diff options
Diffstat (limited to 'Documentation/devicetree')
7 files changed, 41 insertions, 35 deletions
diff --git a/Documentation/devicetree/bindings/input/atmel,maxtouch.txt b/Documentation/devicetree/bindings/input/atmel,maxtouch.txt index 23e3abc3fdef..c88919480d37 100644 --- a/Documentation/devicetree/bindings/input/atmel,maxtouch.txt +++ b/Documentation/devicetree/bindings/input/atmel,maxtouch.txt @@ -4,6 +4,13 @@ Required properties: - compatible: atmel,maxtouch + The following compatibles have been used in various products but are + deprecated: + atmel,qt602240_ts + atmel,atmel_mxt_ts + atmel,atmel_mxt_tp + atmel,mXT224 + - reg: The I2C address of the device - interrupts: The sink for the touchpad's IRQ output diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index 0cc5417904dd..106808b55b6d 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -17,6 +17,8 @@ Required properties: - "renesas,scifa-r8a7745" for R8A7745 (RZ/G1E) SCIFA compatible UART. - "renesas,scifb-r8a7745" for R8A7745 (RZ/G1E) SCIFB compatible UART. - "renesas,hscif-r8a7745" for R8A7745 (RZ/G1E) HSCIF compatible UART. + - "renesas,scif-r8a77470" for R8A77470 (RZ/G1C) SCIF compatible UART. + - "renesas,hscif-r8a77470" for R8A77470 (RZ/G1C) HSCIF compatible UART. - "renesas,scif-r8a7778" for R8A7778 (R-Car M1) SCIF compatible UART. - "renesas,scif-r8a7779" for R8A7779 (R-Car H1) SCIF compatible UART. - "renesas,scif-r8a7790" for R8A7790 (R-Car H2) SCIF compatible UART. diff --git a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt index 1b596fd38dc4..b957acff57aa 100644 --- a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt @@ -49,19 +49,6 @@ on the SoC (only first trip points defined in DT will be configured): - samsung,exynos5433-tmu: 8 - samsung,exynos7-tmu: 8 -Following properties are mandatory (depending on SoC): -- samsung,tmu_gain: Gain value for internal TMU operation. -- samsung,tmu_reference_voltage: Value of TMU IP block's reference voltage -- samsung,tmu_noise_cancel_mode: Mode for noise cancellation -- samsung,tmu_efuse_value: Default level of temperature - it is needed when - in factory fusing produced wrong value -- samsung,tmu_min_efuse_value: Minimum temperature fused value -- samsung,tmu_max_efuse_value: Maximum temperature fused value -- samsung,tmu_first_point_trim: First point trimming value -- samsung,tmu_second_point_trim: Second point trimming value -- samsung,tmu_default_temp_offset: Default temperature offset -- samsung,tmu_cal_type: Callibration type - ** Optional properties: - vtmu-supply: This entry is optional and provides the regulator node supplying @@ -78,7 +65,7 @@ Example 1): clocks = <&clock 383>; clock-names = "tmu_apbif"; vtmu-supply = <&tmu_regulator_node>; - #include "exynos4412-tmu-sensor-conf.dtsi" + #thermal-sensor-cells = <0>; }; Example 2): @@ -89,7 +76,7 @@ Example 2): interrupts = <0 58 0>; clocks = <&clock 21>; clock-names = "tmu_apbif"; - #include "exynos5440-tmu-sensor-conf.dtsi" + #thermal-sensor-cells = <0>; }; Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register") @@ -99,7 +86,7 @@ Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register") interrupts = <0 184 0>; clocks = <&clock 318>, <&clock 318>; clock-names = "tmu_apbif", "tmu_triminfo_apbif"; - #include "exynos4412-tmu-sensor-conf.dtsi" + #thermal-sensor-cells = <0>; }; tmu_cpu3: tmu@1006c000 { @@ -108,7 +95,7 @@ Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register") interrupts = <0 185 0>; clocks = <&clock 318>, <&clock 319>; clock-names = "tmu_apbif", "tmu_triminfo_apbif"; - #include "exynos4412-tmu-sensor-conf.dtsi" + #thermal-sensor-cells = <0>; }; tmu_gpu: tmu@100a0000 { @@ -117,7 +104,7 @@ Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register") interrupts = <0 215 0>; clocks = <&clock 319>, <&clock 318>; clock-names = "tmu_apbif", "tmu_triminfo_apbif"; - #include "exynos4412-tmu-sensor-conf.dtsi" + #thermal-sensor-cells = <0>; }; Note: For multi-instance tmu each instance should have an alias correctly