diff options
Diffstat (limited to 'Documentation/devicetree')
51 files changed, 1303 insertions, 99 deletions
diff --git a/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt b/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt index 832fe8cc24d7..adc61b095bd1 100644 --- a/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt +++ b/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt @@ -14,14 +14,21 @@ Required properties: for exynos4412/5250 controllers. Must be "samsung,exynos-adc-v2" for future controllers. + Must be "samsung,exynos3250-adc" for + controllers compatible with ADC of Exynos3250. - reg: Contains ADC register address range (base address and length) and the address of the phy enable register. - interrupts: Contains the interrupt information for the timer. The format is being dependent on which interrupt controller the Samsung device uses. - #io-channel-cells = <1>; As ADC has multiple outputs -- clocks From common clock binding: handle to adc clock. -- clock-names From common clock binding: Shall be "adc". +- clocks From common clock bindings: handles to clocks specified + in "clock-names" property, in the same order. +- clock-names From common clock bindings: list of clock input names + used by ADC block: + - "adc" : ADC bus clock + - "sclk" : ADC special clock (only for Exynos3250 and + compatible ADC block) - vdd-supply VDD input supply. Note: child nodes can be added for auto probing from device tree. @@ -41,6 +48,20 @@ adc: adc@12D10000 { vdd-supply = <&buck5_reg>; }; +Example: adding device info in dtsi file for Exynos3250 with additional sclk + +adc: adc@126C0000 { + compatible = "samsung,exynos3250-adc", "samsung,exynos-adc-v2; + reg = <0x126C0000 0x100>, <0x10020718 0x4>; + interrupts = <0 137 0>; + #io-channel-cells = <1>; + io-channel-ranges; + + clocks = <&cmu CLK_TSADC>, <&cmu CLK_SCLK_TSADC>; + clock-names = "adc", "sclk"; + + vdd-supply = <&buck5_reg>; +}; Example: Adding child nodes in dts file diff --git a/Documentation/devicetree/bindings/arm/samsung/pmu.txt b/Documentation/devicetree/bindings/arm/samsung/pmu.txt index 2a4ab046a8a1..f9865e77e0b0 100644 --- a/Documentation/devicetree/bindings/arm/samsung/pmu.txt +++ b/Documentation/devicetree/bindings/arm/samsung/pmu.txt @@ -12,8 +12,38 @@ Properties: - reg : offset and length of the register set. + - #clock-cells : must be <1>, since PMU requires once cell as clock specifier. + The single specifier cell is used as index to list of clocks + provided by PMU, which is currently: + 0 : SoC clock output (CLKOUT pin) + + - clock-names : list of clock names for particular CLKOUT mux inputs in + following format: + "clkoutN", where N is a decimal number corresponding to + CLKOUT mux control bits value for given input, e.g. + "clkout0", "clkout7", "clkout15". + + - clocks : list of phandles and specifiers to all input clocks listed in + clock-names property. + Example : pmu_system_controller: system-controller@10040000 { compatible = "samsung,exynos5250-pmu", "syscon"; reg = <0x10040000 0x5000>; + #clock-cells = <1>; + clock-names = "clkout0", "clkout1", "clkout2", "clkout3", + "clkout4", "clkout8", "clkout9"; + clocks = <&clock CLK_OUT_DMC>, <&clock CLK_OUT_TOP>, + <&clock CLK_OUT_LEFTBUS>, <&clock CLK_OUT_RIGHTBUS>, + <&clock CLK_OUT_CPU>, <&clock CLK_XXTI>, + <&clock CLK_XUSBXTI>; +}; + +Example of clock consumer : + +usb3503: usb3503@08 { + /* ... */ + clock-names = "refclk"; + clocks = <&pmu_system_controller 0>; + /* ... */ }; diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt index c96d8dcf98fd..4ab09f2202d4 100644 --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -3,28 +3,43 @@ SATA nodes are defined to describe on-chip Serial ATA controllers. Each SATA controller should have its own node. +It is possible, but not required, to represent each port as a sub-node. +It allows to enable each port independently when dealing with multiple +PHYs. + Required properties: - compatible : compatible string, one of: - "allwinner,sun4i-a10-ahci" - - "fsl,imx53-ahci" - - "fsl,imx6q-ahci" - "hisilicon,hisi-ahci" - "ibm,476gtr-ahci" - "marvell,armada-380-ahci" - "snps,dwc-ahci" - "snps,exynos5440-ahci" - "snps,spear-ahci" + - "generic-ahci" - interrupts : <interrupt mapping for SATA IRQ> - reg : <registers mapping> +Please note that when using "generic-ahci" you must also specify a SoC specific +compatible: + compatible = "manufacturer,soc-model-ahci", "generic-ahci"; + Optional properties: - dma-coherent : Present if dma operations are coherent - clocks : a list of phandle + clock specifier pairs - target-supply : regulator for SATA target power +- phys : reference to the SATA PHY node +- phy-names : must be "sata-phy" + +Required properties when using sub-nodes: +- #address-cells : number of cells to encode an address +- #size-cells : number of cells representing the size of an address + + +Sub-nodes required properties: +- reg : the port number +- phys : reference to the SATA PHY node -"fsl,imx53-ahci", "fsl,imx6q-ahci" required properties: -- clocks : must contain the sata, sata_ref and ahb clocks -- clock-names : must contain "ahb" for the ahb clock Examples: sata@ffe08000 { @@ -40,3 +55,23 @@ Examples: clocks = <&pll6 0>, <&ahb_gates 25>; target-supply = <®_ahci_5v>; }; + +With sub-nodes: + sata@f7e90000 { + compatible = "marvell,berlin2q-achi", "generic-ahci"; + reg = <0xe90000 0x1000>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&chip CLKID_SATA>; + #address-cells = <1>; + #size-cells = <0>; + + sata0: sata-port@0 { + reg = <0>; + phys = <&sata_phy 0>; + }; + + sata1: sata-port@1 { + reg = <1>; + phys = <&sata_phy 1>; + }; + }; diff --git a/Documentation/devicetree/bindings/ata/ahci-st.txt b/Documentation/devicetree/bindings/ata/ahci-st.txt new file mode 100644 index 000000000000..0574a77a0b9f --- /dev/null +++ b/Documentation/devicetree/bindings/ata/ahci-st.txt @@ -0,0 +1,31 @@ +STMicroelectronics STi SATA controller + +This binding describes a SATA device. + +Required properties: + - compatible : Must be "st,sti-ahci" + - reg : Physical base addresses and length of register sets + - interrupts : Interrupt associated with the SATA device + - interrupt-names : Associated name must be; "hostc" + - resets : The power-down and soft-reset lines of SATA IP + - reset-names : Associated names must be; "pwr-dwn" and "sw-rst" + - clocks : The phandle for the clock + - clock-names : Associated name must be; "ahci_clk" + - phys : The phandle for the PHY device + - phy-names : Associated name must be; "ahci_phy" + +Example: + + sata0: sata@fe380000 { + compatible = "st,sti-ahci"; + reg = <0xfe380000 0x1000>; + interrupts = <GIC_SPI 157 IRQ_TYPE_NONE>; + interrupt-names = "hostc"; + phys = <&miphy365x_phy MIPHY_PORT_0 MIPHY_TYPE_SATA>; + phy-names = "ahci_phy"; + resets = <&powerdown STIH416_SATA0_POWERDOWN>, + <&softreset STIH416_SATA0_SOFTRESET>; + reset-names = "pwr-dwn", "sw-rst"; + clocks = <&clk_s_a0_ls CLK_ICN_REG>; + clock-names = "ahci_clk"; + }; diff --git a/Documentation/devicetree/bindings/ata/imx-sata.txt b/Documentation/devicetree/bindings/ata/imx-sata.txt new file mode 100644 index 000000000000..fa511db18408 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/imx-sata.txt @@ -0,0 +1,36 @@ +* Freescale i.MX AHCI SATA Controller + +The Freescale i.MX SATA controller mostly conforms to the AHCI interface +with some special extensions at integration level. + +Required properties: +- compatible : should be one of the following: + - "fsl,imx53-ahci" for i.MX53 SATA controller + - "fsl,imx6q-ahci" for i.MX6Q SATA controller +- interrupts : interrupt mapping for SATA IRQ +- reg : registers mapping +- clocks : list of clock specifiers, must contain an entry for each + required entry in clock-names +- clock-names : should include "sata", "sata_ref" and "ahb" entries + +Optional properties: +- fsl,transmit-level-mV : transmit voltage level, in millivolts. +- fsl,transmit-boost-mdB : transmit boost level, in milli-decibels +- fsl,transmit-atten-16ths : transmit attenuation, in 16ths +- fsl,receive-eq-mdB : receive equalisation, in milli-decibels + Please refer to the technical documentation or the driver source code + for the list of legal values for these options. +- fsl,no-spread-spectrum : disable spread-spectrum clocking on the SATA + link. + +Examples: + +sata@02200000 { + compatible = "fsl,imx6q-ahci"; + reg = <0x02200000 0x4000>; + interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6QDL_CLK_SATA>, + <&clks