diff options
Diffstat (limited to '')
61 files changed, 1180 insertions, 169 deletions
diff --git a/Documentation/devicetree/bindings/Makefile b/Documentation/devicetree/bindings/Makefile index 6e5cef0ed6fb..50daa0b3b032 100644 --- a/Documentation/devicetree/bindings/Makefile +++ b/Documentation/devicetree/bindings/Makefile @@ -17,7 +17,11 @@ extra-y += $(DT_TMP_SCHEMA) quiet_cmd_mk_schema = SCHEMA $@ cmd_mk_schema = $(DT_MK_SCHEMA) $(DT_MK_SCHEMA_FLAGS) -o $@ $(filter-out FORCE, $^) -DT_DOCS = $(shell cd $(srctree)/$(src) && find * -name '*.yaml') +DT_DOCS = $(shell \ + cd $(srctree)/$(src) && \ + find * \( -name '*.yaml' ! -name $(DT_TMP_SCHEMA) \) \ + ) + DT_SCHEMA_FILES ?= $(addprefix $(src)/,$(DT_DOCS)) extra-y += $(patsubst $(src)/%.yaml,%.example.dts, $(DT_SCHEMA_FILES)) diff --git a/Documentation/devicetree/bindings/arm/cpu-capacity.txt b/Documentation/devicetree/bindings/arm/cpu-capacity.txt index 84262cdb8d29..96fa46cb133c 100644 --- a/Documentation/devicetree/bindings/arm/cpu-capacity.txt +++ b/Documentation/devicetree/bindings/arm/cpu-capacity.txt @@ -235,4 +235,4 @@ cpus { =========================================== [1] ARM Linux Kernel documentation - CPUs bindings - Documentation/devicetree/bindings/arm/cpus.txt + Documentation/devicetree/bindings/arm/cpus.yaml diff --git a/Documentation/devicetree/bindings/arm/idle-states.txt b/Documentation/devicetree/bindings/arm/idle-states.txt index 8f0937db55c5..45730ba60af5 100644 --- a/Documentation/devicetree/bindings/arm/idle-states.txt +++ b/Documentation/devicetree/bindings/arm/idle-states.txt @@ -684,7 +684,7 @@ cpus { =========================================== [1] ARM Linux Kernel documentation - CPUs bindings - Documentation/devicetree/bindings/arm/cpus.txt + Documentation/devicetree/bindings/arm/cpus.yaml [2] ARM Linux Kernel documentation - PSCI bindings Documentation/devicetree/bindings/arm/psci.txt diff --git a/Documentation/devicetree/bindings/arm/sp810.txt b/Documentation/devicetree/bindings/arm/sp810.txt index 1b2ab1ff5587..46652bf65147 100644 --- a/Documentation/devicetree/bindings/arm/sp810.txt +++ b/Documentation/devicetree/bindings/arm/sp810.txt @@ -4,7 +4,7 @@ SP810 System Controller Required properties: - compatible: standard compatible string for a Primecell peripheral, - see Documentation/devicetree/bindings/arm/primecell.txt + see Documentation/devicetree/bindings/arm/primecell.yaml for more details should be: "arm,sp810", "arm,primecell" diff --git a/Documentation/devicetree/bindings/arm/topology.txt b/Documentation/devicetree/bindings/arm/topology.txt index de9eb0486630..b0d80c0fb265 100644 --- a/Documentation/devicetree/bindings/arm/topology.txt +++ b/Documentation/devicetree/bindings/arm/topology.txt @@ -472,4 +472,4 @@ cpus { =============================================================================== [1] ARM Linux kernel documentation - Documentation/devicetree/bindings/arm/cpus.txt + Documentation/devicetree/bindings/arm/cpus.yaml diff --git a/Documentation/devicetree/bindings/clock/marvell,mmp2.txt b/Documentation/devicetree/bindings/clock/marvell,mmp2.txt index af376a01f2b7..23b52dc02266 100644 --- a/Documentation/devicetree/bindings/clock/marvell,mmp2.txt +++ b/Documentation/devicetree/bindings/clock/marvell,mmp2.txt @@ -18,4 +18,4 @@ Required Properties: Each clock is assigned an identifier and client nodes use this identifier to specify the clock which they consume. -All these identifier could be found in <dt-bindings/clock/marvell-mmp2.h>. +All these identifiers could be found in <dt-bindings/clock/marvell,mmp2.h>. diff --git a/Documentation/devicetree/bindings/crypto/samsung-slimsss.txt b/Documentation/devicetree/bindings/crypto/samsung-slimsss.txt new file mode 100644 index 000000000000..7ec9a5a7727a --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/samsung-slimsss.txt @@ -0,0 +1,19 @@ +Samsung SoC SlimSSS (Slim Security SubSystem) module + +The SlimSSS module in Exynos5433 SoC supports the following: +-- Feeder (FeedCtrl) +-- Advanced Encryption Standard (AES) with ECB,CBC,CTR,XTS and (CBC/XTS)/CTS +-- SHA-1/SHA-256 and (SHA-1/SHA-256)/HMAC + +Required properties: + +- compatible : Should contain entry for slimSSS version: + - "samsung,exynos5433-slim-sss" for Exynos5433 SoC. +- reg : Offset and length of the register set for the module +- interrupts : interrupt specifiers of SlimSSS module interrupts (one feed + control interrupt). + +- clocks : list of clock phandle and specifier pairs for all clocks listed in + clock-names property. +- clock-names : list of device clock input names; should contain "pclk" and + "aclk" for slim-sss in Exynos5433. diff --git a/Documentation/devicetree/bindings/display/arm,pl11x.txt b/Documentation/devicetree/bindings/display/arm,pl11x.txt index ef89ab46b2c9..572fa2773ec4 100644 --- a/Documentation/devicetree/bindings/display/arm,pl11x.txt +++ b/Documentation/devicetree/bindings/display/arm,pl11x.txt @@ -1,6 +1,6 @@ * ARM PrimeCell Color LCD Controller PL110/PL111 -See also Documentation/devicetree/bindings/arm/primecell.txt +See also Documentation/devicetree/bindings/arm/primecell.yaml Required properties: diff --git a/Documentation/devicetree/bindings/display/msm/gpu.txt b/Documentation/devicetree/bindings/display/msm/gpu.txt index ac8df3b871f9..f8759145ce1a 100644 --- a/Documentation/devicetree/bindings/display/msm/gpu.txt +++ b/Documentation/devicetree/bindings/display/msm/gpu.txt @@ -27,7 +27,6 @@ Example: reg = <0x04300000 0x20000>; reg-names = "kgsl_3d0_reg_memory"; interrupts = <GIC_SPI 80 0>; - interrupt-names = "kgsl_3d0_irq"; clock-names = "core", "iface", diff --git a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt index 38ca2201e8ae..2e097b57f170 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt @@ -14,8 +14,6 @@ Required properties: "marvell,armada-8k-gpio" should be used for the Armada 7K and 8K SoCs (either from AP or CP), see - Documentation/devicetree/bindings/arm/marvell/cp110-system-controller0.txt - and Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt for specific details about the offset property. diff --git a/Documentation/devicetree/bindings/hwmon/ad741x.txt b/Documentation/devicetree/bindings/hwmon/ad741x.txt new file mode 100644 index 000000000000..9102152c8410 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/ad741x.txt @@ -0,0 +1,15 @@ +* AD7416/AD7417/AD7418 Temperature Sensor Device Tree Bindings + +Required properties: +- compatible: one of + "adi,ad7416" + "adi,ad7417" + "adi,ad7418" +- reg: I2C address + +Example: + +hwmon@28 { + compatible = "adi,ad7418"; + reg = <0x28>; +}; diff --git a/Documentation/devicetree/bindings/hwmon/dps650ab.txt b/Documentation/devicetree/bindings/hwmon/dps650ab.txt new file mode 100644 index 000000000000..76780e795899 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/dps650ab.txt @@ -0,0 +1,11 @@ +Bindings for Delta Electronics DPS-650-AB power supply + +Required properties: +- compatible : "delta,dps650ab" +- reg : I2C address, one of 0x58, 0x59. + +Example: + dps650ab@58 { + compatible = "delta,dps650ab"; + reg = <0x58>; + }; diff --git a/Documentation/devicetree/bindings/hwmon/hih6130.txt b/Documentation/devicetree/bindings/hwmon/hih6130.txt new file mode 100644 index 000000000000..2c43837af4c2 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/hih6130.txt @@ -0,0 +1,12 @@ +Honeywell Humidicon HIH-6130 humidity/temperature sensor +-------------------------------------------------------- + +Requires node properties: +- compatible : "honeywell,hi6130" +- reg : the I2C address of the device. This is 0x27. + +Example: + hih6130@27 { + compatible = "honeywell,hih6130"; + reg = <0x27>; + }; diff --git a/Documentation/devicetree/bindings/hwmon/ina3221.txt b/Documentation/devicetree/bindings/hwmon/ina3221.txt index a7b25caa2b8e..fa63b6171407 100644 --- a/Documentation/devicetree/bindings/hwmon/ina3221.txt +++ b/Documentation/devicetree/bindings/hwmon/ina3221.txt @@ -6,6 +6,16 @@ Texas Instruments INA3221 Device Tree Bindings - reg: I2C address Optional properties: + - ti,single-shot: This chip has two power modes: single-shot (chip takes one + measurement and then shuts itself down) and continuous ( + chip takes continuous measurements). The continuous mode is + more reliable and suitable for hardware monitor type device, + but the single-shot mode is more power-friendly and useful + for battery-powered device which cares power consumptions + while still needs some measurements occasionally. + If this property is present, the single-shot mode will be + used, instead of the default continuous one for monitoring. + = The node contains optional child nodes for three channels = = Each child node describes the information of input source = diff --git a/Documentation/devicetree/bindings/hwmon/lm75.txt b/Documentation/devicetree/bindings/hwmon/lm75.txt new file mode 100644 index 000000000000..12d8cf7cf592 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/lm75.txt @@ -0,0 +1,37 @@ +*LM75 hwmon sensor. + +Required properties: +- compatible: manufacturer and chip name, one of + "adi,adt75", + "dallas,ds1775", + "dallas,ds75", + "dallas,ds7505", + "gmt,g751", + "national,lm75", + "national,lm75a", + "national,lm75b", + "maxim,max6625", + "maxim,max6626", + "maxim,max31725", + "maxim,max31726", + "maxim,mcp980x", + "st,stds75", + "st,stlm75", + "microchip,tcn75", + "ti,tmp100", + "ti,tmp101", + "ti,tmp105", + "ti,tmp112", + "ti,tmp175", + "ti,tmp275", + "ti,tmp75", + "ti,tmp75c", + +- reg: I2C bus address of the device + +Example: + +sensor@48 { + compatible = "st,stlm75"; + reg = <0x48>; +}; diff --git a/Documentation/devicetree/bindings/hwmon/pwm-fan.txt b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt index c6d533202d3e..49ca5d83ed13 100644 --- a/Documentation/devicetree/bindings/hwmon/pwm-fan.txt +++ b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt @@ -6,6 +6,9 @@ Required properties: - cooling-levels : PWM duty cycle values in a range from 0 to 255 which correspond to thermal cooling states +Optional properties: +- fan-supply : phandle to the regulator that provides power to the fan + Example: fan0: pwm-fan { compatible = "pwm-fan"; diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt index b83bb8249074..a3be5298a5eb 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt @@ -78,7 +78,7 @@ Sub-nodes: PPI affinity can be expressed as a single "ppi-partitions" node, containing a set of sub-nodes, each with the following property: - affinity: Should be a list of phandles to CPU nodes (as described in -Documentation/devicetree/bindings/arm/cpus.txt). + Documentation/devicetree/bindings/arm/cpus.yaml). GICv3 has one or more Interrupt Translation Services (ITS) that are used to route Message Signalled Interrupts (MSI) to the CPUs. diff --git a/Documentation/devicetree/bindings/leds/common.txt b/Documentation/devicetree/bindings/leds/common.txt index aa1399814a2a..70876ac11367 100644 --- a/Documentation/devicetree/bindings/leds/common.txt +++ b/Documentation/devicetree/bindings/leds/common.txt @@ -37,6 +37,18 @@ Optional properties for child nodes: "ide-disk" - LED indicates IDE disk activity (deprecated), in new implementations use "disk-activity" "timer" - LED flashes at a fixed, configurable rate + "pattern" - LED alters the brightness for the specified duration with one + software timer (requires "led-pattern" property) + +- led-pattern : Array of integers with default pattern for certain triggers. + Each trigger may parse this property differently: + - one-shot : two numbers specifying delay on and delay off (in ms), + - timer : two numbers specifying delay on and delay off (in ms), + - pattern : the pattern is given by a series of tuples, of + brightness and duration (in ms). The exact format is + described in: + Documentation/devicetree/bindings/leds/leds-trigger-pattern.txt + - led-max-microamp : Maximum LED supply current in microamperes. This property can be made mandatory for the board configurations diff --git a/Documentation/devicetree/bindings/leds/leds-trigger-pattern.txt b/Documentation/devicetree/bindings/leds/leds-trigger-pattern.txt new file mode 100644 index 000000000000..d3696680bfc8 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-trigger-pattern.txt @@ -0,0 +1,49 @@ +* Pattern format for LED pattern trigger + +The pattern is given by a series of tuples, of brightness and duration (ms). +The LED is expected to traverse the series and each brightness value for the +specified duration. Duration of 0 means brightness should immediately change to +new value, and writing malformed pattern deactivates any active one. + +1. For gradual dimming, the dimming interval now is set as 50 milliseconds. So +the tuple with duration less than dimming interval (50ms) is treated as a step +change of brightness, i.e. the subsequent brightness will be applied without +adding intervening dimming intervals. + +The gradual dimming format of the software pattern values should be: +"brightness_1 duration_1 brightness_2 duration_2 brightness_3 duration_3 ...". +For example (using sysfs interface): + +echo 0 1000 255 2000 > pattern + +It will make the LED go gradually from zero-intensity to max (255) intensity in +1000 milliseconds, then back to zero intensity in 2000 milliseconds: + +LED brightness + ^ +255-| / \ / \ / + | / \ / \ / + | / \ / \ / + | / \ / \ / + 0-| / \/ \/ + +---0----1----2----3----4----5----6------------> time (s) + +2. To make the LED go instantly from one brightness value to another, we should +use zero-time lengths (the brightness must be same as the previous tuple's). So +the format should be: "brightness_1 duration_1 brightness_1 0 brightness_2 +duration_2 brightness_2 0 ...". +For example (using sysfs interface): + +echo 0 1000 0 0 255 2000 255 0 > pattern + +It will make the LED stay off for one second, then stay at max brightness for +two seconds: + +LED brightness + ^ +255-| +---------+ +---------+ + | | | | | + | | | | | + | | | | | + 0-| -----+ +----+ +---- + +---0----1----2----3----4----5----6------------> time (s) diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt index a4b056761eaa..d5f68ac78d15 100644 --- a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt +++ b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt @@ -23,6 +23,20 @@ Required properties: Optional properties: - clock-output-names : Should contain name for output clock. +- rohm,reset-snvs-powered : Transfer BD718x7 to SNVS state at reset. + +The BD718x7 supports two different HW states as reset target states. States +are called as SNVS and READY. At READY state all the PMIC power outputs go +down and OTP is reload. At the SNVS state all other logic and external +devices apart from the SNVS power domain are shut off. Please refer to NXP +i.MX8 documentation for further information regarding SNVS state. When a +reset is done via SNVS state the PMIC OTP data is not reload. This causes +power outputs that have been under SW control to stay down when reset has +switched power state to SNVS. If reset is done via READY state the power +outputs will be returned to HW control by OTP loading. Thus the reset +target state is set to READY by default. If SNVS state is used the boot +crucial regulators must have the regulator-always-on and regulator-boot-on +properties set in regulator node. Example: @@ -43,6 +57,7 @@ Example: #clock-cells = <0>; clocks = <&osc 0>; clock-output-names = "bd71837-32k-out"; + rohm,reset-snvs-powered; regulators { buck1: BUCK1 { @@ -50,8 +65,10 @@ Example: regulator-min-microvolt = <700000>; regulator-max-microvolt = <1300000>; regulator-boot-on; + regulator-always-on; regulator-ramp-delay = <1250>; }; + // [...] }; }; diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt index 9201a7d8d7b0..540c65ed9cba 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -15,6 +15,7 @@ Required properties: "fsl,imx6q-usdhc" "fsl,imx6sl-usdhc" "fsl,imx6sx-usdhc" + "fsl,imx6ull-usdhc" "fsl,imx7d-usdhc" "fsl,imx8qxp-usdhc" diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index f5a0923b34ca..cdbcfd3a4ff2 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -62,6 +62,8 @@ Optional properties: be referred to mmc-pwrseq-simple.txt. But now it's reused as a tunable delay waiting for I/O signalling and card power supply to be stable, regardless of whether pwrseq-simple is used. Default to 10ms if no available. +- supports-cqe : The presence of this property indicates that the corresponding + MMC host controller supports HW command queue feature. *NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line polarity properties, we have to fix the meaning of the "normal" and "inverted" diff --git a/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt index 32b4b4e41923..2cecdc71d94c 100644 --- a/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt @@ -39,12 +39,16 @@ sdhci@c8000200 { bus-width = <8>; }; -Optional properties for Tegra210 and Tegra186: +Optional properties for Tegra210, Tegra186 and Tegra194: - pinctrl-names, pinctrl-0, pinctrl-1 : Specify pad voltage configurations. Valid pinctrl-names are "sdmmc-3v3" and "sdmmc-1v8" for controllers supporting multiple voltage levels. The order of names should correspond to the pin configuration states in pinctrl-0 and pinctrl-1. +- pinctrl-names : "sdmmc-3v3-drv" and "sdmmc-1v8-drv" are applicable for + Tegra210 where pad config registers are in the pinmux register domain + for pull-up-strength and pull-down-strength values configuration when + using pads at 3V3 and 1V8 levels. - nvidia,only-1-8-v : The presence of this property indicates that the controller operates at a 1.8 V fixed I/O voltage. - nvidia,pad-autocal-pull-up-offset-3v3, diff --git a/Documentation/devicetree/bindings/mmc/ti-omap.txt b/Documentation/devicetree/bindings/mmc/ti-omap.txt index 8de579969763..02fd31cf361d 100644 --- a/Documentation/devicetree/bindings/mmc/ti-omap.txt +++ b/Documentation/devicetree/bindings/mmc/ti-omap.txt @@ -24,31 +24,3 @@ Examples: dmas = <&sdma 61 &sdma 62>; dma-names = "tx", "rx"; }; - -* TI MMC host controller for OMAP1 and 2420 - -The MMC Host Controller on TI OMAP1 and 2420 family provides -an interface for MMC, SD, and SDIO types of memory cards. - -This file documents differences between the core properties described -by mmc.txt and the properties used by the omap mmc driver. - -Note that this driver will not work with omap2430 or later omaps, -please see the omap hsmmc driver for the current omaps. - -Required properties: -- compatible: Must be "ti,omap2420-mmc", for OMAP2420 controllers -- ti,hwmods: For 2420, must be "msdi<n>", where n is controller - instance starting 1 - -Examples: - - msdi1: mmc@4809c000 { - compatible = "ti,omap2420-mmc"; - ti,hwmods = "msdi1"; - reg = <0x4809c000 0x80>; - interrupts = <83>; - dmas = <&sdma 61 &sdma 62>; - dma-names = "tx", "rx"; - }; - diff --git a/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt b/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt new file mode 100644 index 000000000000..3983c11e062c --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt @@ -0,0 +1,60 @@ +Amlogic NAND Flash Controller (NFC) for GXBB/GXL/AXG family SoCs + +This file documents the properties in addition to those available in +the MTD NAND bindings. + +Required properties: +- compatible : contains one of: + - "amlogic,meson-gxl-nfc" + - "amlogic,meson-axg-nfc" +- clocks : + A list of phandle + clock-specifier pairs for the clocks listed + in clock-names. + +- clock-names: Should contain the following: + "core" - NFC module gate clock + "device" - device clock from eMMC sub clock controller + "rx" - rx clock phase + "tx" - tx clock phase + +- amlogic,mmc-syscon : Required for NAND clocks, it's shared with SD/eMMC + controller port C + +Optional children nodes: +Children nodes represent the available nand chips. + +Other properties: +see Documentation/devicetree/bindings/mtd/nand.txt for generic bindings. + +Example demonstrate on AXG SoC: + + sd_emmc_c_clkc: mmc@7000 { + compatible = "amlogic,meson-axg-mmc-clkc", "syscon"; + reg = <0x0 0x7000 0x0 0x800>; + }; + + nand-controller@7800 { + compatible = "amlogic,meson-axg-nfc"; + reg = <0x0 0x7800 0x0 0x100>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>; + + clocks = <&clkc CLKID_SD_EMMC_C>, + <&sd_emmc_c_clkc CLKID_MMC_DIV>, + <&sd_emmc_c_clkc CLKID_MMC_PHASE_RX>, + <&sd_emmc_c_clkc CLKID_MMC_PHASE_TX>; + clock-names = "core", "device", "rx", "tx"; + amlogic,mmc-syscon = <&sd_emmc_c_clkc>; + + pinctrl-names = "default"; + pinctrl-0 = <&nand_pins>; + + nand@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + + nand-on-flash-bbt; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt index bb2075df9b38..4345c3a6f530 100644 --- a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt +++ b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt @@ -4,6 +4,7 @@ Required properties: - compatible : should be one of the following: Generic default - "cdns,qspi-nor". For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor". + For TI AM654 SoC - "ti,am654-ospi", "cdns,qspi-nor". - reg : Contains two entries, each of which is a tuple consisting of a physical address and length. The first entry is the address and length of the controller register set. The second entry is the diff --git a/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt b/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt index 56d3668e2c50..a12e3b5c495d 100644 --- a/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt +++ b/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt @@ -1,4 +1,4 @@ -* Serial NOR flash controller for MTK MT81xx (and similar) +* Serial NOR flash controller for MediaTek SoCs Required properties: - compatible: For mt8173, compatible should be "mediatek,mt8173-nor", @@ -10,6 +10,7 @@ Required properties: "mediatek,mt2712-nor", "mediatek,mt8173-nor" "mediatek,mt7622-nor", "mediatek,mt8173-nor" "mediatek,mt7623-nor", "mediatek,mt8173-nor" + "mediatek,mt7629-nor", "mediatek,mt8173-nor" "mediatek,mt8173-nor" - reg: physical base address and length of the controller's register - clocks: the phandle of the clocks needed by the nor controller diff --git a/Documentation/devicetree/bindings/mtd/stm32-fmc2-nand.txt b/Documentation/devicetree/bindings/mtd/stm32-fmc2-nand.txt new file mode 100644 index 000000000000..ad2bef826582 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/stm32-fmc2-nand.txt @@ -0,0 +1,61 @@ +STMicroelectronics Flexible Memory Controller 2 (FMC2) +NAND Interface + +Required properties: +- compatible: Should be one of: + * st,stm32mp15-fmc2 +- reg: NAND flash controller memory areas. + First region contains the register location. + Regions 2 to 4 respectively contain the data, command, + and address space for CS0. + Regions 5 to 7 contain the same areas for CS1. +- interrupts: The interrupt number +- pinctrl-0: Standard Pinctrl phandle (see: pinctrl/pinctrl-bindings.txt) +- clocks: The clock needed by the NAND flash controller + +Optional properties: +- resets: Reference to a reset controller asserting the FMC controller +- dmas: DMA specifiers (see: dma/stm32-mdma.txt) +- dma-names: Must be "tx", "rx" and "ecc" + +* NAND device bindings: + +Required properties: +- reg: describes the CS lines assigned to the NAND device. + +Optional properties: +- nand-on-flash-bbt: see nand.txt +- nand-ecc-strength: see nand.txt +- nand-ecc-step-size: see nand.txt + +The following ECC strength and step size are currently supported: + - nand-ecc-strength = <1>, nand-ecc-step-size = <512> (Hamming) + - nand-ecc-strength = <4>, nand-ecc-step-size = <512> (BCH4) + - nand-ecc-strength = <8>, nand-ecc-step-size = <512> (BCH8) (default) + +Example: + + fmc: nand-controller@58002000 { + compatible = "st,stm32mp15-fmc2"; + reg = <0x58002000 0x1000>, + <0x80000000 0x1000>, + <0x88010000 0x1000>, + <0x88020000 0x1000>, + <0x81000000 0x1000>, + <0x89010000 0x1000>, + <0x89020000 0x1000>; + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc FMC_K>; + resets = <&rcc FMC_R>; + pinctrl-names = "default"; + pinctrl-0 = <&fmc_pins_a>; + #address-cells = <1>; + #size-cells = <0>; + + nand@0 { + reg = <0>; + nand-on-flash-bbt; + #address-cells = <1>; + #size-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/btusb.txt b/Documentation/devicetree/bindings/net/btusb.txt index 37d67926dd6d..b1ad6ee68e90 100644 --- a/Documentation/devicetree/bindings/net/btusb.txt +++ b/Documentation/devicetree/bindings/net/btusb.txt @@ -9,6 +9,9 @@ Required properties: (more may be added later) are: "usb1286,204e" (Marvell 8997) + "usbcf3,e300" (Qualcomm QCA6174A) + "usb4ca,301a" (Qualcomm QCA6174A (Lite-On)) + Also, vendors that use btusb may have device additional properties, e.g: Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt diff --git a/Documentation/devicetree/bindings/net/dsa/ksz.txt b/Documentation/devicetree/bindings/net/dsa/ksz.txt index 0f407fb371ce..e7db7268fd0f 100644 --- a/Documentation/devicetree/bindings/net/dsa/ksz.txt +++ b/Documentation/devicetree/bindings/net/dsa/ksz.txt @@ -7,6 +7,11 @@ Required properties: of the following: - "microchip,ksz9477" - "microchip,ksz9897" + - "microchip,ksz9896" + - "microchip,ksz9567" + - "microchip,ksz8565" + - "microchip,ksz9893" + - "microchip,ksz9563" Optional properties: @@ -19,58 +24,96 @@ Examples: Ethernet switch connected via SPI to the host, CPU port wired to eth0: - eth0: ethernet@10001000 { - fixed-link { - speed = <1000>; - full-duplex; - }; - }; + eth0: ethernet@10001000 { + fixed-link { + speed = <1000>; + full-duplex; + }; + }; - spi1: spi@f8008000 { - pinctrl-0 = <&pinctrl_spi_ksz>; - cs-gpios = <&pioC 25 0>; - id = <1>; + spi1: spi@f8008000 { + pinctrl-0 = <&pinctrl_spi_ksz>; + cs-gpios = <&pioC 25 0>; + id = <1>; - ksz9477: ksz9477@0 { - compatible = "microchip,ksz9477"; - reg = <0>; + ksz9477: ksz9477@0 { + compatible = "microchip,ksz9477"; + reg = <0>; - spi-max-frequency = <44000000>; - spi-cpha; - spi-cpol; + spi-max-frequency = <44000000>; + spi-cpha; + spi-cpol; - ports { - #address-cells = <1>; - #size-cells = <0>; - port@0 { - reg = <0>; - label = "lan1"; - }; - port@1 { - reg = <1>; - label = "lan2"; - }; - port@2 { - reg = <2>; - label = "lan3"; - }; - port@3 { - reg = <3>; - label = "lan4"; - }; - port@4 { - reg = <4>; - label = "lan5"; - }; - port@5 { - reg = <5>; - label = "cpu"; - ethernet = <ð0>; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - }; - }; + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan1"; + }; + port@1 { + reg = <1>; + label = "lan2"; + }; + port@2 { + reg = <2>; + label = "lan3"; + }; + port@3 { + reg = <3>; + label = "lan4"; + }; + port@4 { + reg = <4>; + label = "lan5"; + }; + port@5 { + reg = <5>; + label = "cpu"; + ethernet = <ð0>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + ksz8565: ksz8565@0 { + compatible = "microchip,ksz8565"; + reg = <0>; + + spi-max-frequency = <44000000>; + spi-cpha; + spi-cpol; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan1"; + }; + port@1 { + reg = <1>; + label = "lan2"; + }; + port@2 { + reg = <2>; + label = "lan3"; + }; + port@3 { + reg = <3>; + label = "lan4"; + }; + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <ð0>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/mt7530.txt b/Documentation/devicetree/bindings/net/dsa/mt7530.txt index aa3527f71fdc..47aa205ee0bd 100644 --- a/Documentation/devicetree/bindings/net/dsa/mt7530.txt +++ b/Documentation/devicetree/bindings/net/dsa/mt7530.txt @@ -3,12 +3,16 @@ Mediatek MT7530 Ethernet switch Required properties: -- compatible: Must be compatible = "mediatek,mt7530"; +- compatible: may be compatible = "mediatek,mt7530" + or compatible = "mediatek,mt7621" - #address-cells: Must be 1. - #size-cells: Must be 0. - mediatek,mcm: Boolean; if defined, indicates that either MT7530 is the part on multi-chip module belong to MT7623A has or the remotely standalone chip as the function MT7623N reference board provided for. + +If compatible mediatek,mt7530 is set then the following properties are required + - core-supply: Phandle to the regulator node necessary for the core power. - io-supply: Phandle to the regulator node necessary for the I/O power. See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt diff --git a/Documentation/devicetree/bindings/net/fsl-enetc.txt b/Documentation/devicetree/bindings/net/fsl-enetc.txt new file mode 100644 index 000000000000..c812e25ae90f --- /dev/null +++ b/Documentation/devicetree/bindings/net/fsl-enetc.txt @@ -0,0 +1,69 @@ +* ENETC ethernet device tree bindings + +Depending on board design and ENETC port type (internal or +external) there are two supported link modes specified by +below device tree bindings. + +Required properties: + +- reg : Specifies PCIe Device Number and Function + Number of the ENETC endpoint device, according + to parent node bindings. +- compatible : Should be "fsl,enetc". + +1) The ENETC external port is connected to a MDIO configurable phy: + +In this case, the ENETC node should include a "mdio" sub-node +that in turn should contain the "ethernet-phy" node describing the +external phy. Below properties are required, their bindings +already defined in ethernet.txt or phy.txt, under +Documentation/devicetree/bindings/net/*. + +Required: + +- phy-handle : Phandle to a PHY on the MDIO bus. + Defined in ethernet.txt. + +- phy-connection-type : Defined in ethernet.txt. + +- mdio : "mdio" node, defined in mdio.txt. + +- ethernet-phy : "ethernet-phy" node, defined in phy.txt. + +Example: + + ethernet@0,0 { + compatible = "fsl,enetc"; + reg = <0x000000 0 0 0 0>; + phy-handle = <&sgmii_phy0>; + phy-connection-type = "sgmii"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + sgmii_phy0: ethernet-phy@2 { + reg = <0x2>; + }; + }; + }; + +2) The ENETC port is an internal port or has a fixed-link external +connection: + +In this case, the ENETC port node defines a fixed link connection, +as specified by "fixed-link.txt", under +Documentation/devicetree/bindings/net/*. + +Required: + +- fixed-link : "fixed-link" node, defined in "fixed-link.txt". + +Example: + ethernet@0,2 { + compatible = "fsl,enetc"; + reg = <0x000200 0 0 0 0>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index 3e17ac1d5d58..174f292d8a3e 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -3,8 +3,8 @@ Required properties: - compatible: Should be "cdns,[<chip>-]{macb|gem}" Use "cdns,at91rm9200-emac" Atmel at91rm9200 SoC. - Use "cdns,at91sam9260-macb" for Atmel at91sam9 SoCs or the 10/100Mbit IP - available on sama5d3 SoCs. + Use "cdns,at91sam9260-macb" for Atmel at91sam9 SoCs. + Use "cdns,sam9x60-macb" for Microchip sam9x60 SoC. Use "cdns,np4-macb" for NP4 SoC devices. Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb". Use "cdns,pc302-gem" for Picochip picoXcell pc302 and later devices based on diff --git a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt index bedcfd5a52cd..691f886cfc4a 100644 --- a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt +++ b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt @@ -19,7 +19,7 @@ Optional properties: "marvell,armada-370-neta" and 9800B for others. - clock-names: List of names corresponding to clocks property; shall be "core" for core clock and "bus" for the optional bus clock. - +- phys: comphy for the ethernet port, see ../phy/phy-bindings.txt Optional properties (valid only for Armada XP/38x): diff --git a/Documentation/devicetree/bindings/net/mdio-mux-multiplexer.txt b/Documentation/devicetree/bindings/net/mdio-mux-multiplexer.txt new file mode 100644 index 000000000000..534e38058fe0 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mdio-mux-multiplexer.txt @@ -0,0 +1,82 @@ +Properties for an MDIO bus multiplexer consumer device + +This is a special case of MDIO mux when MDIO mux is defined as a consumer +of a mux producer device. The mux producer can be of any type like mmio mux +producer, gpio mux producer or generic register based mux producer. + +Required properties in addition to the MDIO Bus multiplexer properties: + +- compatible : should be "mmio-mux-multiplexer" +- mux-controls : mux controller node to use for operating the mux +- mdio-parent-bus : phandle to the parent MDIO bus. + +each child node of mdio bus multiplexer consumer device represent a mdio +bus. + +for more information please refer +Documentation/devicetree/bindings/mux/mux-controller.txt +and Documentation/devicetree/bindings/net/mdio-mux.txt + +Example: +In below example the Mux producer and consumer are separate nodes. + +&i2c0 { + fpga@66 { // fpga connected to i2c + compatible = "fsl,lx2160aqds-fpga", "fsl,fpga-qixis-i2c", + "simple-mfd"; + reg = <0x66>; + + mux: mux-controller { // Mux Producer + compatible = "reg-mux"; + #mux-control-cells = <1>; + mux-reg-masks = <0x54 0xf8>, /* 0: reg 0x54, bits 7:3 */ + <0x54 0x07>; /* 1: reg 0x54, bits 2:0 */ + }; + }; +}; + +mdio-mux-1 { // Mux consumer + compatible = "mdio-mux-multiplexer"; + mux-controls = <&mux 0>; + mdio-parent-bus = <&emdio1>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + mdio@8 { + reg = <0x8>; + #address-cells = <1>; + #size-cells = <0>; + }; + + .. + .. +}; + +mdio-mux-2 { // Mux consumer + compatible = "mdio-mux-multiplexer"; + mux-controls = <&mux 1>; + mdio-parent-bus = <&emdio2>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + mdio@1 { + reg = <0x1>; + #address-cells = <1>; + #size-cells = <0>; + }; + + .. + .. +}; diff --git a/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt b/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt index 14ceb2a5b4e8..41a7dcc80f5b 100644 --- a/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt +++ b/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt @@ -33,3 +33,67 @@ Example: clock-names = "ref"; }; }; + +MediaTek UART based Bluetooth Devices +================================== + +This device is a serial attached device to UART device and thus it must be a +child node of the serial node with UART. + +Please refer to the following documents for generic properties: + + Documentation/devicetree/bindings/serial/slave-device.txt + +Required properties: + +- compatible: Must be + "mediatek,mt7663u-bluetooth": for MT7663U device + "mediatek,mt7668u-bluetooth": for MT7668U device +- vcc-supply: Main voltage regulator +- pinctrl-names: Should be "default", "runtime" +- pinctrl-0: Should contain UART RXD low when the device is powered up to + enter proper bootstrap mode. +- pinctrl-1: Should contain UART mode pin ctrl + +Optional properties: + +- reset-gpios: GPIO used to reset the device whose initial state keeps low, + if the GPIO is missing, then board-level design should be + guaranteed. +- current-speed: Current baud rate of the device whose defaults to 921600 + +Example: + + uart1_pins_boot: uart1-default { + pins-dat { + pinmux = <MT7623_PIN_81_URXD1_FUNC_GPIO81>; + output-low; + }; + }; + + uart1_pins_runtime: uart1-runtime { + pins-dat { + pinmux = <MT7623_PIN_81_URXD1_FUNC_URXD1>, + <MT7623_PIN_82_UTXD1_FUNC_UTXD1>; + }; + }; + + uart1: serial@11003000 { + compatible = "mediatek,mt7623-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11003000 0 0x400>; + interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_UART1_SEL>, + <&pericfg CLK_PERI_UART1>; + clock-names = "baud", "bus"; + + bluetooth { + compatible = "mediatek,mt7663u-bluetooth"; + vcc-supply = <®_5v>; + reset-gpios = <&pio 24 GPIO_ACTIVE_LOW>; + pinctrl-names = "default", "runtime"; + pinctrl-0 = <&uart1_pins_boot>; + pinctrl-1 = <&uart1_pins_runtime>; + current-speed = <921600>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/nixge.txt b/Documentation/devicetree/bindings/net/nixge.txt index e55af7f0881a..85d7240a9b20 100644 --- a/Documentation/devicetree/bindings/net/nixge.txt +++ b/Documentation/devicetree/bindings/net/nixge.txt @@ -1,17 +1,53 @@ * NI XGE Ethernet controller Required properties: -- compatible: Should be "ni,xge-enet-2.00" -- reg: Address and length of the register set for the device +- compatible: Should be "ni,xge-enet-3.00", but can be "ni,xge-enet-2.00" for + older device trees with DMA engines co-located in the address map, + with the one reg entry to describe the whole device. +- reg: Address and length of the register set for the device. It contains the + information of registers in the same order as described by reg-names. +- reg-names: Should contain the reg names + "dma": DMA engine control and status region + "ctrl": MDIO and PHY control and status region - interrupts: Should contain tx and rx interrupt - interrupt-names: Should be "rx" and "tx" - phy-mode: See ethernet.txt file in the same directory. -- phy-handle: See ethernet.txt file in the same directory. - nvmem-cells: Phandle of nvmem cell containing the MAC address - nvmem-cell-names: Should be "address" +Optional properties: +- mdio subnode to indicate presence of MDIO controller +- fixed-link : Assume a fixed link. See fixed-link.txt in the same directory. + Use instead of phy-handle. +- phy-handle: See ethernet.txt file in the same directory. + Examples (10G generic PHY): nixge0: ethernet@40000000 { + compatible = "ni,xge-enet-3.00"; + reg = <0x40000000 0x4000 + 0x41002000 0x2000>; + reg-names = "dma", "ctrl"; + + nvmem-cells = <ð1_addr>; + nvmem-cell-names = "address"; + + interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>, <0 30 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "rx", "tx"; + interrupt-parent = <&intc>; + + phy-mode = "xgmii"; + phy-handle = <ðernet_phy1>; + + mdio { + ethernet_phy1: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <4>; + }; + }; + }; + +Examples (10G generic PHY, no MDIO): + nixge0: ethernet@40000000 { compatible = "ni,xge-enet-2.00"; reg = <0x40000000 0x6000>; @@ -24,9 +60,33 @@ Examples (10G generic PHY): phy-mode = "xgmii"; phy-handle = <ðernet_phy1>; + }; + +Examples (1G generic fixed-link + MDIO): + nixge0: ethernet@40000000 { + compatible = "ni,xge-enet-2.00"; + reg = <0x40000000 0x6000>; - ethernet_phy1: ethernet-phy@4 { - compatible = "ethernet-phy-ieee802.3-c45"; - reg = <4>; + nvmem-cells = <ð1_addr>; + nvmem-cell-names = "address"; + + interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>, <0 30 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "rx", "tx"; + interrupt-parent = <&intc>; + + phy-mode = "xgmii"; + + fixed-link { + speed = <1000>; + pause; + link-gpios = <&gpio0 63 GPIO_ACTIVE_HIGH>; + }; + + mdio { + ethernet_phy1: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <4>; + }; }; + }; diff --git a/Documentation/devicetree/bindings/net/qcom,ethqos.txt b/Documentation/devicetree/bindings/net/qcom,ethqos.txt new file mode 100644 index 000000000000..fcf5035810b5 --- /dev/null +++ b/Documentation/devicetree/bindings/net/qcom,ethqos.txt @@ -0,0 +1,64 @@ +Qualcomm Ethernet ETHQOS device + +This documents dwmmac based ethernet device which supports Gigabit +ethernet for version v2.3.0 onwards. + +This device has following properties: + +Required properties: + +- compatible: Should be qcom,qcs404-ethqos" + +- reg: Address and length of the register set for the device + +- reg-names: Should contain register names "stmmaceth", "rgmii" + +- clocks: Should contain phandle to clocks + +- clock-names: Should contain clock names "stmmaceth", "pclk", + "ptp_ref", "rgmii" + +- interrupts: Should contain phandle to interrupts + +- interrupt-names: Should contain interrupt names "macirq", "eth_lpi" + +Rest of the properties are defined in stmmac.txt file in same directory + + +Example: + +ethernet: ethernet@7a80000 { + compatible = "qcom,qcs404-ethqos"; + reg = <0x07a80000 0x10000>, + <0x07a96000 0x100>; + reg-names = "stmmaceth", "rgmii"; + clock-names = "stmmaceth", "pclk", "ptp_ref", "rgmii"; + clocks = <&gcc GCC_ETH_AXI_CLK>, + <&gcc GCC_ETH_SLAVE_AHB_CLK>, + <&gcc GCC_ETH_PTP_CLK>, + <&gcc GCC_ETH_RGMII_CLK>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq", "eth_lpi"; + snps,reset-gpio = <&tlmm 60 GPIO_ACTIVE_LOW>; + snps,reset-active-low; + + snps,txpbl = <8>; + snps,rxpbl = <2>; + snps,aal; + snps,tso; + + phy-handle = <&phy1>; + phy-mode = "rgmii"; + + mdio { + #address-cells = <0x1>; + #size-cells = <0x0>; + compatible = "snps,dwmac-mdio"; + phy1: phy@4 { + device_type = "ethernet-phy"; + reg = <0x4>; + }; + }; + +}; diff --git a/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt index 0c17a0ec9b7b..7b9a776230c0 100644 --- a/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt +++ b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt @@ -4,6 +4,13 @@ This node provides properties for configuring the MediaTek mt76xx wireless device. The node is expected to be specified as a child node of the PCI controller to which the wireless chip is connected. +Alternatively, it can specify the wireless part of the MT7628/MT7688 SoC. +For SoC, use the compatible string "mediatek,mt7628-wmac" and the following +properties: + +- reg: Address and length of the register set for the device. +- interrupts: Main device interrupt + Optional properties: - mac-address: See ethernet.txt in the parent directory @@ -30,3 +37,15 @@ Optional nodes: }; }; }; + +MT7628 example: + +wmac: wmac@10300000 { + compatible = "mediatek,mt7628-wmac"; + reg = <0x10300000 0x100000>; + + interrupt-parent = <&cpuintc>; + interrupts = <6>; + + mediatek,mtd-eeprom = <&factory 0x0000>; +}; diff --git a/Documentation/devicetree/bindings/phy/phy-armada38x-comphy.txt b/Documentation/devicetree/bindings/phy/phy-armada38x-comphy.txt new file mode 100644 index 000000000000..ad49e5c01334 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-armada38x-comphy.txt @@ -0,0 +1,40 @@ +mvebu armada 38x comphy driver +------------------------------ + +This comphy controller can be found on Marvell Armada 38x. It provides a +number of shared PHYs used by various interfaces (network, sata, usb, +PCIe...). + +Required properties: + +- compatible: should be "marvell,armada-380-comphy" +- reg: should contain the comphy register location and length. +- #address-cells: should be 1. +- #size-cells: should be 0. + +A sub-node is required for each comphy lane provided by the comphy. + +Required properties (child nodes): + +- reg: comphy lane number. +- #phy-cells : from the generic