diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
30 files changed, 705 insertions, 69 deletions
diff --git a/Documentation/devicetree/bindings/clock/uniphier-clock.txt b/Documentation/devicetree/bindings/clock/uniphier-clock.txt index c7179d3b5c33..812163060fa3 100644 --- a/Documentation/devicetree/bindings/clock/uniphier-clock.txt +++ b/Documentation/devicetree/bindings/clock/uniphier-clock.txt @@ -24,7 +24,7 @@ Example: reg = <0x61840000 0x4000>; clock { - compatible = "socionext,uniphier-ld20-clock"; + compatible = "socionext,uniphier-ld11-clock"; #clock-cells = <1>; }; @@ -43,8 +43,8 @@ Provided clocks: 21: USB3 ch1 PHY1 -Media I/O (MIO) clock ---------------------- +Media I/O (MIO) clock, SD clock +------------------------------- Required properties: - compatible: should be one of the following: @@ -52,10 +52,10 @@ Required properties: "socionext,uniphier-ld4-mio-clock" - for LD4 SoC. "socionext,uniphier-pro4-mio-clock" - for Pro4 SoC. "socionext,uniphier-sld8-mio-clock" - for sLD8 SoC. - "socionext,uniphier-pro5-mio-clock" - for Pro5 SoC. - "socionext,uniphier-pxs2-mio-clock" - for PXs2/LD6b SoC. + "socionext,uniphier-pro5-sd-clock" - for Pro5 SoC. + "socionext,uniphier-pxs2-sd-clock" - for PXs2/LD6b SoC. "socionext,uniphier-ld11-mio-clock" - for LD11 SoC. - "socionext,uniphier-ld20-mio-clock" - for LD20 SoC. + "socionext,uniphier-ld20-sd-clock" - for LD20 SoC. - #clock-cells: should be 1. Example: @@ -66,7 +66,7 @@ Example: reg = <0x59810000 0x800>; clock { - compatible = "socionext,uniphier-ld20-mio-clock"; + compatible = "socionext,uniphier-ld11-mio-clock"; #clock-cells = <1>; }; @@ -112,7 +112,7 @@ Example: reg = <0x59820000 0x200>; clock { - compatible = "socionext,uniphier-ld20-peri-clock"; + compatible = "socionext,uniphier-ld11-peri-clock"; #clock-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-ibt-bmc.txt b/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-ibt-bmc.txt new file mode 100644 index 000000000000..6f28969af9dc --- /dev/null +++ b/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-ibt-bmc.txt @@ -0,0 +1,23 @@ +* Aspeed BT (Block Transfer) IPMI interface + +The Aspeed SOCs (AST2400 and AST2500) are commonly used as BMCs +(BaseBoard Management Controllers) and the BT interface can be used to +perform in-band IPMI communication with their host. + +Required properties: + +- compatible : should be "aspeed,ast2400-ibt-bmc" +- reg: physical address and size of the registers + +Optional properties: + +- interrupts: interrupt generated by the BT interface. without an + interrupt, the driver will operate in poll mode. + +Example: + + ibt@1e789140 { + compatible = "aspeed,ast2400-ibt-bmc"; + reg = <0x1e789140 0x18>; + interrupts = <8>; + }; diff --git a/Documentation/devicetree/bindings/ipmi.txt b/Documentation/devicetree/bindings/ipmi/ipmi-smic.txt index d5f1a877ed3e..d5f1a877ed3e 100644 --- a/Documentation/devicetree/bindings/ipmi.txt +++ b/Documentation/devicetree/bindings/ipmi/ipmi-smic.txt diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt index 4e00e859e885..bfa461aaac99 100644 --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt @@ -43,6 +43,9 @@ Optional properties: reset signal present internally in some host controller IC designs. See Documentation/devicetree/bindings/reset/reset.txt for details. +* reset-names: request name for using "resets" property. Must be "reset". + (It will be used together with "resets" property.) + * clocks: from common clock binding: handle to biu and ciu clocks for the bus interface unit clock and the card interface unit clock. @@ -103,6 +106,8 @@ board specific portions as listed below. interrupts = <0 75 0>; #address-cells = <1>; #size-cells = <0>; + resets = <&rst 20>; + reset-names = "reset"; }; [board specific internal DMA resources] diff --git a/Documentation/devicetree/bindings/net/ethernet.txt b/Documentation/devicetree/bindings/net/ethernet.txt index e1d76812419c..05150957ecfd 100644 --- a/Documentation/devicetree/bindings/net/ethernet.txt +++ b/Documentation/devicetree/bindings/net/ethernet.txt @@ -9,10 +9,26 @@ The following properties are common to the Ethernet controllers: - max-speed: number, specifies maximum speed in Mbit/s supported by the device; - max-frame-size: number, maximum transfer unit (IEEE defined MTU), rather than the maximum frame size (there's contradiction in ePAPR). -- phy-mode: string, operation mode of the PHY interface; supported values are - "mii", "gmii", "sgmii", "qsgmii", "tbi", "rev-mii", "rmii", "rgmii", "rgmii-id", - "rgmii-rxid", "rgmii-txid", "rtbi", "smii", "xgmii", "trgmii"; this is now a - de-facto standard property; +- phy-mode: string, operation mode of the PHY interface. This is now a de-facto + standard property; supported values are: + * "mii" + * "gmii" + * "sgmii" + * "qsgmii" + * "tbi" + * "rev-mii" + * "rmii" + * "rgmii" (RX and TX delays are added by the MAC when required) + * "rgmii-id" (RGMII with internal RX and TX delays provided by the PHY, the + MAC should not add the RX or TX delays