diff options
Diffstat (limited to 'Documentation/devicetree')
753 files changed, 25205 insertions, 1961 deletions
diff --git a/Documentation/devicetree/00-INDEX b/Documentation/devicetree/00-INDEX index b78f691fd847..8c4102c6a5e7 100644 --- a/Documentation/devicetree/00-INDEX +++ b/Documentation/devicetree/00-INDEX @@ -8,3 +8,5 @@ https://lists.ozlabs.org/listinfo/devicetree-discuss - this file booting-without-of.txt - Booting Linux without Open Firmware, describes history and format of device trees. +usage-model.txt + - How Linux uses DT and what DT aims to solve.
\ No newline at end of file diff --git a/Documentation/devicetree/bindings/arm/adapteva.txt b/Documentation/devicetree/bindings/arm/adapteva.txt new file mode 100644 index 000000000000..1d8af9e36065 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/adapteva.txt @@ -0,0 +1,7 @@ +Adapteva Platforms Device Tree Bindings +--------------------------------------- + +Parallella board + +Required root node properties: + - compatible = "adapteva,parallella"; diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-sdram-edac.txt b/Documentation/devicetree/bindings/arm/altera/socfpga-sdram-edac.txt new file mode 100644 index 000000000000..d0ce01da5c59 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/altera/socfpga-sdram-edac.txt @@ -0,0 +1,15 @@ +Altera SOCFPGA SDRAM Error Detection & Correction [EDAC] +The EDAC accesses a range of registers in the SDRAM controller. + +Required properties: +- compatible : should contain "altr,sdram-edac"; +- altr,sdr-syscon : phandle of the sdr module +- interrupts : Should contain the SDRAM ECC IRQ in the + appropriate format for the IRQ controller. + +Example: + sdramedac { + compatible = "altr,sdram-edac"; + altr,sdr-syscon = <&sdr>; + interrupts = <0 39 4>; + }; diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt new file mode 100644 index 000000000000..8fe815046140 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/amlogic.txt @@ -0,0 +1,10 @@ +Amlogic MesonX device tree bindings +------------------------------------------- + +Boards with the Amlogic Meson6 SoC shall have the following properties: + Required root node property: + compatible: "amlogic,meson6" + +Boards with the Amlogic Meson8 SoC shall have the following properties: + Required root node property: + compatible: "amlogic,meson8"; diff --git a/Documentation/devicetree/bindings/arm/arch_timer.txt b/Documentation/devicetree/bindings/arm/arch_timer.txt index 06fc7602593a..256b4d8bab7b 100644 --- a/Documentation/devicetree/bindings/arm/arch_timer.txt +++ b/Documentation/devicetree/bindings/arm/arch_timer.txt @@ -19,6 +19,17 @@ to deliver its interrupts via SPIs. - clock-frequency : The frequency of the main counter, in Hz. Optional. +- always-on : a boolean property. If present, the timer is powered through an + always-on power domain, therefore it never loses context. + +** Optional properties: + +- arm,cpu-registers-not-fw-configured : Firmware does not initialize + any of the generic timer CPU registers, which contain their + architecturally-defined reset values. Only supported for 32-bit + systems which follow the ARMv7 architected reset values. + + Example: timer { diff --git a/Documentation/devicetree/bindings/arm/arm-boards b/Documentation/devicetree/bindings/arm/arm-boards index 3509707f9320..556c8665fdbf 100644 --- a/Documentation/devicetree/bindings/arm/arm-boards +++ b/Documentation/devicetree/bindings/arm/arm-boards @@ -86,3 +86,74 @@ Interrupt controllers: compatible = "arm,versatile-sic"; interrupt-controller; #interrupt-cells = <1>; + +Required nodes: + +- core-module: the root node to the Versatile platforms must have + a core-module with regs and the compatible strings + "arm,core-module-versatile", "syscon" + +ARM RealView Boards +------------------- +The RealView boards cover tailored evaluation boards that are used to explore +the ARM11 and Cortex A-8 and Cortex A-9 processors. + +Required properties (in root node): + /* RealView Emulation Baseboard */ + compatible = "arm,realview-eb"; + /* RealView Platform Baseboard for ARM1176JZF-S */ + compatible = "arm,realview-pb1176"; + /* RealView Platform Baseboard for ARM11 MPCore */ + compatible = "arm,realview-pb11mp"; + /* RealView Platform Baseboard for Cortex A-8 */ + compatible = "arm,realview-pba8"; + /* RealView Platform Baseboard Explore for Cortex A-9 */ + compatible = "arm,realview-pbx"; + +Required nodes: + +- soc: some node of the RealView platforms must be the SoC + node that contain the SoC-specific devices, withe the compatible + string set to one of these tuples: + "arm,realview-eb-soc", "simple-bus" + "arm,realview-pb1176-soc", "simple-bus" + "arm,realview-pb11mp-soc", "simple-bus" + "arm,realview-pba8-soc", "simple-bus" + "arm,realview-pbx-soc", "simple-bus" + +- syscon: some subnode of the RealView SoC node must be a + system controller node pointing to the control registers, + with the compatible string set to one of these tuples: + "arm,realview-eb-syscon", "syscon" + "arm,realview-pb1176-syscon", "syscon" + "arm,realview-pb11mp-syscon", "syscon" + "arm,realview-pba8-syscon", "syscon" + "arm,realview-pbx-syscon", "syscon" + + Required properties for the system controller: + - regs: the location and size of the system controller registers, + one range of 0x1000 bytes. + +Example: + +/dts-v1/; +#include <dt-bindings/interrupt-controller/irq.h> +#include "skeleton.dtsi" + +/ { + model = "ARM RealView PB1176 with device tree"; + compatible = "arm,realview-pb1176"; + + soc { + #address-cells = <1>; + #size-cells = <1>; + compatible = "arm,realview-pb1176-soc", "simple-bus"; + ranges; + + syscon: syscon@10000000 { + compatible = "arm,realview-syscon", "syscon"; + reg = <0x10000000 0x1000>; + }; + + }; +}; diff --git a/Documentation/devicetree/bindings/arm/armada-370-xp-pmsu.txt b/Documentation/devicetree/bindings/arm/armada-370-xp-pmsu.txt index 926b4d6aae7e..26799ef562df 100644 --- a/Documentation/devicetree/bindings/arm/armada-370-xp-pmsu.txt +++ b/Documentation/devicetree/bindings/arm/armada-370-xp-pmsu.txt @@ -1,20 +1,21 @@ Power Management Service Unit(PMSU) ----------------------------------- -Available on Marvell SOCs: Armada 370 and Armada XP +Available on Marvell SOCs: Armada 370, Armada 38x and Armada XP Required properties: -- compatible: "marvell,armada-370-xp-pmsu" +- compatible: should be one of: + - "marvell,armada-370-pmsu" for Armada 370 or Armada XP + - "marvell,armada-380-pmsu" for Armada 38x + - "marvell,armada-370-xp-pmsu" was used for Armada 370/XP but is now + deprecated and will be removed -- reg: Should contain PMSU registers location and length. First pair - for the per-CPU SW Reset Control registers, second pair for the - Power Management Service Unit. +- reg: Should contain PMSU registers location and length. Example: -armada-370-xp-pmsu@d0022000 { - compatible = "marvell,armada-370-xp-pmsu"; - reg = <0xd0022100 0x430>, - <0xd0020800 0x20>; +armada-370-xp-pmsu@22000 { + compatible = "marvell,armada-370-pmsu"; + reg = <0x22000 0x1000>; }; diff --git a/Documentation/devicetree/bindings/arm/armada-375.txt b/Documentation/devicetree/bindings/arm/armada-375.txt new file mode 100644 index 000000000000..867d0b80cb8f --- /dev/null +++ b/Documentation/devicetree/bindings/arm/armada-375.txt @@ -0,0 +1,9 @@ +Marvell Armada 375 Platforms Device Tree Bindings +------------------------------------------------- + +Boards with a SoC of the Marvell Armada 375 family shall have the +following property: + +Required root node property: + +compatible: must contain "marvell,armada375" diff --git a/Documentation/devicetree/bindings/arm/armada-380-mpcore-soc-ctrl.txt b/Documentation/devicetree/bindings/arm/armada-380-mpcore-soc-ctrl.txt new file mode 100644 index 000000000000..8781073029e9 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/armada-380-mpcore-soc-ctrl.txt @@ -0,0 +1,14 @@ +Marvell Armada 38x CA9 MPcore SoC Controller +============================================ + +Required properties: + +- compatible: Should be "marvell,armada-380-mpcore-soc-ctrl". + +- reg: should be the register base and length as documented in the + datasheet for the CA9 MPcore SoC Control registers + +mpcore-soc-ctrl@20d20 { + compatible = "marvell,armada-380-mpcore-soc-ctrl"; + reg = <0x20d20 0x6c>; +}; diff --git a/Documentation/devicetree/bindings/arm/armada-38x.txt b/Documentation/devicetree/bindings/arm/armada-38x.txt new file mode 100644 index 000000000000..ad9f8ed4d9bd --- /dev/null +++ b/Documentation/devicetree/bindings/arm/armada-38x.txt @@ -0,0 +1,20 @@ +Marvell Armada 38x Platforms Device Tree Bindings +------------------------------------------------- + +Boards with a SoC of the Marvell Armada 38x family shall have the +following property: + +Required root node property: + + - compatible: must contain "marvell,armada380" + +In addition, boards using the Marvell Armada 385 SoC shall have the +following property before the previous one: + +Required root node property: + +compatible: must contain "marvell,armada385" + +Example: + +compatible = "marvell,a385-rd", "marvell,armada385", "marvell,armada380"; diff --git a/Documentation/devicetree/bindings/arm/armada-cpu-reset.txt b/Documentation/devicetree/bindings/arm/armada-cpu-reset.txt new file mode 100644 index 000000000000..b63a7b6ab998 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/armada-cpu-reset.txt @@ -0,0 +1,14 @@ +Marvell Armada CPU reset controller +=================================== + +Required properties: + +- compatible: Should be "marvell,armada-370-cpu-reset". + +- reg: should be register base and length as documented in the + datasheet for the CPU reset registers + +cpurst: cpurst@20800 { + compatible = "marvell,armada-370-cpu-reset"; + reg = <0x20800 0x20>; +}; diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt index 16f60b41c147..562cda9d86d9 100644 --- a/Documentation/devicetree/bindings/arm/atmel-at91.txt +++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt @@ -1,6 +1,43 @@ Atmel AT91 device tree bindings. ================================ +Boards with a SoC of the Atmel AT91 or SMART family shall have the following +properties: + +Required root node properties: +compatible: must be one of: + * "atmel,at91rm9200" + + * "atmel,at91sam9" for SoCs using an ARM926EJ-S core, shall be extended with + the specific SoC family or compatible: + o "atmel,at91sam9260" + o "atmel,at91sam9261" + o "atmel,at91sam9263" + o "atmel,at91sam9x5" for the 5 series, shall be extended with the specific + SoC compatible: + - "atmel,at91sam9g15" + - "atmel,at91sam9g25" + - "atmel,at91sam9g35" + - "atmel,at91sam9x25" + - "atmel,at91sam9x35" + o "atmel,at91sam9g20" + o "atmel,at91sam9g45" + o "atmel,at91sam9n12" + o "atmel,at91sam9rl" + * "atmel,sama5" for SoCs using a Cortex-A5, shall be extended with the specific + SoC family: + o "atmel,sama5d3" shall be extended with the specific SoC compatible: + - "atmel,sama5d31" + - "atmel,sama5d33" + - "atmel,sama5d34" + - "atmel,sama5d35" + - "atmel,sama5d36" + o "atmel,sama5d4" shall be extended with the specific SoC compatible: + - "atmel,sama5d41" + - "atmel,sama5d42" + - "atmel,sama5d43" + - "atmel,sama5d44" + PIT Timer required properties: - compatible: Should be "atmel,at91sam9260-pit" - reg: Should contain registers location and length @@ -61,8 +98,8 @@ RAMC SDRAM/DDR Controller required properties: - compatible: Should be "atmel,at91rm9200-sdramc", "atmel,at91sam9260-sdramc", "atmel,at91sam9g45-ddramc", + "atmel,sama5d3-ddramc", - reg: Should contain registers location and length - For at91sam9263 and at91sam9g45 you must specify 2 entries. Examples: @@ -71,12 +108,6 @@ Examples: reg = <0xffffe800 0x200>; }; - ramc0: ramc@ffffe400 { - compatible = "atmel,at91sam9g45-ddramc"; - reg = <0xffffe400 0x200 - 0xffffe600 0x200>; - }; - SHDWC Shutdown Controller required properties: diff --git a/Documentation/devicetree/bindings/arm/atmel-pmc.txt b/Documentation/devicetree/bindings/arm/atmel-pmc.txt index 389bed5056e8..795cc78543fe 100644 --- a/Documentation/devicetree/bindings/arm/atmel-pmc.txt +++ b/Documentation/devicetree/bindings/arm/atmel-pmc.txt @@ -1,7 +1,10 @@ * Power Management Controller (PMC) Required properties: -- compatible: Should be "atmel,at91rm9200-pmc" +- compatible: Should be "atmel,<chip>-pmc". + <chip> can be: at91rm9200, at91sam9260, at91sam9g45, at91sam9n12, + at91sam9x5, sama5d3 + - reg: Should contain PMC registers location and length Examples: diff --git a/Documentation/devicetree/bindings/arm/axxia.txt b/Documentation/devicetree/bindings/arm/axxia.txt new file mode 100644 index 000000000000..7b4ef9c07696 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/axxia.txt @@ -0,0 +1,12 @@ +Axxia AXM55xx device tree bindings + +Boards using the AXM55xx SoC need to have the following properties: + +Required root node property: + + - compatible = "lsi,axm5516" + +Boards: + + LSI AXM5516 Validation board (Amarillo) + compatible = "lsi,axm5516-amarillo", "lsi,axm5516" diff --git a/Documentation/devicetree/bindings/arm/bcm/bcm21664.txt b/Documentation/devicetree/bindings/arm/bcm/bcm21664.txt new file mode 100644 index 000000000000..e0774255e1a6 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/bcm21664.txt @@ -0,0 +1,15 @@ +Broadcom BCM21664 device tree bindings +-------------------------------------- + +This document describes the device tree bindings for boards with the BCM21664 +SoC. + +Required root node property: + - compatible: brcm,bcm21664 + +Example: + / { + model = "BCM21664 SoC"; + compatible = "brcm,bcm21664"; + [...] + } diff --git a/Documentation/devicetree/bindings/arm/bcm/bcm63138.txt b/Documentation/devicetree/bindings/arm/bcm/bcm63138.txt new file mode 100644 index 000000000000..bd49987a8812 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/bcm63138.txt @@ -0,0 +1,9 @@ +Broadcom BCM63138 DSL System-on-a-Chip device tree bindings +----------------------------------------------------------- + +Boards compatible with the BCM63138 DSL System-on-a-Chip should have the +following properties: + +Required root node property: + +compatible: should be "brcm,bcm63138" diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm11351-cpu-method b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm11351-cpu-method new file mode 100644 index 000000000000..8240c023e202 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm11351-cpu-method @@ -0,0 +1,36 @@ +Broadcom Kona Family CPU Enable Method +-------------------------------------- +This binding defines the enable method used for starting secondary +CPUs in the following Broadcom SoCs: + BCM11130, BCM11140, BCM11351, BCM28145, BCM28155, BCM21664 + +The enable method is specified by defining the following required +properties in the "cpus" device tree node: + - enable-method = "brcm,bcm11351-cpu-method"; + - secondary-boot-reg = <...>; + +The secondary-boot-reg property is a u32 value that specifies the +physical address of the register used to request the ROM holding pen +code release a secondary CPU. The value written to the register is +formed by encoding the target CPU id into the low bits of the +physical start address it should jump to. + +Example: + cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "brcm,bcm11351-cpu-method"; + secondary-boot-reg = <0x3500417c>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + reg = <0>; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/bcm/cygnus.txt b/Documentation/devicetree/bindings/arm/bcm/cygnus.txt new file mode 100644 index 000000000000..4c77169bb534 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/cygnus.txt @@ -0,0 +1,31 @@ +Broadcom Cygnus device tree bindings +------------------------------------ + + +Boards with Cygnus SoCs shall have the following properties: + +Required root node property: + +BCM11300 +compatible = "brcm,bcm11300", "brcm,cygnus"; + +BCM11320 +compatible = "brcm,bcm11320", "brcm,cygnus"; + +BCM11350 +compatible = "brcm,bcm11350", "brcm,cygnus"; + +BCM11360 +compatible = "brcm,bcm11360", "brcm,cygnus"; + +BCM58300 +compatible = "brcm,bcm58300", "brcm,cygnus"; + +BCM58302 +compatible = "brcm,bcm58302", "brcm,cygnus"; + +BCM58303 +compatible = "brcm,bcm58303", "brcm,cygnus"; + +BCM58305 +compatible = "brcm,bcm58305", "brcm,cygnus"; diff --git a/Documentation/devicetree/bindings/arm/bcm/kona-resetmgr.txt b/Documentation/devicetree/bindings/arm/bcm/kona-resetmgr.txt new file mode 100644 index 000000000000..93f31ca1ef4b --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/kona-resetmgr.txt @@ -0,0 +1,14 @@ +Broadcom Kona Family Reset Manager +---------------------------------- + +The reset manager is used on the Broadcom BCM21664 SoC. + +Required properties: + - compatible: brcm,bcm21664-resetmgr + - reg: memory address & range + +Example: + brcm,resetmgr@35001f00 { + compatible = "brcm,bcm21664-resetmgr"; + reg = <0x35001f00 0x24>; + }; diff --git a/Documentation/devicetree/bindings/arm/bcm4708.txt b/Documentation/devicetree/bindings/arm/bcm4708.txt new file mode 100644 index 000000000000..6b0f49f6f499 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm4708.txt @@ -0,0 +1,8 @@ +Broadcom BCM4708 device tree bindings +------------------------------------------- + +Boards with the BCM4708 SoC shall have the following properties: + +Required root node property: + +compatible = "brcm,bcm4708"; diff --git a/Documentation/devicetree/bindings/arm/brcm-brcmstb.txt b/Documentation/devicetree/bindings/arm/brcm-brcmstb.txt new file mode 100644 index 000000000000..3c436cc4f35d --- /dev/null +++ b/Documentation/devicetree/bindings/arm/brcm-brcmstb.txt @@ -0,0 +1,95 @@ +ARM Broadcom STB platforms Device Tree Bindings +----------------------------------------------- +Boards with Broadcom Brahma15 ARM-based BCMxxxx (generally BCM7xxx variants) +SoC shall have the following DT organization: + +Required root node properties: + - compatible: "brcm,bcm<chip_id>", "brcm,brcmstb" + +example: +/ { + #address-cells = <2>; + #size-cells = <2>; + model = "Broadcom STB (bcm7445)"; + compatible = "brcm,bcm7445", "brcm,brcmstb"; + +Further, syscon nodes that map platform-specific registers used for general +system control is required: + + - compatible: "brcm,bcm<chip_id>-sun-top-ctrl", "syscon" + - compatible: "brcm,bcm<chip_id>-hif-cpubiuctrl", "syscon" + - compatible: "brcm,bcm<chip_id>-hif-continuation", "syscon" + +example: + rdb { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + ranges = <0 0x00 0xf0000000 0x1000000>; + + sun_top_ctrl: syscon@404000 { + compatible = "brcm,bcm7445-sun-top-ctrl", "syscon"; + reg = <0x404000 0x51c>; + }; + + hif_cpubiuctrl: syscon@3e2400 { + compatible = "brcm,bcm7445-hif-cpubiuctrl", "syscon"; + reg = <0x3e2400 0x5b4>; + }; + + hif_continuation: syscon@452000 { + compatible = "brcm,bcm7445-hif-continuation", "syscon"; + reg = <0x452000 0x100>; + }; + }; + +Lastly, nodes that allow for support of SMP initialization and reboot are +required: + +smpboot +------- +Required properties: + + - compatible + The string "brcm,brcmstb-smpboot". + + - syscon-cpu + A phandle / integer array property which lets the BSP know the location + of certain CPU power-on registers. + + The layout of the property is as follows: + o a phandle to the "hif_cpubiuctrl" syscon node + o offset to the base CPU power zone register + o offset to the base CPU reset register + + - syscon-cont + A phandle pointing to the syscon node which describes the CPU boot + continuation registers. + o a phandle to the "hif_continuation" syscon node + +example: + smpboot { + compatible = "brcm,brcmstb-smpboot"; + syscon-cpu = <&hif_cpubiuctrl 0x88 0x178>; + syscon-cont = <&hif_continuation>; + }; + +reboot +------- +Required properties + + - compatible + The string property "brcm,brcmstb-reboot". + + - syscon + A phandle / integer array that points to the syscon node which describes + the general system reset registers. + o a phandle to "sun_top_ctrl" + o offset to the "reset source enable" register + o offset to the "software master reset" register + +example: + reboot { + compatible = "brcm,brcmstb-reboot"; + syscon = <&sun_top_ctrl 0x304 0x308>; + }; diff --git a/Documentation/devicetree/bindings/arm/cavium-thunder.txt b/Documentation/devicetree/bindings/arm/cavium-thunder.txt new file mode 100644 index 000000000000..6f63a5866902 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/cavium-thunder.txt @@ -0,0 +1,10 @@ +Cavium Thunder platform device tree bindings +-------------------------------------------- + +Boards with Cavium's Thunder SoC shall have following properties. + +Root Node +--------- +Required root node properties: + + - compatible = "cavium,thunder-88xx"; diff --git a/Documentation/devicetree/bindings/arm/ccn.txt b/Documentation/devicetree/bindings/arm/ccn.txt new file mode 100644 index 000000000000..b100d3847d88 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/ccn.txt @@ -0,0 +1,21 @@ +* ARM CCN (Cache Coherent Network) + +Required properties: + +- compatible: (standard compatible string) should be one of: + "arm,ccn-504" + "arm,ccn-508" + +- reg: (standard registers property) physical address and size + (16MB) of the configuration registers block + +- interrupts: (standard interrupt property) single interrupt + generated by the control block + +Example: + + ccn@0x2000000000 { + compatible = "arm,ccn-504"; + reg = <0x20 0x00000000 0 0x1000000>; + interrupts = <0 181 4>; + }; diff --git a/Documentation/devicetree/bindings/arm/coherency-fabric.txt b/Documentation/devicetree/bindings/arm/coherency-fabric.txt index 17d8cd107559..8dd46617c889 100644 --- a/Documentation/devicetree/bindings/arm/coherency-fabric.txt +++ b/Documentation/devicetree/bindings/arm/coherency-fabric.txt @@ -1,16 +1,33 @@ Coherency fabric ---------------- -Available on Marvell SOCs: Armada 370 and Armada XP +Available on Marvell SOCs: Armada 370, Armada 375, Armada 38x and Armada XP Required properties: -- compatible: "marvell,coherency-fabric" +- compatible: the possible values are: + + * "marvell,coherency-fabric", to be used for the coherency fabric of + the Armada 370 and Armada XP. + + * "marvell,armada-375-coherency-fabric", for the Armada 375 coherency + fabric. + + * "marvell,armada-380-coherency-fabric", for the Armada 38x coherency + fabric. - reg: Should contain coherency fabric registers location and - length. First pair for the coherency fabric registers, second pair - for the per-CPU fabric registers registers. + length. + + * For "marvell,coherency-fabric", the first pair for the coherency + fabric registers, second pair for the per-CPU fabric registers. -Example: + * For "marvell,armada-375-coherency-fabric", only one pair is needed + for the per-CPU fabric registers. + + * For "marvell,armada-380-coherency-fabric", only one pair is needed + for the per-CPU fabric registers. + +Examples: coherency-fabric@d0020200 { compatible = "marvell,coherency-fabric"; @@ -19,3 +36,8 @@ coherency-fabric@d0020200 { }; +coherency-fabric@21810 { + compatible = "marvell,armada-375-coherency-fabric"; + reg = <0x21810 0x1c>; +}; + diff --git a/Documentation/devicetree/bindings/arm/cpu-enable-method/marvell,berlin-smp b/Documentation/devicetree/bindings/arm/cpu-enable-method/marvell,berlin-smp new file mode 100644 index 000000000000..cd236b727e2a --- /dev/null +++ b/Documentation/devicetree/bindings/arm/cpu-enable-method/marvell,berlin-smp @@ -0,0 +1,41 @@ +======================================================== +Secondary CPU enable-method "marvell,berlin-smp" binding +======================================================== + +This document describes the "marvell,berlin-smp" method for enabling secondary +CPUs. To apply to all CPUs, a single "marvell,berlin-smp" enable method should +be defined in the "cpus" node. + +Enable method name: "marvell,berlin-smp" +Compatible machines: "marvell,berlin2" and "marvell,berlin2q" +Compatible CPUs: "marvell,pj4b" and "arm,cortex-a9" +Related properties: (none) + +Note: +This enable method needs valid nodes compatible with "arm,cortex-a9-scu" and +"marvell,berlin-cpu-ctrl"[1]. + +Example: + + cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "marvell,berlin-smp"; + + cpu@0 { + compatible = "marvell,pj4b"; + device_type = "cpu"; + next-level-cache = <&l2>; + reg = <0>; + }; + + cpu@1 { + compatible = "marvell,pj4b"; + device_type = "cpu"; + next-level-cache = <&l2>; + reg = <1>; + }; + }; + +-- +[1] arm/marvell,berlin.txt diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index 91304353eea4..b2aacbe16ed9 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -152,7 +152,9 @@ nodes to be present and contain the properties described below. "arm,cortex-a7" "arm,cortex-a8" "arm,cortex-a9" + "arm,cortex-a12" "arm,cortex-a15" + "arm,cortex-a17" "arm,cortex-a53" "arm,cortex-a57" "arm,cortex-m0" @@ -163,6 +165,8 @@ nodes to be present and contain the properties described below. "arm,cortex-r4" "arm,cortex-r5" "arm,cortex-r7" + "brcm,brahma-b15" + "cavium,thunder" "faraday,fa526" "intel,sa110" "intel,sa1100" @@ -178,9 +182,20 @@ nodes to be present and contain the properties described below. Usage and definition depend on ARM architecture version. # On ARM v8 64-bit this property is required and must be one of: - "spin-table" "psci" - # On ARM 32-bit systems this property is optional. + "spin-table" + # On ARM 32-bit systems this property is optional and + can be one of: + "allwinner,sun6i-a31" + "arm,psci" + "brcm,brahma-b15" + "marvell,armada-375-smp" + "marvell,armada-380-smp" + "marvell,armada-xp-smp" + "qcom,gcc-msm8660" + "qcom,kpss-acc-v1" + "qcom,kpss-acc-v2" + "rockchip,rk3066-smp" - cpu-release-addr Usage: required for systems that have an "enable-method" @@ -191,6 +206,36 @@ nodes to be present and contain the properties described below. property identifying a 64-bit zero-initialised memory location. + - qcom,saw + Usage: required for systems that have an "enable-method" + property value of "qcom,kpss-acc-v1" or + "qcom,kpss-acc-v2" + Value type: <phandle> + Definition: Specifies the SAW[1] node associated with this CPU. + + - qcom,acc + Usage: required for systems that have an "enable-method" + property value of "qcom,kpss-acc-v1" or + "qcom,kpss-acc-v2" + Value type: <phandle> + Definition: Specifies the ACC[2] node associated with this CPU. + + - cpu-idle-states + Usage: Optional + Value type: <prop-encoded-array> + Definition: + # List of phandles to idle state nodes supported + by this cpu [3]. + + - rockchip,pmu + Usage: optional for systems that have an "enable-method" + property value of "rockchip,rk3066-smp" + While optional, it is the preferred way to get access to + the cpu-core power-domains. + Value type: <phandle> + Definition: Specifies the syscon node controlling the cpu core + power domains. + Example 1 (dual-cluster big.LITTLE system 32-bit): cpus { @@ -382,3 +427,9 @@ cpus { cpu-release-addr = <0 0x20000000>; }; }; + +-- +[1] arm/msm/qcom,saw2.txt +[2] arm/msm/qcom,kpss-acc.txt +[3] ARM Linux kernel documentation - idle states bindings + Documentation/devicetree/bindings/arm/idle-states.txt diff --git a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt index 5216b419016a..abde1ea8a119 100644 --- a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt +++ b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt @@ -8,6 +8,20 @@ Required Properties: * samsung,exynos4210-pd - for exynos4210 type power domain. - reg: physical base address of the controller and length of memory mapped region. +- #power-domain-cells: number of cells in power domain specifier; + must be 0. + +Optional Properties: +- clocks: List of clock handles. The parent clocks of the input clocks to the + devices in this power domain are set to oscclk before power gating + and restored back after powering on a domain. This is required for + all domains which are powered on and off and not required for unused + domains. +- clock-names: The following clocks can be specified: + - oscclk: Oscillator clock. + - pclkN, clkN: Pairs of parent of input clock and input clock to the + devices in this power domain. Maximum of 4 pairs (N = 0 to 3) + are supported currently. Node of a device using power domains must have a samsung,power-domain property defined with a phandle to respective power domain. @@ -17,12 +31,17 @@ Example: lcd0: power-domain-lcd0 { compatible = "samsung,exynos4210-pd"; reg = <0x10023C00 0x10>; + #power-domain-cells = <0>; }; -Example of the node using power domain: - - node { - /* ... */ - samsung,power-domain = <&lcd0>; - /* ... */ + mfc_pd: power-domain@10044060 { + compatible = "samsung,exynos4210-pd"; + reg = <0x10044060 0x20>; + clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MOUT_SW_ACLK333>, + <&clock CLK_MOUT_USER_ACLK333>; + clock-names = "oscclk", "pclk0", "clk0"; + #power-domain-cells = <0>; }; + +See Documentation/devicetree/bindings/power/power_domain.txt for description +of consumer-side bindings. diff --git a/Documentation/devicetree/bindings/arm/exynos/smp-sysram.txt b/Documentation/devicetree/bindings/arm/exynos/smp-sysram.txt new file mode 100644 index 000000000000..4a0a4f70a0ce --- /dev/null +++ b/Documentation/devicetree/bindings/arm/exynos/smp-sysram.txt @@ -0,0 +1,38 @@ +Samsung Exynos SYSRAM for SMP bringup: +------------------------------------ + +Samsung SMP-capable Exynos SoCs use part of the SYSRAM for the bringup +of the secondary cores. Once the core gets powered up it executes the +code that is residing at some specific location of the SYSRAM. + +Therefore reserved section sub-nodes have to be added to the mmio-sram +declaration. These nodes are of two types depending upon secure or +non-secure execution environment. + +Required sub-node properties: +- compatible : depending upon boot mode, should be + "samsung,exynos4210-sysram" : for Secure SYSRAM + "samsung,exynos4210-sysram-ns" : for Non-secure SYSRAM + +The rest of the properties should follow the generic mmio-sram discription +found in ../../misc/sysram.txt + +Example: + + sysram@02020000 { + compatible = "mmio-sram"; + reg = <0x02020000 0x54000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x02020000 0x54000>; + + smp-sysram@0 { + compatible = "samsung,exynos4210-sysram"; + reg = <0x0 0x1000>; + }; + + smp-sysram@53000 { + compatible = "samsung,exynos4210-sysram-ns"; + reg = <0x53000 0x1000>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt index e935d7d4ac43..4e8b7df7fc62 100644 --- a/Documentation/devicetree/bindings/arm/fsl.txt +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -74,3 +74,41 @@ Required root node properties: i.MX6q generic board Required root node properties: - compatible = "fsl,imx6q"; + + +Freescale LS1021A Platform Device Tree Bindings +------------------------------------------------ + +Required root node compatible properties: + - compatible = "fsl,ls1021a"; + +Freescale LS1021A SoC-specific Device Tree Bindings +------------------------------------------- + +Freescale SCFG + SCFG is the supplemental configuration unit, that provides SoC specific +configuration and status registers for the chip. Such as getting PEX port +status. + Required properties: + - compatible: should be "fsl,ls1021a-scfg" + - reg: should contain base address and length of SCFG memory-mapped registers + +Example: + scfg: scfg@1570000 { + compatible = "fsl,ls1021a-scfg"; + reg = <0x0 0x1570000 0x0 0x10000>; + }; + +Freescale DCFG + DCFG is the device configuration unit, that provides general purpose +configuration and status for the device. Such as setting the secondary +core start address and release the secondary core from holdoff and startup. + Required properties: + - compatible: should be "fsl,ls1021a-dcfg" + - reg : should contain base address and length of DCFG memory-mapped registers + +Example: + dcfg: dcfg@1ee0000 { + compatible = "fsl,ls1021a-dcfg"; + reg = <0x0 0x1ee0000 0x0 0x10000>; + }; diff --git a/Documentation/devicetree/bindings/arm/geniatech.txt b/Documentation/devicetree/bindings/arm/geniatech.txt new file mode 100644 index 000000000000..74ccba40b73b --- /dev/null +++ b/Documentation/devicetree/bindings/arm/geniatech.txt @@ -0,0 +1,5 @@ +Geniatech platforms device tree bindings +------------------------------------------- + +Geniatech ATV1200 + - compatible = "geniatech,atv1200" diff --git a/Documentation/devicetree/bindings/arm/gic-v3.txt b/Documentation/devicetree/bindings/arm/gic-v3.txt new file mode 100644 index 000000000000..33cd05e6c125 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/gic-v3.txt @@ -0,0 +1,79 @@ +* ARM Generic Interrupt Controller, version 3 + +AArch64 SMP cores are often associated with a GICv3, providing Private +Peripheral Interrupts (PPI), Shared Peripheral Interrupts (SPI), +Software Generated Interrupts (SGI), and Locality-specific Peripheral +Interrupts (LPI). + +Main node required properties: + +- compatible : should at least contain "arm,gic-v3". +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. Must be a single cell with a value of at least 3. + + The 1st cell is the interrupt type; 0 for SPI interrupts, 1 for PPI + interrupts. Other values are reserved for future use. + + The 2nd cell contains the interrupt number for the interrupt type. + SPI interrupts are in the range [0-987]. PPI interrupts are in the + range [0-15]. + + The 3rd cell is the flags, encoded as follows: + bits[3:0] trigger type and level flags. + 1 = edge triggered + 4 = level triggered + + Cells 4 and beyond are reserved for future use. When the 1st cell + has a value of 0 or 1, cells 4 and beyond act as padding, and may be + ignored. It is recommended that padding cells have a value of 0. + +- reg : Specifies base physical address(s) and size of the GIC + registers, in the following order: + - GIC Distributor interface (GICD) + - GIC Redistributors (GICR), one range per redistributor region + - GIC CPU interface (GICC) + - GIC Hypervisor interface (GICH) + - GIC Virtual CPU interface (GICV) + + GICC, GICH and GICV are optional. + +- interrupts : Interrupt source of the VGIC maintenance interrupt. + +Optional + +- redistributor-stride : If using padding pages, specifies the stride + of consecutive redistributors. Must be a multiple of 64kB. + +- #redistributor-regions: The number of independent contiguous regions + occupied by the redistributors. Required if more than one such + region is present. + +Examples: + + gic: interrupt-controller@2cf00000 { + compatible = "arm,gic-v3"; + #interrupt-cells = <3>; + interrupt-controller; + reg = <0x0 0x2f000000 0 0x10000>, // GICD + <0x0 0x2f100000 0 0x200000>, // GICR + <0x0 0x2c000000 0 0x2000>, // GICC + <0x0 0x2c010000 0 0x2000>, // GICH + <0x0 0x2c020000 0 0x2000>; // GICV + interrupts = <1 9 4>; + }; + + gic: interrupt-controller@2c010000 { + compatible = "arm,gic-v3"; + #interrupt-cells = <3>; + interrupt-controller; + redistributor-stride = <0x0 0x40000>; // 256kB stride + #redistributor-regions = <2>; + reg = <0x0 0x2c010000 0 0x10000>, // GICD + <0x0 0x2d000000 0 0x800000>, // GICR 1: CPUs 0-31 + <0x0 0x2e000000 0 0x800000>; // GICR 2: CPUs 32-63 + <0x0 0x2c040000 0 0x2000>, // GICC + <0x0 0x2c060000 0 0x2000>, // GICH + <0x0 0x2c080000 0 0x2000>; // GICV + interrupts = <1 9 4>; + }; diff --git a/Documentation/devicetree/bindings/arm/gic.txt b/Documentation/devicetree/bindings/arm/gic.txt index bae0d87a38b2..b38608af66db 100644 --- a/Documentation/devicetree/bindings/arm/gic.txt +++ b/Documentation/devicetree/bindings/arm/gic.txt @@ -16,6 +16,8 @@ Main node required properties: "arm,cortex-a9-gic" "arm,cortex-a7-gic" "arm,arm11mp-gic" + "brcm,brahma-b15-gic" + "arm,arm1176jzf-devchip-gic" - interrupt-controller : Identifies the node as an interrupt controller - #interrupt-cells : Specifies the number of cells needed to encode an interrupt source. The type shall be a <u32> and the value shall be 3. @@ -50,6 +52,11 @@ Optional regions, used when the GIC doesn't have banked registers. The offset is cpu-offset * cpu-nr. +- arm,routable-irqs : Total number of gic irq inputs which are not directly + connected from the peripherals, but are routed dynamically + by a crossbar/multiplexer preceding the GIC. The GIC irq + input line is assigned dynamically when the corresponding + peripheral's crossbar line is mapped. Example: intc: interrupt-controller@fff11000 { @@ -57,6 +64,7 @@ Example: #interrupt-cells = <3>; #address-cells = <1>; interrupt-controller; + arm,routable-irqs = <160>; reg = <0xfff11000 0x1000>, <0xfff10100 0x100>; }; diff --git a/Documentation/devicetree/bindings/arm/global_timer.txt b/Documentation/devicetree/bindings/arm/global_timer.txt index 1e548981eda4..bdae3a818793 100644 --- a/Documentation/devicetree/bindings/arm/global_timer.txt +++ b/Documentation/devicetree/bindings/arm/global_timer.txt @@ -4,8 +4,11 @@ ** Timer node required properties: -- compatible : Should be "arm,cortex-a9-global-timer" - Driver supports versions r2p0 and above. +- compatible : should contain + * "arm,cortex-a5-global-timer" for Cortex-A5 global timers. + * "arm,cortex-a9-global-timer" for Cortex-A9 global + timers or any compatible implementation. Note: driver + supports versions r2p0 and above. - interrupts : One interrupt to each core diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt index 8c7a4653508d..f717c7b48603 100644 --- a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt +++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt @@ -5,6 +5,11 @@ Hi4511 Board Required root node properties: - compatible = "hisilicon,hi3620-hi4511"; +HiP04 D01 Board +Required root node properties: + - compatible = "hisilicon,hip04-d01"; + + Hisilicon system controller Required properties: @@ -30,3 +35,46 @@ Example: resume-offset = <0x308>; reboot-offset = <0x4>; }; + +----------------------------------------------------------------------- +Hisilicon CPU controller + +Required properties: +- compatible : "hisilicon,cpuctrl" +- reg : Register address and size + +The clock registers and power registers of secondary cores are defined +in CPU controller, especially in HIX5HD2 SoC. + +----------------------------------------------------------------------- +PCTRL: Peripheral misc control register + +Required Properties: +- compatible: "hisilicon,pctrl" +- reg: Address and size of pctrl. + +Example: + + /* for Hi3620 */ + pctrl: pctrl@fca09000 { + compatible = "hisilicon,pctrl"; + reg = <0xfca09000 0x1000>; + }; + +----------------------------------------------------------------------- +Fabric: + +Required Properties: +- compatible: "hisilicon,hip04-fabric"; +- reg: Address and size of Fabric + +----------------------------------------------------------------------- +Bootwrapper boot method (software protocol on SMP): + +Required Properties: +- compatible: "hisilicon,hip04-bootwrapper"; +- boot-method: Address and size of boot method. + [0]: bootwrapper physical address + [1]: bootwrapper size + [2]: relocation physical address + [3]: relocation size diff --git a/Documentation/devicetree/bindings/arm/idle-states.txt b/Documentation/devicetree/bindings/arm/idle-states.txt new file mode 100644 index 000000000000..37375c7f3ccc --- /dev/null +++ b/Documentation/devicetree/bindings/arm/idle-states.txt @@ -0,0 +1,679 @@ +========================================== +ARM idle states binding description +========================================== + +========================================== +1 - Introduction +========================================== + +ARM systems contain HW capable of managing power consumption dynamically, +where cores can be put in different low-power states (ranging from simple +wfi to power gating) according to OS PM policies. The CPU states representing +the range of dynamic idle states that a processor can enter at run-time, can be +specified through device tree bindings representing the parameters required +to enter/exit specific idle states on a given processor. + +According to the Server Base System Architecture document (SBSA, [3]), the +power states an ARM CPU can be put into are identified by the following list: + +- Running +- Idle_standby +- Idle_retention +- Sleep +- Off + +The power states described in the SBSA document define the basic CPU states on +top of which ARM platforms implement power management schemes that allow an OS +PM implementation to put the processor in different idle states (which include +states listed above; "off" state is not an idle state since it does not have +wake-up capabilities, hence it is not considered in this document). + +Idle state parameters (eg entry latency) are platform specific and need to be +characterized with bindings that provide the required information to OS PM +code so that it can build the required tables and use them at runtime. + +The device tree binding definition for ARM idle states is the subject of this +document. + +=========================================== +2 - idle-states definitions +=========================================== + +Idle states are characterized for a specific system through a set of +timing and energy related properties, that underline the HW behaviour +triggered upon idle states entry and exit. + +The following diagram depicts the CPU execution phases and related timing +properties required to enter and exit an idle state: + +..__[EXEC]__|__[PREP]__|__[ENTRY]__|__[IDLE]__|__[EXIT]__|__[EXEC]__.. + | | | | | + + |<------ entry ------->| + | latency | + |<- exit ->| + | latency | + |<-------- min-residency -------->| + |<------- wakeup-latency ------->| + + Diagram 1: CPU idle state execution phases + +EXEC: Normal CPU execution. + +PREP: Preparation phase before committing the hardware to idle mode + like cache flushing. This is abortable on pending wake-up + event conditions. The abort latency is assumed to be negligible + (i.e. less than the ENTRY + EXIT duration). If aborted, CPU + goes back to EXEC. This phase is optional. If not abortable, + this should be included in the ENTRY phase instead. + +ENTRY: The hardware is committed to idle mode. This period must run + to completion up to IDLE before anything else can happen. + +IDLE: This is the actual energy-saving idle period. This may last + between 0 and infinite time, until a wake-up event occurs. + +EXIT: Period during which the CPU is brought back to operational + mode (EXEC). + +entry-latency: Worst case latency required to enter the idle state. The +exit-latency may be guaranteed only after entry-latency has passed. + +min-residency: Minimum period, including preparation and entry, for a given +idle state to be worthwhile energywise. + +wakeup-latency: Maximum delay between the signaling of a wake-up event and the +CPU being able to execute normal code again. If not specified, this is assumed +to be entry-latency + exit-latency. + +These timing parameters can be used by an OS in different circumstances. + +An idle CPU requires the expected min-residency time to select the most +appropriate idle state based on the expected expiry time of the next IRQ +(ie wake-up) that causes the CPU to return to the EXEC phase. + +An operating system scheduler may need to compute the shortest wake-up delay +for CPUs in the system by detecting how long will it take to get a CPU out +of an idle state, eg: + +wakeup-delay = exit-latency + max(entry-latency - (now - entry-timestamp), 0) + +In other words, the scheduler can make its scheduling decision by selecting +(eg waking-up) the CPU with the shortest wake-up latency. +The wake-up latency must take into account the entry latency if that period +has not expired. The abortable nature of the PREP period can be ignored +if it cannot be relied upon (e.g. the PREP deadline may occur much sooner than +the worst case since it depends on the CPU operating conditions, ie caches +state). + +An OS has to reliably probe the wakeup-latency since some devices can enforce +latency constraints guarantees to work properly, so the OS has to detect the +worst case wake-up latency it can incur if a CPU is allowed to enter an +idle state, and possibly to prevent that to guarantee reliable device +functioning. + +The min-residency time parameter deserves further explanation since it is +expressed in time units but must factor in energy consumption coefficients. + +The energy consumption of a cpu when it enters a power state can be roughly +characterised by the following graph: + + | + | + | + e | + n | /--- + e | /------ + r | /------ + g | /----- + y | /------ + | ---- + | /| + | / | + | / | + | / | + | / | + | / | + |/ | + -----|-------+---------------------------------- + 0| 1 time(ms) + + Graph 1: Energy vs time example + +The graph is split in two parts delimited by time 1ms on the X-axis. +The graph curve with X-axis values = { x | 0 < x < 1ms } has a steep slope +and denotes the energy costs incurred whilst entering and leaving the idle +state. +The graph curve in the area delimited by X-axis values = {x | x > 1ms } has +shallower slope and essentially represents the energy consumption of the idle +state. + +min-residency is defined for a given idle state as the minimum expected +residency time for a state (inclusive of preparation and entry) after +which choosing that state become the most energy efficient option. A good +way to visualise this, is by taking the same graph above and comparing some +states energy consumptions plots. + +For sake of simplicity, let's consider a system with two idle states IDLE1, +and IDLE2: + + | + | + | + | /-- IDLE1 + e | /--- + n | /---- + e | /--- + r | /-----/--------- IDLE2 + g | /-------/--------- + y | ------------ /---| + | / /---- | + | / /--- | + | / /---- | + | / /--- | + | --- | + | / | + | / | + |/ | time + ---/----------------------------+------------------------ + |IDLE1-energy < IDLE2-energy | IDLE2-energy < IDLE1-energy + | + IDLE2-min-residency + + Graph 2: idle states min-residency example + +In graph 2 above, that takes into account idle states entry/exit energy +costs, it is clear that if the idle state residency time (ie time till next +wake-up IRQ) is less than IDLE2-min-residency, IDLE1 is the better idle state +choice energywise. + +This is mainly down to the fact that IDLE1 entry/exit energy costs are lower +than IDLE2. + +However, the lower power consumption (ie shallower energy curve slope) of idle +state IDLE2 implies that after a suitable time, IDLE2 becomes more energy +efficient. + +The time at which IDLE2 becomes more energy efficient than IDLE1 (and other +shallower states in a system with multiple idle states) is defined +IDLE2-min-residency and corresponds to the time when energy consumption of +IDLE1 and IDLE2 states breaks even. + +The definitions provided in this section underpin the idle states +properties specification that is the subject of the following sections. + +=========================================== +3 - idle-states node +=========================================== + +ARM processor idle states are defined within the idle-states node, which is +a direct child of the cpus node [1] and provides a container where the +processor idle states, defined as device tree nodes, are listed. + +- idle-states node + + Usage: Optional - On ARM systems, it is a container of processor idle + states nodes. If the system does not provide CPU + power management capabilities or the processor just + supports idle_standby an idle-states node is not + required. + + Description: idle-states node is a container node, where its + subnodes describe the CPU idle states. + + Node name must be "idle-states". + + The idle-states node's parent node must be the cpus node. + + The idle-states node's child nodes can be: + + - one or more state nodes + + Any other configuration is considered invalid. + + An idle-states node defines the following properties: + + - entry-method + Value type: <stringlist> + Usage and definition depend on ARM architecture version. + # On ARM v8 64-bit this property is required and must + be one of: + - "psci" (see bindings in [2]) + # On ARM 32-bit systems this property is optional + +The nodes describing the idle states (state) can only be defined within the +idle-states node, any other configuration is considered invalid and therefore +must be ignored. + +=========================================== +4 - state node +=========================================== + +A state node represents an idle state description and must be defined as +follows: + +- state node + + Description: must be child of the idle-states node + + The state node name shall follow standard device tree naming + rules ([5], 2.2.1 "Node names"), in particular state nodes which + are siblings within a single common parent must be given a unique name. + + The idle state entered by executing the wfi instruction (idle_standby + SBSA,[3][4]) is considered standard on all ARM platforms and therefore + must not be listed. + + With the definitions provided above, the following list represents + the valid properties for a state node: + + - compatible + Usage: Required + Value type: <stringlist> + Definition: Must be "arm,idle-state". + + - local-timer-stop + Usage: See definition + Value type: <none> + Definition: if present the CPU local timer control logic is + lost on state entry, otherwise it is retained. + + - entry-latency-us + Usage: Required + Value type: <prop-encoded-array> + Definition: u32 value representing worst case latency in + microseconds required to enter the idle state. + The exit-latency-us duration may be guaranteed + only after entry-latency-us has passed. + + - exit-latency-us + Usage: Required + Value type: <prop-encoded-array> + Definition: u32 value representing worst case latency + in microseconds required to exit the idle state. + + - min-residency-us + Usage: Required + Value type: <prop-encoded-array> + Definition: u32 value representing minimum residency duration + in microseconds, inclusive of preparation and + entry, for this idle state to be considered + worthwhile energy wise (refer to section 2 of + this document for a complete description). + + - wakeup-latency-us: + Usage: Optional + Value type: <prop-encoded-array> + Definition: u32 value representing maximum delay between the + signaling of a wake-up event and the CPU being + able to execute normal code again. If omitted, + this is assumed to be equal to: + + entry-latency-us + exit-latency-us + + It is important to supply this value on systems + where the duration of PREP phase (see diagram 1, + section 2) is non-neglibigle. + In such systems entry-latency-us + exit-latency-us + will exceed wakeup-latency-us by this duration. + + In addition to the properties listed above, a state node may require + additional properties specifics to the entry-method defined in the + idle-states node, please refer to the entry-method bindings + documentation for properties definitions. + +=========================================== +4 - Examples +=========================================== + +Example 1 (ARM 64-bit, 16-cpu system, PSCI enable-method): + +cpus { + #size-cells = <0>; + #address-cells = <2>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x0>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0 + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>; + }; + + CPU1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x1>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0 + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>; + }; + + CPU2: cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x100>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0 + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>; + }; + + CPU3: cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x101>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0 + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>; + }; + + CPU4: cpu@10000 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x10000>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0 + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>; + }; + + CPU5: cpu@10001 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x10001>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0 + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>; + }; + + CPU6: cpu@10100 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x10100>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0 + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>; + }; + + CPU7: cpu@10101 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0 0x10101>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_0_0 &CPU_SLEEP_0_0 + &CLUSTER_RETENTION_0 &CLUSTER_SLEEP_0>; + }; + + CPU8: cpu@100000000 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1 0x0>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0 + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>; + }; + + CPU9: cpu@100000001 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1 0x1>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0 + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>; + }; + + CPU10: cpu@100000100 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1 0x100>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0 + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>; + }; + + CPU11: cpu@100000101 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1 0x101>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0 + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>; + }; + + CPU12: cpu@100010000 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1 0x10000>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0 + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>; + }; + + CPU13: cpu@100010001 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1 0x10001>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0 + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>; + }; + + CPU14: cpu@100010100 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1 0x10100>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0 + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>; + }; + + CPU15: cpu@100010101 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1 0x10101>; + enable-method = "psci"; + cpu-idle-states = <&CPU_RETENTION_1_0 &CPU_SLEEP_1_0 + &CLUSTER_RETENTION_1 &CLUSTER_SLEEP_1>; + }; + + idle-states { + entry-method = "arm,psci"; + + CPU_RETENTION_0_0: cpu-retention-0-0 { + compatible = "arm,idle-state"; + arm,psci-suspend-param = <0x0010000>; + entry-latency-us = <20>; + exit-latency-us = <40>; + min-residency-us = <80>; + }; + + CLUSTER_RETENTION_0: cluster-retention-0 { + compatible = "arm,idle-state"; + local-timer-stop; + arm,psci-suspend-param = <0x1010000>; + entry-latency-us = <50>; + exit-latency-us = <100>; + min-residency-us = <250>; + wakeup-latency-us = <130>; + }; + + CPU_SLEEP_0_0: cpu-sleep-0-0 { + compatible = "arm,idle-state"; + local-timer-stop; + arm,psci-suspend-param = <0x0010000>; + entry-latency-us = <250>; + exit-latency-us = <500>; + min-residency-us = <950>; + }; + + CLUSTER_SLEEP_0: cluster-sleep-0 { + compatible = "arm,idle-state"; + local-timer-stop; + arm,psci-suspend-param = <0x1010000>; + entry-latency-us = <600>; + exit-latency-us = <1100>; + min-residency-us = <2700>; + wakeup-latency-us = <1500>; + }; + + CPU_RETENTION_1_0: cpu-retention-1-0 { + compatible = "arm,idle-state"; + arm,psci-suspend-param = <0x0010000>; + entry-latency-us = <20>; + exit-latency-us = <40>; + min-residency-us = <90>; + }; + + CLUSTER_RETENTION_1: cluster-retention-1 { + compatible = "arm,idle-state"; + local-timer-stop; + arm,psci-suspend-param = <0x1010000>; + entry-latency-us = <50>; + exit-latency-us = <100>; + min-residency-us = <270>; + wakeup-latency-us = <100>; + }; + + CPU_SLEEP_1_0: cpu-sleep-1-0 { + compatible = "arm,idle-state"; + local-timer-stop; + arm,psci-suspend-param = <0x0010000>; + entry-latency-us = <70>; + exit-latency-us = <100>; + min-residency-us = <300>; + wakeup-latency-us = <150>; + }; + + CLUSTER_SLEEP_1: cluster-sleep-1 { + compatible = "arm,idle-state"; + local-timer-stop; + arm,psci-suspend-param = <0x1010000>; + entry-latency-us = <500>; + exit-latency-us = <1200>; + min-residency-us = <3500>; + wakeup-latency-us = <1300>; + }; + }; + +}; + +Example 2 (ARM 32-bit, 8-cpu system, two clusters): + +cpus { + #size-cells = <0>; + #address-cells = <1>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x0>; + cpu-idle-states = <&CPU_SLEEP_0_0 &CLUSTER_SLEEP_0>; + }; + + CPU1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x1>; + cpu-idle-states = <&CPU_SLEEP_0_0 &CLUSTER_SLEEP_0>; + }; + + CPU2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x2>; + cpu-idle-states = <&CPU_SLEEP_0_0 &CLUSTER_SLEEP_0>; + }; + + CPU3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x3>; + cpu-idle-states = <&CPU_SLEEP_0_0 &CLUSTER_SLEEP_0>; + }; + + CPU4: cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x100>; + cpu-idle-states = <&CPU_SLEEP_1_0 &CLUSTER_SLEEP_1>; + }; + + CPU5: cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x101>; + cpu-idle-states = <&CPU_SLEEP_1_0 &CLUSTER_SLEEP_1>; + }; + + CPU6: cpu@102 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x102>; + cpu-idle-states = <&CPU_SLEEP_1_0 &CLUSTER_SLEEP_1>; + }; + + CPU7: cpu@103 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x103>; + cpu-idle-states = <&CPU_SLEEP_1_0 &CLUSTER_SLEEP_1>; + }; + + idle-states { + CPU_SLEEP_0_0: cpu-sleep-0-0 { + compatible = "arm,idle-state"; + local-timer-stop; + entry-latency-us = <200>; + exit-latency-us = <100>; + min-residency-us = <400>; + wakeup-latency-us = <250>; + }; + + CLUSTER_SLEEP_0: cluster-sleep-0 { + compatible = "arm,idle-state"; + local-timer-stop; + entry-latency-us = <500>; + exit-latency-us = <1500>; + min-residency-us = <2500>; + wakeup-latency-us = <1700>; + }; + + CPU_SLEEP_1_0: cpu-sleep-1-0 { + compatible = "arm,idle-state"; + local-timer-stop; + entry-latency-us = <300>; + exit-latency-us = <500>; + min-residency-us = <900>; + wakeup-latency-us = <600>; + }; + + CLUSTER_SLEEP_1: cluster-sleep-1 { + compatible = "arm,idle-state"; + local-timer-stop; + entry-latency-us = <800>; + exit-latency-us = <2000>; + min-residency-us = <6500>; + wakeup-latency-us = <2300>; + }; + }; + +}; + +=========================================== +5 - References +=========================================== + +[1] ARM Linux Kernel documentation - CPUs bindings + Documentation/devicetree/bindings/arm/cpus.txt + +[2] ARM Linux Kernel documentation - PSCI bindings + Documentation/devicetree/bindings/arm/psci.txt + +[3] ARM Server Base System Architecture (SBSA) + http://infocenter.arm.com/help/index.jsp + +[4] ARM Architecture Reference Manuals + http://infocenter.arm.com/help/index.jsp + +[5] ePAPR standard + https://www.power.org/documentation/epapr-version-1-1/ diff --git a/Documentation/devicetree/bindings/arm/keystone/keystone.txt b/Documentation/devicetree/bindings/arm/keystone/keystone.txt index 63c0e6ae5cf7..59d7a46f85eb 100644 --- a/Documentation/devicetree/bindings/arm/keystone/keystone.txt +++ b/Documentation/devicetree/bindings/arm/keystone/keystone.txt @@ -8,3 +8,13 @@ Required properties: - compatible: All TI specific devices present in Keystone SOC should be in the form "ti,keystone-*". Generic devices like gic, arch_timers, ns16550 type UART should use the specified compatible for those devices. + +Boards: +- Keystone 2 Hawking/Kepler EVM + compatible = "ti,k2hk-evm","ti,keystone" + +- Keystone 2 Lamarr EVM + compatible = "ti,k2l-evm","ti,keystone" + +- Keystone 2 Edison EVM + compatible = "ti,k2e-evm","ti,keystone" diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt index b513cb8196fe..292ef7ca3058 100644 --- a/Documentation/devicetree/bindings/arm/l2cc.txt +++ b/Documentation/devicetree/bindings/arm/l2cc.txt @@ -2,6 +2,10 @@ ARM cores often have a separate level 2 cache controller. There are various implementations of the L2 cache controller with compatible programming models. +Some of the properties that are just prefixed "cache-*" are taken from section +3.7.3 of the ePAPR v1.1 specification which can be found at: +https://www.power.org/wp-content/uploads/2012/06/Power_ePAPR_APPROVED_v1.1.pdf + The ARM L2 cache representation in the device tree should be done as follows: Required properties: @@ -40,7 +44,16 @@ Optional properties: - arm,filter-ranges : <start length> Starting address and length of window to filter. Addresses in the filter window are directed to the M1 port. Other addresses will go to the M0 port. +- arm,io-coherent : indicates that the system is operating in an hardware + I/O coherent mode. Valid only when the arm,pl310-cache compatible + string is used. - interrupts : 1 combined interrupt. +- cache-size : specifies the size in bytes of the cache +- cache-sets : specifies the number of associativity sets of the cache +- cache-block-size : specifies the size in bytes of a cache block +- cache-line-size : specifies the size in bytes of a line in the cache, + if this is not specified, the line size is assumed to be equal to the + cache block size - cache-id-part: cache id part number to be used if it is not present on hardware - wt-override: If present then L2 is forced to Write through mode diff --git a/Documentation/devicetree/bindings/arm/marvell,berlin.txt b/Documentation/devicetree/bindings/arm/marvell,berlin.txt index 737afa5f8148..a99eb9eb14c0 100644 --- a/Documentation/devicetree/bindings/arm/marvell,berlin.txt +++ b/Documentation/devicetree/bindings/arm/marvell,berlin.txt @@ -12,6 +12,7 @@ SoC and board used. Currently known SoC compatibles are: "marvell,berlin2" for Marvell Armada 1500 (BG2, 88DE3100), "marvell,berlin2cd" for Marvell Armada 1500-mini (BG2CD, 88DE3005) "marvell,berlin2ct" for Marvell Armada ? (BG2CT, 88DE????) + "marvell,berlin2q" for Marvell Armada 1500-pro (BG2Q, 88DE3114) "marvell,berlin3" for Marvell Armada ? (BG3, 88DE????) * Example: @@ -22,3 +23,130 @@ SoC and board used. Currently known SoC compatibles are: ... } + +* Marvell Berlin CPU control bindings + +CPU control register allows various operations on CPUs, like resetting them +independently. + +Required properties: +- compatible: should be "marvell,berlin-cpu-ctrl" +- reg: address and length of the register set + +Example: + +cpu-ctrl@f7dd0000 { + compatible = "marvell,berlin-cpu-ctrl"; + reg = <0xf7dd0000 0x10000>; +}; + +* Marvell Berlin2 chip control binding + +Marvell Berlin SoCs have a chip control register set providing several +individual registers dealing with pinmux, padmux, clock, reset, and secondary +CPU boot address. Unfortunately, the individual registers are spread among the +chip control registers, so there should be a single DT node only providing the +different functions which are described below. + +Required properties: +- compatible: shall be one of + "marvell,berlin2-chip-ctrl" for BG2 + "marvell,berlin2cd-chip-ctrl" for BG2CD + "marvell,berlin2q-chip-ctrl" for BG2Q +- reg: address and length of following register sets for + BG2/BG2CD: chip control register set + BG2Q: chip control register set and cpu pll registers + +* Marvell Berlin2 system control binding + +Marvell Berlin SoCs have a system control register set providing several +individual registers dealing with pinmux, padmux, and reset. + +Required properties: +- compatible: should be one of + "marvell,berlin2-system-ctrl" for BG2 + "marvell,berlin2cd-system-ctrl" for BG2CD + "marvell,berlin2q-system-ctrl" for BG2Q +- reg: address and length of the system control register set + +* Clock provider binding + +As clock related registers are spread among the chip control registers, the +chip control node also provides the clocks. Marvell Berlin2 (BG2, BG2CD, BG2Q) +SoCs share the same IP for PLLs and clocks, with some minor differences in +features and register layout. + +Required properties: +- #clock-cells: shall be set to 1 +- clocks: clock specifiers referencing the core clock input clocks +- clock-names: array of strings describing the input clock specifiers above. + Allowed clock-names for the reference clocks are + "refclk" for the SoCs osciallator input on all SoCs, + and SoC-specific input clocks for + BG2/BG2CD: "video_ext0" for the external video clock input + +Clocks provided by core clocks shall be referenced by a clock specifier +indexing one of the provided clocks. Refer to dt-bindings/clock/berlin<soc>.h +for the corresponding index mapping. + +* Pin controller binding + +Pin control registers are part of both register sets, chip control and system +control. The pins controlled are organized in groups, so no actual pin +information is needed. + +A pin-controller node should contain subnodes representing the pin group +configurations, one per function. Each subnode has the group name and the muxing +function used. + +Be aware the Marvell Berlin datasheets use the keyword 'mode' for what is called +a 'function' in the pin-controller subsystem. + +Required subnode-properties: +- groups: a list of strings describing the group names. +- function: a string describing the function used to mux the groups. + +* Reset controller binding + +A reset controller is part of the chip control registers set. The chip control +node also provides the reset. The register set is not at the same offset between +Berlin SoCs. + +Required property: +- #reset-cells: must be set to 2 + +Example: + +chip: chip-control@ea0000 { + compatible = "marvell,berlin2-chip-ctrl"; + #clock-cells = <1>; + #reset-cells = <2>; + reg = <0xea0000 0x400>; + clocks = <&refclk>, <&externaldev 0>; + clock-names = "refclk", "video_ext0"; + + spi1_pmux: spi1-pmux { + groups = "G0"; + function = "spi1"; + }; +}; + +sysctrl: system-controller@d000 { + compatible = "marvell,berlin2-system-ctrl"; + reg = <0xd000 0x100>; + + uart0_pmux: uart0-pmux { + groups = "GSM4"; + function = "uart0"; + }; + + uart1_pmux: uart1-pmux { + groups = "GSM5"; + function = "uart1"; + }; + + uart2_pmux: uart2-pmux { + groups = "GSM3"; + function = "uart2"; + }; +}; diff --git a/Documentation/devicetree/bindings/arm/marvell,dove.txt b/Documentation/devicetree/bindings/arm/marvell,dove.txt new file mode 100644 index 000000000000..aaaf64c56e44 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/marvell,dove.txt @@ -0,0 +1,22 @@ +Marvell Dove Platforms Device Tree Bindings +----------------------------------------------- + +Boards with a Marvell Dove SoC shall have the following properties: + +Required root node property: +- compatible: must contain "marvell,dove"; + +* Global Configuration registers + +Global Configuration registers of Dove SoC are shared by a syscon node. + +Required properties: +- compatible: must contain "marvell,dove-global-config" and "syscon". +- reg: base address and size of the Global Configuration registers. + +Example: + +gconf: global-config@e802c { + compatible = "marvell,dove-global-config", "syscon"; + reg = <0xe802c 0x14>; +}; diff --git a/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt b/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt new file mode 100644 index 000000000000..925ecbf6e7b7 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt @@ -0,0 +1,97 @@ +Marvell Kirkwood SoC Family Device Tree Bindings +------------------------------------------------ + +Boards with a SoC of the Marvell Kirkwook family, eg 88f6281 + +* Required root node properties: +compatible: must contain "marvell,kirkwood" + +In addition, the above compatible shall be extended with the specific +SoC. Currently known SoC compatibles are: + +"marvell,kirkwood-88f6192" +"marvell,kirkwood-88f6281" +"marvell,kirkwood-88f6282" +"marvell,kirkwood-88f6283" +"marvell,kirkwood-88f6702" +"marvell,kirkwood-98DX4122" + +And in addition, the compatible shall be extended with the specific +board. Currently known boards are: + +"buffalo,lschlv2" +"buffalo,lsxhl" +"buffalo,lsxl" +"dlink,dns-320" +"dlink,dns-320-a1" +"dlink,dns-325" +"dlink,dns-325-a1" +"dlink,dns-kirkwood" +"excito,b3" +"globalscale,dreamplug-003-ds2001" +"globalscale,guruplug" +"globalscale,guruplug-server-plus" +"globalscale,sheevaplug" +"globalscale,sheevaplug" +"globalscale,sheevaplug-esata" +"globalscale,sheevaplug-esata-rev13" +"iom,iconnect" +"iom,iconnect-1.1" +"iom,ix2-200" +"keymile,km_kirkwood" +"lacie,cloudbox" +"lacie,inetspace_v2" +"lacie,laplug" +"lacie,netspace_lite_v2" +"lacie,netspace_max_v2" +"lacie,netspace_mini_v2" +"lacie,netspace_v2" +"marvell,db-88f6281-bp" +"marvell,db-88f6282-bp" +"marvell,mv88f6281gtw-ge" +"marvell,rd88f6281" +"marvell,rd88f6281" +"marvell,rd88f6281-a0" +"marvell,rd88f6281-a1" +"mpl,cec4" +"mpl,cec4-10" +"netgear,readynas" +"netgear,readynas" +"netgear,readynas-duo-v2" +"netgear,readynas-nv+-v2" +"plathome,openblocks-a6" +"plathome,openblocks-a7" +"raidsonic,ib-nas6210" +"raidsonic,ib-nas6210-b" +"raidsonic,ib-nas6220" +"raidsonic,ib-nas6220-b" +"raidsonic,ib-nas62x0" +"seagate,dockstar" +"seagate,goflexnet" +"synology,ds109" +"synology,ds110jv10" +"synology,ds110jv20" +"synology,ds110jv30" +"synology,ds111" +"synology,ds209" +"synology,ds210jv10" +"synology,ds210jv20" +"synology,ds212" +"synology,ds212jv10" +"synology,ds212jv20" +"synology,ds212pv10" +"synology,ds409" +"synology,ds409slim" +"synology,ds410j" +"synology,ds411" +"synology,ds411j" +"synology,ds411slim" +"synology,ds413jv10" +"synology,rs212" +"synology,rs409" +"synology,rs411" +"synology,rs812" +"usi,topkick" +"usi,topkick-1281P2" +"zyxel,nsa310" +"zyxel,nsa310a" diff --git a/Documentation/devicetree/bindings/arm/mediatek.txt b/Documentation/devicetree/bindings/arm/mediatek.txt new file mode 100644 index 000000000000..3be40139cfbb --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mediatek.txt @@ -0,0 +1,27 @@ +MediaTek mt65xx & mt81xx Platforms Device Tree Bindings + +Boards with a MediaTek mt65xx/mt81xx SoC shall have the following property: + +Required root node property: + +compatible: Must contain one of + "mediatek,mt6589" + "mediatek,mt6592" + "mediatek,mt8127" + "mediatek,mt8135" + + +Supported boards: + +- bq Aquaris5 smart phone: + Required root node properties: + - compatible = "mundoreader,bq-aquaris5", "mediatek,mt6589"; +- Evaluation board for MT6592: + Required root node properties: + - compatible = "mediatek,mt6592-evb", "mediatek,mt6592"; +- MTK mt8127 tablet moose EVB: + Required root node properties: + - compatible = "mediatek,mt8127-moose", "mediatek,mt8127"; +- MTK mt8135 tablet EVB: + Required root node properties: + - compatible = "mediatek,mt8135-evbp1", "mediatek,mt8135"; diff --git a/Documentation/devicetree/bindings/arm/mrvl/feroceon.txt b/Documentation/devicetree/bindings/arm/mrvl/feroceon.txt new file mode 100644 index 000000000000..0d244b999d10 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mrvl/feroceon.txt @@ -0,0 +1,16 @@ +* Marvell Feroceon Cache + +Required properties: +- compatible : Should be either "marvell,feroceon-cache" or + "marvell,kirkwood-cache". + +Optional properties: +- reg : Address of the L2 cache control register. Mandatory for + "marvell,kirkwood-cache", not used by "marvell,feroceon-cache" + + +Example: + l2: l2-cache@20128 { + compatible = "marvell,kirkwood-cache"; + reg = <0x20128 0x4>; + }; diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt new file mode 100644 index 000000000000..1333db9acfee --- /dev/null +++ b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt @@ -0,0 +1,30 @@ +Krait Processor Sub-system (KPSS) Application Clock Controller (ACC) + +The KPSS ACC provides clock, power domain, and reset control to a Krait CPU. +There is one ACC register region per CPU within the KPSS remapped region as +well as an alias register region that remaps accesses to the ACC associated +with the CPU accessing the region. + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: should be one of: + "qcom,kpss-acc-v1" + "qcom,kpss-acc-v2" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the first element specifies the base address and size of + the register region. An optional second element specifies + the base address and size of the alias register region. + +Example: + + clock-controller@2088000 { + compatible = "qcom,kpss-acc-v2"; + reg = <0x02088000 0x1000>, + <0x02008000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt b/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt new file mode 100644 index 000000000000..1505fb8e131a --- /dev/null +++ b/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt @@ -0,0 +1,35 @@ +SPM AVS Wrapper 2 (SAW2) + +The SAW2 is a wrapper around the Subsystem Power Manager (SPM) and the +Adaptive Voltage Scaling (AVS) hardware. The SPM is a programmable +micro-controller that transitions a piece of hardware (like a processor or +subsystem) into and out of low power modes via a direct connection to +the PMIC. It can also be wired up to interact with other processors in the +system, notifying them when a low power state is entered or exited. + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: shall contain "qcom,saw2". A more specific value should be + one of: + "qcom,saw2-v1" + "qcom,saw2-v1.1" + "qcom,saw2-v2" + "qcom,saw2-v2.1" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the first element specifies the base address and size of + the register region. An optional second element specifies + the base address and size of the alias register region. + + +Example: + + regulator@2099000 { + compatible = "qcom,saw2"; + reg = <0x02099000 0x1000>, <0x02009000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/arm/mvebu-system-controller.txt b/Documentation/devicetree/bindings/arm/mvebu-system-controller.txt index 081c6a786c8a..d24ab2ebf8a7 100644 --- a/Documentation/devicetree/bindings/arm/mvebu-system-controller.txt +++ b/Documentation/devicetree/bindings/arm/mvebu-system-controller.txt @@ -1,12 +1,13 @@ MVEBU System Controller ----------------------- -MVEBU (Marvell SOCs: Armada 370/XP, Dove, mv78xx0, Kirkwood, Orion5x) +MVEBU (Marvell SOCs: Armada 370/375/XP, Dove, mv78xx0, Kirkwood, Orion5x) Required properties: - compatible: one of: - "marvell,orion-system-controller" - "marvell,armada-370-xp-system-controller" + - "marvell,armada-375-system-controller" - reg: Should contain system controller registers location and length. Example: diff --git a/Documentation/devicetree/bindings/arm/omap/crossbar.txt b/Documentation/devicetree/bindings/arm/omap/crossbar.txt new file mode 100644 index 000000000000..4139db353d0a --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/crossbar.txt @@ -0,0 +1,63 @@ +Some socs have a large number of interrupts requests to service +the needs of its many peripherals and subsystems. All of the +interrupt lines from the subsystems are not needed at the same +time, so they have to be muxed to the irq-controller appropriately. +In such places a interrupt controllers are preceded by an CROSSBAR +that provides flexibility in muxing the device requests to the controller +inputs. + +Required properties: +- compatible : Should be "ti,irq-crossbar" +- reg: Base address and the size of the crossbar registers. +- ti,max-irqs: Total number of irqs available at the interrupt controller. +- ti,max-crossbar-sources: Maximum number of crossbar sources that can be routed. +- ti,reg-size: Size of a individual register in bytes. Every individual + register is assumed to be of same size. Valid sizes are 1, 2, 4. +- ti,irqs-reserved: List of the reserved irq lines that are not muxed using + crossbar. These interrupt lines are reserved in the soc, + so crossbar bar driver should not consider them as free + lines. + +Optional properties: +- ti,irqs-skip: This is similar to "ti,irqs-reserved", but these are for + SOC-specific hard-wiring of those irqs which unexpectedly bypasses the + crossbar. These irqs have a crossbar register, but still cannot be used. + +- ti,irqs-safe-map: integer which maps to a safe configuration to use + when the interrupt controller irq is unused (when not provided, default is 0) + +Examples: + crossbar_mpu: @4a020000 { + compatible = "ti,irq-crossbar"; + reg = <0x4a002a48 0x130>; + ti,max-irqs = <160>; + ti,max-crossbar-sources = <400>; + ti,reg-size = <2>; + ti,irqs-reserved = <0 1 2 3 5 6 131 132 139 140>; + ti,irqs-skip = <10 133 139 140>; + }; + +Consumer: +======== +See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt and +Documentation/devicetree/bindings/arm/gic.txt for further details. + +An interrupt consumer on an SoC using crossbar will use: + interrupts = <GIC_SPI request_number interrupt_level> +When the request number is between 0 to that described by +"ti,max-crossbar-sources", it is assumed to be a crossbar mapping. If the +request_number is greater than "ti,max-crossbar-sources", then it is mapped as a +quirky hardware mapping direct to GIC. + +Example: + device_x@0x4a023000 { + /* Crossbar 8 used */ + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; + ... + }; + + device_y@0x4a033000 { + /* Direct mapped GIC SPI 1 used */ + interrupts = <GIC_SPI DIRECT_IRQ(1) IRQ_TYPE_LEVEL_HIGH>; + ... + }; diff --git a/Documentation/devicetree/bindings/arm/omap/dmm.txt b/Documentation/devicetree/bindings/arm/omap/dmm.txt new file mode 100644 index 000000000000..8bd6d0a238a8 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/dmm.txt @@ -0,0 +1,22 @@ +OMAP Dynamic Memory Manager (DMM) bindings + +The dynamic memory manager (DMM) is a module located immediately in front of the +SDRAM controllers (called EMIFs on OMAP). DMM manages various aspects of memory +accesses such as priority generation amongst initiators, configuration of SDRAM +interleaving, optimizing transfer of 2D block objects, and provide MMU-like page +translation for initiators which need contiguous dma bus addresses. + +Required properties: +- compatible: Should contain "ti,omap4-dmm" for OMAP4 family + Should contain "ti,omap5-dmm" for OMAP5 and DRA7x family +- reg: Contains DMM register address range (base address and length) +- interrupts: Should contain an interrupt-specifier for DMM_IRQ. +- ti,hwmods: Name of the hwmod associated to DMM, which is typically "dmm" + +Example: + +dmm@4e000000 { + compatible = "ti,omap4-dmm"; + reg = <0x4e000000 0x800>; + ti,hwmods = "dmm"; +}; diff --git a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt index c0105de55cbd..974624ea68f6 100644 --- a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt +++ b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt @@ -6,6 +6,8 @@ provided by Arteris. Required properties: - compatible : Should be "ti,omap3-l3-smx" for OMAP3 family Should be "ti,omap4-l3-noc" for OMAP4 family + Should be "ti,dra7-l3-noc" for DRA7 family + Should be "ti,am4372-l3-noc" for AM43 family - reg: Contains L3 register address range for each noc domain. - ti,hwmods: "l3_main_1", ... One hwmod for each noc domain. diff --git a/Documentation/devicetree/bindings/arm/omap/mpu.txt b/Documentation/devicetree/bindings/arm/omap/mpu.txt index 83f405bde138..763695db2bd9 100644 --- a/Documentation/devicetree/bindings/arm/omap/mpu.txt +++ b/Documentation/devicetree/bindings/arm/omap/mpu.txt @@ -10,6 +10,9 @@ Required properties: Should be "ti,omap5-mpu" for OMAP5 - ti,hwmods: "mpu" +Optional properties: +- sram: Phandle to the ocmcram node + Examples: - For an OMAP5 SMP system: diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 34dc40cffdfd..4f6a82cef1d1 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -80,7 +80,22 @@ SoCs: compatible = "ti,omap5432", "ti,omap5" - DRA742 - compatible = "ti,dra7xx", "ti,dra7" + compatible = "ti,dra742", "ti,dra74", "ti,dra7" + +- DRA722 + compatible = "ti,dra722", "ti,dra72", "ti,dra7" + +- AM5728 + compatible = "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7" + +- AM5726 + compatible = "ti,am5726", "ti,dra742", "ti,dra74", "ti,dra7" + +- AM5718 + compatible = "ti,am5718", "ti,dra722", "ti,dra72", "ti,dra7" + +- AM5716 + compatible = "ti,am5716", "ti,dra722", "ti,dra72", "ti,dra7" - AM4372 compatible = "ti,am4372", "ti,am43" @@ -91,7 +106,7 @@ Boards: compatible = "ti,omap3-beagle", "ti,omap3" - OMAP3 Tobi with Overo : Commercial expansion board with daughter board - compatible = "ti,omap3-tobi", "ti,omap3-overo", "ti,omap3" + compatible = "gumstix,omap3-overo-tobi", "gumstix,omap3-overo", "ti,omap3" - OMAP4 SDP : Software Development Board compatible = "ti,omap4-sdp", "ti,omap4430" @@ -99,6 +114,15 @@ Boards: - OMAP4 PandaBoard : Low cost community board compatible = "ti,omap4-panda", "ti,omap4430" +- OMAP4 DuoVero with Parlor : Commercial expansion board with daughter board + compatible = "gumstix,omap4-duovero-parlor", "gumstix,omap4-duovero", "ti,omap4430", "ti,omap4"; + +- OMAP4 VAR-STK-OM44 : Commercial dev kit with VAR-OM44CustomBoard and VAR-SOM-OM44 w/WLAN + compatible = "variscite,var-stk-om44", "variscite,var-som-om44", "ti,omap4460", "ti,omap4"; + +- OMAP4 VAR-DVK-OM44 : Commercial dev kit with VAR-OM44CustomBoard, VAR-SOM-OM44 w/WLAN and LCD touchscreen + compatible = "variscite,var-dvk-om44", "variscite,var-som-om44", "ti,omap4460", "ti,omap4"; + - OMAP3 EVM : Software Development Board for OMAP35x, AM/DM37x compatible = "ti,omap3-evm", "ti,omap3" @@ -108,11 +132,23 @@ Boards: - AM335X Bone : Low cost community board compatible = "ti,am335x-bone", "ti,am33xx", "ti,omap3" +- AM335X OrionLXm : Substation Automation Platform + compatible = "novatech,am335x-lxm", "ti,am33xx" + - OMAP5 EVM : Evaluation Module compatible = "ti,omap5-evm", "ti,omap5" - AM43x EPOS EVM compatible = "ti,am43x-epos-evm", "ti,am4372", "ti,am43" -- DRA7 EVM: Software Developement Board for DRA7XX - compatible = "ti,dra7-evm", "ti,dra7" +- AM437x GP EVM + compatible = "ti,am437x-gp-evm", "ti,am4372", "ti,am43" + +- AM437x SK EVM: AM437x StarterKit Evaluation Module + compatible = "ti,am437x-sk-evm", "ti,am4372", "ti,am43" + +- DRA742 EVM: Software Development Board for DRA742 + compatible = "ti,dra7-evm", "ti,dra742", "ti,dra74", "ti,dra7" + +- DRA722 EVM: Software Development Board for DRA722 + compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7" diff --git a/Documentation/devicetree/bindings/arm/omap/prcm.txt b/Documentation/devicetree/bindings/arm/omap/prcm.txt new file mode 100644 index 000000000000..79074dac684a --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/prcm.txt @@ -0,0 +1,65 @@ +OMAP PRCM bindings + +Power Reset and Clock Manager lists the device clocks and clockdomains under +a DT hierarchy. Each TI SoC can have multiple PRCM entities listed for it, +each describing one module and the clock hierarchy under it. see [1] for +documentation about the individual clock/clockdomain nodes. + +[1] Documentation/devicetree/bindings/clock/ti/* + +Required properties: +- compatible: Must be one of: + "ti,am3-prcm" + "ti,am3-scrm" + "ti,am4-prcm" + "ti,am4-scrm" + "ti,omap2-prcm" + "ti,omap2-scrm" + "ti,omap3-prm" + "ti,omap3-cm" + "ti,omap3-scrm" + "ti,omap4-cm1" + "ti,omap4-prm" + "ti,omap4-cm2" + "ti,omap4-scrm" + "ti,omap5-prm" + "ti,omap5-cm-core-aon" + "ti,omap5-scrm" + "ti,omap5-cm-core" + "ti,dra7-prm" + "ti,dra7-cm-core-aon" + "ti,dra7-cm-core" +- reg: Contains PRCM module register address range + (base address and length) +- clocks: clocks for this module +- clockdomains: clockdomains for this module + +Example: + +cm: cm@48004000 { + compatible = "ti,omap3-cm"; + reg = <0x48004000 0x4000>; + + cm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + cm_clockdomains: clockdomains { + }; +} + +&cm_clocks { + omap2_32k_fck: omap_32k_fck { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32768>; + }; +}; + +&cm_clockdomains { + core_l3_clkdm: core_l3_clkdm { + compatible = "ti,clockdomain"; + clocks = <&sdrc_ick>; + }; +}; diff --git a/Documentation/devicetree/bindings/arm/pmu.txt b/Documentation/devicetree/bindings/arm/pmu.txt index 3e1e498fea96..75ef91d08f3b 100644 --- a/Documentation/devicetree/bindings/arm/pmu.txt +++ b/Documentation/devicetree/bindings/arm/pmu.txt @@ -8,7 +8,9 @@ Required properties: - compatible : should be one of "arm,armv8-pmuv3" + "arm,cortex-a17-pmu" "arm,cortex-a15-pmu" + "arm,cortex-a12-pmu" "arm,cortex-a9-pmu" "arm,cortex-a8-pmu" "arm,cortex-a7-pmu" @@ -16,7 +18,14 @@ Required properties: "arm,arm11mpcore-pmu" "arm,arm1176-pmu" "arm,arm1136-pmu" -- interrupts : 1 combined interrupt or 1 per core. + "qcom,krait-pmu" +- interrupts : 1 combined interrupt or 1 per core. If the interrupt is a per-cpu + interrupt (PPI) then 1 interrupt should be specified. + +Optional properties: + +- qcom,no-pc-write : Indicates that this PMU doesn't support the 0xc and 0xd + events. Example: diff --git a/Documentation/devicetree/bindings/arm/psci.txt b/Documentation/devicetree/bindings/arm/psci.txt index 433afe9cb590..5aa40ede0e99 100644 --- a/Documentation/devicetree/bindings/arm/psci.txt +++ b/Documentation/devicetree/bindings/arm/psci.txt @@ -21,7 +21,15 @@ to #0. Main node required properties: - - compatible : Must be "arm,psci" + - compatible : should contain at least one of: + + * "arm,psci" : for implementations complying to PSCI versions prior to + 0.2. For these cases function IDs must be provided. + + * "arm,psci-0.2" : for implementations complying to PSCI 0.2. Function + IDs are not required and should be ignored by an OS with PSCI 0.2 + support, but are permitted to be present for compatibility with + existing software when "arm,psci" is later in the compatible list. - method : The method of calling the PSCI firmware. Permitted values are: @@ -42,9 +50,21 @@ Main node optional properties: - migrate : Function ID for MIGRATE operation +Device tree nodes that require usage of PSCI CPU_SUSPEND function (ie idle +state nodes, as per bindings in [1]) must specify the following properties: + +- arm,psci-suspend-param + Usage: Required for state nodes[1] if the corresponding + idle-states node entry-method property is set + to "psci". + Value type: <u32> + Definition: power_state parameter to pass to the PSCI + suspend call. Example: +Case 1: PSCI v0.1 only. + psci { compatible = "arm,psci"; method = "smc"; @@ -53,3 +73,30 @@ Example: cpu_on = <0x95c10002>; migrate = <0x95c10003>; }; + +Case 2: PSCI v0.2 only + + psci { + compatible = "arm,psci-0.2"; + method = "smc"; + }; + +Case 3: PSCI v0.2 and PSCI v0.1. + + A DTB may provide IDs for use by kernels without PSCI 0.2 support, + enabling firmware and hypervisors to support existing and new kernels. + These IDs will be ignored by kernels with PSCI 0.2 support, which will + use the standard PSCI 0.2 IDs exclusively. + + psci { + compatible = "arm,psci-0.2", "arm,psci"; + method = "hvc"; + + cpu_on = < arbitrary value >; + cpu_off = < arbitrary value >; + + ... + }; + +[1] Kernel documentation - ARM idle states bindings + Documentation/devicetree/bindings/arm/idle-states.txt diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt new file mode 100644 index 000000000000..eaa3d1a0eb05 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -0,0 +1,14 @@ +Rockchip platforms device tree bindings +--------------------------------------- + +- MarsBoard RK3066 board: + Required root node properties: + - compatible = "haoyu,marsboard-rk3066", "rockchip,rk3066a"; + +- bq Curie 2 tablet: + Required root node properties: + - compatible = "mundoreader,bq-curie2", "rockchip,rk3066a"; + +- Radxa Rock board: + Required root node properties: + - compatible = "radxa,rock", "rockchip,rk3188"; diff --git a/Documentation/devicetree/bindings/arm/rockchip/pmu.txt b/Documentation/devicetree/bindings/arm/rockchip/pmu.txt new file mode 100644 index 000000000000..3ee9b428b2f7 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/rockchip/pmu.txt @@ -0,0 +1,16 @@ +Rockchip power-management-unit: +------------------------------- + +The pmu is used to turn off and on different power domains of the SoCs +This includes the power to the CPU cores. + +Required node properties: +- compatible value : = "rockchip,rk3066-pmu"; +- reg : physical base address and the size of the registers window + +Example: + + pmu@20004000 { + compatible = "rockchip,rk3066-pmu"; + reg = <0x20004000 0x100>; + }; diff --git a/Documentation/devicetree/bindings/arm/rockchip/smp-sram.txt b/Documentation/devicetree/bindings/arm/rockchip/smp-sram.txt new file mode 100644 index 000000000000..d9416fb8db6f --- /dev/null +++ b/Documentation/devicetree/bindings/arm/rockchip/smp-sram.txt @@ -0,0 +1,30 @@ +Rockchip SRAM for smp bringup: +------------------------------ + +Rockchip's smp-capable SoCs use the first part of the sram for the bringup +of the cores. Once the core gets powered up it executes the code that is +residing at the very beginning of the sram. + +Therefore a reserved section sub-node has to be added to the mmio-sram +declaration. + +Required sub-node properties: +- compatible : should be "rockchip,rk3066-smp-sram" + +The rest of the properties should follow the generic mmio-sram discription +found in ../../misc/sram.txt + +Example: + + sram: sram@10080000 { + compatible = "mmio-sram"; + reg = <0x10080000 0x10000>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + smp-sram@10080000 { + compatible = "rockchip,rk3066-smp-sram"; + reg = <0x10080000 0x50>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung-boards.txt index 2168ed31e1b0..43589d2466a7 100644 --- a/Documentation/devicetree/bindings/arm/samsung-boards.txt +++ b/Documentation/devicetree/bindings/arm/samsung-boards.txt @@ -1,11 +1,20 @@ -* Samsung's Exynos4210 based SMDKV310 evaluation board - -SMDKV310 evaluation board is based on Samsung's Exynos4210 SoC. +* Samsung's Exynos SoC based boards Required root node properties: - compatible = should be one or more of the following. - (a) "samsung,smdkv310" - for Samsung's SMDKV310 eval board. - (b) "samsung,exynos4210" - for boards based on Exynos4210 SoC. + - "samsung,monk" - for Exynos3250-based Samsung Simband board. + - "samsung,rinato" - for Exynos3250-based Samsung Gear2 board. + - "samsung,smdkv310" - for Exynos4210-based Samsung SMDKV310 eval board. + - "samsung,trats" - for Exynos4210-based Tizen Reference board. + - "samsung,universal_c210" - for Exynos4210-based Samsung board. + - "samsung,smdk4412", - for Exynos4412-based Samsung SMDK4412 eval board. + - "samsung,trats2" - for Exynos4412-based Tizen Reference board. + - "samsung,smdk5250" - for Exynos5250-based Samsung SMDK5250 eval board. + - "samsung,xyref5260" - for Exynos5260-based Samsung board. + - "samsung,smdk5410" - for Exynos5410-based Samsung SMDK5410 eval board. + - "samsung,smdk5420" - for Exynos5420-based Samsung SMDK5420 eval board. + - "samsung,sd5v1" - for Exynos5440-based Samsung board. + - "samsung,ssdk5440" - for Exynos5440-based Samsung board. Optional: - firmware node, specifying presence and type of secure firmware: diff --git a/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt b/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt index 5d49f2b37f68..709efaa30841 100644 --- a/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt +++ b/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt @@ -11,17 +11,36 @@ New driver handles the following Required properties: - compatible: Must be "samsung,exynos-adc-v1" - for exynos4412/5250 controllers. + for exynos4412/5250 and s5pv210 controllers. Must be "samsung,exynos-adc-v2" for future controllers. -- reg: Contains ADC register address range (base address and - length) and the address of the phy enable register. + Must be "samsung,exynos3250-adc" for + controllers compatible with ADC of Exynos3250. + Must be "samsung,s3c2410-adc" for + the ADC in s3c2410 and compatibles + Must be "samsung,s3c2416-adc" for + the ADC in s3c2416 and compatibles + Must be "samsung,s3c2440-adc" for + the ADC in s3c2440 and compatibles + Must be "samsung,s3c2443-adc" for + the ADC in s3c2443 and compatibles + Must be "samsung,s3c6410-adc" for + the ADC in s3c6410 and compatibles +- reg: List of ADC register address range + - The base address and range of ADC register + - The base address and range of ADC_PHY register (every + SoC except for s3c24xx/s3c64xx ADC) - interrupts: Contains the interrupt information for the timer. The format is being dependent on which interrupt controller the Samsung device uses. - #io-channel-cells = <1>; As ADC has multiple outputs -- clocks From common clock binding: handle to adc clock. -- clock-names From common clock binding: Shall be "adc". +- clocks From common clock bindings: handles to clocks specified + in "clock-names" property, in the same order. +- clock-names From common clock bindings: list of clock input names + used by ADC block: + - "adc" : ADC bus clock + - "sclk" : ADC special clock (only for Exynos3250 and + compatible ADC block) - vdd-supply VDD input supply. Note: child nodes can be added for auto probing from device tree. @@ -41,6 +60,20 @@ adc: adc@12D10000 { vdd-supply = <&buck5_reg>; }; +Example: adding device info in dtsi file for Exynos3250 with additional sclk + +adc: adc@126C0000 { + compatible = "samsung,exynos3250-adc", "samsung,exynos-adc-v2; + reg = <0x126C0000 0x100>, <0x10020718 0x4>; + interrupts = <0 137 0>; + #io-channel-cells = <1>; + io-channel-ranges; + + clocks = <&cmu CLK_TSADC>, <&cmu CLK_SCLK_TSADC>; + clock-names = "adc", "sclk"; + + vdd-supply = <&buck5_reg>; +}; Example: Adding child nodes in dts file @@ -48,7 +81,7 @@ adc@12D10000 { /* NTC thermistor is a hwmon device */ ncp15wb473@0 { - compatible = "ntc,ncp15wb473"; + compatible = "murata,ncp15wb473"; pullup-uv = <1800000>; pullup-ohm = <47000>; pulldown-ohm = <0>; diff --git a/Documentation/devicetree/bindings/arm/samsung/pmu.txt b/Documentation/devicetree/bindings/arm/samsung/pmu.txt new file mode 100644 index 000000000000..1e1979b229ff --- /dev/null +++ b/Documentation/devicetree/bindings/arm/samsung/pmu.txt @@ -0,0 +1,51 @@ +SAMSUNG Exynos SoC series PMU Registers + +Properties: + - compatible : should contain two values. First value must be one from following list: + - "samsung,exynos3250-pmu" - for Exynos3250 SoC, + - "samsung,exynos4210-pmu" - for Exynos4210 SoC, + - "samsung,exynos4212-pmu" - for Exynos4212 SoC, + - "samsung,exynos4412-pmu" - for Exynos4412 SoC, + - "samsung,exynos5250-pmu" - for Exynos5250 SoC, + - "samsung,exynos5260-pmu" - for Exynos5260 SoC. + - "samsung,exynos5410-pmu" - for Exynos5410 SoC, + - "samsung,exynos5420-pmu" - for Exynos5420 SoC. + second value must be always "syscon". + + - reg : offset and length of the register set. + + - #clock-cells : must be <1>, since PMU requires once cell as clock specifier. + The single specifier cell is used as index to list of clocks + provided by PMU, which is currently: + 0 : SoC clock output (CLKOUT pin) + + - clock-names : list of clock names for particular CLKOUT mux inputs in + following format: + "clkoutN", where N is a decimal number corresponding to + CLKOUT mux control bits value for given input, e.g. + "clkout0", "clkout7", "clkout15". + + - clocks : list of phandles and specifiers to all input clocks listed in + clock-names property. + +Example : +pmu_system_controller: system-controller@10040000 { + compatible = "samsung,exynos5250-pmu", "syscon"; + reg = <0x10040000 0x5000>; + #clock-cells = <1>; + clock-names = "clkout0", "clkout1", "clkout2", "clkout3", + "clkout4", "clkout8", "clkout9"; + clocks = <&clock CLK_OUT_DMC>, <&clock CLK_OUT_TOP>, + <&clock CLK_OUT_LEFTBUS>, <&clock CLK_OUT_RIGHTBUS>, + <&clock CLK_OUT_CPU>, <&clock CLK_XXTI>, + <&clock CLK_XUSBXTI>; +}; + +Example of clock consumer : + +usb3503: usb3503@08 { + /* ... */ + clock-names = "refclk"; + clocks = <&pmu_system_controller 0>; + /* ... */ +}; diff --git a/Documentation/devicetree/bindings/arm/samsung/sysreg.txt b/Documentation/devicetree/bindings/arm/samsung/sysreg.txt index 0ab3251a6ec2..4fced6e9d5e4 100644 --- a/Documentation/devicetree/bindings/arm/samsung/sysreg.txt +++ b/Documentation/devicetree/bindings/arm/samsung/sysreg.txt @@ -1,8 +1,10 @@ SAMSUNG S5P/Exynos SoC series System Registers (SYSREG) Properties: - - compatible : should contain "samsung,<chip name>-sysreg", "syscon"; - For Exynos4 SoC series it should be "samsung,exynos4-sysreg", "syscon"; + - compatible : should contain two values. First value must be one from following list: + - "samsung,exynos4-sysreg" - for Exynos4 based SoCs, + - "samsung,exynos5-sysreg" - for Exynos5 based SoCs. + second value must be always "syscon". - reg : offset and length of the register set. Example: @@ -10,3 +12,8 @@ Example: compatible = "samsung,exynos4-sysreg", "syscon"; reg = <0x10010000 0x400>; }; + + syscon@10050000 { + compatible = "samsung,exynos5-sysreg", "syscon"; + reg = <0x10050000 0x5000>; + }; diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt new file mode 100644 index 000000000000..51147cb5c036 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/shmobile.txt @@ -0,0 +1,71 @@ +Renesas SH-Mobile, R-Mobile, and R-Car Platform Device Tree Bindings +-------------------------------------------------------------------- + +SoCs: + + - Emma Mobile EV2 + compatible = "renesas,emev2" + - RZ/A1H (R7S72100) + compatible = "renesas,r7s72100" + - SH-Mobile AP4 (R8A73720/SH7372) + compatible = "renesas,sh7372" + - SH-Mobile AG5 (R8A73A00/SH73A0) + compatible = "renesas,sh73a0" + - R-Mobile APE6 (R8A73A40) + compatible = "renesas,r8a73a4" + - R-Mobile A1 (R8A77400) + compatible = "renesas,r8a7740" + - R-Car M1A (R8A77781) + compatible = "renesas,r8a7778" + - R-Car H1 (R8A77790) + compatible = "renesas,r8a7779" + - R-Car H2 (R8A77900) + compatible = "renesas,r8a7790" + - R-Car M2-W (R8A77910) + compatible = "renesas,r8a7791" + - R-Car V2H (R8A77920) + compatible = "renesas,r8a7792" + - R-Car M2-N (R8A77930) + compatible = "renesas,r8a7793" + - R-Car E2 (R8A77940) + compatible = "renesas,r8a7794" + + +Boards: + + - Alt + compatible = "renesas,alt", "renesas,r8a7794" + - APE6-EVM + compatible = "renesas,ape6evm", "renesas,r8a73a4" + - APE6-EVM - Reference Device Tree Implementation + compatible = "renesas,ape6evm-reference", "renesas,r8a73a4" + - Atmark Techno Armadillo-800 EVA + compatible = "renesas,armadillo800eva" + - BOCK-W + compatible = "renesas,bockw", "renesas,r8a7778" + - BOCK-W - Reference Device Tree Implementation + compatible = "renesas,bockw-reference", "renesas,r8a7778" + - Genmai (RTK772100BC00000BR) + compatible = "renesas,genmai", "renesas,r7s72100" + - Gose + compatible = "renesas,gose", "renesas,r8a7793" + - Henninger + compatible = "renesas,henninger", "renesas,r8a7791" + - Koelsch (RTP0RC7791SEB00010S) + compatible = "renesas,koelsch", "renesas,r8a7791" + - Kyoto Microcomputer Co. KZM-A9-Dual + compatible = "renesas,kzm9d", "renesas,emev2" + - Kyoto Microcomputer Co. KZM-A9-GT + compatible = "renesas,kzm9g", "renesas,sh73a0" + - Kyoto Microcomputer Co. KZM-A9-GT - Reference Device Tree Implementation + compatible = "renesas,kzm9g-reference", "renesas,sh73a0" + - Lager (RTP0RC7790SEB00010S) + compatible = "renesas,lager", "renesas,r8a7790" + - Mackerel (R0P7372LC0016RL, AP4 EVM 2nd) + compatible = "renesas,mackerel" + - Marzen + compatible = "renesas,marzen", "renesas,r8a7779" + +Note: Reference Device Tree Implementations are temporary implementations + to ease the migration from platform devices to Device Tree, and are + intended to be removed in the future. diff --git a/Documentation/devicetree/bindings/arm/spear-misc.txt b/Documentation/devicetree/bindings/arm/spear-misc.txt new file mode 100644 index 000000000000..cf649827ffcd --- /dev/null +++ b/Documentation/devicetree/bindings/arm/spear-misc.txt @@ -0,0 +1,9 @@ +SPEAr Misc configuration +=========================== +SPEAr SOCs have some miscellaneous registers which are used to configure +few properties of different peripheral controllers. + +misc node required properties: + +- compatible Should be "st,spear1340-misc", "syscon". +- reg: Address range of misc space upto 8K diff --git a/Documentation/devicetree/bindings/arm/ste-nomadik.txt b/Documentation/devicetree/bindings/arm/ste-nomadik.txt index 6256ec31666d..2fdff5a806cf 100644 --- a/Documentation/devicetree/bindings/arm/ste-nomadik.txt +++ b/Documentation/devicetree/bindings/arm/ste-nomadik.txt @@ -10,6 +10,12 @@ Required root node property: src Boards with the Nomadik SoC include: +Nomadik NHK-15 board manufactured by ST Microelectronics: + +Required root node property: + +compatible="st,nomadik-nhk-15"; + S8815 "MiniKit" manufactured by Calao Systems: Required root node property: diff --git a/Documentation/devicetree/bindings/arm/sti.txt b/Documentation/devicetree/bindings/arm/sti.txt new file mode 100644 index 000000000000..92f16c78bb69 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/sti.txt @@ -0,0 +1,15 @@ +ST STi Platforms Device Tree Bindings +--------------------------------------- + +Boards with the ST STiH415 SoC shall have the following properties: +Required root node property: +compatible = "st,stih415"; + +Boards with the ST STiH416 SoC shall have the following properties: +Required root node property: +compatible = "st,stih416"; + +Boards with the ST STiH407 SoC shall have the following properties: +Required root node property: +compatible = "st,stih407"; + diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt new file mode 100644 index 000000000000..42941fdefb11 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/sunxi.txt @@ -0,0 +1,12 @@ +Allwinner sunXi Platforms Device Tree Bindings + +Each device tree must specify which Allwinner SoC it uses, +using one of the following compatible strings: + + allwinner,sun4i-a10 + allwinner,sun5i-a10s + allwinner,sun5i-a13 + allwinner,sun6i-a31 + allwinner,sun7i-a20 + allwinner,sun8i-a23 + allwinner,sun9i-a80 diff --git a/Documentation/devicetree/bindings/arm/tegra.txt b/Documentation/devicetree/bindings/arm/tegra.txt index 558ed4b4ef39..73278c6d2dc3 100644 --- a/Documentation/devicetree/bindings/arm/tegra.txt +++ b/Documentation/devicetree/bindings/arm/tegra.txt @@ -30,6 +30,8 @@ board-specific compatible values: nvidia,seaboard nvidia,ventana nvidia,whistler + toradex,apalis_t30 + toradex,apalis_t30-eval toradex,colibri_t20-512 toradex,iris diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-flowctrl.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-flowctrl.txt new file mode 100644 index 000000000000..ccf0adddc820 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-flowctrl.txt @@ -0,0 +1,12 @@ +NVIDIA Tegra Flow Controller + +Required properties: +- compatible: Should be "nvidia,tegra<chip>-flowctrl" +- reg: Should contain one register range (address and length) + +Example: + + flow-controller@60007000 { + compatible = "nvidia,tegra20-flowctrl"; + reg = <0x60007000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/arm/topology.txt b/Documentation/devicetree/bindings/arm/topology.txt index 4aa20e7a424e..1061faf5f602 100644 --- a/Documentation/devicetree/bindings/arm/topology.txt +++ b/Documentation/devicetree/bindings/arm/topology.txt @@ -75,9 +75,10 @@ The cpu-map node can only contain three types of child nodes: whose bindings are described in paragraph 3. -The nodes describing the CPU topology (cluster/core/thread) can only be -defined within the cpu-map node. -Any other configuration is consider invalid and therefore must be ignored. +The nodes describing the CPU topology (cluster/core/thread) can only +be defined within the cpu-map node and every core/thread in the system +must be defined within the topology. Any other configuration is +invalid and therefore must be ignored. =========================================== 2.1 - cpu-map child nodes naming convention diff --git a/Documentation/devicetree/bindings/arm/ux500/power_domain.txt b/Documentation/devicetree/bindings/arm/ux500/power_domain.txt new file mode 100644 index 000000000000..5679d1742d3e --- /dev/null +++ b/Documentation/devicetree/bindings/arm/ux500/power_domain.txt @@ -0,0 +1,35 @@ +* ST-Ericsson UX500 PM Domains + +UX500 supports multiple PM domains which are used to gate power to one or +more peripherals on the SOC. + +The implementation of PM domains for UX500 are based upon the generic PM domain +and use the corresponding DT bindings. + +==PM domain providers== + +Required properties: + - compatible: Must be "stericsson,ux500-pm-domains". + - #power-domain-cells : Number of cells in a power domain specifier, must be 1. + +Example: + pm_domains: pm_domains0 { + compatible = "stericsson,ux500-pm-domains"; + #power-domain-cells = <1>; + }; + +==PM domain consumers== + +Required properties: + - power-domains: A phandle and PM domain specifier. Below are the list of + valid specifiers: + + Index Specifier + ----- --------- + 0 DOMAIN_VAPE + +Example: + sdi0_per1@80126000 { + compatible = "arm,pl18x", "arm,primecell"; + power-domains = <&pm_domains DOMAIN_VAPE> + }; diff --git a/Documentation/devicetree/bindings/arm/vexpress-sysreg.txt b/Documentation/devicetree/bindings/arm/vexpress-sysreg.txt index 5580e9c4bd85..00318d083c9e 100644 --- a/Documentation/devicetree/bindings/arm/vexpress-sysreg.txt +++ b/Documentation/devicetree/bindings/arm/vexpress-sysreg.txt @@ -8,6 +8,8 @@ interrupt generation, MMC and NOR Flash control etc. Required node properties: - compatible value : = "arm,vexpress,sysreg"; - reg : physical base address and the size of the registers window + +Deprecated properties, replaced by GPIO subnodes (see below): - gpio-controller : specifies that the node is a GPIO controller - #gpio-cells : size of the GPIO specifier, should be 2: - first cell is the pseudo-GPIO line number: @@ -16,35 +18,86 @@ Required node properties: 2 - NOR FLASH WPn - second cell can take standard GPIO flags (currently ignored). +Control registers providing pseudo-GPIO lines must be represented +by subnodes, each of them requiring the following properties: +- compatible value : one of + "arm,vexpress-sysreg,sys_led" + "arm,vexpress-sysreg,sys_mci" + "arm,vexpress-sysreg,sys_flash" +- gpio-controller : makes the node a GPIO controller +- #gpio-cells : size of the GPIO specifier, must be 2: + - first cell is the function number: + - for sys_led : 0..7 = LED 0..7 + - for sys_mci : 0 = MMC CARDIN, 1 = MMC WPROT + - for sys_flash : 0 = NOR FLASH WPn + - second cell can take standard GPIO flags (currently ignored). + Example: v2m_sysreg: sysreg@10000000 { compatible = "arm,vexpress-sysreg"; reg = <0x10000000 0x1000>; - gpio-controller; - #gpio-cells = <2>; + + v2m_led_gpios: sys_led@08 { + compatible = "arm,vexpress-sysreg,sys_led"; + gpio-controller; + #gpio-cells = <2>; + }; + + v2m_mmc_gpios: sys_mci@48 { + compatible = "arm,vexpress-sysreg,sys_mci"; + gpio-controller; + #gpio-cells = <2>; + }; + + v2m_flash_gpios: sys_flash@4c { + compatible = "arm,vexpress-sysreg,sys_flash"; + gpio-controller; + #gpio-cells = <2>; + }; }; This block also can also act a bridge to the platform's configuration bus via "system control" interface, addressing devices with site number, position in the board stack, config controller, function and device -numbers - see motherboard's TRM for more details. - -The node describing a config device must refer to the sysreg node via -"arm,vexpress,config-bridge" phandle (can be also defined in the node's -parent) and relies on the board topology properties - see main vexpress -node documentation for more details. It must also define the following -property: -- arm,vexpress-sysreg,func : must contain two cells: - - first cell defines function number (eg. 1 for clock generator, - 2 for voltage regulators etc.) - - device number (eg. osc 0, osc 1 etc.) +numbers - see motherboard's TRM for more details. All configuration +controller accessible via this interface must reference the sysreg +node via "arm,vexpress,config-bridge" phandle and define appropriate +topology properties - see main vexpress node documentation for more +details. Each child of such node describes one function and must +define the following properties: +- compatible value : must be one of (corresponding to the TRM): + "arm,vexpress-amp" + "arm,vexpress-dvimode" + "arm,vexpress-energy" + "arm,vexpress-muxfpga" + "arm,vexpress-osc" + "arm,vexpress-power" + "arm,vexpress-reboot" + "arm,vexpress-reset" + "arm,vexpress-scc" + "arm,vexpress-shutdown" + "arm,vexpress-temp" + "arm,vexpress-volt" +- arm,vexpress-sysreg,func : must contain a set of two cells long groups: + - first cell of each group defines the function number + (eg. 1 for clock generator, 2 for voltage regulators etc.) + - second cell of each group defines device number (eg. osc 0, + osc 1 etc.) + - some functions (eg. energy meter, with its 64 bit long counter) + are using more than one function/device number pair Example: mcc { + compatible = "arm,vexpress,config-bus"; arm,vexpress,config-bridge = <&v2m_sysreg>; osc@0 { compatible = "arm,vexpress-osc"; arm,vexpress-sysreg,func = <1 0>; }; + + energy@0 { + compatible = "arm,vexpress-energy"; + arm,vexpress-sysreg,func = <13 0>, <13 1>; + }; }; diff --git a/Documentation/devicetree/bindings/arm/vexpress.txt b/Documentation/devicetree/bindings/arm/vexpress.txt index ae49161e478a..39844cd0bcce 100644 --- a/Documentation/devicetree/bindings/arm/vexpress.txt +++ b/Documentation/devicetree/bindings/arm/vexpress.txt @@ -80,12 +80,17 @@ but also control clock generators, voltage regulators, gather environmental data like temperature, power consumption etc. Even the video output switch (FPGA) is controlled that way. -Nodes describing devices controlled by this infrastructure should -point at the bridge device node: +The controllers are not mapped into normal memory address space +and must be accessed through bridges - other devices capable +of generating transactions on the configuration bus. + +The nodes describing configuration controllers must define +the following properties: +- compatible value: + compatible = "arm,vexpress,config-bus"; - bridge phandle: arm,vexpress,config-bridge = <phandle>; -This property can be also defined in a parent node (eg. for a DCC) -and is effective for all children. +and children describing available functions. Platform topology @@ -197,7 +202,7 @@ Example of a VE tile description (simplified) }; dcc { - compatible = "simple-bus"; + compatible = "arm,vexpress,config-bus"; arm,vexpress,config-bridge = <&v2m_sysreg>; osc@0 { diff --git a/Documentation/devicetree/bindings/arm/xilinx.txt b/Documentation/devicetree/bindings/arm/xilinx.txt index 6f1ed830b4f7..1f7995357888 100644 --- a/Documentation/devicetree/bindings/arm/xilinx.txt +++ b/Documentation/devicetree/bindings/arm/xilinx.txt @@ -1,7 +1,7 @@ -Xilinx Zynq EP107 Emulation Platform board +Xilinx Zynq Platforms Device Tree Bindings -This board is an emulation platform for the Zynq product which is -based on an ARM Cortex A9 processor. +Boards with Zynq-7000 SOC based on an ARM Cortex A9 processor +shall have the following properties. Required root node properties: - - compatible = "xlnx,zynq-ep107"; + - compatible = "xlnx,zynq-7000"; diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt index 89de1564950c..4ab09f2202d4 100644 --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -3,18 +3,75 @@ SATA nodes are defined to describe on-chip Serial ATA controllers. Each SATA controller should have its own node. +It is possible, but not required, to represent each port as a sub-node. +It allows to enable each port independently when dealing with multiple +PHYs. + Required properties: -- compatible : compatible list, contains "snps,spear-ahci" +- compatible : compatible string, one of: + - "allwinner,sun4i-a10-ahci" + - "hisilicon,hisi-ahci" + - "ibm,476gtr-ahci" + - "marvell,armada-380-ahci" + - "snps,dwc-ahci" + - "snps,exynos5440-ahci" + - "snps,spear-ahci" + - "generic-ahci" - interrupts : <interrupt mapping for SATA IRQ> - reg : <registers mapping> +Please note that when using "generic-ahci" you must also specify a SoC specific +compatible: + compatible = "manufacturer,soc-model-ahci", "generic-ahci"; + Optional properties: - dma-coherent : Present if dma operations are coherent +- clocks : a list of phandle + clock specifier pairs +- target-supply : regulator for SATA target power +- phys : reference to the SATA PHY node +- phy-names : must be "sata-phy" + +Required properties when using sub-nodes: +- #address-cells : number of cells to encode an address +- #size-cells : number of cells representing the size of an address + + +Sub-nodes required properties: +- reg : the port number +- phys : reference to the SATA PHY node + -Example: +Examples: sata@ffe08000 { compatible = "snps,spear-ahci"; reg = <0xffe08000 0x1000>; interrupts = <115>; - }; + + ahci: sata@01c18000 { + compatible = "allwinner,sun4i-a10-ahci"; + reg = <0x01c18000 0x1000>; + interrupts = <56>; + clocks = <&pll6 0>, <&ahb_gates 25>; + target-supply = <®_ahci_5v>; + }; + +With sub-nodes: + sata@f7e90000 { + compatible = "marvell,berlin2q-achi", "generic-ahci"; + reg = <0xe90000 0x1000>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&chip CLKID_SATA>; + #address-cells = <1>; + #size-cells = <0>; + + sata0: sata-port@0 { + reg = <0>; + phys = <&sata_phy 0>; + }; + + sata1: sata-port@1 { + reg = <1>; + phys = <&sata_phy 1>; + }; + }; diff --git a/Documentation/devicetree/bindings/ata/ahci-st.txt b/Documentation/devicetree/bindings/ata/ahci-st.txt new file mode 100644 index 000000000000..0574a77a0b9f --- /dev/null +++ b/Documentation/devicetree/bindings/ata/ahci-st.txt @@ -0,0 +1,31 @@ +STMicroelectronics STi SATA controller + +This binding describes a SATA device. + +Required properties: + - compatible : Must be "st,sti-ahci" + - reg : Physical base addresses and length of register sets + - interrupts : Interrupt associated with the SATA device + - interrupt-names : Associated name must be; "hostc" + - resets : The power-down and soft-reset lines of SATA IP + - reset-names : Associated names must be; "pwr-dwn" and "sw-rst" + - clocks : The phandle for the clock + - clock-names : Associated name must be; "ahci_clk" + - phys : The phandle for the PHY device + - phy-names : Associated name must be; "ahci_phy" + +Example: + + sata0: sata@fe380000 { + compatible = "st,sti-ahci"; + reg = <0xfe380000 0x1000>; + interrupts = <GIC_SPI 157 IRQ_TYPE_NONE>; + interrupt-names = "hostc"; + phys = <&miphy365x_phy MIPHY_PORT_0 MIPHY_TYPE_SATA>; + phy-names = "ahci_phy"; + resets = <&powerdown STIH416_SATA0_POWERDOWN>, + <&softreset STIH416_SATA0_SOFTRESET>; + reset-names = "pwr-dwn", "sw-rst"; + clocks = <&clk_s_a0_ls CLK_ICN_REG>; + clock-names = "ahci_clk"; + }; diff --git a/Documentation/devicetree/bindings/ata/apm-xgene.txt b/Documentation/devicetree/bindings/ata/apm-xgene.txt new file mode 100644 index 000000000000..a668f0e7d001 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/apm-xgene.txt @@ -0,0 +1,79 @@ +* APM X-Gene 6.0 Gb/s SATA host controller nodes + +SATA host controller nodes are defined to describe on-chip Serial ATA +controllers. Each SATA controller (pair of ports) have its own node. + +Required properties: +- compatible : Shall contain: + * "apm,xgene-ahci" +- reg : First memory resource shall be the AHCI memory + resource. + Second memory resource shall be the host controller + core memory resource. + Third memory resource shall be the host controller + diagnostic memory resource. + 4th memory resource shall be the host controller + AXI memory resource. + 5th optional memory resource shall be the host + controller MUX memory resource if required. +- interrupts : Interrupt-specifier for SATA host controller IRQ. +- clocks : Reference to the clock entry. +- phys : A list of phandles + phy-specifiers, one for each + entry in phy-names. +- phy-names : Should contain: + * "sata-phy" for the SATA 6.0Gbps PHY + +Optional properties: +- dma-coherent : Present if dma operations are coherent +- status : Shall be "ok" if enabled or "disabled" if disabled. + Default is "ok". + +Example: + sataclk: sataclk { + compatible = "fixed-clock"; + #clock-cells = <1>; + clock-frequency = <100000000>; + clock-output-names = "sataclk"; + }; + + phy2: phy@1f22a000 { + compatible = "apm,xgene-phy"; + reg = <0x0 0x1f22a000 0x0 0x100>; + #phy-cells = <1>; + }; + + phy3: phy@1f23a000 { + compatible = "apm,xgene-phy"; + reg = <0x0 0x1f23a000 0x0 0x100>; + #phy-cells = <1>; + }; + + sata2: sata@1a400000 { + compatible = "apm,xgene-ahci"; + reg = <0x0 0x1a400000 0x0 0x1000>, + <0x0 0x1f220000 0x0 0x1000>, + <0x0 0x1f22d000 0x0 0x1000>, + <0x0 0x1f22e000 0x0 0x1000>, + <0x0 0x1f227000 0x0 0x1000>; + interrupts = <0x0 0x87 0x4>; + dma-coherent; + status = "ok"; + clocks = <&sataclk 0>; + phys = <&phy2 0>; + phy-names = "sata-phy"; + }; + + sata3: sata@1a800000 { + compatible = "apm,xgene-ahci-pcie"; + reg = <0x0 0x1a800000 0x0 0x1000>, + <0x0 0x1f230000 0x0 0x1000>, + <0x0 0x1f23d000 0x0 0x1000>, + <0x0 0x1f23e000 0x0 0x1000>, + <0x0 0x1f237000 0x0 0x1000>; + interrupts = <0x0 0x88 0x4>; + dma-coherent; + status = "ok"; + clocks = <&sataclk 0>; + phys = <&phy3 0>; + phy-names = "sata-phy"; + }; diff --git a/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt b/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt deleted file mode 100644 index 37824fac688e..000000000000 --- a/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt +++ /dev/null @@ -1,14 +0,0 @@ -* Samsung SATA PHY Controller - -SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers. -Each SATA PHY controller should have its own node. - -Required properties: -- compatible : compatible list, contains "samsung,exynos5-sata-phy" -- reg : <registers mapping> - -Example: - sata@ffe07000 { - compatible = "samsung,exynos5-sata-phy"; - reg = <0xffe07000 0x1000>; - }; diff --git a/Documentation/devicetree/bindings/ata/exynos-sata.txt b/Documentation/devicetree/bindings/ata/exynos-sata.txt index 0849f1025e34..cb48448247ea 100644 --- a/Documentation/devicetree/bindings/ata/exynos-sata.txt +++ b/Documentation/devicetree/bindings/ata/exynos-sata.txt @@ -4,14 +4,27 @@ SATA nodes are defined to describe on-chip Serial ATA controllers. Each SATA controller should have its own node. Required properties: -- compatible : compatible list, contains "samsung,exynos5-sata" -- interrupts : <interrupt mapping for SATA IRQ> -- reg : <registers mapping> -- samsung,sata-freq : <frequency in MHz> +- compatible : compatible list, contains "samsung,exynos5-sata" +- interrupts : <interrupt mapping for SATA IRQ> +- reg : <registers mapping> +- samsung,sata-freq : <frequency in MHz> +- phys : Must contain exactly one entry as specified + in phy-bindings.txt +- phy-names : Must be "sata-phy" + +Optional properties: +- clocks : Must contain an entry for each entry in clock-names. +- clock-names : Shall be "sata" for the external SATA bus clock, + and "sclk_sata" for the internal controller clock. Example: - sata@ffe08000 { - compatible = "samsung,exynos5-sata"; - reg = <0xffe08000 0x1000>; - interrupts = <115>; - }; + sata@122f0000 { + compatible = "snps,dwc-ahci"; + samsung,sata-freq = <66>; + reg = <0x122f0000 0x1ff>; + interrupts = <0 115 0>; + clocks = <&clock 277>, <&clock 143>; + clock-names = "sata", "sclk_sata"; + phys = <&sata_phy>; + phy-names = "sata-phy"; + }; diff --git a/Documentation/devicetree/bindings/ata/imx-sata.txt b/Documentation/devicetree/bindings/ata/imx-sata.txt new file mode 100644 index 000000000000..fa511db18408 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/imx-sata.txt @@ -0,0 +1,36 @@ +* Freescale i.MX AHCI SATA Controller + +The Freescale i.MX SATA controller mostly conforms to the AHCI interface +with some special extensions at integration level. + +Required properties: +- compatible : should be one of the following: + - "fsl,imx53-ahci" for i.MX53 SATA controller + - "fsl,imx6q-ahci" for i.MX6Q SATA controller +- interrupts : interrupt mapping for SATA IRQ +- reg : registers mapping +- clocks : list of clock specifiers, must contain an entry for each + required entry in clock-names +- clock-names : should include "sata", "sata_ref" and "ahb" entries + +Optional properties: +- fsl,transmit-level-mV : transmit voltage level, in millivolts. +- fsl,transmit-boost-mdB : transmit boost level, in milli-decibels +- fsl,transmit-atten-16ths : transmit attenuation, in 16ths +- fsl,receive-eq-mdB : receive equalisation, in milli-decibels + Please refer to the technical documentation or the driver source code + for the list of legal values for these options. +- fsl,no-spread-spectrum : disable spread-spectrum clocking on the SATA + link. + +Examples: + +sata@02200000 { + compatible = "fsl,imx6q-ahci"; + reg = <0x02200000 0x4000>; + interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6QDL_CLK_SATA>, + <&clks IMX6QDL_CLK_SATA_REF_100M>, + <&clks IMX6QDL_CLK_AHB>; + clock-names = "sata", "sata_ref", "ahb"; +}; diff --git a/Documentation/devicetree/bindings/ata/qcom-sata.txt b/Documentation/devicetree/bindings/ata/qcom-sata.txt new file mode 100644 index 000000000000..094de91cd9fd --- /dev/null +++ b/Documentation/devicetree/bindings/ata/qcom-sata.txt @@ -0,0 +1,48 @@ +* Qualcomm AHCI SATA Controller + +SATA nodes are defined to describe on-chip Serial ATA controllers. +Each SATA controller should have its own node. + +Required properties: +- compatible : compatible list, must contain "generic-ahci" +- interrupts : <interrupt mapping for SATA IRQ> +- reg : <registers mapping> +- phys : Must contain exactly one entry as specified + in phy-bindings.txt +- phy-names : Must be "sata-phy" + +Required properties for "qcom,ipq806x-ahci" compatible: +- clocks : Must contain an entry for each entry in clock-names. +- clock-names : Shall be: + "slave_iface" - Fabric port AHB clock for SATA + "iface" - AHB clock + "core" - core clock + "rxoob" - RX out-of-band clock + "pmalive" - Power Module Alive clock +- assigned-clocks : Shall be: + SATA_RXOOB_CLK + SATA_PMALIVE_CLK +- assigned-clock-rates : Shall be: + 100Mhz (100000000) for SATA_RXOOB_CLK + 100Mhz (100000000) for SATA_PMALIVE_CLK + +Example: + sata@29000000 { + compatible = "qcom,ipq806x-ahci", "generic-ahci"; + reg = <0x29000000 0x180>; + + interrupts = <0 209 0x0>; + + clocks = <&gcc SFAB_SATA_S_H_CLK>, + <&gcc SATA_H_CLK>, + <&gcc SATA_A_CLK>, + <&gcc SATA_RXOOB_CLK>, + <&gcc SATA_PMALIVE_CLK>; + clock-names = "slave_iface", "iface", "core", + "rxoob", "pmalive"; + assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>; + assigned-clock-rates = <100000000>, <100000000>; + + phys = <&sata_phy>; + phy-names = "sata-phy"; + }; diff --git a/Documentation/devicetree/bindings/ata/sata_rcar.txt b/Documentation/devicetree/bindings/ata/sata_rcar.txt index 1e6111333fa8..80ae87a0784b 100644 --- a/Documentation/devicetree/bindings/ata/sata_rcar.txt +++ b/Documentation/devicetree/bindings/ata/sata_rcar.txt @@ -3,8 +3,10 @@ Required properties: - compatible : should contain one of the following: - "renesas,sata-r8a7779" for R-Car H1 - - "renesas,sata-r8a7790" for R-Car H2 - - "renesas,sata-r8a7791" for R-Car M2 + - "renesas,sata-r8a7790-es1" for R-Car H2 ES1 + - "renesas,sata-r8a7790" for R-Car H2 other than ES1 + - "renesas,sata-r8a7791" for R-Car M2-W + - "renesas,sata-r8a7793" for R-Car M2-N - reg : address and length of the SATA registers; - interrupts : must consist of one interrupt specifier. diff --git a/Documentation/devicetree/bindings/ata/tegra-sata.txt b/Documentation/devicetree/bindings/ata/tegra-sata.txt new file mode 100644 index 000000000000..946f2072570b --- /dev/null +++ b/Documentation/devicetree/bindings/ata/tegra-sata.txt @@ -0,0 +1,30 @@ +Tegra124 SoC SATA AHCI controller + +Required properties : +- compatible : "nvidia,tegra124-ahci". +- reg : Should contain 2 entries: + - AHCI register set (SATA BAR5) + - SATA register set +- interrupts : Defines the interrupt used by SATA +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names : Must include the following entries: + - sata + - sata-oob + - cml1 + - pll_e +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + - sata + - sata-oob + - sata-cold +- phys : Must contain an entry for each entry in phy-names. + See ../phy/phy-bindings.txt for details. +- phy-names : Must include the following entries: + - sata-phy : XUSB PADCTL SATA PHY +- hvdd-supply : Defines the SATA HVDD regulator +- vddio-supply : Defines the SATA VDDIO regulator +- avdd-supply : Defines the SATA AVDD regulator +- target-5v-supply : Defines the SATA 5V power regulator +- target-12v-supply : Defines the SATA 12V power regulator diff --git a/Documentation/devicetree/bindings/bus/bcma.txt b/Documentation/devicetree/bindings/bus/bcma.txt new file mode 100644 index 000000000000..62a48348ac15 --- /dev/null +++ b/Documentation/devicetree/bindings/bus/bcma.txt @@ -0,0 +1,32 @@ +Driver for ARM AXI Bus with Broadcom Plugins (bcma) + +Required properties: + +- compatible : brcm,bus-axi + +- reg : iomem address range of chipcommon core + +The cores on the AXI bus are automatically detected by bcma with the +memory ranges they are using and they get registered afterwards. + +The top-level axi bus may contain children representing attached cores +(devices). This is needed since some hardware details can't be auto +detected (e.g. IRQ numbers). Also some of the cores may be responsible +for extra things, e.g. ChipCommon providing access to the GPIO chip. + +Example: + + axi@18000000 { + compatible = "brcm,bus-axi"; + reg = <0x18000000 0x1000>; + ranges = <0x00000000 0x18000000 0x00100000>; + #address-cells = <1>; + #size-cells = <1>; + + chipcommon { + reg = <0x00000000 0x1000>; + + gpio-controller; + #gpio-cells = <2>; + }; + }; diff --git a/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt b/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt new file mode 100644 index 000000000000..1eceefb20f01 --- /dev/null +++ b/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt @@ -0,0 +1,34 @@ +Broadcom GISB bus Arbiter controller + +Required properties: + +- compatible: + "brcm,gisb-arb" or "brcm,bcm7445-gisb-arb" for 28nm chips + "brcm,bcm7435-gisb-arb" for newer 40nm chips + "brcm,bcm7400-gisb-arb" for older 40nm chips and all 65nm chips + "brcm,bcm7038-gisb-arb" for 130nm chips +- reg: specifies the base physical address and size of the registers +- interrupt-parent: specifies the phandle to the parent interrupt controller + this arbiter gets interrupt line from +- interrupts: specifies the two interrupts (timeout and TEA) to be used from + the parent interrupt controller + +Optional properties: + +- brcm,gisb-arb-master-mask: 32-bits wide bitmask used to specify which GISB + masters are valid at the system level +- brcm,gisb-arb-master-names: string list of the litteral name of the GISB + masters. Should match the number of bits set in brcm,gisb-master-mask and + the order in which they appear + +Example: + +gisb-arb@f0400000 { + compatible = "brcm,gisb-arb"; + reg = <0xf0400000 0x800>; + interrupts = <0>, <2>; + interrupt-parent = <&sun_l2_intc>; + + brcm,gisb-arb-master-mask = <0x7>; + brcm,gisb-arb-master-names = "bsp_0", "scpu_0", "cpu_0"; +}; diff --git a/Documentation/devicetree/bindings/bus/imx-weim.txt b/Documentation/devicetree/bindings/bus/imx-weim.txt index 0fd76c405208..6630d842c7a3 100644 --- a/Documentation/devicetree/bindings/bus/imx-weim.txt +++ b/Documentation/devicetree/bindings/bus/imx-weim.txt @@ -8,7 +8,12 @@ The actual devices are instantiated from the child nodes of a WEIM node. Required properties: - - compatible: Should be set to "fsl,<soc>-weim" + - compatible: Should contain one of the following: + "fsl,imx1-weim" + "fsl,imx27-weim" + "fsl,imx51-weim" + "fsl,imx50-weim" + "fsl,imx6q-weim" - reg: A resource specifier for the register space (see the example below) - clocks: the clock, see the example below. @@ -19,6 +24,26 @@ Required properties: <cs-number> 0 <physical address of mapping> <size> +Optional properties: + + - fsl,weim-cs-gpr: For "fsl,imx50-weim" and "fsl,imx6q-weim" type of + devices, it should be the phandle to the system General + Purpose Register controller that contains WEIM CS GPR + register, e.g. IOMUXC_GPR1 on i.MX6Q. IOMUXC_GPR1[11:0] + should be set up as one of the following 4 possible + values depending on the CS space configuration. + + IOMUXC_GPR1[11:0] CS0 CS1 CS2 CS3 + --------------------------------------------- + 05 128M 0M 0M 0M + 033 64M 64M 0M 0M + 0113 64M 32M 32M 0M + 01111 32M 32M 32M 32M + + In case that the property is absent, the reset value or + what bootloader sets up in IOMUXC_GPR1[11:0] will be + used. + Timing property for child nodes. It is mandatory, not optional. - fsl,weim-cs-timing: The timing array, contains timing values for the @@ -43,6 +68,7 @@ Example for an imx6q-sabreauto board, the NOR flash connected to the WEIM: #address-cells = <2>; #size-cells = <1>; ranges = <0 0 0x08000000 0x08000000>; + fsl,weim-cs-gpr = <&gpr>; nor@0,0 { compatible = "cfi-flash"; diff --git a/Documentation/devicetree/bindings/bus/mvebu-mbus.txt b/Documentation/devicetree/bindings/bus/mvebu-mbus.txt index 7586fb68c072..5e16c3ccb061 100644 --- a/Documentation/devicetree/bindings/bus/mvebu-mbus.txt +++ b/Documentation/devicetree/bindings/bus/mvebu-mbus.txt @@ -48,9 +48,12 @@ Required properties: - compatible: Should be set to "marvell,mbus-controller". - reg: Device's register space. - Two entries are expected (see the examples below): - the first one controls the devices decoding window and - the second one controls the SDRAM decoding window. + Two or three entries are expected (see the examples below): + the first one controls the devices decoding window, + the second one controls the SDRAM decoding window and + the third controls the MBus bridge (only with the + marvell,armada370-mbus and marvell,armadaxp-mbus + compatible strings) Example: @@ -67,7 +70,7 @@ Example: mbusc: mbus-controller@20000 { compatible = "marvell,mbus-controller"; - reg = <0x20000 0x100>, <0x20180 0x20>; + reg = <0x20000 0x100>, <0x20180 0x20>, <0x20250 0x8>; }; /* more children ...*/ @@ -126,7 +129,7 @@ are skipped. mbusc: mbus-controller@20000 { compatible = "marvell,mbus-controller"; - reg = <0x20000 0x100>, <0x20180 0x20>; + reg = <0x20000 0x100>, <0x20180 0x20>, <0x20250 0x8>; }; /* more children ...*/ @@ -170,7 +173,7 @@ Using this macro, the above example would be: mbusc: mbus-controller@20000 { compatible = "marvell,mbus-controller"; - reg = <0x20000 0x100>, <0x20180 0x20>; + reg = <0x20000 0x100>, <0x20180 0x20>, <0x20250 0x8>; }; /* other children */ @@ -197,7 +200,7 @@ to be set by the operating system and that are guaranteed to be free of overlaps with one another or with the system memory ranges. Each entry in the property refers to exactly one window. If the operating system -choses to use a different set of mbus windows, it must ensure that any address +chooses to use a different set of mbus windows, it must ensure that any address translations performed from downstream devices are adapted accordingly. The operating system may insert additional mbus windows that do not conflict @@ -266,7 +269,7 @@ See the example below, where a more complete device tree is shown: ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>; mbusc: mbus-controller@20000 { - reg = <0x20000 0x100>, <0x20180 0x20>; + reg = <0x20000 0x100>, <0x20180 0x20>, <0x20250 0x8>; }; interrupt-controller@20000 { diff --git a/Documentation/devicetree/bindings/clock/altr_socfpga.txt b/Documentation/devicetree/bindings/clock/altr_socfpga.txt index 0045433eae1f..f72e80e0dade 100644 --- a/Documentation/devicetree/bindings/clock/altr_socfpga.txt +++ b/Documentation/devicetree/bindings/clock/altr_socfpga.txt @@ -21,5 +21,10 @@ Optional properties: - fixed-divider : If clocks have a fixed divider value, use this property. - clk-gate : For "socfpga-gate-clk", clk-gate contains the gating register and the bit index. -- div-reg : For "socfpga-gate-clk", div-reg contains the divider register, bit shift, - and width. +- div-reg : For "socfpga-gate-clk" and "socfpga-periph-clock", div-reg contains + the divider register, bit shift, and width. +- clk-phase : For the sdmmc_clk, contains the value of the clock phase that controls + the SDMMC CIU clock. The first value is the clk_sample(smpsel), and the second + value is the cclk_in_drv(drvsel). The clk-phase is used to enable the correct + hold/delay times that is needed for the SD/MMC CIU clock. The values of both + can be 0-315 degrees, in 45 degree increments. diff --git a/Documentation/devicetree/bindings/clock/arm-integrator.txt b/Documentation/devicetree/bindings/clock/arm-integrator.txt new file mode 100644 index 000000000000..11f5f95f571b --- /dev/null +++ b/Documentation/devicetree/bindings/clock/arm-integrator.txt @@ -0,0 +1,34 @@ +Clock bindings for ARM Integrator and Versatile Core Module clocks + +Auxiliary Oscillator Clock + +This is a configurable clock fed from a 24 MHz chrystal, +used for generating e.g. video clocks. It is located on the +core module and there is only one of these. + +This clock node *must* be a subnode of the core module, since +it obtains the base address for it's address range from its +parent node. + + +Required properties: +- compatible: must be "arm,integrator-cm-auxosc" or "arm,versatile-cm-auxosc" +- #clock-cells: must be <0> + +Optional properties: +- clocks: parent clock(s) + +Example: + +core-module@10000000 { + xtal24mhz: xtal24mhz@24M { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24000000>; + }; + auxosc: cm_aux_osc@25M { + #clock-cells = <0>; + compatible = "arm,integrator-cm-auxosc"; + clocks = <&xtal24mhz>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt index cd5e23912888..7a4d4926f44e 100644 --- a/Documentation/devicetree/bindings/clock/at91-clock.txt +++ b/Documentation/devicetree/bindings/clock/at91-clock.txt @@ -6,6 +6,16 @@ This binding uses the common clock binding[1]. Required properties: - compatible : shall be one of the following: + "atmel,at91sam9x5-sckc": + at91 SCKC (Slow Clock Controller) + This node contains the slow clock definitions. + + "atmel,at91sam9x5-clk-slow-osc": + at91 slow oscillator + + "atmel,at91sam9x5-clk-slow-rc-osc": + at91 internal slow RC oscillator + "atmel,at91rm9200-pmc" or "atmel,at91sam9g45-pmc" or "atmel,at91sam9n12-pmc" or @@ -15,8 +25,18 @@ Required properties: All at91 specific clocks (clocks defined below) must be child node of the PMC node. + "atmel,at91sam9x5-clk-slow" (under sckc node) + or + "atmel,at91sam9260-clk-slow" (under pmc node): + at91 slow clk + + "atmel,at91rm9200-clk-main-osc" + "atmel,at91sam9x5-clk-main-rc-osc" + at91 main clk sources + + "atmel,at91sam9x5-clk-main" "atmel,at91rm9200-clk-main": - at91 main oscillator + at91 main clock "atmel,at91rm9200-clk-master" or "atmel,at91sam9x5-clk-master": @@ -54,6 +74,66 @@ Required properties: "atmel,at91sam9x5-clk-utmi": at91 utmi clock + "atmel,sama5d4-clk-h32mx": + at91 h32mx clock + +Required properties for SCKC node: +- reg : defines the IO memory reserved for the SCKC. +- #size-cells : shall be 0 (reg is used to encode clk id). +- #address-cells : shall be 1 (reg is used to encode clk id). + + +For example: + sckc: sckc@fffffe50 { + compatible = "atmel,sama5d3-pmc"; + reg = <0xfffffe50 0x4> + #size-cells = <0>; + #address-cells = <1>; + + /* put at91 slow clocks here */ + }; + + +Required properties for internal slow RC oscillator: +- #clock-cells : from common clock binding; shall be set to 0. +- clock-frequency : define the internal RC oscillator frequency. + +Optional properties: +- clock-accuracy : define the internal RC oscillator accuracy. + +For example: + slow_rc_osc: slow_rc_osc { + compatible = "atmel,at91sam9x5-clk-slow-rc-osc"; + clock-frequency = <32768>; + clock-accuracy = <50000000>; + }; + +Required properties for slow oscillator: +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall encode the main osc source clk sources (see atmel datasheet). + +Optional properties: +- atmel,osc-bypass : boolean property. Set this when a clock signal is directly + provided on XIN. + +For example: + slow_osc: slow_osc { + compatible = "atmel,at91rm9200-clk-slow-osc"; + #clock-cells = <0>; + clocks = <&slow_xtal>; + }; + +Required properties for slow clock: +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall encode the slow clk sources (see atmel datasheet). + +For example: + clk32k: slck { + compatible = "atmel,at91sam9x5-clk-slow"; + #clock-cells = <0>; + clocks = <&slow_rc_osc &slow_osc>; + }; + Required properties for PMC node: - reg : defines the IO memory reserved for the PMC. - #size-cells : shall be 0 (reg is used to encode clk id). @@ -62,7 +142,7 @@ Required properties for PMC node: - interrupt-controller : tell that the PMC is an interrupt controller. - #interrupt-cells : must be set to 1. The first cell encodes the interrupt id, and reflect the bit position in the PMC_ER/DR/SR registers. - You can use the dt macros defined in dt-bindings/clk/at91.h. + You can use the dt macros defined in dt-bindings/clock/at91.h. 0 (AT91_PMC_MOSCS) -> main oscillator ready 1 (AT91_PMC_LOCKA) -> PLL A ready 2 (AT91_PMC_LOCKB) -> PLL B ready @@ -85,24 +165,57 @@ For example: /* put at91 clocks here */ }; +Required properties for main clock internal RC oscillator: +- interrupt-parent : must reference the PMC node. +- interrupts : shall be set to "<0>". +- clock-frequency : define the internal RC oscillator frequency. + +Optional properties: +- clock-accuracy : define the internal RC oscillator accuracy. + +For example: + main_rc_osc: main_rc_osc { + compatible = "atmel,at91sam9x5-clk-main-rc-osc"; + interrupt-parent = <&pmc>; + interrupts = <0>; + clock-frequency = <12000000>; + clock-accuracy = <50000000>; + }; + +Required properties for main clock oscillator: +- interrupt-parent : must reference the PMC node. +- interrupts : shall be set to "<0>". +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall encode the main osc source clk sources (see atmel datasheet). + +Optional properties: +- atmel,osc-bypass : boolean property. Specified if a clock signal is provided + on XIN. + + clock signal is directly provided on XIN pin. + +For example: + main_osc: main_osc { + compatible = "atmel,at91rm9200-clk-main-osc"; + interrupt-parent = <&pmc>; + interrupts = <0>; + #clock-cells = <0>; + clocks = <&main_xtal>; + }; + Required properties for main clock: - interrupt-parent : must reference the PMC node. - interrupts : shall be set to "<0>". - #clock-cells : from common clock binding; shall be set to 0. -- clocks (optional if clock-frequency is provided) : shall be the slow clock - phandle. This clock is used to calculate the main clock rate if - "clock-frequency" is not provided. -- clock-frequency : the main oscillator frequency.Prefer the use of - "clock-frequency" over automatic clock rate calculation. +- clocks : shall encode the main clk sources (see atmel datasheet). For example: main: mainck { - compatible = "atmel,at91rm9200-clk-main"; + compatible = "atmel,at91sam9x5-clk-main"; interrupt-parent = <&pmc>; interrupts = <0>; #clock-cells = <0>; - clocks = <&ck32k>; - clock-frequency = <18432000>; + clocks = <&main_rc_osc &main_osc>; }; Required properties for master clock: @@ -337,3 +450,14 @@ For example: #clock-cells = <0>; clocks = <&main>; }; + +Required properties for 32 bits bus Matrix clock (h32mx clock): +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall be the master clock source phandle. + +For example: + h32ck: h32mxck { + #clock-cells = <0>; + compatible = "atmel,sama5d4-clk-h32mx"; + clocks = <&mck>; + }; diff --git a/Documentation/devicetree/bindings/clock/axi-clkgen.txt b/Documentation/devicetree/bindings/clock/axi-clkgen.txt index 028b493e97ff..20e1704e7df2 100644 --- a/Documentation/devicetree/bindings/clock/axi-clkgen.txt +++ b/Documentation/devicetree/bindings/clock/axi-clkgen.txt @@ -5,7 +5,7 @@ This binding uses the common clock binding[1]. [1] Documentation/devicetree/bindings/clock/clock-bindings.txt Required properties: -- compatible : shall be "adi,axi-clkgen". +- compatible : shall be "adi,axi-clkgen-1.00.a" or "adi,axi-clkgen-2.00.a". - #clock-cells : from common clock binding; Should always be set to 0. - reg : Address and length of the axi-clkgen register set. - clocks : Phandle and clock specifier for the parent clock. diff --git a/Documentation/devicetree/bindings/clock/bcm-cygnus-clock.txt b/Documentation/devicetree/bindings/clock/bcm-cygnus-clock.txt new file mode 100644 index 000000000000..00d26edec8bc --- /dev/null +++ b/Documentation/devicetree/bindings/clock/bcm-cygnus-clock.txt @@ -0,0 +1,34 @@ +Broadcom Cygnus Clocks + +This binding uses the common clock binding: +Documentation/devicetree/bindings/clock/clock-bindings.txt + +Currently various "fixed" clocks are declared for peripheral drivers that use +the common clock framework to reference their core clocks. Proper support of +these clocks will be added later + +Device tree example: + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + osc: oscillator { + compatible = "fixed-clock"; + #clock-cells = <1>; + clock-frequency = <25000000>; + }; + + apb_clk: apb_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <1000000000>; + }; + + periph_clk: periph_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <500000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/bcm-kona-clock.txt b/Documentation/devicetree/bindings/clock/bcm-kona-clock.txt index 56d1f4961075..5286e260fcae 100644 --- a/Documentation/devicetree/bindings/clock/bcm-kona-clock.txt +++ b/Documentation/devicetree/bindings/clock/bcm-kona-clock.txt @@ -10,12 +10,12 @@ This binding uses the common clock binding: Required properties: - compatible - Shall have one of the following values: - - "brcm,bcm11351-root-ccu" - - "brcm,bcm11351-aon-ccu" - - "brcm,bcm11351-hub-ccu" - - "brcm,bcm11351-master-ccu" - - "brcm,bcm11351-slave-ccu" + Shall have a value of the form "brcm,<model>-<which>-ccu", + where <model> is a Broadcom SoC model number and <which> is + the name of a defined CCU. For example: + "brcm,bcm11351-root-ccu" + The compatible strings used for each supported SoC family + are defined below. - reg Shall define the base and range of the address space containing clock control registers @@ -26,12 +26,48 @@ Required properties: Shall be an ordered list of strings defining the names of the clocks provided by the CCU. +Device tree example: + + slave_ccu: slave_ccu { + compatible = "brcm,bcm11351-slave-ccu"; + reg = <0x3e011000 0x0f00>; + #clock-cells = <1>; + clock-output-names = "uartb", + "uartb2", + "uartb3", + "uartb4"; + }; + + ref_crystal_clk: ref_crystal { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <26000000>; + }; + + uart@3e002000 { + compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart"; + status = "disabled"; + reg = <0x3e002000 0x1000>; + clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB3>; + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + }; + +BCM281XX family +--------------- +CCU compatible string values for SoCs in the BCM281XX family are: + "brcm,bcm11351-root-ccu" + "brcm,bcm11351-aon-ccu" + "brcm,bcm11351-hub-ccu" + "brcm,bcm11351-master-ccu" + "brcm,bcm11351-slave-ccu" -BCM281XX family SoCs use Kona CCUs. The following table defines -the set of CCUs and clock specifiers for BCM281XX clocks. When -a clock consumer references a clocks, its symbolic specifier -(rather than its numeric index value) should be used. These -specifiers are defined in "include/dt-bindings/clock/bcm281xx.h". +The following table defines the set of CCUs and clock specifiers for +BCM281XX family clocks. When a clock consumer references a clocks, +its symbolic specifier (rather than its numeric index value) should +be used. These specifiers are defined in: + "include/dt-bindings/clock/bcm281xx.h" CCU Clock Type Index Specifier --- ----- ---- ----- --------- @@ -64,30 +100,40 @@ specifiers are defined in "include/dt-bindings/clock/bcm281xx.h". slave pwm peri 9 BCM281XX_SLAVE_CCU_PWM -Device tree example: +BCM21664 family +--------------- +CCU compatible string values for SoCs in the BCM21664 family are: + "brcm,bcm21664-root-ccu" + "brcm,bcm21664-aon-ccu" + "brcm,bcm21664-master-ccu" + "brcm,bcm21664-slave-ccu" - slave_ccu: slave_ccu { - compatible = "brcm,bcm11351-slave-ccu"; - reg = <0x3e011000 0x0f00>; - #clock-cells = <1>; - clock-output-names = "uartb", - "uartb2", - "uartb3", - "uartb4"; - }; +The following table defines the set of CCUs and clock specifiers for +BCM21664 family clocks. When a clock consumer references a clocks, +its symbolic specifier (rather than its numeric index value) should +be used. These specifiers are defined in: + "include/dt-bindings/clock/bcm21664.h" - ref_crystal_clk: ref_crystal { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <26000000>; - }; + CCU Clock Type Index Specifier + --- ----- ---- ----- --------- + root frac_1m peri 0 BCM21664_ROOT_CCU_FRAC_1M - uart@3e002000 { - compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart"; - status = "disabled"; - reg = <0x3e002000 0x1000>; - clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB3>; - interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; - reg-shift = <2>; - reg-io-width = <4>; - }; + aon hub_timer peri 0 BCM21664_AON_CCU_HUB_TIMER + + master sdio1 peri 0 BCM21664_MASTER_CCU_SDIO1 + master sdio2 peri 1 BCM21664_MASTER_CCU_SDIO2 + master sdio3 peri 2 BCM21664_MASTER_CCU_SDIO3 + master sdio4 peri 3 BCM21664_MASTER_CCU_SDIO4 + master sdio1_sleep peri 4 BCM21664_MASTER_CCU_SDIO1_SLEEP + master sdio2_sleep peri 5 BCM21664_MASTER_CCU_SDIO2_SLEEP + master sdio3_sleep peri 6 BCM21664_MASTER_CCU_SDIO3_SLEEP + master sdio4_sleep peri 7 BCM21664_MASTER_CCU_SDIO4_SLEEP + + slave uartb peri 0 BCM21664_SLAVE_CCU_UARTB + slave uartb2 peri 1 BCM21664_SLAVE_CCU_UARTB2 + slave uartb3 peri 2 BCM21664_SLAVE_CCU_UARTB3 + slave uartb4 peri 3 BCM21664_SLAVE_CCU_UARTB4 + slave bsc1 peri 4 BCM21664_SLAVE_CCU_BSC1 + slave bsc2 peri 5 BCM21664_SLAVE_CCU_BSC2 + slave bsc3 peri 6 BCM21664_SLAVE_CCU_BSC3 + slave bsc4 peri 7 BCM21664_SLAVE_CCU_BSC4 diff --git a/Documentation/devicetree/bindings/clock/clk-palmas-clk32kg-clocks.txt b/Documentation/devicetree/bindings/clock/clk-palmas-clk32kg-clocks.txt new file mode 100644 index 000000000000..4208886d834a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/clk-palmas-clk32kg-clocks.txt @@ -0,0 +1,35 @@ +* Palmas 32KHz clocks * + +Palmas device has two clock output pins for 32KHz, KG and KG_AUDIO. + +This binding uses the common clock binding ./clock-bindings.txt. + +Required properties: +- compatible : "ti,palmas-clk32kg" for clk32kg clock + "ti,palmas-clk32kgaudio" for clk32kgaudio clock +- #clock-cells : shall be set to 0. + +Optional property: +- ti,external-sleep-control: The external enable input pins controlled the + enable/disable of clocks. The external enable input pins ENABLE1, + ENABLE2 and NSLEEP. The valid values for the external pins are: + PALMAS_EXT_CONTROL_PIN_ENABLE1 for ENABLE1 pin + PALMAS_EXT_CONTROL_PIN_ENABLE2 for ENABLE2 pin + PALMAS_EXT_CONTROL_PIN_NSLEEP for NSLEEP pin + Option 0 or missing this property means the clock is enabled/disabled + via register access and these pins do not have any control. + The macros of external control pins for DTS is defined at + dt-bindings/mfd/palmas.h + +Example: + #include <dt-bindings/mfd/palmas.h> + ... + palmas: tps65913@58 { + ... + clk32kg: palmas_clk32k@0 { + compatible = "ti,palmas-clk32kg"; + #clock-cells = <0>; + ti,external-sleep-control = <PALMAS_EXT_CONTROL_PIN_NSLEEP>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/clock/clk-s5pv210-audss.txt b/Documentation/devicetree/bindings/clock/clk-s5pv210-audss.txt new file mode 100644 index 000000000000..4fc869b69d4a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/clk-s5pv210-audss.txt @@ -0,0 +1,53 @@ +* Samsung Audio Subsystem Clock Controller + +The Samsung Audio Subsystem clock controller generates and supplies clocks +to Audio Subsystem block available in the S5PV210 and compatible SoCs. + +Required Properties: + +- compatible: should be "samsung,s5pv210-audss-clock". +- reg: physical base address and length of the controller's register set. + +- #clock-cells: should be 1. + +- clocks: + - hclk: AHB bus clock of the Audio Subsystem. + - xxti: Optional fixed rate PLL reference clock, parent of mout_audss. If + not specified (i.e. xusbxti is used for PLL reference), it is fixed to + a clock named "xxti". + - fout_epll: Input PLL to the AudioSS block, parent of mout_audss. + - iiscdclk0: Optional external i2s clock, parent of mout_i2s. If not + specified, it is fixed to a clock named "iiscdclk0". + - sclk_audio0: Audio bus clock, parent of mout_i2s. + +- clock-names: Aliases for the above clocks. They should be "hclk", + "xxti", "fout_epll", "iiscdclk0", and "sclk_audio0" respectively. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/s5pv210-audss-clk.h header and can be used in device +tree sources. + +Example: Clock controller node. + + clk_audss: clock-controller@c0900000 { + compatible = "samsung,s5pv210-audss-clock"; + reg = <0xc0900000 0x1000>; + #clock-cells = <1>; + clock-names = "hclk", "xxti", + "fout_epll", "sclk_audio0"; + clocks = <&clocks DOUT_HCLKP>, <&xxti>, + <&clocks FOUT_EPLL>, <&clocks SCLK_AUDIO0>; + }; + +Example: I2S controller node that consumes the clock generated by the clock + controller. Refer to the standard clock bindings for information + about 'clocks' and 'clock-names' property. + + i2s0: i2s@03830000 { + /* ... */ + clock-names = "iis", "i2s_opclk0", + "i2s_opclk1"; + clocks = <&clk_audss CLK_I2S>, <&clk_audss CLK_I2S>, + <&clk_audss CLK_DOUT_AUD_BUS>; + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/clock/clock-bindings.txt b/Documentation/devicetree/bindings/clock/clock-bindings.txt index 7c52c29d99fa..06fc6d541c89 100644 --- a/Documentation/devicetree/bindings/clock/clock-bindings.txt +++ b/Documentation/devicetree/bindings/clock/clock-bindings.txt @@ -44,6 +44,22 @@ For example: clocks by index. The names should reflect the clock output signal names for the device. +clock-indices: If the identifying number for the clocks in the node + is not linear from zero, then this allows the mapping of + identifiers into the clock-output-names array. + +For example, if we have two clocks <&oscillator 1> and <&oscillator 3>: + + oscillator { + compatible = "myclocktype"; + #clock-cells = <1>; + clock-indices = <1>, <3>; + clock-output-names = "clka", "clkb"; + } + + This ensures we do not have any empty strings in clock-output-names + + ==Clock consumers== Required properties: @@ -115,3 +131,39 @@ clock signal, and a UART. ("pll" and "pll-switched"). * The UART has its baud clock connected the external oscillator and its register clock connected to the PLL clock (the "pll-switched" signal) + +==Assigned clock parents and rates== + +Some platforms may require initial configuration of default parent clocks +and clock frequencies. Such a configuration can be specified in a device tree +node through assigned-clocks, assigned-clock-parents and assigned-clock-rates +properties. The assigned-clock-parents property should contain a list of parent +clocks in form of phandle and clock specifier pairs, the assigned-clock-parents +property the list of assigned clock frequency values - corresponding to clocks +listed in the assigned-clocks property. + +To skip setting parent or rate of a clock its corresponding entry should be +set to 0, or can be omitted if it is not followed by any non-zero entry. + + uart@a000 { + compatible = "fsl,imx-uart"; + reg = <0xa000 0x1000>; + ... + clocks = <&osc 0>, <&pll 1>; + clock-names = "baud", "register"; + + assigned-clocks = <&clkcon 0>, <&pll 2>; + assigned-clock-parents = <&pll 2>; + assigned-clock-rates = <0>, <460800>; + }; + +In this example the <&pll 2> clock is set as parent of clock <&clkcon 0> and +the <&pll 2> clock is assigned a frequency value of 460800 Hz. + +Configuring a clock's parent and rate through the device node that consumes +the clock can be done only for clocks that have a single user. Specifying +conflicting parent or rate configuration in multiple consumer nodes for +a shared clock is forbidden. + +Configuration of common clocks, which affect multiple consumer devices can +be similarly specified in the clock provider node. diff --git a/Documentation/devicetree/bindings/clock/clps711x-clock.txt b/Documentation/devicetree/bindings/clock/clps711x-clock.txt new file mode 100644 index 000000000000..ce5a7476f05d --- /dev/null +++ b/Documentation/devicetree/bindings/clock/clps711x-clock.txt @@ -0,0 +1,19 @@ +* Clock bindings for the Cirrus Logic CLPS711X CPUs + +Required properties: +- compatible : Shall contain "cirrus,clps711x-clk". +- reg : Address of the internal register set. +- startup-frequency: Factory set CPU startup frequency in HZ. +- #clock-cells : Should be <1>. + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/clps711x-clock.h +for the full list of CLPS711X clock IDs. + +Example: + clks: clks@80000000 { + #clock-cells = <1>; + compatible = "cirrus,ep7312-clk", "cirrus,clps711x-clk"; + reg = <0x80000000 0xc000>; + startup-frequency = <73728000>; + }; diff --git a/Documentation/devicetree/bindings/clock/exynos3250-clock.txt b/Documentation/devicetree/bindings/clock/exynos3250-clock.txt new file mode 100644 index 000000000000..f57d9dd9ea85 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/exynos3250-clock.txt @@ -0,0 +1,49 @@ +* Samsung Exynos3250 Clock Controller + +The Exynos3250 clock controller generates and supplies clock to various +controllers within the Exynos3250 SoC. + +Required Properties: + +- compatible: should be one of the following. + - "samsung,exynos3250-cmu" - controller compatible with Exynos3250 SoC. + - "samsung,exynos3250-cmu-dmc" - controller compatible with + Exynos3250 SoC for Dynamic Memory Controller domain. + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos3250.h header and can be used in device +tree sources. + +Example 1: Examples of clock controller nodes are listed below. + + cmu: clock-controller@10030000 { + compatible = "samsung,exynos3250-cmu"; + reg = <0x10030000 0x20000>; + #clock-cells = <1>; + }; + + cmu_dmc: clock-controller@105C0000 { + compatible = "samsung,exynos3250-cmu-dmc"; + reg = <0x105C0000 0x2000>; + #clock-cells = <1>; + }; + +Example 2: UART controller node that consumes the clock generated by the clock + controller. Refer to the standard clock bindings for information + about 'clocks' and 'clock-names' property. + + serial@13800000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x13800000 0x100>; + interrupts = <0 109 0>; + clocks = <&cmu CLK_UART0>, <&cmu CLK_SCLK_UART0>; + clock-names = "uart", "clk_uart_baud0"; + }; diff --git a/Documentation/devicetree/bindings/clock/exynos4-clock.txt b/Documentation/devicetree/bindings/clock/exynos4-clock.txt index a2ac2d9ac71a..f5a5b19ed3b2 100644 --- a/Documentation/devicetree/bindings/clock/exynos4-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos4-clock.txt @@ -15,259 +15,12 @@ Required Properties: - #clock-cells: should be 1. -The following is the list of clocks generated by the controller. Each clock is -assigned an identifier and client nodes use this identifier to specify the -clock which they consume. Some of the clocks are available only on a particular -Exynos4 SoC and this is specified where applicable. - - - [Core Clocks] - - Clock ID SoC (if specific) - ----------------------------------------------- - - xxti 1 - xusbxti 2 - fin_pll 3 - fout_apll 4 - fout_mpll 5 - fout_epll 6 - fout_vpll 7 - sclk_apll 8 - sclk_mpll 9 - sclk_epll 10 - sclk_vpll 11 - arm_clk 12 - aclk200 13 - aclk100 14 - aclk160 15 - aclk133 16 - mout_mpll_user_t 17 Exynos4x12 - mout_mpll_user_c 18 Exynos4x12 - mout_core 19 - mout_apll 20 - - - [Clock Gate for Special Clocks] - - Clock ID SoC (if specific) - ----------------------------------------------- - - sclk_fimc0 128 - sclk_fimc1 129 - sclk_fimc2 130 - sclk_fimc3 131 - sclk_cam0 132 - sclk_cam1 133 - sclk_csis0 134 - sclk_csis1 135 - sclk_hdmi 136 - sclk_mixer 137 - sclk_dac 138 - sclk_pixel 139 - sclk_fimd0 140 - sclk_mdnie0 141 Exynos4412 - sclk_mdnie_pwm0 12 142 Exynos4412 - sclk_mipi0 143 - sclk_audio0 144 - sclk_mmc0 145 - sclk_mmc1 146 - sclk_mmc2 147 - sclk_mmc3 148 - sclk_mmc4 149 - sclk_sata 150 Exynos4210 - sclk_uart0 151 - sclk_uart1 152 - sclk_uart2 153 - sclk_uart3 154 - sclk_uart4 155 - sclk_audio1 156 - sclk_audio2 157 - sclk_spdif 158 - sclk_spi0 159 - sclk_spi1 160 - sclk_spi2 161 - sclk_slimbus 162 - sclk_fimd1 163 Exynos4210 - sclk_mipi1 164 Exynos4210 - sclk_pcm1 165 - sclk_pcm2 166 - sclk_i2s1 167 - sclk_i2s2 168 - sclk_mipihsi 169 Exynos4412 - sclk_mfc 170 - sclk_pcm0 171 - sclk_g3d 172 - sclk_pwm_isp 173 Exynos4x12 - sclk_spi0_isp 174 Exynos4x12 - sclk_spi1_isp 175 Exynos4x12 - sclk_uart_isp 176 Exynos4x12 - sclk_fimg2d 177 - - [Peripheral Clock Gates] - - Clock ID SoC (if specific) - ----------------------------------------------- - - fimc0 256 - fimc1 257 - fimc2 258 - fimc3 259 - csis0 260 - csis1 261 - jpeg 262 - smmu_fimc0 263 - smmu_fimc1 264 - smmu_fimc2 265 - smmu_fimc3 266 - smmu_jpeg 267 - vp 268 - mixer 269 - tvenc 270 Exynos4210 - hdmi 271 - smmu_tv 272 - mfc 273 - smmu_mfcl 274 - smmu_mfcr 275 - g3d 276 - g2d 277 - rotator 278 Exynos4210 - mdma 279 Exynos4210 - smmu_g2d 280 Exynos4210 - smmu_rotator 281 Exynos4210 - smmu_mdma 282 Exynos4210 - fimd0 283 - mie0 284 - mdnie0 285 Exynos4412 - dsim0 286 - smmu_fimd0 287 - fimd1 288 Exynos4210 - mie1 289 Exynos4210 - dsim1 290 Exynos4210 - smmu_fimd1 291 Exynos4210 - pdma0 292 - pdma1 293 - pcie_phy 294 - sata_phy 295 Exynos4210 - tsi 296 - sdmmc0 297 - sdmmc1 298 - sdmmc2 299 - sdmmc3 300 - sdmmc4 301 - sata 302 Exynos4210 - sromc 303 - usb_host 304 - usb_device 305 - pcie 306 - onenand 307 - nfcon 308 - smmu_pcie 309 - gps 310 - smmu_gps 311 - uart0 312 - uart1 313 - uart2 314 - uart3 315 - uart4 316 - i2c0 317 - i2c1 318 - i2c2 319 - i2c3 320 - i2c4 321 - i2c5 322 - i2c6 323 - i2c7 324 - i2c_hdmi 325 - tsadc 326 - spi0 327 - spi1 328 - spi2 329 - i2s1 330 - i2s2 331 - pcm0 332 - i2s0 333 - pcm1 334 - pcm2 335 - pwm 336 - slimbus 337 - spdif 338 - ac97 339 - modemif 340 - chipid 341 - sysreg 342 - hdmi_cec 343 - mct 344 - wdt 345 - rtc 346 - keyif 347 - audss 348 - mipi_hsi 349 Exynos4210 - mdma2 350 Exynos4210 - pixelasyncm0 351 - pixelasyncm1 352 - fimc_lite0 353 Exynos4x12 - fimc_lite1 354 Exynos4x12 - ppmuispx 355 Exynos4x12 - ppmuispmx 356 Exynos4x12 - fimc_isp 357 Exynos4x12 - fimc_drc 358 Exynos4x12 - fimc_fd 359 Exynos4x12 - mcuisp 360 Exynos4x12 - gicisp 361 Exynos4x12 - smmu_isp 362 Exynos4x12 - smmu_drc 363 Exynos4x12 - smmu_fd 364 Exynos4x12 - smmu_lite0 365 Exynos4x12 - smmu_lite1 366 Exynos4x12 - mcuctl_isp 367 Exynos4x12 - mpwm_isp 368 Exynos4x12 - i2c0_isp 369 Exynos4x12 - i2c1_isp 370 Exynos4x12 - mtcadc_isp 371 Exynos4x12 - pwm_isp 372 Exynos4x12 - wdt_isp 373 Exynos4x12 - uart_isp 374 Exynos4x12 - asyncaxim 375 Exynos4x12 - smmu_ispcx 376 Exynos4x12 - spi0_isp 377 Exynos4x12 - spi1_isp 378 Exynos4x12 - pwm_isp_sclk 379 Exynos4x12 - spi0_isp_sclk 380 Exynos4x12 - spi1_isp_sclk 381 Exynos4x12 - uart_isp_sclk 382 Exynos4x12 - tmu_apbif 383 - - [Mux Clocks] - - Clock ID SoC (if specific) - ----------------------------------------------- - - mout_fimc0 384 - mout_fimc1 385 - mout_fimc2 386 - mout_fimc3 387 - mout_cam0 388 - mout_cam1 389 - mout_csis0 390 - mout_csis1 391 - mout_g3d0 392 - mout_g3d1 393 - mout_g3d 394 - aclk400_mcuisp 395 Exynos4x12 - - [Div Clocks] - - Clock ID SoC (if specific) - ----------------------------------------------- - - div_isp0 450 Exynos4x12 - div_isp1 451 Exynos4x12 - div_mcuisp0 452 Exynos4x12 - div_mcuisp1 453 Exynos4x12 - div_aclk200 454 Exynos4x12 - div_aclk400_mcuisp 455 Exynos4x12 +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos4.h header and can be used in device +tree sources. Example 1: An example of a clock controller node is listed below. @@ -285,6 +38,6 @@ Example 2: UART controller node that consumes the clock generated by the clock compatible = "samsung,exynos4210-uart"; reg = <0x13820000 0x100>; interrupts = <0 54 0>; - clocks = <&clock 314>, <&clock 153>; + clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>; clock-names = "uart", "clk_uart_baud0"; }; diff --git a/Documentation/devicetree/bindings/clock/exynos5250-clock.txt b/Documentation/devicetree/bindings/clock/exynos5250-clock.txt index 72ce617dea82..536eacd1063f 100644 --- a/Documentation/devicetree/bindings/clock/exynos5250-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5250-clock.txt @@ -13,163 +13,12 @@ Required Properties: - #clock-cells: should be 1. -The following is the list of clocks generated by the controller. Each clock is -assigned an identifier and client nodes use this identifier to specify the -clock which they consume. - - - [Core Clocks] - - Clock ID - ---------------------------- - - fin_pll 1 - - [Clock Gate for Special Clocks] - - Clock ID - ---------------------------- - - sclk_cam_bayer 128 - sclk_cam0 129 - sclk_cam1 130 - sclk_gscl_wa 131 - sclk_gscl_wb 132 - sclk_fimd1 133 - sclk_mipi1 134 - sclk_dp 135 - sclk_hdmi 136 - sclk_pixel 137 - sclk_audio0 138 - sclk_mmc0 139 - sclk_mmc1 140 - sclk_mmc2 141 - sclk_mmc3 142 - sclk_sata 143 - sclk_usb3 144 - sclk_jpeg 145 - sclk_uart0 146 - sclk_uart1 147 - sclk_uart2 148 - sclk_uart3 149 - sclk_pwm 150 - sclk_audio1 151 - sclk_audio2 152 - sclk_spdif 153 - sclk_spi0 154 - sclk_spi1 155 - sclk_spi2 156 - div_i2s1 157 - div_i2s2 158 - sclk_hdmiphy 159 - div_pcm0 160 - - - [Peripheral Clock Gates] - - Clock ID - ---------------------------- - - gscl0 256 - gscl1 257 - gscl2 258 - gscl3 259 - gscl_wa 260 - gscl_wb 261 - smmu_gscl0 262 - smmu_gscl1 263 - smmu_gscl2 264 - smmu_gscl3 265 - mfc 266 - smmu_mfcl 267 - smmu_mfcr 268 - rotator 269 - jpeg 270 - mdma1 271 - smmu_rotator 272 - smmu_jpeg 273 - smmu_mdma1 274 - pdma0 275 - pdma1 276 - sata 277 - usbotg 278 - mipi_hsi 279 - sdmmc0 280 - sdmmc1 281 - sdmmc2 282 - sdmmc3 283 - sromc 284 - usb2 285 - usb3 286 - sata_phyctrl 287 - sata_phyi2c 288 - uart0 289 - uart1 290 - uart2 291 - uart3 292 - uart4 293 - i2c0 294 - i2c1 295 - i2c2 296 - i2c3 297 - i2c4 298 - i2c5 299 - i2c6 300 - i2c7 301 - i2c_hdmi 302 - adc 303 - spi0 304 - spi1 305 - spi2 306 - i2s1 307 - i2s2 308 - pcm1 309 - pcm2 310 - pwm 311 - spdif 312 - ac97 313 - hsi2c0 314 - hsi2c1 315 - hs12c2 316 - hs12c3 317 - chipid 318 - sysreg 319 - pmu 320 - cmu_top 321 - cmu_core 322 - cmu_mem 323 - tzpc0 324 - tzpc1 325 - tzpc2 326 - tzpc3 327 - tzpc4 328 - tzpc5 329 - tzpc6 330 - tzpc7 331 - tzpc8 332 - tzpc9 333 - hdmi_cec 334 - mct 335 - wdt 336 - rtc 337 - tmu 338 - fimd1 339 - mie1 340 - dsim0 341 - dp 342 - mixer 343 - hdmi 344 - g2d 345 - mdma0 346 - smmu_mdma0 347 - - - [Clock Muxes] - - Clock ID - ---------------------------- - mout_hdmi 1024 +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos5250.h header and can be used in device +tree sources. Example 1: An example of a clock controller node is listed below. @@ -187,6 +36,6 @@ Example 2: UART controller node that consumes the clock generated by the clock compatible = "samsung,exynos4210-uart"; reg = <0x13820000 0x100>; interrupts = <0 54 0>; - clocks = <&clock 314>, <&clock 153>; + clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>; clock-names = "uart", "clk_uart_baud0"; }; diff --git a/Documentation/devicetree/bindings/clock/exynos5260-clock.txt b/Documentation/devicetree/bindings/clock/exynos5260-clock.txt new file mode 100644 index 000000000000..5496b2fac483 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/exynos5260-clock.txt @@ -0,0 +1,190 @@ +* Samsung Exynos5260 Clock Controller + +Exynos5260 has 13 clock controllers which are instantiated +independently from the device-tree. These clock controllers +generate and supply clocks to various hardware blocks within +the SoC. + +Each clock is assigned an identifier and client nodes can use +this identifier to specify the clock which they consume. All +available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos5260-clk.h header and can be used in +device tree sources. + +External clocks: + +There are several clocks that are generated outside the SoC. It +is expected that they are defined using standard clock bindings +with following clock-output-names: + + - "fin_pll" - PLL input clock from XXTI + - "xrtcxti" - input clock from XRTCXTI + - "ioclk_pcm_extclk" - pcm external operation clock + - "ioclk_spdif_extclk" - spdif external operation clock + - "ioclk_i2s_cdclk" - i2s0 codec clock + +Phy clocks: + +There are several clocks which are generated by specific PHYs. +These clocks are fed into the clock controller and then routed to +the hardware blocks. These clocks are defined as fixed clocks in the +driver with following names: + + - "phyclk_dptx_phy_ch3_txd_clk" - dp phy clock for channel 3 + - "phyclk_dptx_phy_ch2_txd_clk" - dp phy clock for channel 2 + - "phyclk_dptx_phy_ch1_txd_clk" - dp phy clock for channel 1 + - "phyclk_dptx_phy_ch0_txd_clk" - dp phy clock for channel 0 + - "phyclk_hdmi_phy_tmds_clko" - hdmi phy tmds clock + - "phyclk_hdmi_phy_pixel_clko" - hdmi phy pixel clock + - "phyclk_hdmi_link_o_tmds_clkhi" - hdmi phy for hdmi link + - "phyclk_dptx_phy_o_ref_clk_24m" - dp phy reference clock + - "phyclk_dptx_phy_clk_div2" + - "phyclk_mipi_dphy_4l_m_rxclkesc0" + - "phyclk_usbhost20_phy_phyclock" - usb 2.0 phy clock + - "phyclk_usbhost20_phy_freeclk" + - "phyclk_usbhost20_phy_clk48mohci" + - "phyclk_usbdrd30_udrd30_pipe_pclk" + - "phyclk_usbdrd30_udrd30_phyclock" - usb 3.0 phy clock + +Required Properties for Clock Controller: + + - compatible: should be one of the following. + 1) "samsung,exynos5260-clock-top" + 2) "samsung,exynos5260-clock-peri" + 3) "samsung,exynos5260-clock-egl" + 4) "samsung,exynos5260-clock-kfc" + 5) "samsung,exynos5260-clock-g2d" + 6) "samsung,exynos5260-clock-mif" + 7) "samsung,exynos5260-clock-mfc" + 8) "samsung,exynos5260-clock-g3d" + 9) "samsung,exynos5260-clock-fsys" + 10) "samsung,exynos5260-clock-aud" + 11) "samsung,exynos5260-clock-isp" + 12) "samsung,exynos5260-clock-gscl" + 13) "samsung,exynos5260-clock-disp" + + - reg: physical base address of the controller and the length of + memory mapped region. + + - #clock-cells: should be 1. + + - clocks: list of clock identifiers which are fed as the input to + the given clock controller. Please refer the next section to find + the input clocks for a given controller. + + - clock-names: list of names of clocks which are fed as the input + to the given clock controller. + +Input clocks for top clock controller: + - fin_pll + - dout_mem_pll + - dout_bus_pll + - dout_media_pll + +Input clocks for peri clock controller: + - fin_pll + - ioclk_pcm_extclk + - ioclk_i2s_cdclk + - ioclk_spdif_extclk + - phyclk_hdmi_phy_ref_cko + - dout_aclk_peri_66 + - dout_sclk_peri_uart0 + - dout_sclk_peri_uart1 + - dout_sclk_peri_uart2 + - dout_sclk_peri_spi0_b + - dout_sclk_peri_spi1_b + - dout_sclk_peri_spi2_b + - dout_aclk_peri_aud + - dout_sclk_peri_spi0_b + +Input clocks for egl clock controller: + - fin_pll + - dout_bus_pll + +Input clocks for kfc clock controller: + - fin_pll + - dout_media_pll + +Input clocks for g2d clock controller: + - fin_pll + - dout_aclk_g2d_333 + +Input clocks for mif clock controller: + - fin_pll + +Input clocks for mfc clock controller: + - fin_pll + - dout_aclk_mfc_333 + +Input clocks for g3d clock controller: + - fin_pll + +Input clocks for fsys clock controller: + - fin_pll + - phyclk_usbhost20_phy_phyclock + - phyclk_usbhost20_phy_freeclk + - phyclk_usbhost20_phy_clk48mohci + - phyclk_usbdrd30_udrd30_pipe_pclk + - phyclk_usbdrd30_udrd30_phyclock + - dout_aclk_fsys_200 + +Input clocks for aud clock controller: + - fin_pll + - fout_aud_pll + - ioclk_i2s_cdclk + - ioclk_pcm_extclk + +Input clocks for isp clock controller: + - fin_pll + - dout_aclk_isp1_266 + - dout_aclk_isp1_400 + - mout_aclk_isp1_266 + +Input clocks for gscl clock controller: + - fin_pll + - dout_aclk_gscl_400 + - dout_aclk_gscl_333 + +Input clocks for disp clock controller: + - fin_pll + - phyclk_dptx_phy_ch3_txd_clk + - phyclk_dptx_phy_ch2_txd_clk + - phyclk_dptx_phy_ch1_txd_clk + - phyclk_dptx_phy_ch0_txd_clk + - phyclk_hdmi_phy_tmds_clko + - phyclk_hdmi_phy_ref_clko + - phyclk_hdmi_phy_pixel_clko + - phyclk_hdmi_link_o_tmds_clkhi + - phyclk_mipi_dphy_4l_m_txbyte_clkhs + - phyclk_dptx_phy_o_ref_clk_24m + - phyclk_dptx_phy_clk_div2 + - phyclk_mipi_dphy_4l_m_rxclkesc0 + - phyclk_hdmi_phy_ref_cko + - ioclk_spdif_extclk + - dout_aclk_peri_aud + - dout_aclk_disp_222 + - dout_sclk_disp_pixel + - dout_aclk_disp_333 + +Example 1: An example of a clock controller node is listed below. + + clock_mfc: clock-controller@11090000 { + compatible = "samsung,exynos5260-clock-mfc"; + clock = <&fin_pll>, <&clock_top TOP_DOUT_ACLK_MFC_333>; + clock-names = "fin_pll", "dout_aclk_mfc_333"; + reg = <0x11090000 0x10000>; + #clock-cells = <1>; + }; + +Example 2: UART controller node that consumes the clock generated by the + peri clock controller. Refer to the standard clock bindings for + information about 'clocks' and 'clock-names' property. + + serial@12C00000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C00000 0x100>; + interrupts = <0 146 0>; + clocks = <&clock_peri PERI_PCLK_UART0>, <&clock_peri PERI_SCLK_UART0>; + clock-names = "uart", "clk_uart_baud0"; + }; + diff --git a/Documentation/devicetree/bindings/clock/exynos5410-clock.txt b/Documentation/devicetree/bindings/clock/exynos5410-clock.txt new file mode 100644 index 000000000000..aeab635b07b5 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/exynos5410-clock.txt @@ -0,0 +1,45 @@ +* Samsung Exynos5410 Clock Controller + +The Exynos5410 clock controller generates and supplies clock to various +controllers within the Exynos5410 SoC. + +Required Properties: + +- compatible: should be "samsung,exynos5410-clock" + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos5410.h header and can be used in device +tree sources. + +External clock: + +There is clock that is generated outside the SoC. It +is expected that it is defined using standard clock bindings +with following clock-output-name: + + - "fin_pll" - PLL input clock from XXTI + +Example 1: An example of a clock controller node is listed below. + + clock: clock-controller@0x10010000 { + compatible = "samsung,exynos5410-clock"; + reg = <0x10010000 0x30000>; + #clock-cells = <1>; + }; + +Example 2: UART controller node that consumes the clock generated by the clock + controller. Refer to the standard clock bindings for information + about 'clocks' and 'clock-names' property. + + serial@12C20000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C00000 0x100>; + interrupts = <0 51 0>; + clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>; + clock-names = "uart", "clk_uart_baud0"; + }; diff --git a/Documentation/devicetree/bindings/clock/exynos5420-clock.txt b/Documentation/devicetree/bindings/clock/exynos5420-clock.txt index 458f34789e5d..d54f42cf0440 100644 --- a/Documentation/devicetree/bindings/clock/exynos5420-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5420-clock.txt @@ -1,196 +1,25 @@ * Samsung Exynos5420 Clock Controller The Exynos5420 clock controller generates and supplies clock to various -controllers within the Exynos5420 SoC. +controllers within the Exynos5420 SoC and for the Exynos5800 SoC. Required Properties: - compatible: should be one of the following. - "samsung,exynos5420-clock" - controller compatible with Exynos5420 SoC. + - "samsung,exynos5800-clock" - controller compatible with Exynos5800 SoC. - reg: physical base address of the controller and length of memory mapped region. - #clock-cells: should be 1. -The following is the list of clocks generated by the controller. Each clock is -assigned an identifier and client nodes use this identifier to specify the -clock which they consume. +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. - - [Core Clocks] - - Clock ID - ---------------------------- - - fin_pll 1 - - [Clock Gate for Special Clocks] - - Clock ID - ---------------------------- - sclk_uart0 128 - sclk_uart1 129 - sclk_uart2 130 - sclk_uart3 131 - sclk_mmc0 132 - sclk_mmc1 133 - sclk_mmc2 134 - sclk_spi0 135 - sclk_spi1 136 - sclk_spi2 137 - sclk_i2s1 138 - sclk_i2s2 139 - sclk_pcm1 140 - sclk_pcm2 141 - sclk_spdif 142 - sclk_hdmi 143 - sclk_pixel 144 - sclk_dp1 145 - sclk_mipi1 146 - sclk_fimd1 147 - sclk_maudio0 148 - sclk_maupcm0 149 - sclk_usbd300 150 - sclk_usbd301 151 - sclk_usbphy300 152 - sclk_usbphy301 153 - sclk_unipro 154 - sclk_pwm 155 - sclk_gscl_wa 156 - sclk_gscl_wb 157 - sclk_hdmiphy 158 - - [Peripheral Clock Gates] - - Clock ID - ---------------------------- - - aclk66_peric 256 - uart0 257 - uart1 258 - uart2 259 - uart3 260 - i2c0 261 - i2c1 262 - i2c2 263 - i2c3 264 - i2c4 265 - i2c5 266 - i2c6 267 - i2c7 268 - i2c_hdmi 269 - tsadc 270 - spi0 271 - spi1 272 - spi2 273 - keyif 274 - i2s1 275 - i2s2 276 - pcm1 277 - pcm2 278 - pwm 279 - spdif 280 - i2c8 281 - i2c9 282 - i2c10 283 - aclk66_psgen 300 - chipid 301 - sysreg 302 - tzpc0 303 - tzpc1 304 - tzpc2 305 - tzpc3 306 - tzpc4 307 - tzpc5 308 - tzpc6 309 - tzpc7 310 - tzpc8 311 - tzpc9 312 - hdmi_cec 313 - seckey 314 - mct 315 - wdt 316 - rtc 317 - tmu 318 - tmu_gpu 319 - pclk66_gpio 330 - aclk200_fsys2 350 - mmc0 351 - mmc1 352 - mmc2 353 - sromc 354 - ufs 355 - aclk200_fsys 360 - tsi 361 - pdma0 362 - pdma1 363 - rtic 364 - usbh20 365 - usbd300 366 - usbd301 377 - aclk400_mscl 380 - mscl0 381 - mscl1 382 - mscl2 383 - smmu_mscl0 384 - smmu_mscl1 385 - smmu_mscl2 386 - aclk333 400 - mfc 401 - smmu_mfcl 402 - smmu_mfcr 403 - aclk200_disp1 410 - dsim1 411 - dp1 412 - hdmi 413 - aclk300_disp1 420 - fimd1 421 - smmu_fimd1 422 - aclk166 430 - mixer 431 - aclk266 440 - rotator 441 - mdma1 442 - smmu_rotator 443 - smmu_mdma1 444 - aclk300_jpeg 450 - jpeg 451 - jpeg2 452 - smmu_jpeg 453 - aclk300_gscl 460 - smmu_gscl0 461 - smmu_gscl1 462 - gscl_wa 463 - gscl_wb 464 - gscl0 465 - gscl1 466 - clk_3aa 467 - aclk266_g2d 470 - sss 471 - slim_sss 472 - mdma0 473 - aclk333_g2d 480 - g2d 481 - aclk333_432_gscl 490 - smmu_3aa 491 - smmu_fimcl0 492 - smmu_fimcl1 493 - smmu_fimcl3 494 - fimc_lite3 495 - aclk_g3d 500 - g3d 501 - smmu_mixer 502 - - Mux ID - ---------------------------- - - mout_hdmi 640 - - Divider ID - ---------------------------- - - dout_pixel 768 +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos5420.h header and can be used in device +tree sources. Example 1: An example of a clock controller node is listed below. @@ -208,6 +37,6 @@ Example 2: UART controller node that consumes the clock generated by the clock compatible = "samsung,exynos4210-uart"; reg = <0x13820000 0x100>; interrupts = <0 54 0>; - clocks = <&clock 259>, <&clock 130>; + clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>; clock-names = "uart", "clk_uart_baud0"; }; diff --git a/Documentation/devicetree/bindings/clock/exynos5440-clock.txt b/Documentation/devicetree/bindings/clock/exynos5440-clock.txt index 9955dc9c7d96..5f7005f73058 100644 --- a/Documentation/devicetree/bindings/clock/exynos5440-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5440-clock.txt @@ -12,45 +12,12 @@ Required Properties: - #clock-cells: should be 1. -The following is the list of clocks generated by the controller. Each clock is -assigned an identifier and client nodes use this identifier to specify the -clock which they consume. - - - [Core Clocks] - - Clock ID - ---------------------------- - - xtal 1 - arm_clk 2 - - [Peripheral Clock Gates] - - Clock ID - ---------------------------- - - spi_baud 16 - pb0_250 17 - pr0_250 18 - pr1_250 19 - b_250 20 - b_125 21 - b_200 22 - sata 23 - usb 24 - gmac0 25 - cs250 26 - pb0_250_o 27 - pr0_250_o 28 - pr1_250_o 29 - b_250_o 30 - b_125_o 31 - b_200_o 32 - sata_o 33 - usb_o 34 - gmac0_o 35 - cs250_o 36 +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos5440.h header and can be used in device +tree sources. Example: An example of a clock controller node is listed below. diff --git a/Documentation/devicetree/bindings/clock/fixed-clock.txt b/Documentation/devicetree/bindings/clock/fixed-clock.txt index 48ea0ad8ad46..0641a663ad69 100644 --- a/Documentation/devicetree/bindings/clock/fixed-clock.txt +++ b/Documentation/devicetree/bindings/clock/fixed-clock.txt @@ -12,7 +12,6 @@ Required properties: Optional properties: - clock-accuracy : accuracy of clock in ppb (parts per billion). Should be a single cell. -- gpios : From common gpio binding; gpio connection to clock enable pin. - clock-output-names : From common clock binding. Example: diff --git a/Documentation/devicetree/bindings/clock/gpio-gate-clock.txt b/Documentation/devicetree/bindings/clock/gpio-gate-clock.txt new file mode 100644 index 000000000000..d3379ff9b84b --- /dev/null +++ b/Documentation/devicetree/bindings/clock/gpio-gate-clock.txt @@ -0,0 +1,21 @@ +Binding for simple gpio gated clock. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "gpio-gate-clock". +- #clock-cells : from common clock binding; shall be set to 0. +- enable-gpios : GPIO reference for enabling and disabling the clock. + +Optional properties: +- clocks: Maximum of one parent clock is supported. + +Example: + clock { + compatible = "gpio-gate-clock"; + clocks = <&parentclk>; + #clock-cells = <0>; + enable-gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/clock/hi3620-clock.txt b/Documentation/devicetree/bindings/clock/hi3620-clock.txt index 4b71ab41be53..dad6269f52c5 100644 --- a/Documentation/devicetree/bindings/clock/hi3620-clock.txt +++ b/Documentation/devicetree/bindings/clock/hi3620-clock.txt @@ -7,6 +7,7 @@ Required Properties: - compatible: should be one of the following. - "hisilicon,hi3620-clock" - controller compatible with Hi3620 SoC. + - "hisilicon,hi3620-mmc-clock" - controller specific for Hi3620 mmc. - reg: physical base address of the controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/clock/hix5hd2-clock.txt b/Documentation/devicetree/bindings/clock/hix5hd2-clock.txt new file mode 100644 index 000000000000..7894a64887cb --- /dev/null +++ b/Documentation/devicetree/bindings/clock/hix5hd2-clock.txt @@ -0,0 +1,31 @@ +* Hisilicon Hix5hd2 Clock Controller + +The hix5hd2 clock controller generates and supplies clock to various +controllers within the hix5hd2 SoC. + +Required Properties: + +- compatible: should be "hisilicon,hix5hd2-clock" +- reg: Address and length of the register set +- #clock-cells: Should be <1> + +Each clock is assigned an identifier and client nodes use this identifier +to specify the clock which they consume. + +All these identifier could be found in <dt-bindings/clock/hix5hd2-clock.h>. + +Examples: + clock: clock@f8a22000 { + compatible = "hisilicon,hix5hd2-clock"; + reg = <0xf8a22000 0x1000>; + #clock-cells = <1>; + }; + + uart0: uart@f8b00000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0xf8b00000 0x1000>; + interrupts = <0 49 4>; + clocks = <&clock HIX5HD2_FIXED_83M>; + clock-names = "apb_pclk"; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/imx1-clock.txt b/Documentation/devicetree/bindings/clock/imx1-clock.txt new file mode 100644 index 000000000000..b7adf4e3ea98 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx1-clock.txt @@ -0,0 +1,26 @@ +* Clock bindings for Freescale i.MX1 CPUs + +Required properties: +- compatible: Should be "fsl,imx1-ccm". +- reg: Address and length of the register set. +- #clock-cells: Should be <1>. + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx1-clock.h +for the full list of i.MX1 clock IDs. + +Examples: + clks: ccm@0021b000 { + #clock-cells = <1>; + compatible = "fsl,imx1-ccm"; + reg = <0x0021b000 0x1000>; + }; + + pwm: pwm@00208000 { + #pwm-cells = <2>; + compatible = "fsl,imx1-pwm"; + reg = <0x00208000 0x1000>; + interrupts = <34>; + clocks = <&clks IMX1_CLK_DUMMY>, <&clks IMX1_CLK_PER1>; + clock-names = "ipg", "per"; + }; diff --git a/Documentation/devicetree/bindings/clock/imx21-clock.txt b/Documentation/devicetree/bindings/clock/imx21-clock.txt new file mode 100644 index 000000000000..c3b0db437c48 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx21-clock.txt @@ -0,0 +1,28 @@ +* Clock bindings for Freescale i.MX21 + +Required properties: +- compatible : Should be "fsl,imx21-ccm". +- reg : Address and length of the register set. +- interrupts : Should contain CCM interrupt. +- #clock-cells: Should be <1>. + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx21-clock.h +for the full list of i.MX21 clock IDs. + +Examples: + clks: ccm@10027000{ + compatible = "fsl,imx21-ccm"; + reg = <0x10027000 0x800>; + #clock-cells = <1>; + }; + + uart1: serial@1000a000 { + compatible = "fsl,imx21-uart"; + reg = <0x1000a000 0x1000>; + interrupts = <20>; + clocks = <&clks IMX21_CLK_UART1_IPG_GATE>, + <&clks IMX21_CLK_PER1>; + clock-names = "ipg", "per"; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/imx25-clock.txt b/Documentation/devicetree/bindings/clock/imx25-clock.txt index db4f2f05c4d0..ba6b312ff8a5 100644 --- a/Documentation/devicetree/bindings/clock/imx25-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx25-clock.txt @@ -139,6 +139,9 @@ clocks and IDs. uart5_ipg 124 reserved 125 wdt_ipg 126 + cko_div 127 + cko_sel 128 + cko 129 Examples: diff --git a/Documentation/devicetree/bindings/clock/imx27-clock.txt b/Documentation/devicetree/bindings/clock/imx27-clock.txt index 7a2070393732..cc05de9ec393 100644 --- a/Documentation/devicetree/bindings/clock/imx27-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx27-clock.txt @@ -7,112 +7,22 @@ Required properties: - #clock-cells: Should be <1> The clock consumer should specify the desired clock by having the clock -ID in its "clocks" phandle cell. The following is a full list of i.MX27 -clocks and IDs. - - Clock ID - ----------------------- - dummy 0 - ckih 1 - ckil 2 - mpll 3 - spll 4 - mpll_main2 5 - ahb 6 - ipg 7 - nfc_div 8 - per1_div 9 - per2_div 10 - per3_div 11 - per4_div 12 - vpu_sel 13 - vpu_div 14 - usb_div 15 - cpu_sel 16 - clko_sel 17 - cpu_div 18 - clko_div 19 - ssi1_sel 20 - ssi2_sel 21 - ssi1_div 22 - ssi2_div 23 - clko_en 24 - ssi2_ipg_gate 25 - ssi1_ipg_gate 26 - slcdc_ipg_gate 27 - sdhc3_ipg_gate 28 - sdhc2_ipg_gate 29 - sdhc1_ipg_gate 30 - scc_ipg_gate 31 - sahara_ipg_gate 32 - rtc_ipg_gate 33 - pwm_ipg_gate 34 - owire_ipg_gate 35 - lcdc_ipg_gate 36 - kpp_ipg_gate 37 - iim_ipg_gate 38 - i2c2_ipg_gate 39 - i2c1_ipg_gate 40 - gpt6_ipg_gate 41 - gpt5_ipg_gate 42 - gpt4_ipg_gate 43 - gpt3_ipg_gate 44 - gpt2_ipg_gate 45 - gpt1_ipg_gate 46 - gpio_ipg_gate 47 - fec_ipg_gate 48 - emma_ipg_gate 49 - dma_ipg_gate 50 - cspi3_ipg_gate 51 - cspi2_ipg_gate 52 - cspi1_ipg_gate 53 - nfc_baud_gate 54 - ssi2_baud_gate 55 - ssi1_baud_gate 56 - vpu_baud_gate 57 - per4_gate 58 - per3_gate 59 - per2_gate 60 - per1_gate 61 - usb_ahb_gate 62 - slcdc_ahb_gate 63 - sahara_ahb_gate 64 - lcdc_ahb_gate 65 - vpu_ahb_gate 66 - fec_ahb_gate 67 - emma_ahb_gate 68 - emi_ahb_gate 69 - dma_ahb_gate 70 - csi_ahb_gate 71 - brom_ahb_gate 72 - ata_ahb_gate 73 - wdog_ipg_gate 74 - usb_ipg_gate 75 - uart6_ipg_gate 76 - uart5_ipg_gate 77 - uart4_ipg_gate 78 - uart3_ipg_gate 79 - uart2_ipg_gate 80 - uart1_ipg_gate 81 - ckih_div1p5 82 - fpm 83 - mpll_osc_sel 84 - mpll_sel 85 - spll_gate 86 +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx27-clock.h +for the full list of i.MX27 clock IDs. Examples: + clks: ccm@10027000{ + compatible = "fsl,imx27-ccm"; + reg = <0x10027000 0x1000>; + #clock-cells = <1>; + }; -clks: ccm@10027000{ - compatible = "fsl,imx27-ccm"; - reg = <0x10027000 0x1000>; - #clock-cells = <1>; -}; - -uart1: serial@1000a000 { - compatible = "fsl,imx27-uart", "fsl,imx21-uart"; - reg = <0x1000a000 0x1000>; - interrupts = <20>; - clocks = <&clks 81>, <&clks 61>; - clock-names = "ipg", "per"; - status = "disabled"; -}; + uart1: serial@1000a000 { + compatible = "fsl,imx27-uart", "fsl,imx21-uart"; + reg = <0x1000a000 0x1000>; + interrupts = <20>; + clocks = <&clks IMX27_CLK_UART1_IPG_GATE>, + <&clks IMX27_CLK_PER1_GATE>; + clock-names = "ipg", "per"; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/imx6q-clock.txt b/Documentation/devicetree/bindings/clock/imx6q-clock.txt index 6aab72bf67ea..9252912a5b0e 100644 --- a/Documentation/devicetree/bindings/clock/imx6q-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx6q-clock.txt @@ -7,222 +7,13 @@ Required properties: - #clock-cells: Should be <1> The clock consumer should specify the desired clock by having the clock -ID in its "clocks" phandle cell. The following is a full list of i.MX6Q -clocks and IDs. - - Clock ID - --------------------------- - dummy 0 - ckil 1 - ckih 2 - osc 3 - pll2_pfd0_352m 4 - pll2_pfd1_594m 5 - pll2_pfd2_396m 6 - pll3_pfd0_720m 7 - pll3_pfd1_540m 8 - pll3_pfd2_508m 9 - pll3_pfd3_454m 10 - pll2_198m 11 - pll3_120m 12 - pll3_80m 13 - pll3_60m 14 - twd 15 - step 16 - pll1_sw 17 - periph_pre 18 - periph2_pre 19 - periph_clk2_sel 20 - periph2_clk2_sel 21 - axi_sel 22 - esai_sel 23 - asrc_sel 24 - spdif_sel 25 - gpu2d_axi 26 - gpu3d_axi 27 - gpu2d_core_sel 28 - gpu3d_core_sel 29 - gpu3d_shader_sel 30 - ipu1_sel 31 - ipu2_sel 32 - ldb_di0_sel 33 - ldb_di1_sel 34 - ipu1_di0_pre_sel 35 - ipu1_di1_pre_sel 36 - ipu2_di0_pre_sel 37 - ipu2_di1_pre_sel 38 - ipu1_di0_sel 39 - ipu1_di1_sel 40 - ipu2_di0_sel 41 - ipu2_di1_sel 42 - hsi_tx_sel 43 - pcie_axi_sel 44 - ssi1_sel 45 - ssi2_sel 46 - ssi3_sel 47 - usdhc1_sel 48 - usdhc2_sel 49 - usdhc3_sel 50 - usdhc4_sel 51 - enfc_sel 52 - emi_sel 53 - emi_slow_sel 54 - vdo_axi_sel 55 - vpu_axi_sel 56 - cko1_sel 57 - periph 58 - periph2 59 - periph_clk2 60 - periph2_clk2 61 - ipg 62 - ipg_per 63 - esai_pred 64 - esai_podf 65 - asrc_pred 66 - asrc_podf 67 - spdif_pred 68 - spdif_podf 69 - can_root 70 - ecspi_root 71 - gpu2d_core_podf 72 - gpu3d_core_podf 73 - gpu3d_shader 74 - ipu1_podf 75 - ipu2_podf 76 - ldb_di0_podf 77 - ldb_di1_podf 78 - ipu1_di0_pre 79 - ipu1_di1_pre 80 - ipu2_di0_pre 81 - ipu2_di1_pre 82 - hsi_tx_podf 83 - ssi1_pred 84 - ssi1_podf 85 - ssi2_pred 86 - ssi2_podf 87 - ssi3_pred 88 - ssi3_podf 89 - uart_serial_podf 90 - usdhc1_podf 91 - usdhc2_podf 92 - usdhc3_podf 93 - usdhc4_podf 94 - enfc_pred 95 - enfc_podf 96 - emi_podf 97 - emi_slow_podf 98 - vpu_axi_podf 99 - cko1_podf 100 - axi 101 - mmdc_ch0_axi_podf 102 - mmdc_ch1_axi_podf 103 - arm 104 - ahb 105 - apbh_dma 106 - asrc 107 - can1_ipg 108 - can1_serial 109 - can2_ipg 110 - can2_serial 111 - ecspi1 112 - ecspi2 113 - ecspi3 114 - ecspi4 115 - ecspi5 116 - enet 117 - esai 118 - gpt_ipg 119 - gpt_ipg_per 120 - gpu2d_core 121 - gpu3d_core 122 - hdmi_iahb 123 - hdmi_isfr 124 - i2c1 125 - i2c2 126 - i2c3 127 - iim 128 - enfc 129 - ipu1 130 - ipu1_di0 131 - ipu1_di1 132 - ipu2 133 - ipu2_di0 134 - ldb_di0 135 - ldb_di1 136 - ipu2_di1 137 - hsi_tx 138 - mlb 139 - mmdc_ch0_axi 140 - mmdc_ch1_axi 141 - ocram 142 - openvg_axi 143 - pcie_axi 144 - pwm1 145 - pwm2 146 - pwm3 147 - pwm4 148 - per1_bch 149 - gpmi_bch_apb 150 - gpmi_bch 151 - gpmi_io 152 - gpmi_apb 153 - sata 154 - sdma 155 - spba 156 - ssi1 157 - ssi2 158 - ssi3 159 - uart_ipg 160 - uart_serial 161 - usboh3 162 - usdhc1 163 - usdhc2 164 - usdhc3 165 - usdhc4 166 - vdo_axi 167 - vpu_axi 168 - cko1 169 - pll1_sys 170 - pll2_bus 171 - pll3_usb_otg 172 - pll4_audio 173 - pll5_video 174 - pll8_mlb 175 - pll7_usb_host 176 - pll6_enet 177 - ssi1_ipg 178 - ssi2_ipg 179 - ssi3_ipg 180 - rom 181 - usbphy1 182 - usbphy2 183 - ldb_di0_div_3_5 184 - ldb_di1_div_3_5 185 - sata_ref 186 - sata_ref_100m 187 - pcie_ref 188 - pcie_ref_125m 189 - enet_ref 190 - usbphy1_gate 191 - usbphy2_gate 192 - pll4_post_div 193 - pll5_post_div 194 - pll5_video_div 195 - eim_slow 196 - spdif 197 - cko2_sel 198 - cko2_podf 199 - cko2 200 - cko 201 - vdoa 202 - pll4_audio_div 203 - lvds1_sel 204 - lvds2_sel 205 - lvds1_gate 206 - lvds2_gate 207 +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx6qdl-clock.h +for the full list of i.MX6 Quad and DualLite clock IDs. Examples: +#include <dt-bindings/clock/imx6qdl-clock.h> + clks: ccm@020c4000 { compatible = "fsl,imx6q-ccm"; reg = <0x020c4000 0x4000>; @@ -234,7 +25,7 @@ uart1: serial@02020000 { compatible = "fsl,imx6q-uart", "fsl,imx21-uart"; reg = <0x02020000 0x4000>; interrupts = <0 26 0x04>; - clocks = <&clks 160>, <&clks 161>; + clocks = <&clks IMX6QDL_CLK_UART_IPG>, <&clks IMX6QDL_CLK_UART_SERIAL>; clock-names = "ipg", "per"; status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/imx6sx-clock.txt b/Documentation/devicetree/bindings/clock/imx6sx-clock.txt new file mode 100644 index 000000000000..22362b9b7ba3 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx6sx-clock.txt @@ -0,0 +1,13 @@ +* Clock bindings for Freescale i.MX6 SoloX + +Required properties: +- compatible: Should be "fsl,imx6sx-ccm" +- reg: Address and length of the register set +- #clock-cells: Should be <1> +- clocks: list of clock specifiers, must contain an entry for each required + entry in clock-names +- clock-names: should include entries "ckil", "osc", "ipp_di0" and "ipp_di1" + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx6sx-clock.h +for the full list of i.MX6 SoloX clock IDs. diff --git a/Documentation/devicetree/bindings/clock/lsi,axm5516-clks.txt b/Documentation/devicetree/bindings/clock/lsi,axm5516-clks.txt new file mode 100644 index 000000000000..3ce97cfe999b --- /dev/null +++ b/Documentation/devicetree/bindings/clock/lsi,axm5516-clks.txt @@ -0,0 +1,29 @@ +AXM5516 clock driver bindings +----------------------------- + +Required properties : +- compatible : shall contain "lsi,axm5516-clks" +- reg : shall contain base register location and length +- #clock-cells : shall contain 1 + +The consumer specifies the desired clock by having the clock ID in its "clocks" +phandle cell. See <dt-bindings/clock/lsi,axxia-clock.h> for the list of +supported clock IDs. + +Example: + + clks: clock-controller@2010020000 { + compatible = "lsi,axm5516-clks"; + #clock-cells = <1>; + reg = <0x20 0x10020000 0 0x20000>; + }; + + serial0: uart@2010080000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x20 0x10080000 0 0x1000>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks AXXIA_CLK_PER>; + clock-names = "apb_pclk"; + }; + }; + diff --git a/Documentation/devicetree/bindings/clock/maxim,max77686.txt b/Documentation/devicetree/bindings/clock/maxim,max77686.txt index 96ce71bbd745..9c40739a661a 100644 --- a/Documentation/devicetree/bindings/clock/maxim,max77686.txt +++ b/Documentation/devicetree/bindings/clock/maxim,max77686.txt @@ -9,13 +9,21 @@ The MAX77686 contains three 32.768khz clock outputs that can be controlled Following properties should be presend in main device node of the MFD chip. Required properties: -- #clock-cells: simple one-cell clock specifier format is used, where the - only cell is used as an index of the clock inside the provider. Following - indices are allowed: + +- #clock-cells: from common clock binding; shall be set to 1. + +Optional properties: +- clock-output-names: From common clock binding. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. Following indices are allowed: - 0: 32khz_ap clock, - 1: 32khz_cp clock, - 2: 32khz_pmic clock. +Clocks are defined as preprocessor macros in dt-bindings/clock/maxim,max77686.h +header and can be used in device tree sources. + Example: Node of the MFD chip max77686: max77686@09 { @@ -34,5 +42,5 @@ Example: Clock consumer node compatible = "bar,foo"; /* ... */ clock-names = "my-clock"; - clocks = <&max77686 2>; + clocks = <&max77686 MAX77686_CLK_PMIC>; }; diff --git a/Documentation/devicetree/bindings/clock/maxim,max77802.txt b/Documentation/devicetree/bindings/clock/maxim,max77802.txt new file mode 100644 index 000000000000..c6dc7835f06c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/maxim,max77802.txt @@ -0,0 +1,44 @@ +Binding for Maxim MAX77802 32k clock generator block + +This is a part of device tree bindings of MAX77802 multi-function device. +More information can be found in bindings/mfd/max77802.txt file. + +The MAX77802 contains two 32.768khz clock outputs that can be controlled +(gated/ungated) over I2C. + +Following properties should be present in main device node of the MFD chip. + +Required properties: +- #clock-cells: From common clock binding; shall be set to 1. + +Optional properties: +- clock-output-names: From common clock binding. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. Following indices are allowed: + - 0: 32khz_ap clock, + - 1: 32khz_cp clock. + +Clocks are defined as preprocessor macros in dt-bindings/clock/maxim,max77802.h +header and can be used in device tree sources. + +Example: Node of the MFD chip + + max77802: max77802@09 { + compatible = "maxim,max77802"; + interrupt-parent = <&wakeup_eint>; + interrupts = <26 0>; + reg = <0x09>; + #clock-cells = <1>; + + /* ... */ + }; + +Example: Clock consumer node + + foo@0 { + compatible = "bar,foo"; + /* ... */ + clock-names = "my-clock"; + clocks = <&max77802 MAX77802_CLK_32K_AP>; + }; diff --git a/Documentation/devicetree/bindings/clock/moxa,moxart-clock.txt b/Documentation/devicetree/bindings/clock/moxa,moxart-clock.txt new file mode 100644 index 000000000000..fedea84314a1 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/moxa,moxart-clock.txt @@ -0,0 +1,48 @@ +Device Tree Clock bindings for arch-moxart + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +MOXA ART SoCs allow to determine PLL output and APB frequencies +by reading registers holding multiplier and divisor information. + + +PLL: + +Required properties: +- compatible : Must be "moxa,moxart-pll-clock" +- #clock-cells : Should be 0 +- reg : Should contain registers location and length +- clocks : Should contain phandle + clock-specifier for the parent clock + +Optional properties: +- clock-output-names : Should contain clock name + + +APB: + +Required properties: +- compatible : Must be "moxa,moxart-apb-clock" +- #clock-cells : Should be 0 +- reg : Should contain registers location and length +- clocks : Should contain phandle + clock-specifier for the parent clock + +Optional properties: +- clock-output-names : Should contain clock name + + +For example: + + clk_pll: clk_pll@98100000 { + compatible = "moxa,moxart-pll-clock"; + #clock-cells = <0>; + reg = <0x98100000 0x34>; + }; + + clk_apb: clk_apb@98100000 { + compatible = "moxa,moxart-apb-clock"; + #clock-cells = <0>; + reg = <0x98100000 0x34>; + clocks = <&clk_pll>; + }; diff --git a/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt index 1e662948661e..dc5ea5b22da9 100644 --- a/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt +++ b/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt @@ -11,19 +11,41 @@ The following is a list of provided IDs and clock names on Armada 370/XP: 3 = hclk (DRAM control clock) 4 = dramclk (DDR clock) +The following is a list of provided IDs and clock names on Armada 375: + 0 = tclk (Internal Bus clock) + 1 = cpuclk (CPU clock) + 2 = l2clk (L2 Cache clock) + 3 = ddrclk (DDR clock) + +The following is a list of provided IDs and clock names on Armada 380/385: + 0 = tclk (Internal Bus clock) + 1 = cpuclk (CPU clock) + 2 = l2clk (L2 Cache clock) + 3 = ddrclk (DDR clock) + The following is a list of provided IDs and clock names on Kirkwood and Dove: 0 = tclk (Internal Bus clock) 1 = cpuclk (CPU0 clock) 2 = l2clk (L2 Cache clock derived from CPU0 clock) 3 = ddrclk (DDR controller clock derived from CPU0 clock) +The following is a list of provided IDs and clock names on Orion5x: + 0 = tclk (Internal Bus clock) + 1 = cpuclk (CPU0 clock) + 2 = ddrclk (DDR controller clock derived from CPU0 clock) + Required properties: - compatible : shall be one of the following: "marvell,armada-370-core-clock" - For Armada 370 SoC core clocks + "marvell,armada-375-core-clock" - For Armada 375 SoC core clocks + "marvell,armada-380-core-clock" - For Armada 380/385 SoC core clocks "marvell,armada-xp-core-clock" - For Armada XP SoC core clocks "marvell,dove-core-clock" - for Dove SoC core clocks "marvell,kirkwood-core-clock" - for Kirkwood SoC (except mv88f6180) "marvell,mv88f6180-core-clock" - for Kirkwood MV88f6180 SoC + "marvell,mv88f5182-core-clock" - for Orion MV88F5182 SoC + "marvell,mv88f5281-core-clock" - for Orion MV88F5281 SoC + "marvell,mv88f6183-core-clock" - for Orion MV88F6183 SoC - reg : shall be the register address of the Sample-At-Reset (SAR) register - #clock-cells : from common clock binding; shall be set to 1 diff --git a/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt index c62391fc0e39..520562a7dc2a 100644 --- a/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt +++ b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt @@ -4,7 +4,10 @@ The following is a list of provided IDs and clock names on Armada 370/XP: 0 = nand (NAND clock) Required properties: -- compatible : must be "marvell,armada-370-corediv-clock" +- compatible : must be "marvell,armada-370-corediv-clock", + "marvell,armada-375-corediv-clock", + "marvell,armada-380-corediv-clock", + - reg : must be the register address of Core Divider control register - #clock-cells : from common clock binding; shall be set to 1 - clocks : must be set to the parent's phandle diff --git a/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt index feb830130714..99c214660bdc 100644 --- a/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt +++ b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt @@ -3,14 +3,15 @@ Device Tree Clock bindings for cpu clock of Marvell EBU platforms Required properties: - compatible : shall be one of the following: "marvell,armada-xp-cpu-clock" - cpu clocks for Armada XP -- reg : Address and length of the clock complex register set +- reg : Address and length of the clock complex register set, followed + by address and length of the PMU DFS registers - #clock-cells : should be set to 1. - clocks : shall be the input parent clock phandle for the clock. cpuclk: clock-complex@d0018700 { #clock-cells = <1>; compatible = "marvell,armada-xp-cpu-clock"; - reg = <0xd0018700 0xA0>; + reg = <0xd0018700 0xA0>, <0x1c054 0x10>; clocks = <&coreclk 1>; } diff --git a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt index fc2910fa7e45..76477be742b2 100644 --- a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt +++ b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt @@ -1,9 +1,10 @@ * Gated Clock bindings for Marvell EBU SoCs -Marvell Armada 370/XP, Dove and Kirkwood allow some peripheral clocks to be -gated to save some power. The clock consumer should specify the desired clock -by having the clock ID in its "clocks" phandle cell. The clock ID is directly -mapped to the corresponding clock gating control bit in HW to ease manual clock +Marvell Armada 370/375/380/385/XP, Dove and Kirkwood allow some +peripheral clocks to be gated to save some power. The clock consumer +should specify the desired clock by having the clock ID in its +"clocks" phandle cell. The clock ID is directly mapped to the +corresponding clock gating control bit in HW to ease manual clock lookup in datasheet. The following is a list of provided IDs for Armada 370: @@ -22,6 +23,60 @@ ID Clock Peripheral 28 ddr DDR Cntrl 30 sata1 SATA Host 0 +The following is a list of provided IDs for Armada 375: +ID Clock Peripheral +----------------------------------- +2 mu Management Unit +3 pp Packet Processor +4 ptp PTP +5 pex0 PCIe 0 Clock out +6 pex1 PCIe 1 Clock out +8 audio Audio Cntrl +11 nd_clk Nand Flash Cntrl +14 sata0_link SATA 0 Link +15 sata0_core SATA 0 Core +16 usb3 USB3 Host +17 sdio SDHCI Host +18 usb USB Host +19 gop Gigabit Ethernet MAC +20 sata1_link SATA 1 Link +21 sata1_core SATA 1 Core +22 xor0 XOR DMA 0 +23 xor1 XOR DMA 0 +24 copro Coprocessor +25 tdm Time Division Mplx +28 crypto0_enc Cryptographic Unit Port 0 Encryption +29 crypto0_core Cryptographic Unit Port 0 Core +30 crypto1_enc Cryptographic Unit Port 1 Encryption +31 crypto1_core Cryptographic Unit Port 1 Core + +The following is a list of provided IDs for Armada 380/385: +ID Clock Peripheral +----------------------------------- +0 audio Audio +2 ge2 Gigabit Ethernet 2 +3 ge1 Gigabit Ethernet 1 +4 ge0 Gigabit Ethernet 0 +5 pex1 PCIe 1 +6 pex2 PCIe 2 +7 pex3 PCIe 3 +8 pex0 PCIe 0 +9 usb3h0 USB3 Host 0 +10 usb3h1 USB3 Host 1 +11 usb3d USB3 Device +13 bm Buffer Management +14 crypto0z Cryptographic 0 Z +15 sata0 SATA 0 +16 crypto1z Cryptographic 1 Z +17 sdio SDIO +18 usb2 USB 2 +21 crypto1 Cryptographic 1 +22 xor0 XOR 0 +23 crypto0 Cryptographic 0 +25 tdm Time Division Multiplexing +28 xor1 XOR 1 +30 sata1 SATA 1 + The following is a list of provided IDs for Armada XP: ID Clock Peripheral ----------------------------------- @@ -95,6 +150,8 @@ ID Clock Peripheral Required properties: - compatible : shall be one of the following: "marvell,armada-370-gating-clock" - for Armada 370 SoC clock gating + "marvell,armada-375-gating-clock" - for Armada 375 SoC clock gating + "marvell,armada-380-gating-clock" - for Armada 380/385 SoC clock gating "marvell,armada-xp-gating-clock" - for Armada XP SoC clock gating "marvell,dove-gating-clock" - for Dove SoC clock gating "marvell,kirkwood-gating-clock" - for Kirkwood SoC clock gating diff --git a/Documentation/devicetree/bindings/clock/pxa-clock.txt b/Documentation/devicetree/bindings/clock/pxa-clock.txt new file mode 100644 index 000000000000..4b4a9024bd99 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/pxa-clock.txt @@ -0,0 +1,16 @@ +* Clock bindings for Marvell PXA chips + +Required properties: +- compatible: Should be "marvell,pxa-clocks" +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell (see include/.../pxa-clock.h). + +Examples: + +pxa2xx_clks: pxa2xx_clks@41300004 { + compatible = "marvell,pxa-clocks"; + #clock-cells = <1>; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/clock/qcom,gcc.txt b/Documentation/devicetree/bindings/clock/qcom,gcc.txt index 767401f42871..aba3d254e037 100644 --- a/Documentation/devicetree/bindings/clock/qcom,gcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,gcc.txt @@ -4,9 +4,14 @@ Qualcomm Global Clock & Reset Controller Binding Required properties : - compatible : shall contain only one of the following: + "qcom,gcc-apq8064" + "qcom,gcc-apq8084" + "qcom,gcc-ipq8064" "qcom,gcc-msm8660" "qcom,gcc-msm8960" "qcom,gcc-msm8974" + "qcom,gcc-msm8974pro" + "qcom,gcc-msm8974pro-ac" - reg : shall contain base register location and length - #clock-cells : shall contain 1 diff --git a/Documentation/devicetree/bindings/clock/qcom,mmcc.txt b/Documentation/devicetree/bindings/clock/qcom,mmcc.txt index d572e9964c54..29ebf84d25af 100644 --- a/Documentation/devicetree/bindings/clock/qcom,mmcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,mmcc.txt @@ -4,6 +4,8 @@ Qualcomm Multimedia Clock & Reset Controller Binding Required properties : - compatible : shall contain only one of the following: + "qcom,mmcc-apq8064" + "qcom,mmcc-apq8084" "qcom,mmcc-msm8660" "qcom,mmcc-msm8960" "qcom,mmcc-msm8974" diff --git a/Documentation/devicetree/bindings/clock/corenet-clock.txt b/Documentation/devicetree/bindings/clock/qoriq-clock.txt index 24711af48e30..5666812fc42b 100644 --- a/Documentation/devicetree/bindings/clock/corenet-clock.txt +++ b/Documentation/devicetree/bindings/clock/qoriq-clock.txt @@ -7,6 +7,14 @@ which can then be passed to a variety of internal logic, including cores and peripheral IP blocks. Please refer to the Reference Manual for details. +All references to "1.0" and "2.0" refer to the QorIQ chassis version to +which the chip complies. + +Chassis Version Example Chips +--------------- ------------- +1.0 p4080, p5020, p5040 +2.0 t4240, b4860, t1040 + 1. Clock Block Binding Required properties: @@ -85,7 +93,7 @@ Example for clock block and clock provider: #clock-cells = <0>; compatible = "fsl,qoriq-sysclk-1.0"; clock-output-names = "sysclk"; - } + }; pll0: pll0@800 { #clock-cells = <1>; diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt index a6a352c2771e..a5f52238c80d 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt @@ -10,8 +10,13 @@ index in the group, from 0 to 31. Required Properties: - compatible: Must be one of the following + - "renesas,r7s72100-mstp-clocks" for R7S72100 (RZ) MSTP gate clocks + - "renesas,r8a7740-mstp-clocks" for R8A7740 (R-Mobile A1) MSTP gate clocks + - "renesas,r8a7779-mstp-clocks" for R8A7779 (R-Car H1) MSTP gate clocks - "renesas,r8a7790-mstp-clocks" for R8A7790 (R-Car H2) MSTP gate clocks - "renesas,r8a7791-mstp-clocks" for R8A7791 (R-Car M2) MSTP gate clocks + - "renesas,r8a7794-mstp-clocks" for R8A7794 (R-Car E2) MSTP gate clocks + - "renesas,sh73a0-mstp-clocks" for SH73A0 (SH-MobileAG5) MSTP gate clocks - "renesas,cpg-mstp-clock" for generic MSTP gate clocks - reg: Base address and length of the I/O mapped registers used by the MSTP clocks. The first register is the clock control register and is mandatory. @@ -21,9 +26,9 @@ Required Properties: must appear in the same order as the output clocks. - #clock-cells: Must be 1 - clock-output-names: The name of the clocks as free-form strings - - renesas,indices: Indices of the gate clocks into the group (0 to 31) + - renesas,clock-indices: Indices of the gate clocks into the group (0 to 31) -The clocks, clock-output-names and renesas,indices properties contain one +The clocks, clock-output-names and renesas,clock-indices properties contain one entry per gate clock. The MSTP groups are sparsely populated. Unimplemented gate clocks must not be declared. @@ -43,7 +48,7 @@ Example clock-output-names = "tpu0", "mmcif1", "sdhi3", "sdhi2", "sdhi1", "sdhi0", "mmcif0"; - renesas,clock-indices = < + clock-indices = < R8A7790_CLK_TPU0 R8A7790_CLK_MMCIF1 R8A7790_CLK_SDHI3 R8A7790_CLK_SDHI2 R8A7790_CLK_SDHI1 R8A7790_CLK_SDHI0 R8A7790_CLK_MMCIF0 diff --git a/Documentation/devicetree/bindings/clock/renesas,r8a7740-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,r8a7740-cpg-clocks.txt new file mode 100644 index 000000000000..2c03302f86ed --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,r8a7740-cpg-clocks.txt @@ -0,0 +1,41 @@ +These bindings should be considered EXPERIMENTAL for now. + +* Renesas R8A7740 Clock Pulse Generator (CPG) + +The CPG generates core clocks for the R8A7740 SoC. It includes three PLLs +and several fixed ratio and variable ratio dividers. + +Required Properties: + + - compatible: Must be "renesas,r8a7740-cpg-clocks" + + - reg: Base address and length of the memory resource used by the CPG + + - clocks: Reference to the three parent clocks + - #clock-cells: Must be 1 + - clock-output-names: The names of the clocks. Supported clocks are + "system", "pllc0", "pllc1", "pllc2", "r", "usb24s", "i", "zg", "b", + "m1", "hp", "hpp", "usbp", "s", "zb", "m3", and "cp". + + - renesas,mode: board-specific settings of the MD_CK* bits + + +Example +------- + +cpg_clocks: cpg_clocks@e6150000 { + compatible = "renesas,r8a7740-cpg-clocks"; + reg = <0xe6150000 0x10000>; + clocks = <&extal1_clk>, <&extal2_clk>, <&extalr_clk>; + #clock-cells = <1>; + clock-output-names = "system", "pllc0", "pllc1", + "pllc2", "r", + "usb24s", + "i", "zg", "b", "m1", "hp", + "hpp", "usbp", "s", "zb", "m3", + "cp"; +}; + +&cpg_clocks { + renesas,mode = <0x05>; +}; diff --git a/Documentation/devicetree/bindings/clock/renesas,r8a7779-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,r8a7779-cpg-clocks.txt new file mode 100644 index 000000000000..ed3c8cb12f4e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,r8a7779-cpg-clocks.txt @@ -0,0 +1,27 @@ +* Renesas R8A7779 Clock Pulse Generator (CPG) + +The CPG generates core clocks for the R8A7779. It includes one PLL and +several fixed ratio dividers + +Required Properties: + + - compatible: Must be "renesas,r8a7779-cpg-clocks" + - reg: Base address and length of the memory resource used by the CPG + + - clocks: Reference to the parent clock + - #clock-cells: Must be 1 + - clock-output-names: The names of the clocks. Supported clocks are "plla", + "z", "zs", "s", "s1", "p", "b", "out". + + +Example +------- + + cpg_clocks: cpg_clocks@ffc80000 { + compatible = "renesas,r8a7779-cpg-clocks"; + reg = <0 0xffc80000 0 0x30>; + clocks = <&extal_clk>; + #clock-cells = <1>; + clock-output-names = "plla", "z", "zs", "s", "s1", "p", + "b", "out"; + }; diff --git a/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt index 7b41c2fe54db..e6ad35b894f9 100644 --- a/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt @@ -8,6 +8,7 @@ Required Properties: - compatible: Must be one of - "renesas,r8a7790-cpg-clocks" for the r8a7790 CPG - "renesas,r8a7791-cpg-clocks" for the r8a7791 CPG + - "renesas,r8a7794-cpg-clocks" for the r8a7794 CPG - "renesas,rcar-gen2-cpg-clocks" for the generic R-Car Gen2 CPG - reg: Base address and length of the memory resource used by the CPG diff --git a/Documentation/devicetree/bindings/clock/renesas,rz-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,rz-cpg-clocks.txt new file mode 100644 index 000000000000..98a257492522 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,rz-cpg-clocks.txt @@ -0,0 +1,29 @@ +* Renesas RZ Clock Pulse Generator (CPG) + +The CPG generates core clocks for the RZ SoCs. It includes the PLL, variable +CPU and GPU clocks, and several fixed ratio dividers. + +Required Properties: + + - compatible: Must be one of + - "renesas,r7s72100-cpg-clocks" for the r7s72100 CPG + - "renesas,rz-cpg-clocks" for the generic RZ CPG + - reg: Base address and length of the memory resource used by the CPG + - clocks: References to possible parent clocks. Order must match clock modes + in the datasheet. For the r7s72100, this is extal, usb_x1. + - #clock-cells: Must be 1 + - clock-output-names: The names of the clocks. Supported clocks are "pll", + "i", and "g" + + +Example +------- + + cpg_clocks: cpg_clocks@fcfe0000 { + #clock-cells = <1>; + compatible = "renesas,r7s72100-cpg-clocks", + "renesas,rz-cpg-clocks"; + reg = <0xfcfe0000 0x18>; + clocks = <&extal_clk>, <&usb_x1_clk>; + clock-output-names = "pll", "i", "g"; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt new file mode 100644 index 000000000000..0c2bf5eba43e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt @@ -0,0 +1,61 @@ +* Rockchip RK3188/RK3066 Clock and Reset Unit + +The RK3188/RK3066 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3188-cru", "rockchip,rk3188a-cru" or + "rockchip,rk3066a-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3188-cru.h and +dt-bindings/clock/rk3066-cru.h headers and can be used in device tree sources. +Similar macros exist for the reset sources in these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "xin32k" - rtc clock - optional, + - "xin27m" - 27mhz crystal input on rk3066 - optional, + - "ext_hsadc" - external HSADC clock - optional, + - "ext_cif0" - external camera clock - optional, + - "ext_rmii" - external RMII clock - optional, + - "ext_jtag" - externalJTAG clock - optional + +Example: Clock controller node: + + cru: cru@20000000 { + compatible = "rockchip,rk3188-cru"; + reg = <0x20000000 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@10124000 { + compatible = "snps,dw-apb-uart"; + reg = <0x10124000 0x400>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <1>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt new file mode 100644 index 000000000000..c9fbb76573e1 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt @@ -0,0 +1,61 @@ +* Rockchip RK3288 Clock and Reset Unit + +The RK3288 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3288-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3288-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "xin32k" - rtc clock - optional, + - "ext_i2s" - external I2S clock - optional, + - "ext_hsadc" - external HSADC clock - optional, + - "ext_edp_24m" - external display port clock - optional, + - "ext_vip" - external VIP clock - optional, + - "ext_isp" - external ISP clock - optional, + - "ext_jtag" - external JTAG clock - optional + +Example: Clock controller node: + + cru: cru@20000000 { + compatible = "rockchip,rk3188-cru"; + reg = <0x20000000 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@10124000 { + compatible = "snps,dw-apb-uart"; + reg = <0x10124000 0x400>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <1>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip.txt b/Documentation/devicetree/bindings/clock/rockchip.txt index a891c823ed44..22f6769e5d4a 100644 --- a/Documentation/devicetree/bindings/clock/rockchip.txt +++ b/Documentation/devicetree/bindings/clock/rockchip.txt @@ -6,6 +6,9 @@ This binding uses the common clock binding[1]. == Gate clocks == +These bindings are deprecated! +Please use the soc specific CRU bindings instead. + The gate registers form a continuos block which makes the dt node structure a matter of taste, as either all gates can be put into one gate clock spanning all registers or they can be divided into diff --git a/Documentation/devicetree/bindings/clock/samsung,s3c2410-clock.txt b/Documentation/devicetree/bindings/clock/samsung,s3c2410-clock.txt new file mode 100644 index 000000000000..822505e715ae --- /dev/null +++ b/Documentation/devicetree/bindings/clock/samsung,s3c2410-clock.txt @@ -0,0 +1,50 @@ +* Samsung S3C2410 Clock Controller + +The S3C2410 clock controller generates and supplies clock to various controllers +within the SoC. The clock binding described here is applicable to the s3c2410, +s3c2440 and s3c2442 SoCs in the s3c24x family. + +Required Properties: + +- compatible: should be one of the following. + - "samsung,s3c2410-clock" - controller compatible with S3C2410 SoC. + - "samsung,s3c2440-clock" - controller compatible with S3C2440 SoC. + - "samsung,s3c2442-clock" - controller compatible with S3C2442 SoC. +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. Some of the clocks are available only +on a particular SoC. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/s3c2410.h header and can be used in device +tree sources. + +External clocks: + +The xti clock used as input for the plls is generated outside the SoC. It is +expected that is are defined using standard clock bindings with a +clock-output-names value of "xti". + +Example: Clock controller node: + + clocks: clock-controller@4c000000 { + compatible = "samsung,s3c2410-clock"; + reg = <0x4c000000 0x20>; + #clock-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller (refer to the standard clock bindings for information about + "clocks" and "clock-names" properties): + + serial@50004000 { + compatible = "samsung,s3c2440-uart"; + reg = <0x50004000 0x4000>; + interrupts = <1 23 3 4>, <1 23 4 4>; + clock-names = "uart", "clk_uart_baud2"; + clocks = <&clocks PCLK_UART0>, <&clocks PCLK_UART0>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/samsung,s3c2412-clock.txt b/Documentation/devicetree/bindings/clock/samsung,s3c2412-clock.txt new file mode 100644 index 000000000000..2b430960ba47 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/samsung,s3c2412-clock.txt @@ -0,0 +1,50 @@ +* Samsung S3C2412 Clock Controller + +The S3C2412 clock controller generates and supplies clock to various controllers +within the SoC. The clock binding described here is applicable to the s3c2412 +and s3c2413 SoCs in the s3c24x family. + +Required Properties: + +- compatible: should be "samsung,s3c2412-clock" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. Some of the clocks are available only +on a particular SoC. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/s3c2412.h header and can be used in device +tree sources. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xti" - crystal input - required, + - "ext" - external clock source - optional, + +Example: Clock controller node: + + clocks: clock-controller@4c000000 { + compatible = "samsung,s3c2412-clock"; + reg = <0x4c000000 0x20>; + #clock-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller (refer to the standard clock bindings for information about + "clocks" and "clock-names" properties): + + serial@50004000 { + compatible = "samsung,s3c2412-uart"; + reg = <0x50004000 0x4000>; + interrupts = <1 23 3 4>, <1 23 4 4>; + clock-names = "uart", "clk_uart_baud2", "clk_uart_baud3"; + clocks = <&clocks PCLK_UART0>, <&clocks PCLK_UART0>, + <&clocks SCLK_UART>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/samsung,s3c2443-clock.txt b/Documentation/devicetree/bindings/clock/samsung,s3c2443-clock.txt new file mode 100644 index 000000000000..e67bb05478af --- /dev/null +++ b/Documentation/devicetree/bindings/clock/samsung,s3c2443-clock.txt @@ -0,0 +1,56 @@ +* Samsung S3C2443 Clock Controller + +The S3C2443 clock controller generates and supplies clock to various controllers +within the SoC. The clock binding described here is applicable to all SoCs in +the s3c24x family starting with the s3c2443. + +Required Properties: + +- compatible: should be one of the following. + - "samsung,s3c2416-clock" - controller compatible with S3C2416 SoC. + - "samsung,s3c2443-clock" - controller compatible with S3C2443 SoC. + - "samsung,s3c2450-clock" - controller compatible with S3C2450 SoC. +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. Some of the clocks are available only +on a particular SoC. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/s3c2443.h header and can be used in device +tree sources. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xti" - crystal input - required, + - "ext" - external clock source - optional, + - "ext_i2s" - external I2S clock - optional, + - "ext_uart" - external uart clock - optional, + +Example: Clock controller node: + + clocks: clock-controller@4c000000 { + compatible = "samsung,s3c2416-clock"; + reg = <0x4c000000 0x40>; + #clock-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller (refer to the standard clock bindings for information about + "clocks" and "clock-names" properties): + + serial@50004000 { + compatible = "samsung,s3c2440-uart"; + reg = <0x50004000 0x4000>; + interrupts = <1 23 3 4>, <1 23 4 4>; + clock-names = "uart", "clk_uart_baud2", + "clk_uart_baud3"; + clocks = <&clocks PCLK_UART0>, <&clocks PCLK_UART0>, + <&clocks SCLK_UART>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/samsung,s5pv210-clock.txt b/Documentation/devicetree/bindings/clock/samsung,s5pv210-clock.txt new file mode 100644 index 000000000000..effd9401c133 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/samsung,s5pv210-clock.txt @@ -0,0 +1,78 @@ +* Samsung S5P6442/S5PC110/S5PV210 Clock Controller + +Samsung S5P6442, S5PC110 and S5PV210 SoCs contain integrated clock +controller, which generates and supplies clock to various controllers +within the SoC. + +Required Properties: + +- compatible: should be one of following: + - "samsung,s5pv210-clock" : for clock controller of Samsung + S5PC110/S5PV210 SoCs, + - "samsung,s5p6442-clock" : for clock controller of Samsung + S5P6442 SoC. + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/s5pv210.h header and can be used in device tree sources. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xxti": external crystal oscillator connected to XXTI and XXTO pins of +the SoC, + - "xusbxti": external crystal oscillator connected to XUSBXTI and XUSBXTO +pins of the SoC, + +A subset of above clocks available on given board shall be specified in +board device tree, including the system base clock, as selected by XOM[0] +pin of the SoC. Refer to generic fixed rate clock bindings +documentation[1] for more information how to specify these clocks. + +[1] Documentation/devicetree/bindings/clock/fixed-clock.txt + +Example: Clock controller node: + + clock: clock-controller@7e00f000 { + compatible = "samsung,s5pv210-clock"; + reg = <0x7e00f000 0x1000>; + #clock-cells = <1>; + }; + +Example: Required external clocks: + + xxti: clock-xxti { + compatible = "fixed-clock"; + clock-output-names = "xxti"; + clock-frequency = <24000000>; + #clock-cells = <0>; + }; + + xusbxti: clock-xusbxti { + compatible = "fixed-clock"; + clock-output-names = "xusbxti"; + clock-frequency = <24000000>; + #clock-cells = <0>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller (refer to the standard clock bindings for information about + "clocks" and "clock-names" properties): + + uart0: serial@e2900000 { + compatible = "samsung,s5pv210-uart"; + reg = <0xe2900000 0x400>; + interrupt-parent = <&vic1>; + interrupts = <10>; + clock-names = "uart", "clk_uart_baud0", + "clk_uart_baud1"; + clocks = <&clocks UART0>, <&clocks UART0>, + <&clocks SCLK_UART0>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-divmux.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-divmux.txt new file mode 100644 index 000000000000..6247652044a0 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-divmux.txt @@ -0,0 +1,49 @@ +Binding for a ST divider and multiplexer clock driver. + +This binding uses the common clock binding[1]. +Base address is located to the parent node. See clock binding[2] + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/clock/st/st,clkgen.txt + +Required properties: + +- compatible : shall be: + "st,clkgena-divmux-c65-hs", "st,clkgena-divmux" + "st,clkgena-divmux-c65-ls", "st,clkgena-divmux" + "st,clkgena-divmux-c32-odf0", "st,clkgena-divmux" + "st,clkgena-divmux-c32-odf1", "st,clkgena-divmux" + "st,clkgena-divmux-c32-odf2", "st,clkgena-divmux" + "st,clkgena-divmux-c32-odf3", "st,clkgena-divmux" + +- #clock-cells : From common clock binding; shall be set to 1. + +- clocks : From common clock binding + +- clock-output-names : From common clock binding. + +Example: + + clockgen-a@fd345000 { + reg = <0xfd345000 0xb50>; + + clk_m_a1_div1: clk-m-a1-div1 { + #clock-cells = <1>; + compatible = "st,clkgena-divmux-c32-odf1", + "st,clkgena-divmux"; + + clocks = <&clk_m_a1_osc_prediv>, + <&clk_m_a1_pll0 1>, /* PLL0 PHI1 */ + <&clk_m_a1_pll1 1>; /* PLL1 PHI1 */ + + clock-output-names = "clk-m-rx-icn-ts", + "clk-m-rx-icn-vdp-0", + "", /* unused */ + "clk-m-prv-t1-bus", + "clk-m-icn-reg-12", + "clk-m-icn-reg-10", + "", /* unused */ + "clk-m-icn-st231"; + }; + }; + diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt new file mode 100644 index 000000000000..f1fa91c68768 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt @@ -0,0 +1,36 @@ +Binding for a ST multiplexed clock driver. + +This binding supports only simple indexed multiplexers, it does not +support table based parent index to hardware value translations. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: + +- compatible : shall be: + "st,stih416-clkgenc-vcc-hd", "st,clkgen-mux" + "st,stih416-clkgenf-vcc-fvdp", "st,clkgen-mux" + "st,stih416-clkgenf-vcc-hva", "st,clkgen-mux" + "st,stih416-clkgenf-vcc-hd", "st,clkgen-mux" + "st,stih416-clkgenf-vcc-sd", "st,clkgen-mux" + "st,stih415-clkgen-a9-mux", "st,clkgen-mux" + "st,stih416-clkgen-a9-mux", "st,clkgen-mux" + "st,stih407-clkgen-a9-mux", "st,clkgen-mux" + +- #clock-cells : from common clock binding; shall be set to 0. + +- reg : A Base address and length of the register set. + +- clocks : from common clock binding + +Example: + + clk_m_hva: clk-m-hva@fd690868 { + #clock-cells = <0>; + compatible = "st,stih416-clkgenf-vcc-hva", "st,clkgen-mux"; + reg = <0xfd690868 4>; + + clocks = <&clockgen_f 1>, <&clk_m_a1_div0 3>; + }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt new file mode 100644 index 000000000000..efb51cf0c845 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt @@ -0,0 +1,51 @@ +Binding for a ST pll clock driver. + +This binding uses the common clock binding[1]. +Base address is located to the parent node. See clock binding[2] + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/clock/st/st,clkgen.txt + +Required properties: + +- compatible : shall be: + "st,clkgena-prediv-c65", "st,clkgena-prediv" + "st,clkgena-prediv-c32", "st,clkgena-prediv" + + "st,clkgena-plls-c65" + "st,plls-c32-a1x-0", "st,clkgen-plls-c32" + "st,plls-c32-a1x-1", "st,clkgen-plls-c32" + "st,stih415-plls-c32-a9", "st,clkgen-plls-c32" + "st,stih415-plls-c32-ddr", "st,clkgen-plls-c32" + "st,stih416-plls-c32-a9", "st,clkgen-plls-c32" + "st,stih416-plls-c32-ddr", "st,clkgen-plls-c32" + "st,stih407-plls-c32-a0", "st,clkgen-plls-c32" + "st,stih407-plls-c32-a9", "st,clkgen-plls-c32" + "st,stih407-plls-c32-c0_0", "st,clkgen-plls-c32" + "st,stih407-plls-c32-c0_1", "st,clkgen-plls-c32" + + "st,stih415-gpu-pll-c32", "st,clkgengpu-pll-c32" + "st,stih416-gpu-pll-c32", "st,clkgengpu-pll-c32" + +- #clock-cells : From common clock binding; shall be set to 1. + +- clocks : From common clock binding + +- clock-output-names : From common clock binding. + +Example: + + clockgen-a@fee62000 { + reg = <0xfee62000 0xb48>; + + clk_s_a0_pll: clk-s-a0-pll { + #clock-cells = <1>; + compatible = "st,clkgena-plls-c65"; + + clocks = <&clk_sysin>; + + clock-output-names = "clk-s-a0-pll0-hs", + "clk-s-a0-pll0-ls", + "clk-s-a0-pll1"; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-prediv.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-prediv.txt new file mode 100644 index 000000000000..604766c2619e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-prediv.txt @@ -0,0 +1,36 @@ +Binding for a ST pre-divider clock driver. + +This binding uses the common clock binding[1]. +Base address is located to the parent node. See clock binding[2] + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/clock/st/st,clkgen.txt + +Required properties: + +- compatible : shall be: + "st,clkgena-prediv-c65", "st,clkgena-prediv" + "st,clkgena-prediv-c32", "st,clkgena-prediv" + +- #clock-cells : From common clock binding; shall be set to 0. + +- clocks : From common clock binding + +- clock-output-names : From common clock binding. + +Example: + + clockgen-a@fd345000 { + reg = <0xfd345000 0xb50>; + + clk_m_a2_osc_prediv: clk-m-a2-osc-prediv { + #clock-cells = <0>; + compatible = "st,clkgena-prediv-c32", + "st,clkgena-prediv"; + + clocks = <&clk_sysin>; + + clock-output-names = "clk-m-a2-osc-prediv"; + }; + }; + diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-vcc.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-vcc.txt new file mode 100644 index 000000000000..109b3eddcb17 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-vcc.txt @@ -0,0 +1,61 @@ +Binding for a type of STMicroelectronics clock crossbar (VCC). + +The crossbar can take up to 4 input clocks and control up to 16 +output clocks. Not all inputs or outputs have to be in use in a +particular instantiation. Each output can be individually enabled, +select any of the input clocks and apply a divide (by 1,2,4 or 8) to +that selected clock. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: + +- compatible : shall be: + "st,stih416-clkgenc", "st,vcc" + "st,stih416-clkgenf", "st,vcc" + +- #clock-cells : from common clock binding; shall be set to 1. + +- reg : A Base address and length of the register set. + +- clocks : from common clock binding + +- clock-output-names : From common clock binding. The block has 16 + clock outputs but not all of them in a specific instance + have to be used in the SoC. If a clock name is left as + an empty string then no clock will be created for the + output associated with that string index. If fewer than + 16 strings are provided then no clocks will be created + for the remaining outputs. + +Example: + + clockgen_c_vcc: clockgen-c-vcc@0xfe8308ac { + #clock-cells = <1>; + compatible = "st,stih416-clkgenc", "st,clkgen-vcc"; + reg = <0xfe8308ac 12>; + + clocks = <&clk_s_vcc_hd>, + <&clockgen_c 1>, + <&clk_s_tmds_fromphy>, + <&clockgen_c 2>; + + clock-output-names = "clk-s-pix-hdmi", + "clk-s-pix-dvo", + "clk-s-out-dvo", + "clk-s-pix-hd", + "clk-s-hddac", + "clk-s-denc", + "clk-s-sddac", + "clk-s-pix-main", + "clk-s-pix-aux", + "clk-s-stfe-frc-0", + "clk-s-ref-mcru", + "clk-s-slave-mcru", + "clk-s-tmds-hdmi", + "clk-s-hdmi-reject-pll", + "clk-s-thsens"; + }; + diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen.txt new file mode 100644 index 000000000000..78978f1f5158 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen.txt @@ -0,0 +1,100 @@ +Binding for a Clockgen hardware block found on +certain STMicroelectronics consumer electronics SoC devices. + +A Clockgen node can contain pll, diviser or multiplexer nodes. + +We will find only the base address of the Clockgen, this base +address is common of all subnode. + + clockgen_node { + reg = <>; + + pll_node { + ... + }; + + prediv_node { + ... + }; + + divmux_node { + ... + }; + + quadfs_node { + ... + }; + + mux_node { + ... + }; + + vcc_node { + ... + }; + + flexgen_node { + ... + }; + ... + }; + +This binding uses the common clock binding[1]. +Each subnode should use the binding discribe in [2]..[7] + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/clock/st,clkgen-divmux.txt +[3] Documentation/devicetree/bindings/clock/st,clkgen-mux.txt +[4] Documentation/devicetree/bindings/clock/st,clkgen-pll.txt +[5] Documentation/devicetree/bindings/clock/st,clkgen-prediv.txt +[6] Documentation/devicetree/bindings/clock/st,vcc.txt +[7] Documentation/devicetree/bindings/clock/st,quadfs.txt +[8] Documentation/devicetree/bindings/clock/st,flexgen.txt + + +Required properties: +- reg : A Base address and length of the register set. + +Example: + + clockgen-a@fee62000 { + + reg = <0xfee62000 0xb48>; + + clk_s_a0_pll: clk-s-a0-pll { + #clock-cells = <1>; + compatible = "st,clkgena-plls-c65"; + + clocks = <&clk-sysin>; + + clock-output-names = "clk-s-a0-pll0-hs", + "clk-s-a0-pll0-ls", + "clk-s-a0-pll1"; + }; + + clk_s_a0_osc_prediv: clk-s-a0-osc-prediv { + #clock-cells = <0>; + compatible = "st,clkgena-prediv-c65", + "st,clkgena-prediv"; + + clocks = <&clk_sysin>; + + clock-output-names = "clk-s-a0-osc-prediv"; + }; + + clk_s_a0_hs: clk-s-a0-hs { + #clock-cells = <1>; + compatible = "st,clkgena-divmux-c65-hs", + "st,clkgena-divmux"; + + clocks = <&clk-s_a0_osc_prediv>, + <&clk-s_a0_pll 0>, /* pll0 hs */ + <&clk-s_a0_pll 2>; /* pll1 */ + + clock-output-names = "clk-s-fdma-0", + "clk-s-fdma-1", + ""; /* clk-s-jit-sense */ + /* fourth output unused */ + }; + }; + diff --git a/Documentation/devicetree/bindings/clock/st/st,flexgen.txt b/Documentation/devicetree/bindings/clock/st/st,flexgen.txt new file mode 100644 index 000000000000..1d3ace088172 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,flexgen.txt @@ -0,0 +1,119 @@ +Binding for a type of flexgen structure found on certain +STMicroelectronics consumer electronics SoC devices + +This structure includes: +- a clock cross bar (represented by a mux element) +- a pre and final dividers (represented by a divider and gate elements) + +Flexgen structure is a part of Clockgen[1]. + +Please find an example below: + + Clockgen block diagram + ------------------------------------------------------------------- + | Flexgen stucture | + | --------------------------------------------- | + | | ------- -------- -------- | | +clk_sysin | | | | | | | | | +---|-----------------|-->| | | | | | | | + | | | | | | | | | | | + | | ------- | | | |Pre | |Final | | | + | | |PLL0 | | | | |Dividers| |Dividers| | | + | |->| | | | | | x32 | | x32 | | | + | | | odf_0|----|-->| | | | | | | | + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | ------- | | | | | | | | | + | | | | | | | | | | | + | | ------- | | Clock | | | | | | | + | | |PLL1 | | | | | | | | | | + | |->| | | | Cross | | | | | | | + | | | odf_0|----|-->| | | | | | CLK_DIV[31:0] + | | | | | | Bar |====>| |====>| |===|=========> + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | ------- | | | | | | | | | + | | | | | | | | | | | + | | ------- | | | | | | | | | + | | |QUADFS | | | | | | | | | | + | |->| ch0|----|-->| | | | | | | | + | | | | | | | | | | | | + | | ch1|----|-->| | | | | | | | + | | | | | | | | | | | | + | | ch2|----|-->| | | DIV | | DIV | | | + | | | | | | | 1 to | | 1 to | | | + | | ch3|----|-->| | | 1024 | | 64 | | | + | ------- | | | | | | | | | + | | ------- -------- -------- | | + | -------------------------------------------- | + | | + ------------------------------------------------------------------- + +This binding uses the common clock binding[2]. + +[1] Documentation/devicetree/bindings/clock/st/st,clkgen.txt +[2] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be: + "st,flexgen" + +- #clock-cells : from common clock binding; shall be set to 1 (multiple clock + outputs). + +- clocks : must be set to the parent's phandle. it's could be output clocks of + a quadsfs or/and a pll or/and clk_sysin (up to 7 clocks) + +- clock-output-names : List of strings used to name the clock outputs. + +Example: + + clk_s_c0_flexgen: clk-s-c0-flexgen { + + #clock-cells = <1>; + compatible = "st,flexgen"; + + clocks = <&clk_s_c0_pll0 0>, + <&clk_s_c0_pll1 0>, + <&clk_s_c0_quadfs 0>, + <&clk_s_c0_quadfs 1>, + <&clk_s_c0_quadfs 2>, + <&clk_s_c0_quadfs 3>, + <&clk_sysin>; + + clock-output-names = "clk-icn-gpu", + "clk-fdma", + "clk-nand", + "clk-hva", + "clk-proc-stfe", + "clk-proc-tp", + "clk-rx-icn-dmu", + "clk-rx-icn-hva", + "clk-icn-cpu", + "clk-tx-icn-dmu", + "clk-mmc-0", + "clk-mmc-1", + "clk-jpegdec", + "clk-ext2fa9", + "clk-ic-bdisp-0", + "clk-ic-bdisp-1", + "clk-pp-dmu", + "clk-vid-dmu", + "clk-dss-lpc", + "clk-st231-aud-0", + "clk-st231-gp-1", + "clk-st231-dmu", + "clk-icn-lmi", + "clk-tx-icn-disp-1", + "clk-icn-sbc", + "clk-stfe-frc2", + "clk-eth-phy", + "clk-eth-ref-phyclk", + "clk-flash-promip", + "clk-main-disp", + "clk-aux-disp", + "clk-compo-dvp"; + }; diff --git a/Documentation/devicetree/bindings/clock/st/st,quadfs.txt b/Documentation/devicetree/bindings/clock/st/st,quadfs.txt new file mode 100644 index 000000000000..cedeb9cc8208 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,quadfs.txt @@ -0,0 +1,48 @@ +Binding for a type of quad channel digital frequency synthesizer found on +certain STMicroelectronics consumer electronics SoC devices. + +This version contains a programmable PLL which can generate up to 216, 432 +or 660MHz (from a 30MHz oscillator input) as the input to the digital +synthesizers. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be: + "st,stih416-quadfs216", "st,quadfs" + "st,stih416-quadfs432", "st,quadfs" + "st,stih416-quadfs660-E", "st,quadfs" + "st,stih416-quadfs660-F", "st,quadfs" + "st,stih407-quadfs660-C", "st,quadfs" + "st,stih407-quadfs660-D", "st,quadfs" + + +- #clock-cells : from common clock binding; shall be set to 1. + +- reg : A Base address and length of the register set. + +- clocks : from common clock binding + +- clock-output-names : From common clock binding. The block has 4 + clock outputs but not all of them in a specific instance + have to be used in the SoC. If a clock name is left as + an empty string then no clock will be created for the + output associated with that string index. If fewer than + 4 strings are provided then no clocks will be created + for the remaining outputs. + +Example: + + clockgen_e: clockgen-e@fd3208bc { + #clock-cells = <1>; + compatible = "st,stih416-quadfs660-E", "st,quadfs"; + reg = <0xfd3208bc 0xB0>; + + clocks = <&clk_sysin>; + clock-output-names = "clk-m-pix-mdtp-0", + "clk-m-pix-mdtp-1", + "clk-m-pix-mdtp-2", + "clk-m-mpelpc"; + }; diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt index c2cb7621ad2d..ed116df9c3e7 100644 --- a/Documentation/devicetree/bindings/clock/sunxi.txt +++ b/Documentation/devicetree/bindings/clock/sunxi.txt @@ -6,37 +6,56 @@ This binding uses the common clock binding[1]. Required properties: - compatible : shall be one of the following: - "allwinner,sun4i-osc-clk" - for a gatable oscillator - "allwinner,sun4i-pll1-clk" - for the main PLL clock and PLL4 + "allwinner,sun4i-a10-osc-clk" - for a gatable oscillator + "allwinner,sun4i-a10-pll1-clk" - for the main PLL clock and PLL4 "allwinner,sun6i-a31-pll1-clk" - for the main PLL clock on A31 - "allwinner,sun4i-pll5-clk" - for the PLL5 clock - "allwinner,sun4i-pll6-clk" - for the PLL6 clock - "allwinner,sun4i-cpu-clk" - for the CPU multiplexer clock - "allwinner,sun4i-axi-clk" - for the AXI clock - "allwinner,sun4i-axi-gates-clk" - for the AXI gates - "allwinner,sun4i-ahb-clk" - for the AHB clock - "allwinner,sun4i-ahb-gates-clk" - for the AHB gates on A10 + "allwinner,sun8i-a23-pll1-clk" - for the main PLL clock on A23 + "allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock + "allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock + "allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31 + "allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock + "allwinner,sun4i-a10-axi-clk" - for the AXI clock + "allwinner,sun8i-a23-axi-clk" - for the AXI clock on A23 + "allwinner,sun4i-a10-axi-gates-clk" - for the AXI gates + "allwinner,sun4i-a10-ahb-clk" - for the AHB clock + "allwinner,sun4i-a10-ahb-gates-clk" - for the AHB gates on A10 "allwinner,sun5i-a13-ahb-gates-clk" - for the AHB gates on A13 "allwinner,sun5i-a10s-ahb-gates-clk" - for the AHB gates on A10s "allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20 + "allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31 "allwinner,sun6i-a31-ahb1-mux-clk" - for the AHB1 multiplexer on A31 "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31 - "allwinner,sun4i-apb0-clk" - for the APB0 clock - "allwinner,sun4i-apb0-gates-clk" - for the APB0 gates on A10 + "allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23 + "allwinner,sun4i-a10-apb0-clk" - for the APB0 clock + "allwinner,sun6i-a31-apb0-clk" - for the APB0 clock on A31 + "allwinner,sun8i-a23-apb0-clk" - for the APB0 clock on A23 + "allwinner,sun4i-a10-apb0-gates-clk" - for the APB0 gates on A10 "allwinner,sun5i-a13-apb0-gates-clk" - for the APB0 gates on A13 "allwinner,sun5i-a10s-apb0-gates-clk" - for the APB0 gates on A10s + "allwinner,sun6i-a31-apb0-gates-clk" - for the APB0 gates on A31 "allwinner,sun7i-a20-apb0-gates-clk" - for the APB0 gates on A20 - "allwinner,sun4i-apb1-clk" - for the APB1 clock - "allwinner,sun4i-apb1-mux-clk" - for the APB1 clock muxing - "allwinner,sun4i-apb1-gates-clk" - for the APB1 gates on A10 + "allwinner,sun8i-a23-apb0-gates-clk" - for the APB0 gates on A23 + "allwinner,sun4i-a10-apb1-clk" - for the APB1 clock + "allwinner,sun4i-a10-apb1-mux-clk" - for the APB1 clock muxing + "allwinner,sun4i-a10-apb1-gates-clk" - for the APB1 gates on A10 "allwinner,sun5i-a13-apb1-gates-clk" - for the APB1 gates on A13 "allwinner,sun5i-a10s-apb1-gates-clk" - for the APB1 gates on A10s "allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31 "allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20 + "allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23 "allwinner,sun6i-a31-apb2-div-clk" - for the APB2 gates on A31 "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31 - "allwinner,sun4i-mod0-clk" - for the module 0 family of clocks + "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23 + "allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13 + "allwinner,sun4i-a10-mmc-output-clk" - for the MMC output clock on A10 + "allwinner,sun4i-a10-mmc-sample-clk" - for the MMC sample clock on A10 + "allwinner,sun4i-a10-mod0-clk" - for the module 0 family of clocks + "allwinner,sun8i-a23-mbus-clk" - for the MBUS clock on A23 "allwinner,sun7i-a20-out-clk" - for the external output clocks + "allwinner,sun7i-a20-gmac-clk" - for the GMAC clock module on A20/A31 + "allwinner,sun4i-a10-usb-clk" - for usb gates + resets on A10 / A20 + "allwinner,sun5i-a13-usb-clk" - for usb gates + resets on A13 + "allwinner,sun6i-a31-usb-clk" - for usb gates + resets on A31 Required properties for all clocks: - reg : shall be the control register address for the clock. @@ -44,10 +63,17 @@ Required properties for all clocks: multiplexed clocks, the list order must match the hardware programming order. - #clock-cells : from common clock binding; shall be set to 0 except for - "allwinner,*-gates-clk" where it shall be set to 1 + "allwinner,*-gates-clk", "allwinner,sun4i-pll5-clk" and + "allwinner,sun4i-pll6-clk" where it shall be set to 1 +- clock-output-names : shall be the corresponding names of the outputs. + If the clock module only has one output, the name shall be the + module name. -Additionally, "allwinner,*-gates-clk" clocks require: -- clock-output-names : the corresponding gate names that the clock controls +And "allwinner,*-usb-clk" clocks also require: +- reset-cells : shall be set to 1 + +For "allwinner,sun7i-a20-gmac-clk", the parent clocks shall be fixed rate +dummy clocks at 25 MHz and 125 MHz, respectively. See example. Clock consumers should specify the desired clocks they use with a "clocks" phandle cell. Consumers that are using a gated clock should @@ -56,23 +82,68 @@ offset of the bit controlling this particular gate in the register. For example: -osc24M: osc24M@01c20050 { +osc24M: clk@01c20050 { #clock-cells = <0>; - compatible = "allwinner,sun4i-osc-clk"; + compatible = "allwinner,sun4i-a10-osc-clk"; reg = <0x01c20050 0x4>; clocks = <&osc24M_fixed>; + clock-output-names = "osc24M"; }; -pll1: pll1@01c20000 { +pll1: clk@01c20000 { #clock-cells = <0>; - compatible = "allwinner,sun4i-pll1-clk"; + compatible = "allwinner,sun4i-a10-pll1-clk"; reg = <0x01c20000 0x4>; clocks = <&osc24M>; + clock-output-names = "pll1"; +}; + +pll5: clk@01c20020 { + #clock-cells = <1>; + compatible = "allwinner,sun4i-pll5-clk"; + reg = <0x01c20020 0x4>; + clocks = <&osc24M>; + clock-output-names = "pll5_ddr", "pll5_other"; }; cpu: cpu@01c20054 { #clock-cells = <0>; - compatible = "allwinner,sun4i-cpu-clk"; + compatible = "allwinner,sun4i-a10-cpu-clk"; reg = <0x01c20054 0x4>; clocks = <&osc32k>, <&osc24M>, <&pll1>; + clock-output-names = "cpu"; +}; + +mmc0_clk: clk@01c20088 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-mod0-clk"; + reg = <0x01c20088 0x4>; + clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; + clock-output-names = "mmc0"; +}; + +mii_phy_tx_clk: clk@2 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <25000000>; + clock-output-names = "mii_phy_tx"; +}; + +gmac_int_tx_clk: clk@3 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <125000000>; + clock-output-names = "gmac_int_tx"; +}; + +gmac_clk: clk@01c20164 { + #clock-cells = <0>; + compatible = "allwinner,sun7i-a20-gmac-clk"; + reg = <0x01c20164 0x4>; + /* + * The first clock must be fixed at 25MHz; + * the second clock must be fixed at 125MHz + */ + clocks = <&mii_phy_tx_clk>, <&gmac_int_tx_clk>; + clock-output-names = "gmac"; }; diff --git a/Documentation/devicetree/bindings/clock/ti-keystone-pllctrl.txt b/Documentation/devicetree/bindings/clock/ti-keystone-pllctrl.txt new file mode 100644 index 000000000000..3e6a81e99804 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti-keystone-pllctrl.txt @@ -0,0 +1,20 @@ +* Device tree bindings for Texas Instruments keystone pll controller + +The main pll controller used to drive theC66x CorePacs, the switch fabric, +and a majority of the peripheral clocks (all but the ARM CorePacs, DDR3 and +the NETCP modules) requires a PLL Controller to manage the various clock +divisions, gating, and synchronization. + +Required properties: + +- compatible: "ti,keystone-pllctrl", "syscon" + +- reg: contains offset/length value for pll controller + registers space. + +Example: + +pllctrl: pll-controller@0x02310000 { + compatible = "ti,keystone-pllctrl", "syscon"; + reg = <0x02310000 0x200>; +}; diff --git a/Documentation/devicetree/bindings/clock/ti/apll.txt b/Documentation/devicetree/bindings/clock/ti/apll.txt index 7faf5a68b3be..ade4dd4c30f0 100644 --- a/Documentation/devicetree/bindings/clock/ti/apll.txt +++ b/Documentation/devicetree/bindings/clock/ti/apll.txt @@ -14,18 +14,32 @@ a subtype of a DPLL [2], although a simplified one at that. [2] Documentation/devicetree/bindings/clock/ti/dpll.txt Required properties: -- compatible : shall be "ti,dra7-apll-clock" +- compatible : shall be "ti,dra7-apll-clock" or "ti,omap2-apll-clock" - #clock-cells : from common clock binding; shall be set to 0. - clocks : link phandles of parent clocks (clk-ref and clk-bypass) - reg : address and length of the register set for controlling the APLL. It contains the information of registers in the following order: - "control" - contains the control register base address - "idlest" - contains the idlest register base address + "control" - contains the control register offset + "idlest" - contains the idlest register offset + "autoidle" - contains the autoidle register offset (OMAP2 only) +- ti,clock-frequency : static clock frequency for the clock (OMAP2 only) +- ti,idlest-shift : bit-shift for the idlest field (OMAP2 only) +- ti,bit-shift : bit-shift for enable and autoidle fields (OMAP2 only) Examples: - apll_pcie_ck: apll_pcie_ck@4a008200 { + apll_pcie_ck: apll_pcie_ck { #clock-cells = <0>; clocks = <&apll_pcie_in_clk_mux>, <&dpll_pcie_ref_ck>; - reg = <0x4a00821c 0x4>, <0x4a008220 0x4>; + reg = <0x021c>, <0x0220>; compatible = "ti,dra7-apll-clock"; }; + + apll96_ck: apll96_ck { + #clock-cells = <0>; + compatible = "ti,omap2-apll-clock"; + clocks = <&sys_ck>; + ti,bit-shift = <2>; + ti,idlest-shift = <8>; + ti,clock-frequency = <96000000>; + reg = <0x0500>, <0x0530>, <0x0520>; + }; diff --git a/Documentation/devicetree/bindings/clock/ti/dpll.txt b/Documentation/devicetree/bindings/clock/ti/dpll.txt index 30bfdb7c9f18..df57009ff8e7 100644 --- a/Documentation/devicetree/bindings/clock/ti/dpll.txt +++ b/Documentation/devicetree/bindings/clock/ti/dpll.txt @@ -24,12 +24,14 @@ Required properties: "ti,omap4-dpll-core-clock", "ti,omap4-dpll-m4xen-clock", "ti,omap4-dpll-j-type-clock", + "ti,omap5-mpu-dpll-clock", "ti,am3-dpll-no-gate-clock", "ti,am3-dpll-j-type-clock", "ti,am3-dpll-no-gate-j-type-clock", "ti,am3-dpll-clock", "ti,am3-dpll-core-clock", "ti,am3-dpll-x2-clock", + "ti,omap2-dpll-core-clock", - #clock-cells : from common clock binding; shall be set to 0. - clocks : link phandles of parent clocks, first entry lists reference clock @@ -41,6 +43,7 @@ Required properties: "mult-div1" - contains the multiplier / divider register base address "autoidle" - contains the autoidle register base address (optional) ti,am3-* dpll types do not have autoidle register + ti,omap2-* dpll type does not support idlest / autoidle registers Optional properties: - DPLL mode setting - defining any one or more of the following overrides @@ -73,3 +76,10 @@ Examples: clocks = <&sys_clkin_ck>, <&sys_clkin_ck>; reg = <0x90>, <0x5c>, <0x68>; }; + + dpll_ck: dpll_ck { + #clock-cells = <0>; + compatible = "ti,omap2-dpll-core-clock"; + clocks = <&sys_ck>, <&sys_ck>; + reg = <0x0500>, <0x0540>; + }; diff --git a/Documentation/devicetree/bindings/clock/ti/dra7-atl.txt b/Documentation/devicetree/bindings/clock/ti/dra7-atl.txt new file mode 100644 index 000000000000..585e8c191f50 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/dra7-atl.txt @@ -0,0 +1,96 @@ +Device Tree Clock bindings for ATL (Audio Tracking Logic) of DRA7 SoC. + +The ATL IP is used to generate clock to be used to synchronize baseband and +audio codec. A single ATL IP provides four ATL clock instances sharing the same +functional clock but can be configured to provide different clocks. +ATL can maintain a clock averages to some desired frequency based on the bws/aws +signals - can compensate the drift between the two ws signal. + +In order to provide the support for ATL and it's output clocks (which can be used +internally within the SoC or external components) two sets of bindings is needed: + +Clock tree binding: +This binding uses the common clock binding[1]. +To be able to integrate the ATL clocks with DT clock tree. +Provides ccf level representation of the ATL clocks to be used by drivers. +Since the clock instances are part of a single IP this binding is used as a node +for the DT clock tree, the IP driver is needed to handle the actual configuration +of the IP. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "ti,dra7-atl-clock" +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : link phandles to functional clock of ATL + +Binding for the IP driver: +This binding is used to configure the IP driver which is going to handle the +configuration of the IP for the ATL clock instances. + +Required properties: +- compatible : shall be "ti,dra7-atl" +- reg : base address for the ATL IP +- ti,provided-clocks : List of phandles to the clocks associated with the ATL +- clocks : link phandles to functional clock of ATL +- clock-names : Shall be set to "fck" +- ti,hwmods : Shall be set to "atl" + +Optional properties: +Configuration of ATL instances: +- atl{0/1/2/3} { + - bws : Baseband word select signal selection + - aws : Audio word select signal selection +}; + +For valid word select signals, see the dt-bindings/clk/ti-dra7-atl.h include +file. + +Examples: +/* clock bindings for atl provided clocks */ +atl_clkin0_ck: atl_clkin0_ck { + #clock-cells = <0>; + compatible = "ti,dra7-atl-clock"; + clocks = <&atl_gfclk_mux>; +}; + +atl_clkin1_ck: atl_clkin1_ck { + #clock-cells = <0>; + compatible = "ti,dra7-atl-clock"; + clocks = <&atl_gfclk_mux>; +}; + +atl_clkin2_ck: atl_clkin2_ck { + #clock-cells = <0>; + compatible = "ti,dra7-atl-clock"; + clocks = <&atl_gfclk_mux>; +}; + +atl_clkin3_ck: atl_clkin3_ck { + #clock-cells = <0>; + compatible = "ti,dra7-atl-clock"; + clocks = <&atl_gfclk_mux>; +}; + +/* binding for the IP */ +atl: atl@4843c000 { + compatible = "ti,dra7-atl"; + reg = <0x4843c000 0x3ff>; + ti,hwmods = "atl"; + ti,provided-clocks = <&atl_clkin0_ck>, <&atl_clkin1_ck>, + <&atl_clkin2_ck>, <&atl_clkin3_ck>; + clocks = <&atl_gfclk_mux>; + clock-names = "fck"; + status = "disabled"; +}; + +#include <dt-bindings/clk/ti-dra7-atl.h> + +&atl { + status = "okay"; + + atl2 { + bws = <DRA7_ATL_WS_MCASP2_FSX>; + aws = <DRA7_ATL_WS_MCASP3_FSX>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/ti/gate.txt b/Documentation/devicetree/bindings/clock/ti/gate.txt index 125281aaa4ca..03f8fdee62a7 100644 --- a/Documentation/devicetree/bindings/clock/ti/gate.txt +++ b/Documentation/devicetree/bindings/clock/ti/gate.txt @@ -25,6 +25,11 @@ Required properties: to map clockdomains properly "ti,hsdiv-gate-clock" - gate clock with OMAP36xx specific hardware handling, required for a hardware errata + "ti,composite-gate-clock" - composite gate clock, to be part of composite + clock + "ti,composite-no-wait-gate-clock" - composite gate clock that does not wait + for clock to be active before returning + from clk_enable() - #clock-cells : from common clock binding; shall be set to 0 - clocks : link to phandle of parent clock - reg : offset for register controlling adjustable gate, not needed for @@ -41,7 +46,7 @@ Examples: #clock-cells = <0>; compatible = "ti,gate-clock"; clocks = <&core_96m_fck>; - reg = <0x48004a00 0x4>; + reg = <0x0a00>; ti,bit-shift = <25>; }; @@ -57,7 +62,7 @@ Examples: #clock-cells = <0>; compatible = "ti,dss-gate-clock"; clocks = <&dpll4_m4x2_ck>; - reg = <0x48004e00 0x4>; + reg = <0x0e00>; ti,bit-shift = <0>; }; @@ -65,7 +70,7 @@ Examples: #clock-cells = <0>; compatible = "ti,am35xx-gate-clock"; clocks = <&ipss_ick>; - reg = <0x4800259c 0x4>; + reg = <0x059c>; ti,bit-shift = <1>; }; @@ -80,6 +85,22 @@ Examples: compatible = "ti,hsdiv-gate-clock"; clocks = <&dpll4_m2x2_mul_ck>; ti,bit-shift = <0x1b>; - reg = <0x48004d00 0x4>; + reg = <0x0d00>; ti,set-bit-to-disable; }; + + vlynq_gate_fck: vlynq_gate_fck { + #clock-cells = <0>; + compatible = "ti,composite-gate-clock"; + clocks = <&core_ck>; + ti,bit-shift = <3>; + reg = <0x0200>; + }; + + sys_clkout2_src_gate: sys_clkout2_src_gate { + #clock-cells = <0>; + compatible = "ti,composite-no-wait-gate-clock"; + clocks = <&core_ck>; + ti,bit-shift = <15>; + reg = <0x0070>; + }; diff --git a/Documentation/devicetree/bindings/clock/ti/interface.txt b/Documentation/devicetree/bindings/clock/ti/interface.txt index 064e8caccac3..3111a409fea6 100644 --- a/Documentation/devicetree/bindings/clock/ti/interface.txt +++ b/Documentation/devicetree/bindings/clock/ti/interface.txt @@ -21,6 +21,8 @@ Required properties: "ti,omap3-dss-interface-clock" - interface clock with DSS specific HW handling "ti,omap3-ssi-interface-clock" - interface clock with SSI specific HW handling "ti,am35xx-interface-clock" - interface clock with AM35xx specific HW handling + "ti,omap2430-interface-clock" - interface clock with OMAP2430 specific HW + handling - #clock-cells : from common clock binding; shall be set to 0 - clocks : link to phandle of parent clock - reg : base address for the control register diff --git a/Documentation/devicetree/bindings/clock/vf610-clock.txt b/Documentation/devicetree/bindings/clock/vf610-clock.txt index c80863d344ac..63f9f1ac3439 100644 --- a/Documentation/devicetree/bindings/clock/vf610-clock.txt +++ b/Documentation/devicetree/bindings/clock/vf610-clock.txt @@ -5,6 +5,19 @@ Required properties: - reg: Address and length of the register set - #clock-cells: Should be <1> +Optional properties: +- clocks: list of clock identifiers which are external input clocks to the + given clock controller. Please refer the next section to find + the input clocks for a given controller. +- clock-names: list of names of clocks which are exteral input clocks to the + given clock controller. + +Input clocks for top clock controller: + - sxosc (external crystal oscillator 32KHz, recommended) + - fxosc (external crystal oscillator 24MHz, recommended) + - audio_ext + - enet_ext + The clock consumer should specify the desired clock by having the clock ID in its "clocks" phandle cell. See include/dt-bindings/clock/vf610-clock.h for the full list of VF610 clock IDs. @@ -15,6 +28,8 @@ clks: ccm@4006b000 { compatible = "fsl,vf610-ccm"; reg = <0x4006b000 0x1000>; #clock-cells = <1>; + clocks = <&sxosc>, <&fxosc>; + clock-names = "sxosc", "fxosc"; }; uart1: serial@40028000 { diff --git a/Documentation/devicetree/bindings/clock/zynq-7000.txt b/Documentation/devicetree/bindings/clock/zynq-7000.txt index 17b4a94916d6..d93746cf2975 100644 --- a/Documentation/devicetree/bindings/clock/zynq-7000.txt +++ b/Documentation/devicetree/bindings/clock/zynq-7000.txt @@ -14,6 +14,7 @@ for all clock consumers of PS clocks. Required properties: - #clock-cells : Must be 1 - compatible : "xlnx,ps7-clkc" + - reg : SLCR offset and size taken via syscon < 0x100 0x100 > - ps-clk-frequency : Frequency of the oscillator providing ps_clk in HZ (usually 33 MHz oscillators are used for Zynq platforms) - clock-output-names : List of strings used to name the clock outputs. Shall be @@ -87,10 +88,11 @@ Clock outputs: 47: dbg_apb Example: - clkc: clkc { + clkc: clkc@100 { #clock-cells = <1>; compatible = "xlnx,ps7-clkc"; ps-clk-frequency = <33333333>; + reg = <0x100 0x100>; clock-output-names = "armpll", "ddrpll", "iopll", "cpu_6or4x", "cpu_3or2x", "cpu_2x", "cpu_1x", "ddr2x", "ddr3x", "dci", "lqspi", "smc", "pcap", "gem0", "gem1", diff --git a/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt b/Documentation/devicetree/bindings/cpufreq/cpufreq-dt.txt index f055515d2b62..e41c98ffbccb 100644 --- a/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt +++ b/Documentation/devicetree/bindings/cpufreq/cpufreq-dt.txt @@ -1,17 +1,19 @@ -Generic CPU0 cpufreq driver +Generic cpufreq driver -It is a generic cpufreq driver for CPU0 frequency management. It -supports both uniprocessor (UP) and symmetric multiprocessor (SMP) -systems which share clock and voltage across all CPUs. +It is a generic DT based cpufreq driver for frequency management. It supports +both uniprocessor (UP) and symmetric multiprocessor (SMP) systems which share +clock and voltage across all CPUs. Both required and optional properties listed below must be defined under node /cpus/cpu@0. Required properties: -- operating-points: Refer to Documentation/devicetree/bindings/power/opp.txt - for details +- None Optional properties: +- operating-points: Refer to Documentation/devicetree/bindings/power/opp.txt for + details. OPPs *must* be supplied either via DT, i.e. this property, or + populated at runtime. - clock-latency: Specify the possible maximum transition latency for clock, in unit of nanoseconds. - voltage-tolerance: Specify the CPU voltage tolerance in percentage. diff --git a/Documentation/devicetree/bindings/crypto/amd-ccp.txt b/Documentation/devicetree/bindings/crypto/amd-ccp.txt new file mode 100644 index 000000000000..8c61183b41e0 --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/amd-ccp.txt @@ -0,0 +1,19 @@ +* AMD Cryptographic Coprocessor driver (ccp) + +Required properties: +- compatible: Should be "amd,ccp-seattle-v1a" +- reg: Address and length of the register set for the device +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the CCP interrupt + +Optional properties: +- dma-coherent: Present if dma operations are coherent + +Example: + ccp@e0100000 { + compatible = "amd,ccp-seattle-v1a"; + reg = <0 0xe0100000 0 0x10000>; + interrupt-parent = <&gic>; + interrupts = <0 3 4>; + }; diff --git a/Documentation/devicetree/bindings/crypto/fsl-sec6.txt b/Documentation/devicetree/bindings/crypto/fsl-sec6.txt index c0a20cd972e3..baf8a3c1b469 100644 --- a/Documentation/devicetree/bindings/crypto/fsl-sec6.txt +++ b/Documentation/devicetree/bindings/crypto/fsl-sec6.txt @@ -1,5 +1,5 @@ SEC 6 is as Freescale's Cryptographic Accelerator and Assurance Module (CAAM). -Currently Freescale powerpc chip C29X is embeded with SEC 6. +Currently Freescale powerpc chip C29X is embedded with SEC 6. SEC 6 device tree binding include: -SEC 6 Node -Job Ring Node diff --git a/Documentation/devicetree/bindings/crypto/qcom-qce.txt b/Documentation/devicetree/bindings/crypto/qcom-qce.txt new file mode 100644 index 000000000000..fdd53b184ba8 --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/qcom-qce.txt @@ -0,0 +1,25 @@ +Qualcomm crypto engine driver + +Required properties: + +- compatible : should be "qcom,crypto-v5.1" +- reg : specifies base physical address and size of the registers map +- clocks : phandle to clock-controller plus clock-specifier pair +- clock-names : "iface" clocks register interface + "bus" clocks data transfer interface + "core" clocks rest of the crypto block +- dmas : DMA specifiers for tx and rx dma channels. For more see + Documentation/devicetree/bindings/dma/dma.txt +- dma-names : DMA request names should be "rx" and "tx" + +Example: + crypto@fd45a000 { + compatible = "qcom,crypto-v5.1"; + reg = <0xfd45a000 0x6000>; + clocks = <&gcc GCC_CE2_AHB_CLK>, + <&gcc GCC_CE2_AXI_CLK>, + <&gcc GCC_CE2_CLK>; + clock-names = "iface", "bus", "core"; + dmas = <&cryptobam 2>, <&cryptobam 3>; + dma-names = "rx", "tx"; + }; diff --git a/Documentation/devicetree/bindings/crypto/samsung-sss.txt b/Documentation/devicetree/bindings/crypto/samsung-sss.txt new file mode 100644 index 000000000000..a6dafa83c6df --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/samsung-sss.txt @@ -0,0 +1,34 @@ +Samsung SoC SSS (Security SubSystem) module + +The SSS module in S5PV210 SoC supports the following: +-- Feeder (FeedCtrl) +-- Advanced Encryption Standard (AES) +-- Data Encryption Standard (DES)/3DES +-- Public Key Accelerator (PKA) +-- SHA-1/SHA-256/MD5/HMAC (SHA-1/SHA-256/MD5)/PRNG +-- PRNG: Pseudo Random Number Generator + +The SSS module in Exynos4 (Exynos4210) and +Exynos5 (Exynos5420 and Exynos5250) SoCs +supports the following also: +-- ARCFOUR (ARC4) +-- True Random Number Generator (TRNG) +-- Secure Key Manager + +Required properties: + +- compatible : Should contain entries for this and backward compatible + SSS versions: + - "samsung,s5pv210-secss" for S5PV210 SoC. + - "samsung,exynos4210-secss" for Exynos4210, Exynos4212, Exynos4412, Exynos5250, + Exynos5260 and Exynos5420 SoCs. +- reg : Offset and length of the register set for the module +- interrupts : interrupt specifiers of SSS module interrupts, should contain + following entries: + - first : feed control interrupt (required for all variants), + - second : hash interrupt (required only for samsung,s5pv210-secss). + +- clocks : list of clock phandle and specifier pairs for all clocks listed in + clock-names property. +- clock-names : list of device clock input names; should contain one entry + "secss". diff --git a/Documentation/devicetree/bindings/dma/dma.txt b/Documentation/devicetree/bindings/dma/dma.txt index 8f504e6bae14..82104271e754 100644 --- a/Documentation/devicetree/bindings/dma/dma.txt +++ b/Documentation/devicetree/bindings/dma/dma.txt @@ -14,7 +14,7 @@ Required property: Optional properties: - dma-channels: Number of DMA channels supported by the controller. -- dma-requests: Number of DMA requests signals supported by the +- dma-requests: Number of DMA request signals supported by the controller. Example: @@ -44,7 +44,7 @@ Required property: #dma-cells property in the node referenced by phandle containing DMA controller specific information. This typically contains a DMA request line number or a - channel number, but can contain any data that is used + channel number, but can contain any data that is required for configuring a channel. - dma-names: Contains one identifier string for each DMA specifier in the dmas property. The specific strings that can be used diff --git a/Documentation/devicetree/bindings/dma/fsl-edma.txt b/Documentation/devicetree/bindings/dma/fsl-edma.txt new file mode 100644 index 000000000000..191d7bd8a6fe --- /dev/null +++ b/Documentation/devicetree/bindings/dma/fsl-edma.txt @@ -0,0 +1,76 @@ +* Freescale enhanced Direct Memory Access(eDMA) Controller + + The eDMA channels have multiplex capability by programmble memory-mapped +registers. channels are split into two groups, called DMAMUX0 and DMAMUX1, +specific DMA request source can only be multiplexed by any channel of certain +group, DMAMUX0 or DMAMUX1, but not both. + +* eDMA Controller +Required properties: +- compatible : + - "fsl,vf610-edma" for eDMA used similar to that on Vybrid vf610 SoC +- reg : Specifies base physical address(s) and size of the eDMA registers. + The 1st region is eDMA control register's address and size. + The 2nd and the 3rd regions are programmable channel multiplexing + control register's address and size. +- interrupts : A list of interrupt-specifiers, one for each entry in + interrupt-names. +- interrupt-names : Should contain: + "edma-tx" - the transmission interrupt + "edma-err" - the error interrupt +- #dma-cells : Must be <2>. + The 1st cell specifies the DMAMUX(0 for DMAMUX0 and 1 for DMAMUX1). + Specific request source can only be multiplexed by specific channels + group called DMAMUX. + The 2nd cell specifies the request source(slot) ID. + See the SoC's reference manual for all the supported request sources. +- dma-channels : Number of channels supported by the controller +- clock-names : A list of channel group clock names. Should contain: + "dmamux0" - clock name of mux0 group + "dmamux1" - clock name of mux1 group +- clocks : A list of phandle and clock-specifier pairs, one for each entry in + clock-names. + +Optional properties: +- big-endian: If present registers and hardware scatter/gather descriptors + of the eDMA are implemented in big endian mode, otherwise in little + mode. + + +Examples: + +edma0: dma-controller@40018000 { + #dma-cells = <2>; + compatible = "fsl,vf610-edma"; + reg = <0x40018000 0x2000>, + <0x40024000 0x1000>, + <0x40025000 0x1000>; + interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>, + <0 9 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "edma-tx", "edma-err"; + dma-channels = <32>; + clock-names = "dmamux0", "dmamux1"; + clocks = <&clks VF610_CLK_DMAMUX0>, + <&clks VF610_CLK_DMAMUX1>; +}; + + +* DMA clients +DMA client drivers that uses the DMA function must use the format described +in the dma.txt file, using a two-cell specifier for each channel: the 1st +specifies the channel group(DMAMUX) in which this request can be multiplexed, +and the 2nd specifies the request source. + +Examples: + +sai2: sai@40031000 { + compatible = "fsl,vf610-sai"; + reg = <0x40031000 0x1000>; + interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "sai"; + clocks = <&clks VF610_CLK_SAI2>; + dma-names = "tx", "rx"; + dmas = <&edma0 0 21>, + <&edma0 0 20>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt index 68b83ecc3850..4659fd952301 100644 --- a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt +++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt @@ -1,12 +1,16 @@ * Freescale Smart Direct Memory Access (SDMA) Controller for i.MX Required properties: -- compatible : Should be "fsl,imx31-sdma", "fsl,imx31-to1-sdma", - "fsl,imx31-to2-sdma", "fsl,imx35-sdma", "fsl,imx35-to1-sdma", - "fsl,imx35-to2-sdma", "fsl,imx51-sdma", "fsl,imx53-sdma" or - "fsl,imx6q-sdma". The -to variants should be preferred since they - allow to determnine the correct ROM script addresses needed for - the driver to work without additional firmware. +- compatible : Should be one of + "fsl,imx25-sdma" + "fsl,imx31-sdma", "fsl,imx31-to1-sdma", "fsl,imx31-to2-sdma" + "fsl,imx35-sdma", "fsl,imx35-to1-sdma", "fsl,imx35-to2-sdma" + "fsl,imx51-sdma" + "fsl,imx53-sdma" + "fsl,imx6q-sdma" + The -to variants should be preferred since they allow to determine the + correct ROM script addresses needed for the driver to work without additional + firmware. - reg : Should contain SDMA registers location and length - interrupts : Should contain SDMA interrupt - #dma-cells : Must be <3>. @@ -43,6 +47,7 @@ The full ID of peripheral types can be found below. 20 ASRC 21 ESAI 22 SSI Dual FIFO (needs firmware ver >= 2) + 23 Shared ASRC The third cell specifies the transfer priority as below. diff --git a/Documentation/devicetree/bindings/dma/mmp-dma.txt b/Documentation/devicetree/bindings/dma/mmp-dma.txt index a4fa4efa1d83..7a802f64e5bd 100644 --- a/Documentation/devicetree/bindings/dma/mmp-dma.txt +++ b/Documentation/devicetree/bindings/dma/mmp-dma.txt @@ -1,17 +1,20 @@ * MARVELL MMP DMA controller Marvell Peripheral DMA Controller -Used platfroms: pxa688, pxa910, pxa3xx, etc +Used platforms: pxa688, pxa910, pxa3xx, etc Required properties: - compatible: Should be "marvell,pdma-1.0" - reg: Should contain DMA registers location and length. - interrupts: Either contain all of the per-channel DMA interrupts or one irq for pdma device -- #dma-channels: Number of DMA channels supported by the controller. + +Optional properties: +- #dma-channels: Number of DMA channels supported by the controller (defaults + to 32 when not specified) "marvell,pdma-1.0" -Used platfroms: pxa25x, pxa27x, pxa3xx, pxa93x, pxa168, pxa910, pxa688. +Used platforms: pxa25x, pxa27x, pxa3xx, pxa93x, pxa168, pxa910, pxa688. Examples: @@ -45,7 +48,7 @@ pdma: dma-controller@d4000000 { Marvell Two Channel DMA Controller used specifically for audio -Used platfroms: pxa688, pxa910 +Used platforms: pxa688, pxa910 Required properties: - compatible: Should be "marvell,adma-1.0" or "marvell,pxa910-squ" diff --git a/Documentation/devicetree/bindings/dma/mpc512x-dma.txt b/Documentation/devicetree/bindings/dma/mpc512x-dma.txt new file mode 100644 index 000000000000..a6511df165c5 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/mpc512x-dma.txt @@ -0,0 +1,29 @@ +* Freescale MPC512x and MPC8308 DMA Controller + +The DMA controller in Freescale MPC512x and MPC8308 SoCs can move +blocks of memory contents between memory and peripherals or +from memory to memory. + +Refer to "Generic DMA Controller and DMA request bindings" in +the dma/dma.txt file for a more detailed description of binding. + +Required properties: +- compatible: should be "fsl,mpc5121-dma" or "fsl,mpc8308-dma"; +- reg: should contain the DMA controller registers location and length; +- interrupt for the DMA controller: syntax of interrupt client node + is described in interrupt-controller/interrupts.txt file. +- #dma-cells: the length of the DMA specifier, must be <1>. + Each channel of this DMA controller has a peripheral request line, + the assignment is fixed in hardware. This one cell + in dmas property of a client device represents the channel number. + +Example: + + dma0: dma@14000 { + compatible = "fsl,mpc5121-dma"; + reg = <0x14000 0x1800>; + interrupts = <65 0x8>; + #dma-cells = <1>; + }; + +DMA clients must use the format described in dma/dma.txt file. diff --git a/Documentation/devicetree/bindings/dma/nbpfaxi.txt b/Documentation/devicetree/bindings/dma/nbpfaxi.txt new file mode 100644 index 000000000000..d5e2522b9ec1 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/nbpfaxi.txt @@ -0,0 +1,61 @@ +* Renesas "Type-AXI" NBPFAXI* DMA controllers + +* DMA controller + +Required properties + +- compatible: must be one of + "renesas,nbpfaxi64dmac1b4" + "renesas,nbpfaxi64dmac1b8" + "renesas,nbpfaxi64dmac1b16" + "renesas,nbpfaxi64dmac4b4" + "renesas,nbpfaxi64dmac4b8" + "renesas,nbpfaxi64dmac4b16" + "renesas,nbpfaxi64dmac8b4" + "renesas,nbpfaxi64dmac8b8" + "renesas,nbpfaxi64dmac8b16" +- #dma-cells: must be 2: the first integer is a terminal number, to which this + slave is connected, the second one is flags. Flags is a bitmask + with the following bits defined: + +#define NBPF_SLAVE_RQ_HIGH 1 +#define NBPF_SLAVE_RQ_LOW 2 +#define NBPF_SLAVE_RQ_LEVEL 4 + +Optional properties: + +You can use dma-channels and dma-requests as described in dma.txt, although they +won't be used, this information is derived from the compatibility string. + +Example: + + dma: dma-controller@48000000 { + compatible = "renesas,nbpfaxi64dmac8b4"; + reg = <0x48000000 0x400>; + interrupts = <0 12 0x4 + 0 13 0x4 + 0 14 0x4 + 0 15 0x4 + 0 16 0x4 + 0 17 0x4 + 0 18 0x4 + 0 19 0x4>; + #dma-cells = <2>; + dma-channels = <8>; + dma-requests = <8>; + }; + +* DMA client + +Required properties: + +dmas and dma-names are required, as described in dma.txt. + +Example: + +#include <dt-bindings/dma/nbpfaxi.h> + +... + dmas = <&dma 0 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL) + &dma 1 (NBPF_SLAVE_RQ_HIGH | NBPF_SLAVE_RQ_LEVEL)>; + dma-names = "rx", "tx"; diff --git a/Documentation/devicetree/bindings/dma/qcom_adm.txt b/Documentation/devicetree/bindings/dma/qcom_adm.txt new file mode 100644 index 000000000000..9bcab9115982 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/qcom_adm.txt @@ -0,0 +1,62 @@ +QCOM ADM DMA Controller + +Required properties: +- compatible: must contain "qcom,adm" for IPQ/APQ8064 and MSM8960 +- reg: Address range for DMA registers +- interrupts: Should contain one interrupt shared by all channels +- #dma-cells: must be <2>. First cell denotes the channel number. Second cell + denotes CRCI (client rate control interface) flow control assignment. +- clocks: Should contain the core clock and interface clock. +- clock-names: Must contain "core" for the core clock and "iface" for the + interface clock. +- resets: Must contain an entry for each entry in reset names. +- reset-names: Must include the following entries: + - clk + - c0 + - c1 + - c2 +- qcom,ee: indicates the security domain identifier used in the secure world. + +Example: + adm_dma: dma@18300000 { + compatible = "qcom,adm"; + reg = <0x18300000 0x100000>; + interrupts = <0 170 0>; + #dma-cells = <2>; + + clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>; + clock-names = "core", "iface"; + + resets = <&gcc ADM0_RESET>, + <&gcc ADM0_C0_RESET>, + <&gcc ADM0_C1_RESET>, + <&gcc ADM0_C2_RESET>; + reset-names = "clk", "c0", "c1", "c2"; + qcom,ee = <0>; + }; + +DMA clients must use the format descripted in the dma.txt file, using a three +cell specifier for each channel. + +Each dmas request consists of 3 cells: + 1. phandle pointing to the DMA controller + 2. channel number + 3. CRCI assignment, if applicable. If no CRCI flow control is required, use 0. + The CRCI is used for flow control. It identifies the peripheral device that + is the source/destination for the transferred data. + +Example: + + spi4: spi@1a280000 { + status = "ok"; + spi-max-frequency = <50000000>; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 0>; + + dmas = <&adm_dma 6 9>, + <&adm_dma 5 10>; + dma-names = "rx", "tx"; + }; diff --git a/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt b/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt new file mode 100644 index 000000000000..d75a9d767022 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt @@ -0,0 +1,41 @@ +QCOM BAM DMA controller + +Required properties: +- compatible: must contain "qcom,bam-v1.4.0" for MSM8974 +- reg: Address range for DMA registers +- interrupts: Should contain the one interrupt shared by all channels +- #dma-cells: must be <1>, the cell in the dmas property of the client device + represents the channel number +- clocks: required clock +- clock-names: must contain "bam_clk" entry +- qcom,ee : indicates the active Execution Environment identifier (0-7) used in + the secure world. + +Example: + + uart-bam: dma@f9984000 = { + compatible = "qcom,bam-v1.4.0"; + reg = <0xf9984000 0x15000>; + interrupts = <0 94 0>; + clocks = <&gcc GCC_BAM_DMA_AHB_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + }; + +DMA clients must use the format described in the dma.txt file, using a two cell +specifier for each channel. + +Example: + serial@f991e000 { + compatible = "qcom,msm-uart"; + reg = <0xf991e000 0x1000> + <0xf9944000 0x19000>; + interrupts = <0 108 0>; + clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + + dmas = <&uart-bam 0>, <&uart-bam 1>; + dma-names = "rx", "tx"; + }; diff --git a/Documentation/devicetree/bindings/dma/rcar-audmapp.txt b/Documentation/devicetree/bindings/dma/rcar-audmapp.txt new file mode 100644 index 000000000000..61bca509d7b9 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/rcar-audmapp.txt @@ -0,0 +1,29 @@ +* R-Car Audio DMAC peri peri Device Tree bindings + +Required properties: +- compatible: should be "renesas,rcar-audmapp" +- #dma-cells: should be <1>, see "dmas" property below + +Example: + audmapp: audio-dma-pp@0xec740000 { + compatible = "renesas,rcar-audmapp"; + #dma-cells = <1>; + + reg = <0 0xec740000 0 0x200>; + }; + + +* DMA client + +Required properties: +- dmas: a list of <[DMA multiplexer phandle] [SRS << 8 | DRS]> pairs. + where SRS/DRS are specified in the SoC manual. + It will be written into PDMACHCR as high 16-bit parts. +- dma-names: a list of DMA channel names, one per "dmas" entry + +Example: + + dmas = <&audmapp 0x2d00 + &audmapp 0x3700>; + dma-names = "src0_ssiu0", + "dvc0_ssiu0"; diff --git a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt new file mode 100644 index 000000000000..df0f48bcf75a --- /dev/null +++ b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt @@ -0,0 +1,98 @@ +* Renesas R-Car DMA Controller Device Tree bindings + +Renesas R-Car Generation 2 SoCs have have multiple multi-channel DMA +controller instances named DMAC capable of serving multiple clients. Channels +can be dedicated to specific clients or shared between a large number of +clients. + +DMA clients are connected to the DMAC ports referenced by an 8-bit identifier +called MID/RID. + +Each DMA client is connected to one dedicated port of the DMAC, identified by +an 8-bit port number called the MID/RID. A DMA controller can thus serve up to +256 clients in total. When the number of hardware channels is lower than the +number of clients to be served, channels must be shared between multiple DMA +clients. The association of DMA clients to DMAC channels is fully dynamic and +not described in these device tree bindings. + +Required Properties: + +- compatible: must contain "renesas,rcar-dmac" + +- reg: base address and length of the registers block for the DMAC + +- interrupts: interrupt specifiers for the DMAC, one for each entry in + interrupt-names. +- interrupt-names: one entry per channel, named "ch%u", where %u is the + channel number ranging from zero to the number of channels minus one. + +- clock-names: "fck" for the functional clock +- clocks: a list of phandle + clock-specifier pairs, one for each entry + in clock-names. +- clock-names: must contain "fck" for the functional clock. + +- #dma-cells: must be <1>, the cell specifies the MID/RID of the DMAC port + connected to the DMA client +- dma-channels: number of DMA channels + +Example: R8A7790 (R-Car H2) SYS-DMACs + + dmac0: dma-controller@e6700000 { + compatible = "renesas,rcar-dmac"; + reg = <0 0xe6700000 0 0x20000>; + interrupts = <0 197 IRQ_TYPE_LEVEL_HIGH + 0 200 IRQ_TYPE_LEVEL_HIGH + 0 201 IRQ_TYPE_LEVEL_HIGH + 0 202 IRQ_TYPE_LEVEL_HIGH + 0 203 IRQ_TYPE_LEVEL_HIGH + 0 204 IRQ_TYPE_LEVEL_HIGH + 0 205 IRQ_TYPE_LEVEL_HIGH + 0 206 IRQ_TYPE_LEVEL_HIGH + 0 207 IRQ_TYPE_LEVEL_HIGH + 0 208 IRQ_TYPE_LEVEL_HIGH + 0 209 IRQ_TYPE_LEVEL_HIGH + 0 210 IRQ_TYPE_LEVEL_HIGH + 0 211 IRQ_TYPE_LEVEL_HIGH + 0 212 IRQ_TYPE_LEVEL_HIGH + 0 213 IRQ_TYPE_LEVEL_HIGH + 0 214 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", + "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14"; + clocks = <&mstp2_clks R8A7790_CLK_SYS_DMAC0>; + clock-names = "fck"; + #dma-cells = <1>; + dma-channels = <15>; + }; + + dmac1: dma-controller@e6720000 { + compatible = "renesas,rcar-dmac"; + reg = <0 0xe6720000 0 0x20000>; + interrupts = <0 220 IRQ_TYPE_LEVEL_HIGH + 0 216 IRQ_TYPE_LEVEL_HIGH + 0 217 IRQ_TYPE_LEVEL_HIGH + 0 218 IRQ_TYPE_LEVEL_HIGH + 0 219 IRQ_TYPE_LEVEL_HIGH + 0 308 IRQ_TYPE_LEVEL_HIGH + 0 309 IRQ_TYPE_LEVEL_HIGH + 0 310 IRQ_TYPE_LEVEL_HIGH + 0 311 IRQ_TYPE_LEVEL_HIGH + 0 312 IRQ_TYPE_LEVEL_HIGH + 0 313 IRQ_TYPE_LEVEL_HIGH + 0 314 IRQ_TYPE_LEVEL_HIGH + 0 315 IRQ_TYPE_LEVEL_HIGH + 0 316 IRQ_TYPE_LEVEL_HIGH + 0 317 IRQ_TYPE_LEVEL_HIGH + 0 318 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", + "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14"; + clocks = <&mstp2_clks R8A7790_CLK_SYS_DMAC1>; + clock-names = "fck"; + #dma-cells = <1>; + dma-channels = <15>; + }; diff --git a/Documentation/devicetree/bindings/dma/sirfsoc-dma.txt b/Documentation/devicetree/bindings/dma/sirfsoc-dma.txt new file mode 100644 index 000000000000..ecbc96ad36f8 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/sirfsoc-dma.txt @@ -0,0 +1,43 @@ +* CSR SiRFSoC DMA controller + +See dma.txt first + +Required properties: +- compatible: Should be "sirf,prima2-dmac" or "sirf,marco-dmac" +- reg: Should contain DMA registers location and length. +- interrupts: Should contain one interrupt shared by all channel +- #dma-cells: must be <1>. used to represent the number of integer + cells in the dmas property of client device. +- clocks: clock required + +Example: + +Controller: +dmac0: dma-controller@b00b0000 { + compatible = "sirf,prima2-dmac"; + reg = <0xb00b0000 0x10000>; + interrupts = <12>; + clocks = <&clks 24>; + #dma-cells = <1>; +}; + + +Client: +Fill the specific dma request line in dmas. In the below example, spi0 read +channel request line is 9 of the 2nd dma controller, while write channel uses +4 of the 2nd dma controller; spi1 read channel request line is 12 of the 1st +dma controller, while write channel uses 13 of the 1st dma controller: + +spi0: spi@b00d0000 { + compatible = "sirf,prima2-spi"; + dmas = <&dmac1 9>, + <&dmac1 4>; + dma-names = "rx", "tx"; +}; + +spi1: spi@b0170000 { + compatible = "sirf,prima2-spi"; + dmas = <&dmac0 12>, + <&dmac0 13>; + dma-names = "rx", "tx"; +}; diff --git a/Documentation/devicetree/bindings/dma/ste-dma40.txt b/Documentation/devicetree/bindings/dma/ste-dma40.txt index 1f5729f10621..95800ab37bb0 100644 --- a/Documentation/devicetree/bindings/dma/ste-dma40.txt +++ b/Documentation/devicetree/bindings/dma/ste-dma40.txt @@ -35,9 +35,11 @@ Required properties: Each dmas request consists of 4 cells: 1. A phandle pointing to the DMA controller - 2. Device Type + 2. Device signal number, the signal line for single and burst requests + connected from the device to the DMA40 engine 3. The DMA request line number (only when 'use fixed channel' is set) - 4. A 32bit mask specifying; mode, direction and endianness [NB: This list will grow] + 4. A 32bit mask specifying; mode, direction and endianness + [NB: This list will grow] 0x00000001: Mode: Logical channel when unset Physical channel when set @@ -54,6 +56,74 @@ Each dmas request consists of 4 cells: Normal priority when unset High priority when set +Existing signal numbers for the DB8500 ASIC. Unless specified, the signals are +bidirectional, i.e. the same for RX and TX operations: + +0: SPI controller 0 +1: SD/MMC controller 0 (unused) +2: SD/MMC controller 1 (unused) +3: SD/MMC controller 2 (unused) +4: I2C port 1 +5: I2C port 3 +6: I2C port 2 +7: I2C port 4 +8: Synchronous Serial Port SSP0 +9: Synchronous Serial Port SSP1 +10: Multi-Channel Display Engine MCDE RX +11: UART port 2 +12: UART port 1 +13: UART port 0 +14: Multirate Serial Port MSP2 +15: I2C port 0 +16: USB OTG in/out endpoints 7 & 15 +17: USB OTG in/out endpoints 6 & 14 +18: USB OTG in/out endpoints 5 & 13 +19: USB OTG in/out endpoints 4 & 12 +20: SLIMbus or HSI channel 0 +21: SLIMbus or HSI channel 1 +22: SLIMbus or HSI channel 2 +23: SLIMbus or HSI channel 3 +24: Multimedia DSP SXA0 +25: Multimedia DSP SXA1 +26: Multimedia DSP SXA2 +27: Multimedia DSP SXA3 +28: SD/MM controller 2 +29: SD/MM controller 0 +30: MSP port 1 on DB8500 v1, MSP port 3 on DB8500 v2 +31: MSP port 0 or SLIMbus channel 0 +32: SD/MM controller 1 +33: SPI controller 2 +34: i2c3 RX2 TX2 +35: SPI controller 1 +36: USB OTG in/out endpoints 3 & 11 +37: USB OTG in/out endpoints 2 & 10 +38: USB OTG in/out endpoints 1 & 9 +39: USB OTG in/out endpoints 8 +40: SPI controller 3 +41: SD/MM controller 3 +42: SD/MM controller 4 +43: SD/MM controller 5 +44: Multimedia DSP SXA4 +45: Multimedia DSP SXA5 +46: SLIMbus channel 8 or Multimedia DSP SXA6 +47: SLIMbus channel 9 or Multimedia DSP SXA7 +48: Crypto Accelerator 1 +49: Crypto Accelerator 1 TX or Hash Accelerator 1 TX +50: Hash Accelerator 1 TX +51: memcpy TX (to be used by the DMA driver for memcpy operations) +52: SLIMbus or HSI channel 4 +53: SLIMbus or HSI channel 5 +54: SLIMbus or HSI channel 6 +55: SLIMbus or HSI channel 7 +56: memcpy (to be used by the DMA driver for memcpy operations) +57: memcpy (to be used by the DMA driver for memcpy operations) +58: memcpy (to be used by the DMA driver for memcpy operations) +59: memcpy (to be used by the DMA driver for memcpy operations) +60: memcpy (to be used by the DMA driver for memcpy operations) +61: Crypto Accelerator 0 +62: Crypto Accelerator 0 TX or Hash Accelerator 0 TX +63: Hash Accelerator 0 TX + Example: uart@80120000 { diff --git a/Documentation/devicetree/bindings/dma/sun6i-dma.txt b/Documentation/devicetree/bindings/dma/sun6i-dma.txt new file mode 100644 index 000000000000..3e145c1675b1 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/sun6i-dma.txt @@ -0,0 +1,45 @@ +Allwinner A31 DMA Controller + +This driver follows the generic DMA bindings defined in dma.txt. + +Required properties: + +- compatible: Must be "allwinner,sun6i-a31-dma" +- reg: Should contain the registers base address and length +- interrupts: Should contain a reference to the interrupt used by this device +- clocks: Should contain a reference to the parent AHB clock +- resets: Should contain a reference to the reset controller asserting + this device in reset +- #dma-cells : Should be 1, a single cell holding a line request number + +Example: + dma: dma-controller@01c02000 { + compatible = "allwinner,sun6i-a31-dma"; + reg = <0x01c02000 0x1000>; + interrupts = <0 50 4>; + clocks = <&ahb1_gates 6>; + resets = <&ahb1_rst 6>; + #dma-cells = <1>; + }; + +Clients: + +DMA clients connected to the A31 DMA controller must use the format +described in the dma.txt file, using a two-cell specifier for each +channel: a phandle plus one integer cells. +The two cells in order are: + +1. A phandle pointing to the DMA controller. +2. The port ID as specified in the datasheet + +Example: +spi2: spi@01c6a000 { + compatible = "allwinner,sun6i-a31-spi"; + reg = <0x01c6a000 0x1000>; + interrupts = <0 67 4>; + clocks = <&ahb1_gates 22>, <&spi2_clk>; + clock-names = "ahb", "mod"; + dmas = <&dma 25>, <&dma 25>; + dma-names = "rx", "tx"; + resets = <&ahb1_rst 22>; +}; diff --git a/Documentation/devicetree/bindings/dma/ti-edma.txt b/Documentation/devicetree/bindings/dma/ti-edma.txt index 9fbbdb783a72..5ba525a10035 100644 --- a/Documentation/devicetree/bindings/dma/ti-edma.txt +++ b/Documentation/devicetree/bindings/dma/ti-edma.txt @@ -2,11 +2,8 @@ TI EDMA Required properties: - compatible : "ti,edma3" -- ti,edma-regions: Number of regions -- ti,edma-slots: Number of slots - #dma-cells: Should be set to <1> Clients should use a single channel number per DMA request. -- dma-channels: Specify total DMA channels per CC - reg: Memory map for accessing module - interrupt-parent: Interrupt controller the interrupt is routed through - interrupts: Exactly 3 interrupts need to be specified in the order: @@ -17,6 +14,13 @@ Optional properties: - ti,hwmods: Name of the hwmods associated to the EDMA - ti,edma-xbar-event-map: Crossbar event to channel map +Deprecated properties: +Listed here in case one wants to boot an old kernel with new DTB. These +properties might need to be added to the new DTS files. +- ti,edma-regions: Number of regions +- ti,edma-slots: Number of slots +- dma-channels: Specify total DMA channels per CC + Example: edma: edma@49000000 { @@ -26,9 +30,6 @@ edma: edma@49000000 { compatible = "ti,edma3"; ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2"; #dma-cells = <1>; - dma-channels = <64>; - ti,edma-regions = <4>; - ti,edma-slots = <256>; - ti,edma-xbar-event-map = <1 12 - 2 13>; + ti,edma-xbar-event-map = /bits/ 16 <1 12 + 2 13>; }; diff --git a/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt b/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt new file mode 100644 index 000000000000..2291c4098730 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt @@ -0,0 +1,65 @@ +Xilinx AXI DMA engine, it does transfers between memory and AXI4 stream +target devices. It can be configured to have one channel or two channels. +If configured as two channels, one is to transmit to the device and another +is to receive from the device. + +Required properties: +- compatible: Should be "xlnx,axi-dma-1.00.a" +- #dma-cells: Should be <1>, see "dmas" property below +- reg: Should contain DMA registers location and length. +- dma-channel child node: Should have atleast one channel and can have upto + two channels per device. This node specifies the properties of each + DMA channel (see child node properties below). + +Optional properties: +- xlnx,include-sg: Tells whether configured for Scatter-mode in + the hardware. + +Required child node properties: +- compatible: It should be either "xlnx,axi-dma-mm2s-channel" or + "xlnx,axi-dma-s2mm-channel". +- interrupts: Should contain per channel DMA interrupts. +- xlnx,datawidth: Should contain the stream data width, take values + {32,64...1024}. + +Option child node properties: +- xlnx,include-dre: Tells whether hardware is configured for Data + Realignment Engine. + +Example: +++++++++ + +axi_dma_0: axidma@40400000 { + compatible = "xlnx,axi-dma-1.00.a"; + #dma_cells = <1>; + reg = < 0x40400000 0x10000 >; + dma-channel@40400000 { + compatible = "xlnx,axi-dma-mm2s-channel"; + interrupts = < 0 59 4 >; + xlnx,datawidth = <0x40>; + } ; + dma-channel@40400030 { + compatible = "xlnx,axi-dma-s2mm-channel"; + interrupts = < 0 58 4 >; + xlnx,datawidth = <0x40>; + } ; +} ; + + +* DMA client + +Required properties: +- dmas: a list of <[DMA device phandle] [Channel ID]> pairs, + where Channel ID is '0' for write/tx and '1' for read/rx + channel. +- dma-names: a list of DMA channel names, one per "dmas" entry + +Example: +++++++++ + +dmatest_0: dmatest@0 { + compatible ="xlnx,axi-dma-test-1.00.a"; + dmas = <&axi_dma_0 0 + &axi_dma_0 1>; + dma-names = "dma0", "dma1"; +} ; diff --git a/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt b/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt new file mode 100644 index 000000000000..e4c4d47f8137 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt @@ -0,0 +1,75 @@ +Xilinx AXI VDMA engine, it does transfers between memory and video devices. +It can be configured to have one channel or two channels. If configured +as two channels, one is to transmit to the video device and another is +to receive from the video device. + +Required properties: +- compatible: Should be "xlnx,axi-vdma-1.00.a" +- #dma-cells: Should be <1>, see "dmas" property below +- reg: Should contain VDMA registers location and length. +- xlnx,num-fstores: Should be the number of framebuffers as configured in h/w. +- dma-channel child node: Should have at least one channel and can have up to + two channels per device. This node specifies the properties of each + DMA channel (see child node properties below). + +Optional properties: +- xlnx,include-sg: Tells configured for Scatter-mode in + the hardware. +- xlnx,flush-fsync: Tells which channel to Flush on Frame sync. + It takes following values: + {1}, flush both channels + {2}, flush mm2s channel + {3}, flush s2mm channel + +Required child node properties: +- compatible: It should be either "xlnx,axi-vdma-mm2s-channel" or + "xlnx,axi-vdma-s2mm-channel". +- interrupts: Should contain per channel VDMA interrupts. +- xlnx,datawidth: Should contain the stream data width, take values + {32,64...1024}. + +Optional child node properties: +- xlnx,include-dre: Tells hardware is configured for Data + Realignment Engine. +- xlnx,genlock-mode: Tells Genlock synchronization is + enabled/disabled in hardware. + +Example: +++++++++ + +axi_vdma_0: axivdma@40030000 { + compatible = "xlnx,axi-vdma-1.00.a"; + #dma_cells = <1>; + reg = < 0x40030000 0x10000 >; + xlnx,num-fstores = <0x8>; + xlnx,flush-fsync = <0x1>; + dma-channel@40030000 { + compatible = "xlnx,axi-vdma-mm2s-channel"; + interrupts = < 0 54 4 >; + xlnx,datawidth = <0x40>; + } ; + dma-channel@40030030 { + compatible = "xlnx,axi-vdma-s2mm-channel"; + interrupts = < 0 53 4 >; + xlnx,datawidth = <0x40>; + } ; +} ; + + +* DMA client + +Required properties: +- dmas: a list of <[Video DMA device phandle] [Channel ID]> pairs, + where Channel ID is '0' for write/tx and '1' for read/rx + channel. +- dma-names: a list of DMA channel names, one per "dmas" entry + +Example: +++++++++ + +vdmatest_0: vdmatest@0 { + compatible ="xlnx,axi-vdma-test-1.00.a"; + dmas = <&axi_vdma_0 0 + &axi_vdma_0 1>; + dma-names = "vdma0", "vdma1"; +} ; diff --git a/Documentation/devicetree/bindings/drm/armada/marvell,dove-lcd.txt b/Documentation/devicetree/bindings/drm/armada/marvell,dove-lcd.txt new file mode 100644 index 000000000000..46525ea3e646 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/armada/marvell,dove-lcd.txt @@ -0,0 +1,30 @@ +Device Tree bindings for Armada DRM CRTC driver + +Required properties: + - compatible: value should be "marvell,dove-lcd". + - reg: base address and size of the LCD controller + - interrupts: single interrupt number for the LCD controller + - port: video output port with endpoints, as described by graph.txt + +Optional properties: + + - clocks: as described by clock-bindings.txt + - clock-names: as described by clock-bindings.txt + "axiclk" - axi bus clock for pixel clock + "plldivider" - pll divider clock for pixel clock + "ext_ref_clk0" - external clock 0 for pixel clock + "ext_ref_clk1" - external clock 1 for pixel clock + +Note: all clocks are optional but at least one must be specified. +Further clocks may be added in the future according to requirements of +different SoCs. + +Example: + + lcd0: lcd-controller@820000 { + compatible = "marvell,dove-lcd"; + reg = <0x820000 0x1000>; + interrupts = <47>; + clocks = <&si5351 0>; + clock-names = "ext_ref_clk_1"; + }; diff --git a/Documentation/devicetree/bindings/drm/bridge/ptn3460.txt b/Documentation/devicetree/bindings/drm/bridge/ptn3460.txt new file mode 100644 index 000000000000..52b93b2c6748 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/bridge/ptn3460.txt @@ -0,0 +1,27 @@ +ptn3460 bridge bindings + +Required properties: + - compatible: "nxp,ptn3460" + - reg: i2c address of the bridge + - powerdown-gpio: OF device-tree gpio specification + - reset-gpio: OF device-tree gpio specification + - edid-emulation: The EDID emulation entry to use + +-------+------------+------------------+ + | Value | Resolution | Description | + | 0 | 1024x768 | NXP Generic | + | 1 | 1920x1080 | NXP Generic | + | 2 | 1920x1080 | NXP Generic | + | 3 | 1600x900 | Samsung LTM200KT | + | 4 | 1920x1080 | Samsung LTM230HT | + | 5 | 1366x768 | NXP Generic | + | 6 | 1600x900 | ChiMei M215HGE | + +-------+------------+------------------+ + +Example: + lvds-bridge@20 { + compatible = "nxp,ptn3460"; + reg = <0x20>; + powerdown-gpio = <&gpy2 5 1 0 0>; + reset-gpio = <&gpx1 5 1 0 0>; + edid-emulation = <5>; + }; diff --git a/Documentation/devicetree/bindings/drm/i2c/tda998x.txt b/Documentation/devicetree/bindings/drm/i2c/tda998x.txt new file mode 100644 index 000000000000..e9e4bce40760 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/i2c/tda998x.txt @@ -0,0 +1,29 @@ +Device-Tree bindings for the NXP TDA998x HDMI transmitter + +Required properties; + - compatible: must be "nxp,tda998x" + + - reg: I2C address + +Optional properties: + - interrupts: interrupt number and trigger type + default: polling + + - pinctrl-0: pin control group to be used for + screen plug/unplug interrupt. + + - pinctrl-names: must contain a "default" entry. + + - video-ports: 24 bits value which defines how the video controller + output is wired to the TDA998x input - default: <0x230145> + +Example: + + tda998x: hdmi-encoder { + compatible = "nxp,tda998x"; + reg = <0x70>; + interrupt-parent = <&gpio0>; + interrupts = <27 2>; /* falling edge */ + pinctrl-0 = <&pmx_camera>; + pinctrl-names = "default"; + }; diff --git a/Documentation/devicetree/bindings/drm/msm/gpu.txt b/Documentation/devicetree/bindings/drm/msm/gpu.txt new file mode 100644 index 000000000000..67d0a58dbb77 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/msm/gpu.txt @@ -0,0 +1,52 @@ +Qualcomm adreno/snapdragon GPU + +Required properties: +- compatible: "qcom,adreno-3xx" +- reg: Physical base address and length of the controller's registers. +- interrupts: The interrupt signal from the gpu. +- clocks: device clocks + See ../clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required: + * "core_clk" + * "iface_clk" + * "mem_iface_clk" +- qcom,chipid: gpu chip-id. Note this may become optional for future + devices if we can reliably read the chipid from hw +- qcom,gpu-pwrlevels: list of operating points + - compatible: "qcom,gpu-pwrlevels" + - for each qcom,gpu-pwrlevel: + - qcom,gpu-freq: requested gpu clock speed + - NOTE: downstream android driver defines additional parameters to + configure memory bandwidth scaling per OPP. + +Example: + +/ { + ... + + gpu: qcom,kgsl-3d0@4300000 { + compatible = "qcom,adreno-3xx"; + reg = <0x04300000 0x20000>; + reg-names = "kgsl_3d0_reg_memory"; + interrupts = <GIC_SPI 80 0>; + interrupt-names = "kgsl_3d0_irq"; + clock-names = + "core_clk", + "iface_clk", + "mem_iface_clk"; + clocks = + <&mmcc GFX3D_CLK>, + <&mmcc GFX3D_AHB_CLK>, + <&mmcc MMSS_IMEM_AHB_CLK>; + qcom,chipid = <0x03020100>; + qcom,gpu-pwrlevels { + compatible = "qcom,gpu-pwrlevels"; + qcom,gpu-pwrlevel@0 { + qcom,gpu-freq = <450000000>; + }; + qcom,gpu-pwrlevel@1 { + qcom,gpu-freq = <27000000>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/drm/msm/hdmi.txt b/Documentation/devicetree/bindings/drm/msm/hdmi.txt new file mode 100644 index 000000000000..aca917fe2ba7 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/msm/hdmi.txt @@ -0,0 +1,46 @@ +Qualcomm adreno/snapdragon hdmi output + +Required properties: +- compatible: one of the following + * "qcom,hdmi-tx-8660" + * "qcom,hdmi-tx-8960" +- reg: Physical base address and length of the controller's registers +- reg-names: "core_physical" +- interrupts: The interrupt signal from the hdmi block. +- clocks: device clocks + See ../clocks/clock-bindings.txt for details. +- qcom,hdmi-tx-ddc-clk-gpio: ddc clk pin +- qcom,hdmi-tx-ddc-data-gpio: ddc data pin +- qcom,hdmi-tx-hpd-gpio: hpd pin +- core-vdda-supply: phandle to supply regulator +- hdmi-mux-supply: phandle to mux regulator + +Optional properties: +- qcom,hdmi-tx-mux-en-gpio: hdmi mux enable pin +- qcom,hdmi-tx-mux-sel-gpio: hdmi mux select pin + +Example: + +/ { + ... + + hdmi: qcom,hdmi-tx-8960@4a00000 { + compatible = "qcom,hdmi-tx-8960"; + reg-names = "core_physical"; + reg = <0x04a00000 0x1000>; + interrupts = <GIC_SPI 79 0>; + clock-names = + "core_clk", + "master_iface_clk", + "slave_iface_clk"; + clocks = + <&mmcc HDMI_APP_CLK>, + <&mmcc HDMI_M_AHB_CLK>, + <&mmcc HDMI_S_AHB_CLK>; + qcom,hdmi-tx-ddc-clk = <&msmgpio 70 GPIO_ACTIVE_HIGH>; + qcom,hdmi-tx-ddc-data = <&msmgpio 71 GPIO_ACTIVE_HIGH>; + qcom,hdmi-tx-hpd = <&msmgpio 72 GPIO_ACTIVE_HIGH>; + core-vdda-supply = <&pm8921_hdmi_mvs>; + hdmi-mux-supply = <&ext_3p3v>; + }; +}; diff --git a/Documentation/devicetree/bindings/drm/msm/mdp.txt b/Documentation/devicetree/bindings/drm/msm/mdp.txt new file mode 100644 index 000000000000..1a0598e5279d --- /dev/null +++ b/Documentation/devicetree/bindings/drm/msm/mdp.txt @@ -0,0 +1,48 @@ +Qualcomm adreno/snapdragon display controller + +Required properties: +- compatible: + * "qcom,mdp" - mdp4 +- reg: Physical base address and length of the controller's registers. +- interrupts: The interrupt signal from the display controller. +- connectors: array of phandles for output device(s) +- clocks: device clocks + See ../clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required: + * "core_clk" + * "iface_clk" + * "lut_clk" + * "src_clk" + * "hdmi_clk" + * "mpd_clk" + +Optional properties: +- gpus: phandle for gpu device + +Example: + +/ { + ... + + mdp: qcom,mdp@5100000 { + compatible = "qcom,mdp"; + reg = <0x05100000 0xf0000>; + interrupts = <GIC_SPI 75 0>; + connectors = <&hdmi>; + gpus = <&gpu>; + clock-names = + "core_clk", + "iface_clk", + "lut_clk", + "src_clk", + "hdmi_clk", + "mdp_clk"; + clocks = + <&mmcc MDP_SRC>, + <&mmcc MDP_AHB_CLK>, + <&mmcc MDP_LUT_CLK>, + <&mmcc TV_SRC>, + <&mmcc HDMI_TV_CLK>, + <&mmcc MDP_TV_CLK>; + }; +}; diff --git a/Documentation/devicetree/bindings/drm/tilcdc/panel.txt b/Documentation/devicetree/bindings/drm/tilcdc/panel.txt index 9301c330d1a6..4ab9e2300907 100644 --- a/Documentation/devicetree/bindings/drm/tilcdc/panel.txt +++ b/Documentation/devicetree/bindings/drm/tilcdc/panel.txt @@ -18,6 +18,10 @@ Required properties: Documentation/devicetree/bindings/video/display-timing.txt for display timing binding details. +Optional properties: +- backlight: phandle of the backlight device attached to the panel +- enable-gpios: GPIO pin to enable or disable the panel + Recommended properties: - pinctrl-names, pinctrl-0: the pincontrol settings to configure muxing properly for pins that connect to TFP410 device @@ -29,6 +33,9 @@ Example: compatible = "ti,tilcdc,panel"; pinctrl-names = "default"; pinctrl-0 = <&bone_lcd3_cape_lcd_pins>; + backlight = <&backlight>; + enable-gpios = <&gpio3 19 0>; + panel-info { ac-bias = <255>; ac-bias-intrpt = <0>; diff --git a/Documentation/devicetree/bindings/extcon/extcon-rt8973a.txt b/Documentation/devicetree/bindings/extcon/extcon-rt8973a.txt new file mode 100644 index 000000000000..6dede7d11532 --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/extcon-rt8973a.txt @@ -0,0 +1,25 @@ + +* Richtek RT8973A - Micro USB Switch device + +The Richtek RT8973A is Micro USB Switch with OVP and I2C interface. The RT8973A +is a USB port accessory detector and switch that is optimized to protect low +voltage system from abnormal high input voltage (up to 28V) and supports high +speed USB operation. Also, RT8973A support 'auto-configuration' mode. +If auto-configuration mode is enabled, RT8973A would control internal h/w patch +for USB D-/D+ switching. + +Required properties: +- compatible: Should be "richtek,rt8973a-muic" +- reg: Specifies the I2C slave address of the MUIC block. It should be 0x14 +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from rt8973a are delivered to. +- interrupts: Interrupt specifiers for detection interrupt sources. + +Example: + + rt8973a@14 { + compatible = "richtek,rt8973a-muic"; + interrupt-parent = <&gpx1>; + interrupts = <5 0>; + reg = <0x14>; + }; diff --git a/Documentation/devicetree/bindings/extcon/extcon-sm5502.txt b/Documentation/devicetree/bindings/extcon/extcon-sm5502.txt new file mode 100644 index 000000000000..4ecda224955f --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/extcon-sm5502.txt @@ -0,0 +1,23 @@ + +* SM5502 MUIC (Micro-USB Interface Controller) device + +The Silicon Mitus SM5502 is a MUIC (Micro-USB Interface Controller) device +which can detect the state of external accessory when external accessory is +attached or detached and button is pressed or released. It is interfaced to +the host controller using an I2C interface. + +Required properties: +- compatible: Should be "siliconmitus,sm5502-muic" +- reg: Specifies the I2C slave address of the MUIC block. It should be 0x25 +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from sm5502 are delivered to. +- interrupts: Interrupt specifiers for detection interrupt sources. + +Example: + + sm5502@25 { + compatible = "siliconmitus,sm5502-muic"; + interrupt-parent = <&gpx1>; + interrupts = <5 0>; + reg = <0x25>; + }; diff --git a/Documentation/devicetree/bindings/fuse/nvidia,tegra20-fuse.txt b/Documentation/devicetree/bindings/fuse/nvidia,tegra20-fuse.txt new file mode 100644 index 000000000000..d8c98c7614d0 --- /dev/null +++ b/Documentation/devicetree/bindings/fuse/nvidia,tegra20-fuse.txt @@ -0,0 +1,40 @@ +NVIDIA Tegra20/Tegra30/Tegr114/Tegra124 fuse block. + +Required properties: +- compatible : should be: + "nvidia,tegra20-efuse" + "nvidia,tegra30-efuse" + "nvidia,tegra114-efuse" + "nvidia,tegra124-efuse" + Details: + nvidia,tegra20-efuse: Tegra20 requires using APB DMA to read the fuse data + due to a hardware bug. Tegra20 also lacks certain information which is + available in later generations such as fab code, lot code, wafer id,.. + nvidia,tegra30-efuse, nvidia,tegra114-efuse and nvidia,tegra124-efuse: + The differences between these SoCs are the size of the efuse array, + the location of the spare (OEM programmable) bits and the location of + the speedo data. +- reg: Should contain 1 entry: the entry gives the physical address and length + of the fuse registers. +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - fuse +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - fuse + +Example: + + fuse@7000f800 { + compatible = "nvidia,tegra20-efuse"; + reg = <0x7000F800 0x400>, + <0x70000000 0x400>; + clocks = <&tegra_car TEGRA20_CLK_FUSE>; + clock-names = "fuse"; + resets = <&tegra_car 39>; + reset-names = "fuse"; + }; + + diff --git a/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt b/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt new file mode 100644 index 000000000000..94ae9f82dcf8 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt @@ -0,0 +1,17 @@ +* ARM Cirrus Logic CLPS711X SYSFLG1 MCTRL GPIOs + +Required properties: +- compatible: Should contain "cirrus,clps711x-mctrl-gpio". +- gpio-controller: Marks the device node as a gpio controller. +- #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = Active high, + 1 = Active low. + +Example: + sysgpio: sysgpio { + compatible = "cirrus,ep7312-mctrl-gpio", + "cirrus,clps711x-mctrl-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-davinci.txt b/Documentation/devicetree/bindings/gpio/gpio-davinci.txt index a2e839d6e338..5079ba7d6568 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-davinci.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-davinci.txt @@ -1,13 +1,17 @@ -Davinci GPIO controller bindings +Davinci/Keystone GPIO controller bindings Required Properties: -- compatible: should be "ti,dm6441-gpio" +- compatible: should be "ti,dm6441-gpio", "ti,keystone-gpio" - reg: Physical base address of the controller and the size of memory mapped registers. - gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells : Should be two. + - first cell is the pin number + - second cell is used to specify optional parameters (unused) + - interrupt-parent: phandle of the parent interrupt controller. - interrupts: Array of GPIO interrupt number. Only banked or unbanked IRQs are @@ -27,6 +31,7 @@ Example: gpio: gpio@1e26000 { compatible = "ti,dm6441-gpio"; gpio-controller; + #gpio-cells = <2>; reg = <0x226000 0x1000>; interrupt-parent = <&intc>; interrupts = <42 IRQ_TYPE_EDGE_BOTH 43 IRQ_TYPE_EDGE_BOTH @@ -39,3 +44,19 @@ gpio: gpio@1e26000 { interrupt-controller; #interrupt-cells = <2>; }; + +leds { + compatible = "gpio-leds"; + + led1 { + label = "davinci:green:usr1"; + gpios = <&gpio 10 GPIO_ACTIVE_HIGH>; + ... + }; + + led2 { + label = "davinci:red:debug1"; + gpios = <&gpio 11 GPIO_ACTIVE_HIGH>; + ... + }; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt b/Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt new file mode 100644 index 000000000000..6c7e6c7302f5 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt @@ -0,0 +1,39 @@ +Keystone 2 DSP GPIO controller bindings + +HOST OS userland running on ARM can send interrupts to DSP cores using +the DSP GPIO controller IP. It provides 28 IRQ signals per each DSP core. +This is one of the component used by the IPC mechanism used on Keystone SOCs. + +For example TCI6638K2K SoC has 8 DSP GPIO controllers: + - 8 for C66x CorePacx CPUs 0-7 + +Keystone 2 DSP GPIO controller has specific features: +- each GPIO can be configured only as output pin; +- setting GPIO value to 1 causes IRQ generation on target DSP core; +- reading pin value returns 0 - if IRQ was handled or 1 - IRQ is still + pending. + +Required Properties: +- compatible: should be "ti,keystone-dsp-gpio" +- ti,syscon-dev: phandle/offset pair. The phandle to syscon used to + access device state control registers and the offset of device's specific + registers within device state control registers range. +- gpio-controller: Marks the device node as a gpio controller. +- #gpio-cells: Should be 2. + +Please refer to gpio.txt in this directory for details of the common GPIO +bindings used by client devices. + +Example: + dspgpio0: keystone_dsp_gpio@02620240 { + compatible = "ti,keystone-dsp-gpio"; + ti,syscon-dev = <&devctrl 0x240>; + gpio-controller; + #gpio-cells = <2>; + }; + + dsp0: dsp0 { + compatible = "linux,rproc-user"; + ... + kick-gpio = <&dspgpio0 27>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt index 3ddc7ccfe5f3..c306a2d0f2b1 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt @@ -54,7 +54,7 @@ Optional device specific properties: IO 8-15 are bank 2. These chips have two different interrupt outputs: One for bank 1 and another for bank 2. If irq-mirror is set, both interrupts are generated regardless of the bank that an input change - occured on. If it is not set, the interrupt are only generated for the + occurred on. If it is not set, the interrupt are only generated for the bank they belong to. On devices with only one interrupt output this property is useless. diff --git a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt new file mode 100644 index 000000000000..b9a42f294dd0 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt @@ -0,0 +1,39 @@ +* NXP PCA953x I2C GPIO multiplexer + +Required properties: + - compatible: Has to contain one of the following: + nxp,pca9505 + nxp,pca9534 + nxp,pca9535 + nxp,pca9536 + nxp,pca9537 + nxp,pca9538 + nxp,pca9539 + nxp,pca9554 + nxp,pca9555 + nxp,pca9556 + nxp,pca9557 + nxp,pca9574 + nxp,pca9575 + nxp,pca9698 + maxim,max7310 + maxim,max7312 + maxim,max7313 + maxim,max7315 + ti,pca6107 + ti,tca6408 + ti,tca6416 + ti,tca6424 + exar,xra1202 + +Example: + + + gpio@20 { + compatible = "nxp,pca9505"; + reg = <0x20>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pca9505>; + interrupt-parent = <&gpio3>; + interrupts = <23 IRQ_TYPE_LEVEL_LOW>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-restart.txt b/Documentation/devicetree/bindings/gpio/gpio-restart.txt new file mode 100644 index 000000000000..af3701bc15c4 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-restart.txt @@ -0,0 +1,54 @@ +Drive a GPIO line that can be used to restart the system from a restart +handler. + +This binding supports level and edge triggered reset. At driver load +time, the driver will request the given gpio line and install a restart +handler. If the optional properties 'open-source' is not found, the GPIO line +will be driven in the inactive state. Otherwise its not driven until +the restart is initiated. + +When the system is restarted, the restart handler will be invoked in +priority order. The gpio is configured as an output, and driven active, +triggering a level triggered reset condition. This will also cause an +inactive->active edge condition, triggering positive edge triggered +reset. After a delay specified by active-delay, the GPIO is set to +inactive, thus causing an active->inactive edge, triggering negative edge +triggered reset. After a delay specified by inactive-delay, the GPIO +is driven active again. After a delay specified by wait-delay, the +restart handler completes allowing other restart handlers to be attempted. + +Required properties: +- compatible : should be "gpio-restart". +- gpios : The GPIO to set high/low, see "gpios property" in + Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be + low to reset the board set it to "Active Low", otherwise set + gpio to "Active High". + +Optional properties: +- open-source : Treat the GPIO as being open source and defer driving + it to when the restart is initiated. If this optional property is not + specified, the GPIO is initialized as an output in its inactive state. +- priority : A priority ranging from 0 to 255 (default 128) according to + the following guidelines: + 0: Restart handler of last resort, with limited restart + capabilities + 128: Default restart handler; use if no other restart handler is + expected to be available, and/or if restart functionality is + sufficient to restart the entire system + 255: Highest priority restart handler, will preempt all other + restart handlers +- active-delay: Delay (default 100) to wait after driving gpio active [ms] +- inactive-delay: Delay (default 100) to wait after driving gpio inactive [ms] +- wait-delay: Delay (default 3000) to wait after completing restart + sequence [ms] + +Examples: + +gpio-restart { + compatible = "gpio-restart"; + gpios = <&gpio 4 0>; + priority = <128>; + active-delay = <100>; + inactive-delay = <100>; + wait-delay = <3000>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-xgene.txt b/Documentation/devicetree/bindings/gpio/gpio-xgene.txt new file mode 100644 index 000000000000..86dbb05e7758 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-xgene.txt @@ -0,0 +1,22 @@ +APM X-Gene SoC GPIO controller bindings + +This is a gpio controller that is part of the flash controller. +This gpio controller controls a total of 48 gpios. + +Required properties: +- compatible: "apm,xgene-gpio" for X-Gene GPIO controller +- reg: Physical base address and size of the controller's registers +- #gpio-cells: Should be two. + - first cell is the pin number + - second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +- gpio-controller: Marks the device node as a GPIO controller. + +Example: + gpio0: gpio0@1701c000 { + compatible = "apm,xgene-gpio"; + reg = <0x0 0x1701c000 0x0 0x40>; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-zevio.txt b/Documentation/devicetree/bindings/gpio/gpio-zevio.txt new file mode 100644 index 000000000000..a37bd9ae2730 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-zevio.txt @@ -0,0 +1,16 @@ +Zevio GPIO controller + +Required properties: +- compatible: Should be "lsi,zevio-gpio" +- reg: Address and length of the register set for the device +- #gpio-cells: Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). +- gpio-controller: Marks the device node as a GPIO controller. + +Example: + gpio: gpio@90000000 { + compatible = "lsi,zevio-gpio"; + reg = <0x90000000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-zynq.txt b/Documentation/devicetree/bindings/gpio/gpio-zynq.txt new file mode 100644 index 000000000000..986371a4be2c --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-zynq.txt @@ -0,0 +1,26 @@ +Xilinx Zynq GPIO controller Device Tree Bindings +------------------------------------------- + +Required properties: +- #gpio-cells : Should be two + - First cell is the GPIO line number + - Second cell is used to specify optional + parameters (unused) +- compatible : Should be "xlnx,zynq-gpio-1.0" +- clocks : Clock specifier (see clock bindings for details) +- gpio-controller : Marks the device node as a GPIO controller. +- interrupts : Interrupt specifier (see interrupt bindings for + details) +- interrupt-parent : Must be core interrupt controller +- reg : Address and length of the register set for the device + +Example: + gpio@e000a000 { + #gpio-cells = <2>; + compatible = "xlnx,zynq-gpio-1.0"; + clocks = <&clkc 42>; + gpio-controller; + interrupt-parent = <&intc>; + interrupts = <0 20 4>; + reg = <0xe000a000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index 0c85bb6e3a80..3fb8f53071b8 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -13,11 +13,11 @@ properties, each containing a 'gpio-list': gpio-specifier : Array of #gpio-cells specifying specific gpio (controller specific) -GPIO properties should be named "[<name>-]gpios". Exact +GPIO properties should be named "[<name>-]gpios". The exact meaning of each gpios property must be documented in the device tree binding for each device. -For example, the following could be used to describe gpios pins to use +For example, the following could be used to describe GPIO pins used as chip select lines; with chip selects 0, 1 and 3 populated, and chip select 2 left empty: @@ -44,35 +44,79 @@ whether pin is open-drain and whether pin is logically inverted. Exact meaning of each specifier cell is controller specific, and must be documented in the device tree binding for the device. -Example of the node using GPIOs: +Example of a node using GPIOs: node { gpios = <&qe_pio_e 18 0>; }; In this example gpio-specifier is "18 0" and encodes GPIO pin number, -and empty GPIO flags as accepted by the "qe_pio_e" gpio-controller. +and GPIO flags as accepted by the "qe_pio_e" gpio-controller. + +1.1) GPIO specifier best practices +---------------------------------- + +A gpio-specifier should contain a flag indicating the GPIO polarity; active- +high or active-low. If it does, the follow best practices should be followed: + +The gpio-specifier's polarity flag should represent the physical level at the +GPIO controller that achieves (or represents, for inputs) a logically asserted +value at the device. The exact definition of logically asserted should be +defined by the binding for the device. If the board inverts the signal between +the GPIO controller and the device, then the gpio-specifier will represent the +opposite physical level than the signal at the device's pin. + +When the device's signal polarity is configurable, the binding for the +device must either: + +a) Define a single static polarity for the signal, with the expectation that +any software using that binding would statically program the device to use +that signal polarity. + +The static choice of polarity may be either: + +a1) (Preferred) Dictated by a binding-specific DT property. + +or: + +a2) Defined statically by the DT binding itself. + +In particular, the polarity cannot be derived from the gpio-specifier, since +that would prevent the DT from separately representing the two orthogonal +concepts of configurable signal polarity in the device, and possible board- +level signal inversion. + +or: + +b) Pick a single option for device signal polarity, and document this choice +in the binding. The gpio-specifier should represent the polarity of the signal +(at the GPIO controller) assuming that the device is configured for this +particular signal polarity choice. If software chooses to program the device +to generate or receive a signal of the opposite polarity, software will be +responsible for correctly interpreting (inverting) the GPIO signal at the GPIO +controller. 2) gpio-controller nodes ------------------------ -Every GPIO controller node must both an empty "gpio-controller" -property, and have #gpio-cells contain the size of the gpio-specifier. +Every GPIO controller node must contain both an empty "gpio-controller" +property, and a #gpio-cells integer property, which indicates the number of +cells in a gpio-specifier. Example of two SOC GPIO banks defined as gpio-controller nodes: qe_pio_a: gpio-controller@1400 { - #gpio-cells = <2>; compatible = "fsl,qe-pario-bank-a", "fsl,qe-pario-bank"; reg = <0x1400 0x18>; gpio-controller; + #gpio-cells = <2>; }; qe_pio_e: gpio-controller@1460 { - #gpio-cells = <2>; compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; reg = <0x1460 0x18>; gpio-controller; + #gpio-cells = <2>; }; 2.1) gpio- and pin-controller interaction diff --git a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt index 66416261e14d..b2afdb27adeb 100644 --- a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt @@ -19,7 +19,7 @@ Required properties: - gpio-controller : Marks the device node as a gpio controller. - #gpio-cells : Should be one. It is the pin number. -Example: +Example for a MMP platform: gpio: gpio@d4019000 { compatible = "marvell,mmp-gpio"; @@ -32,6 +32,19 @@ Example: #interrupt-cells = <1>; }; +Example for a PXA3xx platform: + + gpio: gpio@40e00000 { + compatible = "intel,pxa3xx-gpio"; + reg = <0x40e00000 0x10000>; + interrupt-names = "gpio0", "gpio1", "gpio_mux"; + interrupts = <8 9 10>; + gpio-controller; + #gpio-cells = <0x2>; + interrupt-controller; + #interrupt-cells = <0x2>; + }; + * Marvell Orion GPIO Controller Required properties: diff --git a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt index f61cef74a212..941a26aa4322 100644 --- a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt +++ b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -21,6 +21,12 @@ Required Properties: GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. - gpio-ranges: Range of pins managed by the GPIO controller. +Optional properties: + + - clocks: Must contain a reference to the functional clock. The property is + mandatory if the hardware implements a controllable functional clock for + the GPIO instance. + Please refer to gpio.txt in this directory for details of gpio-ranges property and the common GPIO bindings used by client devices. diff --git a/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt b/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt new file mode 100644 index 000000000000..dd5d2c0394b1 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt @@ -0,0 +1,60 @@ +* Synopsys DesignWare APB GPIO controller + +Required properties: +- compatible : Should contain "snps,dw-apb-gpio" +- reg : Address and length of the register set for the device. +- #address-cells : should be 1 (for addressing port subnodes). +- #size-cells : should be 0 (port subnodes). + +The GPIO controller has a configurable number of ports, each of which are +represented as child nodes with the following properties: + +Required properties: +- compatible : "snps,dw-apb-gpio-port" +- gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +- reg : The integer port index of the port, a single cell. + +Optional properties: +- interrupt-controller : The first port may be configured to be an interrupt +controller. +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt. Shall be set to 2. The first cell defines the interrupt number, + the second encodes the triger flags encoded as described in + Documentation/devicetree/bindings/interrupts.txt +- interrupt-parent : The parent interrupt controller. +- interrupts : The interrupt to the parent controller raised when GPIOs + generate the interrupts. +- snps,nr-gpios : The number of pins in the port, a single cell. + +Example: + +gpio: gpio@20000 { + compatible = "snps,dw-apb-gpio"; + reg = <0x20000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + porta: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + snps,nr-gpios = <8>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&vic1>; + interrupts = <0>; + }; + + portb: gpio-controller@1 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + snps,nr-gpios = <8>; + reg = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/gpu/nvidia,gk20a.txt b/Documentation/devicetree/bindings/gpu/nvidia,gk20a.txt new file mode 100644 index 000000000000..23bfe8e1f7cc --- /dev/null +++ b/Documentation/devicetree/bindings/gpu/nvidia,gk20a.txt @@ -0,0 +1,43 @@ +NVIDIA GK20A Graphics Processing Unit + +Required properties: +- compatible: "nvidia,<chip>-<gpu>" + Currently recognized values: + - nvidia,tegra124-gk20a +- reg: Physical base address and length of the controller's registers. + Must contain two entries: + - first entry for bar0 + - second entry for bar1 +- interrupts: Must contain an entry for each entry in interrupt-names. + See ../interrupt-controller/interrupts.txt for details. +- interrupt-names: Must include the following entries: + - stall + - nonstall +- vdd-supply: regulator for supply voltage. +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - gpu + - pwr +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - gpu + +Example: + + gpu@0,57000000 { + compatible = "nvidia,gk20a"; + reg = <0x0 0x57000000 0x0 0x01000000>, + <0x0 0x58000000 0x0 0x01000000>; + interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "stall", "nonstall"; + vdd-supply = <&vdd_gpu>; + clocks = <&tegra_car TEGRA124_CLK_GPU>, + <&tegra_car TEGRA124_CLK_PLL_P_OUT5>; + clock-names = "gpu", "pwr"; + resets = <&tegra_car 184>; + reset-names = "gpu"; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt index efaeec8961b6..b48f4ef31d93 100644 --- a/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt +++ b/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt @@ -136,6 +136,7 @@ of the following host1x client modules: - compatible: "nvidia,tegra<chip>-hdmi" - reg: Physical base address and length of the controller's registers. - interrupts: The interrupt outputs from the controller. + - hdmi-supply: supply for the +5V HDMI connector pin - vdd-supply: regulator for supply voltage - pll-supply: regulator for PLL - clocks: Must contain an entry for each entry in clock-names. @@ -180,6 +181,7 @@ of the following host1x client modules: See ../reset/reset.txt for details. - reset-names: Must include the following entries: - dsi + - avdd-dsi-supply: phandle of a supply that powers the DSI controller - nvidia,mipi-calibrate: Should contain a phandle and a specifier specifying which pads are used by this DSI output and need to be calibrated. See also ../mipi/nvidia,tegra114-mipi.txt. @@ -190,6 +192,48 @@ of the following host1x client modules: - nvidia,edid: supplies a binary EDID blob - nvidia,panel: phandle of a display panel +- sor: serial output resource + + Required properties: + - compatible: "nvidia,tegra124-sor" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + - clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. + - clock-names: Must include the following entries: + - sor: clock input for the SOR hardware + - parent: input for the pixel clock + - dp: reference clock for the SOR clock + - safe: safe reference for the SOR clock during power up + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - sor + + Optional properties: + - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing + - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection + - nvidia,edid: supplies a binary EDID blob + - nvidia,panel: phandle of a display panel + + Optional properties when driving an eDP output: + - nvidia,dpaux: phandle to a DispayPort AUX interface + +- dpaux: DisplayPort AUX interface + - compatible: "nvidia,tegra124-dpaux" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + - clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. + - clock-names: Must include the following entries: + - dpaux: clock input for the DPAUX hardware + - parent: reference clock + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - dpaux + - vdd-supply: phandle of a supply that powers the DisplayPort link + Example: / { diff --git a/Documentation/devicetree/bindings/gpu/st,stih4xx.txt b/Documentation/devicetree/bindings/gpu/st,stih4xx.txt new file mode 100644 index 000000000000..2d150c311a05 --- /dev/null +++ b/Documentation/devicetree/bindings/gpu/st,stih4xx.txt @@ -0,0 +1,189 @@ +STMicroelectronics stih4xx platforms + +- sti-vtg: video timing generator + Required properties: + - compatible: "st,vtg" + - reg: Physical base address of the IP registers and length of memory mapped region. + Optional properties: + - interrupts : VTG interrupt number to the CPU. + - st,slave: phandle on a slave vtg + +- sti-vtac: video timing advanced inter dye communication Rx and TX + Required properties: + - compatible: "st,vtac-main" or "st,vtac-aux" + - reg: Physical base address of the IP registers and length of memory mapped region. + - clocks: from common clock binding: handle hardware IP needed clocks, the + number of clocks may depend of the SoC type. + See ../clocks/clock-bindings.txt for details. + - clock-names: names of the clocks listed in clocks property in the same + order. + +- sti-display-subsystem: Master device for DRM sub-components + This device must be the parent of all the sub-components and is responsible + of bind them. + Required properties: + - compatible: "st,sti-display-subsystem" + - ranges: to allow probing of subdevices + +- sti-compositor: frame compositor engine + must be a child of sti-display-subsystem + Required properties: + - compatible: "st,stih<chip>-compositor" + - reg: Physical base address of the IP registers and length of memory mapped region. + - clocks: from common clock binding: handle hardware IP needed clocks, the + number of clocks may depend of the SoC type. + See ../clocks/clock-bindings.txt for details. + - clock-names: names of the clocks listed in clocks property in the same + order. + - resets: resets to be used by the device + See ../reset/reset.txt for details. + - reset-names: names of the resets listed in resets property in the same + order. + - st,vtg: phandle(s) on vtg device (main and aux) nodes. + +- sti-tvout: video out hardware block + must be a child of sti-display-subsystem + Required properties: + - compatible: "st,stih<chip>-tvout" + - reg: Physical base address of the IP registers and length of memory mapped region. + - reg-names: names of the mapped memory regions listed in regs property in + the same order. + - resets: resets to be used by the device + See ../reset/reset.txt for details. + - reset-names: names of the resets listed in resets property in the same + order. + - ranges: to allow probing of subdevices + +- sti-hdmi: hdmi output block + must be a child of sti-tvout + Required properties: + - compatible: "st,stih<chip>-hdmi"; + - reg: Physical base address of the IP registers and length of memory mapped region. + - reg-names: names of the mapped memory regions listed in regs property in + the same order. + - interrupts : HDMI interrupt number to the CPU. + - interrupt-names: name of the interrupts listed in interrupts property in + the same order + - clocks: from common clock binding: handle hardware IP needed clocks, the + number of clocks may depend of the SoC type. + - clock-names: names of the clocks listed in clocks property in the same + order. + - hdmi,hpd-gpio: gpio id to detect if an hdmi cable is plugged or not. + +sti-hda: + Required properties: + must be a child of sti-tvout + - compatible: "st,stih<chip>-hda" + - reg: Physical base address of the IP registers and length of memory mapped region. + - reg-names: names of the mapped memory regions listed in regs property in + the same order. + - clocks: from common clock binding: handle hardware IP needed clocks, the + number of clocks may depend of the SoC type. + See ../clocks/clock-bindings.txt for details. + - clock-names: names of the clocks listed in clocks property in the same + order. + +Example: + +/ { + ... + + vtg_main_slave: sti-vtg-main-slave@fe85A800 { + compatible = "st,vtg"; + reg = <0xfe85A800 0x300>; + interrupts = <GIC_SPI 175 IRQ_TYPE_NONE>; + }; + + vtg_main: sti-vtg-main-master@fd348000 { + compatible = "st,vtg"; + reg = <0xfd348000 0x400>; + st,slave = <&vtg_main_slave>; + }; + + vtg_aux_slave: sti-vtg-aux-slave@fd348400 { + compatible = "st,vtg"; + reg = <0xfe858200 0x300>; + interrupts = <GIC_SPI 176 IRQ_TYPE_NONE>; + }; + + vtg_aux: sti-vtg-aux-master@fd348400 { + compatible = "st,vtg"; + reg = <0xfd348400 0x400>; + st,slave = <&vtg_aux_slave>; + }; + + + sti-vtac-rx-main@fee82800 { + compatible = "st,vtac-main"; + reg = <0xfee82800 0x200>; + clock-names = "vtac"; + clocks = <&clk_m_a2_div0 CLK_M_VTAC_MAIN_PHY>; + }; + + sti-vtac-rx-aux@fee82a00 { + compatible = "st,vtac-aux"; + reg = <0xfee82a00 0x200>; + clock-names = "vtac"; + clocks = <&clk_m_a2_div0 CLK_M_VTAC_AUX_PHY>; + }; + + sti-vtac-tx-main@fd349000 { + compatible = "st,vtac-main"; + reg = <0xfd349000 0x200>, <0xfd320000 0x10000>; + clock-names = "vtac"; + clocks = <&clk_s_a1_hs CLK_S_VTAC_TX_PHY>; + }; + + sti-vtac-tx-aux@fd349200 { + compatible = "st,vtac-aux"; + reg = <0xfd349200 0x200>, <0xfd320000 0x10000>; + clock-names = "vtac"; + clocks = <&clk_s_a1_hs CLK_S_VTAC_TX_PHY>; + }; + + sti-display-subsystem { + compatible = "st,sti-display-subsystem"; + ranges; + + sti-compositor@fd340000 { + compatible = "st,stih416-compositor"; + reg = <0xfd340000 0x1000>; + clock-names = "compo_main", "compo_aux", + "pix_main", "pix_aux"; + clocks = <&clk_m_a2_div1 CLK_M_COMPO_MAIN>, <&clk_m_a2_div1 CLK_M_COMPO_AUX>, + <&clockgen_c_vcc CLK_S_PIX_MAIN>, <&clockgen_c_vcc CLK_S_PIX_AUX>; + reset-names = "compo-main", "compo-aux"; + resets = <&softreset STIH416_COMPO_M_SOFTRESET>, <&softreset STIH416_COMPO_A_SOFTRESET>; + st,vtg = <&vtg_main>, <&vtg_aux>; + }; + + sti-tvout@fe000000 { + compatible = "st,stih416-tvout"; + reg = <0xfe000000 0x1000>, <0xfe85a000 0x400>, <0xfe830000 0x10000>; + reg-names = "tvout-reg", "hda-reg", "syscfg"; + reset-names = "tvout"; + resets = <&softreset STIH416_HDTVOUT_SOFTRESET>; + ranges; + + sti-hdmi@fe85c000 { + compatible = "st,stih416-hdmi"; + reg = <0xfe85c000 0x1000>, <0xfe830000 0x10000>; + reg-names = "hdmi-reg", "syscfg"; + interrupts = <GIC_SPI 173 IRQ_TYPE_NONE>; + interrupt-names = "irq"; + clock-names = "pix", "tmds", "phy", "audio"; + clocks = <&clockgen_c_vcc CLK_S_PIX_HDMI>, <&clockgen_c_vcc CLK_S_TMDS_HDMI>, <&clockgen_c_vcc CLK_S_HDMI_REJECT_PLL>, <&clockgen_b1 CLK_S_PCM_0>; + hdmi,hpd-gpio = <&PIO2 5>; + }; + + sti-hda@fe85a000 { + compatible = "st,stih416-hda"; + reg = <0xfe85a000 0x400>, <0xfe83085c 0x4>; + reg-names = "hda-reg", "video-dacs-ctrl"; + clock-names = "pix", "hddac"; + clocks = <&clockgen_c_vcc CLK_S_PIX_HD>, <&clockgen_c_vcc CLK_S_HDDAC>; + }; + }; + }; + ... +}; diff --git a/Documentation/devicetree/bindings/graph.txt b/Documentation/devicetree/bindings/graph.txt new file mode 100644 index 000000000000..1a69c078adf2 --- /dev/null +++ b/Documentation/devicetree/bindings/graph.txt @@ -0,0 +1,129 @@ +Common bindings for device graphs + +General concept +--------------- + +The hierarchical organisation of the device tree is well suited to describe +control flow to devices, but there can be more complex connections between +devices that work together to form a logical compound device, following an +arbitrarily complex graph. +There already is a simple directed graph between devices tree nodes using +phandle properties pointing to other nodes to describe connections that +can not be inferred from device tree parent-child relationships. The device +tree graph bindings described herein abstract more complex devices that can +have multiple specifiable ports, each of which can be linked to one or more +ports of other devices. + +These common bindings do not contain any information about the direction or +type of the connections, they just map their existence. Specific properties +may be described by specialized bindings depending on the type of connection. + +To see how this binding applies to video pipelines, for example, see +Documentation/device-tree/bindings/media/video-interfaces.txt. +Here the ports describe data interfaces, and the links between them are +the connecting data buses. A single port with multiple connections can +correspond to multiple devices being connected to the same physical bus. + +Organisation of ports and endpoints +----------------------------------- + +Ports are described by child 'port' nodes contained in the device node. +Each port node contains an 'endpoint' subnode for each remote device port +connected to this port. If a single port is connected to more than one +remote device, an 'endpoint' child node must be provided for each link. +If more than one port is present in a device node or there is more than one +endpoint at a port, or a port node needs to be associated with a selected +hardware interface, a common scheme using '#address-cells', '#size-cells' +and 'reg' properties is used number the nodes. + +device { + ... + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + endpoint@0 { + reg = <0>; + ... + }; + endpoint@1 { + reg = <1>; + ... + }; + }; + + port@1 { + reg = <1>; + + endpoint { ... }; + }; +}; + +All 'port' nodes can be grouped under an optional 'ports' node, which +allows to specify #address-cells, #size-cells properties for the 'port' +nodes independently from any other child device nodes a device might +have. + +device { + ... + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + ... + endpoint@0 { ... }; + endpoint@1 { ... }; + }; + + port@1 { ... }; + }; +}; + +Links between endpoints +----------------------- + +Each endpoint should contain a 'remote-endpoint' phandle property that points +to the corresponding endpoint in the port of the remote device. In turn, the +remote endpoint should contain a 'remote-endpoint' property. If it has one, +it must not point to another than the local endpoint. Two endpoints with their +'remote-endpoint' phandles pointing at each other form a link between the +containing ports. + +device-1 { + port { + device_1_output: endpoint { + remote-endpoint = <&device_2_input>; + }; + }; +}; + +device-2 { + port { + device_2_input: endpoint { + remote-endpoint = <&device_1_output>; + }; + }; +}; + + +Required properties +------------------- + +If there is more than one 'port' or more than one 'endpoint' node or 'reg' +property is present in port and/or endpoint nodes the following properties +are required in a relevant parent node: + + - #address-cells : number of cells required to define port/endpoint + identifier, should be 1. + - #size-cells : should be zero. + +Optional endpoint properties +---------------------------- + +- remote-endpoint: phandle to an 'endpoint' subnode of a remote device node. + diff --git a/Documentation/devicetree/bindings/hsi/client-devices.txt b/Documentation/devicetree/bindings/hsi/client-devices.txt new file mode 100644 index 000000000000..104c9a3e57a4 --- /dev/null +++ b/Documentation/devicetree/bindings/hsi/client-devices.txt @@ -0,0 +1,44 @@ +Each HSI port is supposed to have one child node, which +symbols the remote device connected to the HSI port. The +following properties are standardized for HSI clients: + +Required HSI configuration properties: + +- hsi-channel-ids: A list of channel ids + +- hsi-rx-mode: Receiver Bit transmission mode ("stream" or "frame") +- hsi-tx-mode: Transmitter Bit transmission mode ("stream" or "frame") +- hsi-mode: May be used instead hsi-rx-mode and hsi-tx-mode if + the transmission mode is the same for receiver and + transmitter +- hsi-speed-kbps: Max bit transmission speed in kbit/s +- hsi-flow: RX flow type ("synchronized" or "pipeline") +- hsi-arb-mode: Arbitration mode for TX frame ("round-robin", "priority") + +Optional HSI configuration properties: + +- hsi-channel-names: A list with one name per channel specified in the + hsi-channel-ids property + + +Device Tree node example for an HSI client: + +hsi-controller { + hsi-port { + modem: hsi-client { + compatible = "nokia,n900-modem"; + + hsi-channel-ids = <0>, <1>, <2>, <3>; + hsi-channel-names = "mcsaab-control", + "speech-control", + "speech-data", + "mcsaab-data"; + hsi-speed-kbps = <55000>; + hsi-mode = "frame"; + hsi-flow = "synchronized"; + hsi-arb-mode = "round-robin"; + + /* more client specific properties */ + }; + }; +}; diff --git a/Documentation/devicetree/bindings/hsi/nokia-modem.txt b/Documentation/devicetree/bindings/hsi/nokia-modem.txt new file mode 100644 index 000000000000..8a979780452b --- /dev/null +++ b/Documentation/devicetree/bindings/hsi/nokia-modem.txt @@ -0,0 +1,57 @@ +Nokia modem client bindings + +The Nokia modem HSI client follows the common HSI client binding +and inherits all required properties. The following additional +properties are needed by the Nokia modem HSI client: + +Required properties: +- compatible: Should be one of + "nokia,n900-modem" +- hsi-channel-names: Should contain the following strings + "mcsaab-control" + "speech-control" + "speech-data" + "mcsaab-data" +- gpios: Should provide a GPIO handler for each GPIO listed in + gpio-names +- gpio-names: Should contain the following strings + "cmt_apeslpx" + "cmt_rst_rq" + "cmt_en" + "cmt_rst" + "cmt_bsi" +- interrupts: Should be IRQ handle for modem's reset indication + +Example: + +&ssi_port { + modem: hsi-client { + compatible = "nokia,n900-modem"; + + pinctrl-names = "default"; + pinctrl-0 = <&modem_pins>; + + hsi-channel-ids = <0>, <1>, <2>, <3>; + hsi-channel-names = "mcsaab-control", + "speech-control", + "speech-data", + "mcsaab-data"; + hsi-speed-kbps = <55000>; + hsi-mode = "frame"; + hsi-flow = "synchronized"; + hsi-arb-mode = "round-robin"; + + interrupts-extended = <&gpio3 8 IRQ_TYPE_EDGE_FALLING>; /* 72 */ + + gpios = <&gpio3 6 GPIO_ACTIVE_HIGH>, /* 70 */ + <&gpio3 9 GPIO_ACTIVE_HIGH>, /* 73 */ + <&gpio3 10 GPIO_ACTIVE_HIGH>, /* 74 */ + <&gpio3 11 GPIO_ACTIVE_HIGH>, /* 75 */ + <&gpio5 29 GPIO_ACTIVE_HIGH>; /* 157 */ + gpio-names = "cmt_apeslpx", + "cmt_rst_rq", + "cmt_en", + "cmt_rst", + "cmt_bsi"; + }; +}; diff --git a/Documentation/devicetree/bindings/hsi/omap-ssi.txt b/Documentation/devicetree/bindings/hsi/omap-ssi.txt new file mode 100644 index 000000000000..f26625e42693 --- /dev/null +++ b/Documentation/devicetree/bindings/hsi/omap-ssi.txt @@ -0,0 +1,97 @@ +OMAP SSI controller bindings + +OMAP Synchronous Serial Interface (SSI) controller implements a legacy +variant of MIPI's High Speed Synchronous Serial Interface (HSI). + +Required properties: +- compatible: Should include "ti,omap3-ssi". +- reg-names: Contains the values "sys" and "gdd" (in this order). +- reg: Contains a matching register specifier for each entry + in reg-names. +- interrupt-names: Contains the value "gdd_mpu". +- interrupts: Contains matching interrupt information for each entry + in interrupt-names. +- ranges: Represents the bus address mapping between the main + controller node and the child nodes below. +- clock-names: Must include the following entries: + "ssi_ssr_fck": The OMAP clock of that name + "ssi_sst_fck": The OMAP clock of that name + "ssi_ick": The OMAP clock of that name +- clocks: Contains a matching clock specifier for each entry in + clock-names. +- #address-cells: Should be set to <1> +- #size-cells: Should be set to <1> + +Each port is represented as a sub-node of the ti,omap3-ssi device. + +Required Port sub-node properties: +- compatible: Should be set to the following value + ti,omap3-ssi-port (applicable to OMAP34xx devices) +- reg-names: Contains the values "tx" and "rx" (in this order). +- reg: Contains a matching register specifier for each entry + in reg-names. +- interrupt-parent Should be a phandle for the interrupt controller +- interrupts: Should contain interrupt specifiers for mpu interrupts + 0 and 1 (in this order). +- ti,ssi-cawake-gpio: Defines which GPIO pin is used to signify CAWAKE + events for the port. This is an optional board-specific + property. If it's missing the port will not be + enabled. + +Example for Nokia N900: + +ssi-controller@48058000 { + compatible = "ti,omap3-ssi"; + + /* needed until hwmod is updated to use the compatible string */ + ti,hwmods = "ssi"; + + reg = <0x48058000 0x1000>, + <0x48059000 0x1000>; + reg-names = "sys", + "gdd"; + + interrupts = <55>; + interrupt-names = "gdd_mpu"; + + clocks = <&ssi_ssr_fck>, + <&ssi_sst_fck>, + <&ssi_ick>; + clock-names = "ssi_ssr_fck", + "ssi_sst_fck", + "ssi_ick"; + + #address-cells = <1>; + #size-cells = <1>; + ranges; + + ssi-port@4805a000 { + compatible = "ti,omap3-ssi-port"; + + reg = <0x4805a000 0x800>, + <0x4805a800 0x800>; + reg-names = "tx", + "rx"; + + interrupt-parent = <&intc>; + interrupts = <67>, + <68>; + + ti,ssi-cawake-gpio = <&gpio5 23 GPIO_ACTIVE_HIGH>; /* 151 */ + } + + ssi-port@4805a000 { + compatible = "ti,omap3-ssi-port"; + + reg = <0x4805b000 0x800>, + <0x4805b800 0x800>; + reg-names = "tx", + "rx"; + + interrupt-parent = <&intc>; + interrupts = <69>, + <70>; + + status = "disabled"; /* second port is not used on N900 */ + } +} diff --git a/Documentation/devicetree/bindings/hwmon/ibmpowernv.txt b/Documentation/devicetree/bindings/hwmon/ibmpowernv.txt new file mode 100644 index 000000000000..f93242be60a1 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/ibmpowernv.txt @@ -0,0 +1,23 @@ +IBM POWERNV platform sensors +---------------------------- + +Required node properties: +- compatible: must be one of + "ibm,opal-sensor-cooling-fan" + "ibm,opal-sensor-amb-temp" + "ibm,opal-sensor-power-supply" + "ibm,opal-sensor-power" +- sensor-id: an opaque id provided by the firmware to the kernel, identifies a + given sensor and its attribute data + +Example sensors node: + +cooling-fan#8-data { + sensor-id = <0x7052107>; + compatible = "ibm,opal-sensor-cooling-fan"; +}; + +amb-temp#1-thrs { + sensor-id = <0x5096000>; + compatible = "ibm,opal-sensor-amb-temp"; +}; diff --git a/Documentation/devicetree/bindings/hwmon/ltc2978.txt b/Documentation/devicetree/bindings/hwmon/ltc2978.txt new file mode 100644 index 000000000000..ed2f09dc2483 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/ltc2978.txt @@ -0,0 +1,39 @@ +ltc2978 + +Required properties: +- compatible: should contain one of: + * "lltc,ltc2974" + * "lltc,ltc2977" + * "lltc,ltc2978" + * "lltc,ltc3880" + * "lltc,ltc3883" + * "lltc,ltm4676" +- reg: I2C slave address + +Optional properties: +- regulators: A node that houses a sub-node for each regulator controlled by + the device. Each sub-node is identified using the node's name, with valid + values listed below. The content of each sub-node is defined by the + standard binding for regulators; see regulator.txt. + +Valid names of regulators depend on number of supplies supported per device: + * ltc2974 : vout0 - vout3 + * ltc2977 : vout0 - vout7 + * ltc2978 : vout0 - vout7 + * ltc3880 : vout0 - vout1 + * ltc3883 : vout0 + * ltm4676 : vout0 - vout1 + +Example: +ltc2978@5e { + compatible = "lltc,ltc2978"; + reg = <0x5e>; + regulators { + vout0 { + regulator-name = "FPGA-2.5V"; + }; + vout2 { + regulator-name = "FPGA-1.5V"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt index c6f66674f19c..fcca8e744f41 100644 --- a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt +++ b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt @@ -3,11 +3,20 @@ NTC Thermistor hwmon sensors Requires node properties: - "compatible" value : one of - "ntc,ncp15wb473" - "ntc,ncp18wb473" - "ntc,ncp21wb473" - "ntc,ncp03wb473" - "ntc,ncp15wl333" + "epcos,b57330v2103" + "murata,ncp15wb473" + "murata,ncp18wb473" + "murata,ncp21wb473" + "murata,ncp03wb473" + "murata,ncp15wl333" + +/* Usage of vendor name "ntc" is deprecated */ +<DEPRECATED> "ntc,ncp15wb473" +<DEPRECATED> "ntc,ncp18wb473" +<DEPRECATED> "ntc,ncp21wb473" +<DEPRECATED> "ntc,ncp03wb473" +<DEPRECATED> "ntc,ncp15wl333" + - "pullup-uv" Pull up voltage in micro volts - "pullup-ohm" Pull up resistor value in ohms - "pulldown-ohm" Pull down resistor value in ohms @@ -16,12 +25,15 @@ Requires node properties: - "io-channels" Channel node of ADC to be used for conversion. +Optional node properties: +- "#thermal-sensor-cells" Used to expose itself to thermal fw. + Read more about iio bindings at Documentation/devicetree/bindings/iio/iio-bindings.txt Example: ncp15wb473@0 { - compatible = "ntc,ncp15wb473"; + compatible = "murata,ncp15wb473"; pullup-uv = <1800000>; pullup-ohm = <47000>; pulldown-ohm = <0>; diff --git a/Documentation/devicetree/bindings/hwmon/pwm-fan.txt b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt new file mode 100644 index 000000000000..610757ce4492 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt @@ -0,0 +1,12 @@ +Bindings for a fan connected to the PWM lines + +Required properties: +- compatible : "pwm-fan" +- pwms : the PWM that is used to control the PWM fan + +Example: + pwm-fan { + compatible = "pwm-fan"; + status = "okay"; + pwms = <&pwm 0 10000 0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt b/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt index 1ac8ea8ade1d..bfeabb843941 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt @@ -8,6 +8,12 @@ the standard I2C multi-master rules. Using GPIOs is generally useful in the case where there is a device on the bus that has errata and/or bugs that makes standard multimaster mode not feasible. +Note that this scheme works well enough but has some downsides: +* It is nonstandard (not using standard I2C multimaster) +* Having two masters on a bus in general makes it relatively hard to debug + problems (hard to tell if i2c issues were caused by one master, another, or + some device on the bus). + Algorithm: diff --git a/Documentation/devicetree/bindings/i2c/i2c-at91.txt b/Documentation/devicetree/bindings/i2c/i2c-at91.txt index 4fade84bea16..388f0a275fba 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-at91.