phy bindings, must be 1. Defines the + input port to use for a given comphy lane. + +Example: + + comphy: phy@18300 { + compatible = "marvell,armada-380-comphy"; + reg = <0x18300 0x100>; + #address-cells = <1>; + #size-cells = <0>; + + cpm_comphy0: phy@0 { + reg = <0>; + #phy-cells = <1>; + }; + + cpm_comphy1: phy@1 { + reg = <1>; + #phy-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/ptp/ptp-qoriq.txt b/Documentation/devicetree/bindings/ptp/ptp-qoriq.txt index c5d0e7998e2b..454c937076a2 100644 --- a/Documentation/devicetree/bindings/ptp/ptp-qoriq.txt +++ b/Documentation/devicetree/bindings/ptp/ptp-qoriq.txt @@ -17,6 +17,11 @@ Clock Properties: - fsl,tmr-fiper1 Fixed interval period pulse generator. - fsl,tmr-fiper2 Fixed interval period pulse generator. - fsl,max-adj Maximum frequency adjustment in parts per billion. + - fsl,extts-fifo The presence of this property indicates hardware + support for the external trigger stamp FIFO. + - little-endian The presence of this property indicates the 1588 timer + IP block is little-endian mode. The default endian mode + is big-endian. These properties set the operational parameters for the PTP clock. You must choose these carefully for the clock to work right. diff --git a/Documentation/devicetree/bindings/regulator/fan53555.txt b/Documentation/devicetree/bindings/regulator/fan53555.txt index 54a3f2c80e3a..e7fc045281d1 100644 --- a/Documentation/devicetree/bindings/regulator/fan53555.txt +++ b/Documentation/devicetree/bindings/regulator/fan53555.txt @@ -1,7 +1,8 @@ Binding for Fairchild FAN53555 regulators Required properties: - - compatible: one of "fcs,fan53555", "silergy,syr827", "silergy,syr828" + - compatible: one of "fcs,fan53555", "fcs,fan53526", "silergy,syr827" or + "silergy,syr828" - reg: I2C address Optional properties: diff --git a/Documentation/devicetree/bindings/regulator/fixed-regulator.txt b/Documentation/devicetree/bindings/regulator/fixed-regulator.txt deleted file mode 100644 index 0c2a6c8a1536..000000000000 --- a/Documentation/devicetree/bindings/regulator/fixed-regulator.txt +++ /dev/null @@ -1,35 +0,0 @@ -Fixed Voltage regulators - -Required properties: -- compatible: Must be "regulator-fixed"; -- regulator-name: Defined in regulator.txt as optional, but required here. - -Optional properties: -- gpio: gpio to use for enable control -- startup-delay-us: startup time in microseconds -- enable-active-high: Polarity of GPIO is Active high -If this property is missing, the default assumed is Active low. -- gpio-open-drain: GPIO is open drain type. - If this property is missing then default assumption is false. --vin-supply: Input supply name. - -Any property defined as part of the core regulator -binding, defined in regulator.txt, can also be used. -However a fixed voltage regulator is expected to have the -regulator-min-microvolt and regulator-max-microvolt -to be the same. - -Example: - - abc: fixedregulator@0 { - compatible = "regulator-fixed"; - regulator-name = "fixed-supply"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - gpio = <&gpio1 16 0>; - startup-delay-us = <70000>; - enable-active-high; - regulator-boot-on; - gpio-open-drain; - vin-supply = <&parent_reg>; - }; diff --git a/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml b/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml new file mode 100644 index 000000000000..d289c2f7455a --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml @@ -0,0 +1,67 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/fixed-regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Fixed Voltage regulators + +maintainers: + - Liam Girdwood <lgirdwood@gmail.com> + - Mark Brown <broonie@kernel.org> + +description: + Any property defined as part of the core regulator binding, defined in + regulator.txt, can also be used. However a fixed voltage regulator is + expected to have the regulator-min-microvolt and regulator-max-microvolt + to be the same. + +properties: + compatible: + const: regulator-fixed + + regulator-name: true + + gpio: + description: gpio to use for enable control + maxItems: 1 + + startup-delay-us: + description: startup time in microseconds + $ref: /schemas/types.yaml#/definitions/uint32 + + enable-active-high: + description: + Polarity of GPIO is Active high. If this property is missing, + the default assumed is Active low. + type: boolean + + gpio-open-drain: + description: + GPIO is open drain type. If this property is missing then default + assumption is false. + type: boolean + + vin-supply: + description: Input supply phandle. + $ref: /schemas/types.yaml#/definitions/phandle + +required: + - compatible + - regulator-name + +examples: + - | + reg_1v8: regulator-1v8 { + compatible = "regulator-fixed"; + regulator-name = "1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio1 16 0>; + startup-delay-us = <70000>; + enable-active-high; + regulator-boot-on; + gpio-open-drain; + vin-supply = <&parent_reg>; + }; +... diff --git a/Documentation/devicetree/bindings/regulator/max77650-regulator.txt b/Documentation/devicetree/bindings/regulator/max77650-regulator.txt new file mode 100644 index 000000000000..f1cbe813c30f --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max77650-regulator.txt @@ -0,0 +1,41 @@ +Regulator driver for MAX77650 PMIC from Maxim Integrated. + +This module is part of the MAX77650 MFD device. For more details +see Documentation/devicetree/bindings/mfd/max77650.txt. + +The regulator controller is represented as a sub-node of the PMIC node +on the device tree. + +The device has a single LDO regulator and a SIMO buck-boost regulator with +three independent power rails. + +Required properties: +-------------------- +- compatible: Must be "maxim,max77650-regulator" + +Each rail must be instantiated under the regulators subnode of the top PMIC +node. Up to four regulators can be defined. For standard regulator properties +refer to Documentation/devicetree/bindings/regulator/regulator.txt. + +Available regulator compatible strings are: "ldo", "sbb0", "sbb1", "sbb2". + +Example: +-------- + + regulators { + compatible = "maxim,max77650-regulator"; + + max77650_ldo: regulator@0 { + regulator-compatible = "ldo"; + regulator-name = "max77650-ldo"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <2937500>; + }; + + max77650_sbb0: regulator@1 { + regulator-compatible = "sbb0"; + regulator-name = "max77650-sbb0"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1587500>; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/pfuze100.txt b/Documentation/devicetree/bindings/regulator/pfuze100.txt index f9be1acf891c..4d3b12b92cb3 100644 --- a/Documentation/devicetree/bindings/regulator/pfuze100.txt +++ b/Documentation/devicetree/bindings/regulator/pfuze100.txt @@ -8,7 +8,7 @@ Optional properties: - fsl,pfuze-support-disable-sw: Boolean, if present disable all unused switch regulators to save power consumption. Attention, ensure that all important regulators (e.g. DDR ref, DDR supply) has set the "regulator-always-on" - property. If not present, the switched regualtors are always on and can't be + property. If not present, the switched regulators are always on and can't be disabled. This binding is a workaround to keep backward compatibility with old dtb's which rely on the fact that the switched regulators are always on and don't mark them explicit as "regulator-always-on". diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd70528-regulator.txt b/Documentation/devicetree/bindings/regulator/rohm,bd70528-regulator.txt new file mode 100644 index 000000000000..698cfc3bc3dd --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/rohm,bd70528-regulator.txt @@ -0,0 +1,68 @@ +ROHM BD70528 Power Management Integrated Circuit regulator bindings + +Required properties: + - regulator-name: should be "buck1", "buck2", "buck3", "ldo1", "ldo2", "ldo3", + "led_ldo1", "led_ldo2" + +List of regulators provided by this controller. BD70528 regulators node +should be sub node of the BD70528 MFD node. See BD70528 MFD bindings at +Documentation/devicetree/bindings/mfd/rohm,bd70528-pmic.txt + +The valid names for BD70528 regulator nodes are: +BUCK1, BUCK2, BUCK3, LDO1, LDO2, LDO3, LED_LDO1, LED_LDO2 + +Optional properties: +- Any optional property defined in bindings/regulator/regulator.txt + +Example: +regulators { + buck1: BUCK1 { + regulator-name = "buck1"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + regulator-ramp-delay = <125>; + }; + buck2: BUCK2 { + regulator-name = "buck2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-ramp-delay = <125>; + }; + buck3: BUCK3 { + regulator-name = "buck3"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-ramp-delay = <250>; + }; + ldo1: LDO1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + ldo2: LDO2 { + regulator-name = "ldo2"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + ldo3: LDO3 { + regulator-name = "ldo3"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <3300000>; + }; + led_ldo1: LED_LDO1 { + regulator-name = "led_ldo1"; + regulator-min-microvolt = <200000>; + regulator-max-microvolt = <300000>; + }; + led_ldo2: LED_LDO2 { + regulator-name = "led_ldo2"; + regulator-min-microvolt = <200000>; + regulator-max-microvolt = <300000>; + }; +}; diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt index 4b98ca26e61a..cbce62c22b60 100644 --- a/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt @@ -27,8 +27,38 @@ BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6 LDO1, LDO2, LDO3, LDO4, LDO5, LDO6 Optional properties: +- rohm,dvs-run-voltage : PMIC default "RUN" state voltage in uV. + See below table for bucks which support this. +- rohm,dvs-idle-voltage : PMIC default "IDLE" state voltage in uV. + See below table for bucks which support this. +- rohm,dvs-suspend-voltage : PMIC default "SUSPEND" state voltage in uV. + See below table for bucks which support this. - Any optional property defined in bindings/regulator/regulator.txt +Supported default DVS states: + +BD71837: +buck | dvs-run-voltage | dvs-idle-voltage | dvs-suspend-voltage +----------------------------------------------------------------------------- +1 | supported | supported | supported +---------------------------------------------------------------------------- +2 | supported | supported | not supported +---------------------------------------------------------------------------- +3 | supported | not supported | not supported +---------------------------------------------------------------------------- +4 | supported | not supported | not supported +---------------------------------------------------------------------------- +rest | not supported | not supported | not supported + +BD71847: +buck | dvs-run-voltage | dvs-idle-voltage | dvs-suspend-voltage +----------------------------------------------------------------------------- +1 | supported | supported | supported +---------------------------------------------------------------------------- +2 | supported | supported | not supported +---------------------------------------------------------------------------- +rest | not supported | not supported | not supported + Example: regulators { buck1: BUCK1 { @@ -36,7 +66,11 @@ regulators { regulator-min-microvolt = <700000>; regulator-max-microvolt = <1300000>; regulator-boot-on; + regulator-always-on; regulator-ramp-delay = <1250>; + rohm,dvs-run-voltage = <900000>; + rohm,dvs-idle-voltage = <850000>; + rohm,dvs-suspend-voltage = <800000>; }; buck2: BUCK2 { regulator-name = "buck2"; @@ -45,18 +79,22 @@ regulators { regulator-boot-on; regulator-always-on; regulator-ramp-delay = <1250>; + rohm,dvs-run-voltage = <1000000>; + rohm,dvs-idle-voltage = <900000>; }; buck3: BUCK3 { regulator-name = "buck3"; regulator-min-microvolt = <700000>; regulator-max-microvolt = <1300000>; regulator-boot-on; + rohm,dvs-run-voltage = <1000000>; }; buck4: BUCK4 { regulator-name = "buck4"; regulator-min-microvolt = <700000>; regulator-max-microvolt = <1300000>; regulator-boot-on; + rohm,dvs-run-voltage = <1000000>; }; buck5: BUCK5 { regulator-name = "buck5"; diff --git a/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt b/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt index a3f476240565..6189df71ea98 100644 --- a/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt @@ -23,16 +23,14 @@ Switches are fixed voltage regulators with only enable/disable capability. Optional properties: - st,mask-reset: mask reset for this regulator: the regulator configuration is maintained during pmic reset. -- regulator-pull-down: enable high pull down - if not specified light pull down is used - regulator-over-current-protection: if set, all regulators are switched off in case of over-current detection on this regulator, if not set, the driver only sends an over-current event. -- interrupt-parent: phandle to the parent interrupt controller - interrupts: index of current limit detection interrupt - <regulator>-supply: phandle to the parent supply/regulator node each regulator supply can be described except vref_ddr. +- regulator-active-discharge: can be used on pwr_sw1 and pwr_sw2. Example: regulators { @@ -43,7 +41,6 @@ regulators { vdd_core: buck1 { regulator-name = "vdd_core"; interrupts = <IT_CURLIM_BUCK1 0>; - interrupt-parent = <&pmic>; st,mask-reset; regulator-pull-down; regulator-min-microvolt = <700000>; @@ -53,7 +50,6 @@ regulators { v3v3: buck4 { regulator-name = "v3v3"; interrupts = <IT_CURLIM_BUCK4 0>; - interrupt-parent = <&mypmic>; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; diff --git a/Documentation/devicetree/bindings/regulator/tps65218.txt b/Documentation/devicetree/bindings/regulator/tps65218.txt index 02f0e9bbfbf8..54aded3b78e2 100644 --- a/Documentation/devicetree/bindings/regulator/tps65218.txt +++ b/Documentation/devicetree/bindings/regulator/tps65218.txt @@ -71,8 +71,13 @@ tps65218: tps65218@24 { regulator-always-on; }; + ls2: regulator-ls2 { + regulator-min-microamp = <100000>; + regulator-max-microamp = <1000000>; + }; + ls3: regulator-ls3 { - regulator-min-microvolt = <100000>; - regulator-max-microvolt = <1000000>; + regulator-min-microamp = <100000>; + regulator-max-microamp = <1000000>; }; }; diff --git a/Documentation/devicetree/bindings/serio/olpc,ap-sp.txt b/Documentation/devicetree/bindings/serio/olpc,ap-sp.txt index 36603419d6f8..0e72183f52bc 100644 --- a/Documentation/devicetree/bindings/serio/olpc,ap-sp.txt +++ b/Documentation/devicetree/bindings/serio/olpc,ap-sp.txt @@ -4,14 +4,10 @@ Required properties: - compatible : "olpc,ap-sp" - reg : base address and length of SoC's WTM registers - interrupts : SP-AP interrupt -- clocks : phandle + clock-specifier for the clock that drives the WTM -- clock-names: should be "sp" Example: ap-sp@d4290000 { compatible = "olpc,ap-sp"; reg = <0xd4290000 0x1000>; interrupts = <40>; - clocks = <&soc_clocks MMP2_CLK_SP>; - clock-names = "sp"; } diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt index 0b8cc533ca83..cf759e5f9b10 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt @@ -55,7 +55,7 @@ of these nodes are defined by the individual bindings for the specific function = EXAMPLE The following example represents the GLINK RPM node on a MSM8996 device, with the function for the "rpm_request" channel defined, which is used for -regualtors and root clocks. +regulators and root clocks. apcs_glb: mailbox@9820000 { compatible = "qcom,msm8996-apcs-hmss-global"; diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt index a35af2dafdad..49e1d72d3648 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt @@ -41,12 +41,12 @@ processor ID) and a string identifier. - qcom,local-pid: Usage: required Value type: <u32> - Definition: specifies the identfier of the local endpoint of this edge + Definition: specifies the identifier of the local endpoint of this edge - qcom,remote-pid: Usage: required Value type: <u32> - Definition: specifies the identfier of the remote endpoint of this edge + Definition: specifies the identifier of the remote endpoint of this edge = SUBNODES Each SMP2P pair contain a set of inbound and outbound entries, these are diff --git a/Documentation/devicetree/bindings/spi/atmel-quadspi.txt b/Documentation/devicetree/bindings/spi/atmel-quadspi.txt index b93c1e2f25dd..7c40ea694352 100644 --- a/Documentation/devicetree/bindings/spi/atmel-quadspi.txt +++ b/Documentation/devicetree/bindings/spi/atmel-quadspi.txt @@ -1,14 +1,19 @@ * Atmel Quad Serial Peripheral Interface (QSPI) Required properties: -- compatible: Should be "atmel,sama5d2-qspi". +- compatible: Should be one of the following: + - "atmel,sama5d2-qspi" + - "microchip,sam9x60-qspi" - reg: Should contain the locations and lengths of the base registers and the mapped memory. - reg-names: Should contain the resource reg names: - qspi_base: configuration register address space - qspi_mmap: memory mapped address space - interrupts: Should contain the interrupt for the device. -- clocks: The phandle of the clock needed by the QSPI controller. +- clocks: Should reference the peripheral clock and the QSPI system + clock if available. +- clock-names: Should contain "pclk" for the peripheral clock and "qspick" + for the system clock when available. - #address-cells: Should be <1>. - #size-cells: Should be <0>. @@ -19,7 +24,8 @@ spi@f0020000 { reg = <0xf0020000 0x100>, <0xd0000000 0x8000000>; reg-names = "qspi_base", "qspi_mmap"; interrupts = <52 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&spi0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 52>; + clock-names = "pclk"; #address-cells = <1>; #size-cells = <0>; pinctrl-names = "default"; diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt index e3c48b20b1a6..2d3264140cc5 100644 --- a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt @@ -10,6 +10,7 @@ Required properties: - "fsl,imx35-cspi" for SPI compatible with the one integrated on i.MX35 - "fsl,imx51-ecspi" for SPI compatible with the one integrated on i.MX51 - "fsl,imx53-ecspi" for SPI compatible with the one integrated on i.MX53 and later Soc + - "fsl,imx8mq-ecspi" for SPI compatible with the one integrated on i.MX8M - reg : Offset and length of the register set for the device - interrupts : Should contain CSPI/eCSPI interrupt - clocks : Clock specifiers for both ipg and per clocks. diff --git a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-qspi.txt index 483e9cfac1b1..e8f1d627d288 100644 --- a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-fsl-qspi.txt @@ -14,15 +14,13 @@ Required properties: - clocks : The clocks needed by the QuadSPI controller - clock-names : Should contain the name of the clocks: "qspi_en" and "qspi". -Optional properties: - - fsl,qspi-has-second-chip: The controller has two buses, bus A and bus B. - Each bus can be connected with two NOR flashes. - Most of the time, each bus only has one NOR flash - connected, this is the default case. - But if there are two NOR flashes connected to the - bus, you should enable this property. - (Please check the board's schematic.) - - big-endian : That means the IP register is big endian +Required SPI slave node properties: + - reg: There are two buses (A and B) with two chip selects each. + This encodes to which bus and CS the flash is connected: + <0>: Bus A, CS 0 + <1>: Bus A, CS 1 + <2>: Bus B, CS 0 + <3>: Bus B, CS 1 Example: @@ -40,7 +38,7 @@ qspi0: quadspi@40044000 { }; }; -Example showing the usage of two SPI NOR devices: +Example showing the usage of two SPI NOR devices on bus A: &qspi2 { pinctrl-names = "default"; diff --git a/Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt b/Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt new file mode 100644 index 000000000000..2cd67eb727d4 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt @@ -0,0 +1,39 @@ +* NXP Flex Serial Peripheral Interface (FSPI) + +Required properties: + - compatible : Should be "nxp,lx2160a-fspi" + - reg : First contains the register location and length, + Second contains the memory mapping address and length + - reg-names : Should contain the resource reg names: + - fspi_base: configuration register address space + - fspi_mmap: memory mapped address space + - interrupts : Should contain the interrupt for the device + +Required SPI slave node properties: + - reg : There are two buses (A and B) with two chip selects each. + This encodes to which bus and CS the flash is connected: + - <0>: Bus A, CS 0 + - <1>: Bus A, CS 1 + - <2>: Bus B, CS 0 + - <3>: Bus B, CS 1 + +Example showing the usage of two SPI NOR slave devices on bus A: + +fspi0: spi@20c0000 { + compatible = "nxp,lx2160a-fspi"; + reg = <0x0 0x20c0000 0x0 0x10000>, <0x0 0x20000000 0x0 0x10000000>; + reg-names = "fspi_base", "fspi_mmap"; + interrupts = <0 25 0x4>; /* Level high type */ + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "fspi_en", "fspi"; + + mt35xu512aba0: flash@0 { + reg = <0>; + .... + }; + + mt35xu512aba1: flash@1 { + reg = <1>; + .... + }; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-sifive.txt b/Documentation/devicetree/bindings/spi/spi-sifive.txt new file mode 100644 index 000000000000..3f5c6e438972 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-sifive.txt @@ -0,0 +1,37 @@ +SiFive SPI controller Device Tree Bindings +------------------------------------------ + +Required properties: +- compatible : Should be "sifive,<chip>-spi" and "sifive,spi<version>". + Supported compatible strings are: + "sifive,fu540-c000-spi" for the SiFive SPI v0 as integrated + onto the SiFive FU540 chip, and "sifive,spi0" for the SiFive + SPI v0 IP block with no chip integration tweaks. + Please refer to sifive-blocks-ip-versioning.txt for details +- reg : Physical base address and size of SPI registers map + A second (optional) range can indicate memory mapped flash +- interrupts : Must contain one entry +- interrupt-parent : Must be core interrupt controller +- clocks : Must reference the frequency given to the controller +- #address-cells : Must be '1', indicating which CS to use +- #size-cells : Must be '0' + +Optional properties: +- sifive,fifo-depth : Depth of hardware queues; defaults to 8 +- sifive,max-bits-per-word : Maximum bits per word; defaults to 8 + +SPI RTL that corresponds to the IP block version numbers can be found here: +https://github.com/sifive/sifive-blocks/tree/master/src/main/scala/devices/spi + +Example: + spi: spi@10040000 { + compatible = "sifive,fu540-c000-spi", "sifive,spi0"; + reg = <0x0 0x10040000 0x0 0x1000 0x0 0x20000000 0x0 0x10000000>; + interrupt-parent = <&plic>; + interrupts = <51>; + clocks = <&tlclk>; + #address-cells = <1>; + #size-cells = <0>; + sifive,fifo-depth = <8>; + sifive,max-bits-per-word = <8>; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-sprd.txt b/Documentation/devicetree/bindings/spi/spi-sprd.txt index bad211a19da4..3c7eacce0ee3 100644 --- a/Documentation/devicetree/bindings/spi/spi-sprd.txt +++ b/Documentation/devicetree/bindings/spi/spi-sprd.txt @@ -14,6 +14,11 @@ Required properties: address on the SPI bus. Should be set to 1. - #size-cells: Should be set to 0. +Optional properties: +dma-names: Should contain names of the SPI used DMA channel. +dmas: Should contain DMA channels and DMA slave ids which the SPI used + sorted in the same order as the dma-names property. + Example: spi0: spi@70a00000{ compatible = "sprd,sc9860-spi"; @@ -21,6 +26,8 @@ spi0: spi@70a00000{ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; clock-names = "spi", "source","enable"; clocks = <&clk_spi0>, <&ext_26m>, <&clk_ap_apb_gates 5>; + dma-names = "rx_chn", "tx_chn"; + dmas = <&apdma 11 11>, <&apdma 12 12>; #address-cells = <1>; #size-cells = <0>; }; diff --git a/Documentation/devicetree/bindings/spi/spi-stm32.txt b/Documentation/devicetree/bindings/spi/spi-stm32.txt index 1b3fa2c119d5..d82755c63eaf 100644 --- a/Documentation/devicetree/bindings/spi/spi-stm32.txt +++ b/Documentation/devicetree/bindings/spi/spi-stm32.txt @@ -7,7 +7,9 @@ from 4 to 32-bit data size. Although it can be configured as master or slave, only master is supported by the driver. Required properties: -- compatible: Must be "st,stm32h7-spi". +- compatible: Should be one of: + "st,stm32h7-spi" + "st,stm32f4-spi" - reg: Offset and length of the device's register set. - interrupts: Must contain the interrupt id. - clocks: Must contain an entry for spiclk (which feeds the internal clock @@ -30,8 +32,9 @@ Child nodes represent devices on the SPI bus See ../spi/spi-bus.txt Optional properties: -- st,spi-midi-ns: (Master Inter-Data Idleness) minimum time delay in - nanoseconds inserted between two consecutive data frames. +- st,spi-midi-ns: Only for STM32H7, (Master Inter-Data Idleness) minimum time + delay in nanoseconds inserted between two consecutive data + frames. Example: diff --git a/Documentation/devicetree/bindings/trivial-devices.yaml b/Documentation/devicetree/bindings/trivial-devices.yaml index cc64ec63a6ad..d79fb22bde39 100644 --- a/Documentation/devicetree/bindings/trivial-devices.yaml +++ b/Documentation/devicetree/bindings/trivial-devices.yaml @@ -322,6 +322,8 @@ properties: - ti,ads7830 # Temperature Monitoring and Fan Control - ti,amc6821 + # Temperature sensor with integrated fan control + - ti,lm96000 # I2C Touch-Screen Controller - ti,tsc2003 # Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface |