7e4cd6e0 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,rza1-irqc.txt @@ -0,0 +1,43 @@ +DT bindings for the Renesas RZ/A1 Interrupt Controller + +The RZ/A1 Interrupt Controller is a front-end for the GIC found on Renesas +RZ/A1 and RZ/A2 SoCs: + - IRQ sense select for 8 external interrupts, 1:1-mapped to 8 GIC SPI + interrupts, + - NMI edge select. + +Required properties: + - compatible: Must be "renesas,<soctype>-irqc", and "renesas,rza1-irqc" as + fallback. + Examples with soctypes are: + - "renesas,r7s72100-irqc" (RZ/A1H) + - "renesas,r7s9210-irqc" (RZ/A2M) + - #interrupt-cells: Must be 2 (an interrupt index and flags, as defined + in interrupts.txt in this directory) + - #address-cells: Must be zero + - interrupt-controller: Marks the device as an interrupt controller + - reg: Base address and length of the memory resource used by the interrupt + controller + - interrupt-map: Specifies the mapping from external interrupts to GIC + interrupts + - interrupt-map-mask: Must be <7 0> + +Example: + + irqc: interrupt-controller@fcfef800 { + compatible = "renesas,r7s72100-irqc", "renesas,rza1-irqc"; + #interrupt-cells = <2>; + #address-cells = <0>; + interrupt-controller; + reg = <0xfcfef800 0x6>; + interrupt-map = + <0 0 &gic GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, + <1 0 &gic GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>, + <2 0 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>, + <3 0 &gic GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <4 0 &gic GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, + <5 0 &gic GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>, + <6 0 &gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, + <7 0 &gic GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + interrupt-map-mask = <7 0>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/snps,archs-idu-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/snps,archs-idu-intc.txt index 09fc02b99845..a5c1db95b3ec 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/snps,archs-idu-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/snps,archs-idu-intc.txt @@ -1,20 +1,30 @@ * ARC-HS Interrupt Distribution Unit - This optional 2nd level interrupt controller can be used in SMP configurations for - dynamic IRQ routing, load balancing of common/external IRQs towards core intc. + This optional 2nd level interrupt controller can be used in SMP configurations + for dynamic IRQ routing, load balancing of common/external IRQs towards core + intc. Properties: - compatible: "snps,archs-idu-intc" - interrupt-controller: This is an interrupt controller. -- #interrupt-cells: Must be <1>. - - Value of the cell specifies the "common" IRQ from peripheral to IDU. Number N - of the particular interrupt line of IDU corresponds to the line N+24 of the - core interrupt controller. - - intc accessed via the special ARC AUX register interface, hence "reg" property - is not specified. +- #interrupt-cells: Must be <1> or <2>. + + Value of the first cell specifies the "common" IRQ from peripheral to IDU. + Number N of the particular interrupt line of IDU corresponds to the line N+24 + of the core interrupt controller. + + The (optional) second cell specifies any of the following flags: + - bits[3:0] trigger type and level flags + 1 = low-to-high edge triggered + 2 = NOT SUPPORTED (high-to-low edge triggered) + 4 = active high level-sensitive <<< DEFAULT + 8 = NOT SUPPORTED (active low level-sensitive) + When no second cell is specified, the interrupt is assumed to be level + sensitive. + + The interrupt controller is accessed via the special ARC AUX register + interface, hence "reg" property is not specified. Example: core_intc: core-interrupt-controller { diff --git a/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt b/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt index 6922db598def..ce59a505f5a4 100644 --- a/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt +++ b/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt @@ -11,10 +11,23 @@ ARM Short-Descriptor translation table format for address translation. | m4u (Multimedia Memory Management Unit) | + +--------+ + | | + gals0-rx gals1-rx (Global Async Local Sync rx) + | | + | | + gals0-tx gals1-tx (Global Async Local Sync tx) + | | Some SoCs may have GALS. + +--------+ + | SMI Common(Smart Multimedia Interface Common) | +----------------+------- | | + | gals-rx There may be GALS in some larbs. + | | + | | + | gals-tx | | SMI larb0 SMI larb1 ... SoCs have several SMI local arbiter(larb). (display) (vdec) @@ -36,6 +49,10 @@ each local arbiter. like display, video decode, and camera. And there are different ports in each larb. Take a example, There are many ports like MC, PP, VLD in the video decode local arbiter, all these ports are according to the video HW. + In some SoCs, there may be a GALS(Global Async Local Sync) module between +smi-common and m4u, and additional GALS module between smi-larb and +smi-common. GALS can been seen as a "asynchronous fifo" which could help +synchronize for the modules in different clock frequency. Required properties: - compatible : must be one of the following string: @@ -44,18 +61,25 @@ Required properties: "mediatek,mt7623-m4u", "mediatek,mt2701-m4u" for mt7623 which uses generation one m4u HW. "mediatek,mt8173-m4u" for mt8173 which uses generation two m4u HW. + "mediatek,mt8183-m4u" for mt8183 which uses generation two m4u HW. - reg : m4u register base and size. - interrupts : the interrupt of m4u. - clocks : must contain one entry for each clock-names. -- clock-names : must be "bclk", It is the block clock of m4u. +- clock-names : Only 1 optional clock: + - "bclk": the block clock of m4u. + Here is the list which require this "bclk": + - mt2701, mt2712, mt7623 and mt8173. + Note that m4u use the EMI clock which always has been enabled before kernel + if there is no this "bclk". - mediatek,larbs : List of phandle to the local arbiters in the current Socs. Refer to bindings/memory-controllers/mediatek,smi-larb.txt. It must sort according to the local arbiter index, like larb0, larb1, larb2... - iommu-cells : must be 1. This is the mtk_m4u_id according to the HW. Specifies the mtk_m4u_id as defined in dt-binding/memory/mt2701-larb-port.h for mt2701, mt7623 - dt-binding/memory/mt2712-larb-port.h for mt2712, and - dt-binding/memory/mt8173-larb-port.h for mt8173. + dt-binding/memory/mt2712-larb-port.h for mt2712, + dt-binding/memory/mt8173-larb-port.h for mt8173, and + dt-binding/memory/mt8183-larb-port.h for mt8183. Example: iommu: iommu@10205000 { diff --git a/Documentation/devicetree/bindings/ipmi/npcm7xx-kcs-bmc.txt b/Documentation/devicetree/bindings/ipmi/npcm7xx-kcs-bmc.txt index 3538a214fff1..352f5e9c759b 100644 --- a/Documentation/devicetree/bindings/ipmi/npcm7xx-kcs-bmc.txt +++ b/Documentation/devicetree/bindings/ipmi/npcm7xx-kcs-bmc.txt @@ -36,4 +36,4 @@ Example: kcs_chan = <2>; status = "disabled"; }; - };
\ No newline at end of file + }; diff --git a/Documentation/devicetree/bindings/leds/ams,as3645a.txt b/Documentation/devicetree/bindings/leds/ams,as3645a.txt index fdc40e354a64..4af2987b25e9 100644 --- a/Documentation/devicetree/bindings/leds/ams,as3645a.txt +++ b/Documentation/devicetree/bindings/leds/ams,as3645a.txt @@ -39,7 +39,9 @@ ams,input-max-microamp: Maximum flash controller input current. The Optional properties of the flash child node =========================================== -label : The label of the flash LED. +function : See Documentation/devicetree/bindings/leds/common.txt. +color : See Documentation/devicetree/bindings/leds/common.txt. +label : See Documentation/devicetree/bindings/leds/common.txt (deprecated). Required properties of the indicator child node (1) @@ -52,28 +54,32 @@ led-max-microamp: Maximum indicator current. The allowed values are Optional properties of the indicator child node =============================================== -label : The label of the indicator LED. +function : See Documentation/devicetree/bindings/leds/common.txt. +color : See Documentation/devicetree/bindings/leds/common.txt. +label : See Documentation/devicetree/bindings/leds/common.txt (deprecated). Example ======= +#include <dt-bindings/leds/common.h> + as3645a@30 { - #address-cells: 1 - #size-cells: 0 + #address-cells = <1>; + #size-cells = <0>; reg = <0x30>; compatible = "ams,as3645a"; - flash@0 { + led@0 { reg = <0x0>; flash-timeout-us = <150000>; flash-max-microamp = <320000>; led-max-microamp = <60000>; ams,input-max-microamp = <1750000>; - label = "as3645a:flash"; + function = LED_FUNCTION_FLASH; }; - indicator@1 { + led@1 { reg = <0x1>; led-max-microamp = <10000>; - label = "as3645a:indicator"; + function = LED_FUNCTION_INDICATOR; }; }; diff --git a/Documentation/devicetree/bindings/leds/backlight/lm3630a-backlight.yaml b/Documentation/devicetree/bindings/leds/backlight/lm3630a-backlight.yaml index 4d61fe0a98a4..dc129d9a329e 100644 --- a/Documentation/devicetree/bindings/leds/backlight/lm3630a-backlight.yaml +++ b/Documentation/devicetree/bindings/leds/backlight/lm3630a-backlight.yaml @@ -23,16 +23,17 @@ properties: reg: maxItems: 1 - ti,linear-mapping-mode: - description: | - Enable linear mapping mode. If disabled, then it will use exponential - mapping mode in which the ramp up/down appears to have a more uniform - transition to the human eye. - type: boolean + '#address-cells': + const: 1 + + '#size-cells': + const: 0 required: - compatible - reg + - '#address-cells' + - '#size-cells' patternProperties: "^led@[01]$": @@ -48,7 +49,6 @@ patternProperties: in this property. The two current sinks can be controlled independently with both banks, or bank A can be configured to control both sinks with the led-sources property. - maxItems: 1 minimum: 0 maximum: 1 @@ -73,6 +73,13 @@ patternProperties: minimum: 0 maximum: 255 + ti,linear-mapping-mode: + description: | + Enable linear mapping mode. If disabled, then it will use exponential + mapping mode in which the ramp up/down appears to have a more uniform + transition to the human eye. + type: boolean + required: - reg diff --git a/Documentation/devicetree/bindings/leds/common.txt b/Documentation/devicetree/bindings/leds/common.txt index 70876ac11367..9fa6f9795d50 100644 --- a/Documentation/devicetree/bindings/leds/common.txt +++ b/Documentation/devicetree/bindings/leds/common.txt @@ -10,14 +10,30 @@ can influence the way of the LED device initialization, the LED components have to be tightly coupled with the LED device binding. They are represented by child nodes of the parent LED device binding. + Optional properties for child nodes: - led-sources : List of device current outputs the LED is connected to. The outputs are identified by the numbers that must be defined in the LED device binding documentation. + +- function: LED functon. Use one of the LED_FUNCTION_* prefixed definitions + from the header include/dt-bindings/leds/common.h. + If there is no matching LED_FUNCTION available, add a new one. + +- color : Color of the LED. Use one of the LED_COLOR_ID_* prefixed definitions + from the header include/dt-bindings/leds/common.h. + If there is no matching LED_COLOR_ID available, add a new one. + +- function-enumerator: Integer to be used when more than one instance + of the same function is needed, differing only with + an ordinal number. + - label : The label for this LED. If omitted, the label is taken from the node name (excluding the unit address). It has to uniquely identify a device, i.e. no other LED class device can be assigned the same - label. + label. This property is deprecated - use 'function' and 'color' + properties instead. function-enumerator has no effect when this + property is present. - default-state : The initial state of the LED. Valid values are "on", "off", and "keep". If the LED is already on or off and the default-state property is @@ -99,29 +115,59 @@ Required properties for trigger source: * Examples -gpio-leds { +#include <dt-bindings/leds/common.h> + +led-controller@0 { compatible = "gpio-leds"; - system-status { - label = "Status"; + led0 { + function = LED_FUNCTION_STATUS; linux,default-trigger = "heartbeat"; gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; }; - usb { + led1 { + function = LED_FUNCTION_USB; gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>; trigger-sources = <&ohci_port1>, <&ehci_port1>; }; }; -max77693-led { +led-controller@0 { compatible = "maxim,max77693-led"; - camera-flash { - label = "Flash"; + led { + function = LED_FUNCTION_FLASH; + color = <LED_COLOR_ID_WHITE>; led-sources = <0>, <1>; led-max-microamp = <50000>; flash-max-microamp = <320000>; flash-max-timeout-us = <500000>; }; }; + +led-controller@30 { + compatible = "panasonic,an30259a"; + reg = <0x30>; + #address-cells = <1>; + #size-cells = <0>; + + led@1 { + reg = <1>; + linux,default-trigger = "heartbeat"; + function = LED_FUNCTION_INDICATOR; + function-enumerator = <1>; + }; + + led@2 { + reg = <2>; + function = LED_FUNCTION_INDICATOR; + function-enumerator = <2>; + }; + + led@3 { + reg = <3>; + function = LED_FUNCTION_INDICATOR; + function-enumerator = <3>; + }; +}; diff --git a/Documentation/devicetree/bindings/leds/leds-aat1290.txt b/Documentation/devicetree/bindings/leds/leds-aat1290.txt index 85c0c58617f6..62ed17ec075b 100644 --- a/Documentation/devicetree/bindings/leds/leds-aat1290.txt +++ b/Documentation/devicetree/bindings/leds/leds-aat1290.txt @@ -32,15 +32,18 @@ Required properties of the LED child node: formula: T = 8.82 * 10^9 * Ct. Optional properties of the LED child node: -- label : see Documentation/devicetree/bindings/leds/common.txt +- function : see Documentation/devicetree/bindings/leds/common.txt +- color : see Documentation/devicetree/bindings/leds/common.txt +- label : see Documentation/devicetree/bindings/leds/common.txt (deprecated) Example (by Ct = 220nF, Rset = 160kohm and exynos4412-trats2 board with a switch that allows for routing strobe signal either from the host or from the camera sensor): #include "exynos4412.dtsi" +#include <dt-bindings/leds/common.h> -aat1290 { +led-controller { compatible = "skyworks,aat1290"; flen-gpios = <&gpj1 1 GPIO_ACTIVE_HIGH>; enset-gpios = <&gpj1 2 GPIO_ACTIVE_HIGH>; @@ -50,8 +53,9 @@ aat1290 { pinctrl-1 = <&camera_flash_host>; pinctrl-2 = <&camera_flash_isp>; - camera_flash: flash-led { - label = "aat1290-flash"; + camera_flash: led { + function = LED_FUNCTION_FLASH; + color = <LED_COLOR_ID_WHITE>; led-max-microamp = <520833>; flash-max-microamp = <1012500>; flash-max-timeout-us = <1940000>; diff --git a/Documentation/devicetree/bindings/leds/leds-an30259a.txt b/Documentation/devicetree/bindings/leds/leds-an30259a.txt index 6ffb861083c0..cbd833906b2b 100644 --- a/Documentation/devicetree/bindings/leds/leds-an30259a.txt +++ b/Documentation/devicetree/bindings/leds/leds-an30259a.txt @@ -15,10 +15,19 @@ Required sub-node properties: - reg: Pin that the LED is connected to. Must be 1, 2, or 3. Optional sub-node properties: - - label: see Documentation/devicetree/bindings/leds/common.txt - - linux,default-trigger: see Documentation/devicetree/bindings/leds/common.txt + - function : + see Documentation/devicetree/bindings/leds/common.txt + - color : + see Documentation/devicetree/bindings/leds/common.txt + - label : + see Documentation/devicetree/bindings/leds/common.txt (deprecated) + - linux,default-trigger : + see Documentation/devicetree/bindings/leds/common.txt Example: + +#include <dt-bindings/leds/common.h> + led-controller@30 { compatible = "panasonic,an30259a"; reg = <0x30>; @@ -28,16 +37,19 @@ led-controller@30 { led@1 { reg = <1>; linux,default-trigger = "heartbeat"; - label = "red:indicator"; + function = LED_FUNCTION_INDICATOR; + color = <LED_COLOR_ID_RED>; }; led@2 { reg = <2>; - label = "green:indicator"; + function = LED_FUNCTION_INDICATOR; + color = <LED_COLOR_ID_GREEN>; }; led@3 { reg = <3>; - label = "blue:indicator"; + function = LED_FUNCTION_INDICATOR; + color = <LED_COLOR_ID_BLUE>; }; }; diff --git a/Documentation/devicetree/bindings/leds/leds-cr0014114.txt b/Documentation/devicetree/bindings/leds/leds-cr0014114.txt index 4255b19ad25c..f8de7516a39b 100644 --- a/Documentation/devicetree/bindings/leds/leds-cr0014114.txt +++ b/Documentation/devicetree/bindings/leds/leds-cr0014114.txt @@ -11,14 +11,20 @@ Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt apply. In particular, "reg" and "spi-max-frequency" properties must be given. LED sub-node properties: -- label : +- function : + see Documentation/devicetree/bindings/leds/common.txt +- color : see Documentation/devicetree/bindings/leds/common.txt +- label : + see Documentation/devicetree/bindings/leds/common.txt (deprecated) - linux,default-trigger : (optional) see Documentation/devicetree/bindings/leds/common.txt Example ------- +#include <dt-bindings/leds/common.h> + led-controller@0 { compatible = "crane,cr0014114"; reg = <0>; @@ -28,27 +34,33 @@ led-controller@0 { led@0 { reg = <0>; - label = "red:coin"; + function = "coin"; + color = <LED_COLOR_ID_RED>; }; led@1 { reg = <1>; - label = "green:coin"; + function = "coin"; + color = <LED_COLOR_ID_GREEN>; }; led@2 { reg = <2>; - label = "blue:coin"; + function = "coin"; + color = <LED_COLOR_ID_BLUE>; }; led@3 { reg = <3>; - label = "red:bill"; + function = "bill"; + color = <LED_COLOR_ID_RED>; }; led@4 { reg = <4>; - label = "green:bill"; + function = "bill"; + color = <LED_COLOR_ID_GREEN>; }; led@5 { reg = <5>; - label = "blue:bill"; + function = "bill"; + color = <LED_COLOR_ID_BLUE>; }; ... }; diff --git a/Documentation/devicetree/bindings/leds/leds-gpio.txt b/Documentation/devicetree/bindings/leds/leds-gpio.txt index a48dda268f81..d21281b63d38 100644 --- a/Documentation/devicetree/bindings/leds/leds-gpio.txt +++ b/Documentation/devicetree/bindings/leds/leds-gpio.txt @@ -10,8 +10,12 @@ LED sub-node properties: - gpios : Should specify the LED's GPIO, see "gpios property" in Documentation/devicetree/bindings/gpio/gpio.txt. Active low LEDs should be indicated using flags in the GPIO specifier. -- label : (optional) +- function : (optional) + see Documentation/devicetree/bindings/leds/common.txt +- color : (optional) see Documentation/devicetree/bindings/leds/common.txt +- label : (optional) + see Documentation/devicetree/bindings/leds/common.txt (deprecated) - linux,default-trigger : (optional) see Documentation/devicetree/bindings/leds/common.txt - default-state: (optional) The initial state of the LED. @@ -27,30 +31,34 @@ LED sub-node properties: Examples: #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> leds { compatible = "gpio-leds"; - hdd { - label = "Disk Activity"; + led0 { gpios = <&mcu_pio 0 GPIO_ACTIVE_LOW>; linux,default-trigger = "disk-activity"; + function = LED_FUNCTION_DISK; }; - fault { + led1 { gpios = <&mcu_pio 1 GPIO_ACTIVE_HIGH>; /* Keep LED on if BIOS detected hardware fault */ default-state = "keep"; + function = LED_FUNCTION_FAULT; }; }; run-control { compatible = "gpio-leds"; - red { + led0 { gpios = <&mpc8572 6 GPIO_ACTIVE_HIGH>; + color = <LED_COLOR_ID_RED>; default-state = "off"; }; - green { + led1 { gpios = <&mpc8572 7 GPIO_ACTIVE_HIGH>; + color = <LED_COLOR_ID_GREEN>; default-state = "on"; }; }; @@ -58,9 +66,10 @@ run-control { leds { compatible = "gpio-leds"; - charger-led { + led0 { gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; linux,default-trigger = "max8903-charger-charging"; retain-state-suspended; + function = LED_FUNCTION_CHARGE; }; }; diff --git a/Documentation/devicetree/bindings/leds/leds-lm3532.txt b/Documentation/devicetree/bindings/leds/leds-lm3532.txt index c087f85ddddc..53793213dd52 100644 --- a/Documentation/devicetree/bindings/leds/leds-lm3532.txt +++ b/Documentation/devicetree/bindings/leds/leds-lm3532.txt @@ -62,6 +62,9 @@ Optional LED child properties: - label : see Documentation/devicetree/bindings/leds/common.txt - linux,default-trigger : see Documentation/devicetree/bindings/leds/common.txt + - led-max-microamp : Defines the full scale current value for each control + bank. The range is from 5000uA-29800uA in increments + of 800uA. Example: led-controller@38 { @@ -85,6 +88,7 @@ led-controller@38 { reg = <0>; led-sources = <2>; ti,led-mode = <1>; + led-max-microamp = <21800>; label = ":backlight"; linux,default-trigger = "backlight"; }; diff --git a/Documentation/devicetree/bindings/leds/leds-lm3601x.txt b/Documentation/devicetree/bindings/leds/leds-lm3601x.txt index a88b2c41e75b..095dafb6ec7f 100644 --- a/Documentation/devicetree/bindings/leds/leds-lm3601x.txt +++ b/Documentation/devicetree/bindings/leds/leds-lm3601x.txt @@ -22,9 +22,14 @@ Required properties for flash LED child nodes: - led-max-microamp : Range from 2.4mA - 376mA Optional child properties: - - label : see Documentation/devicetree/bindings/leds/common.txt + - function : see Documentation/devicetree/bindings/leds/common.txt + - color : see Documentation/devicetree/bindings/leds/common.txt + - label : see Documentation/devicetree/bindings/leds/common.txt (deprecated) Example: + +#include <dt-bindings/leds/common.h> + led-controller@64 { compatible = "ti,lm36010"; #address-cells = <1>; @@ -33,7 +38,8 @@ led-controller@64 { led@0 { reg = <1>; - label = "white:torch"; + function = LED_FUNCTION_TORCH; + color = <LED_COLOR_ID_WHITE>; led-max-microamp = <376000>; flash-max-microamp = <1500000>; flash-max-timeout-us = <1600000>; diff --git a/Documentation/devicetree/bindings/leds/leds-lm36274.txt b/Documentation/devicetree/bindings/leds/leds-lm36274.txt new file mode 100644 index 000000000000..39c230d59a4d --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-lm36274.txt @@ -0,0 +1,85 @@ +* Texas Instruments LM36274 4-Channel LCD Backlight Driver w/Integrated Bias + +The LM36274 is an integrated four-channel WLED driver and LCD bias supply. +The backlight boost provides the power to bias four parallel LED strings with +up to 29V total output voltage. The 11-bit LED current is programmable via +the I2C bus and/or controlled via a logic level PWM input from 60 uA to 30 mA. + +Parent device properties are documented in +Documentation/devicetree/bindings/mfd/ti-lmu.txt + +Regulator properties are documented in +Documentation/devicetree/bindings/regulator/lm363x-regulator.txt + +Required backlight properties: + - compatible: + "ti,lm36274-backlight" + - reg : 0 + - #address-cells : 1 + - #size-cells : 0 + - led-sources : Indicates which LED strings will be enabled. + Values from 0-3, sources is 0 based so strings will be + source value + 1. + +Optional backlight properties: + - label : see Documentation/devicetree/bindings/leds/common.txt + - linux,default-trigger : + see Documentation/devicetree/bindings/leds/common.txt + +Example: + +HVLED string 1 and 3 are controlled by control bank A and HVLED 2 string is +controlled by control bank B. + +lm36274@11 { + compatible = "ti,lm36274"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11>; + + enable-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; + + regulators { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,lm363x-regulator"; + + enable-gpios = <&pioC 0 GPIO_ACTIVE_HIGH>, + <&pioC 1 GPIO_ACTIVE_HIGH>; + + vboost { + regulator-name = "lcd_boost"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <7150000>; + regulator-always-on; + }; + + vpos { + regulator-name = "lcd_vpos"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6500000>; + }; + + vneg { + regulator-name = "lcd_vneg"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6500000>; + }; + }; + + backlight { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,lm36274-backlight"; + + led@0 { + reg = <0>; + led-sources = <0 2>; + label = "white:backlight_cluster"; + linux,default-trigger = "backlight"; + }; + }; +}; + +For more product information please see the link below: +http://www.ti.com/lit/ds/symlink/lm36274.pdf diff --git a/Documentation/devicetree/bindings/leds/leds-lm3692x.txt b/Documentation/devicetree/bindings/leds/leds-lm3692x.txt index 08b352840bd7..4c2d923f8758 100644 --- a/Documentation/devicetree/bindings/leds/leds-lm3692x.txt +++ b/Documentation/devicetree/bindings/leds/leds-lm3692x.txt @@ -26,12 +26,16 @@ Required child properties: 3 - Will enable the LED3 sync (LM36923 only) Optional child properties: - - label : see Documentation/devicetree/bindings/leds/common.txt + - function : see Documentation/devicetree/bindings/leds/common.txt + - color : see Documentation/devicetree/bindings/leds/common.txt + - label : see Documentation/devicetree/bindings/leds/common.txt (deprecated) - linux,default-trigger : see Documentation/devicetree/bindings/leds/common.txt Example: +#include <dt-bindings/leds/common.h> + led-controller@36 { compatible = "ti,lm3692x"; reg = <0x36>; @@ -43,7 +47,8 @@ led-controller@36 { led@0 { reg = <0>; - label = "white:backlight_cluster"; + function = LED_FUNCTION_BACKLIGHT; + color = <LED_COLOR_ID_WHITE>; linux,default-trigger = "backlight"; }; } diff --git a/Documentation/devicetree/bindings/leds/leds-lm3697.txt b/Documentation/devicetree/bindings/leds/leds-lm3697.txt new file mode 100644 index 000000000000..63992d732959 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-lm3697.txt @@ -0,0 +1,73 @@ +* Texas Instruments - LM3697 Highly Efficient White LED Driver + +The LM3697 11-bit LED driver provides high- +performance backlight dimming for 1, 2, or 3 series +LED strings while delivering up to 90% efficiency. + +This device is suitable for display and keypad lighting + +Required properties: + - compatible: + "ti,lm3697" + - reg : I2C slave address + - #address-cells : 1 + - #size-cells : 0 + +Optional properties: + - enable-gpios : GPIO pin to enable/disable the device + - vled-supply : LED supply + +Required child properties: + - reg : 0 - LED is Controlled by bank A + 1 - LED is Controlled by bank B + - led-sources : Indicates which HVLED string is associated to which + control bank. This is a zero based property so + HVLED1 = 0, HVLED2 = 1, HVLED3 = 2. + Additional information is contained + in Documentation/devicetree/bindings/leds/common.txt + +Optional child properties: + - ti,brightness-resolution - see Documentation/devicetree/bindings/mfd/ti-lmu.txt + - ramp-up-us: see Documentation/devicetree/bindings/mfd/ti-lmu.txt + - ramp-down-us: see Documentation/devicetree/bindings/mfd/ti-lmu.txt + - label : see Documentation/devicetree/bindings/leds/common.txt + - linux,default-trigger : + see Documentation/devicetree/bindings/leds/common.txt + +Example: + +HVLED string 1 and 3 are controlled by control bank A and HVLED 2 string is +controlled by control bank B. + +led-controller@36 { + compatible = "ti,lm3697"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x36>; + + enable-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; + vled-supply = <&vbatt>; + + led@0 { + reg = <0>; + led-sources = <0 2>; + ti,brightness-resolution = <2047>; + ramp-up-us = <5000>; + ramp-down-us = <1000>; + label = "white:first_backlight_cluster"; + linux,default-trigger = "backlight"; + }; + + led@1 { + reg = <1>; + led-sources = <1>; + ti,brightness-resolution = <255>; + ramp-up-us = <500>; + ramp-down-us = <1000>; + label = "white:second_backlight_cluster"; + linux,default-trigger = "backlight"; + }; +} + +For more product information please see the link below: +http://www.ti.com/lit/ds/symlink/lm3697.pdf diff --git a/Documentation/devicetree/bindings/leds/leds-lp8860.txt b/Documentation/devicetree/bindings/leds/leds-lp8860.txt index 5f0e892ad759..9863220db4ba 100644 --- a/Documentation/devicetree/bindings/leds/leds-lp8860.txt +++ b/Documentation/devicetree/bindings/leds/leds-lp8860.txt @@ -20,12 +20,16 @@ Required child properties: - reg : 0 Optional child properties: - - label : see Documentation/devicetree/bindings/leds/common.txt + - function : see Documentation/devicetree/bindings/leds/common.txt + - color : see Documentation/devicetree/bindings/leds/common.txt + - label : see Documentation/devicetree/bindings/leds/common.txt (deprecated) - linux,default-trigger : see Documentation/devicetree/bindings/leds/common.txt Example: +#include <dt-bindings/leds/common.h> + led-controller@2d { compatible = "ti,lp8860"; #address-cells = <1>; @@ -36,7 +40,8 @@ led-controller@2d { led@0 { reg = <0>; - label = "white:backlight"; + function = LED_FUNCTION_BACKLIGHT; + color = <LED_COLOR_ID_WHITE>; linux,default-trigger = "backlight"; }; } diff --git a/Documentation/devicetree/bindings/leds/leds-lt3593.txt b/Documentation/devicetree/bindings/leds/leds-lt3593.txt index 6b2cabc36c0c..24eccdaa6322 100644 --- a/Documentation/devicetree/bindings/leds/leds-lt3593.txt +++ b/Documentation/devicetree/bindings/leds/leds-lt3593.txt @@ -9,8 +9,10 @@ The hardware supports only one LED. The properties of this LED are configured in a sub-node in the device node. Optional sub-node properties: -- label: A label for the LED. If none is given, the LED will be - named "lt3595::". +- function: See Documentation/devicetree/bindings/leds/common.txt +- color: See Documentation/devicetree/bindings/leds/common.txt +- label: A label for the LED. If none is given, the LED will be + named "lt3595::" (deprecated) - linux,default-trigger: The default trigger for the LED. See Documentation/devicetree/bindings/leds/common.txt - default-state: The initial state of the LED. @@ -21,12 +23,15 @@ be handled by its own device node. Example: +#include <dt-bindings/leds/common.h> + led-controller { compatible = "lltc,lt3593"; lltc,ctrl-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; led { - label = "white:backlight"; + function = LED_FUNCTION_BACKLIGHT; + color = <LED_COLOR_ID_WHITE>; default-state = "on"; }; }; diff --git a/Documentation/devicetree/bindings/leds/leds-sc27xx-bltc.txt b/Documentation/devicetree/bindings/leds/leds-sc27xx-bltc.txt index dddf84f9c7ea..df2b4e1c492b 100644 --- a/Documentation/devicetree/bindings/leds/leds-sc27xx-bltc.txt +++ b/Documentation/devicetree/bindings/leds/leds-sc27xx-bltc.txt @@ -14,7 +14,9 @@ Required child properties: - reg: Port this LED is connected to. Optional child properties: -- label: See Documentation/devicetree/bindings/leds/common.txt. +- function: See Documentation/devicetree/bindings/leds/common.txt. +- color: See Documentation/devicetree/bindings/leds/common.txt. +- label: See Documentation/devicetree/bindings/leds/common.txt (deprecated). Examples: @@ -25,17 +27,17 @@ led-controller@200 { reg = <0x200>; led@0 { - label = "red"; + color = <LED_COLOR_ID_RED>; reg = <0x0>; }; led@1 { - label = "green"; + color = <LED_COLOR_ID_GREEN>; reg = <0x1>; }; led@2 { - label = "blue"; + color = <LED_COLOR_ID_BLUE>; reg = <0x2>; }; }; diff --git a/Documentation/devicetree/bindings/leds/leds-spi-byte.txt b/Documentation/devicetree/bindings/leds/leds-spi-byte.txt new file mode 100644 index 000000000000..28b6b2d9091e --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-spi-byte.txt @@ -0,0 +1,44 @@ +* Single Byte SPI LED Device Driver. + +The driver can be used for controllers with a very simple SPI protocol: +- one LED is controlled by a single byte on MOSI +- the value of the byte gives the brightness between two values (lowest to + highest) +- no return value is necessary (no MISO signal) + +The value for lowest and highest brightness is dependent on the device and +therefore on the compatible string. + +Depending on the compatible string some special functions (like hardware +accelerated blinking) might can be supported too. + +The driver currently only supports one LED. The properties of the LED are +configured in a sub-node in the device node. + +Required properties: +- compatible: should be one of + * "ubnt,acb-spi-led" microcontroller (SONiX 8F26E611LA) based device + used for example in Ubiquiti airCube ISP + +Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt +apply. + +LED sub-node properties: +- label: + see Documentation/devicetree/bindings/leds/common.txt +- default-state: + see Documentation/devicetree/bindings/leds/common.txt + Only "on" and "off" are supported. + +Example: + +led-controller@0 { + compatible = "ubnt,acb-spi-led"; + reg = <0>; + spi-max-frequency = <100000>; + + led { + label = "white:status"; + default-state = "on"; + }; +}; diff --git a/Documentation/devicetree/bindings/mailbox/amlogic,meson-gxbb-mhu.yaml b/Documentation/devicetree/bindings/mailbox/amlogic,meson-gxbb-mhu.yaml new file mode 100644 index 000000000000..319280563648 --- /dev/null +++ b/Documentation/devicetree/bindings/mailbox/amlogic,meson-gxbb-mhu.yaml @@ -0,0 +1,52 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 BayLibre, SAS +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/mailbox/amlogic,meson-gxbb-mhu.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Amlogic Meson Message-Handling-Unit Controller + +maintainers: + - Neil Armstrong <narmstrong@baylibre.com> + +description: | + The Amlogic's Meson SoCs Message-Handling-Unit (MHU) is a mailbox controller + that has 3 independent channels/links to communicate with remote processor(s). + MHU links are hardwired on a platform. A link raises interrupt for any + received data. However, there is no specified way of knowing if the sent + data has been read by the remote. This driver assumes the sender polls + STAT register and the remote clears it after having read the data. + +properties: + compatible: + enum: + - amlogic,meson-gxbb-mhu + + reg: + maxItems: 1 + + interrupts: + minItems: 3 + description: + Contains the interrupt information corresponding to each of the 3 links + of MHU. + + "#mbox-cells": + const: 1 + +required: + - compatible + - reg + - interrupts + - "#mbox-cells" + +examples: + - | + mailbox@c883c404 { + compatible = "amlogic,meson-gxbb-mhu"; + reg = <0xc883c404 0x4c>; + interrupts = <208>, <209>, <210>; + #mbox-cells = <1>; + }; + diff --git a/Documentation/devicetree/bindings/mailbox/meson-mhu.txt b/Documentation/devicetree/bindings/mailbox/meson-mhu.txt deleted file mode 100644 index a530310772b9..000000000000 --- a/Documentation/devicetree/bindings/mailbox/meson-mhu.txt +++ /dev/null @@ -1,34 +0,0 @@ -Amlogic Meson MHU Mailbox Driver -================================ - -The Amlogic's Meson SoCs Message-Handling-Unit (MHU) is a mailbox controller -that has 3 independent channels/links to communicate with remote processor(s). -MHU links are hardwired on a platform. A link raises interrupt for any -received data. However, there is no specified way of knowing if the sent -data has been read by the remote. This driver assumes the sender polls -STAT register and the remote clears it after having read the data. - -Mailbox Device Node: -==================== - -Required properties: --------------------- -- compatible: Shall be "amlogic,meson-gxbb-mhu" -- reg: Contains the mailbox register address range (base - address and length) -- #mbox-cells Shall be 1 - the index of the channel needed. -- interrupts: Contains the interrupt information corresponding to - each of the 2 links of MHU. - -Example: --------- - - mailbox: mailbox@c883c404 { - #mbox-cells = <1>; - compatible = "amlogic,meson-gxbb-mhu"; - reg = <0 0xc883c404 0 0x4c>; - interrupts = <0 208 IRQ_TYPE_EDGE_RISING>, - <0 209 IRQ_TYPE_EDGE_RISING>, - <0 210 IRQ_TYPE_EDGE_RISING>; - #mbox-cells = <1>; - }; diff --git a/Documentation/devicetree/bindings/mailbox/mtk-gce.txt b/Documentation/devicetree/bindings/mailbox/mtk-gce.txt index 7d72b21c9e94..7b13787ab13d 100644 --- a/Documentation/devicetree/bindings/mailbox/mtk-gce.txt +++ b/Documentation/devicetree/bindings/mailbox/mtk-gce.txt @@ -9,7 +9,7 @@ CMDQ driver uses mailbox framework for communication. Please refer to mailbox.txt for generic information about mailbox device-tree bindings. Required properties: -- compatible: Must be "mediatek,mt8173-gce" +- compatible: can be "mediatek,mt8173-gce" or "mediatek,mt8183-gce" - reg: Address range of the GCE unit - interrupts: The interrupt signal from the GCE block - clock: Clocks according to the common clock binding @@ -25,11 +25,19 @@ Required properties: Required properties for a client device: - mboxes: Client use mailbox to communicate with GCE, it should have this property and list of phandle, mailbox specifiers. -- mediatek,gce-subsys: u32, specify the sub-system id which is corresponding - to the register address. +Optional properties for a client device: +- mediatek,gce-client-reg: Specify the sub-system id which is corresponding + to the register address, it should have this property and list of phandle, + sub-system specifiers. + <&phandle subsys_number start_offset size> + phandle: Label name of a gce node. + subsys_number: specify the sub-system id which is corresponding + to the register address. + start_offset: the start offset of register address that GCE can access. + size: the total size of register address that GCE can access. -Some vaules of properties are defined in 'dt-bindings/gce/mt8173-gce.h'. Such as -sub-system ids, thread priority, event ids. +Some vaules of properties are defined in 'dt-bindings/gce/mt8173-gce.h' +or 'dt-binding/gce/mt8183-gce.h'. Such as sub-system ids, thread priority, event ids. Example: @@ -39,7 +47,6 @@ Example: interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_LOW>; clocks = <&infracfg CLK_INFRA_GCE>; clock-names = "gce"; - thread-num = CMDQ_THR_MAX_COUNT; #mbox-cells = <3>; }; @@ -49,9 +56,9 @@ Example for a client device: compatible = "mediatek,mt8173-mmsys"; mboxes = <&gce 0 CMDQ_THR_PRIO_LOWEST 1>, <&gce 1 CMDQ_THR_PRIO_LOWEST 1>; - mediatek,gce-subsys = <SUBSYS_1400XXXX>; mutex-event-eof = <CMDQ_EVENT_MUTEX0_STREAM_EOF CMDQ_EVENT_MUTEX1_STREAM_EOF>; - + mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0x3000 0x1000>, + <&gce SUBSYS_1401XXXX 0x2000 0x100>; ... }; diff --git a/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt index 0ef372656a3e..35c3f56b7f7b 100644 --- a/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt +++ b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt @@ -1,4 +1,4 @@ -OMAP2+ Mailbox Driver +OMAP2+ and K3 Mailbox ===================== The OMAP mailbox hardware facilitates communication between different processors @@ -7,7 +7,7 @@ various processor subsystems and is connected on an interconnect bus. The communication is achieved through a set of registers for message storage and interrupt configuration registers. -Each mailbox IP block has a certain number of h/w fifo queues and output +Each mailbox IP block/cluster has a certain number of h/w fifo queues and output interrupt lines. An output interrupt line is routed to an interrupt controller within a processor subsystem, and there can be more than one line going to a specific processor's interrupt controller. The interrupt line connections are @@ -23,12 +23,16 @@ All the current OMAP SoCs except for the newest DRA7xx SoC has a single IP instance. DRA7xx has multiple instances with different number of h/w fifo queues and interrupt lines between different instances. The interrupt lines can also be routed to different processor sub-systems on DRA7xx as they are routed through -the Crossbar, a kind of interrupt router/multiplexer. +the Crossbar, a kind of interrupt router/multiplexer. The K3 AM65x and J721E +SoCs has each of these instances form a cluster and combine multiple clusters +into a single IP block present within the Main NavSS. The interrupt lines from +all these clusters are multiplexed and routed to different processor subsystems +over a limited number of common interrupt output lines of an Interrupt Router. Mailbox Device Node: ==================== -A Mailbox device node is used to represent a Mailbox IP instance within a SoC. -The sub-mailboxes are represented as child nodes of this parent node. +A Mailbox device node is used to represent a Mailbox IP instance/cluster within +a SoC. The sub-mailboxes are represented as child nodes of this parent node. Required properties: -------------------- @@ -37,12 +41,12 @@ Required properties: "ti,omap3-mailbox" for OMAP3430, OMAP3630 SoCs "ti,omap4-mailbox" for OMAP44xx, OMAP54xx, AM33xx, AM43xx and DRA7xx SoCs + "ti,am654-mailbox" for K3 AM65x and J721E SoCs - reg: Contains the mailbox register address range (base address and length) - interrupts: Contains the interrupt information for the mailbox device. The format is dependent on which interrupt - controller the OMAP device uses -- ti,hwmods: Name of the hwmod associated with the mailbox + controller the Mailbox device uses - #mbox-cells: Common mailbox binding property to identify the number of cells required for the mailbox specifier. Should be 1 @@ -50,6 +54,23 @@ Required properties: device can interrupt - ti,mbox-num-fifos: Number of h/w fifo queues within the mailbox IP block +SoC-specific Required properties: +--------------------------------- +The following are mandatory properties for the OMAP architecture based SoCs +only: +- ti,hwmods: Name of the hwmod associated with the mailbox. This + should be defined in the mailbox node only if the node + is not defined as a child node of a corresponding sysc + interconnect node. + +The following are mandatory properties for the K3 AM65x and J721E SoCs only: +- interrupt-parent: Should contain a phandle to the TI-SCI interrupt + controller node that is used to dynamically program + the interrupt routes between the IP and the main GIC + controllers. See the following binding for additional + details, + Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt + Child Nodes: ============ A child node is used for representing the actual sub-mailbox device that is @@ -98,7 +119,7 @@ to be used by the client user. Example: -------- -/* OMAP4 */ +1. /* OMAP4 */ mailbox: mailbox@4a0f4000 { compatible = "ti,omap4-mailbox"; reg = <0x4a0f4000 0x200>; @@ -123,7 +144,7 @@ dsp { ... }; -/* AM33xx */ +2. /* AM33xx */ mailbox: mailbox@480c8000 { compatible = "ti,omap4-mailbox"; reg = <0x480C8000 0x200>; @@ -137,3 +158,23 @@ mailbox: mailbox@480c8000 { ti,mbox-rx = <0 0 3>; }; }; + +3. /* AM65x */ +&cbass_main { + cbass_main_navss: interconnect0 { + mailbox0_cluster0: mailbox@31f80000 { + compatible = "ti,am654-mailbox"; + reg = <0x00 0x31f80000 0x00 0x200>; + #mbox-cells = <1>; + ti,mbox-num-users = <4>; + ti,mbox-num-fifos = <16>; + interrupt-parent = <&intr_main_navss>; + interrupts = <164 0>; + + mbox_mcu_r5fss0_core0: mbox-mcu-r5fss0-core0 { + ti,mbox-tx = <1 0 0>; + ti,mbox-rx = <0 0 0>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.txt b/Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.txt index 1232fc9fc709..0278482af65c 100644 --- a/Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.txt +++ b/Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.txt @@ -12,7 +12,10 @@ platforms. "qcom,msm8996-apcs-hmss-global" "qcom,msm8998-apcs-hmss-global" "qcom,qcs404-apcs-apps-global" + "qcom,sc7180-apss-shared" "qcom,sdm845-apss-shared" + "qcom,sm8150-apss-shared" + "qcom,ipq8074-apcs-apps-global" - reg: Usage: required diff --git a/Documentation/devicetree/bindings/media/allegro.txt b/Documentation/devicetree/bindings/media/allegro.txt new file mode 100644 index 000000000000..a92e2fbf26c9 --- /dev/null +++ b/Documentation/devicetree/bindings/media/allegro.txt @@ -0,0 +1,43 @@ +Device-tree bindings for the Allegro DVT video IP codecs present in the Xilinx +ZynqMP SoC. The IP core may either be a H.264/H.265 encoder or H.264/H.265 +decoder ip core. + +Each actual codec engines is controlled by a microcontroller (MCU). Host +software uses a provided mailbox interface to communicate with the MCU. The +MCU share an interrupt. + +Required properties: + - compatible: value should be one of the following + "allegro,al5e-1.1", "allegro,al5e": encoder IP core + "allegro,al5d-1.1", "allegro,al5d": decoder IP core + - reg: base and length of the memory mapped register region and base and + length of the memory mapped sram + - reg-names: must include "regs" and "sram" + - interrupts: shared interrupt from the MCUs to the processing system + - clocks: must contain an entry for each entry in clock-names + - clock-names: must include "core_clk", "mcu_clk", "m_axi_core_aclk", + "m_axi_mcu_aclk", "s_axi_lite_aclk" + +Example: + al5e: video-codec@a0009000 { + compatible = "allegro,al5e-1.1", "allegro,al5e"; + reg = <0 0xa0009000 0 0x1000>, + <0 0xa0000000 0 0x8000>; + reg-names = "regs", "sram"; + interrupts = <0 96 4>; + clocks = <&xlnx_vcu 0>, <&xlnx_vcu 1>, + <&clkc 71>, <&clkc 71>, <&clkc 71>; + clock-names = "core_clk", "mcu_clk", "m_axi_core_aclk", + "m_axi_mcu_aclk", "s_axi_lite_aclk" + }; + al5d: video-codec@a0029000 { + compatible = "allegro,al5d-1.1", "allegro,al5d"; + reg = <0 0xa0029000 0 0x1000>, + <0 0xa0020000 0 0x8000>; + reg-names = "regs", "sram"; + interrupts = <0 96 4>; + clocks = <&xlnx_vcu 2>, <&xlnx_vcu 3>, + <&clkc 71>, <&clkc 71>, <&clkc 71>; + clock-names = "core_clk", "mcu_clk", "m_axi_core_aclk", + "m_axi_mcu_aclk", "s_axi_lite_aclk" + }; diff --git a/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-csi.yaml b/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-csi.yaml new file mode 100644 index 000000000000..27f38eed389e --- /dev/null +++ b/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-csi.yaml @@ -0,0 +1,109 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/allwinner,sun4i-a10-csi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 CMOS Sensor Interface (CSI) Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +description: |- + The Allwinner A10 and later has a CMOS Sensor Interface to retrieve + frames from a parallel or BT656 sensor. + +properties: + compatible: + const: allwinner,sun7i-a20-csi0 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: The CSI interface clock + - description: The CSI module clock + - description: The CSI ISP clock + - description: The CSI DRAM clock + + clock-names: + items: + - const: bus + - const: mod + - const: isp + - const: ram + + resets: + maxItems: 1 + + # See ./video-interfaces.txt for details + port: + type: object + additionalProperties: false + + properties: + endpoint: + type: object + + properties: + bus-width: + enum: [8, 16] + + data-active: true + hsync-active: true + pclk-sample: true + remote-endpoint: true + vsync-active: true + + required: + - bus-width + - data-active + - hsync-active + - pclk-sample + - remote-endpoint + - vsync-active + + required: + - endpoint + +required: + - compatible + - reg + - interrupts + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/sun7i-a20-ccu.h> + #include <dt-bindings/reset/sun4i-a10-ccu.h> + + csi0: csi@1c09000 { + compatible = "allwinner,sun7i-a20-csi0"; + reg = <0x01c09000 0x1000>; + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_AHB_CSI0>, <&ccu CLK_CSI0>, + <&ccu CLK_CSI_SCLK>, <&ccu CLK_DRAM_CSI0>; + clock-names = "bus", "mod", "isp", "ram"; + resets = <&ccu RST_CSI0>; + + port { + csi_from_ov5640: endpoint { + remote-endpoint = <&ov5640_to_csi>; + bus-width = <8>; + hsync-active = <1>; /* Active high */ + vsync-active = <0>; /* Active low */ + data-active = <1>; /* Active high */ + pclk-sample = <1>; /* Rising */ + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-ir.yaml b/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-ir.yaml new file mode 100644 index 000000000000..98c1bdde9a86 --- /dev/null +++ b/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-ir.yaml @@ -0,0 +1,80 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/allwinner,sun4i-a10-ir.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 Infrared Controller Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +allOf: + - $ref: "rc.yaml#" + +properties: + compatible: + oneOf: + - const: allwinner,sun4i-a10-ir + - const: allwinner,sun5i-a13-ir + - items: + - const: allwinner,sun8i-a83t-ir + - const: allwinner,sun6i-a31-ir + - const: allwinner,sun6i-a31-ir + - items: + - const: allwinner,sun50i-a64-ir + - const: allwinner,sun6i-a31-ir + - items: + - const: allwinner,sun50i-h6-ir + - const: allwinner,sun6i-a31-ir + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Bus Clock + - description: Module Clock + + clock-names: + items: + - const: apb + - const: ir + + resets: + maxItems: 1 + + clock-frequency: + default: 8000000 + description: + IR Receiver clock frequency, in Hertz. + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +# FIXME: We should set it, but it would report all the generic +# properties as additional properties. +# additionalProperties: false + +examples: + - | + ir0: ir@1c21800 { + compatible = "allwinner,sun4i-a10-ir"; + clocks = <&apb0_gates 6>, <&ir0_clk>; + clock-names = "apb", "ir"; + clock-frequency = <3000000>; + resets = <&apb0_rst 1>; + interrupts = <0 5 1>; + reg = <0x01C21800 0x40>; + linux,rc-map-name = "rc-rc6-mce"; + }; + +... diff --git a/Documentation/devicetree/bindings/media/amlogic,vdec.txt b/Documentation/devicetree/bindings/media/amlogic,vdec.txt new file mode 100644 index 000000000000..9b6aace86ca7 --- /dev/null +++ b/Documentation/devicetree/bindings/media/amlogic,vdec.txt @@ -0,0 +1,72 @@ +Amlogic Video Decoder +================================ + +The video decoding IP lies within the DOS memory region, +except for the hardware bitstream parser that makes use of an undocumented +region. + +It makes use of the following blocks: + +- ESPARSER is a bitstream parser that outputs to a VIFIFO. Further VDEC blocks +then feed from this VIFIFO. +- VDEC_1 can decode MPEG-1, MPEG-2, MPEG-4 part 2, MJPEG, H.263, H.264, VC-1. +- VDEC_HEVC can decode HEVC and VP9. + +Both VDEC_1 and VDEC_HEVC share the "vdec" IRQ and as such cannot run +concurrently. + +Device Tree Bindings: +--------------------- + +VDEC: Video Decoder +-------------------------- + +Required properties: +- compatible: value should be different for each SoC family as : + - GXBB (S905) : "amlogic,gxbb-vdec" + - GXL (S905X, S905D) : "amlogic,gxl-vdec" + - GXM (S912) : "amlogic,gxm-vdec" + followed by the common "amlogic,gx-vdec" +- reg: base address and size of he following memory-mapped regions : + - dos + - esparser +- reg-names: should contain the names of the previous memory regions +- interrupts: should contain the following IRQs: + - vdec + - esparser +- interrupt-names: should contain the names of the previous interrupts +- amlogic,ao-sysctrl: should point to the AOBUS sysctrl node +- amlogic,canvas: should point to a canvas provider node +- clocks: should contain the following clocks : + - dos_parser + - dos + - vdec_1 + - vdec_hevc +- clock-names: should contain the names of the previous clocks +- resets: should contain the parser reset +- reset-names: should be "esparser" + +Example: + +vdec: video-codec@c8820000 { + compatible = "amlogic,gxbb-vdec", "amlogic,gx-vdec"; + reg = <0x0 0xc8820000 0x0 0x10000>, + <0x0 0xc110a580 0x0 0xe4>; + reg-names = "dos", "esparser"; + + interrupts = <GIC_SPI 44 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 32 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "vdec", "esparser"; + + amlogic,ao-sysctrl = <&sysctrl_AO>; + amlogic,canvas = <&canvas>; + + clocks = <&clkc CLKID_DOS_PARSER>, + <&clkc CLKID_DOS>, + <&clkc CLKID_VDEC_1>, + <&clkc CLKID_VDEC_HEVC>; + clock-names = "dos_parser", "dos", "vdec_1", "vdec_hevc"; + + resets = <&reset RESET_PARSER>; + reset-names = "esparser"; +}; diff --git a/Documentation/devicetree/bindings/media/cdns,csi2tx.txt b/Documentation/devicetree/bindings/media/cdns,csi2tx.txt index 459c6e332f52..751b9edf1247 100644 --- a/Documentation/devicetree/bindings/media/cdns,csi2tx.txt +++ b/Documentation/devicetree/bindings/media/cdns,csi2tx.txt @@ -5,7 +5,8 @@ The Cadence MIPI-CSI2 TX controller is a CSI-2 bridge supporting up to 4 CSI lanes in output, and up to 4 different pixel streams in input. Required properties: - - compatible: must be set to "cdns,csi2tx" + - compatible: must be set to "cdns,csi2tx" or "cdns,csi2tx-1.3" + for version 1.3 of the controller, "cdns,csi2tx-2.1" for v2.1 - reg: base address and size of the memory mapped region - clocks: phandles to the clocks driving the controller - clock-names: must contain: diff --git a/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt index 8ee7c7972ac7..c3c3479233c4 100644 --- a/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt +++ b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt @@ -7,6 +7,9 @@ of that. These definitions are valid for both types of sensors. More detailed documentation can be found in Documentation/devicetree/bindings/media/video-interfaces.txt . +The device node should contain a "port" node which may contain one or more +endpoint nodes, in accordance with video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt . Mandatory properties -------------------- @@ -37,9 +40,7 @@ Optional properties Endpoint node mandatory properties ---------------------------------- -- clock-lanes: <0> - data-lanes: <1..n> -- remote-endpoint: A phandle to the bus receiver's endpoint node. Example @@ -48,7 +49,7 @@ Example &i2c2 { clock-frequency = <400000>; - smiapp_1: camera@10 { + camera-sensor@10 { compatible = "nokia,smia"; reg = <0x10>; reset-gpios = <&gpio3 20 0>; @@ -58,8 +59,7 @@ Example nokia,nvm-size = <512>; /* 8 * 64 */ link-frequencies = /bits/ 64 <199200000 210000000 499200000>; port { - smiapp_1_1: endpoint { - clock-lanes = <0>; + smiapp_ep: endpoint { data-lanes = <1 2>; remote-endpoint = <&csi2a_ep>; }; diff --git a/Documentation/devicetree/bindings/media/imx7-csi.txt b/Documentation/devicetree/bindings/media/imx7-csi.txt index 3c07bc676bc3..d80ceefa0c00 100644 --- a/Documentation/devicetree/bindings/media/imx7-csi.txt +++ b/Documentation/devicetree/bindings/media/imx7-csi.txt @@ -9,13 +9,12 @@ to connect directly to external CMOS image sensors. Required properties: -- compatible : "fsl,imx7-csi"; +- compatible : "fsl,imx7-csi" or "fsl,imx6ul-csi"; - reg : base address and length of the register set for the device; - interrupts : should contain CSI interrupt; - clocks : list of clock specifiers, see Documentation/devicetree/bindings/clock/clock-bindings.txt for details; -- clock-names : must contain "axi", "mclk" and "dcic" entries, matching - entries in the clock property; +- clock-names : must contain "mclk"; The device node shall contain one 'port' child node with one child 'endpoint' node, according to the bindings defined in: @@ -32,10 +31,8 @@ example: compatible = "fsl,imx7-csi"; reg = <0x30710000 0x10000>; interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clks IMX7D_CLK_DUMMY>, - <&clks IMX7D_CSI_MCLK_ROOT_CLK>, - <&clks IMX7D_CLK_DUMMY>; - clock-names = "axi", "mclk", "dcic"; + clocks = <&clks IMX7D_CSI_MCLK_ROOT_CLK>; + clock-names = "mclk"; port { csi_from_csi_mux: endpoint { diff --git a/Documentation/devicetree/bindings/media/marvell,mmp2-ccic.txt b/Documentation/devicetree/bindings/media/marvell,mmp2-ccic.txt new file mode 100644 index 000000000000..7ec2c8c8a3b9 --- /dev/null +++ b/Documentation/devicetree/bindings/media/marvell,mmp2-ccic.txt @@ -0,0 +1,50 @@ +Marvell MMP2 camera host interface + +Required properties: + - compatible: Should be "marvell,mmp2-ccic". + - reg: Register base and size. + - interrupts: The interrupt number. + - #clock-cells: Must be 0. + +Optional properties: + - clocks: Reference to the input clock as specified by + Documentation/devicetree/bindings/clock/clock-bindings.txt. + - clock-names: Names of the clocks used; "axi" for the AXI bus interface, + "func" for the peripheral clock and "phy" for the parallel + video bus interface. + - clock-output-names: Optional clock source for sensors. Shall be "mclk". + +Required subnodes: + - port: The parallel bus interface port with a single endpoint linked to + the sensor's endpoint as described in + Documentation/devicetree/bindings/media/video-interfaces.txt. + +Required endpoint properties: + - bus-type: data bus type, <5> or <6> for Parallel or Bt.656 respectively + - pclk-sample: pixel clock polarity + - hsync-active: horizontal synchronization polarity (only required for + parallel bus) + - vsync-active: vertical synchronization polarity (only required for + parallel bus) + +Example: + + camera0: camera@d420a000 { + compatible = "marvell,mmp2-ccic"; + reg = <0xd420a000 0x800>; + interrupts = <42>; + clocks = <&soc_clocks MMP2_CLK_CCIC0>; + clock-names = "axi"; + #clock-cells = <0>; + clock-output-names = "mclk"; + + port { + camera0_0: endpoint { + remote-endpoint = <&ov7670_0>; + bus-type = <5>; /* Parallel */ + hsync-active = <1>; /* Active high */ + vsync-active = <1>; /* Active high */ + pclk-sample = <0>; /* Falling */ + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/meson-ao-cec.txt b/Documentation/devicetree/bindings/media/meson-ao-cec.txt index c67fc41d4aa2..ad92ee41c0dd 100644 --- a/Documentation/devicetree/bindings/media/meson-ao-cec.txt +++ b/Documentation/devicetree/bindings/media/meson-ao-cec.txt @@ -5,10 +5,12 @@ to handle communication between HDMI connected devices over the CEC bus. Required properties: - compatible : value should be following depending on the SoC : - For GXBB, GXL, GXM and G12A (AO_CEC_A module) : + For GXBB, GXL, GXM, G12A and SM1 (AO_CEC_A module) : "amlogic,meson-gx-ao-cec" For G12A (AO_CEC_B module) : "amlogic,meson-g12a-ao-cec" + For SM1 (AO_CEC_B module) : + "amlogic,meson-sm1-ao-cec" - reg : Physical base address of the IP registers and length of memory mapped region. @@ -16,9 +18,9 @@ Required properties: - interrupts : AO-CEC interrupt number to the CPU. - clocks : from common clock binding: handle to AO-CEC clock. - clock-names : from common clock binding, must contain : - For GXBB, GXL, GXM and G12A (AO_CEC_A module) : + For GXBB, GXL, GXM, G12A and SM1 (AO_CEC_A module) : - "core" - For G12A (AO_CEC_B module) : + For G12A, SM1 (AO_CEC_B module) : - "oscin" corresponding to entry in the clocks property. - hdmi-phandle: phandle to the HDMI controller diff --git a/Documentation/devicetree/bindings/media/nvidia,tegra-vde.txt b/Documentation/devicetree/bindings/media/nvidia,tegra-vde.txt index 7302e949e662..602169b8aa19 100644 --- a/Documentation/devicetree/bindings/media/nvidia,tegra-vde.txt +++ b/Documentation/devicetree/bindings/media/nvidia,tegra-vde.txt @@ -35,6 +35,7 @@ Optional properties: - resets : Must contain an entry for each entry in reset-names. - reset-names : Must include the following entries: - mc +- iommus: Must contain phandle to the IOMMU device node. Example: @@ -59,4 +60,5 @@ video-codec@6001a000 { clocks = <&tegra_car TEGRA20_CLK_VDE>; reset-names = "vde", "mc"; resets = <&tegra_car 61>, <&mc TEGRA20_MC_RESET_VDE>; + iommus = <&mc TEGRA_SWGROUP_VDE>; }; diff --git a/Documentation/devicetree/bindings/media/rc.txt b/Documentation/devicetree/bindings/media/rc.txt index d3e7a012bfda..be629f7fa77e 100644 --- a/Documentation/devicetree/bindings/media/rc.txt +++ b/Documentation/devicetree/bindings/media/rc.txt @@ -1,117 +1 @@ -The following properties are common to the infrared remote controllers: - -- linux,rc-map-name: string, specifies the scancode/key mapping table - defined in-kernel for the remote controller. Support values are: - * "rc-adstech-dvb-t-pci" - * "rc-alink-dtu-m" - * "rc-anysee" - * "rc-apac-viewcomp" - * "rc-asus-pc39" - * "rc-asus-ps3-100" - * "rc-ati-tv-wonder-hd-600" - * "rc-ati-x10" - * "rc-avermedia-a16d" - * "rc-avermedia-cardbus" - * "rc-avermedia-dvbt" - * "rc-avermedia-m135a" - * "rc-avermedia-m733a-rm-k6" - * "rc-avermedia-rm-ks" - * "rc-avermedia" - * "rc-avertv-303" - * "rc-azurewave-ad-tu700" - * "rc-behold-columbus" - * "rc-behold" - * "rc-budget-ci-old" - * "rc-cec" - * "rc-cinergy-1400" - * "rc-cinergy" - * "rc-delock-61959" - * "rc-dib0700-nec" - * "rc-dib0700-rc5" - * "rc-digitalnow-tinytwin" - * "rc-digittrade" - * "rc-dm1105-nec" - * "rc-dntv-live-dvbt-pro" - * "rc-dntv-live-dvb-t" - * "rc-dtt200u" - * "rc-dvbsky" - * "rc-empty" - * "rc-em-terratec" - * "rc-encore-enltv2" - * "rc-encore-enltv-fm53" - * "rc-encore-enltv" - * "rc-evga-indtube" - * "rc-eztv" - * "rc-flydvb" - * "rc-flyvideo" - * "rc-fusionhdtv-mce" - * "rc-gadmei-rm008z" - * "rc-geekbox" - * "rc-genius-tvgo-a11mce" - * "rc-gotview7135" - * "rc-hauppauge" - * "rc-imon-mce" - * "rc-imon-pad" - * "rc-iodata-bctv7e" - * "rc-it913x-v1" - * "rc-it913x-v2" - * "rc-kaiomy" - * "rc-kworld-315u" - * "rc-kworld-pc150u" - * "rc-kworld-plus-tv-analog" - * "rc-leadtek-y04g0051" - * "rc-lirc" - * "rc-lme2510" - * "rc-manli" - * "rc-medion-x10" - * "rc-medion-x10-digitainer" - * "rc-medion-x10-or2x" - * "rc-msi-digivox-ii" - * "rc-msi-digivox-iii" - * "rc-msi-tvanywhere-plus" - * "rc-msi-tvanywhere" - * "rc-nebula" - * "rc-nec-terratec-cinergy-xs" - * "rc-norwood" - * "rc-npgtech" - * "rc-pctv-sedna" - * "rc-pinnacle-color" - * "rc-pinnacle-grey" - * "rc-pinnacle-pctv-hd" - * "rc-pixelview-new" - * "rc-pixelview" - * "rc-pixelview-002t" - * "rc-pixelview-mk12" - * "rc-powercolor-real-angel" - * "rc-proteus-2309" - * "rc-purpletv" - * "rc-pv951" - * "rc-hauppauge" - * "rc-rc5-tv" - * "rc-rc6-mce" - * "rc-real-audio-220-32-keys" - * "rc-reddo" - * "rc-snapstream-firefly" - * "rc-streamzap" - * "rc-tbs-nec" - * "rc-technisat-ts35" - * "rc-technisat-usb2" - * "rc-terratec-cinergy-c-pci" - * "rc-terratec-cinergy-s2-hd" - * "rc-terratec-cinergy-xs" - * "rc-terratec-slim" - * "rc-terratec-slim-2" - * "rc-tevii-nec" - * "rc-tivo" - * "rc-total-media-in-hand" - * "rc-total-media-in-hand-02" - * "rc-trekstor" - * "rc-tt-1500" - * "rc-twinhan-dtv-cab-ci" - * "rc-twinhan1027" - * "rc-videomate-k100" - * "rc-videomate-s350" - * "rc-videomate-tv-pvr" - * "rc-winfast" - * "rc-winfast-usbii-deluxe" - * "rc-su3000" +This file has been moved to rc.yaml. diff --git a/Documentation/devicetree/bindings/media/rc.yaml b/Documentation/devicetree/bindings/media/rc.yaml new file mode 100644 index 000000000000..3d5c154fd230 --- /dev/null +++ b/Documentation/devicetree/bindings/media/rc.yaml @@ -0,0 +1,145 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/rc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Generic Infrared Remote Controller Device Tree Bindings + +maintainers: + - Mauro Carvalho Chehab <mchehab@kernel.org> + - Sean Young <sean@mess.org> + +properties: + $nodename: + pattern: "^ir(@[a-f0-9]+)?$" + + linux,rc-map-name: + description: + Specifies the scancode/key mapping table defined in-kernel for + the remote controller. + allOf: + - $ref: '/schemas/types.yaml#/definitions/string' + - enum: + - rc-adstech-dvb-t-pci + - rc-alink-dtu-m + - rc-anysee + - rc-apac-viewcomp + - rc-astrometa-t2hybrid + - rc-asus-pc39 + - rc-asus-ps3-100 + - rc-ati-tv-wonder-hd-600 + - rc-ati-x10 + - rc-avermedia + - rc-avermedia-a16d + - rc-avermedia-cardbus + - rc-avermedia-dvbt + - rc-avermedia-m135a + - rc-avermedia-m733a-rm-k6 + - rc-avermedia-rm-ks + - rc-avertv-303 + - rc-azurewave-ad-tu700 + - rc-behold + - rc-behold-columbus + - rc-budget-ci-old + - rc-cec + - rc-cinergy + - rc-cinergy-1400 + - rc-d680-dmb + - rc-delock-61959 + - rc-dib0700-nec + - rc-dib0700-rc5 + - rc-digitalnow-tinytwin + - rc-digittrade + - rc-dm1105-nec + - rc-dntv-live-dvb-t + - rc-dntv-live-dvbt-pro + - rc-dtt200u + - rc-dvbsky + - rc-dvico-mce + - rc-dvico-portable + - rc-em-terratec + - rc-empty + - rc-encore-enltv + - rc-encore-enltv-fm53 + - rc-encore-enltv2 + - rc-evga-indtube + - rc-eztv + - rc-flydvb + - rc-flyvideo + - rc-fusionhdtv-mce + - rc-gadmei-rm008z + - rc-geekbox + - rc-genius-tvgo-a11mce + - rc-gotview7135 + - rc-hauppauge + - rc-hauppauge + - rc-hisi-poplar + - rc-hisi-tv-demo + - rc-imon-mce + - rc-imon-pad + - rc-imon-rsc + - rc-iodata-bctv7e + - rc-it913x-v1 + - rc-it913x-v2 + - rc-kaiomy + - rc-kworld-315u + - rc-kworld-pc150u + - rc-kworld-plus-tv-analog + - rc-leadtek-y04g0051 + - rc-lme2510 + - rc-manli + - rc-medion-x10 + - rc-medion-x10-digitainer + - rc-medion-x10-or2x + - rc-msi-digivox-ii + - rc-msi-digivox-iii + - rc-msi-tvanywhere + - rc-msi-tvanywhere-plus + - rc-nebula + - rc-nec-terratec-cinergy-xs + - rc-norwood + - rc-npgtech + - rc-pctv-sedna + - rc-pinnacle-color + - rc-pinnacle-grey + - rc-pinnacle-pctv-hd + - rc-pixelview + - rc-pixelview-002t + - rc-pixelview-mk12 + - rc-pixelview-new + - rc-powercolor-real-angel + - rc-proteus-2309 + - rc-purpletv + - rc-pv951 + - rc-rc5-tv + - rc-rc6-mce + - rc-real-audio-220-32-keys + - rc-reddo + - rc-snapstream-firefly + - rc-streamzap + - rc-su3000 + - rc-tango + - rc-tbs-nec + - rc-technisat-ts35 + - rc-technisat-usb2 + - rc-terratec-cinergy-c-pci + - rc-terratec-cinergy-s2-hd + - rc-terratec-cinergy-xs + - rc-terratec-slim + - rc-terratec-slim-2 + - rc-tevii-nec + - rc-tivo + - rc-total-media-in-hand + - rc-total-media-in-hand-02 + - rc-trekstor + - rc-tt-1500 + - rc-twinhan-dtv-cab-ci + - rc-twinhan1027 + - rc-videomate-k100 + - rc-videomate-s350 + - rc-videomate-tv-pvr + - rc-winfast + - rc-winfast-usbii-deluxe + - rc-xbox-dvd + - rc-zx-irdec diff --git a/Documentation/devicetree/bindings/media/renesas,rcar-csi2.txt b/Documentation/devicetree/bindings/media/renesas,csi2.txt index 331409259752..331409259752 100644 --- a/Documentation/devicetree/bindings/media/renesas,rcar-csi2.txt +++ b/Documentation/devicetree/bindings/media/renesas,csi2.txt diff --git a/Documentation/devicetree/bindings/media/rcar_imr.txt b/Documentation/devicetree/bindings/media/renesas,imr.txt index b0614153ed36..b0614153ed36 100644 --- a/Documentation/devicetree/bindings/media/rcar_imr.txt +++ b/Documentation/devicetree/bindings/media/renesas,imr.txt diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/renesas,vin.txt index aa217b096279..aa217b096279 100644 --- a/Documentation/devicetree/bindings/media/rcar_vin.txt +++ b/Documentation/devicetree/bindings/media/renesas,vin.txt diff --git a/Documentation/devicetree/bindings/media/rockchip-vpu.txt b/Documentation/devicetree/bindings/media/rockchip-vpu.txt index 35dc464ad7c8..339252d9c515 100644 --- a/Documentation/devicetree/bindings/media/rockchip-vpu.txt +++ b/Documentation/devicetree/bindings/media/rockchip-vpu.txt @@ -1,14 +1,17 @@ device-tree bindings for rockchip VPU codec Rockchip (Video Processing Unit) present in various Rockchip platforms, -such as RK3288 and RK3399. +such as RK3288, RK3328 and RK3399. Required properties: - compatible: value should be one of the following "rockchip,rk3288-vpu"; + "rockchip,rk3328-vpu"; "rockchip,rk3399-vpu"; - interrupts: encoding and decoding interrupt specifiers -- interrupt-names: should be "vepu" and "vdpu" +- interrupt-names: should be + "vepu", "vdpu" on RK3288 and RK3399, + "vdpu" on RK3328. - clocks: phandle to VPU aclk, hclk clocks - clock-names: should be "aclk" and "hclk" - power-domains: phandle to power domain node @@ -27,3 +30,14 @@ SoC-specific DT entry: power-domains = <&power RK3288_PD_VIDEO>; iommus = <&vpu_mmu>; }; + + vpu: video-codec@ff350000 { + compatible = "rockchip,rk3328-vpu"; + reg = <0x0 0xff350000 0x0 0x800>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "vdpu"; + clocks = <&cru ACLK_VPU>, <&cru HCLK_VPU>; + clock-names = "aclk", "hclk"; + power-domains = <&power RK3328_PD_VPU>; + iommus = <&vpu_mmu>; + }; diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt b/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt index 249790a93017..3122ded82eb4 100644 --- a/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt +++ b/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt @@ -11,7 +11,7 @@ Required properties: - clock-names: must contain "mclk", which is the DCMI peripherial clock - pinctrl: the pincontrol settings to configure muxing properly for pins that connect to DCMI device. - See Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt. + See Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml. - dmas: phandle to DMA controller node, see Documentation/devicetree/bindings/dma/stm32-dma.txt - dma-names: must contain "tx", which is the transmit channel from DCMI to DMA diff --git a/Documentation/devicetree/bindings/media/sun6i-csi.txt b/Documentation/devicetree/bindings/media/sun6i-csi.txt index 0dd540bb03db..a2e3e56f0257 100644 --- a/Documentation/devicetree/bindings/media/sun6i-csi.txt +++ b/Documentation/devicetree/bindings/media/sun6i-csi.txt @@ -6,6 +6,7 @@ Allwinner V3s SoC features a CSI module(CSI1) with parallel interface. Required properties: - compatible: value must be one of: * "allwinner,sun6i-a31-csi" + * "allwinner,sun8i-a83t-csi" * "allwinner,sun8i-h3-csi" * "allwinner,sun8i-v3s-csi" * "allwinner,sun50i-a64-csi" diff --git a/Documentation/devicetree/bindings/media/sunxi-ir.txt b/Documentation/devicetree/bindings/media/sunxi-ir.txt deleted file mode 100644 index 278098987edb..000000000000 --- a/Documentation/devicetree/bindings/media/sunxi-ir.txt +++ /dev/null @@ -1,28 +0,0 @@ -Device-Tree bindings for SUNXI IR controller found in sunXi SoC family - -Required properties: -- compatible : "allwinner,sun4i-a10-ir" or "allwinner,sun5i-a13-ir" -- clocks : list of clock specifiers, corresponding to - entries in clock-names property; -- clock-names : should contain "apb" and "ir" entries; -- interrupts : should contain IR IRQ number; -- reg : should contain IO map address for IR. - -Optional properties: -- linux,rc-map-name: see rc.txt file in the same directory. -- resets : phandle + reset specifier pair -- clock-frequency : IR Receiver clock frequency, in Hertz. Defaults to 8 MHz - if missing. - -Example: - -ir0: ir@1c21800 { - compatible = "allwinner,sun4i-a10-ir"; - clocks = <&apb0_gates 6>, <&ir0_clk>; - clock-names = "apb", "ir"; - clock-frequency = <3000000>; - resets = <&apb0_rst 1>; - interrupts = <0 5 1>; - reg = <0x01C21800 0x40>; - linux,rc-map-name = "rc-rc6-mce"; -}; diff --git a/Documentation/devicetree/bindings/memory-controllers/ingenic,jz4780-nemc.txt b/Documentation/devicetree/bindings/memory-controllers/ingenic,jz4780-nemc.txt index f936b5589b19..59b8dcc118ee 100644 --- a/Documentation/devicetree/bindings/memory-controllers/ingenic,jz4780-nemc.txt +++ b/Documentation/devicetree/bindings/memory-controllers/ingenic,jz4780-nemc.txt @@ -5,6 +5,7 @@ controller in Ingenic JZ4780 Required properties: - compatible: Should be set to one of: + "ingenic,jz4740-nemc" (JZ4740) "ingenic,jz4780-nemc" (JZ4780) - reg: Should specify the NEMC controller registers location and length. - clocks: Clock for the NEMC controller. diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt index e937ddd871a6..b478ade4da65 100644 --- a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt +++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt @@ -2,9 +2,10 @@ SMI (Smart Multimedia Interface) Common The hardware block diagram please check bindings/iommu/mediatek,iommu.txt -Mediatek SMI have two generations of HW architecture, mt2712 and mt8173 use -the second generation of SMI HW while mt2701 uses the first generation HW of -SMI. +Mediatek SMI have two generations of HW architecture, here is the list +which generation the SoCs use: +generation 1: mt2701 and mt7623. +generation 2: mt2712, mt8173 and mt8183. There's slight differences between the two SMI, for generation 2, the register which control the iommu port is at each larb's register base. But @@ -19,6 +20,7 @@ Required properties: "mediatek,mt2712-smi-common" "mediatek,mt7623-smi-common", "mediatek,mt2701-smi-common" "mediatek,mt8173-smi-common" + "mediatek,mt8183-smi-common" - reg : the register and size of the SMI block. - power-domains : a phandle to the power domain of this local arbiter. - clocks : Must contain an entry for each entry in clock-names. @@ -30,6 +32,10 @@ Required properties: They may be the same if both source clocks are the same. - "async" : asynchronous clock, it help transform the smi clock into the emi clock domain, this clock is only needed by generation 1 smi HW. + and these 2 option clocks for generation 2 smi HW: + - "gals0": the path0 clock of GALS(Global Async Local Sync). + - "gals1": the path1 clock of GALS(Global Async Local Sync). + Here is the list which has this GALS: mt8183. Example: smi_common: smi@14022000 { diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt index 94eddcae77ab..4b369b3e1a69 100644 --- a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt +++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt @@ -8,6 +8,7 @@ Required properties: "mediatek,mt2712-smi-larb" "mediatek,mt7623-smi-larb", "mediatek,mt2701-smi-larb" "mediatek,mt8173-smi-larb" + "mediatek,mt8183-smi-larb" - reg : the register and size of this local arbiter. - mediatek,smi : a phandle to the smi_common node. - power-domains : a phandle to the power domain of this local arbiter. @@ -16,6 +17,9 @@ Required properties: - "apb" : Advanced Peripheral Bus clock, It's the clock for setting the register. - "smi" : It's the clock for transfer data and command. + and this optional clock name: + - "gals": the clock for GALS(Global Async Local Sync). + Here is the list which has this GALS: mt8183. Required property for mt2701, mt2712 and mt7623: - mediatek,larb-id :the hardware id of this larb. diff --git a/Documentation/devicetree/bindings/memory-controllers/renesas-memory-controllers.txt b/Documentation/devicetree/bindings/memory-controllers/renesas,dbsc.txt index 9f78e6c82740..9f78e6c82740 100644 --- a/Documentation/devicetree/bindings/memory-controllers/renesas-memory-controllers.txt +++ b/Documentation/devicetree/bindings/memory-controllers/renesas,dbsc.txt diff --git a/Documentation/devicetree/bindings/mfd/allwinner,sun4i-a10-ts.yaml b/Documentation/devicetree/bindings/mfd/allwinner,sun4i-a10-ts.yaml new file mode 100644 index 000000000000..4b1a09acb98b --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/allwinner,sun4i-a10-ts.yaml @@ -0,0 +1,76 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/allwinner,sun4i-a10-ts.