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-at91.txt @@ -12,6 +12,7 @@ Required properties : - clocks: phandles to input clocks. Optional properties: +- clock-frequency: Desired I2C bus frequency in Hz, otherwise defaults to 100000 - Child nodes conforming to i2c bus binding Examples : @@ -23,6 +24,7 @@ i2c0: i2c@fff84000 { #address-cells = <1>; #size-cells = <0>; clocks = <&twi0_clk>; + clock-frequency = <400000>; 24c512@50 { compatible = "24c512"; diff --git a/Documentation/devicetree/bindings/i2c/i2c-axxia.txt b/Documentation/devicetree/bindings/i2c/i2c-axxia.txt new file mode 100644 index 000000000000..2296d782b4c2 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-axxia.txt @@ -0,0 +1,30 @@ +LSI Axxia I2C + +Required properties : +- compatible : Must be "lsi,api2c" +- reg : Offset and length of the register set for the device +- interrupts : the interrupt specifier +- #address-cells : Must be <1>; +- #size-cells : Must be <0>; +- clock-names : Must contain "i2c". +- clocks: Must contain an entry for each name in clock-names. See the common + clock bindings. + +Optional properties : +- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, + the default 100 kHz frequency will be used. As only Normal and Fast modes + are supported, possible values are 100000 and 400000. + +Example : + +i2c@02010084000 { + compatible = "lsi,api2c"; + device_type = "i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x20 0x10084000 0x00 0x1000>; + interrupts = <0 19 4>; + clocks = <&clk_per>; + clock-names = "i2c"; + clock-frequency = <400000>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-cadence.txt b/Documentation/devicetree/bindings/i2c/i2c-cadence.txt new file mode 100644 index 000000000000..7cb0b5608f49 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-cadence.txt @@ -0,0 +1,24 @@ +Binding for the Cadence I2C controller + +Required properties: + - reg: Physical base address and size of the controller's register area. + - compatible: Compatibility string. Must be 'cdns,i2c-r1p10'. + - clocks: Input clock specifier. Refer to common clock bindings. + - interrupts: Interrupt specifier. Refer to interrupt bindings. + - #address-cells: Should be 1. + - #size-cells: Should be 0. + +Optional properties: + - clock-frequency: Desired operating frequency, in Hz, of the bus. + - clock-names: Input clock name, should be 'pclk'. + +Example: + i2c@e0004000 { + compatible = "cdns,i2c-r1p10"; + clocks = <&clkc 38>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + reg = <0xe0004000 0x1000>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-cros-ec-tunnel.txt b/Documentation/devicetree/bindings/i2c/i2c-cros-ec-tunnel.txt new file mode 100644 index 000000000000..898f030eba62 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-cros-ec-tunnel.txt @@ -0,0 +1,39 @@ +I2C bus that tunnels through the ChromeOS EC (cros-ec) +====================================================== +On some ChromeOS board designs we've got a connection to the EC (embedded +controller) but no direct connection to some devices on the other side of +the EC (like a battery and PMIC). To get access to those devices we need +to tunnel our i2c commands through the EC. + +The node for this device should be under a cros-ec node like google,cros-ec-spi +or google,cros-ec-i2c. + + +Required properties: +- compatible: google,cros-ec-i2c-tunnel +- google,remote-bus: The EC bus we'd like to talk to. + +Optional child nodes: +- One node per I2C device connected to the tunnelled I2C bus. + + +Example: + cros-ec@0 { + compatible = "google,cros-ec-spi"; + + ... + + i2c-tunnel { + compatible = "google,cros-ec-i2c-tunnel"; + #address-cells = <1>; + #size-cells = <0>; + + google,remote-bus = <0>; + + battery: sbs-battery@b { + compatible = "sbs,sbs-battery"; + reg = <0xb>; + sbs,poll-retry-count = <1>; + }; + }; + } diff --git a/Documentation/devicetree/bindings/i2c/i2c-designware.txt b/Documentation/devicetree/bindings/i2c/i2c-designware.txt index 7fd7fa25e9b0..5199b0c8cf7a 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-designware.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-designware.txt @@ -14,6 +14,12 @@ Optional properties : - i2c-sda-hold-time-ns : should contain the SDA hold time in nanoseconds. This option is only supported in hardware blocks version 1.11a or newer. + - i2c-scl-falling-time : should contain the SCL falling time in nanoseconds. + This value which is by default 300ns is used to compute the tLOW period. + + - i2c-sda-falling-time : should contain the SDA falling time in nanoseconds. + This value which is by default 300ns is used to compute the tHIGH period. + Example : i2c@f0000 { @@ -34,4 +40,6 @@ Example : interrupts = <12 1>; clock-frequency = <400000>; i2c-sda-hold-time-ns = <300>; + i2c-sda-falling-time-ns = <300>; + i2c-scl-falling-time-ns = <300>; }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-efm32.txt b/Documentation/devicetree/bindings/i2c/i2c-efm32.txt new file mode 100644 index 000000000000..50b25c3da186 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-efm32.txt @@ -0,0 +1,34 @@ +* Energymicro efm32 i2c controller + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : should be "energymicro,efm32-i2c" + - interrupts : the interrupt number + - clocks : reference to the module clock + +Recommended properties : + + - clock-frequency : maximal I2C bus clock frequency in Hz. + - energymicro,location : Decides the location of the USART I/O pins. + Allowed range : [0 .. 6] + +Example: + i2c0: i2c@4000a000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "energymicro,efm32-i2c"; + reg = <0x4000a000 0x400>; + interrupts = <9>; + clocks = <&cmu clk_HFPERCLKI2C0>; + clock-frequency = <100000>; + status = "ok"; + energymicro,location = <3>; + + eeprom@50 { + compatible = "microchip,24c02"; + reg = <0x50>; + pagesize = <16>; + }; + }; + diff --git a/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt index 056732cfdcee..2dbc0b62daa6 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt @@ -5,7 +5,16 @@ at various speeds ranging from 100khz to 3.4Mhz. Required properties: - compatible: value should be. - -> "samsung,exynos5-hsi2c", for i2c compatible with exynos5 hsi2c. + -> "samsung,exynos5-hsi2c", (DEPRECATED) + for i2c compatible with HSI2C available + on Exynos5250 and Exynos5420 SoCs. + -> "samsung,exynos5250-hsi2c", for i2c compatible with HSI2C available + on Exynos5250 and Exynos5420 SoCs. + -> "samsung,exynos5260-hsi2c", for i2c compatible with HSI2C available + on Exynos5260 SoCs. + -> "samsung,exynos7-hsi2c", for i2c compatible with HSI2C available + on Exynos7 SoCs. + - reg: physical base address of the controller and length of memory mapped region. - interrupts: interrupt number to the cpu. @@ -26,7 +35,7 @@ Optional properties: Example: hsi2c@12ca0000 { - compatible = "samsung,exynos5-hsi2c"; + compatible = "samsung,exynos5250-hsi2c"; reg = <0x12ca0000 0x100>; interrupts = <56>; clock-frequency = <100000>; diff --git a/Documentation/devicetree/bindings/i2c/i2c-hix5hd2.txt b/Documentation/devicetree/bindings/i2c/i2c-hix5hd2.txt new file mode 100644 index 000000000000..f98b37401e6e --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-hix5hd2.txt @@ -0,0 +1,24 @@ +I2C for Hisilicon hix5hd2 chipset platform + +Required properties: +- compatible: Must be "hisilicon,hix5hd2-i2c" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: interrupt number to the cpu. +- #address-cells = <1>; +- #size-cells = <0>; +- clocks: phandles to input clocks. + +Optional properties: +- clock-frequency: Desired I2C bus frequency in Hz, otherwise defaults to 100000 +- Child nodes conforming to i2c bus binding + +Examples: +I2C0@f8b10000 { + compatible = "hisilicon,hix5hd2-i2c"; + reg = <0xf8b10000 0x1000>; + interrupts = <0 38 4>; + clocks = <&clock HIX5HD2_I2C0_RST>; + #address-cells = <1>; + #size-cells = <0>; +} diff --git a/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt index 582b4652a82a..5c30026921ae 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt @@ -4,12 +4,16 @@ Required properties : - reg : Offset and length of the register set for the device - - compatible : Should be "marvell,mv64xxx-i2c" or "allwinner,sun4i-i2c" - or "marvell,mv78230-i2c" or "marvell,mv78230-a0-i2c" - Note: Only use "marvell,mv78230-a0-i2c" for a very rare, - initial version of the SoC which had broken offload - support. Linux auto-detects this and sets it - appropriately. + - compatible : Should be either: + - "allwinner,sun4i-a10-i2c" + - "allwinner,sun6i-a31-i2c" + - "marvell,mv64xxx-i2c" + - "marvell,mv78230-i2c" + - "marvell,mv78230-a0-i2c" + * Note: Only use "marvell,mv78230-a0-i2c" for a + very rare, initial version of the SoC which + had broken offload support. Linux + auto-detects this and sets it appropriately. - interrupts : The interrupt number Optional properties : @@ -17,6 +21,10 @@ Optional properties : - clock-frequency : Desired I2C bus clock frequency in Hz. If not set the default frequency is 100kHz + - resets : phandle to the parent reset controller. Mandatory + whenever you're using the "allwinner,sun6i-a31-i2c" + compatible. + Examples: i2c@11000 { diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt index 897cfcd5ce92..16b3e07aa98f 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt @@ -6,6 +6,10 @@ Required properties: "renesas,i2c-r8a7778" "renesas,i2c-r8a7779" "renesas,i2c-r8a7790" + "renesas,i2c-r8a7791" + "renesas,i2c-r8a7792" + "renesas,i2c-r8a7793" + "renesas,i2c-r8a7794" - reg: physical base address of the controller and length of memory mapped region. - interrupts: interrupt specifier. @@ -13,11 +17,16 @@ Required properties: Optional properties: - clock-frequency: desired I2C bus clock frequency in Hz. The absence of this propoerty indicates the default frequency 100 kHz. +- clocks: clock specifier. Examples : -i2c0: i2c@e6500000 { - compatible = "renesas,i2c-rcar-h2"; - reg = <0 0xe6500000 0 0x428>; - interrupts = <0 174 0x4>; +i2c0: i2c@e6508000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,i2c-r8a7791"; + reg = <0 0xe6508000 0 0x40>; + interrupts = <0 287 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7791_CLK_I2C0>; + clock-frequency = <400000>; }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt new file mode 100644 index 000000000000..dde6c22ce91a --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt @@ -0,0 +1,42 @@ +* Rockchip RK3xxx I2C controller + +This driver interfaces with the native I2C controller present in Rockchip +RK3xxx SoCs. + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : should be "rockchip,rk3066-i2c", "rockchip,rk3188-i2c" or + "rockchip,rk3288-i2c". + - interrupts : interrupt number + - clocks : parent clock + +Required on RK3066, RK3188 : + + - rockchip,grf : the phandle of the syscon node for the general register + file (GRF) + - on those SoCs an alias with the correct I2C bus ID (bit offset in the GRF) + is also required. + +Optional properties : + + - clock-frequency : SCL frequency to use (in Hz). If omitted, 100kHz is used. + +Example: + +aliases { + i2c0 = &i2c0; +} + +i2c0: i2c@2002d000 { + compatible = "rockchip,rk3188-i2c"; + reg = <0x2002d000 0x1000>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + + rockchip,grf = <&grf>; + + clock-names = "i2c"; + clocks = <&cru PCLK_I2C0>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt index 278de8e64bbf..89b3250f049b 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt @@ -32,6 +32,7 @@ Optional properties: specified, default value is 0. - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not specified, the default value in Hz is 100000. + - samsung,sysreg-phandle - handle to syscon used to control the system registers Example: diff --git a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt new file mode 100644 index 000000000000..d2153ce36fa8 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt @@ -0,0 +1,26 @@ +Device tree configuration for Renesas IIC (sh_mobile) driver + +Required properties: +- compatible : "renesas,iic-<soctype>". "renesas,rmobile-iic" as fallback +- reg : address start and address range size of device +- interrupts : interrupt of device +- clocks : clock for device +- #address-cells : should be <1> +- #size-cells : should be <0> + +Optional properties: +- clock-frequency : frequency of bus clock in Hz. Default 100kHz if unset. + +Pinctrl properties might be needed, too. See there. + +Example: + + iic0: i2c@e6500000 { + compatible = "renesas,iic-r8a7790", "renesas,rmobile-iic"; + reg = <0 0xe6500000 0 0x425>; + interrupts = <0 174 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A7790_CLK_IIC0>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt b/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt new file mode 100644 index 000000000000..6b765485af7d --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt @@ -0,0 +1,41 @@ + +* Allwinner P2WI (Push/Pull 2 Wire Interface) controller + +Required properties : + + - reg : Offset and length of the register set for the device. + - compatible : Should one of the following: + - "allwinner,sun6i-a31-p2wi" + - interrupts : The interrupt line connected to the P2WI peripheral. + - clocks : The gate clk connected to the P2WI peripheral. + - resets : The reset line connected to the P2WI peripheral. + +Optional properties : + + - clock-frequency : Desired P2WI bus clock frequency in Hz. If not set the +default frequency is 100kHz + +A P2WI may contain one child node encoding a P2WI slave device. + +Slave device properties: + Required properties: + - reg : the I2C slave address used during the initialization + process to switch from I2C to P2WI mode + +Example: + + p2wi@01f03400 { + compatible = "allwinner,sun6i-a31-p2wi"; + reg = <0x01f03400 0x400>; + interrupts = <0 39 4>; + clocks = <&apb0_gates 3>; + clock-frequency = <6000000>; + resets = <&apb0_rst 3>; + + axp221: pmic@68 { + compatible = "x-powers,axp221"; + reg = <0x68>; + + /* ... */ + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt b/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt new file mode 100644 index 000000000000..dc71754a56af --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt @@ -0,0 +1,40 @@ +Qualcomm Universal Peripheral (QUP) I2C controller + +Required properties: + - compatible: Should be: + * "qcom,i2c-qup-v1.1.1" for 8660, 8960 and 8064. + * "qcom,i2c-qup-v2.1.1" for 8974 v1. + * "qcom,i2c-qup-v2.2.1" for 8974 v2 and later. + - reg: Should contain QUP register address and length. + - interrupts: Should contain I2C interrupt. + + - clocks: A list of phandles + clock-specifiers, one for each entry in + clock-names. + - clock-names: Should contain: + * "core" for the core clock + * "iface" for the AHB clock + + - #address-cells: Should be <1> Address cells for i2c device address + - #size-cells: Should be <0> as i2c addresses have no size component + +Optional properties: + - clock-frequency: Should specify the desired i2c bus clock frequency in Hz, + defaults to 100kHz if omitted. + +Child nodes should conform to i2c bus binding. + +Example: + + i2c@f9924000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0xf9924000 0x1000>; + interrupts = <0 96 0>; + + clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + + clock-frequency = <355000>; + + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/ti,bq32k.txt b/Documentation/devicetree/bindings/i2c/ti,bq32k.txt new file mode 100644 index 000000000000..e204906b9ad3 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/ti,bq32k.txt @@ -0,0 +1,18 @@ +* TI BQ32000 I2C Serial Real-Time Clock + +Required properties: +- compatible: Should contain "ti,bq32000". +- reg: I2C address for chip + +Optional properties: +- trickle-resistor-ohms : Selected resistor for trickle charger + Values usable are 1120 and 20180 + Should be given if trickle charger should be enabled +- trickle-diode-disable : Do not use internal trickle charger diode + Should be given if internal trickle charger diode should be disabled +Example: + bq32000: rtc@68 { + compatible = "ti,bq32000"; + trickle-resistor-ohms = <1120>; + reg = <0x68>; + }; diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index 1a1ac2e560e9..605dcca5dbec 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -13,14 +13,28 @@ ad,ad7414 SMBus/I2C Digital Temperature Sensor in 6-Pin SOT with SMBus Alert an ad,adm9240 ADM9240: Complete System Hardware Monitor for uProcessor-Based Systems adi,adt7461 +/-1C TDM Extended Temp Range I.C adt7461 +/-1C TDM Extended Temp Range I.C +adi,adt7473 +/-1C TDM Extended Temp Range I.C +adi,adt7475 +/-1C TDM Extended Temp Range I.C +adi,adt7476 +/-1C TDM Extended Temp Range I.C +adi,adt7490 +/-1C TDM Extended Temp Range I.C at,24c08 i2c serial eeprom (24cxx) +atmel,24c00 i2c serial eeprom (24cxx) +atmel,24c01 i2c serial eeprom (24cxx) atmel,24c02 i2c serial eeprom (24cxx) +atmel,24c04 i2c serial eeprom (24cxx) +atmel,24c16 i2c serial eeprom (24cxx) +atmel,24c32 i2c serial eeprom (24cxx) +atmel,24c64 i2c serial eeprom (24cxx) +atmel,24c128 i2c serial eeprom (24cxx) +atmel,24c256 i2c serial eeprom (24cxx) +atmel,24c512 i2c serial eeprom (24cxx) +atmel,24c1024 i2c serial eeprom (24cxx) atmel,at97sc3204t i2c trusted platform module (TPM) capella,cm32181 CM32181: Ambient Light Sensor catalyst,24c32 i2c serial eeprom +cirrus,cs42l51 Cirrus Logic CS42L51 audio codec dallas,ds1307 64 x 8, Serial, I2C Real-Time Clock dallas,ds1338 I2C RTC with 56-Byte NV RAM -dallas,ds1339 I2C Serial Real-Time Clock dallas,ds1340 I2C RTC with Trickle Charger dallas,ds1374 I2C, 32-Bit Binary Counter Watchdog RTC with Trickle Charger and Reset Input/Output dallas,ds1631 High-Precision Digital Thermometer @@ -29,35 +43,42 @@ dallas,ds1775 Tiny Digital Thermometer and Thermostat dallas,ds3232 Extremely Accurate I²C RTC with Integrated Crystal and SRAM dallas,ds4510 CPU Supervisor with Nonvolatile Memory and Programmable I/O dallas,ds75 Digital Thermometer and Thermostat -dialog,da9053 DA9053: flexible system level PMIC with multicore support +dlg,da9053 DA9053: flexible system level PMIC with multicore support epson,rx8025 High-Stability. I2C-Bus INTERFACE REAL TIME CLOCK MODULE epson,rx8581 I2C-BUS INTERFACE REAL TIME CLOCK MODULE fsl,mag3110 MAG3110: Xtrinsic High Accuracy, 3D Magnetometer fsl,mc13892 MC13892: Power Management Integrated Circuit (PMIC) for i.MX35/51 fsl,mma8450 MMA8450Q: Xtrinsic Low-power, 3-axis Xtrinsic Accelerometer +fsl,mma8452 MMA8452Q: 3-axis 12-bit / 8-bit Digital Accelerometer fsl,mpr121 MPR121: Proximity Capacitive Touch Sensor Controller fsl,sgtl5000 SGTL5000: Ultra Low-Power Audio Codec gmt,g751 G751: Digital Temperature Sensor and Thermal Watchdog with Two-Wire Interface infineon,slb9635tt Infineon SLB9635 (Soft-) I2C TPM (old protocol, max 100khz) infineon,slb9645tt Infineon SLB9645 I2C TPM (new protocol, max 400khz) isl,isl12057 Intersil ISL12057 I2C RTC Chip +isil,isl29028 (deprecated, use isl) +isl,isl29028 Intersil ISL29028 Ambient Light and Proximity Sensor maxim,ds1050 5 Bit Programmable, Pulse-Width Modulator maxim,max1237 Low-Power, 4-/12-Channel, 2-Wire Serial, 12-Bit ADCs maxim,max6625 9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface mc,rv3029c2 Real Time Clock Module with I2C-Bus +national,lm63 Temperature sensor with integrated fan control national,lm75 I2C TEMP SENSOR national,lm80 Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor +national,lm85 Temperature sensor with integrated fan control national,lm92 ±0.33°C Accurate, 12-Bit + Sign Temperature Sensor and Thermal Window Comparator with Two-Wire Interface nuvoton,npct501 i2c trusted platform module (TPM) nxp,pca9556 Octal SMBus and I2C registered interface nxp,pca9557 8-bit I2C-bus and SMBus I/O port with reset nxp,pcf8563 Real-time clock/calendar +nxp,pcf85063 Tiny Real-Time Clock ovti,ov5642 OV5642: Color CMOS QSXGA (5-megapixel) Image Sensor with OmniBSI and Embedded TrueFocus pericom,pt7c4338 Real-time Clock Module plx,pex8648 48-Lane, 12-Port PCI Express Gen 2 (5.0 GT/s) Switch ramtron,24c64 i2c serial eeprom (24cxx) ricoh,rs5c372a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC samsung,24ad0xd1 S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power) +sii,s35390a 2-wire CMOS real-time clock st-micro,24c256 i2c serial eeprom (24cxx) stm,m41t00 Serial Access TIMEKEEPER stm,m41t62 Serial real-time clock (RTC) with alarm @@ -65,5 +86,6 @@ stm,m41t80 M41T80 - SERIAL ACCESS RTC WITH ALARMS taos,tsl2550 Ambient Light Sensor with SMBUS/Two Wire Serial Interface ti,tsc2003 I2C Touch-Screen Controller ti,tmp102 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface +ti,tmp103 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface ti,tmp275 Digital Temperature Sensor winbond,wpct301 i2c trusted platform module (TPM) diff --git a/Documentation/devicetree/bindings/arm/atmel-adc.txt b/Documentation/devicetree/bindings/iio/adc/at91_adc.txt index d1061469f63d..0f813dec5e08 100644 --- a/Documentation/devicetree/bindings/arm/atmel-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/at91_adc.txt @@ -5,32 +5,35 @@ Required properties: <chip> can be "at91sam9260", "at91sam9g45" or "at91sam9x5" - reg: Should contain ADC registers location and length - interrupts: Should contain the IRQ line for the ADC - - atmel,adc-channels-used: Bitmask of the channels muxed and enable for this + - clock-names: tuple listing input clock names. + Required elements: "adc_clk", "adc_op_clk". + - clocks: phandles to input clocks. + - atmel,adc-channels-used: Bitmask of the channels muxed and enabled for this device - atmel,adc-startup-time: Startup Time of the ADC in microseconds as defined in the datasheet - atmel,adc-vref: Reference voltage in millivolts for the conversions - - atmel,adc-res: List of resolution in bits supported by the ADC. List size + - atmel,adc-res: List of resolutions in bits supported by the ADC. List size must be two at least. - atmel,adc-res-names: Contains one identifier string for each resolution in atmel,adc-res property. "lowres" and "highres" identifiers are required. Optional properties: - - atmel,adc-use-external: Boolean to enable of external triggers + - atmel,adc-use-external-triggers: Boolean to enable the external triggers - atmel,adc-use-res: String corresponding to an identifier from atmel,adc-res-names property. If not specified, the highest resolution will be used. - atmel,adc-sleep-mode: Boolean to enable sleep mode when no conversion - atmel,adc-sample-hold-time: Sample and Hold Time in microseconds - - atmel,adc-ts-wires: Number of touch screen wires. Should be 4 or 5. If this - value is set, then adc driver will enable touch screen + - atmel,adc-ts-wires: Number of touchscreen wires. Should be 4 or 5. If this + value is set, then the adc driver will enable touchscreen support. - NOTE: when adc touch screen enabled, the adc hardware trigger will be - disabled. Since touch screen will occupied the trigger register. + NOTE: when adc touchscreen is enabled, the adc hardware trigger will be + disabled. Since touchscreen will occupy the trigger register. - atmel,adc-ts-pressure-threshold: a pressure threshold for touchscreen. It - make touch detect more precision. - + makes touch detection more precise. + Optional trigger Nodes: - Required properties: * trigger-name: Name of the trigger exposed to the user @@ -41,40 +44,43 @@ Optional trigger Nodes: Examples: adc0: adc@fffb0000 { + #address-cells = <1>; + #size-cells = <0>; compatible = "atmel,at91sam9260-adc"; reg = <0xfffb0000 0x100>; - interrupts = <20 4>; - atmel,adc-channel-base = <0x30>; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&adc_clk>, <&adc_op_clk>; + clock-names = "adc_clk", "adc_op_clk"; atmel,adc-channels-used = <0xff>; - atmel,adc-drdy-mask = <0x10000>; - atmel,adc-num-channels = <8>; atmel,adc-startup-time = <40>; - atmel,adc-status-register = <0x1c>; - atmel,adc-trigger-register = <0x08>; - atmel,adc-use-external; + atmel,adc-use-external-triggers; atmel,adc-vref = <3300>; atmel,adc-res = <8 10>; atmel,adc-res-names = "lowres", "highres"; atmel,adc-use-res = "lowres"; trigger@0 { + reg = <0>; trigger-name = "external-rising"; trigger-value = <0x1>; trigger-external; }; trigger@1 { + reg = <1>; trigger-name = "external-falling"; trigger-value = <0x2>; trigger-external; }; trigger@2 { + reg = <2>; trigger-name = "external-any"; trigger-value = <0x3>; trigger-external; }; trigger@3 { + reg = <3>; trigger-name = "continuous"; trigger-value = <0x6>; }; diff --git a/Documentation/devicetree/bindings/iio/adc/max1027-adc.txt b/Documentation/devicetree/bindings/iio/adc/max1027-adc.txt new file mode 100644 index 000000000000..a8770cc6bcad --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/max1027-adc.txt @@ -0,0 +1,22 @@ +* Maxim 1027/1029/1031 Analog to Digital Converter (ADC) + +Required properties: + - compatible: Should be "maxim,max1027" or "maxim,max1029" or "maxim,max1031" + - reg: SPI chip select number for the device + - interrupt-parent: phandle to the parent interrupt controller + see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + - interrupts: IRQ line for the ADC + see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + +Recommended properties: +- spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: +adc@0 { + compatible = "maxim,max1027"; + reg = <0>; + interrupt-parent = <&gpio5>; + interrupts = <15 IRQ_TYPE_EDGE_RISING>; + spi-max-frequency = <1000000>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt b/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt new file mode 100644 index 000000000000..5d3ec1df226d --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt @@ -0,0 +1,24 @@ +Rockchip Successive Approximation Register (SAR) A/D Converter bindings + +Required properties: +- compatible: Should be "rockchip,saradc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: The interrupt number to the cpu. The interrupt specifier format + depends on the interrupt controller. +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Shall be "saradc" for the converter-clock, and "apb_pclk" for + the peripheral clock. +- vref-supply: The regulator supply ADC reference voltage. +- #io-channel-cells: Should be 1, see ../iio-bindings.txt + +Example: + saradc: saradc@2006c000 { + compatible = "rockchip,saradc"; + reg = <0x2006c000 0x100>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>; + clock-names = "saradc", "apb_pclk"; + #io-channel-cells = <1>; + vref-supply = <&vcc18>; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/twl4030-madc.txt b/Documentation/devicetree/bindings/iio/adc/twl4030-madc.txt new file mode 100644 index 000000000000..6bdd21404b57 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/twl4030-madc.txt @@ -0,0 +1,24 @@ +* TWL4030 Monitoring Analog to Digital Converter (MADC) + +The MADC subsystem in the TWL4030 consists of a 10-bit ADC +combined with a 16-input analog multiplexer. + +Required properties: + - compatible: Should contain "ti,twl4030-madc". + - interrupts: IRQ line for the MADC submodule. + - #io-channel-cells: Should be set to <1>. + +Optional properties: + - ti,system-uses-second-madc-irq: boolean, set if the second madc irq register + should be used, which is intended to be used + by Co-Processors (e.g. a modem). + +Example: + +&twl { + madc { + compatible = "ti,twl4030-madc"; + interrupts = <3>; + #io-channel-cells = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt b/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt new file mode 100644 index 000000000000..1a4a43d5c9ea --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt @@ -0,0 +1,22 @@ +Freescale vf610 Analog to Digital Converter bindings + +The devicetree bindings are for the new ADC driver written for +vf610/i.MX6slx and upward SoCs from Freescale. + +Required properties: +- compatible: Should contain "fsl,vf610-adc" +- reg: Offset and length of the register set for the device +- interrupts: Should contain the interrupt for the device +- clocks: The clock is needed by the ADC controller, ADC clock source is ipg clock. +- clock-names: Must contain "adc", matching entry in the clocks property. +- vref-supply: The regulator supply ADC reference voltage. + +Example: +adc0: adc@4003b000 { + compatible = "fsl,vf610-adc"; + reg = <0x4003b000 0x1000>; + interrupts = <0 53 0x04>; + clocks = <&clks VF610_CLK_ADC0>; + clock-names = "adc"; + vref-supply = <®_vcc_3v3_mcu>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/xilinx-xadc.txt b/Documentation/devicetree/bindings/iio/adc/xilinx-xadc.txt new file mode 100644 index 000000000000..d9ee909d2b78 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/xilinx-xadc.txt @@ -0,0 +1,113 @@ +Xilinx XADC device driver + +This binding document describes the bindings for both of them since the +bindings are very similar. The Xilinx XADC is a ADC that can be found in the +series 7 FPGAs from Xilinx. The XADC has a DRP interface for communication. +Currently two different frontends for the DRP interface exist. One that is only +available on the ZYNQ family as a hardmacro in the SoC portion of the ZYNQ. The +other one is available on all series 7 platforms and is a softmacro with a AXI +interface. This binding document describes the bindings for both of them since +the bindings are very similar. + +Required properties: + - compatible: Should be one of + * "xlnx,zynq-xadc-1.00.a": When using the ZYNQ device + configuration interface to interface to the XADC hardmacro. + * "xlnx,axi-xadc-1.00.a": When using the axi-xadc pcore to + interface to the XADC hardmacro. + - reg: Address and length of the register set for the device + - interrupts: Interrupt for the XADC control interface. + - clocks: When using the ZYNQ this must be the ZYNQ PCAP clock, + when using the AXI-XADC pcore this must be the clock that provides the + clock to the AXI bus interface of the core. + +Optional properties: + - interrupt-parent: phandle to the parent interrupt controller + - xlnx,external-mux: + * "none": No external multiplexer is used, this is the default + if the property is omitted. + * "single": External multiplexer mode is used with one + multiplexer. + * "dual": External multiplexer mode is used with two + multiplexers for simultaneous sampling. + - xlnx,external-mux-channel: Configures which pair of pins is used to + sample data in external mux mode. + Valid values for single external multiplexer mode are: + 0: VP/VN + 1: VAUXP[0]/VAUXN[0] + 2: VAUXP[1]/VAUXN[1] + ... + 16: VAUXP[15]/VAUXN[15] + Valid values for dual external multiplexer mode are: + 1: VAUXP[0]/VAUXN[0] - VAUXP[8]/VAUXN[8] + 2: VAUXP[1]/VAUXN[1] - VAUXP[9]/VAUXN[9] + ... + 8: VAUXP[7]/VAUXN[7] - VAUXP[15]/VAUXN[15] + + This property needs to be present if the device is configured for + external multiplexer mode (either single or dual). If the device is + not using external multiplexer mode the property is ignored. + - xnlx,channels: List of external channels that are connected to the ADC + Required properties: + * #address-cells: Should be 1. + * #size-cells: Should be 0. + + The child nodes of this node represent the external channels which are + connected to the ADC. If the property is no present no external + channels will be assumed to be connected. + + Each child node represents one channel and has the following + properties: + Required properties: + * reg: Pair of pins the the channel is connected to. + 0: VP/VN + 1: VAUXP[0]/VAUXN[0] + 2: VAUXP[1]/VAUXN[1] + ... + 16: VAUXP[15]/VAUXN[15] + Note each channel number should only be used at most + once. + Optional properties: + * xlnx,bipolar: If set the channel is used in bipolar + mode. + + +Examples: + xadc@f8007100 { + compatible = "xlnx,zynq-xadc-1.00.a"; + reg = <0xf8007100 0x20>; + interrupts = <0 7 4>; + interrupt-parent = <&gic>; + clocks = <&pcap_clk>; + + xlnx,channels { + #address-cells = <1>; + #size-cells = <0>; + channel@0 { + reg = <0>; + }; + channel@1 { + reg = <1>; + }; + channel@8 { + reg = <8>; + }; + }; + }; + + xadc@43200000 { + compatible = "xlnx,axi-xadc-1.00.a"; + reg = <0x43200000 0x1000>; + interrupts = <0 53 4>; + interrupt-parent = <&gic>; + clocks = <&fpga1_clk>; + + xlnx,channels { + #address-cells = <1>; + #size-cells = <0>; + channel@0 { + reg = <0>; + xlnx,bipolar; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/dac/max5821.txt b/Documentation/devicetree/bindings/iio/dac/max5821.txt new file mode 100644 index 000000000000..54276ce8c971 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/max5821.txt @@ -0,0 +1,14 @@ +Maxim max5821 DAC device driver + +Required properties: + - compatible: Must be "maxim,max5821" + - reg: Should contain the DAC I2C address + - vref-supply: Phandle to the vref power supply + +Example: + + max5821@38 { + compatible = "maxim,max5821"; + reg = <0x38>; + vref-supply = <®_max5821>; + }; diff --git a/Documentation/devicetree/bindings/iio/magnetometer/hmc5843.txt b/Documentation/devicetree/bindings/iio/magnetometer/hmc5843.txt index 90d5f34db04e..8e191eef014e 100644 --- a/Documentation/devicetree/bindings/iio/magnetometer/hmc5843.txt +++ b/Documentation/devicetree/bindings/iio/magnetometer/hmc5843.txt @@ -3,6 +3,10 @@ Required properties: - compatible : should be "honeywell,hmc5843" + Other models which are supported with driver are: + "honeywell,hmc5883" + "honeywell,hmc5883l" + "honeywell,hmc5983" - reg : the I2C address of the magnetometer - typically 0x1e Optional properties: diff --git a/Documentation/devicetree/bindings/iio/proximity/as3935.txt b/Documentation/devicetree/bindings/iio/proximity/as3935.txt new file mode 100644 index 000000000000..ae23dd8da736 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/proximity/as3935.txt @@ -0,0 +1,28 @@ +Austrian Microsystems AS3935 Franklin lightning sensor device driver + +Required properties: + - compatible: must be "ams,as3935" + - reg: SPI chip select number for the device + - spi-cpha: SPI Mode 1. Refer to spi/spi-bus.txt for generic SPI + slave node bindings. + - interrupt-parent : should be the phandle for the interrupt controller + - interrupts : the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic + interrupt client node bindings. + +Optional properties: + - ams,tuning-capacitor-pf: Calibration tuning capacitor stepping + value 0 - 120pF. This will require using the calibration data from + the manufacturer. + +Example: + +as3935@0 { + compatible = "ams,as3935"; + reg = <0>; + spi-cpha; + interrupt-parent = <&gpio1>; + interrupts = <16 1>; + ams,tuning-capacitor-pf = <80>; +}; diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt new file mode 100644 index 000000000000..a7a0a15913ad --- /dev/null +++ b/Documentation/devicetree/bindings/iio/st-sensors.txt @@ -0,0 +1,54 @@ +STMicroelectronics MEMS sensors + +The STMicroelectronics sensor devices are pretty straight-forward I2C or +SPI devices, all sharing the same device tree descriptions no matter what +type of sensor it is. + +Required properties: +- compatible: see the list of valid compatible strings below +- reg: the I2C or SPI address the device will respond to + +Optional properties: +- vdd-supply: an optional regulator that needs to be on to provide VDD + power to the sensor. +- vddio-supply: an optional regulator that needs to be on to provide the + VDD IO power to the sensor. +- st,drdy-int-pin: the pin on the package that will be used to signal + "data ready" (valid values: 1 or 2). This property is not configurable + on all sensors. + +Sensors may also have applicable pin control settings, those use the +standard bindings from pinctrl/pinctrl-bindings.txt. + +Valid compatible strings: + +Accelerometers: +- st,lsm303dlh-accel +- st,lsm303dlhc-accel +- st,lis3dh-accel +- st,lsm330d-accel +- st,lsm330dl-accel +- st,lsm330dlc-accel +- st,lis331dlh-accel +- st,lsm303dl-accel +- st,lsm303dlm-accel +- st,lsm330-accel + +Gyroscopes: +- st,l3g4200d-gyro +- st,lsm330d-gyro +- st,lsm330dl-gyro +- st,lsm330dlc-gyro +- st,l3gd20-gyro +- st,l3g4is-gyro +- st,lsm330-gyro + +Magnetometers: +- st,lsm303dlhc-magn +- st,lsm303dlm-magn +- st,lis3mdl-magn + +Pressure sensors: +- st,lps001wp-press +- st,lps25h-press +- st,lps331ap-press diff --git a/Documentation/devicetree/bindings/input/atmel,maxtouch.txt b/Documentation/devicetree/bindings/input/atmel,maxtouch.txt new file mode 100644 index 000000000000..1852906517ab --- /dev/null +++ b/Documentation/devicetree/bindings/input/atmel,maxtouch.txt @@ -0,0 +1,32 @@ +Atmel maXTouch touchscreen/touchpad + +Required properties: +- compatible: + atmel,maxtouch + +- reg: The I2C address of the device + +- interrupts: The sink for the touchpad's IRQ output + See ../interrupt-controller/interrupts.txt + +Optional properties for main touchpad device: + +- linux,gpio-keymap: When enabled, the SPT_GPIOPWN_T19 object sends messages + on GPIO bit changes. An array of up to 8 entries can be provided + indicating the Linux keycode mapped to each bit of the status byte, + starting at the LSB. Linux keycodes are defined in + <dt-bindings/input/input.h>. + + Note: the numbering of the GPIOs and the bit they start at varies between + maXTouch devices. You must either refer to the documentation, or + experiment to determine which bit corresponds to which input. Use + KEY_RESERVED for unused padding values. + +Example: + + touch@4b { + compatible = "atmel,maxtouch"; + reg = <0x4b>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_LEVEL_LOW>; + }; diff --git a/Documentation/devicetree/bindings/input/cap1106.txt b/Documentation/devicetree/bindings/input/cap1106.txt new file mode 100644 index 000000000000..4b463904cba0 --- /dev/null +++ b/Documentation/devicetree/bindings/input/cap1106.txt @@ -0,0 +1,53 @@ +Device tree bindings for Microchip CAP1106, 6 channel capacitive touch sensor + +The node for this driver must be a child of a I2C controller node, as the +device communication via I2C only. + +Required properties: + + compatible: Must be "microchip,cap1106" + + reg: The I2C slave address of the device. + Only 0x28 is valid. + + interrupts: Property describing the interrupt line the + device's ALERT#/CM_IRQ# pin is connected to. + The device only has one interrupt source. + +Optional properties: + + autorepeat: Enables the Linux input system's autorepeat + feature on the input device. + + microchip,sensor-gain: Defines the gain of the sensor circuitry. This + effectively controls the sensitivity, as a + smaller delta capacitance is required to + generate the same delta count values. + Valid values are 1, 2, 4, and 8. + By default, a gain of 1 is set. + + linux,keycodes: Specifies an array of numeric keycode values to + be used for the channels. If this property is + omitted, KEY_A, KEY_B, etc are used as + defaults. The array must have exactly six + entries. + +Example: + +i2c_controller { + cap1106@28 { + compatible = "microchip,cap1106"; + interrupt-parent = <&gpio1>; + interrupts = <0 0>; + reg = <0x28>; + autorepeat; + microchip,sensor-gain = <2>; + + linux,keycodes = <103 /* KEY_UP */ + 106 /* KEY_RIGHT */ + 108 /* KEY_DOWN */ + 105 /* KEY_LEFT */ + 109 /* KEY_PAGEDOWN */ + 104>; /* KEY_PAGEUP */ + }; +} diff --git a/Documentation/devicetree/bindings/input/clps711x-keypad.txt b/Documentation/devicetree/bindings/input/clps711x-keypad.txt new file mode 100644 index 000000000000..e68d2bbc6c07 --- /dev/null +++ b/Documentation/devicetree/bindings/input/clps711x-keypad.txt @@ -0,0 +1,27 @@ +* Cirrus Logic CLPS711X matrix keypad device tree bindings + +Required Properties: +- compatible: Shall contain "cirrus,clps711x-keypad". +- row-gpios: List of GPIOs used as row lines. +- poll-interval: Poll interval time in milliseconds. +- linux,keymap: The definition can be found at + bindings/input/matrix-keymap.txt. + +Optional Properties: +- autorepeat: Enable autorepeat feature. + +Example: + keypad { + compatible = "cirrus,ep7312-keypad", "cirrus,clps711x-keypad"; + autorepeat; + poll-interval = <120>; + row-gpios = <&porta 0 0>, + <&porta 1 0>; + + linux,keymap = < + MATRIX_KEY(0, 0, KEY_UP) + MATRIX_KEY(0, 1, KEY_DOWN) + MATRIX_KEY(1, 0, KEY_LEFT) + MATRIX_KEY(1, 1, KEY_RIGHT) + >; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio_keys.txt b/Documentation/devicetree/bindings/input/gpio-keys.txt index 5c2c02140a62..5c2c02140a62 100644 --- a/Documentation/devicetree/bindings/gpio/gpio_keys.txt +++ b/Documentation/devicetree/bindings/input/gpio-keys.txt diff --git a/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt b/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt new file mode 100644 index 000000000000..7d8cb92831d7 --- /dev/null +++ b/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt @@ -0,0 +1,89 @@ +Qualcomm PM8xxx PMIC Keypad + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,pm8058-keypad" + "qcom,pm8921-keypad" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: address of keypad control register + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: the first interrupt specifies the key sense interrupt + and the second interrupt specifies the key stuck interrupt. + The format of the specifier is defined by the binding + document describing the node's interrupt parent. + +- linux,keymap: + Usage: required + Value type: <prop-encoded-array> + Definition: the linux keymap. More information can be found in + input/matrix-keymap.txt. + +- linux,keypad-no-autorepeat: + Usage: optional + Value type: <bool> + Definition: don't enable autorepeat feature. + +- linux,keypad-wakeup: + Usage: optional + Value type: <bool> + Definition: use any event on keypad as wakeup event. + +- keypad,num-rows: + Usage: required + Value type: <u32> + Definition: number of rows in the keymap. More information can be found + in input/matrix-keymap.txt. + +- keypad,num-columns: + Usage: required + Value type: <u32> + Definition: number of columns in the keymap. More information can be + found in input/matrix-keymap.txt. + +- debounce: + Usage: optional + Value type: <u32> + Definition: time in microseconds that key must be pressed or release + for key sense interrupt to trigger. + +- scan-delay: + Usage: optional + Value type: <u32> + Definition: time in microseconds to pause between successive scans + of the matrix array. + +- row-hold: + Usage: optional + Value type: <u32> + Definition: time in nanoseconds to pause between scans of each row in + the matrix array. + +EXAMPLE + + keypad@148 { + compatible = "qcom,pm8921-keypad"; + reg = <0x148>; + interrupt-parent = <&pmicintc>; + interrupts = <74 1>, <75 1>; + linux,keymap = < + MATRIX_KEY(0, 0, KEY_VOLUMEUP) + MATRIX_KEY(0, 1, KEY_VOLUMEDOWN) + MATRIX_KEY(0, 2, KEY_CAMERA_FOCUS) + MATRIX_KEY(0, 3, KEY_CAMERA) + >; + keypad,num-rows = <1>; + keypad,num-columns = <5>; + debounce = <15>; + scan-delay = <32>; + row-hold = <91500>; + }; diff --git a/Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt b/Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt new file mode 100644 index 000000000000..588536cc96ed --- /dev/null +++ b/Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt @@ -0,0 +1,46 @@ +Qualcomm PM8xxx PMIC Power Key + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,pm8058-pwrkey" + "qcom,pm8921-pwrkey" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: address of power key control register + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: the first interrupt specifies the key release interrupt + and the second interrupt specifies the key press interrupt. + The format of the specifier is defined by the binding + document describing the node's interrupt parent. + +- debounce: + Usage: optional + Value type: <u32> + Definition: time in microseconds that key must be pressed or release + for state change interrupt to trigger. + +- pull-up: + Usage: optional + Value type: <empty> + Definition: presence of this property indicates that the KPDPWR_N pin + should be configured for pull up. + +EXAMPLE + + pwrkey@1c { + compatible = "qcom,pm8921-pwrkey"; + reg = <0x1c>; + interrupt-parent = <&pmicintc>; + interrupts = <50 1>, <51 1>; + debounce = <15625>; + pull-up; + }; diff --git a/Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.txt b/Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.txt new file mode 100644 index 000000000000..4ed467b1e402 --- /dev/null +++ b/Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.txt @@ -0,0 +1,22 @@ +Qualcomm PM8xxx PMIC Vibrator + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,pm8058-vib" + "qcom,pm8921-vib" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: address of vibration control register + +EXAMPLE + + vibrator@4a { + compatible = "qcom,pm8058-vib"; + reg = <0x4a>; + }; diff --git a/Documentation/devicetree/bindings/input/st-keyscan.txt b/Documentation/devicetree/bindings/input/st-keyscan.txt new file mode 100644 index 000000000000..51eb428e5c85 --- /dev/null +++ b/Documentation/devicetree/bindings/input/st-keyscan.txt @@ -0,0 +1,60 @@ +* ST Keyscan controller Device Tree bindings + +The ST keyscan controller Device Tree binding is based on the +matrix-keymap. + +Required properties: +- compatible: "st,sti-keyscan" + +- reg: Register base address and size of st-keyscan controller. + +- interrupts: Interrupt number for the st-keyscan controller. + +- clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. + +- pinctrl: Should specify pin control groups used for this controller. + See ../pinctrl/pinctrl-bindings.txt for details. + +- linux,keymap: The keymap for keys as described in the binding document + devicetree/bindings/input/matrix-keymap.txt. + +- keypad,num-rows: Number of row lines connected to the keypad controller. + +- keypad,num-columns: Number of column lines connected to the keypad + controller. + +Optional property: +- st,debounce_us: Debouncing interval time in microseconds + +Example: + +keyscan: keyscan@fe4b0000 { + compatible = "st,sti-keyscan"; + reg = <0xfe4b0000 0x2000>; + interrupts = <GIC_SPI 212 IRQ_TYPE_NONE>; + clocks = <&CLK_SYSIN>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_keyscan>; + + keypad,num-rows = <4>; + keypad,num-columns = <4>; + st,debounce_us = <5000>; + + linux,keymap = < MATRIX_KEY(0x00, 0x00, KEY_F13) + MATRIX_KEY(0x00, 0x01, KEY_F9) + MATRIX_KEY(0x00, 0x02, KEY_F5) + MATRIX_KEY(0x00, 0x03, KEY_F1) + MATRIX_KEY(0x01, 0x00, KEY_F14) + MATRIX_KEY(0x01, 0x01, KEY_F10) + MATRIX_KEY(0x01, 0x02, KEY_F6) + MATRIX_KEY(0x01, 0x03, KEY_F2) + MATRIX_KEY(0x02, 0x00, KEY_F15) + MATRIX_KEY(0x02, 0x01, KEY_F11) + MATRIX_KEY(0x02, 0x02, KEY_F7) + MATRIX_KEY(0x02, 0x03, KEY_F3) + MATRIX_KEY(0x03, 0x00, KEY_F16) + MATRIX_KEY(0x03, 0x01, KEY_F12) + MATRIX_KEY(0x03, 0x02, KEY_F8) + MATRIX_KEY(0x03, 0x03, KEY_F4) >; + }; diff --git a/Documentation/devicetree/bindings/input/ti,drv260x.txt b/Documentation/devicetree/bindings/input/ti,drv260x.txt new file mode 100644 index 000000000000..ee09c8f4474a --- /dev/null +++ b/Documentation/devicetree/bindings/input/ti,drv260x.txt @@ -0,0 +1,50 @@ +* Texas Instruments - drv260x Haptics driver family + +Required properties: + - compatible - One of: + "ti,drv2604" - DRV2604 + "ti,drv2605" - DRV2605 + "ti,drv2605l" - DRV2605L + - reg - I2C slave address + - vbat-supply - Required supply regulator + - mode - Power up mode of the chip (defined in include/dt-bindings/input/ti-drv260x.h) + DRV260X_LRA_MODE - Linear Resonance Actuator mode (Piezoelectric) + DRV260X_LRA_NO_CAL_MODE - This is a LRA Mode but there is no calibration + sequence during init. And the device is configured for real + time playback mode (RTP mode). + DRV260X_ERM_MODE - Eccentric Rotating Mass mode (Rotary vibrator) + - library-sel - These are ROM based waveforms pre-programmed into the IC. + This should be set to set the library to use at power up. + (defined in include/dt-bindings/input/ti-drv260x.h) + DRV260X_LIB_EMPTY - Do not use a pre-programmed library + DRV260X_ERM_LIB_A - Pre-programmed Library + DRV260X_ERM_LIB_B - Pre-programmed Library + DRV260X_ERM_LIB_C - Pre-programmed Library + DRV260X_ERM_LIB_D - Pre-programmed Library + DRV260X_ERM_LIB_E - Pre-programmed Library + DRV260X_ERM_LIB_F - Pre-programmed Library + DRV260X_LIB_LRA - Pre-programmed LRA Library + +Optional properties: + - enable-gpio - gpio pin to enable/disable the device. + - vib-rated-mv - The rated voltage of the actuator in millivolts. + If this is not set then the value will be defaulted to + 3.2 v. + - vib-overdrive-mv - The overdrive voltage of the actuator in millivolts. + If this is not set then the value will be defaulted to + 3.2 v. +Example: + +haptics: haptics@5a { + compatible = "ti,drv2605l"; + reg = <0x5a>; + vbat-supply = <&vbat>; + enable-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>; + mode = <DRV260X_LRA_MODE>; + library-sel = <DRV260X_LIB_LRA>; + vib-rated-mv = <3200>; + vib-overdriver-mv = <3200>; +} + +For more product information please see the link below: +http://www.ti.com/product/drv2605 diff --git a/Documentation/devicetree/bindings/input/ti,drv2667.txt b/Documentation/devicetree/bindings/input/ti,drv2667.txt new file mode 100644 index 000000000000..996382cf994a --- /dev/null +++ b/Documentation/devicetree/bindings/input/ti,drv2667.txt @@ -0,0 +1,17 @@ +* Texas Instruments - drv2667 Haptics driver + +Required properties: + - compatible - "ti,drv2667" - DRV2667 + - reg - I2C slave address + - vbat-supply - Required supply regulator + +Example: + +haptics: haptics@59 { + compatible = "ti,drv2667"; + reg = <0x59>; + vbat-supply = <&vbat>; +}; + +For more product information please see the link below: +http://www.ti.com/product/drv2667 diff --git a/Documentation/devicetree/bindings/input/ti,palmas-pwrbutton.txt b/Documentation/devicetree/bindings/input/ti,palmas-pwrbutton.txt new file mode 100644 index 000000000000..a3dde8c30e67 --- /dev/null +++ b/Documentation/devicetree/bindings/input/ti,palmas-pwrbutton.txt @@ -0,0 +1,36 @@ +Texas Instruments Palmas family power button module + +This module is part of the Palmas family of PMICs. For more details +about the whole chip see: +Documentation/devicetree/bindings/mfd/palmas.txt. + +This module provides a simple power button event via an Interrupt. + +Required properties: +- compatible: should be one of the following + - "ti,palmas-pwrbutton": For Palmas compatible power on button +- interrupt-parent: Parent interrupt device, must be handle of palmas node. +- interrupts: Interrupt number of power button submodule on device. + +Optional Properties: + +- ti,palmas-long-press-seconds: Duration in seconds which the power + button should be kept pressed for Palmas to power off automatically. + NOTE: This depends on OTP support and POWERHOLD signal configuration + on platform. Valid values are 6, 8, 10 and 12. +- ti,palmas-pwron-debounce-milli-seconds: Duration in milliseconds + which the power button should be kept pressed for Palmas to register + a press for debouncing purposes. NOTE: This depends on specific + Palmas variation capability. Valid values are 15, 100, 500 and 1000. + +Example: + +&palmas { + palmas_pwr_button: pwrbutton { + compatible = "ti,palmas-pwrbutton"; + interrupt-parent = <&tps659038>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + ti,palmas-long-press-seconds = <12>; + ti,palmas-pwron-debounce-milli-seconds = <15>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt new file mode 100644 index 000000000000..76db96704a60 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt @@ -0,0 +1,55 @@ +FocalTech EDT-FT5x06 Polytouch driver +===================================== + +There are 3 variants of the chip for various touch panel sizes +FT5206GE1 2.8" .. 3.8" +FT5306DE4 4.3" .. 7" +FT5406EE8 7" .. 8.9" + +The software interface is identical for all those chips, so that +currently there is no need for the driver to distinguish between the +different chips. Nevertheless distinct compatible strings are used so +that a distinction can be added if necessary without changing the DT +bindings. + + +Required properties: + - compatible: "edt,edt-ft5206" + or: "edt,edt-ft5306" + or: "edt,edt-ft5406" + + - reg: I2C slave address of the chip (0x38) + - interrupt-parent: a phandle pointing to the interrupt controller + serving the interrupt for this chip + - interrupts: interrupt specification for the touchdetect + interrupt + +Optional properties: + - reset-gpios: GPIO specification for the RESET input + - wake-gpios: GPIO specification for the WAKE input + + - pinctrl-names: should be "default" + - pinctrl-0: a phandle pointing to the pin settings for the + control gpios + + - threshold: allows setting the "click"-threshold in the range + from 20 to 80. + + - gain: allows setting the sensitivity in the range from 0 to + 31. Note that lower values indicate higher + sensitivity. + + - offset: allows setting the edge compensation in the range from + 0 to 31. + +Example: + polytouch: edt-ft5x06@38 { + compatible = "edt,edt-ft5406", "edt,edt-ft5x06"; + reg = <0x38>; + pinctrl-names = "default"; + pinctrl-0 = <&edt_ft5x06_pins>; + interrupt-parent = <&gpio2>; + interrupts = <5 0>; + reset-gpios = <&gpio2 6 1>; + wake-gpios = <&gpio4 9 0>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt b/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt new file mode 100644 index 000000000000..6e551090f465 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt @@ -0,0 +1,26 @@ +* Pixcir I2C touchscreen controllers + +Required properties: +- compatible: must be "pixcir,pixcir_ts" or "pixcir,pixcir_tangoc" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected +- attb-gpio: GPIO connected to the ATTB line of the chip +- touchscreen-size-x: horizontal resolution of touchscreen (in pixels) +- touchscreen-size-y: vertical resolution of touchscreen (in pixels) + +Example: + + i2c@00000000 { + /* ... */ + + pixcir_ts@5c { + compatible = "pixcir,pixcir_ts"; + reg = <0x5c>; + interrupts = <2 0>; + attb-gpio = <&gpf 2 0 2>; + touchscreen-size-x = <800>; + touchscreen-size-y = <600>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/sun4i.txt b/Documentation/devicetree/bindings/input/touchscreen/sun4i.txt new file mode 100644 index 000000000000..aef57791f40b --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/sun4i.txt @@ -0,0 +1,20 @@ +sun4i resistive touchscreen controller +-------------------------------------- + +Required properties: + - compatible: "allwinner,sun4i-a10-ts" + - reg: mmio address range of the chip + - interrupts: interrupt to which the chip is connected + +Optional properties: + - allwinner,ts-attached: boolean indicating that an actual touchscreen is + attached to the controller + +Example: + + rtp: rtp@01c25000 { + compatible = "allwinner,sun4i-a10-ts"; + reg = <0x01c25000 0x100>; + interrupts = <29>; + allwinner,ts-attached; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt new file mode 100644 index 000000000000..d8e06163c54e --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt @@ -0,0 +1,27 @@ +General Touchscreen Properties: + +Optional properties for Touchscreens: + - touchscreen-size-x : horizontal resolution of touchscreen + (in pixels) + - touchscreen-size-y : vertical resolution of touchscreen + (in pixels) + - touchscreen-max-pressure : maximum reported pressure (arbitrary range + dependent on the controller) + - touchscreen-fuzz-x : horizontal noise value of the absolute input + device (in pixels) + - touchscreen-fuzz-y : vertical noise value of the absolute input + device (in pixels) + - touchscreen-fuzz-pressure : pressure noise value of the absolute input + device (arbitrary range dependent on the + controller) + - touchscreen-inverted-x : X axis is inverted (boolean) + - touchscreen-inverted-y : Y axis is inverted (boolean) + +Deprecated properties for Touchscreens: + - x-size : deprecated name for touchscreen-size-x + - y-size : deprecated name for touchscreen-size-y + - moving-threshold : deprecated name for a combination of + touchscreen-fuzz-x and touchscreen-fuzz-y + - contact-threshold : deprecated name for touchscreen-fuzz-pressure + - x-invert : deprecated name for touchscreen-inverted-x + - y-invert : deprecated name for touchscreen-inverted-y diff --git a/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt b/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt new file mode 100644 index 000000000000..4b641c7bf1c2 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt @@ -0,0 +1,42 @@ +* Texas Instruments tsc2005 touchscreen controller + +Required properties: + - compatible : "ti,tsc2005" + - reg : SPI device address + - spi-max-frequency : Maximal SPI speed + - interrupts : IRQ specifier + - reset-gpios : GPIO specifier + - vio-supply : Regulator specifier + +Optional properties: + - ti,x-plate-ohms : integer, resistance of the touchscreen's X plates + in ohm (defaults to 280) + - ti,esd-recovery-timeout-ms : integer, if the touchscreen does not respond after + the configured time (in milli seconds), the driver + will reset it. This is disabled by default. + - properties defined in touchscreen.txt + +Example: + +&mcspi1 { + tsc2005@0 { + compatible = "ti,tsc2005"; + spi-max-frequency = <6000000>; + reg = <0>; + + vio-supply = <&vio>; + + reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104 */ + interrupts-extended = <&gpio4 4 IRQ_TYPE_EDGE_RISING>; /* 100 */ + + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + touchscreen-fuzz-pressure = <2>; + touchscreen-max-x = <4096>; + touchscreen-max-y = <4096>; + touchscreen-max-pressure = <2048>; + + ti,x-plate-ohms = <280>; + ti,esd-recovery-timeout-ms = <8000>; + }; +} diff --git a/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt b/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt new file mode 100644 index 000000000000..80c37df940a7 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt @@ -0,0 +1,34 @@ +* Neonode infrared touchscreen controller + +Required properties: +- compatible: must be "neonode,zforce" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected +- gpios: gpios the chip is connected to + first one is the interrupt gpio and second one the reset gpio +- x-size: horizontal resolution of touchscreen +- y-size: vertical resolution of touchscreen + +Optional properties: +- vdd-supply: Regulator controlling the controller supply + +Example: + + i2c@00000000 { + /* ... */ + + zforce_ts@50 { + compatible = "neonode,zforce"; + reg = <0x50>; + interrupts = <2 0>; + vdd-supply = <®_zforce_vdd>; + + gpios = <&gpio5 6 0>, /* INT */ + <&gpio5 9 0>; /* RST */ + + x-size = <800>; + y-size = <600>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun4i-ic.txt b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun4i-ic.txt index 32cec4b26cd0..b290ca150d30 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun4i-ic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun4i-ic.txt @@ -2,7 +2,7 @@ Allwinner Sunxi Interrupt Controller Required properties: -- compatible : should be "allwinner,sun4i-ic" +- compatible : should be "allwinner,sun4i-a10-ic" - reg : Specifies base physical address and size of the registers. - interrupt-controller : Identifies the node as an interrupt controller - #interrupt-cells : Specifies the number of cells needed to encode an @@ -11,7 +11,7 @@ Required properties: Example: intc: interrupt-controller { - compatible = "allwinner,sun4i-ic"; + compatible = "allwinner,sun4i-a10-ic"; reg = <0x01c20400 0x400>; interrupt-controller; #interrupt-cells = <1>; diff --git a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun67i-sc-nmi.txt b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun67i-sc-nmi.txt new file mode 100644 index 000000000000..d1c5cdabc3e0 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun67i-sc-nmi.txt @@ -0,0 +1,27 @@ +Allwinner Sunxi NMI Controller +============================== + +Required properties: + +- compatible : should be "allwinner,sun7i-a20-sc-nmi" or + "allwinner,sun6i-a31-sc-nmi" +- reg : Specifies base physical address and size of the registers. +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value shall be 2. The first cell is the IRQ number, the + second cell the trigger type as defined in interrupt.txt in this directory. +- interrupt-parent: Specifies the parent interrupt controller. +- interrupts: Specifies the interrupt line (NMI) which is handled by + the interrupt controller in the parent controller's notation. This value + shall be the NMI. + +Example: + +sc-nmi-intc@01c00030 { + compatible = "allwinner,sun7i-a20-sc-nmi"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x01c00030 0x0c>; + interrupt-parent = <&gic>; + interrupts = <0 0 4>; +}; diff --git a/Documentation/devicetree/bindings/arm/atmel-aic.txt b/Documentation/devicetree/bindings/interrupt-controller/atmel,aic.txt index 2742e9cfd6b1..f292917fa00d 100644 --- a/Documentation/devicetree/bindings/arm/atmel-aic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/atmel,aic.txt @@ -2,7 +2,7 @@ Required properties: - compatible: Should be "atmel,<chip>-aic" - <chip> can be "at91rm9200" or "sama5d3" + <chip> can be "at91rm9200", "sama5d3" or "sama5d4" - interrupt-controller: Identifies the node as an interrupt controller. - interrupt-parent: For single AIC system, it is an empty property. - #interrupt-cells: The number of cells to define the interrupts. It should be 3. diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt new file mode 100644 index 000000000000..ff812a8a82bc --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt @@ -0,0 +1,86 @@ +Broadcom BCM7120-style Level 2 interrupt controller + +This interrupt controller hardware is a second level interrupt controller that +is hooked to a parent interrupt controller: e.g: ARM GIC for ARM-based +platforms. It can be found on BCM7xxx products starting with BCM7120. + +Such an interrupt controller has the following hardware design: + +- outputs multiple interrupts signals towards its interrupt controller parent + +- controls how some of the interrupts will be flowing, whether they will + directly output an interrupt signal towards the interrupt controller parent, + or if they will output an interrupt signal at this 2nd level interrupt + controller, in particular for UARTs + +- not all 32-bits within the interrupt controller actually map to an interrupt + +The typical hardware layout for this controller is represented below: + +2nd level interrupt line Outputs for the parent controller (e.g: ARM GIC) + +0 -----[ MUX ] ------------|==========> GIC interrupt 75 + \-----------\ + | +1 -----[ MUX ] --------)---|==========> GIC interrupt 76 + \------------| + | +2 -----[ MUX ] --------)---|==========> GIC interrupt 77 + \------------| + | +3 ---------------------| +4 ---------------------| +5 ---------------------| +7 ---------------------|---|===========> GIC interrupt 66 +9 ---------------------| +10 --------------------| +11 --------------------/ + +6 ------------------------\ + |===========> GIC interrupt 64 +8 ------------------------/ + +12 ........................ X +13 ........................ X (not connected) +.. +31 ........................ X + +Required properties: + +- compatible: should be "brcm,bcm7120-l2-intc" +- reg: specifies the base physical address and size of the registers +- interrupt-controller: identifies the node as an interrupt controller +- #interrupt-cells: specifies the number of cells needed to encode an interrupt + source, should be 1. +- interrupt-parent: specifies the phandle to the parent interrupt controller + this one is cascaded from +- interrupts: specifies the interrupt line(s) in the interrupt-parent controller + node, valid values depend on the type of parent interrupt controller +- brcm,int-map-mask: 32-bits bit mask describing how many and which interrupts + are wired to this 2nd level interrupt controller, and how they match their + respective interrupt parents. Should match exactly the number of interrupts + specified in the 'interrupts' property. + +Optional properties: + +- brcm,irq-can-wake: if present, this means the L2 controller can be used as a + wakeup source for system suspend/resume. + +- brcm,int-fwd-mask: if present, a 32-bits bit mask to configure for the + interrupts which have a mux gate, typically UARTs. Setting these bits will + make their respective interrupts outputs bypass this 2nd level interrupt + controller completely, it completely transparent for the interrupt controller + parent + +Example: + +irq0_intc: interrupt-controller@f0406800 { + compatible = "brcm,bcm7120-l2-intc"; + interrupt-parent = <&intc>; + #interrupt-cells = <1>; + reg = <0xf0406800 0x8>; + interrupt-controller; + interrupts = <0x0 0x42 0x0>, <0x0 0x40 0x0>; + brcm,int-map-mask = <0xeb8>, <0x140>; + brcm,int-fwd-mask = <0x7>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,l2-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,l2-intc.txt new file mode 100644 index 000000000000..448273a30a11 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,l2-intc.txt @@ -0,0 +1,29 @@ +Broadcom Generic Level 2 Interrupt Controller + +Required properties: + +- compatible: should be "brcm,l2-intc" +- reg: specifies the base physical address and size of the registers +- interrupt-controller: identifies the node as an interrupt controller +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. Should be 1. +- interrupt-parent: specifies the phandle to the parent interrupt controller + this controller is cacaded from +- interrupts: specifies the interrupt line in the interrupt-parent irq space + to be used for cascading + +Optional properties: + +- brcm,irq-can-wake: If present, this means the L2 controller can be used as a + wakeup source for system suspend/resume. + +Example: + +hif_intr2_intc: interrupt-controller@f0441000 { + compatible = "brcm,l2-intc"; + reg = <0xf0441000 0x30>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&intc>; + interrupts = <0x0 0x20 0x0>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/cirrus,clps711x-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/cirrus,clps711x-intc.txt new file mode 100644 index 000000000000..759339c34e4f --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/cirrus,clps711x-intc.txt @@ -0,0 +1,41 @@ +Cirrus Logic CLPS711X Interrupt Controller + +Required properties: + +- compatible: Should be "cirrus,clps711x-intc". +- reg: Specifies base physical address of the registers set. +- interrupt-controller: Identifies the node as an interrupt controller. +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt source. The value shall be 1. + +The interrupt sources are as follows: +ID Name Description +--------------------------- +1: BLINT Battery low (FIQ) +3: MCINT Media changed (FIQ) +4: CSINT CODEC sound +5: EINT1 External 1 +6: EINT2 External 2 +7: EINT3 External 3 +8: TC1OI TC1 under flow +9: TC2OI TC2 under flow +10: RTCMI RTC compare match +11: TINT 64Hz tick +12: UTXINT1 UART1 transmit FIFO half empty +13: URXINT1 UART1 receive FIFO half full +14: UMSINT UART1 modem status changed +15: SSEOTI SSI1 end of transfer +16: KBDINT Keyboard +17: SS2RX SSI2 receive FIFO half or greater full +18: SS2TX SSI2 transmit FIFO less than half empty +28: UTXINT2 UART2 transmit FIFO half empty +29: URXINT2 UART2 receive FIFO half full +32: DAIINT DAI interface (FIQ) + +Example: + intc: interrupt-controller { + compatible = "cirrus,clps711x-intc"; + reg = <0x80000000 0x4000>; + interrupt-controller; + #interrupt-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt b/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt index 1486497a24c1..8a3c40829899 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt @@ -4,11 +4,13 @@ Specifying interrupt information for devices 1) Interrupt client nodes ------------------------- -Nodes that describe devices which generate interrupts must contain an either an -"interrupts" property or an "interrupts-extended" property. These properties -contain a list of interrupt specifiers, one per output interrupt. The format of -the interrupt specifier is determined by the interrupt controller to which the -interrupts are routed; see section 2 below for details. +Nodes that describe devices which generate interrupts must contain an +"interrupts" property, an "interrupts-extended" property, or both. If both are +present, the latter should take precedence; the former may be provided simply +for compatibility with software that does not recognize the latter. These +properties contain a list of interrupt specifiers, one per output interrupt. The +format of the interrupt specifier is determined by the interrupt controller to +which the interrupts are routed; see section 2 below for details. Example: interrupt-parent = <&intc1>; @@ -28,10 +30,6 @@ should only be used when a device has multiple interrupt parents. Example: interrupts-extended = <&intc1 5 1>, <&intc2 1 0>; -A device node may contain either "interrupts" or "interrupts-extended", but not -both. If both properties are present, then the operating system should log an -error and use only the data in "interrupts". - 2) Interrupt controller nodes ----------------------------- diff --git a/Documentation/devicetree/bindings/interrupt-controller/lsi,zevio-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/lsi,zevio-intc.txt new file mode 100644 index 000000000000..aee38e7c13e7 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/lsi,zevio-intc.txt @@ -0,0 +1,18 @@ +TI-NSPIRE interrupt controller + +Required properties: +- compatible: Compatible property value should be "lsi,zevio-intc". + +- reg: Physical base address of the controller and length of memory mapped + region. + +- interrupt-controller : Identifies the node as an interrupt controller + +Example: + +interrupt-controller { + compatible = "lsi,zevio-intc"; + interrupt-controller; + reg = <0xDC000000 0x1000>; + #interrupt-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/arm/armada-370-xp-mpic.