IMX6QDL_CLK_SATA_REF_100M>, + <&clks IMX6QDL_CLK_AHB>; + clock-names = "sata", "sata_ref", "ahb"; +}; diff --git a/Documentation/devicetree/bindings/ata/tegra-sata.txt b/Documentation/devicetree/bindings/ata/tegra-sata.txt new file mode 100644 index 000000000000..946f2072570b --- /dev/null +++ b/Documentation/devicetree/bindings/ata/tegra-sata.txt @@ -0,0 +1,30 @@ +Tegra124 SoC SATA AHCI controller + +Required properties : +- compatible : "nvidia,tegra124-ahci". +- reg : Should contain 2 entries: + - AHCI register set (SATA BAR5) + - SATA register set +- interrupts : Defines the interrupt used by SATA +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names : Must include the following entries: + - sata + - sata-oob + - cml1 + - pll_e +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + - sata + - sata-oob + - sata-cold +- phys : Must contain an entry for each entry in phy-names. + See ../phy/phy-bindings.txt for details. +- phy-names : Must include the following entries: + - sata-phy : XUSB PADCTL SATA PHY +- hvdd-supply : Defines the SATA HVDD regulator +- vddio-supply : Defines the SATA VDDIO regulator +- avdd-supply : Defines the SATA AVDD regulator +- target-5v-supply : Defines the SATA 5V power regulator +- target-12v-supply : Defines the SATA 12V power regulator diff --git a/Documentation/devicetree/bindings/clock/clk-palmas-clk32kg-clocks.txt b/Documentation/devicetree/bindings/clock/clk-palmas-clk32kg-clocks.txt new file mode 100644 index 000000000000..4208886d834a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/clk-palmas-clk32kg-clocks.txt @@ -0,0 +1,35 @@ +* Palmas 32KHz clocks * + +Palmas device has two clock output pins for 32KHz, KG and KG_AUDIO. + +This binding uses the common clock binding ./clock-bindings.txt. + +Required properties: +- compatible : "ti,palmas-clk32kg" for clk32kg clock + "ti,palmas-clk32kgaudio" for clk32kgaudio clock +- #clock-cells : shall be set to 0. + +Optional property: +- ti,external-sleep-control: The external enable input pins controlled the + enable/disable of clocks. The external enable input pins ENABLE1, + ENABLE2 and NSLEEP. The valid values for the external pins are: + PALMAS_EXT_CONTROL_PIN_ENABLE1 for ENABLE1 pin + PALMAS_EXT_CONTROL_PIN_ENABLE2 for ENABLE2 pin + PALMAS_EXT_CONTROL_PIN_NSLEEP for NSLEEP pin + Option 0 or missing this property means the clock is enabled/disabled + via register access and these pins do not have any control. + The macros of external control pins for DTS is defined at + dt-bindings/mfd/palmas.h + +Example: + #include <dt-bindings/mfd/palmas.h> + ... + palmas: tps65913@58 { + ... + clk32kg: palmas_clk32k@0 { + compatible = "ti,palmas-clk32kg"; + #clock-cells = <0>; + ti,external-sleep-control = <PALMAS_EXT_CONTROL_PIN_NSLEEP>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/clock/clock-bindings.txt b/Documentation/devicetree/bindings/clock/clock-bindings.txt index f15787817d6b..06fc6d541c89 100644 --- a/Documentation/devicetree/bindings/clock/clock-bindings.txt +++ b/Documentation/devicetree/bindings/clock/clock-bindings.txt @@ -131,3 +131,39 @@ clock signal, and a UART. ("pll" and "pll-switched"). * The UART has its baud clock connected the external oscillator and its register clock connected to the PLL clock (the "pll-switched" signal) + +==Assigned clock parents and rates== + +Some platforms may require initial configuration of default parent clocks +and clock frequencies. Such a configuration can be specified in a device tree +node through assigned-clocks, assigned-clock-parents and assigned-clock-rates +properties. The assigned-clock-parents property should contain a list of parent +clocks in form of phandle and clock specifier pairs, the assigned-clock-parents +property the list of assigned clock frequency values - corresponding to clocks +listed in the assigned-clocks property. + +To skip setting parent or rate of a clock its corresponding entry should be +set to 0, or can be omitted if it is not followed by any non-zero entry. + + uart@a000 { + compatible = "fsl,imx-uart"; + reg = <0xa000 0x1000>; + ... + clocks = <&osc 0>, <&pll 1>; + clock-names = "baud", "register"; + + assigned-clocks = <&clkcon 0>, <&pll 2>; + assigned-clock-parents = <&pll 2>; + assigned-clock-rates = <0>, <460800>; + }; + +In this example the <&pll 2> clock is set as parent of clock <&clkcon 0> and +the <&pll 2> clock is assigned a frequency value of 460800 Hz. + +Configuring a clock's parent and rate through the device node that consumes +the clock can be done only for clocks that have a single user. Specifying +conflicting parent or rate configuration in multiple consumer nodes for +a shared clock is forbidden. + +Configuration of common clocks, which affect multiple consumer devices can +be similarly specified in the clock provider node. diff --git a/Documentation/devicetree/bindings/clock/clps711x-clock.txt b/Documentation/devicetree/bindings/clock/clps711x-clock.txt new file mode 100644 index 000000000000..ce5a7476f05d --- /dev/null +++ b/Documentation/devicetree/bindings/clock/clps711x-clock.txt @@ -0,0 +1,19 @@ +* Clock bindings for the Cirrus Logic CLPS711X CPUs + +Required properties: +- compatible : Shall contain "cirrus,clps711x-clk". +- reg : Address of the internal register set. +- startup-frequency: Factory set CPU startup frequency in HZ. +- #clock-cells : Should be <1>. + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/clps711x-clock.h +for the full list of CLPS711X clock IDs. + +Example: + clks: clks@80000000 { + #clock-cells = <1>; + compatible = "cirrus,ep7312-clk", "cirrus,clps711x-clk"; + reg = <0x80000000 0xc000>; + startup-frequency = <73728000>; + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,gcc.txt b/Documentation/devicetree/bindings/clock/qcom,gcc.txt index 9cfcb4f2bc97..aba3d254e037 100644 --- a/Documentation/devicetree/bindings/clock/qcom,gcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,gcc.txt @@ -5,6 +5,8 @@ Required properties : - compatible : shall contain only one of the following: "qcom,gcc-apq8064" + "qcom,gcc-apq8084" + "qcom,gcc-ipq8064" "qcom,gcc-msm8660" "qcom,gcc-msm8960" "qcom,gcc-msm8974" diff --git a/Documentation/devicetree/bindings/clock/qcom,mmcc.txt b/Documentation/devicetree/bindings/clock/qcom,mmcc.txt index d572e9964c54..29ebf84d25af 100644 --- a/Documentation/devicetree/bindings/clock/qcom,mmcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,mmcc.txt @@ -4,6 +4,8 @@ Qualcomm Multimedia Clock & Reset Controller Binding Required properties : - compatible : shall contain only one of the following: + "qcom,mmcc-apq8064" + "qcom,mmcc-apq8084" "qcom,mmcc-msm8660" "qcom,mmcc-msm8960" "qcom,mmcc-msm8974" diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt new file mode 100644 index 000000000000..0c2bf5eba43e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt @@ -0,0 +1,61 @@ +* Rockchip RK3188/RK3066 Clock and Reset Unit + +The RK3188/RK3066 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3188-cru", "rockchip,rk3188a-cru" or + "rockchip,rk3066a-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3188-cru.h and +dt-bindings/clock/rk3066-cru.h headers and can be used in device tree sources. +Similar macros exist for the reset sources in these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "xin32k" - rtc clock - optional, + - "xin27m" - 27mhz crystal input on rk3066 - optional, + - "ext_hsadc" - external HSADC clock - optional, + - "ext_cif0" - external camera clock - optional, + - "ext_rmii" - external RMII clock - optional, + - "ext_jtag" - externalJTAG clock - optional + +Example: Clock controller node: + + cru: cru@20000000 { + compatible = "rockchip,rk3188-cru"; + reg = <0x20000000 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@10124000 { + compatible = "snps,dw-apb-uart"; + reg = <0x10124000 0x400>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <1>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt new file mode 100644 index 000000000000..c9fbb76573e1 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt @@ -0,0 +1,61 @@ +* Rockchip RK3288 Clock and Reset Unit + +The RK3288 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3288-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3288-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "xin32k" - rtc clock - optional, + - "ext_i2s" - external I2S clock - optional, + - "ext_hsadc" - external HSADC clock - optional, + - "ext_edp_24m" - external display port clock - optional, + - "ext_vip" - external VIP clock - optional, + - "ext_isp" - external ISP clock - optional, + - "ext_jtag" - external JTAG clock - optional + +Example: Clock controller node: + + cru: cru@20000000 { + compatible = "rockchip,rk3188-cru"; + reg = <0x20000000 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@10124000 { + compatible = "snps,dw-apb-uart"; + reg = <0x10124000 0x400>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <1>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip.txt b/Documentation/devicetree/bindings/clock/rockchip.txt index a891c823ed44..22f6769e5d4a 100644 --- a/Documentation/devicetree/bindings/clock/rockchip.txt +++ b/Documentation/devicetree/bindings/clock/rockchip.txt @@ -6,6 +6,9 @@ This binding uses the common clock binding[1]. == Gate clocks == +These bindings are deprecated! +Please use the soc specific CRU bindings instead. + The gate registers form a continuos block which makes the dt node structure a matter of taste, as either all gates can be put into one gate clock spanning all registers or they can be divided into diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-divmux.