diff --git a/Documentation/devicetree/bindings/thermal/thermal.txt b/Documentation/devicetree/bindings/thermal/thermal.txt index 1719d47a5e2f..cc553f0952c5 100644 --- a/Documentation/devicetree/bindings/thermal/thermal.txt +++ b/Documentation/devicetree/bindings/thermal/thermal.txt @@ -55,8 +55,7 @@ of heat dissipation). For example a fan's cooling states correspond to the different fan speeds possible. Cooling states are referred to by single unsigned integers, where larger numbers mean greater heat dissipation. The precise set of cooling states associated with a device -(as referred to by the cooling-min-level and cooling-max-level -properties) should be defined in a particular device's binding. +should be defined in a particular device's binding. For more examples of cooling devices, refer to the example sections below. Required properties: @@ -69,15 +68,6 @@ Required properties: See Cooling device maps section below for more details on how consumers refer to cooling devices. -Optional properties: -- cooling-min-level: An integer indicating the smallest - Type: unsigned cooling state accepted. Typically 0. - Size: one cell - -- cooling-max-level: An integer indicating the largest - Type: unsigned cooling state accepted. - Size: one cell - * Trip points The trip node is a node to describe a point in the temperature domain @@ -226,8 +216,6 @@ cpus { 396000 950000 198000 850000 >; - cooling-min-level = <0>; - cooling-max-level = <3>; #cooling-cells = <2>; /* min followed by max */ }; ... @@ -241,8 +229,6 @@ cpus { */ fan0: fan@48 { ... - cooling-min-level = <0>; - cooling-max-level = <9>; #cooling-cells = <2>; /* min followed by max */ }; }; diff --git a/Documentation/devicetree/bindings/timer/nuvoton,npcm7xx-timer.txt b/Documentation/devicetree/bindings/timer/nuvoton,npcm7xx-timer.txt new file mode 100644 index 000000000000..ea22dfe485be --- /dev/null +++ b/Documentation/devicetree/bindings/timer/nuvoton,npcm7xx-timer.txt @@ -0,0 +1,21 @@ +Nuvoton NPCM7xx timer + +Nuvoton NPCM7xx have three timer modules, each timer module provides five 24-bit +timer counters. + +Required properties: +- compatible : "nuvoton,npcm750-timer" for Poleg NPCM750. +- reg : Offset and length of the register set for the device. +- interrupts : Contain the timer interrupt with flags for + falling edge. +- clocks : phandle of timer reference clock (usually a 25 MHz clock). + +Example: + +timer@f0008000 { + compatible = "nuvoton,npcm750-timer"; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + reg = <0xf0008000 0x50>; + clocks = <&clk NPCM7XX_CLK_TIMER>; +}; + diff --git a/Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt b/Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt index b4aa7ddb5b13..f82087b220f4 100644 --- a/Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt +++ b/Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt @@ -15,7 +15,7 @@ Required properties: - interrupts : Should be the clock event device interrupt. - clocks : The clocks provided by the SoC to drive the timer, must contain an entry for each entry in clock-names. -- clock-names : Must include the following entries: "igp" and "per". +- clock-names : Must include the following entries: "ipg" and "per". Example: tpm5: tpm@40260000 { diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt index c4c00dff4b56..bd1dd316fb23 100644 --- a/Documentation/devicetree/bindings/usb/usb-xhci.txt +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -28,7 +28,10 @@ Required properties: - interrupts: one XHCI interrupt should be described here. Optional properties: - - clocks: reference to a clock + - clocks: reference to the clocks + - clock-names: mandatory if there is a second clock, in this case + the name must be "core" for the first clock and "reg" for the + second one - usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM - usb3-lpm-capable: determines if platform is USB3 LPM capable - quirk-broken-port-ped: set if the controller has broken port disable mechanism |