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,armada-370-xp-mpic.txt index d74091a8a3bf..5fc03134a999 100644 --- a/Documentation/devicetree/bindings/arm/armada-370-xp-mpic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/marvell,armada-370-xp-mpic.txt @@ -1,4 +1,4 @@ -Marvell Armada 370 and Armada XP Interrupt Controller +Marvell Armada 370, 375, 38x, XP Interrupt Controller ----------------------------------------------------- Required properties: @@ -16,7 +16,13 @@ Required properties: automatically map to the interrupt controller registers of the current CPU) +Optional properties: +- interrupts: If defined, then it indicates that this MPIC is + connected as a slave to another interrupt controller. This is + typically the case on Armada 375 and Armada 38x, where the MPIC is + connected as a slave to the Cortex-A9 GIC. The provided interrupt + indicate to which GIC interrupt the MPIC output is connected. Example: diff --git a/Documentation/devicetree/bindings/interrupt-controller/opencores,or1k-pic.txt b/Documentation/devicetree/bindings/interrupt-controller/opencores,or1k-pic.txt new file mode 100644 index 000000000000..55c04faa3f3f --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/opencores,or1k-pic.txt @@ -0,0 +1,23 @@ +OpenRISC 1000 Programmable Interrupt Controller + +Required properties: + +- compatible : should be "opencores,or1k-pic-level" for variants with + level triggered interrupt lines, "opencores,or1k-pic-edge" for variants with + edge triggered interrupt lines or "opencores,or1200-pic" for machines + with the non-spec compliant or1200 type implementation. + + "opencores,or1k-pic" is also provided as an alias to "opencores,or1200-pic", + but this is only for backwards compatibility. + +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value shall be 1. + +Example: + +intc: interrupt-controller { + compatible = "opencores,or1k-pic-level"; + interrupt-controller; + #interrupt-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt index 1f8b0c507c26..c73acd060093 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt @@ -2,7 +2,13 @@ DT bindings for the R-/SH-Mobile irqpin controller Required properties: -- compatible: has to be "renesas,intc-irqpin" +- compatible: has to be "renesas,intc-irqpin-<soctype>", "renesas,intc-irqpin" + as fallback. + Examples with soctypes are: + - "renesas,intc-irqpin-r8a7740" (R-Mobile A1) + - "renesas,intc-irqpin-r8a7778" (R-Car M1A) + - "renesas,intc-irqpin-r8a7779" (R-Car H1) + - "renesas,intc-irqpin-sh73a0" (SH-Mobile AG5) - #interrupt-cells: has to be <2>: an interrupt index and flags, as defined in interrupts.txt in this directory diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt new file mode 100644 index 000000000000..1a88e62228e5 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt @@ -0,0 +1,32 @@ +DT bindings for the R-Mobile/R-Car interrupt controller + +Required properties: + +- compatible: has to be "renesas,irqc-<soctype>", "renesas,irqc" as fallback. + Examples with soctypes are: + - "renesas,irqc-r8a73a4" (R-Mobile AP6) + - "renesas,irqc-r8a7790" (R-Car H2) + - "renesas,irqc-r8a7791" (R-Car M2-W) + - "renesas,irqc-r8a7792" (R-Car V2H) + - "renesas,irqc-r8a7793" (R-Car M2-N) + - "renesas,irqc-r8a7794" (R-Car E2) +- #interrupt-cells: has to be <2>: an interrupt index and flags, as defined in + interrupts.txt in this directory + +Optional properties: + +- any properties, listed in interrupts.txt, and any standard resource allocation + properties + +Example: + + irqc0: interrupt-controller@e61c0000 { + compatible = "renesas,irqc-r8a7790", "renesas,irqc"; + #interrupt-cells = <2>; + interrupt-controller; + reg = <0 0xe61c0000 0 0x200>; + interrupts = <0 0 IRQ_TYPE_LEVEL_HIGH>, + <0 1 IRQ_TYPE_LEVEL_HIGH>, + <0 2 IRQ_TYPE_LEVEL_HIGH>, + <0 3 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,keystone-irq.txt b/Documentation/devicetree/bindings/interrupt-controller/ti,keystone-irq.txt new file mode 100644 index 000000000000..d9bb106bdd16 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/ti,keystone-irq.txt @@ -0,0 +1,36 @@ +Keystone 2 IRQ controller IP + +On Keystone SOCs, DSP cores can send interrupts to ARM +host using the IRQ controller IP. It provides 28 IRQ signals to ARM. +The IRQ handler running on HOST OS can identify DSP signal source by +analyzing SRCCx bits in IPCARx registers. This is one of the component +used by the IPC mechanism used on Keystone SOCs. + +Required Properties: +- compatible: should be "ti,keystone-irq" +- ti,syscon-dev : phandle and offset pair. The phandle to syscon used to + access device control registers and the offset inside + device control registers range. +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode interrupt + source should be 1. +- interrupts: interrupt reference to primary interrupt controller + +Please refer to interrupts.txt in this directory for details of the common +Interrupt Controllers bindings used by client devices. + +Example: + kirq0: keystone_irq0@026202a0 { + compatible = "ti,keystone-irq"; + ti,syscon-dev = <&devctrl 0x2a0>; + interrupts = <GIC_SPI 4 IRQ_TYPE_EDGE_RISING>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + dsp0: dsp0 { + compatible = "linux,rproc-user"; + ... + interrupt-parent = <&kirq0>; + interrupts = <10 2>; + }; diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu.txt b/Documentation/devicetree/bindings/iommu/arm,smmu.txt index e34c6cdd8ba8..06760503a819 100644 --- a/Documentation/devicetree/bindings/iommu/arm,smmu.txt +++ b/Documentation/devicetree/bindings/iommu/arm,smmu.txt @@ -14,6 +14,7 @@ conditions. "arm,smmu-v1" "arm,smmu-v2" "arm,mmu-400" + "arm,mmu-401" "arm,mmu-500" depending on the particular implementation and/or the @@ -42,11 +43,11 @@ conditions. ** System MMU optional properties: -- smmu-parent : When multiple SMMUs are chained together, this - property can be used to provide a phandle to the - parent SMMU (that is the next SMMU on the path going - from the mmu-masters towards memory) node for this - SMMU. +- calxeda,smmu-secure-config-access : Enable proper handling of buggy + implementations that always use secure access to + SMMU configuration registers. In this case non-secure + aliases of secure registers have to be used during + SMMU configuration. Example: diff --git a/Documentation/devicetree/bindings/iommu/iommu.txt b/Documentation/devicetree/bindings/iommu/iommu.txt new file mode 100644 index 000000000000..5a8b4624defc --- /dev/null +++ b/Documentation/devicetree/bindings/iommu/iommu.txt @@ -0,0 +1,182 @@ +This document describes the generic device tree binding for IOMMUs and their +master(s). + + +IOMMU device node: +================== + +An IOMMU can provide the following services: + +* Remap address space to allow devices to access physical memory ranges that + they otherwise wouldn't be capable of accessing. + + Example: 32-bit DMA to 64-bit physical addresses + +* Implement scatter-gather at page level granularity so that the device does + not have to. + +* Provide system protection against "rogue" DMA by forcing all accesses to go + through the IOMMU and faulting when encountering accesses to unmapped + address regions. + +* Provide address space isolation between multiple contexts. + + Example: Virtualization + +Device nodes compatible with this binding represent hardware with some of the +above capabilities. + +IOMMUs can be single-master or multiple-master. Single-master IOMMU devices +typically have a fixed association to the master device, whereas multiple- +master IOMMU devices can translate accesses from more than one master. + +The device tree node of the IOMMU device's parent bus must contain a valid +"dma-ranges" property that describes how the physical address space of the +IOMMU maps to memory. An empty "dma-ranges" property means that there is a +1:1 mapping from IOMMU to memory. + +Required properties: +-------------------- +- #iommu-cells: The number of cells in an IOMMU specifier needed to encode an + address. + +The meaning of the IOMMU specifier is defined by the device tree binding of +the specific IOMMU. Below are a few examples of typical use-cases: + +- #iommu-cells = <0>: Single master IOMMU devices are not configurable and + therefore no additional information needs to be encoded in the specifier. + This may also apply to multiple master IOMMU devices that do not allow the + association of masters to be configured. Note that an IOMMU can by design + be multi-master yet only expose a single master in a given configuration. + In such cases the number of cells will usually be 1 as in the next case. +- #iommu-cells = <1>: Multiple master IOMMU devices may need to be configured + in order to enable translation for a given master. In such cases the single + address cell corresponds to the master device's ID. In some cases more than + one cell can be required to represent a single master ID. +- #iommu-cells = <4>: Some IOMMU devices allow the DMA window for masters to + be configured. The first cell of the address in this may contain the master + device's ID for example, while the second cell could contain the start of + the DMA window for the given device. The length of the DMA window is given + by the third and fourth cells. + +Note that these are merely examples and real-world use-cases may use different +definitions to represent their individual needs. Always refer to the specific +IOMMU binding for the exact meaning of the cells that make up the specifier. + + +IOMMU master node: +================== + +Devices that access memory through an IOMMU are called masters. A device can +have multiple master interfaces (to one or more IOMMU devices). + +Required properties: +-------------------- +- iommus: A list of phandle and IOMMU specifier pairs that describe the IOMMU + master interfaces of the device. One entry in the list describes one master + interface of the device. + +When an "iommus" property is specified in a device tree node, the IOMMU will +be used for address translation. If a "dma-ranges" property exists in the +device's parent node it will be ignored. An exception to this rule is if the +referenced IOMMU is disabled, in which case the "dma-ranges" property of the +parent shall take effect. Note that merely disabling a device tree node does +not guarantee that the IOMMU is really disabled since the hardware may not +have a means to turn off translation. But it is invalid in such cases to +disable the IOMMU's device tree node in the first place because it would +prevent any driver from properly setting up the translations. + + +Notes: +====== + +One possible extension to the above is to use an "iommus" property along with +a "dma-ranges" property in a bus device node (such as PCI host bridges). This +can be useful to describe how children on the bus relate to the IOMMU if they +are not explicitly listed in the device tree (e.g. PCI devices). However, the +requirements of that use-case haven't been fully determined yet. Implementing +this is therefore not recommended without further discussion and extension of +this binding. + + +Examples: +========= + +Single-master IOMMU: +-------------------- + + iommu { + #iommu-cells = <0>; + }; + + master { + iommus = <&{/iommu}>; + }; + +Multiple-master IOMMU with fixed associations: +---------------------------------------------- + + /* multiple-master IOMMU */ + iommu { + /* + * Masters are statically associated with this IOMMU and share + * the same address translations because the IOMMU does not + * have sufficient information to distinguish between masters. + * + * Consequently address translation is always on or off for + * all masters at any given point in time. + */ + #iommu-cells = <0>; + }; + + /* static association with IOMMU */ + master@1 { + reg = <1>; + iommus = <&{/iommu}>; + }; + + /* static association with IOMMU */ + master@2 { + reg = <2>; + iommus = <&{/iommu}>; + }; + +Multiple-master IOMMU: +---------------------- + + iommu { + /* the specifier represents the ID of the master */ + #iommu-cells = <1>; + }; + + master@1 { + /* device has master ID 42 in the IOMMU */ + iommus = <&{/iommu} 42>; + }; + + master@2 { + /* device has master IDs 23 and 24 in the IOMMU */ + iommus = <&{/iommu} 23>, <&{/iommu} 24>; + }; + +Multiple-master IOMMU with configurable DMA window: +--------------------------------------------------- + + / { + iommu { + /* + * One cell for the master ID and one cell for the + * address of the DMA window. The length of the DMA + * window is encoded in two cells. + * + * The DMA window is the range addressable by the + * master (i.e. the I/O virtual address space). + */ + #iommu-cells = <4>; + }; + + master { + /* master ID 42, 4 GiB DMA window starting at 0 */ + iommus = <&{/iommu} 42 0 0x1 0x0>; + }; + }; diff --git a/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt b/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt new file mode 100644 index 000000000000..6fa4c737af23 --- /dev/null +++ b/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt @@ -0,0 +1,70 @@ +Samsung Exynos IOMMU H/W, System MMU (System Memory Management Unit) + +Samsung's Exynos architecture contains System MMUs that enables scattered +physical memory chunks visible as a contiguous region to DMA-capable peripheral +devices like MFC, FIMC, FIMD, GScaler, FIMC-IS and so forth. + +System MMU is an IOMMU and supports identical translation table format to +ARMv7 translation tables with minimum set of page properties including access +permissions, shareability and security protection. In addition, System MMU has +another capabilities like L2 TLB or block-fetch buffers to minimize translation +latency. + +System MMUs are in many to one relation with peripheral devices, i.e. single +peripheral device might have multiple System MMUs (usually one for each bus +master), but one System MMU can handle transactions from only one peripheral +device. The relation between a System MMU and the peripheral device needs to be +defined in device node of the peripheral device. + +MFC in all Exynos SoCs and FIMD, M2M Scalers and G2D in Exynos5420 has 2 System +MMUs. +* MFC has one System MMU on its left and right bus. +* FIMD in Exynos5420 has one System MMU for window 0 and 4, the other system MMU + for window 1, 2 and 3. +* M2M Scalers and G2D in Exynos5420 has one System MMU on the read channel and + the other System MMU on the write channel. +The drivers must consider how to handle those System MMUs. One of the idea is +to implement child devices or sub-devices which are the client devices of the +System MMU. + +Note: +The current DT binding for the Exynos System MMU is incomplete. +The following properties can be removed or changed, if found incompatible with +the "Generic IOMMU Binding" support for attaching devices to the IOMMU. + +Required properties: +- compatible: Should be "samsung,exynos-sysmmu" +- reg: A tuple of base address and size of System MMU registers. +- interrupt-parent: The phandle of the interrupt controller of System MMU +- interrupts: An interrupt specifier for interrupt signal of System MMU, + according to the format defined by a particular interrupt + controller. +- clock-names: Should be "sysmmu" if the System MMU is needed to gate its clock. + Optional "master" if the clock to the System MMU is gated by + another gate clock other than "sysmmu". + Exynos4 SoCs, there needs no "master" clock. + Exynos5 SoCs, some System MMUs must have "master" clocks. +- clocks: Required if the System MMU is needed to gate its clock. +- samsung,power-domain: Required if the System MMU is needed to gate its power. + Please refer to the following document: + Documentation/devicetree/bindings/arm/exynos/power_domain.txt + +Examples: + gsc_0: gsc@13e00000 { + compatible = "samsung,exynos5-gsc"; + reg = <0x13e00000 0x1000>; + interrupts = <0 85 0>; + samsung,power-domain = <&pd_gsc>; + clocks = <&clock CLK_GSCL0>; + clock-names = "gscl"; + }; + + sysmmu_gsc0: sysmmu@13E80000 { + compatible = "samsung,exynos-sysmmu"; + reg = <0x13E80000 0x1000>; + interrupt-parent = <&combiner>; + interrupts = <2 0>; + clock-names = "sysmmu", "master"; + clocks = <&clock CLK_SMMU_GSCL0>, <&clock CLK_GSCL0>; + samsung,power-domain = <&pd_gsc>; + }; diff --git a/Documentation/devicetree/bindings/iommu/ti,omap-iommu.txt b/Documentation/devicetree/bindings/iommu/ti,omap-iommu.txt new file mode 100644 index 000000000000..42531dc387aa --- /dev/null +++ b/Documentation/devicetree/bindings/iommu/ti,omap-iommu.txt @@ -0,0 +1,26 @@ +OMAP2+ IOMMU + +Required properties: +- compatible : Should be one of, + "ti,omap2-iommu" for OMAP2/OMAP3 IOMMU instances + "ti,omap4-iommu" for OMAP4/OMAP5 IOMMU instances + "ti,dra7-iommu" for DRA7xx IOMMU instances +- ti,hwmods : Name of the hwmod associated with the IOMMU instance +- reg : Address space for the configuration registers +- interrupts : Interrupt specifier for the IOMMU instance + +Optional properties: +- ti,#tlb-entries : Number of entries in the translation look-aside buffer. + Should be either 8 or 32 (default: 32) +- ti,iommu-bus-err-back : Indicates the IOMMU instance supports throwing + back a bus error response on MMU faults. + +Example: + /* OMAP3 ISP MMU */ + mmu_isp: mmu@480bd400 { + compatible = "ti,omap2-iommu"; + reg = <0x480bd400 0x80>; + interrupts = <24>; + ti,hwmods = "mmu_isp"; + ti,#tlb-entries = <8>; + }; diff --git a/Documentation/devicetree/bindings/leds/leds-gpio.txt b/Documentation/devicetree/bindings/leds/leds-gpio.txt index df1b3080f6b8..f77148f372ea 100644 --- a/Documentation/devicetree/bindings/leds/leds-gpio.txt +++ b/Documentation/devicetree/bindings/leds/leds-gpio.txt @@ -21,6 +21,8 @@ LED sub-node properties: on). The "keep" setting will keep the LED at whatever its current state is, without producing a glitch. The default is off if this property is not present. +- retain-state-suspended: (optional) The suspend state can be retained.Such + as charge-led gpio. Examples: @@ -50,3 +52,13 @@ run-control { default-state = "on"; }; }; + +leds { + compatible = "gpio-leds"; + + charger-led { + gpios = <&gpio1 2 0>; + linux,default-trigger = "max8903-charger-charging"; + retain-state-suspended; + }; +}; diff --git a/Documentation/devicetree/bindings/leds/leds-lp55xx.txt b/Documentation/devicetree/bindings/leds/leds-lp55xx.txt index c55b8c016a9e..1b66a413fb9d 100644 --- a/Documentation/devicetree/bindings/leds/leds-lp55xx.txt +++ b/Documentation/devicetree/bindings/leds/leds-lp55xx.txt @@ -1,7 +1,13 @@ Binding for TI/National Semiconductor LP55xx Led Drivers Required properties: -- compatible: "national,lp5521" or "national,lp5523" or "ti,lp5562" or "ti,lp8501" +- compatible: one of + national,lp5521 + national,lp5523 + ti,lp55231 + ti,lp5562 + ti,lp8501 + - reg: I2C slave address - clock-mode: Input clock mode, (0: automode, 1: internal, 2: external) diff --git a/Documentation/devicetree/bindings/leds/leds-pwm.txt b/Documentation/devicetree/bindings/leds/leds-pwm.txt index 7297107cf832..6c6583c35f2f 100644 --- a/Documentation/devicetree/bindings/leds/leds-pwm.txt +++ b/Documentation/devicetree/bindings/leds/leds-pwm.txt @@ -13,6 +13,8 @@ LED sub-node properties: For the pwms and pwm-names property please refer to: Documentation/devicetree/bindings/pwm/pwm.txt - max-brightness : Maximum brightness possible for the LED +- active-low : (optional) For PWMs where the LED is wired to supply + rather than ground. - label : (optional) see Documentation/devicetree/bindings/leds/common.txt - linux,default-trigger : (optional) diff --git a/Documentation/devicetree/bindings/leds/pca963x.txt b/Documentation/devicetree/bindings/leds/pca963x.txt index aece3eac1b63..dafbe9931c2b 100644 --- a/Documentation/devicetree/bindings/leds/pca963x.txt +++ b/Documentation/devicetree/bindings/leds/pca963x.txt @@ -1,18 +1,19 @@ LEDs connected to pca9632, pca9633 or pca9634 Required properties: -- compatible : should be : "nxp,pca9632", "nxp,pca9633" or "nxp,pca9634" +- compatible : should be : "nxp,pca9632", "nxp,pca9633", "nxp,pca9634" or "nxp,pca9635" Optional properties: -- nxp,totem-pole : use totem pole (push-pull) instead of default open-drain +- nxp,totem-pole : use totem pole (push-pull) instead of open-drain (pca9632 defaults + to open-drain, newer chips to totem pole) - nxp,hw-blink : use hardware blinking instead of software blinking Each led is represented as a sub-node of the nxp,pca963x device. LED sub-node properties: - label : (optional) see Documentation/devicetree/bindings/leds/common.txt -- reg : number of LED line (could be from 0 to 3 in pca9632 or pca9633 - or 0 to 7 in pca9634) +- reg : number of LED line (could be from 0 to 3 in pca9632 or pca9633, + 0 to 7 in pca9634, or 0 to 15 in pca9635) - linux,default-trigger : (optional) see Documentation/devicetree/bindings/leds/common.txt diff --git a/Documentation/devicetree/bindings/leds/register-bit-led.txt b/Documentation/devicetree/bindings/leds/register-bit-led.txt new file mode 100644 index 000000000000..379cefdc0bda --- /dev/null +++ b/Documentation/devicetree/bindings/leds/register-bit-led.txt @@ -0,0 +1,99 @@ +Device Tree Bindings for Register Bit LEDs + +Register bit leds are used with syscon multifunctional devices +where single bits in a certain register can turn on/off a +single LED. The register bit LEDs appear as children to the +syscon device, with the proper compatible string. For the +syscon bindings see: +Documentation/devicetree/bindings/mfd/syscon.txt + +Each LED is represented as a sub-node of the syscon device. Each +node's name represents the name of the corresponding LED. + +LED sub-node properties: + +Required properties: +- compatible : must be "register-bit-led" +- offset : register offset to the register controlling this LED +- mask : bit mask for the bit controlling this LED in the register + typically 0x01, 0x02, 0x04 ... + +Optional properties: +- label : (optional) + see Documentation/devicetree/bindings/leds/common.txt +- linux,default-trigger : (optional) + see Documentation/devicetree/bindings/leds/common.txt +- default-state: (optional) The initial state of the LED. Valid + values are "on", "off", and "keep". If the LED is already on or off + and the default-state property is set the to same value, then no + glitch should be produced where the LED momentarily turns off (or + on). The "keep" setting will keep the LED at whatever its current + state is, without producing a glitch. The default is off if this + property is not present. + +Example: + +syscon: syscon@10000000 { + compatible = "arm,realview-pb1176-syscon", "syscon"; + reg = <0x10000000 0x1000>; + + led@08.0 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x01>; + label = "versatile:0"; + linux,default-trigger = "heartbeat"; + default-state = "on"; + }; + led@08.1 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x02>; + label = "versatile:1"; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + led@08.2 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x04>; + label = "versatile:2"; + linux,default-trigger = "cpu0"; + default-state = "off"; + }; + led@08.3 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x08>; + label = "versatile:3"; + default-state = "off"; + }; + led@08.4 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x10>; + label = "versatile:4"; + default-state = "off"; + }; + led@08.5 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x20>; + label = "versatile:5"; + default-state = "off"; + }; + led@08.6 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x40>; + label = "versatile:6"; + default-state = "off"; + }; + led@08.7 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x80>; + label = "versatile:7"; + default-state = "off"; + }; +}; diff --git a/Documentation/devicetree/bindings/leds/tca6507.txt b/Documentation/devicetree/bindings/leds/tca6507.txt index d7221b84987c..bad9102796f3 100644 --- a/Documentation/devicetree/bindings/leds/tca6507.txt +++ b/Documentation/devicetree/bindings/leds/tca6507.txt @@ -8,7 +8,7 @@ Required properties: Optional properties: - gpio-controller: allows lines to be used as output-only GPIOs. -- #gpio-cells: if present, must be 0. +- #gpio-cells: if present, must not be 0. Each led is represented as a sub-node of the ti,tca6507 device. diff --git a/Documentation/devicetree/bindings/mailbox/mailbox.txt b/Documentation/devicetree/bindings/mailbox/mailbox.txt new file mode 100644 index 000000000000..1a2cd3d266db --- /dev/null +++ b/Documentation/devicetree/bindings/mailbox/mailbox.txt @@ -0,0 +1,38 @@ +* Generic Mailbox Controller and client driver bindings + +Generic binding to provide a way for Mailbox controller drivers to +assign appropriate mailbox channel to client drivers. + +* Mailbox Controller + +Required property: +- #mbox-cells: Must be at least 1. Number of cells in a mailbox + specifier. + +Example: + mailbox: mailbox { + ... + #mbox-cells = <1>; + }; + + +* Mailbox Client + +Required property: +- mboxes: List of phandle and mailbox channel specifiers. + +Optional property: +- mbox-names: List of identifier strings for each mailbox channel + required by the client. The use of this property + is discouraged in favor of using index in list of + 'mboxes' while requesting a mailbox. Instead the + platforms may define channel indices, in DT headers, + to something legible. + +Example: + pwr_cntrl: power { + ... + mbox-names = "pwr-ctrl", "rpc"; + mboxes = <&mailbox 0 + &mailbox 1>; + }; diff --git a/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt new file mode 100644 index 000000000000..48edc4b92afb --- /dev/null +++ b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt @@ -0,0 +1,108 @@ +OMAP2+ Mailbox Driver +===================== + +The OMAP mailbox hardware facilitates communication between different processors +using a queued mailbox interrupt mechanism. The IP block is external to the +various processor subsystems and is connected on an interconnect bus. The +communication is achieved through a set of registers for message storage and +interrupt configuration registers. + +Each mailbox IP block has a certain number of h/w fifo queues and output +interrupt lines. An output interrupt line is routed to an interrupt controller +within a processor subsystem, and there can be more than one line going to a +specific processor's interrupt controller. The interrupt line connections are +fixed for an instance and are dictated by the IP integration into the SoC +(excluding the SoCs that have a Interrupt Crossbar IP). Each interrupt line is +programmable through a set of interrupt configuration registers, and have a rx +and tx interrupt source per h/w fifo. Communication between different processors +is achieved through the appropriate programming of the rx and tx interrupt +sources on the appropriate interrupt lines. + +The number of h/w fifo queues and interrupt lines dictate the usable registers. +All the current OMAP SoCs except for the newest DRA7xx SoC has a single IP +instance. DRA7xx has multiple instances with different number of h/w fifo queues +and interrupt lines between different instances. The interrupt lines can also be +routed to different processor sub-systems on DRA7xx as they are routed through +the Crossbar, a kind of interrupt router/multiplexer. + +Mailbox Device Node: +==================== +A Mailbox device node is used to represent a Mailbox IP instance within a SoC. +The sub-mailboxes are represented as child nodes of this parent node. + +Required properties: +-------------------- +- compatible: Should be one of the following, + "ti,omap2-mailbox" for OMAP2420, OMAP2430 SoCs + "ti,omap3-mailbox" for OMAP3430, OMAP3630 SoCs + "ti,omap4-mailbox" for OMAP44xx, OMAP54xx, AM33xx, + AM43xx and DRA7xx SoCs +- reg: Contains the mailbox register address range (base + address and length) +- interrupts: Contains the interrupt information for the mailbox + device. The format is dependent on which interrupt + controller the OMAP device uses +- ti,hwmods: Name of the hwmod associated with the mailbox +- ti,mbox-num-users: Number of targets (processor devices) that the mailbox + device can interrupt +- ti,mbox-num-fifos: Number of h/w fifo queues within the mailbox IP block + +Child Nodes: +============ +A child node is used for representing the actual sub-mailbox device that is +used for the communication between the host processor and a remote processor. +Each child node should have a unique node name across all the different +mailbox device nodes. + +Required properties: +-------------------- +- ti,mbox-tx: sub-mailbox descriptor property defining a Tx fifo +- ti,mbox-rx: sub-mailbox descriptor property defining a Rx fifo + +Sub-mailbox Descriptor Data +--------------------------- +Each of the above ti,mbox-tx and ti,mbox-rx properties should have 3 cells of +data that represent the following: + Cell #1 (fifo_id) - mailbox fifo id used either for transmitting + (ti,mbox-tx) or for receiving (ti,mbox-rx) + Cell #2 (irq_id) - irq identifier index number to use from the parent's + interrupts data. Should be 0 for most of the cases, a + positive index value is seen only on mailboxes that have + multiple interrupt lines connected to the MPU processor. + Cell #3 (usr_id) - mailbox user id for identifying the interrupt line + associated with generating a tx/rx fifo interrupt. + +Example: +-------- + +/* OMAP4 */ +mailbox: mailbox@4a0f4000 { + compatible = "ti,omap4-mailbox"; + reg = <0x4a0f4000 0x200>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mailbox"; + ti,mbox-num-users = <3>; + ti,mbox-num-fifos = <8>; + mbox_ipu: mbox_ipu { + ti,mbox-tx = <0 0 0>; + ti,mbox-rx = <1 0 0>; + }; + mbox_dsp: mbox_dsp { + ti,mbox-tx = <3 0 0>; + ti,mbox-rx = <2 0 0>; + }; +}; + +/* AM33xx */ +mailbox: mailbox@480C8000 { + compatible = "ti,omap4-mailbox"; + reg = <0x480C8000 0x200>; + interrupts = <77>; + ti,hwmods = "mailbox"; + ti,mbox-num-users = <4>; + ti,mbox-num-fifos = <8>; + mbox_wkupm3: wkup_m3 { + ti,mbox-tx = <0 0 0>; + ti,mbox-rx = <0 0 3>; + }; +}; diff --git a/Documentation/devicetree/bindings/media/atmel-isi.txt b/Documentation/devicetree/bindings/media/atmel-isi.txt new file mode 100644 index 000000000000..17e71b7b44c6 --- /dev/null +++ b/Documentation/devicetree/bindings/media/atmel-isi.txt @@ -0,0 +1,51 @@ +Atmel Image Sensor Interface (ISI) SoC Camera Subsystem +---------------------------------------------- + +Required properties: +- compatible: must be "atmel,at91sam9g45-isi" +- reg: physical base address and length of the registers set for the device; +- interrupts: should contain IRQ line for the ISI; +- clocks: list of clock specifiers, corresponding to entries in + the clock-names property; +- clock-names: must contain "isi_clk", which is the isi peripherial clock. + +ISI supports a single port node with parallel bus. It should contain one +'port' child node with child 'endpoint' node. Please refer to the bindings +defined in Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + isi: isi@f0034000 { + compatible = "atmel,at91sam9g45-isi"; + reg = <0xf0034000 0x4000>; + interrupts = <37 IRQ_TYPE_LEVEL_HIGH 5>; + + clocks = <&isi_clk>; + clock-names = "isi_clk"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_isi>; + + port { + #address-cells = <1>; + #size-cells = <0>; + + isi_0: endpoint { + remote-endpoint = <&ov2640_0>; + bus-width = <8>; + }; + }; + }; + + i2c1: i2c@f0018000 { + ov2640: camera@0x30 { + compatible = "omnivision,ov2640"; + reg = <0x30>; + + port { + ov2640_0: endpoint { + remote-endpoint = <&isi_0>; + bus-width = <8>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt b/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt index 937b755baf8f..bf52ed4a5067 100644 --- a/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt +++ b/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt @@ -3,9 +3,13 @@ Samsung S5P/EXYNOS SoC series JPEG codec Required properties: - compatible : should be one of: - "samsung,s5pv210-jpeg", "samsung,exynos4210-jpeg"; + "samsung,s5pv210-jpeg", "samsung,exynos4210-jpeg", + "samsung,exynos3250-jpeg"; - reg : address and length of the JPEG codec IP register set; - interrupts : specifies the JPEG codec IP interrupt; -- clocks : should contain the JPEG codec IP gate clock specifier, from the - common clock bindings; -- clock-names : should contain "jpeg" entry. +- clock-names : should contain: + - "jpeg" for the core gate clock, + - "sclk" for the special clock (optional). +- clocks : should contain the clock specifier and clock ID list + matching entries in the clock-names property; from + the common clock bindings. diff --git a/Documentation/devicetree/bindings/media/hix5hd2-ir.txt b/Documentation/devicetree/bindings/media/hix5hd2-ir.txt new file mode 100644 index 000000000000..fb5e7606643a --- /dev/null +++ b/Documentation/devicetree/bindings/media/hix5hd2-ir.txt @@ -0,0 +1,25 @@ +Device-Tree bindings for hix5hd2 ir IP + +Required properties: + - compatible: Should contain "hisilicon,hix5hd2-ir". + - reg: Base physical address of the controller and length of memory + mapped region. + - interrupts: interrupt-specifier for the sole interrupt generated by + the device. The interrupt specifier format depends on the interrupt + controller parent. + - clocks: clock phandle and specifier pair. + - hisilicon,power-syscon: phandle of syscon used to control power. + +Optional properties: + - linux,rc-map-name : Remote control map name. + +Example node: + + ir: ir@f8001000 { + compatible = "hisilicon,hix5hd2-ir"; + reg = <0xf8001000 0x1000>; + interrupts = <0 47 4>; + clocks = <&clock HIX5HD2_FIXED_24M>; + hisilicon,power-syscon = <&sysctrl>; + linux,rc-map-name = "rc-tivo"; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/Documentation/devicetree/bindings/media/i2c/adv7604.txt new file mode 100644 index 000000000000..c27cede3bd68 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt @@ -0,0 +1,70 @@ +* Analog Devices ADV7604/11 video decoder with HDMI receiver + +The ADV7604 and ADV7611 are multiformat video decoders with an integrated HDMI +receiver. The ADV7604 has four multiplexed HDMI inputs and one analog input, +and the ADV7611 has one HDMI input and no analog input. + +These device tree bindings support the ADV7611 only at the moment. + +Required Properties: + + - compatible: Must contain one of the following + - "adi,adv7611" for the ADV7611 + + - reg: I2C slave address + + - hpd-gpios: References to the GPIOs that control the HDMI hot-plug + detection pins, one per HDMI input. The active flag indicates the GPIO + level that enables hot-plug detection. + +The device node must contain one 'port' child node per device input and output +port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes +are numbered as follows. + + Port ADV7611 +------------------------------------------------------------ + HDMI 0 + Digital output 1 + +The digital output port node must contain at least one endpoint. + +Optional Properties: + + - reset-gpios: Reference to the GPIO connected to the device's reset pin. + +Optional Endpoint Properties: + + The following three properties are defined in video-interfaces.txt and are + valid for source endpoints only. + + - hsync-active: Horizontal synchronization polarity. Defaults to active low. + - vsync-active: Vertical synchronization polarity. Defaults to active low. + - pclk-sample: Pixel clock polarity. Defaults to output on the falling edge. + + If none of hsync-active, vsync-active and pclk-sample is specified the + endpoint will use embedded BT.656 synchronization. + + +Example: + + hdmi_receiver@4c { + compatible = "adi,adv7611"; + reg = <0x4c>; + + reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>; + hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>; + + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + }; + port@1 { + reg = <1>; + hdmi_in: endpoint { + remote-endpoint = <&ccdc_in>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/mt9m111.txt b/Documentation/devicetree/bindings/media/i2c/mt9m111.txt new file mode 100644 index 000000000000..ed5a334b1e57 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/mt9m111.txt @@ -0,0 +1,28 @@ +Micron 1.3Mp CMOS Digital Image Sensor + +The Micron MT9M111 is a CMOS active pixel digital image sensor with an active +array size of 1280H x 1024V. It is programmable through a simple two-wire serial +interface. + +Required Properties: +- compatible: value should be "micron,mt9m111" + +For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + i2c_master { + mt9m111@5d { + compatible = "micron,mt9m111"; + reg = <0x5d>; + + remote = <&pxa_camera>; + port { + mt9m111_1: endpoint { + bus-width = <8>; + remote-endpoint = <&pxa_camera>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/img-ir-rev1.txt b/Documentation/devicetree/bindings/media/img-ir-rev1.txt new file mode 100644 index 000000000000..5434ce61b925 --- /dev/null +++ b/Documentation/devicetree/bindings/media/img-ir-rev1.txt @@ -0,0 +1,34 @@ +* ImgTec Infrared (IR) decoder version 1 + +This binding is for Imagination Technologies' Infrared decoder block, +specifically major revision 1. + +Required properties: +- compatible: Should be "img,ir-rev1" +- reg: Physical base address of the controller and length of + memory mapped region. +- interrupts: The interrupt specifier to the cpu. + +Optional properties: +- clocks: List of clock specifiers as described in standard + clock bindings. + Up to 3 clocks may be specified in the following order: + 1st: Core clock (defaults to 32.768KHz if omitted). + 2nd: System side (fast) clock. + 3rd: Power modulation clock. +- clock-names: List of clock names corresponding to the clocks + specified in the clocks property. + Accepted clock names are: + "core": Core clock. + "sys": System clock. + "mod": Power modulation clock. + +Example: + + ir@02006200 { + compatible = "img,ir-rev1"; + reg = <0x02006200 0x100>; + interrupts = <29 4>; + clocks = <&clk_32khz>; + clock-names = "core"; + }; diff --git a/Documentation/devicetree/bindings/media/pxa-camera.txt b/Documentation/devicetree/bindings/media/pxa-camera.txt new file mode 100644 index 000000000000..11f5b5d51af8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/pxa-camera.txt @@ -0,0 +1,43 @@ +Marvell PXA camera host interface + +Required properties: + - compatible: Should be "marvell,pxa270-qci" + - reg: register base and size + - interrupts: the interrupt number + - any required generic properties defined in video-interfaces.txt + +Optional properties: + - clocks: input clock (see clock-bindings.txt) + - clock-output-names: should contain the name of the clock driving the + sensor master clock MCLK + - clock-frequency: host interface is driving MCLK, and MCLK rate is this rate + +Example: + + pxa_camera: pxa_camera@50000000 { + compatible = "marvell,pxa270-qci"; + reg = <0x50000000 0x1000>; + interrupts = <33>; + + clocks = <&pxa2xx_clks 24>; + clock-names = "ciclk"; + clock-frequency = <50000000>; + clock-output-names = "qci_mclk"; + + status = "okay"; + + port { + #address-cells = <1>; + #size-cells = <0>; + + /* Parallel bus endpoint */ + qci: endpoint@0 { + reg = <0>; /* Local endpoint # */ + remote-endpoint = <&mt9m111_1>; + bus-width = <8>; /* Used data lines */ + hsync-active = <0>; /* Active low */ + vsync-active = <0>; /* Active low */ + pclk-sample = <1>; /* Rising */ + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt new file mode 100644 index 000000000000..ba61782c2af9 --- /dev/null +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt @@ -0,0 +1,86 @@ +Renesas RCar Video Input driver (rcar_vin) +------------------------------------------ + +The rcar_vin device provides video input capabilities for the Renesas R-Car +family of devices. The current blocks are always slaves and suppot one input +channel which can be either RGB, YUYV or BT656. + + - compatible: Must be one of the following + - "renesas,vin-r8a7791" for the R8A7791 device + - "renesas,vin-r8a7790" for the R8A7790 device + - "renesas,vin-r8a7779" for the R8A7779 device + - "renesas,vin-r8a7778" for the R8A7778 device + - reg: the register base and size for the device registers + - interrupts: the interrupt for the device + - clocks: Reference to the parent clock + +Additionally, an alias named vinX will need to be created to specify +which video input device this is. + +The per-board settings: + - port sub-node describing a single endpoint connected to the vin + as described in video-interfaces.txt[1]. Only the first one will + be considered as each vin interface has one input port. + + These settings are used to work out video input format and widths + into the system. + + +Device node example +------------------- + + aliases { + vin0 = &vin0; + }; + + vin0: vin@0xe6ef0000 { + compatible = "renesas,vin-r8a7790"; + clocks = <&mstp8_clks R8A7790_CLK_VIN0>; + reg = <0 0xe6ef0000 0 0x1000>; + interrupts = <0 188 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + +Board setup example (vin1 composite video input) +------------------------------------------------ + +&i2c2 { + status = "ok"; + pinctrl-0 = <&i2c2_pins>; + pinctrl-names = "default"; + + adv7180@20 { + compatible = "adi,adv7180"; + reg = <0x20>; + remote = <&vin1>; + + port { + adv7180: endpoint { + bus-width = <8>; + remote-endpoint = <&vin1ep0>; + }; + }; + }; +}; + +/* composite video input */ +&vin1 { + pinctrl-0 = <&vin1_pins>; + pinctrl-names = "default"; + + status = "ok"; + + port { + #address-cells = <1>; + #size-cells = <0>; + + vin1ep0: endpoint { + remote-endpoint = <&adv7180>; + bus-width = <8>; + }; + }; +}; + + + +[1] video-interfaces.txt common video media interface diff --git a/Documentation/devicetree/bindings/media/renesas,vsp1.txt b/Documentation/devicetree/bindings/media/renesas,vsp1.txt new file mode 100644 index 000000000000..87fe08abf36d --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,vsp1.txt @@ -0,0 +1,43 @@ +* Renesas VSP1 Video Processing Engine + +The VSP1 is a video processing engine that supports up-/down-scaling, alpha +blending, color space conversion and various other image processing features. +It can be found in the Renesas R-Car second generation SoCs. + +Required properties: + + - compatible: Must contain "renesas,vsp1" + + - reg: Base address and length of the registers block for the VSP1. + - interrupts: VSP1 interrupt specifier. + - clocks: A phandle + clock-specifier pair for the VSP1 functional clock. + + - renesas,#rpf: Number of Read Pixel Formatter (RPF) modules in the VSP1. + - renesas,#uds: Number of Up Down Scaler (UDS) modules in the VSP1. + - renesas,#wpf: Number of Write Pixel Formatter (WPF) modules in the VSP1. + + +Optional properties: + + - renesas,has-lif: Boolean, indicates that the LCD Interface (LIF) module is + available. + - renesas,has-lut: Boolean, indicates that the Look Up Table (LUT) module is + available. + - renesas,has-sru: Boolean, indicates that the Super Resolution Unit (SRU) + module is available. + + +Example: R8A7790 (R-Car H2) VSP1-S node + + vsp1@fe928000 { + compatible = "renesas,vsp1"; + reg = <0 0xfe928000 0 0x8000>; + interrupts = <0 267 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp1_clks R8A7790_CLK_VSP1_S>; + + renesas,has-lut; + renesas,has-sru; + renesas,#rpf = <5>; + renesas,#uds = <3>; + renesas,#wpf = <4>; + }; diff --git a/Documentation/devicetree/bindings/media/s5p-mfc.txt b/Documentation/devicetree/bindings/media/s5p-mfc.txt index f4181680831b..3e3c5f349570 100644 --- a/Documentation/devicetree/bindings/media/s5p-mfc.txt +++ b/Documentation/devicetree/bindings/media/s5p-mfc.txt @@ -10,7 +10,8 @@ Required properties: - compatible : value should be either one among the following (a) "samsung,mfc-v5" for MFC v5 present in Exynos4 SoCs (b) "samsung,mfc-v6" for MFC v6 present in Exynos5 SoCs - (b) "samsung,mfc-v7" for MFC v7 present in Exynos5420 SoC + (c) "samsung,mfc-v7" for MFC v7 present in Exynos5420 SoC + (d) "samsung,mfc-v8" for MFC v8 present in Exynos5800 SoC - reg : Physical base address of the IP registers and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/media/samsung-fimc.txt b/Documentation/devicetree/bindings/media/samsung-fimc.txt index 96312f6c4c26..922d6f8e74be 100644 --- a/Documentation/devicetree/bindings/media/samsung-fimc.txt +++ b/Documentation/devicetree/bindings/media/samsung-fimc.txt @@ -15,11 +15,21 @@ Common 'camera' node Required properties: -- compatible : must be "samsung,fimc", "simple-bus" -- clocks : list of clock specifiers, corresponding to entries in - the clock-names property; -- clock-names : must contain "sclk_cam0", "sclk_cam1", "pxl_async0", - "pxl_async1" entries, matching entries in the clocks property. +- compatible: must be "samsung,fimc", "simple-bus" +- clocks: list of clock specifiers, corresponding to entries in + the clock-names property; +- clock-names : must contain "sclk_cam0", "sclk_cam1", "pxl_async0", + "pxl_async1" entries, matching entries in the clocks property. + +- #clock-cells: from the common clock bindings (../clock/clock-bindings.txt), + must be 1. A clock provider is associated with the 'camera' node and it should + be referenced by external sensors that use clocks provided by the SoC on + CAM_*_CLKOUT pins. The clock specifier cell stores an index of a clock. + The indices are 0, 1 for CAM_A_CLKOUT, CAM_B_CLKOUT clocks respectively. + +- clock-output-names: from the common clock bindings, should contain names of + clocks registered by the camera subsystem corresponding to CAM_A_CLKOUT, + CAM_B_CLKOUT output clocks respectively. The pinctrl bindings defined in ../pinctrl/pinctrl-bindings.txt must be used to define a required pinctrl state named "default" and optional pinctrl states: @@ -32,6 +42,7 @@ way around. The 'camera' node must include at least one 'fimc' child node. + 'fimc' device nodes ------------------- @@ -88,8 +99,8 @@ port nodes specifies data input - 0, 1 indicates input A, B respectively. Optional properties -- samsung,camclk-out : specifies clock output for remote sensor, - 0 - CAM_A_CLKOUT, 1 - CAM_B_CLKOUT; +- samsung,camclk-out (deprecated) : specifies clock output for remote sensor, + 0 - CAM_A_CLKOUT, 1 - CAM_B_CLKOUT; Image sensor nodes ------------------ @@ -97,8 +108,6 @@ Image sensor nodes The sensor device nodes should be added to their control bus controller (e.g. I2C0) nodes and linked to a port node in the csis or the parallel-ports node, using the common video interfaces bindings, defined in video-interfaces.txt. -The implementation of this bindings requires clock-frequency property to be -present in the sensor device nodes. Example: @@ -114,7 +123,7 @@ Example: vddio-supply = <...>; clock-frequency = <24000000>; - clocks = <...>; + clocks = <&camera 1>; clock-names = "mclk"; port { @@ -135,7 +144,7 @@ Example: vddio-supply = <...>; clock-frequency = <24000000>; - clocks = <...>; + clocks = <&camera 0>; clock-names = "mclk"; port { @@ -149,12 +158,17 @@ Example: camera { compatible = "samsung,fimc", "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - status = "okay"; - + clocks = <&clock 132>, <&clock 133>, <&clock 351>, + <&clock 352>; + clock-names = "sclk_cam0", "sclk_cam1", "pxl_async0", + "pxl_async1"; + #clock-cells = <1>; + clock-output-names = "cam_a_clkout", "cam_b_clkout"; pinctrl-names = "default"; pinctrl-0 = <&cam_port_a_clk_active>; + status = "okay"; + #address-cells = <1>; + #size-cells = <1>; /* parallel camera ports */ parallel-ports { diff --git a/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt b/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt new file mode 100644 index 000000000000..2c85c4538a6d --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt @@ -0,0 +1,97 @@ +Samsung S5C73M3 8Mp camera ISP +------------------------------ + +The S5C73M3 camera ISP supports MIPI CSI-2 and parallel (ITU-R BT.656) video +data busses. The I2C bus is the main control bus and additionally the SPI bus +is used, mostly for transferring the firmware to and from the device. Two +slave device nodes corresponding to these control bus interfaces are required +and should be placed under respective bus controller nodes. + +I2C slave device node +--------------------- + +Required properties: + +- compatible : "samsung,s5c73m3"; +- reg : I2C slave address of the sensor; +- vdd-int-supply : digital power supply (1.2V); +- vdda-supply : analog power supply (1.2V); +- vdd-reg-supply : regulator input power supply (2.8V); +- vddio-host-supply : host I/O power supply (1.8V to 2.8V); +- vddio-cis-supply : CIS I/O power supply (1.2V to 1.8V); +- vdd-af-supply : lens power supply (2.8V); +- xshutdown-gpios : specifier of GPIO connected to the XSHUTDOWN pin; +- standby-gpios : specifier of GPIO connected to the STANDBY pin; +- clocks : should contain list of phandle and clock specifier pairs + according to common clock bindings for the clocks described + in the clock-names property; +- clock-names : should contain "cis_extclk" entry for the CIS_EXTCLK clock; + +Optional properties: + +- clock-frequency : the frequency at which the "cis_extclk" clock should be + configured to operate, in Hz; if this property is not + specified default 24 MHz value will be used. + +The common video interfaces bindings (see video-interfaces.txt) should be used +to specify link from the S5C73M3 to an external image data receiver. The S5C73M3 +device node should contain one 'port' child node with an 'endpoint' subnode for +this purpose. The data link from a raw image sensor to the S5C73M3 can be +similarly specified, but it is optional since the S5C73M3 ISP and a raw image +sensor are usually inseparable and form a hybrid module. + +Following properties are valid for the endpoint node(s): + +endpoint subnode +---------------- + +- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in + video-interfaces.txt. This sensor doesn't support data lane remapping + and physical lane indexes in subsequent elements of the array should + be only consecutive ascending values. + +SPI device node +--------------- + +Required properties: + +- compatible : "samsung,s5c73m3"; + +For more details see description of the SPI busses bindings +(../spi/spi-bus.txt) and bindings of a specific bus controller. + +Example: + +i2c@138A000000 { + ... + s5c73m3@3c { + compatible = "samsung,s5c73m3"; + reg = <0x3c>; + vdd-int-supply = <&buck9_reg>; + vdda-supply = <&ldo17_reg>; + vdd-reg-supply = <&cam_io_reg>; + vddio-host-supply = <&ldo18_reg>; + vddio-cis-supply = <&ldo9_reg>; + vdd-af-supply = <&cam_af_reg>; + clock-frequency = <24000000>; + clocks = <&clk 0>; + clock-names = "cis_extclk"; + reset-gpios = <&gpf1 3 1>; + standby-gpios = <&gpm0 1 1>; + port { + s5c73m3_ep: endpoint { + remote-endpoint = <&csis0_ep>; + data-lanes = <1 2 3 4>; + }; + }; + }; +}; + +spi@1392000 { + ... + s5c73m3_spi: s5c73m3@0 { + compatible = "samsung,s5c73m3"; + reg = <0>; + ... + }; +}; diff --git a/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt new file mode 100644 index 000000000000..cce01e82f3e3 --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt @@ -0,0 +1,33 @@ +Samsung S5K6A3(YX) raw image sensor +--------------------------------- + +S5K6A3(YX) is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces +and CCI (I2C compatible) control bus. + +Required properties: + +- compatible : "samsung,s5k6a3"; +- reg : I2C slave address of the sensor; +- svdda-supply : core voltage supply; +- svddio-supply : I/O voltage supply; +- afvdd-supply : AF (actuator) voltage supply; +- gpios : specifier of a GPIO connected to the RESET pin; +- clocks : should contain list of phandle and clock specifier pairs + according to common clock bindings for the clocks described + in the clock-names property; +- clock-names : should contain "extclk" entry for the sensor's EXTCLK clock; + +Optional properties: + +- clock-frequency : the frequency at which the "extclk" clock should be + configured to operate, in Hz; if this property is not + specified default 24 MHz value will be used. + +The common video interfaces bindings (see video-interfaces.txt) should be +used to specify link to the image data receiver. The S5K6A3(YX) device +node should contain one 'port' child node with an 'endpoint' subnode. + +Following properties are valid for the endpoint node: + +- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in + video-interfaces.txt. The sensor supports only one data lane. diff --git a/Documentation/devicetree/bindings/media/sunxi-ir.txt b/Documentation/devicetree/bindings/media/sunxi-ir.txt new file mode 100644 index 000000000000..23dd5ad07b7c --- /dev/null +++ b/Documentation/devicetree/bindings/media/sunxi-ir.txt @@ -0,0 +1,23 @@ +Device-Tree bindings for SUNXI IR controller found in sunXi SoC family + +Required properties: +- compatible : should be "allwinner,sun4i-a10-ir"; +- clocks : list of clock specifiers, corresponding to + entries in clock-names property; +- clock-names : should contain "apb" and "ir" entries; +- interrupts : should contain IR IRQ number; +- reg : should contain IO map address for IR. + +Optional properties: +- linux,rc-map-name : Remote control map name. + +Example: + +ir0: ir@01c21800 { + compatible = "allwinner,sun4i-a10-ir"; + clocks = <&apb0_gates 6>, <&ir0_clk>; + clock-names = "apb", "ir"; + interrupts = <0 5 1>; + reg = <0x01C21800 0x40>; + linux,rc-map-name = "rc-rc6-mce"; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/ifc.txt b/Documentation/devicetree/bindings/memory-controllers/fsl/ifc.txt index d5e370450ac0..d5e370450ac0 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/ifc.txt +++ b/Documentation/devicetree/bindings/memory-controllers/fsl/ifc.txt diff --git a/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt b/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt index 653c90c34a71..1ee3bc09f319 100644 --- a/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt +++ b/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt @@ -6,10 +6,11 @@ The actual devices are instantiated from the child nodes of a Device Bus node. Required properties: - - compatible: Currently only Armada 370/XP SoC are supported, - with this compatible string: + - compatible: Armada 370/XP SoC are supported using the + "marvell,mvebu-devbus" compatible string. - marvell,mvebu-devbus + Orion5x SoC are supported using the + "marvell,orion-devbus" compatible string. - reg: A resource specifier for the register space. This is the base address of a chip select within @@ -22,7 +23,14 @@ Required properties: integer values for each chip-select line in use: 0 <physical address of mapping> <size> -Mandatory timing properties for child nodes: +Optional properties: + + - devbus,keep-config This property can optionally be used to keep + using the timing parameters set by the + bootloader. It makes all the timing properties + described below unused. + +Timing properties for child nodes: Read parameters: @@ -30,21 +38,26 @@ Read parameters: drive the AD bus after the completion of a device read. This prevents contentions on the Device Bus after a read cycle from a slow device. + Mandatory, except if devbus,keep-config is used. - - devbus,bus-width: Defines the bus width (e.g. <16>) + - devbus,bus-width: Defines the bus width, in bits (e.g. <16>). + Mandatory, except if devbus,keep-config is used. - devbus,badr-skew-ps: Defines the time delay from from A[2:0] toggle, to read data sample. This parameter is useful for synchronous pipelined devices, where the address precedes the read data by one or two cycles. + Mandatory, except if devbus,keep-config is used. - devbus,acc-first-ps: Defines the time delay from the negation of ALE[0] to the cycle that the first read data is sampled by the controller. + Mandatory, except if devbus,keep-config is used. - devbus,acc-next-ps: Defines the time delay between the cycle that samples data N and the cycle that samples data N+1 (in burst accesses). + Mandatory, except if devbus,keep-config is used. - devbus,rd-setup-ps: Defines the time delay between DEV_CSn assertion to DEV_OEn assertion. If set to 0 (default), @@ -52,6 +65,8 @@ Read parameters: This parameter has no affect on <acc-first-ps> parameter (no affect on first data sample). Set <rd-setup-ps> to a value smaller than <acc-first-ps>. + Mandatory for "marvell,mvebu-devbus" compatible string, + except if devbus,keep-config is used. - devbus,rd-hold-ps: Defines the time between the last data sample to the de-assertion of DEV_CSn. If set to 0 (default), @@ -62,16 +77,20 @@ Read parameters: last data sampled. Also this parameter has no affect on <turn-off-ps> parameter. Set <rd-hold-ps> to a value smaller than <turn-off-ps>. + Mandatory for "marvell,mvebu-devbus" compatible string, + except if devbus,keep-config is used. Write parameters: - devbus,ale-wr-ps: Defines the time delay from the ALE[0] negation cycle to the DEV_WEn assertion. + Mandatory. - devbus,wr-low-ps: Defines the time during which DEV_WEn is active. A[2:0] and Data are kept valid as long as DEV_WEn is active. This parameter defines the setup time of address and data to DEV_WEn rise. + Mandatory. - devbus,wr-high-ps: Defines the time during which DEV_WEn is kept inactive (high) between data beats of a burst write. @@ -79,10 +98,13 @@ Write parameters: <wr-high-ps> - <tick> ps. This parameter defines the hold time of address and data after DEV_WEn rise. + Mandatory. - devbus,sync-enable: Synchronous device enable. 1: True 0: False + Mandatory for "marvell,mvebu-devbus" compatible string, + except if devbus,keep-config is used. An example for an Armada XP GP board, with a 16 MiB NOR device as child is showed below. Note that the Device Bus driver is in charge of allocating diff --git a/Documentation/devicetree/bindings/memory-controllers/mvebu-sdram-controller.txt b/Documentation/devicetree/bindings/memory-controllers/mvebu-sdram-controller.txt new file mode 100644 index 000000000000..89657d1d4cd4 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/mvebu-sdram-controller.txt @@ -0,0 +1,21 @@ +Device Tree bindings for MVEBU SDRAM controllers + +The Marvell EBU SoCs all have a SDRAM controller. The SDRAM controller +differs from one SoC variant to another, but they also share a number +of commonalities. + +For now, this Device Tree binding documentation only documents the +Armada XP SDRAM controller. + +Required properties: + + - compatible: for Armada XP, "marvell,armada-xp-sdram-controller" + - reg: a resource specifier for the register space, which should + include all SDRAM controller registers as per the datasheet. + +Example: + +sdramc@1400 { + compatible = "marvell,armada-xp-sdram-controller"; + reg = <0x1400 0x500>; +}; diff --git a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt new file mode 100644 index 000000000000..f3db93c85eea --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt @@ -0,0 +1,36 @@ +NVIDIA Tegra Memory Controller device tree bindings +=================================================== + +Required properties: +- compatible: Should be "nvidia,tegra<chip>-mc" +- reg: Physical base address and length of the controller's registers. +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - mc: the module's clock input +- interrupts: The interrupt outputs from the controller. +- #iommu-cells: Should be 1. The single cell of the IOMMU specifier defines + the SWGROUP of the master. + +This device implements an IOMMU that complies with the generic IOMMU binding. +See ../iommu/iommu.txt for details. + +Example: +-------- + + mc: memory-controller@0,70019000 { + compatible = "nvidia,tegra124-mc"; + reg = <0x0 0x70019000 0x0 0x1000>; + clocks = <&tegra_car TEGRA124_CLK_MC>; + clock-names = "mc"; + + interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; + + #iommu-cells = <1>; + }; + + sdhci@0,700b0000 { + compatible = "nvidia,tegra124-sdhci"; + ... + iommus = <&mc TEGRA_SWGROUP_SDMMC1A>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/synopsys.txt b/Documentation/devicetree/bindings/memory-controllers/synopsys.txt new file mode 100644 index 000000000000..f9c6454146b6 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/synopsys.txt @@ -0,0 +1,11 @@ +Binding for Synopsys IntelliDDR Multi Protocol Memory Controller + +Required properties: + - compatible: Should be 'xlnx,zynq-ddrc-a05' + - reg: Base address and size of the controllers memory area + +Example: + memory-controller@f8006000 { + compatible = "xlnx,zynq-ddrc-a05"; + reg = <0xf8006000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt b/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt new file mode 100644 index 000000000000..9592717f483f --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt @@ -0,0 +1,210 @@ +* Device tree bindings for Texas instruments AEMIF controller + +The Async External Memory Interface (EMIF16/AEMIF) controller is intended to +provide a glue-less interface to a variety of asynchronous memory devices like +ASRA M, NOR and NAND memory. A total of 256M bytes of any of these memories +can be accessed at any given time via four chip selects with 64M byte access +per chip select. Synchronous memories such as DDR1 SD RAM, SDR SDRAM +and Mobile SDR are not supported. + +Documentation: +Davinci DM646x - http://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf +OMAP-L138 (DA850) - http://www.ti.com/lit/ug/spruh77a/spruh77a.pdf +Kestone - http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf + +Required properties: + +- compatible: "ti,davinci-aemif" + "ti,keystone-aemif" + "ti,da850-aemif" + +- reg: contains offset/length value for AEMIF control registers + space. + +- #address-cells: Must be 2. The partition number has to be encoded in the + first address cell and it may accept values 0..N-1 + (N - total number of partitions). It's recommended to + assign N-1 number for the control partition. The second + cell is the offset into the partition. + +- #size-cells: Must be set to 1. + +- ranges: Contains memory regions. There are two types of + ranges/partitions: + - CS-specific partition/range. If continuous, must be + set up to reflect the memory layout for 4 chipselects, + if not then additional range/partition can be added and + child device can select the proper one. + - control partition which is common for all CS + interfaces. + +- clocks: the clock feeding the controller clock. Required only + if clock tree data present in device tree. + See clock-bindings.txt + +- clock-names: clock name. It has to be "aemif". Required only if clock + tree data present in device tree, in another case don't + use it. + See clock-bindings.txt + +- clock-ranges: Empty property indicating that child nodes can inherit + named clocks. Required only if clock tree data present + in device tree. + See clock-bindings.txt + + +Child chip-select (cs) nodes contain the memory devices nodes connected to +such as NOR (e.g. cfi-flash) and NAND (ti,davinci-nand, see davinci-nand.txt). +There might be board specific devices like FPGAs. + +Required child cs node properties: + +- #address-cells: Must be 2. + +- #size-cells: Must be 1. + +- ranges: Empty property indicating that child nodes can inherit + memory layout. + +- clock-ranges: Empty property indicating that child nodes can inherit + named clocks. Required only if clock tree data present + in device tree. + +- ti,cs-chipselect: number of chipselect. Indicates on the aemif driver + which chipselect is used for accessing the memory. For + compatibles "ti,davinci-aemif" and "ti,keystone-aemif" + it can be in range [0-3]. For compatible + "ti,da850-aemif" range is [2-5]. + +Optional child cs node properties: + +- ti,cs-bus-width: width of the asynchronous device's data bus + 8 or 16 if not preset 8 + +- ti,cs-select-strobe-mode: enable/disable select strobe mode + In select strobe mode chip select behaves as + the strobe and is active only during the strobe + period. If present then enable. + +- ti,cs-extended-wait-mode: enable/disable extended wait mode + if set, the controller monitors the EMIFWAIT pin + mapped to that chip select to determine if the + device wants to extend the strobe period. If + present then enable. + +- ti,cs-min-turnaround-ns: minimum turn around time, ns + Time between the end of one asynchronous memory + access and the start of another asynchronous + memory access. This delay is not incurred + between a read followed by read or a write + followed by a write to same chip select. + +- ti,cs-read-setup-ns: read setup width, ns + Time between the beginning of a memory cycle + and the activation of read strobe. + Minimum value is 1 (0 treated as 1). + +- ti,cs-read-strobe-ns: read strobe width, ns + Time between the activation and deactivation of + the read strobe. + Minimum value is 1 (0 treated as 1). + +- ti,cs-read-hold-ns: read hold width, ns + Time between the deactivation of the read + strobe and the end of the cycle (which may be + either an address change or the deactivation of + the chip select signal. + Minimum value is 1 (0 treated as 1). + +- ti,cs-write-setup-ns: write setup width, ns + Time between the beginning of a memory cycle + and the activation of write strobe. + Minimum value is 1 (0 treated as 1). + +- ti,cs-write-strobe-ns: write strobe width, ns + Time between the activation and deactivation of + the write strobe. + Minimum value is 1 (0 treated as 1). + +- ti,cs-write-hold-ns: write hold width, ns + Time between the deactivation of the write + strobe and the end of the cycle (which may be + either an address change or the deactivation of + the chip select signal. + Minimum value is 1 (0 treated as 1). + +If any of the above parameters are absent, current parameter value will be taken +from the corresponding HW reg. + +Example for aemif, davinci nand and nor flash chip select shown below. + +memory-controller@21000A00 { + compatible = "ti,davinci-aemif"; + #address-cells = <2>; + #size-cells = <1>; + clocks = <&clkaemif 0>; + clock-names = "aemif"; + clock-ranges; + reg = <0x21000A00 0x00000100>; + ranges = <0 0 0x70000000 0x10000000 + 1 0 0x21000A00 0x00000100>; + /* + * Partition0: CS-specific memory range which is + * implemented as continuous physical memory region + * Partition1: control memory range + */ + + nand:cs2 { + #address-cells = <2>; + #size-cells = <1>; + clock-ranges; + ranges; + + ti,cs-chipselect = <2>; + /* all timings in nanoseconds */ + ti,cs-min-turnaround-ns = <0>; + ti,cs-read-hold-ns = <7>; + ti,cs-read-strobe-ns = <42>; + ti,cs-read-setup-ns = <14>; + ti,cs-write-hold-ns = <7>; + ti,cs-write-strobe-ns = <42>; + ti,cs-write-setup-ns = <14>; + + nand@0,0x8000000 { + compatible = "ti,davinci-nand"; + reg = <0 0x8000000 0x4000000 + 1 0x0000000 0x0000100>; + /* + * Partition0, offset 0x8000000, size 0x4000000 + * Partition1, offset 0x0000000, size 0x0000100 + */ + + .. see davinci-nand.txt + }; + }; + + nor:cs0 { + #address-cells = <2>; + #size-cells = <1>; + clock-ranges; + ranges; + + ti,cs-chipselect = <0>; + /* all timings in nanoseconds */ + ti,cs-min-turnaround-ns = <0>; + ti,cs-read-hold-ns = <8>; + ti,cs-read-strobe-ns = <40>; + ti,cs-read-setup-ns = <14>; + ti,cs-write-hold-ns = <7>; + ti,cs-write-strobe-ns = <40>; + ti,cs-write-setup-ns = <14>; + ti,cs-bus-width = <16>; + + flash@0,0x0000000 { + compatible = "cfi-flash"; + reg = <0 0x0000000 0x4000000>; + + ... + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/arizona.txt b/Documentation/devicetree/bindings/mfd/arizona.txt index 0e295c9d8937..7bd1273f571a 100644 --- a/Documentation/devicetree/bindings/mfd/arizona.txt +++ b/Documentation/devicetree/bindings/mfd/arizona.txt @@ -5,9 +5,10 @@ of analogue I/O. Required properties: - - compatible : one of the following chip-specific strings: - "wlf,wm5102" - "wlf,wm5110" + - compatible : One of the following chip-specific strings: + "wlf,wm5102" + "wlf,wm5110" + "wlf,wm8997" - reg : I2C slave address when connected using I2C, chip select number when using SPI. @@ -25,8 +26,9 @@ Required properties: - #gpio-cells : Must be 2. The first cell is the pin number and the second cell is used to specify optional parameters (currently unused). - - AVDD1-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply, CPVDD-supply, - SPKVDDL-supply, SPKVDDR-supply : power supplies for the device, as covered + - AVDD-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply (wm5102, wm5110), + CPVDD-supply, SPKVDDL-supply (wm5102, wm5110), SPKVDDR-supply (wm5102, + wm5110), SPKVDD-supply (wm8997) : Power supplies for the device, as covered in Documentation/devicetree/bindings/regulator/regulator.txt Optional properties: @@ -40,12 +42,30 @@ Optional properties: the chip default will be used. If present exactly five values must be specified. + - wlf,inmode : A list of INn_MODE register values, where n is the number + of input signals. Valid values are 0 (Differential), 1 (Single-ended) and + 2 (Digital Microphone). If absent, INn_MODE registers set to 0 by default. + If present, values must be specified less than or equal to the number of + input singals. If values less than the number of input signals, elements + that has not been specifed are set to 0 by default. + + - DCVDD-supply, MICVDD-supply : Power supplies, only need to be specified if + they are being externally supplied. As covered in + Documentation/devicetree/bindings/regulator/regulator.txt + +Optional subnodes: + - ldo1 : Initial data for the LDO1 regulator, as covered in + Documentation/devicetree/bindings/regulator/regulator.txt + - micvdd : Initial data for the MICVDD regulator, as covered in + Documentation/devicetree/bindings/regulator/regulator.txt + Example: codec: wm5102@1a { compatible = "wlf,wm5102"; reg = <0x1a>; interrupts = <347>; + interrupt-controller; #interrupt-cells = <2>; interrupt-parent = <&gic>; @@ -53,10 +73,10 @@ codec: wm5102@1a { #gpio-cells = <2>; wlf,gpio-defaults = < - 0x00000000, /* AIF1TXLRCLK */ - 0xffffffff, - 0xffffffff, - 0xffffffff, - 0xffffffff, + 0x00000000 /* AIF1TXLRCLK */ + 0xffffffff + 0xffffffff + 0xffffffff + 0xffffffff >; }; diff --git a/Documentation/devicetree/bindings/mfd/as3722.txt b/Documentation/devicetree/bindings/mfd/as3722.txt index 8edcb9bd873b..4f64b2a73169 100644 --- a/Documentation/devicetree/bindings/mfd/as3722.txt +++ b/Documentation/devicetree/bindings/mfd/as3722.txt @@ -13,6 +13,14 @@ Required properties: The second cell is the flags, encoded as the trigger masks from binding document interrupts.txt, using dt-bindings/irq. +Optional properties: +-------------------- +- ams,enable-internal-int-pullup: Boolean property, to enable internal pullup on + interrupt pin. Missing this will disable internal pullup on INT pin. +- ams,enable-internal-i2c-pullup: Boolean property, to enable internal pullup on + i2c scl/sda pins. Missing this will disable internal pullup on i2c + scl/sda lines. + Optional submodule and their properties: ======================================= diff --git a/Documentation/devicetree/bindings/mfd/atmel-gpbr.txt b/Documentation/devicetree/bindings/mfd/atmel-gpbr.txt new file mode 100644 index 000000000000..a28569540683 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/atmel-gpbr.txt @@ -0,0 +1,15 @@ +* Device tree bindings for Atmel GPBR (General Purpose Backup Registers) + +The GPBR are a set of battery-backed registers. + +Required properties: +- compatible: "atmel,at91sam9260-gpbr", "syscon" +- reg: contains offset/length value of the GPBR memory + region. + +Example: + +gpbr: gpbr@fffffd50 { + compatible = "atmel,at91sam9260-gpbr", "syscon"; + reg = <0xfffffd50 0x10>; +}; diff --git a/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt b/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt new file mode 100644 index 000000000000..f64de95a8e8b --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt @@ -0,0 +1,51 @@ +Device-Tree bindings for Atmel's HLCDC (High LCD Controller) MFD driver + +Required properties: + - compatible: value should be one of the following: + "atmel,sama5d3-hlcdc" + - reg: base address and size of the HLCDC device registers. + - clock-names: the name of the 3 clocks requested by the HLCDC device. + Should contain "periph_clk", "sys_clk" and "slow_clk". + - clocks: should contain the 3 clocks requested by the HLCDC device. + - interrupts: should contain the description of the HLCDC interrupt line + +The HLCDC IP exposes two subdevices: + - a PWM chip: see ../pwm/atmel-hlcdc-pwm.txt + - a Display Controller: see ../drm/atmel-hlcdc-dc.txt + +Example: + + hlcdc: hlcdc@f0030000 { + compatible = "atmel,sama5d3-hlcdc"; + reg = <0xf0030000 0x2000>; + clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>; + clock-names = "periph_clk","sys_clk", "slow_clk"; + interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>; + status = "disabled"; + + hlcdc-display-controller { + compatible = "atmel,hlcdc-display-controller"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888>; + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + hlcdc_panel_output: endpoint@0 { + reg = <0>; + remote-endpoint = <&panel_input>; + }; + }; + }; + + hlcdc_pwm: hlcdc-pwm { + compatible = "atmel,hlcdc-pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_pwm>; + #pwm-cells = <3>; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/bcm590xx.txt b/Documentation/devicetree/bindings/mfd/bcm590xx.txt new file mode 100644 index 000000000000..be51a15e05f9 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/bcm590xx.txt @@ -0,0 +1,39 @@ +------------------------------- +BCM590xx Power Management Units +------------------------------- + +Required properties: +- compatible: "brcm,bcm59056" +- reg: I2C slave address +- interrupts: interrupt for the PMU. Generic interrupt client node bindings + are described in interrupt-controller/interrupts.txt + +------------------ +Voltage Regulators +------------------ + +Optional child nodes: +- regulators: container node for regulators following the generic + regulator binding in regulator/regulator.txt + + The valid regulator node names for BCM59056 are: + rfldo, camldo1, camldo2, simldo1, simldo2, sdldo, sdxldo, + mmcldo1, mmcldo2, audldo, micldo, usbldo, vibldo, + csr, iosr1, iosr2, msr, sdsr1, sdsr2, vsr, + gpldo1, gpldo2, gpldo3, gpldo4, gpldo5, gpldo6, + vbus + +Example: + pmu: bcm59056@8 { + compatible = "brcm,bcm59056"; + reg = <0x08>; + interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>; + regulators { + rfldo_reg: rfldo { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + ... + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/bfticu.txt b/Documentation/devicetree/bindings/mfd/bfticu.txt new file mode 100644 index 000000000000..65c90776c620 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/bfticu.txt @@ -0,0 +1,25 @@ +KEYMILE bfticu Chassis Management FPGA + +The bfticu is a multifunction device that manages the whole chassis. +Its main functionality is to collect IRQs from the whole chassis and signals +them to a single controller. + +Required properties: +- compatible: "keymile,bfticu" +- interrupt-controller: the bfticu FPGA is an interrupt controller +- interrupts: the main IRQ line to signal the collected IRQs +- #interrupt-cells : is 2 and their usage is compliant to the 2 cells variant + of Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +- interrupt-parent: the parent IRQ ctrl the main IRQ is connected to +- reg: access on the parent local bus (chip select, offset in chip select, size) + +Example: + + chassis-mgmt@3,0 { + compatible = "keymile,bfticu"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <3 0 0x100>; + interrupt-parent = <&mpic>; + interrupts = <6 1 0 0>; + }; diff --git a/Documentation/devicetree/bindings/mfd/da9055.txt b/Documentation/devicetree/bindings/mfd/da9055.txt new file mode 100644 index 000000000000..6dab34d34fce --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/da9055.txt @@ -0,0 +1,72 @@ +* Dialog DA9055 Power Management Integrated Circuit (PMIC) + +DA9055 consists of a large and varied group of sub-devices (I2C Only): + +Device Supply Names Description +------ ------------ ----------- +da9055-gpio : : GPIOs +da9055-regulator : : Regulators +da9055-onkey : : On key +da9055-rtc : : RTC +da9055-hwmon : : ADC +da9055-watchdog : : Watchdog + +The CODEC device in DA9055 has a separate, configurable I2C address and so +is instantiated separately from the PMIC. + +For details on accompanying CODEC I2C device, see the following: +Documentation/devicetree/bindings/sound/da9055.txt + +====== + +Required properties: +- compatible : Should be "dlg,da9055-pmic" +- reg: Specifies the I2C slave address (defaults to 0x5a but can be modified) +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the IRQs from da9055 are delivered to. +- interrupts: IRQ line info for da9055 chip. +- interrupt-controller: da9055 has internal IRQs (has own IRQ domain). +- #interrupt-cells: Should be 1, is the local IRQ number for da9055. + +Sub-nodes: +- regulators : Contain the regulator nodes. The DA9055 regulators are + bound using their names as listed below: + + buck1 : regulator BUCK1 + buck2 : regulator BUCK2 + ldo1 : regulator LDO1 + ldo2 : regulator LDO2 + ldo3 : regulator LDO3 + ldo4 : regulator LDO4 + ldo5 : regulator LDO5 + ldo6 : regulator LDO6 + + The bindings details of individual regulator device can be found in: + Documentation/devicetree/bindings/regulator/regulator.txt + + +Example: + + pmic: da9055-pmic@5a { + compatible = "dlg,da9055-pmic"; + reg = <0x5a>; + interrupt-parent = <&intc>; + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + + regulators { + buck1: BUCK1 { + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <2075000>; + }; + buck2: BUCK2 { + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <2500000>; + }; + ldo1: LDO1 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/hi6421.txt b/Documentation/devicetree/bindings/mfd/hi6421.txt new file mode 100644 index 000000000000..0d5a4466a494 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/hi6421.txt @@ -0,0 +1,38 @@ +* HI6421 Multi-Functional Device (MFD), by HiSilicon Ltd. + +Required parent device properties: +- compatible : contains "hisilicon,hi6421-pmic"; +- reg : register range space of hi6421; + +Supported Hi6421 sub-devices include: + +Device IRQ Names Supply Names Description +------ --------- ------------ ----------- +regulators : None : None : Regulators + +Required child device properties: +None. + +Example: + hi6421 { + compatible = "hisilicon,hi6421-pmic"; + reg = <0xfcc00000 0x0180>; /* 0x60 << 2 */ + + regulators { + // supply for MLC NAND/ eMMC + hi6421_vout0_reg: hi6421_vout0 { + regulator-name = "VOUT0"; + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + + // supply for 26M Oscillator + hi6421_vout1_reg: hi6421_vout1 { + regulator-name = "VOUT1"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <2000000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/max14577.txt b/Documentation/devicetree/bindings/mfd/max14577.txt new file mode 100644 index 000000000000..236264c10b92 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max14577.txt @@ -0,0 +1,146 @@ +Maxim MAX14577/77836 Multi-Function Device + +MAX14577 is a Multi-Function Device with Micro-USB Interface Circuit, Li+ +Battery Charger and SFOUT LDO output for powering USB devices. It is +interfaced to host controller using I2C. + +MAX77836 additionally contains PMIC (with two LDO regulators) and Fuel Gauge. + + +Required properties: +- compatible : Must be "maxim,max14577" or "maxim,max77836". +- reg : I2C slave address for the max14577 chip (0x25 for max14577/max77836) +- interrupts : IRQ line for the chip. +- interrupt-parent : The parent interrupt controller. + + +Required nodes: + - charger : + Node for configuring the charger driver. + Required properties: + - compatible : "maxim,max14577-charger" + or "maxim,max77836-charger" + - maxim,fast-charge-uamp : Current in uA for Fast Charge; + Valid values: + - for max14577: 90000 - 950000; + - for max77836: 45000 - 475000; + - maxim,eoc-uamp : Current in uA for End-Of-Charge mode; + Valid values: + - for max14577: 50000 - 200000; + - for max77836: 5000 - 100000; + - maxim,ovp-uvolt : OverVoltage Protection Threshold in uV; + In an overvoltage condition, INT asserts and charging + stops. Valid values: + - 6000000, 6500000, 7000000, 7500000; + - maxim,constant-uvolt : Battery Constant Voltage in uV; + Valid values: + - 4000000 - 4280000 (step by 20000); + - 4350000; + + +Optional nodes: +- max14577-muic/max77836-muic : + Node used only by extcon consumers. + Required properties: + - compatible : "maxim,max14577-muic" or "maxim,max77836-muic" + +- regulators : + Required properties: + - compatible : "maxim,max14577-regulator" + or "maxim,max77836-regulator" + + May contain a sub-node per regulator from the list below. Each + sub-node should contain the constraints and initialization information + for that regulator. See regulator.txt for a description of standard + properties for these sub-nodes. + + List of valid regulator names: + - for max14577: CHARGER, SAFEOUT. + - for max77836: CHARGER, SAFEOUT, LDO1, LDO2. + + The SAFEOUT is a fixed voltage regulator so there is no need to specify + voltages for it. + + +Example: + +#include <dt-bindings/interrupt-controller/irq.h> + +max14577@25 { + compatible = "maxim,max14577"; + reg = <0x25>; + interrupt-parent = <&gpx1>; + interrupts = <5 IRQ_TYPE_NONE>; + + muic: max14577-muic { + compatible = "maxim,max14577-muic"; + }; + + regulators { + compatible = "maxim,max14577-regulator"; + + SAFEOUT { + regulator-name = "SAFEOUT"; + }; + CHARGER { + regulator-name = "CHARGER"; + regulator-min-microamp = <90000>; + regulator-max-microamp = <950000>; + regulator-boot-on; + }; + }; + + charger { + compatible = "maxim,max14577-charger"; + + maxim,constant-uvolt = <4350000>; + maxim,fast-charge-uamp = <450000>; + maxim,eoc-uamp = <50000>; + maxim,ovp-uvolt = <6500000>; + }; +}; + + +max77836@25 { + compatible = "maxim,max77836"; + reg = <0x25>; + interrupt-parent = <&gpx1>; + interrupts = <5 IRQ_TYPE_NONE>; + + muic: max77836-muic { + compatible = "maxim,max77836-muic"; + }; + + regulators { + compatible = "maxim,max77836-regulator"; + + SAFEOUT { + regulator-name = "SAFEOUT"; + }; + CHARGER { + regulator-name = "CHARGER"; + regulator-min-microamp = <90000>; + regulator-max-microamp = <950000>; + regulator-boot-on; + }; + LDO1 { + regulator-name = "LDO1"; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; + LDO2 { + regulator-name = "LDO2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3950000>; + }; + }; + + charger { + compatible = "maxim,max77836-charger"; + + maxim,constant-uvolt = <4350000>; + maxim,fast-charge-uamp = <225000>; + maxim,eoc-uamp = <7500>; + maxim,ovp-uvolt = <6500000>; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/max77686.txt b/Documentation/devicetree/bindings/mfd/max77686.txt index 678f3cf0b8f0..75fdfaf41831 100644 --- a/Documentation/devicetree/bindings/mfd/max77686.txt +++ b/Documentation/devicetree/bindings/mfd/max77686.txt @@ -34,6 +34,12 @@ to get matched with their hardware counterparts as follow: -BUCKn : for BUCKs, where n can lie in range 1 to 9. example: BUCK1, BUCK5, BUCK9. + Regulators which can be turned off during system suspend: + -LDOn : 2, 6-8, 10-12, 14-16, + -BUCKn : 1-4. + Use standard regulator bindings for it ('regulator-off-in-suspend'). + + Example: max77686@09 { diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt index 11921cc417bf..01e9f30fe678 100644 --- a/Documentation/devicetree/bindings/mfd/max77693.txt +++ b/Documentation/devicetree/bindings/mfd/max77693.txt @@ -27,6 +27,20 @@ Optional properties: [*] refer Documentation/devicetree/bindings/regulator/regulator.txt +- haptic : The MAX77693 haptic device utilises a PWM controlled motor to provide + users with tactile feedback. PWM period and duty-cycle are varied in + order to provide the approprite level of feedback. + + Required properties: + - compatible : Must be "maxim,max77693-hpatic" + - haptic-supply : power supply for the haptic motor + [*] refer Documentation/devicetree/bindings/regulator/regulator.txt + - pwms : phandle to the physical PWM(Pulse Width Modulation) device. + PWM properties should be named "pwms". And number of cell is different + for each pwm device. + To get more informations, please refer to documentaion. + [*] refer Documentation/devicetree/bindings/pwm/pwm.txt + Example: max77693@66 { compatible = "maxim,max77693"; @@ -52,4 +66,11 @@ Example: regulator-boot-on; }; }; + + haptic { + compatible = "maxim,max77693-haptic"; + haptic-supply = <&haptic_supply>; + pwms = <&pwm 0 40000 0>; + pwm-names = "haptic"; + }; }; diff --git a/Documentation/devicetree/bindings/mfd/mc13xxx.txt b/Documentation/devicetree/bindings/mfd/mc13xxx.txt index abd9e3cb2db7..8aba48821a85 100644 --- a/Documentation/devicetree/bindings/mfd/mc13xxx.txt +++ b/Documentation/devicetree/bindings/mfd/mc13xxx.txt @@ -10,9 +10,47 @@ Optional properties: - fsl,mc13xxx-uses-touch : Indicate the touchscreen controller is being used Sub-nodes: +- codec: Contain the Audio Codec node. + - adc-port: Contain PMIC SSI port number used for ADC. + - dac-port: Contain PMIC SSI port number used for DAC. +- leds : Contain the led nodes and initial register values in property + "led-control". Number of register depends of used IC, for MC13783 is 6, + for MC13892 is 4, for MC34708 is 1. See datasheet for bits definitions of + these registers. + - #address-cells: Must be 1. + - #size-cells: Must be 0. + Each led node should contain "reg", which used as LED ID (described below). + Optional properties "label" and "linux,default-trigger" is described in + Documentation/devicetree/bindings/leds/common.txt. - regulators : Contain the regulator nodes. The regulators are bound using their names as listed below with their registers and bits for enabling. +MC13783 LED IDs: + 0 : Main display + 1 : AUX display + 2 : Keypad + 3 : Red 1 + 4 : Green 1 + 5 : Blue 1 + 6 : Red 2 + 7 : Green 2 + 8 : Blue 2 + 9 : Red 3 + 10 : Green 3 + 11 : Blue 3 + +MC13892 LED IDs: + 0 : Main display + 1 : AUX display + 2 : Keypad + 3 : Red + 4 : Green + 5 : Blue + +MC34708 LED IDs: + 0 : Charger Red + 1 : Charger Green + MC13783 regulators: sw1a : regulator SW1A (register 24, bit 0) sw1b : regulator SW1B (register 25, bit 0) @@ -89,6 +127,18 @@ ecspi@70010000 { /* ECSPI1 */ interrupt-parent = <&gpio0>; interrupts = <8>; + leds { + #address-cells = <1>; + #size-cells = <0>; + led-control = <0x000 0x000 0x0e0 0x000>; + + sysled { + reg = <3>; + label = "system:red:live"; + linux,default-trigger = "heartbeat"; + }; + }; + regulators { sw1_reg: mc13892__sw1 { regulator-min-microvolt = <600000>; diff --git a/Documentation/devicetree/bindings/mfd/omap-usb-host.txt b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt index b381fa696bf9..4721b2d521e4 100644 --- a/Documentation/devicetree/bindings/mfd/omap-usb-host.txt +++ b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt @@ -32,6 +32,29 @@ Optional properties: - single-ulpi-bypass: Must be present if the controller contains a single ULPI bypass control bit. e.g. OMAP3 silicon <= ES2.1 +- clocks: a list of phandles and clock-specifier pairs, one for each entry in + clock-names. + +- clock-names: should include: + For OMAP3 + * "usbhost_120m_fck" - 120MHz Functional clock. + + For OMAP4+ + * "refclk_60m_int" - 60MHz internal reference clock for UTMI clock mux + * "refclk_60m_ext_p1" - 60MHz external ref. clock for Port 1's UTMI clock mux. + * "refclk_60m_ext_p2" - 60MHz external ref. clock for Port 2's UTMI clock mux + * "utmi_p1_gfclk" - Port 1 UTMI clock mux. + * "utmi_p2_gfclk" - Port 2 UTMI clock mux. + * "usb_host_hs_utmi_p1_clk" - Port 1 UTMI clock gate. + * "usb_host_hs_utmi_p2_clk" - Port 2 UTMI clock gate. + * "usb_host_hs_utmi_p3_clk" - Port 3 UTMI clock gate. + * "usb_host_hs_hsic480m_p1_clk" - Port 1 480MHz HSIC clock gate. + * "usb_host_hs_hsic480m_p2_clk" - Port 2 480MHz HSIC clock gate. + * "usb_host_hs_hsic480m_p3_clk" - Port 3 480MHz HSIC clock gate. + * "usb_host_hs_hsic60m_p1_clk" - Port 1 60MHz HSIC clock gate. + * "usb_host_hs_hsic60m_p2_clk" - Port 2 60MHz HSIC clock gate. + * "usb_host_hs_hsic60m_p3_clk" - Port 3 60MHz HSIC clock gate. + Required properties if child node exists: - #address-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt b/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt index 62fe69724e3b..c58d70437fce 100644 --- a/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt +++ b/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt @@ -7,6 +7,16 @@ Required properties: - interrupts : should contain the TLL module's interrupt - ti,hwmod : must contain "usb_tll_hs" +Optional properties: + +- clocks: a list of phandles and clock-specifier pairs, one for each entry in + clock-names. + +- clock-names: should include: + * "usb_tll_hs_usb_ch0_clk" - USB TLL channel 0 clock + * "usb_tll_hs_usb_ch1_clk" - USB TLL channel 1 clock + * "usb_tll_hs_usb_ch2_clk" - USB TLL channel 2 clock + Example: usbhstll: usbhstll@4a062000 { diff --git a/Documentation/devicetree/bindings/mfd/palmas.txt b/Documentation/devicetree/bindings/mfd/palmas.txt index e5f0f8303461..eda898978d33 100644 --- a/Documentation/devicetree/bindings/mfd/palmas.txt +++ b/Documentation/devicetree/bindings/mfd/palmas.txt @@ -6,6 +6,7 @@ twl6037 (palmas) tps65913 (palmas) tps65914 (palmas) tps659038 +tps65917 Required properties: - compatible : Should be from the list @@ -16,6 +17,7 @@ Required properties: ti,tps65914 ti,tps80036 ti,tps659038 + ti,tps65917 and also the generic series names ti,palmas - interrupt-controller : palmas has its own internal IRQs diff --git a/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt b/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt new file mode 100644 index 000000000000..7182b8857f57 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt @@ -0,0 +1,64 @@ + Qualcomm SPMI PMICs multi-function device bindings + +The Qualcomm SPMI series presently includes PM8941, PM8841 and PMA8084 +PMICs. These PMICs use a QPNP scheme through SPMI interface. +QPNP is effectively a partitioning scheme for dividing the SPMI extended +register space up into logical pieces, and set of fixed register +locations/definitions within these regions, with some of these regions +specifically used for interrupt handling. + +The QPNP PMICs are used with the Qualcomm Snapdragon series SoCs, and are +interfaced to the chip via the SPMI (System Power Management Interface) bus. +Support for multiple independent functions are implemented by splitting the +16-bit SPMI slave address space into 256 smaller fixed-size regions, 256 bytes +each. A function can consume one or more of these fixed-size register regions. + +Required properties: +- compatible: Should contain one of: + "qcom,pm8941" + "qcom,pm8841" + "qcom,pma8084" + or generalized "qcom,spmi-pmic". +- reg: Specifies the SPMI USID slave address for this device. + For more information see: + Documentation/devicetree/bindings/spmi/spmi.txt + +Required properties for peripheral child nodes: +- compatible: Should contain "qcom,xxx", where "xxx" is a peripheral name. + +Optional properties for peripheral child nodes: +- interrupts: Interrupts are specified as a 4-tuple. For more information + see: + Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt +- interrupt-names: Corresponding interrupt name to the interrupts property + +Each child node of SPMI slave id represents a function of the PMIC. In the +example below the rtc device node represents a peripheral of pm8941 +SID = 0. The regulator device node represents a peripheral of pm8941 SID = 1. + +Example: + + spmi { + compatible = "qcom,spmi-pmic-arb"; + + pm8941@0 { + compatible = "qcom,pm8941", "qcom,spmi-pmic"; + reg = <0x0 SPMI_USID>; + + rtc { + compatible = "qcom,rtc"; + interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "alarm"; + }; + }; + + pm8941@1 { + compatible = "qcom,pm8941", "qcom,spmi-pmic"; + reg = <0x1 SPMI_USID>; + + regulator { + compatible = "qcom,regulator"; + regulator-name = "8941_boost"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt new file mode 100644 index 000000000000..f24f33409164 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt @@ -0,0 +1,97 @@ +Qualcomm PM8xxx PMIC multi-function devices + +The PM8xxx family of Power Management ICs are used to provide regulated +voltages and other various functionality to Qualcomm SoCs. + += PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,pm8058" + "qcom,pm8921" + +- #address-cells: + Usage: required + Value type: <u32> + Definition: must be 1 + +- #size-cells: + Usage: required + Value type: <u32> + Definition: must be 0 + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: specifies the interrupt that indicates a subdevice + has generated an interrupt (summary interrupt). The + format of the specifier is defined by the binding document + describing the node's interrupt parent. + +- #interrupt-cells: + Usage: required + Value type : <u32> + Definition: must be 2. Specifies the number of cells needed to encode + an interrupt source. The 1st cell contains the interrupt + number. The 2nd cell is the trigger type and level flags + encoded as follows: + + 1 = low-to-high edge triggered + 2 = high-to-low edge triggered + 4 = active high level-sensitive + 8 = active low level-sensitive + +- interrupt-controller: + Usage: required + Value type: <empty> + Definition: identifies this node as an interrupt controller + += SUBCOMPONENTS + +The PMIC contains multiple independent functions, each described in a subnode. +The below bindings specify the set of valid subnodes. + +== Real-Time Clock + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,pm8058-rtc" + "qcom,pm8921-rtc" + "qcom,pm8941-rtc" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: single entry specifying the base address of the RTC registers + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: single entry specifying the RTC's alarm interrupt + +- allow-set-time: + Usage: optional + Value type: <empty> + Definition: indicates that the setting of RTC time is allowed by + the host CPU + += EXAMPLE + + pmicintc: pmic@0 { + compatible = "qcom,pm8921"; + interrupts = <104 8>; + #interrupt-cells = <2>; + interrupt-controller; + #address-cells = <1>; + #size-cells = <0>; + + rtc@11d { + compatible = "qcom,pm8921-rtc"; + reg = <0x11d>; + interrupts = <0x27 0>; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/qriox.txt b/Documentation/devicetree/bindings/mfd/qriox.txt new file mode 100644 index 000000000000..f301e2d4ce76 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/qriox.txt @@ -0,0 +1,17 @@ +KEYMILE qrio Board Control CPLD + +The qrio is a multifunction device that controls the KEYMILE boards based on +the kmp204x design. +It is consists of a reset controller, watchdog timer, LEDs, and 2 IRQ capable +GPIO blocks. + +Required properties: +- compatible: "keymile,qriox" +- reg: access on the parent local bus (chip select, offset in chip select, size) + +Example: + + board-control@1,0 { + compatible = "keymile,qriox"; + reg = <1 0 0x80>; + }; diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt new file mode 100644 index 000000000000..9e6e2592e5c8 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/rk808.txt @@ -0,0 +1,177 @@ +RK808 Power Management Integrated Circuit + +Required properties: +- compatible: "rockchip,rk808" +- reg: I2C slave address +- interrupt-parent: The parent interrupt controller. +- interrupts: the interrupt outputs of the controller. +- #clock-cells: from common clock binding; shall be set to 1 (multiple clock + outputs). See <dt-bindings/clock/rockchip,rk808.h> for clock IDs. + +Optional properties: +- clock-output-names: From common clock binding to override the + default output clock name +- rockchip,system-power-controller: Telling whether or not this pmic is controlling + the system power. +- vcc1-supply: The input supply for DCDC_REG1 +- vcc2-supply: The input supply for DCDC_REG2 +- vcc3-supply: The input supply for DCDC_REG3 +- vcc4-supply: The input supply for DCDC_REG4 +- vcc6-supply: The input supply for LDO_REG1 and LDO_REG2 +- vcc7-supply: The input supply for LDO_REG3 and LDO_REG7 +- vcc8-supply: The input supply for SWITCH_REG1 +- vcc9-supply: The input supply for LDO_REG4 and LDO_REG5 +- vcc10-supply: The input supply for LDO_REG6 +- vcc11-supply: The input supply for LDO_REG8 +- vcc12-supply: The input supply for SWITCH_REG2 + +Regulators: All the regulators of RK808 to be instantiated shall be +listed in a child node named 'regulators'. Each regulator is represented +by