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 Resistive Touchscreen Controller Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + "#thermal-sensor-cells": + const: 0 + + compatible: + enum: + - allwinner,sun4i-a10-ts + - allwinner,sun5i-a13-ts + - allwinner,sun6i-a31-ts + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + allwinner,ts-attached: + $ref: /schemas/types.yaml#/definitions/flag + description: A touchscreen is attached to the controller + + allwinner,tp-sensitive-adjust: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - minimum: 0 + maximum: 15 + default: 15 + description: Sensitivity of pen down detection + + allwinner,filter-type: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - minimum: 0 + maximum: 3 + default: 1 + description: | + Select median and averaging filter. Sample used for median / + averaging filter: + 0: 4/2 + 1: 5/3 + 2: 8/4 + 3: 16/8 + +required: + - "#thermal-sensor-cells" + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + rtp: rtp@1c25000 { + compatible = "allwinner,sun4i-a10-ts"; + reg = <0x01c25000 0x100>; + interrupts = <29>; + allwinner,ts-attached; + #thermal-sensor-cells = <0>; + /* sensitive/noisy touch panel */ + allwinner,tp-sensitive-adjust = <0>; + allwinner,filter-type = <3>; + }; + +... diff --git a/Documentation/devicetree/bindings/mfd/aspeed-scu.txt b/Documentation/devicetree/bindings/mfd/aspeed-scu.txt index ce8cf0ec6279..4d92c0bb6687 100644 --- a/Documentation/devicetree/bindings/mfd/aspeed-scu.txt +++ b/Documentation/devicetree/bindings/mfd/aspeed-scu.txt @@ -4,9 +4,7 @@ configuring elements such as clocks, pinmux, and reset. Required properties: - compatible: One of: "aspeed,ast2400-scu", "syscon", "simple-mfd" - "aspeed,g4-scu", "syscon", "simple-mfd" "aspeed,ast2500-scu", "syscon", "simple-mfd" - "aspeed,g5-scu", "syscon", "simple-mfd" - reg: contains the offset and length of the SCU memory region - #clock-cells: should be set to <1> - the system controller is also a diff --git a/Documentation/devicetree/bindings/mfd/atmel-usart.txt b/Documentation/devicetree/bindings/mfd/atmel-usart.txt index 7f0cd72f47d2..699fd3c9ace8 100644 --- a/Documentation/devicetree/bindings/mfd/atmel-usart.txt +++ b/Documentation/devicetree/bindings/mfd/atmel-usart.txt @@ -17,17 +17,24 @@ Required properties for USART in SPI mode: - cs-gpios: chipselects (internal cs not supported) - atmel,usart-mode : Must be <AT91_USART_MODE_SPI> (found in dt-bindings/mfd/at91-usart.h) +Optional properties in serial and SPI mode: +- dma bindings for dma transfer: + - dmas: DMA specifier, consisting of a phandle to DMA controller node, + memory peripheral interface and USART DMA channel ID, FIFO configuration. + The order of DMA channels is fixed. The first DMA channel must be TX + associated channel and the second one must be RX associated channel. + Refer to dma.txt and atmel-dma.txt for details. + - dma-names: "tx" for TX channel. + "rx" for RX channel. + The order of dma-names is also fixed. The first name must be "tx" + and the second one must be "rx" as in the examples below. + Optional properties in serial mode: - atmel,use-dma-rx: use of PDC or DMA for receiving data - atmel,use-dma-tx: use of PDC or DMA for transmitting data - {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD line respectively. It will use specified PIO instead of the peripheral function pin for the USART feature. If unsure, don't specify this property. -- add dma bindings for dma transfer: - - dmas: DMA specifier, consisting of a phandle to DMA controller node, - memory peripheral interface and USART DMA channel ID, FIFO configuration. - Refer to dma.txt and atmel-dma.txt for details. - - dma-names: "rx" for RX channel, "tx" for TX channel. - atmel,fifo-size: maximum number of data the RX and TX FIFOs can store for FIFO capable USARTs. - rs485-rts-delay, rs485-rx-during-tx, linux,rs485-enabled-at-boot-time: see rs485.txt @@ -81,5 +88,8 @@ Example: interrupts = <12 IRQ_TYPE_LEVEL_HIGH 5>; clocks = <&usart0_clk>; clock-names = "usart"; + dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(3)>, + <&dma0 2 (AT91_DMA_CFG_PER_ID(4) | AT91_DMA_CFG_FIFOCFG_ASAP)>; + dma-names = "tx", "rx"; cs-gpios = <&pioB 3 0>; }; diff --git a/Documentation/devicetree/bindings/mfd/cros-ec.txt b/Documentation/devicetree/bindings/mfd/cros-ec.txt index 6245c9b1a68b..4860eabd0f72 100644 --- a/Documentation/devicetree/bindings/mfd/cros-ec.txt +++ b/Documentation/devicetree/bindings/mfd/cros-ec.txt @@ -3,7 +3,7 @@ ChromeOS Embedded Controller Google's ChromeOS EC is a Cortex-M device which talks to the AP and implements various function such as keyboard and battery charging. -The EC can be connect through various means (I2C, SPI, LPC) and the +The EC can be connect through various means (I2C, SPI, LPC, RPMSG) and the compatible string used depends on the interface. Each connection method has its own driver which connects to the top level interface-agnostic EC driver. Other Linux driver (such as cros-ec-keyb for the matrix keyboard) connect to @@ -17,6 +17,9 @@ Required properties (SPI): - compatible: "google,cros-ec-spi" - reg: SPI chip select +Required properties (RPMSG): +- compatible: "google,cros-ec-rpmsg" + Optional properties (SPI): - google,cros-ec-spi-pre-delay: Some implementations of the EC need a little time to wake up from sleep before they can receive SPI transfers at a high diff --git a/Documentation/devicetree/bindings/mfd/lp87565.txt b/Documentation/devicetree/bindings/mfd/lp87565.txt index a48df7c08ab0..41671e0dc26b 100644 --- a/Documentation/devicetree/bindings/mfd/lp87565.txt +++ b/Documentation/devicetree/bindings/mfd/lp87565.txt @@ -41,3 +41,39 @@ lp87565_pmic: pmic@60 { }; }; }; + +TI LP87561 PMIC: + +This is a single output 4-phase regulator configuration + +Required properties: + - compatible: "ti,lp87561-q1" + - reg: I2C slave address. + - gpio-controller: Marks the device node as a GPIO Controller. + - #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../gpio/gpio.txt for more information. + - xxx-in-supply: Phandle to parent supply node of each regulator + populated under regulators node. xxx should match + the supply_name populated in driver. +Example: + +lp87561_pmic: pmic@62 { + compatible = "ti,lp87561-q1"; + reg = <0x62>; + gpio-controller; + #gpio-cells = <2>; + + buck3210-in-supply = <&vsys_3v3>; + + regulators: regulators { + buck3210_reg: buck3210 { + /* VDD_CORE */ + regulator-name = "buck3210"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-always-on; + regulator-boot-on; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/madera.txt b/Documentation/devicetree/bindings/mfd/madera.txt index db3266088386..cad0f2800502 100644 --- a/Documentation/devicetree/bindings/mfd/madera.txt +++ b/Documentation/devicetree/bindings/mfd/madera.txt @@ -11,10 +11,14 @@ bindings/sound/madera.txt Required properties: - compatible : One of the following chip-specific strings: + "cirrus,cs47l15" "cirrus,cs47l35" "cirrus,cs47l85" "cirrus,cs47l90" "cirrus,cs47l91" + "cirrus,cs42l92" + "cirrus,cs47l92" + "cirrus,cs47l93" "cirrus,wm1840" - reg : I2C slave address when connected using I2C, chip select number when @@ -22,7 +26,7 @@ Required properties: - DCVDD-supply : Power supply for the device as defined in bindings/regulator/regulator.txt - Mandatory on CS47L35, CS47L90, CS47L91 + Mandatory on CS47L15, CS47L35, CS47L90, CS47L91, CS42L92, CS47L92, CS47L93 Optional on CS47L85, WM1840 - AVDD-supply, DBVDD1-supply, DBVDD2-supply, CPVDD1-supply, CPVDD2-supply : @@ -35,7 +39,7 @@ Required properties: (CS47L85, WM1840) - SPKVDD-supply : Power supply for the device - (CS47L35) + (CS47L15, CS47L35) - interrupt-controller : Indicates that this device is an interrupt controller diff --git a/Documentation/devicetree/bindings/mfd/mt6397.txt b/Documentation/devicetree/bindings/mfd/mt6397.txt index 0ebd08af777d..a9b105ac00a8 100644 --- a/Documentation/devicetree/bindings/mfd/mt6397.txt +++ b/Documentation/devicetree/bindings/mfd/mt6397.txt @@ -8,11 +8,12 @@ MT6397/MT6323 is a multifunction device with the following sub modules: - Clock - LED - Keys +- Power controller It is interfaced to host controller using SPI interface by a proprietary hardware called PMIC wrapper or pwrap. MT6397/MT6323 MFD is a child device of pwrap. See the following for pwarp node definitions: -Documentation/devicetree/bindings/soc/mediatek/pwrap.txt +../soc/mediatek/pwrap.txt This document describes the binding for MFD device and its sub module. @@ -22,14 +23,16 @@ compatible: "mediatek,mt6397" or "mediatek,mt6323" Optional subnodes: - rtc - Required properties: + Required properties: Should be one of follows + - compatible: "mediatek,mt6323-rtc" - compatible: "mediatek,mt6397-rtc" + For details, see ../rtc/rtc-mt6397.txt - regulators Required properties: - compatible: "mediatek,mt6397-regulator" - see Documentation/devicetree/bindings/regulator/mt6397-regulator.txt + see ../regulator/mt6397-regulator.txt - compatible: "mediatek,mt6323-regulator" - see Documentation/devicetree/bindings/regulator/mt6323-regulator.txt + see ../regulator/mt6323-regulator.txt - codec Required properties: - compatible: "mediatek,mt6397-codec" @@ -39,12 +42,17 @@ Optional subnodes: - led Required properties: - compatible: "mediatek,mt6323-led" - see Documentation/devicetree/bindings/leds/leds-mt6323.txt + see ../leds/leds-mt6323.txt - keys Required properties: - compatible: "mediatek,mt6397-keys" or "mediatek,mt6323-keys" - see Documentation/devicetree/bindings/input/mtk-pmic-keys.txt + see ../input/mtk-pmic-keys.txt + +- power-controller + Required properties: + - compatible: "mediatek,mt6323-pwrc" + For details, see ../power/reset/mt6323-poweroff.txt Example: pwrap: pwrap@1000f000 { diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt index 1683ec3245bc..04df07f6f793 100644 --- a/Documentation/devicetree/bindings/mfd/rk808.txt +++ b/Documentation/devicetree/bindings/mfd/rk808.txt @@ -3,11 +3,15 @@ RK8XX Power Management Integrated Circuit The rk8xx family current members: rk805 rk808 +rk809 +rk817 rk818 Required properties: - compatible: "rockchip,rk805" - compatible: "rockchip,rk808" +- compatible: "rockchip,rk809" +- compatible: "rockchip,rk817" - compatible: "rockchip,rk818" - reg: I2C slave address - interrupts: the interrupt outputs of the controller. @@ -45,6 +49,23 @@ Optional RK808 properties: the gpio controller. If DVS GPIOs aren't present, voltage changes will happen very quickly with no slow ramp time. +Optional shared RK809 and RK817 properties: +- vcc1-supply: The input supply for DCDC_REG1 +- vcc2-supply: The input supply for DCDC_REG2 +- vcc3-supply: The input supply for DCDC_REG3 +- vcc4-supply: The input supply for DCDC_REG4 +- vcc5-supply: The input supply for LDO_REG1, LDO_REG2, LDO_REG3 +- vcc6-supply: The input supply for LDO_REG4, LDO_REG5, LDO_REG6 +- vcc7-supply: The input supply for LDO_REG7, LDO_REG8, LDO_REG9 + +Optional RK809 properties: +- vcc8-supply: The input supply for SWITCH_REG1 +- vcc9-supply: The input supply for DCDC_REG5, SWITCH_REG2 + +Optional RK817 properties: +- vcc8-supply: The input supply for BOOST +- vcc9-supply: The input supply for OTG_SWITCH + Optional RK818 properties: - vcc1-supply: The input supply for DCDC_REG1 - vcc2-supply: The input supply for DCDC_REG2 @@ -86,6 +107,21 @@ number as described in RK808 datasheet. - SWITCH_REGn - valid values for n are 1 to 2 +Following regulators of the RK809 and RK817 PMIC blocks are supported. Note that +the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO +number as described in RK809 and RK817 datasheets. + + - DCDC_REGn + - valid values for n are 1 to 5 for RK809. + - valid values for n are 1 to 4 for RK817. + - LDO_REGn + - valid values for n are 1 to 9 for RK809. + - valid values for n are 1 to 9 for RK817. + - SWITCH_REGn + - valid values for n are 1 to 2 for RK809. + - BOOST for RK817 + - OTG_SWITCH for RK817 + Following regulators of the RK818 PMIC block are supported. Note that the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO number as described in RK818 datasheet. @@ -98,6 +134,14 @@ number as described in RK818 datasheet. - HDMI_SWITCH - OTG_SWITCH +It is necessary to configure three pins for both the RK809 and RK817, the three +pins are "gpio_ts" "gpio_gt" "gpio_slp". + The gpio_gt and gpio_ts pins support the gpio function. + The gpio_slp pin is for controlling the pmic states, as below: + - reset + - power down + - sleep + Standard regulator bindings are used inside regulator subnodes. Check Documentation/devicetree/bindings/regulator/regulator.txt for more details diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt index 65c23263cc54..b74e5e94d1cb 100644 --- a/Documentation/devicetree/bindings/mfd/rn5t618.txt +++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt @@ -14,6 +14,10 @@ Required properties: "ricoh,rc5t619" - reg: the I2C slave address of the device +Optional properties: + - system-power-controller: + See Documentation/devicetree/bindings/power/power-controller.txt + Sub-nodes: - regulators: the node is required if the regulator functionality is needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, DCDC4 @@ -28,6 +32,7 @@ Example: pmic@32 { compatible = "ricoh,rn5t618"; reg = <0x32>; + system-power-controller; regulators { DCDC1 { diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd70528-pmic.txt b/Documentation/devicetree/bindings/mfd/rohm,bd70528-pmic.txt new file mode 100644 index 000000000000..c3c02ce73cde --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/rohm,bd70528-pmic.txt @@ -0,0 +1,102 @@ +* ROHM BD70528 Power Management Integrated Circuit bindings + +BD70528MWV is an ultra-low quiescent current general purpose, single-chip, +power management IC for battery-powered portable devices. The IC +integrates 3 ultra-low current consumption buck converters, 3 LDOs and 2 +LED Drivers. Also included are 4 GPIOs, a real-time clock (RTC), a 32kHz +clock gate, high-accuracy VREF for use with an external ADC, flexible +dual-input power path, 10 bit SAR ADC for battery temperature monitor and +1S battery charger with scalable charge currents. + +Required properties: + - compatible : Should be "rohm,bd70528" + - reg : I2C slave address. + - interrupts : The interrupt line the device is connected to. + - interrupt-controller : To indicate BD70528 acts as an interrupt controller. + - #interrupt-cells : Should be 2. Usage is compliant to the 2 cells + variant of ../interrupt-controller/interrupts.txt + - gpio-controller : To indicate BD70528 acts as a GPIO controller. + - #gpio-cells : Should be 2. The first cell is the pin number and + the second cell is used to specify flags. See + ../gpio/gpio.txt for more information. + - #clock-cells : Should be 0. + - regulators: : List of child nodes that specify the regulators. + Please see ../regulator/rohm,bd70528-regulator.txt + +Optional properties: + - clock-output-names : Should contain name for output clock. + +Example: +/* External oscillator */ +osc: oscillator { + compatible = "fixed-clock"; + #clock-cells = <1>; + clock-frequency = <32768>; + clock-output-names = "osc"; +}; + +pmic: pmic@4b { + compatible = "rohm,bd70528"; + reg = <0x4b>; + interrupt-parent = <&gpio1>; + interrupts = <29 GPIO_ACTIVE_LOW>; + clocks = <&osc 0>; + #clock-cells = <0>; + clock-output-names = "bd70528-32k-out"; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + + regulators { + buck1: BUCK1 { + regulator-name = "buck1"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + regulator-ramp-delay = <125>; + }; + buck2: BUCK2 { + regulator-name = "buck2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-ramp-delay = <125>; + }; + buck3: BUCK3 { + regulator-name = "buck3"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-ramp-delay = <250>; + }; + ldo1: LDO1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + ldo2: LDO2 { + regulator-name = "ldo2"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + ldo3: LDO3 { + regulator-name = "ldo3"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <3300000>; + }; + led_ldo1: LED_LDO1 { + regulator-name = "led_ldo1"; + regulator-min-microvolt = <200000>; + regulator-max-microvolt = <300000>; + }; + led_ldo2: LED_LDO2 { + regulator-name = "led_ldo2"; + regulator-min-microvolt = <200000>; + regulator-max-microvolt = <300000>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt index d5f68ac78d15..f22d74c7a8db 100644 --- a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt +++ b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt @@ -8,6 +8,8 @@ and 6 LDOs. Datasheet for BD71837 is available at: https://www.rohm.com/datasheet/BD71837MWV/bd71837mwv-e +Datasheet for BD71847 is available at: +https://www.rohm.com/datasheet/BD71847AMWV/bd71847amwv-e Required properties: - compatible : Should be "rohm,bd71837" for bd71837 @@ -38,6 +40,14 @@ target state is set to READY by default. If SNVS state is used the boot crucial regulators must have the regulator-always-on and regulator-boot-on properties set in regulator node. +- rohm,short-press-ms : Short press duration in milliseconds +- rohm,long-press-ms : Long press duration in milliseconds + +Configure the "short press" and "long press" timers for the power button. +Values are rounded to what hardware supports (500ms multiple for short and +1000ms multiple for long). If these properties are not present the existing +configuration (from bootloader or OTP) is not touched. + Example: /* external oscillator node */ diff --git a/Documentation/devicetree/bindings/mfd/sun4i-gpadc.txt b/Documentation/devicetree/bindings/mfd/sun4i-gpadc.txt deleted file mode 100644 index 86dd8191b04c..000000000000 --- a/Documentation/devicetree/bindings/mfd/sun4i-gpadc.txt +++ /dev/null @@ -1,59 +0,0 @@ -Allwinner SoCs' GPADC Device Tree bindings ------------------------------------------- -The Allwinner SoCs all have an ADC that can also act as a thermal sensor -and sometimes as a touchscreen controller. - -Required properties: - - compatible: "allwinner,sun8i-a33-ths", - - reg: mmio address range of the chip, - - #thermal-sensor-cells: shall be 0, - - #io-channel-cells: shall be 0, - -Example: - ths: ths@1c25000 { - compatible = "allwinner,sun8i-a33-ths"; - reg = <0x01c25000 0x100>; - #thermal-sensor-cells = <0>; - #io-channel-cells = <0>; - }; - -sun4i, sun5i and sun6i SoCs are also supported via the older binding: - -sun4i resistive touchscreen controller --------------------------------------- - -Required properties: - - compatible: "allwinner,sun4i-a10-ts", "allwinner,sun5i-a13-ts" or - "allwinner,sun6i-a31-ts" - - reg: mmio address range of the chip - - interrupts: interrupt to which the chip is connected - - #thermal-sensor-cells: shall be 0 - -Optional properties: - - allwinner,ts-attached : boolean indicating that an actual touchscreen - is attached to the controller - - allwinner,tp-sensitive-adjust : integer (4 bits) - adjust sensitivity of pen down detection - between 0 (least sensitive) and 15 - (defaults to 15) - - allwinner,filter-type : integer (2 bits) - select median and averaging filter - samples used for median / averaging filter - 0: 4/2 - 1: 5/3 - 2: 8/4 - 3: 16/8 - (defaults to 1) - -Example: - - rtp: rtp@1c25000 { - compatible = "allwinner,sun4i-a10-ts"; - reg = <0x01c25000 0x100>; - interrupts = <29>; - allwinner,ts-attached; - #thermal-sensor-cells = <0>; - /* sensitive/noisy touch panel */ - allwinner,tp-sensitive-adjust = <0>; - allwinner,filter-type = <3>; - }; diff --git a/Documentation/devicetree/bindings/mfd/ti-lmu.txt b/Documentation/devicetree/bindings/mfd/ti-lmu.txt index 86ca786d54fc..2296b8f24de4 100644 --- a/Documentation/devicetree/bindings/mfd/ti-lmu.txt +++ b/Documentation/devicetree/bindings/mfd/ti-lmu.txt @@ -8,7 +8,7 @@ TI LMU driver supports lighting devices below. LM3632 Backlight and regulator LM3633 Backlight, LED and fault monitor LM3695 Backlight - LM3697 Backlight and fault monitor + LM36274 Backlight and regulator Required properties: - compatible: Should be one of: @@ -16,15 +16,32 @@ Required properties: "ti,lm3632" "ti,lm3633" "ti,lm3695" - "ti,lm3697" + "ti,lm36274" - reg: I2C slave address. 0x11 for LM3632 0x29 for LM3631 - 0x36 for LM3633, LM3697 + 0x36 for LM3633 0x63 for LM3695 + 0x11 for LM36274 -Optional property: +Optional properties: - enable-gpios: A GPIO specifier for hardware enable pin. + - ramp-up-us: Current ramping from one brightness level to + the a higher brightness level. + Range from 2048 us - 117.44 s + - ramp-down-us: Current ramping from one brightness level to + the a lower brightness level. + Range from 2048 us - 117.44 s + - ti,brightness-resolution - This determines whether to use 8 bit brightness + mode or 11 bit brightness mode. If this value is + not set the device is defaulted to the preferred + 8bit brightness mode per 7.3.4.1 of the data + sheet. This setting can either be in the parent + node or as part of the LED child nodes. This + is determined by the part itself if the strings + have a common brightness register or individual + brightness registers. + The values are 255 (8bit) or 2047 (11bit). Required node: - backlight: All LMU devices have backlight child nodes. @@ -35,14 +52,15 @@ Optional nodes: Required properties: - compatible: Should be one of: "ti,lm3633-fault-monitor" - "ti,lm3697-fault-monitor" - leds: LED properties for LM3633. Please refer to [2]. + LED properties for LM36274. Please refer to [4]. - regulators: Regulator properties for LM3631 and LM3632. Please refer to [3]. [1] ../leds/backlight/ti-lmu-backlight.txt [2] ../leds/leds-lm3633.txt [3] ../regulator/lm363x-regulator.txt +[4] ../leds/leds-lm36274.txt lm3631@29 { compatible = "ti,lm3631"; @@ -90,7 +108,7 @@ lm3631@29 { lcd_bl { led-sources = <0 1>; - ramp-up-msec = <300>; + ramp-up-us = <300000>; }; }; }; @@ -152,15 +170,15 @@ lm3633@36 { main { label = "main_lcd"; led-sources = <1 2>; - ramp-up-msec = <500>; - ramp-down-msec = <500>; + ramp-up-us = <500000>; + ramp-down-us = <500000>; }; front { label = "front_lcd"; led-sources = <0>; - ramp-up-msec = <1000>; - ramp-down-msec = <0>; + ramp-up-us = <1000000>; + ramp-down-us = <0>; }; }; @@ -201,23 +219,51 @@ lm3695@63 { }; }; -lm3697@36 { - compatible = "ti,lm3697"; - reg = <0x36>; +lm36274@11 { + compatible = "ti,lm36274"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11>; enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>; + regulators { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,lm363x-regulator"; - backlight { - compatible = "ti,lm3697-backlight"; + enable-gpios = <&pioC 0 GPIO_ACTIVE_HIGH>, + <&pioC 1 GPIO_ACTIVE_HIGH>; - lcd { - led-sources = <0 1 2>; - ramp-up-msec = <200>; - ramp-down-msec = <200>; + vboost { + regulator-name = "lcd_boost"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <7150000>; + regulator-always-on; + }; + + vpos { + regulator-name = "lcd_vpos"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6500000>; + }; + + vneg { + regulator-name = "lcd_vneg"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6500000>; }; }; - fault-monitor { - compatible = "ti,lm3697-fault-monitor"; + backlight { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,lm36274-backlight"; + + led@0 { + reg = <0>; + led-sources = <0 2>; + label = "white:backlight_cluster"; + linux,default-trigger = "backlight"; + }; }; }; diff --git a/Documentation/devicetree/bindings/misc/aspeed-p2a-ctrl.txt b/Documentation/devicetree/bindings/misc/aspeed-p2a-ctrl.txt index 854bd67ffec6..0e1fa5bc6a30 100644 --- a/Documentation/devicetree/bindings/misc/aspeed-p2a-ctrl.txt +++ b/Documentation/devicetree/bindings/misc/aspeed-p2a-ctrl.txt @@ -26,9 +26,7 @@ property: - compatible : Should be one of the following: "aspeed,ast2400-scu", "syscon", "simple-mfd" - "aspeed,g4-scu", "syscon", "simple-mfd" "aspeed,ast2500-scu", "syscon", "simple-mfd" - "aspeed,g5-scu", "syscon", "simple-mfd" Example =================== diff --git a/Documentation/devicetree/bindings/misc/fsl,dpaa2-console.txt b/Documentation/devicetree/bindings/misc/fsl,dpaa2-console.txt new file mode 100644 index 000000000000..1442ba5d2d98 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/fsl,dpaa2-console.txt @@ -0,0 +1,11 @@ +DPAA2 console support + +Required properties: + + - compatible + Value type: <string> + Definition: Must be "fsl,dpaa2-console". + - reg + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the region where the MCFBA + (MC firmware base address) register can be found. diff --git a/Documentation/devicetree/bindings/misc/intel,ixp4xx-queue-manager.yaml b/Documentation/devicetree/bindings/misc/intel,ixp4xx-ahb-queue-manager.yaml index d2313b1d9405..0ea21a6f70b4 100644 --- a/Documentation/devicetree/bindings/misc/intel,ixp4xx-queue-manager.yaml +++ b/Documentation/devicetree/bindings/misc/intel,ixp4xx-ahb-queue-manager.yaml @@ -2,7 +2,7 @@ # Copyright 2019 Linaro Ltd. %YAML 1.2 --- -$id: "http://devicetree.org/schemas/misc/intel-ixp4xx-ahb-queue-manager.yaml#" +$id: "http://devicetree.org/schemas/misc/intel,ixp4xx-ahb-queue-manager.yaml#" $schema: "http://devicetree.org/meta-schemas/core.yaml#" title: Intel IXP4xx AHB Queue Manager diff --git a/Documentation/devicetree/bindings/misc/olpc,xo1.75-ec.txt b/Documentation/devicetree/bindings/misc/olpc,xo1.75-ec.txt new file mode 100644 index 000000000000..8c4d649cdd8f --- /dev/null +++ b/Documentation/devicetree/bindings/misc/olpc,xo1.75-ec.txt @@ -0,0 +1,23 @@ +OLPC XO-1.75 Embedded Controller + +Required properties: +- compatible: Should be "olpc,xo1.75-ec". +- cmd-gpios: gpio specifier of the CMD pin + +The embedded controller requires the SPI controller driver to signal readiness +to receive a transfer (that is, when TX FIFO contains the response data) by +strobing the ACK pin with the ready signal. See the "ready-gpios" property of the +SSP binding as documented in: +<Documentation/devicetree/bindings/spi/spi-pxa2xx.txt>. + +Example: + &ssp3 { + spi-slave; + ready-gpios = <&gpio 125 GPIO_ACTIVE_HIGH>; + + slave { + compatible = "olpc,xo1.75-ec"; + spi-cpha; + cmd-gpios = <&gpio 155 GPIO_ACTIVE_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/misc/xlnx,sd-fec.txt b/Documentation/devicetree/bindings/misc/xlnx,sd-fec.txt new file mode 100644 index 000000000000..e3289634fa30 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/xlnx,sd-fec.txt @@ -0,0 +1,58 @@ +* Xilinx SDFEC(16nm) IP * + +The Soft Decision Forward Error Correction (SDFEC) Engine is a Hard IP block +which provides high-throughput LDPC and Turbo Code implementations. +The LDPC decode & encode functionality is capable of covering a range of +customer specified Quasi-cyclic (QC) codes. The Turbo decode functionality +principally covers codes used by LTE. The FEC Engine offers significant +power and area savings versus implementations done in the FPGA fabric. + + +Required properties: +- compatible: Must be "xlnx,sd-fec-1.1" +- clock-names : List of input clock names from the following: + - "core_clk", Main processing clock for processing core (required) + - "s_axi_aclk", AXI4-Lite memory-mapped slave interface clock (required) + - "s_axis_din_aclk", DIN AXI4-Stream Slave interface clock (optional) + - "s_axis_din_words-aclk", DIN_WORDS AXI4-Stream Slave interface clock (optional) + - "s_axis_ctrl_aclk", Control input AXI4-Stream Slave interface clock (optional) + - "m_axis_dout_aclk", DOUT AXI4-Stream Master interface clock (optional) + - "m_axis_dout_words_aclk", DOUT_WORDS AXI4-Stream Master interface clock (optional) + - "m_axis_status_aclk", Status output AXI4-Stream Master interface clock (optional) +- clocks : Clock phandles (see clock_bindings.txt for details). +- reg: Should contain Xilinx SDFEC 16nm Hardened IP block registers + location and length. +- xlnx,sdfec-code : Should contain "ldpc" or "turbo" to describe the codes + being used. +- xlnx,sdfec-din-words : A value 0 indicates that the DIN_WORDS interface is + driven with a fixed value and is not present on the device, a value of 1 + configures the DIN_WORDS to be block based, while a value of 2 configures the + DIN_WORDS input to be supplied for each AXI transaction. +- xlnx,sdfec-din-width : Configures the DIN AXI stream where a value of 1 + configures a width of "1x128b", 2 a width of "2x128b" and 4 configures a width + of "4x128b". +- xlnx,sdfec-dout-words : A value 0 indicates that the DOUT_WORDS interface is + driven with a fixed value and is not present on the device, a value of 1 + configures the DOUT_WORDS to be block based, while a value of 2 configures the + DOUT_WORDS input to be supplied for each AXI transaction. +- xlnx,sdfec-dout-width : Configures the DOUT AXI stream where a value of 1 + configures a width of "1x128b", 2 a width of "2x128b" and 4 configures a width + of "4x128b". +Optional properties: +- interrupts: should contain SDFEC interrupt number + +Example +--------------------------------------- + sd_fec_0: sd-fec@a0040000 { + compatible = "xlnx,sd-fec-1.1"; + clock-names = "core_clk","s_axi_aclk","s_axis_ctrl_aclk","s_axis_din_aclk","m_axis_status_aclk","m_axis_dout_aclk"; + clocks = <&misc_clk_2>,<&misc_clk_0>,<&misc_clk_1>,<&misc_clk_1>,<&misc_clk_1>, <&misc_clk_1>; + reg = <0x0 0xa0040000 0x0 0x40000>; + interrupt-parent = <&axi_intc>; + interrupts = <1 0>; + xlnx,sdfec-code = "ldpc"; + xlnx,sdfec-din-words = <0>; + xlnx,sdfec-din-width = <2>; + xlnx,sdfec-dout-words = <0>; + xlnx,sdfec-dout-width = <1>; + }; diff --git a/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml b/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml new file mode 100644 index 000000000000..d2d4308596b8 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml @@ -0,0 +1,104 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/allwinner,sun4i-a10-mmc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 MMC Controller Device Tree Bindings + +allOf: + - $ref: "mmc-controller.yaml" + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + "#address-cells": true + "#size-cells": true + + compatible: + oneOf: + - const: allwinner,sun4i-a10-mmc + - const: allwinner,sun5i-a13-mmc + - const: allwinner,sun7i-a20-mmc + - const: allwinner,sun8i-a83t-emmc + - const: allwinner,sun9i-a80-mmc + - const: allwinner,sun50i-a64-emmc + - const: allwinner,sun50i-a64-mmc + - items: + - const: allwinner,sun8i-a83t-mmc + - const: allwinner,sun7i-a20-mmc + - items: + - const: allwinner,sun8i-r40-emmc + - const: allwinner,sun50i-a64-emmc + - items: + - const: allwinner,sun8i-r40-mmc + - const: allwinner,sun50i-a64-mmc + - items: + - const: allwinner,sun50i-h5-emmc + - const: allwinner,sun50i-a64-emmc + - items: + - const: allwinner,sun50i-h5-mmc + - const: allwinner,sun50i-a64-mmc + - items: + - const: allwinner,sun50i-h6-emmc + - const: allwinner,sun50i-a64-emmc + - items: + - const: allwinner,sun50i-h6-mmc + - const: allwinner,sun50i-a64-mmc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 2 + maxItems: 4 + items: + - description: Bus Clock + - description: Module Clock + - description: Output Clock + - description: Sample Clock + + clock-names: + minItems: 2 + maxItems: 4 + items: + - const: ahb + - const: mmc + - const: output + - const: sample + + resets: + maxItems: 1 + + reset-names: + const: ahb + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +examples: + - | + mmc0: mmc@1c0f000 { + compatible = "allwinner,sun5i-a13-mmc"; + reg = <0x01c0f000 0x1000>; + clocks = <&ahb_gates 8>, <&mmc0_clk>; + clock-names = "ahb", "mmc"; + interrupts = <32>; + bus-width = <4>; + cd-gpios = <&pio 7 1 0>; + }; + +# FIXME: We should set it, but it would report all the generic +# properties as additional properties. +# additionalProperties: false + +... diff --git a/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt index 13e70409e8ac..ccc5358db131 100644 --- a/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt +++ b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt @@ -22,6 +22,10 @@ Required properties: clock rate requested by the MMC core. - resets : phandle of the internal reset line +Optional properties: +- amlogic,dram-access-quirk: set when controller's internal DMA engine cannot access the + DRAM memory, like on the G12A dedicated SDIO controller. + Example: sd_emmc_a: mmc@70000 { diff --git a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt index 1edbb049cccb..7ca0aa7ccc0b 100644 --- a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt @@ -17,6 +17,8 @@ Required Properties: For this device it is strongly suggested to include arasan,soc-ctl-syscon. - "ti,am654-sdhci-5.1", "arasan,sdhci-5.1": TI AM654 MMC PHY Note: This binding has been deprecated and moved to [5]. + - "intel,lgm-sdhci-5.1-emmc", "arasan,sdhci-5.1": Intel LGM eMMC PHY + For this device it is strongly suggested to include arasan,soc-ctl-syscon. [5] Documentation/devicetree/bindings/mmc/sdhci-am654.txt @@ -80,3 +82,18 @@ Example: phy-names = "phy_arasan"; #clock-cells = <0>; }; + + emmc: sdhci@ec700000 { + compatible = "intel,lgm-sdhci-5.1-emmc", "arasan,sdhci-5.1"; + reg = <0xec700000 0x300>; + interrupt-parent = <&ioapic1>; + interrupts = <44 1>; + clocks = <&cgu0 LGM_CLK_EMMC5>, <&cgu0 LGM_CLK_NGI>, + <&cgu0 LGM_GCLK_EMMC>; + clock-names = "clk_xin", "clk_ahb", "gate"; + clock-output-names = "emmc_cardclock"; + #clock-cells = <0>; + phys = <&emmc_phy>; + phy-names = "phy_arasan"; + arasan,soc-ctl-syscon = <&sysconf>; + }; diff --git a/Documentation/devicetree/bindings/mmc/aspeed,sdhci.yaml b/Documentation/devicetree/bindings/mmc/aspeed,sdhci.yaml new file mode 100644 index 000000000000..200de9396036 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/aspeed,sdhci.yaml @@ -0,0 +1,106 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# Copyright 2019 IBM Corp. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ASPEED SD/SDIO/MMC Controller + +maintainers: + - Andrew Jeffery <andrew@aj.id.au> + - Ryan Chen <ryanchen.aspeed@gmail.com> + +description: |+ + The ASPEED SD/SDIO/eMMC controller exposes two slots implementing the SDIO + Host Specification v2.00, with 1 or 4 bit data buses, or an 8 bit data bus if + only a single slot is enabled. + + The two slots are supported by a common configuration area. As the SDHCIs for + the slots are dependent on the common configuration area, they are described + as child nodes. + +properties: + compatible: + enum: + - aspeed,ast2400-sd-controller + - aspeed,ast2500-sd-controller + - aspeed,ast2600-sd-controller + reg: + maxItems: 1 + description: Common configuration registers + "#address-cells": + const: 1 + "#size-cells": + const: 1 + ranges: true + clocks: + maxItems: 1 + description: The SD/SDIO controller clock gate + +patternProperties: + "^sdhci@[0-9a-f]+$": + type: object + allOf: + - $ref: mmc-controller.yaml + properties: + compatible: + enum: + - aspeed,ast2400-sdhci + - aspeed,ast2500-sdhci + - aspeed,ast2600-sdhci + reg: + maxItems: 1 + description: The SDHCI registers + clocks: + maxItems: 1 + description: The SD bus clock + interrupts: + maxItems: 1 + description: The SD interrupt shared between both slots + sdhci,auto-cmd12: + type: boolean + description: Specifies that controller should use auto CMD12 + required: + - compatible + - reg + - clocks + - interrupts + +additionalProperties: false + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + - ranges + - clocks + +examples: + - | + #include <dt-bindings/clock/aspeed-clock.h> + sdc@1e740000 { + compatible = "aspeed,ast2500-sd-controller"; + reg = <0x1e740000 0x100>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x1e740000 0x20000>; + clocks = <&syscon ASPEED_CLK_GATE_SDCLK>; + + sdhci0: sdhci@100 { + compatible = "aspeed,ast2500-sdhci"; + reg = <0x100 0x100>; + interrupts = <26>; + sdhci,auto-cmd12; + clocks = <&syscon ASPEED_CLK_SDIO>; + }; + + sdhci1: sdhci@200 { + compatible = "aspeed,ast2500-sdhci"; + reg = <0x200 0x100>; + interrupts = <26>; + sdhci,auto-cmd12; + clocks = <&syscon ASPEED_CLK_SDIO>; + }; + }; diff --git a/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt b/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt index fa90d253dc7e..09d87cc1182a 100644 --- a/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt +++ b/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt @@ -6,10 +6,12 @@ by mmc.txt and the properties that represent the IPROC SDHCI controller. Required properties: - compatible : Should be one of the following "brcm,bcm2835-sdhci" + "brcm,bcm2711-emmc2" "brcm,sdhci-iproc-cygnus" "brcm,sdhci-iproc" -Use brcm2835-sdhci for Rasperry PI. +Use brcm2835-sdhci for the eMMC controller on the BCM2835 (Raspberry Pi) and +bcm2711-emmc2 for the additional eMMC2 controller on BCM2711. Use sdhci-iproc-cygnus for Broadcom SDHCI Controllers restricted to 32bit host accesses to SDHCI registers. diff --git a/Documentation/devicetree/bindings/mmc/mmc-controller.yaml b/Documentation/devicetree/bindings/mmc/mmc-controller.yaml new file mode 100644 index 000000000000..080754e0ef35 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/mmc-controller.yaml @@ -0,0 +1,374 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/mmc-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MMC Controller Generic Binding + +maintainers: + - Ulf Hansson <ulf.hansson@linaro.org> + +description: | + These properties are common to multiple MMC host controllers. Any host + that requires the respective functionality should implement them using + these definitions. + +properties: + $nodename: + pattern: "^mmc(@.*)?$" + + "#address-cells": + const: 1 + description: | + The cell is the slot ID if a function subnode is used. + + "#size-cells": + const: 0 + + # Card Detection. + # If none of these properties are supplied, the host native card + # detect will be used. Only one of them should be provided. + + broken-cd: + $ref: /schemas/types.yaml#/definitions/flag + description: + There is no card detection available; polling must be used. + + cd-gpios: + description: + The card detection will be done using the GPIO provided. + + non-removable: + $ref: /schemas/types.yaml#/definitions/flag + description: + Non-removable slot (like eMMC); assume always present. + + # *NOTE* on CD and WP polarity. To use common for all SD/MMC host + # controllers line polarity properties, we have to fix the meaning + # of the "normal" and "inverted" line levels. We choose to follow + # the SDHCI standard, which specifies both those lines as "active + # low." Therefore, using the "cd-inverted" property means, that the + # CD line is active high, i.e. it is high, when a card is + # inserted. Similar logic applies to the "wp-inverted" property. + # + # CD and WP lines can be implemented on the hardware in one of two + # ways: as GPIOs, specified in cd-gpios and wp-gpios properties, or + # as dedicated pins. Polarity of dedicated pins can be specified, + # using *-inverted properties. GPIO polarity can also be specified + # using the GPIO_ACTIVE_LOW flag. This creates an ambiguity in the + # latter case. We choose to use the XOR logic for GPIO CD and WP + # lines. This means, the two properties are "superimposed," for + # example leaving the GPIO_ACTIVE_LOW flag clear and specifying the + # respective *-inverted property property results in a + # double-inversion and actually means the "normal" line polarity is + # in effect. + wp-inverted: + $ref: /schemas/types.yaml#/definitions/flag + description: + The Write Protect line polarity is inverted. + + cd-inverted: + $ref: /schemas/types.yaml#/definitions/flag + description: + The CD line polarity is inverted. + + # Other properties + + bus-width: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [1, 4, 8] + default: 1 + description: + Number of data lines. + + max-frequency: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - minimum: 400000 + - maximum: 200000000 + description: + Maximum operating frequency of the bus. + + disable-wp: + $ref: /schemas/types.yaml#/definitions/flag + description: + When set, no physical write-protect line is present. This + property should only be specified when the controller has a + dedicated write-protect detection logic. If a GPIO is always + used for the write-protect detection. If a GPIO is always used + for the write-protect detection logic, it is sufficient to not + specify the wp-gpios property in the absence of a write-protect + line. + + wp-gpios: + description: + GPIO to use for the write-protect detection. + + cd-debounce-delay-ms: + description: + Set delay time before detecting card after card insert + interrupt. + + no-1-8-v: + $ref: /schemas/types.yaml#/definitions/flag + description: + When specified, denotes that 1.8V card voltage is not supported + on this system, even if the controller claims it. + + cap-sd-highspeed: + $ref: /schemas/types.yaml#/definitions/flag + description: + SD high-speed timing is supported. + + cap-mmc-highspeed: + $ref: /schemas/types.yaml#/definitions/flag + description: + MMC high-speed timing is supported. + + sd-uhs-sdr12: + $ref: /schemas/types.yaml#/definitions/flag + description: + SD UHS SDR12 speed is supported. + + sd-uhs-sdr25: + $ref: /schemas/types.yaml#/definitions/flag + description: + SD UHS SDR25 speed is supported. + + sd-uhs-sdr50: + $ref: /schemas/types.yaml#/definitions/flag + description: + SD UHS SDR50 speed is supported. + + sd-uhs-sdr104: + $ref: /schemas/types.yaml#/definitions/flag + description: + SD UHS SDR104 speed is supported. + + sd-uhs-ddr50: + $ref: /schemas/types.yaml#/definitions/flag + description: + SD UHS DDR50 speed is supported. + + cap-power-off-card: + $ref: /schemas/types.yaml#/definitions/flag + description: + Powering off the card is safe. + + cap-mmc-hw-reset: + $ref: /schemas/types.yaml#/definitions/flag + description: + eMMC hardware reset is supported + + cap-sdio-irq: + $ref: /schemas/types.yaml#/definitions/flag + description: + enable SDIO IRQ signalling on this interface + + full-pwr-cycle: + $ref: /schemas/types.yaml#/definitions/flag + description: + Full power cycle of the card is supported. + + mmc-ddr-1_2v: + $ref: /schemas/types.yaml#/definitions/flag + description: + eMMC high-speed DDR mode (1.2V I/O) is supported. + + mmc-ddr-1_8v: + $ref: /schemas/types.yaml#/definitions/flag + description: + eMMC high-speed DDR mode (1.8V I/O) is supported. + + mmc-ddr-3_3v: + $ref: /schemas/types.yaml#/definitions/flag + description: + eMMC high-speed DDR mode (3.3V I/O) is supported. + + mmc-hs200-1_2v: + $ref: /schemas/types.yaml#/definitions/flag + description: + eMMC HS200 mode (1.2V I/O) is supported. + + mmc-hs200-1_8v: + $ref: /schemas/types.yaml#/definitions/flag + description: + eMMC HS200 mode (1.8V I/O) is supported. + + mmc-hs400-1_2v: + $ref: /schemas/types.yaml#/definitions/flag + description: + eMMC HS400 mode (1.2V I/O) is supported. + + mmc-hs400-1_8v: + $ref: /schemas/types.yaml#/definitions/flag + description: + eMMC HS400 mode (1.8V I/O) is supported. + + mmc-hs400-enhanced-strobe: + $ref: /schemas/types.yaml#/definitions/flag + description: + eMMC HS400 enhanced strobe mode is supported + + dsr: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - minimum: 0 + - maximum: 0xffff + description: + Value the card Driver Stage Register (DSR) should be programmed + with. + + no-sdio: + $ref: /schemas/types.yaml#/definitions/flag + description: + Controller is limited to send SDIO commands during + initialization. + + no-sd: + $ref: /schemas/types.yaml#/definitions/flag + description: + Controller is limited to send SD commands during initialization. + + no-mmc: + $ref: /schemas/types.yaml#/definitions/flag + description: + Controller is limited to send MMC commands during + initialization. + + fixed-emmc-driver-type: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - minimum: 0 + - maximum: 4 + description: + For non-removable eMMC, enforce this driver type. The value is + the driver type as specified in the eMMC specification (table + 206 in spec version 5.1) + + post-power-on-delay-ms: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - default: 10 + description: + It was invented for MMC pwrseq-simple which could be referred to + mmc-pwrseq-simple.txt. But now it\'s reused as a tunable delay + waiting for I/O signalling and card power supply to be stable, + regardless of whether pwrseq-simple is used. Default to 10ms if + no available. + + supports-cqe: + $ref: /schemas/types.yaml#/definitions/flag + description: + The presence of this property indicates that the corresponding + MMC host controller supports HW command queue feature. + + disable-cqe-dcmd: + $ref: /schemas/types.yaml#/definitions/flag + description: + The presence of this property indicates that the MMC + controller\'s command queue engine (CQE) does not support direct + commands (DCMDs). + + keep-power-in-suspend: + $ref: /schemas/types.yaml#/definitions/flag + description: + SDIO only. Preserves card power during a suspend/resume cycle. + + # Deprecated: enable-sdio-wakeup + wakeup-source: + $ref: /schemas/types.yaml#/definitions/flag + description: + SDIO only. Enables wake up of host system on SDIO IRQ assertion. + + vmmc-supply: + description: + Supply for the card power + + vqmmc-supply: + description: + Supply for the bus IO line power + + mmc-pwrseq: + $ref: /schemas/types.yaml#/definitions/phandle + description: + System-on-Chip designs may specify a specific MMC power + sequence. To successfully detect an (e)MMC/SD/SDIO card, that + power sequence must be maintained while initializing the card. + +patternProperties: + "^.*@[0-9]+$": + type: object + description: | + On embedded systems the cards connected to a host may need + additional properties. These can be specified in subnodes to the + host controller node. The subnodes are identified by the + standard \'reg\' property. Which information exactly can be + specified depends on the bindings for the SDIO function driver + for the subnode, as specified by the compatible string. + + properties: + compatible: + description: | + Name of SDIO function following generic names recommended + practice + + reg: + items: + - minimum: 0 + maximum: 7 + description: + Must contain the SDIO function number of the function this + subnode describes. A value of 0 denotes the memory SD + function, values from 1 to 7 denote the SDIO functions. + + broken-hpi: + $ref: /schemas/types.yaml#/definitions/flag + description: + Use this to indicate that the mmc-card has a broken hpi + implementation, and that hpi should not be used. + + required: + - reg + +dependencies: + cd-debounce-delay-ms: [ cd-gpios ] + fixed-emmc-driver-type: [ non-removable ] + +examples: + - | + sdhci@ab000000 { + compatible = "sdhci"; + reg = <0xab000000 0x200>; + interrupts = <23>; + bus-width = <4>; + cd-gpios = <&gpio 69 0>; + cd-inverted; + wp-gpios = <&gpio 70 0>; + max-frequency = <50000000>; + keep-power-in-suspend; + wakeup-source; + mmc-pwrseq = <&sdhci0_pwrseq>; + }; + + - | + mmc3: mmc@1c12000 { + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins_a>; + vmmc-supply = <®_vmmc3>; + bus-width = <4>; + non-removable; + mmc-pwrseq = <&sdhci0_pwrseq>; + + brcmf: bcrmf@1 { + reg = <1>; + compatible = "brcm,bcm43xx-fmac"; + interrupt-parent = <&pio>; + interrupts = <10 8>; + interrupt-names = "host-wake"; + }; + }; diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index c269dbe384fe..bf9d7d3febf1 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -1,177 +1 @@ -These properties are common to multiple MMC host controllers. Any host -that requires the respective functionality should implement them using -these definitions. - -Interpreted by the OF core: -- reg: Registers location and length. -- interrupts: Interrupts used by the MMC controller. - -Card detection: -If no property below is supplied, host native card detect is used. -Only one of the properties in this section should be supplied: - - broken-cd: There is no card detection available; polling must be used. - - cd-gpios: Specify GPIOs for card detection, see gpio binding - - non-removable: non-removable slot (like eMMC); assume always present. - -Optional properties: -- bus-width: Number of data lines, can be <1>, <4>, or <8>. The default - will be <1> if the property is absent. -- wp-gpios: Specify GPIOs for write protection, see gpio binding -- cd-inverted: when present, polarity on the CD line is inverted. See the note - below for the case, when a GPIO is used for the CD line -- cd-debounce-delay-ms: Set delay time before detecting card after card insert interrupt. - It's only valid when cd-gpios is present. -- wp-inverted: when present, polarity on the WP line is inverted. See the note - below for the case, when a GPIO is used for the WP line -- disable-wp: When set no physical WP line is present. This property should - only be specified when the controller has a dedicated write-protect - detection logic. If a GPIO is always used for the write-protect detection - logic it is sufficient to not specify wp-gpios property in the absence of a WP - line. -- max-frequency: maximum operating clock frequency -- no-1-8-v: when present, denotes that 1.8v card voltage is not supported on - this system, even if the controller claims it is. -- cap-sd-highspeed: SD high-speed timing is supported -- cap-mmc-highspeed: MMC high-speed timing is supported -- sd-uhs-sdr12: SD UHS SDR12 speed is supported -- sd-uhs-sdr25: SD UHS SDR25 speed is supported -- sd-uhs-sdr50: SD UHS SDR50 speed is supported -- sd-uhs-sdr104: SD UHS SDR104 speed is supported -- sd-uhs-ddr50: SD UHS DDR50 speed is supported -- cap-power-off-card: powering off the card is safe -- cap-mmc-hw-reset: eMMC hardware reset is supported -- cap-sdio-irq: enable SDIO IRQ signalling on this interface -- full-pwr-cycle: full power cycle of the card is supported -- mmc-ddr-3_3v: eMMC high-speed DDR mode(3.3V I/O) is supported -- mmc-ddr-1_8v: eMMC high-speed DDR mode(1.8V I/O) is supported -- mmc-ddr-1_2v: eMMC high-speed DDR mode(1.2V I/O) is supported -- mmc-hs200-1_8v: eMMC HS200 mode(1.8V I/O) is supported -- mmc-hs200-1_2v: eMMC HS200 mode(1.2V I/O) is supported -- mmc-hs400-1_8v: eMMC HS400 mode(1.8V I/O) is supported -- mmc-hs400-1_2v: eMMC HS400 mode(1.2V I/O) is supported -- mmc-hs400-enhanced-strobe: eMMC HS400 enhanced strobe mode is supported -- dsr: Value the card's (optional) Driver Stage Register (DSR) should be - programmed with. Valid range: [0 .. 0xffff]. -- no-sdio: controller is limited to send sdio cmd during initialization -- no-sd: controller is limited to send sd cmd during initialization -- no-mmc: controller is limited to send mmc cmd during initialization -- fixed-emmc-driver-type: for non-removable eMMC, enforce this driver type. - The value <n> is the driver type as specified in the eMMC specification - (table 206 in spec version 5.1). -- post-power-on-delay-ms : It was invented for MMC pwrseq-simple which could - be referred to mmc-pwrseq-simple.txt. But now it's reused as a tunable delay - waiting for I/O signalling and card power supply to be stable, regardless of - whether pwrseq-simple is used. Default to 10ms if no available. -- supports-cqe : The presence of this property indicates that the corresponding - MMC host controller supports HW command queue feature. -- disable-cqe-dcmd: This property indicates that the MMC controller's command - queue engine (CQE) does not support direct commands (DCMDs). - -*NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line -polarity properties, we have to fix the meaning of the "normal" and "inverted" -line levels. We choose to follow the SDHCI standard, which specifies both those -lines as "active low." Therefore, using the "cd-inverted" property means, that -the CD line is active high, i.e. it is high, when a card is inserted. Similar -logic applies to the "wp-inverted" property. - -CD and WP lines can be implemented on the hardware in one of two ways: as GPIOs, -specified in cd-gpios and wp-gpios properties, or as dedicated pins. Polarity of -dedicated pins can be specified, using *-inverted properties. GPIO polarity can -also be specified using the GPIO_ACTIVE_LOW flag. This creates an ambiguity -in the latter case. We choose to use the XOR logic for GPIO CD and WP lines. -This means, the two properties are "superimposed," for example leaving the -GPIO_ACTIVE_LOW flag clear and specifying the respective *-inverted property -property results in a double-inversion and actually means the "normal" line -polarity is in effect. - -Optional SDIO properties: -- keep-power-in-suspend: Preserves card power during a suspend/resume cycle -- wakeup-source: Enables wake up of host system on SDIO IRQ assertion - (Legacy property supported: "enable-sdio-wakeup") - -MMC power ---------- - -Controllers may implement power control from both the connected cards and -the IO signaling (for example to change to high-speed 1.8V signalling). If -the system supports this, then the following two properties should point -to valid regulator nodes: - -- vqmmc-supply: supply node for IO line power -- vmmc-supply: supply node for card's power - - -MMC power sequences: --------------------- - -System on chip designs may specify a specific MMC power sequence. To -successfully detect an (e)MMC/SD/SDIO card, that power sequence must be -maintained while initializing the card. - -Optional property: -- mmc-pwrseq: phandle to the MMC power sequence node. See "mmc-pwrseq-*" - for documentation of MMC power sequence bindings. - - -Use of Function subnodes ------------------------- - -On embedded systems the cards connected to a host may need additional -properties. These can be specified in subnodes to the host controller node. -The subnodes are identified by the standard 'reg' property. -Which information exactly can be specified depends on the bindings for the -SDIO function driver for the subnode, as specified by the compatible string. - -Required host node properties when using function subnodes: -- #address-cells: should be one. The cell is the slot id. -- #size-cells: should be zero. - -Required function subnode properties: -- reg: Must contain the SDIO function number of the function this subnode - describes. A value of 0 denotes the memory SD function, values from - 1 to 7 denote the SDIO functions. - -Optional function subnode properties: -- compatible: name of SDIO function following generic names recommended practice - - -Examples --------- - -Basic example: - -sdhci@ab000000 { - compatible = "sdhci"; - reg = <0xab000000 0x200>; - interrupts = <23>; - bus-width = <4>; - cd-gpios = <&gpio 69 0>; - cd-inverted; - wp-gpios = <&gpio 70 0>; - max-frequency = <50000000>; - keep-power-in-suspend; - wakeup-source; - mmc-pwrseq = <&sdhci0_pwrseq> -} - -Example with sdio function subnode: - -mmc3: mmc@1c12000 { - #address-cells = <1>; - #size-cells = <0>; - - pinctrl-names = "default"; - pinctrl-0 = <&mmc3_pins_a>; - vmmc-supply = <®_vmmc3>; - bus-width = <4>; - non-removable; - mmc-pwrseq = <&sdhci0_pwrseq> - - brcmf: bcrmf@1 { - reg = <1>; - compatible = "brcm,bcm43xx-fmac"; - interrupt-parent = <&pio>; - interrupts = <10 8>; /* PH10 / EINT10 */ - interrupt-names = "host-wake"; - }; -}; +This file has moved to mmc-controller.yaml. diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/renesas,sdhi.txt index 2b4f17ca9087..dd08d038a65c 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/renesas,sdhi.txt @@ -1,13 +1,4 @@ -* Toshiba Mobile IO SD/MMC controller - -The tmio-mmc driver doesn't probe its devices actively, instead its binding to -devices is managed by either MFD drivers or by the sh_mobile_sdhi platform -driver. Those drivers supply the tmio-mmc driver with platform data, that either -describe hardware capabilities, known to them, or are obtained by them from -their own platform data or from their DT information. In the latter case all -compulsory and any optional properties, common to all SD/MMC drivers, as -described in mmc.txt, can be used. Additionally the following tmio_mmc-specific -optional bindings can be used. +* Renesas SDHI SD/MMC controller Required properties: - compatible: should contain one or more of the following: diff --git a/Documentation/devicetree/bindings/mmc/sdhci-am654.txt b/Documentation/devicetree/bindings/mmc/sdhci-am654.txt index 15dbbbace27e..50e87df47971 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-am654.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-am654.txt @@ -8,7 +8,10 @@ Only deviations are documented here. [3] Documentation/devicetree/bindings/interrupt-controller/interrupts.txt Required Properties: - - compatible: should be "ti,am654-sdhci-5.1" + - compatible: should be one of: + "ti,am654-sdhci-5.1": SDHCI on AM654 device. + "ti,j721e-sdhci-8bit": 8 bit SDHCI on J721E device. + "ti,j721e-sdhci-4bit": 4 bit SDHCI on J721E device. - reg: Must be two entries. - The first should be the sdhci register space - The second should the subsystem/phy register space @@ -16,9 +19,13 @@ Required Properties: - clock-names: Tuple including "clk_xin" and "clk_ahb" - interrupts: Interrupt specifiers - ti,otap-del-sel: Output Tap Delay select + +Optional Properties (Required for ti,am654-sdhci-5.1 and ti,j721e-sdhci-8bit): - ti,trm-icp: DLL trim select - ti,driver-strength-ohm: driver strength in ohms. Valid values are 33, 40, 50, 66 and 100 ohms. +Optional Properties: + - ti,strobe-sel: strobe select delay for HS400 speed mode. Default value: 0x0. Example: diff --git a/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt b/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt index 45c9978aad7b..eb7eb1b529f0 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt @@ -14,10 +14,31 @@ Required properties: - clock-names: Should contain the following: "sdio" - SDIO source clock (required) "enable" - gate clock which used for enabling/disabling the device (required) + "2x_enable" - gate clock controlling the device for some special platforms (optional) Optional properties: - assigned-clocks: the same with "sdio" clock - assigned-clock-parents: the default parent of "sdio" clock +- pinctrl-names: should be "default", "state_uhs" +- pinctrl-0: should contain default/high speed pin control +- pinctrl-1: should contain uhs mode pin control + +PHY DLL delays are used to delay the data valid window, and align the window +to sampling clock. PHY DLL delays can be configured by following properties, +and each property contains 4 cells which are used to configure the clock data +write line delay value, clock read command line delay value, clock read data +positive edge delay value and clock read data negative edge delay value. +Each cell's delay value unit is cycle of the PHY clock. + +- sprd,phy-delay-legacy: Delay value for legacy timing. +- sprd,phy-delay-sd-highspeed: Delay value for SD high-speed timing. +- sprd,phy-delay-sd-uhs-sdr50: Delay value for SD UHS SDR50 timing. +- sprd,phy-delay-sd-uhs-sdr104: Delay value for SD UHS SDR50 timing. +- sprd,phy-delay-mmc-highspeed: Delay value for MMC high-speed timing. +- sprd,phy-delay-mmc-ddr52: Delay value for MMC DDR52 timing. +- sprd,phy-delay-mmc-hs200: Delay value for MMC HS200 timing. +- sprd,phy-delay-mmc-hs400: Delay value for MMC HS400 timing. +- sprd,phy-delay-mmc-hs400es: Delay value for MMC HS400 enhanced strobe timing. Examples: @@ -32,6 +53,11 @@ sdio0: sdio@20600000 { assigned-clocks = <&ap_clk CLK_EMMC_2X>; assigned-clock-parents = <&rpll CLK_RPLL_390M>; + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&sd0_pins_default>; + pinctrl-1 = <&sd0_pins_uhs>; + + sprd,phy-delay-sd-uhs-sdr104 = <0x3f 0x7f 0x2e 0x2e>; bus-width = <8>; non-removable; no-sdio; diff --git a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt deleted file mode 100644 index e9cb3ec5e502..000000000000 --- a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt +++ /dev/null @@ -1,52 +0,0 @@ -* Allwinner sunxi MMC controller - -The highspeed MMC host controller on Allwinner SoCs provides an interface -for MMC, SD and SDIO types of memory cards. - -Supported maximum speeds are the ones of the eMMC standard 4.5 as well -as the speed of SD standard 3.0. -Absolute maximum transfer rate is 200MB/s - -Required properties: - - compatible : should be one of: - * "allwinner,sun4i-a10-mmc" - * "allwinner,sun5i-a13-mmc" - * "allwinner,sun7i-a20-mmc" - * "allwinner,sun8i-a83t-emmc" - * "allwinner,sun9i-a80-mmc" - * "allwinner,sun50i-a64-emmc" - * "allwinner,sun50i-a64-mmc" - * "allwinner,sun50i-h6-emmc", "allwinner.sun50i-a64-emmc" - * "allwinner,sun50i-h6-mmc", "allwinner.sun50i-a64-mmc" - - reg : mmc controller base registers - - clocks : a list with 4 phandle + clock specifier pairs - - clock-names : must contain "ahb", "mmc", "output" and "sample" - - interrupts : mmc controller interrupt - -Optional properties: - - resets : phandle + reset specifier pair - - reset-names : must contain "ahb" - - for cd, bus-width and additional generic mmc parameters - please refer to mmc.txt within this directory - -Examples: - - Within .dtsi: - mmc0: mmc@1c0f000 { - compatible = "allwinner,sun5i-a13-mmc"; - reg = <0x01c0f000 0x1000>; - clocks = <&ahb_gates 8>, <&mmc0_clk>, <&mmc0_output_clk>, <&mmc0_sample_clk>; - clock-names = "ahb", "mod", "output", "sample"; - interrupts = <0 32 4>; - status = "disabled"; - }; - - - Within dts: - mmc0: mmc@1c0f000 { - pinctrl-names = "default", "default"; - pinctrl-0 = <&mmc0_pins_a>; - pinctrl-1 = <&mmc0_cd_pin_reference_design>; - bus-width = <4>; - cd-gpios = <&pio 7 1 0>; /* PH1 */ - cd-inverted; - status = "okay"; - }; diff --git a/Documentation/devicetree/bindings/mtd/allwinner,sun4i-a10-nand.yaml b/Documentation/devicetree/bindings/mtd/allwinner,sun4i-a10-nand.yaml index fbd4da3684fc..b5b3cf5b1ac2 100644 --- a/Documentation/devicetree/bindings/mtd/allwinner,sun4i-a10-nand.yaml +++ b/Documentation/devicetree/bindings/mtd/allwinner,sun4i-a10-nand.yaml @@ -55,9 +55,9 @@ patternProperties: "^pinctrl-[0-9]+$": true "^nand@[a-f0-9]+$": + type: object properties: reg: - maxItems: 1 minimum: 0 maximum: 7 diff --git a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt index 0b7c3738b66c..82156dc8f304 100644 --- a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt +++ b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt @@ -28,6 +28,7 @@ Required properties: brcm,brcmnand-v7.0 brcm,brcmnand-v7.1 brcm,brcmnand-v7.2 + brcm,brcmnand-v7.3 brcm,brcmnand - reg : the register start and length for NAND register region. (optional) Flash DMA register range (if present) @@ -101,10 +102,10 @@ Required properties: number (e.g., 0, 1, 2, etc.) - #address-cells : see partition.txt - #size-cells : see partition.txt -- nand-ecc-strength : see nand-controller.yaml -- nand-ecc-step-size : must be 512 or 1024. See nand-controller.yaml Optional properties: +- nand-ecc-strength : see nand-controller.yaml +- nand-ecc-step-size : must be 512 or 1024. See nand-controller.yaml - nand-on-flash-bbt : boolean, to enable the on-flash BBT for this chip-select. See nand-controller.yaml - brcm,nand-oob-sector-size : integer, to denote the spare area sector size diff --git a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt index 4345c3a6f530..945be7d5b236 100644 --- a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt +++ b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt @@ -35,6 +35,9 @@ custom properties: (qspi_n_ss_out). - cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low and first bit transfer. +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include either "qspi" and/or "qspi-ocp". Example: @@ -50,6 +53,8 @@ Example: cdns,fifo-depth = <128>; cdns,fifo-width = <4>; cdns,trigger-address = <0x00000000>; + resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>; + reset-names = "qspi", "qspi-ocp"; flash0: n25q00@0 { ... diff --git a/Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt b/Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt new file mode 100644 index 000000000000..ad42f4db32f1 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/cypress,hyperflash.txt @@ -0,0 +1,13 @@ +Bindings for HyperFlash NOR flash chips compliant with Cypress HyperBus +specification and supports Cypress CFI specification 1.5 command set. + +Required properties: +- compatible : "cypress,hyperflash", "cfi-flash" for HyperFlash NOR chips +- reg : Address of flash's memory map + +Example: + + flash@0 { + compatible = "cypress,hyperflash", "cfi-flash"; + reg = <0x0 0x4000000>; + }; diff --git a/Documentation/devicetree/bindings/mtd/mxic-nand.txt b/Documentation/devicetree/bindings/mtd/mxic-nand.txt new file mode 100644 index 000000000000..46c55295a3e6 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/mxic-nand.txt @@ -0,0 +1,36 @@ +Macronix Raw NAND Controller Device Tree Bindings +------------------------------------------------- + +Required properties: +- compatible: should be "mxic,multi-itfc-v009-nand-controller" +- reg: should contain 1 entry for the registers +- #address-cells: should be set to 1 +- #size-cells: should be set to 0 +- interrupts: interrupt line connected to this raw NAND controller +- clock-names: should contain "ps", "send" and "send_dly" +- clocks: should contain 3 phandles for the "ps", "send" and + "send_dly" clocks + +Children nodes: +- children nodes represent the available NAND chips. + +See Documentation/devicetree/bindings/mtd/nand-controller.yaml +for more details on generic bindings. + +Example: + + nand: nand-controller@43c30000 { + compatible = "mxic,multi-itfc-v009-nand-controller"; + reg = <0x43c30000 0x10000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 0x1d IRQ_TYPE_EDGE_RISING>; + clocks = <&clkwizard 0>, <&clkwizard 1>, <&clkc 15>; + clock-names = "send", "send_dly", "ps"; + + nand@0 { + reg = <0>; + nand-ecc-mode = "soft"; + nand-ecc-algo = "bch"; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/nand-controller.yaml b/Documentation/devicetree/bindings/mtd/nand-controller.yaml index 199ba5ac2a06..d261b7096c69 100644 --- a/Documentation/devicetree/bindings/mtd/nand-controller.yaml +++ b/Documentation/devicetree/bindings/mtd/nand-controller.yaml @@ -40,6 +40,7 @@ properties: patternProperties: "^nand@[a-f0-9]$": + type: object properties: reg: description: diff --git a/Documentation/devicetree/bindings/mtd/stm32-quadspi.txt b/Documentation/devicetree/bindings/mtd/stm32-quadspi.txt deleted file mode 100644 index ddd18c135148..000000000000 --- a/Documentation/devicetree/bindings/mtd/stm32-quadspi.txt +++ /dev/null @@ -1,43 +0,0 @@ -* STMicroelectronics Quad Serial Peripheral Interface(QuadSPI) - -Required properties: -- compatible: should be "st,stm32f469-qspi" -- reg: the first contains the register location and length. - the second contains the memory mapping address and length -- reg-names: should contain the reg names "qspi" "qspi_mm" -- interrupts: should contain the interrupt for the device -- clocks: the phandle of the clock needed by the QSPI controller -- A pinctrl must be defined to set pins in mode of operation for QSPI transfer - -Optional properties: -- resets: must contain the phandle to the reset controller. - -A spi flash must be a child of the nor_flash node and could have some -properties. Also see jedec,spi-nor.txt. - -Required properties: -- reg: chip-Select number (QSPI controller may connect 2 nor flashes) -- spi-max-frequency: max frequency of spi bus - -Optional property: -- spi-rx-bus-width: see ../spi/spi-bus.txt for the description - -Example: - -qspi: spi@a0001000 { - compatible = "st,stm32f469-qspi"; - reg = <0xa0001000 0x1000>, <0x90000000 0x10000000>; - reg-names = "qspi", "qspi_mm"; - interrupts = <91>; - resets = <&rcc STM32F4_AHB3_RESET(QSPI)>; - clocks = <&rcc 0 STM32F4_AHB3_CLOCK(QSPI)>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_qspi0>; - - flash@0 { - reg = <0>; - spi-rx-bus-width = <4>; - spi-max-frequency = <108000000>; - ... - }; -}; diff --git a/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt b/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt new file mode 100644 index 000000000000..faa81c2e5da6 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.txt @@ -0,0 +1,51 @@ +Bindings for HyperBus Memory Controller (HBMC) on TI's K3 family of SoCs + +Required properties: +- compatible : "ti,am654-hbmc" for AM654 SoC +- reg : Two entries: + First entry pointed to the register space of HBMC controller + Second entry pointing to the memory map region dedicated for + MMIO access to attached flash devices +- ranges : Address translation from offset within CS to allocated MMIO + space in SoC + +Optional properties: +- mux-controls : phandle to the multiplexer that controls selection of + HBMC vs OSPI inside Flash SubSystem (FSS). Default is OSPI, + if property is absent. + See Documentation/devicetree/bindings/mux/reg-mux.txt + for mmio-mux binding details + +Example: + + system-controller@47000000 { + compatible = "syscon", "simple-mfd"; + reg = <0x0 0x47000000 0x0 0x100>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + hbmc_mux: multiplexer { + compatible = "mmio-mux"; + #mux-control-cells = <1>; + mux-reg-masks = <0x4 0x2>; /* 0: reg 0x4, bit 1 */ + }; + }; + + hbmc: hyperbus@47034000 { + compatible = "ti,am654-hbmc"; + reg = <0x0 0x47034000 0x0 0x100>, + <0x5 0x00000000 0x1 0x0000000>; + power-domains = <&k3_pds 55>; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0x0 0x0 0x5 0x00000000 0x4000000>, /* CS0 - 64MB */ + <0x1 0x0 0x5 0x04000000 0x4000000>; /* CS1 - 64MB */ + mux-controls = <&hbmc_mux 0>; + + /* Slave flash node */ + flash@0,0 { + compatible = "cypress,hyperflash", "cfi-flash"; + reg = <0x0 0x0 0x4000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/mux/mmio-mux.txt b/Documentation/devicetree/bindings/mux/mmio-mux.txt deleted file mode 100644 index a9bfb4d8b6ac..000000000000 --- a/Documentation/devicetree/bindings/mux/mmio-mux.txt +++ /dev/null @@ -1,60 +0,0 @@ -MMIO register bitfield-based multiplexer controller bindings - -Define register bitfields to be used to control multiplexers. The parent -device tree node must be a syscon node to provide register access. - -Required properties: -- compatible : "mmio-mux" -- #mux-control-cells : <1> -- mux-reg-masks : an array of register offset and pre-shifted bitfield mask - pairs, each describing a single mux control. -* Standard mux-controller bindings as decribed in mux-controller.txt - -Optional properties: -- idle-states : if present, the state the muxes will have when idle. The - special state MUX_IDLE_AS_IS is the default. - -The multiplexer state of each multiplexer is defined as the value of the -bitfield described by the corresponding register offset and bitfield mask pair -in the mux-reg-masks array, accessed through the parent syscon. - -Example: - - syscon { - compatible = "syscon"; - - mux: mux-controller { - compatible = "mmio-mux"; - #mux-control-cells = <1>; - - mux-reg-masks = <0x3 0x30>, /* 0: reg 0x3, bits 5:4 */ - <0x3 0x40>, /* 1: reg 0x3, bit 6 */ - idle-states = <MUX_IDLE_AS_IS>, <0>; - }; - }; - - video-mux { - compatible = "video-mux"; - mux-controls = <&mux 0>; - - ports { - /* inputs 0..3 */ - port@0 { - reg = <0>; - }; - port@1 { - reg = <1>; - }; - port@2 { - reg = <2>; - }; - port@3 { - reg = <3>; - }; - - /* output */ - port@4 { - reg = <4>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/mux/reg-mux.txt b/Documentation/devicetree/bindings/mux/reg-mux.txt new file mode 100644 index 000000000000..4afd7ba73d60 --- /dev/null +++ b/Documentation/devicetree/bindings/mux/reg-mux.txt @@ -0,0 +1,129 @@ +Generic register bitfield-based multiplexer controller bindings + +Define register bitfields to be used to control multiplexers. The parent +device tree node must be a device node to provide register r/w access. + +Required properties: +- compatible : should be one of + "reg-mux" : if parent device of mux controller is not syscon device + "mmio-mux" : if parent device of mux controller is syscon device +- #mux-control-cells : <1> +- mux-reg-masks : an array of register offset and pre-shifted bitfield mask + pairs, each describing a single mux control. +* Standard mux-controller bindings as decribed in mux-controller.txt + +Optional properties: +- idle-states : if present, the state the muxes will have when idle. The + special state MUX_IDLE_AS_IS is the default. + +The multiplexer state of each multiplexer is defined as the value of the +bitfield described by the corresponding register offset and bitfield mask +pair in the mux-reg-masks array. + +Example 1: +The parent device of mux controller is not a syscon device. + +&i2c0 { + fpga@66 { // fpga connected to i2c + compatible = "fsl,lx2160aqds-fpga", "fsl,fpga-qixis-i2c", + "simple-mfd"; + reg = <0x66>; + + mux: mux-controller { + compatible = "reg-mux"; + #mux-control-cells = <1>; + mux-reg-masks = <0x54 0xf8>, /* 0: reg 0x54, bits 7:3 */ + <0x54 0x07>; /* 1: reg 0x54, bits 2:0 */ + }; + }; +}; + +mdio-mux-1 { + compatible = "mdio-mux-multiplexer"; + mux-controls = <&mux 0>; + mdio-parent-bus = <&emdio1>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + mdio@8 { + reg = <0x8>; + #address-cells = <1>; + #size-cells = <0>; + }; + + .. + .. +}; + +mdio-mux-2 { + compatible = "mdio-mux-multiplexer"; + mux-controls = <&mux 1>; + mdio-parent-bus = <&emdio2>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + mdio@1 { + reg = <0x1>; + #address-cells = <1>; + #size-cells = <0>; + }; + + .. + .. +}; + +Example 2: +The parent device of mux controller is syscon device. + +syscon { + compatible = "syscon"; + + mux: mux-controller { + compatible = "mmio-mux"; + #mux-control-cells = <1>; + + mux-reg-masks = <0x3 0x30>, /* 0: reg 0x3, bits 5:4 */ + <0x3 0x40>, /* 1: reg 0x3, bit 6 */ + idle-states = <MUX_IDLE_AS_IS>, <0>; + }; +}; + +video-mux { + compatible = "video-mux"; + mux-controls = <&mux 0>; + #address-cells = <1>; + #size-cells = <0>; + + ports { + /* inputs 0..3 */ + port@0 { + reg = <0>; + }; + port@1 { + reg = <1>; + }; + port@2 { + reg = <2>; + }; + port@3 { + reg = <3>; + }; + + /* output */ + port@4 { + reg = <4>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/adi,adin.yaml b/Documentation/devicetree/bindings/net/adi,adin.yaml new file mode 100644 index 000000000000..69375cb28e92 --- /dev/null +++ b/Documentation/devicetree/bindings/net/adi,adin.yaml @@ -0,0 +1,73 @@ +# SPDX-License-Identifier: GPL-2.0+ +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/adi,adin.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices ADIN1200/ADIN1300 PHY + +maintainers: + - Alexandru Ardelean <alexandru.ardelean@analog.com> + +description: | + Bindings for Analog Devices Industrial Ethernet PHYs + +allOf: + - $ref: ethernet-phy.yaml# + +properties: + adi,rx-internal-delay-ps: + description: | + RGMII RX Clock Delay used only when PHY operates in RGMII mode with + internal delay (phy-mode is 'rgmii-id' or 'rgmii-rxid') in pico-seconds. + enum: [ 1600, 1800, 2000, 2200, 2400 ] + default: 2000 + + adi,tx-internal-delay-ps: + description: | + RGMII TX Clock Delay used only when PHY operates in RGMII mode with + internal delay (phy-mode is 'rgmii-id' or 'rgmii-txid') in pico-seconds. + enum: [ 1600, 1800, 2000, 2200, 2400 ] + default: 2000 + + adi,fifo-depth-bits: + description: | + When operating in RMII mode, this option configures the FIFO depth. + enum: [ 4, 8, 12, 16, 20, 24 ] + default: 8 + + adi,disable-energy-detect: + description: | + Disables Energy Detect Powerdown Mode (default disabled, i.e energy detect + is enabled if this property is unspecified) + type: boolean + +examples: + - | + ethernet { + #address-cells = <1>; + #size-cells = <0>; + + phy-mode = "rgmii-id"; + + ethernet-phy@0 { + reg = <0>; + + adi,rx-internal-delay-ps = <1800>; + adi,tx-internal-delay-ps = <2200>; + }; + }; + - | + ethernet { + #address-cells = <1>; + #size-cells = <0>; + + phy-mode = "rmii"; + + ethernet-phy@1 { + reg = <1>; + + adi,fifo-depth-bits = <16>; + adi,disable-energy-detect; + }; + }; diff --git a/Documentation/devicetree/bindings/net/allwinner,sun4i-a10-emac.yaml b/Documentation/devicetree/bindings/net/allwinner,sun4i-a10-emac.yaml new file mode 100644 index 000000000000..792196bf4abd --- /dev/null +++ b/Documentation/devicetree/bindings/net/allwinner,sun4i-a10-emac.yaml @@ -0,0 +1,56 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/allwinner,sun4i-a10-emac.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 EMAC Ethernet Controller Device Tree Bindings + +allOf: + - $ref: "ethernet-controller.yaml#" + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + compatible: + const: allwinner,sun4i-a10-emac + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + allwinner,sram: + description: Phandle to the device SRAM + $ref: /schemas/types.yaml#/definitions/phandle-array + +required: + - compatible + - reg + - interrupts + - clocks + - phy-handle + - allwinner,sram + +examples: + - | + emac: ethernet@1c0b000 { + compatible = "allwinner,sun4i-a10-emac"; + reg = <0x01c0b000 0x1000>; + interrupts = <55>; + clocks = <&ahb_gates 17>; + phy-handle = <&phy0>; + allwinner,sram = <&emac_sram 1>; + }; + +# FIXME: We should set it, but it would report all the generic +# properties as additional properties. +# additionalProperties: false + +... diff --git a/Documentation/devicetree/bindings/net/allwinner,sun4i-a10-mdio.yaml b/Documentation/devicetree/bindings/net/allwinner,sun4i-a10-mdio.yaml new file mode 100644 index 000000000000..df24d9d969f7 --- /dev/null +++ b/Documentation/devicetree/bindings/net/allwinner,sun4i-a10-mdio.yaml @@ -0,0 +1,70 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/allwinner,sun4i-a10-mdio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 MDIO Controller Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +allOf: + - $ref: "mdio.yaml#" + +# Select every compatible, including the deprecated ones. This way, we +# will be able to report a warning when we have that compatible, since +# we will validate the node thanks to the select, but won't report it +# as a valid value in the compatible property description +select: + properties: + compatible: + enum: + - allwinner,sun4i-a10-mdio + + # Deprecated + - allwinner,sun4i-mdio + + required: + - compatible + +properties: + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + compatible: + const: allwinner,sun4i-a10-mdio + + reg: + maxItems: 1 + + phy-supply: + description: PHY regulator + +required: + - compatible + - reg + +examples: + - | + mdio@1c0b080 { + compatible = "allwinner,sun4i-a10-mdio"; + reg = <0x01c0b080 0x14>; + #address-cells = <1>; + #size-cells = <0>; + phy-supply = <®_emac_3v3>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + }; + +# FIXME: We should set it, but it would report all the generic +# properties as additional properties. +# additionalProperties: false + +... diff --git a/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt b/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt deleted file mode 100644 index e98118aef5f6..000000000000 --- a/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt +++ /dev/null @@ -1,19 +0,0 @@ -* Allwinner EMAC ethernet controller - -Required properties: -- compatible: should be "allwinner,sun4i-a10-emac" (Deprecated: - "allwinner,sun4i-emac") -- reg: address and length of the register set for the device. -- interrupts: interrupt for the device -- phy: see ethernet.txt file in the same directory. -- clocks: A phandle to the reference clock for this device - -Example: - -emac: ethernet@1c0b000 { - compatible = "allwinner,sun4i-a10-emac"; - reg = <0x01c0b000 0x1000>; - interrupts = <55>; - clocks = <&ahb_gates 17>; - phy = <&phy0>; -}; diff --git a/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt b/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt deleted file mode 100644 index ab5b8613b0ef..000000000000 --- a/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt +++ /dev/null @@ -1,27 +0,0 @@ -* Allwinner A10 MDIO Ethernet Controller interface - -Required properties: -- compatible: should be "allwinner,sun4i-a10-mdio" - (Deprecated: "allwinner,sun4i-mdio"). -- reg: address and length of the register set for the device. - -Optional properties: -- phy-supply: phandle to a regulator if the PHY needs one - -Example at the SoC level: -mdio@1c0b080 { - compatible = "allwinner,sun4i-a10-mdio"; - reg = <0x01c0b080 0x14>; - #address-cells = <1>; - #size-cells = <0>; -}; - -And at the board level: - -mdio@1c0b080 { - phy-supply = <®_emac_3v3>; - - phy0: ethernet-phy@0 { - reg = <0>; - }; -}; diff --git a/Documentation/devicetree/bindings/net/allwinner,sun7i-a20-gmac.txt b/Documentation/devicetree/bindings/net/allwinner,sun7i-a20-gmac.txt deleted file mode 100644 index 8b3f953656e3..000000000000 --- a/Documentation/devicetree/bindings/net/allwinner,sun7i-a20-gmac.txt +++ /dev/null @@ -1,27 +0,0 @@ -* Allwinner GMAC ethernet controller - -This device is a platform glue layer for stmmac. -Please see stmmac.txt for the other unchanged properties. - -Required properties: - - compatible: Should be "allwinner,sun7i-a20-gmac" - - clocks: Should contain the GMAC main clock, and tx clock - The tx clock type should be "allwinner,sun7i-a20-gmac-clk" - - clock-names: Should contain the clock names "stmmaceth", - and "allwinner_gmac_tx" - -Optional properties: -- phy-supply: phandle to a regulator if the PHY needs one - -Examples: - - gmac: ethernet@1c50000 { - compatible = "allwinner,sun7i-a20-gmac"; - reg = <0x01c50000 0x10000>, - <0x01c20164 0x4>; - interrupts = <0 85 1>; - interrupt-names = "macirq"; - clocks = <&ahb_gates 49>, <&gmac_tx>; - clock-names = "stmmaceth", "allwinner_gmac_tx"; - phy-mode = "mii"; - }; diff --git a/Documentation/devicetree/bindings/net/allwinner,sun7i-a20-gmac.yaml b/Documentation/devicetree/bindings/net/allwinner,sun7i-a20-gmac.yaml new file mode 100644 index 000000000000..ef446ae166f3 --- /dev/null +++ b/Documentation/devicetree/bindings/net/allwinner,sun7i-a20-gmac.yaml @@ -0,0 +1,68 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/allwinner,sun7i-a20-gmac.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A20 GMAC Device Tree Bindings + +allOf: + - $ref: "snps,dwmac.yaml#" + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + compatible: + const: allwinner,sun7i-a20-gmac + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + interrupt-names: + const: macirq + + clocks: + items: + - description: GMAC main clock + - description: TX clock + + clock-names: + items: + - const: stmmaceth + - const: allwinner_gmac_tx + + phy-supply: + description: + PHY regulator + +required: + - compatible + - reg + - interrupts + - interrupt-names + - clocks + - clock-names + - phy-mode + +examples: + - | + gmac: ethernet@1c50000 { + compatible = "allwinner,sun7i-a20-gmac"; + reg = <0x01c50000 0x10000>; + interrupts = <0 85 1>; + interrupt-names = "macirq"; + clocks = <&ahb_gates 49>, <&gmac_tx>; + clock-names = "stmmaceth", "allwinner_gmac_tx"; + phy-mode = "mii"; + }; + +# FIXME: We should set it, but it would report all the generic +# properties as additional properties. +# additionalProperties: false + +... diff --git a/Documentation/devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml b/Documentation/devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml new file mode 100644 index 000000000000..3fb0714e761e --- /dev/null +++ b/Documentation/devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml @@ -0,0 +1,321 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/allwinner,sun8i-a83t-emac.