in this case) + * "rgmii-rxid" (RGMII with internal RX delay provided by the PHY, the MAC + should not add an RX delay in this case) + * "rgmii-txid" (RGMII with internal TX delay provided by the PHY, the MAC + should not add an TX delay in this case) + * "rtbi" + * "smii" + * "xgmii" + * "trgmii" - phy-connection-type: the same as "phy-mode" property but described in ePAPR; - phy-handle: phandle, specifies a reference to a node representing a PHY device; this property is described in ePAPR and so preferred; diff --git a/Documentation/devicetree/bindings/net/marvell-orion-net.txt b/Documentation/devicetree/bindings/net/marvell-orion-net.txt index bce52b2ec55e..6fd988c84c4f 100644 --- a/Documentation/devicetree/bindings/net/marvell-orion-net.txt +++ b/Documentation/devicetree/bindings/net/marvell-orion-net.txt @@ -49,6 +49,7 @@ Optional port properties: and - phy-handle: See ethernet.txt file in the same directory. + - phy-mode: See ethernet.txt file in the same directory. or diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt index ba67b39939c1..71aeda1ca055 100644 --- a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt +++ b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt @@ -26,13 +26,16 @@ Required properties: - "sys" - "legacy" - "client" -- resets: Must contain five entries for each entry in reset-names. +- resets: Must contain seven entries for each entry in reset-names. See ../reset/reset.txt for details. - reset-names: Must include the following names - "core" - "mgmt" - "mgmt-sticky" - "pipe" + - "pm" + - "aclk" + - "pclk" - pinctrl-names : The pin control state names - pinctrl-0: The "default" pinctrl state - #interrupt-cells: specifies the number of cells needed to encode an @@ -86,8 +89,10 @@ pcie0: pcie@f8000000 { reg = <0x0 0xf8000000 0x0 0x2000000>, <0x0 0xfd000000 0x0 0x1000000>; reg-names = "axi-base", "apb-base"; resets = <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>, - <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>; - reset-names = "core", "mgmt", "mgmt-sticky", "pipe"; + <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE> , + <&cru SRST_PCIE_PM>, <&cru SRST_P_PCIE>, <&cru SRST_A_PCIE>; + reset-names = "core", "mgmt", "mgmt-sticky", "pipe", + "pm", "pclk", "aclk"; phys = <&pcie_phy>; phy-names = "pcie-phy"; pinctrl-names = "default"; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt index 5e60ad18f147..2ad18c4ea55c 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt @@ -43,7 +43,9 @@ aspeed,ast2500-pinctrl, aspeed,g5-pinctrl: GPID0 GPID2 GPIE0 I2C10 I2C11 I2C12 I2C13 I2C14 I2C3 I2C4 I2C5 I2C6 I2C7 I2C8 I2C9 MAC1LINK MDIO1 MDIO2 OSCCLK PEWAKE PWM0 PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 -RGMII1 RGMII2 RMII1 RMII2 SD1 SPI1 TIMER4 TIMER5 TIMER6 TIMER7 TIMER8 +RGMII1 RGMII2 RMII1 RMII2 SD1 SPI1 SPI1DEBUG SPI1PASSTHRU TIMER4 TIMER5 TIMER6 +TIMER7 TIMER8 VGABIOSROM + Examples: diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt index f9753c416974..b24583aa34c3 100644 --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt @@ -14,11 +14,6 @@ Required properies: - #size-cells : The value of this property must be 1 - ranges : defines mapping between pin controller node (parent) to gpio-bank node (children). - - interrupt-parent: phandle of the interrupt parent to which the external - GPIO interrupts are forwarded to. - - st,syscfg: Should be phandle/offset pair. The phandle to the syscon node - which includes IRQ mux selection register, and the offset of the IRQ mux - selection register. - pins-are-numbered: Specify the subnodes are using numbered pinmux to specify pins. @@ -37,6 +32,11 @@ Required properties: Optional properties: - reset: : Reference to the reset controller + - interrupt-parent: phandle of the interrupt parent to which the external + GPIO interrupts are forwarded to. + - st,syscfg: Should be phandle/offset pair. The phandle to the syscon node + which includes IRQ mux selection register, and the offset of the IRQ mux + selection register. Example: #include <dt-bindings/pinctrl/stm32f429-pinfunc.h> diff --git a/Documentation/devicetree/bindings/reset/uniphier-reset.txt b/Documentation/devicetree/bindings/reset/uniphier-reset.txt index e6bbfccd56c3..5020524cddeb 100644 --- a/Documentation/devicetree/bindings/reset/uniphier-reset.txt +++ b/Documentation/devicetree/bindings/reset/uniphier-reset.txt @@ -6,25 +6,25 @@ System reset Required properties: - compatible: should be one of the following: - "socionext,uniphier-sld3-reset" - for PH1-sLD3 SoC. - "socionext,uniphier-ld4-reset" - for PH1-LD4 SoC. - "socionext,uniphier-pro4-reset" - for PH1-Pro4 SoC. - "socionext,uniphier-sld8-reset" - for PH1-sLD8 SoC. - "socionext,uniphier-pro5-reset" - for PH1-Pro5 SoC. - "socionext,uniphier-pxs2-reset" - for ProXstream2/PH1-LD6b SoC. - "socionext,uniphier-ld11-reset" - for PH1-LD11 SoC. - "socionext,uniphier-ld20-reset" - for PH1-LD20 SoC. + "socionext,uniphier-sld3-reset" - for sLD3 SoC. + "socionext,uniphier-ld4-reset" - for LD4 