a child node of the 'regulators' node. + + regulator-name { + /* standard regulator bindings here */ + }; + +Following regulators of the RK808 PMIC block are supported. Note that +the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO +number as described in RK808 datasheet. + + - DCDC_REGn + - valid values for n are 1 to 4. + - LDO_REGn + - valid values for n are 1 to 8. + - SWITCH_REGn + - valid values for n are 1 to 2 + +Standard regulator bindings are used inside regulator subnodes. Check + Documentation/devicetree/bindings/regulator/regulator.txt +for more details + +Example: + rk808: pmic@1b { + compatible = "rockchip,rk808"; + clock-output-names = "xin32k", "rk808-clkout2"; + interrupt-parent = <&gpio0>; + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int>; + reg = <0x1b>; + rockchip,system-power-controller; + wakeup-source; + #clock-cells = <1>; + + vcc8-supply = <&vcc_18>; + vcc9-supply = <&vcc_io>; + vcc10-supply = <&vcc_io>; + vcc12-supply = <&vcc_io>; + vddio-supply = <&vccio_pmu>; + + regulators { + vdd_cpu: DCDC_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vdd_arm"; + }; + + vdd_gpu: DCDC_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1250000>; + regulator-name = "vdd_gpu"; + }; + + vcc_ddr: DCDC_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_ddr"; + }; + + vcc_io: DCDC_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_io"; + }; + + vccio_pmu: LDO_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vccio_pmu"; + }; + + vcc_tp: LDO_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_tp"; + }; + + vdd_10: LDO_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-name = "vdd_10"; + }; + + vcc18_lcd: LDO_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc18_lcd"; + }; + + vccio_sd: LDO_REG5 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vccio_sd"; + }; + + vdd10_lcd: LDO_REG6 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-name = "vdd10_lcd"; + }; + + vcc_18: LDO_REG7 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc_18"; + }; + + vcca_codec: LDO_REG8 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcca_codec"; + }; + + vcc_wl: SWITCH_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_wl"; + }; + + vcc_lcd: SWITCH_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_lcd"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt new file mode 100644 index 000000000000..937785a3eddc --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt @@ -0,0 +1,36 @@ +* Ricoh RN5T618 PMIC + +Ricoh RN5T618 is a power management IC which integrates 3 step-down +DCDC converters, 7 low-dropout regulators, a Li-ion battery charger, +fuel gauge, ADC, GPIOs and a watchdog timer. It can be controlled +through a I2C interface. + +Required properties: + - compatible: should be "ricoh,rn5t618" + - reg: the I2C slave address of the device + +Sub-nodes: + - regulators: the node is required if the regulator functionality is + needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, LDO1, + LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2. + The common bindings for each individual regulator can be found in: + Documentation/devicetree/bindings/regulator/regulator.txt + +Example: + + pmic@32 { + compatible = "ricoh,rn5t618"; + reg = <0x32>; + + regulators { + DCDC1 { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + }; + + DCDC2 { + regulator-min-microvolt = <1175000>; + regulator-max-microvolt = <1175000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/s2mpa01.txt b/Documentation/devicetree/bindings/mfd/s2mpa01.txt new file mode 100644 index 000000000000..c13d3d8c3947 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/s2mpa01.txt @@ -0,0 +1,90 @@ + +* Samsung S2MPA01 Voltage and Current Regulator + +The Samsung S2MPA01 is a multi-function device which includes high +efficiency buck converters including Dual-Phase buck converter, various LDOs, +and an RTC. It is interfaced to the host controller using an I2C interface. +Each sub-block is addressed by the host system using different I2C slave +addresses. + +Required properties: +- compatible: Should be "samsung,s2mpa01-pmic". +- reg: Specifies the I2C slave address of the PMIC block. It should be 0x66. + +Optional properties: +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from s2mpa01 are delivered to. +- interrupts: An interrupt specifier for the sole interrupt generated by the + device. + +Optional nodes: +- regulators: The regulators of s2mpa01 that have to be instantiated should be + included in a sub-node named 'regulators'. Regulator nodes and constraints + included in this sub-node use the standard regulator bindings which are + documented elsewhere. + +Properties for BUCK regulator nodes: +- regulator-ramp-delay: ramp delay in uV/us. May be 6250, 12500 + (default), 25000, or 50000. May be 0 for disabling the ramp delay on + BUCK{1,2,3,4}. + + In the absence of the regulator-ramp-delay property, the default ramp + delay will be used. + + NOTE: Some BUCKs share the ramp rate setting i.e. same ramp value will be set + for a particular group of BUCKs. So provide same regulator-ramp-delay=<value>. + + The following BUCKs share ramp settings: + * 1 and 6 + * 2 and 4 + * 8, 9, and 10 + +The following are the names of the regulators that the s2mpa01 PMIC block +supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number +as per the datasheet of s2mpa01. + + - LDOn + - valid values for n are 1 to 26 + - Example: LDO1, LD02, LDO26 + - BUCKn + - valid values for n are 1 to 10. + - Example: BUCK1, BUCK2, BUCK9 + +Example: + + s2mpa01_pmic@66 { + compatible = "samsung,s2mpa01-pmic"; + reg = <0x66>; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ALIVE"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + ldo2_reg: LDO2 { + regulator-name = "VDDQ_MMC2"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + buck2_reg: BUCK2 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + regulator-ramp-delay = <50000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt index 15ee89c3cc7b..57a045016fca 100644 --- a/Documentation/devicetree/bindings/mfd/s2mps11.txt +++ b/Documentation/devicetree/bindings/mfd/s2mps11.txt @@ -1,5 +1,5 @@ -* Samsung S2MPS11 Voltage and Current Regulator +* Samsung S2MPS11, S2MPS13, S2MPS14 and S2MPU02 Voltage and Current Regulator The Samsung S2MPS11 is a multi-function device which includes voltage and current regulators, RTC, charger controller and other sub-blocks. It is @@ -7,7 +7,8 @@ interfaced to the host controller using an I2C interface. Each sub-block is addressed by the host system using different I2C slave addresses. Required properties: -- compatible: Should be "samsung,s2mps11-pmic". +- compatible: Should be "samsung,s2mps11-pmic" or "samsung,s2mps13-pmic" + or "samsung,s2mps14-pmic" or "samsung,s2mpu02-pmic". - reg: Specifies the I2C slave address of the pmic block. It should be 0x66. Optional properties: @@ -16,20 +17,25 @@ Optional properties: - interrupts: Interrupt specifiers for interrupt sources. Optional nodes: -- clocks: s2mps11 provides three(AP/CP/BT) buffered 32.768 KHz outputs, so to - register these as clocks with common clock framework instantiate a sub-node - named "clocks". It uses the common clock binding documented in : +- clocks: s2mps11, s2mps13 and s5m8767 provide three(AP/CP/BT) buffered 32.768 + KHz outputs, so to register these as clocks with common clock framework + instantiate a sub-node named "clocks". It uses the common clock binding + documented in : [Documentation/devicetree/bindings/clock/clock-bindings.txt] + The s2mps14 provides two (AP/BT) buffered 32.768 KHz outputs. - #clock-cells: should be 1. - The following is the list of clocks generated by the controller. Each clock is assigned an identifier and client nodes use this identifier to specify the clock which they consume. - Clock ID - ---------------------- - 32KhzAP 0 - 32KhzCP 1 - 32KhzBT 2 + Clock ID Devices + ---------------------------------------------------------- + 32KhzAP 0 S2MPS11, S2MPS13, S2MPS14, S5M8767 + 32KhzCP 1 S2MPS11, S2MPS13, S5M8767 + 32KhzBT 2 S2MPS11, S2MPS13, S2MPS14, S5M8767 + + - compatible: Should be one of: "samsung,s2mps11-clk", "samsung,s2mps13-clk", + "samsung,s2mps14-clk", "samsung,s5m8767-clk" - regulators: The regulators of s2mps11 that have to be instantiated should be included in a sub-node named 'regulators'. Regulator nodes included in this @@ -41,7 +47,7 @@ sub-node should be of the format as listed below. regulator-ramp-delay for BUCKs = [6250/12500/25000(default)/50000] uV/us - BUCK[2/3/4/6] supports disabling ramp delay on hardware, so explictly + BUCK[2/3/4/6] supports disabling ramp delay on hardware, so explicitly regulator-ramp-delay = <0> can be used for them to disable ramp delay. In the absence of the regulator-ramp-delay property, the default ramp delay will be used. @@ -51,6 +57,20 @@ for a particular group of BUCKs. So provide same regulator-ramp-delay<value>. Grouping of BUCKs sharing ramp rate setting is as follow : BUCK[1, 6], BUCK[3, 4], and BUCK[7, 8, 10] +On S2MPS14 the LDO10, LDO11 and LDO12 can be configured to external control +over GPIO. To turn this feature on this property must be added to the regulator +sub-node: + - samsung,ext-control-gpios: GPIO specifier for one GPIO + controlling this regulator (enable/disable); +Example: + LDO12 { + regulator-name = "V_EMMC_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + samsung,ext-control-gpios = <&gpk0 2 0>; + }; + + The regulator constraints inside the regulator nodes use the standard regulator bindings which are documented elsewhere. @@ -59,10 +79,18 @@ supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number as per the datasheet of s2mps11. - LDOn - - valid values for n are 1 to 38 - - Example: LDO1, LD02, LDO28 + - valid values for n are: + - S2MPS11: 1 to 38 + - S2MPS13: 1 to 40 + - S2MPS14: 1 to 25 + - S2MPU02: 1 to 28 + - Example: LDO1, LDO2, LDO28 - BUCKn - - valid values for n are 1 to 10. + - valid values for n are: + - S2MPS11: 1 to 10 + - S2MPS13: 1 to 10 + - S2MPS14: 1 to 5 + - S2MPU02: 1 to 7 - Example: BUCK1, BUCK2, BUCK9 Example: @@ -71,8 +99,9 @@ Example: compatible = "samsung,s2mps11-pmic"; reg = <0x66>; - s2m_osc: clocks{ - #clock-cells = 1; + s2m_osc: clocks { + compatible = "samsung,s2mps11-clk"; + #clock-cells = <1>; clock-output-names = "xx", "yy", "zz"; }; diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt index 56edb5520685..3fb68bfefc8b 100644 --- a/Documentation/devicetree/bindings/mfd/stmpe.txt +++ b/Documentation/devicetree/bindings/mfd/stmpe.txt @@ -13,6 +13,7 @@ Optional properties: - interrupt-parent : Specifies which IRQ controller we're connected to - wakeup-source : Marks the input device as wakable - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024 + - irq-gpio : If present, which GPIO to use for event IRQ Example: diff --git a/Documentation/devicetree/bindings/mfd/sun6i-prcm.txt b/Documentation/devicetree/bindings/mfd/sun6i-prcm.txt new file mode 100644 index 000000000000..03c5a551da55 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/sun6i-prcm.txt @@ -0,0 +1,59 @@ +* Allwinner PRCM (Power/Reset/Clock Management) Multi-Functional Device + +PRCM is an MFD device exposing several Power Management related devices +(like clks and reset controllers). + +Required properties: + - compatible: "allwinner,sun6i-a31-prcm" or "allwinner,sun8i-a23-prcm" + - reg: The PRCM registers range + +The prcm node may contain several subdevices definitions: + - see Documentation/devicetree/clk/sunxi.txt for clock devices + - see Documentation/devicetree/reset/allwinner,sunxi-clock-reset.txt for reset + controller devices + + +Example: + + prcm: prcm@01f01400 { + compatible = "allwinner,sun6i-a31-prcm"; + reg = <0x01f01400 0x200>; + + /* Put subdevices here */ + ar100: ar100_clk { + compatible = "allwinner,sun6i-a31-ar100-clk"; + #clock-cells = <0>; + clocks = <&osc32k>, <&osc24M>, <&pll6>, <&pll6>; + }; + + ahb0: ahb0_clk { + compatible = "fixed-factor-clock"; + #clock-cells = <0>; + clock-div = <1>; + clock-mult = <1>; + clocks = <&ar100_div>; + clock-output-names = "ahb0"; + }; + + apb0: apb0_clk { + compatible = "allwinner,sun6i-a31-apb0-clk"; + #clock-cells = <0>; + clocks = <&ahb0>; + clock-output-names = "apb0"; + }; + + apb0_gates: apb0_gates_clk { + compatible = "allwinner,sun6i-a31-apb0-gates-clk"; + #clock-cells = <1>; + clocks = <&apb0>; + clock-output-names = "apb0_pio", "apb0_ir", + "apb0_timer01", "apb0_p2wi", + "apb0_uart", "apb0_1wire", + "apb0_i2c"; + }; + + apb0_rst: apb0_rst { + compatible = "allwinner,sun6i-a31-clock-reset"; + #reset-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/tc3589x.txt b/Documentation/devicetree/bindings/mfd/tc3589x.txt new file mode 100644 index 000000000000..6fcedba46ae9 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/tc3589x.txt @@ -0,0 +1,107 @@ +* Toshiba TC3589x multi-purpose expander + +The Toshiba TC3589x series are I2C-based MFD devices which may expose the +following built-in devices: gpio, keypad, rotator (vibrator), PWM (for +e.g. LEDs or vibrators) The included models are: + +- TC35890 +- TC35892 +- TC35893 +- TC35894 +- TC35895 +- TC35896 + +Required properties: + - compatible : must be "toshiba,tc35890", "toshiba,tc35892", "toshiba,tc35893", + "toshiba,tc35894", "toshiba,tc35895" or "toshiba,tc35896" + - reg : I2C address of the device + - interrupt-parent : specifies which IRQ controller we're connected to + - interrupts : the interrupt on the parent the controller is connected to + - interrupt-controller : marks the device node as an interrupt controller + - #interrupt-cells : should be <1>, the first cell is the IRQ offset on this + TC3589x interrupt controller. + +Optional nodes: + +- GPIO + This GPIO module inside the TC3589x has 24 (TC35890, TC35892) or 20 + (other models) GPIO lines. + - compatible : must be "toshiba,tc3589x-gpio" + - interrupts : interrupt on the parent, which must be the tc3589x MFD device + - interrupt-controller : marks the device node as an interrupt controller + - #interrupt-cells : should be <2>, the first cell is the IRQ offset on this + TC3589x GPIO interrupt controller, the second cell is the interrupt flags + in accordance with <dt-bindings/interrupt-controller/irq.h>. The following + flags are valid: + - IRQ_TYPE_LEVEL_LOW + - IRQ_TYPE_LEVEL_HIGH + - IRQ_TYPE_EDGE_RISING + - IRQ_TYPE_EDGE_FALLING + - IRQ_TYPE_EDGE_BOTH + - gpio-controller : marks the device node as a GPIO controller + - #gpio-cells : should be <2>, the first cell is the GPIO offset on this + GPIO controller, the second cell is the flags. + +- Keypad + This keypad is the same on all variants, supporting up to 96 different + keys. The linux-specific properties are modeled on those already existing + in other input drivers. + - compatible : must be "toshiba,tc3589x-keypad" + - debounce-delay-ms : debounce interval in milliseconds + - keypad,num-rows : number of rows in the matrix, see + bindings/input/matrix-keymap.txt + - keypad,num-columns : number of columns in the matrix, see + bindings/input/matrix-keymap.txt + - linux,keymap: the definition can be found in + bindings/input/matrix-keymap.txt + - linux,no-autorepeat: do no enable autorepeat feature. + - linux,wakeup: use any event on keypad as wakeup event. + +Example: + +tc35893@44 { + compatible = "toshiba,tc35893"; + reg = <0x44>; + interrupt-parent = <&gpio6>; + interrupts = <26 IRQ_TYPE_EDGE_RISING>; + + interrupt-controller; + #interrupt-cells = <1>; + + tc3589x_gpio { + compatible = "toshiba,tc3589x-gpio"; + interrupts = <0>; + + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + }; + tc3589x_keypad { + compatible = "toshiba,tc3589x-keypad"; + interrupts = <6>; + debounce-delay-ms = <4>; + keypad,num-columns = <8>; + keypad,num-rows = <8>; + linux,no-autorepeat; + linux,wakeup; + linux,keymap = <0x0301006b + 0x04010066 + 0x06040072 + 0x040200d7 + 0x0303006a + 0x0205000e + 0x0607008b + 0x0500001c + 0x0403000b + 0x03040034 + 0x05020067 + 0x0305006c + 0x040500e7 + 0x0005009e + 0x06020073 + 0x01030039 + 0x07060069 + 0x050500d9>; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/ti-keystone-devctrl.txt b/Documentation/devicetree/bindings/mfd/ti-keystone-devctrl.txt new file mode 100644 index 000000000000..20963c76b4bc --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/ti-keystone-devctrl.txt @@ -0,0 +1,19 @@ +* Device tree bindings for Texas Instruments keystone device state control + +The Keystone II devices have a set of registers that are used to control +the status of its peripherals. This node is intended to allow access to +this functionality. + +Required properties: + +- compatible: "ti,keystone-devctrl", "syscon" + +- reg: contains offset/length value for device state control + registers space. + +Example: + +devctrl: device-state-control@0x02620000 { + compatible = "ti,keystone-devctrl", "syscon"; + reg = <0x02620000 0x1000>; +}; diff --git a/Documentation/devicetree/bindings/mfd/tps65910.txt b/Documentation/devicetree/bindings/mfd/tps65910.txt index b4bd98af1cc7..38833e63a59f 100644 --- a/Documentation/devicetree/bindings/mfd/tps65910.txt +++ b/Documentation/devicetree/bindings/mfd/tps65910.txt @@ -11,7 +11,7 @@ Required properties: - #interrupt-cells: the number of cells to describe an IRQ, this should be 2. The first cell is the IRQ number. The second cell is the flags, encoded as the trigger masks from - Documentation/devicetree/bindings/interrupts.txt + Documentation/devicetree/bindings/interrupt-controller/interrupts.txt - regulators: This is the list of child nodes that specify the regulator initialization data for defined regulators. Not all regulators for the given device need to be present. The definition for each of these nodes is defined diff --git a/Documentation/devicetree/bindings/mfd/twl4030-power.txt b/Documentation/devicetree/bindings/mfd/twl4030-power.txt index 8e15ec35ac99..3d19963312ce 100644 --- a/Documentation/devicetree/bindings/mfd/twl4030-power.txt +++ b/Documentation/devicetree/bindings/mfd/twl4030-power.txt @@ -5,11 +5,31 @@ to control the power resources, including power scripts. For now, the binding only supports the complete shutdown of the system after poweroff. Required properties: -- compatible : must be "ti,twl4030-power" +- compatible : must be one of the following + "ti,twl4030-power" + "ti,twl4030-power-reset" + "ti,twl4030-power-idle" + "ti,twl4030-power-idle-osc-off" + +The use of ti,twl4030-power-reset is recommended at least on +3530 that needs a special configuration for warm reset to work. + +When using ti,twl4030-power-idle, the TI recommended configuration +for idle modes is loaded to the tlw4030 PMIC. + +When using ti,twl4030-power-idle-osc-off, the TI recommended +configuration is used with the external oscillator being shut +down during off-idle. Note that this does not work on all boards +depending on how the external oscillator is wired. Optional properties: -- ti,use_poweroff: With this flag, the chip will initiates an ACTIVE-to-OFF or - SLEEP-to-OFF transition when the system poweroffs. + +- ti,system-power-controller: This indicates that TWL4030 is the + power supply master of the system. With this flag, the chip will + initiate an ACTIVE-to-OFF or SLEEP-to-OFF transition when the + system poweroffs. + +- ti,use_poweroff: Deprecated name for ti,system-power-controller Example: &i2c1 { diff --git a/Documentation/devicetree/bindings/mfd/twl6040.txt b/Documentation/devicetree/bindings/mfd/twl6040.txt index 0f5dd709d752..a41157b5d930 100644 --- a/Documentation/devicetree/bindings/mfd/twl6040.txt +++ b/Documentation/devicetree/bindings/mfd/twl6040.txt @@ -19,6 +19,8 @@ Required properties: Optional properties, nodes: - enable-active-high: To power on the twl6040 during boot. +- clocks: phandle to the clk32k clock provider +- clock-names: Must be "clk32k" Vibra functionality Required properties: diff --git a/Documentation/devicetree/bindings/misc/allwinner,sunxi-sid.txt b/Documentation/devicetree/bindings/misc/allwinner,sunxi-sid.txt index 68ba37295565..fabdf64a5737 100644 --- a/Documentation/devicetree/bindings/misc/allwinner,sunxi-sid.txt +++ b/Documentation/devicetree/bindings/misc/allwinner,sunxi-sid.txt @@ -1,12 +1,12 @@ Allwinner sunxi-sid Required properties: -- compatible: "allwinner,sun4i-sid" or "allwinner,sun7i-a20-sid". +- compatible: "allwinner,sun4i-a10-sid" or "allwinner,sun7i-a20-sid" - reg: Should contain registers location and length Example for sun4i: sid@01c23800 { - compatible = "allwinner,sun4i-sid"; + compatible = "allwinner,sun4i-a10-sid"; reg = <0x01c23800 0x10> }; diff --git a/Documentation/devicetree/bindings/misc/arm-charlcd.txt b/Documentation/devicetree/bindings/misc/arm-charlcd.txt new file mode 100644 index 000000000000..e28e2aac47f1 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/arm-charlcd.txt @@ -0,0 +1,18 @@ +ARM Versatile Character LCD +----------------------------------------------------- +This binding defines the character LCD interface found on ARM Versatile AB +and PB reference platforms. + +Required properties: +- compatible : "arm,versatile-clcd" +- reg : Location and size of character LCD registers + +Optional properties: +- interrupts - single interrupt for character LCD. The character LCD can + operate in polled mode without an interrupt. + +Example: + lcd@10008000 { + compatible = "arm,versatile-lcd"; + reg = <0x10008000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/misc/atmel-ssc.txt b/Documentation/devicetree/bindings/misc/atmel-ssc.txt index 60960b2755f4..efc98ea1f23d 100644 --- a/Documentation/devicetree/bindings/misc/atmel-ssc.txt +++ b/Documentation/devicetree/bindings/misc/atmel-ssc.txt @@ -17,6 +17,14 @@ Required properties for devices compatible with "atmel,at91sam9g45-ssc": See Documentation/devicetree/bindings/dma/atmel-dma.txt for details. - dma-names: Must be "tx", "rx". +Optional properties: + - atmel,clk-from-rk-pin: bool property. + - When SSC works in slave mode, according to the hardware design, the + clock can get from TK pin, and also can get from RK pin. So, add + this parameter to choose where the clock from. + - By default the clock is from TK pin, if the clock from RK pin, this + property is needed. + Examples: - PDC transfer: ssc0: ssc@fffbc000 { diff --git a/Documentation/devicetree/bindings/misc/nvidia,tegra20-apbmisc.txt b/Documentation/devicetree/bindings/misc/nvidia,tegra20-apbmisc.txt new file mode 100644 index 000000000000..b97b8bef1fe5 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/nvidia,tegra20-apbmisc.txt @@ -0,0 +1,13 @@ +NVIDIA Tegra20/Tegra30/Tegr114/Tegra124 apbmisc block + +Required properties: +- compatible : should be: + "nvidia,tegra20-apbmisc" + "nvidia,tegra30-apbmisc" + "nvidia,tegra114-apbmisc" + "nvidia,tegra124-apbmisc" +- reg: Should contain 2 entries: the first entry gives the physical address + and length of the registers which contain revision and debug features. + The second entry gives the physical address and length of the + registers indicating the strapping options. + diff --git a/Documentation/devicetree/bindings/misc/sram.txt b/Documentation/devicetree/bindings/misc/sram.txt index 4d0a00e453a8..36cbe5aea990 100644 --- a/Documentation/devicetree/bindings/misc/sram.txt +++ b/Documentation/devicetree/bindings/misc/sram.txt @@ -8,9 +8,44 @@ Required properties: - reg : SRAM iomem address range +Reserving sram areas: +--------------------- + +Each child of the sram node specifies a region of reserved memory. Each +child node should use a 'reg' property to specify a specific range of +reserved memory. + +Following the generic-names recommended practice, node names should +reflect the purpose of the node. Unit address (@<address>) should be +appended to the name. + +Required properties in the sram node: + +- #address-cells, #size-cells : should use the same values as the root node +- ranges : standard definition, should translate from local addresses + within the sram to bus addresses + +Required properties in the area nodes: + +- reg : iomem address range, relative to the SRAM range + +Optional properties in the area nodes: + +- compatible : standard definition, should contain a vendor specific string + in the form <vendor>,[<device>-]<usage> + Example: sram: sram@5c000000 { compatible = "mmio-sram"; reg = <0x5c000000 0x40000>; /* 256 KiB SRAM at address 0x5c000000 */ + + #adress-cells = <1>; + #size-cells = <1>; + ranges = <0 0x5c000000 0x40000>; + + smp-sram@100 { + compatible = "socvendor,smp-sram"; + reg = <0x100 0x50>; + }; }; diff --git a/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt index 0a85c70cd30a..07ad02075a93 100644 --- a/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt +++ b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt @@ -13,6 +13,9 @@ Required properties: - #address-cells: should be one. The cell is the slot id. - #size-cells: should be zero. - at least one slot node +- clock-names: tuple listing input clock names. + Required elements: "mci_clk" +- clocks: phandles to input clocks. The node contains child nodes for each slot that the platform uses @@ -24,6 +27,8 @@ mmc0: mmc@f0008000 { interrupts = <12 4>; #address-cells = <1>; #size-cells = <0>; + clock-names = "mci_clk"; + clocks = <&mci0_clk>; [ child node definitions...] }; diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt index 532b1d440abc..ee4fc0576c7d 100644 --- a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt @@ -18,6 +18,10 @@ Required Properties: specific extensions. - "samsung,exynos5420-dw-mshc": for controllers with Samsung Exynos5420 specific extensions. + - "samsung,exynos7-dw-mshc": for controllers with Samsung Exynos7 + specific extensions. + - "samsung,exynos7-dw-mshc-smu": for controllers with Samsung Exynos7 + specific extensions having an SMU. * samsung,dw-mshc-ciu-div: Specifies the divider value for the card interface unit (ciu) clock. This property is applicable only for Exynos5 SoC's and @@ -46,13 +50,14 @@ Required Properties: - if CIU clock divider value is 0 (that is divide by 1), both tx and rx phase shift clocks should be 0. -Required properties for a slot: +Required properties for a slot (Deprecated - Recommend to use one slot per host): * gpios: specifies a list of gpios used for command, clock and data bus. The first gpio is the command line and the second gpio is the clock line. The rest of the gpios (depending on the bus-width property) are the data lines in no particular order. The format of the gpio specifier depends on the gpio controller. +(Deprecated - Refer to Documentation/devicetree/binding/pinctrl/samsung-pinctrl.txt) Example: @@ -69,21 +74,13 @@ Example: dwmmc0@12200000 { num-slots = <1>; - supports-highspeed; + cap-mmc-highspeed; + cap-sd-highspeed; broken-cd; fifo-depth = <0x80>; card-detect-delay = <200>; samsung,dw-mshc-ciu-div = <3>; samsung,dw-mshc-sdr-timing = <2 3>; samsung,dw-mshc-ddr-timing = <1 2>; - - slot@0 { - reg = <0>; - bus-width = <8>; - gpios = <&gpc0 0 2 0 3>, <&gpc0 1 2 0 3>, - <&gpc1 0 2 3 3>, <&gpc1 1 2 3 3>, - <&gpc1 2 2 3 3>, <&gpc1 3 2 3 3>, - <&gpc0 3 2 3 3>, <&gpc0 4 2 3 3>, - <&gpc0 5 2 3 3>, <&gpc0 6 2 3 3>; - }; + bus-width = <8>; }; diff --git a/Documentation/devicetree/bindings/mmc/img-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/img-dw-mshc.txt new file mode 100644 index 000000000000..85de99fcaa2f --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/img-dw-mshc.txt @@ -0,0 +1,29 @@ +* Imagination specific extensions to the Synopsys Designware Mobile Storage + Host Controller + +The Synopsys designware mobile storage host controller is used to interface +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents +differences between the core Synopsys dw mshc controller properties described +by synopsys-dw-mshc.txt and the properties used by the Imagination specific +extensions to the Synopsys Designware Mobile Storage Host Controller. + +Required Properties: + +* compatible: should be + - "img,pistachio-dw-mshc": for Pistachio SoCs + +Example: + + mmc@18142000 { + compatible = "img,pistachio-dw-mshc"; + reg = <0x18142000 0x400>; + interrupts = <GIC_SHARED 39 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&system_clk>, <&sdhost_clk>; + clock-names = "biu", "ciu"; + + fifo-depth = <0x20>; + bus-width = <4>; + num-slots = <1>; + disable-wp; + }; diff --git a/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt index b8653ea97957..3b3544931437 100644 --- a/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt @@ -12,7 +12,7 @@ extensions to the Synopsys Designware Mobile Storage Host Controller. Required Properties: * compatible: should be one of the following. - - "hisilicon,hi4511-dw-mshc": for controllers with hi4511 specific extentions. + - "hisilicon,hi4511-dw-mshc": for controllers with hi4511 specific extensions. Example: @@ -34,13 +34,11 @@ Example: num-slots = <1>; vmmc-supply = <&ldo12>; fifo-depth = <0x100>; - supports-highspeed; pinctrl-names = "default"; pinctrl-0 = <&sd_pmx_pins &sd_cfg_func1 &sd_cfg_func2>; - slot@0 { - reg = <0>; - bus-width = <4>; - disable-wp; - cd-gpios = <&gpio10 3 0>; - }; + bus-width = <4>; + disable-wp; + cd-gpios = <&gpio10 3 0>; + cap-mmc-highspeed; + cap-sd-highspeed; }; diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 458b57f199af..b52628b18a53 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -26,9 +26,22 @@ Optional properties: this system, even if the controller claims it is. - cap-sd-highspeed: SD high-speed timing is supported - cap-mmc-highspeed: MMC high-speed timing is supported +- sd-uhs-sdr12: SD UHS SDR12 speed is supported +- sd-uhs-sdr25: SD UHS SDR25 speed is supported +- sd-uhs-sdr50: SD UHS SDR50 speed is supported +- sd-uhs-sdr104: SD UHS SDR104 speed is supported +- sd-uhs-ddr50: SD UHS DDR50 speed is supported - cap-power-off-card: powering off the card is safe - cap-sdio-irq: enable SDIO IRQ signalling on this interface - full-pwr-cycle: full power cycle of the card is supported +- mmc-ddr-1_8v: eMMC high-speed DDR mode(1.8V I/O) is supported +- mmc-ddr-1_2v: eMMC high-speed DDR mode(1.2V I/O) is supported +- mmc-hs200-1_8v: eMMC HS200 mode(1.8V I/O) is supported +- mmc-hs200-1_2v: eMMC HS200 mode(1.2V I/O) is supported +- mmc-hs400-1_8v: eMMC HS400 mode(1.8V I/O) is supported +- mmc-hs400-1_2v: eMMC HS400 mode(1.2V I/O) is supported +- dsr: Value the card's (optional) Driver Stage Register (DSR) should be + programmed with. Valid range: [0 .. 0xffff]. *NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line polarity properties, we have to fix the meaning of the "normal" and "inverted" diff --git a/Documentation/devicetree/bindings/mmc/mmci.txt b/Documentation/devicetree/bindings/mmc/mmci.txt index 2b584cae352a..03796cf2d3e7 100644 --- a/Documentation/devicetree/bindings/mmc/mmci.txt +++ b/Documentation/devicetree/bindings/mmc/mmci.txt @@ -4,12 +4,58 @@ The ARM PrimeCell MMCI PL180 and PL181 provides an interface for reading and writing to MultiMedia and SD cards alike. This file documents differences between the core properties described -by mmc.txt and the properties used by the mmci driver. +by mmc.txt and the properties used by the mmci driver. Using "st" as +the prefix for a property, indicates support by the ST Micro variant. Required properties: - compatible : contains "arm,pl18x", "arm,primecell". -- arm,primecell-periphid : contains the PrimeCell Peripheral ID. +- vmmc-supply : phandle to the regulator device tree node, mentioned + as the VCC/VDD supply in the eMMC/SD specs. Optional properties: -- mmc-cap-mmc-highspeed : indicates whether MMC is high speed capable -- mmc-cap-sd-highspeed : indicates whether SD is high speed capable +- arm,primecell-periphid : contains the PrimeCell Peripheral ID, it overrides + the ID provided by the HW +- vqmmc-supply : phandle to the regulator device tree node, mentioned + as the VCCQ/VDD_IO supply in the eMMC/SD specs. +- st,sig-dir-dat0 : bus signal direction pin used for DAT[0]. +- st,sig-dir-dat2 : bus signal direction pin used for DAT[2]. +- st,sig-dir-dat31 : bus signal direction pin used for DAT[3] and DAT[1]. +- st,sig-dir-dat74 : bus signal direction pin used for DAT[4] to DAT[7]. +- st,sig-dir-cmd : cmd signal direction pin used for CMD. +- st,sig-pin-fbclk : feedback clock signal pin used. + +Deprecated properties: +- mmc-cap-mmc-highspeed : indicates whether MMC is high speed capable. +- mmc-cap-sd-highspeed : indicates whether SD is high speed capable. + +Example: + +sdi0_per1@80126000 { + compatible = "arm,pl18x", "arm,primecell"; + reg = <0x80126000 0x1000>; + interrupts = <0 60 IRQ_TYPE_LEVEL_HIGH>; + + dmas = <&dma 29 0 0x2>, /* Logical - DevToMem */ + <&dma 29 0 0x0>; /* Logical - MemToDev */ + dma-names = "rx", "tx"; + + clocks = <&prcc_kclk 1 5>, <&prcc_pclk 1 5>; + clock-names = "sdi", "apb_pclk"; + + max-frequency = <100000000>; + bus-width = <4>; + cap-sd-highspeed; + cap-mmc-highspeed; + cd-gpios = <&gpio2 31 0x4>; // 95 + st,sig-dir-dat0; + st,sig-dir-dat2; + st,sig-dir-cmd; + st,sig-pin-fbclk; + + vmmc-supply = <&ab8500_ldo_aux3_reg>; + vqmmc-supply = <&vmmci>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdi0_default_mode>; + pinctrl-1 = <&sdi0_sleep_mode>; +}; diff --git a/Documentation/devicetree/bindings/mmc/moxa,moxart-mmc.txt b/Documentation/devicetree/bindings/mmc/moxa,moxart-mmc.txt new file mode 100644 index 000000000000..b63819149f22 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/moxa,moxart-mmc.txt @@ -0,0 +1,30 @@ +MOXA ART MMC Host Controller Interface + + Inherits from mmc binding[1]. + + [1] Documentation/devicetree/bindings/mmc/mmc.txt + +Required properties: + +- compatible : Must be "moxa,moxart-mmc" or "faraday,ftsdc010" +- reg : Should contain registers location and length +- interrupts : Should contain the interrupt number +- clocks : Should contain phandle for the clock feeding the MMC controller + +Optional properties: + +- dmas : Should contain two DMA channels, line request number must be 5 for + both channels +- dma-names : Must be "tx", "rx" + +Example: + + mmc: mmc@98e00000 { + compatible = "moxa,moxart-mmc"; + reg = <0x98e00000 0x5C>; + interrupts = <5 0>; + clocks = <&clk_apb>; + dmas = <&dma 5>, + <&dma 5>; + dma-names = "tx", "rx"; + }; diff --git a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt new file mode 100644 index 000000000000..299081f94abd --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt @@ -0,0 +1,32 @@ +* Renesas Multi Media Card Interface (MMCIF) Controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the MMCIF device. + + +Required properties: + +- compatible: must contain one of the following + - "renesas,mmcif-r8a7740" for the MMCIF found in r8a7740 SoCs + - "renesas,mmcif-r8a7790" for the MMCIF found in r8a7790 SoCs + - "renesas,mmcif-r8a7791" for the MMCIF found in r8a7791 SoCs + - "renesas,sh-mmcif" for the generic MMCIF + +- clocks: reference to the functional clock + +- dmas: reference to the DMA channels, one per channel name listed in the + dma-names property. +- dma-names: must contain "tx" for the transmit DMA channel and "rx" for the + receive DMA channel. + + +Example: R8A7790 (R-Car H2) MMCIF0 + + mmcif0: mmc@ee200000 { + compatible = "renesas,mmcif-r8a7790", "renesas,sh-mmcif"; + reg = <0 0xee200000 0 0x80>; + interrupts = <0 169 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A7790_CLK_MMCIF0>; + dmas = <&dmac0 0xd1>, <&dmac0 0xd2>; + dma-names = "tx", "rx"; + }; diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt index c559f3f36309..c327c2d6f23d 100644 --- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt @@ -10,12 +10,14 @@ extensions to the Synopsys Designware Mobile Storage Host Controller. Required Properties: * compatible: should be - - "rockchip,rk2928-dw-mshc": for Rockchip RK2928 and following + - "rockchip,rk2928-dw-mshc": for Rockchip RK2928 and following, + before RK3288 + - "rockchip,rk3288-dw-mshc": for Rockchip RK3288 Example: rkdwmmc0@12200000 { - compatible = "rockchip,rk2928-dw-mshc"; + compatible = "rockchip,rk3288-dw-mshc"; reg = <0x12200000 0x1000>; interrupts = <0 75 0>; #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt index 328e990d2546..42e0a9afa100 100644 --- a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt @@ -3,7 +3,7 @@ Samsung's SDHCI controller is used as a connectivity interface with external MMC, SD and eMMC storage mediums. This file documents differences between the core mmc properties described by mmc.txt and the properties used by the -Samsung implmentation of the SDHCI controller. +Samsung implementation of the SDHCI controller. Required SoC Specific Properties: - compatible: should be one of the following diff --git a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt new file mode 100644 index 000000000000..485483a63d8c --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt @@ -0,0 +1,55 @@ +* Qualcomm SDHCI controller (sdhci-msm) + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-msm driver. + +Required properties: +- compatible: Should contain "qcom,sdhci-msm-v4". +- reg: Base address and length of the register in the following order: + - Host controller register map (required) + - SD Core register map (required) +- interrupts: Should contain an interrupt-specifiers for the interrupts: + - Host controller interrupt (required) +- pinctrl-names: Should contain only one value - "default". +- pinctrl-0: Should specify pin control groups used for this controller. +- clocks: A list of phandle + clock-specifier pairs for the clocks listed in clock-names. +- clock-names: Should contain the following: + "iface" - Main peripheral bus clock (PCLK/HCLK - AHB Bus clock) (required) + "core" - SDC MMC clock (MCLK) (required) + "bus" - SDCC bus voter clock (optional) + +Example: + + sdhc_1: sdhci@f9824900 { + compatible = "qcom,sdhci-msm-v4"; + reg = <0xf9824900 0x11c>, <0xf9824000 0x800>; + interrupts = <0 123 0>; + bus-width = <8>; + non-removable; + + vmmc-supply = <&pm8941_l20>; + vqmmc-supply = <&pm8941_s3>; + + pinctrl-names = "default"; + pinctrl-0 = <&sdc1_clk &sdc1_cmd &sdc1_data>; + + clocks = <&gcc GCC_SDCC1_APPS_CLK>, <&gcc GCC_SDCC1_AHB_CLK>; + clock-names = "core", "iface"; + }; + + sdhc_2: sdhci@f98a4900 { + compatible = "qcom,sdhci-msm-v4"; + reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>; + interrupts = <0 125 0>; + bus-width = <4>; + cd-gpios = <&msmgpio 62 0x1>; + + vmmc-supply = <&pm8941_l21>; + vqmmc-supply = <&pm8941_l13>; + + pinctrl-names = "default"; + pinctrl-0 = <&sdc2_clk &sdc2_cmd &sdc2_data>; + + clocks = <&gcc GCC_SDCC2_APPS_CLK>, <&gcc GCC_SDCC2_AHB_CLK>; + clock-names = "core", "iface"; + }; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt b/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt index dbe98a3c183a..4dd6deb90719 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt @@ -4,7 +4,18 @@ This file documents differences between the core properties in mmc.txt and the properties used by the sdhci-pxav2 and sdhci-pxav3 drivers. Required properties: -- compatible: Should be "mrvl,pxav2-mmc" or "mrvl,pxav3-mmc". +- compatible: Should be "mrvl,pxav2-mmc", "mrvl,pxav3-mmc" or + "marvell,armada-380-sdhci". +- reg: + * for "mrvl,pxav2-mmc" and "mrvl,pxav3-mmc", one register area for + the SDHCI registers. + * for "marvell,armada-380-sdhci", two register areas. The first one + for the SDHCI registers themselves, and the second one for the + AXI/Mbus bridge registers of the SDHCI unit. +- clocks: Array of clocks required for SDHCI; requires at least one for + I/O clock. +- clock-names: Array of names corresponding to clocks property; shall be + "io" for I/O clock and "core" for optional core clock. Optional properties: - mrvl,clk-delay-cycles: Specify a number of cycles to delay for tuning. @@ -16,6 +27,17 @@ sdhci@d4280800 { reg = <0xd4280800 0x800>; bus-width = <8>; interrupts = <27>; + clocks = <&chip CLKID_SDIO1XIN>, <&chip CLKID_SDIO1>; + clock-names = "io", "core"; non-removable; mrvl,clk-delay-cycles = <31>; }; + +sdhci@d8000 { + compatible = "marvell,armada-380-sdhci"; + reg = <0xd8000 0x1000>, <0xdc000 0x100>; + interrupts = <0 25 0x4>; + clocks = <&gateclk 17>; + clock-names = "io"; + mrvl,clk-delay-cycles = <0x1F>; +}; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-st.txt b/Documentation/devicetree/bindings/mmc/sdhci-st.txt new file mode 100644 index 000000000000..7527db447a35 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-st.txt @@ -0,0 +1,33 @@ +* STMicroelectronics sdhci-st MMC/SD controller + +This file documents the differences between the core properties in +Documentation/devicetree/bindings/mmc/mmc.txt and the properties +used by the sdhci-st driver. + +Required properties: +- compatible : Must be "st,sdhci" +- clock-names : Should be "mmc" + See: Documentation/devicetree/bindings/resource-names.txt +- clocks : Phandle of the clock used by the sdhci controler + See: Documentation/devicetree/bindings/clock/clock-bindings.txt + +Optional properties: +- non-removable: non-removable slot + See: Documentation/devicetree/bindings/mmc/mmc.txt +- bus-width: Number of data lines + See: Documentation/devicetree/bindings/mmc/mmc.txt + +Example: + +mmc0: sdhci@fe81e000 { + compatible = "st,sdhci"; + status = "disabled"; + reg = <0xfe81e000 0x1000>; + interrupts = <GIC_SPI 127 IRQ_TYPE_NONE>; + interrupt-names = "mmcirq"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mmc0>; + clock-names = "mmc"; + clocks = <&clk_s_a1_ls 1>; + bus-width = <8> +}; diff --git a/Documentation/devicetree/bindings/mmc/socfpga-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/socfpga-dw-mshc.txt new file mode 100644 index 000000000000..4897bea7e3f8 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/socfpga-dw-mshc.txt @@ -0,0 +1,23 @@ +* Altera SOCFPGA specific extensions to the Synopsys Designware Mobile + Storage Host Controller + +The Synopsys designware mobile storage host controller is used to interface +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents +differences between the core Synopsys dw mshc controller properties described +by synopsys-dw-mshc.txt and the properties used by the Altera SOCFPGA specific +extensions to the Synopsys Designware Mobile Storage Host Controller. + +Required Properties: + +* compatible: should be + - "altr,socfpga-dw-mshc": for Altera's SOCFPGA platform + +Example: + + mmc: dwmmc0@ff704000 { + compatible = "altr,socfpga-dw-mshc"; + reg = <0xff704000 0x1000>; + interrupts = <0 129 4>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt new file mode 100644 index 000000000000..91b3a3467150 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt @@ -0,0 +1,43 @@ +* Allwinner sunxi MMC controller + +The highspeed MMC host controller on Allwinner SoCs provides an interface +for MMC, SD and SDIO types of memory cards. + +Supported maximum speeds are the ones of the eMMC standard 4.5 as well +as the speed of SD standard 3.0. +Absolute maximum transfer rate is 200MB/s + +Required properties: + - compatible : "allwinner,sun4i-a10-mmc" or "allwinner,sun5i-a13-mmc" + - reg : mmc controller base registers + - clocks : a list with 2 phandle + clock specifier pairs + - clock-names : must contain "ahb" and "mmc" + - interrupts : mmc controller interrupt + +Optional properties: + - resets : phandle + reset specifier pair + - reset-names : must contain "ahb" + - for cd, bus-width and additional generic mmc parameters + please refer to mmc.txt within this directory + +Examples: + - Within .dtsi: + mmc0: mmc@01c0f000 { + compatible = "allwinner,sun5i-a13-mmc"; + reg = <0x01c0f000 0x1000>; + clocks = <&ahb_gates 8>, <&mmc0_clk>; + clock-names = "ahb", "mod"; + interrupts = <0 32 4>; + status = "disabled"; + }; + + - Within dts: + mmc0: mmc@01c0f000 { + pinctrl-names = "default", "default"; + pinctrl-0 = <&mmc0_pins_a>; + pinctrl-1 = <&mmc0_cd_pin_reference_design>; + bus-width = <4>; + cd-gpios = <&pio 7 1 0>; /* PH1 */ + cd-inverted; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt index 8f3f13315358..346c6095a615 100644 --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt @@ -67,11 +67,8 @@ Optional properties: * card-detect-delay: Delay in milli-seconds before detecting card after card insert event. The default value is 0. -* supports-highspeed: Enables support for high speed cards (up to 50MHz) - -* caps2-mmc-hs200-1_8v: Supports mmc HS200 SDR 1.8V mode - -* caps2-mmc-hs200-1_2v: Supports mmc HS200 SDR 1.2V mode +* supports-highspeed (DEPRECATED): Enables support for high speed cards (up to 50MHz) + (use "cap-mmc-highspeed" or "cap-sd-highspeed" instead) * broken-cd: as documented in mmc core bindings. @@ -102,15 +99,11 @@ board specific portions as listed below. clock-frequency = <400000000>; clock-freq-min-max = <400000 200000000>; num-slots = <1>; - supports-highspeed; - caps2-mmc-hs200-1_8v; broken-cd; fifo-depth = <0x80>; card-detect-delay = <200>; vmmc-supply = <&buck8>; - - slot@0 { - reg = <0>; - bus-width = <8>; - }; + bus-width = <8>; + cap-mmc-highspeed; + cap-sd-highspeed; }; diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt index 8c8908ab84ba..76bf087bc889 100644 --- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt @@ -10,7 +10,9 @@ Required properties: - compatible: Should be "ti,omap2-hsmmc", for OMAP2 controllers Should be "ti,omap3-hsmmc", for OMAP3 controllers + Should be "ti,omap3-pre-es3-hsmmc" for OMAP3 controllers pre ES3.0 Should be "ti,omap4-hsmmc", for OMAP4 controllers + Should be "ti,am33xx-hsmmc", for AM335x controllers - ti,hwmods: Must be "mmc<n>", n is controller instance starting 1 Optional properties: @@ -55,3 +57,56 @@ Examples: &edma 25>; dma-names = "tx", "rx"; }; + +[workaround for missing swakeup on am33xx] + +This SOC is missing the swakeup line, it will not detect SDIO irq +while in suspend. + + ------ + | PRCM | + ------ + ^ | + swakeup | | fclk + | v + ------ ------- ----- + | card | -- CIRQ --> | hsmmc | -- IRQ --> | CPU | + ------ ------- ----- + +In suspend the fclk is off and the module is disfunctional. Even register reads +will fail. A small logic in the host will request fclk restore, when an +external event is detected. Once the clock is restored, the host detects the +event normally. Since am33xx doesn't have this line it never wakes from +suspend. + +The workaround is to reconfigure the dat1 line as a GPIO upon suspend. To make +this work, we need to set the named pinctrl states "default" and "idle". +Prepare idle to remux dat1 as a gpio, and default to remux it back as sdio +dat1. The MMC driver will then toggle between idle and default state during +runtime. + +In summary: +1. select matching 'compatible' section, see example below. +2. specify pinctrl states "default" and "idle", "sleep" is optional. +3. specify the gpio irq used for detecting sdio irq in suspend + +If configuration is incomplete, a warning message is emitted "falling back to +polling". Also check the "sdio irq mode" in /sys/kernel/debug/mmc0/regs. Mind +not every application needs SDIO irq, e.g. MMC cards. + + mmc1: mmc@48060100 { + compatible = "ti,am33xx-hsmmc"; + ... + pinctrl-names = "default", "idle", "sleep" + pinctrl-0 = <&mmc1_pins>; + pinctrl-1 = <&mmc1_idle>; + pinctrl-2 = <&mmc1_sleep>; + ... + interrupts-extended = <&intc 64 &gpio2 28 0>; + }; + + mmc1_idle : pinmux_cirq_pin { + pinctrl-single,pins = < + 0x0f8 0x3f /* GPIO2_28 */ + >; + }; diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index 6a2a1160a70d..400b640fabc7 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -18,6 +18,10 @@ Required properties: "renesas,sdhi-r8a7778" - SDHI IP on R8A7778 SoC "renesas,sdhi-r8a7779" - SDHI IP on R8A7779 SoC "renesas,sdhi-r8a7790" - SDHI IP on R8A7790 SoC + "renesas,sdhi-r8a7791" - SDHI IP on R8A7791 SoC + "renesas,sdhi-r8a7792" - SDHI IP on R8A7792 SoC + "renesas,sdhi-r8a7793" - SDHI IP on R8A7793 SoC + "renesas,sdhi-r8a7794" - SDHI IP on R8A7794 SoC Optional properties: - toshiba,mmc-wrprotect-disable: write-protect detection is unavailable diff --git a/Documentation/devicetree/bindings/mmc/usdhi6rol0.txt b/Documentation/devicetree/bindings/mmc/usdhi6rol0.txt new file mode 100644 index 000000000000..8babdaa8623b --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/usdhi6rol0.txt @@ -0,0 +1,33 @@ +* Renesas usdhi6rol0 SD/SDIO host controller + +Required properties: + +- compatible: must be + "renesas,usdhi6rol0" +- interrupts: 3 interrupts, named "card detect", "data" and "SDIO" must be + specified +- clocks: a clock binding for the IMCLK input + +Optional properties: + +- vmmc-supply: a phandle of a regulator, supplying Vcc to the card +- vqmmc-supply: a phandle of a regulator, supplying VccQ to the card + +Additionally any standard mmc bindings from mmc.txt can be used. + +Example: + +sd0: sd@ab000000 { + compatible = "renesas,usdhi6rol0"; + reg = <0xab000000 0x200>; + interrupts = <0 23 0x4 + 0 24 0x4 + 0 25 0x4>; + interrupt-names = "card detect", "data", "SDIO"; + bus-width = <4>; + max-frequency = <50000000>; + cap-power-off-card; + clocks = <&imclk>; + vmmc-supply = <&vcc_sd0>; + vqmmc-supply = <&vccq_sd0>; +}; diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt index c4728839d0c1..6edc3b616e98 100644 --- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt @@ -36,6 +36,7 @@ Optional properties: - reg : should specify the address and size used for NFC command registers, NFC registers and NFC Sram. NFC Sram address and size can be absent if don't want to use it. + - clocks: phandle to the peripheral clock - Optional properties: - atmel,write-by-sram: boolean to enable NFC write by sram. @@ -98,6 +99,7 @@ nand0: nand@40000000 { compatible = "atmel,sama5d3-nfc"; #address-cells = <1>; #size-cells = <1>; + clocks = <&hsmc_clk> reg = < 0x70000000 0x10000000 /* NFC Command Registers */ 0xffffc000 0x00000070 /* NFC HSMC regs */ diff --git a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt new file mode 100644 index 000000000000..823d13412195 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt @@ -0,0 +1,35 @@ +* Freescale Quad Serial Peripheral Interface(QuadSPI) + +Required properties: + - compatible : Should be "fsl,vf610-qspi" + - reg : the first contains the register location and length, + the second contains the memory mapping address and length + - reg-names: Should contain the reg names "QuadSPI" and "QuadSPI-memory" + - interrupts : Should contain the interrupt for the device + - clocks : The clocks needed by the QuadSPI controller + - clock-names : the name of the clocks + +Optional properties: + - fsl,qspi-has-second-chip: The controller has two buses, bus A and bus B. + Each bus can be connected with two NOR flashes. + Most of the time, each bus only has one NOR flash + connected, this is the default case. + But if there are two NOR flashes connected to the + bus, you should enable this property. + (Please check the board's schematic.) + +Example: + +qspi0: quadspi@40044000 { + compatible = "fsl,vf610-qspi"; + reg = <0x40044000 0x1000>, <0x20000000 0x10000000>; + reg-names = "QuadSPI", "QuadSPI-memory"; + interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks VF610_CLK_QSPI0_EN>, + <&clks VF610_CLK_QSPI0>; + clock-names = "qspi_en", "qspi"; + + flash0: s25fl128s@0 { + .... + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt index 5e1f31b5ff70..fb733c4e1c11 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt @@ -22,12 +22,14 @@ Optional properties: width of 8 is assumed. - ti,nand-ecc-opt: A string setting the ECC layout to use. One of: - "sw" <deprecated> use "ham1" instead + "sw" 1-bit Hamming ecc code via software "hw" <deprecated> use "ham1" instead "hw-romcode" <deprecated> use "ham1" instead "ham1" 1-bit Hamming ecc code "bch4" 4-bit BCH ecc code "bch8" 8-bit BCH ecc code + "bch16" 16-bit BCH ECC code + Refer below "How to select correct ECC scheme for your device ?" - ti,nand-xfer-type: A string setting the data transfer type. One of: @@ -43,7 +45,7 @@ Optional properties: ELM hardware engines should specify this device node in .dtsi Using ELM for ECC error correction frees some CPU cycles. -For inline partiton table parsing (optional): +For inline partition table parsing (optional): - #address-cells: should be set to 1 - #size-cells: should be set to 1 @@ -90,3 +92,46 @@ Example for an AM33xx board: }; }; +How to select correct ECC scheme for your device ? +-------------------------------------------------- +Higher ECC scheme usually means better protection against bit-flips and +increased system lifetime. However, selection of ECC scheme is dependent +on various other factors also like; + +(1) support of built in hardware engines. + Some legacy OMAP SoC do not have ELM harware engine, so those SoC cannot + support ecc-schemes with hardware error-correction (BCHx_HW). However + such SoC can use ecc-schemes with software library for error-correction + (BCHx_HW_DETECTION_SW). The error correction capability with software + library remains equivalent to their hardware counter-part, but there is + slight CPU penalty when too many bit-flips are detected during reads. + +(2) Device parameters like OOBSIZE. + Other factor which governs the selection of ecc-scheme is oob-size. + Higher ECC schemes require more OOB/Spare area to store ECC syndrome, + so the device should have enough free bytes available its OOB/Spare + area to accommodate ECC for entire page. In general following expression + helps in determining if given device can accommodate ECC syndrome: + "2 + (PAGESIZE / 512) * ECC_BYTES" >= OOBSIZE" + where + OOBSIZE number of bytes in OOB/spare area + PAGESIZE number of bytes in main-area of device page + ECC_BYTES number of ECC bytes generated to protect + 512 bytes of data, which is: + '3' for HAM1_xx ecc schemes + '7' for BCH4_xx ecc schemes + '14' for BCH8_xx ecc schemes + '26' for BCH16_xx ecc schemes + + Example(a): For a device with PAGESIZE = 2048 and OOBSIZE = 64 and + trying to use BCH16 (ECC_BYTES=26) ecc-scheme. + Number of ECC bytes per page = (2 + (2048 / 512) * 26) = 106 B + which is greater than capacity of NAND device (OOBSIZE=64) + Hence, BCH16 cannot be supported on given device. But it can + probably use lower ecc-schemes like BCH8. + + Example(b): For a device with PAGESIZE = 2048 and OOBSIZE = 128 and + trying to use BCH16 (ECC_BYTES=26) ecc-scheme. + Number of ECC bytes per page = (2 + (2048 / 512) * 26) = 106 B + which can be accommodated in the OOB/Spare area of this device + (OOBSIZE=128). So this device can use BCH16 ecc-scheme. diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nor.txt b/Documentation/devicetree/bindings/mtd/gpmc-nor.txt index 420b3ab18890..4828c17bb784 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-nor.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-nor.txt @@ -30,7 +30,7 @@ Optional properties: - gpmc,XXX Additional GPMC timings and settings parameters. See Documentation/devicetree/bindings/bus/ti-gpmc.txt -Optional properties for partiton table parsing: +Optional properties for partition table parsing: - #address-cells: should be set to 1 - #size-cells: should be set to 1 diff --git a/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt index b7529424ac88..5d8fa527c496 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt @@ -17,7 +17,7 @@ Optional properties: - dma-channel: DMA Channel index -For inline partiton table parsing (optional): +For inline partition table parsing (optional): - #address-cells: should be set to 1 - #size-cells: should be set to 1 diff --git a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt index 458d59634688..a011fdf61dbf 100644 --- a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt @@ -25,6 +25,16 @@ Optional properties: discoverable or this property is not enabled, the software may chooses an implementation-defined ECC scheme. + - fsl,no-blockmark-swap: Don't swap the bad block marker from the OOB + area with the byte in the data area but rely on the + flash based BBT for identifying bad blocks. + NOTE: this is only valid in conjunction with + 'nand-on-flash-bbt'. + WARNING: on i.MX28 blockmark swapping cannot be + disabled for the BootROM in the FCB. Thus, + partitions written from Linux with this feature + turned on may not be accessible by the BootROM + code. The device tree may optionally contain sub-nodes describing partitions of the address space. See partition.txt for more detail. diff --git a/Documentation/devicetree/bindings/mtd/m25p80.txt b/Documentation/devicetree/bindings/mtd/m25p80.txt index 6d3d57609470..4611aa83531b 100644 --- a/Documentation/devicetree/bindings/mtd/m25p80.txt +++ b/Documentation/devicetree/bindings/mtd/m25p80.txt @@ -5,8 +5,8 @@ Required properties: representing partitions. - compatible : Should be the manufacturer and the name of the chip. Bear in mind the DT binding is not Linux-only, but in case of Linux, see the - "m25p_ids" table in drivers/mtd/devices/m25p80.c for the list of - supported chips. + "spi_nor_ids" table in drivers/mtd/spi-nor/spi-nor.c for the list + of supported chips. - reg : Chip-Select number - spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt index 61c5ec850f2f..6b9f680cb579 100644 --- a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt +++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt @@ -4,8 +4,8 @@ Flash chips (Memory Technology Devices) are often used for solid state file systems on embedded devices. - compatible : should contain the specific model of mtd chip(s) - used, if known, followed by either "cfi-flash", "jedec-flash" - or "mtd-ram". + used, if known, followed by either "cfi-flash", "jedec-flash", + "mtd-ram" or "mtd-rom". - reg : Address range(s) of the mtd chip(s) It's possible to (optionally) define multiple "reg" tuples so that non-identical chips can be described in one node. diff --git a/Documentation/devicetree/bindings/mtd/nand.txt b/Documentation/devicetree/bindings/mtd/nand.txt index 03855c8c492a..b53f92e252d4 100644 --- a/Documentation/devicetree/bindings/mtd/nand.txt +++ b/Documentation/devicetree/bindings/mtd/nand.txt @@ -5,3 +5,17 @@ "soft_bch". - nand-bus-width : 8 or 16 bus width if not present 8 - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false + +- nand-ecc-strength: integer representing the number of bits to correct + per ECC step. + +- nand-ecc-step-size: integer representing the number of data bytes + that are covered by a single ECC step. + +The ECC strength and ECC step size properties define the correction capability +of a controller. Together, they say a controller can correct "{strength} bit +errors per {size} bytes". + +The interpretation of these parameters is implementation-defined, so not all +implementations must support all possible combinations. However, implementations +are encouraged to further specify the value(s) they support. diff --git a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt index 86e0a5601ff5..de8b517a5521 100644 --- a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt +++ b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt @@ -17,6 +17,14 @@ Optional properties: - num-cs: Number of chipselect lines to usw - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false + - nand-ecc-strength: number of bits to correct per ECC step + - nand-ecc-step-size: number of data bytes covered by a single ECC step + +The following ECC strength and step size are currently supported: + + - nand-ecc-strength = <1>, nand-ecc-step-size = <512> + - nand-ecc-strength = <4>, nand-ecc-step-size = <512> + - nand-ecc-strength = <8>, nand-ecc-step-size = <512> Example: diff --git a/Documentation/devicetree/bindings/mtd/st-fsm.txt b/Documentation/devicetree/bindings/mtd/st-fsm.txt new file mode 100644 index 000000000000..c2489391c437 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/st-fsm.txt @@ -0,0 +1,26 @@ +* ST-Microelectronics SPI FSM Serial (NOR) Flash Controller + +Required properties: + - compatible : Should be "st,spi-fsm" + - reg : Contains register's location and length. + - reg-names : Should contain the reg names "spi-fsm" + - interrupts : The interrupt number + - pinctrl-0 : Standard Pinctrl phandle (see: pinctrl/pinctrl-bindings.txt) + +Optional properties: + - st,syscfg : Phandle to boot-device system configuration registers + - st,boot-device-reg : Address of the aforementioned boot-device register(s) + - st,boot-device-spi : Expected boot-device value if booted via this device + +Example: + spifsm: spifsm@fe902000{ + compatible = "st,spi-fsm"; + reg = <0xfe902000 0x1000>; + reg-names = "spi-fsm"; + pinctrl-0 = <&pinctrl_fsm>; + st,syscfg = <&syscfg_rear>; + st,boot-device-reg = <0x958>; + st,boot-device-spi = <0x1a>; + status = "okay"; + }; + diff --git a/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt b/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt index b90bfcd138ff..10640b17c866 100644 --- a/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt +++ b/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt @@ -1,20 +1,17 @@ * Allwinner EMAC ethernet controller Required properties: -- compatible: should be "allwinner,sun4i-emac". +- compatible: should be "allwinner,sun4i-a10-emac" (Deprecated: + "allwinner,sun4i-emac") - reg: address and length of the register set for the device. - interrupts: interrupt for the device -- phy: A phandle to a phy node defining the PHY address (as the reg - property, a single integer). +- phy: see ethernet.txt file in the same directory. - clocks: A phandle to the reference clock for this device -Optional properties: -- (local-)mac-address: mac address to be used by this driver - Example: emac: ethernet@01c0b000 { - compatible = "allwinner,sun4i-emac"; + compatible = "allwinner,sun4i-a10-emac"; reg = <0x01c0b000 0x1000>; interrupts = <55>; clocks = <&ahb_gates 17>; diff --git a/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt b/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt index 00b9f9a3ec1d..4ec56413779d 100644 --- a/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt +++ b/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt @@ -1,7 +1,8 @@ * Allwinner A10 MDIO Ethernet Controller interface Required properties: -- compatible: should be "allwinner,sun4i-mdio". +- compatible: should be "allwinner,sun4i-a10-mdio" + (Deprecated: "allwinner,sun4i-mdio"). - reg: address and length of the register set for the device. Optional properties: @@ -9,7 +10,7 @@ Optional properties: Example at the SoC level: mdio@01c0b080 { - compatible = "allwinner,sun4i-mdio"; + compatible = "allwinner,sun4i-a10-mdio"; reg = <0x01c0b080 0x14>; #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/net/altera_tse.txt b/Documentation/devicetree/bindings/net/altera_tse.txt new file mode 100644 index 000000000000..a706297998e9 --- /dev/null +++ b/Documentation/devicetree/bindings/net/altera_tse.txt @@ -0,0 +1,114 @@ +* Altera Triple-Speed Ethernet MAC driver (TSE) + +Required properties: +- compatible: Should be "altr,tse-1.0" for legacy SGDMA based TSE, and should + be "altr,tse-msgdma-1.0" for the preferred MSGDMA based TSE. + ALTR is supported for legacy device trees, but is deprecated. + altr should be used for all new designs. +- reg: Address and length of the register set for the device. It contains + the information of registers in the same order as described by reg-names +- reg-names: Should contain the reg names + "control_port": MAC configuration space region + "tx_csr": xDMA Tx dispatcher control and status space region + "tx_desc": MSGDMA Tx dispatcher descriptor space region + "rx_csr" : xDMA Rx dispatcher control and status space region + "rx_desc": MSGDMA Rx dispatcher descriptor space region + "rx_resp": MSGDMA Rx dispatcher response space region + "s1": SGDMA descriptor memory +- interrupts: Should contain the TSE interrupts and it's mode. +- interrupt-names: Should contain the interrupt names + "rx_irq": xDMA Rx dispatcher interrupt + "tx_irq": xDMA Tx dispatcher interrupt +- rx-fifo-depth: MAC receive FIFO buffer depth in bytes +- tx-fifo-depth: MAC transmit FIFO buffer depth in bytes +- phy-mode: See ethernet.txt in the same directory. +- phy-handle: See ethernet.txt in the same directory. +- phy-addr: See ethernet.txt in the same directory. A configuration should + include phy-handle or phy-addr. +- altr,has-supplementary-unicast: + If present, TSE supports additional unicast addresses. + Otherwise additional unicast addresses are not supported. +- altr,has-hash-multicast-filter: + If present, TSE supports a hash based multicast filter. + Otherwise, hash-based multicast filtering is not supported. + +- mdio device tree subnode: When the TSE has a phy connected to its local + mdio, there must be device tree subnode with the following + required properties: + + - compatible: Must be "altr,tse-mdio". + - #address-cells: Must be <1>. + - #size-cells: Must be <0>. + + For each phy on the mdio bus, there must be a node with the following + fields: + + - reg: phy id used to communicate to phy. + - device_type: Must be "ethernet-phy". + +Optional properties: +- local-mac-address: See ethernet.txt in the same directory. +- max-frame-size: See ethernet.txt in the same directory. + +Example: + + tse_sub_0_eth_tse_0: ethernet@0x1,00000000 { + compatible = "altr,tse-msgdma-1.0"; + reg = <0x00000001 0x00000000 0x00000400>, + <0x00000001 0x00000460 0x00000020>, + <0x00000001 0x00000480 0x00000020>, + <0x00000001 0x000004A0 0x00000008>, + <0x00000001 0x00000400 0x00000020>, + <0x00000001 0x00000420 0x00000020>; + reg-names = "control_port", "rx_csr", "rx_desc", "rx_resp", "tx_csr", "tx_desc"; + interrupt-parent = <&hps_0_arm_gic_0>; + interrupts = <0 41 4>, <0 40 4>; + interrupt-names = "rx_irq", "tx_irq"; + rx-fifo-depth = <2048>; + tx-fifo-depth = <2048>; + address-bits = <48>; + max-frame-size = <1500>; + local-mac-address = [ 00 00 00 00 00 00 ]; + phy-mode = "gmii"; + altr,has-supplementary-unicast; + altr,has-hash-multicast-filter; + phy-handle = <&phy0>; + mdio { + compatible = "altr,tse-mdio"; + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@0 { + reg = <0x0>; + device_type = "ethernet-phy"; + }; + + phy1: ethernet-phy@1 { + reg = <0x1>; + device_type = "ethernet-phy"; + }; + + }; + }; + + tse_sub_1_eth_tse_0: ethernet@0x1,00001000 { + compatible = "altr,tse-msgdma-1.0"; + reg = <0x00000001 0x00001000 0x00000400>, + <0x00000001 0x00001460 0x00000020>, + <0x00000001 0x00001480 0x00000020>, + <0x00000001 0x000014A0 0x00000008>, + <0x00000001 0x00001400 0x00000020>, + <0x00000001 0x00001420 0x00000020>; + reg-names = "control_port", "rx_csr", "rx_desc", "rx_resp", "tx_csr", "tx_desc"; + interrupt-parent = <&hps_0_arm_gic_0>; + interrupts = <0 43 4>, <0 42 4>; + interrupt-names = "rx_irq", "tx_irq"; + rx-fifo-depth = <2048>; + tx-fifo-depth = <2048>; + address-bits = <48>; + max-frame-size = <1500>; + local-mac-address = [ 00 00 00 00 00 00 ]; + phy-mode = "gmii"; + altr,has-supplementary-unicast; + altr,has-hash-multicast-filter; + phy-handle = <&phy1>; + }; diff --git a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt new file mode 100644 index 000000000000..42409bfe04c4 --- /dev/null +++ b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt @@ -0,0 +1,23 @@ +* AMD 10GbE PHY driver (amd-xgbe-phy) + +Required properties: +- compatible: Should be "amd,xgbe-phy-seattle-v1a" and + "ethernet-phy-ieee802.3-c45" +- reg: Address and length of the register sets for the device + - SerDes Rx/Tx registers + - SerDes integration registers (1/2) + - SerDes integration registers (2/2) + +Optional properties: +- amd,speed-set: Speed capabilities of the device + 0 - 1GbE and 10GbE (default) + 1 - 2.5GbE and 10GbE + +Example: + xgbe_phy@e1240800 { + compatible = "amd,xgbe-phy-seattle-v1a", "ethernet-phy-ieee802.3-c45"; + reg = <0 0xe1240800 0 0x00400>, + <0 0xe1250000 0 0x00060>, + <0 0xe1250080 0 0x00004>; + amd,speed-set = <0>; + }; diff --git a/Documentation/devicetree/bindings/net/amd-xgbe.txt b/Documentation/devicetree/bindings/net/amd-xgbe.txt new file mode 100644 index 000000000000..41354f730beb --- /dev/null +++ b/Documentation/devicetree/bindings/net/amd-xgbe.txt @@ -0,0 +1,39 @@ +* AMD 10GbE driver (amd-xgbe) + +Required properties: +- compatible: Should be "amd,xgbe-seattle-v1a" +- reg: Address and length of the register sets for the device + - MAC registers + - PCS registers +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the amd-xgbe interrupt +- clocks: + - DMA clock for the amd-xgbe device (used for calculating the + correct Rx interrupt watchdog timer value on a DMA channel + for coalescing) + - PTP clock for the amd-xgbe device +- clock-names: Should be the names of the clocks + - "dma_clk" for the DMA clock + - "ptp_clk" for the PTP clock +- phy-handle: See ethernet.txt file in the same directory +- phy-mode: See ethernet.txt file in the same directory + +Optional properties: +- mac-address: mac address to be assigned to the device. Can be overridden + by UEFI. +- dma-coherent: Present if dma operations are coherent + +Example: + xgbe@e0700000 { + compatible = "amd,xgbe-seattle-v1a"; + reg = <0 0xe0700000 0 0x80000>, + <0 0xe0780000 0 0x80000>; + interrupt-parent = <&gic>; + interrupts = <0 325 4>; + clocks = <&xgbe_dma_clk>, <&xgbe_ptp_clk>; + clock-names = "dma_clk", "ptp_clk"; + phy-handle = <&phy>; + phy-mode = "xgmii"; + mac-address = [ 02 a1 a2 a3 a4 a5 ]; + }; diff --git a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt new file mode 100644 index 000000000000..cfcc52705ed8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt @@ -0,0 +1,68 @@ +APM X-Gene SoC Ethernet nodes + +Ethernet nodes are defined to describe on-chip ethernet interfaces in +APM X-Gene SoC. + +Required properties for all the ethernet interfaces: +- compatible: Should be "apm,xgene-enet" +- reg: Address and length of the register set for the device. It contains the + information of registers in the same order as described by reg-names +- reg-names: Should contain the register set names + - "enet_csr": Ethernet control and status register address space + - "ring_csr": Descriptor ring control and status register address space + - "ring_cmd": Descriptor ring command register address space +- interrupts: Ethernet main interrupt +- clocks: Reference to the clock entry. +- local-mac-address: MAC address assigned to this device +- phy-connection-type: Interface type between ethernet device and PHY device + +Required properties for ethernet interfaces that have external PHY: +- phy-handle: Reference to a PHY node connected to this device + +- mdio: Device tree subnode with the following required properties: + - compatible: Must be "apm,xgene-mdio". + - #address-cells: Must be <1>. + - #size-cells: Must be <0>. + + For the phy on the mdio bus, there must be a node with the following fields: + - compatible: PHY identifier. Please refer ./phy.txt for the format. + - reg: The ID number for the phy. + +Optional properties: +- status: Should be "ok" or "disabled" for enabled/disabled. Default is "ok". + +Example: + menetclk: menetclk { + compatible = "apm,xgene-device-clock"; + clock-output-names = "menetclk"; + status = "ok"; + }; + + menet: ethernet@17020000 { + compatible = "apm,xgene-enet"; + status = "disabled"; + reg = <0x0 0x17020000 0x0 0xd100>, + <0x0 0X17030000 0x0 0X400>, + <0x0 0X10000000 0x0 0X200>; + reg-names = "enet_csr", "ring_csr", "ring_cmd"; + interrupts = <0x0 0x3c 0x4>; + clocks = <&menetclk 0>; + local-mac-address = [00 01 73 00 00 01]; + phy-connection-type = "rgmii"; + phy-handle = <&menetphy>; + mdio { + compatible = "apm,xgene-mdio"; + #address-cells = <1>; + #size-cells = <0>; + menetphy: menetphy@3 { + compatible = "ethernet-phy-id001c.c915"; + reg = <0x3>; + }; + + }; + }; + +/* Board-specific peripheral configurations */ +&menet { + status = "ok"; +}; diff --git a/Documentation/devicetree/bindings/net/arc_emac.txt b/Documentation/devicetree/bindings/net/arc_emac.txt index bcbc3f009158..a1d71eb43b20 100644 --- a/Documentation/devicetree/bindings/net/arc_emac.txt +++ b/Documentation/devicetree/bindings/net/arc_emac.txt @@ -4,21 +4,18 @@ Required properties: - compatible: Should be "snps,arc-emac" - reg: Address and length of the register set for the device - interrupts: Should contain the EMAC interrupts -- clock-frequency: CPU frequency. It is needed to calculate and set polling -period of EMAC. -- max-speed: Maximum supported data-rate in Mbit/s. In some HW configurations -bandwidth of external memory controller might be a limiting factor. That's why -it's required to specify which data-rate is supported on current SoC or FPGA. -For example if only 10 Mbit/s is supported (10BASE-T) set "10". If 100 Mbit/s is -supported (100BASE-TX) set "100". -- phy: PHY device attached to the EMAC via MDIO bus +- max-speed: see ethernet.txt file in the same directory. +- phy: see ethernet.txt file in the same directory. + +Clock handling: +The clock frequency is needed to calculate and set polling period of EMAC. +It must be provided by one of: +- clock-frequency: CPU frequency. +- clocks: reference to the clock supplying the EMAC. Child nodes of the driver are the individual PHY devices connected to the MDIO bus. They must have a "reg" property given the PHY address on the MDIO bus. -Optional properties: -- mac-address: 6 bytes, mac address - Examples: ethernet@c0fc2000 { @@ -26,7 +23,11 @@ Examples: reg = <0xc0fc2000 0x3c>; interrupts = <6>; mac-address = [ 00 11 22 33 44 55 ]; + clock-frequency = <80000000>; + /* or */ + clocks = <&emac_clock>; + max-speed = <100>; phy = <&phy0>; diff --git a/Documentation/devicetree/bindings/net/broadcom-bcmgenet.txt b/Documentation/devicetree/bindings/net/broadcom-bcmgenet.txt new file mode 100644 index 000000000000..451fef26b4df --- /dev/null +++ b/Documentation/devicetree/bindings/net/broadcom-bcmgenet.txt @@ -0,0 +1,121 @@ +* Broadcom BCM7xxx Ethernet Controller (GENET) + +Required properties: +- compatible: should contain one of "brcm,genet-v1", "brcm,genet-v2", + "brcm,genet-v3", "brcm,genet-v4". +- reg: address and length of the register set for the device +- interrupts: must be two cells, the first cell is the general purpose + interrupt line, while the second cell is the interrupt for the ring + RX and TX queues operating in ring mode +- phy-mode: see ethernet.txt file in the same directory +- #address-cells: should be 1 +- #size-cells: should be 1 + +Optional properties: +- clocks: When provided, must be two phandles to the functional clocks nodes + of the GENET block. The first phandle is the main GENET clock used during + normal operation, while the second phandle is the Wake-on-LAN clock. +- clock-names: When provided, names of the functional clock phandles, first + name should be "enet" and second should be "enet-wol". + +- phy-handle: See ethernet.txt file in the same directory; used to describe + configurations where a PHY (internal or external) is used. + +- fixed-link: When the GENET interface is connected to a MoCA hardware block or + when operating in a RGMII to RGMII type of connection, or when the MDIO bus is + voluntarily disabled, this property should be used to describe the "fixed link". + See Documentation/devicetree/bindings/net/fixed-link.txt for information on + the property specifics + +Required child nodes: + +- mdio bus node: this node should always be present regarless of the PHY + configuration of the GENET instance + +MDIO bus node required properties: + +- compatible: should contain one of "brcm,genet-mdio-v1", "brcm,genet-mdio-v2" + "brcm,genet-mdio-v3", "brcm,genet-mdio-v4", the version has to match the + parent node compatible property (e.g: brcm,genet-v4 pairs with + brcm,genet-mdio-v4) +- reg: address and length relative to the parent node base register address +- #address-cells: address cell for MDIO bus addressing, should be 1 +- #size-cells: size of the cells for MDIO bus addressing, should be 0 + +Ethernet PHY node properties: + +See Documentation/devicetree/bindings/net/phy.txt for the list of required and +optional properties. + +Internal Gigabit PHY example: + +ethernet@f0b60000 { + phy-mode = "internal"; + phy-handle = <&phy1>; + mac-address = [ 00 10 18 36 23 1a ]; + compatible = "brcm,genet-v4"; + #address-cells = <0x1>; + #size-cells = <0x1>; + reg = <0xf0b60000 0xfc4c>; + interrupts = <0x0 0x14 0x0>, <0x0 0x15 0x0>; + + mdio@e14 { + compatible = "brcm,genet-mdio-v4"; + #address-cells = <0x1>; + #size-cells = <0x0>; + reg = <0xe14 0x8>; + + phy1: ethernet-phy@1 { + max-speed = <1000>; + reg = <0x1>; + compatible = "brcm,28nm-gphy", "ethernet-phy-ieee802.3-c22"; + }; + }; +}; + +MoCA interface / MAC to MAC example: + +ethernet@f0b80000 { + phy-mode = "moca"; + fixed-link = <1 0 1000 0 0>; + mac-address = [ 00 10 18 36 24 1a ]; + compatible = "brcm,genet-v4"; + #address-cells = <0x1>; + #size-cells = <0x1>; + reg = <0xf0b80000 0xfc4c>; + interrupts = <0x0 0x16 0x0>, <0x0 0x17 0x0>; + + mdio@e14 { + compatible = "brcm,genet-mdio-v4"; + #address-cells = <0x1>; + #size-cells = <0x0>; + reg = <0xe14 0x8>; + }; +}; + + +External MDIO-connected Gigabit PHY/switch: + +ethernet@f0ba0000 { + phy-mode = "rgmii"; + phy-handle = <&phy0>; + mac-address = [ 00 10 18 36 26 1a ]; + compatible = "brcm,genet-v4"; + #address-cells = <0x1>; + #size-cells = <0x1>; + reg = <0xf0ba0000 0xfc4c>; + interrupts = <0x0 0x18 0x0>, <0x0 0x19 0x0>; + + mdio@0e14 { + compatible = "brcm,genet-mdio-v4"; + #address-cells = <0x1>; + #size-cells = <0x0>; + reg = <0xe14 0x8>; + + phy0: ethernet-phy@0 { + max-speed = <1000>; + reg = <0x0>; + compatible = "brcm,bcm53125", "ethernet-phy-ieee802.3-c22"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/broadcom-mdio-unimac.txt b/Documentation/devicetree/bindings/net/broadcom-mdio-unimac.txt new file mode 100644 index 000000000000..ab0bb4247d14 --- /dev/null +++ b/Documentation/devicetree/bindings/net/broadcom-mdio-unimac.txt @@ -0,0 +1,39 @@ +* Broadcom UniMAC MDIO bus controller + +Required properties: +- compatible: should one from "brcm,genet-mdio-v1", "brcm,genet-mdio-v2", + "brcm,genet-mdio-v3", "brcm,genet-mdio-v4" or "brcm,unimac-mdio" +- reg: address and length of the regsiter set for the device, first one is the + base register, and the second one is optional and for indirect accesses to + larger than 16-bits MDIO transactions +- reg-names: name(s) of the register must be "mdio" and optional "mdio_indir_rw" +- #size-cells: must be 1 +- #address-cells: must be 0 + +Optional properties: +- interrupts: must be one if the interrupt is shared with the Ethernet MAC or + Ethernet switch this MDIO block is integrated from, or must be two, if there + are two separate interrupts, first one must be "mdio done" and second must be + for "mdio error" +- interrupt-names: must be "mdio_done_error" when there is a share interrupt fed + to this hardware block, or must be "mdio_done" for the first interrupt and + "mdio_error" for the second when there are separate interrupts + +Child nodes of this MDIO bus controller node are standard Ethernet PHY device +nodes as described in Documentation/devicetree/bindings/net/phy.txt + +Example: + +mdio@403c0 { + compatible = "brcm,unimac-mdio"; + reg = <0x403c0 0x8 0x40300 0x18>; + reg-names = "mdio", "mdio_indir_rw"; + #size-cells = <1>; + #address-cells = <0>; + + ... + phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/broadcom-sf2.txt b/Documentation/devicetree/bindings/net/broadcom-sf2.txt new file mode 100644 index 000000000000..30d487597ecb --- /dev/null +++ b/Documentation/devicetree/bindings/net/broadcom-sf2.txt @@ -0,0 +1,78 @@ +* Broadcom Starfighter 2 integrated swich + +Required properties: + +- compatible: should be "brcm,bcm7445-switch-v4.0" +- reg: addresses and length of the register sets for the device, must be 6 + pairs of register addresses and lengths +- interrupts: interrupts for the devices, must be two interrupts +- dsa,mii-bus: phandle to the MDIO bus controller, see dsa/dsa.txt +- dsa,ethernet: phandle to the CPU network interface controller, see dsa/dsa.txt +- #size-cells: must be 0 +- #address-cells: must be 2, see dsa/dsa.txt + +Subnodes: + +The integrated switch subnode should be specified according to the binding +described in dsa/dsa.txt. + +Optional properties: + +- reg-names: litteral names for the device base register addresses, when present + must be: "core", "reg", "intrl2_0", "intrl2_1", "fcb", "acb" + +- interrupt-names: litternal names for the device interrupt lines, when present + must be: "switch_0" and "switch_1" + +- brcm,num-gphy: specify the maximum number of integrated gigabit PHYs in the + switch + +- brcm,num-rgmii-ports: specify the maximum number of RGMII interfaces supported + by the switch + +- brcm,fcb-pause-override: boolean property, if present indicates that the switch + supports Failover Control Block pause override capability + +- brcm,acb-packets-inflight: boolean property, if present indicates that the switch + Admission Control Block supports reporting the number of packets in-flight in a + switch queue + +Example: + +switch_top@f0b00000 { + compatible = "simple-bus"; + #size-cells = <1>; + #address-cells = <1>; + ranges = <0 0xf0b00000 0x40804>; + + ethernet_switch@0 { + compatible = "brcm,bcm7445-switch-v4.0"; + #size-cells = <0>; + #address-cells = <2>; + reg = <0x0 0x40000 + 0x40000 0x110 + 0x40340 0x30 + 0x40380 0x30 + 0x40400 0x34 + 0x40600 0x208>; + interrupts = <0 0x18 0 + 0 0x19 0>; + brcm,num-gphy = <1>; + brcm,num-rgmii-ports = <2>; + brcm,fcb-pause-override; + brcm,acb-packets-inflight; + + ... + switch@0 { + reg = <0 0>; + #size-cells = <0>; + #address-cells <1>; + + port@0 { + label = "gphy"; + reg = <0>; + }; + ... + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/broadcom-systemport.txt b/Documentation/devicetree/bindings/net/broadcom-systemport.txt new file mode 100644 index 000000000000..aa7ad622259d --- /dev/null +++ b/Documentation/devicetree/bindings/net/broadcom-systemport.txt @@ -0,0 +1,30 @@ +* Broadcom BCM7xxx Ethernet Systemport Controller (SYSTEMPORT) + +Required properties: +- compatible: should be one of "brcm,systemport-v1.00" or "brcm,systemport" +- reg: address and length of the register set for the device. +- interrupts: interrupts for the device, first cell must be for the the rx + interrupts, and the second cell should be for the transmit queues. An + optional third interrupt cell for Wake-on-LAN can be specified +- local-mac-address: Ethernet MAC address (48 bits) of this adapter +- phy-mode: Should be a string describing the PHY interface to the + Ethernet switch/PHY, see Documentation/devicetree/bindings/net/ethernet.txt +- fixed-link: see Documentation/devicetree/bindings/net/fixed-link.txt for + the property specific details + +Optional properties: +- systemport,num-tier2-arb: number of tier 2 arbiters, an integer +- systemport,num-tier1-arb: number of tier 1 arbiters, an integer +- systemport,num-txq: number of HW transmit queues, an integer +- systemport,num-rxq: number of HW receive queues, an integer + +Example: +ethernet@f04a0000 { + compatible = "brcm,systemport-v1.00"; + reg = <0xf04a0000 0x4650>; + local-mac-address = [ 00 11 22 33 44 55 ]; + fixed-link = <0 1 1000 0 0>; + phy-mode = "gmii"; + interrupts = <0x0 0x16 0x0>, + <0x0 0x17 0x0>; +}; diff --git a/Documentation/devicetree/bindings/net/can/m_can.txt b/Documentation/devicetree/bindings/net/can/m_can.txt new file mode 100644 index 000000000000..9e331777c203 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/m_can.txt @@ -0,0 +1,67 @@ +Bosch MCAN controller Device Tree Bindings +------------------------------------------------- + +Required properties: +- compatible : Should be "bosch,m_can" for M_CAN controllers +- reg : physical base address and size of the M_CAN + registers map and Message RAM +- reg-names : Should be "m_can" and "message_ram" +- interrupts : Should be the interrupt number of M_CAN interrupt + line 0 and line 1, could be same if sharing + the same interrupt. +- interrupt-names : Should contain "int0" and "int1" +- clocks : Clocks used by controller, should be host clock + and CAN clock. +- clock-names : Should contain "hclk" and "cclk" +- pinctrl-<n> : Pinctrl states as described in bindings/pinctrl/pinctrl-bindings.txt +- pinctrl-names : Names corresponding to the numbered pinctrl states +- bosch,mram-cfg : Message RAM configuration data. + Multiple M_CAN instances can share the same Message + RAM and each element(e.g Rx FIFO or Tx Buffer and etc) + number in Message RAM is also configurable, + so this property is telling driver how the shared or + private Message RAM are used by this M_CAN controller. + + The format should be as follows: + <offset sidf_elems xidf_elems rxf0_elems rxf1_elems + rxb_elems txe_elems txb_elems> + The 'offset' is an address offset of the Message RAM + where the following elements start from. This is + usually set to 0x0 if you're using a private Message + RAM. The remain cells are used to specify how many + elements are used for each FIFO/Buffer. + + M_CAN includes the following elements according to user manual: + 11-bit Filter 0-128 elements / 0-128 words + 29-bit Filter 0-64 elements / 0-128 words + Rx FIFO 0 0-64 elements / 0-1152 words + Rx FIFO 1 0-64 elements / 0-1152 words + Rx Buffers 0-64 elements / 0-1152 words + Tx Event FIFO 0-32 elements / 0-64 words + Tx Buffers 0-32 elements / 0-576 words + + Please refer to 2.4.1 Message RAM