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-divmux.txt index ae56315fcec5..6247652044a0 100644 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen-divmux.txt +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-divmux.txt @@ -24,26 +24,26 @@ Required properties: Example: - clockgenA@fd345000 { + clockgen-a@fd345000 { reg = <0xfd345000 0xb50>; - CLK_M_A1_DIV1: CLK_M_A1_DIV1 { + clk_m_a1_div1: clk-m-a1-div1 { #clock-cells = <1>; compatible = "st,clkgena-divmux-c32-odf1", "st,clkgena-divmux"; - clocks = <&CLK_M_A1_OSC_PREDIV>, - <&CLK_M_A1_PLL0 1>, /* PLL0 PHI1 */ - <&CLK_M_A1_PLL1 1>; /* PLL1 PHI1 */ - - clock-output-names = "CLK_M_RX_ICN_TS", - "CLK_M_RX_ICN_VDP_0", - "", /* Unused */ - "CLK_M_PRV_T1_BUS", - "CLK_M_ICN_REG_12", - "CLK_M_ICN_REG_10", - "", /* Unused */ - "CLK_M_ICN_ST231"; + clocks = <&clk_m_a1_osc_prediv>, + <&clk_m_a1_pll0 1>, /* PLL0 PHI1 */ + <&clk_m_a1_pll1 1>; /* PLL1 PHI1 */ + + clock-output-names = "clk-m-rx-icn-ts", + "clk-m-rx-icn-vdp-0", + "", /* unused */ + "clk-m-prv-t1-bus", + "clk-m-icn-reg-12", + "clk-m-icn-reg-10", + "", /* unused */ + "clk-m-icn-st231"; }; }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt index 943e0808e212..f1fa91c68768 100644 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt @@ -17,7 +17,7 @@ Required properties: "st,stih416-clkgenf-vcc-sd", "st,clkgen-mux" "st,stih415-clkgen-a9-mux", "st,clkgen-mux" "st,stih416-clkgen-a9-mux", "st,clkgen-mux" - + "st,stih407-clkgen-a9-mux", "st,clkgen-mux" - #clock-cells : from common clock binding; shall be set to 0. @@ -27,10 +27,10 @@ Required properties: Example: - CLK_M_HVA: CLK_M_HVA { + clk_m_hva: clk-m-hva@fd690868 { #clock-cells = <0>; compatible = "st,stih416-clkgenf-vcc-hva", "st,clkgen-mux"; reg = <0xfd690868 4>; - clocks = <&CLOCKGEN_F 1>, <&CLK_M_A1_DIV0 3>; + clocks = <&clockgen_f 1>, <&clk_m_a1_div0 3>; }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt index 81eb3855ab92..efb51cf0c845 100644 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt @@ -19,11 +19,14 @@ Required properties: "st,stih415-plls-c32-ddr", "st,clkgen-plls-c32" "st,stih416-plls-c32-a9", "st,clkgen-plls-c32" "st,stih416-plls-c32-ddr", "st,clkgen-plls-c32" + "st,stih407-plls-c32-a0", "st,clkgen-plls-c32" + "st,stih407-plls-c32-a9", "st,clkgen-plls-c32" + "st,stih407-plls-c32-c0_0", "st,clkgen-plls-c32" + "st,stih407-plls-c32-c0_1", "st,clkgen-plls-c32" "st,stih415-gpu-pll-c32", "st,clkgengpu-pll-c32" "st,stih416-gpu-pll-c32", "st,clkgengpu-pll-c32" - - #clock-cells : From common clock binding; shall be set to 1. - clocks : From common clock binding @@ -32,17 +35,17 @@ Required properties: Example: - clockgenA@fee62000 { + clockgen-a@fee62000 { reg = <0xfee62000 0xb48>; - CLK_S_A0_PLL: CLK_S_A0_PLL { + clk_s_a0_pll: clk-s-a0-pll { #clock-cells = <1>; compatible = "st,clkgena-plls-c65"; - clocks = <&CLK_SYSIN>; + clocks = <&clk_sysin>; - clock-output-names = "CLK_S_A0_PLL0_HS", - "CLK_S_A0_PLL0_LS", - "CLK_S_A0_PLL1"; + clock-output-names = "clk-s-a0-pll0-hs", + "clk-s-a0-pll0-ls", + "clk-s-a0-pll1"; }; }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-prediv.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-prediv.txt index 566c9d79ed32..604766c2619e 100644 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen-prediv.txt +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-prediv.txt @@ -20,17 +20,17 @@ Required properties: Example: - clockgenA@fd345000 { + clockgen-a@fd345000 { reg = <0xfd345000 0xb50>; - CLK_M_A2_OSC_PREDIV: CLK_M_A2_OSC_PREDIV { + clk_m_a2_osc_prediv: clk-m-a2-osc-prediv { #clock-cells = <0>; compatible = "st,clkgena-prediv-c32", "st,clkgena-prediv"; - clocks = <&CLK_SYSIN>; + clocks = <&clk_sysin>; - clock-output-names = "CLK_M_A2_OSC_PREDIV"; + clock-output-names = "clk-m-a2-osc-prediv"; }; }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-vcc.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-vcc.txt index 4e3ff28b04c3..109b3eddcb17 100644 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen-vcc.txt +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-vcc.txt @@ -32,22 +32,30 @@ Required properties: Example: - CLOCKGEN_C_VCC: CLOCKGEN_C_VCC { + clockgen_c_vcc: clockgen-c-vcc@0xfe8308ac { #clock-cells = <1>; compatible = "st,stih416-clkgenc", "st,clkgen-vcc"; reg = <0xfe8308ac 12>; - clocks = <&CLK_S_VCC_HD>, <&CLOCKGEN_C 1>, - <&CLK_S_TMDS_FROMPHY>, <&CLOCKGEN_C 2>; - - clock-output-names = - "CLK_S_PIX_HDMI", "CLK_S_PIX_DVO", - "CLK_S_OUT_DVO", "CLK_S_PIX_HD", - "CLK_S_HDDAC", "CLK_S_DENC", - "CLK_S_SDDAC", "CLK_S_PIX_MAIN", - "CLK_S_PIX_AUX", "CLK_S_STFE_FRC_0", - "CLK_S_REF_MCRU", "CLK_S_SLAVE_MCRU", - "CLK_S_TMDS_HDMI", "CLK_S_HDMI_REJECT_PLL", - "CLK_S_THSENS"; + clocks = <&clk_s_vcc_hd>, + <&clockgen_c 1>, + <&clk_s_tmds_fromphy>, + <&clockgen_c 2>; + + clock-output-names = "clk-s-pix-hdmi", + "clk-s-pix-dvo", + "clk-s-out-dvo", + "clk-s-pix-hd", + "clk-s-hddac", + "clk-s-denc", + "clk-s-sddac", + "clk-s-pix-main", + "clk-s-pix-aux", + "clk-s-stfe-frc-0", + "clk-s-ref-mcru", + "clk-s-slave-mcru", + "clk-s-tmds-hdmi", + "clk-s-hdmi-reject-pll", + "clk-s-thsens"; }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen.txt index 49ec5ae18b5b..78978f1f5158 100644 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen.txt +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen.txt @@ -24,60 +24,77 @@ address is common of all subnode. quadfs_node { ... }; + + mux_node { + ... + }; + + vcc_node { + ... + }; + + flexgen_node { + ... + }; ... }; This binding uses the common clock binding[1]. -Each subnode should use the binding discribe in [2]..[4] +Each subnode should use the binding discribe in [2]..[7] [1] Documentation/devicetree/bindings/clock/clock-bindings.txt -[2] Documentation/devicetree/bindings/clock/st,quadfs.txt -[3] Documentation/devicetree/bindings/clock/st,quadfs.txt -[4] Documentation/devicetree/bindings/clock/st,quadfs.txt +[2] Documentation/devicetree/bindings/clock/st,clkgen-divmux.txt +[3] Documentation/devicetree/bindings/clock/st,clkgen-mux.txt +[4] Documentation/devicetree/bindings/clock/st,clkgen-pll.txt +[5] Documentation/devicetree/bindings/clock/st,clkgen-prediv.txt +[6] Documentation/devicetree/bindings/clock/st,vcc.txt +[7] Documentation/devicetree/bindings/clock/st,quadfs.txt +[8] Documentation/devicetree/bindings/clock/st,flexgen.txt + Required properties: - reg : A Base address and length of the register set. Example: - clockgenA@fee62000 { + clockgen-a@fee62000 { reg = <0xfee62000 0xb48>; - CLK_S_A0_PLL: CLK_S_A0_PLL { + clk_s_a0_pll: clk-s-a0-pll { #clock-cells = <1>; compatible = "st,clkgena-plls-c65"; - clocks = <&CLK_SYSIN>; + clocks = <&clk-sysin>; - clock-output-names = "CLK_S_A0_PLL0_HS", - "CLK_S_A0_PLL0_LS", - "CLK_S_A0_PLL1"; + clock-output-names = "clk-s-a0-pll0-hs", + "clk-s-a0-pll0-ls", + "clk-s-a0-pll1"; }; - CLK_S_A0_OSC_PREDIV: CLK_S_A0_OSC_PREDIV { + clk_s_a0_osc_prediv: clk-s-a0-osc-prediv { #clock-cells = <0>; compatible = "st,clkgena-prediv-c65", "st,clkgena-prediv"; - clocks = <&CLK_SYSIN>; + clocks = <&clk_sysin>; - clock-output-names = "CLK_S_A0_OSC_PREDIV"; + clock-output-names = "clk-s-a0-osc-prediv"; }; - CLK_S_A0_HS: CLK_S_A0_HS { + clk_s_a0_hs: clk-s-a0-hs { #clock-cells = <1>; compatible = "st,clkgena-divmux-c65-hs", "st,clkgena-divmux"; - clocks = <&CLK_S_A0_OSC_PREDIV>, - <&CLK_S_A0_PLL 0>, /* PLL0 HS */ - <&CLK_S_A0_PLL 2>; /* PLL1 */ + clocks = <&clk-s_a0_osc_prediv>, + <&clk-s_a0_pll 0>, /* pll0 hs */ + <&clk-s_a0_pll 2>; /* pll1 */ - clock-output-names = "CLK_S_FDMA_0", - "CLK_S_FDMA_1", - ""; /* CLK_S_JIT_SENSE */ - /* Fourth output unused */ + clock-output-names = "clk-s-fdma-0", + "clk-s-fdma-1", + ""; /* clk-s-jit-sense */ + /* fourth output unused */ }; }; diff --git a/Documentation/devicetree/bindings/clock/st/st,flexgen.txt b/Documentation/devicetree/bindings/clock/st/st,flexgen.txt new file mode 100644 index 000000000000..1d3ace088172 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,flexgen.txt @@ -0,0 +1,119 @@ +Binding for a type of flexgen structure found on certain +STMicroelectronics consumer electronics SoC devices + +This structure includes: +- a clock cross bar (represented by a mux element) +- a pre and final dividers (represented by a divider and gate elements) + +Flexgen structure is a part of Clockgen[1]. + +Please find an example below: + + Clockgen block diagram + ------------------------------------------------------------------- + | Flexgen stucture | + | --------------------------------------------- | + | | ------- -------- -------- | | +clk_sysin | | | | | | | | | +---|-----------------|-->| | | | | | | | + | | | | | | | | | | | + | | ------- | | | |Pre | |Final | | | + | | |PLL0 | | | | |Dividers| |Dividers| | | + | |->| | | | | | x32 | | x32 | | | + | | | odf_0|----|-->| | | | | | | | + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | ------- | | | | | | | | | + | | | | | | | | | | | + | | ------- | | Clock | | | | | | | + | | |PLL1 | | | | | | | | | | + | |->| | | | Cross | | | | | | | + | | | odf_0|----|-->| | | | | | CLK_DIV[31:0] + | | | | | | Bar |====>| |====>| |===|=========> + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | ------- | | | | | | | | | + | | | | | | | | | | | + | | ------- | | | | | | | | | + | | |QUADFS | | | | | | | | | | + | |->| ch0|----|-->| | | | | | | | + | | | | | | | | | | | | + | | ch1|----|-->| | | | | | | | + | | | | | | | | | | | | + | | ch2|----|-->| | | DIV | | DIV | | | + | | | | | | | 1 to | | 1 to | | | + | | ch3|----|-->| | | 1024 | | 64 | | | + | ------- | | | | | | | | | + | | ------- -------- -------- | | + | -------------------------------------------- | + | | + ------------------------------------------------------------------- + +This binding uses the common clock binding[2]. + +[1] Documentation/devicetree/bindings/clock/st/st,clkgen.txt +[2] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be: + "st,flexgen" + +- #clock-cells : from common clock binding; shall be set to 1 (multiple clock + outputs). + +- clocks : must be set to the parent's phandle. it's could be output clocks of + a quadsfs or/and a pll or/and clk_sysin (up to 7 clocks) + +- clock-output-names : List of strings used to name the clock outputs. + +Example: + + clk_s_c0_flexgen: clk-s-c0-flexgen { + + #clock-cells = <1>; + compatible = "st,flexgen"; + + clocks = <&clk_s_c0_pll0 0>, + <&clk_s_c0_pll1 0>, + <&clk_s_c0_quadfs 0>, + <&clk_s_c0_quadfs 1>, + <&clk_s_c0_quadfs 2>, + <&clk_s_c0_quadfs 3>, + <&clk_sysin>; + + clock-output-names = "clk-icn-gpu", + "clk-fdma", + "clk-nand", + "clk-hva", + "clk-proc-stfe", + "clk-proc-tp", + "clk-rx-icn-dmu", + "clk-rx-icn-hva", + "clk-icn-cpu", + "clk-tx-icn-dmu", + "clk-mmc-0", + "clk-mmc-1", + "clk-jpegdec", + "clk-ext2fa9", + "clk-ic-bdisp-0", + "clk-ic-bdisp-1", + "clk-pp-dmu", + "clk-vid-dmu", + "clk-dss-lpc", + "clk-st231-aud-0", + "clk-st231-gp-1", + "clk-st231-dmu", + "clk-icn-lmi", + "clk-tx-icn-disp-1", + "clk-icn-sbc", + "clk-stfe-frc2", + "clk-eth-phy", + "clk-eth-ref-phyclk", + "clk-flash-promip", + "clk-main-disp", + "clk-aux-disp", + "clk-compo-dvp"; + }; diff --git a/Documentation/devicetree/bindings/clock/st/st,quadfs.txt b/Documentation/devicetree/bindings/clock/st/st,quadfs.txt index ec86d62ca283..cedeb9cc8208 100644 --- a/Documentation/devicetree/bindings/clock/st/st,quadfs.txt +++ b/Documentation/devicetree/bindings/clock/st/st,quadfs.txt @@ -15,6 +15,9 @@ Required properties: "st,stih416-quadfs432", "st,quadfs" "st,stih416-quadfs660-E", "st,quadfs" "st,stih416-quadfs660-F", "st,quadfs" + "st,stih407-quadfs660-C", "st,quadfs" + "st,stih407-quadfs660-D", "st,quadfs" + - #clock-cells : from common clock binding; shall be set to 1. @@ -32,14 +35,14 @@ Required properties: Example: - CLOCKGEN_E: CLOCKGEN_E { + clockgen_e: clockgen-e@fd3208bc { #clock-cells = <1>; compatible = "st,stih416-quadfs660-E", "st,quadfs"; reg = <0xfd3208bc 0xB0>; - clocks = <&CLK_SYSIN>; - clock-output-names = "CLK_M_PIX_MDTP_0", - "CLK_M_PIX_MDTP_1", - "CLK_M_PIX_MDTP_2", - "CLK_M_MPELPC"; + clocks = <&clk_sysin>; + clock-output-names = "clk-m-pix-mdtp-0", + "clk-m-pix-mdtp-1", + "clk-m-pix-mdtp-2", + "clk-m-mpelpc"; }; diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt index b9ec668bfe62..d3a5c3c6d677 100644 --- a/Documentation/devicetree/bindings/clock/sunxi.txt +++ b/Documentation/devicetree/bindings/clock/sunxi.txt @@ -9,11 +9,13 @@ Required properties: "allwinner,sun4i-a10-osc-clk" - for a gatable oscillator "allwinner,sun4i-a10-pll1-clk" - for the main PLL clock and PLL4 "allwinner,sun6i-a31-pll1-clk" - for the main PLL clock on A31 + "allwinner,sun8i-a23-pll1-clk" - for the main PLL clock on A23 "allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock "allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock "allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31 "allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock "allwinner,sun4i-a10-axi-clk" - for the AXI clock + "allwinner,sun8i-a23-axi-clk" - for the AXI clock on A23 "allwinner,sun4i-a10-axi-gates-clk" - for the AXI gates "allwinner,sun4i-a10-ahb-clk" - for the AHB clock "allwinner,sun4i-a10-ahb-gates-clk" - for the AHB gates on A10 @@ -23,13 +25,16 @@ Required properties: "allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31 "allwinner,sun6i-a31-ahb1-mux-clk" - for the AHB1 multiplexer on A31 "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31 + "allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23 "allwinner,sun4i-a10-apb0-clk" - for the APB0 clock "allwinner,sun6i-a31-apb0-clk" - for the APB0 clock on A31 + "allwinner,sun8i-a23-apb0-clk" - for the APB0 clock on A23 "allwinner,sun4i-a10-apb0-gates-clk" - for the APB0 gates on A10 "allwinner,sun5i-a13-apb0-gates-clk" - for the APB0 gates on A13 "allwinner,sun5i-a10s-apb0-gates-clk" - for the APB0 gates on A10s "allwinner,sun6i-a31-apb0-gates-clk" - for the APB0 gates on A31 "allwinner,sun7i-a20-apb0-gates-clk" - for the APB0 gates on A20 + "allwinner,sun8i-a23-apb0-gates-clk" - for the APB0 gates on A23 "allwinner,sun4i-a10-apb1-clk" - for the APB1 clock "allwinner,sun4i-a10-apb1-mux-clk" - for the APB1 clock muxing "allwinner,sun4i-a10-apb1-gates-clk" - for the APB1 gates on A10 @@ -37,8 +42,10 @@ Required properties: "allwinner,sun5i-a10s-apb1-gates-clk" - for the APB1 gates on A10s "allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31 "allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20 + "allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23 "allwinner,sun6i-a31-apb2-div-clk" - for the APB2 gates on A31 "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31 + "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23 "allwinner,sun4i-a10-mod0-clk" - for the module 0 family of clocks "allwinner,sun7i-a20-out-clk" - for the external output clocks "allwinner,sun7i-a20-gmac-clk" - for the GMAC clock module on A20/A31 diff --git a/Documentation/devicetree/bindings/crypto/amd-ccp.txt b/Documentation/devicetree/bindings/crypto/amd-ccp.txt new file mode 100644 index 000000000000..8c61183b41e0 --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/amd-ccp.txt @@ -0,0 +1,19 @@ +* AMD Cryptographic Coprocessor driver (ccp) + +Required properties: +- compatible: Should be "amd,ccp-seattle-v1a" +- reg: Address and length of the register set for the device +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the CCP interrupt + +Optional properties: +- dma-coherent: Present if dma operations are coherent + +Example: + ccp@e0100000 { + compatible = "amd,ccp-seattle-v1a"; + reg = <0 0xe0100000 0 0x10000>; + interrupt-parent = <&gic>; + interrupts = <0 3 4>; + }; diff --git a/Documentation/devicetree/bindings/crypto/qcom-qce.txt b/Documentation/devicetree/bindings/crypto/qcom-qce.txt new file mode 100644 index 000000000000..fdd53b184ba8 --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/qcom-qce.txt @@ -0,0 +1,25 @@ +Qualcomm crypto engine driver + +Required properties: + +- compatible : should be "qcom,crypto-v5.1" +- reg : specifies base physical address and size of the registers map +- clocks : phandle to clock-controller plus clock-specifier pair +- clock-names : "iface" clocks register interface + "bus" clocks data transfer interface + "core" clocks rest of the crypto block +- dmas : DMA specifiers for tx and rx dma channels. For more see + Documentation/devicetree/bindings/dma/dma.txt +- dma-names : DMA request names should be "rx" and "tx" + +Example: + crypto@fd45a000 { + compatible = "qcom,crypto-v5.1"; + reg = <0xfd45a000 0x6000>; + clocks = <&gcc GCC_CE2_AHB_CLK>, + <&gcc GCC_CE2_AXI_CLK>, + <&gcc GCC_CE2_CLK>; + clock-names = "iface", "bus", "core"; + dmas = <&cryptobam 2>, <&cryptobam 3>; + dma-names = "rx", "tx"; + }; diff --git a/Documentation/devicetree/bindings/extcon/extcon-sm5502.txt b/Documentation/devicetree/bindings/extcon/extcon-sm5502.txt new file mode 100644 index 000000000000..4ecda224955f --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/extcon-sm5502.txt @@ -0,0 +1,23 @@ + +* SM5502 MUIC (Micro-USB Interface Controller) device + +The Silicon Mitus SM5502 is a MUIC (Micro-USB Interface Controller) device +which can detect the state of external accessory when external accessory is +attached or detached and button is pressed or released. It is interfaced to +the host controller using an I2C interface. + +Required properties: +- compatible: Should be "siliconmitus,sm5502-muic" +- reg: Specifies the I2C slave address of the MUIC block. It should be 0x25 +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from sm5502 are delivered to. +- interrupts: Interrupt specifiers for detection interrupt sources. + +Example: + + sm5502@25 { + compatible = "siliconmitus,sm5502-muic"; + interrupt-parent = <&gpx1>; + interrupts = <5 0>; + reg = <0x25>; + }; diff --git a/Documentation/devicetree/bindings/hwmon/ibmpowernv.txt b/Documentation/devicetree/bindings/hwmon/ibmpowernv.txt new file mode 100644 index 000000000000..f93242be60a1 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/ibmpowernv.txt @@ -0,0 +1,23 @@ +IBM POWERNV platform sensors +---------------------------- + +Required node properties: +- compatible: must be one of + "ibm,opal-sensor-cooling-fan" + "ibm,opal-sensor-amb-temp" + "ibm,opal-sensor-power-supply" + "ibm,opal-sensor-power" +- sensor-id: an opaque id provided by the firmware to the kernel, identifies a + given sensor and its attribute data + +Example sensors node: + +cooling-fan#8-data { + sensor-id = <0x7052107>; + compatible = "ibm,opal-sensor-cooling-fan"; +}; + +amb-temp#1-thrs { + sensor-id = <0x5096000>; + compatible = "ibm,opal-sensor-amb-temp"; +}; diff --git a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt index b117b2e9e1a7..2391e5c41999 100644 --- a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt +++ b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt @@ -3,6 +3,7 @@ NTC Thermistor hwmon sensors Requires node properties: - "compatible" value : one of + "epcos,b57330v2103" "murata,ncp15wb473" "murata,ncp18wb473" "murata,ncp21wb473" diff --git a/Documentation/devicetree/bindings/hwmon/pwm-fan.txt b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt new file mode 100644 index 000000000000..610757ce4492 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt @@ -0,0 +1,12 @@ +Bindings for a fan connected to the PWM lines + +Required properties: +- compatible : "pwm-fan" +- pwms : the PWM that is used to control the PWM fan + +Example: + pwm-fan { + compatible = "pwm-fan"; + status = "okay"; + pwms = <&pwm 0 10000 0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index bef86e57c388..37803eb5521e 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -50,6 +50,7 @@ epson,rx8581 I2C-BUS INTERFACE REAL TIME CLOCK MODULE fsl,mag3110 MAG3110: Xtrinsic High Accuracy, 3D Magnetometer fsl,mc13892 MC13892: Power Management Integrated Circuit (PMIC) for i.MX35/51 fsl,mma8450 MMA8450Q: Xtrinsic Low-power, 3-axis Xtrinsic Accelerometer +fsl,mma8452 MMA8452Q: 3-axis 12-bit / 8-bit Digital Accelerometer fsl,mpr121 MPR121: Proximity Capacitive Touch Sensor Controller fsl,sgtl5000 SGTL5000: Ultra Low-Power Audio Codec gmt,g751 G751: Digital Temperature Sensor and Thermal Watchdog with Two-Wire Interface @@ -83,5 +84,6 @@ stm,m41t80 M41T80 - SERIAL ACCESS RTC WITH ALARMS taos,tsl2550 Ambient Light Sensor with SMBUS/Two Wire Serial Interface ti,tsc2003 I2C Touch-Screen Controller ti,tmp102 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface +ti,tmp103 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface ti,tmp275 Digital Temperature Sensor winbond,wpct301 i2c trusted platform module (TPM) diff --git a/Documentation/devicetree/bindings/iio/adc/max1027-adc.txt b/Documentation/devicetree/bindings/iio/adc/max1027-adc.txt new file mode 100644 index 000000000000..a8770cc6bcad --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/max1027-adc.txt @@ -0,0 +1,22 @@ +* Maxim 1027/1029/1031 Analog to Digital Converter (ADC) + +Required properties: + - compatible: Should be "maxim,max1027" or "maxim,max1029" or "maxim,max1031" + - reg: SPI chip select number for the device + - interrupt-parent: phandle to the parent interrupt controller + see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + - interrupts: IRQ line for the ADC + see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + +Recommended properties: +- spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: +adc@0 { + compatible = "maxim,max1027"; + reg = <0>; + interrupt-parent = <&gpio5>; + interrupts = <15 IRQ_TYPE_EDGE_RISING>; + spi-max-frequency = <1000000>; +}; diff --git a/Documentation/devicetree/bindings/iio/magnetometer/hmc5843.txt b/Documentation/devicetree/bindings/iio/magnetometer/hmc5843.txt index 90d5f34db04e..8e191eef014e 100644 --- a/Documentation/devicetree/bindings/iio/magnetometer/hmc5843.txt +++ b/Documentation/devicetree/bindings/iio/magnetometer/hmc5843.txt @@ -3,6 +3,10 @@ Required properties: - compatible : should be "honeywell,hmc5843" + Other models which are supported with driver are: + "honeywell,hmc5883" + "honeywell,hmc5883l" + "honeywell,hmc5983" - reg : the I2C address of the magnetometer - typically 0x1e Optional properties: diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt new file mode 100644 index 000000000000..a7a0a15913ad --- /dev/null +++ b/Documentation/devicetree/bindings/iio/st-sensors.txt @@ -0,0 +1,54 @@ +STMicroelectronics MEMS sensors + +The STMicroelectronics sensor devices are pretty straight-forward I2C or +SPI devices, all sharing the same device tree descriptions no matter what +type of sensor it is. + +Required properties: +- compatible: see the list of valid compatible strings below +- reg: the I2C or SPI address the device will respond to + +Optional properties: +- vdd-supply: an optional regulator that needs to be on to provide VDD + power to the sensor. +- vddio-supply: an optional regulator that needs to be on to provide the + VDD IO power to the sensor. +- st,drdy-int-pin: the pin on the package that will be used to signal + "data ready" (valid values: 1 or 2). This property is not configurable + on all sensors. + +Sensors may also have applicable pin control settings, those use the +standard bindings from pinctrl/pinctrl-bindings.txt. + +Valid compatible strings: + +Accelerometers: +- st,lsm303dlh-accel +- st,lsm303dlhc-accel +- st,lis3dh-accel +- st,lsm330d-accel +- st,lsm330dl-accel +- st,lsm330dlc-accel +- st,lis331dlh-accel +- st,lsm303dl-accel +- st,lsm303dlm-accel +- st,lsm330-accel + +Gyroscopes: +- st,l3g4200d-gyro +- st,lsm330d-gyro +- st,lsm330dl-gyro +- st,lsm330dlc-gyro +- st,l3gd20-gyro +- st,l3g4is-gyro +- st,lsm330-gyro + +Magnetometers: +- st,lsm303dlhc-magn +- st,lsm303dlm-magn +- st,lis3mdl-magn + +Pressure sensors: +- st,lps001wp-press +- st,lps25h-press +- st,lps331ap-press diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu.txt b/Documentation/devicetree/bindings/iommu/arm,smmu.txt index f284b99402bc..2d0f7cd867ea 100644 --- a/Documentation/devicetree/bindings/iommu/arm,smmu.txt +++ b/Documentation/devicetree/bindings/iommu/arm,smmu.txt @@ -42,12 +42,6 @@ conditions. ** System MMU optional properties: -- smmu-parent : When multiple SMMUs are chained together, this - property can be used to provide a phandle to the - parent SMMU (that is the next SMMU on the path going - from the mmu-masters towards memory) node