SoC. + "socionext,uniphier-pro4-reset" - for Pro4 SoC. + "socionext,uniphier-sld8-reset" - for sLD8 SoC. + "socionext,uniphier-pro5-reset" - for Pro5 SoC. + "socionext,uniphier-pxs2-reset" - for PXs2/LD6b SoC. + "socionext,uniphier-ld11-reset" - for LD11 SoC. + "socionext,uniphier-ld20-reset" - for LD20 SoC. - #reset-cells: should be 1. Example: sysctrl@61840000 { - compatible = "socionext,uniphier-ld20-sysctrl", + compatible = "socionext,uniphier-ld11-sysctrl", "simple-mfd", "syscon"; reg = <0x61840000 0x4000>; reset { - compatible = "socionext,uniphier-ld20-reset"; + compatible = "socionext,uniphier-ld11-reset"; #reset-cells = <1>; }; @@ -32,30 +32,30 @@ Example: }; -Media I/O (MIO) reset ---------------------- +Media I/O (MIO) reset, SD reset +------------------------------- Required properties: - compatible: should be one of the following: - "socionext,uniphier-sld3-mio-reset" - for PH1-sLD3 SoC. - "socionext,uniphier-ld4-mio-reset" - for PH1-LD4 SoC. - "socionext,uniphier-pro4-mio-reset" - for PH1-Pro4 SoC. - "socionext,uniphier-sld8-mio-reset" - for PH1-sLD8 SoC. - "socionext,uniphier-pro5-mio-reset" - for PH1-Pro5 SoC. - "socionext,uniphier-pxs2-mio-reset" - for ProXstream2/PH1-LD6b SoC. - "socionext,uniphier-ld11-mio-reset" - for PH1-LD11 SoC. - "socionext,uniphier-ld20-mio-reset" - for PH1-LD20 SoC. + "socionext,uniphier-sld3-mio-reset" - for sLD3 SoC. + "socionext,uniphier-ld4-mio-reset" - for LD4 SoC. + "socionext,uniphier-pro4-mio-reset" - for Pro4 SoC. + "socionext,uniphier-sld8-mio-reset" - for sLD8 SoC. + "socionext,uniphier-pro5-sd-reset" - for Pro5 SoC. + "socionext,uniphier-pxs2-sd-reset" - for PXs2/LD6b SoC. + "socionext,uniphier-ld11-mio-reset" - for LD11 SoC. + "socionext,uniphier-ld20-sd-reset" - for LD20 SoC. - #reset-cells: should be 1. Example: mioctrl@59810000 { - compatible = "socionext,uniphier-ld20-mioctrl", + compatible = "socionext,uniphier-ld11-mioctrl", "simple-mfd", "syscon"; reg = <0x59810000 0x800>; reset { - compatible = "socionext,uniphier-ld20-mio-reset"; + compatible = "socionext,uniphier-ld11-mio-reset"; #reset-cells = <1>; }; @@ -68,24 +68,24 @@ Peripheral reset Required properties: - compatible: should be one of the following: - "socionext,uniphier-ld4-peri-reset" - for PH1-LD4 SoC. - "socionext,uniphier-pro4-peri-reset" - for PH1-Pro4 SoC. - "socionext,uniphier-sld8-peri-reset" - for PH1-sLD8 SoC. - "socionext,uniphier-pro5-peri-reset" - for PH1-Pro5 SoC. - "socionext,uniphier-pxs2-peri-reset" - for ProXstream2/PH1-LD6b SoC. - "socionext,uniphier-ld11-peri-reset" - for PH1-LD11 SoC. - "socionext,uniphier-ld20-peri-reset" - for PH1-LD20 SoC. + "socionext,uniphier-ld4-peri-reset" - for LD4 SoC. + "socionext,uniphier-pro4-peri-reset" - for Pro4 SoC. + "socionext,uniphier-sld8-peri-reset" - for sLD8 SoC. + "socionext,uniphier-pro5-peri-reset" - for Pro5 SoC. + "socionext,uniphier-pxs2-peri-reset" - for PXs2/LD6b SoC. + "socionext,uniphier-ld11-peri-reset" - for LD11 SoC. + "socionext,uniphier-ld20-peri-reset" - for LD20 SoC. - #reset-cells: should be 1. Example: perictrl@59820000 { - compatible = "socionext,uniphier-ld20-perictrl", + compatible = "socionext,uniphier-ld11-perictrl", "simple-mfd", "syscon"; reg = <0x59820000 0x200>; reset { - compatible = "socionext,uniphier-ld20-peri-reset"; + compatible = "socionext,uniphier-ld11-peri-reset"; #reset-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/serial/cdns,uart.txt b/Documentation/devicetree/bindings/serial/cdns,uart.txt index a3eb154c32ca..227bb770b027 100644 --- a/Documentation/devicetree/bindings/serial/cdns,uart.txt +++ b/Documentation/devicetree/bindings/serial/cdns,uart.txt @@ -1,7 +1,9 @@ Binding for Cadence UART Controller Required properties: -- compatible : should be "cdns,uart-r1p8", or "xlnx,xuartps" +- compatible : + Use "xlnx,xuartps","cdns,uart-r1p8" for Zynq-7xxx SoC. + Use "xlnx,zynqmp-uart","cdns,uart-r1p12" for Zynq Ultrascale+ MPSoC. - reg: Should contain UART controller registers location and length. - interrupts: Should contain UART controller interrupts. - clocks: Must contain phandles to the UART clocks diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index 1e4000d83aee..8d27d1a603e7 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -9,6 +9,14 @@ Required properties: - "renesas,scifb-r8a73a4" for R8A73A4 (R-Mobile APE6) SCIFB compatible UART. - "renesas,scifa-r8a7740" for R8A7740 (R-Mobile A1) SCIFA compatible UART. - "renesas,scifb-r8a7740" for R8A7740 (R-Mobile A1) SCIFB compatible UART. + - "renesas,scif-r8a7743" for R8A7743 (RZ/G1M) SCIF compatible UART. + - "renesas,scifa-r8a7743" for R8A7743 (RZ/G1M) SCIFA compatible UART. + - "renesas,scifb-r8a7743" for R8A7743 (RZ/G1M) SCIFB compatible UART. + - "renesas,hscif-r8a7743" for R8A7743 (RZ/G1M) HSCIF compatible UART. + - "renesas,scif-r8a7745" for R8A7745 (RZ/G1E) SCIF compatible UART. + - "renesas,scifa-r8a7745" for R8A7745 (RZ/G1E) SCIFA compatible UART. + - "renesas,scifb-r8a7745" for R8A7745 (RZ/G1E) SCIFB compatible UART. + - "renesas,hscif-r8a7745" for