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A83t EMAC Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + compatible: + oneOf: + - const: allwinner,sun8i-a83t-emac + - const: allwinner,sun8i-h3-emac + - const: allwinner,sun8i-r40-emac + - const: allwinner,sun8i-v3s-emac + - const: allwinner,sun50i-a64-emac + - items: + - const: allwinner,sun50i-h6-emac + - const: allwinner,sun50i-a64-emac + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + interrupt-names: + const: macirq + + clocks: + maxItems: 1 + + clock-names: + const: stmmaceth + + syscon: + $ref: /schemas/types.yaml#definitions/phandle + description: + Phandle to the device containing the EMAC or GMAC clock + register + +required: + - compatible + - reg + - interrupts + - interrupt-names + - clocks + - clock-names + - resets + - reset-names + - phy-handle + - phy-mode + - syscon + +allOf: + - $ref: "snps,dwmac.yaml#" + - if: + properties: + compatible: + contains: + enum: + - allwinner,sun8i-a83t-emac + - allwinner,sun8i-h3-emac + - allwinner,sun8i-v3s-emac + - allwinner,sun50i-a64-emac + + then: + properties: + allwinner,tx-delay-ps: + default: 0 + minimum: 0 + maximum: 700 + multipleOf: 100 + description: + External RGMII PHY TX clock delay chain value in ps. + + allwinner,rx-delay-ps: + default: 0 + minimum: 0 + maximum: 3100 + multipleOf: 100 + description: + External RGMII PHY TX clock delay chain value in ps. + + - if: + properties: + compatible: + contains: + enum: + - allwinner,sun8i-r40-emac + + then: + properties: + allwinner,rx-delay-ps: + default: 0 + minimum: 0 + maximum: 700 + multipleOf: 100 + description: + External RGMII PHY TX clock delay chain value in ps. + + - if: + properties: + compatible: + contains: + enum: + - allwinner,sun8i-h3-emac + - allwinner,sun8i-v3s-emac + + then: + properties: + allwinner,leds-active-low: + $ref: /schemas/types.yaml#definitions/flag + description: + EPHY LEDs are active low. + + mdio-mux: + type: object + + properties: + compatible: + const: allwinner,sun8i-h3-mdio-mux + + mdio-parent-bus: + $ref: /schemas/types.yaml#definitions/phandle + description: + Phandle to EMAC MDIO. + + mdio@1: + type: object + description: Internal MDIO Bus + + properties: + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + compatible: + const: allwinner,sun8i-h3-mdio-internal + + reg: + const: 1 + + patternProperties: + "^ethernet-phy@[0-9a-f]$": + type: object + description: + Integrated PHY node + + properties: + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + required: + - clocks + - resets + + + mdio@2: + type: object + description: External MDIO Bus (H3 only) + + properties: + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + reg: + const: 2 + + required: + - compatible + - mdio-parent-bus + - mdio@1 + +examples: + - | + ethernet@1c0b000 { + compatible = "allwinner,sun8i-h3-emac"; + syscon = <&syscon>; + reg = <0x01c0b000 0x104>; + interrupts = <0 82 1>; + interrupt-names = "macirq"; + resets = <&ccu 12>; + reset-names = "stmmaceth"; + clocks = <&ccu 27>; + clock-names = "stmmaceth"; + + phy-handle = <&int_mii_phy>; + phy-mode = "mii"; + allwinner,leds-active-low; + + mdio1: mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + }; + + mdio-mux { + compatible = "allwinner,sun8i-h3-mdio-mux"; + #address-cells = <1>; + #size-cells = <0>; + + mdio-parent-bus = <&mdio1>; + + int_mii_phy: mdio@1 { + compatible = "allwinner,sun8i-h3-mdio-internal"; + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + ethernet-phy@1 { + reg = <1>; + clocks = <&ccu 67>; + resets = <&ccu 39>; + phy-is-integrated; + }; + }; + + mdio@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + }; + + - | + ethernet@1c0b000 { + compatible = "allwinner,sun8i-h3-emac"; + syscon = <&syscon>; + reg = <0x01c0b000 0x104>; + interrupts = <0 82 1>; + interrupt-names = "macirq"; + resets = <&ccu 12>; + reset-names = "stmmaceth"; + clocks = <&ccu 27>; + clock-names = "stmmaceth"; + + phy-handle = <&ext_rgmii_phy>; + phy-mode = "rgmii"; + allwinner,leds-active-low; + + mdio2: mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + }; + + mdio-mux { + compatible = "allwinner,sun8i-h3-mdio-mux"; + #address-cells = <1>; + #size-cells = <0>; + mdio-parent-bus = <&mdio2>; + + mdio@1 { + compatible = "allwinner,sun8i-h3-mdio-internal"; + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + ethernet-phy@1 { + reg = <1>; + clocks = <&ccu 67>; + resets = <&ccu 39>; + }; + }; + + mdio@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + ext_rgmii_phy: ethernet-phy@1 { + reg = <1>; + }; + }; + }; + }; + + - | + ethernet@1c0b000 { + compatible = "allwinner,sun8i-a83t-emac"; + syscon = <&syscon>; + reg = <0x01c0b000 0x104>; + interrupts = <0 82 1>; + interrupt-names = "macirq"; + resets = <&ccu 13>; + reset-names = "stmmaceth"; + clocks = <&ccu 27>; + clock-names = "stmmaceth"; + phy-handle = <&ext_rgmii_phy1>; + phy-mode = "rgmii"; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + ext_rgmii_phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + }; + +# FIXME: We should set it, but it would report all the generic +# properties as additional properties. +# additionalProperties: false + +... diff --git a/Documentation/devicetree/bindings/net/amlogic,meson-dwmac.yaml b/Documentation/devicetree/bindings/net/amlogic,meson-dwmac.yaml new file mode 100644 index 000000000000..ae91aa9d8616 --- /dev/null +++ b/Documentation/devicetree/bindings/net/amlogic,meson-dwmac.yaml @@ -0,0 +1,113 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 BayLibre, SAS +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/net/amlogic,meson-dwmac.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Amlogic Meson DWMAC Ethernet controller + +maintainers: + - Neil Armstrong <narmstrong@baylibre.com> + - Martin Blumenstingl <martin.blumenstingl@googlemail.com> + +# We need a select here so we don't match all nodes with 'snps,dwmac' +select: + properties: + compatible: + contains: + enum: + - amlogic,meson6-dwmac + - amlogic,meson8b-dwmac + - amlogic,meson8m2-dwmac + - amlogic,meson-gxbb-dwmac + - amlogic,meson-axg-dwmac + required: + - compatible + +allOf: + - $ref: "snps,dwmac.yaml#" + - if: + properties: + compatible: + contains: + enum: + - amlogic,meson8b-dwmac + - amlogic,meson8m2-dwmac + - amlogic,meson-gxbb-dwmac + - amlogic,meson-axg-dwmac + + then: + properties: + clocks: + items: + - description: GMAC main clock + - description: First parent clock of the internal mux + - description: Second parent clock of the internal mux + + clock-names: + minItems: 3 + maxItems: 3 + items: + - const: stmmaceth + - const: clkin0 + - const: clkin1 + + amlogic,tx-delay-ns: + $ref: /schemas/types.yaml#definitions/uint32 + description: + The internal RGMII TX clock delay (provided by this driver) in + nanoseconds. Allowed values are 0ns, 2ns, 4ns, 6ns. + When phy-mode is set to "rgmii" then the TX delay should be + explicitly configured. When not configured a fallback of 2ns is + used. When the phy-mode is set to either "rgmii-id" or "rgmii-txid" + the TX clock delay is already provided by the PHY. In that case + this property should be set to 0ns (which disables the TX clock + delay in the MAC to prevent the clock from going off because both + PHY and MAC are adding a delay). + Any configuration is ignored when the phy-mode is set to "rmii". + +properties: + compatible: + additionalItems: true + maxItems: 3 + items: + - enum: + - amlogic,meson6-dwmac + - amlogic,meson8b-dwmac + - amlogic,meson8m2-dwmac + - amlogic,meson-gxbb-dwmac + - amlogic,meson-axg-dwmac + contains: + enum: + - snps,dwmac-3.70a + - snps,dwmac + + reg: + items: + - description: + The first register range should be the one of the DWMAC controller + - description: + The second range is is for the Amlogic specific configuration + (for example the PRG_ETHERNET register range on Meson8b and newer) + +required: + - compatible + - reg + - interrupts + - interrupt-names + - clocks + - clock-names + - phy-mode + +examples: + - | + ethmac: ethernet@c9410000 { + compatible = "amlogic,meson-gxbb-dwmac", "snps,dwmac"; + reg = <0xc9410000 0x10000>, <0xc8834540 0x8>; + interrupts = <8>; + interrupt-names = "macirq"; + clocks = <&clk_eth>, <&clkc_fclk_div2>, <&clk_mpll2>; + clock-names = "stmmaceth", "clkin0", "clkin1"; + phy-mode = "rgmii"; + }; diff --git a/Documentation/devicetree/bindings/net/aspeed,ast2600-mdio.yaml b/Documentation/devicetree/bindings/net/aspeed,ast2600-mdio.yaml new file mode 100644 index 000000000000..71808e78a495 --- /dev/null +++ b/Documentation/devicetree/bindings/net/aspeed,ast2600-mdio.yaml @@ -0,0 +1,45 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/aspeed,ast2600-mdio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ASPEED AST2600 MDIO Controller + +maintainers: + - Andrew Jeffery <andrew@aj.id.au> + +description: |+ + The ASPEED AST2600 MDIO controller is the third iteration of ASPEED's MDIO + bus register interface, this time also separating out the controller from the + MAC. + +allOf: + - $ref: "mdio.yaml#" + +properties: + compatible: + const: aspeed,ast2600-mdio + reg: + maxItems: 1 + description: The register range of the MDIO controller instance + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + +examples: + - | + mdio0: mdio@1e650000 { + compatible = "aspeed,ast2600-mdio"; + reg = <0x1e650000 0x8>; + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt index c26f4e11037c..4fa00e2eafcf 100644 --- a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt +++ b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt @@ -13,6 +13,7 @@ Required properties: * "brcm,bcm20702a1" * "brcm,bcm4330-bt" * "brcm,bcm43438-bt" + * "brcm,bcm4345c5" Optional properties: diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt index bc77477c6878..94c0f8bf4deb 100644 --- a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt +++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt @@ -32,6 +32,15 @@ Optional properties: ack_gpr is the gpr register offset of CAN stop acknowledge. ack_bit is the bit offset of CAN stop acknowledge. +- fsl,clk-source: Select the clock source to the CAN Protocol Engine (PE). + It's SoC Implementation dependent. Refer to RM for detailed + definition. If this property is not set in device tree node + then driver selects clock source 1 by default. + 0: clock source 0 (oscillator clock) + 1: clock source 1 (peripheral clock) + +- wakeup-source: enable CAN remote wakeup + Example: can@1c000 { @@ -40,4 +49,5 @@ Example: interrupts = <48 0x2>; interrupt-parent = <&mpic>; clock-frequency = <200000000>; // filled in by bootloader + fsl,clk-source = <0>; // select clock source 0 for PE }; diff --git a/Documentation/devicetree/bindings/net/can/rcar_can.txt b/Documentation/devicetree/bindings/net/can/rcar_can.txt index 9936b9ee67c3..19e4a7d91511 100644 --- a/Documentation/devicetree/bindings/net/can/rcar_can.txt +++ b/Documentation/devicetree/bindings/net/can/rcar_can.txt @@ -5,7 +5,9 @@ Required properties: - compatible: "renesas,can-r8a7743" if CAN controller is a part of R8A7743 SoC. "renesas,can-r8a7744" if CAN controller is a part of R8A7744 SoC. "renesas,can-r8a7745" if CAN controller is a part of R8A7745 SoC. + "renesas,can-r8a77470" if CAN controller is a part of R8A77470 SoC. "renesas,can-r8a774a1" if CAN controller is a part of R8A774A1 SoC. + "renesas,can-r8a774c0" if CAN controller is a part of R8A774C0 SoC. "renesas,can-r8a7778" if CAN controller is a part of R8A7778 SoC. "renesas,can-r8a7779" if CAN controller is a part of R8A7779 SoC. "renesas,can-r8a7790" if CAN controller is a part of R8A7790 SoC. @@ -16,6 +18,8 @@ Required properties: "renesas,can-r8a7795" if CAN controller is a part of R8A7795 SoC. "renesas,can-r8a7796" if CAN controller is a part of R8A7796 SoC. "renesas,can-r8a77965" if CAN controller is a part of R8A77965 SoC. + "renesas,can-r8a77990" if CAN controller is a part of R8A77990 SoC. + "renesas,can-r8a77995" if CAN controller is a part of R8A77995 SoC. "renesas,rcar-gen1-can" for a generic R-Car Gen1 compatible device. "renesas,rcar-gen2-can" for a generic R-Car Gen2 or RZ/G1 compatible device. @@ -27,17 +31,13 @@ Required properties: - reg: physical base address and size of the R-Car CAN register map. - interrupts: interrupt specifier for the sole interrupt. -- clocks: phandles and clock specifiers for 2 CAN clock inputs for RZ/G2 - devices. - phandles and clock specifiers for 3 CAN clock inputs for every other - SoC. -- clock-names: 2 clock input name strings for RZ/G2: "clkp1", "can_clk". - 3 clock input name strings for every other SoC: "clkp1", "clkp2", - "can_clk". +- clocks: phandles and clock specifiers for 3 CAN clock inputs. +- clock-names: 3 clock input name strings: "clkp1", "clkp2", and "can_clk". - pinctrl-0: pin control group to be used for this controller. - pinctrl-names: must be "default". -Required properties for R8A7795, R8A7796 and R8A77965: +Required properties for R8A774A1, R8A774C0, R8A7795, R8A7796, R8A77965, +R8A77990, and R8A77995: For the denoted SoCs, "clkp2" can be CANFD clock. This is a div6 clock and can be used by both CAN and CAN FD controller at the same time. It needs to be scaled to maximum frequency if any of these controllers use it. This is done @@ -49,8 +49,7 @@ using the below properties: Optional properties: - renesas,can-clock-select: R-Car CAN Clock Source Select. Valid values are: <0x0> (default) : Peripheral clock (clkp1) - <0x1> : Peripheral clock (clkp2) (not supported by - RZ/G2 devices) + <0x1> : Peripheral clock (clkp2) <0x3> : External input clock Example diff --git a/Documentation/devicetree/bindings/net/can/rcar_canfd.txt b/Documentation/devicetree/bindings/net/can/rcar_canfd.txt index ac71daa46195..a901cd9be29e 100644 --- a/Documentation/devicetree/bindings/net/can/rcar_canfd.txt +++ b/Documentation/devicetree/bindings/net/can/rcar_canfd.txt @@ -3,11 +3,16 @@ Renesas R-Car CAN FD controller Device Tree Bindings Required properties: - compatible: Must contain one or more of the following: - - "renesas,rcar-gen3-canfd" for R-Car Gen3 compatible controller. + - "renesas,rcar-gen3-canfd" for R-Car Gen3 and RZ/G2 compatible controllers. + - "renesas,r8a774a1-canfd" for R8A774A1 (RZ/G2M) compatible controller. + - "renesas,r8a774c0-canfd" for R8A774C0 (RZ/G2E) compatible controller. - "renesas,r8a7795-canfd" for R8A7795 (R-Car H3) compatible controller. - "renesas,r8a7796-canfd" for R8A7796 (R-Car M3-W) compatible controller. + - "renesas,r8a77965-canfd" for R8A77965 (R-Car M3-N) compatible controller. - "renesas,r8a77970-canfd" for R8A77970 (R-Car V3M) compatible controller. - "renesas,r8a77980-canfd" for R8A77980 (R-Car V3H) compatible controller. + - "renesas,r8a77990-canfd" for R8A77990 (R-Car E3) compatible controller. + - "renesas,r8a77995-canfd" for R8A77995 (R-Car D3) compatible controller. When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first, followed by the @@ -26,10 +31,10 @@ The name of the child nodes are "channel0" and "channel1" respectively. Each child node supports the "status" property only, which is used to enable/disable the respective channel. -Required properties for "renesas,r8a7795-canfd" and "renesas,r8a7796-canfd" -compatible: -In R8A7795 and R8A7796 SoCs, canfd clock is a div6 clock and can be used by both -CAN and CAN FD controller at the same time. It needs to be scaled to maximum +Required properties for R8A774A1, R8A774C0, R8A7795, R8A7796, R8A77965, +R8A77990, and R8A77995: +In the denoted SoCs, canfd clock is a div6 clock and can be used by both CAN +and CAN FD controller at the same time. It needs to be scaled to maximum frequency if any of these controllers use it. This is done using the below properties: diff --git a/Documentation/devicetree/bindings/net/can/tcan4x5x.txt b/Documentation/devicetree/bindings/net/can/tcan4x5x.txt new file mode 100644 index 000000000000..27e1b4cebfbd --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/tcan4x5x.txt @@ -0,0 +1,40 @@ +Texas Instruments TCAN4x5x CAN Controller +================================================ + +This file provides device node information for the TCAN4x5x interface contains. + +Required properties: + - compatible: "ti,tcan4x5x" + - reg: 0 + - #address-cells: 1 + - #size-cells: 0 + - spi-max-frequency: Maximum frequency of the SPI bus the chip can + operate at should be less than or equal to 18 MHz. + - device-wake-gpios: Wake up GPIO to wake up the TCAN device. + - interrupt-parent: the phandle to the interrupt controller which provides + the interrupt. + - interrupts: interrupt specification for data-ready. + +See Documentation/devicetree/bindings/net/can/m_can.txt for additional +required property details. + +Optional properties: + - reset-gpios: Hardwired output GPIO. If not defined then software + reset. + - device-state-gpios: Input GPIO that indicates if the device is in + a sleep state or if the device is active. + +Example: +tcan4x5x: tcan4x5x@0 { + compatible = "ti,tcan4x5x"; + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <10000000>; + bosch,mram-cfg = <0x0 0 0 32 0 0 1 1>; + interrupt-parent = <&gpio1>; + interrupts = <14 GPIO_ACTIVE_LOW>; + device-state-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>; + device-wake-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>; +}; diff --git a/Documentation/devicetree/bindings/net/dsa/ksz.txt b/Documentation/devicetree/bindings/net/dsa/ksz.txt index e7db7268fd0f..95e91e84151c 100644 --- a/Documentation/devicetree/bindings/net/dsa/ksz.txt +++ b/Documentation/devicetree/bindings/net/dsa/ksz.txt @@ -5,6 +5,9 @@ Required properties: - compatible: For external switch chips, compatible string must be exactly one of the following: + - "microchip,ksz8765" + - "microchip,ksz8794" + - "microchip,ksz8795" - "microchip,ksz9477" - "microchip,ksz9897" - "microchip,ksz9896" @@ -12,10 +15,13 @@ Required properties: - "microchip,ksz8565" - "microchip,ksz9893" - "microchip,ksz9563" + - "microchip,ksz8563" Optional properties: - reset-gpios : Should be a gpio specifier for a reset line +- microchip,synclko-125 : Set if the output SYNCLKO frequency should be set to + 125MHz instead of 25MHz. See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional required and optional properties. diff --git a/Documentation/devicetree/bindings/net/dsa/marvell.txt b/Documentation/devicetree/bindings/net/dsa/marvell.txt index feb007af13cb..30c11fea491b 100644 --- a/Documentation/devicetree/bindings/net/dsa/marvell.txt +++ b/Documentation/devicetree/bindings/net/dsa/marvell.txt @@ -21,10 +21,13 @@ which is at a different MDIO base address in different switch families. 6341, 6350, 6351, 6352 - "marvell,mv88e6190" : Switch has base address 0x00. Use with models: 6190, 6190X, 6191, 6290, 6390, 6390X +- "marvell,mv88e6250" : Switch has base address 0x08 or 0x18. Use with model: + 6220, 6250 Required properties: -- compatible : Should be one of "marvell,mv88e6085" or - "marvell,mv88e6190" as indicated above +- compatible : Should be one of "marvell,mv88e6085", + "marvell,mv88e6190" or "marvell,mv88e6250" as + indicated above - reg : Address on the MII bus for the switch. Optional properties: diff --git a/Documentation/devicetree/bindings/net/dsa/mt7530.txt b/Documentation/devicetree/bindings/net/dsa/mt7530.txt index 47aa205ee0bd..c5ed5d25f642 100644 --- a/Documentation/devicetree/bindings/net/dsa/mt7530.txt +++ b/Documentation/devicetree/bindings/net/dsa/mt7530.txt @@ -35,6 +35,42 @@ Required properties for the child nodes within ports container: - phy-mode: String, must be either "trgmii" or "rgmii" for port labeled "cpu". +Port 5 of the switch is muxed between: +1. GMAC5: GMAC5 can interface with another external MAC or PHY. +2. PHY of port 0 or port 4: PHY interfaces with an external MAC like 2nd GMAC + of the SOC. Used in many setups where port 0/4 becomes the WAN port. + Note: On a MT7621 SOC with integrated switch: 2nd GMAC can only connected to + GMAC5 when the gpios for RGMII2 (GPIO 22-33) are not used and not + connected to external component! + +Port 5 modes/configurations: +1. Port 5 is disabled and isolated: An external phy can interface to the 2nd + GMAC of the SOC. + In the case of a build-in MT7530 switch, port 5 shares the RGMII bus with 2nd + GMAC and an optional external phy. Mind the GPIO/pinctl settings of the SOC! +2. Port 5 is muxed to PHY of port 0/4: Port 0/4 interfaces with 2nd GMAC. + It is a simple MAC to PHY interface, port 5 needs to be setup for xMII mode + and RGMII delay. +3. Port 5 is muxed to GMAC5 and can interface to an external phy. + Port 5 becomes an extra switch port. + Only works on platform where external phy TX<->RX lines are swapped. + Like in the Ubiquiti ER-X-SFP. +4. Port 5 is muxed to GMAC5 and interfaces with the 2nd GAMC as 2nd CPU port. + Currently a 2nd CPU port is not supported by DSA code. + +Depending on how the external PHY is wired: +1. normal: The PHY can only connect to 2nd GMAC but not to the switch +2. swapped: RGMII TX, RX are swapped; external phy interface with the switch as + a ethernet port. But can't interface to the 2nd GMAC. + +Based on the DT the port 5 mode is configured. + +Driver tries to lookup the phy-handle of the 2nd GMAC of the master device. +When phy-handle matches PHY of port 0 or 4 then port 5 set-up as mode 2. +phy-mode must be set, see also example 2 below! + * mt7621: phy-mode = "rgmii-txid"; + * mt7623: phy-mode = "rgmii"; + See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional required, optional properties and how the integrated switch subnodes must be specified. @@ -94,3 +130,181 @@ Example: }; }; }; + +Example 2: MT7621: Port 4 is WAN port: 2nd GMAC -> Port 5 -> PHY port 4. + +ð { + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "rgmii-txid"; + phy-handle = <&phy4>; + }; + + mdio: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + + /* Internal phy */ + phy4: ethernet-phy@4 { + reg = <4>; + }; + + mt7530: switch@1f { + compatible = "mediatek,mt7621"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x1f>; + pinctrl-names = "default"; + mediatek,mcm; + + resets = <&rstctrl 2>; + reset-names = "mcm"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan0"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + +/* Commented out. Port 4 is handled by 2nd GMAC. + port@4 { + reg = <4>; + label = "lan4"; + }; +*/ + + cpu_port0: port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; +}; + +Example 3: MT7621: Port 5 is connected to external PHY: Port 5 -> external PHY. + +ð { + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + + mdio: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + + /* External phy */ + ephy5: ethernet-phy@7 { + reg = <7>; + }; + + mt7530: switch@1f { + compatible = "mediatek,mt7621"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x1f>; + pinctrl-names = "default"; + mediatek,mcm; + + resets = <&rstctrl 2>; + reset-names = "mcm"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan0"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "lan4"; + }; + + port@5 { + reg = <5>; + label = "lan5"; + phy-mode = "rgmii"; + phy-handle = <&ephy5>; + }; + + cpu_port0: port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.txt b/Documentation/devicetree/bindings/net/dsa/qca8k.txt index 93a7469e70d4..ccbc6d89325d 100644 --- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt +++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt @@ -9,6 +9,10 @@ Required properties: - #size-cells: must be 0 - #address-cells: must be 1 +Optional properties: + +- reset-gpios: GPIO to be used to reset the whole device + Subnodes: The integrated switch subnode should be specified according to the binding @@ -66,6 +70,7 @@ for the external mdio-bus configuration: #address-cells = <1>; #size-cells = <0>; + reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; reg = <0x10>; ports { @@ -123,6 +128,7 @@ for the internal master mdio-bus configuration: #address-cells = <1>; #size-cells = <0>; + reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; reg = <0x10>; ports { diff --git a/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt b/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt index ed4710c40641..bbf4a13f6d75 100644 --- a/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt +++ b/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt @@ -2,8 +2,8 @@ Vitesse VSC73xx Switches ======================== This defines device tree bindings for the Vitesse VSC73xx switch chips. -The Vitesse company has been acquired by Microsemi and Microsemi in turn -acquired by Microchip but retains this vendor branding. +The Vitesse company has been acquired by Microsemi and Microsemi has +been acquired Microchip but retains this vendor branding. The currently supported switch chips are: Vitesse VSC7385 SparX-G5 5+1-port Integrated Gigabit Ethernet Switch @@ -11,8 +11,14 @@ Vitesse VSC7388 SparX-G8 8-port Integrated Gigabit Ethernet Switch Vitesse VSC7395 SparX-G5e 5+1-port Integrated Gigabit Ethernet Switch Vitesse VSC7398 SparX-G8e 8-port Integrated Gigabit Ethernet Switch -The device tree node is an SPI device so it must reside inside a SPI bus -device tree node, see spi/spi-bus.txt +This switch could have two different management interface. + +If SPI interface is used, the device tree node is an SPI device so it must +reside inside a SPI bus device tree node, see spi/spi-bus.txt + +When the chip is connected to a parallel memory bus and work in memory-mapped +I/O mode, a platform device is used to represent the vsc73xx. In this case it +must reside inside a platform bus device tree node. Required properties: @@ -38,6 +44,7 @@ and subnodes of DSA switches. Examples: +SPI: switch@0 { compatible = "vitesse,vsc7395"; reg = <0>; @@ -79,3 +86,46 @@ switch@0 { }; }; }; + +Platform: +switch@2,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "vitesse,vsc7385"; + reg = <0x2 0x0 0x20000>; + reset-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + port@1 { + reg = <1>; + label = "lan2"; + }; + port@2 { + reg = <2>; + label = "lan3"; + }; + port@3 { + reg = <3>; + label = "lan4"; + }; + vsc: port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&enet0>; + phy-mode = "rgmii"; + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + +}; diff --git a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt deleted file mode 100644 index 54c66d0611cb..000000000000 --- a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt +++ /dev/null @@ -1,201 +0,0 @@ -* Allwinner sun8i GMAC ethernet controller - -This device is a platform glue layer for stmmac. -Please see stmmac.txt for the other unchanged properties. - -Required properties: -- compatible: must be one of the following string: - "allwinner,sun8i-a83t-emac" - "allwinner,sun8i-h3-emac" - "allwinner,sun8i-r40-gmac" - "allwinner,sun8i-v3s-emac" - "allwinner,sun50i-a64-emac" - "allwinner,sun50i-h6-emac", "allwinner-sun50i-a64-emac" -- reg: address and length of the register for the device. -- interrupts: interrupt for the device -- interrupt-names: must be "macirq" -- clocks: A phandle to the reference clock for this device -- clock-names: must be "stmmaceth" -- resets: A phandle to the reset control for this device -- reset-names: must be "stmmaceth" -- phy-mode: See ethernet.txt -- phy-handle: See ethernet.txt -- syscon: A phandle to the device containing the EMAC or GMAC clock register - -Optional properties: -- allwinner,tx-delay-ps: TX clock delay chain value in ps. - Range is 0-700. Default is 0. - Unavailable for allwinner,sun8i-r40-gmac -- allwinner,rx-delay-ps: RX clock delay chain value in ps. - Range is 0-3100. Default is 0. - Range is 0-700 for allwinner,sun8i-r40-gmac -Both delay properties need to be a multiple of 100. They control the -clock delay for external RGMII PHY. They do not apply to the internal -PHY or external non-RGMII PHYs. - -Optional properties for the following compatibles: - - "allwinner,sun8i-h3-emac", - - "allwinner,sun8i-v3s-emac": -- allwinner,leds-active-low: EPHY LEDs are active low - -Required child node of emac: -- mdio bus node: should be named mdio with compatible "snps,dwmac-mdio" - -Required properties of the mdio node: -- #address-cells: shall be 1 -- #size-cells: shall be 0 - -The device node referenced by "phy" or "phy-handle" must be a child node -of the mdio node. See phy.txt for the generic PHY bindings. - -The following compatibles require that the emac node have a mdio-mux child -node called "mdio-mux": - - "allwinner,sun8i-h3-emac" - - "allwinner,sun8i-v3s-emac": -Required properties for the mdio-mux node: - - compatible = "allwinner,sun8i-h3-mdio-mux" - - mdio-parent-bus: a phandle to EMAC mdio - - one child mdio for the integrated mdio with the compatible - "allwinner,sun8i-h3-mdio-internal" - - one child mdio for the external mdio if present (V3s have none) -Required properties for the mdio-mux children node: - - reg: 1 for internal MDIO bus, 2 for external MDIO bus - -The following compatibles require a PHY node representing the integrated -PHY, under the integrated MDIO bus node if an mdio-mux node is used: - - "allwinner,sun8i-h3-emac", - - "allwinner,sun8i-v3s-emac": - -Additional information regarding generic multiplexer properties can be found -at Documentation/devicetree/bindings/net/mdio-mux.txt - -Required properties of the integrated phy node: -- clocks: a phandle to the reference clock for the EPHY -- resets: a phandle to the reset control for the EPHY -- Must be a child of the integrated mdio - -Example with integrated PHY: -emac: ethernet@1c0b000 { - compatible = "allwinner,sun8i-h3-emac"; - syscon = <&syscon>; - reg = <0x01c0b000 0x104>; - interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "macirq"; - resets = <&ccu RST_BUS_EMAC>; - reset-names = "stmmaceth"; - clocks = <&ccu CLK_BUS_EMAC>; - clock-names = "stmmaceth"; - - phy-handle = <&int_mii_phy>; - phy-mode = "mii"; - allwinner,leds-active-low; - - mdio: mdio { - #address-cells = <1>; - #size-cells = <0>; - compatible = "snps,dwmac-mdio"; - }; - - mdio-mux { - compatible = "mdio-mux", "allwinner,sun8i-h3-mdio-mux"; - #address-cells = <1>; - #size-cells = <0>; - - mdio-parent-bus = <&mdio>; - - int_mdio: mdio@1 { - compatible = "allwinner,sun8i-h3-mdio-internal"; - reg = <1>; - #address-cells = <1>; - #size-cells = <0>; - int_mii_phy: ethernet-phy@1 { - reg = <1>; - clocks = <&ccu CLK_BUS_EPHY>; - resets = <&ccu RST_BUS_EPHY>; - phy-is-integrated; - }; - }; - ext_mdio: mdio@2 { - reg = <2>; - #address-cells = <1>; - #size-cells = <0>; - }; - }; -}; - -Example with external PHY: -emac: ethernet@1c0b000 { - compatible = "allwinner,sun8i-h3-emac"; - syscon = <&syscon>; - reg = <0x01c0b000 0x104>; - interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "macirq"; - resets = <&ccu RST_BUS_EMAC>; - reset-names = "stmmaceth"; - clocks = <&ccu CLK_BUS_EMAC>; - clock-names = "stmmaceth"; - - phy-handle = <&ext_rgmii_phy>; - phy-mode = "rgmii"; - allwinner,leds-active-low; - - mdio: mdio { - #address-cells = <1>; - #size-cells = <0>; - compatible = "snps,dwmac-mdio"; - }; - - mdio-mux { - compatible = "allwinner,sun8i-h3-mdio-mux"; - #address-cells = <1>; - #size-cells = <0>; - - mdio-parent-bus = <&mdio>; - - int_mdio: mdio@1 { - compatible = "allwinner,sun8i-h3-mdio-internal"; - reg = <1>; - #address-cells = <1>; - #size-cells = <0>; - int_mii_phy: ethernet-phy@1 { - reg = <1>; - clocks = <&ccu CLK_BUS_EPHY>; - resets = <&ccu RST_BUS_EPHY>; - }; - }; - ext_mdio: mdio@2 { - reg = <2>; - #address-cells = <1>; - #size-cells = <0>; - ext_rgmii_phy: ethernet-phy@1 { - reg = <1>; - }; - }: - }; -}; - -Example with SoC without integrated PHY - -emac: ethernet@1c0b000 { - compatible = "allwinner,sun8i-a83t-emac"; - syscon = <&syscon>; - reg = <0x01c0b000 0x104>; - interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "macirq"; - resets = <&ccu RST_BUS_EMAC>; - reset-names = "stmmaceth"; - clocks = <&ccu CLK_BUS_EMAC>; - clock-names = "stmmaceth"; - - phy-handle = <&ext_rgmii_phy>; - phy-mode = "rgmii"; - - mdio: mdio { - compatible = "snps,dwmac-mdio"; - #address-cells = <1>; - #size-cells = <0>; - ext_rgmii_phy: ethernet-phy@1 { - reg = <1>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/net/ethernet-controller.yaml b/Documentation/devicetree/bindings/net/ethernet-controller.yaml new file mode 100644 index 000000000000..0e7c31794ae6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ethernet-controller.yaml @@ -0,0 +1,206 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/ethernet-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ethernet Controller Generic Binding + +maintainers: + - David S. Miller <davem@davemloft.net> + +properties: + $nodename: + pattern: "^ethernet(@.*)?$" + + local-mac-address: + allOf: + - $ref: /schemas/types.yaml#definitions/uint8-array + - items: + - minItems: 6 + maxItems: 6 + description: + Specifies the MAC address that was assigned to the network device. + + mac-address: + allOf: + - $ref: /schemas/types.yaml#definitions/uint8-array + - items: + - minItems: 6 + maxItems: 6 + description: + Specifies the MAC address that was last used by the boot + program; should be used in cases where the MAC address assigned + to the device by the boot program is different from the + local-mac-address property. + + max-frame-size: + $ref: /schemas/types.yaml#definitions/uint32 + description: + Maximum transfer unit (IEEE defined MTU), rather than the + maximum frame size (there\'s contradiction in the Devicetree + Specification). + + max-speed: + $ref: /schemas/types.yaml#definitions/uint32 + description: + Specifies maximum speed in Mbit/s supported by the device. + + nvmem-cells: + maxItems: 1 + description: + Reference to an nvmem node for the MAC address + + nvmem-cells-names: + const: mac-address + + phy-connection-type: + description: + Operation mode of the PHY interface + enum: + # There is not a standard bus between the MAC and the PHY, + # something proprietary is being used to embed the PHY in the + # MAC. + - internal + - mii + - gmii + - sgmii + - qsgmii + - tbi + - rev-mii + - rmii + + # RX and TX delays are added by the MAC when required + - rgmii + + # RGMII with internal RX and TX delays provided by the PHY, + # the MAC should not add the RX or TX delays in this case + - rgmii-id + + # RGMII with internal RX delay provided by the PHY, the MAC + # should not add an RX delay in this case + - rgmii-rxid + + # RGMII with internal TX delay provided by the PHY, the MAC + # should not add an TX delay in this case + - rgmii-txid + - rtbi + - smii + - xgmii + - trgmii + - 1000base-x + - 2500base-x + - rxaui + - xaui + + # 10GBASE-KR, XFI, SFI + - 10gbase-kr + - usxgmii + + phy-mode: + $ref: "#/properties/phy-connection-type" + + phy-handle: + $ref: /schemas/types.yaml#definitions/phandle + description: + Specifies a reference to a node representing a PHY device. + + phy: + $ref: "#/properties/phy-handle" + deprecated: true + + phy-device: + $ref: "#/properties/phy-handle" + deprecated: true + + rx-fifo-depth: + $ref: /schemas/types.yaml#definitions/uint32 + description: + The size of the controller\'s receive fifo in bytes. This is used + for components that can have configurable receive fifo sizes, + and is useful for determining certain configuration settings + such as flow control thresholds. + + tx-fifo-depth: + $ref: /schemas/types.yaml#definitions/uint32 + description: + The size of the controller\'s transmit fifo in bytes. This + is used for components that can have configurable fifo sizes. + + managed: + allOf: + - $ref: /schemas/types.yaml#definitions/string + - default: auto + enum: + - auto + - in-band-status + description: + Specifies the PHY management type. If auto is set and fixed-link + is not specified, it uses MDIO for management. + + fixed-link: + allOf: + - if: + type: array + then: + deprecated: true + minItems: 1 + maxItems: 1 + items: + items: + - minimum: 0 + maximum: 31 + description: + Emulated PHY ID, choose any but unique to the all + specified fixed-links + + - enum: [0, 1] + description: + Duplex configuration. 0 for half duplex or 1 for + full duplex + + - enum: [10, 100, 1000] + description: + Link speed in Mbits/sec. + + - enum: [0, 1] + description: + Pause configuration. 0 for no pause, 1 for pause + + - enum: [0, 1] + description: + Asymmetric pause configuration. 0 for no asymmetric + pause, 1 for asymmetric pause + + + - if: + type: object + then: + properties: + speed: + allOf: + - $ref: /schemas/types.yaml#definitions/uint32 + - enum: [10, 100, 1000] + description: + Link speed. + + full-duplex: + $ref: /schemas/types.yaml#definitions/flag + description: + Indicates that full-duplex is used. When absent, half + duplex is assumed. + + asym-pause: + $ref: /schemas/types.yaml#definitions/flag + description: + Indicates that asym_pause should be enabled. + + link-gpios: + maxItems: 1 + description: + GPIO to determine if the link is up + + required: + - speed + +... diff --git a/Documentation/devicetree/bindings/net/ethernet-phy.yaml b/Documentation/devicetree/bindings/net/ethernet-phy.yaml new file mode 100644 index 000000000000..f70f18ff821f --- /dev/null +++ b/Documentation/devicetree/bindings/net/ethernet-phy.yaml @@ -0,0 +1,177 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/ethernet-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ethernet PHY Generic Binding + +maintainers: + - Andrew Lunn <andrew@lunn.ch> + - Florian Fainelli <f.fainelli@gmail.com> + - Heiner Kallweit <hkallweit1@gmail.com> + +# The dt-schema tools will generate a select statement first by using +# the compatible, and second by using the node name if any. In our +# case, the node name is the one we want to match on, while the +# compatible is optional. +select: + properties: + $nodename: + pattern: "^ethernet-phy(@[a-f0-9]+)?$" + + required: + - $nodename + +properties: + $nodename: + pattern: "^ethernet-phy(@[a-f0-9]+)?$" + + compatible: + oneOf: + - const: ethernet-phy-ieee802.3-c22 + description: PHYs that implement IEEE802.3 clause 22 + - const: ethernet-phy-ieee802.3-c45 + description: PHYs that implement IEEE802.3 clause 45 + - pattern: "^ethernet-phy-id[a-f0-9]{4}\\.[a-f0-9]{4}$" + description: + If the PHY reports an incorrect ID (or none at all) then the + compatible list may contain an entry with the correct PHY ID + in the above form. + The first group of digits is the 16 bit Phy Identifier 1 + register, this is the chip vendor OUI bits 3:18. The + second group of digits is the Phy Identifier 2 register, + this is the chip vendor OUI bits 19:24, followed by 10 + bits of a vendor specific ID. + - items: + - pattern: "^ethernet-phy-id[a-f0-9]{4}\\.[a-f0-9]{4}$" + - const: ethernet-phy-ieee802.3-c45 + + reg: + minimum: 0 + maximum: 31 + description: + The ID number for the PHY. + + interrupts: + maxItems: 1 + + max-speed: + enum: + - 10 + - 100 + - 1000 + - 2500 + - 5000 + - 10000 + - 20000 + - 25000 + - 40000 + - 50000 + - 56000 + - 100000 + - 200000 + description: + Maximum PHY supported speed in Mbits / seconds. + + broken-turn-around: + $ref: /schemas/types.yaml#definitions/flag + description: + If set, indicates the PHY device does not correctly release + the turn around line low at the end of a MDIO transaction. + + enet-phy-lane-swap: + $ref: /schemas/types.yaml#definitions/flag + description: + If set, indicates the PHY will swap the TX/RX lanes to + compensate for the board being designed with the lanes + swapped. + + eee-broken-100tx: + $ref: /schemas/types.yaml#definitions/flag + description: + Mark the corresponding energy efficient ethernet mode as + broken and request the ethernet to stop advertising it. + + eee-broken-1000t: + $ref: /schemas/types.yaml#definitions/flag + description: + Mark the corresponding energy efficient ethernet mode as + broken and request the ethernet to stop advertising it. + + eee-broken-10gt: + $ref: /schemas/types.yaml#definitions/flag + description: + Mark the corresponding energy efficient ethernet mode as + broken and request the ethernet to stop advertising it. + + eee-broken-1000kx: + $ref: /schemas/types.yaml#definitions/flag + description: + Mark the corresponding energy efficient ethernet mode as + broken and request the ethernet to stop advertising it. + + eee-broken-10gkx4: + $ref: /schemas/types.yaml#definitions/flag + description: + Mark the corresponding energy efficient ethernet mode as + broken and request the ethernet to stop advertising it. + + eee-broken-10gkr: + $ref: /schemas/types.yaml#definitions/flag + description: + Mark the corresponding energy efficient ethernet mode as + broken and request the ethernet to stop advertising it. + + phy-is-integrated: + $ref: /schemas/types.yaml#definitions/flag + description: + If set, indicates that the PHY is integrated into the same + physical package as the Ethernet MAC. If needed, muxers + should be configured to ensure the integrated PHY is + used. The absence of this property indicates the muxers + should be configured so that the external PHY is used. + + resets: + maxItems: 1 + + reset-names: + const: phy + + reset-gpios: + maxItems: 1 + description: + The GPIO phandle and specifier for the PHY reset signal. + + reset-assert-us: + description: + Delay after the reset was asserted in microseconds. If this + property is missing the delay will be skipped. + + reset-deassert-us: + description: + Delay after the reset was deasserted in microseconds. If + this property is missing the delay will be skipped. + +required: + - reg + +examples: + - | + ethernet { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-phy@0 { + compatible = "ethernet-phy-id0141.0e90", "ethernet-phy-ieee802.3-c45"; + interrupt-parent = <&PIC>; + interrupts = <35 1>; + reg = <0>; + + resets = <&rst 8>; + reset-names = "phy"; + reset-gpios = <&gpio1 4 1>; + reset-assert-us = <1000>; + reset-deassert-us = <2000>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/ethernet.txt b/Documentation/devicetree/bindings/net/ethernet.txt index e88c3641d613..5df413d01be2 100644 --- a/Documentation/devicetree/bindings/net/ethernet.txt +++ b/Documentation/devicetree/bindings/net/ethernet.txt @@ -1,67 +1 @@ -The following properties are common to the Ethernet controllers: - -NOTE: All 'phy*' properties documented below are Ethernet specific. For the -generic PHY 'phys' property, see -Documentation/devicetree/bindings/phy/phy-bindings.txt. - -- mac-address: array of 6 bytes, specifies the MAC address that was last used by - the boot program; should be used in cases where the MAC address assigned to - the device by the boot program is different from the "local-mac-address" - property; -- local-mac-address: array of 6 bytes, specifies the MAC address that was - assigned to the network device; -- nvmem-cells: phandle, reference to an nvmem node for the MAC address -- nvmem-cell-names: string, should be "mac-address" if nvmem is to be used -- max-speed: number, specifies maximum speed in Mbit/s supported by the device; -- max-frame-size: number, maximum transfer unit (IEEE defined MTU), rather than - the maximum frame size (there's contradiction in the Devicetree - Specification). -- phy-mode: string, operation mode of the PHY interface. This is now a de-facto - standard property; supported values are: - * "internal" (Internal means there is not a standard bus between the MAC and - the PHY, something proprietary is being used to embed the PHY in the MAC.) - * "mii" - * "gmii" - * "sgmii" - * "qsgmii" - * "tbi" - * "rev-mii" - * "rmii" - * "rgmii" (RX and TX delays are added by the MAC when required) - * "rgmii-id" (RGMII with internal RX and TX delays provided by the PHY, the - MAC should not add the RX or TX delays in this case) - * "rgmii-rxid" (RGMII with internal RX delay provided by the PHY, the MAC - should not add an RX delay in this case) - * "rgmii-txid" (RGMII with internal TX delay provided by the PHY, the MAC - should not add an TX delay in this case) - * "rtbi" - * "smii" - * "xgmii" - * "trgmii" - * "1000base-x", - * "2500base-x", - * "rxaui" - * "xaui" - * "10gbase-kr" (10GBASE-KR, XFI, SFI) -- phy-connection-type: the same as "phy-mode" property but described in the - Devicetree Specification; -- phy-handle: phandle, specifies a reference to a node representing a PHY - device; this property is described in the Devicetree Specification and so - preferred; -- phy: the same as "phy-handle" property, not recommended for new bindings. -- phy-device: the same as "phy-handle" property, not recommended for new - bindings. -- rx-fifo-depth: the size of the controller's receive fifo in bytes. This - is used for components that can have configurable receive fifo sizes, - and is useful for determining certain configuration settings such as - flow control thresholds. -- tx-fifo-depth: the size of the controller's transmit fifo in bytes. This - is used for components that can have configurable fifo sizes. -- managed: string, specifies the PHY management type. Supported values are: - "auto", "in-band-status". "auto" is the default, it usess MDIO for - management if fixed-link is not specified. - -Child nodes of the Ethernet controller are typically the individual PHY devices -connected via the MDIO bus (sometimes the MDIO bus controller is separate). -They are described in the phy.txt file in this same directory. -For non-MDIO PHY management see fixed-link.txt. +This file has moved to ethernet-controller.yaml. diff --git a/Documentation/devicetree/bindings/net/fixed-link.txt b/Documentation/devicetree/bindings/net/fixed-link.txt index ec5d889fe3d8..5df413d01be2 100644 --- a/Documentation/devicetree/bindings/net/fixed-link.txt +++ b/Documentation/devicetree/bindings/net/fixed-link.txt @@ -1,54 +1 @@ -Fixed link Device Tree binding ------------------------------- - -Some Ethernet MACs have a "fixed link", and are not connected to a -normal MDIO-managed PHY device. For those situations, a Device Tree -binding allows to describe a "fixed link". - -Such a fixed link situation is described by creating a 'fixed-link' -sub-node of the Ethernet MAC device node, with the following -properties: - -* 'speed' (integer, mandatory), to indicate the link speed. Accepted - values are 10, 100 and 1000 -* 'full-duplex' (boolean, optional), to indicate that full duplex is - used. When absent, half duplex is assumed. -* 'pause' (boolean, optional), to indicate that pause should be - enabled. -* 'asym-pause' (boolean, optional), to indicate that asym_pause should - be enabled. -* 'link-gpios' ('gpio-list', optional), to indicate if a gpio can be read - to determine if the link is up. - -Old, deprecated 'fixed-link' binding: - -* A 'fixed-link' property in the Ethernet MAC node, with 5 cells, of the - form <a b c d e> with the following accepted values: - - a: emulated PHY ID, choose any but but unique to the all specified - fixed-links, from 0 to 31 - - b: duplex configuration: 0 for half duplex, 1 for full duplex - - c: link speed in Mbits/sec, accepted values are: 10, 100 and 1000 - - d: pause configuration: 0 for no pause, 1 for pause - - e: asymmetric pause configuration: 0 for no asymmetric pause, 1 for - asymmetric pause - -Examples: - -ethernet@0 { - ... - fixed-link { - speed = <1000>; - full-duplex; - }; - ... -}; - -ethernet@1 { - ... - fixed-link { - speed = <1000>; - pause; - link-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; - }; - ... -}; +This file has moved to ethernet-controller.yaml. diff --git a/Documentation/devicetree/bindings/net/fsl-enetc.txt b/Documentation/devicetree/bindings/net/fsl-enetc.txt index c812e25ae90f..b7034ccbc1bd 100644 --- a/Documentation/devicetree/bindings/net/fsl-enetc.txt +++ b/Documentation/devicetree/bindings/net/fsl-enetc.txt @@ -11,13 +11,15 @@ Required properties: to parent node bindings. - compatible : Should be "fsl,enetc". -1) The ENETC external port is connected to a MDIO configurable phy: +1. The ENETC external port is connected to a MDIO configurable phy + +1.1. Using the local ENETC Port MDIO interface In this case, the ENETC node should include a "mdio" sub-node that in turn should contain the "ethernet-phy" node describing the external phy. Below properties are required, their bindings -already defined in ethernet.txt or phy.txt, under -Documentation/devicetree/bindings/net/*. +already defined in Documentation/devicetree/bindings/net/ethernet.txt or +Documentation/devicetree/bindings/net/phy.txt. Required: @@ -47,12 +49,45 @@ Example: }; }; -2) The ENETC port is an internal port or has a fixed-link external -connection: +1.2. Using the central MDIO PCIe endpoint device + +In this case, the mdio node should be defined as another PCIe +endpoint node, at the same level with the ENETC port nodes. + +Required properties: + +- reg : Specifies PCIe Device Number and Function + Number of the ENETC endpoint device, according + to parent node bindings. +- compatible : Should be "fsl,enetc-mdio". + +The remaining required mdio bus properties are standard, their bindings +already defined in Documentation/devicetree/bindings/net/mdio.txt. + +Example: + + ethernet@0,0 { + compatible = "fsl,enetc"; + reg = <0x000000 0 0 0 0>; + phy-handle = <&sgmii_phy0>; + phy-connection-type = "sgmii"; + }; + + mdio@0,3 { + compatible = "fsl,enetc-mdio"; + reg = <0x000300 0 0 0 0>; + #address-cells = <1>; + #size-cells = <0>; + sgmii_phy0: ethernet-phy@2 { + reg = <0x2>; + }; + }; + +2. The ENETC port is an internal port or has a fixed-link external +connection In this case, the ENETC port node defines a fixed link connection, -as specified by "fixed-link.txt", under -Documentation/devicetree/bindings/net/*. +as specified by Documentation/devicetree/bindings/net/fixed-link.txt. Required: diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt index 2d41fb96ce0a..5b88fae0307d 100644 --- a/Documentation/devicetree/bindings/net/fsl-fec.txt +++ b/Documentation/devicetree/bindings/net/fsl-fec.txt @@ -7,18 +7,6 @@ Required properties: - phy-mode : See ethernet.txt file in the same directory Optional properties: -- phy-reset-gpios : Should specify the gpio for phy reset -- phy-reset-duration : Reset duration in milliseconds. Should present - only if property "phy-reset-gpios" is available. Missing the property - will have the duration be 1 millisecond. Numbers greater than 1000 are - invalid and 1 millisecond will be used instead. -- phy-reset-active-high : If present then the reset sequence using the GPIO - specified in the "phy-reset-gpios" property is reversed (H=reset state, - L=operation state). -- phy-reset-post-delay : Post reset delay in milliseconds. If present then - a delay of phy-reset-post-delay milliseconds will be observed after the - phy-reset-gpios has been toggled. Can be omitted thus no delay is - observed. Delay is in range of 1ms to 1000ms. Other delays are invalid. - phy-supply : regulator that powers the Ethernet PHY. - phy-handle : phandle to the PHY device connected to this device. - fixed-link : Assume a fixed link. See fixed-link.txt in the same directory. @@ -47,11 +35,27 @@ Optional properties: For imx6sx, "int0" handles all 3 queues and ENET_MII. "pps" is for the pulse per second interrupt associated with 1588 precision time protocol(PTP). - Optional subnodes: - mdio : specifies the mdio bus in the FEC, used as a container for phy nodes according to phy.txt in the same directory +Deprecated optional properties: + To avoid these, create a phy node according to phy.txt in the same + directory, and point the fec's "phy-handle" property to it. Then use + the phy's reset binding, again described by phy.txt. +- phy-reset-gpios : Should specify the gpio for phy reset +- phy-reset-duration : Reset duration in milliseconds. Should present + only if property "phy-reset-gpios" is available. Missing the property + will have the duration be 1 millisecond. Numbers greater than 1000 are + invalid and 1 millisecond will be used instead. +- phy-reset-active-high : If present then the reset sequence using the GPIO + specified in the "phy-reset-gpios" property is reversed (H=reset state, + L=operation state). +- phy-reset-post-delay : Post reset delay in milliseconds. If present then + a delay of phy-reset-post-delay milliseconds will be observed after the + phy-reset-gpios has been toggled. Can be omitted thus no delay is + observed. Delay is in range of 1ms to 1000ms. Other delays are invalid. + Example: ethernet@83fec000 { diff --git a/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt b/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt index d1df8a00e1f3..464c0dafc617 100644 --- a/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt +++ b/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt @@ -10,6 +10,7 @@ Required properties: phandle, specifies a reference to the syscon ppe node port, port number connected to the controller channel, recv channel start from channel * number (RX_DESC_NUM) + group, field in the pkg desc, in general, it is the same as the port. - phy-mode: see ethernet.txt [1]. Optional properties: @@ -66,7 +67,7 @@ Example: reg = <0x28b0000 0x10000>; interrupts = <0 413 4>; phy-mode = "mii"; - port-handle = <&ppe 31 0>; + port-handle = <&ppe 31 0 31>; }; ge0: ethernet@2800000 { @@ -74,7 +75,7 @@ Example: reg = <0x2800000 0x10000>; interrupts = <0 402 4>; phy-mode = "sgmii"; - port-handle = <&ppe 0 1>; + port-handle = <&ppe 0 1 0>; phy-handle = <&phy0>; }; @@ -83,6 +84,6 @@ Example: reg = <0x2880000 0x10000>; interrupts = <0 410 4>; phy-mode = "sgmii"; - port-handle = <&ppe 8 2>; + port-handle = <&ppe 8 2 8>; phy-handle = <&phy1>; }; diff --git a/Documentation/devicetree/bindings/net/keystone-netcp.txt b/Documentation/devicetree/bindings/net/keystone-netcp.txt index 6262c2f293b0..24f11e042f8d 100644 --- a/Documentation/devicetree/bindings/net/keystone-netcp.txt +++ b/Documentation/devicetree/bindings/net/keystone-netcp.txt @@ -104,6 +104,23 @@ Required properties: - 10Gb mac<->mac forced mode : 11 ----phy-handle: phandle to PHY device +- cpts: sub-node time synchronization (CPTS) submodule configuration +-- clocks: CPTS reference clock. Should point on cpts-refclk-mux clock. +-- clock-names: should be "cpts" +-- cpts-refclk-mux: multiplexer clock definition sub-node for CPTS reference (RFTCLK) clock +--- #clock-cells: should be 0 +--- clocks: list of CPTS reference (RFTCLK) clock's parents as defined in Data manual +--- ti,mux-tbl: array of multiplexer indexes as defined in Data manual +--- assigned-clocks: should point on cpts-refclk-mux clock +--- assigned-clock-parents: should point on required RFTCLK clock parent to be selected +-- cpts_clock_mult: (optional) Numerator to convert input clock ticks + into nanoseconds +-- cpts_clock_shift: (optional) Denominator to convert input clock ticks into + nanoseconds. + Mult and shift will be calculated basing on CPTS + rftclk frequency if both cpts_clock_shift and + cpts_clock_mult properties are not provided. + Optional properties: - enable-ale: NetCP driver keeps the address learning feature in the ethernet switch module disabled. This attribute is to enable the address @@ -168,6 +185,23 @@ netcp: netcp@2000000 { tx-queue = <648>; tx-channel = <8>; + cpts { + clocks = <&cpts_refclk_mux>; + clock-names = "cpts"; + + cpts_refclk_mux: cpts-refclk-mux { + #clock-cells = <0>; + clocks = <&chipclk12>, <&chipclk13>, + <&timi0>, <&timi1>, + <&tsipclka>, <&tsrefclk>, + <&tsipclkb>; + ti,mux-tbl = <0x0>, <0x1>, <0x2>, + <0x3>, <0x4>, <0x8>, <0xC>; + assigned-clocks = <&cpts_refclk_mux>; + assigned-clock-parents = <&chipclk12>; + }; + }; + interfaces { gbe0: interface-0 { slave-port = <0>; @@ -219,3 +253,13 @@ netcp: netcp@2000000 { }; }; }; + +CPTS board configuration - select external CPTS RFTCLK: + +&tsrefclk{ + clock-frequency = <500000000>; +}; + +&cpts_refclk_mux { + assigned-clock-parents = <&tsrefclk>; +}; diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index 9c5e94482b5f..0b61a90f1592 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -15,8 +15,11 @@ Required properties: Use "atmel,sama5d4-gem" for the GEM IP (10/100) available on Atmel sama5d4 SoCs. Use "cdns,zynq-gem" Xilinx Zynq-7xxx SoC. Use "cdns,zynqmp-gem" for Zynq Ultrascale+ MPSoC. + Use "sifive,fu540-c000-gem" for SiFive FU540-C000 SoC. Or the generic form: "cdns,emac". - reg: Address and length of the register set for the device + For "sifive,fu540-c000-gem", second range is required to specify the + address and length of the registers for GEMGXL Management block. - interrupts: Should contain macb interrupt - phy-mode: See ethernet.txt file in the same directory. - clock-names: Tuple listing input clock names. diff --git a/Documentation/devicetree/bindings/net/marvell-bluetooth.txt b/Documentation/devicetree/bindings/net/marvell-bluetooth.txt new file mode 100644 index 000000000000..0e2842296032 --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-bluetooth.txt @@ -0,0 +1,25 @@ +Marvell Bluetooth Chips +----------------------- + +This documents the binding structure and common properties for serial +attached Marvell Bluetooth devices. The following chips are included in +this binding: + +* Marvell 88W8897 Bluetooth devices + +Required properties: + - compatible: should be: + "mrvl,88w8897" + +Optional properties: +None so far + +Example: + +&serial0 { + compatible = "ns16550a"; + ... + bluetooth { + compatible = "mrvl,88w8897"; + }; +}; diff --git a/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt b/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt index 42cd81090a2c..3f3cfc1d8d4d 100644 --- a/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt +++ b/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt @@ -16,7 +16,7 @@ Required properties: Optional properties: - interrupts: interrupt line number for the SMI error/done interrupt -- clocks: phandle for up to three required clocks for the MDIO instance +- clocks: phandle for up to four required clocks for the MDIO instance The child nodes of the MDIO driver are the individual PHY devices connected to this MDIO bus. They must have a "reg" property given the diff --git a/Documentation/devicetree/bindings/net/mdio.txt b/Documentation/devicetree/bindings/net/mdio.txt index e3e1603f256c..cf8a0105488e 100644 --- a/Documentation/devicetree/bindings/net/mdio.txt +++ b/Documentation/devicetree/bindings/net/mdio.txt @@ -1,37 +1 @@ -Common MDIO bus properties. - -These are generic properties that can apply to any MDIO bus. - -Optional properties: -- reset-gpios: One GPIO that control the RESET lines of all PHYs on that MDIO - bus. -- reset-delay-us: RESET pulse width in microseconds. - -A list of child nodes, one per device on the bus is expected. These -should follow the generic phy.txt, or a device specific binding document. - -The 'reset-delay-us' indicates the RESET signal pulse width in microseconds and -applies to all PHY devices. It must therefore be appropriately determined based -on all PHY requirements (maximum value of all per-PHY RESET pulse widths). - -Example : -This example shows these optional properties, plus other properties -required for the TI Davinci MDIO driver. - - davinci_mdio: ethernet@5c030000 { - compatible = "ti,davinci_mdio"; - reg = <0x5c030000 0x1000>; - #address-cells = <1>; - #size-cells = <0>; - - reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; - reset-delay-us = <2>; - - ethphy0: ethernet-phy@1 { - reg = <1>; - }; - - ethphy1: ethernet-phy@3 { - reg = <3>; - }; - }; +This file has moved to mdio.yaml. diff --git a/Documentation/devicetree/bindings/net/mdio.yaml b/Documentation/devicetree/bindings/net/mdio.yaml new file mode 100644 index 000000000000..5d08d2ffd4eb --- /dev/null +++ b/Documentation/devicetree/bindings/net/mdio.yaml @@ -0,0 +1,74 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/mdio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MDIO Bus Generic Binding + +maintainers: + - Andrew Lunn <andrew@lunn.ch> + - Florian Fainelli <f.fainelli@gmail.com> + - Heiner Kallweit <hkallweit1@gmail.com> + +description: + These are generic properties that can apply to any MDIO bus. Any + MDIO bus must have a list of child nodes, one per device on the + bus. These should follow the generic ethernet-phy.yaml document, or + a device specific binding document. + +properties: + $nodename: + pattern: "^mdio(@.*)?" + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + reset-gpios: + maxItems: 1 + description: + The phandle and specifier for the GPIO that controls the RESET + lines of all PHYs on that MDIO bus. + + reset-delay-us: + description: + RESET pulse width in microseconds. It applies to all PHY devices + and must therefore be appropriately determined based on all PHY + requirements (maximum value of all per-PHY RESET pulse widths). + +patternProperties: + "^ethernet-phy@[0-9a-f]+$": + type: object + + properties: + reg: + minimum: 0 + maximum: 31 + description: + The ID number for the PHY. + + required: + - reg + +examples: + - | + davinci_mdio: mdio@5c030000 { + compatible = "ti,davinci_mdio"; + reg = <0x5c030000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + reset-gpios = <&gpio2 5 1>; + reset-delay-us = <2>; + + ethphy0: ethernet-phy@1 { + reg = <1>; + }; + + ethphy1: ethernet-phy@3 { + reg = <3>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt b/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt index 41a7dcc80f5b..112011c51d5e 100644 --- a/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt +++ b/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt @@ -50,16 +50,33 @@ Required properties: "mediatek,mt7663u-bluetooth": for MT7663U device "mediatek,mt7668u-bluetooth": for MT7668U device - vcc-supply: Main voltage regulator + +If the pin controller on the platform can support both pinmux and GPIO +control such as the most of MediaTek platform. Please use below properties. + - pinctrl-names: Should be "default", "runtime" - pinctrl-0: Should contain UART RXD low when the device is powered up to enter proper bootstrap mode. - pinctrl-1: Should contain UART mode pin ctrl +Else, the pin controller on the platform only can support pinmux control and +the GPIO control still has to rely on the dedicated GPIO controller such as +a legacy MediaTek SoC, MT7621. Please use the below properties. + +- boot-gpios: GPIO same to the pin as UART RXD and used to keep LOW when + the device is powered up to enter proper bootstrap mode when +- pinctrl-names: Should be "default" +- pinctrl-0: Should contain UART mode pin ctrl + Optional properties: - reset-gpios: GPIO used to reset the device whose initial state keeps low, if the GPIO is missing, then board-level design should be guaranteed. +- clocks: Should be the clock specifiers corresponding to the entry in + clock-names property. If the clock is missing, then board-level + design should be guaranteed. +- clock-names: Should contain "osc" entry for the external oscillator. - current-speed: Current baud rate of the device whose defaults to 921600 Example: diff --git a/Documentation/devicetree/bindings/net/mediatek-net.txt b/Documentation/devicetree/bindings/net/mediatek-net.txt index 503f2b9194e2..72d03e07cf7c 100644 --- a/Documentation/devicetree/bindings/net/mediatek-net.txt +++ b/Documentation/devicetree/bindings/net/mediatek-net.txt @@ -11,6 +11,8 @@ Required properties: "mediatek,mt2701-eth": for MT2701 SoC "mediatek,mt7623-eth", "mediatek,mt2701-eth": for MT7623 SoC "mediatek,mt7622-eth": for MT7622 SoC + "mediatek,mt7629-eth": for MT7629 SoC + "ralink,rt5350-eth": for Ralink Rt5350F and MT7628/88 SoC - reg: Address and length of the register set for the device - interrupts: Should contain the three frame engines interrupts in numeric order. These are fe_int0, fe_int1 and fe_int2. @@ -19,14 +21,23 @@ Required properties: "ethif", "esw", "gp2", "gp1" : For MT2701 and MT7623 SoC "ethif", "esw", "gp0", "gp1", "gp2", "sgmii_tx250m", "sgmii_rx250m", "sgmii_cdr_ref", "sgmii_cdr_fb", "sgmii_ck", "eth2pll" : For MT7622 SoC + "ethif", "sgmiitop", "esw", "gp0", "gp1", "gp2", "fe", "sgmii_tx250m", + "sgmii_rx250m", "sgmii_cdr_ref", "sgmii_cdr_fb", "sgmii2_tx250m", + "sgmii2_rx250m", "sgmii2_cdr_ref", "sgmii2_cdr_fb", "sgmii_ck", + "eth2pll" : For MT7629 SoC. - power-domains: phandle to the power domain that the ethernet is part of - resets: Should contain phandles to the ethsys reset signals - reset-names: Should contain the names of reset signal listed in the resets property These are "fe", "gmac" and "ppe" - mediatek,ethsys: phandle to the syscon node that handles the port setup -- mediatek,sgmiisys: phandle to the syscon node that handles the SGMII setup - which is required for those SoCs equipped with SGMII such as MT7622 SoC. +- mediatek,infracfg: phandle to the syscon node that handles the path from + GMAC to PHY variants, which is required for MT7629 SoC. +- mediatek,sgmiisys: a list of phandles to the syscon node that handles the + SGMII setup which is required for those SoCs equipped with SGMII such + as MT7622 and MT7629 SoC. And MT7622 have only one set of SGMII shared + by GMAC1 and GMAC2; MT7629 have two independent sets of SGMII directed + to GMAC1 and GMAC2, respectively. - mediatek,pctl: phandle to the syscon node that handles the ports slew rate and driver current: only for MT2701 and MT7623 SoC diff --git a/Documentation/devicetree/bindings/net/meson-dwmac.txt b/Documentation/devicetree/bindings/net/meson-dwmac.txt deleted file mode 100644 index 1321bb194ed9..000000000000 --- a/Documentation/devicetree/bindings/net/meson-dwmac.txt +++ /dev/null @@ -1,71 +0,0 @@ -* Amlogic Meson DWMAC Ethernet controller - -The device inherits all the properties of the dwmac/stmmac devices -described in the file stmmac.txt in the current directory with the -following changes. - -Required properties on all platforms: - -- compatible: Depending on the platform this should be one of: - - "amlogic,meson6-dwmac" - - "amlogic,meson8b-dwmac" - - "amlogic,meson8m2-dwmac" - - "amlogic,meson-gxbb-dwmac" - - "amlogic,meson-axg-dwmac" - Additionally "snps,dwmac" and any applicable more - detailed version number described in net/stmmac.txt - should be used. - -- reg: The first register range should be the one of the DWMAC - controller. The second range is is for the Amlogic specific - configuration (for example the PRG_ETHERNET register range - on Meson8b and newer) - -Required properties on Meson8b, Meson8m2, GXBB and newer: -- clock-names: Should contain the following: - - "stmmaceth" - see stmmac.txt - - "clkin0" - first parent clock of the internal mux - - "clkin1" - second parent clock of the internal mux - -Optional properties on Meson8b, Meson8m2, GXBB and newer: -- amlogic,tx-delay-ns: The internal RGMII TX clock delay (provided - by this driver) in nanoseconds. Allowed values - are: 0ns, 2ns, 4ns, 6ns. - When phy-mode is set to "rgmii" then the TX - delay should be explicitly configured. When - not configured a fallback of 2ns is used. - When the phy-mode is set to either "rgmii-id" - or "rgmii-txid" the TX clock delay is already - provided by the PHY. In that case this - property should be set to 0ns (which disables - the TX clock delay in the MAC to prevent the - clock from going off because both PHY and MAC - are adding a delay). - Any configuration is ignored when the phy-mode - is set to "rmii". - -Example for Meson6: - - ethmac: ethernet@c9410000 { - compatible = "amlogic,meson6-dwmac", "snps,dwmac"; - reg = <0xc9410000 0x10000 - 0xc1108108 0x4>; - interrupts = <0 8 1>; - interrupt-names = "macirq"; - clocks = <&clk81>; - clock-names = "stmmaceth"; - } - -Example for GXBB: - ethmac: ethernet@c9410000 { - compatible = "amlogic,meson-gxbb-dwmac", "snps,dwmac"; - reg = <0x0 0xc9410000 0x0 0x10000>, - <0x0 0xc8834540 0x0 0x8>; - interrupts = <0 8 1>; - interrupt-names = "macirq"; - clocks = <&clkc CLKID_ETH>, - <&clkc CLKID_FCLK_DIV2>, - <&clkc CLKID_MPLL2>; - clock-names = "stmmaceth", "clkin0", "clkin1"; - phy-mode = "rgmii"; - }; diff --git a/Documentation/devicetree/bindings/net/mscc-ocelot.txt b/Documentation/devicetree/bindings/net/mscc-ocelot.txt index 9e5c17d426ce..3b6290b45ce5 100644 --- a/Documentation/devicetree/bindings/net/mscc-ocelot.txt +++ b/Documentation/devicetree/bindings/net/mscc-ocelot.txt @@ -12,13 +12,15 @@ Required properties: - "sys" - "rew" - "qs" + - "ptp" (optional due to backward compatibility) - "qsys" - "ana" - "portX" with X from 0 to the number of last port index available on that switch -- interrupts: Should contain the switch interrupts for frame extraction and - frame injection -- interrupt-names: should contain the interrupt names: "xtr", "inj" +- interrupts: Should contain the switch interrupts for frame extraction, + frame injection and PTP ready. +- interrupt-names: should contain the interrupt names: "xtr", "inj". Can contain + "ptp_rdy" which is optional due to backward compatibility. - ethernet-ports: A container for child nodes representing switch ports. The ethernet-ports container has the following properties @@ -44,6 +46,7 @@ Example: reg = <0x1010000 0x10000>, <0x1030000 0x10000>, <0x1080000 0x100>, + <0x10e0000 0x10000>, <0x11e0000 0x100>, <0x11f0000 0x100>, <0x1200000 0x100>, @@ -57,11 +60,12 @@ Example: <0x1280000 0x100>, <0x1800000 0x80000>, <0x1880000 0x10000>; - reg-names = "sys", "rew", "qs", "port0", "port1", "port2", - "port3", "port4", "port5", "port6", "port7", - "port8", "port9", "port10", "qsys", "ana"; - interrupts = <21 22>; - interrupt-names = "xtr", "inj"; + reg-names = "sys", "rew", "qs", "ptp", "port0", "port1", + "port2", "port3", "port4", "port5", "port6", + "port7", "port8", "port9", "port10", "qsys", + "ana"; + interrupts = <18 21 22>; + interrupt-names = "ptp_rdy", "xtr", "inj"; ethernet-ports { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt index 9b9e5b1765dd..2399ee60caed 100644 --- a/Documentation/devicetree/bindings/net/phy.txt +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -1,79 +1 @@ -PHY nodes - -Required properties: - - - interrupts : interrupt specifier for the sole interrupt. - - reg : The ID number for the phy, usually a small integer - -Optional Properties: - -- compatible: Compatible list, may contain - "ethernet-phy-ieee802.3-c22" or "ethernet-phy-ieee802.3-c45" for - PHYs that implement IEEE802.3 clause 22 or IEEE802.3 clause 45 - specifications. If neither of these are specified, the default is to - assume clause 22. - - If the PHY reports an incorrect ID (or none at all) then the - "compatible" list may contain an entry with the correct PHY ID in the - form: "ethernet-phy-idAAAA.BBBB" where - AAAA - The value of the 16 bit Phy Identifier 1 register as - 4 hex digits. This is the chip vendor OUI bits 3:18 - BBBB - The value of the 16 bit Phy Identifier 2 register as - 4 hex digits. This is the chip vendor OUI bits 19:24, - followed by 10 bits of a vendor specific ID. - - The compatible list should not contain other values than those - listed here. - -- max-speed: Maximum PHY supported speed (10, 100, 1000...) - -- broken-turn-around: If set, indicates the PHY device does not correctly - release the turn around line low at the end of a MDIO transaction. - -- enet-phy-lane-swap: If set, indicates the PHY will swap the TX/RX lanes to - compensate for the board being designed with the lanes swapped. - -- enet-phy-lane-no-swap: If set, indicates that PHY will disable swap of the - TX/RX lanes. This property allows the PHY to work correcly after e.g. wrong - bootstrap configuration caused by issues in PCB layout design. - -- eee-broken-100tx: -- eee-broken-1000t: -- eee-broken-10gt: -- eee-broken-1000kx: -- eee-broken-10gkx4: -- eee-broken-10gkr: - Mark the corresponding energy efficient ethernet mode as broken and - request the ethernet to stop advertising it. - -- phy-is-integrated: If set, indicates that the PHY is integrated into the same - physical package as the Ethernet MAC. If needed, muxers should be configured - to ensure the integrated PHY is used. The absence of this property indicates - the muxers should be configured so that the external PHY is used. - -- resets: The reset-controller phandle and specifier for the PHY reset signal. - -- reset-names: Must be "phy" for the PHY reset signal. - -- reset-gpios: The GPIO phandle and specifier for the PHY reset signal. - -- reset-assert-us: Delay after the reset was asserted in microseconds. - If this property is missing the delay will be skipped. - -- reset-deassert-us: Delay after the reset was deasserted in microseconds. - If this property is missing the delay will be skipped. - -Example: - -ethernet-phy@0 { - compatible = "ethernet-phy-id0141.0e90", "ethernet-phy-ieee802.3-c22"; - interrupt-parent = <&PIC>; - interrupts = <35 IRQ_TYPE_EDGE_RISING>; - reg = <0>; - - resets = <&rst 8>; - reset-names = "phy"; - reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; - reset-assert-us = <1000>; - reset-deassert-us = <2000>; -}; +This file has moved to ethernet-phy.yaml. diff --git a/Documentation/devicetree/bindings/net/qca,ar71xx.txt b/Documentation/devicetree/bindings/net/qca,ar71xx.txt new file mode 100644 index 000000000000..2a33e71ba72b --- /dev/null +++ b/Documentation/devicetree/bindings/net/qca,ar71xx.txt @@ -0,0 +1,45 @@ +Required properties: +- compatible: Should be "qca,<soc>-eth". Currently support compatibles are: + qca,ar7100-eth - Atheros AR7100 + qca,ar7240-eth - Atheros AR7240 + qca,ar7241-eth - Atheros AR7241 + qca,ar7242-eth - Atheros AR7242 + qca,ar9130-eth - Atheros AR9130 + qca,ar9330-eth - Atheros AR9330 + qca,ar9340-eth - Atheros AR9340 + qca,qca9530-eth - Qualcomm Atheros QCA9530 + qca,qca9550-eth - Qualcomm Atheros QCA9550 + qca,qca9560-eth - Qualcomm Atheros QCA9560 + +- reg : Address and length of the register set for the device +- interrupts : Should contain eth interrupt +- phy-mode : See ethernet.txt file in the same directory +- clocks: the clock used by the core +- clock-names: the names of the clock listed in the clocks property. These are + "eth" and "mdio". +- resets: Should contain phandles to the reset signals +- reset-names: Should contain the names of reset signal listed in the resets + property. These are "mac" and "mdio" + +Optional properties: +- phy-handle : phandle to the PHY device connected to this device. +- fixed-link : Assume a fixed link. See fixed-link.txt in the same directory. + Use instead of phy-handle. + +Optional subnodes: +- mdio : specifies the mdio bus, used as a container for phy nodes + according to phy.txt in the same directory + +Example: + +ethernet@1a000000 { + compatible = "qca,ar9330-eth"; + reg = <0x1a000000 0x200>; + interrupts = <5>; + resets = <&rst 13>, <&rst 23>; + reset-names = "mac", "mdio"; + clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_MDIO>; + clock-names = "eth", "mdio"; + + phy-mode = "gmii"; +}; diff --git a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt index 7ef6118abd3d..68b67d9db63a 100644 --- a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt +++ b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt @@ -17,6 +17,7 @@ Optional properties for compatible string qcom,qca6174-bt: - enable-gpios: gpio specifier used to enable chip - clocks: clock provided to the controller (SUSCLK_32KHZ) + - firmware-name: specify the name of nvm firmware to load Required properties for compatible string qcom,wcn399x-bt: @@ -28,6 +29,7 @@ Required properties for compatible string qcom,wcn399x-bt: Optional properties for compatible string qcom,wcn399x-bt: - max-speed: see Documentation/devicetree/bindings/serial/slave-device.txt + - firmware-name: specify the name of nvm firmware to load Examples: @@ -40,6 +42,7 @@ serial@7570000 { enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>; clocks = <&divclk4>; + firmware-name = "nvm_00440302.bin"; }; }; @@ -52,5 +55,6 @@ serial@898000 { vddrf-supply = <&vreg_l17a_1p3>; vddch0-supply = <&vreg_l25a_3p3>; max-speed = <3200000>; + firmware-name = "crnv21.bin"; }; }; diff --git a/Documentation/devicetree/bindings/net/snps,dwmac.yaml b/Documentation/devicetree/bindings/net/snps,dwmac.yaml new file mode 100644 index 000000000000..ebe4537a7cce --- /dev/null +++ b/Documentation/devicetree/bindings/net/snps,dwmac.yaml @@ -0,0 +1,425 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/snps,dwmac.