for this - SMMU. - - calxeda,smmu-secure-config-access : Enable proper handling of buggy implementations that always use secure access to SMMU configuration registers. In this case non-secure diff --git a/Documentation/devicetree/bindings/iommu/iommu.txt b/Documentation/devicetree/bindings/iommu/iommu.txt new file mode 100644 index 000000000000..5a8b4624defc --- /dev/null +++ b/Documentation/devicetree/bindings/iommu/iommu.txt @@ -0,0 +1,182 @@ +This document describes the generic device tree binding for IOMMUs and their +master(s). + + +IOMMU device node: +================== + +An IOMMU can provide the following services: + +* Remap address space to allow devices to access physical memory ranges that + they otherwise wouldn't be capable of accessing. + + Example: 32-bit DMA to 64-bit physical addresses + +* Implement scatter-gather at page level granularity so that the device does + not have to. + +* Provide system protection against "rogue" DMA by forcing all accesses to go + through the IOMMU and faulting when encountering accesses to unmapped + address regions. + +* Provide address space isolation between multiple contexts. + + Example: Virtualization + +Device nodes compatible with this binding represent hardware with some of the +above capabilities. + +IOMMUs can be single-master or multiple-master. Single-master IOMMU devices +typically have a fixed association to the master device, whereas multiple- +master IOMMU devices can translate accesses from more than one master. + +The device tree node of the IOMMU device's parent bus must contain a valid +"dma-ranges" property that describes how the physical address space of the +IOMMU maps to memory. An empty "dma-ranges" property means that there is a +1:1 mapping from IOMMU to memory. + +Required properties: +-------------------- +- #iommu-cells: The number of cells in an IOMMU specifier needed to encode an + address. + +The meaning of the IOMMU specifier is defined by the device tree binding of +the specific IOMMU. Below are a few examples of typical use-cases: + +- #iommu-cells = <0>: Single master IOMMU devices are not configurable and + therefore no additional information needs to be encoded in the specifier. + This may also apply to multiple master IOMMU devices that do not allow the + association of masters to be configured. Note that an IOMMU can by design + be multi-master yet only expose a single master in a given configuration. + In such cases the number of cells will usually be 1 as in the next case. +- #iommu-cells = <1>: Multiple master IOMMU devices may need to be configured + in order to enable translation for a given master. In such cases the single + address cell corresponds to the master device's ID. In some cases more than + one cell can be required to represent a single master ID. +- #iommu-cells = <4>: Some IOMMU devices allow the DMA window for masters to + be configured. The first cell of the address in this may contain the master + device's ID for example, while the second cell could contain the start of + the DMA window for the given device. The length of the DMA window is given + by the third and fourth cells. + +Note that these are merely examples and real-world use-cases may use different +definitions to represent their individual needs. Always refer to the specific +IOMMU binding for the exact meaning of the cells that make up the specifier. + + +IOMMU master node: +================== + +Devices that access memory through an IOMMU are called masters. A device can +have multiple master interfaces (to one or more IOMMU devices). + +Required properties: +-------------------- +- iommus: A list of phandle and IOMMU specifier pairs that describe the IOMMU + master interfaces of the device. One entry in the list describes one master + interface of the device. + +When an "iommus" property is specified in a device tree node, the IOMMU will +be used for address translation. If a "dma-ranges" property exists in the +device's parent node it will be ignored. An exception to this rule is if the +referenced IOMMU is disabled, in which case the "dma-ranges" property of the +parent shall take effect. Note that merely disabling a device tree node does +not guarantee that the IOMMU is really disabled since the hardware may not +have a means to turn off translation. But it is invalid in such cases to +disable the IOMMU's device tree node in the first place because it would +prevent any driver from properly setting up the translations. + + +Notes: +====== + +One possible extension to the above is to use an "iommus" property along with +a "dma-ranges" property in a bus device node (such as PCI host bridges). This +can be useful to describe how children on the bus relate to the IOMMU if they +are not explicitly listed in the device tree (e.g. PCI devices). However, the +requirements of that use-case haven't been fully determined yet. Implementing +this is therefore not recommended without further discussion and extension of +this binding. + + +Examples: +========= + +Single-master IOMMU: +-------------------- + + iommu { + #iommu-cells = <0>; + }; + + master { + iommus = <&{/iommu}>; + }; + +Multiple-master IOMMU with fixed associations: +---------------------------------------------- + + /* multiple-master IOMMU */ + iommu { + /* + * Masters are statically associated with this IOMMU and share + * the same address translations because the IOMMU does not + * have sufficient information to distinguish between masters. + * + * Consequently address translation is always on or off for + * all masters at any given point in time. + */ + #iommu-cells = <0>; + }; + + /* static association with IOMMU */ + master@1 { + reg = <1>; + iommus = <&{/iommu}>; + }; + + /* static association with IOMMU */ + master@2 { + reg = <2>; + iommus = <&{/iommu}>; + }; + +Multiple-master IOMMU: +---------------------- + + iommu { + /* the specifier represents the ID of the master */ + #iommu-cells = <1>; + }; + + master@1 { + /* device has master ID 42 in the IOMMU */ + iommus = <&{/iommu} 42>; + }; + + master@2 { + /* device has master IDs 23 and 24 in the IOMMU */ + iommus = <&{/iommu} 23>, <&{/iommu} 24>; + }; + +Multiple-master IOMMU with configurable DMA window: +--------------------------------------------------- + + / { + iommu { + /* + * One cell for the master ID and one cell for the + * address of the DMA window. The length of the DMA + * window is encoded in two cells. + * + * The DMA window is the range addressable by the + * master (i.e. the I/O virtual address space). + */ + #iommu-cells = <4>; + }; + + master { + /* master ID 42, 4 GiB DMA window starting at 0 */ + iommus = <&{/iommu} 42 0 0x1 0x0>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/berlin-sata-phy.txt b/Documentation/devicetree/bindings/phy/berlin-sata-phy.txt new file mode 100644 index 000000000000..88f8c23384c0 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/berlin-sata-phy.txt @@ -0,0 +1,34 @@ +Berlin SATA PHY +--------------- + +Required properties: +- compatible: should be "marvell,berlin2q-sata-phy" +- address-cells: should be 1 +- size-cells: should be 0 +- phy-cells: from the generic PHY bindings, must be 1 +- reg: address and length of the register +- clocks: reference to the clock entry + +Sub-nodes: +Each PHY should be represented as a sub-node. + +Sub-nodes required properties: +- reg: the PHY number + +Example: + sata_phy: phy@f7e900a0 { + compatible = "marvell,berlin2q-sata-phy"; + reg = <0xf7e900a0 0x200>; + clocks = <&chip CLKID_SATA>; + #address-cells = <1>; + #size-cells = <0>; + #phy-cells = <1>; + + sata-phy@0 { + reg = <0>; + }; + + sata-phy@1 { + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/hix5hd2-phy.txt b/Documentation/devicetree/bindings/phy/hix5hd2-phy.txt new file mode 100644 index 000000000000..296168b74d24 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/hix5hd2-phy.txt @@ -0,0 +1,22 @@ +Hisilicon hix5hd2 SATA PHY +----------------------- + +Required properties: +- compatible: should be "hisilicon,hix5hd2-sata-phy" +- reg: offset and length of the PHY registers +- #phy-cells: must be 0 +Refer to phy/phy-bindings.txt for the generic PHY binding properties + +Optional Properties: +- hisilicon,peripheral-syscon: phandle of syscon used to control peripheral. +- hisilicon,power-reg: offset and bit number within peripheral-syscon, + register of controlling sata power supply. + +Example: + sata_phy: phy@f9900000 { + compatible = "hisilicon,hix5hd2-sata-phy"; + reg = <0xf9900000 0x10000>; + #phy-cells = <0>; + hisilicon,peripheral-syscon = <&peripheral_ctrl>; + hisilicon,power-reg = <0x8 10>; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-bindings.txt b/Documentation/devicetree/bindings/phy/phy-bindings.txt index 8ae844fc0c60..2aa1840200ed 100644 --- a/Documentation/devicetree/bindings/phy/phy-bindings.txt +++ b/Documentation/devicetree/bindings/phy/phy-bindings.txt @@ -10,6 +10,10 @@ Required Properties: provider can use the values in cells to find the appropriate PHY. +Optional Properties: +phy-supply: Phandle to a regulator that provides power to the PHY. This + regulator will be managed during the PHY power on/off sequence. + For example: phys: phy { diff --git a/Documentation/devicetree/bindings/phy/phy-miphy365x.txt b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt new file mode 100644 index 000000000000..42c880886cf7 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt @@ -0,0 +1,76 @@ +STMicroelectronics STi MIPHY365x PHY binding +============================================ + +This binding describes a miphy device that is used to control PHY hardware +for SATA and PCIe. + +Required properties (controller (parent) node): +- compatible : Should be "st,miphy365x-phy" +- st,syscfg : Should be a phandle of the system configuration register group + which contain the SATA, PCIe mode setting bits + +Required nodes : A sub-node is required for each channel the controller + provides. Address range information including the usual + 'reg' and 'reg-names' properties are used inside these + nodes to describe the controller's topology. These nodes + are translated by the driver's .xlate() function. + +Required properties (port (child) node): +- #phy-cells : Should be 1 (See second example) + Cell after port phandle is device type from: + - MIPHY_TYPE_SATA + - MIPHY_TYPE_PCI +- reg : Address and length of register sets for each device in + "reg-names" +- reg-names : The names of the register addresses corresponding to the + registers filled in "reg": + - sata: For SATA devices + - pcie: For PCIe devices + - syscfg: To specify the syscfg based config register + +Optional properties (port (child) node): +- st,sata-gen : Generation of locally attached SATA IP. Expected values + are {1,2,3). If not supplied generation 1 hardware will + be expected +- st,pcie-tx-pol-inv : Bool property to invert the polarity PCIe Tx (Txn/Txp) +- st,sata-tx-pol-inv : Bool property to invert the polarity SATA Tx (Txn/Txp) + +Example: + + miphy365x_phy: miphy365x@fe382000 { + compatible = "st,miphy365x-phy"; + st,syscfg = <&syscfg_rear>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + phy_port0: port@fe382000 { + reg = <0xfe382000 0x100>, <0xfe394000 0x100>, <0x824 0x4>; + reg-names = "sata", "pcie", "syscfg"; + #phy-cells = <1>; + st,sata-gen = <3>; + }; + + phy_port1: port@fe38a000 { + reg = <0xfe38a000 0x100>, <0xfe804000 0x100>, <0x828 0x4>;; + reg-names = "sata", "pcie", "syscfg"; + #phy-cells = <1>; + st,pcie-tx-pol-inv; + }; + }; + +Specifying phy control of devices +================================= + +Device nodes should specify the configuration required in their "phys" +property, containing a phandle to the phy port node and a device type. + +Example: + +#include <dt-bindings/phy/phy-miphy365x.h> + + sata0: sata@fe380000 { + ... + phys = <&phy_port0 MIPHY_TYPE_SATA>; + ... + }; diff --git a/Documentation/devicetree/bindings/phy/qcom-apq8064-sata-phy.txt b/Documentation/devicetree/bindings/phy/qcom-apq8064-sata-phy.txt new file mode 100644 index 000000000000..952f6c96bab9 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom-apq8064-sata-phy.txt @@ -0,0 +1,24 @@ +Qualcomm APQ8064 SATA PHY Controller +------------------------------------ + +SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers. +Each SATA PHY controller should have its own node. + +Required properties: +- compatible: compatible list, contains "qcom,apq8064-sata-phy". +- reg: offset and length of the SATA PHY register set; +- #phy-cells: must be zero +- clocks: a list of phandles and clock-specifier pairs, one for each entry in + clock-names. +- clock-names: must be "cfg" for phy config clock. + +Example: + sata_phy: sata-phy@1b400000 { + compatible = "qcom,apq8064-sata-phy"; + reg = <0x1b400000 0x200>; + + clocks = <&gcc SATA_PHY_CFG_CLK>; + clock-names = "cfg"; + + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom-ipq806x-sata-phy.txt b/Documentation/devicetree/bindings/phy/qcom-ipq806x-sata-phy.txt new file mode 100644 index 000000000000..76bfbd056202 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom-ipq806x-sata-phy.txt @@ -0,0 +1,23 @@ +Qualcomm IPQ806x SATA PHY Controller +------------------------------------ + +SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers. +Each SATA PHY controller should have its own node. + +Required properties: +- compatible: compatible list, contains "qcom,ipq806x-sata-phy" +- reg: offset and length of the SATA PHY register set; +- #phy-cells: must be zero +- clocks: must be exactly one entry +- clock-names: must be "cfg" + +Example: + sata_phy: sata-phy@1b400000 { + compatible = "qcom,ipq806x-sata-phy"; + reg = <0x1b400000 0x200>; + + clocks = <&gcc SATA_PHY_CFG_CLK>; + clock-names = "cfg"; + + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt index 2049261d8c31..6099a5c94283 100644 --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt @@ -26,6 +26,7 @@ Samsung S5P/EXYNOS SoC series USB PHY Required properties: - compatible : should be one of the listed compatibles: + - "samsung,exynos3250-usb2-phy" - "samsung,exynos4210-usb2-phy" - "samsung,exynos4x12-usb2-phy" - "samsung,exynos5250-usb2-phy" @@ -46,6 +47,7 @@ and Exynos 4212) it is as follows: 1 - USB host ("host"), 2 - HSIC0 ("hsic0"), 3 - HSIC1 ("hsic1"), +Exynos3250 has only USB device phy available as phy 0. Exynos 4210 and Exynos 4212 use mode switching and require that mode switch register is supplied. diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt index 9ce458f32945..305e3df3d9b1 100644 --- a/Documentation/devicetree/bindings/phy/ti-phy.txt +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt @@ -9,15 +9,17 @@ Required properties: e.g. USB2_PHY on OMAP5. "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control e.g. USB3 PHY and SATA PHY on OMAP5. + "ti,control-phy-pcie" - for pcie to support external clock for pcie and to + set PCS delay value. + e.g. PCIE PHY in DRA7x "ti,control-phy-usb2-dra7" - if it has power down register like USB2 PHY on DRA7 platform. "ti,control-phy-usb2-am437" - if it has power down register like USB2 PHY on AM437 platform. - - reg : Address and length of the register set for the device. It contains - the address of "otghs_control" for control-phy-otghs or "power" register - for other types. - - reg-names: should be "otghs_control" control-phy-otghs and "power" for - other types. + - reg : register ranges as listed in the reg-names property + - reg-names: "otghs_control" for control-phy-otghs + "power", "pcie_pcs" and "control_sma" for control-phy-pcie + "power" for all other types omap_control_usb: omap-control-usb@4a002300 { compatible = "ti,control-phy-otghs"; @@ -56,8 +58,8 @@ usb2phy@4a0ad080 { TI PIPE3 PHY Required properties: - - compatible: Should be "ti,phy-usb3" or "ti,phy-pipe3-sata". - "ti,omap-usb3" is deprecated. + - compatible: Should be "ti,phy-usb3", "ti,phy-pipe3-sata" or + "ti,phy-pipe3-pcie. "ti,omap-usb3" is deprecated. - reg : Address and length of the register set for the device. - reg-names: The names of the register addresses corresponding to the registers filled in "reg". @@ -69,10 +71,17 @@ Required properties: * "wkupclk" - wakeup clock. * "sysclk" - system clock. * "refclk" - reference clock. + * "dpll_ref" - external dpll ref clk + * "dpll_ref_m2" - external dpll ref clk + * "phy-div" - divider for apll + * "div-clk" - apll clock Optional properties: - ctrl-module : phandle of the control module used by PHY driver to power on the PHY. + - id: If there are multiple instance of the same type, in order to + differentiate between each instance "id" can be used (e.g., multi-lane PCIe + PHY). If "id" is not provided, it is set to default value of '1'. This is usually a subnode of ocp2scp to which it is connected. diff --git a/Documentation/devicetree/bindings/serial/efm32-uart.txt b/Documentation/devicetree/bindings/serial/efm32-uart.txt index 3ca01336b837..8adbab268ca3 100644 --- a/Documentation/devicetree/bindings/serial/efm32-uart.txt +++ b/Documentation/devicetree/bindings/serial/efm32-uart.txt @@ -6,7 +6,7 @@ Required properties: - interrupts : Should contain uart interrupt Optional properties: -- efm32,location : Decides the location of the USART I/O pins. +- energymicro,location : Decides the location of the USART I/O pins. Allowed range : [0 .. 