R8A7745 (RZ/G1E) HSCIF compatible UART. - "renesas,scif-r8a7778" for R8A7778 (R-Car M1) SCIF compatible UART. - "renesas,scif-r8a7779" for R8A7779 (R-Car H1) SCIF compatible UART. - "renesas,scif-r8a7790" for R8A7790 (R-Car H2) SCIF compatible UART. diff --git a/Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt b/Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt new file mode 100644 index 000000000000..5b9b38f578bb --- /dev/null +++ b/Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt @@ -0,0 +1,88 @@ +Devicetree bindings for the Axentia TSE-850 audio complex + +Required properties: + - compatible: "axentia,tse850-pcm5142" + - axentia,ssc-controller: The phandle of the atmel SSC controller used as + cpu dai. + - axentia,audio-codec: The phandle of the PCM5142 codec. + - axentia,add-gpios: gpio specifier that controls the mixer. + - axentia,loop1-gpios: gpio specifier that controls loop relays on channel 1. + - axentia,loop2-gpios: gpio specifier that controls loop relays on channel 2. + - axentia,ana-supply: Regulator that supplies the output amplifier. Must + support voltages in the 2V - 20V range, in 1V steps. + +The schematics explaining the gpios are as follows: + + loop1 relays + IN1 +---o +------------+ o---+ OUT1 + \ / + + + + | / | + +--o +--. | + | add | | + | V | + | .---. | + DAC +----------->|Sum|---+ + | '---' | + | | + + + + + IN2 +---o--+------------+--o---+ OUT2 + loop2 relays + +The 'loop1' gpio pin controlls two relays, which are either in loop position, +meaning that input and output are directly connected, or they are in mixer +position, meaning that the signal is passed through the 'Sum' mixer. Similarly +for 'loop2'. + +In the above, the 'loop1' relays are inactive, thus feeding IN1 to the mixer +(if 'add' is active) and feeding the mixer output to OUT1. The 'loop2' relays +are active, short-cutting the TSE-850 from channel 2. IN1, IN2, OUT1 and OUT2 +are TSE-850 connectors and DAC is the PCB name of the (filtered) output from +the PCM5142 codec. + +Example: + + &i2c { + codec: pcm5142@4c { + compatible = "ti,pcm5142"; + + reg = <0x4c>; + + AVDD-supply = <®_3v3>; + DVDD-supply = <®_3v3>; + CPVDD-supply = <®_3v3>; + + clocks = <&sck>; + + pll-in = <3>; + pll-out = <6>; + }; + }; + + ana: ana-reg { + compatible = "pwm-regulator"; + + regulator-name = "ANA"; + + pwms = <&pwm0 2 1000 PWM_POLARITY_INVERTED>; + pwm-dutycycle-unit = <1000>; + pwm-dutycycle-range = <100 1000>; + + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <20000000>; + regulator-ramp-delay = <1000>; + }; + + sound { + compatible = "axentia,tse850-pcm5142"; + + axentia,ssc-controller = <&ssc0>; + axentia,audio-codec = <&codec>; + + axentia,add-gpios = <&pioA 8 GPIO_ACTIVE_LOW>; + axentia,loop1-gpios = <&pioA 10 GPIO_ACTIVE_LOW>; + axentia,loop2-gpios = <&pioA 11 GPIO_ACTIVE_LOW>; + + axentia,ana-supply = <&ana>; + }; diff --git a/Documentation/devicetree/bindings/sound/cs35l34.txt b/Documentation/devicetree/bindings/sound/cs35l34.txt new file mode 100644 index 000000000000..b218ead2e68e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs35l34.txt @@ -0,0 +1,64 @@ +CS35L34 Speaker Amplifier + +Required properties: + + - compatible : "cirrus,cs35l34" + + - reg : the I2C address of the device for I2C. + + - VA-supply, VP-supply : power supplies for the device, + as covered in + Documentation/devicetree/bindings/regulator/regulator.txt. + + - cirrus,boost-vtge-millivolt : Boost Voltage Value. Configures the boost + converter's output voltage in mV. The range is from VP to 8V with + increments of 100mV. + + - cirrus,boost-nanohenry: Inductor value for boost converter. The value is + in nH and they can be values of 1000nH, 1100nH, 1200nH, 1500nH, and 2200nH. + +Optional properties: + + - reset-gpios: GPIO used to reset the amplifier. + + - interrupt-parent : Specifies the phandle of the interrupt controller to + which the IRQs from CS35L34 are delivered to. + - interrupts : IRQ line info CS35L34. + (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + for further information relating to interrupt properties) + + - cirrus,boost-peak-milliamp : Boost converter peak current limit in mA. The + range starts at 1200mA and goes to a maximum of 3840mA with increments of + 80mA. The default value is 2480mA. + + - cirrus,i2s-sdinloc : ADSP SDIN I2S channel location. Indicates whether the + received mono data is in the left or right portion of the I2S frame + according to the AD0 pin or directly via this configuration. + 0x0 (Default) = Selected by AD0 input (if AD0 = LOW, use left channel), + 0x2 = Left, + 0x1 = Selected by the inversion of the AD0 input (if AD0 = LOW, use right + channel), + 0x3 = Right. + + - cirrus,gain-zc-disable: Boolean property. If set, the gain change will take + effect without waiting for a zero cross. + + - cirrus,tdm-rising-edge: Boolean property. If set, data is on the rising edge of + SCLK. Otherwise, data is on the falling edge of SCLK. + + +Example: + +cs35l34: cs35l34@40 { + compatible = "cirrus,cs35l34"; + reg = <0x40>; + + interrupt-parent = <&gpio8>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + + reset-gpios = <&gpio 10 0>; + + cirrus,boost-vtge-milltvolt = <8000>; /* 8V */ + cirrus,boost-ind-nanohenry = <1000>; /* 1uH */ + cirrus,boost-peak-milliamp = <3000>; /* 3A */ +}; diff --git a/Documentation/devicetree/bindings/sound/cs42l42.txt b/Documentation/devicetree/bindings/sound/cs42l42.txt new file mode 100644 index 000000000000..9a2c5e2423d5 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs42l42.txt @@ -0,0 +1,110 @@ +CS42L42 audio CODEC + +Required properties: + + - compatible : "cirrus,cs42l42" + + - reg : the I2C address of the device for I2C. + + - VP-supply, VCP-supply, VD_FILT-supply, VL-supply, VA-supply : + power supplies for the device, as covered in + Documentation/devicetree/bindings/regulator/regulator.txt. + +Optional properties: + + - reset-gpios : a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the codec starts. + + - interrupt-parent : Specifies the phandle of the interrupt controller to + which the IRQs from CS42L42 are delivered to. + + - interrupts : IRQ line info CS42L42. + (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + for further information relating to interrupt properties) + + - cirrus,ts-inv : Boolean property. For jacks that invert the tip sense + polarity. Normal jacks will short tip sense pin to HS1 when headphones are + plugged in and leave tip sense floating when not plugged in. Inverting jacks + short tip sense when unplugged and float when plugged in. + + 0 = (Default) Non-inverted + 1 = Inverted + + - cirrus,ts-dbnc-rise : Debounce the rising edge of TIP_SENSE_PLUG. With no + debounce, the tip sense pin might be noisy on a plug event. + + 0 - 0ms, + 1 - 125ms, + 2 - 250ms, + 3 - 500ms, + 4 - 750ms, + 5 - (Default) 1s, + 6 - 1.25s, + 7 - 1.5s, + + - cirrus,ts-dbnc-fall : Debounce the falling edge of TIP_SENSE_UNPLUG. + With no debounce, the tip sense pin might be noisy on an unplug event. + + 0 - 0ms, + 1 - 125ms, + 2 - 250ms, + 3 - 500ms, + 4 - 750ms, + 5 - (Default) 1s, + 6 - 1.25s, + 7 - 1.5s, + + - cirrus,btn-det-init-dbnce : This sets how long the driver sleeps after + enabling button detection interrupts. After auto-detection and before + servicing button interrupts, the HS bias needs time to settle. If you + don't wait, there is possibility for erroneous button interrupt. + + 0ms - 200ms, + Default = 100ms + + - cirrus,btn-det-event-dbnce : This sets how long the driver delays after + receiving a button press interrupt. With level detect interrupts, you want + to wait a small amount of time to make sure the button press is making a + clean connection with the bias resistors. + + 0ms - 20ms, + Default = 10ms + + - cirrus,bias-lvls : For a level-detect headset button scheme, each button + will bias the mic pin to a certain voltage. To determine which button was + pressed, the driver will compare this biased voltage to sequential, + decreasing voltages and will stop when a comparator is tripped, + indicating a comparator voltage < bias voltage. This value represents a + percentage of the internally generated HS bias voltage. For different + hardware setups, a designer might want to tweak this. This is an array of + descending values for the comparator voltage. + + Array of 4 values + Each 0-63 + < x1 x2 x3 x4 > + Default = < 15 8 4 1> + + +Example: + +cs42l42: cs42l42@48 { + compatible = "cirrus,cs42l42"; + reg = <0x48>; + VA-supply = <&dummy_vreg>; + VP-supply = <&dummy_vreg>; + VCP-supply = <&dummy_vreg>; + VD_FILT-supply = <&dummy_vreg>; + VL-supply = <&dummy_vreg>; + + reset-gpios = <&axi_gpio_0 1 0>; + interrupt-parent = <&gpio0>; + interrupts = <55 8> + + cirrus,ts-inv = <0x00>; + cirrus,ts-dbnc-rise = <0x05>; + cirrus,ts-dbnc-fall = <0x00>; + cirrus,btn-det-init-dbnce = <100>; + cirrus,btn-det-event-dbnce = <10>; + cirrus,bias-lvls = <0x0F 0x08 0x04 0x01>; + cirrus,hs-bias-ramp-rate = <0x02>; +};
\ No newline at end of file diff --git a/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt b/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt index 55b53e1fd72c..e0b6165c9cfc 100644 --- a/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt +++ b/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt @@ -43,7 +43,7 @@ mcbsp0: mcbsp@1d10000 { <0x00310000 0x1000>; reg-names = "mpu", "dat"; interrupts = <97 98>; - interrupts-names = "rx", "tx"; + interrupt-names = "rx", "tx"; dmas = <&edma0 3 1 &edma0 2 1>; dma-names = "tx", "rx"; diff --git a/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt b/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt index fd40c852d7c7..462b04e8209f 100644 --- a/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt +++ b/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt @@ -12,7 +12,7 @@ Required properties: Optional properties: - ti,dmic: phandle for the OMAP dmic node if the machine have it connected -- ti,jack_detection: Need to be present if the board capable to detect jack +- ti,jack-detection: Need to