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Synopsys DesignWare MAC Device Tree Bindings + +maintainers: + - Alexandre Torgue <alexandre.torgue@st.com> + - Giuseppe Cavallaro <peppe.cavallaro@st.com> + - Jose Abreu <joabreu@synopsys.com> + +# Select every compatible, including the deprecated ones. This way, we +# will be able to report a warning when we have that compatible, since +# we will validate the node thanks to the select, but won't report it +# as a valid value in the compatible property description +select: + properties: + compatible: + contains: + enum: + - snps,dwmac + - snps,dwmac-3.50a + - snps,dwmac-3.610 + - snps,dwmac-3.70a + - snps,dwmac-3.710 + - snps,dwmac-4.00 + - snps,dwmac-4.10a + - snps,dwxgmac + - snps,dwxgmac-2.10 + + # Deprecated + - st,spear600-gmac + + required: + - compatible + +properties: + + # We need to include all the compatibles from schemas that will + # include that schemas, otherwise compatible won't validate for + # those. + compatible: + contains: + enum: + - allwinner,sun7i-a20-gmac + - allwinner,sun8i-a83t-emac + - allwinner,sun8i-h3-emac + - allwinner,sun8i-r40-emac + - allwinner,sun8i-v3s-emac + - allwinner,sun50i-a64-emac + - amlogic,meson6-dwmac + - amlogic,meson8b-dwmac + - amlogic,meson8m2-dwmac + - amlogic,meson-gxbb-dwmac + - amlogic,meson-axg-dwmac + - snps,dwmac + - snps,dwmac-3.50a + - snps,dwmac-3.610 + - snps,dwmac-3.70a + - snps,dwmac-3.710 + - snps,dwmac-4.00 + - snps,dwmac-4.10a + - snps,dwxgmac + - snps,dwxgmac-2.10 + + reg: + minItems: 1 + maxItems: 2 + + interrupts: + minItems: 1 + maxItems: 3 + items: + - description: Combined signal for various interrupt events + - description: The interrupt to manage the remote wake-up packet detection + - description: The interrupt that occurs when Rx exits the LPI state + + interrupt-names: + minItems: 1 + maxItems: 3 + items: + - const: macirq + - const: eth_wake_irq + - const: eth_lpi + + clocks: + minItems: 1 + maxItems: 3 + items: + - description: GMAC main clock + - description: Peripheral registers interface clock + - description: + PTP reference clock. This clock is used for programming the + Timestamp Addend Register. If not passed then the system + clock will be used and this is fine on some platforms. + + clock-names: + additionalItems: true + contains: + enum: + - stmmaceth + - pclk + - ptp_ref + + resets: + maxItems: 1 + description: + MAC Reset signal. + + reset-names: + const: stmmaceth + + mac-mode: + maxItems: 1 + description: + The property is identical to 'phy-mode', and assumes that there is mode + converter in-between the MAC & PHY (e.g. GMII-to-RGMII). This converter + can be passive (no SW requirement), and requires that the MAC operate + in a different mode than the PHY in order to function. + + snps,axi-config: + $ref: /schemas/types.yaml#definitions/phandle + description: + AXI BUS Mode parameters. Phandle to a node that can contain the + following properties + * snps,lpi_en, enable Low Power Interface + * snps,xit_frm, unlock on WoL + * snps,wr_osr_lmt, max write outstanding req. limit + * snps,rd_osr_lmt, max read outstanding req. limit + * snps,kbbe, do not cross 1KiB boundary. + * snps,blen, this is a vector of supported burst length. + * snps,fb, fixed-burst + * snps,mb, mixed-burst + * snps,rb, rebuild INCRx Burst + + snps,mtl-rx-config: + $ref: /schemas/types.yaml#definitions/phandle + description: + Multiple RX Queues parameters. Phandle to a node that can + contain the following properties + * snps,rx-queues-to-use, number of RX queues to be used in the + driver + * Choose one of these RX scheduling algorithms + * snps,rx-sched-sp, Strict priority + * snps,rx-sched-wsp, Weighted Strict priority + * For each RX queue + * Choose one of these modes + * snps,dcb-algorithm, Queue to be enabled as DCB + * snps,avb-algorithm, Queue to be enabled as AVB + * snps,map-to-dma-channel, Channel to map + * Specifiy specific packet routing + * snps,route-avcp, AV Untagged Control packets + * snps,route-ptp, PTP Packets + * snps,route-dcbcp, DCB Control Packets + * snps,route-up, Untagged Packets + * snps,route-multi-broad, Multicast & Broadcast Packets + * snps,priority, RX queue priority (Range 0x0 to 0xF) + + snps,mtl-tx-config: + $ref: /schemas/types.yaml#definitions/phandle + description: + Multiple TX Queues parameters. Phandle to a node that can + contain the following properties + * snps,tx-queues-to-use, number of TX queues to be used in the + driver + * Choose one of these TX scheduling algorithms + * snps,tx-sched-wrr, Weighted Round Robin + * snps,tx-sched-wfq, Weighted Fair Queuing + * snps,tx-sched-dwrr, Deficit Weighted Round Robin + * snps,tx-sched-sp, Strict priority + * For each TX queue + * snps,weight, TX queue weight (if using a DCB weight + algorithm) + * Choose one of these modes + * snps,dcb-algorithm, TX queue will be working in DCB + * snps,avb-algorithm, TX queue will be working in AVB + [Attention] Queue 0 is reserved for legacy traffic + and so no AVB is available in this queue. + * Configure Credit Base Shaper (if AVB Mode selected) + * snps,send_slope, enable Low Power Interface + * snps,idle_slope, unlock on WoL + * snps,high_credit, max write outstanding req. limit + * snps,low_credit, max read outstanding req. limit + * snps,priority, TX queue priority (Range 0x0 to 0xF) + + snps,reset-gpio: + deprecated: true + maxItems: 1 + description: + PHY Reset GPIO + + snps,reset-active-low: + deprecated: true + $ref: /schemas/types.yaml#definitions/flag + description: + Indicates that the PHY Reset is active low + + snps,reset-delays-us: + deprecated: true + allOf: + - $ref: /schemas/types.yaml#definitions/uint32-array + - minItems: 3 + maxItems: 3 + description: + Triplet of delays. The 1st cell is reset pre-delay in micro + seconds. The 2nd cell is reset pulse in micro seconds. The 3rd + cell is reset post-delay in micro seconds. + + snps,aal: + $ref: /schemas/types.yaml#definitions/flag + description: + Use Address-Aligned Beats + + snps,fixed-burst: + $ref: /schemas/types.yaml#definitions/flag + description: + Program the DMA to use the fixed burst mode + + snps,mixed-burst: + $ref: /schemas/types.yaml#definitions/flag + description: + Program the DMA to use the mixed burst mode + + snps,force_thresh_dma_mode: + $ref: /schemas/types.yaml#definitions/flag + description: + Force DMA to use the threshold mode for both tx and rx + + snps,force_sf_dma_mode: + $ref: /schemas/types.yaml#definitions/flag + description: + Force DMA to use the Store and Forward mode for both tx and + rx. This flag is ignored if force_thresh_dma_mode is set. + + snps,en-tx-lpi-clockgating: + $ref: /schemas/types.yaml#definitions/flag + description: + Enable gating of the MAC TX clock during TX low-power mode + + snps,multicast-filter-bins: + $ref: /schemas/types.yaml#definitions/uint32 + description: + Number of multicast filter hash bins supported by this device + instance + + snps,perfect-filter-entries: + $ref: /schemas/types.yaml#definitions/uint32 + description: + Number of perfect filter entries supported by this device + instance + + snps,ps-speed: + $ref: /schemas/types.yaml#definitions/uint32 + description: + Port selection speed that can be passed to the core when PCS + is supported. For example, this is used in case of SGMII and + MAC2MAC connection. + + mdio: + type: object + description: + Creates and registers an MDIO bus. + + properties: + compatible: + const: snps,dwmac-mdio + + required: + - compatible + +required: + - compatible + - reg + - interrupts + - interrupt-names + - phy-mode + +dependencies: + snps,reset-active-low: ["snps,reset-gpio"] + snps,reset-delay-us: ["snps,reset-gpio"] + +allOf: + - $ref: "ethernet-controller.yaml#" + - if: + properties: + compatible: + contains: + enum: + - allwinner,sun7i-a20-gmac + - allwinner,sun8i-a83t-emac + - allwinner,sun8i-h3-emac + - allwinner,sun8i-r40-emac + - allwinner,sun8i-v3s-emac + - allwinner,sun50i-a64-emac + - snps,dwxgmac + - snps,dwxgmac-2.10 + - st,spear600-gmac + + then: + properties: + snps,pbl: + allOf: + - $ref: /schemas/types.yaml#definitions/uint32 + - enum: [2, 4, 8] + description: + Programmable Burst Length (tx and rx) + + snps,txpbl: + allOf: + - $ref: /schemas/types.yaml#definitions/uint32 + - enum: [2, 4, 8] + description: + Tx Programmable Burst Length. If set, DMA tx will use this + value rather than snps,pbl. + + snps,rxpbl: + allOf: + - $ref: /schemas/types.yaml#definitions/uint32 + - enum: [2, 4, 8] + description: + Rx Programmable Burst Length. If set, DMA rx will use this + value rather than snps,pbl. + + snps,no-pbl-x8: + $ref: /schemas/types.yaml#definitions/flag + description: + Don\'t multiply the pbl/txpbl/rxpbl values by 8. For core + rev < 3.50, don\'t multiply the values by 4. + + - if: + properties: + compatible: + contains: + enum: + - allwinner,sun7i-a20-gmac + - allwinner,sun8i-a83t-emac + - allwinner,sun8i-h3-emac + - allwinner,sun8i-r40-emac + - allwinner,sun8i-v3s-emac + - allwinner,sun50i-a64-emac + - snps,dwmac-4.00 + - snps,dwmac-4.10a + - snps,dwxgmac + - snps,dwxgmac-2.10 + - st,spear600-gmac + + then: + snps,tso: + $ref: /schemas/types.yaml#definitions/flag + description: + Enables the TSO feature otherwise it will be managed by + MAC HW capability register. + +examples: + - | + stmmac_axi_setup: stmmac-axi-config { + snps,wr_osr_lmt = <0xf>; + snps,rd_osr_lmt = <0xf>; + snps,blen = <256 128 64 32 0 0 0>; + }; + + mtl_rx_setup: rx-queues-config { + snps,rx-queues-to-use = <1>; + snps,rx-sched-sp; + queue0 { + snps,dcb-algorithm; + snps,map-to-dma-channel = <0x0>; + snps,priority = <0x0>; + }; + }; + + mtl_tx_setup: tx-queues-config { + snps,tx-queues-to-use = <2>; + snps,tx-sched-wrr; + queue0 { + snps,weight = <0x10>; + snps,dcb-algorithm; + snps,priority = <0x0>; + }; + + queue1 { + snps,avb-algorithm; + snps,send_slope = <0x1000>; + snps,idle_slope = <0x1000>; + snps,high_credit = <0x3E800>; + snps,low_credit = <0xFFC18000>; + snps,priority = <0x1>; + }; + }; + + gmac0: ethernet@e0800000 { + compatible = "snps,dwxgmac-2.10", "snps,dwxgmac"; + reg = <0xe0800000 0x8000>; + interrupt-parent = <&vic1>; + interrupts = <24 23 22>; + interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; + mac-address = [000000000000]; /* Filled in by U-Boot */ + max-frame-size = <3800>; + phy-mode = "gmii"; + snps,multicast-filter-bins = <256>; + snps,perfect-filter-entries = <128>; + rx-fifo-depth = <16384>; + tx-fifo-depth = <16384>; + clocks = <&clock>; + clock-names = "stmmaceth"; + snps,axi-config = <&stmmac_axi_setup>; + snps,mtl-rx-config = <&mtl_rx_setup>; + snps,mtl-tx-config = <&mtl_tx_setup>; + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + phy1: ethernet-phy@0 { + reg = <0>; + }; + }; + }; + +# FIXME: We should set it, but it would report all the generic +# properties as additional properties. +# additionalProperties: false + +... diff --git a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt index 17d6819669c8..612a8e8abc88 100644 --- a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt +++ b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt @@ -6,11 +6,17 @@ present in Documentation/devicetree/bindings/net/stmmac.txt. The device node has additional properties: Required properties: - - compatible : Should contain "altr,socfpga-stmmac" along with - "snps,dwmac" and any applicable more detailed + - compatible : For Cyclone5/Arria5 SoCs it should contain + "altr,socfpga-stmmac". For Arria10/Agilex/Stratix10 SoCs + "altr,socfpga-stmmac-a10-s10". + Along with "snps,dwmac" and any applicable more detailed designware version numbers documented in stmmac.txt - altr,sysmgr-syscon : Should be the phandle to the system manager node that encompasses the glue register, the register offset, and the register shift. + On Cyclone5/Arria5, the register shift represents the PHY mode bits, while + on the Arria10/Stratix10/Agilex platforms, the register shift represents + bit for each emac to enable/disable signals from the FPGA fabric to the + EMAC modules. - altr,f2h_ptp_ref_clk use f2h_ptp_ref_clk instead of default eosc1 clock for ptp ref clk. This affects all emacs as the clock is common. diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index cb694062afff..7d48782767cb 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -1,178 +1 @@ -* STMicroelectronics 10/100/1000/2500/10000 Ethernet (GMAC/XGMAC) - -Required properties: -- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac" or - "snps,dwxgmac-<ip_version>", "snps,dwxgmac". - For backwards compatibility: "st,spear600-gmac" is also supported. -- reg: Address and length of the register set for the device -- interrupts: Should contain the STMMAC interrupts -- interrupt-names: Should contain a list of interrupt names corresponding to - the interrupts in the interrupts property, if available. - Valid interrupt names are: - - "macirq" (combined signal for various interrupt events) - - "eth_wake_irq" (the interrupt to manage the remote wake-up packet detection) - - "eth_lpi" (the interrupt that occurs when Rx exits the LPI state) -- phy-mode: See ethernet.txt file in the same directory. -- snps,reset-gpio gpio number for phy reset. -- snps,reset-active-low boolean flag to indicate if phy reset is active low. -- snps,reset-delays-us is triplet of delays - The 1st cell is reset pre-delay in micro seconds. - The 2nd cell is reset pulse in micro seconds. - The 3rd cell is reset post-delay in micro seconds. - -Optional properties: -- resets: Should contain a phandle to the STMMAC reset signal, if any -- reset-names: Should contain the reset signal name "stmmaceth", if a - reset phandle is given -- max-frame-size: See ethernet.txt file in the same directory -- clocks: If present, the first clock should be the GMAC main clock and - the second clock should be peripheral's register interface clock. Further - clocks may be specified in derived bindings. -- clock-names: One name for each entry in the clocks property, the - first one should be "stmmaceth" and the second one should be "pclk". -- ptp_ref: this is the PTP reference clock; in case of the PTP is available - this clock is used for programming the Timestamp Addend Register. If not - passed then the system clock will be used and this is fine on some - platforms. -- tx-fifo-depth: See ethernet.txt file in the same directory -- rx-fifo-depth: See ethernet.txt file in the same directory -- snps,pbl Programmable Burst Length (tx and rx) -- snps,txpbl Tx Programmable Burst Length. Only for GMAC and newer. - If set, DMA tx will use this value rather than snps,pbl. -- snps,rxpbl Rx Programmable Burst Length. Only for GMAC and newer. - If set, DMA rx will use this value rather than snps,pbl. -- snps,no-pbl-x8 Don't multiply the pbl/txpbl/rxpbl values by 8. - For core rev < 3.50, don't multiply the values by 4. -- snps,aal Address-Aligned Beats -- snps,fixed-burst Program the DMA to use the fixed burst mode -- snps,mixed-burst Program the DMA to use the mixed burst mode -- snps,force_thresh_dma_mode Force DMA to use the threshold mode for - both tx and rx -- snps,force_sf_dma_mode Force DMA to use the Store and Forward - mode for both tx and rx. This flag is - ignored if force_thresh_dma_mode is set. -- snps,en-tx-lpi-clockgating Enable gating of the MAC TX clock during - TX low-power mode -- snps,multicast-filter-bins: Number of multicast filter hash bins - supported by this device instance -- snps,perfect-filter-entries: Number of perfect filter entries supported - by this device instance -- snps,ps-speed: port selection speed that can be passed to the core when - PCS is supported. For example, this is used in case of SGMII - and MAC2MAC connection. -- snps,tso: this enables the TSO feature otherwise it will be managed by - MAC HW capability register. Only for GMAC4 and newer. -- AXI BUS Mode parameters: below the list of all the parameters to program the - AXI register inside the DMA module: - - snps,lpi_en: enable Low Power Interface - - snps,xit_frm: unlock on WoL - - snps,wr_osr_lmt: max write outstanding req. limit - - snps,rd_osr_lmt: max read outstanding req. limit - - snps,kbbe: do not cross 1KiB boundary. - - snps,blen: this is a vector of supported burst length. - - snps,fb: fixed-burst - - snps,mb: mixed-burst - - snps,rb: rebuild INCRx Burst -- mdio: with compatible = "snps,dwmac-mdio", create and register mdio bus. -- Multiple RX Queues parameters: below the list of all the parameters to - configure the multiple RX queues: - - snps,rx-queues-to-use: number of RX queues to be used in the driver - - Choose one of these RX scheduling algorithms: - - snps,rx-sched-sp: Strict priority - - snps,rx-sched-wsp: Weighted Strict priority - - For each RX queue - - Choose one of these modes: - - snps,dcb-algorithm: Queue to be enabled as DCB - - snps,avb-algorithm: Queue to be enabled as AVB - - snps,map-to-dma-channel: Channel to map - - Specifiy specific packet routing: - - snps,route-avcp: AV Untagged Control packets - - snps,route-ptp: PTP Packets - - snps,route-dcbcp: DCB Control Packets - - snps,route-up: Untagged Packets - - snps,route-multi-broad: Multicast & Broadcast Packets - - snps,priority: RX queue priority (Range: 0x0 to 0xF) -- Multiple TX Queues parameters: below the list of all the parameters to - configure the multiple TX queues: - - snps,tx-queues-to-use: number of TX queues to be used in the driver - - Choose one of these TX scheduling algorithms: - - snps,tx-sched-wrr: Weighted Round Robin - - snps,tx-sched-wfq: Weighted Fair Queuing - - snps,tx-sched-dwrr: Deficit Weighted Round Robin - - snps,tx-sched-sp: Strict priority - - For each TX queue - - snps,weight: TX queue weight (if using a DCB weight algorithm) - - Choose one of these modes: - - snps,dcb-algorithm: TX queue will be working in DCB - - snps,avb-algorithm: TX queue will be working in AVB - [Attention] Queue 0 is reserved for legacy traffic - and so no AVB is available in this queue. - - Configure Credit Base Shaper (if AVB Mode selected): - - snps,send_slope: enable Low Power Interface - - snps,idle_slope: unlock on WoL - - snps,high_credit: max write outstanding req. limit - - snps,low_credit: max read outstanding req. limit - - snps,priority: TX queue priority (Range: 0x0 to 0xF) -Examples: - - stmmac_axi_setup: stmmac-axi-config { - snps,wr_osr_lmt = <0xf>; - snps,rd_osr_lmt = <0xf>; - snps,blen = <256 128 64 32 0 0 0>; - }; - - mtl_rx_setup: rx-queues-config { - snps,rx-queues-to-use = <1>; - snps,rx-sched-sp; - queue0 { - snps,dcb-algorithm; - snps,map-to-dma-channel = <0x0>; - snps,priority = <0x0>; - }; - }; - - mtl_tx_setup: tx-queues-config { - snps,tx-queues-to-use = <2>; - snps,tx-sched-wrr; - queue0 { - snps,weight = <0x10>; - snps,dcb-algorithm; - snps,priority = <0x0>; - }; - - queue1 { - snps,avb-algorithm; - snps,send_slope = <0x1000>; - snps,idle_slope = <0x1000>; - snps,high_credit = <0x3E800>; - snps,low_credit = <0xFFC18000>; - snps,priority = <0x1>; - }; - }; - - gmac0: ethernet@e0800000 { - compatible = "st,spear600-gmac"; - reg = <0xe0800000 0x8000>; - interrupt-parent = <&vic1>; - interrupts = <24 23 22>; - interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; - mac-address = [000000000000]; /* Filled in by U-Boot */ - max-frame-size = <3800>; - phy-mode = "gmii"; - snps,multicast-filter-bins = <256>; - snps,perfect-filter-entries = <128>; - rx-fifo-depth = <16384>; - tx-fifo-depth = <16384>; - clocks = <&clock>; - clock-names = "stmmaceth"; - snps,axi-config = <&stmmac_axi_setup>; - mdio0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "snps,dwmac-mdio"; - phy1: ethernet-phy@0 { - }; - }; - snps,mtl-rx-config = <&mtl_rx_setup>; - snps,mtl-tx-config = <&mtl_tx_setup>; - }; +This file has moved to snps,dwmac.yaml. diff --git a/Documentation/devicetree/bindings/net/ti,dp83867.txt b/Documentation/devicetree/bindings/net/ti,dp83867.txt index 9ef9338aaee1..388ff48f53ae 100644 --- a/Documentation/devicetree/bindings/net/ti,dp83867.txt +++ b/Documentation/devicetree/bindings/net/ti,dp83867.txt @@ -11,6 +11,14 @@ Required properties: - ti,fifo-depth - Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h for applicable values +Note: If the interface type is PHY_INTERFACE_MODE_RGMII the TX/RX clock delays + will be left at their default values, as set by the PHY's pin strapping. + The default strapping will use a delay of 2.00 ns. Thus + PHY_INTERFACE_MODE_RGMII, by default, does not behave as RGMII with no + internal delay, but as PHY_INTERFACE_MODE_RGMII_ID. The device tree + should use "rgmii-id" if internal delays are desired as this may be + changed in future to cause "rgmii" mode to disable delays. + Optional property: - ti,min-output-impedance - MAC Interface Impedance control to set the programmable output impedance to @@ -25,8 +33,14 @@ Optional property: software needs to take when this pin is strapped in these modes. See data manual for details. - - ti,clk-output-sel - Muxing option for CLK_OUT pin - see dt-bindings/net/ti-dp83867.h - for applicable values. + - ti,clk-output-sel - Muxing option for CLK_OUT pin. See dt-bindings/net/ti-dp83867.h + for applicable values. The CLK_OUT pin can also + be disabled by this property. When omitted, the + PHY's default will be left as is. + - ti,sgmii-ref-clock-output-enable - This denotes which + SGMII configuration is used (4 or 6-wire modes). + Some MACs work with differential SGMII clock. + See data manual for details. Note: ti,min-output-impedance and ti,max-output-impedance are mutually exclusive. When both properties are present ti,max-output-impedance diff --git a/Documentation/devicetree/bindings/net/wiznet,w5x00.txt b/Documentation/devicetree/bindings/net/wiznet,w5x00.txt new file mode 100644 index 000000000000..e9665798c4be --- /dev/null +++ b/Documentation/devicetree/bindings/net/wiznet,w5x00.txt @@ -0,0 +1,50 @@ +* Wiznet w5x00 + +This is a standalone 10/100 MBit Ethernet controller with SPI interface. + +For each device connected to a SPI bus, define a child node within +the SPI master node. + +Required properties: +- compatible: Should be one of the following strings: + "wiznet,w5100" + "wiznet,w5200" + "wiznet,w5500" +- reg: Specify the SPI chip select the chip is wired to. +- interrupts: Specify the interrupt index within the interrupt controller (referred + to above in interrupt-parent) and interrupt type. w5x00 natively + generates falling edge interrupts, however, additional board logic + might invert the signal. +- pinctrl-names: List of assigned state names, see pinctrl binding documentation. +- pinctrl-0: List of phandles to configure the GPIO pin used as interrupt line, + see also generic and your platform specific pinctrl binding + documentation. + +Optional properties: +- spi-max-frequency: Maximum frequency of the SPI bus when accessing the w5500. + According to the w5500 datasheet, the chip allows a maximum of 80 MHz, however, + board designs may need to limit this value. +- local-mac-address: See ethernet.txt in the same directory. + + +Example (for Raspberry Pi with pin control stuff for GPIO irq): + +&spi { + ethernet@0: w5500@0 { + compatible = "wiznet,w5500"; + reg = <0>; + pinctrl-names = "default"; + pinctrl-0 = <ð1_pins>; + interrupt-parent = <&gpio>; + interrupts = <25 IRQ_TYPE_EDGE_FALLING>; + spi-max-frequency = <30000000>; + }; +}; + +&gpio { + eth1_pins: eth1_pins { + brcm,pins = <25>; + brcm,function = <0>; /* in */ + brcm,pull = <0>; /* none */ + }; +}; diff --git a/Documentation/devicetree/bindings/net/xilinx_axienet.txt b/Documentation/devicetree/bindings/net/xilinx_axienet.txt index 38f9ec076743..7360617cdedb 100644 --- a/Documentation/devicetree/bindings/net/xilinx_axienet.txt +++ b/Documentation/devicetree/bindings/net/xilinx_axienet.txt @@ -17,8 +17,15 @@ For more details about mdio please refer phy.txt file in the same directory. Required properties: - compatible : Must be one of "xlnx,axi-ethernet-1.00.a", "xlnx,axi-ethernet-1.01.a", "xlnx,axi-ethernet-2.01.a" -- reg : Address and length of the IO space. -- interrupts : Should be a list of two interrupt, TX and RX. +- reg : Address and length of the IO space, as well as the address + and length of the AXI DMA controller IO space, unless + axistream-connected is specified, in which case the reg + attribute of the node referenced by it is used. +- interrupts : Should be a list of 2 or 3 interrupts: TX DMA, RX DMA, + and optionally Ethernet core. If axistream-connected is + specified, the TX/RX DMA interrupts should be on that node + instead, and only the Ethernet core interrupt is optionally + specified here. - phy-handle : Should point to the external phy device. See ethernet.txt file in the same directory. - xlnx,rxmem : Set to allocated memory buffer for Rx/Tx in the hardware @@ -31,15 +38,29 @@ Optional properties: 1 to enable partial TX checksum offload, 2 to enable full TX checksum offload - xlnx,rxcsum : Same values as xlnx,txcsum but for RX checksum offload +- clocks : AXI bus clock for the device. Refer to common clock bindings. + Used to calculate MDIO clock divisor. If not specified, it is + auto-detected from the CPU clock (but only on platforms where + this is possible). New device trees should specify this - the + auto detection is only for backward compatibility. +- axistream-connected: Reference to another node which contains the resources + for the AXI DMA controller used by this device. + If this is specified, the DMA-related resources from that + device (DMA registers and DMA TX/RX interrupts) rather + than this one will be used. + - mdio : Child node for MDIO bus. Must be defined if PHY access is + required through the core's MDIO interface (i.e. always, + unless the PHY is accessed through a different bus). Example: axi_ethernet_eth: ethernet@40c00000 { compatible = "xlnx,axi-ethernet-1.00.a"; device_type = "network"; interrupt-parent = <µblaze_0_axi_intc>; - interrupts = <2 0>; + interrupts = <2 0 1>; + clocks = <&axi_clk>; phy-mode = "mii"; - reg = <0x40c00000 0x40000>; + reg = <0x40c00000 0x40000 0x50c00000 0x40000>; xlnx,rxcsum = <0x2>; xlnx,rxmem = <0x800>; xlnx,txcsum = <0x2>; diff --git a/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml b/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml new file mode 100644 index 000000000000..1084e9d2917d --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml @@ -0,0 +1,51 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/nvmem/allwinner,sun4i-a10-sid.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 Security ID Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +allOf: + - $ref: "nvmem.yaml#" + +properties: + compatible: + enum: + - allwinner,sun4i-a10-sid + - allwinner,sun7i-a20-sid + - allwinner,sun8i-a83t-sid + - allwinner,sun8i-h3-sid + - allwinner,sun50i-a64-sid + - allwinner,sun50i-h5-sid + - allwinner,sun50i-h6-sid + + reg: + maxItems: 1 + +required: + - compatible + - reg + +# FIXME: We should set it, but it would report all the generic +# properties as additional properties. +# additionalProperties: false + +examples: + - | + efuse@1c23800 { + compatible = "allwinner,sun4i-a10-sid"; + reg = <0x01c23800 0x10>; + }; + + - | + efuse@1c23800 { + compatible = "allwinner,sun7i-a20-sid"; + reg = <0x01c23800 0x200>; + }; + +... diff --git a/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt b/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt deleted file mode 100644 index cfb18b4ef8f7..000000000000 --- a/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt +++ /dev/null @@ -1,29 +0,0 @@ -Allwinner sunxi-sid - -Required properties: -- compatible: Should be one of the following: - "allwinner,sun4i-a10-sid" - "allwinner,sun7i-a20-sid" - "allwinner,sun8i-a83t-sid" - "allwinner,sun8i-h3-sid" - "allwinner,sun50i-a64-sid" - "allwinner,sun50i-h5-sid" - "allwinner,sun50i-h6-sid" - -- reg: Should contain registers location and length - -= Data cells = -Are child nodes of sunxi-sid, bindings of which as described in -bindings/nvmem/nvmem.txt - -Example for sun4i: - sid@1c23800 { - compatible = "allwinner,sun4i-a10-sid"; - reg = <0x01c23800 0x10> - }; - -Example for sun7i: - sid@1c23800 { - compatible = "allwinner,sun7i-a20-sid"; - reg = <0x01c23800 0x200> - }; diff --git a/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt b/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt index 68f7d6fdd140..904dadf3d07b 100644 --- a/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt +++ b/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt @@ -2,7 +2,7 @@ Freescale i.MX6 On-Chip OTP Controller (OCOTP) device tree bindings This binding represents the on-chip eFuse OTP controller found on i.MX6Q/D, i.MX6DL/S, i.MX6SL, i.MX6SX, i.MX6UL, i.MX6ULL/ULZ, i.MX6SLL, -i.MX7D/S, i.MX7ULP and i.MX8MQ SoCs. +i.MX7D/S, i.MX7ULP, i.MX8MQ, i.MX8MM and i.MX8MN SoCs. Required properties: - compatible: should be one of @@ -15,6 +15,8 @@ Required properties: "fsl,imx6sll-ocotp" (i.MX6SLL), "fsl,imx7ulp-ocotp" (i.MX7ULP), "fsl,imx8mq-ocotp" (i.MX8MQ), + "fsl,imx8mm-ocotp" (i.MX8MM), + "fsl,imx8mn-ocotp" (i.MX8MN), followed by "syscon". - #address-cells : Should be 1 - #size-cells : Should be 1 diff --git a/Documentation/devicetree/bindings/nvmem/nvmem-consumer.yaml b/Documentation/devicetree/bindings/nvmem/nvmem-consumer.yaml new file mode 100644 index 000000000000..b7c00ed31085 --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/nvmem-consumer.yaml @@ -0,0 +1,45 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/nvmem/nvmem-consumer.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVMEM (Non Volatile Memory) Consumer Device Tree Bindings + +maintainers: + - Srinivas Kandagatla <srinivas.kandagatla@linaro.org> + +select: true + +properties: + nvmem: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + List of phandle to the nvmem providers. + + nvmem-cells: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + List of phandle to the nvmem data cells. + + nvmem-names: + $ref: /schemas/types.yaml#/definitions/string-array + description: + Names for the each nvmem provider. + + nvmem-cell-names: + $ref: /schemas/types.yaml#/definitions/string-array + description: + Names for each nvmem-cells specified. + +dependencies: + nvmem-names: [ nvmem ] + nvmem-cell-names: [ nvmem-cells ] + +examples: + - | + tsens { + /* ... */ + nvmem-cells = <&tsens_calibration>; + nvmem-cell-names = "calibration"; + }; diff --git a/Documentation/devicetree/bindings/nvmem/nvmem.txt b/Documentation/devicetree/bindings/nvmem/nvmem.txt index fd06c09b822b..46a7ef485e24 100644 --- a/Documentation/devicetree/bindings/nvmem/nvmem.txt +++ b/Documentation/devicetree/bindings/nvmem/nvmem.txt @@ -1,80 +1 @@ -= NVMEM(Non Volatile Memory) Data Device Tree Bindings = - -This binding is intended to represent the location of hardware -configuration data stored in NVMEMs like eeprom, efuses and so on. - -On a significant proportion of boards, the manufacturer has stored -some data on NVMEM, for the OS to be able to retrieve these information -and act upon it. Obviously, the OS has to know about where to retrieve -these data from, and where they are stored on the storage device. - -This document is here to document this. - -= Data providers = -Contains bindings specific to provider drivers and data cells as children -of this node. - -Optional properties: - read-only: Mark the provider as read only. - -= Data cells = -These are the child nodes of the provider which contain data cell -information like offset and size in nvmem provider. - -Required properties: -reg: specifies the offset in byte within the storage device. - -Optional properties: - -bits: Is pair of bit location and number of bits, which specifies offset - in bit and number of bits within the address range specified by reg property. - Offset takes values from 0-7. - -For example: - - /* Provider */ - qfprom: qfprom@700000 { - ... - - /* Data cells */ - tsens_calibration: calib@404 { - reg = <0x404 0x10>; - }; - - tsens_calibration_bckp: calib_bckp@504 { - reg = <0x504 0x11>; - bits = <6 128> - }; - - pvs_version: pvs-version@6 { - reg = <0x6 0x2> - bits = <7 2> - }; - - speed_bin: speed-bin@c{ - reg = <0xc 0x1>; - bits = <2 3>; - - }; - ... - }; - -= Data consumers = -Are device nodes which consume nvmem data cells/providers. - -Required-properties: -nvmem-cells: list of phandle to the nvmem data cells. -nvmem-cell-names: names for the each nvmem-cells specified. Required if - nvmem-cells is used. - -Optional-properties: -nvmem : list of phandles to nvmem providers. -nvmem-names: names for the each nvmem provider. required if nvmem is used. - -For example: - - tsens { - ... - nvmem-cells = <&tsens_calibration>; - nvmem-cell-names = "calibration"; - }; +This file has been moved to nvmem.yaml and nvmem-consumer.yaml. diff --git a/Documentation/devicetree/bindings/nvmem/nvmem.yaml b/Documentation/devicetree/bindings/nvmem/nvmem.yaml new file mode 100644 index 000000000000..1c75a059206c --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/nvmem.yaml @@ -0,0 +1,93 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/nvmem/nvmem.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVMEM (Non Volatile Memory) Device Tree Bindings + +maintainers: + - Srinivas Kandagatla <srinivas.kandagatla@linaro.org> + +description: | + This binding is intended to represent the location of hardware + configuration data stored in NVMEMs like eeprom, efuses and so on. + + On a significant proportion of boards, the manufacturer has stored + some data on NVMEM, for the OS to be able to retrieve these + information and act upon it. Obviously, the OS has to know about + where to retrieve these data from, and where they are stored on the + storage device. + +properties: + $nodename: + pattern: "^(eeprom|efuse|nvram)(@.*|-[0-9a-f])*$" + + "#address-cells": + const: 1 + + "#size-cells": + const: 1 + + read-only: + $ref: /schemas/types.yaml#/definitions/flag + description: + Mark the provider as read only. + +patternProperties: + "^.*@[0-9a-f]+$": + type: object + + properties: + reg: + maxItems: 1 + description: + Offset and size in bytes within the storage device. + + bits: + maxItems: 1 + items: + items: + - minimum: 0 + maximum: 7 + description: + Offset in bit within the address range specified by reg. + - minimum: 1 + description: + Size in bit within the address range specified by reg. + + required: + - reg + + additionalProperties: false + +examples: + - | + qfprom: eeprom@700000 { + #address-cells = <1>; + #size-cells = <1>; + + /* ... */ + + /* Data cells */ + tsens_calibration: calib@404 { + reg = <0x404 0x10>; + }; + + tsens_calibration_bckp: calib_bckp@504 { + reg = <0x504 0x11>; + bits = <6 128>; + }; + + pvs_version: pvs-version@6 { + reg = <0x6 0x2>; + bits = <7 2>; + }; + + speed_bin: speed-bin@c{ + reg = <0xc 0x1>; + bits = <2 3>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/opp/opp.txt b/Documentation/devicetree/bindings/opp/opp.txt index 76b6c79604a5..68592271461f 100644 --- a/Documentation/devicetree/bindings/opp/opp.txt +++ b/Documentation/devicetree/bindings/opp/opp.txt @@ -140,8 +140,8 @@ Optional properties: frequency for a short duration of time limited by the device's power, current and thermal limits. -- opp-suspend: Marks the OPP to be used during device suspend. Only one OPP in - the table should have this. +- opp-suspend: Marks the OPP to be used during device suspend. If multiple OPPs + in the table have this, the OPP with highest opp-hz will be used. - opp-supported-hw: This enables us to select only a subset of OPPs from the larger OPP table, based on what version of the hardware we are running on. We diff --git a/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt b/Documentation/devicetree/bindings/opp/qcom-nvmem-cpufreq.txt index c2127b96805a..4751029b9b74 100644 --- a/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt +++ b/Documentation/devicetree/bindings/opp/qcom-nvmem-cpufreq.txt @@ -1,25 +1,38 @@ -Qualcomm Technologies, Inc. KRYO CPUFreq and OPP bindings +Qualcomm Technologies, Inc. NVMEM CPUFreq and OPP bindings =================================== -In Certain Qualcomm Technologies, Inc. SoCs like apq8096 and msm8996 -that have KRYO processors, the CPU ferequencies subset and voltage value -of each OPP varies based on the silicon variant in use. +In Certain Qualcomm Technologies, Inc. SoCs like apq8096 and msm8996, +the CPU frequencies subset and voltage value of each OPP varies based on +the silicon variant in use. Qualcomm Technologies, Inc. Process Voltage Scaling Tables defines the voltage and frequency value based on the msm-id in SMEM and speedbin blown in the efuse combination. -The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC +The qcom-cpufreq-nvmem driver reads the msm-id and efuse value from the SoC to provide the OPP framework with required information (existing HW bitmap). This is used to determine the voltage and frequency value for each OPP of operating-points-v2 table when it is parsed by the OPP framework. Required properties: -------------------- -In 'cpus' nodes: +In 'cpu' nodes: - operating-points-v2: Phandle to the operating-points-v2 table to use. In 'operating-points-v2' table: - compatible: Should be - 'operating-points-v2-kryo-cpu' for apq8096 and msm8996. + +Optional properties: +-------------------- +In 'cpu' nodes: +- power-domains: A phandle pointing to the PM domain specifier which provides + the performance states available for active state management. + Please refer to the power-domains bindings + Documentation/devicetree/bindings/power/power_domain.txt + and also examples below. +- power-domain-names: Should be + - 'cpr' for qcs404. + +In 'operating-points-v2' table: - nvmem-cells: A phandle pointing to a nvmem-cells node representing the efuse registers that has information about the speedbin that is used to select the right frequency/voltage @@ -678,3 +691,105 @@ soc { }; }; }; + +Example 2: +--------- + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + CPU0: cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x100>; + .... + clocks = <&apcs_glb>; + operating-points-v2 = <&cpu_opp_table>; + power-domains = <&cpr>; + power-domain-names = "cpr"; + }; + + CPU1: cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x101>; + .... + clocks = <&apcs_glb>; + operating-points-v2 = <&cpu_opp_table>; + power-domains = <&cpr>; + power-domain-names = "cpr"; + }; + + CPU2: cpu@102 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x102>; + .... + clocks = <&apcs_glb>; + operating-points-v2 = <&cpu_opp_table>; + power-domains = <&cpr>; + power-domain-names = "cpr"; + }; + + CPU3: cpu@103 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x103>; + .... + clocks = <&apcs_glb>; + operating-points-v2 = <&cpu_opp_table>; + power-domains = <&cpr>; + power-domain-names = "cpr"; + }; + }; + + cpu_opp_table: cpu-opp-table { + compatible = "operating-points-v2-kryo-cpu"; + opp-shared; + + opp-1094400000 { + opp-hz = /bits/ 64 <1094400000>; + required-opps = <&cpr_opp1>; + }; + opp-1248000000 { + opp-hz = /bits/ 64 <1248000000>; + required-opps = <&cpr_opp2>; + }; + opp-1401600000 { + opp-hz = /bits/ 64 <1401600000>; + required-opps = <&cpr_opp3>; + }; + }; + + cpr_opp_table: cpr-opp-table { + compatible = "operating-points-v2-qcom-level"; + + cpr_opp1: opp1 { + opp-level = <1>; + qcom,opp-fuse-level = <1>; + }; + cpr_opp2: opp2 { + opp-level = <2>; + qcom,opp-fuse-level = <2>; + }; + cpr_opp3: opp3 { + opp-level = <3>; + qcom,opp-fuse-level = <3>; + }; + }; + +.... + +soc { +.... + cpr: power-controller@b018000 { + compatible = "qcom,qcs404-cpr", "qcom,cpr"; + reg = <0x0b018000 0x1000>; + .... + vdd-apc-supply = <&pms405_s3>; + #power-domain-cells = <0>; + operating-points-v2 = <&cpr_opp_table>; + .... + }; +}; diff --git a/Documentation/devicetree/bindings/opp/qcom-opp.txt b/Documentation/devicetree/bindings/opp/qcom-opp.txt new file mode 100644 index 000000000000..32eb0793c7e6 --- /dev/null +++ b/Documentation/devicetree/bindings/opp/qcom-opp.txt @@ -0,0 +1,19 @@ +Qualcomm OPP bindings to describe OPP nodes + +The bindings are based on top of the operating-points-v2 bindings +described in Documentation/devicetree/bindings/opp/opp.txt +Additional properties are described below. + +* OPP Table Node + +Required properties: +- compatible: Allow OPPs to express their compatibility. It should be: + "operating-points-v2-qcom-level" + +* OPP Node + +Required properties: +- qcom,opp-fuse-level: A positive value representing the fuse corner/level + associated with this OPP node. Sometimes several corners/levels shares + a certain fuse corner/level. A fuse corner/level contains e.g. ref uV, + min uV, and max uV. diff --git a/Documentation/devicetree/bindings/opp/sun50i-nvmem-cpufreq.txt b/Documentation/devicetree/bindings/opp/sun50i-nvmem-cpufreq.txt new file mode 100644 index 000000000000..7deae57a587b --- /dev/null +++ b/Documentation/devicetree/bindings/opp/sun50i-nvmem-cpufreq.txt @@ -0,0 +1,167 @@ +Allwinner Technologies, Inc. NVMEM CPUFreq and OPP bindings +=================================== + +For some SoCs, the CPU frequency subset and voltage value of each OPP +varies based on the silicon variant in use. Allwinner Process Voltage +Scaling Tables defines the voltage and frequency value based on the +speedbin blown in the efuse combination. The sun50i-cpufreq-nvmem driver +reads the efuse value from the SoC to provide the OPP framework with +required information. + +Required properties: +-------------------- +In 'cpus' nodes: +- operating-points-v2: Phandle to the operating-points-v2 table to use. + +In 'operating-points-v2' table: +- compatible: Should be + - 'allwinner,sun50i-h6-operating-points'. +- nvmem-cells: A phandle pointing to a nvmem-cells node representing the + efuse registers that has information about the speedbin + that is used to select the right frequency/voltage value + pair. Please refer the for nvmem-cells bindings + Documentation/devicetree/bindings/nvmem/nvmem.txt and + also examples below. + +In every OPP node: +- opp-microvolt-<name>: Voltage in micro Volts. + At runtime, the platform can pick a <name> and + matching opp-microvolt-<name> property. + [See: opp.txt] + HW: <name>: + sun50i-h6 speed0 speed1 speed2 + +Example 1: +--------- + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + compatible = "arm,cortex-a53"; + device_type = "cpu"; + reg = <0>; + enable-method = "psci"; + clocks = <&ccu CLK_CPUX>; + clock-latency-ns = <244144>; /* 8 32k periods */ + operating-points-v2 = <&cpu_opp_table>; + #cooling-cells = <2>; + }; + + cpu1: cpu@1 { + compatible = "arm,cortex-a53"; + device_type = "cpu"; + reg = <1>; + enable-method = "psci"; + clocks = <&ccu CLK_CPUX>; + clock-latency-ns = <244144>; /* 8 32k periods */ + operating-points-v2 = <&cpu_opp_table>; + #cooling-cells = <2>; + }; + + cpu2: cpu@2 { + compatible = "arm,cortex-a53"; + device_type = "cpu"; + reg = <2>; + enable-method = "psci"; + clocks = <&ccu CLK_CPUX>; + clock-latency-ns = <244144>; /* 8 32k periods */ + operating-points-v2 = <&cpu_opp_table>; + #cooling-cells = <2>; + }; + + cpu3: cpu@3 { + compatible = "arm,cortex-a53"; + device_type = "cpu"; + reg = <3>; + enable-method = "psci"; + clocks = <&ccu CLK_CPUX>; + clock-latency-ns = <244144>; /* 8 32k periods */ + operating-points-v2 = <&cpu_opp_table>; + #cooling-cells = <2>; + }; + }; + + cpu_opp_table: opp_table { + compatible = "allwinner,sun50i-h6-operating-points"; + nvmem-cells = <&speedbin_efuse>; + opp-shared; + + opp@480000000 { + clock-latency-ns = <244144>; /* 8 32k periods */ + opp-hz = /bits/ 64 <480000000>; + + opp-microvolt-speed0 = <880000>; + opp-microvolt-speed1 = <820000>; + opp-microvolt-speed2 = <800000>; + }; + + opp@720000000 { + clock-latency-ns = <244144>; /* 8 32k periods */ + opp-hz = /bits/ 64 <720000000>; + + opp-microvolt-speed0 = <880000>; + opp-microvolt-speed1 = <820000>; + opp-microvolt-speed2 = <800000>; + }; + + opp@816000000 { + clock-latency-ns = <244144>; /* 8 32k periods */ + opp-hz = /bits/ 64 <816000000>; + + opp-microvolt-speed0 = <880000>; + opp-microvolt-speed1 = <820000>; + opp-microvolt-speed2 = <800000>; + }; + + opp@888000000 { + clock-latency-ns = <244144>; /* 8 32k periods */ + opp-hz = /bits/ 64 <888000000>; + + opp-microvolt-speed0 = <940000>; + opp-microvolt-speed1 = <820000>; + opp-microvolt-speed2 = <800000>; + }; + + opp@1080000000 { + clock-latency-ns = <244144>; /* 8 32k periods */ + opp-hz = /bits/ 64 <1080000000>; + + opp-microvolt-speed0 = <1060000>; + opp-microvolt-speed1 = <880000>; + opp-microvolt-speed2 = <840000>; + }; + + opp@1320000000 { + clock-latency-ns = <244144>; /* 8 32k periods */ + opp-hz = /bits/ 64 <1320000000>; + + opp-microvolt-speed0 = <1160000>; + opp-microvolt-speed1 = <940000>; + opp-microvolt-speed2 = <900000>; + }; + + opp@1488000000 { + clock-latency-ns = <244144>; /* 8 32k periods */ + opp-hz = /bits/ 64 <1488000000>; + + opp-microvolt-speed0 = <1160000>; + opp-microvolt-speed1 = <1000000>; + opp-microvolt-speed2 = <960000>; + }; + }; +.... +soc { +.... + sid: sid@3006000 { + compatible = "allwinner,sun50i-h6-sid"; + reg = <0x03006000 0x400>; + #address-cells = <1>; + #size-cells = <1>; + .... + speedbin_efuse: speed@1c { + reg = <0x1c 4>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/pci/83xx-512x-pci.txt b/Documentation/devicetree/bindings/pci/83xx-512x-pci.txt index b9165b72473c..3abeecf4983f 100644 --- a/Documentation/devicetree/bindings/pci/83xx-512x-pci.txt +++ b/Documentation/devicetree/bindings/pci/83xx-512x-pci.txt @@ -9,7 +9,6 @@ Freescale 83xx and 512x SOCs include the same PCI bridge core. Example (MPC8313ERDB) pci0: pci@e0008500 { - cell-index = <1>; interrupt-map-mask = <0xf800 0x0 0x0 0x7>; interrupt-map = < /* IDSEL 0x0E -mini PCI */ diff --git a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt index 12b18f82d441..efa2c8b9b85a 100644 --- a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt +++ b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt @@ -3,7 +3,7 @@ Amlogic Meson AXG DWC PCIE SoC controller Amlogic Meson PCIe host controller is based on the Synopsys DesignWare PCI core. It shares common functions with the PCIe DesignWare core driver and inherits common properties defined in -Documentation/devicetree/bindings/pci/designware-pci.txt. +Documentation/devicetree/bindings/pci/designware-pcie.txt. Additional properties are described here: diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt index 5561a1c060d0..78494c4050f7 100644 --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -11,7 +11,6 @@ Required properties: the ATU address space. (The old way of getting the configuration address space from "ranges" is deprecated and should be avoided.) -- num-lanes: number of lanes to use RC mode: - #address-cells: set to <3> - #size-cells: set to <2> @@ -34,6 +33,11 @@ Optional properties: - clock-names: Must include the following entries: - "pcie" - "pcie_bus" +- snps,enable-cdm-check: This is a boolean property and if present enables + automatic checking of CDM (Configuration Dependent Module) registers + for data corruption. CDM registers include standard PCIe configuration + space registers, Port Logic registers, DMA and iATU (internal Address + Translation Unit) registers. RC mode: - num-viewport: number of view ports configured in hardware. If a platform does not specify it, the driver assumes 2. diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt index a7f5f5afa0e6..de4b2baf91e8 100644 --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -50,7 +50,7 @@ Additional required properties for imx7d-pcie and imx8mq-pcie: - power-domains: Must be set to a phandle pointing to PCIE_PHY power domain - resets: Must contain phandles to PCIe-related reset lines exposed by SRC IP block -- reset-names: Must contain the following entires: +- reset-names: Must contain the following entries: - "pciephy" - "apps" - "turnoff" diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt index 92437a366e5f..7468d666763a 100644 --- a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt +++ b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt @@ -6,6 +6,7 @@ Required properties: "mediatek,mt2712-pcie" "mediatek,mt7622-pcie" "mediatek,mt7623-pcie" + "mediatek,mt7629-pcie" - device_type: Must be "pci" - reg: Base addresses and lengths of the PCIe subsys and root ports. - reg-names: Names of the above areas to use during resource lookup. diff --git a/Documentation/devicetree/bindings/pci/mobiveil-pcie.txt b/Documentation/devicetree/bindings/pci/mobiveil-pcie.txt index a618d4787dd7..64156993e052 100644 --- a/Documentation/devicetree/bindings/pci/mobiveil-pcie.txt +++ b/Documentation/devicetree/bindings/pci/mobiveil-pcie.txt @@ -10,8 +10,10 @@ Required properties: interrupt source. The value must be 1. - compatible: Should contain "mbvl,gpex40-pcie" - reg: Should contain PCIe registers location and length + Mandatory: "config_axi_slave": PCIe controller registers "csr_axi_slave" : Bridge config registers + Optional: "gpio_slave" : GPIO registers to control slot power "apb_csr" : MSI registers diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt new file mode 100644 index 000000000000..b739f92da58e --- /dev/null +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt @@ -0,0 +1,171 @@ +NVIDIA Tegra PCIe controller (Synopsys DesignWare Core based) + +This PCIe host controller is based on the Synopsis Designware PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: +- compatible: For Tegra19x, must contain "nvidia,tegra194-pcie". +- device_type: Must be "pci" +- power-domains: A phandle to the node that controls power to the respective + PCIe controller and a specifier name for the PCIe controller. Following are + the specifiers for the different PCIe controllers + TEGRA194_POWER_DOMAIN_PCIEX8B: C0 + TEGRA194_POWER_DOMAIN_PCIEX1A: C1 + TEGRA194_POWER_DOMAIN_PCIEX1A: C2 + TEGRA194_POWER_DOMAIN_PCIEX1A: C3 + TEGRA194_POWER_DOMAIN_PCIEX4A: C4 + TEGRA194_POWER_DOMAIN_PCIEX8A: C5 + these specifiers are defined in + "include/dt-bindings/power/tegra194-powergate.h" file. +- reg: A list of physical base address and length pairs for each set of + controller registers. Must contain an entry for each entry in the reg-names + property. +- reg-names: Must include the following entries: + "appl": Controller's application logic registers + "config": As per the definition in designware-pcie.txt + "atu_dma": iATU and DMA registers. This is where the iATU (internal Address + Translation Unit) registers of the PCIe core are made available + for SW access. + "dbi": The aperture where root port's own configuration registers are + available +- interrupts: A list of interrupt outputs of the controller. Must contain an + entry for each entry in the interrupt-names property. +- interrupt-names: Must include the following entries: + "intr": The Tegra interrupt that is asserted for controller interrupts + "msi": The Tegra interrupt that is asserted when an MSI is received +- bus-range: Range of bus numbers associated with this controller +- #address-cells: Address representation for root ports (must be 3) + - cell 0 specifies the bus and device numbers of the root port: + [23:16]: bus number + [15:11]: device number + - cell 1 denotes the upper 32 address bits and should be 0 + - cell 2 contains the lower 32 address bits and is used to translate to the + CPU address space +- #size-cells: Size representation for root ports (must be 2) +- ranges: Describes the translation of addresses for root ports and standard + PCI regions. The entries must be 7 cells each, where the first three cells + correspond to the address as described for the #address-cells property + above, the fourth and fifth cells are for the physical CPU address to + translate to and the sixth and seventh cells are as described for the + #size-cells property above. + - Entries setup the mapping for the standard I/O, memory and + prefetchable PCI regions. The first cell determines the type of region + that is setup: + - 0x81000000: I/O memory region + - 0x82000000: non-prefetchable memory region + - 0xc2000000: prefetchable memory region + Please refer to the standard PCI bus binding document for a more detailed + explanation. +- #interrupt-cells: Size representation for interrupts (must be 1) +- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties + Please refer to the standard PCI bus binding document for a more detailed + explanation. +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - core +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - apb + - core +- phys: Must contain a phandle to P2U PHY for each entry in phy-names. +- phy-names: Must include an entry for each active lane. + "p2u-N": where N ranges from 0 to one less than the total number of lanes +- nvidia,bpmp: Must contain a pair of phandle to BPMP controller node followed + by controller-id. Following are the controller ids for each controller. + 0: C0 + 1: C1 + 2: C2 + 3: C3 + 4: C4 + 5: C5 +- vddio-pex-ctl-supply: Regulator supply for PCIe side band signals + +Optional properties: +- pinctrl-names: A list of pinctrl state names. + It is mandatory for C5 controller and optional for other controllers. + - "default": Configures PCIe I/O for proper operation. +- pinctrl-0: phandle for the 'default' state of pin configuration. + It is mandatory for C5 controller and optional for other controllers. +- supports-clkreq: Refer to Documentation/devicetree/bindings/pci/pci.txt +- nvidia,update-fc-fixup: This is a boolean property and needs to be present to + improve performance when a platform is designed in such a way that it + satisfies at least one of the following conditions thereby enabling root + port to exchange optimum number of FC (Flow Control) credits with + downstream devices + 1. If C0/C4/C5 run at x1/x2 link widths (irrespective of speed and MPS) + 2. If C0/C1/C2/C3/C4/C5 operate at their respective max link widths and + a) speed is Gen-2 and MPS is 256B + b) speed is >= Gen-3 with any MPS +- nvidia,aspm-cmrt-us: Common Mode Restore Time for proper operation of ASPM + to be specified in microseconds +- nvidia,aspm-pwr-on-t-us: Power On time for proper operation of ASPM to be + specified in microseconds +- nvidia,aspm-l0s-entrance-latency-us: ASPM L0s entrance latency to be + specified in microseconds +- vpcie3v3-supply: A phandle to the regulator node that supplies 3.3V to the slot + if the platform has one such slot. (Ex:- x16 slot owned by C5 controller + in p2972-0000 platform). +- vpcie12v-supply: A phandle to the regulator node that supplies 12V to the slot + if the platform has one such slot. (Ex:- x16 slot owned by C5 controller + in p2972-0000 platform). + +Examples: +========= + +Tegra194: +-------- + + pcie@14180000 { + compatible = "nvidia,tegra194-pcie", "snps,dw-pcie"; + power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8B>; + reg = <0x00 0x14180000 0x0 0x00020000 /* appl registers (128K) */ + 0x00 0x38000000 0x0 0x00040000 /* configuration space (256K) */ + 0x00 0x38040000 0x0 0x00040000>; /* iATU_DMA reg space (256K) */ + reg-names = "appl", "config", "atu_dma"; + + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + num-lanes = <8>; + linux,pci-domain = <0>; + + pinctrl-names = "default"; + pinctrl-0 = <&pex_rst_c5_out_state>, <&clkreq_c5_bi_dir_state>; + + clocks = <&bpmp TEGRA194_CLK_PEX0_CORE_0>; + clock-names = "core"; + + resets = <&bpmp TEGRA194_RESET_PEX0_CORE_0_APB>, + <&bpmp TEGRA194_RESET_PEX0_CORE_0>; + reset-names = "apb", "core"; + + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */ + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; + + nvidia,bpmp = <&bpmp 0>; + + supports-clkreq; + nvidia,aspm-cmrt-us = <60>; + nvidia,aspm-pwr-on-t-us = <20>; + nvidia,aspm-l0s-entrance-latency-us = <3>; + + bus-range = <0x0 0xff>; + ranges = <0x81000000 0x0 0x38100000 0x0 0x38100000 0x0 0x00100000 /* downstream I/O (1MB) */ + 0x82000000 0x0 0x38200000 0x0 0x38200000 0x0 0x01E00000 /* non-prefetchable memory (30MB) */ + 0xc2000000 0x18 0x00000000 0x18 0x00000000 0x4 0x00000000>; /* prefetchable memory (16GB) */ + + vddio-pex-ctl-supply = <&vdd_1v8ao>; + vpcie3v3-supply = <&vdd_3v3_pcie>; + vpcie12v-supply = <&vdd_12v_pcie>; + + phys = <&p2u_hsio_2>, <&p2u_hsio_3>, <&p2u_hsio_4>, + <&p2u_hsio_5>; + phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3"; + }; diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt index 145a4f04194f..7939bca47861 100644 --- a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt @@ -65,6 +65,14 @@ Required properties: - afi - pcie_x +Optional properties: +- pinctrl-names: A list of pinctrl state names. Must contain the following + entries: + - "default": active state, puts PCIe I/O out of deep power down state + - "idle": puts PCIe I/O into deep power down state +- pinctrl-0: phandle for the default/active state of pin configurations. +- pinctrl-1: phandle for the idle state of pin configurations. + Required properties on Tegra124 and later (deprecated): - phys: Must contain an entry for each entry in phy-names. - phy-names: Must include the following entries: diff --git a/Documentation/devicetree/bindings/pci/pci-armada8k.txt b/Documentation/devicetree/bindings/pci/pci-armada8k.txt index 9e3fc15e1af8..7a813d0e6d63 100644 --- a/Documentation/devicetree/bindings/pci/pci-armada8k.txt +++ b/Documentation/devicetree/bindings/pci/pci-armada8k.txt @@ -11,12 +11,20 @@ Required properties: - reg-names: - "ctrl" for the control register region - "config" for the config space region -- interrupts: Interrupt specifier for the PCIe controler +- interrupts: Interrupt specifier for the PCIe controller - clocks: reference to the PCIe controller clocks - clock-names: mandatory if there is a second clock, in this case the name must be "core" for the first clock and "reg" for the second one +Optional properties: +- phys: phandle(s) to PHY node(s) following the generic PHY bindings. + Either 1, 2 or 4 PHYs might be needed depending on the number of + PCIe lanes. +- phy-names: names of the PHYs corresponding to the number of lanes. + Must be "cp0-pcie0-x4-lane0-phy", "cp0-pcie0-x4-lane1-phy" for + 2 PHYs. + Example: pcie@f2600000 { diff --git a/Documentation/devicetree/bindings/pci/pci-msi.txt b/Documentation/devicetree/bindings/pci/pci-msi.txt index 9b3cc817d181..b73d839657b6 100644 --- a/Documentation/devicetree/bindings/pci/pci-msi.txt +++ b/Documentation/devicetree/bindings/pci/pci-msi.txt @@ -201,7 +201,7 @@ Example (5) #msi-cells = <1>; }; - pci: pci@c { + pci: pci@f { reg = <0xf 0x1>; compatible = "vendor,pcie-root-complex"; device_type = "pci"; diff --git a/Documentation/devicetree/bindings/pci/pci.txt b/Documentation/devicetree/bindings/pci/pci.txt index 92c01db610df..29bcbd88f457 100644 --- a/Documentation/devicetree/bindings/pci/pci.txt +++ b/Documentation/devicetree/bindings/pci/pci.txt @@ -24,6 +24,14 @@ driver implementation may support the following properties: unsupported link speed, for instance, trying to do training for unsupported link speed, etc. Must be '4' for gen4, '3' for gen3, '2' for gen2, and '1' for gen1. Any other values are invalid. +- reset-gpios: + If present this property specifies PERST# GPIO. Host drivers can parse the + GPIO and apply fundamental reset to endpoints. +- supports-clkreq: + If present this property specifies that CLKREQ signal routing exists from + root port to downstream device and host bridge drivers can do programming + which depends on CLKREQ signal existence. For example, programming root port + not to advertise ASPM L1 Sub-States support if there is no CLKREQ signal. PCI-PCI Bridge properties ------------------------- diff --git a/Documentation/devicetree/bindings/pci/pcie-al.txt b/Documentation/devicetree/bindings/pci/pcie-al.txt new file mode 100644 index 000000000000..557a5089229d --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pcie-al.txt @@ -0,0 +1,46 @@ +* Amazon Annapurna Labs PCIe host bridge + +Amazon's Annapurna Labs PCIe Host Controller is based on the Synopsys DesignWare +PCI core. It inherits common properties defined in +Documentation/devicetree/bindings/pci/designware-pcie.txt. + +Properties of the host controller node that differ from it are: + +- compatible: + Usage: required + Value type: <stringlist> + Definition: Value should contain + - "amazon,al-alpine-v2-pcie" for alpine_v2 + - "amazon,al-alpine-v3-pcie" for alpine_v3 + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: Register ranges as listed in the reg-names property + +- reg-names: + Usage: required + Value type: <stringlist> + Definition: Must include the following entries + - "config" PCIe ECAM space + - "controller" AL proprietary registers + - "dbi" Designware PCIe registers + +Example: + + pcie-external0: pcie@fb600000 { + compatible = "amazon,al-alpine-v3-pcie"; + reg = <0x0 0xfb600000 0x0 0x00100000 + 0x0 0xfd800000 0x0 0x00010000 + 0x0 0xfd810000 0x0 0x00001000>; + reg-names = "config", "controller", "dbi"; + bus-range = <0 255>; + device_type = "pci"; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; + interrupt-map-mask = <0x00 0 0 7>; + interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; /* INTa */ + ranges = <0x02000000 0x0 0xc0010000 0x0 0xc0010000 0x0 0x07ff0000>; + }; diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt index 1fd703bd73e0..ada80b01bf0c 100644 --- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt @@ -10,6 +10,7 @@ - "qcom,pcie-msm8996" for msm8996 or apq8096 - "qcom,pcie-ipq4019" for ipq4019 - "qcom,pcie-ipq8074" for ipq8074 + - "qcom,pcie-qcs404" for qcs404 - reg: Usage: required @@ -116,6 +117,15 @@ - "ahb" AHB clock - "aux" Auxiliary clock +- clock-names: + Usage: required for qcs404 + Value type: <stringlist> + Definition: Should contain the following entries + - "iface" AHB clock + - "aux" Auxiliary clock + - "master_bus" AXI Master clock + - "slave_bus" AXI Slave clock + - resets: Usage: required Value type: <prop-encoded-array> @@ -167,6 +177,17 @@ - "ahb" AHB Reset - "axi_m_sticky" AXI Master Sticky reset +- reset-names: + Usage: required for qcs404 + Value type: <stringlist> + Definition: Should contain the following entries + - "axi_m" AXI Master reset + - "axi_s" AXI Slave reset + - "axi_m_sticky" AXI Master Sticky reset + - "pipe_sticky" PIPE sticky reset + - "pwr" PWR reset + - "ahb" AHB reset + - power-domains: Usage: required for apq8084 and msm8996/apq8096 Value type: <prop-encoded-array> @@ -195,12 +216,12 @@ Definition: A phandle to the PCIe endpoint power supply - phys: - Usage: required for apq8084 + Usage: required for apq8084 and qcs404 Value type: <phandle> Definition: List of phandle(s) as listed in phy-names property - phy-names: - Usage: required for apq8084 + Usage: required for apq8084 and qcs404 Value type: <stringlist> Definition: Should contain "pciephy" diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt index 6904882a0e94..45bba9f88a51 100644 --- a/Documentation/devicetree/bindings/pci/rcar-pci.txt +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -3,6 +3,7 @@ Required properties: compatible: "renesas,pcie-r8a7743" for the R8A7743 SoC; "renesas,pcie-r8a7744" for the R8A7744 SoC; + "renesas,pcie-r8a774a1" for the R8A774A1 SoC; "renesas,pcie-r8a774c0" for the R8A774C0 SoC; "renesas,pcie-r8a7779" for the R8A7779 SoC; "renesas,pcie-r8a7790" for the R8A7790 SoC; diff --git a/Documentation/devicetree/bindings/perf/fsl-imx-ddr.txt b/Documentation/devicetree/bindings/perf/fsl-imx-ddr.txt new file mode 100644 index 000000000000..d77e3f26f9e6 --- /dev/null +++ b/Documentation/devicetree/bindings/perf/fsl-imx-ddr.txt @@ -0,0 +1,21 @@ +* Freescale(NXP) IMX8 DDR performance monitor + +Required properties: + +- compatible: should be one of: + "fsl,imx8-ddr-pmu" + "fsl,imx8m-ddr-pmu" + +- reg: physical address and size + +- interrupts: single interrupt + generated by the control block + +Example: + + ddr-pmu@5c020000 { + compatible = "fsl,imx8-ddr-pmu"; + reg = <0x5c020000 0x10000>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/phy/allwinner,sun6i-a31-mipi-dphy.yaml b/Documentation/devicetree/bindings/phy/allwinner,sun6i-a31-mipi-dphy.yaml new file mode 100644 index 000000000000..fa46670de299 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/allwinner,sun6i-a31-mipi-dphy.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/allwinner,sun6i-a31-mipi-dphy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A31 MIPI D-PHY Controller Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + "#phy-cells": + const: 0 + + compatible: + const: allwinner,sun6i-a31-mipi-dphy + + reg: + maxItems: 1 + + clocks: + items: + - description: Bus Clock + - description: Module Clock + + clock-names: + items: + - const: bus + - const: mod + + resets: + maxItems: 1 + +required: + - "#phy-cells" + - compatible + - reg + - clocks + - clock-names + - resets + +additionalProperties: false + +examples: + - | + dphy0: d-phy@1ca1000 { + compatible = "allwinner,sun6i-a31-mipi-dphy"; + reg = <0x01ca1000 0x1000>; + clocks = <&ccu 23>, <&ccu 97>; + clock-names = "bus", "mod"; + resets = <&ccu 4>; + #phy-cells = <0>; + }; + +... diff --git a/Documentation/devicetree/bindings/phy/amlogic,meson-g12a-usb2-phy.yaml b/Documentation/devicetree/bindings/phy/amlogic,meson-g12a-usb2-phy.yaml new file mode 100644 index 000000000000..51254b4e65dd --- /dev/null +++ b/Documentation/devicetree/bindings/phy/amlogic,meson-g12a-usb2-phy.yaml @@ -0,0 +1,63 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 BayLibre, SAS +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/phy/amlogic,meson-g12a-usb2-phy.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Amlogic G12A USB2 PHY + +maintainers: + - Neil Armstrong <narmstrong@baylibre.com> + +properties: + compatible: + enum: + - amlogic,meson-g12a-usb2-phy + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: xtal + + resets: + maxItems: 1 + + reset-names: + items: + - const: phy + + "#phy-cells": + const: 0 + + phy-supply: + maxItems: 1 + description: + Phandle to a regulator that provides power to the PHY. This + regulator will be managed during the PHY power on/off sequence. + +required: + - compatible + - reg + - clocks + - clock-names + - resets + - reset-names + - "#phy-cells" + +examples: + - | + phy@36000 { + compatible = "amlogic,meson-g12a-usb2-phy"; + reg = <0x36000 0x2000>; + clocks = <&xtal>; + clock-names = "xtal"; + resets = <&phy_reset>; + reset-names = "phy"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/amlogic,meson-g12a-usb3-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/amlogic,meson-g12a-usb3-pcie-phy.yaml new file mode 100644 index 000000000000..346f9c35427c --- /dev/null +++ b/Documentation/devicetree/bindings/phy/amlogic,meson-g12a-usb3-pcie-phy.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 BayLibre, SAS +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/phy/amlogic,meson-g12a-usb3-pcie-phy.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Amlogic G12A USB3 + PCIE Combo PHY + +maintainers: + - Neil Armstrong <narmstrong@baylibre.com> + +properties: + compatible: + enum: + - amlogic,meson-g12a-usb3-pcie-phy + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: ref_clk + + resets: + maxItems: 1 + + reset-names: + items: + - const: phy + + "#phy-cells": + const: 1 + +required: + - compatible + - reg + - clocks + - clock-names + - resets + - reset-names + - "#phy-cells" + +examples: + - | + phy@46000 { + compatible = "amlogic,meson-g12a-usb3-pcie-phy"; + reg = <0x46000 0x2000>; + clocks = <&ref_clk>; + clock-names = "ref_clk"; + resets = <&phy_reset>; + reset-names = "phy"; + #phy-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/phy/lantiq,vrx200-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/lantiq,vrx200-pcie-phy.yaml new file mode 100644 index 000000000000..8a56a8526cef --- /dev/null +++ b/Documentation/devicetree/bindings/phy/lantiq,vrx200-pcie-phy.yaml @@ -0,0 +1,95 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/lantiq,vrx200-pcie-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Lantiq VRX200 and ARX300 PCIe PHY Device Tree Bindings + +maintainers: + - Martin Blumenstingl <martin.blumenstingl@googlemail.com> + +properties: + "#phy-cells": + const: 1 + description: selects the PHY mode as defined in <dt-bindings/phy/phy-lantiq-vrx200-pcie.h> + + compatible: + enum: + - lantiq,vrx200-pcie-phy + - lantiq,arx300-pcie-phy + + reg: + maxItems: 1 + + clocks: + items: + - description: PHY module clock + - description: PDI register clock + + clock-names: + items: + - const: phy + - const: pdi + + resets: + items: + - description: exclusive PHY reset line + - description: shared reset line between the PCIe PHY and PCIe controller + + resets-names: + items: + - const: phy + - const: pcie + + lantiq,rcu: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle to the RCU syscon + + lantiq,rcu-endian-offset: + $ref: /schemas/types.yaml#/definitions/uint32 + description: the offset of the endian registers for this PHY instance in the RCU syscon + + lantiq,rcu-big-endian-mask: + $ref: /schemas/types.yaml#/definitions/uint32 + description: the mask to set the PDI (PHY) registers for this PHY instance to big endian + + big-endian: + description: Configures the PDI (PHY) registers in big-endian mode + type: boolean + + little-endian: + description: Configures the PDI (PHY) registers in big-endian mode + type: boolean + +required: + - "#phy-cells" + - compatible + - reg + - clocks + - clock-names + - resets + - reset-names + - lantiq,rcu + - lantiq,rcu-endian-offset + - lantiq,rcu-big-endian-mask + +additionalProperties: false + +examples: + - | + pcie0_phy: phy@106800 { + compatible = "lantiq,vrx200-pcie-phy"; + reg = <0x106800 0x100>; + lantiq,rcu = <&rcu0>; + lantiq,rcu-endian-offset = <0x4c>; + lantiq,rcu-big-endian-mask = <0x80>; /* bit 7 */ + big-endian; + clocks = <&pmu 32>, <&pmu 36>; + clock-names = "phy", "pdi"; + resets = <&reset0 12 24>, <&reset0 22 22>; + reset-names = "phy", "pcie"; + #phy-cells = <1>; + }; + +... diff --git a/Documentation/devicetree/bindings/phy/meson-g12a-usb2-phy.txt b/Documentation/devicetree/bindings/phy/meson-g12a-usb2-phy.txt deleted file mode 100644 index a6ebc3dea159..000000000000 --- a/Documentation/devicetree/bindings/phy/meson-g12a-usb2-phy.txt +++ /dev/null @@ -1,22 +0,0 @@ -* Amlogic G12A USB2 PHY binding - -Required properties: -- compatible: Should be "amlogic,meson-g12a-usb2-phy" -- reg: The base address and length of the registers -- #phys-cells: must be 0 (see phy-bindings.txt in this directory) -- clocks: a phandle to the clock of this PHY -- clock-names: must be "xtal" -- resets: a phandle to the reset line of this PHY -- reset-names: must be "phy" -- phy-supply: see phy-bindings.txt in this directory - -Example: - usb2_phy0: phy@36000 { - compatible = "amlogic,g12a-usb2-phy"; - reg = <0x0 0x36000 0x0 0x2000>; - clocks = <&xtal>; - clock-names = "xtal"; - resets = <&reset RESET_USB_PHY21>; - reset-names = "phy"; - #phy-cells = <0>; - }; diff --git a/Documentation/devicetree/bindings/phy/meson-g12a-usb3-pcie-phy.txt b/Documentation/devicetree/bindings/phy/meson-g12a-usb3-pcie-phy.txt deleted file mode 100644 index 7cfc17e2df31..000000000000 --- a/Documentation/devicetree/bindings/phy/meson-g12a-usb3-pcie-phy.txt +++ /dev/null @@ -1,22 +0,0 @@ -* Amlogic G12A USB3 + PCIE Combo PHY binding - -Required properties: -- compatible: Should be "amlogic,meson-g12a-usb3-pcie-phy" -- #phys-cells: must be 1. The cell number is used to select the phy mode - as defined in <dt-bindings/phy/phy.h> between PHY_TYPE_USB3 and PHY_TYPE_PCIE -- reg: The base address and length of the registers -- clocks: a phandle to the 100MHz reference clock of this PHY -- clock-names: must be "ref_clk" -- resets: phandle to the reset lines for the PHY control -- reset-names: must be "phy" - -Example: - usb3_pcie_phy: phy@46000 { - compatible = "amlogic,g12a-usb3-pcie-phy"; - reg = <0x0 0x46000 0x0 0x2000>; - clocks = <&clkc CLKID_PCIE_PLL>; - clock-names = "ref_clk"; - resets = <&reset RESET_PCIE_PHY>; - reset-names = "phy"; - #phy-cells = <1>; - }; diff --git a/Documentation/devicetree/bindings/phy/mixel,mipi-dsi-phy.txt b/Documentation/devicetree/bindings/phy/mixel,mipi-dsi-phy.txt new file mode 100644 index 000000000000..9b23407233c0 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/mixel,mipi-dsi-phy.txt @@ -0,0 +1,29 @@ +Mixel DSI PHY for i.MX8 + +The Mixel MIPI-DSI PHY IP block is e.g. found on i.MX8 platforms (along the +MIPI-DSI IP from Northwest Logic). It represents the physical layer for the +electrical signals for DSI. + +Required properties: +- compatible: Must be: + - "fsl,imx8mq-mipi-dphy" +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Must contain the following entries: + - "phy_ref": phandle and specifier referring to the DPHY ref clock +- reg: the register range of the PHY controller +- #phy-cells: number of cells in PHY, as defined in + Documentation/devicetree/bindings/phy/phy-bindings.txt + this must be <0> + +Optional properties: +- power-domains: phandle to power domain + +Example: + dphy: dphy@30a0030 { + compatible = "fsl,imx8mq-mipi-dphy"; + clocks = <&clk IMX8MQ_CLK_DSI_PHY_REF>; + clock-names = "phy_ref"; + reg = <0x30a00300 0x100>; + power-domains = <&pd_mipi0>; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt b/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt index 6ac98b3b5f57..c9f5c0caf8a9 100644 --- a/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt @@ -7,6 +7,7 @@ Required properties: * "fsl,imx6sl-usbphy" for imx6sl * "fsl,vf610-usbphy" for Vybrid vf610 * "fsl,imx6sx-usbphy" for imx6sx + * "fsl,imx7ulp-usbphy" for imx7ulp "fsl,imx23-usbphy" is still a fallback for other strings - reg: Should contain registers location and length - interrupts: Should contain phy interrupt @@ -23,7 +24,7 @@ Optional properties: the 17.78mA TX reference current. Default: 100 Example: -usbphy1: usbphy@20c9000 { +usbphy1: usb-phy@20c9000 { compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy"; reg = <0x020c9000 0x1000>; interrupts = <0 44 0x04>; diff --git a/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt index daedb15f322e..9fb682e47c29 100644 --- a/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt +++ b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt @@ -42,6 +42,18 @@ Required properties: - reset-names: Must include the following entries: - "padctl" +For Tegra124: +- avdd-pll-utmip-supply: UTMI PLL power supply. Must supply 1.8 V. +- avdd-pll-erefe-supply: PLLE reference PLL power supply. Must supply 1.05 V. +- avdd-pex-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V. +- hvdd-pex-pll-e-supply: High-voltage PLLE power supply. Must supply 3.3 V. + +For Tegra210: +- avdd-pll-utmip-supply: UTMI PLL power supply. Must supply 1.8 V. +- avdd-pll-uerefe-supply: PLLE reference PLL power supply. Must supply 1.05 V. +- dvdd-pex-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V. +- hvdd-pex-pll-e-supply: High-voltage PLLE power supply. Must supply 1.8 V. + For Tegra186: - avdd-pll-erefeut-supply: UPHY brick and reference clock as well as UTMI PHY power supply. Must supply 1.8 V. diff --git a/Documentation/devicetree/bindings/phy/phy-bindings.txt b/Documentation/devicetree/bindings/phy/phy-bindings.txt index a403b81d0679..c4eb38902533 100644 --- a/Documentation/devicetree/bindings/phy/phy-bindings.txt +++ b/Documentation/devicetree/bindings/phy/phy-bindings.txt @@ -1,5 +1,5 @@ This document explains only the device tree data binding. For general -information about PHY subsystem refer to Documentation/phy.txt +information about PHY subsystem refer to Documentation/driver-api/phy/phy.rst PHY device node =============== diff --git a/Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt b/Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt index cf2cd86db267..8c60e6985950 100644 --- a/Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt +++ b/Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt @@ -25,6 +25,13 @@ Required properties: - #address-cells: should be 1. - #size-cells: should be 0. +Optional properlties: + +- clocks: pointers to the reference clocks for this device (CP110 only), + consequently: MG clock, MG Core clock, AXI clock. +- clock-names: names of used clocks for CP110 only, must be : + "mg_clk", "mg_core_clk" and "axi_clk". + A sub-node is required for each comphy lane provided by the comphy. Required properties (child nodes): @@ -39,6 +46,9 @@ Examples: compatible = "marvell,comphy-cp110"; reg = <0x120000 0x6000>; marvell,system-controller = <&cpm_syscon0>; + clocks = <&CP110_LABEL(clk) 1 5>, <&CP110_LABEL(clk) 1 6>, + <&CP110_LABEL(clk) 1 18>; + clock-names = "mg_clk", "mg_core_clk", "axi_clk"; #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/phy/phy-pxa-usb.txt b/Documentation/devicetree/bindings/phy/phy-pxa-usb.txt new file mode 100644 index 000000000000..d80e36a77ec5 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-pxa-usb.txt @@ -0,0 +1,18 @@ +Marvell PXA USB PHY +------------------- + +Required properties: +- compatible: one of: "marvell,mmp2-usb-phy", "marvell,pxa910-usb-phy", + "marvell,pxa168-usb-phy", +- #phy-cells: must be 0 + +Example: + usb-phy: usbphy@d4207000 { + compatible = "marvell,mmp2-usb-phy"; + reg = <0xd4207000 0x40>; + #phy-cells = <0>; + status = "okay"; + }; + +This document explains the device tree binding. For general +information about PHY subsystem refer to Documentation/driver-api/phy/phy.rst diff --git a/Documentation/devicetree/bindings/phy/phy-tegra194-p2u.txt b/Documentation/devicetree/bindings/phy/phy-tegra194-p2u.txt new file mode 100644 index 000000000000..d23ff90baad5 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-tegra194-p2u.txt @@ -0,0 +1,28 @@ +NVIDIA Tegra194 P2U binding + +Tegra194 has two PHY bricks namely HSIO (High Speed IO) and NVHS (NVIDIA High +Speed) each interfacing with 12 and 8 P2U instances respectively. +A P2U instance is a glue logic between Synopsys DesignWare Core PCIe IP's PIPE +interface and PHY of HSIO/NVHS bricks. Each P2U instance represents one PCIe +lane. + +Required properties: +- compatible: For Tegra19x, must contain "nvidia,tegra194-p2u". +- reg: Should be the physical address space and length of respective each P2U + instance. +- reg-names: Must include the entry "ctl". + +Required properties for PHY port node: +- #phy-cells: Defined by generic PHY bindings. Must be 0. + +Refer to phy/phy-bindings.txt for the generic PHY binding properties. + +Example: + +p2u_hsio_0: phy@3e10000 { + compatible = "nvidia,tegra194-p2u"; + reg = <0x03e10000 0x10000>; + reg-names = "ctl"; + + #phy-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/phy/qcom-pcie2-phy.txt b/Documentation/devicetree/bindings/phy/qcom-pcie2-phy.txt new file mode 100644 index 000000000000..30064253f290 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom-pcie2-phy.txt @@ -0,0 +1,42 @@ +Qualcomm PCIe2 PHY controller +============================= + +The Qualcomm PCIe2 PHY is a Synopsys based phy found in a number of Qualcomm +platforms. + +Required properties: + - compatible: compatible list, should be: + "qcom,qcs404-pcie2-phy", "qcom,pcie2-phy" + + - reg: offset and length of the PHY register set. + - #phy-cells: must be 0. + + - clocks: a clock-specifier pair for the "pipe" clock + + - vdda-vp-supply: phandle to low voltage regulator + - vdda-vph-supply: phandle to high voltage regulator + + - resets: reset-specifier pairs for the "phy" and "pipe" resets + - reset-names: list of resets, should contain: + "phy" and "pipe" + + - clock-output-names: name of the outgoing clock signal from the PHY PLL + - #clock-cells: must be 0 + +Example: + phy@7786000 { + compatible = "qcom,qcs404-pcie2-phy", "qcom,pcie2-phy"; + reg = <0x07786000 0xb8>; + + clocks = <&gcc GCC_PCIE_0_PIPE_CLK>; + resets = <&gcc GCC_PCIEPHY_0_PHY_BCR>, + <&gcc GCC_PCIE_0_PIPE_ARES>; + reset-names = "phy", "pipe"; + + vdda-vp-supply = <&vreg_l3_1p05>; + vdda-vph-supply = <&vreg_l5_1p8>; + + clock-output-names = "pcie_0_pipe_clk"; + #clock-cells = <0>; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt index d46188f450bf..503a8cfb3184 100644 --- a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt +++ b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt @@ -1,10 +1,12 @@ * Renesas R-Car generation 3 USB 2.0 PHY This file provides information on what the device node for the R-Car generation -3, RZ/G1C and RZ/G2 USB 2.0 PHY contain. +3, RZ/G1C, RZ/G2 and RZ/A2 USB 2.0 PHY contain. Required properties: -- compatible: "renesas,usb2-phy-r8a77470" if the device is a part of an R8A77470 +- compatible: "renesas,usb2-phy-r7s9210" if the device is a part of an R7S9210 + SoC. + "renesas,usb2-phy-r8a77470" if the device is a part of an R8A77470 SoC. "renesas,usb2-phy-r8a774a1" if the device is a part of an R8A774A1 SoC. @@ -20,8 +22,8 @@ Required properties: R8A77990 SoC. "renesas,usb2-phy-r8a77995" if the device is a part of an R8A77995 SoC. - "renesas,rcar-gen3-usb2-phy" for a generic R-Car Gen3 or RZ/G2 - compatible device. + "renesas,rcar-gen3-usb2-phy" for a generic R-Car Gen3, RZ/G2 or + RZ/A2 compatible device. When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first @@ -46,6 +48,9 @@ channel as USB OTG: regulator will be managed during the PHY power on/off sequence. - renesas,no-otg-pins: boolean, specify when a board does not provide proper otg pins. +- dr_mode: string, indicates the working mode for the PHY. Can be "host", + "peripheral", or "otg". Should be set if otg controller is not used. + Example (R-Car H3): diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index cf96b7c20e4d..328585c6da58 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -24,6 +24,8 @@ Required properties: "allwinner,sun8i-h3-pinctrl" "allwinner,sun8i-h3-r-pinctrl" "allwinner,sun8i-r40-pinctrl" + "allwinner,sun8i-v3-pinctrl" + "allwinner,sun8i-v3s-pinctrl" "allwinner,sun50i-a64-pinctrl" "allwinner,sun50i-a64-r-pinctrl" "allwinner,sun50i-h5-pinctrl" diff --git a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml new file mode 100644 index 000000000000..39ad8657d018 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml @@ -0,0 +1,76 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/aspeed,ast2400-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ASPEED AST2400 Pin Controller + +maintainers: + - Andrew Jeffery <andrew@aj.id.au> + +description: |+ + The pin controller node should be the child of a syscon node with the + required property: + + - compatible: Should be one of the following: + "aspeed,ast2400-scu", "syscon", "simple-mfd" + + Refer to the the bindings described in + Documentation/devicetree/bindings/mfd/syscon.txt + +properties: + compatible: + const: aspeed,ast2400-pinctrl + +patternProperties: + '^.