5] Default: 0 @@ -16,5 +16,5 @@ uart@0x4000c400 { compatible = "energymicro,efm32-uart"; reg = <0x4000c400 0x400>; interrupts = <15>; - efm32,location = <0>; + energymicro,location = <0>; }; diff --git a/Documentation/devicetree/bindings/serial/fsl-lpuart.txt b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt index a1d1205d8185..c95005efbcb8 100644 --- a/Documentation/devicetree/bindings/serial/fsl-lpuart.txt +++ b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt @@ -1,7 +1,11 @@ * Freescale low power universal asynchronous receiver/transmitter (lpuart) Required properties: -- compatible : Should be "fsl,<soc>-lpuart" +- compatible : + - "fsl,vf610-lpuart" for lpuart compatible with the one integrated + on Vybrid vf610 SoC with 8-bit register organization + - "fsl,ls1021a-lpuart" for lpuart compatible with the one integrated + on LS1021A SoC with 32-bit big-endian register organization - reg : Address and length of the register set for the device - interrupts : Should contain uart interrupt - clocks : phandle + clock specifier pairs, one for each entry in clock-names diff --git a/Documentation/devicetree/bindings/serial/samsung_uart.txt b/Documentation/devicetree/bindings/serial/samsung_uart.txt index 2c8a17cf5cb5..e85f37ec33f0 100644 --- a/Documentation/devicetree/bindings/serial/samsung_uart.txt +++ b/Documentation/devicetree/bindings/serial/samsung_uart.txt @@ -1,14 +1,58 @@ * Samsung's UART Controller -The Samsung's UART controller is used for interfacing SoC with serial communicaion -devices. +The Samsung's UART controller is used for interfacing SoC with serial +communicaion devices. Required properties: -- compatible: should be - - "samsung,exynos4210-uart", for UART's compatible with Exynos4210 uart ports. +- compatible: should be one of following: + - "samsung,exynos4210-uart" - Exynos4210 SoC, + - "samsung,s3c2410-uart" - compatible with ports present on S3C2410 SoC, + - "samsung,s3c2412-uart" - compatible with ports present on S3C2412 SoC, + - "samsung,s3c2440-uart" - compatible with ports present on S3C2440 SoC, + - "samsung,s3c6400-uart" - compatible with ports present on S3C6400 SoC, + - "samsung,s5pv210-uart" - compatible with ports present on S5PV210 SoC. - reg: base physical address of the controller and length of memory mapped region. -- interrupts: interrupt number to the cpu. The interrupt specifier format depends - on the interrupt controller parent. +- interrupts: a single interrupt signal to SoC interrupt controller, + according to interrupt bindings documentation [1]. + +- clock-names: input names of clocks used by the controller: + - "uart" - controller bus clock, + - "clk_uart_baudN" - Nth baud base clock input (N = 0, 1, ...), + according to SoC User's Manual (only N = 0 is allowedfor SoCs without + internal baud clock mux). +- clocks: phandles and specifiers for all clocks specified in "clock-names" + property, in the same order, according to clock bindings documentation [2]. + +[1] Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +[2] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Optional properties: +- samsung,uart-fifosize: The fifo size supported by the UART channel + +Note: Each Samsung UART should have an alias correctly numbered in the +"aliases" node, according to serialN format, where N is the port number +(non-negative decimal integer) as specified by User's Manual of respective +SoC. + +Example: + aliases { + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + }; + +Example: + uart1: serial@7f005400 { + compatible = "samsung,s3c6400-uart"; + reg = <0x7f005400 0x100>; + interrupt-parent = <&vic1>; + interrupts = <6>; + clock-names = "uart", "clk_uart_baud2", + "clk_uart_baud3"; + clocks = <&clocks PCLK_UART1>, <&clocks PCLK_UART1>, + <&clocks SCLK_UART>; + samsung,uart-fifosize = <16>; + }; diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt index f13f1c5be91c..7f76214f728a 100644 --- a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt +++ b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt @@ -4,9 +4,18 @@ Required properties: - compatible : "snps,dw-apb-uart" - reg : offset and length of the register set for the device. - interrupts : should contain uart interrupt. + +Clock handling: +The clock rate of the input clock needs to be supplied by one of - clock-frequency : the input clock frequency for the UART. +- clocks : phandle to the input clock + +The supplying peripheral clock can also be handled, needing a second property +- clock-names: tuple listing input clock names. + Required elements: "baudclk", "apb_pclk" Optional properties: +- resets : phandle to the parent reset controller. - reg-shift : quantity to shift the register offsets by. If this property is not present then the register offsets are not shifted. - reg-io-width : the size (in bytes) of the IO accesses that should be @@ -23,3 +32,26 @@ Example: reg-shift = <2>; reg-io-width = <4>; }; + +Example with one clock: + + uart@80230000 { + compatible = "snps,dw-apb-uart"; + reg = <0x80230000 0x100>; + clocks = <&baudclk>; + interrupts = <10>; + reg-shift = <2>; + reg-io-width = <4>; + }; + +Example with two clocks: + + uart@80230000 { + compatible = "snps,dw-apb-uart"; + reg = <0x80230000 0x100>; + clocks = <&baudclk>, <&apb_pclk>; + clock-names = "baudclk", "apb_pclk"; + interrupts = <10>; + reg-shift = <2>; + reg-io-width = <4>; + }; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt index a6a32cb7f777..1bae71e9ad47 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt @@ -4,6 +4,7 @@ Required properties: - compatible: Should be "fsl,imx27-usb" - reg: Should contain registers location and length - interrupts: Should contain controller interrupt +- fsl,usbphy: phandle of usb phy that connects to the port Recommended properies: - phy_type: the type of the phy connected to the core. Should be one @@ -12,7 +13,6 @@ Recommended properies: - dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg" Optional properties: -- fsl,usbphy: phandler of usb phy that connects to the only one port - fsl,usbmisc: phandler of non-core register device, with one argument that indicate usb controller index - vbus-supply: regulator for vbus diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt index ba797d3e6326..c9205fbf26e2 100644 --- a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt @@ -20,6 +20,12 @@ Required properties : Present if phy_type == utmi. - ulpi-link: The clock Tegra provides to the ULPI PHY (cdev2). Present if phy_type == ulpi, and ULPI link mode is in use. + - resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names : Must include the following entries: + - usb: The PHY's own reset signal. + - utmi-pads: The reset of the PHY containing the chip-wide UTMI pad control + registers. Required even if phy_type == ulpi. Required properties for phy_type == ulpi: - nvidia,phy-reset-gpio : The GPIO used to reset the PHY. @@ -56,6 +62,8 @@ Optional properties: host means this is a host controller peripheral means it is device controller otg means it can operate as either ("on the go") + - nvidia,has-utmi-pad-registers : boolean indicates whether this controller + contains the UTMI pad control registers common to all USB controllers. VBUS control (required for dr_mode == otg, optional for dr_mode == host): - vbus-supply: regulator for VBUS diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt index 5a79377c6a96..86f67f0886bc 100644 --- a/Documentation/devicetree/bindings/usb/usb-xhci.txt +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -9,8 +9,9 @@ Required properties: register set for the device. - interrupts: one XHCI interrupt should be described here. -Optional property: +Optional properties: - clocks: reference to a clock + - usb3-lpm-capable: determines if platform is USB3 LPM capable Example: usb@f0931000 { diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 46a311e728a8..97c9c06132c4 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -42,6 +42,7 @@ dmo Data Modul AG ebv EBV Elektronik edt Emerging Display Technologies emmicro EM Microelectronic +epcos EPCOS AG epfl Ecole Polytechnique Fédérale de Lausanne epson Seiko Epson Corp. est ESTeem Wireless Modems |