be present if the board capable to detect jack insertion, removal. Available audio endpoints for the audio-routing table: diff --git a/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt b/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt index d9d8635ff94c..6a4aadc4ce06 100644 --- a/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt +++ b/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt @@ -44,8 +44,7 @@ Required dai-link subnodes: Required CPU/CODEC subnodes properties: -link-name : Name of the dai link. --sound-dai : phandle and port of CPU/CODEC --capture-dai : phandle and port of CPU/CODEC +-sound-dai : phandle/s and port of CPU/CODEC Example: @@ -73,7 +72,7 @@ sound: sound { sound-dai = <&lpass MI2S_PRIMARY>; }; codec { - sound-dai = <&wcd_codec 0>; + sound-dai = <&lpass_codec 0>, <&wcd_codec 0>; }; }; diff --git a/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt new file mode 100644 index 000000000000..ccb401cfef9d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt @@ -0,0 +1,85 @@ +msm8916 analog audio CODEC + +Bindings for codec Analog IP which is integrated in pmic pm8916, + +## Bindings for codec core on pmic: + +Required properties + - compatible = "qcom,pm8916-wcd-analog-codec"; + - reg: represents the slave base address provided to the peripheral. + - interrupt-parent : The parent interrupt controller. + - interrupts: List of interrupts in given SPMI peripheral. + - interrupt-names: Names specified to above list of interrupts in same + order. List of supported interrupt names are: + "cdc_spk_cnp_int" - Speaker click and pop interrupt. + "cdc_spk_clip_int" - Speaker clip interrupt. + "cdc_spk_ocp_int" - Speaker over current protect interrupt. + "mbhc_ins_rem_det1" - jack insert removal detect interrupt 1. + "mbhc_but_rel_det" - button release interrupt. + "mbhc_but_press_det" - button press event + "mbhc_ins_rem_det" - jack insert removal detect interrupt. + "mbhc_switch_int" - multi button headset interrupt. + "cdc_ear_ocp_int" - Earphone over current protect interrupt. + "cdc_hphr_ocp_int" - Headphone R over current protect interrupt. + "cdc_hphl_ocp_det" - Headphone L over current protect interrupt. + "cdc_ear_cnp_int" - earphone cnp interrupt. + "cdc_hphr_cnp_int" - hphr click and pop interrupt. + "cdc_hphl_cnp_int" - hphl click and pop interrupt. + + - clocks: Handle to mclk. + - clock-names: should be "mclk" + - vdd-cdc-io-supply: phandle to VDD_CDC_IO regulator DT node. + - vdd-cdc-tx-rx-cx-supply: phandle to VDD_CDC_TX/RX/CX regulator DT node. + - vdd-micbias-supply: phandle of VDD_MICBIAS supply's regulator DT node. + +Optional Properties: +- qcom,micbias1-ext-cap: boolean, present if micbias1 has external capacitor + connected. +- qcom,micbias2-ext-cap: boolean, present if micbias2 has external capacitor + connected. + +Example: + +spmi_bus { + ... + audio-codec@f000{ + compatible = "qcom,pm8916-wcd-analog-codec"; + reg = <0xf000 0x200>; + reg-names = "pmic-codec-core"; + clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>; + clock-names = "mclk"; + interrupt-parent = <&spmi_bus>; + interrupts = <0x1 0xf0 0x0 IRQ_TYPE_NONE>, + <0x1 0xf0 0x1 IRQ_TYPE_NONE>, + <0x1 0xf0 0x2 IRQ_TYPE_NONE>, + <0x1 0xf0 0x3 IRQ_TYPE_NONE>, + <0x1 0xf0 0x4 IRQ_TYPE_NONE>, + <0x1 0xf0 0x5 IRQ_TYPE_NONE>, + <0x1 0xf0 0x6 IRQ_TYPE_NONE>, + <0x1 0xf0 0x7 IRQ_TYPE_NONE>, + <0x1 0xf1 0x0 IRQ_TYPE_NONE>, + <0x1 0xf1 0x1 IRQ_TYPE_NONE>, + <0x1 0xf1 0x2 IRQ_TYPE_NONE>, + <0x1 0xf1 0x3 IRQ_TYPE_NONE>, + <0x1 0xf1 0x4 IRQ_TYPE_NONE>, + <0x1 0xf1 0x5 IRQ_TYPE_NONE>; + interrupt-names = "cdc_spk_cnp_int", + "cdc_spk_clip_int", + "cdc_spk_ocp_int", + "mbhc_ins_rem_det1", + "mbhc_but_rel_det", + "mbhc_but_press_det", + "mbhc_ins_rem_det", + "mbhc_switch_int", + "cdc_ear_ocp_int", + "cdc_hphr_ocp_int", + "cdc_hphl_ocp_det", + "cdc_ear_cnp_int", + "cdc_hphr_cnp_int", + "cdc_hphl_cnp_int"; + VDD-CDC-IO-supply = <&pm8916_l5>; + VDD-CDC-TX-RX-CX-supply = <&pm8916_l5>; + VDD-MICBIAS-supply = <&pm8916_l13>; + #sound-dai-cells = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-digital.txt b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-digital.txt new file mode 100644 index 000000000000..1c8e4cb25176 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-digital.txt @@ -0,0 +1,20 @@ +msm8916 digital audio CODEC + +## Bindings for codec core in lpass: + +Required properties + - compatible = "qcom,msm8916-wcd-digital-codec"; + - reg: address space for lpass codec. + - clocks: Handle to mclk and ahbclk + - clock-names: should be "mclk", "ahbix-clk". + +Example: + +audio-codec@771c000{ + compatible = "qcom,msm8916-wcd-digital-codec"; + reg = <0x0771c000 0x400>; + clocks = <&gcc GCC_ULTAUDIO_AHBFABRIC_IXFABRIC_CLK>, + <&gcc GCC_CODEC_DIGCODEC_CLK>; + clock-names = "ahbix-clk", "mclk"; + #sound-dai-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/sound/rt5514.txt b/Documentation/devicetree/bindings/sound/rt5514.txt index 9cabfc18cb57..929ca6756b02 100644 --- a/Documentation/devicetree/bindings/sound/rt5514.txt +++ b/Documentation/devicetree/bindings/sound/rt5514.txt @@ -13,6 +13,9 @@ Optional properties: - clocks: The phandle of the master clock to the CODEC - clock-names: Should be "mclk" +- realtek,dmic-init-delay-ms + Set the DMIC initial delay (ms) to wait it ready. + Pins on the device (for linking into audio routes) for RT5514: * DMIC1L diff --git a/Documentation/devicetree/bindings/sound/rt5663.txt b/Documentation/devicetree/bindings/sound/rt5663.txt index 7d3c974c6e2e..70eaeaed2b18 100644 --- a/Documentation/devicetree/bindings/sound/rt5663.txt +++ b/Documentation/devicetree/bindings/sound/rt5663.txt @@ -1,10 +1,10 @@ -RT5663/RT5668 audio CODEC +RT5663 audio CODEC This device supports I2C only. Required properties: -- compatible : One of "realtek,rt5663" or "realtek,rt5668". +- compatible : "realtek,rt5663". - reg : The I2C address of the device. @@ -12,7 +12,7 @@ Required properties: Optional properties: -Pins on the device (for linking into audio routes) for RT5663/RT5668: +Pins on the device (for linking into audio routes) for RT5663: * IN1P * IN1N diff --git a/Documentation/devicetree/bindings/sound/rt5665.txt b/Documentation/devicetree/bindings/sound/rt5665.txt new file mode 100755 index 000000000000..419c89219681 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5665.txt @@ -0,0 +1,68 @@ +RT5665/RT5666/RT5668 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : One of "realtek,rt5665", "realtek,rt5666" or "realtek,rt5668". + +- reg : The I2C address of the device. + +- interrupts : The CODEC's interrupt output. + +Optional properties: + +- realtek,in1-differential +- realtek,in2-differential +- realtek,in3-differential +- realtek,in4-differential + Boolean. Indicate MIC1/2/3/4 input are differential, rather than single-ended. + +- realtek,dmic1-data-pin + 0: dmic1 is not used + 1: using GPIO4 pin as dmic1 data pin + 2: using IN2N pin as dmic2 data pin + +- realtek,dmic2-data-pin + 0: dmic2 is not used + 1: using GPIO5 pin as dmic2 data pin + 2: using IN2P pin as dmic2 data pin + +- realtek,jd-src + 0: No JD is used + 1: using JD1 as JD source + +- realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin. + +Pins on the device (for linking into audio routes) for RT5659/RT5658: + + * DMIC L1 + * DMIC R1 + * DMIC L2 + * DMIC R2 + * IN1P + * IN1N + * IN2P + * IN2N + * IN3P + * IN3N + * IN4P + * IN4N + * HPOL + * HPOR + * LOUTL + * LOUTR + * MONOOUT + * PDML + * PDMR + +Example: + +rt5659 { + compatible = "realtek,rt5665"; + reg = <0x1b>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(W, 3) GPIO_ACTIVE_HIGH>; + realtek,ldo1-en-gpios = + <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/sound/samsung,tm2-audio.txt b/Documentation/devicetree/bindings/sound/samsung,tm2-audio.txt new file mode 100644 index 000000000000..94442e5673b3 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/samsung,tm2-audio.txt @@ -0,0 +1,38 @@ +Samsung Exynos5433 TM2(E) audio complex with WM5110 codec + +Required properties: + + - compatible : "samsung,tm2-audio" + - model : the user-visible name of this sound complex + - audio-codec : the phandle of the wm5110 audio codec node, + as described in ../mfd/arizona.txt + - i2s-controller : the phandle of the I2S controller + - audio-amplifier : the phandle of the MAX98504 amplifier + - samsung,audio-routing : a list of the connections between audio components; + each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source; valid names for sources and sinks are the + WM5110's and MAX98504's pins and the jacks on the + board: HP, SPK, Main Mic, Sub Mic, Third Mic, + Headset Mic + - mic-bias-gpios : GPIO pin that enables the Main Mic bias regulator + + +Example: + +sound { + compatible = "samsung,tm2-audio"; + audio-codec = <&wm5110>; + i2s-controller = <&i2s0>; + audio-amplifier = <&max98504>; + mic-bias-gpios = <&gpr3 2 0>; + model = "wm5110"; + samsung,audio-routing = + "HP", "HPOUT1L", + "HP", "HPOUT1R", + "SPK", "SPKOUT", + "SPKOUT", "HPOUT2L", + "SPKOUT", "HPOUT2R", + "Main Mic", "MICBIAS2", + "IN1R", "Main Mic"; +}; diff --git a/Documentation/devicetree/bindings/sound/sun4i-codec.txt b/Documentation/devicetree/bindings/sound/sun4i-codec.txt index 0dce690f78f5..3033bd8aab0f 100644 --- a/Documentation/devicetree/bindings/sound/sun4i-codec.txt +++ b/Documentation/devicetree/bindings/sound/sun4i-codec.txt @@ -1,8 +1,12 @@ * Allwinner A10 Codec Required properties: -- compatible: must be either "allwinner,sun4i-a10-codec" or - "allwinner,sun7i-a20-codec" +- compatible: must be one of the following compatibles: + - "allwinner,sun4i-a10-codec" + - "allwinner,sun6i-a31-codec" + - "allwinner,sun7i-a20-codec" + - "allwinner,sun8i-a23-codec" + - "allwinner,sun8i-h3-codec" - reg: must contain the registers location and length - interrupts: must contain the codec interrupt - dmas: DMA channels for tx and rx dma. See the DMA client binding, @@ -17,6 +21,43 @@ Required properties: Optional properties: - allwinner,pa-gpios: gpio to enable external amplifier +Required properties for the