*$': + if: + type: object + then: + patternProperties: + "^function|groups$": + allOf: + - $ref: "/schemas/types.yaml#/definitions/string" + - enum: [ ACPI, ADC0, ADC1, ADC10, ADC11, ADC12, ADC13, ADC14, + ADC15, ADC2, ADC3, ADC4, ADC5, ADC6, ADC7, ADC8, ADC9, BMCINT, + DDCCLK, DDCDAT, EXTRST, FLACK, FLBUSY, FLWP, GPID, GPID0, GPID2, + GPID4, GPID6, GPIE0, GPIE2, GPIE4, GPIE6, I2C10, I2C11, I2C12, + I2C13, I2C14, I2C3, I2C4, I2C5, I2C6, I2C7, I2C8, I2C9, LPCPD, + LPCPME, LPCRST, LPCSMI, MAC1LINK, MAC2LINK, MDIO1, MDIO2, NCTS1, + NCTS2, NCTS3, NCTS4, NDCD1, NDCD2, NDCD3, NDCD4, NDSR1, NDSR2, + NDSR3, NDSR4, NDTR1, NDTR2, NDTR3, NDTR4, NDTS4, NRI1, NRI2, + NRI3, NRI4, NRTS1, NRTS2, NRTS3, OSCCLK, PWM0, PWM1, PWM2, PWM3, + PWM4, PWM5, PWM6, PWM7, RGMII1, RGMII2, RMII1, RMII2, ROM16, + ROM8, ROMCS1, ROMCS2, ROMCS3, ROMCS4, RXD1, RXD2, RXD3, RXD4, + SALT1, SALT2, SALT3, SALT4, SD1, SD2, SGPMCK, SGPMI, SGPMLD, + SGPMO, SGPSCK, SGPSI0, SGPSI1, SGPSLD, SIOONCTRL, SIOPBI, SIOPBO, + SIOPWREQ, SIOPWRGD, SIOS3, SIOS5, SIOSCI, SPI1, SPI1DEBUG, + SPI1PASSTHRU, SPICS1, TIMER3, TIMER4, TIMER5, TIMER6, TIMER7, + TIMER8, TXD1, TXD2, TXD3, TXD4, UART6, USB11D1, USB11H2, USB2D1, + USB2H1, USBCKI, VGABIOS_ROM, VGAHS, VGAVS, VPI18, VPI24, VPI30, + VPO12, VPO24, WDTRST1, WDTRST2 ] + +required: + - compatible + +examples: + - | + syscon: scu@1e6e2000 { + compatible = "aspeed,ast2400-scu", "syscon", "simple-mfd"; + reg = <0x1e6e2000 0x1a8>; + + pinctrl: pinctrl { + compatible = "aspeed,g4-pinctrl"; + + pinctrl_i2c3_default: i2c3_default { + function = "I2C3"; + groups = "I2C3"; + }; + + pinctrl_gpioh0_unbiased_default: gpioh0 { + pins = "A8"; + bias-disable; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml new file mode 100644 index 000000000000..3c6405be07ed --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml @@ -0,0 +1,126 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/aspeed,ast2500-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ASPEED AST2500 Pin Controller + +maintainers: + - Andrew Jeffery <andrew@aj.id.au> + +description: |+ + The pin controller node should be the child of a syscon node with the + required property: + + - compatible: Should be one of the following: + "aspeed,ast2500-scu", "syscon", "simple-mfd" + "aspeed,g5-scu", "syscon", "simple-mfd" + + Refer to the the bindings described in + Documentation/devicetree/bindings/mfd/syscon.txt + +properties: + compatible: + const: aspeed,ast2500-pinctrl + aspeed,external-nodes: + minItems: 2 + maxItems: 2 + allOf: + - $ref: /schemas/types.yaml#/definitions/phandle-array + description: | + A cell of phandles to external controller nodes: + 0: compatible with "aspeed,ast2500-gfx", "syscon" + 1: compatible with "aspeed,ast2500-lhc", "syscon" + +patternProperties: + '^.*$': + if: + type: object + then: + patternProperties: + "^function|groups$": + allOf: + - $ref: "/schemas/types.yaml#/definitions/string" + - enum: [ ACPI, ADC0, ADC1, ADC10, ADC11, ADC12, ADC13, ADC14, + ADC15, ADC2, ADC3, ADC4, ADC5, ADC6, ADC7, ADC8, ADC9, BMCINT, + DDCCLK, DDCDAT, ESPI, FWSPICS1, FWSPICS2, GPID0, GPID2, GPID4, + GPID6, GPIE0, GPIE2, GPIE4, GPIE6, I2C10, I2C11, I2C12, I2C13, + I2C14, I2C3, I2C4, I2C5, I2C6, I2C7, I2C8, I2C9, LAD0, LAD1, + LAD2, LAD3, LCLK, LFRAME, LPCHC, LPCPD, LPCPLUS, LPCPME, LPCRST, + LPCSMI, LSIRQ, MAC1LINK, MAC2LINK, MDIO1, MDIO2, NCTS1, NCTS2, + NCTS3, NCTS4, NDCD1, NDCD2, NDCD3, NDCD4, NDSR1, NDSR2, NDSR3, + NDSR4, NDTR1, NDTR2, NDTR3, NDTR4, NRI1, NRI2, NRI3, NRI4, NRTS1, + NRTS2, NRTS3, NRTS4, OSCCLK, PEWAKE, PNOR, PWM0, PWM1, PWM2, + PWM3, PWM4, PWM5, PWM6, PWM7, RGMII1, RGMII2, RMII1, RMII2, RXD1, + RXD2, RXD3, RXD4, SALT1, SALT10, SALT11, SALT12, SALT13, SALT14, + SALT2, SALT3, SALT4, SALT5, SALT6, SALT7, SALT8, SALT9, SCL1, + SCL2, SD1, SD2, SDA1, SDA2, SGPS1, SGPS2, SIOONCTRL, SIOPBI, + SIOPBO, SIOPWREQ, SIOPWRGD, SIOS3, SIOS5, SIOSCI, SPI1, SPI1CS1, + SPI1DEBUG, SPI1PASSTHRU, SPI2CK, SPI2CS0, SPI2CS1, SPI2MISO, + SPI2MOSI, TIMER3, TIMER4, TIMER5, TIMER6, TIMER7, TIMER8, TXD1, + TXD2, TXD3, TXD4, UART6, USB11BHID, USB2AD, USB2AH, USB2BD, + USB2BH, USBCKI, VGABIOSROM, VGAHS, VGAVS, VPI24, VPO, WDTRST1, + WDTRST2, ] + +required: + - compatible + - aspeed,external-nodes + +examples: + - | + apb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + syscon: scu@1e6e2000 { + compatible = "aspeed,ast2500-scu", "syscon", "simple-mfd"; + reg = <0x1e6e2000 0x1a8>; + + pinctrl: pinctrl { + compatible = "aspeed,g5-pinctrl"; + aspeed,external-nodes = <&gfx>, <&lhc>; + + pinctrl_i2c3_default: i2c3_default { + function = "I2C3"; + groups = "I2C3"; + }; + + pinctrl_gpioh0_unbiased_default: gpioh0 { + pins = "A18"; + bias-disable; + }; + }; + }; + + gfx: display@1e6e6000 { + compatible = "aspeed,ast2500-gfx", "syscon"; + reg = <0x1e6e6000 0x1000>; + }; + }; + + lpc: lpc@1e789000 { + compatible = "aspeed,ast2500-lpc", "simple-mfd"; + reg = <0x1e789000 0x1000>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x1e789000 0x1000>; + + lpc_host: lpc-host@80 { + compatible = "aspeed,ast2500-lpc-host", "simple-mfd", "syscon"; + reg = <0x80 0x1e0>; + reg-io-width = <4>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x80 0x1e0>; + + lhc: lhc@20 { + compatible = "aspeed,ast2500-lhc"; + reg = <0x20 0x24 0x48 0x8>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2600-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2600-pinctrl.yaml new file mode 100644 index 000000000000..f83d888176cc --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2600-pinctrl.yaml @@ -0,0 +1,115 @@ +# SPDX-License-Identifier: GPL-2.0+ +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ASPEED AST2600 Pin Controller + +maintainers: + - Andrew Jeffery <andrew@aj.id.au> + +description: |+ + The pin controller node should be the child of a syscon node with the + required property: + + - compatible: Should be one of the following: + "aspeed,ast2600-scu", "syscon", "simple-mfd" + + Refer to the the bindings described in + Documentation/devicetree/bindings/mfd/syscon.txt + +properties: + compatible: + const: aspeed,ast2600-pinctrl + +patternProperties: + '^.*$': + if: + type: object + then: + properties: + function: + allOf: + - $ref: "/schemas/types.yaml#/definitions/string" + - enum: [ ADC0, ADC1, ADC10, ADC11, ADC12, ADC13, ADC14, ADC15, + ADC2, ADC3, ADC4, ADC5, ADC6, ADC7, ADC8, ADC9, BMCINT, ESPI, + ESPIALT, FSI1, FSI2, FWSPIABR, FWSPID, FWSPIWP, GPIT0, GPIT1, + GPIT2, GPIT3, GPIT4, GPIT5, GPIT6, GPIT7, GPIU0, GPIU1, GPIU2, + GPIU3, GPIU4, GPIU5, GPIU6, GPIU7, I2C1, I2C10, I2C11, I2C12, + I2C13, I2C14, I2C15, I2C16, I2C2, I2C3, I2C4, I2C5, I2C6, I2C7, + I2C8, I2C9, I3C3, I3C4, I3C5, I3C6, JTAGM, LHPD, LHSIRQ, LPC, + LPCHC, LPCPD, LPCPME, LPCSMI, LSIRQ, MACLINK1, MACLINK2, + MACLINK3, MACLINK4, MDIO1, MDIO2, MDIO3, MDIO4, NCTS1, NCTS2, + NCTS3, NCTS4, NDCD1, NDCD2, NDCD3, NDCD4, NDSR1, NDSR2, NDSR3, + NDSR4, NDTR1, NDTR2, NDTR3, NDTR4, NRI1, NRI2, NRI3, NRI4, NRTS1, + NRTS2, NRTS3, NRTS4, OSCCLK, PEWAKE, PWM0, PWM1, PWM10, PWM11, + PWM12, PWM13, PWM14, PWM15, PWM2, PWM3, PWM4, PWM5, PWM6, PWM7, + PWM8, PWM9, RGMII1, RGMII2, RGMII3, RGMII4, RMII1, RMII2, RMII3, + RMII4, RXD1, RXD2, RXD3, RXD4, SALT1, SALT10, SALT11, SALT12, + SALT13, SALT14, SALT15, SALT16, SALT2, SALT3, SALT4, SALT5, + SALT6, SALT7, SALT8, SALT9, SD1, SD2, SD3, SD3DAT4, SD3DAT5, + SD3DAT6, SD3DAT7, SGPM1, SGPS1, SIOONCTRL, SIOPBI, SIOPBO, + SIOPWREQ, SIOPWRGD, SIOS3, SIOS5, SIOSCI, SPI1, SPI1ABR, SPI1CS1, + SPI1WP, SPI2, SPI2CS1, SPI2CS2, TACH0, TACH1, TACH10, TACH11, + TACH12, TACH13, TACH14, TACH15, TACH2, TACH3, TACH4, TACH5, + TACH6, TACH7, TACH8, TACH9, THRU0, THRU1, THRU2, THRU3, TXD1, + TXD2, TXD3, TXD4, UART10, UART11, UART12, UART13, UART6, UART7, + UART8, UART9, VB, VGAHS, VGAVS, WDTRST1, WDTRST2, WDTRST3, + WDTRST4, ] + groups: + allOf: + - $ref: "/schemas/types.yaml#/definitions/string" + - enum: [ ADC0, ADC1, ADC10, ADC11, ADC12, ADC13, ADC14, ADC15, + ADC2, ADC3, ADC4, ADC5, ADC6, ADC7, ADC8, ADC9, BMCINT, ESPI, + ESPIALT, FSI1, FSI2, FWSPIABR, FWSPID, FWQSPID, FWSPIWP, GPIT0, + GPIT1, GPIT2, GPIT3, GPIT4, GPIT5, GPIT6, GPIT7, GPIU0, GPIU1, + GPIU2, GPIU3, GPIU4, GPIU5, GPIU6, GPIU7, HVI3C3, HVI3C4, I2C1, + I2C10, I2C11, I2C12, I2C13, I2C14, I2C15, I2C16, I2C2, I2C3, + I2C4, I2C5, I2C6, I2C7, I2C8, I2C9, I3C3, I3C4, I3C5, I3C6, + JTAGM, LHPD, LHSIRQ, LPC, LPCHC, LPCPD, LPCPME, LPCSMI, LSIRQ, + MACLINK1, MACLINK2, MACLINK3, MACLINK4, MDIO1, MDIO2, MDIO3, + MDIO4, NCTS1, NCTS2, NCTS3, NCTS4, NDCD1, NDCD2, NDCD3, NDCD4, + NDSR1, NDSR2, NDSR3, NDSR4, NDTR1, NDTR2, NDTR3, NDTR4, NRI1, + NRI2, NRI3, NRI4, NRTS1, NRTS2, NRTS3, NRTS4, OSCCLK, PEWAKE, + PWM0, PWM1, PWM10G0, PWM10G1, PWM11G0, PWM11G1, PWM12G0, PWM12G1, + PWM13G0, PWM13G1, PWM14G0, PWM14G1, PWM15G0, PWM15G1, PWM2, PWM3, + PWM4, PWM5, PWM6, PWM7, PWM8G0, PWM8G1, PWM9G0, PWM9G1, QSPI1, + QSPI2, RGMII1, RGMII2, RGMII3, RGMII4, RMII1, RMII2, RMII3, + RMII4, RXD1, RXD2, RXD3, RXD4, SALT1, SALT10G0, SALT10G1, + SALT11G0, SALT11G1, SALT12G0, SALT12G1, SALT13G0, SALT13G1, + SALT14G0, SALT14G1, SALT15G0, SALT15G1, SALT16G0, SALT16G1, + SALT2, SALT3, SALT4, SALT5, SALT6, SALT7, SALT8, SALT9G0, + SALT9G1, SD1, SD2, SD3, SD3DAT4, SD3DAT5, SD3DAT6, SD3DAT7, + SGPM1, SGPS1, SIOONCTRL, SIOPBI, SIOPBO, SIOPWREQ, SIOPWRGD, + SIOS3, SIOS5, SIOSCI, SPI1, SPI1ABR, SPI1CS1, SPI1WP, SPI2, + SPI2CS1, SPI2CS2, TACH0, TACH1, TACH10, TACH11, TACH12, TACH13, + TACH14, TACH15, TACH2, TACH3, TACH4, TACH5, TACH6, TACH7, TACH8, + TACH9, THRU0, THRU1, THRU2, THRU3, TXD1, TXD2, TXD3, TXD4, + UART10, UART11, UART12G0, UART12G1, UART13G0, UART13G1, UART6, + UART7, UART8, UART9, VB, VGAHS, VGAVS, WDTRST1, WDTRST2, WDTRST3, + WDTRST4, ] + +required: + - compatible + +examples: + - | + syscon: scu@1e6e2000 { + compatible = "aspeed,ast2600-scu", "syscon", "simple-mfd"; + reg = <0x1e6e2000 0xf6c>; + + pinctrl: pinctrl { + compatible = "aspeed,g6-pinctrl"; + + pinctrl_pwm10g1_default: pwm10g1_default { + function = "PWM10"; + groups = "PWM10G1"; + }; + + pinctrl_gpioh0_unbiased_default: gpioh0 { + pins = "A18"; + bias-disable; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/bitmain,bm1880-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/bitmain,bm1880-pinctrl.txt index ed34bb1ee81c..4980776122cc 100644 --- a/Documentation/devicetree/bindings/pinctrl/bitmain,bm1880-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/bitmain,bm1880-pinctrl.txt @@ -14,7 +14,8 @@ phrase "pin configuration node". The pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration for BM1880 SoC -includes only pinmux as there is no pinconf support available in SoC. +includes pinmux and various pin configuration parameters, such as pull-up, +slew rate etc... Each configuration node can consist of multiple nodes describing the pinmux options. The name of each subnode is not important; all subnodes should be @@ -84,10 +85,37 @@ Required Properties: gpio66, gpio67, eth1, i2s0, i2s0_mclkin, i2s1, i2s1_mclkin, spi0 +Optional Properties: + +- bias-disable: No arguments. Disable pin bias. +- bias-pull-down: No arguments. The specified pins should be configured as + pull down. +- bias-pull-up: No arguments. The specified pins should be configured as + pull up. +- input-schmitt-enable: No arguments: Enable schmitt trigger for the specified + pins +- input-schmitt-disable: No arguments: Disable schmitt trigger for the specified + pins +- slew-rate: Integer. Sets slew rate for the specified pins. + Valid values are: + <0> - Slow + <1> - Fast +- drive-strength: Integer. Selects the drive strength for the specified + pins in mA. + Valid values are: + <4> + <8> + <12> + <16> + <20> + <24> + <28> + <32> + Example: - pinctrl: pinctrl@50 { + pinctrl: pinctrl@400 { compatible = "bitmain,bm1880-pinctrl"; - reg = <0x50 0x4B0>; + reg = <0x400 0x120>; pinctrl_uart0_default: uart0-default { pinmux { diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt b/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt index 3fac0a061bcc..3cab7336a326 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt @@ -5,6 +5,10 @@ controller, and pinmux/control device. Required properties: - compatible: "brcm,bcm2835-gpio" +- compatible: should be one of: + "brcm,bcm2835-gpio" - BCM2835 compatible pinctrl + "brcm,bcm7211-gpio" - BCM7211 compatible pinctrl + "brcm,bcm2711-gpio" - BCM2711 compatible pinctrl - reg: Should contain the physical address of the GPIO module's registers. - gpio-controller: Marks the device node as a GPIO controller. - #gpio-cells : Should be two. The first cell is the pin number and the diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.txt index 524a16fca666..e4e01c05cf83 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.txt @@ -12,7 +12,7 @@ Required properties in sub-nodes: - fsl,pins: each entry consists of 6 integers and represents the mux and config setting for one pin. The first 5 integers <mux_reg conf_reg input_reg mux_val input_val> are specified using a PIN_FUNC_ID macro, which can be found in - <dt-bindings/pinctrl/imx8mm-pinfunc.h>. The last integer CONFIG is + <arch/arm64/boot/dts/freescale/imx8mm-pinfunc.h>. The last integer CONFIG is the pad setting value like pull-up on this pin. Please refer to i.MX8M Mini Reference Manual for detailed CONFIG settings. diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx8mn-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mn-pinctrl.txt new file mode 100644 index 000000000000..330716c971b9 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mn-pinctrl.txt @@ -0,0 +1,39 @@ +* Freescale IMX8MN IOMUX Controller + +Please refer to fsl,imx-pinctrl.txt and pinctrl-bindings.txt in this directory +for common binding part and usage. + +Required properties: +- compatible: "fsl,imx8mn-iomuxc" +- reg: should contain the base physical address and size of the iomuxc + registers. + +Required properties in sub-nodes: +- fsl,pins: each entry consists of 6 integers and represents the mux and config + setting for one pin. The first 5 integers <mux_reg conf_reg input_reg mux_val + input_val> are specified using a PIN_FUNC_ID macro, which can be found in + <arch/arm64/boot/dts/freescale/imx8mn-pinfunc.h>. The last integer CONFIG is + the pad setting value like pull-up on this pin. Please refer to i.MX8M Nano + Reference Manual for detailed CONFIG settings. + +Examples: + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; +}; + +iomuxc: pinctrl@30330000 { + compatible = "fsl,imx8mn-iomuxc"; + reg = <0x0 0x30330000 0x0 0x10000>; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MN_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140 + MX8MN_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140 + MX8MN_IOMUXC_UART3_RXD_UART1_DCE_CTS_B 0x140 + MX8MN_IOMUXC_UART3_TXD_UART1_DCE_RTS_B 0x140 + MX8MN_IOMUXC_SD1_DATA4_GPIO2_IO6 0x19 + >; + }; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt index af20b0ec715c..0014d9899797 100644 --- a/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt @@ -1,18 +1,18 @@ -Ingenic jz47xx pin controller +Ingenic XBurst pin controller Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -For the jz47xx SoCs, pin control is tightly bound with GPIO ports. All pins may +For the XBurst SoCs, pin control is tightly bound with GPIO ports. All pins may be used as GPIOs, multiplexed device functions are configured within the GPIO port configuration registers and it is typical to refer to pins using the naming scheme "PxN" where x is a character identifying the GPIO port with which the pin is associated and N is an integer from 0 to 31 identifying the pin within that GPIO port. For example PA0 is the first pin in GPIO port A, and -PB31 is the last pin in GPIO port B. The jz4740 contains 4 GPIO ports, PA to -PD, for a total of 128 pins. The jz4780 contains 6 GPIO ports, PA to PF, for a -total of 192 pins. +PB31 is the last pin in GPIO port B. The jz4740 and the x1000 contains 4 GPIO +ports, PA to PD, for a total of 128 pins. The jz4760, the jz4770 and the jz4780 +contains 6 GPIO ports, PA to PF, for a total of 192 pins. Required properties: @@ -21,8 +21,13 @@ Required properties: - compatible: One of: - "ingenic,jz4740-pinctrl" - "ingenic,jz4725b-pinctrl" + - "ingenic,jz4760-pinctrl" + - "ingenic,jz4760b-pinctrl" - "ingenic,jz4770-pinctrl" - "ingenic,jz4780-pinctrl" + - "ingenic,x1000-pinctrl" + - "ingenic,x1000e-pinctrl" + - "ingenic,x1500-pinctrl" - reg: Address range of the pinctrl registers. @@ -31,8 +36,10 @@ Required properties for sub-nodes (GPIO chips): - compatible: Must contain one of: - "ingenic,jz4740-gpio" + - "ingenic,jz4760-gpio" - "ingenic,jz4770-gpio" - "ingenic,jz4780-gpio" + - "ingenic,x1000-gpio" - reg: The GPIO bank number. - interrupt-controller: Marks the device node as an interrupt controller. - interrupts: Interrupt specifier for the controllers interrupt. diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt index 6c0ea155b708..2932f171ee85 100644 --- a/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt @@ -6,8 +6,8 @@ part and usage. Required properties: - compatible: "marvell,88f6180-pinctrl", "marvell,88f6190-pinctrl", "marvell,88f6192-pinctrl", - "marvell,88f6281-pinctrl", "marvell,88f6282-pinctrl" - "marvell,98dx4122-pinctrl" + "marvell,88f6281-pinctrl", "marvell,88f6282-pinctrl", + "marvell,98dx4122-pinctrl", "marvell,98dx1135-pinctrl" - reg: register specifier of MPP registers This driver supports all kirkwood variants, i.e. 88f6180, 88f619x, and 88f628x. @@ -317,3 +317,43 @@ mpp44 44 gpio mpp45 45 gpio mpp49 49 gpio +* Marvell Poncat2 98dx1135 + +name pins functions +================================================================================ + +mpp0 0 gpio, nand(io2), spi(cs) +mpp1 1 gpo, nand(io3), spi(mosi) +mpp2 2 gpo, nand(io4), spi(sck) +mpp3 3 gpo, nand(io5), spi(miso) +mpp4 4 gpio, nand(io6), uart0(rxd) +mpp5 5 gpo, nand(io7), uart0(txd) +mpp6 6 sysrst(out) +mpp7 7 gpo, spi(cs) +mpp8 8 gpio, twsi0(sda), uart1(rts) +mpp9 9 gpio, twsi(sck), uart1(cts) +mpp10 10 gpo, uart0(txd) +mpp11 11 gpio, uart0(rxd) +mpp13 13 gpio, uart1(txd) +mpp14 14 gpio, uart1(rxd) +mpp15 15 gpio, uart0(rts) +mpp16 16 gpio, uart0(cts) +mpp17 17 gpio, nand(cle) +mpp18 18 gpo, nand(io0) +mpp19 19 gpo, nand(io1) +mpp20 20 gpio +mpp21 21 gpio +mpp22 22 gpio +mpp23 23 gpio +mpp24 24 gpio +mpp25 25 gpio +mpp26 26 gpio +mpp27 27 gpio +mpp28 28 gpio, nand(ren) +mpp29 29 gpio, nand(wen) +mpp30 30 gpio +mpp31 31 gpio +mpp32 32 gpio +mpp33 33 gpio +mpp34 34 gpio, nand(ale) +mpp35 35 gpio, nand(cen) diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt index a47dd990a8d3..10dc4f7176ca 100644 --- a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt @@ -47,9 +47,19 @@ Required properties for pinmux nodes are: Required properties for configuration nodes: - pins: a list of pin names -Configuration nodes support the generic properties "bias-disable", -"bias-pull-up" and "bias-pull-down", described in file -pinctrl-bindings.txt +Configuration nodes support the following generic properties, as +described in file pinctrl-bindings.txt: + - "bias-disable" + - "bias-pull-up" + - "bias-pull-down" + - "output-enable" + - "output-disable" + - "output-low" + - "output-high" + +Optional properties : + - drive-strength-microamp: Drive strength for the specified pins in uA. + This property is only valid for G12A and newer. === Example === diff --git a/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt index 29b72e303ebf..51efd2085113 100644 --- a/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt @@ -5,7 +5,7 @@ Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and pin controller, GPIO, and interrupt bindings. PIC32 'pin configuration node' is a node of a group of pins which can be -used for a specific device or function. This node represents configuraions of +used for a specific device or function. This node represents configurations of pins, optional function, and optional mux related configuration. Required properties for pin controller node: diff --git a/Documentation/devicetree/bindings/pinctrl/nuvoton,npcm7xx-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/nuvoton,npcm7xx-pinctrl.txt index 83f4bbac94bb..a1264cc8660d 100644 --- a/Documentation/devicetree/bindings/pinctrl/nuvoton,npcm7xx-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/nuvoton,npcm7xx-pinctrl.txt @@ -213,4 +213,4 @@ pinctrl: pinctrl@f0800000 { groups = "clkreq"; function = "clkreq"; }; -};
\ No newline at end of file +}; diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra194-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra194-pinmux.txt new file mode 100644 index 000000000000..8763f448c376 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra194-pinmux.txt @@ -0,0 +1,107 @@ +NVIDIA Tegra194 pinmux controller + +Required properties: +- compatible: "nvidia,tegra194-pinmux" +- reg: Should contain a list of base address and size pairs for: + - first entry: The APB_MISC_GP_*_PADCTRL registers (pad control) + - second entry: The PINMUX_AUX_* registers (pinmux) + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Tegra's pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, tristate, drive strength, etc. + +See the TRM to determine which properties and values apply to each pin/group. +Macro values for property values are defined in +include/dt-binding/pinctrl/pinctrl-tegra.h. + +Required subnode-properties: +- nvidia,pins : An array of strings. Each string contains the name of a pin or + group. Valid values for these names are listed below. + +Optional subnode-properties: +- nvidia,function: A string containing the name of the function to mux to the + pin or group. +- nvidia,pull: Integer, representing the pull-down/up to apply to the pin. + 0: none, 1: down, 2: up. +- nvidia,tristate: Integer. + 0: drive, 1: tristate. +- nvidia,enable-input: Integer. Enable the pin's input path. + enable :TEGRA_PIN_ENABLE and + disable or output only: TEGRA_PIN_DISABLE. +- nvidia,open-drain: Integer. + enable: TEGRA_PIN_ENABLE. + disable: TEGRA_PIN_DISABLE. +- nvidia,lock: Integer. Lock the pin configuration against further changes + until reset. + enable: TEGRA_PIN_ENABLE. + disable: TEGRA_PIN_DISABLE. +- nvidia,io-hv: Integer. Select high-voltage receivers. + normal: TEGRA_PIN_DISABLE + high: TEGRA_PIN_ENABLE +- nvidia,schmitt: Integer. Enables Schmitt Trigger on the input. + normal: TEGRA_PIN_DISABLE + high: TEGRA_PIN_ENABLE +- nvidia,drive-type: Integer. Valid range 0...3. +- nvidia,pull-down-strength: Integer. Controls drive strength. 0 is weakest. + The range of valid values depends on the pingroup. See "CAL_DRVDN" in the + Tegra TRM. +- nvidia,pull-up-strength: Integer. Controls drive strength. 0 is weakest. + The range of valid values depends on the pingroup. See "CAL_DRVUP" in the + Tegra TRM. + +Valid values for pin and group names (nvidia,pin) are: + + These correspond to Tegra PADCTL_* (pinmux) registers. + + Mux groups: + + These correspond to Tegra PADCTL_* (pinmux) registers. Any property + that exists in those registers may be set for the following pin names. + + pex_l5_clkreq_n_pgg0, pex_l5_rst_n_pgg1 + + Drive groups: + + These registers controls a single pin for which a mux group exists. + See the list above for the pin name to use when configuring the pinmux. + + pex_l5_clkreq_n_pgg0, pex_l5_rst_n_pgg1 + +Valid values for nvidia,functions are: + + pe5 + +Power Domain: + pex_l5_clkreq_n_pgg0 and pex_l5_rst_n_pgg1 are part of PCIE C5 power + partition. Client devices must enable this partition before accessing + these pins here. + + +Example: + + tegra_pinctrl: pinmux: pinmux@2430000 { + compatible = "nvidia,tegra194-pinmux"; + reg = <0x2430000 0x17000 + 0xc300000 0x4000>; + + pinctrl-names = "pex_rst"; + pinctrl-0 = <&pex_rst_c5_out_state>; + + pex_rst_c5_out_state: pex_rst_c5_out { + pex_rst { + nvidia,pins = "pex_l5_rst_n_pgg1"; + nvidia,schmitt = <TEGRA_PIN_DISABLE>; + nvidia,lpdr = <TEGRA_PIN_ENABLE>; + nvidia,enable-input = <TEGRA_PIN_DISABLE>; + nvidia,io-high-voltage = <TEGRA_PIN_ENABLE>; + nvidia,tristate = <TEGRA_PIN_DISABLE>; + nvidia,pull = <TEGRA_PIN_PULL_NONE>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt deleted file mode 100644 index 3b7266c7c438..000000000000 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt +++ /dev/null @@ -1,172 +0,0 @@ -====================== -Aspeed Pin Controllers -====================== - -The Aspeed SoCs vary in functionality inside a generation but have a common mux -device register layout. - -Required properties for g4: -- compatible : Should be one of the following: - "aspeed,ast2400-pinctrl" - "aspeed,g4-pinctrl" - -Required properties for g5: -- compatible : Should be one of the following: - "aspeed,ast2500-pinctrl" - "aspeed,g5-pinctrl" - -- aspeed,external-nodes: A cell of phandles to external controller nodes: - 0: compatible with "aspeed,ast2500-gfx", "syscon" - 1: compatible with "aspeed,ast2500-lhc", "syscon" - -The pin controller node should be the child of a syscon node with the required -property: - -- compatible : Should be one of the following: - "aspeed,ast2400-scu", "syscon", "simple-mfd" - "aspeed,g4-scu", "syscon", "simple-mfd" - "aspeed,ast2500-scu", "syscon", "simple-mfd" - "aspeed,g5-scu", "syscon", "simple-mfd" - -Refer to the the bindings described in -Documentation/devicetree/bindings/mfd/syscon.txt - -Subnode Format -============== - -The required properties of pinmux child nodes are: -- function: the mux function to select -- groups : the list of groups to select with this function - -Required properties of pinconf child nodes are: -- groups: A list of groups to select (either this or "pins" must be - specified) -- pins : A list of ball names as strings, eg "D14" (either this or "groups" - must be specified) - -Optional properties of pinconf child nodes are: -- bias-disable : disable any pin bias -- bias-pull-down: pull down the pin -- drive-strength: sink or source at most X mA - -Definitions are as specified in -Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt, with any -further limitations as described above. - -For pinmux, each mux function has only one associated pin group. Each group is -named by its function. The following values for the function and groups -properties are supported: - -aspeed,ast2400-pinctrl, aspeed,g4-pinctrl: - -ACPI ADC0 ADC1 ADC10 ADC11 ADC12 ADC13 ADC14 ADC15 ADC2 ADC3 ADC4 ADC5 ADC6 -ADC7 ADC8 ADC9 BMCINT DDCCLK DDCDAT EXTRST FLACK FLBUSY FLWP GPID GPID0 GPID2 -GPID4 GPID6 GPIE0 GPIE2 GPIE4 GPIE6 I2C10 I2C11 I2C12 I2C13 I2C14 I2C3 I2C4 -I2C5 I2C6 I2C7 I2C8 I2C9 LPCPD LPCPME LPCRST LPCSMI MAC1LINK MAC2LINK MDIO1 -MDIO2 NCTS1 NCTS2 NCTS3 NCTS4 NDCD1 NDCD2 NDCD3 NDCD4 NDSR1 NDSR2 NDSR3 NDSR4 -NDTR1 NDTR2 NDTR3 NDTR4 NDTS4 NRI1 NRI2 NRI3 NRI4 NRTS1 NRTS2 NRTS3 OSCCLK PWM0 -PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 RGMII1 RGMII2 RMII1 RMII2 ROM16 ROM8 ROMCS1 -ROMCS2 ROMCS3 ROMCS4 RXD1 RXD2 RXD3 RXD4 SALT1 SALT2 SALT3 SALT4 SD1 SD2 SGPMCK -SGPMI SGPMLD SGPMO SGPSCK SGPSI0 SGPSI1 SGPSLD SIOONCTRL SIOPBI SIOPBO SIOPWREQ -SIOPWRGD SIOS3 SIOS5 SIOSCI SPI1 SPI1DEBUG SPI1PASSTHRU SPICS1 TIMER3 TIMER4 -TIMER5 TIMER6 TIMER7 TIMER8 TXD1 TXD2 TXD3 TXD4 UART6 USB11D1 USB11H2 USB2D1 -USB2H1 USBCKI VGABIOS_ROM VGAHS VGAVS VPI18 VPI24 VPI30 VPO12 VPO24 WDTRST1 -WDTRST2 - -aspeed,ast2500-pinctrl, aspeed,g5-pinctrl: - -ACPI ADC0 ADC1 ADC10 ADC11 ADC12 ADC13 ADC14 ADC15 ADC2 ADC3 ADC4 ADC5 ADC6 -ADC7 ADC8 ADC9 BMCINT DDCCLK DDCDAT ESPI FWSPICS1 FWSPICS2 GPID0 GPID2 GPID4 -GPID6 GPIE0 GPIE2 GPIE4 GPIE6 I2C10 I2C11 I2C12 I2C13 I2C14 I2C3 I2C4 I2C5 I2C6 -I2C7 I2C8 I2C9 LAD0 LAD1 LAD2 LAD3 LCLK LFRAME LPCHC LPCPD LPCPLUS LPCPME -LPCRST LPCSMI LSIRQ MAC1LINK MAC2LINK MDIO1 MDIO2 NCTS1 NCTS2 NCTS3 NCTS4 NDCD1 -NDCD2 NDCD3 NDCD4 NDSR1 NDSR2 NDSR3 NDSR4 NDTR1 NDTR2 NDTR3 NDTR4 NRI1 NRI2 -NRI3 NRI4 NRTS1 NRTS2 NRTS3 NRTS4 OSCCLK PEWAKE PNOR PWM0 PWM1 PWM2 PWM3 PWM4 -PWM5 PWM6 PWM7 RGMII1 RGMII2 RMII1 RMII2 RXD1 RXD2 RXD3 RXD4 SALT1 SALT10 -SALT11 SALT12 SALT13 SALT14 SALT2 SALT3 SALT4 SALT5 SALT6 SALT7 SALT8 SALT9 -SCL1 SCL2 SD1 SD2 SDA1 SDA2 SGPS1 SGPS2 SIOONCTRL SIOPBI SIOPBO SIOPWREQ -SIOPWRGD SIOS3 SIOS5 SIOSCI SPI1 SPI1CS1 SPI1DEBUG SPI1PASSTHRU SPI2CK SPI2CS0 -SPI2CS1 SPI2MISO SPI2MOSI TIMER3 TIMER4 TIMER5 TIMER6 TIMER7 TIMER8 TXD1 TXD2 -TXD3 TXD4 UART6 USB11BHID USB2AD USB2AH USB2BD USB2BH USBCKI VGABIOSROM VGAHS -VGAVS VPI24 VPO WDTRST1 WDTRST2 - -Examples -======== - -g4 Example ----------- - -syscon: scu@1e6e2000 { - compatible = "aspeed,ast2400-scu", "syscon", "simple-mfd"; - reg = <0x1e6e2000 0x1a8>; - - pinctrl: pinctrl { - compatible = "aspeed,g4-pinctrl"; - - pinctrl_i2c3_default: i2c3_default { - function = "I2C3"; - groups = "I2C3"; - }; - - pinctrl_gpioh0_unbiased_default: gpioh0 { - pins = "A8"; - bias-disable; - }; - }; -}; - -g5 Example ----------- - -ahb { - apb { - syscon: scu@1e6e2000 { - compatible = "aspeed,ast2500-scu", "syscon", "simple-mfd"; - reg = <0x1e6e2000 0x1a8>; - - pinctrl: pinctrl { - compatible = "aspeed,g5-pinctrl"; - aspeed,external-nodes = <&gfx &lhc>; - - pinctrl_i2c3_default: i2c3_default { - function = "I2C3"; - groups = "I2C3"; - }; - - pinctrl_gpioh0_unbiased_default: gpioh0 { - pins = "A18"; - bias-disable; - }; - }; - }; - - gfx: display@1e6e6000 { - compatible = "aspeed,ast2500-gfx", "syscon"; - reg = <0x1e6e6000 0x1000>; - }; - }; - - lpc: lpc@1e789000 { - compatible = "aspeed,ast2500-lpc", "simple-mfd"; - reg = <0x1e789000 0x1000>; - - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x0 0x1e789000 0x1000>; - - lpc_host: lpc-host@80 { - compatible = "aspeed,ast2500-lpc-host", "simple-mfd", "syscon"; - reg = <0x80 0x1e0>; - reg-io-width = <4>; - - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x0 0x80 0x1e0>; - - lhc: lhc@20 { - compatible = "aspeed,ast2500-lhc"; - reg = <0x20 0x24 0x48 0x8>; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt index cef2b5855d60..fcd37e93ed4d 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt @@ -258,6 +258,7 @@ drive-push-pull - drive actively high and low drive-open-drain - drive with open drain drive-open-source - drive with open source drive-strength - sink or source at most X mA +drive-strength-microamp - sink or source at most X uA input-enable - enable input on pin (no effect on output, such as enabling an input buffer) input-disable - disable input on pin (no effect on output, such as @@ -326,6 +327,8 @@ arguments are described below. - drive-strength takes as argument the target strength in mA. +- drive-strength-microamp takes as argument the target strength in uA. + - input-debounce takes the debounce time in usec as argument or 0 to disable debouncing diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mcp23s08.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-mcp23s08.txt index 625a22e2f211..8b94aa8f5971 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mcp23s08.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mcp23s08.txt @@ -82,7 +82,7 @@ gpiom1: gpio@0 { compatible = "microchip,mcp23s17"; gpio-controller; #gpio-cells = <2>; - spi-present-mask = <0x01>; + microchip,spi-present-mask = <0x01>; reg = <0>; spi-max-frequency = <1000000>; }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt index 68e93d5b7ede..c9782397ff14 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt @@ -122,17 +122,17 @@ to specify in a pin configuration subnode: - bias-disable: Usage: optional Value type: <none> - Definition: The specified pins should be configued as no pull. + Definition: The specified pins should be configured as no pull. - bias-pull-down: Usage: optional Value type: <none> - Definition: The specified pins should be configued as pull down. + Definition: The specified pins should be configured as pull down. - bias-pull-up: Usage: optional Value type: <none> - Definition: The specified pins should be configued as pull up. + Definition: The specified pins should be configured as pull up. - output-high: Usage: optional diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.txt index 6dd72f8599e9..7b151894f5a0 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.txt @@ -118,17 +118,17 @@ to specify in a pin configuration subnode: - bias-disable: Usage: optional Value type: <none> - Definition: The specified pins should be configued as no pull. + Definition: The specified pins should be configured as no pull. - bias-pull-down: Usage: optional Value type: <none> - Definition: The specified pins should be configued as pull down. + Definition: The specified pins should be configured as pull down. - bias-pull-up: Usage: optional Value type: <none> - Definition: The specified pins should be configued as pull up. + Definition: The specified pins should be configured as pull up. - output-high: Usage: optional diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.txt index 86ecdcfc4fb8..d46973968873 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.txt @@ -97,17 +97,17 @@ to specify in a pin configuration subnode: - bias-disable: Usage: optional Value type: <none> - Definition: The specified pins should be configued as no pull. + Definition: The specified pins should be configured as no pull. - bias-pull-down: Usage: optional Value type: <none> - Definition: The specified pins should be configued as pull down. + Definition: The specified pins should be configured as pull down. - bias-pull-up: Usage: optional Value type: <none> - Definition: The specified pins should be configued as pull up. + Definition: The specified pins should be configured as pull up. - output-high: Usage: optional diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.txt index 195a7a0ef0cc..3354a63296d9 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.txt @@ -130,17 +130,17 @@ to specify in a pin configuration subnode: - bias-disable: Usage: optional Value type: <none> - Definition: The specified pins should be configued as no pull. + Definition: The specified pins should be configured as no pull. - bias-pull-down: Usage: optional Value type: <none> - Definition: The specified pins should be configued as pull down. + Definition: The specified pins should be configured as pull down. - bias-pull-up: Usage: optional Value type: <none> - Definition: The specified pins should be configued as pull up. + Definition: The specified pins should be configured as pull up. - output-high: Usage: optional diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt index 5034eb6653c7..a7dd213c77c6 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt @@ -124,17 +124,17 @@ to specify in a pin configuration subnode: - bias-disable: Usage: optional Value type: <none> - Definition: The specified pins should be configued as no pull. + Definition: The specified pins should be configured as no pull. - bias-pull-down: Usage: optional Value type: <none> - Definition: The specified pins should be configued as pull down. + Definition: The specified pins should be configured as pull down. - bias-pull-up: Usage: optional Value type: <none> - Definition: The specified pins should be configued as pull up. + Definition: The specified pins should be configured as pull up. - output-high: Usage: optional diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8994-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8994-pinctrl.txt index f15443f6e78e..da52df6273bc 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8994-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8994-pinctrl.txt @@ -128,17 +128,17 @@ to specify in a pin configuration subnode: - bias-disable: Usage: optional Value type: <none> - Definition: The specified pins should be configued as no pull. + Definition: The specified pins should be configured as no pull. - bias-pull-down: Usage: optional Value type: <none> - Definition: The specified pins should be configued as pull down. + Definition: The specified pins should be configured as pull down. - bias-pull-up: Usage: optional Value type: <none> - Definition: The specified pins should be configued as pull up. + Definition: The specified pins should be configured as pull up. - output-high: Usage: optional diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8996-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8996-pinctrl.txt index fa97f609fe45..a56cb882830c 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8996-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8996-pinctrl.txt @@ -149,17 +149,17 @@ to specify in a pin configuration subnode: - bias-disable: Usage: optional Value type: <none> - Definition: The specified pins should be configued as no pull. + Definition: The specified pins should be configured as no pull. - bias-pull-down: Usage: optional Value type: <none> - Definition: The specified pins should be configued as pull down. + Definition: The specified pins should be configured as pull down. - bias-pull-up: Usage: optional Value type: <none> - Definition: The specified pins should be configued as pull up. + Definition: The specified pins should be configured as pull up. - output-high: Usage: optional diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt index e70c79bbbc5b..c4de930f2406 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt @@ -40,6 +40,14 @@ MSM8998 platform. Definition: must be 2. Specifying the pin number and flags, as defined in <dt-bindings/gpio/gpio.h> +- gpio-ranges: + Usage: required + Definition: see ../gpio/gpio.txt + +- gpio-reserved-ranges: + Usage: optional + Definition: see ../gpio/gpio.txt + Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for a general description of GPIO and interrupt bindings. @@ -124,9 +132,8 @@ to specify in a pin configuration subnode: qlink_request, qua_mi2s, sd_card, sd_write, sdc40, sdc41, sdc42, sdc43, sdc4_clk, sdc4_cmd, sec_mi2s, sp_cmu, spkr_i2s, ssbi1, ssc_irq, ter_mi2s, tgu_ch0, tgu_ch1, - tsense_pwm1, tsense_pwm2, tsif1_clk, tsif1_data, tsif1_en, - tsif1_error, tsif1_sync, tsif2_clk, tsif2_data, tsif2_en, - tsif2_error, tsif2_sync, uim1_clk, uim1_data, uim1_present, + tsense_pwm1, tsense_pwm2, tsif0, tsif1, + uim1_clk, uim1_data, uim1_present, uim1_reset, uim2_clk, uim2_data, uim2_present, uim2_reset, uim_batt, usb_phy, vfr_1, vsense_clkout, vsense_data0, vsense_data1, vsense_mode, wlan1_adc0, wlan1_adc1, @@ -135,17 +142,17 @@ to specify in a pin configuration subnode: - bias-disable: Usage: optional Value type: <none> - Definition: The specified pins should be configued as no pull. + Definition: The specified pins should be configured as no pull. - bias-pull-down: Usage: optional Value type: <none> - Definition: The specified pins should be configued as pull down. + Definition: The specified pins should be configured as pull down. - bias-pull-up: Usage: optional Value type: <none> - Definition: The specified pins should be configued as pull up. + Definition: The specified pins should be configured as pull up. - output-high: Usage: optional @@ -175,6 +182,8 @@ Example: interrupts = <0 208 0>; gpio-controller; #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 0 175>; + gpio-reserved-ranges = <0 4>, <81 4>; interrupt-controller; #interrupt-cells = <2>; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt index 7f64a7e92c28..c32bf3237545 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt @@ -21,6 +21,8 @@ PMIC's from Qualcomm. "qcom,pmi8994-gpio" "qcom,pmi8998-gpio" "qcom,pms405-gpio" + "qcom,pm8150-gpio" + "qcom,pm8150b-gpio" And must contain either "qcom,spmi-gpio" or "qcom,ssbi-gpio" if the device is on an spmi bus or an ssbi bus respectively @@ -94,6 +96,10 @@ to specify in a pin configuration subnode: gpio1-gpio22 for pma8084 gpio1-gpio10 for pmi8994 gpio1-gpio12 for pms405 (holes on gpio1, gpio9 and gpio10) + gpio1-gpio10 for pm8150 (holes on gpio2, gpio5, gpio7 + and gpio8) + gpio1-gpio12 for pm8150b (holes on gpio3, gpio4, gpio7) + gpio1-gpio12 for pm8150l (hole on gpio7) - function: Usage: required diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.txt index 2b8f77762edc..a50e74684195 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.txt @@ -150,17 +150,17 @@ to specify in a pin configuration subnode: - bias-disable: Usage: optional Value type: <none> - Definition: The specified pins should be configued as no pull. + Definition: The specified pins should be configured as no pull. - bias-pull-down: Usage: optional Value type: <none> - Definition: The specified pins should be configued as pull down. + Definition: The specified pins should be configured as pull down. - bias-pull-up: Usage: optional Value type: <none> - Definition: The specified pins should be configued as pull up. + Definition: The specified pins should be configured as pull up. - output-high: Usage: optional diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sc7180-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,sc7180-pinctrl.txt new file mode 100644 index 000000000000..b5767ee82ee6 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sc7180-pinctrl.txt @@ -0,0 +1,186 @@ +Qualcomm Technologies, Inc. SC7180 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +SC7180 platform. + +- compatible: + Usage: required + Value type: <string> + Definition: must be "qcom,sc7180-pinctrl" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the north, south and west + TLMM tiles + +- reg-names: + Usage: required + Value type: <prop-encoded-array> + Definition: names for the cells of reg, must contain "north", "south" + and "west". + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: <none> + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/interrupt-controller/irq.h> + +- gpio-controller: + Usage: required + Value type: <none> + Definition: identifies this node as a gpio controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/gpio/gpio.h> + +- gpio-ranges: + Usage: required + Value type: <prop-encoded-array> + Definition: see ../gpio/gpio.txt + +- gpio-reserved-ranges: + Usage: optional + Value type: <prop-encoded-array> + Definition: see ../gpio/gpio.txt + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. + + Valid pins are: + gpio0-gpio118 + Supports mux, bias and drive-strength + + sdc1_clk, sdc1_cmd, sdc1_data sdc2_clk, sdc2_cmd, + sdc2_data sdc1_rclk + Supports bias and drive-strength + + ufs_reset + Supports bias and drive-strength + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Functions are only valid for gpio pins. + Valid values are: + + adsp_ext, agera_pll, aoss_cti, atest_char, atest_char0, + atest_char1, atest_char2, atest_char3, atest_tsens, + atest_tsens2, atest_usb1, atest_usb10, atest_usb11, + atest_usb12, atest_usb13, atest_usb2, atest_usb20, + atest_usb21, atest_usb22, atest_usb23, audio_ref, + btfm_slimbus, cam_mclk, cci_async, cci_i2c, cci_timer0, + cci_timer1, cci_timer2, cci_timer3, cci_timer4, + cri_trng, dbg_out, ddr_bist, ddr_pxi0, ddr_pxi1, + ddr_pxi2, ddr_pxi3, dp_hot, edp_lcd, gcc_gp1, gcc_gp2, + gcc_gp3, gpio, gp_pdm0, gp_pdm1, gp_pdm2, gps_tx, + jitter_bist, ldo_en, ldo_update, lpass_ext, mdp_vsync, + mdp_vsync0, mdp_vsync1, mdp_vsync2, mdp_vsync3, mi2s_0, + mi2s_1, mi2s_2, mss_lte, m_voc, pa_indicator, phase_flag, + PLL_BIST, pll_bypassnl, pll_reset, prng_rosc, qdss, + qdss_cti, qlink_enable, qlink_request, qspi_clk, qspi_cs, + qspi_data, qup00, qup01, qup02, qup03, qup04, qup05, + qup10, qup11, qup12, qup13, qup14, qup15, sdc1_tb, + sdc2_tb, sd_write, sp_cmu, tgu_ch0, tgu_ch1, tgu_ch2, + tgu_ch3, tsense_pwm1, tsense_pwm2, uim1, uim2, uim_batt, + usb_phy, vfr_1, _V_GPIO, _V_PPS_IN, _V_PPS_OUT, + vsense_trigger, wlan1_adc0, wlan1_adc1, wlan2_adc0, + wlan2_adc1, + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configured as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configured as pull down. + +- bias-pull-up: + Usage: optional + Value type: <none> + Definition: The specified pins should be configured as pull up. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + Not valid for sdc pins. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + Not valid for sdc pins. + +- drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + tlmm: pinctrl@3500000 { + compatible = "qcom,sc7180-pinctrl"; + reg = <0x3500000 0x300000>, + <0x3900000 0x300000>, + <0x3D00000 0x300000>; + reg-names = "west", "north", "south"; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 0 119>; + gpio-reserved-ranges = <0 4>, <106 4>; + interrupt-controller; + #interrupt-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt index 769ca83bb40d..be034d329e10 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt @@ -142,17 +142,17 @@ to specify in a pin configuration subnode: - bias-disable: Usage: optional Value type: <none> - Definition: The specified pins should be configued as no pull. + Definition: The specified pins should be configured as no pull. - bias-pull-down: Usage: optional Value type: <none> - Definition: The specified pins should be configued as pull down. + Definition: The specified pins should be configured as pull down. - bias-pull-up: Usage: optional Value type: <none> - Definition: The specified pins should be configued as pull up. + Definition: The specified pins should be configured as pull up. - output-high: Usage: optional diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.txt index 665aadb5ea28..7462e3743c68 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.txt @@ -79,7 +79,7 @@ to specify in a pin configuration subnode: gpio0-gpio149 Supports mux, bias and drive-strength - sdc2_clk, sdc2_cmd, sdc2_data + sdc2_clk, sdc2_cmd, sdc2_data, ufs_reset Supports bias and drive-strength - function: @@ -118,17 +118,17 @@ to specify in a pin configuration subnode: - bias-disable: Usage: optional Value type: <none> - Definition: The specified pins should be configued as no pull. + Definition: The specified pins should be configured as no pull. - bias-pull-down: Usage: optional Value type: <none> - Definition: The specified pins should be configued as pull down. + Definition: The specified pins should be configured as pull down. - bias-pull-up: Usage: optional Value type: <none> - Definition: The specified pins should be configued as pull up. + Definition: The specified pins should be configured as pull up. - output-high: Usage: optional diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm8150-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,sm8150-pinctrl.txt new file mode 100644 index 000000000000..fa37733e5102 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm8150-pinctrl.txt @@ -0,0 +1,190 @@ +Qualcomm SM8150 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +QCS404 platform. + +- compatible: + Usage: required + Value type: <string> + Definition: must be "qcom,sm8150-pinctrl" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the north, south, west + and east TLMM tiles. + +- reg-names: + Usage: required + Value type: <prop-encoded-array> + Defintiion: names for the cells of reg, must contain "north", "south" + "west" and "east". + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: <none> + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/interrupt-controller/irq.h> + +- gpio-controller: + Usage: required + Value type: <none> + Definition: identifies this node as a gpio controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/gpio/gpio.h> + +- gpio-ranges: + Usage: required + Value type: <prop-encoded-array> + Definition: see ../gpio/gpio.txt + +- gpio-reserved-ranges: + Usage: optional + Value type: <prop-encoded-array> + Definition: see ../gpio/gpio.txt + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. + + Valid pins are: + gpio0-gpio149 + Supports mux, bias and drive-strength + + sdc1_clk, sdc1_cmd, sdc1_data sdc2_clk, sdc2_cmd, + sdc2_data sdc1_rclk + Supports bias and drive-strength + + ufs_reset + Supports bias and drive-strength + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Functions are only valid for gpio pins. + Valid values are: + + adsp_ext, agera_pll, aoss_cti, ddr_pxi2, atest_char, + atest_char0, atest_char1, atest_char2, atest_char3, + audio_ref, atest_usb1, atest_usb2, atest_usb10, + atest_usb11, atest_usb12, atest_usb13, atest_usb20, + atest_usb21, atest_usb22, atest_usb2, atest_usb23, + btfm_slimbus, cam_mclk, cci_async, cci_i2c, cci_timer0, + cci_timer1, cci_timer2, cci_timer3, cci_timer4, + cri_trng, cri_trng0, cri_trng1, dbg_out, ddr_bist, + ddr_pxi0, ddr_pxi1, ddr_pxi3, edp_hot, edp_lcd, + emac_phy, emac_pps, gcc_gp1, gcc_gp2, gcc_gp3, gpio, + hs1_mi2s, hs2_mi2s, hs3_mi2s, jitter_bist, + lpass_slimbus, mdp_vsync, mdp_vsync0, mdp_vsync1, + mdp_vsync2, mdp_vsync3, mss_lte, m_voc, nav_pps, + pa_indicator, pci_e0, phase_flag, pll_bypassnl, + pll_bist, pci_e1, pll_reset, pri_mi2s, pri_mi2s_ws, + prng_rosc, qdss, qdss_cti, qlink_request, qlink_enable, + qspi0, qspi1, qspi2, qspi3, qspi_clk, qspi_cs, qua_mi2s, + qup0, qup1, qup2, qup3, qup4, qup5, qup6, qup7, qup8, + qup9, qup10, qup11, qup12, qup13, qup14, qup15, qup16, + qup17, qup18, qup19, qup_l4, qup_l5, qup_l6, rgmii, + sdc4, sd_write, sec_mi2s, spkr_i2s, sp_cmu, ter_mi2s, + tgu_ch0, tgu_ch1, tgu_ch2, tgu_ch3, tsense_pwm1, + tsense_pwm2, tsif1, tsif2, uim1, uim2, uim_batt, + usb2phy_ac, usb_phy, vfr_1, vsense_trigger, wlan1_adc0, + wlan1_adc1, wlan2_adc0, wlan2_adc1, wmss_reset + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull down. + +- bias-pull-up: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull up. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + Not valid for sdc pins. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + Not valid for sdc pins. + +- drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + tlmm: pinctrl@3000000 { + compatible = "qcom,sm8150-pinctrl"; + reg = <0x03100000 0x300000>, + <0x03500000 0x300000>, + <0x03900000 0x300000>, + <0x03D00000 0x300000>; + reg-names = "west", "east", "north", "south"; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 0 175>; + gpio-reserved-ranges = <0 4>, <126 4>; + interrupt-controller; + #interrupt-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt deleted file mode 100644 index 00169255e48c..000000000000 --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt +++ /dev/null @@ -1,208 +0,0 @@ -* STM32 GPIO and Pin Mux/Config controller - -STMicroelectronics's STM32 MCUs intregrate a GPIO and Pin mux/config hardware -controller. It controls the input/output settings on the available pins and -also provides ability to multiplex and configure the output of various on-chip -controllers onto these pads. - -Pin controller node: -Required properies: - - compatible: value should be one of the following: - "st,stm32f429-pinctrl" - "st,stm32f469-pinctrl" - "st,stm32f746-pinctrl" - "st,stm32f769-pinctrl" - "st,stm32h743-pinctrl" - "st,stm32mp157-pinctrl" - "st,stm32mp157-z-pinctrl" - - #address-cells: The value of this property must be 1 - - #size-cells : The value of this property must be 1 - - ranges : defines mapping between pin controller node (parent) to - gpio-bank node (children). - - pins-are-numbered: Specify the subnodes are using numbered pinmux to - specify pins. - -GPIO controller/bank node: -Required properties: - - gpio-controller : Indicates this device is a GPIO controller - - #gpio-cells : Should be two. - The first cell is the pin number - The second one is the polarity: - - 0 for active high - - 1 for active low - - reg : The gpio address range, relative to the pinctrl range - - clocks : clock that drives this bank - - st,bank-name : Should be a name string for this bank as specified in - the datasheet - -Optional properties: - - reset: : Reference to the reset controller - - st,syscfg: Should be phandle/offset/mask. - -The phandle to the syscon node which includes IRQ mux selection register. - -The offset of the IRQ mux selection register - -The field mask of IRQ mux, needed if different of 0xf. - - gpio-ranges: Define a dedicated mapping between a pin-controller and - a gpio controller. Format is <&phandle a b c> with: - -(phandle): phandle of pin-controller. - -(a): gpio base offset in range. - -(b): pin base offset in range. - -(c): gpio count in range - This entry has to be used either if there are holes inside a bank: - GPIOB0/B1/B2/B14/B15 (see example 2) - or if banks are not contiguous: - GPIOA/B/C/E... - NOTE: If "gpio-ranges" is used for a gpio controller, all gpio-controller - have to use a "gpio-ranges" entry. - More details in Documentation/devicetree/bindings/gpio/gpio.txt. - - st,bank-ioport: should correspond to the EXTI IOport selection (EXTI line - used to select GPIOs as interrupts). - - hwlocks: reference to a phandle of a hardware spinlock provider node. - - st,package: Indicates the SOC package used. - More details in include/dt-bindings/pinctrl/stm32-pinfunc.h - -Example 1: -#include <dt-bindings/pinctrl/stm32f429-pinfunc.h> -... - - pin-controller { - #address-cells = <1>; - #size-cells = <1>; - compatible = "st,stm32f429-pinctrl"; - ranges = <0 0x40020000 0x3000>; - pins-are-numbered; - - gpioa: gpio@40020000 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x0 0x400>; - resets = <&reset_ahb1 0>; - st,bank-name = "GPIOA"; - }; - ... - pin-functions nodes follow... - }; - -Example 2: -#include <dt-bindings/pinctrl/stm32f429-pinfunc.h> -... - - pinctrl: pin-controller { - #address-cells = <1>; - #size-cells = <1>; - compatible = "st,stm32f429-pinctrl"; - ranges = <0 0x40020000 0x3000>; - pins-are-numbered; - - gpioa: gpio@40020000 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x0 0x400>; - resets = <&reset_ahb1 0>; - st,bank-name = "GPIOA"; - gpio-ranges = <&pinctrl 0 0 16>; - }; - - gpiob: gpio@40020400 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x0 0x400>; - resets = <&reset_ahb1 0>; - st,bank-name = "GPIOB"; - ngpios = 4; - gpio-ranges = <&pinctrl 0 16 3>, - <&pinctrl 14 30 2>; - }; - - - ... - pin-functions nodes follow... - }; - - -Contents of function subnode node: ----------------------------------- -Subnode format -A pinctrl node should contain at least one subnode representing the -pinctrl group available on the machine. Each subnode will list the -pins it needs, and how they should be configured, with regard to muxer -configuration, pullups, drive, output high/low and output speed. - - node { - pinmux = <PIN_NUMBER_PINMUX>; - GENERIC_PINCONFIG; - }; - -Required properties: -- pinmux: integer array, represents gpio pin number and mux setting. - Supported pin number and mux varies for different SoCs, and are defined in - dt-bindings/pinctrl/<soc>-pinfunc.h directly. - These defines are calculated as: - ((port * 16 + line) << 8) | function - With: - - port: The gpio port index (PA = 0, PB = 1, ..., PK = 11) - - line: The line offset within the port (PA0 = 0, PA1 = 1, ..., PA15 = 15) - - function: The function number, can be: - * 0 : GPIO - * 1 : Alternate Function 0 - * 2 : Alternate Function 1 - * 3 : Alternate Function 2 - * ... - * 16 : Alternate Function 15 - * 17 : Analog - - To simplify the usage, macro is available to generate "pinmux" field. - This macro is available here: - - include/dt-bindings/pinctrl/stm32-pinfunc.h - - Some examples of using macro: - /* GPIO A9 set as alernate function 2 */ - ... { - pinmux = <STM32_PINMUX('A', 9, AF2)>; - }; - /* GPIO A9 set as GPIO */ - ... { - pinmux = <STM32_PINMUX('A', 9, GPIO)>; - }; - /* GPIO A9 set as analog */ - ... { - pinmux = <STM32_PINMUX('A', 9, ANALOG)>; - }; - -Optional properties: -- GENERIC_PINCONFIG: is the generic pinconfig options to use. - Available options are: - - bias-disable, - - bias-pull-down, - - bias-pull-up, - - drive-push-pull, - - drive-open-drain, - - output-low - - output-high - - slew-rate = <x>, with x being: - < 0 > : Low speed - < 1 > : Medium speed - < 2 > : Fast speed - < 3 > : High speed - -Example: - -pin-controller { -... - usart1_pins_a: usart1@0 { - pins1 { - pinmux = <STM32_PINMUX('A', 9, AF7)>; - bias-disable; - drive-push-pull; - slew-rate = <0>; - }; - pins2 { - pinmux = <STM32_PINMUX('A', 10, AF7)>; - bias-disable; - }; - }; -}; - -&usart1 { - pinctrl-0 = <&usart1_pins_a>; - pinctrl-names = "default"; -}; diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml new file mode 100644 index 000000000000..400df2da018a --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml @@ -0,0 +1,272 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (C) STMicroelectronics 2019. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/st,stm32-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STM32 GPIO and Pin Mux/Config controller + +maintainers: + - Alexandre TORGUE <alexandre.torgue@st.com> + +description: | + STMicroelectronics's STM32 MCUs intregrate a GPIO and Pin mux/config hardware + controller. It controls the input/output settings on the available pins and + also provides ability to multiplex and configure the output of various + on-chip controllers onto these pads. + +properties: + compatible: + enum: + - st,stm32f429-pinctrl + - st,stm32f469-pinctrl + - st,stm32f746-pinctrl + - st,stm32f769-pinctrl + - st,stm32h743-pinctrl + - st,stm32mp157-pinctrl + - st,stm32mp157-z-pinctrl + + '#address-cells': + const: 1 + '#size-cells': + const: 1 + + ranges: true + pins-are-numbered: true + hwlocks: true + + st,syscfg: + allOf: + - $ref: "/schemas/types.yaml#/definitions/phandle-array" + description: Should be phandle/offset/mask + items: + - description: Phandle to the syscon node which includes IRQ mux selection. + - description: The offset of the IRQ mux selection register. + - description: The field mask of IRQ mux, needed if different of 0xf. + + st,package: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [1, 2, 4, 8] + description: + Indicates the SOC package used. + More details in include/dt-bindings/pinctrl/stm32-pinfunc.h + + +patternProperties: + '^gpio@[0-9a-f]*$': + type: object + properties: + gpio-controller: true + '#gpio-cells': + const: 2 + + reg: + maxItems: 1 + clocks: + maxItems: 1 + reset: + minItems: 1 + maxItems: 1 + gpio-ranges: + minItems: 1 + maxItems: 16 + ngpios: + description: + Number of available gpios in a bank. + minimum: 1 + maximum: 16 + + st,bank-name: + allOf: + - $ref: "/schemas/types.yaml#/definitions/string" + - enum: + - GPIOA + - GPIOB + - GPIOC + - GPIOD + - GPIOE + - GPIOF + - GPIOG + - GPIOH + - GPIOI + - GPIOJ + - GPIOK + - GPIOZ + description: + Should be a name string for this bank as specified in the datasheet. + + st,bank-ioport: + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - minimum: 0 + - maximum: 11 + + description: + Should correspond to the EXTI IOport selection (EXTI line used + to select GPIOs as interrupts). + + required: + - gpio-controller + - '#gpio-cells' + - reg + - clocks + - st,bank-name + + '-[0-9]*$': + type: object + patternProperties: + '^pins': + type: object + description: | + A pinctrl node should contain at least one subnode representing the + pinctrl group available on the machine. Each subnode will list the + pins it needs, and how they should be configured, with regard to muxer + configuration, pullups, drive, output high/low and output speed. + properties: + pinmux: + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32-array" + description: | + Integer array, represents gpio pin number and mux setting. + Supported pin number and mux varies for different SoCs, and are + defined in dt-bindings/pinctrl/<soc>-pinfunc.h directly. + These defines are calculated as: ((port * 16 + line) << 8) | function + With: + - port: The gpio port index (PA = 0, PB = 1, ..., PK = 11) + - line: The line offset within the port (PA0 = 0, PA1 = 1, ..., PA15 = 15) + - function: The function number, can be: + * 0 : GPIO + * 1 : Alternate Function 0 + * 2 : Alternate Function 1 + * 3 : Alternate Function 2 + * ... + * 16 : Alternate Function 15 + * 17 : Analog + To simplify the usage, macro is available to generate "pinmux" field. + This macro is available here: + - include/dt-bindings/pinctrl/stm32-pinfunc.h + Some examples of using macro: + /* GPIO A9 set as alernate function 2 */ + ... { + pinmux = <STM32_PINMUX('A', 9, AF2)>; + }; + /* GPIO A9 set as GPIO */ + ... { + pinmux = <STM32_PINMUX('A', 9, GPIO)>; + }; + /* GPIO A9 set as analog */ + ... { + pinmux = <STM32_PINMUX('A', 9, ANALOG)>; + }; + + bias-disable: + type: boolean + bias-pull-down: + type: boolean + bias-pull-up: + type: boolean + drive-push-pull: + type: boolean + drive-open-drain: + type: boolean + output-low: + type: boolean + output-high: + type: boolean + slew-rate: + description: | + 0: Low speed + 1: Medium speed + 2: Fast speed + 3: High speed + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [0, 1, 2, 3] + + required: + - pinmux + +required: + - compatible + - '#address-cells' + - '#size-cells' + - ranges + - pins-are-numbered + +examples: + - | + #include <dt-bindings/pinctrl/stm32-pinfunc.h> + #include <dt-bindings/mfd/stm32f4-rcc.h> + //Example 1 + pinctrl@40020000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,stm32f429-pinctrl"; + ranges = <0 0x40020000 0x3000>; + pins-are-numbered; + + gpioa: gpio@0 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x0 0x400>; + resets = <&reset_ahb1 0>; + clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOA)>; + st,bank-name = "GPIOA"; + }; + }; + + //Example 2 (using gpio-ranges) + pinctrl@50020000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,stm32f429-pinctrl"; + ranges = <0 0x50020000 0x3000>; + pins-are-numbered; + + gpiob: gpio@1000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x1000 0x400>; + resets = <&reset_ahb1 0>; + clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOB)>; + st,bank-name = "GPIOB"; + gpio-ranges = <&pinctrl 0 0 16>; + }; + + gpioc: gpio@2000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x2000 0x400>; + resets = <&reset_ahb1 0>; + clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOC)>; + st,bank-name = "GPIOC"; + ngpios = <5>; + gpio-ranges = <&pinctrl 0 16 3>, + <&pinctrl 14 30 2>; + }; + }; + + //Example 3 pin groups + pinctrl@60020000 { + usart1_pins_a: usart1-0 { + pins1 { + pinmux = <STM32_PINMUX('A', 9, AF7)>; + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32_PINMUX('A', 10, AF7)>; + bias-disable; + }; + }; + }; + + usart1 { + pinctrl-0 = <&usart1_pins_a>; + pinctrl-names = "default"; + }; + +... diff --git a/Documentation/devicetree/bindings/power/amlogic,meson-ee-pwrc.yaml b/Documentation/devicetree/bindings/power/amlogic,meson-ee-pwrc.yaml new file mode 100644 index 000000000000..aab70e8b681e --- /dev/null +++ b/Documentation/devicetree/bindings/power/amlogic,meson-ee-pwrc.yaml @@ -0,0 +1,93 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 BayLibre, SAS +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/amlogic,meson-ee-pwrc.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Amlogic Meson Everything-Else Power Domains + +maintainers: + - Neil Armstrong <narmstrong@baylibre.com> + +description: |+ + The Everything-Else Power Domains node should be the child of a syscon + node with the required property: + + - compatible: Should be the following: + "amlogic,meson-gx-hhi-sysctrl", "simple-mfd", "syscon" + + Refer to the the bindings described in + Documentation/devicetree/bindings/mfd/syscon.txt + +properties: + compatible: + enum: + - amlogic,meson-g12a-pwrc + - amlogic,meson-sm1-pwrc + + clocks: + minItems: 2 + + clock-names: + items: + - const: vpu + - const: vapb + + resets: + minItems: 11 + + reset-names: + items: + - const: viu + - const: venc + - const: vcbus + - const: bt656 + - const: rdma + - const: venci + - const: vencp + - const: vdac + - const: vdi6 + - const: vencl + - const: vid_lock + + "#power-domain-cells": + const: 1 + + amlogic,ao-sysctrl: + description: phandle to the AO sysctrl node + allOf: + - $ref: /schemas/types.yaml#/definitions/phandle + +required: + - compatible + - clocks + - clock-names + - resets + - reset-names + - "#power-domain-cells" + - amlogic,ao-sysctrl + +examples: + - | + pwrc: power-controller { + compatible = "amlogic,meson-sm1-pwrc"; + #power-domain-cells = <1>; + amlogic,ao-sysctrl = <&rti>; + resets = <&reset_viu>, + <&reset_venc>, + <&reset_vcbus>, + <&reset_bt656>, + <&reset_rdma>, + <&reset_venci>, + <&reset_vencp>, + <&reset_vdac>, + <&reset_vdi6>, + <&reset_vencl>, + <&reset_vid_lock>; + reset-names = "viu", "venc", "vcbus", "bt656", + "rdma", "venci", "vencp", "vdac", + "vdi6", "vencl", "vid_lock"; + clocks = <&clk_vpu>, <&clk_vapb>; + clock-names = "vpu", "vapb"; + }; diff --git a/Documentation/devicetree/bindings/power/qcom,rpmpd.txt b/Documentation/devicetree/bindings/power/qcom,rpmpd.txt index 980e5413d18f..eb35b22f9e23 100644 --- a/Documentation/devicetree/bindings/power/qcom,rpmpd.txt +++ b/Documentation/devicetree/bindings/power/qcom,rpmpd.txt @@ -6,6 +6,8 @@ which then translates it into a corresponding voltage on a rail Required Properties: - compatible: Should be one of the following * qcom,msm8996-rpmpd: RPM Power domain for the msm8996 family of SoC + * qcom,msm8998-rpmpd: RPM Power domain for the msm8998 family of SoC + * qcom,qcs404-rpmpd: RPM Power domain for the qcs404 family of SoC * qcom,sdm845-rpmhpd: RPMh Power domain for the sdm845 family of SoC - #power-domain-cells: number of cells in Power domain specifier must be 1. diff --git a/Documentation/devicetree/bindings/power/reset/mt6323-poweroff.txt b/Documentation/devicetree/bindings/power/reset/mt6323-poweroff.txt new file mode 100644 index 000000000000..933f0c48e887 --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/mt6323-poweroff.txt @@ -0,0 +1,20 @@ +Device Tree Bindings for Power Controller on MediaTek PMIC + +The power controller which could be found on PMIC is responsible for externally +powering off or on the remote MediaTek SoC through the circuit BBPU. + +Required properties: +- compatible: Should be one of follows + "mediatek,mt6323-pwrc": for MT6323 PMIC + +Example: + + pmic { + compatible = "mediatek,mt6323"; + + ... + + power-controller { + compatible = "mediatek,mt6323-pwrc"; + }; + } diff --git a/Documentation/devicetree/bindings/power/reset/nvmem-reboot-mode.txt b/Documentation/devicetree/bindings/power/reset/nvmem-reboot-mode.txt new file mode 100644 index 000000000000..752d6126d5da --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/nvmem-reboot-mode.txt @@ -0,0 +1,26 @@ +NVMEM reboot mode driver + +This driver gets reboot mode magic value from reboot-mode driver +and stores it in a NVMEM cell named "reboot-mode". Then the bootloader +can read it and take different action according to the magic +value stored. + +Required properties: +- compatible: should be "nvmem-reboot-mode". +- nvmem-cells: A phandle to the reboot mode provided by a nvmem device. +- nvmem-cell-names: Should be "reboot-mode". + +The rest of the properties should follow the generic reboot-mode description +found in reboot-mode.txt + +Example: + reboot-mode { + compatible = "nvmem-reboot-mode"; + nvmem-cells = <&reboot_mode>; + nvmem-cell-names = "reboot-mode"; + + mode-normal = <0xAAAA5501>; + mode-bootloader = <0xBBBB5500>; + mode-recovery = <0xCCCC5502>; + mode-test = <0xDDDD5503>; + }; diff --git a/Documentation/devicetree/bindings/power/reset/qcom,pon.txt b/Documentation/devicetree/bindings/power/reset/qcom,pon.txt index 5705f575862d..0c0dc3a1e693 100644 --- a/Documentation/devicetree/bindings/power/reset/qcom,pon.txt +++ b/Documentation/devicetree/bindings/power/reset/qcom,pon.txt @@ -9,6 +9,7 @@ Required Properties: -compatible: Must be one of: "qcom,pm8916-pon" "qcom,pms405-pon" + "qcom,pm8998-pon" -reg: Specifies the physical address of the pon register diff --git a/Documentation/devicetree/bindings/property-units.txt b/Documentation/devicetree/bindings/property-units.txt index bfd33734faca..e9b8360b3288 100644 --- a/Documentation/devicetree/bindings/property-units.txt +++ b/Documentation/devicetree/bindings/property-units.txt @@ -12,32 +12,32 @@ unit prefixes. Time/Frequency ---------------------------------------- -mhz : megahertz --hz : Hertz (preferred) --sec : seconds --ms : milliseconds --us : microseconds --ns : nanoseconds +-hz : hertz (preferred) +-sec : second +-ms : millisecond +-us : microsecond +-ns : nanosecond Distance ---------------------------------------- --mm : millimeters +-mm : millimeter Electricity ---------------------------------------- --microamp : micro amps --microamp-hours : micro amp-hours --ohms : Ohms --micro-ohms : micro Ohms --microwatt-hours: micro Watt-hours --microvolt : micro volts --picofarads : picofarads --femtofarads : femtofarads +-microamp : microampere +-microamp-hours : microampere hour +-ohms : ohm +-micro-ohms : microohm +-microwatt-hours: microwatt hour +-microvolt : microvolt +-picofarads : picofarad +-femtofarads : femtofarad Temperature ---------------------------------------- --celsius : Degrees Celsius --millicelsius : Degreee milli-Celsius +-celsius : degree Celsius +-millicelsius : millidegree Celsius Pressure ---------------------------------------- --kpascal : kiloPascal +-kpascal : kilopascal diff --git a/Documentation/devicetree/bindings/ptp/ptp-qoriq.txt b/Documentation/devicetree/bindings/ptp/ptp-qoriq.txt index 454c937076a2..d48f9eb3636e 100644 --- a/Documentation/devicetree/bindings/ptp/ptp-qoriq.txt +++ b/Documentation/devicetree/bindings/ptp/ptp-qoriq.txt @@ -4,6 +4,8 @@ General Properties: - compatible Should be "fsl,etsec-ptp" for eTSEC Should be "fsl,fman-ptp-timer" for DPAA FMan + Should be "fsl,dpaa2-ptp" for DPAA2 + Should be "fsl,enetc-ptp" for ENETC - reg Offset and length of the register set for the device - interrupts There should be at least two interrupts. Some devices have as many as four PTP related interrupts. diff --git a/Documentation/devicetree/bindings/pwm/allwinner,sun4i-a10-pwm.yaml b/Documentation/devicetree/bindings/pwm/allwinner,sun4i-a10-pwm.yaml new file mode 100644 index 000000000000..0ac52f83a58c --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/allwinner,sun4i-a10-pwm.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pwm/allwinner,sun4i-a10-pwm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 PWM Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + "#pwm-cells": + const: 3 + + compatible: + oneOf: + - const: allwinner,sun4i-a10-pwm + - const: allwinner,sun5i-a10s-pwm + - const: allwinner,sun5i-a13-pwm + - const: allwinner,sun7i-a20-pwm + - const: allwinner,sun8i-h3-pwm + - items: + - const: allwinner,sun8i-a83t-pwm + - const: allwinner,sun8i-h3-pwm + - items: + - const: allwinner,sun50i-a64-pwm + - const: allwinner,sun5i-a13-pwm + - items: + - const: allwinner,sun50i-h5-pwm + - const: allwinner,sun5i-a13-pwm + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + +required: + - "#pwm-cells" + - compatible + - reg + - clocks + +additionalProperties: false + +examples: + - | + pwm: pwm@1c20e00 { + compatible = "allwinner,sun7i-a20-pwm"; + reg = <0x01c20e00 0xc>; + clocks = <&osc24M>; + #pwm-cells = <3>; + }; + +... diff --git a/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt b/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt deleted file mode 100644 index 7d9d3f90641b..000000000000 --- a/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt +++ /dev/null @@ -1,25 +0,0 @@ -Ingenic JZ47xx PWM Controller -============================= - -Required properties: -- compatible: One of: - * "ingenic,jz4740-pwm" - * "ingenic,jz4770-pwm" - * "ingenic,jz4780-pwm" -- #pwm-cells: Should be 3. See pwm.txt in this directory for a description - of the cells format. -- clocks : phandle to the external clock. -- clock-names : Should be "ext". - - -Example: - - pwm: pwm@10002000 { - compatible = "ingenic,jz4740-pwm"; - reg = <0x10002000 0x1000>; - - #pwm-cells = <3>; - - clocks = <&ext>; - clock-names = "ext"; - }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt b/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt index 991728cb46cb..c8501530173c 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt @@ -6,6 +6,8 @@ Required properties: - "mediatek,mt7622-pwm": found on mt7622 SoC. - "mediatek,mt7623-pwm": found on mt7623 SoC. - "mediatek,mt7628-pwm": found on mt7628 SoC. + - "mediatek,mt7629-pwm", "mediatek,mt7622-pwm": found on mt7629 SoC. + - "mediatek,mt8516-pwm": found on mt8516 SoC. - reg: physical base address and length of the controller's registers. - #pwm-cells: must be 2. See pwm.txt in this directory for a description of the cell format. diff --git a/Documentation/devicetree/bindings/pwm/pwm-sifive.txt b/Documentation/devicetree/bindings/pwm/pwm-sifive.txt new file mode 100644 index 000000000000..36447e3c9378 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-sifive.txt @@ -0,0 +1,33 @@ +SiFive PWM controller + +Unlike most other PWM controllers, the SiFive PWM controller currently only +supports one period for all channels in the PWM. All PWMs need to run at +the same period. The period also has significant restrictions on the values +it can achieve, which the driver rounds to the nearest achievable period. +PWM RTL that corresponds to the IP block version numbers can be found +here: + +https://github.com/sifive/sifive-blocks/tree/master/src/main/scala/devices/pwm + +Required properties: +- compatible: Should be "sifive,<chip>-pwm" and "sifive,pwm<version>". + Supported compatible strings are: "sifive,fu540-c000-pwm" for the SiFive + PWM v0 as integrated onto the SiFive FU540 chip, and "sifive,pwm0" for the + SiFive PWM v0 IP block with no chip integration tweaks. + Please refer to sifive-blocks-ip-versioning.txt for details. +- reg: physical base address and length of the controller's registers +- clocks: Should contain a clock identifier for the PWM's parent clock. +- #pwm-cells: Should be 3. See pwm.txt in this directory + for a description of the cell format. +- interrupts: one interrupt per PWM channel + +Examples: + +pwm: pwm@10020000 { + compatible = "sifive,fu540-c000-pwm", "sifive,pwm0"; + reg = <0x0 0x10020000 0x0 0x1000>; + clocks = <&tlclk>; + interrupt-parent = <&plic>; + interrupts = <42 43 44 45>; + #pwm-cells = <3>; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-sprd.txt b/Documentation/devicetree/bindings/pwm/pwm-sprd.txt new file mode 100644 index 000000000000..16fa5a096206 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-sprd.txt @@ -0,0 +1,40 @@ +Spreadtrum PWM controller + +Spreadtrum SoCs PWM controller provides 4 PWM channels. + +Required properties: +- compatible : Should be "sprd,ums512-pwm". +- reg: Physical base address and length of the controller's registers. +- clocks: The phandle and specifier referencing the controller's clocks. +- clock-names: Should contain following entries: + "pwmn": used to derive the functional clock for PWM channel n (n range: 0 ~ 3). + "enablen": for PWM channel n enable clock (n range: 0 ~ 3). +- #pwm-cells: Should be 2. See pwm.txt in this directory for a description of + the cells format. + +Optional properties: +- assigned-clocks: Reference to the PWM clock entries. +- assigned-clock-parents: The phandle of the parent clock of PWM clock. + +Example: + pwms: pwm@32260000 { + compatible = "sprd,ums512-pwm"; + reg = <0 0x32260000 0 0x10000>; + clock-names = "pwm0", "enable0", + "pwm1", "enable1", + "pwm2", "enable2", + "pwm3", "enable3"; + clocks = <&aon_clk CLK_PWM0>, <&aonapb_gate CLK_PWM0_EB>, + <&aon_clk CLK_PWM1>, <&aonapb_gate CLK_PWM1_EB>, + <&aon_clk CLK_PWM2>, <&aonapb_gate CLK_PWM2_EB>, + <&aon_clk CLK_PWM3>, <&aonapb_gate CLK_PWM3_EB>; + assigned-clocks = <&aon_clk CLK_PWM0>, + <&aon_clk CLK_PWM1>, + <&aon_clk CLK_PWM2>, + <&aon_clk CLK_PWM3>; + assigned-clock-parents = <&ext_26m>, + <&ext_26m>, + <&ext_26m>, + <&ext_26m>; + #pwm-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt b/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt index bd23302e84be..6521bc44a74e 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt @@ -11,8 +11,10 @@ Required parameters: bindings defined in pwm.txt. Optional properties: -- pinctrl-names: Set to "default". -- pinctrl-0: Phandle pointing to pin configuration node for PWM. +- pinctrl-names: Set to "default". An additional "sleep" state can be + defined to set pins in sleep state when in low power. +- pinctrl-n: Phandle(s) pointing to pin configuration node for PWM, + respectively for "default" and "sleep" states. Example: timer@40002400 { @@ -21,7 +23,8 @@ Example: pwm { compatible = "st,stm32-pwm-lp"; #pwm-cells = <3>; - pinctrl-names = "default"; + pinctrl-names = "default", "sleep"; pinctrl-0 = <&lppwm1_pins>; + pinctrl-1 = <&lppwm1_sleep_pins>; }; }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-stm32.txt b/Documentation/devicetree/bindings/pwm/pwm-stm32.txt index 3e6d55018d7a..a8690bfa5e1f 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-stm32.