following compatibles: + - "allwinner,sun6i-a31-codec" + - "allwinner,sun8i-a23-codec" + - "allwinner,sun8i-h3-codec" +- resets: phandle to the reset control for this device +- allwinner,audio-routing: A list of the connections between audio components. + Each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source. Valid names include: + + Audio pins on the SoC: + "HP" + "HPCOM" + "LINEIN" + "LINEOUT" (not on sun8i-a23) + "MIC1" + "MIC2" + "MIC3" (sun6i-a31 only) + + Microphone biases from the SoC: + "HBIAS" + "MBIAS" + + Board connectors: + "Headphone" + "Headset Mic" + "Line In" + "Line Out" + "Mic" + "Speaker" + +Required properties for the following compatibles: + - "allwinner,sun8i-a23-codec" + - "allwinner,sun8i-h3-codec" +- allwinner,codec-analog-controls: A phandle to the codec analog controls + block in the PRCM. + Example: codec: codec@01c22c00 { #sound-dai-cells = <0>; @@ -28,3 +69,23 @@ codec: codec@01c22c00 { dmas = <&dma 0 19>, <&dma 0 19>; dma-names = "rx", "tx"; }; + +codec: codec@01c22c00 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun6i-a31-codec"; + reg = <0x01c22c00 0x98>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_APB1_CODEC>, <&ccu CLK_CODEC>; + clock-names = "apb", "codec"; + resets = <&ccu RST_APB1_CODEC>; + dmas = <&dma 15>, <&dma 15>; + dma-names = "rx", "tx"; + allwinner,audio-routing = + "Headphone", "HP", + "Speaker", "LINEOUT", + "LINEIN", "Line In", + "MIC1", "MBIAS", + "MIC1", "Mic", + "MIC2", "HBIAS", + "MIC2", "Headset Mic"; +}; diff --git a/Documentation/devicetree/bindings/sound/sun8i-codec-analog.txt b/Documentation/devicetree/bindings/sound/sun8i-codec-analog.txt new file mode 100644 index 000000000000..779b735781ba --- /dev/null +++ b/Documentation/devicetree/bindings/sound/sun8i-codec-analog.txt @@ -0,0 +1,16 @@ +* Allwinner Codec Analog Controls + +Required properties: +- compatible: must be one of the following compatibles: + - "allwinner,sun8i-a23-codec-analog" + - "allwinner,sun8i-h3-codec-analog" + +Required properties if not a sub-node of the PRCM node: +- reg: must contain the registers location and length + +Example: +prcm: prcm@01f01400 { + codec_analog: codec-analog { + compatible = "allwinner,sun8i-a23-codec-analog"; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt b/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt index 9340d2ddcc54..6fbba562eaa7 100644 --- a/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt +++ b/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt @@ -12,6 +12,7 @@ Required properties: "ti,tlv320aic3120" - TLV320AIC3120 (mono speaker amp, MiniDSP) "ti,tlv320aic3111" - TLV320AIC3111 (stereo speaker amp, MiniDSP) "ti,tlv320dac3100" - TLV320DAC3100 (no ADC, mono speaker amp, no MiniDSP) + "ti,tlv320dac3101" - TLV320DAC3101 (no ADC, stereo speaker amp, no MiniDSP) - reg - <int> - I2C slave address - HPVDD-supply, SPRVDD-supply, SPLVDD-supply, AVDD-supply, IOVDD-supply, diff --git a/Documentation/devicetree/bindings/sound/wm8580.txt b/Documentation/devicetree/bindings/sound/wm8580.txt index 7d9821f348da..78fce9b14954 100644 --- a/Documentation/devicetree/bindings/sound/wm8580.txt +++ b/Documentation/devicetree/bindings/sound/wm8580.txt @@ -1,10 +1,10 @@ -WM8580 audio CODEC +WM8580 and WM8581 audio CODEC This device supports I2C only. Required properties: - - compatible : "wlf,wm8580" + - compatible : "wlf,wm8580", "wlf,wm8581" - reg : the I2C address of the device. diff --git a/Documentation/devicetree/bindings/timer/jcore,pit.txt b/Documentation/devicetree/bindings/timer/jcore,pit.txt new file mode 100644 index 000000000000..af5dd35469d7 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/jcore,pit.txt @@ -0,0 +1,24 @@ +J-Core Programmable Interval Timer and Clocksource + +Required properties: + +- compatible: Must be "jcore,pit". + +- reg: Memory region(s) for timer/clocksource registers. For SMP, + there should be one region per cpu, indexed by the sequential, + zero-based hardware cpu number. + +- interrupts: An interrupt to assign for the timer. The actual pit + core is integrated with the aic and allows the timer interrupt + assignment to be programmed by software, but this property is + required in order to reserve an interrupt number that doesn't + conflict with other devices. + + +Example: + +timer@200 { + compatible = "jcore,pit"; + reg = < 0x200 0x30 0x500 0x30 >; + interrupts = < 0x48 >; +}; diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt index 455f2c310a1b..2c30a5479069 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.txt +++ b/Documentation/devicetree/bindings/usb/dwc2.txt @@ -28,10 +28,7 @@ Refer to phy/phy-bindings.txt for generic phy consumer properties - g-use-dma: enable dma usage in gadget driver. - g-rx-fifo-size: size of rx fifo size in gadget mode. - g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget mode. - -Deprecated properties: -- g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) - in gadget mode. +- g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode. Example: |