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-stm32.txt @@ -8,6 +8,8 @@ Required parameters: - pinctrl-names: Set to "default". - pinctrl-0: List of phandles pointing to pin configuration nodes for PWM module. For Pinctrl properties see ../pinctrl/pinctrl-bindings.txt +- #pwm-cells: Should be set to 3. This PWM chip uses the default 3 cells + bindings defined in pwm.txt. Optional parameters: - st,breakinput: One or two <index level filter> to describe break input configurations. @@ -28,6 +30,7 @@ Example: pwm { compatible = "st,stm32-pwm"; + #pwm-cells = <3>; pinctrl-0 = <&pwm1_pins>; pinctrl-names = "default"; st,breakinput = <0 1 5>; diff --git a/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt b/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt deleted file mode 100644 index 2a1affbff45e..000000000000 --- a/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt +++ /dev/null @@ -1,24 +0,0 @@ -Allwinner sun4i and sun7i SoC PWM controller - -Required properties: - - compatible: should be one of: - - "allwinner,sun4i-a10-pwm" - - "allwinner,sun5i-a10s-pwm" - - "allwinner,sun5i-a13-pwm" - - "allwinner,sun7i-a20-pwm" - - "allwinner,sun8i-h3-pwm" - - "allwinner,sun50i-a64-pwm", "allwinner,sun5i-a13-pwm" - - "allwinner,sun50i-h5-pwm", "allwinner,sun5i-a13-pwm" - - reg: physical base address and length of the controller's registers - - #pwm-cells: should be 3. See pwm.txt in this directory for a description of - the cells format. - - clocks: From common clock binding, handle to the parent clock. - -Example: - - pwm: pwm@1c20e00 { - compatible = "allwinner,sun7i-a20-pwm"; - reg = <0x01c20e00 0xc>; - clocks = <&osc24M>; - #pwm-cells = <3>; - }; diff --git a/Documentation/devicetree/bindings/regulator/act8865-regulator.txt b/Documentation/devicetree/bindings/regulator/act8865-regulator.txt index 3ae9f1088845..b9f58e480349 100644 --- a/Documentation/devicetree/bindings/regulator/act8865-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/act8865-regulator.txt @@ -34,6 +34,9 @@ Optional input supply properties: - inl67-supply: The input supply for LDO_REG3 and LDO_REG4 Any standard regulator properties can be used to configure the single regulator. +regulator-initial-mode, regulator-allowed-modes and regulator-mode could be specified +for act8865 using mode values from dt-bindings/regulator/active-semi,8865-regulator.h +file. The valid names for regulators are: - for act8846: @@ -47,6 +50,8 @@ The valid names for regulators are: Example: -------- +#include <dt-bindings/regulator/active-semi,8865-regulator.h> + i2c1: i2c@f0018000 { pmic: act8865@5b { compatible = "active-semi,act8865"; @@ -65,9 +70,19 @@ Example: regulator-name = "VCC_1V2"; regulator-min-microvolt = <1100000>; regulator-max-microvolt = <1300000>; - regulator-suspend-mem-microvolt = <1150000>; - regulator-suspend-standby-microvolt = <1150000>; regulator-always-on; + + regulator-allowed-modes = <ACT8865_REGULATOR_MODE_FIXED>, + <ACT8865_REGULATOR_MODE_LOWPOWER>; + regulator-initial-mode = <ACT8865_REGULATOR_MODE_FIXED>; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-min-microvolt = <1150000>; + regulator-suspend-max-microvolt = <1150000>; + regulator-changeable-in-suspend; + regulator-mode = <ACT8865_REGULATOR_MODE_LOWPOWER>; + }; }; vcc_3v3_reg: DCDC_REG3 { @@ -82,6 +97,14 @@ Example: regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; regulator-always-on; + + regulator-allowed-modes = <ACT8865_REGULATOR_MODE_NORMAL>, + <ACT8865_REGULATOR_MODE_LOWPOWER>; + regulator-initial-mode = <ACT8865_REGULATOR_MODE_NORMAL>; + + regulator-state-mem { + regulator-off-in-suspend; + }; }; vddfuse_reg: LDO_REG2 { diff --git a/Documentation/devicetree/bindings/regulator/arizona-regulator.txt b/Documentation/devicetree/bindings/regulator/arizona-regulator.txt index 443564d7784f..69bf41949b01 100644 --- a/Documentation/devicetree/bindings/regulator/arizona-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/arizona-regulator.txt @@ -5,7 +5,8 @@ of analogue I/O. This document lists regulator specific bindings, see the primary binding document: - ../mfd/arizona.txt + For Wolfson Microelectronic Arizona codecs: ../mfd/arizona.txt + For Cirrus Logic Madera codecs: ../mfd/madera.txt Optional properties: - wlf,ldoena : GPIO specifier for the GPIO controlling LDOENA diff --git a/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml b/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml index d289c2f7455a..a78150c47aa2 100644 --- a/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml +++ b/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml @@ -12,13 +12,26 @@ maintainers: description: Any property defined as part of the core regulator binding, defined in - regulator.txt, can also be used. However a fixed voltage regulator is + regulator.yaml, can also be used. However a fixed voltage regulator is expected to have the regulator-min-microvolt and regulator-max-microvolt to be the same. +allOf: + - $ref: "regulator.yaml#" + +if: + properties: + compatible: + contains: + const: regulator-fixed-clock + required: + - clocks + properties: compatible: - const: regulator-fixed + enum: + - const: regulator-fixed + - const: regulator-fixed-clock regulator-name: true @@ -26,6 +39,13 @@ properties: description: gpio to use for enable control maxItems: 1 + clocks: + description: + clock to use for enable control. This binding is only available if + the compatible is chosen to regulator-fixed-clock. The clock binding + is mandatory if compatible is chosen to regulator-fixed-clock. + maxItems: 1 + startup-delay-us: description: startup time in microseconds $ref: /schemas/types.yaml#/definitions/uint32 diff --git a/Documentation/devicetree/bindings/regulator/gpio-regulator.txt b/Documentation/devicetree/bindings/regulator/gpio-regulator.txt deleted file mode 100644 index dd25e73b5d79..000000000000 --- a/Documentation/devicetree/bindings/regulator/gpio-regulator.txt +++ /dev/null @@ -1,57 +0,0 @@ -GPIO controlled regulators - -Required properties: -- compatible : Must be "regulator-gpio". -- regulator-name : Defined in regulator.txt as optional, but required - here. -- gpios : Array of one or more GPIO pins used to select the - regulator voltage/current listed in "states". -- states : Selection of available voltages/currents provided by - this regulator and matching GPIO configurations to - achieve them. If there are no states in the "states" - array, use a fixed regulator instead. - -Optional properties: -- enable-gpios : GPIO used to enable/disable the regulator. - Warning, the GPIO phandle flags are ignored and the - GPIO polarity is controlled solely by the presence - of "enable-active-high" DT property. This is due to - compatibility with old DTs. -- enable-active-high : Polarity of "enable-gpio" GPIO is active HIGH. - Default is active LOW. -- gpios-states : On operating systems, that don't support reading back - gpio values in output mode (most notably linux), this - array provides the state of GPIO pins set when - requesting them from the gpio controller. Systems, - that are capable of preserving state when requesting - the lines, are free to ignore this property. - 0: LOW, 1: HIGH. Default is LOW if nothing else - is specified. -- startup-delay-us : Startup time in microseconds. -- regulator-type : Specifies what is being regulated, must be either - "voltage" or "current", defaults to voltage. - -Any property defined as part of the core regulator binding defined in -regulator.txt can also be used. - -Example: - - mmciv: gpio-regulator { - compatible = "regulator-gpio"; - - regulator-name = "mmci-gpio-supply"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <2600000>; - regulator-boot-on; - - enable-gpios = <&gpio0 23 0x4>; - gpios = <&gpio0 24 0x4 - &gpio0 25 0x4>; - states = <1800000 0x3 - 2200000 0x2 - 2600000 0x1 - 2900000 0x0>; - - startup-delay-us = <100000>; - enable-active-high; - }; diff --git a/Documentation/devicetree/bindings/regulator/gpio-regulator.yaml b/Documentation/devicetree/bindings/regulator/gpio-regulator.yaml new file mode 100644 index 000000000000..9d3b28417fb6 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/gpio-regulator.yaml @@ -0,0 +1,118 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/gpio-regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: GPIO controlled regulators + +maintainers: + - Liam Girdwood <lgirdwood@gmail.com> + - Mark Brown <broonie@kernel.org> + +description: + Any property defined as part of the core regulator binding, defined in + regulator.txt, can also be used. + +allOf: + - $ref: "regulator.yaml#" + +properties: + compatible: + const: regulator-gpio + + regulator-name: true + + enable-gpios: + description: GPIO to use to enable/disable the regulator. + Warning, the GPIO phandle flags are ignored and the GPIO polarity is + controlled solely by the presence of "enable-active-high" DT property. + This is due to compatibility with old DTs. + maxItems: 1 + + gpios: + description: Array of one or more GPIO pins used to select the regulator + voltage/current listed in "states". + minItems: 1 + maxItems: 8 # Should be enough... + + gpios-states: + description: | + On operating systems, that don't support reading back gpio values in + output mode (most notably linux), this array provides the state of GPIO + pins set when requesting them from the gpio controller. Systems, that are + capable of preserving state when requesting the lines, are free to ignore + this property. + 0: LOW + 1: HIGH + Default is LOW if nothing else is specified. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + - maxItems: 8 + items: + enum: [ 0, 1 ] + default: 0 + + states: + description: Selection of available voltages/currents provided by this + regulator and matching GPIO configurations to achieve them. If there are + no states in the "states" array, use a fixed regulator instead. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-matrix + - maxItems: 8 + items: + items: + - description: Voltage in microvolts + - description: GPIO group state value + + startup-delay-us: + description: startup time in microseconds + + enable-active-high: + description: Polarity of "enable-gpio" GPIO is active HIGH. Default is + active LOW. + type: boolean + + gpio-open-drain: + description: + GPIO is open drain type. If this property is missing then default + assumption is false. + type: boolean + + regulator-type: + description: Specifies what is being regulated. + allOf: + - $ref: /schemas/types.yaml#/definitions/string + - enum: + - voltage + - current + default: voltage + +required: + - compatible + - regulator-name + - gpios + - states + +examples: + - | + gpio-regulator { + compatible = "regulator-gpio"; + + regulator-name = "mmci-gpio-supply"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2600000>; + regulator-boot-on; + + enable-gpios = <&gpio0 23 0x4>; + gpios = <&gpio0 24 0x4 + &gpio0 25 0x4>; + states = <1800000 0x3>, + <2200000 0x2>, + <2600000 0x1>, + <2900000 0x0>; + + startup-delay-us = <100000>; + enable-active-high; + }; +... diff --git a/Documentation/devicetree/bindings/regulator/max8660.txt b/Documentation/devicetree/bindings/regulator/max8660.txt deleted file mode 100644 index 8ba994d8a142..000000000000 --- a/Documentation/devicetree/bindings/regulator/max8660.txt +++ /dev/null @@ -1,47 +0,0 @@ -Maxim MAX8660 voltage regulator - -Required properties: -- compatible: must be one of "maxim,max8660", "maxim,max8661" -- reg: I2C slave address, usually 0x34 -- any required generic properties defined in regulator.txt - -Example: - - i2c_master { - max8660@34 { - compatible = "maxim,max8660"; - reg = <0x34>; - - regulators { - regulator@0 { - regulator-compatible= "V3(DCDC)"; - regulator-min-microvolt = <725000>; - regulator-max-microvolt = <1800000>; - }; - - regulator@1 { - regulator-compatible= "V4(DCDC)"; - regulator-min-microvolt = <725000>; - regulator-max-microvolt = <1800000>; - }; - - regulator@2 { - regulator-compatible= "V5(LDO)"; - regulator-min-microvolt = <1700000>; - regulator-max-microvolt = <2000000>; - }; - - regulator@3 { - regulator-compatible= "V6(LDO)"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - }; - - regulator@4 { - regulator-compatible= "V7(LDO)"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - }; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/regulator/max8660.yaml b/Documentation/devicetree/bindings/regulator/max8660.yaml new file mode 100644 index 000000000000..9c038698f880 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max8660.yaml @@ -0,0 +1,77 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/max8660.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim MAX8660 voltage regulator + +maintainers: + - Daniel Mack <zonque@gmail.com> + +properties: + $nodename: + pattern: "pmic@[0-9a-f]{1,2}" + compatible: + enum: + - maxim,max8660 + - maxim,max8661 + + reg: + maxItems: 1 + + regulators: + type: object + + patternProperties: + "regulator-.+": + $ref: "regulator.yaml#" + + additionalProperties: false + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pmic@34 { + compatible = "maxim,max8660"; + reg = <0x34>; + + regulators { + regulator-V3 { + regulator-compatible= "V3(DCDC)"; + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <1800000>; + }; + + regulator-V4 { + regulator-compatible= "V4(DCDC)"; + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <1800000>; + }; + + regulator-V5 { + regulator-compatible= "V5(LDO)"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <2000000>; + }; + + regulator-V6 { + regulator-compatible= "V6(LDO)"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + regulator-V7 { + regulator-compatible= "V7(LDO)"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/regulator/mt6358-regulator.txt b/Documentation/devicetree/bindings/regulator/mt6358-regulator.txt new file mode 100644 index 000000000000..9a90a92f2d7e --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/mt6358-regulator.txt @@ -0,0 +1,358 @@ +MediaTek MT6358 Regulator + +All voltage regulators provided by the MT6358 PMIC are described as the +subnodes of the MT6358 regulators node. Each regulator is named according +to its regulator type, buck_<name> and ldo_<name>. The definition for each +of these nodes is defined using the standard binding for regulators at +Documentation/devicetree/bindings/regulator/regulator.txt. + +The valid names for regulators are:: +BUCK: + buck_vdram1, buck_vcore, buck_vpa, buck_vproc11, buck_vproc12, buck_vgpu, + buck_vs2, buck_vmodem, buck_vs1 +LDO: + ldo_vdram2, ldo_vsim1, ldo_vibr, ldo_vrf12, ldo_vio18, ldo_vusb, ldo_vcamio, + ldo_vcamd, ldo_vcn18, ldo_vfe28, ldo_vsram_proc11, ldo_vcn28, ldo_vsram_others, + ldo_vsram_gpu, ldo_vxo22, ldo_vefuse, ldo_vaux18, ldo_vmch, ldo_vbif28, + ldo_vsram_proc12, ldo_vcama1, ldo_vemc, ldo_vio28, ldo_va12, ldo_vrf18, + ldo_vcn33_bt, ldo_vcn33_wifi, ldo_vcama2, ldo_vmc, ldo_vldo28, ldo_vaud28, + ldo_vsim2 + +Example: + + pmic { + compatible = "mediatek,mt6358"; + + mt6358regulator: mt6358regulator { + compatible = "mediatek,mt6358-regulator"; + + mt6358_vdram1_reg: buck_vdram1 { + regulator-compatible = "buck_vdram1"; + regulator-name = "vdram1"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <2087500>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <0>; + regulator-always-on; + }; + + mt6358_vcore_reg: buck_vcore { + regulator-name = "vcore"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1293750>; + regulator-ramp-delay = <6250>; + regulator-enable-ramp-delay = <200>; + regulator-always-on; + }; + + mt6358_vpa_reg: buck_vpa { + regulator-name = "vpa"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3650000>; + regulator-ramp-delay = <50000>; + regulator-enable-ramp-delay = <250>; + }; + + mt6358_vproc11_reg: buck_vproc11 { + regulator-name = "vproc11"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1293750>; + regulator-ramp-delay = <6250>; + regulator-enable-ramp-delay = <200>; + regulator-always-on; + }; + + mt6358_vproc12_reg: buck_vproc12 { + regulator-name = "vproc12"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1293750>; + regulator-ramp-delay = <6250>; + regulator-enable-ramp-delay = <200>; + regulator-always-on; + }; + + mt6358_vgpu_reg: buck_vgpu { + regulator-name = "vgpu"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1293750>; + regulator-ramp-delay = <6250>; + regulator-enable-ramp-delay = <200>; + }; + + mt6358_vs2_reg: buck_vs2 { + regulator-name = "vs2"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <2087500>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <0>; + regulator-always-on; + }; + + mt6358_vmodem_reg: buck_vmodem { + regulator-name = "vmodem"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1293750>; + regulator-ramp-delay = <6250>; + regulator-enable-ramp-delay = <900>; + regulator-always-on; + }; + + mt6358_vs1_reg: buck_vs1 { + regulator-name = "vs1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <2587500>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <0>; + regulator-always-on; + }; + + mt6358_vdram2_reg: ldo_vdram2 { + regulator-name = "vdram2"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <3300>; + }; + + mt6358_vsim1_reg: ldo_vsim1 { + regulator-name = "vsim1"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <3100000>; + regulator-enable-ramp-delay = <540>; + }; + + mt6358_vibr_reg: ldo_vibr { + regulator-name = "vibr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <60>; + }; + + mt6358_vrf12_reg: ldo_vrf12 { + compatible = "regulator-fixed"; + regulator-name = "vrf12"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-enable-ramp-delay = <120>; + }; + + mt6358_vio18_reg: ldo_vio18 { + compatible = "regulator-fixed"; + regulator-name = "vio18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <2700>; + regulator-always-on; + }; + + mt6358_vusb_reg: ldo_vusb { + regulator-name = "vusb"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3100000>; + regulator-enable-ramp-delay = <270>; + regulator-always-on; + }; + + mt6358_vcamio_reg: ldo_vcamio { + compatible = "regulator-fixed"; + regulator-name = "vcamio"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <270>; + }; + + mt6358_vcamd_reg: ldo_vcamd { + regulator-name = "vcamd"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <270>; + }; + + mt6358_vcn18_reg: ldo_vcn18 { + compatible = "regulator-fixed"; + regulator-name = "vcn18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <270>; + }; + + mt6358_vfe28_reg: ldo_vfe28 { + compatible = "regulator-fixed"; + regulator-name = "vfe28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <270>; + }; + + mt6358_vsram_proc11_reg: ldo_vsram_proc11 { + regulator-name = "vsram_proc11"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1293750>; + regulator-ramp-delay = <6250>; + regulator-enable-ramp-delay = <240>; + regulator-always-on; + }; + + mt6358_vcn28_reg: ldo_vcn28 { + compatible = "regulator-fixed"; + regulator-name = "vcn28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <270>; + }; + + mt6358_vsram_others_reg: ldo_vsram_others { + regulator-name = "vsram_others"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1293750>; + regulator-ramp-delay = <6250>; + regulator-enable-ramp-delay = <240>; + regulator-always-on; + }; + + mt6358_vsram_gpu_reg: ldo_vsram_gpu { + regulator-name = "vsram_gpu"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1293750>; + regulator-ramp-delay = <6250>; + regulator-enable-ramp-delay = <240>; + }; + + mt6358_vxo22_reg: ldo_vxo22 { + compatible = "regulator-fixed"; + regulator-name = "vxo22"; + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2200000>; + regulator-enable-ramp-delay = <120>; + regulator-always-on; + }; + + mt6358_vefuse_reg: ldo_vefuse { + regulator-name = "vefuse"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <1900000>; + regulator-enable-ramp-delay = <270>; + }; + + mt6358_vaux18_reg: ldo_vaux18 { + compatible = "regulator-fixed"; + regulator-name = "vaux18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <270>; + }; + + mt6358_vmch_reg: ldo_vmch { + regulator-name = "vmch"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <60>; + }; + + mt6358_vbif28_reg: ldo_vbif28 { + compatible = "regulator-fixed"; + regulator-name = "vbif28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <270>; + }; + + mt6358_vsram_proc12_reg: ldo_vsram_proc12 { + regulator-name = "vsram_proc12"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1293750>; + regulator-ramp-delay = <6250>; + regulator-enable-ramp-delay = <240>; + regulator-always-on; + }; + + mt6358_vcama1_reg: ldo_vcama1 { + regulator-name = "vcama1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <270>; + }; + + mt6358_vemc_reg: ldo_vemc { + regulator-name = "vemc"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <60>; + regulator-always-on; + }; + + mt6358_vio28_reg: ldo_vio28 { + compatible = "regulator-fixed"; + regulator-name = "vio28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <270>; + }; + + mt6358_va12_reg: ldo_va12 { + compatible = "regulator-fixed"; + regulator-name = "va12"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-enable-ramp-delay = <270>; + regulator-always-on; + }; + + mt6358_vrf18_reg: ldo_vrf18 { + compatible = "regulator-fixed"; + regulator-name = "vrf18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <120>; + }; + + mt6358_vcn33_bt_reg: ldo_vcn33_bt { + regulator-name = "vcn33_bt"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3500000>; + regulator-enable-ramp-delay = <270>; + }; + + mt6358_vcn33_wifi_reg: ldo_vcn33_wifi { + regulator-name = "vcn33_wifi"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3500000>; + regulator-enable-ramp-delay = <270>; + }; + + mt6358_vcama2_reg: ldo_vcama2 { + regulator-name = "vcama2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <270>; + }; + + mt6358_vmc_reg: ldo_vmc { + regulator-name = "vmc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <60>; + }; + + mt6358_vldo28_reg: ldo_vldo28 { + regulator-name = "vldo28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <270>; + }; + + mt6358_vaud28_reg: ldo_vaud28 { + compatible = "regulator-fixed"; + regulator-name = "vaud28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <270>; + }; + + mt6358_vsim2_reg: ldo_vsim2 { + regulator-name = "vsim2"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <3100000>; + regulator-enable-ramp-delay = <540>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/pv88060.txt b/Documentation/devicetree/bindings/regulator/pv88060.txt index 10a6dadc008e..6a7c8a92fdb0 100644 --- a/Documentation/devicetree/bindings/regulator/pv88060.txt +++ b/Documentation/devicetree/bindings/regulator/pv88060.txt @@ -121,4 +121,4 @@ Example regulator-max-microvolt = <5000000>; }; }; - };
\ No newline at end of file + }; diff --git a/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.txt index 7ef2dbe48e8a..bab9f71140b8 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.txt @@ -22,9 +22,12 @@ RPMh resource. The names used for regulator nodes must match those supported by a given PMIC. Supported regulator node names: + PM8005: smps1 - smps4 + PM8009: smps1 - smps2, ldo1 - ldo7 + PM8150: smps1 - smps10, ldo1 - ldo18 + PM8150L: smps1 - smps8, ldo1 - ldo11, bob, flash, rgb PM8998: smps1 - smps13, ldo1 - ldo28, lvs1 - lvs2 PMI8998: bob - PM8005: smps1 - smps4 ======================== First Level Nodes - PMIC @@ -33,9 +36,13 @@ First Level Nodes - PMIC - compatible Usage: required Value type: <string> - Definition: Must be one of: "qcom,pm8998-rpmh-regulators", - "qcom,pmi8998-rpmh-regulators" or - "qcom,pm8005-rpmh-regulators". + Definition: Must be one of below: + "qcom,pm8005-rpmh-regulators" + "qcom,pm8009-rpmh-regulators" + "qcom,pm8150-rpmh-regulators" + "qcom,pm8150l-rpmh-regulators" + "qcom,pm8998-rpmh-regulators" + "qcom,pmi8998-rpmh-regulators" - qcom,pmic-id Usage: required @@ -97,7 +104,7 @@ Second Level Nodes - Regulators sent for this regulator including those which are for a strictly lower power state. -Other properties defined in Documentation/devicetree/bindings/regulator.txt +Other properties defined in Documentation/devicetree/bindings/regulator/regulator.txt may also be used. regulator-initial-mode and regulator-allowed-modes may be specified for VRM regulators using mode values from include/dt-bindings/regulator/qcom,rpmh-regulator.h. regulator-allow-bypass diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt index 406f2e570c50..430b8622bda1 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt @@ -4,11 +4,13 @@ Qualcomm SPMI Regulators Usage: required Value type: <string> Definition: must be one of: + "qcom,pm8005-regulators" "qcom,pm8841-regulators" "qcom,pm8916-regulators" "qcom,pm8941-regulators" "qcom,pm8994-regulators" "qcom,pmi8994-regulators" + "qcom,pms405-regulators" - interrupts: Usage: optional @@ -110,6 +112,23 @@ Qualcomm SPMI Regulators Definition: Reference to regulator supplying the input pin, as described in the data sheet. +- vdd_l1_l2-supply: +- vdd_l3_l8-supply: +- vdd_l4-supply: +- vdd_l5_l6-supply: +- vdd_l10_l11_l12_l13-supply: +- vdd_l7-supply: +- vdd_l9-supply: +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_s4-supply: +- vdd_s5-supply + Usage: optional (pms405 only) + Value type: <phandle> + Definition: Reference to regulator supplying the input pin, as + described in the data sheet. + - qcom,saw-reg: Usage: optional Value type: <phandle> @@ -120,6 +139,9 @@ The regulator node houses sub-nodes for each regulator within the device. Each sub-node is identified using the node's name, with valid values listed for each of the PMICs below. +pm8005: + s1, s2, s3, s4 + pm8841: s1, s2, s3, s4, s5, s6, s7, s8 diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 0a3f087d5844..487ccd8370b3 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -1,139 +1 @@ -Voltage/Current Regulators - -Optional properties: -- regulator-name: A string used as a descriptive name for regulator outputs -- regulator-min-microvolt: smallest voltage consumers may set -- regulator-max-microvolt: largest voltage consumers may set -- regulator-microvolt-offset: Offset applied to voltages to compensate for voltage drops -- regulator-min-microamp: smallest current consumers may set -- regulator-max-microamp: largest current consumers may set -- regulator-input-current-limit-microamp: maximum input current regulator allows -- regulator-always-on: boolean, regulator should never be disabled -- regulator-boot-on: bootloader/firmware enabled regulator -- regulator-allow-bypass: allow the regulator to go into bypass mode -- regulator-allow-set-load: allow the regulator performance level to be configured -- <name>-supply: phandle to the parent supply/regulator node -- regulator-ramp-delay: ramp delay for regulator(in uV/us) - For hardware which supports disabling ramp rate, it should be explicitly - initialised to zero (regulator-ramp-delay = <0>) for disabling ramp delay. -- regulator-enable-ramp-delay: The time taken, in microseconds, for the supply - rail to reach the target voltage, plus/minus whatever tolerance the board - design requires. This property describes the total system ramp time - required due to the combination of internal ramping of the regulator itself, - and board design issues such as trace capacitance and load on the supply. -- regulator-settling-time-us: Settling time, in microseconds, for voltage - change if regulator have the constant time for any level voltage change. - This is useful when regulator have exponential voltage change. -- regulator-settling-time-up-us: Settling time, in microseconds, for voltage - increase if the regulator needs a constant time to settle after voltage - increases of any level. This is useful for regulators with exponential - voltage changes. -- regulator-settling-time-down-us: Settling time, in microseconds, for voltage - decrease if the regulator needs a constant time to settle after voltage - decreases of any level. This is useful for regulators with exponential - voltage changes. -- regulator-soft-start: Enable soft start so that voltage ramps slowly -- regulator-state-standby sub-root node for Standby mode - : equivalent with standby Linux sleep state, which provides energy savings - with a relatively quick transition back time. -- regulator-state-mem sub-root node for Suspend-to-RAM mode - : suspend to memory, the device goes to sleep, but all data stored in memory, - only some external interrupt can wake the device. -- regulator-state-disk sub-root node for Suspend-to-DISK mode - : suspend to disk, this state operates similarly to Suspend-to-RAM, - but includes a final step of writing memory contents to disk. -- regulator-state-[mem/disk/standby] node has following common properties: - - regulator-on-in-suspend: regulator should be on in suspend state. - - regulator-off-in-suspend: regulator should be off in suspend state. - - regulator-suspend-min-microvolt: minimum voltage may be set in - suspend state. - - regulator-suspend-max-microvolt: maximum voltage may be set in - suspend state. - - regulator-suspend-microvolt: the default voltage which regulator - would be set in suspend. This property is now deprecated, instead - setting voltage for suspend mode via the API which regulator - driver provides is recommended. - - regulator-changeable-in-suspend: whether the default voltage and - the regulator on/off in suspend can be changed in runtime. - - regulator-mode: operating mode in the given suspend state. - The set of possible operating modes depends on the capabilities of - every hardware so the valid modes are documented on each regulator - device tree binding document. -- regulator-initial-mode: initial operating mode. The set of possible operating - modes depends on the capabilities of every hardware so each device binding - documentation explains which values the regulator supports. -- regulator-allowed-modes: list of operating modes that software is allowed to - configure for the regulator at run-time. Elements may be specified in any - order. The set of possible operating modes depends on the capabilities of - every hardware so each device binding document explains which values the - regulator supports. -- regulator-system-load: Load in uA present on regulator that is not captured by - any consumer request. -- regulator-pull-down: Enable pull down resistor when the regulator is disabled. -- regulator-over-current-protection: Enable over current protection. -- regulator-active-discharge: tristate, enable/disable active discharge of - regulators. The values are: - 0: Disable active discharge. - 1: Enable active discharge. - Absence of this property will leave configuration to default. -- regulator-coupled-with: Regulators with which the regulator - is coupled. The linkage is 2-way - all coupled regulators should be linked - with each other. A regulator should not be coupled with its supplier. -- regulator-coupled-max-spread: Array of maximum spread between voltages of - coupled regulators in microvolts, each value in the array relates to the - corresponding couple specified by the regulator-coupled-with property. -- regulator-max-step-microvolt: Maximum difference between current and target - voltages that can be changed safely in a single step. - -Deprecated properties: -- regulator-compatible: If a regulator chip contains multiple - regulators, and if the chip's binding contains a child node that - describes each regulator, then this property indicates which regulator - this child node is intended to configure. If this property is missing, - the node's name will be used instead. - -Example: - - xyzreg: regulator@0 { - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <2500000>; - regulator-always-on; - vin-supply = <&vin>; - - regulator-state-mem { - regulator-on-in-suspend; - }; - }; - -Regulator Consumers: -Consumer nodes can reference one or more of its supplies/ -regulators using the below bindings. - -- <name>-supply: phandle to the regulator node - -These are the same bindings that a regulator in the above -example used to reference its own supply, in which case -its just seen as a special case of a regulator being a -consumer itself. - -Example of a consumer device node (mmc) referencing two -regulators (twl_reg1 and twl_reg2), - - twl_reg1: regulator@0 { - ... - ... - ... - }; - - twl_reg2: regulator@1 { - ... - ... - ... - }; - - mmc: mmc@0 { - ... - ... - vmmc-supply = <&twl_reg1>; - vmmcaux-supply = <&twl_reg2>; - }; +This file has moved to regulator.yaml. diff --git a/Documentation/devicetree/bindings/regulator/regulator.yaml b/Documentation/devicetree/bindings/regulator/regulator.yaml new file mode 100644 index 000000000000..02c3043ce419 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/regulator.yaml @@ -0,0 +1,200 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Voltage/Current Regulators + +maintainers: + - Liam Girdwood <lgirdwood@gmail.com> + - Mark Brown <broonie@kernel.org> + +properties: + regulator-name: + description: A string used as a descriptive name for regulator outputs + $ref: "/schemas/types.yaml#/definitions/string" + + regulator-min-microvolt: + description: smallest voltage consumers may set + + regulator-max-microvolt: + description: largest voltage consumers may set + + regulator-microvolt-offset: + description: Offset applied to voltages to compensate for voltage drops + + regulator-min-microamp: + description: smallest current consumers may set + + regulator-max-microamp: + description: largest current consumers may set + + regulator-input-current-limit-microamp: + description: maximum input current regulator allows + + regulator-always-on: + description: boolean, regulator should never be disabled + type: boolean + + regulator-boot-on: + description: bootloader/firmware enabled regulator + type: boolean + + regulator-allow-bypass: + description: allow the regulator to go into bypass mode + type: boolean + + regulator-allow-set-load: + description: allow the regulator performance level to be configured + type: boolean + + regulator-ramp-delay: + description: ramp delay for regulator(in uV/us) For hardware which supports + disabling ramp rate, it should be explicitly initialised to zero (regulator-ramp-delay + = <0>) for disabling ramp delay. + $ref: "/schemas/types.yaml#/definitions/uint32" + + regulator-enable-ramp-delay: + description: The time taken, in microseconds, for the supply rail to + reach the target voltage, plus/minus whatever tolerance the board + design requires. This property describes the total system ramp time + required due to the combination of internal ramping of the regulator + itself, and board design issues such as trace capacitance and load + on the supply. + $ref: "/schemas/types.yaml#/definitions/uint32" + + regulator-settling-time-us: + description: Settling time, in microseconds, for voltage change if regulator + have the constant time for any level voltage change. This is useful + when regulator have exponential voltage change. + + regulator-settling-time-up-us: + description: Settling time, in microseconds, for voltage increase if + the regulator needs a constant time to settle after voltage increases + of any level. This is useful for regulators with exponential voltage + changes. + + regulator-settling-time-down-us: + description: Settling time, in microseconds, for voltage decrease if + the regulator needs a constant time to settle after voltage decreases + of any level. This is useful for regulators with exponential voltage + changes. + + regulator-soft-start: + description: Enable soft start so that voltage ramps slowly + type: boolean + + regulator-initial-mode: + description: initial operating mode. The set of possible operating modes + depends on the capabilities of every hardware so each device binding + documentation explains which values the regulator supports. + $ref: "/schemas/types.yaml#/definitions/uint32" + + regulator-allowed-modes: + description: list of operating modes that software is allowed to configure + for the regulator at run-time. Elements may be specified in any order. + The set of possible operating modes depends on the capabilities of + every hardware so each device binding document explains which values + the regulator supports. + $ref: "/schemas/types.yaml#/definitions/uint32-array" + + regulator-system-load: + description: Load in uA present on regulator that is not captured by + any consumer request. + $ref: "/schemas/types.yaml#/definitions/uint32" + + regulator-pull-down: + description: Enable pull down resistor when the regulator is disabled. + type: boolean + + regulator-over-current-protection: + description: Enable over current protection. + type: boolean + + regulator-active-discharge: + description: | + tristate, enable/disable active discharge of regulators. The values are: + 0: Disable active discharge. + 1: Enable active discharge. + Absence of this property will leave configuration to default. + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - enum: [ 0, 1 ] + + regulator-coupled-with: + description: Regulators with which the regulator is coupled. The linkage + is 2-way - all coupled regulators should be linked with each other. + A regulator should not be coupled with its supplier. + $ref: "/schemas/types.yaml#/definitions/phandle-array" + + regulator-coupled-max-spread: + description: Array of maximum spread between voltages of coupled regulators + in microvolts, each value in the array relates to the corresponding + couple specified by the regulator-coupled-with property. + $ref: "/schemas/types.yaml#/definitions/uint32" + + regulator-max-step-microvolt: + description: Maximum difference between current and target voltages + that can be changed safely in a single step. + +patternProperties: + ".*-supply$": + description: Input supply phandle(s) for this node + + regulator-state-(standby|mem|disk): + type: object + description: + sub-nodes for regulator state in Standby, Suspend-to-RAM, and + Suspend-to-DISK modes. Equivalent with standby, mem, and disk Linux + sleep states. + + properties: + regulator-on-in-suspend: + description: regulator should be on in suspend state. + type: boolean + + regulator-off-in-suspend: + description: regulator should be off in suspend state. + type: boolean + + regulator-suspend-min-microvolt: + description: minimum voltage may be set in suspend state. + + regulator-suspend-max-microvolt: + description: maximum voltage may be set in suspend state. + + regulator-suspend-microvolt: + description: the default voltage which regulator would be set in + suspend. This property is now deprecated, instead setting voltage + for suspend mode via the API which regulator driver provides is + recommended. + + regulator-changeable-in-suspend: + description: whether the default voltage and the regulator on/off + in suspend can be changed in runtime. + type: boolean + + regulator-mode: + description: operating mode in the given suspend state. The set + of possible operating modes depends on the capabilities of every + hardware so the valid modes are documented on each regulator device + tree binding document. + $ref: "/schemas/types.yaml#/definitions/uint32" + + additionalProperties: false + +examples: + - | + xyzreg: regulator@0 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + vin-supply = <&vin>; + + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/regulator/slg51000.txt b/Documentation/devicetree/bindings/regulator/slg51000.txt new file mode 100644 index 000000000000..aa0733e49b90 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/slg51000.txt @@ -0,0 +1,88 @@ +* Dialog Semiconductor SLG51000 Voltage Regulator + +Required properties: +- compatible : Should be "dlg,slg51000" for SLG51000 +- reg : Specifies the I2C slave address. +- xxx-supply: Input voltage supply regulator for ldo3 to ldo7. + These entries are required if regulators are enabled for a device. + An absence of these properties can cause the regulator registration to fail. + If some of input supply is powered through battery or always-on supply then + also it is required to have these parameters with proper node handle of always + on power supply. + vin3-supply: Input supply for ldo3 + vin4-supply: Input supply for ldo4 + vin5-supply: Input supply for ldo5 + vin6-supply: Input supply for ldo6 + vin7-supply: Input supply for ldo7 + +Optional properties: +- interrupt-parent : Specifies the reference to the interrupt controller. +- interrupts : IRQ line information. +- dlg,cs-gpios : Specify a valid GPIO for chip select + +Sub-nodes: +- regulators : This node defines the settings for the regulators. + The content of the sub-node is defined by the standard binding + for regulators; see regulator.txt. + + The SLG51000 regulators are bound using their names listed below: + ldo1 + ldo2 + ldo3 + ldo4 + ldo5 + ldo6 + ldo7 + +Optional properties for regulators: +- enable-gpios : Specify a valid GPIO for platform control of the regulator. + +Example: + pmic: slg51000@75 { + compatible = "dlg,slg51000"; + reg = <0x75>; + + regulators { + ldo1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <2400000>; + regulator-max-microvolt = <3300000>; + }; + + ldo2 { + regulator-name = "ldo2"; + regulator-min-microvolt = <2400000>; + regulator-max-microvolt = <3300000>; + }; + + ldo3 { + regulator-name = "ldo3"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3750000>; + }; + + ldo4 { + regulator-name = "ldo4"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3750000>; + }; + + ldo5 { + regulator-name = "ldo5"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1200000>; + }; + + ldo6 { + regulator-name = "ldo6"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1200000>; + }; + + ldo7 { + regulator-name = "ldo7"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3750000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/st,stm32-booster.txt b/Documentation/devicetree/bindings/regulator/st,stm32-booster.txt new file mode 100644 index 000000000000..479ad4c8758e --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/st,stm32-booster.txt @@ -0,0 +1,18 @@ +STM32 BOOSTER - Booster for ADC analog input switches + +Some STM32 devices embed a 3.3V booster supplied by Vdda, that can be used +to supply ADC analog input switches. + +Required properties: +- compatible: Should be one of: + "st,stm32h7-booster" + "st,stm32mp1-booster" +- st,syscfg: Phandle to system configuration controller. +- vdda-supply: Phandle to the vdda input analog voltage. + +Example: + booster: regulator-booster { + compatible = "st,stm32mp1-booster"; + st,syscfg = <&syscfg>; + vdda-supply = <&vdda>; + }; diff --git a/Documentation/devicetree/bindings/regulator/sy8824x.txt b/Documentation/devicetree/bindings/regulator/sy8824x.txt new file mode 100644 index 000000000000..c5e95850c427 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/sy8824x.txt @@ -0,0 +1,24 @@ +SY8824C/SY8824E/SY20276 Voltage regulator + +Required properties: +- compatible: Must be one of the following. + "silergy,sy8824c" + "silergy,sy8824e" + "silergy,sy20276" + "silergy,sy20278" +- reg: I2C slave address + +Any property defined as part of the core regulator binding, defined in +./regulator.txt, can also be used. + +Example: + + vcore: regulator@00 { + compatible = "silergy,sy8824c"; + reg = <0x66>; + regulator-name = "vcore"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; diff --git a/Documentation/devicetree/bindings/regulator/twl-regulator.txt b/Documentation/devicetree/bindings/regulator/twl-regulator.txt index 74a91c4f8530..549f80436deb 100644 --- a/Documentation/devicetree/bindings/regulator/twl-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/twl-regulator.txt @@ -71,3 +71,10 @@ Example: regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3000000>; }; + +For twl6030 regulators/LDOs: + + - ti,retain-on-reset: Does not turn off the supplies during warm + reset. Could be needed for VMMC, as TWL6030 + reset sequence for this signal does not comply + with the SD specification. diff --git a/Documentation/devicetree/bindings/regulator/uniphier-regulator.txt b/Documentation/devicetree/bindings/regulator/uniphier-regulator.txt index c9919f4b92d2..94fd38b0d163 100644 --- a/Documentation/devicetree/bindings/regulator/uniphier-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/uniphier-regulator.txt @@ -13,6 +13,7 @@ this layer. These clocks and resets should be described in each property. Required properties: - compatible: Should be "socionext,uniphier-pro4-usb3-regulator" - for Pro4 SoC + "socionext,uniphier-pro5-usb3-regulator" - for Pro5 SoC "socionext,uniphier-pxs2-usb3-regulator" - for PXs2 SoC "socionext,uniphier-ld20-usb3-regulator" - for LD20 SoC "socionext,uniphier-pxs3-usb3-regulator" - for PXs3 SoC @@ -20,12 +21,12 @@ Required properties: - clocks: A list of phandles to the clock gate for USB3 glue layer. According to the clock-names, appropriate clocks are required. - clock-names: Should contain - "gio", "link" - for Pro4 SoC + "gio", "link" - for Pro4 and Pro5 SoCs "link" - for others - resets: A list of phandles to the reset control for USB3 glue layer. According to the reset-names, appropriate resets are required. - reset-names: Should contain - "gio", "link" - for Pro4 SoC + "gio", "link" - for Pro4 and Pro5 SoCs "link" - for others See Documentation/devicetree/bindings/regulator/regulator.txt diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,adsp-pil.txt b/Documentation/devicetree/bindings/remoteproc/qcom,hexagon-v56.txt index 66af2c30944f..1337a3d93d35 100644 --- a/Documentation/devicetree/bindings/remoteproc/qcom,adsp-pil.txt +++ b/Documentation/devicetree/bindings/remoteproc/qcom,hexagon-v56.txt @@ -1,12 +1,13 @@ -Qualcomm Technology Inc. ADSP Peripheral Image Loader +Qualcomm Technology Inc. Hexagon v56 Peripheral Image Loader This document defines the binding for a component that loads and boots firmware -on the Qualcomm Technology Inc. ADSP Hexagon core. +on the Qualcomm Technology Inc. Hexagon v56 core. - compatible: Usage: required Value type: <string> Definition: must be one of: + "qcom,qcs404-cdsp-pil", "qcom,sdm845-adsp-pil" - reg: @@ -28,10 +29,11 @@ on the Qualcomm Technology Inc. ADSP Hexagon core. - clocks: Usage: required Value type: <prop-encoded-array> - Definition: List of 8 phandle and clock specifier pairs for the adsp. + Definition: List of phandles and clock specifier pairs for the Hexagon, + per clock-names below. - clock-names: - Usage: required + Usage: required for SDM845 ADSP Value type: <stringlist> Definition: List of clock input name strings sorted in the same order as the clocks property. Definition must have @@ -39,6 +41,14 @@ on the Qualcomm Technology Inc. ADSP Hexagon core. "lpass_ahbm_aon_cbcr", "qdsp6ss_xo", "qdsp6ss_sleep" and "qdsp6ss_core". +- clock-names: + Usage: required for QCS404 CDSP + Value type: <stringlist> + Definition: List of clock input name strings sorted in the same + order as the clocks property. Definition must have + "xo", "sway", "tbu", "bimc", "ahb_aon", "q6ss_slave", + "q6ss_master", "q6_axim". + - power-domains: Usage: required Value type: <phandle> @@ -47,28 +57,33 @@ on the Qualcomm Technology Inc. ADSP Hexagon core. - resets: Usage: required Value type: <phandle> - Definition: reference to the list of 2 reset-controller for the adsp. + Definition: reference to the list of resets for the Hexagon. - reset-names: - Usage: required + Usage: required for SDM845 ADSP Value type: <stringlist> Definition: must be "pdc_sync" and "cc_lpass" +- reset-names: + Usage: required for QCS404 CDSP + Value type: <stringlist> + Definition: must be "restart" + - qcom,halt-regs: Usage: required Value type: <prop-encoded-array> Definition: a phandle reference to a syscon representing TCSR followed - by the offset within syscon for lpass halt register. + by the offset within syscon for Hexagon halt register. - memory-region: Usage: required Value type: <phandle> - Definition: reference to the reserved-memory for the ADSP + Definition: reference to the reserved-memory for the firmware - qcom,smem-states: Usage: required Value type: <phandle> - Definition: reference to the smem state for requesting the ADSP to + Definition: reference to the smem state for requesting the Hexagon to shut down - qcom,smem-state-names: @@ -79,7 +94,7 @@ on the Qualcomm Technology Inc. ADSP Hexagon core. = SUBNODES The adsp node may have an subnode named "glink-edge" that describes the -communication edge, channels and devices related to the ADSP. +communication edge, channels and devices related to the Hexagon. See ../soc/qcom/qcom,glink.txt for details on how to describe these. = EXAMPLE diff --git a/Documentation/devicetree/bindings/remoteproc/stm32-rproc.txt b/Documentation/devicetree/bindings/remoteproc/stm32-rproc.txt new file mode 100644 index 000000000000..5fa915a4b736 --- /dev/null +++ b/Documentation/devicetree/bindings/remoteproc/stm32-rproc.txt @@ -0,0 +1,63 @@ +STMicroelectronics STM32 Remoteproc +----------------------------------- +This document defines the binding for the remoteproc component that loads and +boots firmwares on the ST32MP family chipset. + +Required properties: +- compatible: Must be "st,stm32mp1-m4" +- reg: Address ranges of the RETRAM and MCU SRAM memories used by the + remote processor. +- resets: Reference to a reset controller asserting the remote processor. +- st,syscfg-holdboot: Reference to the system configuration which holds the + remote processor reset hold boot + 1st cell: phandle of syscon block + 2nd cell: register offset containing the hold boot setting + 3rd cell: register bitmask for the hold boot field +- st,syscfg-tz: Reference to the system configuration which holds the RCC trust + zone mode + 1st cell: phandle to syscon block + 2nd cell: register offset containing the RCC trust zone mode setting + 3rd cell: register bitmask for the RCC trust zone mode bit + +Optional properties: +- interrupts: Should contain the watchdog interrupt +- mboxes: This property is required only if the rpmsg/virtio functionality + is used. List of phandle and mailbox channel specifiers: + - a channel (a) used to communicate through virtqueues with the + remote proc. + Bi-directional channel: + - from local to remote = send message + - from remote to local = send message ack + - a channel (b) working the opposite direction of channel (a) + - a channel (c) used by the local proc to notify the remote proc + that it is about to be shut down. + Unidirectional channel: + - from local to remote, where ACK from the remote means + that it is ready for shutdown +- mbox-names: This property is required if the mboxes property is used. + - must be "vq0" for channel (a) + - must be "vq1" for channel (b) + - must be "shutdown" for channel (c) +- memory-region: List of phandles to the reserved memory regions associated with + the remoteproc device. This is variable and describes the + memories shared with the remote processor (eg: remoteproc + firmware and carveouts, rpmsg vrings, ...). + (see ../reserved-memory/reserved-memory.txt) +- st,syscfg-pdds: Reference to the system configuration which holds the remote + processor deep sleep setting + 1st cell: phandle to syscon block + 2nd cell: register offset containing the deep sleep setting + 3rd cell: register bitmask for the deep sleep bit +- st,auto-boot: If defined, when remoteproc is probed, it loads the default + firmware and starts the remote processor. + +Example: + m4_rproc: m4@10000000 { + compatible = "st,stm32mp1-m4"; + reg = <0x10000000 0x40000>, + <0x30000000 0x40000>, + <0x38000000 0x10000>; + resets = <&rcc MCU_R>; + st,syscfg-holdboot = <&rcc 0x10C 0x1>; + st,syscfg-tz = <&rcc 0x000 0x1>; + }; diff --git a/Documentation/devicetree/bindings/reset/amlogic,meson-reset.txt b/Documentation/devicetree/bindings/reset/amlogic,meson-reset.txt deleted file mode 100644 index 28ef6c295c76..000000000000 --- a/Documentation/devicetree/bindings/reset/amlogic,meson-reset.txt +++ /dev/null @@ -1,19 +0,0 @@ -Amlogic Meson SoC Reset Controller -======================================= - -Please also refer to reset.txt in this directory for common reset -controller binding usage. - -Required properties: -- compatible: Should be "amlogic,meson8b-reset", "amlogic,meson-gxbb-reset" or - "amlogic,meson-axg-reset". -- reg: should contain the register address base -- #reset-cells: 1, see below - -example: - -reset: reset-controller { - compatible = "amlogic,meson-gxbb-reset"; - reg = <0x0 0x04404 0x0 0x20>; - #reset-cells = <1>; -}; diff --git a/Documentation/devicetree/bindings/reset/amlogic,meson-reset.yaml b/Documentation/devicetree/bindings/reset/amlogic,meson-reset.yaml new file mode 100644 index 000000000000..00917d868d58 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/amlogic,meson-reset.yaml @@ -0,0 +1,37 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 BayLibre, SAS +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/reset/amlogic,meson-reset.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Amlogic Meson SoC Reset Controller + +maintainers: + - Neil Armstrong <narmstrong@baylibre.com> + +properties: + compatible: + enum: + - amlogic,meson8b-reset # Reset Controller on Meson8b and compatible SoCs + - amlogic,meson-gxbb-reset # Reset Controller on GXBB and compatible SoCs + - amlogic,meson-axg-reset # Reset Controller on AXG and compatible SoCs + + reg: + maxItems: 1 + + "#reset-cells": + const: 1 + +required: + - compatible + - reg + - "#reset-cells" + +examples: + - | + reset-controller@c884404 { + compatible = "amlogic,meson-gxbb-reset"; + reg = <0xc884404 0x20>; + #reset-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/reset/bitmain,bm1880-reset.txt b/Documentation/devicetree/bindings/reset/bitmain,bm1880-reset.txt new file mode 100644 index 000000000000..a6f8455ae6c4 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/bitmain,bm1880-reset.txt @@ -0,0 +1,18 @@ +Bitmain BM1880 SoC Reset Controller +=================================== + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: +- compatible: Should be "bitmain,bm1880-reset" +- reg: Offset and length of reset controller space in SCTRL. +- #reset-cells: Must be 1. + +Example: + + rst: reset-controller@c00 { + compatible = "bitmain,bm1880-reset"; + reg = <0xc00 0x8>; + #reset-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt index 2ecf33815d18..c2489e41a801 100644 --- a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt +++ b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt @@ -8,6 +8,7 @@ Required properties: - compatible: - For i.MX7 SoCs should be "fsl,imx7d-src", "syscon" - For i.MX8MQ SoCs should be "fsl,imx8mq-src", "syscon" + - For i.MX8MM SoCs should be "fsl,imx8mm-src", "fsl,imx8mq-src", "syscon" - reg: should be register base and length as documented in the datasheet - interrupts: Should contain SRC interrupt @@ -45,6 +46,7 @@ Example: }; -For list of all valid reset indicies see -<dt-bindings/reset/imx7-reset.h> for i.MX7 and -<dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ +For list of all valid reset indices see +<dt-bindings/reset/imx7-reset.h> for i.MX7, +<dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ and +<dt-bindings/reset/imx8mq-reset.h> for i.MX8MM diff --git a/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt b/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt index c25da39df707..ea0a6a9734c1 100644 --- a/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt +++ b/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt @@ -11,6 +11,7 @@ Required properties: - compatible: should be one of the following: - "hisilicon,hi6220-sysctrl", "syscon" : For peripheral reset controller. - "hisilicon,hi6220-mediactrl", "syscon" : For media reset controller. + - "hisilicon,hi6220-aoctrl", "syscon" : For ao reset controller. - reg: should be register base and length as documented in the datasheet - #reset-cells: 1, see below diff --git a/Documentation/devicetree/bindings/reset/snps,dw-reset.txt b/Documentation/devicetree/bindings/reset/snps,dw-reset.txt new file mode 100644 index 000000000000..f94f911dd98d --- /dev/null +++ b/Documentation/devicetree/bindings/reset/snps,dw-reset.txt @@ -0,0 +1,30 @@ +Synopsys DesignWare Reset controller +======================================= + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: + +- compatible: should be one of the following. + "snps,dw-high-reset" - for active high configuration + "snps,dw-low-reset" - for active low configuration + +- reg: physical base address of the controller and length of memory mapped + region. + +- #reset-cells: must be 1. + +example: + + dw_rst_1: reset-controller@0000 { + compatible = "snps,dw-high-reset"; + reg = <0x0000 0x4>; + #reset-cells = <1>; + }; + + dw_rst_2: reset-controller@1000 {i + compatible = "snps,dw-low-reset"; + reg = <0x1000 0x8>; + #reset-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/riscv/cpus.txt b/Documentation/devicetree/bindings/riscv/cpus.txt deleted file mode 100644 index adf7b7af5dc3..000000000000 --- a/Documentation/devicetree/bindings/riscv/cpus.txt +++ /dev/null @@ -1,162 +0,0 @@ -=================== -RISC-V CPU Bindings -=================== - -The device tree allows to describe the layout of CPUs in a system through -the "cpus" node, which in turn contains a number of subnodes (ie "cpu") -defining properties for every cpu. - -Bindings for CPU nodes follow the Devicetree Specification, available from: - -https://www.devicetree.org/specifications/ - -with updates for 32-bit and 64-bit RISC-V systems provided in this document. - -=========== -Terminology -=========== - -This document uses some terminology common to the RISC-V community that is not -widely used, the definitions of which are listed here: - -* hart: A hardware execution context, which contains all the state mandated by - the RISC-V ISA: a PC and some registers. This terminology is designed to - disambiguate software's view of execution contexts from any particular - microarchitectural implementation strategy. For example, my Intel laptop is - described as having one socket with two cores, each of which has two hyper - threads. Therefore this system has four harts. - -===================================== -cpus and cpu node bindings definition -===================================== - -The RISC-V architecture, in accordance with the Devicetree Specification, -requires the cpus and cpu nodes to be present and contain the properties -described below. - -- cpus node - - Description: Container of cpu nodes - - The node name must be "cpus". - - A cpus node must define the following properties: - - - #address-cells - Usage: required - Value type: <u32> - Definition: must be set to 1 - - #size-cells - Usage: required - Value type: <u32> - Definition: must be set to 0 - -- cpu node - - Description: Describes a hart context - - PROPERTIES - - - device_type - Usage: required - Value type: <string> - Definition: must be "cpu" - - reg - Usage: required - Value type: <u32> - Definition: The hart ID of this CPU node - - compatible: - Usage: required - Value type: <stringlist> - Definition: must contain "riscv", may contain one of - "sifive,rocket0" - - mmu-type: - Usage: optional - Value type: <string> - Definition: Specifies the CPU's MMU type. Possible values are - "riscv,sv32" - "riscv,sv39" - "riscv,sv48" - - riscv,isa: - Usage: required - Value type: <string> - Definition: Contains the RISC-V ISA string of this hart. These - ISA strings are defined by the RISC-V ISA manual. - -Example: SiFive Freedom U540G Development Kit ---------------------------------------------- - -This system contains two harts: a hart marked as disabled that's used for -low-level system tasks and should be ignored by Linux, and a second hart that -Linux is allowed to run on. - - cpus { - #address-cells = <1>; - #size-cells = <0>; - timebase-frequency = <1000000>; - cpu@0 { - clock-frequency = <1600000000>; - compatible = "sifive,rocket0", "riscv"; - device_type = "cpu"; - i-cache-block-size = <64>; - i-cache-sets = <128>; - i-cache-size = <16384>; - next-level-cache = <&L15 &L0>; - reg = <0>; - riscv,isa = "rv64imac"; - status = "disabled"; - L10: interrupt-controller { - #interrupt-cells = <1>; - compatible = "riscv,cpu-intc"; - interrupt-controller; - }; - }; - cpu@1 { - clock-frequency = <1600000000>; - compatible = "sifive,rocket0", "riscv"; - d-cache-block-size = <64>; - d-cache-sets = <64>; - d-cache-size = <32768>; - d-tlb-sets = <1>; - d-tlb-size = <32>; - device_type = "cpu"; - i-cache-block-size = <64>; - i-cache-sets = <64>; - i-cache-size = <32768>; - i-tlb-sets = <1>; - i-tlb-size = <32>; - mmu-type = "riscv,sv39"; - next-level-cache = <&L15 &L0>; - reg = <1>; - riscv,isa = "rv64imafdc"; - status = "okay"; - tlb-split; - L13: interrupt-controller { - #interrupt-cells = <1>; - compatible = "riscv,cpu-intc"; - interrupt-controller; - }; - }; - }; - -Example: Spike ISA Simulator with 1 Hart ----------------------------------------- - -This device tree matches the Spike ISA golden model as run with `spike -p1`. - - cpus { - cpu@0 { - device_type = "cpu"; - reg = <0x00000000>; - status = "okay"; - compatible = "riscv"; - riscv,isa = "rv64imafdc"; - mmu-type = "riscv,sv48"; - clock-frequency = <0x3b9aca00>; - interrupt-controller { - #interrupt-cells = <0x00000001>; - interrupt-controller; - compatible = "riscv,cpu-intc"; - } - } - } diff --git a/Documentation/devicetree/bindings/riscv/cpus.yaml b/Documentation/devicetree/bindings/riscv/cpus.yaml index f97a4ecd7b91..b261a3015f84 100644 --- a/Documentation/devicetree/bindings/riscv/cpus.yaml +++ b/Documentation/devicetree/bindings/riscv/cpus.yaml @@ -10,97 +10,92 @@ maintainers: - Paul Walmsley <paul.walmsley@sifive.com> - Palmer Dabbelt <palmer@sifive.com> -allOf: - - $ref: /schemas/cpus.yaml# +description: | + This document uses some terminology common to the RISC-V community + that is not widely used, the definitions of which are listed here: + + hart: A hardware execution context, which contains all the state + mandated by the RISC-V ISA: a PC and some registers. This + terminology is designed to disambiguate software's view of execution + contexts from any particular microarchitectural implementation + strategy. For example, an Intel laptop containing one socket with + two cores, each of which has two hyperthreads, could be described as + having four harts. properties: - $nodename: - const: cpus - description: Container of cpu nodes - - '#address-cells': - const: 1 - description: | - A single unsigned 32-bit integer uniquely identifies each RISC-V - hart in a system. (See the "reg" node under the "cpu" node, - below). - - '#size-cells': - const: 0 - -patternProperties: - '^cpu@[0-9a-f]+$': + compatible: + items: + - enum: + - sifive,rocket0 + - sifive,e5 + - sifive,e51 + - sifive,u54-mc + - sifive,u54 + - sifive,u5 + - const: riscv + description: + Identifies that the hart uses the RISC-V instruction set + and identifies the type of the hart. + + mmu-type: + allOf: + - $ref: "/schemas/types.yaml#/definitions/string" + - enum: + - riscv,sv32 + - riscv,sv39 + - riscv,sv48 + description: + Identifies the MMU address translation mode used on this + hart. These values originate from the RISC-V Privileged + Specification document, available from + https://riscv.org/specifications/ + + riscv,isa: + allOf: + - $ref: "/schemas/types.yaml#/definitions/string" + - enum: + - rv64imac + - rv64imafdc + description: + Identifies the specific RISC-V instruction set architecture + supported by the hart. These are documented in the RISC-V + User-Level ISA document, available from + https://riscv.org/specifications/ + + While the isa strings in ISA specification are case + insensitive, letters in the riscv,isa string must be all + lowercase to simplify parsing. + + timebase-frequency: + type: integer + minimum: 1 + description: + Specifies the clock frequency of the system timer in Hz. + This value is common to all harts on a single system image. + + interrupt-controller: + type: object + description: Describes the CPU's local interrupt controller + properties: + '#interrupt-cells': + const: 1 + compatible: - type: array - items: - - enum: - - sifive,rocket0 - - sifive,e5 - - sifive,e51 - - sifive,u54-mc - - sifive,u54 - - sifive,u5 - - const: riscv - description: - Identifies that the hart uses the RISC-V instruction set - and identifies the type of the hart. - - mmu-type: - allOf: - - $ref: "/schemas/types.yaml#/definitions/string" - - enum: - - riscv,sv32 - - riscv,sv39 - - riscv,sv48 - description: - Identifies the MMU address translation mode used on this - hart. These values originate from the RISC-V Privileged - Specification document, available from - https://riscv.org/specifications/ - - riscv,isa: - allOf: - - $ref: "/schemas/types.yaml#/definitions/string" - - enum: - - rv64imac - - rv64imafdc - description: - Identifies the specific RISC-V instruction set architecture - supported by the hart. These are documented in the RISC-V - User-Level ISA document, available from - https://riscv.org/specifications/ - - timebase-frequency: - type: integer - minimum: 1 - description: - Specifies the clock frequency of the system timer in Hz. - This value is common to all harts on a single system image. - - interrupt-controller: - type: object - description: Describes the CPU's local interrupt controller - - properties: - '#interrupt-cells': - const: 1 - - compatible: - const: riscv,cpu-intc - - interrupt-controller: true - - required: - - '#interrupt-cells' - - compatible - - interrupt-controller + const: riscv,cpu-intc + + interrupt-controller: true required: - - riscv,isa - - timebase-frequency + - '#interrupt-cells' + - compatible - interrupt-controller +required: + - riscv,isa + - timebase-frequency + - interrupt-controller + examples: - | // Example 1: SiFive Freedom U540G Development Kit diff --git a/Documentation/devicetree/bindings/riscv/sifive.yaml b/Documentation/devicetree/bindings/riscv/sifive.yaml index 9d17dc2f3f84..3ab532713dc1 100644 --- a/Documentation/devicetree/bindings/riscv/sifive.yaml +++ b/Documentation/devicetree/bindings/riscv/sifive.yaml @@ -19,7 +19,7 @@ properties: compatible: items: - enum: - - sifive,freedom-unleashed-a00 + - sifive,hifive-unleashed-a00 - const: sifive,fu540-c000 - const: sifive,fu540 ... diff --git a/Documentation/devicetree/bindings/rng/amlogic,meson-rng.txt b/Documentation/devicetree/bindings/rng/amlogic,meson-rng.txt deleted file mode 100644 index 4d403645ac9b..000000000000 --- a/Documentation/devicetree/bindings/rng/amlogic,meson-rng.txt +++ /dev/null @@ -1,21 +0,0 @@ -Amlogic Meson Random number generator -===================================== - -Required properties: - -- compatible : should be "amlogic,meson-rng" -- reg : Specifies base physical address and size of the registers. - -Optional properties: - -- clocks : phandle to the following named clocks -- clock-names: Name of core clock, must be "core" - -Example: - -rng { - compatible = "amlogic,meson-rng"; - reg = <0x0 0xc8834000 0x0 0x4>; - clocks = <&clkc CLKID_RNG0>; - clock-names = "core"; -}; diff --git a/Documentation/devicetree/bindings/rng/amlogic,meson-rng.yaml b/Documentation/devicetree/bindings/rng/amlogic,meson-rng.yaml new file mode 100644 index 000000000000..a9ff3cb35c5e --- /dev/null +++ b/Documentation/devicetree/bindings/rng/amlogic,meson-rng.yaml @@ -0,0 +1,37 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 BayLibre, SAS +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/rng/amlogic,meson-rng.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Amlogic Meson Random number generator + +maintainers: + - Neil Armstrong <narmstrong@baylibre.com> + +properties: + compatible: + enum: + - amlogic,meson-rng + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: core + +required: + - compatible + - reg + +examples: + - | + rng@c8834000 { + compatible = "amlogic,meson-rng"; + reg = <0xc8834000 0x4>; + }; diff --git a/Documentation/devicetree/bindings/rng/brcm,iproc-rng200.txt b/Documentation/devicetree/bindings/rng/brcm,iproc-rng200.txt index 0014da9145af..c223e54452da 100644 --- a/Documentation/devicetree/bindings/rng/brcm,iproc-rng200.txt +++ b/Documentation/devicetree/bindings/rng/brcm,iproc-rng200.txt @@ -2,6 +2,7 @@ HWRNG support for the iproc-rng200 driver Required properties: - compatible : Must be one of: + "brcm,bcm7211-rng200" "brcm,bcm7278-rng200" "brcm,iproc-rng200" - reg : base address and size of control register block diff --git a/Documentation/devicetree/bindings/rng/mtk-rng.txt b/Documentation/devicetree/bindings/rng/mtk-rng.txt index 2bc89f133701..dfdcb5cd2ea8 100644 --- a/Documentation/devicetree/bindings/rng/mtk-rng.txt +++ b/Documentation/devicetree/bindings/rng/mtk-rng.txt @@ -6,6 +6,7 @@ Required properties: "mediatek,mt7622-rng", "mediatek,mt7623-rng" : for MT7622 "mediatek,mt7629-rng", "mediatek,mt7623-rng" : for MT7629 "mediatek,mt7623-rng" : for MT7623 + "mediatek,mt8516-rng", "mediatek,mt7623-rng" : for MT8516 - clocks : list of clock specifiers, corresponding to entries in clock-names property; - clock-names : Should contain "rng" entries; diff --git a/Documentation/devicetree/bindings/rng/timeriomem_rng.txt b/Documentation/devicetree/bindings/rng/timeriomem_rng.txt index 214940093b55..fb4846160047 100644 --- a/Documentation/devicetree/bindings/rng/timeriomem_rng.txt +++ b/Documentation/devicetree/bindings/rng/timeriomem_rng.txt @@ -12,7 +12,7 @@ Optional properties: which disables using this rng to automatically fill the kernel's entropy pool. -N.B. currently 'reg' must be four bytes wide and aligned +N.B. currently 'reg' must be at least four bytes wide and 32-bit aligned Example: diff --git a/Documentation/devicetree/bindings/rtc/allwinner,sun4i-a10-rtc.yaml b/Documentation/devicetree/bindings/rtc/allwinner,sun4i-a10-rtc.yaml new file mode 100644 index 000000000000..46d69c32b89b --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/allwinner,sun4i-a10-rtc.yaml @@ -0,0 +1,43 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/rtc/allwinner,sun4i-a10-rtc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 RTC Device Tree Bindings + +allOf: + - $ref: "rtc.yaml#" + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + compatible: + enum: + - allwinner,sun4i-a10-rtc + - allwinner,sun7i-a20-rtc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + rtc: rtc@1c20d00 { + compatible = "allwinner,sun4i-a10-rtc"; + reg = <0x01c20d00 0x20>; + interrupts = <24>; + }; + +... diff --git a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml new file mode 100644 index 000000000000..d7a57ec4a640 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml @@ -0,0 +1,147 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/rtc/allwinner,sun6i-a31-rtc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A31 RTC Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + "#clock-cells": + const: 1 + + compatible: + oneOf: + - const: allwinner,sun6i-a31-rtc + - const: allwinner,sun8i-a23-rtc + - const: allwinner,sun8i-h3-rtc + - const: allwinner,sun8i-r40-rtc + - const: allwinner,sun8i-v3-rtc + - const: allwinner,sun50i-h5-rtc + - items: + - const: allwinner,sun50i-a64-rtc + - const: allwinner,sun8i-h3-rtc + - const: allwinner,sun50i-h6-rtc + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + maxItems: 2 + items: + - description: RTC Alarm 0 + - description: RTC Alarm 1 + + clocks: + maxItems: 1 + + clock-output-names: + minItems: 1 + maxItems: 3 + description: + The RTC provides up to three clocks + - the Low Frequency Oscillator or LOSC, at index 0, + - the Low Frequency Oscillator External output (X32KFOUT in + the datasheet), at index 1, + - the Internal Oscillator, at index 2. + +allOf: + - $ref: "rtc.yaml#" + - if: + properties: + compatible: + contains: + const: allwinner,sun6i-a31-rtc + + then: + properties: + clock-output-names: + minItems: 1 + maxItems: 1 + + - if: + properties: + compatible: + contains: + enum: + - allwinner,sun8i-a23-rtc + - allwinner,sun8i-r40-rtc + - allwinner,sun8i-v3-rtc + + then: + properties: + clock-output-names: + minItems: 2 + maxItems: 2 + + - if: + properties: + compatible: + contains: + enum: + - allwinner,sun8i-h3-rtc + - allwinner,sun50i-h5-rtc + + then: + properties: + clock-output-names: + minItems: 3 + maxItems: 3 + + - if: + properties: + compatible: + contains: + const: allwinner,sun50i-h6-rtc + + then: + properties: + clock-output-names: + minItems: 3 + maxItems: 3 + + - if: + properties: + compatible: + contains: + const: allwinner,sun8i-r40-rtc + + then: + properties: + interrupts: + minItems: 1 + maxItems: 1 + + else: + properties: + interrupts: + minItems: 2 + maxItems: 2 + +required: + - "#clock-cells" + - compatible + - reg + - interrupts + - clocks + - clock-output-names + +additionalProperties: false + +examples: + - | + rtc: rtc@1f00000 { + compatible = "allwinner,sun6i-a31-rtc"; + reg = <0x01f00000 0x400>; + interrupts = <0 40 4>, <0 41 4>; + clock-output-names = "osc32k"; + clocks = <&ext_osc32k>; + #clock-cells = <1>; + }; + +... diff --git a/Documentation/devicetree/bindings/rtc/nxp,rtc-2123.txt b/Documentation/devicetree/bindings/rtc/nxp,rtc-2123.txt index 1994f601800a..7371f525a687 100644 --- a/Documentation/devicetree/bindings/rtc/nxp,rtc-2123.txt +++ b/Documentation/devicetree/bindings/rtc/nxp,rtc-2123.txt @@ -1,7 +1,7 @@ NXP PCF2123 SPI Real Time Clock Required properties: -- compatible: should be: "nxp,rtc-pcf2123" +- compatible: should be: "nxp,pcf2123" or "microcrystal,rv2123" - reg: should be the SPI slave chipselect address @@ -11,7 +11,7 @@ Optional properties: Example: pcf2123: rtc@3 { - compatible = "nxp,rtc-pcf2123" + compatible = "nxp,pcf2123" reg = <3> spi-cs-high; }; diff --git a/Documentation/devicetree/bindings/rtc/pcf8563.txt b/Documentation/devicetree/bindings/rtc/pcf8563.txt index 36984acbb383..6076fe76dbfa 100644 --- a/Documentation/devicetree/bindings/rtc/pcf8563.txt +++ b/Documentation/devicetree/bindings/rtc/pcf8563.txt @@ -3,7 +3,9 @@ Philips PCF8563/Epson RTC8564 Real Time Clock Required properties: -- compatible: Should contain "nxp,pcf8563". +- compatible: Should contain "nxp,pcf8563", + "epson,rtc8564" or + "microcrystal,rv8564" - reg: I2C address for chip. Optional property: diff --git a/Documentation/devicetree/bindings/rtc/rtc-ds1307.txt b/Documentation/devicetree/bindings/rtc/rtc-ds1307.txt index eaee19b60960..66f0a31ae9ce 100644 --- a/Documentation/devicetree/bindings/rtc/rtc-ds1307.txt +++ b/Documentation/devicetree/bindings/rtc/rtc-ds1307.txt @@ -19,6 +19,7 @@ Required properties: "pericom,pt7c4338", "epson,rx8025", "isil,isl12057" + "epson,rx8130" - reg: I2C bus address of the device Optional properties: diff --git a/Documentation/devicetree/bindings/rtc/rtc-fsl-ftm-alarm.txt b/Documentation/devicetree/bindings/rtc/rtc-fsl-ftm-alarm.txt new file mode 100644 index 000000000000..fffac74999da --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/rtc-fsl-ftm-alarm.txt @@ -0,0 +1,36 @@ +Freescale FlexTimer Module (FTM) Alarm + +Required properties: +- compatible : Should be "fsl,<chip>-ftm-alarm", the + supported chips include + "fsl,ls1012a-ftm-alarm" + "fsl,ls1021a-ftm-alarm" + "fsl,ls1028a-ftm-alarm" + "fsl,ls1043a-ftm-alarm" + "fsl,ls1046a-ftm-alarm" + "fsl,ls1088a-ftm-alarm" + "fsl,ls208xa-ftm-alarm" + "fsl,lx2160a-ftm-alarm" +- reg : Specifies base physical address and size of the register sets for the + FlexTimer Module. +- interrupts : Should be the FlexTimer Module interrupt. +- fsl,rcpm-wakeup property and rcpm node : Please refer + Documentation/devicetree/bindings/soc/fsl/rcpm.txt + +Optional properties: +- big-endian: If the host controller is big-endian mode, specify this property. + The default endian mode is little-endian. + +Example: +rcpm: rcpm@1e34040 { + compatible = "fsl,ls1088a-rcpm", "fsl,qoriq-rcpm-2.1+"; + reg = <0x0 0x1e34040 0x0 0x18>; + #fsl,rcpm-wakeup-cells = <6>; +}; + +ftm_alarm0: timer@2800000 { + compatible = "fsl,ls1088a-ftm-alarm"; + reg = <0x0 0x2800000 0x0 0x10000>; + fsl,rcpm-wakeup = <&rcpm 0x0 0x0 0x0 0x0 0x4000 0x0>; + interrupts = <0 44 4>; +}; diff --git a/Documentation/devicetree/bindings/rtc/rtc-meson-vrtc.txt b/Documentation/devicetree/bindings/rtc/rtc-meson-vrtc.txt new file mode 100644 index 000000000000..c014f54a9853 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/rtc-meson-vrtc.txt @@ -0,0 +1,22 @@ +* Amlogic Virtual RTC (VRTC) + +This is a Linux interface to an RTC managed by firmware, hence it's +virtual from a Linux perspective. The interface is 1 register where +an alarm time (in seconds) is to be written. + +Required properties: +- compatible: should be "amlogic,meson-vrtc" +- reg: physical address for the alarm register + +The alarm register is a simple scratch register shared between the +application processors (AP) and the secure co-processor (SCP.) When +the AP suspends, the SCP will use the value of this register to +program an always-on timer before going sleep. When the timer expires, +the SCP will wake up and will then wake the AP. + +Example: + + vrtc: rtc@0a8 { + compatible = "amlogic,meson-vrtc"; + reg = <0x0 0x000a8 0x0 0x4>; + }; diff --git a/Documentation/devicetree/bindings/rtc/rtc.txt b/Documentation/devicetree/bindings/rtc/rtc.txt index a97fc6a9a75e..b8d36fce5e2d 100644 --- a/Documentation/devicetree/bindings/rtc/rtc.txt +++ b/Documentation/devicetree/bindings/rtc/rtc.txt @@ -1,72 +1 @@ -Generic device tree bindings for Real Time Clock devices -======================================================== - -This document describes generic bindings which can be used to describe Real Time -Clock devices in a device tree. - -Required properties -------------------- - -- compatible : name of RTC device following generic names recommended practice. - -For other required properties e.g. to describe register sets, -clocks, etc. check the binding documentation of the specific driver. - -Optional properties -------------------- - -- start-year : if provided, the default hardware range supported by the RTC is - shifted so the first usable year is the specified one. - -The following properties may not be supported by all drivers. However, if a -driver wants to support one of the below features, it should adapt the bindings -below. -- trickle-resistor-ohms : Selected resistor for trickle charger. Should be given - if trickle charger should be enabled -- trickle-diode-disable : Do not use internal trickle charger diode Should be - given if internal trickle charger diode should be - disabled -- wakeup-source : Enables wake up of host system on alarm -- quartz-load-femtofarads : The capacitive load of the quartz(x-tal), - expressed in femto Farad (fF). - The default value shall be listed (if optional), - and likewise all valid values. - -Trivial RTCs ------------- - -This is a list of trivial RTC devices that have simple device tree -bindings, consisting only of a compatible field, an address and -possibly an interrupt line. - - -Compatible Vendor / Chip -========== ============= -abracon,abb5zes3 AB-RTCMC-32.768kHz-B5ZE-S3: Real Time Clock/Calendar Module with I2C Interface -abracon,abeoz9 AB-RTCMC-32.768kHz-EOZ9: Real Time Clock/Calendar Module with I2C Interface -dallas,ds1374 I2C, 32-Bit Binary Counter Watchdog RTC with Trickle Charger and Reset Input/Output -dallas,ds1672 Dallas DS1672 Real-time Clock -dallas,ds3232 Extremely Accurate I²C RTC with Integrated Crystal and SRAM -epson,rx8010 I2C-BUS INTERFACE REAL TIME CLOCK MODULE -epson,rx8571 I2C-BUS INTERFACE REAL TIME CLOCK MODULE with Battery Backed RAM -epson,rx8581 I2C-BUS INTERFACE REAL TIME CLOCK MODULE -emmicro,em3027 EM Microelectronic EM3027 Real-time Clock -isil,isl1208 Intersil ISL1208 Low Power RTC with Battery Backed SRAM -isil,isl1218 Intersil ISL1218 Low Power RTC with Battery Backed SRAM -isil,isl12022 Intersil ISL12022 Real-time Clock -microcrystal,rv3028 Real Time Clock Module with I2C-Bus -microcrystal,rv3029 Real Time Clock Module with I2C-Bus -microcrystal,rv8523 Real Time Clock -nxp,pcf2127 Real-time clock -nxp,pcf2129 Real-time clock -nxp,pcf8563 Real-time clock/calendar -pericom,pt7c4338 Real-time Clock Module -ricoh,r2025sd I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC -ricoh,r2221tl I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC -ricoh,rs5c372a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC -ricoh,rs5c372b I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC -ricoh,rv5c386 I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC -ricoh,rv5c387a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC -sii,s35390a 2-wire CMOS real-time clock -whwave,sd3078 I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC -xircom,x1205 Xircom X1205 I2C RTC +This file has been moved to rtc.yaml. diff --git a/Documentation/devicetree/bindings/rtc/rtc.yaml b/Documentation/devicetree/bindings/rtc/rtc.yaml new file mode 100644 index 000000000000..ee237b2ed66a --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/rtc.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/rtc/rtc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: RTC Generic Binding + +maintainers: + - Alexandre Belloni <alexandre.belloni@bootlin.com> + +description: | + This document describes generic bindings which can be used to + describe Real Time Clock devices in a device tree. + +properties: + $nodename: + pattern: "^rtc(@.*|-[0-9a-f])*$" + + quartz-load-femtofarads: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + The capacitive load of the quartz(x-tal), expressed in femto + Farad (fF). The default value shall be listed (if optional), + and likewise all valid values. + + start-year: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + If provided, the default hardware range supported by the RTC is + shifted so the first usable year is the specified one. + + trickle-diode-disable: + $ref: /schemas/types.yaml#/definitions/flag + description: + Do not use internal trickle charger diode. Should be given if + internal trickle charger diode should be disabled. + + trickle-resistor-ohms: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Selected resistor for trickle charger. Should be given + if trickle charger should be enabled. + + wakeup-source: + $ref: /schemas/types.yaml#/definitions/flag + description: + Enables wake up of host system on alarm. + +... diff --git a/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt b/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt deleted file mode 100644 index 6b732c41392b..000000000000 --- a/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt +++ /dev/null @@ -1,46 +0,0 @@ -* sun6i Real Time Clock - -RTC controller for the Allwinner A31 - -Required properties: -- compatible : Should be one of the following combinations: - - "allwinner,sun6i-a31-rtc" - - "allwinner,sun8i-a23-rtc" - - "allwinner,sun8i-h3-rtc" - - "allwinner,sun8i-r40-rtc", "allwinner,sun8i-h3-rtc" - - "allwinner,sun8i-v3-rtc" - - "allwinner,sun50i-a64-rtc", "allwinner,sun8i-h3-rtc" - - "allwinner,sun50i-h5-rtc" - - Where there are two or more compatible strings, this - denotes the hardware covered by the most specific one - is backward-compatible with the latter ones, and the - implementation for the latter ones can be used, albeit - with reduced functionality. - -- reg : physical base address of the controller and length of - memory mapped region. -- interrupts : IRQ lines for the RTC alarm 0 and alarm 1, in that order. - -Required properties for new device trees -- clocks : phandle to the 32kHz external oscillator -- clock-output-names : names of up to three clock outputs. See below. -- #clock-cells : must be equal to 1. - -The RTC provides the following clocks at the given indices: -- 0: LOSC -- 1: LOSC external output, known as X32KFOUT in the datasheet. - This clock is not available on the A31 and is deprecated for old - device trees still using the "allwinner,sun6i-a31-rtc" compatible. -- 2: InternalOSC, or internal RC oscillator (A64/H3/H5 only) - -Example: - -rtc: rtc@1f00000 { - compatible = "allwinner,sun6i-a31-rtc"; - reg = <0x01f00000 0x400>; - interrupts = <0 40 4>, <0 41 4>; - clock-output-names = "osc32k"; - clocks = <&ext_osc32k>; - #clock-cells = <1>; -}; diff --git a/Documentation/devicetree/bindings/rtc/sunxi-rtc.txt b/Documentation/devicetree/bindings/rtc/sunxi-rtc.txt deleted file mode 100644 index 4a8d79c1cf08..000000000000 --- a/Documentation/devicetree/bindings/rtc/sunxi-rtc.txt +++ /dev/null @@ -1,17 +0,0 @@ -* sun4i/sun7i Real Time Clock - -RTC controller for the Allwinner A10/A20 - -Required properties: -- compatible : Should be "allwinner,sun4i-a10-rtc" or "allwinner,sun7i-a20-rtc" -- reg: physical base address of the controller and length of memory mapped - region. -- interrupts: IRQ line for the RTC. - -Example: - -rtc: rtc@1c20d00 { - compatible = "allwinner,sun4i-a10-rtc"; - reg = <0x01c20d00 0x20>; - interrupts = <24>; -}; diff --git a/Documentation/devicetree/bindings/rtc/trivial-rtc.yaml b/Documentation/devicetree/bindings/rtc/trivial-rtc.yaml new file mode 100644 index 000000000000..18cb456752f6 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/trivial-rtc.yaml @@ -0,0 +1,90 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/rtc/trivial-rtc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Trivial RTCs + +maintainers: + - Alexandre Belloni <alexandre.belloni@bootlin.com> + +description: | + This is a list of trivial RTC devices that have simple device tree + bindings, consisting only of a compatible field, an address and + possibly an interrupt line. + +allOf: + - $ref: "rtc.yaml#" + +properties: + compatible: + enum: + # AB-RTCMC-32.768kHz-B5ZE-S3: Real Time Clock/Calendar Module with I2C Interface + - abracon,abb5zes3 + # AB-RTCMC-32.768kHz-EOZ9: Real Time Clock/Calendar Module with I2C Interface + - abracon,abeoz9 + # I2C, 32-Bit Binary Counter Watchdog RTC with Trickle Charger and Reset Input/Output + - dallas,ds1374 + # Dallas DS1672 Real-time Clock + - dallas,ds1672 + # Extremely Accurate I²C RTC with Integrated Crystal and SRAM + - dallas,ds3232 + # I2C-BUS INTERFACE REAL TIME CLOCK MODULE + - epson,rx8010 + # I2C-BUS INTERFACE REAL TIME CLOCK MODULE with Battery Backed RAM + - epson,rx8571 + # I2C-BUS INTERFACE REAL TIME CLOCK MODULE + - epson,rx8581 + # Intersil ISL1208 Low Power RTC with Battery Backed SRAM + - isil,isl1208 + # Intersil ISL1218 Low Power RTC with Battery Backed SRAM + - isil,isl1218 + # Intersil ISL12022 Real-time Clock + - isil,isl12022 + # Real Time Clock Module with I2C-Bus + - microcrystal,rv3028 + # Real Time Clock Module with I2C-Bus + - microcrystal,rv3029 + # Real Time Clock + - microcrystal,rv8523 + # Real-time clock + - nxp,pcf2127 + # Real-time clock + - nxp,pcf2129 + # Real-time Clock Module + - pericom,pt7c4338 + # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC + - ricoh,r2025sd + # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC + - ricoh,r2221tl + # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC + - ricoh,rs5c372a + # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC + - ricoh,rs5c372b + # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC + - ricoh,rv5c386 + # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC + - ricoh,rv5c387a + # 2-wire CMOS real-time clock + - sii,s35390a + # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC + - whwave,sd3078 + # Xircom X1205 I2C RTC + - xircom,x1205 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + start-year: true + +required: + - compatible + - reg + +additionalProperties: false + +... diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt index 3cba12f855b7..20d351f268ef 100644 --- a/Documentation/devicetree/bindings/serial/8250.txt +++ b/Documentation/devicetree/bindings/serial/8250.txt @@ -53,6 +53,9 @@ Optional properties: programmable TX FIFO thresholds. - resets : phandle + reset specifier pairs - overrun-throttle-ms : how long to pause uart rx when input overrun is encountered. +- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD + line respectively. It will use specified GPIO instead of the peripheral + function pin for the UART feature. If unsure, don't specify this property. Note: * fsl,ns16550: @@ -74,3 +77,19 @@ Example: interrupts = <10>; reg-shift = <2>; }; + +Example for OMAP UART using GPIO-based modem control signals: + + uart4: serial@49042000 { + compatible = "ti,omap3-uart"; + reg = <0x49042000 0x400>; + interrupts = <80>; + ti,hwmods = "uart4"; + clock-frequency = <48000000>; + cts-gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; + rts-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>; + dtr-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; + dsr-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; + dcd-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; + rng-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/serial/amlogic,meson-uart.txt b/Documentation/devicetree/bindings/serial/amlogic,meson-uart.txt deleted file mode 100644 index c06c045126fc..000000000000 --- a/Documentation/devicetree/bindings/serial/amlogic,meson-uart.txt +++ /dev/null @@ -1,38 +0,0 @@ -Amlogic Meson SoC UART Serial Interface -======================================= - -The Amlogic Meson SoC UART Serial Interface is present on a large range -of SoCs, and can be present either in the "Always-On" power domain or the -"Everything-Else" power domain. - -The particularity of the "Always-On" Serial Interface is that the hardware -is active since power-on and does not need any clock gating and is usable -as very early serial console. - -Required properties: -- compatible : compatible: value should be different for each SoC family as : - - Meson6 : "amlogic,meson6-uart" - - Meson8 : "amlogic,meson8-uart" - - Meson8b : "amlogic,meson8b-uart" - - GX (GXBB, GXL, GXM) : "amlogic,meson-gx-uart" - eventually followed by : "amlogic,meson-ao-uart" if this UART interface - is in the "Always-On" power domain. -- reg : offset and length of the register set for the device. -- interrupts : identifier to the device interrupt -- clocks : a list of phandle + clock-specifier pairs, one for each - entry in clock names. -- clock-names : - * "xtal" for external xtal clock identifier - * "pclk" for the bus core clock, either the clk81 clock or the gate clock - * "baud" for the source of the baudrate generator, can be either the xtal - or the pclk. - -e.g. -uart_A: serial@84c0 { - compatible = "amlogic,meson-gx-uart"; - reg = <0x0 0x84c0 0x0 0x14>; - interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>; - /* Use xtal as baud rate clock source */ - clocks = <&xtal>, <&clkc CLKID_UART0>, <&xtal>; - clock-names = "xtal", "pclk", "baud"; -}; diff --git a/Documentation/devicetree/bindings/serial/amlogic,meson-uart.yaml b/Documentation/devicetree/bindings/serial/amlogic,meson-uart.yaml new file mode 100644 index 000000000000..214fe8beddc3 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/amlogic,meson-uart.yaml @@ -0,0 +1,73 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 BayLibre, SAS +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/serial/amlogic,meson-uart.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Amlogic Meson SoC UART Serial Interface + +maintainers: + - Neil Armstrong <narmstrong@baylibre.com> + +description: | + The Amlogic Meson SoC UART Serial Interface is present on a large range + of SoCs, and can be present either in the "Always-On" power domain or the + "Everything-Else" power domain. + + The particularity of the "Always-On" Serial Interface is that the hardware + is active since power-on and does not need any clock gating and is usable + as very early serial console. + +properties: + compatible: + oneOf: + - description: Always-on power domain UART controller + items: + - enum: + - amlogic,meson6-uart + - amlogic,meson8-uart + - amlogic,meson8b-uart + - amlogic,meson-gx-uart + - const: amlogic,meson-ao-uart + - description: Everything-Else power domain UART controller + enum: + - amlogic,meson6-uart + - amlogic,meson8-uart + - amlogic,meson8b-uart + - amlogic,meson-gx-uart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: external xtal clock identifier + - description: the bus core clock, either the clk81 clock or the gate clock + - description: the source of the baudrate generator, can be either the xtal or the pclk + + clock-names: + items: + - const: xtal + - const: pclk + - const: baud + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +examples: + - | + serial@84c0 { + compatible = "amlogic,meson-gx-uart"; + reg = <0x84c0 0x14>; + interrupts = <26>; + clocks = <&xtal>, <&pclk>, <&xtal>; + clock-names = "xtal", "pclk", "baud"; + }; diff --git a/Documentation/devicetree/bindings/serial/fsl,s32-linflexuart.txt b/Documentation/devicetree/bindings/serial/fsl,s32-linflexuart.txt new file mode 100644 index 000000000000..f1bbe0826be5 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/fsl,s32-linflexuart.txt @@ -0,0 +1,22 @@ +* Freescale LINFlexD UART + +The LINFlexD controller implements several LIN protocol versions, as well as +support for full-duplex UART communication through 8-bit and 9-bit frames. + +See chapter 47 ("LINFlexD") in the reference manual[1]. + +Required properties: +- compatible : + - "fsl,s32v234-linflexuart" for LINFlexD configured in UART mode, which + is compatible with the one integrated on S32V234 SoC +- reg : Address and length of the register set for the device +- interrupts : Should contain uart interrupt + +Example: +uart0: serial@40053000 { + compatible = "fsl,s32v234-linflexuart"; + reg = <0x0 0x40053000 0x0 0x1000>; + interrupts = <0 59 4>; +}; + +[1] https://www.nxp.com/webapp/Download?colCode=S32V234RM diff --git a/Documentation/devicetree/bindings/serial/fsl-lpuart.txt b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt index 21483ba820bc..3495eee81d53 100644 --- a/Documentation/devicetree/bindings/serial/fsl-lpuart.txt +++ b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt @@ -13,7 +13,10 @@ Required properties: - reg : Address and length of the register set for the device - interrupts : Should contain uart interrupt - clocks : phandle + clock specifier pairs, one for each entry in clock-names -- clock-names : should contain: "ipg" - the uart clock +- clock-names : For vf610/ls1021a/imx7ulp, "ipg" clock is for uart bus/baud + clock. For imx8qxp lpuart, "ipg" clock is bus clock that is used to access + lpuart controller registers, it also requires "baud" clock for module to + receive/transmit data. Optional properties: - dmas: A list of two dma specifiers, one for each entry in dma-names. diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt index c6b5262eb352..3a3b57079f0d 100644 --- a/Documentation/devicetree/bindings/serial/mtk-uart.txt +++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt @@ -9,6 +9,7 @@ Required properties: * "mediatek,mt6589-uart" for MT6589 compatible UARTS * "mediatek,mt6755-uart" for MT6755 compatible UARTS * "mediatek,mt6765-uart" for MT6765 compatible UARTS + * "mediatek,mt6779-uart" for MT6779 compatible UARTS * "mediatek,mt6795-uart" for MT6795 compatible UARTS * "mediatek,mt6797-uart" for MT6797 compatible UARTS * "mediatek,mt7622-uart" for MT7622 compatible UARTS @@ -23,7 +24,12 @@ Required properties: - reg: The base address of the UART register bank. -- interrupts: A single interrupt specifier. +- interrupts: + index 0: an interrupt specifier for the UART controller itself + index 1: optional, an interrupt specifier with edge sensitivity on Rx pin to + support Rx in-band wake up. If one would like to use this feature, + one must create an addtional pinctrl to reconfigure Rx pin to normal + GPIO before suspend. - clocks : Must contain an entry for each entry in clock-names. See ../clocks/clock-bindings.txt for details. @@ -39,7 +45,11 @@ Example: uart0: serial@11006000 { compatible = "mediatek,mt6589-uart", "mediatek,mt6577-uart"; reg = <0x11006000 0x400>; - interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 52 IRQ_TYPE_EDGE_FALLING>; clocks = <&uart_clk>, <&bus_clk>; clock-names = "baud", "bus"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&uart_pin>; + pinctrl-1 = <&uart_pin_sleep>; }; diff --git a/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt index d7edf732eb7f..f709304036c2 100644 --- a/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt +++ b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt @@ -1,7 +1,12 @@ NVIDIA Tegra20/Tegra30 high speed (DMA based) UART controller driver. Required properties: -- compatible : should be "nvidia,tegra30-hsuart", "nvidia,tegra20-hsuart". +- compatible : should be, + "nvidia,tegra20-hsuart" for Tegra20, + "nvidia,tegra30-hsuart" for Tegra30, + "nvidia,tegra186-hsuart" for Tegra186, + "nvidia,tegra194-hsuart" for Tegra194. + - reg: Should contain UART controller registers location and length. - interrupts: Should contain UART controller interrupts. - clocks: Must contain one entry, for the module clock. @@ -19,6 +24,37 @@ Required properties: Optional properties: - nvidia,enable-modem-interrupt: Enable modem interrupts. Should be enable only if all 8 lines of UART controller are pinmuxed. +- nvidia,adjust-baud-rates: List of entries providing percentage of baud rate + adjustment within a range. + Each entry contains sets of 3 values. Range low/high and adjusted rate. + <range_low range_high adjusted_rate> + When baud rate set on controller falls within the range mentioned in this + field, baud rate will be adjusted by percentage mentioned here. + Ex: <9600 115200 200> + Increase baud rate by 2% when set baud rate falls within range 9600 to 115200 + +Baud Rate tolerance: + Standard UART devices are expected to have tolerance for baud rate error by + -4 to +4 %. All Tegra devices till Tegra210 had this support. However, + Tegra186 chip has a known hardware issue. UART Rx baud rate tolerance level + is 0% to +4% in 1-stop config. Otherwise, the received data will have + corruption/invalid framing errors. Parker errata suggests adjusting baud + rate to be higher than the deviations observed in Tx. + + Tx deviation of connected device can be captured over scope (or noted from + its spec) for valid range and Tegra baud rate has to be set above actual + Tx baud rate observed. To do this we use nvidia,adjust-baud-rates + + As an example, consider there is deviation observed in Tx for baud rates as + listed below. + 0 to 9600 has 1% deviation + 9600 to 115200 2% deviation + This slight deviation is expcted and Tegra UART is expected to handle it. Due + to the issue stated above, baud rate on Tegra UART should be set equal to or + above deviation observed for avoiding frame errors. + Property should be set like this + nvidia,adjust-baud-rates = <0 9600 100>, + <9600 115200 200>; Example: @@ -33,4 +69,5 @@ serial@70006000 { reset-names = "serial"; dmas = <&apbdma 8>, <&apbdma 8>; dma-names = "rx", "tx"; + nvidia,adjust-baud-rates = <1000000 4000000 136>; /* 1.36% shift */ }; diff --git a/Documentation/devicetree/bindings/serial/omap_serial.txt b/Documentation/devicetree/bindings/serial/omap_serial.txt index 0a9b5444f4e6..dcba86b0a0d0 100644 --- a/Documentation/devicetree/bindings/serial/omap_serial.txt +++ b/Documentation/devicetree/bindings/serial/omap_serial.txt @@ -1,6 +1,7 @@ OMAP UART controller Required properties: +- compatible : should be "ti,j721e-uart", "ti,am654-uart" for J721E controllers - compatible : should be "ti,am654-uart" for AM654 controllers - compatible : should be "ti,omap2-uart" for OMAP2 controllers - compatible : should be "ti,omap3-uart" for OMAP3 controllers diff --git a/Documentation/devicetree/bindings/serial/sifive-serial.txt b/Documentation/devicetree/bindings/serial/sifive-serial.txt deleted file mode 100644 index c86b1e524159..000000000000 --- a/Documentation/devicetree/bindings/serial/sifive-serial.txt +++ /dev/null @@ -1,33 +0,0 @@ -SiFive asynchronous serial interface (UART) - -Required properties: - -- compatible: should be something similar to - "sifive,<chip>-uart" for the UART as integrated - on a particular chip, and "sifive,uart<version>" for the - general UART IP block programming model. Supported - compatible strings as of the date of this writing are: - "sifive,fu540-c000-uart" for the SiFive UART v0 as - integrated onto the SiFive FU540 chip, or "sifive,uart0" - for the SiFive UART v0 IP block with no chip integration - tweaks (if any) -- reg: address and length of the register space -- interrupts: Should contain the UART interrupt identifier -- clocks: Should contain a clock identifier for the UART's parent clock - - -UART HDL that corresponds to the IP block version numbers can be found -here: - -https://github.com/sifive/sifive-blocks/tree/master/src/main/scala/devices/uart - - -Example: - -uart0: serial@10010000 { - compatible = "sifive,fu540-c000-uart", "sifive,uart0"; - interrupt-parent = <&plic0>; - interrupts = <80>; - reg = <0x0 0x10010000 0x0 0x1000>; - clocks = <&prci PRCI_CLK_TLCLK>; -}; diff --git a/Documentation/devicetree/bindings/serial/sifive-serial.yaml b/Documentation/devicetree/bindings/serial/sifive-serial.yaml new file mode 100644 index 000000000000..e8d3aeda1202 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/sifive-serial.yaml @@ -0,0 +1,62 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/sifive-serial.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SiFive asynchronous serial interface (UART) + +maintainers: + - Pragnesh Patel <pragnesh.patel@sifive.com> + - Paul Walmsley <paul.walmsley@sifive.com> + - Palmer Dabbelt <palmer@sifive.com> + +allOf: + - $ref: /schemas/serial.yaml# + +properties: + compatible: + items: + - const: sifive,fu540-c000-uart + - const: sifive,uart0 + + description: + Should be something similar to "sifive,<chip>-uart" + for the UART as integrated on a particular chip, + and "sifive,uart<version>" for the general UART IP + block programming model. + + UART HDL that corresponds to the IP block version + numbers can be found here - + + https://github.com/sifive/sifive-blocks/tree/master/src/main/scala/devices/uart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/sifive-fu540-prci.h> + serial@10010000 { + compatible = "sifive,fu540-c000-uart", "sifive,uart0"; + interrupt-parent = <&plic0>; + interrupts = <80>; + reg = <0x0 0x10010000 0x0 0x1000>; + clocks = <&prci PRCI_CLK_TLCLK>; + }; + +... diff --git a/Documentation/devicetree/bindings/serial/st,stm32-usart.txt b/Documentation/devicetree/bindings/serial/st,stm32-usart.txt index 9d3efed55deb..8620f7fcbd50 100644 --- a/Documentation/devicetree/bindings/serial/st,stm32-usart.txt +++ b/Documentation/devicetree/bindings/serial/st,stm32-usart.txt @@ -13,12 +13,18 @@ Required properties: - clocks: The input clock of the USART instance Optional properties: +- resets: Must contain the phandle to the reset controller. - pinctrl: The reference on the pins configuration - st,hw-flow-ctrl: bool flag to enable hardware flow control. - rs485-rts-delay, rs485-rx-during-tx, rs485-rts-active-low, linux,rs485-enabled-at-boot-time: see rs485.txt. - dmas: phandle(s) to DMA controller node(s). Refer to stm32-dma.txt - dma-names: "rx" and/or "tx" +- wakeup-source: bool flag to indicate this device has wakeup capabilities +- interrupt-names, if optional wake-up interrupt is used, should be: + - "event": the name for the interrupt line of the USART instance + - "wakeup" the name for the optional wake-up interrupt + Examples: usart4: serial@40004c00 { diff --git a/Documentation/devicetree/bindings/soc/amlogic/amlogic,canvas.txt b/Documentation/devicetree/bindings/soc/amlogic/amlogic,canvas.txt index 436d2106e80d..e876f3ce54f6 100644 --- a/Documentation/devicetree/bindings/soc/amlogic/amlogic,canvas.txt +++ b/Documentation/devicetree/bindings/soc/amlogic/amlogic,canvas.txt @@ -2,8 +2,8 @@ Amlogic Canvas ================================ A canvas is a collection of metadata that describes a pixel buffer. -Those metadata include: width, height, phyaddr, wrapping, block mode -and endianness. +Those metadata include: width, height, phyaddr, wrapping and block mode. +Starting with GXBB the endianness can also be described. Many IPs within Amlogic SoCs rely on canvas indexes to read/write pixel data rather than use the phy addresses directly. For instance, this is the case for @@ -18,7 +18,11 @@ Video Lookup Table -------------------------- Required properties: -- compatible: "amlogic,canvas" +- compatible: has to be one of: + - "amlogic,meson8-canvas", "amlogic,canvas" on Meson8 + - "amlogic,meson8b-canvas", "amlogic,canvas" on Meson8b + - "amlogic,meson8m2-canvas", "amlogic,canvas" on Meson8m2 + - "amlogic,canvas" on GXBB and newer - reg: Base physical address and size of the canvas registers. Example: diff --git a/Documentation/devicetree/bindings/soc/amlogic/clk-measure.txt b/Documentation/devicetree/bindings/soc/amlogic/clk-measure.txt index 6bf6b43f8dd8..3dd563cec794 100644 --- a/Documentation/devicetree/bindings/soc/amlogic/clk-measure.txt +++ b/Documentation/devicetree/bindings/soc/amlogic/clk-measure.txt @@ -11,6 +11,7 @@ Required properties: "amlogic,meson8b-clk-measure" for Meson8b SoCs "amlogic,meson-axg-clk-measure" for AXG SoCs "amlogic,meson-g12a-clk-measure" for G12a SoCs + "amlogic,meson-sm1-clk-measure" for SM1 SoCs - reg: base address and size of the Clock Measurer register space. Example: diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt index d7afaff5faff..05ec2a838c54 100644 --- a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt @@ -18,7 +18,8 @@ Required properties: - reg : offset and length of the device registers. - bus-frequency : the clock frequency for QUICC Engine. - fsl,qe-num-riscs: define how many RISC engines the QE has. -- fsl,qe-num-snums: define how many serial number(SNUM) the QE can use for the +- fsl,qe-snums: This property has to be specified as '/bits/ 8' value, + defining the array of serial number (SNUM) values for the virtual threads. Optional properties: @@ -34,6 +35,11 @@ Recommended properties - brg-frequency : the internal clock source frequency for baud-rate generators in Hz. +Deprecated properties +- fsl,qe-num-snums: define how many serial number(SNUM) the QE can use + for the threads. Use fsl,qe-snums instead to not only specify the + number of snums, but also their values. + Example: qe@e0100000 { #address-cells = <1>; @@ -44,6 +50,11 @@ Example: reg = <e0100000 480>; brg-frequency = <0>; bus-frequency = <179A7B00>; + fsl,qe-snums = /bits/ 8 < + 0x04 0x05 0x0C 0x0D 0x14 0x15 0x1C 0x1D + 0x24 0x25 0x2C 0x2D 0x34 0x35 0x88 0x89 + 0x98 0x99 0xA8 0xA9 0xB8 0xB9 0xC8 0xC9 + 0xD8 0xD9 0xE8 0xE9>; } * Multi-User RAM (MURAM) diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,aoss-qmp.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,aoss-qmp.txt new file mode 100644 index 000000000000..4fc571e78f01 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,aoss-qmp.txt @@ -0,0 +1,84 @@ +Qualcomm Always-On Subsystem side channel binding + +This binding describes the hardware component responsible for side channel +requests to the always-on subsystem (AOSS), used for certain power management +requests that is not handled by the standard RPMh interface. Each client in the +SoC has it's own block of message RAM and IRQ for communication with the AOSS. +The protocol used to communicate in the message RAM is known as Qualcomm +Messaging Protocol (QMP) + +The AOSS side channel exposes control over a set of resources, used to control +a set of debug related clocks and to affect the low power state of resources +related to the secondary subsystems. These resources are exposed as a set of +power-domains. + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,sc7180-aoss-qmp" + "qcom,sdm845-aoss-qmp" + "qcom,sm8150-aoss-qmp" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the message RAM for this + client's communication with the AOSS + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the AOSS message IRQ for this client + +- mboxes: + Usage: required + Value type: <prop-encoded-array> + Definition: reference to the mailbox representing the outgoing doorbell + in APCS for this client, as described in mailbox/mailbox.txt + +- #clock-cells: + Usage: optional + Value type: <u32> + Definition: must be 0 + The single clock represents the QDSS clock. + +- #power-domain-cells: + Usage: optional + Value type: <u32> + Definition: must be 1 + The provided power-domains are: + CDSP state (0), LPASS state (1), modem state (2), SLPI + state (3), SPSS state (4) and Venus state (5). + += SUBNODES +The AOSS side channel also provides the controls for three cooling devices, +these are expressed as subnodes of the QMP node. The name of the node is used +to identify the resource and must therefor be "cx", "mx" or "ebi". + +- #cooling-cells: + Usage: optional + Value type: <u32> + Definition: must be 2 + += EXAMPLE + +The following example represents the AOSS side-channel message RAM and the +mechanism exposing the power-domains, as found in SDM845. + + aoss_qmp: qmp@c300000 { + compatible = "qcom,sdm845-aoss-qmp"; + reg = <0x0c300000 0x100000>; + interrupts = <GIC_SPI 389 IRQ_TYPE_EDGE_RISING>; + mboxes = <&apss_shared 0>; + + #power-domain-cells = <1>; + + cx_cdev: cx { + #cooling-cells = <2>; + }; + + mx_cdev: mx { + #cooling-cells = <2>; + }; + }; diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt index bcc612cc7423..db501269f47b 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt @@ -9,7 +9,7 @@ used for audio/voice services on the QDSP. Value type: <stringlist> Definition: must be "qcom,apr-v<VERSION-NUMBER>", example "qcom,apr-v2" -- reg +- qcom,apr-domain Usage: required Value type: <u32> Definition: Destination processor ID. @@ -49,9 +49,9 @@ by the individual bindings for the specific service The following example represents a QDSP based sound card on a MSM8996 device which uses apr as communication between Apps and QDSP. - apr@4 { + apr { compatible = "qcom,apr-v2"; - reg = <APR_DOMAIN_ADSP>; + qcom,apr-domain = <APR_DOMAIN_ADSP>; q6core@3 { compatible = "qcom,q6core"; diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt index cf759e5f9b10..1214192847ac 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt @@ -21,6 +21,11 @@ edge. Definition: should specify the IRQ used by the remote processor to signal this processor about communication related events +- qcom,remote-pid: + Usage: required for glink-smem + Value type: <u32> + Definition: specifies the identifier of the remote endpoint of this edge + - qcom,rpm-msg-ram: Usage: required for glink-rpm Value type: <prop-encoded-array> diff --git a/Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt b/Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt index f7b00a7c0f68..f541d1f776a2 100644 --- a/Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt +++ b/Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt @@ -19,8 +19,15 @@ child of the pmmc node. Required Properties: -------------------- - compatible: should be "ti,sci-pm-domain" -- #power-domain-cells: Must be 1 so that an id can be provided in each - device node. +- #power-domain-cells: Can be one of the following: + 1: Containing the device id of each node + 2: First entry should be device id + Second entry should be one of the floowing: + TI_SCI_PD_EXCLUSIVE: To allow device to be + exclusively controlled by + the requesting hosts. + TI_SCI_PD_SHARED: To allow device to be shared + by multiple hosts. Example (K2G): ------------- diff --git a/Documentation/devicetree/bindings/sound/allwinner,sun4i-a10-i2s.yaml b/Documentation/devicetree/bindings/sound/allwinner,sun4i-a10-i2s.yaml new file mode 100644 index 000000000000..eb3992138eec --- /dev/null +++ b/Documentation/devicetree/bindings/sound/allwinner,sun4i-a10-i2s.yaml @@ -0,0 +1,132 @@ +# SPDX-License-Identifier: (GPL-2.0+ OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/allwinner,sun4i-a10-i2s.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 I2S Controller Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + "#sound-dai-cells": + const: 0 + + compatible: + oneOf: + - const: allwinner,sun4i-a10-i2s + - const: allwinner,sun6i-a31-i2s + - const: allwinner,sun8i-a83t-i2s + - const: allwinner,sun8i-h3-i2s + - const: allwinner,sun50i-a64-codec-i2s + - items: + - const: allwinner,sun50i-a64-i2s + - const: allwinner,sun8i-h3-i2s + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Bus Clock + - description: Module Clock + + clock-names: + items: + - const: apb + - const: mod + + # Even though it only applies to subschemas under the conditionals, + # not listing them here will trigger a warning because of the + # additionalsProperties set to false. + dmas: true + dma-names: true + resets: + maxItems: 1 + +allOf: + - if: + properties: + compatible: + contains: + enum: + - allwinner,sun6i-a31-i2s + - allwinner,sun8i-a83t-i2s + - allwinner,sun8i-h3-i2s + - allwinner,sun50i-a64-codec-i2s + + then: + required: + - resets + + - if: + properties: + compatible: + contains: + const: allwinner,sun8i-a83t-i2s + + then: + properties: + dmas: + minItems: 1 + maxItems: 2 + items: + - description: RX DMA Channel + - description: TX DMA Channel + description: + Some controllers cannot receive but can only transmit + data. In such a case, the RX DMA channel is to be omitted. + + dma-names: + oneOf: + - items: + - const: rx + - const: tx + - const: tx + description: + Some controllers cannot receive but can only transmit + data. In such a case, the RX name is to be omitted. + + else: + properties: + dmas: + items: + - description: RX DMA Channel + - description: TX DMA Channel + + dma-names: + items: + - const: rx + - const: tx + +required: + - "#sound-dai-cells" + - compatible + - reg + - interrupts + - clocks + - clock-names + - dmas + - dma-names + +additionalProperties: false + +examples: + - | + i2s0: i2s@1c22400 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun4i-a10-i2s"; + reg = <0x01c22400 0x400>; + interrupts = <0 16 4>; + clocks = <&apb0_gates 3>, <&i2s0_clk>; + clock-names = "apb", "mod"; + dmas = <&dma 0 3>, <&dma 0 3>; + dma-names = "rx", "tx"; + }; + +... diff --git a/Documentation/devicetree/bindings/sound/allwinner,sun4i-a10-spdif.yaml b/Documentation/devicetree/bindings/sound/allwinner,sun4i-a10-spdif.yaml new file mode 100644 index 000000000000..38d4cede0860 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/allwinner,sun4i-a10-spdif.yaml @@ -0,0 +1,122 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/allwinner,sun4i-a10-spdif.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 S/PDIF Controller Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Liam Girdwood <lgirdwood@gmail.com> + - Mark Brown <broonie@kernel.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + "#sound-dai-cells": + const: 0 + + compatible: + oneOf: + - const: allwinner,sun4i-a10-spdif + - const: allwinner,sun6i-a31-spdif + - const: allwinner,sun8i-h3-spdif + - const: allwinner,sun50i-h6-spdif + - items: + - const: allwinner,sun8i-a83t-spdif + - const: allwinner,sun8i-h3-spdif + - items: + - const: allwinner,sun50i-a64-spdif + - const: allwinner,sun8i-h3-spdif + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Bus Clock + - description: Module Clock + + clock-names: + items: + - const: apb + - const: spdif + + # Even though it only applies to subschemas under the conditionals, + # not listing them here will trigger a warning because of the + # additionalsProperties set to false. + dmas: true + dma-names: true + resets: + maxItems: 1 + +allOf: + - if: + properties: + compatible: + contains: + enum: + - allwinner,sun6i-a31-spdif + - allwinner,sun8i-h3-spdif + + then: + required: + - resets + + - if: + properties: + compatible: + contains: + enum: + - allwinner,sun8i-h3-spdif + - allwinner,sun50i-h6-spdif + + then: + properties: + dmas: + description: TX DMA Channel + + dma-names: + const: tx + + else: + properties: + dmas: + items: + - description: RX DMA Channel + - description: TX DMA Channel + + dma-names: + items: + - const: rx + - const: tx + +required: + - "#sound-dai-cells" + - compatible + - reg + - interrupts + - clocks + - clock-names + - dmas + - dma-names + +additionalProperties: false + +examples: + - | + spdif: spdif@1c21000 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun4i-a10-spdif"; + reg = <0x01c21000 0x40>; + interrupts = <13>; + clocks = <&apb0_gates 1>, <&spdif_clk>; + clock-names = "apb", "spdif"; + dmas = <&dma 0 2>, <&dma 0 2>; + dma-names = "rx", "tx"; + }; + +... diff --git a/Documentation/devicetree/bindings/sound/allwinner,sun50i-a64-codec-analog.yaml b/Documentation/devicetree/bindings/sound/allwinner,sun50i-a64-codec-analog.yaml new file mode 100644 index 000000000000..f290eb72a878 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/allwinner,sun50i-a64-codec-analog.yaml @@ -0,0 +1,39 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/allwinner,sun50i-a64-codec-analog.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A64 Analog Codec Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + compatible: + const: allwinner,sun50i-a64-codec-analog + + reg: + maxItems: 1 + + cpvdd-supply: + description: + Regulator for the headphone amplifier + +required: + - compatible + - reg + - cpvdd-supply + +additionalProperties: false + +examples: + - | + codec_analog: codec-analog@1f015c0 { + compatible = "allwinner,sun50i-a64-codec-analog"; + reg = <0x01f015c0 0x4>; + cpvdd-supply = <®_eldo1>; + }; + +... diff --git a/Documentation/devicetree/bindings/sound/allwinner,sun8i-a33-codec.yaml b/Documentation/devicetree/bindings/sound/allwinner,sun8i-a33-codec.yaml new file mode 100644 index 000000000000..5e7cc05bbff1 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/allwinner,sun8i-a33-codec.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/allwinner,sun8i-a33-codec.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A33 Codec Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + "#sound-dai-cells": + const: 0 + + compatible: + const: allwinner,sun8i-a33-codec + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Bus Clock + - description: Module Clock + + clock-names: + items: + - const: bus + - const: mod + +required: + - "#sound-dai-cells" + - compatible + - reg + - interrupts + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + audio-codec@1c22e00 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun8i-a33-codec"; + reg = <0x01c22e00 0x400>; + interrupts = <0 29 4>; + clocks = <&ccu 47>, <&ccu 92>; + clock-names = "bus", "mod"; + }; + +... diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-fifo.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-fifo.txt index 4330fc9dca6d..3080979350a0 100644 --- a/Documentation/devicetree/bindings/sound/amlogic,axg-fifo.txt +++ b/Documentation/devicetree/bindings/sound/amlogic,axg-fifo.txt @@ -4,13 +4,18 @@ Required properties: - compatible: 'amlogic,axg-toddr' or 'amlogic,axg-toddr' or 'amlogic,g12a-frddr' or - 'amlogic,g12a-toddr' + 'amlogic,g12a-toddr' or + 'amlogic,sm1-frddr' or + 'amlogic,sm1-toddr' - reg: physical base address of the controller and length of memory mapped region. - interrupts: interrupt specifier for the fifo. - clocks: phandle to the fifo peripheral clock provided by the audio clock controller. -- resets: phandle to memory ARB line provided by the arb reset controller. +- resets: list of reset phandle, one for each entry reset-names. +- reset-names: should contain the following: + * "arb" : memory ARB line (required) + * "rst" : dedicated device reset line (optional) - #sound-dai-cells: must be 0. Example of FRDDR A on the A113 SoC: diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-pdm.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-pdm.txt index 73f473a9365f..716878107a24 100644 --- a/Documentation/devicetree/bindings/sound/amlogic,axg-pdm.txt +++ b/Documentation/devicetree/bindings/sound/amlogic,axg-pdm.txt @@ -2,7 +2,8 @@ Required properties: - compatible: 'amlogic,axg-pdm' or - 'amlogic,g12a-pdm' + 'amlogic,g12a-pdm' or + 'amlogic,sm1-pdm' - reg: physical base address of the controller and length of memory mapped region. - clocks: list of clock phandle, one for each entry clock-names. @@ -12,6 +13,9 @@ Required properties: * "sysclk" : dsp system clock - #sound-dai-cells: must be 0. +Optional property: +- resets: phandle to the dedicated reset line of the pdm input. + Example of PDM on the A113 SoC: pdm: audio-controller@ff632000 { diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-spdifin.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-spdifin.txt index 0b82504fa419..df92a4ecf288 100644 --- a/Documentation/devicetree/bindings/sound/amlogic,axg-spdifin.txt +++ b/Documentation/devicetree/bindings/sound/amlogic,axg-spdifin.txt @@ -2,7 +2,8 @@ Required properties: - compatible: 'amlogic,axg-spdifin' or - 'amlogic,g12a-spdifin' + 'amlogic,g12a-spdifin' or + 'amlogic,sm1-spdifin' - interrupts: interrupt specifier for the spdif input. - clocks: list of clock phandle, one for each entry clock-names. - clock-names: should contain the following: @@ -10,6 +11,9 @@ Required properties: * "refclk" : spdif input reference clock - #sound-dai-cells: must be 0. +Optional property: +- resets: phandle to the dedicated reset line of the spdif input. + Example on the A113 SoC: spdifin: audio-controller@400 { diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-spdifout.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-spdifout.txt index 826152730508..28381dd1f633 100644 --- a/Documentation/devicetree/bindings/sound/amlogic,axg-spdifout.txt +++ b/Documentation/devicetree/bindings/sound/amlogic,axg-spdifout.txt @@ -2,13 +2,17 @@ Required properties: - compatible: 'amlogic,axg-spdifout' or - 'amlogic,g12a-spdifout' + 'amlogic,g12a-spdifout' or + 'amlogic,sm1-spdifout' - clocks: list of clock phandle, one for each entry clock-names. - clock-names: should contain the following: * "pclk" : peripheral clock. * "mclk" : master clock - #sound-dai-cells: must be 0. +Optional property: +- resets: phandle to the dedicated reset line of the spdif output. + Example on the A113 SoC: spdifout: audio-controller@480 { diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-tdm-formatters.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-tdm-formatters.txt index 3b94a715a0b9..5996c0cd89c2 100644 --- a/Documentation/devicetree/bindings/sound/amlogic,axg-tdm-formatters.txt +++ b/Documentation/devicetree/bindings/sound/amlogic,axg-tdm-formatters.txt @@ -4,7 +4,9 @@ Required properties: - compatible: 'amlogic,axg-tdmin' or 'amlogic,axg-tdmout' or 'amlogic,g12a-tdmin' or - 'amlogic,g12a-tdmout' + 'amlogic,g12a-tdmout' or + 'amlogic,sm1-tdmin' or + 'amlogic,sm1-tdmout - reg: physical base address of the controller and length of memory mapped region. - clocks: list of clock phandle, one for each entry clock-names. @@ -15,11 +17,15 @@ Required properties: * "lrclk" : sample clock * "lrclk_sel": sample clock input multiplexer -Example of TDMOUT_A on the A113 SoC: +Optional property: +- resets: phandle to the dedicated reset line of the tdm formatter. + +Example of TDMOUT_A on the S905X2 SoC: tdmout_a: audio-controller@500 { compatible = "amlogic,axg-tdmout"; reg = <0x0 0x500 0x0 0x40>; + resets = <&clkc_audio AUD_RESET_TDMOUT_A>; clocks = <&clkc_audio AUD_CLKID_TDMOUT_A>, <&clkc_audio AUD_CLKID_TDMOUT_A_SCLK>, <&clkc_audio AUD_CLKID_TDMOUT_A_SCLK_SEL>, diff --git a/Documentation/devicetree/bindings/sound/amlogic,g12a-tohdmitx.txt b/Documentation/devicetree/bindings/sound/amlogic,g12a-tohdmitx.txt new file mode 100644 index 000000000000..4e8cd7eb7cec --- /dev/null +++ b/Documentation/devicetree/bindings/sound/amlogic,g12a-tohdmitx.txt @@ -0,0 +1,58 @@ +* Amlogic HDMI Tx control glue + +Required properties: +- compatible: "amlogic,g12a-tohdmitx" or + "amlogic,sm1-tohdmitx" +- reg: physical base address of the controller and length of memory + mapped region. +- #sound-dai-cells: should be 1. +- resets: phandle to the dedicated reset line of the hdmitx glue. + +Example on the S905X2 SoC: + +tohdmitx: audio-controller@744 { + compatible = "amlogic,g12a-tohdmitx"; + reg = <0x0 0x744 0x0 0x4>; + #sound-dai-cells = <1>; + resets = <&clkc_audio AUD_RESET_TOHDMITX>; +}; + +Example of an 'amlogic,axg-sound-card': + +sound { + compatible = "amlogic,axg-sound-card"; + +[...] + + dai-link-x { + sound-dai = <&tdmif_a>; + dai-format = "i2s"; + dai-tdm-slot-tx-mask-0 = <1 1>; + + codec-0 { + sound-dai = <&tohdmitx TOHDMITX_I2S_IN_A>; + }; + + codec-1 { + sound-dai = <&external_dac>; + }; + }; + + dai-link-y { + sound-dai = <&tdmif_c>; + dai-format = "i2s"; + dai-tdm-slot-tx-mask-0 = <1 1>; + + codec { + sound-dai = <&tohdmitx TOHDMITX_I2S_IN_C>; + }; + }; + + dai-link-z { + sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>; + + codec { + sound-dai = <&hdmi_tx>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/cs42l73.txt b/Documentation/devicetree/bindings/sound/cs42l73.txt index 80ae910dbf6c..47b868b5ab01 100644 --- a/Documentation/devicetree/bindings/sound/cs42l73.txt +++ b/Documentation/devicetree/bindings/sound/cs42l73.txt @@ -19,4 +19,4 @@ codec: cs42l73@4a { reg = <0x4a>; reset_gpio = <&gpio 10 0>; chgfreq = <0x05>; -};
\ No newline at end of file +}; diff --git a/Documentation/devicetree/bindings/sound/cs42xx8.txt b/Documentation/devicetree/bindings/sound/cs42xx8.txt index 8619a156d038..bbfe39347c20 100644 --- a/Documentation/devicetree/bindings/sound/cs42xx8.txt +++ b/Documentation/devicetree/bindings/sound/cs42xx8.txt @@ -14,6 +14,11 @@ Required properties: - VA-supply, VD-supply, VLS-supply, VLC-supply: power supplies for the device, as covered in Documentation/devicetree/bindings/regulator/regulator.txt +Optional properties: + + - reset-gpios : a GPIO spec to define which pin is connected to the chip's + !RESET pin + Example: cs42888: codec@48 { @@ -25,4 +30,5 @@ cs42888: codec@48 { VD-supply = <®_audio>; VLS-supply = <®_audio>; VLC-supply = <®_audio>; + reset-gpios = <&pca9557_b 1 GPIO_ACTIVE_LOW>; }; diff --git a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt index a58f79f5345c..c483dcec01f8 100644 --- a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt +++ b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt @@ -44,6 +44,9 @@ Optional properties: please refer to pinctrl-bindings.txt - fck_parent : Should contain a valid clock name which will be used as parent for the McASP fck +- auxclk-fs-ratio: When McASP is bus master indicates the ratio between AUCLK + and FS rate if applicable: + AUCLK rate = auxclk-fs-ratio * FS rate Optional GPIO support: If any McASP pin need to be used as GPIO then the McASP node must have: diff --git a/Documentation/devicetree/bindings/sound/everest,es8316.txt b/Documentation/devicetree/bindings/sound/everest,es8316.txt new file mode 100644 index 000000000000..1bf03c5f2af4 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/everest,es8316.txt @@ -0,0 +1,23 @@ +Everest ES8316 audio CODEC + +This device supports both I2C and SPI. + +Required properties: + + - compatible : should be "everest,es8316" + - reg : the I2C address of the device for I2C + +Optional properties: + + - clocks : a list of phandle, should contain entries for clock-names + - clock-names : should include as follows: + "mclk" : master clock (MCLK) of the device + +Example: + +es8316: codec@11 { + compatible = "everest,es8316"; + reg = <0x11>; + clocks = <&clks 10>; + clock-names = "mclk"; +}; diff --git a/Documentation/devicetree/bindings/sound/fsl,esai.txt b/Documentation/devicetree/bindings/sound/fsl,esai.txt index 5b9914367610..0e6e2166f76c 100644 --- a/Documentation/devicetree/bindings/sound/fsl,esai.txt +++ b/Documentation/devicetree/bindings/sound/fsl,esai.txt @@ -7,8 +7,11 @@ other DSPs. It has up to six transmitters and four receivers. Required properties: - - compatible : Compatible list, must contain "fsl,imx35-esai" or - "fsl,vf610-esai" + - compatible : Compatible list, should contain one of the following + compatibles: + "fsl,imx35-esai", + "fsl,vf610-esai", + "fsl,imx6ull-esai", - reg : Offset and length of the register set for the device. diff --git a/Documentation/devicetree/bindings/sound/fsl-sai.txt b/Documentation/devicetree/bindings/sound/fsl-sai.txt index 2e726b983845..0dc83cc4a236 100644 --- a/Documentation/devicetree/bindings/sound/fsl-sai.txt +++ b/Documentation/devicetree/bindings/sound/fsl-sai.txt @@ -8,7 +8,9 @@ codec/DSP interfaces. Required properties: - compatible : Compatible list, contains "fsl,vf610-sai", - "fsl,imx6sx-sai" or "fsl,imx6ul-sai" + "fsl,imx6sx-sai", "fsl,imx6ul-sai", + "fsl,imx7ulp-sai", "fsl,imx8mq-sai" or + "fsl,imx8qm-sai". - reg : Offset and length of the register set for the device. diff --git a/Documentation/devicetree/bindings/sound/madera.txt b/Documentation/devicetree/bindings/sound/madera.txt new file mode 100644 index 000000000000..5e669ce552f4 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/madera.txt @@ -0,0 +1,67 @@ +Cirrus Logic Madera class audio codecs + +This describes audio configuration bindings for these codecs. + +See also the core bindings for the parent MFD driver: +See Documentation/devicetree/bindings/mfd/madera.txt + +and defines for values used in these bindings: +include/dt-bindings/sound/madera.h + +These properties are all contained in the parent MFD node. + +Optional properties: + - cirrus,dmic-ref : Indicates how the MICBIAS pins have been externally + connected to DMICs on each input, one cell per input. + <IN1 IN2 IN3 ...> + A value of 0 indicates MICVDD and is the default, other values depend on the + codec: + For CS47L35 one of the CS47L35_DMIC_REF_xxx values + For all other codecs one of the MADERA_DMIC_REF_xxx values + Also see the datasheet for a description of the INn_DMIC_SUP field. + + - cirrus,inmode : A list of input mode settings for each input. A maximum of + 16 cells, with four cells per input in the order INnAL, INnAR INnBL INnBR. + For non-muxed inputs the first two cells for that input set the mode for + the left and right channel and the second two cells must be 0. + For muxed inputs the first two cells for that input set the mode of the + left and right A inputs and the second two cells set the mode of the left + and right B inputs. + Valid mode values are one of the MADERA_INMODE_xxx. If the array is shorter + than the number of inputs the unspecified inputs default to + MADERA_INMODE_DIFF. + + - cirrus,out-mono : Mono bit for each output, maximum of six cells if the + array is shorter outputs will be set to stereo. + + - cirrus,max-channels-clocked : Maximum number of channels that I2S clocks + will be generated for. Useful when clock master for systems where the I2S + bus has multiple data lines. + One cell for each AIF, use a value of zero for AIFs that should be handled + normally. + + - cirrus,pdm-fmt : PDM speaker data format, must contain 2 cells + (OUT5 and OUT6). See the PDM_SPKn_FMT field in the datasheet for a + description of this value. + The second cell is ignored for codecs that do not have OUT6. + + - cirrus,pdm-mute : PDM mute format, must contain 2 cells + (OUT5 and OUT6). See the PDM_SPKn_CTRL_1 register in the datasheet for a + description of this value. + The second cell is ignored for codecs that do not have OUT6. + +Example: + +cs47l35@0 { + compatible = "cirrus,cs47l35"; + + cirrus,dmic-ref = <0 0 CS47L35_DMIC_REF_MICBIAS1B 0>; + cirrus,inmode = < + MADERA_INMODE_DMIC MADERA_INMODE_DMIC /* IN1A digital */ + MADERA_INMODE_SE MADERA_INMODE_SE /* IN1B single-ended */ + MADERA_INMODE_DIFF MADERA_INMODE_DIFF /* IN2 differential */ + 0 0 /* not used on this codec */ + >; + cirrus,out-mono = <0 0 0 0 0 0>; + cirrus,max-channels-clocked = <2 0 0>; +}; diff --git a/Documentation/devicetree/bindings/sound/max98357a.txt b/Documentation/devicetree/bindings/sound/max98357a.txt index 28645a2ff885..4bce14ce806f 100644 --- a/Documentation/devicetree/bindings/sound/max98357a.txt +++ b/Documentation/devicetree/bindings/sound/max98357a.txt @@ -9,6 +9,10 @@ Optional properties: - sdmode-gpios : GPIO specifier for the chip's SD_MODE pin. If this option is not specified then driver does not manage the pin state (e.g. chip is always on). +- sdmode-delay : specify delay time for SD_MODE pin. + If this option is specified, which means it's required i2s clocks + ready before SD_MODE is unmuted in order to avoid the speaker pop noise. + It's observed that 5ms is sufficient. Example: diff --git a/Documentation/devicetree/bindings/sound/rt1011.txt b/Documentation/devicetree/bindings/sound/rt1011.txt new file mode 100644 index 000000000000..35a23e60d679 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt1011.txt @@ -0,0 +1,32 @@ +RT1011 Mono Class D Audio Amplifier + +This device supports I2C only. + +Required properties: + +- compatible : "realtek,rt1011". + +- reg : The I2C address of the device. This I2C address decide by + two input pins (ASEL1 and ASEL2). + ------------------------------------- + | ASEL2 | ASEL1 | Address | + ------------------------------------- + | 0 | 0 | 0x38 | + ------------------------------------- + | 0 | 1 | 0x39 | + ------------------------------------- + | 1 | 0 | 0x3a | + ------------------------------------- + | 1 | 1 | 0x3b | + ------------------------------------- + +Pins on the device (for linking into audio routes) for RT1011: + + * SPO + +Example: + +rt1011: codec@38 { + compatible = "realtek,rt1011"; + reg = <0x38>; +}; diff --git a/Documentation/devicetree/bindings/sound/rt1308.txt b/Documentation/devicetree/bindings/sound/rt1308.txt new file mode 100755 index 000000000000..2d46084afce4 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt1308.txt @@ -0,0 +1,17 @@ +RT1308 audio Amplifier + +This device supports I2C only. + +Required properties: + +- compatible : "realtek,rt1308". + +- reg : The I2C address of the device. + + +Example: + +rt1308: rt1308@10 { + compatible = "realtek,rt1308"; + reg = <0x10>; +}; diff --git a/Documentation/devicetree/bindings/sound/st,stm32-i2s.txt b/Documentation/devicetree/bindings/sound/st,stm32-i2s.txt index 58c341300552..cbf24bcd1b8d 100644 --- a/Documentation/devicetree/bindings/sound/st,stm32-i2s.txt +++ b/Documentation/devicetree/bindings/sound/st,stm32-i2s.txt @@ -18,7 +18,7 @@ Required properties: See Documentation/devicetree/bindings/dma/stm32-dma.txt. - dma-names: Identifier for each DMA request line. Must be "tx" and "rx". - pinctrl-names: should contain only value "default" - - pinctrl-0: see Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt + - pinctrl-0: see Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml Optional properties: - resets: Reference to a reset controller asserting the reset controller diff --git a/Documentation/devicetree/bindings/sound/st,stm32-sai.txt b/Documentation/devicetree/bindings/sound/st,stm32-sai.txt index 3f4467ff0aa2..944743dd9212 100644 --- a/Documentation/devicetree/bindings/sound/st,stm32-sai.txt +++ b/Documentation/devicetree/bindings/sound/st,stm32-sai.txt @@ -41,7 +41,7 @@ SAI subnodes required properties: "tx": if sai sub-block is configured as playback DAI "rx": if sai sub-block is configured as capture DAI - pinctrl-names: should contain only value "default" - - pinctrl-0: see Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt + - pinctrl-0: see Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml SAI subnodes Optional properties: - st,sync: specify synchronization mode. diff --git a/Documentation/devicetree/bindings/sound/sun4i-i2s.txt b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt deleted file mode 100644 index 61e71c1729e0..000000000000 --- a/Documentation/devicetree/bindings/sound/sun4i-i2s.txt +++ /dev/null @@ -1,45 +0,0 @@ -* Allwinner A10 I2S controller - -The I2S bus (Inter-IC sound bus) is a serial link for digital -audio data transfer between devices in the system. - -Required properties: - -- compatible: should be one of the following: - - "allwinner,sun4i-a10-i2s" - - "allwinner,sun6i-a31-i2s" - - "allwinner,sun8i-a83t-i2s" - - "allwinner,sun8i-h3-i2s" - - "allwinner,sun50i-a64-codec-i2s" -- reg: physical base address of the controller and length of memory mapped - region. -- interrupts: should contain the I2S interrupt. -- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, - Documentation/devicetree/bindings/dma/dma.txt -- dma-names: should include "tx" and "rx". -- clocks: a list of phandle + clock-specifer pairs, one for each entry in clock-names. -- clock-names: should contain the following: - - "apb" : clock for the I2S bus interface - - "mod" : module clock for the I2S controller -- #sound-dai-cells : Must be equal to 0 - -Required properties for the following compatibles: - - "allwinner,sun6i-a31-i2s" - - "allwinner,sun8i-a83t-i2s" - - "allwinner,sun8i-h3-i2s" - - "allwinner,sun50i-a64-codec-i2s" -- resets: phandle to the reset line for this codec - -Example: - -i2s0: i2s@1c22400 { - #sound-dai-cells = <0>; - compatible = "allwinner,sun4i-a10-i2s"; - reg = <0x01c22400 0x400>; - interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&apb0_gates 3>, <&i2s0_clk>; - clock-names = "apb", "mod"; - dmas = <&dma SUN4I_DMA_NORMAL 3>, - <&dma SUN4I_DMA_NORMAL 3>; - dma-names = "rx", "tx"; -}; diff --git a/Documentation/devicetree/bindings/sound/sun50i-codec-analog.txt b/Documentation/devicetree/bindings/sound/sun50i-codec-analog.txt deleted file mode 100644 index 056a098495cc..000000000000 --- a/Documentation/devicetree/bindings/sound/sun50i-codec-analog.txt +++ /dev/null @@ -1,14 +0,0 @@ -* Allwinner A64 Codec Analog Controls - -Required properties: -- compatible: must be one of the following compatibles: - - "allwinner,sun50i-a64-codec-analog" -- reg: must contain the registers location and length -- cpvdd-supply: Regulator supply for the headphone amplifier - -Example: - codec_analog: codec-analog@1f015c0 { - compatible = "allwinner,sun50i-a64-codec-analog"; - reg = <0x01f015c0 0x4>; - cpvdd-supply = <®_eldo1>; - }; diff --git a/Documentation/devicetree/bindings/sound/sun8i-a33-codec.txt b/Documentation/devicetree/bindings/sound/sun8i-a33-codec.txt deleted file mode 100644 index 2ca3d138528e..000000000000 --- a/Documentation/devicetree/bindings/sound/sun8i-a33-codec.txt +++ /dev/null @@ -1,63 +0,0 @@ -Allwinner SUN8I audio codec ------------------------------------- - -On Sun8i-A33 SoCs, the audio is separated in different parts: - - A DAI driver. It uses the "sun4i-i2s" driver which is - documented here: - Documentation/devicetree/bindings/sound/sun4i-i2s.txt - - An analog part of the codec which is handled as PRCM registers. - See Documentation/devicetree/bindings/sound/sun8i-codec-analog.txt - - An digital part of the codec which is documented in this current - binding documentation. - - And finally, an audio card which links all the above components. - The simple-audio card will be used. - See Documentation/devicetree/bindings/sound/simple-card.txt - -This bindings documentation exposes Sun8i codec (digital part). - -Required properties: -- compatible: must be "allwinner,sun8i-a33-codec" -- reg: must contain the registers location and length -- interrupts: must contain the codec interrupt -- clocks: a list of phandle + clock-specifer pairs, one for each entry - in clock-names. -- clock-names: should contain followings: - - "bus": the parent APB clock for this controller - - "mod": the parent module clock - -Here is an example to add a sound card and the codec binding on sun8i SoCs that -are similar to A33 using simple-card: - - sound { - compatible = "simple-audio-card"; - simple-audio-card,name = "sun8i-a33-audio"; - simple-audio-card,format = "i2s"; - simple-audio-card,frame-master = <&link_codec>; - simple-audio-card,bitclock-master = <&link_codec>; - simple-audio-card,mclk-fs = <512>; - simple-audio-card,aux-devs = <&codec_analog>; - simple-audio-card,routing = - "Left DAC", "Digital Left DAC", - "Right DAC", "Digital Right DAC"; - - simple-audio-card,cpu { - sound-dai = <&dai>; - }; - - link_codec: simple-audio-card,codec { - sound-dai = <&codec>; - }; - - soc@1c00000 { - [...] - - audio-codec@1c22e00 { - #sound-dai-cells = <0>; - compatible = "allwinner,sun8i-a33-codec"; - reg = <0x01c22e00 0x400>; - interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>; - clock-names = "bus", "mod"; - }; - }; - diff --git a/Documentation/devicetree/bindings/sound/sunxi,sun4i-spdif.txt b/Documentation/devicetree/bindings/sound/sunxi,sun4i-spdif.txt deleted file mode 100644 index 0c64a209c2e9..000000000000 --- a/Documentation/devicetree/bindings/sound/sunxi,sun4i-spdif.txt +++ /dev/null @@ -1,42 +0,0 @@ -Allwinner Sony/Philips Digital Interface Format (S/PDIF) Controller - -The Allwinner S/PDIF audio block is a transceiver that allows the -processor to receive and transmit digital audio via an coaxial cable or -a fibre cable. -For now only playback is supported. - -Required properties: - - - compatible : should be one of the following: - - "allwinner,sun4i-a10-spdif": for the Allwinner A10 SoC - - "allwinner,sun6i-a31-spdif": for the Allwinner A31 SoC - - "allwinner,sun8i-h3-spdif": for the Allwinner H3 SoC - - - reg : Offset and length of the register set for the device. - - - interrupts : Contains the spdif interrupt. - - - dmas : Generic dma devicetree binding as described in - Documentation/devicetree/bindings/dma/dma.txt. - - - dma-names : Two dmas have to be defined, "tx" and "rx". - - - clocks : Contains an entry for each entry in clock-names. - - - clock-names : Includes the following entries: - "apb" clock for the spdif bus. - "spdif" clock for spdif controller. - - - resets : reset specifier for the ahb reset (A31 and newer only) - -Example: - -spdif: spdif@1c21000 { - compatible = "allwinner,sun4i-a10-spdif"; - reg = <0x01c21000 0x40>; - interrupts = <13>; - clocks = <&apb0_gates 1>, <&spdif_clk>; - clock-names = "apb", "spdif"; - dmas = <&dma 0 2>, <&dma 0 2>; - dma-names = "rx", "tx"; -}; diff --git a/Documentation/devicetree/bindings/sound/uda1334.txt b/Documentation/devicetree/bindings/sound/uda1334.txt new file mode 100644 index 000000000000..f64071b25e8d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/uda1334.txt @@ -0,0 +1,17 @@ +UDA1334 audio CODEC + +This device uses simple GPIO pins for controlling codec settings. + +Required properties: + + - compatible : "nxp,uda1334" + - nxp,mute-gpios: a GPIO spec for the MUTE pin. + - nxp,deemph-gpios: a GPIO spec for the De-emphasis pin + +Example: + +uda1334: audio-codec { + compatible = "nxp,uda1334"; + nxp,mute-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; + nxp,deemph-gpios = <&gpio3 3 GPIO_ACTIVE_LOW>; +}; diff --git a/Documentation/devicetree/bindings/soundwire/soundwire-controller.yaml b/Documentation/devicetree/bindings/soundwire/soundwire-controller.yaml new file mode 100644 index 000000000000..1b43993bccdb --- /dev/null +++ b/Documentation/devicetree/bindings/soundwire/soundwire-controller.yaml @@ -0,0 +1,82 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/soundwire/soundwire-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SoundWire Controller Generic Binding + +maintainers: + - Srinivas Kandagatla <srinivas.kandagatla@linaro.org> + - Vinod Koul <vkoul@kernel.org> + +description: | + SoundWire busses can be described with a node for the SoundWire controller + device and a set of child nodes for each SoundWire slave on the bus. + +properties: + $nodename: + pattern: "^soundwire(@.*)?$" + + "#address-cells": + const: 2 + + "#size-cells": + const: 0 + +patternProperties: + "^.*@[0-9a-f],[0-9a-f]$": + type: object + + properties: + compatible: + pattern: "^sdw[0-9a-f]{1}[0-9a-f]{4}[0-9a-f]{4}[0-9a-f]{2}$" + description: Is the textual representation of SoundWire Enumeration + address. compatible string should contain SoundWire Version ID, + Manufacturer ID, Part ID and Class ID in order and shall be in + lower-case hexadecimal with leading zeroes. + Valid sizes of these fields are + Version ID is 1 nibble, number '0x1' represents SoundWire 1.0 + and '0x2' represents SoundWire 1.1 and so on. + MFD is 4 nibbles + PID is 4 nibbles + CID is 2 nibbles + More Information on detail of encoding of these fields can be + found in MIPI Alliance DisCo & SoundWire 1.0 Specifications. + + reg: + maxItems: 1 + description: + Link ID followed by Instance ID of SoundWire Device Address. + + required: + - compatible + - reg + +required: + - "#address-cells" + - "#size-cells" + +examples: + - | + soundwire@c2d0000 { + #address-cells = <2>; + #size-cells = <0>; + reg = <0x0c2d0000 0x2000>; + + speaker@0,1 { + compatible = "sdw10217201000"; + reg = <0 1>; + powerdown-gpios = <&wcdpinctrl 2 0>; + #thermal-sensor-cells = <0>; + }; + + speaker@0,2 { + compatible = "sdw10217201000"; + reg = <0 2>; + powerdown-gpios = <&wcdpinctrl 2 0>; + #thermal-sensor-cells = <0>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/spi/allwinner,sun4i-a10-spi.yaml b/Documentation/devicetree/bindings/spi/allwinner,sun4i-a10-spi.yaml new file mode 100644 index 000000000000..6d1329c28170 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/allwinner,sun4i-a10-spi.yaml @@ -0,0 +1,87 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/allwinner,sun4i-a10-spi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 SPI Controller Device Tree Bindings + +allOf: + - $ref: "spi-controller.yaml" + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + "#address-cells": true + "#size-cells": true + + compatible: + const: allwinner,sun4i-a10-spi + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Bus Clock + - description: Module Clock + + clock-names: + items: + - const: ahb + - const: mod + + dmas: + items: + - description: RX DMA Channel + - description: TX DMA Channel + + dma-names: + items: + - const: rx + - const: tx + + num-cs: true + +patternProperties: + "^.*@[0-9a-f]+": + type: object + properties: + reg: + items: + minimum: 0 + maximum: 4 + + spi-rx-bus-width: + const: 1 + + spi-tx-bus-width: + const: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + spi1: spi@1c06000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c06000 0x1000>; + interrupts = <11>; + clocks = <&ahb_gates 21>, <&spi1_clk>; + clock-names = "ahb", "mod"; + #address-cells = <1>; + #size-cells = <0>; + }; + +... diff --git a/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml b/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml new file mode 100644 index 000000000000..f36c46d236d7 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml @@ -0,0 +1,107 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/allwinner,sun6i-a31-spi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A31 SPI Controller Device Tree Bindings + +allOf: + - $ref: "spi-controller.yaml" + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + "#address-cells": true + "#size-cells": true + + compatible: + enum: + - allwinner,sun6i-a31-spi + - allwinner,sun8i-h3-spi + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Bus Clock + - description: Module Clock + + clock-names: + items: + - const: ahb + - const: mod + + resets: + maxItems: 1 + + dmas: + items: + - description: RX DMA Channel + - description: TX DMA Channel + + dma-names: + items: + - const: rx + - const: tx + + num-cs: true + +patternProperties: + "^.*@[0-9a-f]+": + type: object + properties: + reg: + items: + minimum: 0 + maximum: 4 + + spi-rx-bus-width: + const: 1 + + spi-tx-bus-width: + const: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + spi1: spi@1c69000 { + compatible = "allwinner,sun6i-a31-spi"; + reg = <0x01c69000 0x1000>; + interrupts = <0 66 4>; + clocks = <&ahb1_gates 21>, <&spi1_clk>; + clock-names = "ahb", "mod"; + resets = <&ahb1_rst 21>; + #address-cells = <1>; + #size-cells = <0>; + }; + + - | + spi0: spi@1c68000 { + compatible = "allwinner,sun8i-h3-spi"; + reg = <0x01c68000 0x1000>; + interrupts = <0 65 4>; + clocks = <&ccu 30>, <&ccu 82>; + clock-names = "ahb", "mod"; + dmas = <&dma 23>, <&dma 23>; + dma-names = "rx", "tx"; + resets = <&ccu 15>; + #address-cells = <1>; + #size-cells = <0>; + }; + +... diff --git a/Documentation/devicetree/bindings/spi/amlogic,meson-gx-spicc.yaml b/Documentation/devicetree/bindings/spi/amlogic,meson-gx-spicc.yaml new file mode 100644 index 000000000000..49b617c98ae7 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/amlogic,meson-gx-spicc.yaml @@ -0,0 +1,67 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 BayLibre, SAS +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/spi/amlogic,meson-gx-spicc.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Amlogic Meson SPI Communication Controller + +maintainers: + - Neil Armstrong <narmstrong@baylibre.com> + +allOf: + - $ref: "spi-controller.yaml#" + +description: | + The Meson SPICC is a generic SPI controller for general purpose Full-Duplex + communications with dedicated 16 words RX/TX PIO FIFOs. + +properties: + compatible: + enum: + - amlogic,meson-gx-spicc # SPICC controller on Amlogic GX and compatible SoCs + - amlogic,meson-axg-spicc # SPICC controller on Amlogic AXG and compatible SoCs + + interrupts: + maxItems: 1 + + reg: + maxItems: 1 + + resets: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + description: input clock for the baud rate generator + items: + - const: core + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +examples: + - | + spi@c1108d80 { + compatible = "amlogic,meson-gx-spicc"; + reg = <0xc1108d80 0x80>; + interrupts = <112>; + clocks = <&clk81>; + clock-names = "core"; + #address-cells = <1>; + #size-cells = <0>; + + ethernet-switch@0 { + compatible = "micrel,ks8995m"; + spi-max-frequency = <1000000>; + reg = <0>; + }; + }; + diff --git a/Documentation/devicetree/bindings/spi/amlogic,meson6-spifc.yaml b/Documentation/devicetree/bindings/spi/amlogic,meson6-spifc.yaml new file mode 100644 index 000000000000..5f33c39d820b --- /dev/null +++ b/Documentation/devicetree/bindings/spi/amlogic,meson6-spifc.yaml @@ -0,0 +1,53 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 BayLibre, SAS +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/spi/amlogic,meson6-spifc.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Amlogic Meson SPI Flash Controller + +maintainers: + - Neil Armstrong <narmstrong@baylibre.com> + +allOf: + - $ref: "spi-controller.yaml#" + +description: | + The Meson SPIFC is a controller optimized for communication with SPI + NOR memories, without DMA support and a 64-byte unified transmit / + receive buffer. + +properties: + compatible: + enum: + - amlogic,meson6-spifc # SPI Flash Controller on Meson6 and compatible SoCs + - amlogic,meson-gxbb-spifc # SPI Flash Controller on GXBB and compatible SoCs + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + +required: + - compatible + - reg + - clocks + +examples: + - | + spi@c1108c80 { + compatible = "amlogic,meson6-spifc"; + reg = <0xc1108c80 0x80>; + clocks = <&clk81>; + #address-cells = <1>; + #size-cells = <0>; + + flash: flash@0 { + compatible = "spansion,m25p80", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <40000000>; + }; + }; + diff --git a/Documentation/devicetree/bindings/spi/nuvoton,npcm-fiu.txt b/Documentation/devicetree/bindings/spi/nuvoton,npcm-fiu.txt new file mode 100644 index 000000000000..a388005842ad --- /dev/null +++ b/Documentation/devicetree/bindings/spi/nuvoton,npcm-fiu.txt @@ -0,0 +1,47 @@ +* Nuvoton FLASH Interface Unit (FIU) SPI Controller + +NPCM FIU supports single, dual and quad communication interface. + +The NPCM7XX supports three FIU modules, +FIU0 and FIUx supports two chip selects, +FIU3 support four chip select. + +Required properties: + - compatible : "nuvoton,npcm750-fiu" for the NPCM7XX BMC + - #address-cells : should be 1. + - #size-cells : should be 0. + - reg : the first contains the register location and length, + the second contains the memory mapping address and length + - reg-names: Should contain the reg names "control" and "memory" + - clocks : phandle of FIU reference clock. + +Required properties in case the pins can be muxed: + - pinctrl-names : a pinctrl state named "default" must be defined. + - pinctrl-0 : phandle referencing pin configuration of the device. + +Optional property: + - nuvoton,spix-mode: enable spix-mode for an expansion bus to an ASIC or CPLD. + +Aliases: +- All the FIU controller nodes should be represented in the aliases node using + the following format 'fiu{n}' where n is a unique number for the alias. + In the NPCM7XX BMC: + fiu0 represent fiu 0 controller + fiu1 represent fiu 3 controller + fiu2 represent fiu x controller + +Example: +fiu3: spi@c00000000 { + compatible = "nuvoton,npcm750-fiu"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xfb000000 0x1000>, <0x80000000 0x10000000>; + reg-names = "control", "memory"; + clocks = <&clk NPCM7XX_CLK_AHB>; + pinctrl-names = "default"; + pinctrl-0 = <&spi3_pins>; + spi-nor@0 { + ... + }; +}; + diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt index 1f6e86f787ef..e07783505498 100644 --- a/Documentation/devicetree/bindings/spi/spi-bus.txt +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -1,111 +1 @@ -SPI (Serial Peripheral Interface) busses - -SPI busses can be described with a node for the SPI controller device -and a set of child nodes for each SPI slave on the bus. The system's SPI -controller may be described for use in SPI master mode or in SPI slave mode, -but not for both at the same time. - -The SPI controller node requires the following properties: -- compatible - Name of SPI bus controller following generic names - recommended practice. - -In master mode, the SPI controller node requires the following additional -properties: -- #address-cells - number of cells required to define a chip select - address on the SPI bus. -- #size-cells - should be zero. - -In slave mode, the SPI controller node requires one additional property: -- spi-slave - Empty property. - -No other properties are required in the SPI bus node. It is assumed -that a driver for an SPI bus device will understand that it is an SPI bus. -However, the binding does not attempt to define the specific method for -assigning chip select numbers. Since SPI chip select configuration is -flexible and non-standardized, it is left out of this binding with the -assumption that board specific platform code will be used to manage -chip selects. Individual drivers can define additional properties to -support describing the chip select layout. - -Optional properties (master mode only): -- cs-gpios - gpios chip select. -- num-cs - total number of chipselects. - -If cs-gpios is used the number of chip selects will be increased automatically -with max(cs-gpios > hw cs). - -So if for example the controller has 2 CS lines, and the cs-gpios -property looks like this: - -cs-gpios = <&gpio1 0 0>, <0>, <&gpio1 1 0>, <&gpio1 2 0>; - -Then it should be configured so that num_chipselect = 4 with the -following mapping: - -cs0 : &gpio1 0 0 -cs1 : native -cs2 : &gpio1 1 0 -cs3 : &gpio1 2 0 - - -SPI slave nodes must be children of the SPI controller node. - -In master mode, one or more slave nodes (up to the number of chip selects) can -be present. Required properties are: -- compatible - Name of SPI device following generic names recommended - practice. -- reg - Chip select address of device. -- spi-max-frequency - Maximum SPI clocking speed of device in Hz. - -In slave mode, the (single) slave node is optional. -If present, it must be called "slave". Required properties are: -- compatible - Name of SPI device following generic names recommended - practice. - -All slave nodes can contain the following optional properties: -- spi-cpol - Empty property indicating device requires inverse clock - polarity (CPOL) mode. -- spi-cpha - Empty property indicating device requires shifted clock - phase (CPHA) mode. -- spi-cs-high - Empty property indicating device requires chip select - active high. -- spi-3wire - Empty property indicating device requires 3-wire mode. -- spi-lsb-first - Empty property indicating device requires LSB first mode. -- spi-tx-bus-width - The bus width (number of data wires) that is used for MOSI. - Defaults to 1 if not present. -- spi-rx-bus-width - The bus width (number of data wires) that is used for MISO. - Defaults to 1 if not present. -- spi-rx-delay-us - Microsecond delay after a read transfer. -- spi-tx-delay-us - Microsecond delay after a write transfer. - -Some SPI controllers and devices support Dual and Quad SPI transfer mode. -It allows data in the SPI system to be transferred using 2 wires (DUAL) or 4 -wires (QUAD). -Now the value that spi-tx-bus-width and spi-rx-bus-width can receive is -only 1 (SINGLE), 2 (DUAL) and 4 (QUAD). -Dual/Quad mode is not allowed when 3-wire mode is used. - -If a gpio chipselect is used for the SPI slave the gpio number will be passed -via the SPI master node cs-gpios property. - -SPI example for an MPC5200 SPI bus: - spi@f00 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; - reg = <0xf00 0x20>; - interrupts = <2 13 0 2 14 0>; - interrupt-parent = <&mpc5200_pic>; - - ethernet-switch@0 { - compatible = "micrel,ks8995m"; - spi-max-frequency = <1000000>; - reg = <0>; - }; - - codec@1 { - compatible = "ti,tlv320aic26"; - spi-max-frequency = <100000>; - reg = <1>; - }; - }; +This file has moved to spi-controller.yaml. diff --git a/Documentation/devicetree/bindings/spi/spi-controller.yaml b/Documentation/devicetree/bindings/spi/spi-controller.yaml new file mode 100644 index 000000000000..732339275848 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-controller.yaml @@ -0,0 +1,160 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/spi-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SPI Controller Generic Binding + +maintainers: + - Mark Brown <broonie@kernel.org> + +description: | + SPI busses can be described with a node for the SPI controller device + and a set of child nodes for each SPI slave on the bus. The system SPI + controller may be described for use in SPI master mode or in SPI slave mode, + but not for both at the same time. + +properties: + $nodename: + pattern: "^spi(@.*|-[0-9a-f])*$" + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + cs-gpios: + description: | + GPIOs used as chip selects. + If that property is used, the number of chip selects will be + increased automatically with max(cs-gpios, hardware chip selects). + + So if, for example, the controller has 4 CS lines, and the + cs-gpios looks like this + cs-gpios = <&gpio1 0 0>, <0>, <&gpio1 1 0>, <&gpio1 2 0>; + + Then it should be configured so that num_chipselect = 4, with + the following mapping + cs0 : &gpio1 0 0 + cs1 : native + cs2 : &gpio1 1 0 + cs3 : &gpio1 2 0 + + num-cs: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Total number of chip selects. + + spi-slave: + $ref: /schemas/types.yaml#/definitions/flag + description: + The SPI controller acts as a slave, instead of a master. + +patternProperties: + "^slave$": + type: object + + properties: + compatible: + description: + Compatible of the SPI device. + + required: + - compatible + + "^.*@[0-9a-f]+$": + type: object + + properties: + compatible: + description: + Compatible of the SPI device. + + reg: + minimum: 0 + maximum: 256 + description: + Chip select used by the device. + + spi-3wire: + $ref: /schemas/types.yaml#/definitions/flag + description: + The device requires 3-wire mode. + + spi-cpha: + $ref: /schemas/types.yaml#/definitions/flag + description: + The device requires shifted clock phase (CPHA) mode. + + spi-cpol: + $ref: /schemas/types.yaml#/definitions/flag + description: + The device requires inverse clock polarity (CPOL) mode. + + spi-cs-high: + $ref: /schemas/types.yaml#/definitions/flag + description: + The device requires the chip select active high. + + spi-lsb-first: + $ref: /schemas/types.yaml#/definitions/flag + description: + The device requires the LSB first mode. + + spi-max-frequency: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Maximum SPI clocking speed of the device in Hz. + + spi-rx-bus-width: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 1, 2, 4 ] + - default: 1 + description: + Bus width to the SPI bus used for MISO. + + spi-rx-delay-us: + description: + Delay, in microseconds, after a read transfer. + + spi-tx-bus-width: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 1, 2, 4 ] + - default: 1 + description: + Bus width to the SPI bus used for MOSI. + + spi-tx-delay-us: + description: + Delay, in microseconds, after a write transfer. + + required: + - compatible + - reg + +examples: + - | + spi@f00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; + reg = <0xf00 0x20>; + interrupts = <2 13 0 2 14 0>; + interrupt-parent = <&mpc5200_pic>; + + ethernet-switch@0 { + compatible = "micrel,ks8995m"; + spi-max-frequency = <1000000>; + reg = <0>; + }; + + codec@1 { + compatible = "ti,tlv320aic26"; + spi-max-frequency = <100000>; + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt index dcc7eaada511..162e024b95a0 100644 --- a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt @@ -6,6 +6,7 @@ Required properties: or "fsl,ls2080a-dspi" followed by "fsl,ls2085a-dspi" "fsl,ls1012a-dspi" followed by "fsl,ls1021a-v1.0-dspi" + "fsl,ls1088a-dspi" followed by "fsl,ls1021a-v1.0-dspi" - reg : Offset and length of the register set for the device - interrupts : Should contain SPI controller interrupt - clocks: from common clock binding: handle to dspi clock. diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-qspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-qspi.txt index e8f1d627d288..69dc5d57b1ef 100644 --- a/Documentation/devicetree/bindings/spi/spi-fsl-qspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-fsl-qspi.txt @@ -3,9 +3,8 @@ Required properties: - compatible : Should be "fsl,vf610-qspi", "fsl,imx6sx-qspi", "fsl,imx7d-qspi", "fsl,imx6ul-qspi", - "fsl,ls1021a-qspi" + "fsl,ls1021a-qspi", "fsl,ls2080a-qspi" or - "fsl,ls2080a-qspi" followed by "fsl,ls1021a-qspi", "fsl,ls1043a-qspi" followed by "fsl,ls1021a-qspi" - reg : the first contains the register location and length, the second contains the memory mapping address and length @@ -34,7 +33,11 @@ qspi0: quadspi@40044000 { clock-names = "qspi_en", "qspi"; flash0: s25fl128s@0 { - .... + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,s25fl128s", "jedec,spi-nor"; + spi-max-frequency = <50000000>; + reg = <0>; }; }; diff --git a/Documentation/devicetree/bindings/spi/spi-gpio.txt b/Documentation/devicetree/bindings/spi/spi-gpio.txt deleted file mode 100644 index 52db562f17a4..000000000000 --- a/Documentation/devicetree/bindings/spi/spi-gpio.txt +++ /dev/null @@ -1,43 +0,0 @@ -SPI-GPIO devicetree bindings - -This represents a group of 3-n GPIO lines used for bit-banged SPI on dedicated -GPIO lines. - -Required properties: - - - compatible: should be set to "spi-gpio" - - #address-cells: should be set to <0x1> - - ranges - - sck-gpios: GPIO spec for the SCK line to use - - miso-gpios: GPIO spec for the MISO line to use - - mosi-gpios: GPIO spec for the MOSI line to use - - cs-gpios: GPIOs to use for chipselect lines. - Not needed if num-chipselects = <0>. - - num-chipselects: Number of chipselect lines. Should be <0> if a single device - with no chip select is connected. - -Deprecated bindings: - -These legacy GPIO line bindings can alternatively be used to define the -GPIO lines used, they should not be used in new device trees. - - - gpio-sck: GPIO spec for the SCK line to use - - gpio-miso: GPIO spec for the MISO line to use - - gpio-mosi: GPIO spec for the MOSI line to use - -Example: - - spi { - compatible = "spi-gpio"; - #address-cells = <0x1>; - ranges; - - sck-gpios = <&gpio 95 0>; - miso-gpios = <&gpio 98 0>; - mosi-gpios = <&gpio 97 0>; - cs-gpios = <&gpio 125 0>; - num-chipselects = <1>; - - /* clients */ - }; - diff --git a/Documentation/devicetree/bindings/spi/spi-gpio.yaml b/Documentation/devicetree/bindings/spi/spi-gpio.yaml new file mode 100644 index 000000000000..55c4f1705f07 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-gpio.yaml @@ -0,0 +1,72 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/spi-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SPI-GPIO devicetree bindings + +maintainers: + - Rob Herring <robh@kernel.org> + +description: + This represents a group of 3-n GPIO lines used for bit-banged SPI on + dedicated GPIO lines. + +allOf: + - $ref: "/schemas/spi/spi-controller.yaml#" + +properties: + compatible: + const: spi-gpio + + sck-gpios: + description: GPIO spec for the SCK line to use + maxItems: 1 + + miso-gpios: + description: GPIO spec for the MISO line to use + maxItems: 1 + + mosi-gpios: + description: GPIO spec for the MOSI line to use + maxItems: 1 + + cs-gpios: + description: GPIOs to use for chipselect lines. + Not needed if num-chipselects = <0>. + minItems: 1 + maxItems: 1024 + + num-chipselects: + description: Number of chipselect lines. Should be <0> if a single device + with no chip select is connected. + $ref: "/schemas/types.yaml#/definitions/uint32" + + # Deprecated properties + gpio-sck: false + gpio-miso: false + gpio-mosi: false + +required: + - compatible + - num-chipselects + - sck-gpios + +examples: + - | + spi { + compatible = "spi-gpio"; + #address-cells = <0x1>; + #size-cells = <0x0>; + + sck-gpios = <&gpio 95 0>; + miso-gpios = <&gpio 98 0>; + mosi-gpios = <&gpio 97 0>; + cs-gpios = <&gpio 125 0>; + num-chipselects = <1>; + + /* clients */ + }; + +... diff --git a/Documentation/devicetree/bindings/spi/spi-meson.txt b/Documentation/devicetree/bindings/spi/spi-meson.txt deleted file mode 100644 index b7f5e86fed22..000000000000 --- a/Documentation/devicetree/bindings/spi/spi-meson.txt +++ /dev/null @@ -1,55 +0,0 @@ -Amlogic Meson SPI controllers - -* SPIFC (SPI Flash Controller) - -The Meson SPIFC is a controller optimized for communication with SPI -NOR memories, without DMA support and a 64-byte unified transmit / -receive buffer. - -Required properties: - - compatible: should be "amlogic,meson6-spifc" or "amlogic,meson-gxbb-spifc" - - reg: physical base address and length of the controller registers - - clocks: phandle of the input clock for the baud rate generator - - #address-cells: should be 1 - - #size-cells: should be 0 - - spi@c1108c80 { - compatible = "amlogic,meson6-spifc"; - reg = <0xc1108c80 0x80>; - clocks = <&clk81>; - #address-cells = <1>; - #size-cells = <0>; - }; - -* SPICC (SPI Communication Controller) - -The Meson SPICC is generic SPI controller for general purpose Full-Duplex -communications with dedicated 16 words RX/TX PIO FIFOs. - -Required properties: - - compatible: should be: - "amlogic,meson-gx-spicc" on Amlogic GX and compatible SoCs. - "amlogic,meson-axg-spicc" on Amlogic AXG and compatible SoCs - - reg: physical base address and length of the controller registers - - interrupts: The interrupt specifier - - clock-names: Must contain "core" - - clocks: phandle of the input clock for the baud rate generator - - #address-cells: should be 1 - - #size-cells: should be 0 - -Optional properties: - - resets: phandle of the internal reset line - -See ../spi/spi-bus.txt for more details on SPI bus master and slave devices -required and optional properties. - -Example : - spi@c1108d80 { - compatible = "amlogic,meson-gx-spicc"; - reg = <0xc1108d80 0x80>; - interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "core"; - clocks = <&clk81>; - #address-cells = <1>; - #size-cells = <0>; - }; diff --git a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt index c0f6c8ecfa2e..3a8079eb18c8 100644 --- a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt +++ b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt @@ -5,6 +5,7 @@ Required properties: - mediatek,mt2701-spi: for mt2701 platforms - mediatek,mt2712-spi: for mt2712 platforms - mediatek,mt6589-spi: for mt6589 platforms + - mediatek,mt6765-spi: for mt6765 platforms - mediatek,mt7622-spi: for mt7622 platforms - "mediatek,mt7629-spi", "mediatek,mt7622-spi": for mt7629 platforms - mediatek,mt8135-spi: for mt8135 platforms diff --git a/Documentation/devicetree/bindings/spi/spi-pl022.yaml b/Documentation/devicetree/bindings/spi/spi-pl022.yaml new file mode 100644 index 000000000000..dfb697c69341 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-pl022.yaml @@ -0,0 +1,165 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/spi-pl022.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM PL022 SPI controller + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +allOf: + - $ref: "spi-controller.yaml#" + +# We need a select here so we don't match all nodes with 'arm,primecell' +select: + properties: + compatible: + contains: + const: arm,pl022 + required: + - compatible + +properties: + compatible: + items: + - const: arm,pl022 + - const: arm,primecell + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 2 + + clock-names: + items: + - enum: + - SSPCLK + - sspclk + - const: apb_pclk + + pl022,autosuspend-delay: + description: delay in ms following transfer completion before the + runtime power management system suspends the device. A setting of 0 + indicates no delay and the device will be suspended immediately. + $ref: "/schemas/types.yaml#/definitions/uint32" + + pl022,rt: + description: indicates the controller should run the message pump with realtime + priority to minimise the transfer latency on the bus (boolean) + type: boolean + + dmas: + description: + Two or more DMA channel specifiers following the convention outlined + in bindings/dma/dma.txt + minItems: 2 + maxItems: 32 + + dma-names: + description: + There must be at least one channel named "tx" for transmit and named "rx" + for receive. + minItems: 2 + maxItems: 32 + additionalItems: true + items: + - const: rx + - const: tx + +patternProperties: + "^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}@[0-9a-f]+$": + type: object + # SPI slave nodes must be children of the SPI master node and can + # contain the following properties. + properties: + pl022,interface: + description: SPI interface type + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - enum: + - 0 # SPI + - 1 # Texas Instruments Synchronous Serial Frame Format + - 2 # Microwire (Half Duplex) + + pl022,com-mode: + description: Specifies the transfer mode + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - enum: + - 0 # interrupt mode + - 1 # polling mode + - 2 # DMA mode + default: 1 + + pl022,rx-level-trig: + description: Rx FIFO watermark level + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - minimum: 0 + maximum: 4 + + pl022,tx-level-trig: + description: Tx FIFO watermark level + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - minimum: 0 + maximum: 4 + + pl022,ctrl-len: + description: Microwire interface - Control length + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - minimum: 0x03 + maximum: 0x1f + + pl022,wait-state: + description: Microwire interface - Wait state + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - enum: [ 0, 1 ] + + pl022,duplex: + description: Microwire interface - Full/Half duplex + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - enum: [ 0, 1 ] + +required: + - compatible + - reg + - interrupts + +examples: + - | + spi@e0100000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0xe0100000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 31 0x4>; + dmas = <&dma_controller 23 1>, + <&dma_controller 24 0>; + dma-names = "rx", "tx"; + + m25p80@1 { + compatible = "st,m25p80"; + reg = <1>; + spi-max-frequency = <12000000>; + spi-cpol; + spi-cpha; + pl022,interface = <0>; + pl022,com-mode = <0x2>; + pl022,rx-level-trig = <0>; + pl022,tx-level-trig = <0>; + pl022,ctrl-len = <0x11>; + pl022,wait-state = <0>; + pl022,duplex = <0>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/spi/spi-sprd-adi.txt b/Documentation/devicetree/bindings/spi/spi-sprd-adi.txt index 8de589b376ce..2567c829e2dc 100644 --- a/Documentation/devicetree/bindings/spi/spi-sprd-adi.txt +++ b/Documentation/devicetree/bindings/spi/spi-sprd-adi.txt @@ -25,18 +25,23 @@ data by ADI software channels at the same time, or two parallel routine of setti ADI registers will make ADI controller registers chaos to lead incorrect results. Then we need one hardware spinlock to synchronize between the multiple subsystems. +The new version ADI controller supplies multiple master channels for different +subsystem accessing, that means no need to add hardware spinlock to synchronize, +thus change the hardware spinlock support to be optional to keep backward +compatibility. + Required properties: - compatible: Should be "sprd,sc9860-adi". - reg: Offset and length of ADI-SPI controller register space. -- hwlocks: Reference to a phandle of a hwlock provider node. -- hwlock-names: Reference to hwlock name strings defined in the same order - as the hwlocks, should be "adi". - #address-cells: Number of cells required to define a chip select address on the ADI-SPI bus. Should be set to 1. - #size-cells: Size of cells required to define a chip select address size on the ADI-SPI bus. Should be set to 0. Optional properties: +- hwlocks: Reference to a phandle of a hwlock provider node. +- hwlock-names: Reference to hwlock name strings defined in the same order + as the hwlocks, should be "adi". - sprd,hw-channels: This is an array of channel values up to 49 channels. The first value specifies the hardware channel id which is used to transfer data triggered by hardware automatically, and the second diff --git a/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt b/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt index adeeb63e84b9..bfc038b9478d 100644 --- a/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt @@ -19,8 +19,11 @@ Required properties: - reg: chip-Select number (QSPI controller may connect 2 flashes) - spi-max-frequency: max frequency of spi bus -Optional property: +Optional properties: - spi-rx-bus-width: see ./spi-bus.txt for the description +- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, +Documentation/devicetree/bindings/dma/dma.txt. +- dma-names: DMA request names should include "tx" and "rx" if present. Example: diff --git a/Documentation/devicetree/bindings/spi/spi-sun4i.txt b/Documentation/devicetree/bindings/spi/spi-sun4i.txt deleted file mode 100644 index c75d604a8290..000000000000 --- a/Documentation/devicetree/bindings/spi/spi-sun4i.txt +++ /dev/null @@ -1,23 +0,0 @@ -Allwinner A10 SPI controller - -Required properties: -- compatible: Should be "allwinner,sun4-a10-spi". -- reg: Should contain register location and length. -- interrupts: Should contain interrupt. -- clocks: phandle to the clocks feeding the SPI controller. Two are - needed: - - "ahb": the gated AHB parent clock - - "mod": the parent module clock -- clock-names: Must contain the clock names described just above - -Example: - -spi1: spi@1c06000 { - compatible = "allwinner,sun4i-a10-spi"; - reg = <0x01c06000 0x1000>; - interrupts = <11>; - clocks = <&ahb_gates 21>, <&spi1_clk>; - clock-names = "ahb", "mod"; - #address-cells = <1>; - #size-cells = <0>; -}; diff --git a/Documentation/devicetree/bindings/spi/spi-sun6i.txt b/Documentation/devicetree/bindings/spi/spi-sun6i.txt deleted file mode 100644 index 435a8e0731ac..000000000000 --- a/Documentation/devicetree/bindings/spi/spi-sun6i.txt +++ /dev/null @@ -1,44 +0,0 @@ -Allwinner A31/H3 SPI controller - -Required properties: -- compatible: Should be "allwinner,sun6i-a31-spi" or "allwinner,sun8i-h3-spi". -- reg: Should contain register location and length. -- interrupts: Should contain interrupt. -- clocks: phandle to the clocks feeding the SPI controller. Two are - needed: - - "ahb": the gated AHB parent clock - - "mod": the parent module clock -- clock-names: Must contain the clock names described just above -- resets: phandle to the reset controller asserting this device in - reset - -Optional properties: -- dmas: DMA specifiers for rx and tx dma. See the DMA client binding, - Documentation/devicetree/bindings/dma/dma.txt -- dma-names: DMA request names should include "rx" and "tx" if present. - -Example: - -spi1: spi@1c69000 { - compatible = "allwinner,sun6i-a31-spi"; - reg = <0x01c69000 0x1000>; - interrupts = <0 66 4>; - clocks = <&ahb1_gates 21>, <&spi1_clk>; - clock-names = "ahb", "mod"; - resets = <&ahb1_rst 21>; -}; - -spi0: spi@1c68000 { - compatible = "allwinner,sun8i-h3-spi"; - reg = <0x01c68000 0x1000>; - interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>; - clock-names = "ahb", "mod"; - dmas = <&dma 23>, <&dma 23>; - dma-names = "rx", "tx"; - pinctrl-names = "default"; - pinctrl-0 = <&spi0_pins>; - resets = <&ccu RST_BUS_SPI0>; - #address-cells = <1>; - #size-cells = <0>; -}; diff --git a/Documentation/devicetree/bindings/spi/spi-synquacer.txt b/Documentation/devicetree/bindings/spi/spi-synquacer.txt new file mode 100644 index 000000000000..291dfa692d0a --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-synquacer.txt @@ -0,0 +1,27 @@ +* Socionext Synquacer HS-SPI bindings + +Required Properties: +- compatible: should be "socionext,synquacer-spi" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: should contain the "spi_rx", "spi_tx" and "spi_fault" interrupts. +- clocks: core clock iHCLK. Optional rate clock iPCLK (default is iHCLK) +- clock-names: Shall be "iHCLK" and "iPCLK" respectively + +Optional Properties: +- socionext,use-rtm: boolean, if required to use "retimed clock" for RX +- socionext,set-aces: boolean, if same active clock edges field to be set. + +Example: + + spi0: spi@ff110000 { + compatible = "socionext,synquacer-spi"; + reg = <0xff110000 0x1000>; + interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_hsspi>; + clock-names = "iHCLK"; + socionext,use-rtm; + socionext,set-aces; + }; diff --git a/Documentation/devicetree/bindings/spi/spi_pl022.txt b/Documentation/devicetree/bindings/spi/spi_pl022.txt deleted file mode 100644 index 7638b4968ddb..000000000000 --- a/Documentation/devicetree/bindings/spi/spi_pl022.txt +++ /dev/null @@ -1,70 +0,0 @@ -ARM PL022 SPI controller - -Required properties: -- compatible : "arm,pl022", "arm,primecell" -- reg : Offset and length of the register set for the device -- interrupts : Should contain SPI controller interrupt -- num-cs : total number of chipselects - -Optional properties: -- cs-gpios : should specify GPIOs used for chipselects. - The gpios will be referred to as reg = <index> in the SPI child nodes. - If unspecified, a single SPI device without a chip select can be used. -- pl022,autosuspend-delay : delay in ms following transfer completion before - the runtime power management system suspends the - device. A setting of 0 indicates no delay and the - device will be suspended immediately -- pl022,rt : indicates the controller should run the message pump with realtime - priority to minimise the transfer latency on the bus (boolean) -- dmas : Two or more DMA channel specifiers following the convention outlined - in bindings/dma/dma.txt -- dma-names: Names for the dma channels, if present. There must be at - least one channel named "tx" for transmit and named "rx" for - receive. - - -SPI slave nodes must be children of the SPI master node and can -contain the following properties. - -- pl022,interface : interface type: - 0: SPI - 1: Texas Instruments Synchronous Serial Frame Format - 2: Microwire (Half Duplex) -- pl022,com-mode : specifies the transfer mode: - 0: interrupt mode - 1: polling mode (default mode if property not present) - 2: DMA mode -- pl022,rx-level-trig : Rx FIFO watermark level -- pl022,tx-level-trig : Tx FIFO watermark level -- pl022,ctrl-len : Microwire interface: Control length -- pl022,wait-state : Microwire interface: Wait state -- pl022,duplex : Microwire interface: Full/Half duplex - - -Example: - - spi@e0100000 { - compatible = "arm,pl022", "arm,primecell"; - reg = <0xe0100000 0x1000>; - #address-cells = <1>; - #size-cells = <0>; - interrupts = <0 31 0x4>; - dmas = <&dma-controller 23 1>, - <&dma-controller 24 0>; - dma-names = "rx", "tx"; - - m25p80@1 { - compatible = "st,m25p80"; - reg = <1>; - spi-max-frequency = <12000000>; - spi-cpol; - spi-cpha; - pl022,interface = <0>; - pl022,com-mode = <0x2>; - pl022,rx-level-trig = <0>; - pl022,tx-level-trig = <0>; - pl022,ctrl-len = <0x11>; - pl022,wait-state = <0>; - pl022,duplex = <0>; - }; - }; diff --git a/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt index 04cbb90a5d3e..28f2cbaf1702 100644 --- a/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt @@ -23,6 +23,7 @@ Required properties: Optional property: - little-endian : If present, the TMU registers are little endian. If absent, the default is big endian. +- clocks : the clock for clocking the TMU silicon. Example: diff --git a/Documentation/devicetree/bindings/timer/allwinner,sun4i-a10-timer.yaml b/Documentation/devicetree/bindings/timer/allwinner,sun4i-a10-timer.yaml new file mode 100644 index 000000000000..20adc1c8e9cc --- /dev/null +++ b/Documentation/devicetree/bindings/timer/allwinner,sun4i-a10-timer.yaml @@ -0,0 +1,102 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/timer/allwinner,sun4i-a10-timer.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 Timer Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + compatible: + enum: + - allwinner,sun4i-a10-timer + - allwinner,sun8i-a23-timer + - allwinner,sun8i-v3s-timer + - allwinner,suniv-f1c100s-timer + + reg: + maxItems: 1 + + interrupts: + description: + List of timers interrupts + + clocks: + maxItems: 1 + +allOf: + - if: + properties: + compatible: + items: + const: allwinner,sun4i-a10-timer + + then: + properties: + interrupts: + minItems: 6 + maxItems: 6 + + - if: + properties: + compatible: + items: + const: allwinner,sun8i-a23-timer + + then: + properties: + interrupts: + minItems: 2 + maxItems: 2 + + - if: + properties: + compatible: + items: + const: allwinner,sun8i-v3s-timer + + then: + properties: + interrupts: + minItems: 3 + maxItems: 3 + + - if: + properties: + compatible: + items: + const: allwinner,suniv-f1c100s-timer + + then: + properties: + interrupts: + minItems: 3 + maxItems: 3 + +required: + - compatible + - reg + - interrupts + - clocks + +additionalProperties: false + +examples: + - | + timer { + compatible = "allwinner,sun4i-a10-timer"; + reg = <0x01c20c00 0x400>; + interrupts = <22>, + <23>, + <24>, + <25>, + <67>, + <68>; + clocks = <&osc>; + }; + +... diff --git a/Documentation/devicetree/bindings/timer/allwinner,sun4i-timer.txt b/Documentation/devicetree/bindings/timer/allwinner,sun4i-timer.txt deleted file mode 100644 index 3da9d515c03a..000000000000 --- a/Documentation/devicetree/bindings/timer/allwinner,sun4i-timer.txt +++ /dev/null @@ -1,19 +0,0 @@ -Allwinner A1X SoCs Timer Controller - -Required properties: - -- compatible : should be one of the following: - "allwinner,sun4i-a10-timer" - "allwinner,suniv-f1c100s-timer" -- reg : Specifies base physical address and size of the registers. -- interrupts : The interrupt of the first timer -- clocks: phandle to the source clock (usually a 24 MHz fixed clock) - -Example: - -timer { - compatible = "allwinner,sun4i-a10-timer"; - reg = <0x01c20c00 0x400>; - interrupts = <22>; - clocks = <&osc>; -}; diff --git a/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt b/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt deleted file mode 100644 index 2c5c1be78360..000000000000 --- a/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt +++ /dev/null @@ -1,26 +0,0 @@ -Allwinner SoCs High Speed Timer Controller - -Required properties: - -- compatible : should be "allwinner,sun5i-a13-hstimer" or - "allwinner,sun7i-a20-hstimer" -- reg : Specifies base physical address and size of the registers. -- interrupts : The interrupts of these timers (2 for the sun5i IP, 4 for the sun7i - one) -- clocks: phandle to the source clock (usually the AHB clock) - -Optional properties: -- resets: phandle to a reset controller asserting the timer - -Example: - -timer@1c60000 { - compatible = "allwinner,sun7i-a20-hstimer"; - reg = <0x01c60000 0x1000>; - interrupts = <0 51 1>, - <0 52 1>, - <0 53 1>, - <0 54 1>; - clocks = <&ahb1_gates 19>; - resets = <&ahb1rst 19>; -}; diff --git a/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.yaml b/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.yaml new file mode 100644 index 000000000000..dfa0c41fd261 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.yaml @@ -0,0 +1,79 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/timer/allwinner,sun5i-a13-hstimer.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A13 High-Speed Timer Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + compatible: + oneOf: + - const: allwinner,sun5i-a13-hstimer + - const: allwinner,sun7i-a20-hstimer + - items: + - const: allwinner,sun6i-a31-hstimer + - const: allwinner,sun7i-a20-hstimer + + reg: + maxItems: 1 + + interrupts: + minItems: 2 + maxItems: 4 + items: + - description: Timer 0 Interrupt + - description: Timer 1 Interrupt + - description: Timer 2 Interrupt + - description: Timer 3 Interrupt + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + +if: + properties: + compatible: + items: + const: allwinner,sun5i-a13-hstimer + +then: + properties: + interrupts: + minItems: 2 + maxItems: 2 + +else: + properties: + interrupts: + minItems: 4 + maxItems: 4 + +additionalProperties: false + +examples: + - | + timer@1c60000 { + compatible = "allwinner,sun7i-a20-hstimer"; + reg = <0x01c60000 0x1000>; + interrupts = <0 51 1>, + <0 52 1>, + <0 53 1>, + <0 54 1>; + clocks = <&ahb1_gates 19>; + resets = <&ahb1rst 19>; + }; + +... diff --git a/Documentation/devicetree/bindings/timer/ingenic,tcu.txt b/Documentation/devicetree/bindings/timer/ingenic,tcu.txt new file mode 100644 index 000000000000..5a4b9ddd9470 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/ingenic,tcu.txt @@ -0,0 +1,137 @@ +Ingenic JZ47xx SoCs Timer/Counter Unit devicetree bindings +========================================================== + +For a description of the TCU hardware and drivers, have a look at +Documentation/mips/ingenic-tcu.txt. + +Required properties: + +- compatible: Must be one of: + * ingenic,jz4740-tcu + * ingenic,jz4725b-tcu + * ingenic,jz4770-tcu + followed by "simple-mfd". +- reg: Should be the offset/length value corresponding to the TCU registers +- clocks: List of phandle & clock specifiers for clocks external to the TCU. + The "pclk", "rtc" and "ext" clocks should be provided. The "tcu" clock + should be provided if the SoC has it. +- clock-names: List of name strings for the external clocks. +- #clock-cells: Should be <1>; + Clock consumers specify this argument to identify a clock. The valid values + may be found in <dt-bindings/clock/ingenic,tcu.h>. +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value should be 1. +- interrupts : Specifies the interrupt the controller is connected to. + +Optional properties: + +- ingenic,pwm-channels-mask: Bitmask of TCU channels reserved for PWM use. + Default value is 0xfc. + + +Children nodes +========================================================== + + +PWM node: +--------- + +Required properties: + +- compatible: Must be one of: + * ingenic,jz4740-pwm + * ingenic,jz4725b-pwm +- #pwm-cells: Should be 3. See ../pwm/pwm.txt for a description of the cell + format. +- clocks: List of phandle & clock specifiers for the TCU clocks. +- clock-names: List of name strings for the TCU clocks. + + +Watchdog node: +-------------- + +Required properties: + +- compatible: Must be "ingenic,jz4740-watchdog" +- clocks: phandle to the WDT clock +- clock-names: should be "wdt" + + +OS Timer node: +--------- + +Required properties: + +- compatible: Must be one of: + * ingenic,jz4725b-ost + * ingenic,jz4770-ost +- clocks: phandle to the OST clock +- clock-names: should be "ost" +- interrupts : Specifies the interrupt the OST is connected to. + + +Example +========================================================== + +#include <dt-bindings/clock/jz4770-cgu.h> +#include <dt-bindings/clock/ingenic,tcu.h> + +/ { + tcu: timer@10002000 { + compatible = "ingenic,jz4770-tcu", "simple-mfd"; + reg = <0x10002000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x10002000 0x1000>; + + #clock-cells = <1>; + + clocks = <&cgu JZ4770_CLK_RTC + &cgu JZ4770_CLK_EXT + &cgu JZ4770_CLK_PCLK>; + clock-names = "rtc", "ext", "pclk"; + + interrupt-controller; + #interrupt-cells = <1>; + + interrupt-parent = <&intc>; + interrupts = <27 26 25>; + + watchdog: watchdog@0 { + compatible = "ingenic,jz4740-watchdog"; + reg = <0x0 0xc>; + + clocks = <&tcu TCU_CLK_WDT>; + clock-names = "wdt"; + }; + + pwm: pwm@40 { + compatible = "ingenic,jz4740-pwm"; + reg = <0x40 0x80>; + + #pwm-cells = <3>; + + clocks = <&tcu TCU_CLK_TIMER0 + &tcu TCU_CLK_TIMER1 + &tcu TCU_CLK_TIMER2 + &tcu TCU_CLK_TIMER3 + &tcu TCU_CLK_TIMER4 + &tcu TCU_CLK_TIMER5 + &tcu TCU_CLK_TIMER6 + &tcu TCU_CLK_TIMER7>; + clock-names = "timer0", "timer1", "timer2", "timer3", + "timer4", "timer5", "timer6", "timer7"; + }; + + ost: timer@e0 { + compatible = "ingenic,jz4770-ost"; + reg = <0xe0 0x20>; + + clocks = <&tcu TCU_CLK_OST>; + clock-names = "ost"; + + interrupts = <15>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/timer/intel,ixp4xx-timer.yaml b/Documentation/devicetree/bindings/timer/intel,ixp4xx-timer.yaml index a36a0746c056..2807225db902 100644 --- a/Documentation/devicetree/bindings/timer/intel,ixp4xx-timer.yaml +++ b/Documentation/devicetree/bindings/timer/intel,ixp4xx-timer.yaml @@ -2,7 +2,7 @@ # Copyright 2018 Linaro Ltd. %YAML 1.2 --- -$id: "http://devicetree.org/schemas/timer/intel-ixp4xx-timer.yaml#" +$id: "http://devicetree.org/schemas/timer/intel,ixp4xx-timer.yaml#" $schema: "http://devicetree.org/meta-schemas/core.yaml#" title: Intel IXP4xx XScale Networking Processors Timers diff --git a/Documentation/devicetree/bindings/timer/nxp,sysctr-timer.txt b/Documentation/devicetree/bindings/timer/nxp,sysctr-timer.txt new file mode 100644 index 000000000000..d57659996d62 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/nxp,sysctr-timer.txt @@ -0,0 +1,25 @@ +NXP System Counter Module(sys_ctr) + +The system counter(sys_ctr) is a programmable system counter which provides +a shared time base to Cortex A15, A7, A53, A73, etc. it is intended for use in +applications where the counter is always powered and support multiple, +unrelated clocks. The compare frame inside can be used for timer purpose. + +Required properties: + +- compatible : should be "nxp,sysctr-timer" +- reg : Specifies the base physical address and size of the comapre + frame and the counter control, read & compare. +- interrupts : should be the first compare frames' interrupt +- clocks : Specifies the counter clock. +- clock-names: Specifies the clock's name of this module + +Example: + + system_counter: timer@306a0000 { + compatible = "nxp,sysctr-timer"; + reg = <0x306a0000 0x20000>;/* system-counter-rd & compare */ + clocks = <&clk_8m>; + clock-names = "per"; + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/timer/renesas,cmt.txt b/Documentation/devicetree/bindings/timer/renesas,cmt.txt index c0594450e9ef..a444cfc5852a 100644 --- a/Documentation/devicetree/bindings/timer/renesas,cmt.txt +++ b/Documentation/devicetree/bindings/timer/renesas,cmt.txt @@ -12,16 +12,13 @@ datasheets. Required Properties: - compatible: must contain one or more of the following: - - "renesas,cmt-48-sh73a0" for the sh73A0 48-bit CMT - (CMT1) - - "renesas,cmt-48-r8a7740" for the r8a7740 48-bit CMT - (CMT1) - - "renesas,cmt-48" for all non-second generation 48-bit CMT - (CMT1 on sh73a0 and r8a7740) - This is a fallback for the above renesas,cmt-48-* entries. - - "renesas,r8a73a4-cmt0" for the 32-bit CMT0 device included in r8a73a4. - "renesas,r8a73a4-cmt1" for the 48-bit CMT1 device included in r8a73a4. + - "renesas,r8a7740-cmt0" for the 32-bit CMT0 device included in r8a7740. + - "renesas,r8a7740-cmt1" for the 48-bit CMT1 device included in r8a7740. + - "renesas,r8a7740-cmt2" for the 32-bit CMT2 device included in r8a7740. + - "renesas,r8a7740-cmt3" for the 32-bit CMT3 device included in r8a7740. + - "renesas,r8a7740-cmt4" for the 32-bit CMT4 device included in r8a7740. - "renesas,r8a7743-cmt0" for the 32-bit CMT0 device included in r8a7743. - "renesas,r8a7743-cmt1" for the 48-bit CMT1 device included in r8a7743. - "renesas,r8a7744-cmt0" for the 32-bit CMT0 device included in r8a7744. @@ -31,23 +28,38 @@ Required Properties: - "renesas,r8a77470-cmt0" for the 32-bit CMT0 device included in r8a77470. - "renesas,r8a77470-cmt1" for the 48-bit CMT1 device included in r8a77470. - "renesas,r8a774a1-cmt0" for the 32-bit CMT0 device included in r8a774a1. - - "renesas,r8a774a1-cmt1" for the 48-bit CMT1 device included in r8a774a1. + - "renesas,r8a774a1-cmt1" for the 48-bit CMT devices included in r8a774a1. - "renesas,r8a774c0-cmt0" for the 32-bit CMT0 device included in r8a774c0. - - "renesas,r8a774c0-cmt1" for the 48-bit CMT1 device included in r8a774c0. + - "renesas,r8a774c0-cmt1" for the 48-bit CMT devices included in r8a774c0. - "renesas,r8a7790-cmt0" for the 32-bit CMT0 device included in r8a7790. - "renesas,r8a7790-cmt1" for the 48-bit CMT1 device included in r8a7790. - "renesas,r8a7791-cmt0" for the 32-bit CMT0 device included in r8a7791. - "renesas,r8a7791-cmt1" for the 48-bit CMT1 device included in r8a7791. + - "renesas,r8a7792-cmt0" for the 32-bit CMT0 device included in r8a7792. + - "renesas,r8a7792-cmt1" for the 48-bit CMT1 device included in r8a7792. - "renesas,r8a7793-cmt0" for the 32-bit CMT0 device included in r8a7793. - "renesas,r8a7793-cmt1" for the 48-bit CMT1 device included in r8a7793. - "renesas,r8a7794-cmt0" for the 32-bit CMT0 device included in r8a7794. - "renesas,r8a7794-cmt1" for the 48-bit CMT1 device included in r8a7794. + - "renesas,r8a7795-cmt0" for the 32-bit CMT0 device included in r8a7795. + - "renesas,r8a7795-cmt1" for the 48-bit CMT devices included in r8a7795. - "renesas,r8a7796-cmt0" for the 32-bit CMT0 device included in r8a7796. - - "renesas,r8a7796-cmt1" for the 48-bit CMT1 device included in r8a7796. + - "renesas,r8a7796-cmt1" for the 48-bit CMT devices included in r8a7796. + - "renesas,r8a77965-cmt0" for the 32-bit CMT0 device included in r8a77965. + - "renesas,r8a77965-cmt1" for the 48-bit CMT devices included in r8a77965. - "renesas,r8a77970-cmt0" for the 32-bit CMT0 device included in r8a77970. - - "renesas,r8a77970-cmt1" for the 48-bit CMT1 device included in r8a77970. + - "renesas,r8a77970-cmt1" for the 48-bit CMT devices included in r8a77970. - "renesas,r8a77980-cmt0" for the 32-bit CMT0 device included in r8a77980. - - "renesas,r8a77980-cmt1" for the 48-bit CMT1 device included in r8a77980. + - "renesas,r8a77980-cmt1" for the 48-bit CMT devices included in r8a77980. + - "renesas,r8a77990-cmt0" for the 32-bit CMT0 device included in r8a77990. + - "renesas,r8a77990-cmt1" for the 48-bit CMT devices included in r8a77990. + - "renesas,r8a77995-cmt0" for the 32-bit CMT0 device included in r8a77995. + - "renesas,r8a77995-cmt1" for the 48-bit CMT devices included in r8a77995. + - "renesas,sh73a0-cmt0" for the 32-bit CMT0 device included in sh73a0. + - "renesas,sh73a0-cmt1" for the 48-bit CMT1 device included in sh73a0. + - "renesas,sh73a0-cmt2" for the 32-bit CMT2 device included in sh73a0. + - "renesas,sh73a0-cmt3" for the 32-bit CMT3 device included in sh73a0. + - "renesas,sh73a0-cmt4" for the 32-bit CMT4 device included in sh73a0. - "renesas,rcar-gen2-cmt0" for 32-bit CMT0 devices included in R-Car Gen2 and RZ/G1. @@ -57,7 +69,7 @@ Required Properties: listed above. - "renesas,rcar-gen3-cmt0" for 32-bit CMT0 devices included in R-Car Gen3 and RZ/G2. - - "renesas,rcar-gen3-cmt1" for 48-bit CMT1 devices included in R-Car Gen3 + - "renesas,rcar-gen3-cmt1" for 48-bit CMT devices included in R-Car Gen3 and RZ/G2. These are fallbacks for R-Car Gen3 and RZ/G2 entries listed above. diff --git a/Documentation/devicetree/bindings/trivial-devices.yaml b/Documentation/devicetree/bindings/trivial-devices.yaml index 747fd3f689dc..870ac52d2225 100644 --- a/Documentation/devicetree/bindings/trivial-devices.yaml +++ b/Documentation/devicetree/bindings/trivial-devices.yaml @@ -52,6 +52,10 @@ properties: - at,24c08 # i2c trusted platform module (TPM) - atmel,at97sc3204t + # i2c h/w symmetric crypto module + - atmel,atsha204a + # i2c h/w elliptic curve crypto module + - atmel,atecc508a # CM32181: Ambient Light Sensor - capella,cm32181 # CM3232: Ambient Light Sensor @@ -100,6 +104,8 @@ properties: - infineon,slb9645tt # Infineon TLV493D-A1B6 I2C 3D Magnetic Sensor - infineon,tlv493d-a1b6 + # Inspur Power System power supply unit version 1 + - inspur,ipsps1 # Intersil ISL29028 Ambient Light and Proximity Sensor - isil,isl29028 # Intersil ISL29030 Ambient Light and Proximity Sensor diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt index a74720486ee2..d78ef63935f9 100644 --- a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt +++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt @@ -54,6 +54,8 @@ Optional properties: PHY reset from the UFS controller. - resets : reset node register - reset-names : describe reset node register, the "rst" corresponds to reset the whole UFS IP. +- reset-gpios : A phandle and gpio specifier denoting the GPIO connected + to the RESET pin of the UFS memory device. Note: If above properties are not defined it can be assumed that the supply regulators or clocks are always on. diff --git a/Documentation/devicetree/bindings/usb/cdns-usb3.txt b/Documentation/devicetree/bindings/usb/cdns-usb3.txt new file mode 100644 index 000000000000..b7dc606d37b5 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/cdns-usb3.txt @@ -0,0 +1,45 @@ +Binding for the Cadence USBSS-DRD controller + +Required properties: + - reg: Physical base address and size of the controller's register areas. + Controller has 3 different regions: + - HOST registers area + - DEVICE registers area + - OTG/DRD registers area + - reg-names - register memory area names: + "xhci" - for HOST registers space + "dev" - for DEVICE registers space + "otg" - for OTG/DRD registers space + - compatible: Should contain: "cdns,usb3" + - interrupts: Interrupts used by cdns3 controller: + "host" - interrupt used by XHCI driver. + "peripheral" - interrupt used by device driver + "otg" - interrupt used by DRD/OTG part of driver + +Optional properties: + - maximum-speed : valid arguments are "super-speed", "high-speed" and + "full-speed"; refer to usb/generic.txt + - dr_mode: Should be one of "host", "peripheral" or "otg". + - phys: reference to the USB PHY + - phy-names: from the *Generic PHY* bindings; + Supported names are: + - cdns3,usb2-phy + - cdns3,usb3-phy + + - cdns,on-chip-buff-size : size of memory intended as internal memory for endpoints + buffers expressed in KB + +Example: + usb@f3000000 { + compatible = "cdns,usb3"; + interrupts = <GIC_USB_IRQ 7 IRQ_TYPE_LEVEL_HIGH>, + <GIC_USB_IRQ 7 IRQ_TYPE_LEVEL_HIGH>, + <GIC_USB_IRQ 8 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "host", "peripheral", "otg"; + reg = <0xf3000000 0x10000>, /* memory area for HOST registers */ + <0xf3010000 0x10000>, /* memory area for DEVICE registers */ + <0xf3020000 0x10000>; /* memory area for OTG/DRD registers */ + reg-names = "xhci", "dev", "otg"; + phys = <&usb2_phy>, <&usb3_phy>; + phy-names = "cdns3,usb2-phy", "cnds3,usb3-phy"; + }; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index a254386a91ad..cfc9f40ab641 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -10,6 +10,7 @@ Required properties: "fsl,imx6sx-usb" "fsl,imx6ul-usb" "fsl,imx7d-usb" + "fsl,imx7ulp-usb" "lsi,zevio-usb" "qcom,ci-hdrc" "chipidea,usb2" diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt index 49eac0dc86b0..aafff3a6904d 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.txt +++ b/Documentation/devicetree/bindings/usb/dwc2.txt @@ -42,6 +42,8 @@ Refer to phy/phy-bindings.txt for generic phy consumer properties - g-rx-fifo-size: size of rx fifo size in gadget mode. - g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget mode. - g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode. +- snps,need-phy-for-wake: If present indicates that the phy needs to be left + on for remote wakeup during suspend. - snps,reset-phy-on-wake: If present indicates that we need to reset the PHY when we detect a wakeup. This is due to a hardware errata. @@ -58,4 +60,5 @@ Example: clock-names = "otg"; phys = <&usbphy>; phy-names = "usb2-phy"; + snps,need-phy-for-wake; }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 8e5265e9f658..66780a47ad85 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -64,6 +64,8 @@ Optional properties: - snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy. - snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG, disabling the suspend signal to the PHY. + - snps,dis-u1-entry-quirk: set if link entering into U1 needs to be disabled. + - snps,dis-u2-entry-quirk: set if link entering into U2 needs to be disabled. - snps,dis_rxdet_inp3_quirk: when set core will disable receiver detection in PHY P3 power state. - snps,dis-u2-freeclk-exists-quirk: when set, clear the u2_freeclk_exists diff --git a/Documentation/devicetree/bindings/usb/exynos-usb.txt b/Documentation/devicetree/bindings/usb/exynos-usb.txt index b7111f43fa59..66c394f9e11f 100644 --- a/Documentation/devicetree/bindings/usb/exynos-usb.txt +++ b/Documentation/devicetree/bindings/usb/exynos-usb.txt @@ -12,13 +12,11 @@ Required properties: - interrupts: interrupt number to the cpu. - clocks: from common clock binding: handle to usb clock. - clock-names: from common clock binding: Shall be "usbhost". - - port: if in the SoC there are EHCI phys, they should be listed here. - One phy per port. Each port should have following entries: - - reg: port number on EHCI controller, e.g - On Exynos5250, port 0 is USB2.0 otg phy - port 1 is HSIC phy0 - port 2 is HSIC phy1 - - phys: from the *Generic PHY* bindings; specifying phy used by port. + - phys: from the *Generic PHY* bindings; array specifying phy(s) used + by the root port. + - phy-names: from the *Generic PHY* bindings; array of the names for + each phy for the root ports, must be a subset of the following: + "host", "hsic0", "hsic1". Optional properties: - samsung,vbus-gpio: if present, specifies the GPIO that @@ -35,12 +33,8 @@ Example: clocks = <&clock 285>; clock-names = "usbhost"; - #address-cells = <1>; - #size-cells = <0>; - port@0 { - reg = <0>; - phys = <&usb2phy 1>; - }; + phys = <&usb2phy 1>; + phy-names = "host"; }; OHCI @@ -52,13 +46,11 @@ Required properties: - interrupts: interrupt number to the cpu. - clocks: from common clock binding: handle to usb clock. - clock-names: from common clock binding: Shall be "usbhost". - - port: if in the SoC there are OHCI phys, they should be listed here. - One phy per port. Each port should have following entries: - - reg: port number on OHCI controller, e.g - On Exynos5250, port 0 is USB2.0 otg phy - port 1 is HSIC phy0 - port 2 is HSIC phy1 - - phys: from the *Generic PHY* bindings, specifying phy used by port. + - phys: from the *Generic PHY* bindings; array specifying phy(s) used + by the root port. + - phy-names: from the *Generic PHY* bindings; array of the names for + each phy for the root ports, must be a subset of the following: + "host", "hsic0", "hsic1". Example: usb@12120000 { @@ -69,13 +61,8 @@ Example: clocks = <&clock 285>; clock-names = "usbhost"; - #address-cells = <1>; - #size-cells = <0>; - port@0 { - reg = <0>; - phys = <&usb2phy 1>; - }; - + phys = <&usb2phy 1>; + phy-names = "host"; }; DWC3 diff --git a/Documentation/devicetree/bindings/usb/fcs,fusb302.txt b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt index a5d011d2efc8..ba2e32d500c0 100644 --- a/Documentation/devicetree/bindings/usb/fcs,fusb302.txt +++ b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt @@ -11,13 +11,6 @@ Required sub-node: Documentation/devicetree/bindings/connector/usb-connector.txt -Deprecated properties : -- fcs,max-sink-microvolt : Maximum sink voltage accepted by port controller -- fcs,max-sink-microamp : Maximum sink current accepted by port controller -- fcs,max-sink-microwatt : Maximum sink power accepted by port controller -- fcs,operating-sink-microwatt : Minimum amount of power accepted from a sink - when negotiating - Example: diff --git a/Documentation/devicetree/bindings/usb/generic-ehci.yaml b/Documentation/devicetree/bindings/usb/generic-ehci.yaml index d3b4f6415920..059f6ef1ad4a 100644 --- a/Documentation/devicetree/bindings/usb/generic-ehci.yaml +++ b/Documentation/devicetree/bindings/usb/generic-ehci.yaml @@ -74,7 +74,7 @@ additionalProperties: false examples: - | - ehci@e0000300 { + usb@e0000300 { compatible = "ibm,usb-ehci-440epx", "generic-ehci"; interrupt-parent = <&UIC0>; interrupts = <0x1a 4>; @@ -89,7 +89,6 @@ examples: interrupts = <39>; clocks = <&ahb_gates 1>; phys = <&usbphy 1>; - phy-names = "usb"; }; ... diff --git a/Documentation/devicetree/bindings/usb/generic.txt b/Documentation/devicetree/bindings/usb/generic.txt index 0a74ab8dfdc2..cf5a1ad456e6 100644 --- a/Documentation/devicetree/bindings/usb/generic.txt +++ b/Documentation/devicetree/bindings/usb/generic.txt @@ -30,6 +30,10 @@ Optional properties: optional for OTG device. - adp-disable: tells OTG controllers we want to disable OTG ADP, ADP is optional for OTG device. + - usb-role-switch: boolean, indicates that the device is capable of assigning + the USB data role (USB host or USB device) for a given + USB connector, such as Type-C, Type-B(micro). + see connector/usb-connector.txt. This is an attribute to a USB controller such as: diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt index 266c2d917a28..f3e4acecabe8 100644 --- a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt +++ b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt @@ -30,7 +30,8 @@ Required properties: the following ones are optional: "ref_ck": reference clock used by low power mode etc, "mcu_ck": mcu_bus clock for register access, - "dma_ck": dma_bus clock for data transfer by DMA + "dma_ck": dma_bus clock for data transfer by DMA, + "xhci_ck": controller clock - phys : see usb-hcd.txt in the current directory @@ -100,7 +101,7 @@ Required properties: - clocks : a list of phandle + clock-specifier pairs, one for each entry in clock-names - clock-names : must contain "sys_ck", and the following ones are optional: - "ref_ck", "mcu_ck" and "dma_ck" + "ref_ck", "mcu_ck" and "dma_ck", "xhci_ck" Optional properties: - vbus-supply : reference to the VBUS regulator; diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt b/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt index 3382b5cb471d..b9af7f5ee91d 100644 --- a/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt +++ b/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt @@ -16,7 +16,7 @@ Required properties: entry in clock-names - clock-names : must contain "sys_ck" for clock of controller, the following clocks are optional: - "ref_ck", "mcu_ck" and "dam_ck"; + "ref_ck", "mcu_ck" and "dma_ck"; - phys : see usb-hcd.txt in the current directory - dr_mode : should be one of "host", "peripheral" or "otg", refer to usb/generic.txt @@ -28,8 +28,13 @@ Optional properties: parent's address space - extcon : external connector for vbus and idpin changes detection, needed when supports dual-role mode. + it's considered valid for compatibility reasons, not allowed for + new bindings, and use "usb-role-switch" property instead. - vbus-supply : reference to the VBUS regulator, needed when supports dual-role mode. + it's considered valid for compatibility reasons, not allowed for + new bindings, and put into a usb-connector node. + see connector/usb-connector.txt. - pinctrl-names : a pinctrl state named "default" is optional, and need be defined if auto drd switch is enabled, that means the property dr_mode is set as "otg", and meanwhile the property "mediatek,enable-manual-drd" @@ -39,6 +44,8 @@ Optional properties: - maximum-speed : valid arguments are "super-speed", "high-speed" and "full-speed"; refer to usb/generic.txt + - usb-role-switch : use USB Role Switch to support dual-role switch, but + not extcon; see usb/generic.txt. - enable-manual-drd : supports manual dual-role switch via debugfs; usually used when receptacle is TYPE-A and also wants to support dual-role mode. @@ -61,6 +68,9 @@ The xhci should be added as subnode to mtu3 as shown in the following example if host mode is enabled. The DT binding details of xhci can be found in: Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt +The port would be added as subnode if use "usb-role-switch" property. + see graph.txt + Example: ssusb: usb@11271000 { compatible = "mediatek,mt8173-mtu3"; diff --git a/Documentation/devicetree/bindings/usb/renesas_usb3.txt b/Documentation/devicetree/bindings/usb/renesas,usb3-peri.txt index 35039e720515..35039e720515 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usb3.txt +++ b/Documentation/devicetree/bindings/usb/renesas,usb3-peri.txt diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas,usbhs.txt index b8acc2a994a8..e39255ea6e4f 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt +++ b/Documentation/devicetree/bindings/usb/renesas,usbhs.txt @@ -20,9 +20,11 @@ Required properties: - "renesas,usbhs-r8a77990" for r8a77990 (R-Car E3) compatible device - "renesas,usbhs-r8a77995" for r8a77995 (R-Car D3) compatible device - "renesas,usbhs-r7s72100" for r7s72100 (RZ/A1) compatible device + - "renesas,usbhs-r7s9210" for r7s9210 (RZ/A2) compatible device - "renesas,rcar-gen2-usbhs" for R-Car Gen2 or RZ/G1 compatible devices - "renesas,rcar-gen3-usbhs" for R-Car Gen3 or RZ/G2 compatible devices - "renesas,rza1-usbhs" for RZ/A1 compatible device + - "renesas,rza2-usbhs" for RZ/A2 compatible device When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first followed diff --git a/Documentation/devicetree/bindings/usb/s3c2410-usb.txt b/Documentation/devicetree/bindings/usb/s3c2410-usb.txt index e45b38ce2986..26c85afd0b53 100644 --- a/Documentation/devicetree/bindings/usb/s3c2410-usb.txt +++ b/Documentation/devicetree/bindings/usb/s3c2410-usb.txt @@ -4,7 +4,7 @@ OHCI Required properties: - compatible: should be "samsung,s3c2410-ohci" for USB host controller - - reg: address and lenght of the controller memory mapped region + - reg: address and length of the controller memory mapped region - interrupts: interrupt number for the USB OHCI controller - clocks: Should reference the bus and host clocks - clock-names: Should contain two strings diff --git a/Documentation/devicetree/bindings/usb/usb-conn-gpio.txt b/Documentation/devicetree/bindings/usb/usb-conn-gpio.txt new file mode 100644 index 000000000000..3d05ae56cb0d --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-conn-gpio.txt @@ -0,0 +1,30 @@ +USB GPIO Based Connection Detection + +This is typically used to switch dual role mode from the USB ID pin connected +to an input GPIO, and also used to enable/disable device mode from the USB +Vbus pin connected to an input GPIO. + +Required properties: +- compatible : should include "gpio-usb-b-connector" and "usb-b-connector". +- id-gpios, vbus-gpios : input gpios, either one of them must be present, + and both can be present as well. + see connector/usb-connector.txt + +Optional properties: +- vbus-supply : can be present if needed when supports dual role mode. + see connector/usb-connector.txt + +- Sub-nodes: + - port : can be present. + see graph.txt + +Example: + +&mtu3 { + connector { + compatible = "gpio-usb-b-connector", "usb-b-connector"; + type = "micro"; + id-gpios = <&pio 12 GPIO_ACTIVE_HIGH>; + vbus-supply = <&usb_p0_vbus>; + }; +}; diff --git a/Documentation/devicetree/bindings/usb/usb251xb.txt b/Documentation/devicetree/bindings/usb/usb251xb.txt index bc7945e9dbfe..17915f64b8ee 100644 --- a/Documentation/devicetree/bindings/usb/usb251xb.txt +++ b/Documentation/devicetree/bindings/usb/usb251xb.txt @@ -64,10 +64,8 @@ Optional properties : - power-on-time-ms : Specifies the time it takes from the time the host initiates the power-on sequence to a port until the port has adequate power. The value is given in ms in a 0 - 510 range (default is 100ms). - - swap-dx-lanes : Specifies the downstream ports which will swap the - differential-pair (D+/D-), default is not-swapped. - - swap-us-lanes : Selects the upstream port differential-pair (D+/D-) - swapping (boolean, default is not-swapped) + - swap-dx-lanes : Specifies the ports which will swap the differential-pair + (D+/D-), default is not-swapped. Examples: usb2512b@2c { diff --git a/Documentation/devicetree/bindings/usb/usbmisc-imx.txt b/Documentation/devicetree/bindings/usb/usbmisc-imx.txt index a85a631ec434..b353b9816487 100644 --- a/Documentation/devicetree/bindings/usb/usbmisc-imx.txt +++ b/Documentation/devicetree/bindings/usb/usbmisc-imx.txt @@ -7,6 +7,7 @@ Required properties: "fsl,vf610-usbmisc" for Vybrid vf610 "fsl,imx6sx-usbmisc" for imx6sx "fsl,imx7d-usbmisc" for imx7d + "fsl,imx7ulp-usbmisc" for imx7ulp - reg: Should contain registers location and length Examples: diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index 33a65a45e319..967e78c5ec0a 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -27,6 +27,8 @@ patternProperties: description: Abilis Systems "^abracon,.*": description: Abracon Corporation + "^acme,.*": + description: Acme Systems srl "^actions,.*": description: Actions Semiconductor Co., Ltd. "^active-semi,.*": @@ -49,6 +51,8 @@ patternProperties: description: Aeroflex Gaisler AB "^al,.*": description: Annapurna Labs + "^allegro,.*": + description: Allegro DVT "^allo,.*": description: Allo.com "^allwinner,.*": @@ -79,6 +83,8 @@ patternProperties: description: Analogix Semiconductor, Inc. "^andestech,.*": description: Andes Technology Corporation + "^anvo,.*": + description: Anvo-Systems Dresden GmbH "^apm,.*": description: Applied Micro Circuits Corporation (APM) "^aptina,.*": @@ -147,6 +153,8 @@ patternProperties: description: Broadcom Corporation "^buffalo,.*": description: Buffalo, Inc. + "^bur,.*": + description: B&R Industrial Automation GmbH "^bticino,.*": description: Bticino International "^calxeda,.*": @@ -175,6 +183,8 @@ patternProperties: description: Common Hardware Reference Platform "^chunghwa,.*": description: Chunghwa Picture Tubes Ltd. + "^chuwi,.*": + description: Chuwi Innovation Ltd. "^ciaa,.*": description: Computadora Industrial Abierta Argentina "^cirrus,.*": @@ -185,8 +195,12 @@ patternProperties: description: Chips&Media, Inc. "^cnxt,.*": description: Conexant Systems, Inc. + "^colorfly,.*": + description: Colorful GRP, Shenzhen Xueyushi Technology Ltd. "^compulab,.*": description: CompuLab Ltd. + "^corpro,.*": + description: Chengdu Corpro Technology Co., Ltd. "^cortina,.*": description: Cortina Systems, Inc. "^cosmic,.*": @@ -199,6 +213,8 @@ patternProperties: description: Crystalfontz America, Inc. "^csky,.*": description: Hangzhou C-SKY Microsystems Co., Ltd + "^csq,.*": + description: Shenzen Chuangsiqi Technology Co.,Ltd. "^cubietech,.*": description: Cubietech, Ltd. "^cypress,.*": @@ -219,6 +235,8 @@ patternProperties: description: Devantech, Ltd. "^dh,.*": description: DH electronics GmbH + "^difrnce,.*": + description: Shenzhen Yagu Electronic Technology Co., Ltd. "^digi,.*": description: Digi International Inc. "^digilent,.*": @@ -241,6 +259,8 @@ patternProperties: description: DPTechnics "^dragino,.*": description: Dragino Technology Co., Limited + "^dserve,.*": + description: dServe Technology B.V. "^ea,.*": description: Embedded Artists AB "^ebs-systart,.*": @@ -253,6 +273,8 @@ patternProperties: description: Emerging Display Technologies "^eeti,.*": description: eGalax_eMPIA Technology Inc + "^einfochips,.*": + description: Einfochips "^elan,.*": description: Elan Microelectronic Corp. "^elgin,.*": @@ -263,6 +285,8 @@ patternProperties: description: Emlid, Ltd. "^emmicro,.*": description: EM Microelectronic + "^empire-electronix,.*": + description: Empire Electronix "^emtrion,.*": description: emtrion GmbH "^endless,.*": @@ -277,6 +301,8 @@ patternProperties: description: Ecole Polytechnique Fédérale de Lausanne "^epson,.*": description: Seiko Epson Corp. + "^esp,.*": + description: Espressif Systems Co. Ltd. "^est,.*": description: ESTeem Wireless Modems "^ettus,.*": @@ -287,6 +313,8 @@ patternProperties: description: Everest Semiconductor Co. Ltd. "^everspin,.*": description: Everspin Technologies, Inc. + "^evervision,.*": + description: Evervision Electronics Co. Ltd. "^exar,.*": description: Exar Corporation "^excito,.*": @@ -327,6 +355,8 @@ patternProperties: description: GE Fanuc Intelligent Platforms Embedded Systems, Inc. "^GEFanuc,.*": description: GE Fanuc Intelligent Platforms Embedded Systems, Inc. + "^gemei,.*": + description: Gemei Digital Technology Co., Ltd. "^geniatech,.*": description: Geniatech, Inc. "^giantec,.*": @@ -371,12 +401,20 @@ patternProperties: description: Holt Integrated Circuits, Inc. "^honeywell,.*": description: Honeywell + "^hoperun,.*": + description: Jiangsu HopeRun Software Co., Ltd. "^hp,.*": description: Hewlett Packard + "^hsg,.*": + description: HannStar Display Co. "^holtek,.*": description: Holtek Semiconductor, Inc. + "^hugsun,.*": + description: Shenzhen Hugsun Technology Co. Ltd. "^hwacom,.*": description: HwaCom Systems Inc. + "^hyundai,.*": + description: Hyundai Technology "^i2se,.*": description: I2SE GmbH "^ibm,.*": @@ -391,6 +429,10 @@ patternProperties: description: ILI Technology Corporation (ILITEK) "^img,.*": description: Imagination Technologies Ltd. + "^incircuit,.*": + description: In-Circuit GmbH + "^inet-tek,.*": + description: Shenzhen iNet Mobile Internet Technology Co., Ltd "^infineon,.*": description: Infineon Technologies "^inforce,.*": @@ -401,6 +443,8 @@ patternProperties: description: Innolux Corporation "^inside-secure,.*": description: INSIDE Secure + "^inspur,.*": + description: Inspur Corporation "^intel,.*": description: Intel Corporation "^intercontrol,.*": @@ -425,6 +469,8 @@ patternProperties: description: Japan Display Inc. "^jedec,.*": description: JEDEC Solid State Technology Association + "^jesurun,.*": + description: Shenzhen Jesurun Electronics Business Dept. "^jianda,.*": description: Jiandangjing Technology Co., Ltd. "^karo,.*": @@ -449,6 +495,8 @@ patternProperties: description: Rakuten Kobo Inc. "^koe,.*": description: Kaohsiung Opto-Electronics Inc. + "^kontron,.*": + description: Kontron S&T AG "^kosagi,.*": description: Sutajio Ko-Usagi PTE Ltd. "^kyo,.*": @@ -457,10 +505,14 @@ patternProperties: description: LaCie "^laird,.*": description: Laird PLC + "^lamobo,.*": + description: Ketai Huajie Technology Co., Ltd. "^lantiq,.*": description: Lantiq Semiconductor "^lattice,.*": description: Lattice Semiconductor + "^leez,.*": + description: Leez "^lego,.*": description: LEGO Systems A/S "^lemaker,.*": @@ -469,12 +521,16 @@ patternProperties: description: Lenovo Group Ltd. "^lg,.*": description: LG Corporation + "^lgphilips,.*": + description: LG Display "^libretech,.*": description: Shenzhen Libre Technology Co., Ltd "^licheepi,.*": description: Lichee Pi "^linaro,.*": description: Linaro Limited + "^linksprite,.*": + description: LinkSprite Technologies, Inc. "^linksys,.*": description: Belkin International, Inc. (Linksys) "^linux,.*": @@ -485,12 +541,16 @@ patternProperties: description: Linear Technology Corporation "^logicpd,.*": description: Logic PD, Inc. + "^longcheer,.*": + description: Longcheer Technology (Shanghai) Co., Ltd. "^lsi,.*": description: LSI Corp. (LSI Logic) "^lwn,.*": description: Liebherr-Werk Nenzing GmbH "^macnica,.*": description: Macnica Americas + "^mapleboard,.*": + description: Mapleboard.org "^marvell,.*": description: Marvell Technology Group Ltd. "^maxbotix,.*": @@ -503,6 +563,8 @@ patternProperties: description: mCube "^meas,.*": description: Measurement Specialties + "^mecer,.*": + description: Mustek Limited "^mediatek,.*": description: MediaTek Inc. "^megachips,.*": @@ -529,8 +591,12 @@ patternProperties: description: Micro Crystal AG "^micron,.*": description: Micron Technology Inc. + "^microsoft,.*": + description: Microsoft Corporation "^mikroe,.*": description: MikroElektronika d.o.o. + "^miniand,.*": + description: Miniand Tech "^minix,.*": description: MINIX Technology Ltd. "^miramems,.*": @@ -661,28 +727,38 @@ patternProperties: description: Picochip Ltd "^pine64,.*": description: Pine64 + "^pineriver,.*": + description: Shenzhen PineRiver Designs Co., Ltd. "^pixcir,.*": description: PIXCIR MICROELECTRONICS Co., Ltd "^plantower,.*": description: Plantower Co., Ltd "^plathome,.*": - description: Plat'Home Co., Ltd. + description: Plat\'Home Co., Ltd. "^plda,.*": description: PLDA "^plx,.*": description: Broadcom Corporation (formerly PLX Technology) "^pni,.*": description: PNI Sensor Corporation + "^polaroid,.*": + description: Polaroid Corporation "^portwell,.*": description: Portwell Inc. "^poslab,.*": description: Poslab Technology Co., Ltd. + "^pov,.*": + description: Point of View International B.V. "^powervr,.*": description: PowerVR (deprecated, use img) + "^primux,.*": + description: Primux Trading, S.L. "^probox2,.*": description: PROBOX2 (by W2COMP Co., Ltd.) "^pulsedlight,.*": description: PulsedLight, Inc + "^purism,.*": + description: Purism, SPC "^qca,.*": description: Qualcomm Atheros, Inc. "^qcom,.*": @@ -691,6 +767,8 @@ patternProperties: description: QEMU, a generic and open source machine emulator and virtualizer "^qi,.*": description: Qi Hardware + "^qihua,.*": + description: Chengdu Kaixuan Information Technology Co., Ltd. "^qiaodian,.*": description: QiaoDian XianShi Corporation "^qnap,.*": @@ -713,6 +791,8 @@ patternProperties: description: Realtek Semiconductor Corp. "^renesas,.*": description: Renesas Electronics Corporation + "^rervision,.*": + description: Shenzhen Rervision Technology Co., Ltd. "^richtek,.*": description: Richtek Technology Corporation "^ricoh,.*": @@ -751,6 +831,8 @@ patternProperties: description: Semtech Corporation "^sensirion,.*": description: Sensirion AG + "^sensortek,.*": + description: Sensortek Technology Corporation "^sff,.*": description: Small Form Factor Committee "^sgd,.*": @@ -781,8 +863,14 @@ patternProperties: description: Silergy Corp. "^siliconmitus,.*": description: Silicon Mitus, Inc. - "^simte,.*": - description: k + "^simtek,.*": + description: Cypress Semiconductor Corporation (Simtek Corporation) + "^sinlinx,.*": + description: Sinlinx Electronics Technology Co., LTD + "^sinovoip,.*": + description: SinoVoip Co., Ltd + "^sipeed,.*": + description: Shenzhen Sipeed Technology Co., Ltd. "^sirf,.*": description: SiRF Technology, Inc. "^sis,.*": @@ -795,6 +883,8 @@ patternProperties: description: Standard Microsystems Corporation "^snps,.*": description: Synopsys, Inc. + "^sochip,.*": + description: Shenzhen SoChip Technology Co., Ltd. "^socionext,.*": description: Socionext Inc. "^solidrun,.*": @@ -849,6 +939,8 @@ patternProperties: description: Shenzhen Techstar Electronics Co., Ltd. "^terasic,.*": description: Terasic Inc. + "^tfc,.*": + description: Three Five Corp "^thine,.*": description: THine Electronics, Inc. "^ti,.*": @@ -861,6 +953,9 @@ patternProperties: description: Tecon Microprocessor Technologies, LLC. "^topeet,.*": description: Topeet + "^toppoly,.*": + description: TPO (deprecated, use tpo) + deprecated: true "^toradex,.*": description: Toradex AG "^toshiba,.*": @@ -901,6 +996,8 @@ patternProperties: description: United Radiant Technology Corporation "^usi,.*": description: Universal Scientific Industrial Co., Ltd. + "^utoo,.*": + description: Aigo Digital Technology Co., Ltd. "^v3,.*": description: V3 Semiconductor "^vamrs,.*": @@ -923,6 +1020,8 @@ patternProperties: description: Voipac Technologies s.r.o. "^vot,.*": description: Vision Optical Technology Co., Ltd. + "^vxt,.*": + description: VXT Ltd "^wd,.*": description: Western Digital Corp. "^wetek,.*": @@ -937,10 +1036,14 @@ patternProperties: description: Winbond Electronics corp. "^winstar,.*": description: Winstar Display Corp. + "^wits,.*": + description: Shenzhen Merrii Technology Co., Ltd. (WITS) "^wlf,.*": description: Wolfson Microelectronics "^wm,.*": description: Wondermedia Technologies, Inc. + "^wobo,.*": + description: Wobo "^x-powers,.*": description: X-Powers "^xes,.*": @@ -951,6 +1054,8 @@ patternProperties: description: Xilinx "^xunlong,.*": description: Shenzhen Xunlong Software CO.,Limited + "^yones-toptech,.*": + description: Yones Toptech Co., Ltd. "^ysoft,.*": description: Y Soft Corporation a.s. "^zarlink,.*": @@ -968,7 +1073,7 @@ patternProperties: # Normal property name match without a comma # These should catch all node/property names without a prefix - "^[a-zA-Z0-9#][a-zA-Z0-9+\\-._@]{0,63}$": true + "^[a-zA-Z0-9#_][a-zA-Z0-9+\\-._@]{0,63}$": true "^[a-zA-Z0-9+\\-._]*@[0-9a-zA-Z,]*$": true "^#.*": true diff --git a/Documentation/devicetree/bindings/virtio/iommu.txt b/Documentation/devicetree/bindings/virtio/iommu.txt new file mode 100644 index 000000000000..2407fea0651c --- /dev/null +++ b/Documentation/devicetree/bindings/virtio/iommu.txt @@ -0,0 +1,66 @@ +* virtio IOMMU PCI device + +When virtio-iommu uses the PCI transport, its programming interface is +discovered dynamically by the PCI probing infrastructure. However the +device tree statically describes the relation between IOMMU and DMA +masters. Therefore, the PCI root complex that hosts the virtio-iommu +contains a child node representing the IOMMU device explicitly. + +Required properties: + +- compatible: Should be "virtio,pci-iommu" +- reg: PCI address of the IOMMU. As defined in the PCI Bus + Binding reference [1], the reg property is a five-cell + address encoded as (phys.hi phys.mid phys.lo size.hi + size.lo). phys.hi should contain the device's BDF as + 0b00000000 bbbbbbbb dddddfff 00000000. The other cells + should be zero. +- #iommu-cells: Each platform DMA master managed by the IOMMU is assigned + an endpoint ID, described by the "iommus" property [2]. + For virtio-iommu, #iommu-cells must be 1. + +Notes: + +- DMA from the IOMMU device isn't managed by another IOMMU. Therefore the + virtio-iommu node doesn't have an "iommus" property, and is omitted from + the iommu-map property of the root complex. + +Example: + +pcie@10000000 { + compatible = "pci-host-ecam-generic"; + ... + + /* The IOMMU programming interface uses slot 00:01.0 */ + iommu0: iommu@0008 { + compatible = "virtio,pci-iommu"; + reg = <0x00000800 0 0 0 0>; + #iommu-cells = <1>; + }; + + /* + * The IOMMU manages all functions in this PCI domain except + * itself. Omit BDF 00:01.0. + */ + iommu-map = <0x0 &iommu0 0x0 0x8> + <0x9 &iommu0 0x9 0xfff7>; +}; + +pcie@20000000 { + compatible = "pci-host-ecam-generic"; + ... + /* + * The IOMMU also manages all functions from this domain, + * with endpoint IDs 0x10000 - 0x1ffff + */ + iommu-map = <0x0 &iommu0 0x10000 0x10000>; +}; + +ethernet@fe001000 { + ... + /* The IOMMU manages this platform device with endpoint ID 0x20000 */ + iommus = <&iommu0 0x20000>; +}; + +[1] Documentation/devicetree/bindings/pci/pci.txt +[2] Documentation/devicetree/bindings/iommu/iommu.txt diff --git a/Documentation/devicetree/bindings/virtio/mmio.txt b/Documentation/devicetree/bindings/virtio/mmio.txt index 5069c1b8e193..21af30fbb81f 100644 --- a/Documentation/devicetree/bindings/virtio/mmio.txt +++ b/Documentation/devicetree/bindings/virtio/mmio.txt @@ -8,10 +8,40 @@ Required properties: - reg: control registers base address and size including configuration space - interrupts: interrupt generated by the device +Required properties for virtio-iommu: + +- #iommu-cells: When the node corresponds to a virtio-iommu device, it is + linked to DMA masters using the "iommus" or "iommu-map" + properties [1][2]. #iommu-cells specifies the size of the + "iommus" property. For virtio-iommu #iommu-cells must be + 1, each cell describing a single endpoint ID. + +Optional properties: + +- iommus: If the device accesses memory through an IOMMU, it should + have an "iommus" property [1]. Since virtio-iommu itself + does not access memory through an IOMMU, the "virtio,mmio" + node cannot have both an "#iommu-cells" and an "iommus" + property. + Example: virtio_block@3000 { compatible = "virtio,mmio"; reg = <0x3000 0x100>; interrupts = <41>; + + /* Device has endpoint ID 23 */ + iommus = <&viommu 23> } + + viommu: iommu@3100 { + compatible = "virtio,mmio"; + reg = <0x3100 0x100>; + interrupts = <42>; + + #iommu-cells = <1> + } + +[1] Documentation/devicetree/bindings/iommu/iommu.txt +[2] Documentation/devicetree/bindings/pci/pci-iommu.txt diff --git a/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml b/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml new file mode 100644 index 000000000000..3a54f58683a0 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml @@ -0,0 +1,58 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/watchdog/allwinner,sun4i-a10-wdt.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 Watchdog Device Tree Bindings + +allOf: + - $ref: "watchdog.yaml#" + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + compatible: + oneOf: + - const: allwinner,sun4i-a10-wdt + - const: allwinner,sun6i-a31-wdt + - items: + - const: allwinner,sun50i-a64-wdt + - const: allwinner,sun6i-a31-wdt + - items: + - const: allwinner,sun50i-h6-wdt + - const: allwinner,sun6i-a31-wdt + - items: + - const: allwinner,suniv-f1c100s-wdt + - const: allwinner,sun4i-a10-wdt + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - clocks + - interrupts + +unevaluatedProperties: false + +examples: + - | + wdt: watchdog@1c20c90 { + compatible = "allwinner,sun4i-a10-wdt"; + reg = <0x01c20c90 0x10>; + interrupts = <24>; + clocks = <&osc24M>; + timeout-sec = <10>; + }; + +... diff --git a/Documentation/devicetree/bindings/watchdog/amlogic,meson-gxbb-wdt.yaml b/Documentation/devicetree/bindings/watchdog/amlogic,meson-gxbb-wdt.yaml new file mode 100644 index 000000000000..d7352f709b37 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/amlogic,meson-gxbb-wdt.yaml @@ -0,0 +1,37 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 BayLibre, SAS +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/watchdog/amlogic,meson-gxbb-wdt.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Meson GXBB SoCs Watchdog timer + +maintainers: + - Neil Armstrong <narmstrong@baylibre.com> + +properties: + compatible: + enum: + - amlogic,meson-gxbb-wdt + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + description: + A phandle to the clock of this PHY + +required: + - compatible + - reg + - clocks + +examples: + - | + watchdog@98d0 { + compatible = "amlogic,meson-gxbb-wdt"; + reg = <0x98d0 0x10>; + clocks = <&xtal>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt b/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt index c5077a1f5cb3..d78d4a8fb868 100644 --- a/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt @@ -4,6 +4,7 @@ Required properties: - compatible: must be one of: - "aspeed,ast2400-wdt" - "aspeed,ast2500-wdt" + - "aspeed,ast2600-wdt" - reg: physical base address of the controller and length of memory mapped region diff --git a/Documentation/devicetree/bindings/watchdog/fsl-imx-sc-wdt.txt b/Documentation/devicetree/bindings/watchdog/fsl-imx-sc-wdt.txt deleted file mode 100644 index 02b87e92ae68..000000000000 --- a/Documentation/devicetree/bindings/watchdog/fsl-imx-sc-wdt.txt +++ /dev/null @@ -1,24 +0,0 @@ -* Freescale i.MX System Controller Watchdog - -i.MX system controller watchdog is for i.MX SoCs with system controller inside, -the watchdog is managed by system controller, users can ONLY communicate with -system controller from secure mode for watchdog operations, so Linux i.MX system -controller watchdog driver will call ARM SMC API and trap into ARM-Trusted-Firmware -for watchdog operations, ARM-Trusted-Firmware is running at secure EL3 mode and -it will request system controller to execute the watchdog operation passed from -Linux kernel. - -Required properties: -- compatible: Should be : - "fsl,imx8qxp-sc-wdt" - followed by "fsl,imx-sc-wdt"; - -Optional properties: -- timeout-sec : Contains the watchdog timeout in seconds. - -Examples: - -watchdog { - compatible = "fsl,imx8qxp-sc-wdt", "fsl,imx-sc-wdt"; - timeout-sec = <60>; -}; diff --git a/Documentation/devicetree/bindings/watchdog/fsl-imx7ulp-wdt.txt b/Documentation/devicetree/bindings/watchdog/fsl-imx7ulp-wdt.txt new file mode 100644 index 000000000000..f902508d6cac --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/fsl-imx7ulp-wdt.txt @@ -0,0 +1,22 @@ +* Freescale i.MX7ULP Watchdog Timer (WDT) Controller + +Required properties: +- compatible : Should be "fsl,imx7ulp-wdt" +- reg : Should contain WDT registers location and length +- interrupts : Should contain WDT interrupt +- clocks: Should contain a phandle pointing to the gated peripheral clock. + +Optional properties: +- timeout-sec : Contains the watchdog timeout in seconds + +Examples: + +wdog1: watchdog@403d0000 { + compatible = "fsl,imx7ulp-wdt"; + reg = <0x403d0000 0x10000>; + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pcc2 IMX7ULP_CLK_WDG1>; + assigned-clocks = <&pcc2 IMX7ULP_CLK_WDG1>; + assigned-clocks-parents = <&scg1 IMX7ULP_CLK_FIRC_BUS_CLK>; + timeout-sec = <40>; +}; diff --git a/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt b/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt deleted file mode 100644 index ce1cb72d5345..000000000000 --- a/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt +++ /dev/null @@ -1,17 +0,0 @@ -Ingenic Watchdog Timer (WDT) Controller for JZ4740 & JZ4780 - -Required properties: -compatible: "ingenic,jz4740-watchdog" or "ingenic,jz4780-watchdog" -reg: Register address and length for watchdog registers -clocks: phandle to the RTC clock -clock-names: should be "rtc" - -Example: - -watchdog: jz4740-watchdog@10002000 { - compatible = "ingenic,jz4740-watchdog"; - reg = <0x10002000 0x10>; - - clocks = <&cgu JZ4740_CLK_RTC>; - clock-names = "rtc"; -}; diff --git a/Documentation/devicetree/bindings/watchdog/meson-gxbb-wdt.txt b/Documentation/devicetree/bindings/watchdog/meson-gxbb-wdt.txt deleted file mode 100644 index c7fe36fa739c..000000000000 --- a/Documentation/devicetree/bindings/watchdog/meson-gxbb-wdt.txt +++ /dev/null @@ -1,16 +0,0 @@ -Meson GXBB SoCs Watchdog timer - -Required properties: - -- compatible : should be "amlogic,meson-gxbb-wdt" -- reg : Specifies base physical address and size of the registers. -- clocks : Should be a phandle to the Watchdog clock source, for GXBB the xtal - is the default clock source. - -Example: - -wdt: watchdog@98d0 { - compatible = "amlogic,meson-gxbb-wdt"; - reg = <0 0x98d0 0x0 0x10>; - clocks = <&xtal>; -}; diff --git a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt b/Documentation/devicetree/bindings/watchdog/renesas,wdt.txt index 9f365c1a3399..9f365c1a3399 100644 --- a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/renesas,wdt.txt diff --git a/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt b/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt deleted file mode 100644 index 46055254e8dd..000000000000 --- a/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt +++ /dev/null @@ -1,21 +0,0 @@ -Allwinner SoCs Watchdog timer - -Required properties: - -- compatible : should be one of - "allwinner,sun4i-a10-wdt" - "allwinner,sun6i-a31-wdt" - "allwinner,sun50i-a64-wdt","allwinner,sun6i-a31-wdt" - "allwinner,suniv-f1c100s-wdt", "allwinner,sun4i-a10-wdt" -- reg : Specifies base physical address and size of the registers. - -Optional properties: -- timeout-sec : Contains the watchdog timeout in seconds - -Example: - -wdt: watchdog@1c20c90 { - compatible = "allwinner,sun4i-a10-wdt"; - reg = <0x01c20c90 0x10>; - timeout-sec = <10>; -}; diff --git a/Documentation/devicetree/bindings/watchdog/watchdog.yaml b/Documentation/devicetree/bindings/watchdog/watchdog.yaml new file mode 100644 index 000000000000..187bf6cb62bf --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/watchdog.yaml @@ -0,0 +1,26 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/watchdog/watchdog.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Watchdog Generic Bindings + +maintainers: + - Guenter Roeck <linux@roeck-us.net> + - Wim Van Sebroeck <wim@linux-watchdog.org> + +description: | + This document describes generic bindings which can be used to + describe watchdog devices in a device tree. + +properties: + $nodename: + pattern: "^watchdog(@.*|-[0-9a-f])?$" + + timeout-sec: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Contains the watchdog timeout in seconds. + +... |