Configuration in + Bosch M_CAN user manual for details. + +Example: +SoC dtsi: +m_can1: can@020e8000 { + compatible = "bosch,m_can"; + reg = <0x020e8000 0x4000>, <0x02298000 0x4000>; + reg-names = "m_can", "message_ram"; + interrupts = <0 114 0x04>, + <0 114 0x04>; + interrupt-names = "int0", "int1"; + clocks = <&clks IMX6SX_CLK_CANFD>, + <&clks IMX6SX_CLK_CANFD>; + clock-names = "hclk", "cclk"; + bosch,mram-cfg = <0x0 0 0 32 0 0 0 1>; + status = "disabled"; +}; + +Board dts: +&m_can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_m_can1>; + status = "enabled"; +}; diff --git a/Documentation/devicetree/bindings/net/can/rcar_can.txt b/Documentation/devicetree/bindings/net/can/rcar_can.txt new file mode 100644 index 000000000000..002d8440bf66 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/rcar_can.txt @@ -0,0 +1,43 @@ +Renesas R-Car CAN controller Device Tree Bindings +------------------------------------------------- + +Required properties: +- compatible: "renesas,can-r8a7778" if CAN controller is a part of R8A7778 SoC. + "renesas,can-r8a7779" if CAN controller is a part of R8A7779 SoC. + "renesas,can-r8a7790" if CAN controller is a part of R8A7790 SoC. + "renesas,can-r8a7791" if CAN controller is a part of R8A7791 SoC. +- reg: physical base address and size of the R-Car CAN register map. +- interrupts: interrupt specifier for the sole interrupt. +- clocks: phandles and clock specifiers for 3 CAN clock inputs. +- clock-names: 3 clock input name strings: "clkp1", "clkp2", "can_clk". +- pinctrl-0: pin control group to be used for this controller. +- pinctrl-names: must be "default". + +Optional properties: +- renesas,can-clock-select: R-Car CAN Clock Source Select. Valid values are: + <0x0> (default) : Peripheral clock (clkp1) + <0x1> : Peripheral clock (clkp2) + <0x3> : Externally input clock + +Example +------- + +SoC common .dtsi file: + + can0: can@e6e80000 { + compatible = "renesas,can-r8a7791"; + reg = <0 0xe6e80000 0 0x1000>; + interrupts = <0 186 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7791_CLK_RCAN0>, + <&cpg_clocks R8A7791_CLK_RCAN>, <&can_clk>; + clock-names = "clkp1", "clkp2", "can_clk"; + status = "disabled"; + }; + +Board specific .dts file: + +&can0 { + pinctrl-0 = <&can0_pins>; + pinctrl-names = "default"; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/net/can/sja1000.txt b/Documentation/devicetree/bindings/net/can/sja1000.txt index f2105a47ec87..b4a6d53fb01a 100644 --- a/Documentation/devicetree/bindings/net/can/sja1000.txt +++ b/Documentation/devicetree/bindings/net/can/sja1000.txt @@ -12,6 +12,10 @@ Required properties: Optional properties: +- reg-io-width : Specify the size (in bytes) of the IO accesses that + should be performed on the device. Valid value is 1, 2 or 4. + Default to 1 (8 bits). + - nxp,external-clock-frequency : Frequency of the external oscillator clock in Hz. Note that the internal clock frequency used by the SJA1000 is half of that value. If not specified, a default value diff --git a/Documentation/devicetree/bindings/net/can/xilinx_can.txt b/Documentation/devicetree/bindings/net/can/xilinx_can.txt new file mode 100644 index 000000000000..fe38847d8e26 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/xilinx_can.txt @@ -0,0 +1,44 @@ +Xilinx Axi CAN/Zynq CANPS controller Device Tree Bindings +--------------------------------------------------------- + +Required properties: +- compatible : Should be "xlnx,zynq-can-1.0" for Zynq CAN + controllers and "xlnx,axi-can-1.00.a" for Axi CAN + controllers. +- reg : Physical base address and size of the Axi CAN/Zynq + CANPS registers map. +- interrupts : Property with a value describing the interrupt + number. +- interrupt-parent : Must be core interrupt controller +- clock-names : List of input clock names - "can_clk", "pclk" + (For CANPS), "can_clk" , "s_axi_aclk"(For AXI CAN) + (See clock bindings for details). +- clocks : Clock phandles (see clock bindings for details). +- tx-fifo-depth : Can Tx fifo depth. +- rx-fifo-depth : Can Rx fifo depth. + + +Example: + +For Zynq CANPS Dts file: + zynq_can_0: can@e0008000 { + compatible = "xlnx,zynq-can-1.0"; + clocks = <&clkc 19>, <&clkc 36>; + clock-names = "can_clk", "pclk"; + reg = <0xe0008000 0x1000>; + interrupts = <0 28 4>; + interrupt-parent = <&intc>; + tx-fifo-depth = <0x40>; + rx-fifo-depth = <0x40>; + }; +For Axi CAN Dts file: + axi_can_0: axi-can@40000000 { + compatible = "xlnx,axi-can-1.00.a"; + clocks = <&clkc 0>, <&clkc 1>; + clock-names = "can_clk","s_axi_aclk" ; + reg = <0x40000000 0x10000>; + interrupt-parent = <&intc>; + interrupts = <0 59 1>; + tx-fifo-depth = <0x40>; + rx-fifo-depth = <0x40>; + }; diff --git a/Documentation/devicetree/bindings/net/cavium-mix.txt b/Documentation/devicetree/bindings/net/cavium-mix.txt index 5da628db68bf..8d7c3096390f 100644 --- a/Documentation/devicetree/bindings/net/cavium-mix.txt +++ b/Documentation/devicetree/bindings/net/cavium-mix.txt @@ -18,12 +18,7 @@ Properties: - interrupts: Two interrupt specifiers. The first is the MIX interrupt routing and the second the routing for the AGL interrupts. -- mac-address: Optional, the MAC address to assign to the device. - -- local-mac-address: Optional, the MAC address to assign to the device - if mac-address is not specified. - -- phy-handle: Optional, a phandle for the PHY device connected to this device. +- phy-handle: Optional, see ethernet.txt file in the same directory. Example: ethernet@1070000100800 { diff --git a/Documentation/devicetree/bindings/net/cavium-pip.txt b/Documentation/devicetree/bindings/net/cavium-pip.txt index d4c53ba04b3b..7dbd158810d2 100644 --- a/Documentation/devicetree/bindings/net/cavium-pip.txt +++ b/Documentation/devicetree/bindings/net/cavium-pip.txt @@ -35,12 +35,7 @@ Properties for PIP port which is a child the PIP interface: - reg: The port number within the interface group. -- mac-address: Optional, the MAC address to assign to the device. - -- local-mac-address: Optional, the MAC address to assign to the device - if mac-address is not specified. - -- phy-handle: Optional, a phandle for the PHY device connected to this device. +- phy-handle: Optional, see ethernet.txt file in the same directory. Example: diff --git a/Documentation/devicetree/bindings/net/cdns-emac.txt b/Documentation/devicetree/bindings/net/cdns-emac.txt index 09055c2495f0..abd67c13d344 100644 --- a/Documentation/devicetree/bindings/net/cdns-emac.txt +++ b/Documentation/devicetree/bindings/net/cdns-emac.txt @@ -6,11 +6,7 @@ Required properties: or the generic form: "cdns,emac". - reg: Address and length of the register set for the device - interrupts: Should contain macb interrupt -- phy-mode: String, operation mode of the PHY interface. - Supported values are: "mii", "rmii". - -Optional properties: -- local-mac-address: 6 bytes, mac address +- phy-mode: see ethernet.txt file in the same directory. Examples: diff --git a/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt b/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt index 7ff57a119f81..764c0c79b43d 100644 --- a/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt +++ b/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt @@ -2,7 +2,9 @@ TI CPSW Phy mode Selection Device Tree Bindings ----------------------------------------------- Required properties: -- compatible : Should be "ti,am3352-cpsw-phy-sel" +- compatible : Should be "ti,am3352-cpsw-phy-sel" for am335x platform and + "ti,dra7xx-cpsw-phy-sel" for dra7xx platform + "ti,am43xx-cpsw-phy-sel" for am43xx platform - reg : physical base address and size of the cpsw registers map - reg-names : names of the register map given in "reg" node diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index 05d660e4ac64..33fe8462edf4 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -24,16 +24,17 @@ Optional properties: - ti,hwmods : Must be "cpgmac0" - no_bd_ram : Must be 0 or 1 - dual_emac : Specifies Switch to act as Dual EMAC +- syscon : Phandle to the system control device node, which is + the control module device of the am33x Slave Properties: Required properties: - phy_id : Specifies slave phy id -- phy-mode : The interface between the SoC and the PHY (a string - that of_get_phy_mode() can understand) -- mac-address : Specifies slave MAC address +- phy-mode : See ethernet.txt file in the same directory Optional properties: - dual_emac_res_vlan : Specifies VID to be used to segregate the ports +- mac-address : See ethernet.txt file in the same directory Note: "ti,hwmods" field is used to fetch the base address and irq resources from TI, omap hwmod data base during device registration. @@ -58,6 +59,7 @@ Examples: active_slave = <0>; cpts_clock_mult = <0x80000000>; cpts_clock_shift = <29>; + syscon = <&cm>; cpsw_emac0: slave@0 { phy_id = <&davinci_mdio>, <0>; phy-mode = "rgmii-txid"; @@ -86,6 +88,7 @@ Examples: active_slave = <0>; cpts_clock_mult = <0x80000000>; cpts_clock_shift = <29>; + syscon = <&cm>; cpsw_emac0: slave@0 { phy_id = <&davinci_mdio>, <0>; phy-mode = "rgmii-txid"; diff --git a/Documentation/devicetree/bindings/net/davicom-dm9000.txt b/Documentation/devicetree/bindings/net/davicom-dm9000.txt index 2d39c990e641..28767ed7c1bd 100644 --- a/Documentation/devicetree/bindings/net/davicom-dm9000.txt +++ b/Documentation/devicetree/bindings/net/davicom-dm9000.txt @@ -9,8 +9,6 @@ Required properties: - interrupts : interrupt specifier specific to interrupt controller Optional properties: -- local-mac-address : A bytestring of 6 bytes specifying Ethernet MAC address - to use (from firmware or bootloader) - davicom,no-eeprom : Configuration EEPROM is not available - davicom,ext-phy : Use external PHY diff --git a/Documentation/devicetree/bindings/net/davinci-mdio.txt b/Documentation/devicetree/bindings/net/davinci-mdio.txt index 72efaaf764f7..0369e25aabd2 100644 --- a/Documentation/devicetree/bindings/net/davinci-mdio.txt +++ b/Documentation/devicetree/bindings/net/davinci-mdio.txt @@ -1,8 +1,8 @@ -TI SoC Davinci MDIO Controller Device Tree Bindings +TI SoC Davinci/Keystone2 MDIO Controller Device Tree Bindings --------------------------------------------------- Required properties: -- compatible : Should be "ti,davinci_mdio" +- compatible : Should be "ti,davinci_mdio" or "ti,keystone_mdio" - reg : physical base address and size of the davinci mdio registers map - bus_freq : Mdio Bus frequency @@ -19,7 +19,7 @@ file. Examples: mdio: davinci_mdio@4A101000 { - compatible = "ti,cpsw"; + compatible = "ti,davinci_mdio"; reg = <0x4A101000 0x1000>; bus_freq = <1000000>; }; @@ -27,7 +27,7 @@ Examples: (or) mdio: davinci_mdio@4A101000 { - compatible = "ti,cpsw"; + compatible = "ti,davinci_mdio"; ti,hwmods = "davinci_mdio"; bus_freq = <1000000>; }; diff --git a/Documentation/devicetree/bindings/net/davinci_emac.txt b/Documentation/devicetree/bindings/net/davinci_emac.txt index 6e356d15154a..032808843f90 100644 --- a/Documentation/devicetree/bindings/net/davinci_emac.txt +++ b/Documentation/devicetree/bindings/net/davinci_emac.txt @@ -17,9 +17,8 @@ Required properties: Miscellaneous Interrupt> Optional properties: -- phy-handle: Contains a phandle to an Ethernet PHY. +- phy-handle: See ethernet.txt file in the same directory. If absent, davinci_emac driver defaults to 100/FULL. -- local-mac-address : 6 bytes, mac address - ti,davinci-rmii-en: 1 byte, 1 means use RMII - ti,davinci-no-bd-ram: boolean, does EMAC have BD RAM? diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt index 49f4f7ae3f51..a62c889aafca 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa.txt +++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt @@ -39,6 +39,22 @@ Optionnal property: This property is only used when switches are being chained/cascaded together. +- phy-handle : Phandle to a PHY on an external MDIO bus, not the + switch internal one. See + Documentation/devicetree/bindings/net/ethernet.txt + for details. + +- phy-mode : String representing the connection to the designated + PHY node specified by the 'phy-handle' property. See + Documentation/devicetree/bindings/net/ethernet.txt + for details. + +Optional subnodes: +- fixed-link : Fixed-link subnode describing a link to a non-MDIO + managed entity. See + Documentation/devicetree/bindings/net/fixed-link.txt + for details. + Example: dsa@0 { @@ -58,6 +74,7 @@ Example: port@0 { reg = <0>; label = "lan1"; + phy-handle = <&phy0>; }; port@1 { diff --git a/Documentation/devicetree/bindings/net/emac_rockchip.txt b/Documentation/devicetree/bindings/net/emac_rockchip.txt new file mode 100644 index 000000000000..8dc1c79fef7f --- /dev/null +++ b/Documentation/devicetree/bindings/net/emac_rockchip.txt @@ -0,0 +1,50 @@ +* ARC EMAC 10/100 Ethernet platform driver for Rockchip Rk3066/RK3188 SoCs + +Required properties: +- compatible: Should be "rockchip,rk3066-emac" or "rockchip,rk3188-emac" + according to the target SoC. +- reg: Address and length of the register set for the device +- interrupts: Should contain the EMAC interrupts +- rockchip,grf: phandle to the syscon grf used to control speed and mode + for emac. +- phy: see ethernet.txt file in the same directory. +- phy-mode: see ethernet.txt file in the same directory. + +Optional properties: +- phy-supply: phandle to a regulator if the PHY needs one + +Clock handling: +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Shall be "hclk" for the host clock needed to calculate and set + polling period of EMAC and "macref" for the reference clock needed to transfer + data to and from the phy. + +Child nodes of the driver are the individual PHY devices connected to the +MDIO bus. They must have a "reg" property given the PHY address on the MDIO bus. + +Examples: + +ethernet@10204000 { + compatible = "rockchip,rk3188-emac"; + reg = <0xc0fc2000 0x3c>; + interrupts = <6>; + mac-address = [ 00 11 22 33 44 55 ]; + + clocks = <&cru HCLK_EMAC>, <&cru SCLK_MAC>; + clock-names = "hclk", "macref"; + + pinctrl-names = "default"; + pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&phy_int>; + + rockchip,grf = <&grf>; + + phy = <&phy0>; + phy-mode = "rmii"; + phy-supply = <&vcc_rmii>; + + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@0 { + reg = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/ethernet.txt b/Documentation/devicetree/bindings/net/ethernet.txt new file mode 100644 index 000000000000..3fc360523bc9 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ethernet.txt @@ -0,0 +1,25 @@ +The following properties are common to the Ethernet controllers: + +- local-mac-address: array of 6 bytes, specifies the MAC address that was + assigned to the network device; +- mac-address: array of 6 bytes, specifies the MAC address that was last used by + the boot program; should be used in cases where the MAC address assigned to + the device by the boot program is different from the "local-mac-address" + property; +- max-speed: number, specifies maximum speed in Mbit/s supported by the device; +- max-frame-size: number, maximum transfer unit (IEEE defined MTU), rather than + the maximum frame size (there's contradiction in ePAPR). +- phy-mode: string, operation mode of the PHY interface; supported values are + "mii", "gmii", "sgmii", "qsgmii", "tbi", "rev-mii", "rmii", "rgmii", "rgmii-id", + "rgmii-rxid", "rgmii-txid", "rtbi", "smii", "xgmii"; this is now a de-facto + standard property; +- phy-connection-type: the same as "phy-mode" property but described in ePAPR; +- phy-handle: phandle, specifies a reference to a node representing a PHY + device; this property is described in ePAPR and so preferred; +- phy: the same as "phy-handle" property, not recommended for new bindings. +- phy-device: the same as "phy-handle" property, not recommended for new + bindings. + +Child nodes of the Ethernet controller are typically the individual PHY devices +connected via the MDIO bus (sometimes the MDIO bus controller is separate). +They are described in the phy.txt file in this same directory. diff --git a/Documentation/devicetree/bindings/net/fixed-link.txt b/Documentation/devicetree/bindings/net/fixed-link.txt new file mode 100644 index 000000000000..82bf7e0f47b6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/fixed-link.txt @@ -0,0 +1,42 @@ +Fixed link Device Tree binding +------------------------------ + +Some Ethernet MACs have a "fixed link", and are not connected to a +normal MDIO-managed PHY device. For those situations, a Device Tree +binding allows to describe a "fixed link". + +Such a fixed link situation is described by creating a 'fixed-link' +sub-node of the Ethernet MAC device node, with the following +properties: + +* 'speed' (integer, mandatory), to indicate the link speed. Accepted + values are 10, 100 and 1000 +* 'full-duplex' (boolean, optional), to indicate that full duplex is + used. When absent, half duplex is assumed. +* 'pause' (boolean, optional), to indicate that pause should be + enabled. +* 'asym-pause' (boolean, optional), to indicate that asym_pause should + be enabled. + +Old, deprecated 'fixed-link' binding: + +* A 'fixed-link' property in the Ethernet MAC node, with 5 cells, of the + form <a b c d e> with the following accepted values: + - a: emulated PHY ID, choose any but but unique to the all specified + fixed-links, from 0 to 31 + - b: duplex configuration: 0 for half duplex, 1 for full duplex + - c: link speed in Mbits/sec, accepted values are: 10, 100 and 1000 + - d: pause configuration: 0 for no pause, 1 for pause + - e: asymmetric pause configuration: 0 for no asymmetric pause, 1 for + asymmetric pause + +Example: + +ethernet@0 { + ... + fixed-link { + speed = <1000>; + full-duplex; + }; + ... +}; diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt index 845ff848d895..0c8775c45798 100644 --- a/Documentation/devicetree/bindings/net/fsl-fec.txt +++ b/Documentation/devicetree/bindings/net/fsl-fec.txt @@ -4,18 +4,28 @@ Required properties: - compatible : Should be "fsl,<soc>-fec" - reg : Address and length of the register set for the device - interrupts : Should contain fec interrupt -- phy-mode : String, operation mode of the PHY interface. - Supported values are: "mii", "gmii", "sgmii", "tbi", "rmii", - "rgmii", "rgmii-id", "rgmii-rxid", "rgmii-txid", "rtbi", "smii". +- phy-mode : See ethernet.txt file in the same directory Optional properties: -- local-mac-address : 6 bytes, mac address - phy-reset-gpios : Should specify the gpio for phy reset - phy-reset-duration : Reset duration in milliseconds. Should present only if property "phy-reset-gpios" is available. Missing the property will have the duration be 1 millisecond. Numbers greater than 1000 are invalid and 1 millisecond will be used instead. -- phy-supply: regulator that powers the Ethernet PHY. +- phy-supply : regulator that powers the Ethernet PHY. +- phy-handle : phandle to the PHY device connected to this device. +- fixed-link : Assume a fixed link. See fixed-link.txt in the same directory. + Use instead of phy-handle. +- fsl,num-tx-queues : The property is valid for enet-avb IP, which supports + hw multi queues. Should specify the tx queue number, otherwise set tx queue + number to 1. +- fsl,num-rx-queues : The property is valid for enet-avb IP, which supports + hw multi queues. Should specify the rx queue number, otherwise set rx queue + number to 1. + +Optional subnodes: +- mdio : specifies the mdio bus in the FEC, used as a container for phy nodes + according to phy.txt in the same directory Example: @@ -28,3 +38,23 @@ ethernet@83fec000 { local-mac-address = [00 04 9F 01 1B B9]; phy-supply = <®_fec_supply>; }; + +Example with phy specified: + +ethernet@83fec000 { + compatible = "fsl,imx51-fec", "fsl,imx27-fec"; + reg = <0x83fec000 0x4000>; + interrupts = <87>; + phy-mode = "mii"; + phy-reset-gpios = <&gpio2 14 0>; /* GPIO2_14 */ + local-mac-address = [00 04 9F 01 1B B9]; + phy-supply = <®_fec_supply>; + phy-handle = <ðphy>; + mdio { + ethphy: ethernet-phy@6 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <6>; + max-speed = <100>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt index d2ea4605d078..be6ea8960f20 100644 --- a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt +++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt @@ -38,22 +38,14 @@ Properties: - model : Model of the device. Can be "TSEC", "eTSEC", or "FEC" - compatible : Should be "gianfar" - reg : Offset and length of the register set for the device - - local-mac-address : List of bytes representing the ethernet address of - this controller - interrupts : For FEC devices, the first interrupt is the device's interrupt. For TSEC and eTSEC devices, the first interrupt is transmit, the second is receive, and the third is error. - - phy-handle : The phandle for the PHY connected to this ethernet - controller. - - fixed-link : <a b c d e> where a is emulated phy id - choose any, - but unique to the all specified fixed-links, b is duplex - 0 half, - 1 full, c is link speed - d#10/d#100/d#1000, d is pause - 0 no - pause, 1 pause, e is asym_pause - 0 no asym_pause, 1 asym_pause. - - phy-connection-type : a string naming the controller/PHY interface type, - i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "sgmii", - "tbi", or "rtbi". This property is only really needed if the connection - is of type "rgmii-id", as all other connection types are detected by - hardware. + - phy-handle : See ethernet.txt file in the same directory. + - fixed-link : See fixed-link.txt in the same directory. + - phy-connection-type : See ethernet.txt file in the same directory. + This property is only really needed if the connection is of type + "rgmii-id", as all other connection types are detected by hardware. - fsl,magic-packet : If present, indicates that the hardware supports waking up via magic packet. - bd-stash : If present, indicates that the hardware supports stashing diff --git a/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt b/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt new file mode 100644 index 000000000000..75d398bb1fbb --- /dev/null +++ b/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt @@ -0,0 +1,36 @@ +Hisilicon hix5hd2 gmac controller + +Required properties: +- compatible: should be "hisilicon,hix5hd2-gmac". +- reg: specifies base physical address(s) and size of the device registers. + The first region is the MAC register base and size. + The second region is external interface control register. +- interrupts: should contain the MAC interrupt. +- #address-cells: must be <1>. +- #size-cells: must be <0>. +- phy-mode: see ethernet.txt [1]. +- phy-handle: see ethernet.txt [1]. +- mac-address: see ethernet.txt [1]. +- clocks: clock phandle and specifier pair. + +- PHY subnode: inherits from phy binding [2] + +[1] Documentation/devicetree/bindings/net/ethernet.txt +[2] Documentation/devicetree/bindings/net/phy.txt + +Example: + gmac0: ethernet@f9840000 { + compatible = "hisilicon,hix5hd2-gmac"; + reg = <0xf9840000 0x1000>,<0xf984300c 0x4>; + interrupts = <0 71 4>; + #address-cells = <1>; + #size-cells = <0>; + phy-mode = "mii"; + phy-handle = <&phy2>; + mac-address = [00 00 00 00 00 00]; + clocks = <&clock HIX5HD2_MAC0_CLK>; + + phy2: ethernet-phy@2 { + reg = <2>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/ieee802154/at86rf230.txt b/Documentation/devicetree/bindings/net/ieee802154/at86rf230.txt new file mode 100644 index 000000000000..d3bbdded4cbe --- /dev/null +++ b/Documentation/devicetree/bindings/net/ieee802154/at86rf230.txt @@ -0,0 +1,23 @@ +* AT86RF230 IEEE 802.15.4 * + +Required properties: + - compatible: should be "atmel,at86rf230", "atmel,at86rf231", + "atmel,at86rf233" or "atmel,at86rf212" + - spi-max-frequency: maximal bus speed, should be set to 7500000 depends + sync or async operation mode + - reg: the chipselect index + - interrupts: the interrupt generated by the device + +Optional properties: + - reset-gpio: GPIO spec for the rstn pin + - sleep-gpio: GPIO spec for the slp_tr pin + +Example: + + at86rf231@0 { + compatible = "atmel,at86rf231"; + spi-max-frequency = <7500000>; + reg = <0>; + interrupts = <19 1>; + interrupt-parent = <&gpio3>; + }; diff --git a/Documentation/devicetree/bindings/net/ieee802154/cc2520.txt b/Documentation/devicetree/bindings/net/ieee802154/cc2520.txt new file mode 100644 index 000000000000..0071883c08d8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ieee802154/cc2520.txt @@ -0,0 +1,29 @@ +*CC2520 IEEE 802.15.4 Compatible Radio* + +Required properties: + - compatible: should be "ti,cc2520" + - spi-max-frequency: maximal bus speed (8000000), should be set to 4000000 depends + sync or async operation mode + - reg: the chipselect index + - pinctrl-0: pin control group to be used for this controller. + - pinctrl-names: must contain a "default" entry. + - fifo-gpio: GPIO spec for the FIFO pin + - fifop-gpio: GPIO spec for the FIFOP pin + - sfd-gpio: GPIO spec for the SFD pin + - cca-gpio: GPIO spec for the CCA pin + - vreg-gpio: GPIO spec for the VREG pin + - reset-gpio: GPIO spec for the RESET pin +Example: + cc2520@0 { + compatible = "ti,cc2520"; + reg = <0>; + spi-max-frequency = <4000000>; + pinctrl-names = "default"; + pinctrl-0 = <&cc2520_cape_pins>; + fifo-gpio = <&gpio1 18 0>; + fifop-gpio = <&gpio1 19 0>; + sfd-gpio = <&gpio1 13 0>; + cca-gpio = <&gpio1 16 0>; + vreg-gpio = <&gpio0 31 0>; + reset-gpio = <&gpio1 12 0>; + }; diff --git a/Documentation/devicetree/bindings/net/lpc-eth.txt b/Documentation/devicetree/bindings/net/lpc-eth.txt index 585021acd178..b92e927808b6 100644 --- a/Documentation/devicetree/bindings/net/lpc-eth.txt +++ b/Documentation/devicetree/bindings/net/lpc-eth.txt @@ -6,10 +6,9 @@ Required properties: - interrupts: Should contain ethernet controller interrupt Optional properties: -- phy-mode: String, operation mode of the PHY interface. - Supported values are: "mii", "rmii" (default) +- phy-mode: See ethernet.txt file in the same directory. If the property is + absent, "rmii" is assumed. - use-iram: Use LPC32xx internal SRAM (IRAM) for DMA buffering -- local-mac-address : 6 bytes, mac address Example: diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index 70af2ec12b09..aaa696414f57 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -8,16 +8,12 @@ Required properties: the Cadence GEM, or the generic form: "cdns,gem". - reg: Address and length of the register set for the device - interrupts: Should contain macb interrupt -- phy-mode: String, operation mode of the PHY interface. - Supported values are: "mii", "rmii", "gmii", "rgmii". +- phy-mode: See ethernet.txt file in the same directory. - clock-names: Tuple listing input clock names. Required elements: 'pclk', 'hclk' Optional elements: 'tx_clk' - clocks: Phandles to input clocks. -Optional properties: -- local-mac-address: 6 bytes, mac address - Examples: macb0: ethernet@fffc4000 { diff --git a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt index 859a6fa7569c..750d577e8083 100644 --- a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt +++ b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt @@ -4,10 +4,8 @@ Required properties: - compatible: should be "marvell,armada-370-neta". - reg: address and length of the register set for the device. - interrupts: interrupt for the device -- phy: A phandle to a phy node defining the PHY address (as the reg - property, a single integer). -- phy-mode: The interface between the SoC and the PHY (a string that - of_get_phy_mode() can understand) +- phy: See ethernet.txt file in the same directory. +- phy-mode: See ethernet.txt file in the same directory - clocks: a pointer to the reference clock for this device. Example: diff --git a/Documentation/devicetree/bindings/net/marvell-orion-net.txt b/Documentation/devicetree/bindings/net/marvell-orion-net.txt index c233b6114242..bce52b2ec55e 100644 --- a/Documentation/devicetree/bindings/net/marvell-orion-net.txt +++ b/Documentation/devicetree/bindings/net/marvell-orion-net.txt @@ -36,7 +36,7 @@ Required port properties: "marvell,kirkwood-eth-port". - reg: port number relative to ethernet controller, shall be 0, 1, or 2. - interrupts: port interrupt. - - local-mac-address: 6 bytes MAC address. + - local-mac-address: See ethernet.txt file in the same directory. Optional port properties: - marvell,tx-queue-size: size of the transmit ring buffer. @@ -48,7 +48,7 @@ Optional port properties: and - - phy-handle: phandle reference to ethernet PHY. + - phy-handle: See ethernet.txt file in the same directory. or diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt new file mode 100644 index 000000000000..aa4f4230bfd7 --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt @@ -0,0 +1,61 @@ +* Marvell Armada 375 Ethernet Controller (PPv2) + +Required properties: + +- compatible: should be "marvell,armada-375-pp2" +- reg: addresses and length of the register sets for the device. + Must contain the following register sets: + - common controller registers + - LMS registers + In addition, at least one port register set is required. +- clocks: a pointer to the reference clocks for this device, consequently: + - main controller clock + - GOP clock +- clock-names: names of used clocks, must be "pp_clk" and "gop_clk". + +The ethernet ports are represented by subnodes. At least one port is +required. + +Required properties (port): + +- interrupts: interrupt for the port +- port-id: should be '0' or '1' for ethernet ports, and '2' for the + loopback port +- phy-mode: See ethernet.txt file in the same directory + +Optional properties (port): + +- marvell,loopback: port is loopback mode +- phy: a phandle to a phy node defining the PHY address (as the reg + property, a single integer). Note: if this property isn't present, + then fixed link is assumed, and the 'fixed-link' property is + mandatory. + +Example: + +ethernet@f0000 { + compatible = "marvell,armada-375-pp2"; + reg = <0xf0000 0xa000>, + <0xc0000 0x3060>, + <0xc4000 0x100>, + <0xc5000 0x100>; + clocks = <&gateclk 3>, <&gateclk 19>; + clock-names = "pp_clk", "gop_clk"; + status = "okay"; + + eth0: eth0@c4000 { + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + port-id = <0>; + status = "okay"; + phy = <&phy0>; + phy-mode = "gmii"; + }; + + eth1: eth1@c5000 { + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; + port-id = <1>; + status = "okay"; + phy = <&phy3>; + phy-mode = "gmii"; + }; +}; diff --git a/Documentation/devicetree/bindings/net/marvell-pxa168.txt b/Documentation/devicetree/bindings/net/marvell-pxa168.txt new file mode 100644 index 000000000000..845a148a346e --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-pxa168.txt @@ -0,0 +1,36 @@ +* Marvell PXA168 Ethernet Controller + +Required properties: +- compatible: should be "marvell,pxa168-eth". +- reg: address and length of the register set for the device. +- interrupts: interrupt for the device. +- clocks: pointer to the clock for the device. + +Optional properties: +- port-id: Ethernet port number. Should be '0','1' or '2'. +- #address-cells: must be 1 when using sub-nodes. +- #size-cells: must be 0 when using sub-nodes. +- phy-handle: see ethernet.txt file in the same directory. +- local-mac-address: see ethernet.txt file in the same directory. + +Sub-nodes: +Each PHY can be represented as a sub-node. This is not mandatory. + +Sub-nodes required properties: +- reg: the MDIO address of the PHY. + +Example: + + eth0: ethernet@f7b90000 { + compatible = "marvell,pxa168-eth"; + reg = <0xf7b90000 0x10000>; + clocks = <&chip CLKID_GETH0>; + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + phy-handle = <ðphy0>; + + ethphy0: ethernet-phy@0 { + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/mdio-gpio.txt b/Documentation/devicetree/bindings/net/mdio-gpio.txt index c79bab025369..8dbcf8295c6c 100644 --- a/Documentation/devicetree/bindings/net/mdio-gpio.txt +++ b/Documentation/devicetree/bindings/net/mdio-gpio.txt @@ -14,7 +14,7 @@ node. Example: aliases { - mdio-gpio0 = <&mdio0>; + mdio-gpio0 = &mdio0; }; mdio0: mdio { diff --git a/Documentation/devicetree/bindings/net/meson-dwmac.txt b/Documentation/devicetree/bindings/net/meson-dwmac.txt new file mode 100644 index 000000000000..ec633d74a8a8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/meson-dwmac.txt @@ -0,0 +1,25 @@ +* Amlogic Meson DWMAC Ethernet controller + +The device inherits all the properties of the dwmac/stmmac devices +described in the file net/stmmac.txt with the following changes. + +Required properties: + +- compatible: should be "amlogic,meson6-dwmac" along with "snps,dwmac" + and any applicable more detailed version number + described in net/stmmac.txt + +- reg: should contain a register range for the dwmac controller and + another one for the Amlogic specific configuration + +Example: + + ethmac: ethernet@c9410000 { + compatible = "amlogic,meson6-dwmac", "snps,dwmac"; + reg = <0xc9410000 0x10000 + 0xc1108108 0x4>; + interrupts = <0 8 1>; + interrupt-names = "macirq"; + clocks = <&clk81>; + clock-names = "stmmaceth"; + } diff --git a/Documentation/devicetree/bindings/net/micrel-ks8851.txt b/Documentation/devicetree/bindings/net/micrel-ks8851.txt index 11ace3c3d805..bbdf9a7359a2 100644 --- a/Documentation/devicetree/bindings/net/micrel-ks8851.txt +++ b/Documentation/devicetree/bindings/net/micrel-ks8851.txt @@ -1,9 +1,18 @@ -Micrel KS8851 Ethernet mac +Micrel KS8851 Ethernet mac (MLL) Required properties: -- compatible = "micrel,ks8851-ml" of parallel interface +- compatible = "micrel,ks8851-mll" of parallel interface - reg : 2 physical address and size of registers for data and command - interrupts : interrupt connection +Micrel KS8851 Ethernet mac (SPI) + +Required properties: +- compatible = "micrel,ks8851" or the deprecated "ks8851" +- reg : chip select number +- interrupts : interrupt connection + Optional properties: -- local-mac-address : Ethernet mac address to use +- vdd-supply: analog 3.3V supply for Ethernet mac +- vdd-io-supply: digital 1.8V IO supply for Ethernet mac +- reset-gpios: reset_n input pin diff --git a/Documentation/devicetree/bindings/net/micrel-ksz9021.txt b/Documentation/devicetree/bindings/net/micrel-ksz9021.txt deleted file mode 100644 index 997a63f1aea1..000000000000 --- a/Documentation/devicetree/bindings/net/micrel-ksz9021.txt +++ /dev/null @@ -1,49 +0,0 @@ -Micrel KSZ9021 Gigabit Ethernet PHY - -Some boards require special tuning values, particularly when it comes to -clock delays. You can specify clock delay values by adding -micrel-specific properties to an Ethernet OF device node. - -All skew control options are specified in picoseconds. The minimum -value is 0, and the maximum value is 3000. - -Optional properties: - - rxc-skew-ps : Skew control of RXC pad - - rxdv-skew-ps : Skew control of RX CTL pad - - txc-skew-ps : Skew control of TXC pad - - txen-skew-ps : Skew control of TX_CTL pad - - rxd0-skew-ps : Skew control of RX data 0 pad - - rxd1-skew-ps : Skew control of RX data 1 pad - - rxd2-skew-ps : Skew control of RX data 2 pad - - rxd3-skew-ps : Skew control of RX data 3 pad - - txd0-skew-ps : Skew control of TX data 0 pad - - txd1-skew-ps : Skew control of TX data 1 pad - - txd2-skew-ps : Skew control of TX data 2 pad - - txd3-skew-ps : Skew control of TX data 3 pad - -Examples: - - /* Attach to an Ethernet device with autodetected PHY */ - &enet { - rxc-skew-ps = <3000>; - rxdv-skew-ps = <0>; - txc-skew-ps = <3000>; - txen-skew-ps = <0>; - status = "okay"; - }; - - /* Attach to an explicitly-specified PHY */ - mdio { - phy0: ethernet-phy@0 { - rxc-skew-ps = <3000>; - rxdv-skew-ps = <0>; - txc-skew-ps = <3000>; - txen-skew-ps = <0>; - reg = <0>; - }; - }; - ethernet@70000 { - status = "okay"; - phy = <&phy0>; - phy-mode = "rgmii-id"; - }; diff --git a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt new file mode 100644 index 000000000000..692076fda0e5 --- /dev/null +++ b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt @@ -0,0 +1,83 @@ +Micrel KSZ9021/KSZ9031 Gigabit Ethernet PHY + +Some boards require special tuning values, particularly when it comes to +clock delays. You can specify clock delay values by adding +micrel-specific properties to an Ethernet OF device node. + +Note that these settings are applied after any phy-specific fixup from +phy_fixup_list (see phy_init_hw() from drivers/net/phy/phy_device.c), +and therefore may overwrite them. + +KSZ9021: + + All skew control options are specified in picoseconds. The minimum + value is 0, the maximum value is 3000, and it is incremented by 200ps + steps. + + Optional properties: + + - rxc-skew-ps : Skew control of RXC pad + - rxdv-skew-ps : Skew control of RX CTL pad + - txc-skew-ps : Skew control of TXC pad + - txen-skew-ps : Skew control of TX CTL pad + - rxd0-skew-ps : Skew control of RX data 0 pad + - rxd1-skew-ps : Skew control of RX data 1 pad + - rxd2-skew-ps : Skew control of RX data 2 pad + - rxd3-skew-ps : Skew control of RX data 3 pad + - txd0-skew-ps : Skew control of TX data 0 pad + - txd1-skew-ps : Skew control of TX data 1 pad + - txd2-skew-ps : Skew control of TX data 2 pad + - txd3-skew-ps : Skew control of TX data 3 pad + +KSZ9031: + + All skew control options are specified in picoseconds. The minimum + value is 0, and the maximum is property-dependent. The increment + step is 60ps. + + Optional properties: + + Maximum value of 1860: + + - rxc-skew-ps : Skew control of RX clock pad + - txc-skew-ps : Skew control of TX clock pad + + Maximum value of 900: + + - rxdv-skew-ps : Skew control of RX CTL pad + - txen-skew-ps : Skew control of TX CTL pad + - rxd0-skew-ps : Skew control of RX data 0 pad + - rxd1-skew-ps : Skew control of RX data 1 pad + - rxd2-skew-ps : Skew control of RX data 2 pad + - rxd3-skew-ps : Skew control of RX data 3 pad + - txd0-skew-ps : Skew control of TX data 0 pad + - txd1-skew-ps : Skew control of TX data 1 pad + - txd2-skew-ps : Skew control of TX data 2 pad + - txd3-skew-ps : Skew control of TX data 3 pad + +Examples: + + /* Attach to an Ethernet device with autodetected PHY */ + &enet { + rxc-skew-ps = <3000>; + rxdv-skew-ps = <0>; + txc-skew-ps = <3000>; + txen-skew-ps = <0>; + status = "okay"; + }; + + /* Attach to an explicitly-specified PHY */ + mdio { + phy0: ethernet-phy@0 { + rxc-skew-ps = <3000>; + rxdv-skew-ps = <0>; + txc-skew-ps = <3000>; + txen-skew-ps = <0>; + reg = <0>; + }; + }; + ethernet@70000 { + status = "okay"; + phy = <&phy0>; + phy-mode = "rgmii-id"; + }; diff --git a/Documentation/devicetree/bindings/net/micrel.txt b/Documentation/devicetree/bindings/net/micrel.txt new file mode 100644 index 000000000000..e1d99b95c4ec --- /dev/null +++ b/Documentation/devicetree/bindings/net/micrel.txt @@ -0,0 +1,24 @@ +Micrel PHY properties. + +These properties cover the base properties Micrel PHYs. + +Optional properties: + + - micrel,led-mode : LED mode value to set for PHYs with configurable LEDs. + + Configure the LED mode with single value. The list of PHYs and + the bits that are currently supported: + + KSZ8001: register 0x1e, bits 15..14 + KSZ8041: register 0x1e, bits 15..14 + KSZ8021: register 0x1f, bits 5..4 + KSZ8031: register 0x1f, bits 5..4 + KSZ8051: register 0x1f, bits 5..4 + + See the respective PHY datasheet for the mode values. + + - clocks, clock-names: contains clocks according to the common clock bindings. + + supported clocks: + - KSZ8021, KSZ8031: "rmii-ref": The RMII refence input clock. Used + to determine the XI input clock. diff --git a/Documentation/devicetree/bindings/net/nfc/pn544.txt b/Documentation/devicetree/bindings/net/nfc/pn544.txt new file mode 100644 index 000000000000..dab69f36167c --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/pn544.txt @@ -0,0 +1,35 @@ +* NXP Semiconductors PN544 NFC Controller + +Required properties: +- compatible: Should be "nxp,pn544-i2c". +- clock-frequency: I²C work frequency. +- reg: address on the bus +- interrupt-parent: phandle for the interrupt gpio controller +- interrupts: GPIO interrupt to which the chip is connected +- enable-gpios: Output GPIO pin used for enabling/disabling the PN544 +- firmware-gpios: Output GPIO pin used to enter firmware download mode + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBone with PN544 on I2C2): + +&i2c2 { + + status = "okay"; + + pn544: pn544@28 { + + compatible = "nxp,pn544-i2c"; + + reg = <0x28>; + clock-frequency = <400000>; + + interrupt-parent = <&gpio1>; + interrupts = <17 GPIO_ACTIVE_HIGH>; + + enable-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>; + firmware-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/st21nfca.txt b/Documentation/devicetree/bindings/net/nfc/st21nfca.txt new file mode 100644 index 000000000000..e4faa2e8dfeb --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/st21nfca.txt @@ -0,0 +1,33 @@ +* STMicroelectronics SAS. ST21NFCA NFC Controller + +Required properties: +- compatible: Should be "st,st21nfca_i2c". +- clock-frequency: I²C work frequency. +- reg: address on the bus +- interrupt-parent: phandle for the interrupt gpio controller +- interrupts: GPIO interrupt to which the chip is connected +- enable-gpios: Output GPIO pin used for enabling/disabling the ST21NFCA + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBoard xM with ST21NFCA on I2C2): + +&i2c2 { + + status = "okay"; + + st21nfca: st21nfca@1 { + + compatible = "st,st21nfca_i2c"; + + reg = <0x01>; + clock-frequency = <400000>; + + interrupt-parent = <&gpio5>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; + + enable-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt b/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt new file mode 100644 index 000000000000..9005608cbbd1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt @@ -0,0 +1,33 @@ +* STMicroelectronics SAS. ST21NFCB NFC Controller + +Required properties: +- compatible: Should be "st,st21nfcb_i2c". +- clock-frequency: I²C work frequency. +- reg: address on the bus +- interrupt-parent: phandle for the interrupt gpio controller +- interrupts: GPIO interrupt to which the chip is connected +- reset-gpios: Output GPIO pin used to reset the ST21NFCB + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBoard xM with ST21NFCB on I2C2): + +&i2c2 { + + status = "okay"; + + st21nfcb: st21nfcb@8 { + + compatible = "st,st21nfcb_i2c"; + + reg = <0x08>; + clock-frequency = <400000>; + + interrupt-parent = <&gpio5>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; + + reset-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt new file mode 100644 index 000000000000..7c89ca290ced --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt @@ -0,0 +1,44 @@ +* Texas Instruments TRF7970A RFID/NFC/15693 Transceiver + +Required properties: +- compatible: Should be "ti,trf7970a". +- spi-max-frequency: Maximum SPI frequency (<= 2000000). +- interrupt-parent: phandle of parent interrupt handler. +- interrupts: A single interrupt specifier. +- ti,enable-gpios: Two GPIO entries used for 'EN' and 'EN2' pins on the + TRF7970A. +- vin-supply: Regulator for supply voltage to VIN pin + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. +- autosuspend-delay: Specify autosuspend delay in milliseconds. +- vin-voltage-override: Specify voltage of VIN pin in microvolts. +- irq-status-read-quirk: Specify that the trf7970a being used has the + "IRQ Status Read" erratum. +- en2-rf-quirk: Specify that the trf7970a being used has the "EN2 RF" + erratum. + +Example (for ARM-based BeagleBone with TRF7970A on SPI1): + +&spi1 { + status = "okay"; + + nfc@0 { + compatible = "ti,trf7970a"; + reg = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&trf7970a_default>; + spi-max-frequency = <2000000>; + interrupt-parent = <&gpio2>; + interrupts = <14 0>; + ti,enable-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>, + <&gpio2 5 GPIO_ACTIVE_LOW>; + vin-supply = <&ldo3_reg>; + vin-voltage-override = <5000000>; + autosuspend-delay = <30000>; + irq-status-read-quirk; + en2-rf-quirk; + status = "okay"; + }; +}; diff --git a/Documentation/devicetree/bindings/net/opencores-ethoc.txt b/Documentation/devicetree/bindings/net/opencores-ethoc.txt new file mode 100644 index 000000000000..2dc127c30d9b --- /dev/null +++ b/Documentation/devicetree/bindings/net/opencores-ethoc.txt @@ -0,0 +1,22 @@ +* OpenCores MAC 10/100 Mbps + +Required properties: +- compatible: Should be "opencores,ethoc". +- reg: two memory regions (address and length), + first region is for the device registers and descriptor rings, + second is for the device packet memory. +- interrupts: interrupt for the device. + +Optional properties: +- clocks: phandle to refer to the clk used as per + Documentation/devicetree/bindings/clock/clock-bindings.txt + +Examples: + + enet0: ethoc@fd030000 { + compatible = "opencores,ethoc"; + reg = <0xfd030000 0x4000 0xfd800000 0x4000>; + interrupts = <1>; + local-mac-address = [00 50 c2 13 6f 00]; + clocks = <&osc>; + }; diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt index 58307d0931c8..5b8c58903077 100644 --- a/Documentation/devicetree/bindings/net/phy.txt +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -21,10 +21,18 @@ Optional Properties: elements. - max-speed: Maximum PHY supported speed (10, 100, 1000...) + If the phy's identifier is known then the list may contain an entry + of the form: "ethernet-phy-idAAAA.BBBB" where + AAAA - The value of the 16 bit Phy Identifier 1 register as + 4 hex digits. This is the chip vendor OUI bits 3:18 + BBBB - The value of the 16 bit Phy Identifier 2 register as + 4 hex digits. This is the chip vendor OUI bits 19:24, + followed by 10 bits of a vendor specific ID. + Example: ethernet-phy@0 { - compatible = "ethernet-phy-ieee802.3-c22"; + compatible = "ethernet-phy-id0141.0e90", "ethernet-phy-ieee802.3-c22"; interrupt-parent = <40000>; interrupts = <35 1>; reg = <0>; diff --git a/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt b/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt new file mode 100644 index 000000000000..c74989c0d8ac --- /dev/null +++ b/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt @@ -0,0 +1,47 @@ +* Qualcomm QCA7000 (Ethernet over SPI protocol) + +Note: The QCA7000 is useable as a SPI device. In this case it must be defined +as a child of a SPI master in the device tree. + +Required properties: +- compatible : Should be "qca,qca7000" +- reg : Should specify the SPI chip select +- interrupts : The first cell should specify the index of the source interrupt + and the second cell should specify the trigger type as rising edge +- spi-cpha : Must be set +- spi-cpol: Must be set + +Optional properties: +- interrupt-parent : Specify the pHandle of the source interrupt +- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at. + Numbers smaller than 1000000 or greater than 16000000 are invalid. Missing + the property will set the SPI frequency to 8000000 Hertz. +- local-mac-address: 6 bytes, MAC address +- qca,legacy-mode : Set the SPI data transfer of the QCA7000 to legacy mode. + In this mode the SPI master must toggle the chip select between each data + word. In burst mode these gaps aren't necessary, which is faster. + This setting depends on how the QCA7000 is setup via GPIO pin strapping. + If the property is missing the driver defaults to burst mode. + +Example: + +/* Freescale i.MX28 SPI master*/ +ssp2: spi@80014000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx28-spi"; + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pins_a>; + status = "okay"; + + qca7000: ethernet@0 { + compatible = "qca,qca7000"; + reg = <0x0>; + interrupt-parent = <&gpio3>; /* GPIO Bank 3 */ + interrupts = <25 0x1>; /* Index: 25, rising edge */ + spi-cpha; /* SPI mode: CPHA=1 */ + spi-cpol; /* SPI mode: CPOL=1 */ + spi-max-frequency = <8000000>; /* freq: 8 MHz */ + local-mac-address = [ A0 B0 C0 D0 E0 F0 ]; + }; +}; diff --git a/Documentation/devicetree/bindings/net/samsung-sxgbe.txt b/Documentation/devicetree/bindings/net/samsung-sxgbe.txt new file mode 100644 index 000000000000..888c250197fe --- /dev/null +++ b/Documentation/devicetree/bindings/net/samsung-sxgbe.txt @@ -0,0 +1,52 @@ +* Samsung 10G Ethernet driver (SXGBE) + +Required properties: +- compatible: Should be "samsung,sxgbe-v2.0a" +- reg: Address and length of the register set for the device +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the SXGBE interrupts + These interrupts are ordered by fixed and follows variable + trasmit DMA interrupts, receive DMA interrupts and lpi interrupt. + index 0 - this is fixed common interrupt of SXGBE and it is always + available. + index 1 to 25 - 8 variable trasmit interrupts, variable 16 receive interrupts + and 1 optional lpi interrupt. +- phy-mode: String, operation mode of the PHY interface. + Supported values are: "sgmii", "xgmii". +- samsung,pbl: Integer, Programmable Burst Length. + Supported values are 1, 2, 4, 8, 16, or 32. +- samsung,burst-map: Integer, Program the possible bursts supported by sxgbe + This is an integer and represents allowable DMA bursts when fixed burst. + Allowable range is 0x01-0x3F. When this field is set fixed burst is enabled. + When fixed length is needed for burst mode, it can be set within allowable + range. + +Optional properties: +- mac-address: 6 bytes, mac address +- max-frame-size: Maximum Transfer Unit (IEEE defined MTU), rather + than the maximum frame size. + +Example: + + aliases { + ethernet0 = <&sxgbe0>; + }; + + sxgbe0: ethernet@1a040000 { + compatible = "samsung,sxgbe-v2.0a"; + reg = <0 0x1a040000 0 0x10000>; + interrupt-parent = <&gic>; + interrupts = <0 209 4>, <0 185 4>, <0 186 4>, <0 187 4>, + <0 188 4>, <0 189 4>, <0 190 4>, <0 191 4>, + <0 192 4>, <0 193 4>, <0 194 4>, <0 195 4>, + <0 196 4>, <0 197 4>, <0 198 4>, <0 199 4>, + <0 200 4>, <0 201 4>, <0 202 4>, <0 203 4>, + <0 204 4>, <0 205 4>, <0 206 4>, <0 207 4>, + <0 208 4>, <0 210 4>; + samsung,pbl = <0x08> + samsung,burst-map = <0x20> + mac-address = [ 00 11 22 33 44 55 ]; /* Filled in by U-Boot */ + max-frame-size = <9000>; + phy-mode = "xgmii"; + }; diff --git a/Documentation/devicetree/bindings/net/sh_eth.txt b/Documentation/devicetree/bindings/net/sh_eth.txt new file mode 100644 index 000000000000..34d4db1a4e25 --- /dev/null +++ b/Documentation/devicetree/bindings/net/sh_eth.txt @@ -0,0 +1,56 @@ +* Renesas Electronics SH EtherMAC + +This file provides information on what the device node for the SH EtherMAC +interface contains. + +Required properties: +- compatible: "renesas,gether-r8a7740" if the device is a part of R8A7740 SoC. + "renesas,ether-r8a7778" if the device is a part of R8A7778 SoC. + "renesas,ether-r8a7779" if the device is a part of R8A7779 SoC. + "renesas,ether-r8a7790" if the device is a part of R8A7790 SoC. + "renesas,ether-r8a7791" if the device is a part of R8A7791 SoC. + "renesas,ether-r8a7794" if the device is a part of R8A7794 SoC. + "renesas,ether-r7s72100" if the device is a part of R7S72100 SoC. +- reg: offset and length of (1) the E-DMAC/feLic register block (required), + (2) the TSU register block (optional). +- interrupts: interrupt specifier for the sole interrupt. +- phy-mode: see ethernet.txt file in the same directory. +- phy-handle: see ethernet.txt file in the same directory. +- #address-cells: number of address cells for the MDIO bus, must be equal to 1. +- #size-cells: number of size cells on the MDIO bus, must be equal to 0. +- clocks: clock phandle and specifier pair. +- pinctrl-0: phandle, referring to a default pin configuration node. + +Optional properties: +- interrupt-parent: the phandle for the interrupt controller that services + interrupts for this device. +- pinctrl-names: pin configuration state name ("default"). +- renesas,no-ether-link: boolean, specify when a board does not provide a proper + Ether LINK signal. +- renesas,ether-link-active-low: boolean, specify when the Ether LINK signal is + active-low instead of normal active-high. + +Example (Lager board): + + ethernet@ee700000 { + compatible = "renesas,ether-r8a7790"; + reg = <0 0xee700000 0 0x400>; + interrupt-parent = <&gic>; + interrupts = <0 162 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp8_clks R8A7790_CLK_ETHER>; + phy-mode = "rmii"; + phy-handle = <&phy1>; + pinctrl-0 = <ðer_pins>; + pinctrl-names = "default"; + renesas,ether-link-active-low; + #address-cells = <1>; + #size-cells = <0>; + + phy1: ethernet-phy@1 { + reg = <1>; + interrupt-parent = <&irqc0>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + pinctrl-0 = <&phy1_pins>; + pinctrl-names = "default"; + }; + }; diff --git a/Documentation/devicetree/bindings/net/smsc-lan91c111.txt b/Documentation/devicetree/bindings/net/smsc-lan91c111.txt index 5a41a8658daa..e77e167593db 100644 --- a/Documentation/devicetree/bindings/net/smsc-lan91c111.txt +++ b/Documentation/devicetree/bindings/net/smsc-lan91c111.txt @@ -6,9 +6,10 @@ Required properties: - interrupts : interrupt connection Optional properties: -- phy-device : phandle to Ethernet phy -- local-mac-address : Ethernet mac address to use +- phy-device : see ethernet.txt file in the same directory - reg-io-width : Mask of sizes (in bytes) of the IO accesses that are supported on the device. Valid value for SMSC LAN91c111 are 1, 2 or 4. If it's omitted or invalid, the size would be 2 meaning 16-bit access only. +- power-gpios: GPIO to control the PWRDWN pin +- reset-gpios: GPIO to control the RESET pin diff --git a/Documentation/devicetree/bindings/net/smsc911x.txt b/Documentation/devicetree/bindings/net/smsc911x.txt index adb5b5744ecd..3fed3c124411 100644 --- a/Documentation/devicetree/bindings/net/smsc911x.txt +++ b/Documentation/devicetree/bindings/net/smsc911x.txt @@ -6,9 +6,7 @@ Required properties: - interrupts : Should contain SMSC LAN interrupt line - interrupt-parent : Should be the phandle for the interrupt controller that services interrupts for this device -- phy-mode : String, operation mode of the PHY interface. - Supported values are: "mii", "gmii", "sgmii", "tbi", "rmii", - "rgmii", "rgmii-id", "rgmii-rxid", "rgmii-txid", "rtbi", "smii". +- phy-mode : See ethernet.txt file in the same directory Optional properties: - reg-shift : Specify the quantity to shift the register offsets by @@ -23,7 +21,6 @@ Optional properties: external PHY - smsc,save-mac-address : Indicates that mac address needs to be saved before resetting the controller -- local-mac-address : 6 bytes, mac address Examples: diff --git a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt new file mode 100644 index 000000000000..3a9d67951606 --- /dev/null +++ b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt @@ -0,0 +1,31 @@ +Altera SOCFPGA SoC DWMAC controller + +This is a variant of the dwmac/stmmac driver an inherits all descriptions +present in Documentation/devicetree/bindings/net/stmmac.txt. + +The device node has additional properties: + +Required properties: + - compatible : Should contain "altr,socfpga-stmmac" along with + "snps,dwmac" and any applicable more detailed + designware version numbers documented in stmmac.txt + - altr,sysmgr-syscon : Should be the phandle to the system manager node that + encompasses the glue register, the register offset, and the register shift. + +Optional properties: +altr,emac-splitter: Should be the phandle to the emac splitter soft IP node if + DWMAC controller is connected emac splitter. + +Example: + +gmac0: ethernet@ff700000 { + compatible = "altr,socfpga-stmmac", "snps,dwmac-3.70a", "snps,dwmac"; + altr,sysmgr-syscon = <&sysmgr 0x60 0>; + status = "disabled"; + reg = <0xff700000 0x2000>; + interrupts = <0 115 4>; + interrupt-names = "macirq"; + mac-address = [00 00 00 00 00 00];/* Filled in by U-Boot */ + clocks = <&emac_0_clk>; + clock-names = "stmmaceth"; +}; diff --git a/Documentation/devicetree/bindings/net/sti-dwmac.txt b/Documentation/devicetree/bindings/net/sti-dwmac.txt new file mode 100644 index 000000000000..6762a6b5da7e --- /dev/null +++ b/Documentation/devicetree/bindings/net/sti-dwmac.txt @@ -0,0 +1,65 @@ +STMicroelectronics SoC DWMAC glue layer controller + +This file documents differences between the core properties in +Documentation/devicetree/bindings/net/stmmac.txt +and what is needed on STi platforms to program the stmmac glue logic. + +The device node has following properties. + +Required properties: + - compatible : Can be "st,stih415-dwmac", "st,stih416-dwmac", + "st,stih407-dwmac", "st,stid127-dwmac". + - reg : Offset of the glue configuration register map in system + configuration regmap pointed by st,syscon property and size. + - st,syscon : Should be phandle to system configuration node which + encompases this glue registers. + - st,gmac_en: this is to enable the gmac into a dedicated sysctl control + register available on STiH407 SoC. + - sti-ethconf: this is the gmac glue logic register to enable the GMAC, + select among the different modes and program the clk retiming. + - pinctrl-0: pin-control for all the MII mode supported. + +Optional properties: + - resets : phandle pointing to the system reset controller with correct + reset line index for ethernet reset. + - st,ext-phyclk: valid only for RMII where PHY can generate 50MHz clock or + MAC can generate it. + - st,tx-retime-src: This specifies which clk is wired up to the mac for + retimeing tx lines. This is totally board dependent and can take one of the + posssible values from "txclk", "clk_125" or "clkgen". + If not passed, the internal clock will be used by default. + - sti-ethclk: this is the phy clock. + - sti-clkconf: this is an extra sysconfig register, available in new SoCs, + to program the clk retiming. + - st,gmac_en: to enable the GMAC, this only is present in some SoCs; e.g. + STiH407. + +Example: + +ethernet0: dwmac@9630000 { + device_type = "network"; + status = "disabled"; + compatible = "st,stih407-dwmac", "snps,dwmac", "snps,dwmac-3.710"; + reg = <0x9630000 0x8000>, <0x80 0x4>; + reg-names = "stmmaceth", "sti-ethconf"; + + st,syscon = <&syscfg_sbc_reg>; + st,gmac_en; + resets = <&softreset STIH407_ETH1_SOFTRESET>; + reset-names = "stmmaceth"; + + interrupts = <GIC_SPI 98 IRQ_TYPE_NONE>, + <GIC_SPI 99 IRQ_TYPE_NONE>, + <GIC_SPI 100 IRQ_TYPE_NONE>; + interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; + + snps,pbl = <32>; + snps,mixed-burst; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rgmii1>; + + clock-names = "stmmaceth", "sti-ethclk"; + clocks = <&CLK_S_C0_FLEXGEN CLK_EXT2F_A9>, + <&CLK_S_C0_FLEXGEN CLK_ETH_PHY>; +}; diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index 9d92d42140f2..c41afd963edf 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -10,8 +10,7 @@ Required properties: - interrupt-names: Should contain the interrupt names "macirq" "eth_wake_irq" if this interrupt is supported in the "interrupts" property -- phy-mode: String, operation mode of the PHY interface. - Supported values are: "mii", "rmii", "gmii", "rgmii". +- phy-mode: See ethernet.txt file in the same directory. - snps,reset-gpio gpio number for phy reset. - snps,reset-active-low boolean flag to indicate if phy reset is active low. - snps,reset-delays-us is triplet of delays @@ -26,14 +25,24 @@ Required properties: - snps,force_sf_dma_mode Force DMA to use the Store and Forward mode for both tx and rx. This flag is ignored if force_thresh_dma_mode is set. +- snps,multicast-filter-bins: Number of multicast filter hash bins + supported by this device instance +- snps,perfect-filter-entries: Number of perfect filter entries supported + by this device instance Optional properties: -- mac-address: 6 bytes, mac address - resets: Should contain a phandle to the STMMAC reset signal, if any - reset-names: Should contain the reset signal name "stmmaceth", if a reset phandle is given -- max-frame-size: Maximum Transfer Unit (IEEE defined MTU), rather - than the maximum frame size. +- max-frame-size: See ethernet.txt file in the same directory +- clocks: If present, the first clock should be the GMAC main clock, + further clocks may be specified in derived bindings. +- clock-names: One name for each entry in the clocks property, the + first one should be "stmmaceth". +- clk_ptp_ref: this is the PTP reference clock; in case of the PTP is + available this clock is used for programming the Timestamp Addend Register. + If not passed then the system clock will be used and this is fine on some + platforms. Examples: @@ -46,4 +55,8 @@ Examples: mac-address = [000000000000]; /* Filled in by U-Boot */ max-frame-size = <3800>; phy-mode = "gmii"; + snps,multicast-filter-bins = <256>; + snps,perfect-filter-entries = <128>; + clocks = <&clock>; + clock-names = "stmmaceth"; }; diff --git a/Documentation/devicetree/bindings/net/via-rhine.txt b/Documentation/devicetree/bindings/net/via-rhine.txt new file mode 100644 index 000000000000..334eca2bf937 --- /dev/null +++ b/Documentation/devicetree/bindings/net/via-rhine.txt @@ -0,0 +1,17 @@ +* VIA Rhine 10/100 Network Controller + +Required properties: +- compatible : Should be "via,vt8500-rhine" for integrated + Rhine controllers found in VIA VT8500, WonderMedia WM8950 + and similar. These are listed as 1106:3106 rev. 0x84 on the + virtual PCI bus under vendor-provided kernels +- reg : Address and length of the io space +- interrupts : Should contain the controller interrupt line + +Examples: + +ethernet@d8004000 { + compatible = "via,vt8500-rhine"; + reg = <0xd8004000 0x100>; + interrupts = <10>; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt new file mode 100644 index 000000000000..5dbf169cd81c --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt @@ -0,0 +1,41 @@ +Broadcom BCM43xx Fullmac wireless SDIO devices + +This node provides properties for controlling the Broadcom wireless device. The +node is expected to be specified as a child node to the SDIO controller that +connects the device to the system. + +Required properties: + + - compatible : Should be "brcm,bcm4329-fmac". + +Optional properties: + - brcm,drive-strength : drive strength used for SDIO pins on device in mA + (default = 6). + - interrupt-parent : the phandle for the interrupt controller to which the + device interrupts are connected. + - interrupts : specifies attributes for the out-of-band interrupt (host-wake). + When not specified the device will use in-band SDIO interrupts. + - interrupt-names : name of the out-of-band interrupt, which must be set + to "host-wake". + +Example: + +mmc3: mmc@01c12000 { + #address-cells = <1>; + #size-cells = <0>; + + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins_a>; + vmmc-supply = <®_vmmc3>; + bus-width = <4>; + non-removable; + status = "okay"; + + brcmf: bcrmf@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <&pio>; + interrupts = <10 8>; /* PH10 / EINT10 */ + interrupt-names = "host-wake"; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt b/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt new file mode 100644 index 000000000000..189ae5cad8f7 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt @@ -0,0 +1,39 @@ +* Texas Instruments wl1251 wireless lan controller + +The wl1251 chip can be connected via SPI or via SDIO. This +document describes the binding for the SPI connected chip. + +Required properties: +- compatible : Should be "ti,wl1251" +- reg : Chip select address of device +- spi-max-frequency : Maximum SPI clocking speed of device in Hz +- interrupts : Should contain interrupt line +- interrupt-parent : Should be the phandle for the interrupt controller + that services interrupts for this device +- vio-supply : phandle to regulator providing VIO +- ti,power-gpio : GPIO connected to chip's PMEN pin + +Optional properties: +- ti,wl1251-has-eeprom : boolean, the wl1251 has an eeprom connected, which + provides configuration data (calibration, MAC, ...) +- Please consult Documentation/devicetree/bindings/spi/spi-bus.txt + for optional SPI connection related properties, + +Examples: + +&spi1 { + wl1251@0 { + compatible = "ti,wl1251"; + + reg = <0>; + spi-max-frequency = <48000000>; + spi-cpol; + spi-cpha; + + interrupt-parent = <&gpio2>; + interrupts = <10 IRQ_TYPE_NONE>; /* gpio line 42 */ + + vio-supply = <&vio>; + ti,power-gpio = <&gpio3 23 GPIO_ACTIVE_HIGH>; /* 87 */ + }; +}; diff --git a/Documentation/devicetree/bindings/nios2/nios2.txt b/Documentation/devicetree/bindings/nios2/nios2.txt new file mode 100644 index 000000000000..d6d0a94cb3bb --- /dev/null +++ b/Documentation/devicetree/bindings/nios2/nios2.txt @@ -0,0 +1,62 @@ +* Nios II Processor Binding + +This binding specifies what properties available in the device tree +representation of a Nios II Processor Core. + +Users can use sopc2dts tool for generating device tree sources (dts) from a +Qsys system. See more detail in: http://www.alterawiki.com/wiki/Sopc2dts + +Required properties: + +- compatible: Compatible property value should be "altr,nios2-1.0". +- reg: Contains CPU index. +- interrupt-controller: Specifies that the node is an interrupt controller +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt source, should be 1. +- clock-frequency: Contains the clock frequency for CPU, in Hz. +- dcache-line-size: Contains data cache line size. +- icache-line-size: Contains instruction line size. +- dcache-size: Contains data cache size. +- icache-size: Contains instruction cache size. +- altr,pid-num-bits: Specifies the number of bits to use to represent the process + identifier (PID). +- altr,tlb-num-ways: Specifies the number of set-associativity ways in the TLB. +- altr,tlb-num-entries: Specifies the number of entries in the TLB. +- altr,tlb-ptr-sz: Specifies size of TLB pointer. +- altr,has-mul: Specifies CPU hardware multipy support, should be 1. +- altr,has-mmu: Specifies CPU support MMU support, should be 1. +- altr,has-initda: Specifies CPU support initda instruction, should be 1. +- altr,reset-addr: Specifies CPU reset address +- altr,fast-tlb-miss-addr: Specifies CPU fast TLB miss exception address +- altr,exception-addr: Specifies CPU exception address + +Optional properties: +- altr,has-div: Specifies CPU hardware divide support +- altr,implementation: Nios II core implementation, this should be "fast"; + +Example: + +cpu@0x0 { + device_type = "cpu"; + compatible = "altr,nios2-1.0"; + reg = <0>; + interrupt-controller; + #interrupt-cells = <1>; + clock-frequency = <125000000>; + dcache-line-size = <32>; + icache-line-size = <32>; + dcache-size = <32768>; + icache-size = <32768>; + altr,implementation = "fast"; + altr,pid-num-bits = <8>; + altr,tlb-num-ways = <16>; + altr,tlb-num-entries = <128>; + altr,tlb-ptr-sz = <7>; + altr,has-div = <1>; + altr,has-mul = <1>; + altr,reset-addr = <0xc2800000>; + altr,fast-tlb-miss-addr = <0xc7fff400>; + altr,exception-addr = <0xd0000020>; + altr,has-initda = <1>; + altr,has-mmu = <1>; +}; diff --git a/Documentation/devicetree/bindings/nios2/timer.txt b/Documentation/devicetree/bindings/nios2/timer.txt new file mode 100644 index 000000000000..904a5846d7ac --- /dev/null +++ b/Documentation/devicetree/bindings/nios2/timer.txt @@ -0,0 +1,19 @@ +Altera Timer + +Required properties: + +- compatible : should be "altr,timer-1.0" +- reg : Specifies base physical address and size of the registers. +- interrupt-parent: phandle of the interrupt controller +- interrupts : Should contain the timer interrupt number +- clock-frequency : The frequency of the clock that drives the counter, in Hz. + +Example: + +timer { + compatible = "altr,timer-1.0"; + reg = <0x00400000 0x00000020>; + interrupt-parent = <&cpu>; + interrupts = <11>; + clock-frequency = <125000000>; +}; diff --git a/Documentation/devicetree/bindings/panel/auo,b101xtn01.txt b/Documentation/devicetree/bindings/panel/auo,b101xtn01.txt new file mode 100644 index 000000000000..889d511d66c9 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/auo,b101xtn01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 10.1" WXGA TFT LCD panel + +Required properties: +- compatible: should be "auo,b101xtn01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/panel/auo,b133htn01.txt b/Documentation/devicetree/bindings/panel/auo,b133htn01.txt new file mode 100644 index 000000000000..302226b5bb55 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/auo,b133htn01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 13.3" FHD (1920x1080) color TFT-LCD panel + +Required properties: +- compatible: should be "auo,b133htn01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/panel/auo,b133xtn01.txt b/Documentation/devicetree/bindings/panel/auo,b133xtn01.txt new file mode 100644 index 000000000000..7443b7c76769 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/auo,b133xtn01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 13.3" WXGA (1366x768) TFT LCD panel + +Required properties: +- compatible: should be "auo,b133xtn01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/panel/edt,et057090dhu.txt b/Documentation/devicetree/bindings/panel/edt,et057090dhu.txt new file mode 100644 index 000000000000..4903d7b1d947 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/edt,et057090dhu.txt @@ -0,0 +1,7 @@ +Emerging Display Technology Corp. 5.7" VGA TFT LCD panel + +Required properties: +- compatible: should be "edt,et057090dhu" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/panel/edt,et070080dh6.txt b/Documentation/devicetree/bindings/panel/edt,et070080dh6.txt new file mode 100644 index 000000000000..20cb38e836e4 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/edt,et070080dh6.txt @@ -0,0 +1,10 @@ +Emerging Display Technology Corp. ET070080DH6 7.0" WVGA TFT LCD panel + +Required properties: +- compatible: should be "edt,et070080dh6" + +This panel is the same as ETM0700G0DH6 except for the touchscreen. +ET070080DH6 is the model with resistive touch. + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/panel/edt,etm0700g0dh6.txt b/Documentation/devicetree/bindings/panel/edt,etm0700g0dh6.txt new file mode 100644 index 000000000000..ee4b18053e40 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/edt,etm0700g0dh6.txt @@ -0,0 +1,10 @@ +Emerging Display Technology Corp. ETM0700G0DH6 7.0" WVGA TFT LCD panel + +Required properties: +- compatible: should be "edt,etm0700g0dh6" + +This panel is the same as ET070080DH6 except for the touchscreen. +ETM0700G0DH6 is the model with capacitive multitouch. + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/panel/foxlink,fl500wvr00-a0t.txt b/Documentation/devicetree/bindings/panel/foxlink,fl500wvr00-a0t.txt new file mode 100644 index 000000000000..b47f9d87bc19 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/foxlink,fl500wvr00-a0t.txt @@ -0,0 +1,7 @@ +Foxlink Group 5" WVGA TFT LCD panel + +Required properties: +- compatible: should be "foxlink,fl500wvr00-a0t" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/panel/innolux,n116bge.txt b/Documentation/devicetree/bindings/panel/innolux,n116bge.txt new file mode 100644 index 000000000000..081bb939ed31 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/innolux,n116bge.txt @@ -0,0 +1,7 @@ +Innolux Corporation 11.6" WXGA (1366x768) TFT LCD panel + +Required properties: +- compatible: should be "innolux,n116bge" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/panel/innolux,n156bge-l21.txt b/Documentation/devicetree/bindings/panel/innolux,n156bge-l21.txt new file mode 100644 index 000000000000..7825844aafdf --- /dev/null +++ b/Documentation/devicetree/bindings/panel/innolux,n156bge-l21.txt @@ -0,0 +1,7 @@ +InnoLux 15.6" WXGA TFT LCD panel + +Required properties: +- compatible: should be "innolux,n156bge-l21" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/panel/lg,ld070wx3-sl01.txt b/Documentation/devicetree/bindings/panel/lg,ld070wx3-sl01.txt new file mode 100644 index 000000000000..5e649cb9aa1a --- /dev/null +++ b/Documentation/devicetree/bindings/panel/lg,ld070wx3-sl01.txt @@ -0,0 +1,7 @@ +LG Corporation 7" WXGA TFT LCD panel + +Required properties: +- compatible: should be "lg,ld070wx3-sl01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/panel/lg,lh500wx1-sd03.txt b/Documentation/devicetree/bindings/panel/lg,lh500wx1-sd03.txt new file mode 100644 index 000000000000..a04fd2b2e73d --- /dev/null +++ b/Documentation/devicetree/bindings/panel/lg,lh500wx1-sd03.txt @@ -0,0 +1,7 @@ +LG Corporation 5" HD TFT LCD panel + +Required properties: +- compatible: should be "lg,lh500wx1-sd03" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/panel/lg,lp129qe.txt b/Documentation/devicetree/bindings/panel/lg,lp129qe.txt new file mode 100644 index 000000000000..9f262e0c5a2e --- /dev/null +++ b/Documentation/devicetree/bindings/panel/lg,lp129qe.txt @@ -0,0 +1,7 @@ +LG 12.9" (2560x1700 pixels) TFT LCD panel + +Required properties: +- compatible: should be "lg,lp129qe" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/panel/samsung,ld9040.txt b/Documentation/devicetree/bindings/panel/samsung,ld9040.txt new file mode 100644 index 000000000000..07c36c3f7b52 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/samsung,ld9040.txt @@ -0,0 +1,66 @@ +Samsung LD9040 AMOLED LCD parallel RGB panel with SPI control bus + +Required properties: + - compatible: "samsung,ld9040" + - reg: address of the panel on SPI bus + - vdd3-supply: core voltage supply + - vci-supply: voltage supply for analog circuits + - reset-gpios: a GPIO spec for the reset pin + - display-timings: timings for the connected panel according to [1] + +The panel must obey rules for SPI slave device specified in document [2]. + +Optional properties: + - power-on-delay: delay after turning regulators on [ms] + - reset-delay: delay after reset sequence [ms] + - panel-width-mm: physical panel width [mm] + - panel-height-mm: physical panel height [mm] + +The device node can contain one 'port' child node with one child +'endpoint' node, according to the bindings defined in [3]. This +node should describe panel's video bus. + +[1]: Documentation/devicetree/bindings/video/display-timing.txt +[2]: Documentation/devicetree/bindings/spi/spi-bus.txt +[3]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + + lcd@0 { + compatible = "samsung,ld9040"; + reg = <0>; + vdd3-supply = <&ldo7_reg>; + vci-supply = <&ldo17_reg>; + reset-gpios = <&gpy4 5 0>; + spi-max-frequency = <1200000>; + spi-cpol; + spi-cpha; + power-on-delay = <10>; + reset-delay = <10>; + panel-width-mm = <90>; + panel-height-mm = <154>; + + display-timings { + timing { + clock-frequency = <23492370>; + hactive = <480>; + vactive = <800>; + hback-porch = <16>; + hfront-porch = <16>; + vback-porch = <2>; + vfront-porch = <28>; + hsync-len = <2>; + vsync-len = <1>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <0>; + pixelclk-active = <0>; + }; + }; + + port { + lcd_ep: endpoint { + remote-endpoint = <&fimd_dpi_ep>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/panel/samsung,s6e8aa0.txt b/Documentation/devicetree/bindings/panel/samsung,s6e8aa0.txt new file mode 100644 index 000000000000..e7ee988e3156 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/samsung,s6e8aa0.txt @@ -0,0 +1,56 @@ +Samsung S6E8AA0 AMOLED LCD 5.3 inch panel + +Required properties: + - compatible: "samsung,s6e8aa0" + - reg: the virtual channel number of a DSI peripheral + - vdd3-supply: core voltage supply + - vci-supply: voltage supply for analog circuits + - reset-gpios: a GPIO spec for the reset pin + - display-timings: timings for the connected panel as described by [1] + +Optional properties: + - power-on-delay: delay after turning regulators on [ms] + - reset-delay: delay after reset sequence [ms] + - init-delay: delay after initialization sequence [ms] + - panel-width-mm: physical panel width [mm] + - panel-height-mm: physical panel height [mm] + - flip-horizontal: boolean to flip image horizontally + - flip-vertical: boolean to flip image vertically + +The device node can contain one 'port' child node with one child +'endpoint' node, according to the bindings defined in [2]. This +node should describe panel's video bus. + +[1]: Documentation/devicetree/bindings/video/display-timing.txt +[2]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + + panel { + compatible = "samsung,s6e8aa0"; + reg = <0>; + vdd3-supply = <&vcclcd_reg>; + vci-supply = <&vlcd_reg>; + reset-gpios = <&gpy4 5 0>; + power-on-delay= <50>; + reset-delay = <100>; + init-delay = <100>; + panel-width-mm = <58>; + panel-height-mm = <103>; + flip-horizontal; + flip-vertical; + + display-timings { + timing0: timing-0 { + clock-frequency = <57153600>; + hactive = <720>; + vactive = <1280>; + hfront-porch = <5>; + hback-porch = <5>; + hsync-len = <5>; + vfront-porch = <13>; + vback-porch = <1>; + vsync-len = <2>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt index d6fae13ff062..9f4faa8e8d00 100644 --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -1,15 +1,11 @@ * Synopsys Designware PCIe interface Required properties: -- compatible: should contain "snps,dw-pcie" to identify the - core, plus an identifier for the specific instance, such - as "samsung,exynos5440-pcie" or "fsl,imx6q-pcie". -- reg: base addresses and lengths of the pcie controller, - the phy controller, additional register for the phy controller. -- interrupts: interrupt values for level interrupt, - pulse interrupt, special interrupt. -- clocks: from common clock binding: handle to pci clock. -- clock-names: from common clock binding: should be "pcie" and "pcie_bus". +- compatible: should contain "snps,dw-pcie" to identify the core. +- reg: Should contain the configuration address space. +- reg-names: Must be "config" for the PCIe configuration space. + (The old way of getting the configuration address space from "ranges" + is deprecated and should be avoided.) - #address-cells: set to <3> - #size-cells: set to <2> - device_type: set to "pci" @@ -19,65 +15,14 @@ Required properties: to define the mapping of the PCIe interface to interrupt numbers. - num-lanes: number of lanes to use +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - "pcie" + - "pcie_bus" Optional properties: - reset-gpio: gpio pin number of power good signal - -Optional properties for fsl,imx6q-pcie -- power-on-gpio: gpio pin number of power-enable signal -- wake-up-gpio: gpio pin number of incoming wakeup signal -- disable-gpio: gpio pin number of outgoing rfkill/endpoint disable signal - -Example: - -SoC specific DT Entry: - - pcie@290000 { - compatible = "samsung,exynos5440-pcie", "snps,dw-pcie"; - reg = <0x290000 0x1000 - 0x270000 0x1000 - 0x271000 0x40>; - interrupts = <0 20 0>, <0 21 0>, <0 22 0>; - clocks = <&clock 28>, <&clock 27>; - clock-names = "pcie", "pcie_bus"; - #address-cells = <3>; - #size-cells = <2>; - device_type = "pci"; - ranges = <0x00000800 0 0x40000000 0x40000000 0 0x00001000 /* configuration space */ - 0x81000000 0 0 0x40001000 0 0x00010000 /* downstream I/O */ - 0x82000000 0 0x40011000 0x40011000 0 0x1ffef000>; /* non-prefetchable memory */ - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0x0 0 &gic 53>; - num-lanes = <4>; - }; - - pcie@2a0000 { - compatible = "samsung,exynos5440-pcie", "snps,dw-pcie"; - reg = <0x2a0000 0x1000 - 0x272000 0x1000 - 0x271040 0x40>; - interrupts = <0 23 0>, <0 24 0>, <0 25 0>; - clocks = <&clock 29>, <&clock 27>; - clock-names = "pcie", "pcie_bus"; - #address-cells = <3>; - #size-cells = <2>; - device_type = "pci"; - ranges = <0x00000800 0 0x60000000 0x60000000 0 0x00001000 /* configuration space */ - 0x81000000 0 0 0x60001000 0 0x00010000 /* downstream I/O */ - 0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; /* non-prefetchable memory */ - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0x0 0 &gic 56>; - num-lanes = <4>; - }; - -Board specific DT Entry: - - pcie@290000 { - reset-gpio = <&pin_ctrl 5 0>; - }; - - pcie@2a0000 { - reset-gpio = <&pin_ctrl 22 0>; - }; +- bus-range: PCI bus numbers covered (it is recommended for new devicetrees to + specify this property, to keep backwards compatibility a range of 0x00-0xff + is assumed if not present) diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt new file mode 100644 index 000000000000..6fbba53a309b --- /dev/null +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -0,0 +1,40 @@ +* Freescale i.MX6 PCIe interface + +This PCIe host controller is based on the Synopsis Designware PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: +- compatible: "fsl,imx6q-pcie" +- reg: base addresse and length of the pcie controller +- interrupts: A list of interrupt outputs of the controller. Must contain an + entry for each entry in the interrupt-names property. +- interrupt-names: Must include the following entries: + - "msi": The interrupt that is asserted when an MSI is received +- clock-names: Must include the following additional entries: + - "pcie_phy" + +Example: + + pcie@0x01000000 { + compatible = "fsl,imx6q-pcie", "snps,dw-pcie"; + reg = <0x01ffc000 0x04000>, + <0x01f00000 0x80000>; + reg-names = "dbi", "config"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000 + 0x81000000 0 0 0x01f80000 0 0x00010000 + 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; + num-lanes = <1>; + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 2 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 3 &intc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 4 &intc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks 144>, <&clks 206>, <&clks 189>; + clock-names = "pcie", "pcie_bus", "pcie_phy"; + }; diff --git a/Documentation/devicetree/bindings/pci/fsl,pci.txt b/Documentation/devicetree/bindings/pci/fsl,pci.txt new file mode 100644 index 000000000000..d8ac4a768e7e --- /dev/null +++ b/Documentation/devicetree/bindings/pci/fsl,pci.txt @@ -0,0 +1,27 @@ +* Bus Enumeration by Freescale PCI-X Agent + +Typically any Freescale PCI-X bridge hardware strapped into Agent mode +is prevented from enumerating the bus. The PrPMC form-factor requires +all mezzanines to be PCI-X Agents, but one per system may still +enumerate the bus. + +The property defined below will allow a PCI-X bridge to be used for bus +enumeration despite being strapped into Agent mode. + +Required properties: +- fsl,pci-agent-force-enum : There is no value associated with this + property. The property itself is treated as a boolean. + +Example: + + /* PCI-X bridge known to be PrPMC Monarch */ + pci0: pci@ef008000 { + fsl,pci-agent-force-enum; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci"; + device_type = "pci"; + ... + ... + }; diff --git a/Documentation/devicetree/bindings/pci/host-generic-pci.txt b/Documentation/devicetree/bindings/pci/host-generic-pci.txt new file mode 100644 index 000000000000..cf3e205e0b7e --- /dev/null +++ b/Documentation/devicetree/bindings/pci/host-generic-pci.txt @@ -0,0 +1,100 @@ +* Generic PCI host controller + +Firmware-initialised PCI host controllers and PCI emulations, such as the +virtio-pci implementations found in kvmtool and other para-virtualised +systems, do not require driver support for complexities such as regulator +and clock management. In fact, the controller may not even require the +configuration of a control interface by the operating system, instead +presenting a set of fixed windows describing a subset of IO, Memory and +Configuration Spaces. + +Such a controller can be described purely in terms of the standardized device +tree bindings communicated in pci.txt: + + +Properties of the host controller node: + +- compatible : Must be "pci-host-cam-generic" or "pci-host-ecam-generic" + depending on the layout of configuration space (CAM vs + ECAM respectively). + +- device_type : Must be "pci". + +- ranges : As described in IEEE Std 1275-1994, but must provide + at least a definition of non-prefetchable memory. One + or both of prefetchable Memory and IO Space may also + be provided. + +- bus-range : Optional property (also described in IEEE Std 1275-1994) + to indicate the range of bus numbers for this controller. + If absent, defaults to <0 255> (i.e. all buses). + +- #address-cells : Must be 3. + +- #size-cells : Must be 2. + +- reg : The Configuration Space base address and size, as accessed + from the parent bus. + + +Properties of the /chosen node: + +- linux,pci-probe-only + : Optional property which takes a single-cell argument. + If '0', then Linux will assign devices in its usual manner, + otherwise it will not try to assign devices and instead use + them as they are configured already. + +Configuration Space is assumed to be memory-mapped (as opposed to being +accessed via an ioport) and laid out with a direct correspondence to the +geography of a PCI bus address by concatenating the various components to +form an offset. + +For CAM, this 24-bit offset is: + + cfg_offset(bus, device, function, register) = + bus << 16 | device << 11 | function << 8 | register + +Whilst ECAM extends this by 4 bits to accommodate 4k of function space: + + cfg_offset(bus, device, function, register) = + bus << 20 | device << 15 | function << 12 | register + +Interrupt mapping is exactly as described in `Open Firmware Recommended +Practice: Interrupt Mapping' and requires the following properties: + +- #interrupt-cells : Must be 1 + +- interrupt-map : <see aforementioned specification> + +- interrupt-map-mask : <see aforementioned specification> + + +Example: + +pci { + compatible = "pci-host-cam-generic" + device_type = "pci"; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x0 0x1>; + + // CPU_PHYSICAL(2) SIZE(2) + reg = <0x0 0x40000000 0x0 0x1000000>; + + // BUS_ADDRESS(3) CPU_PHYSICAL(2) SIZE(2) + ranges = <0x01000000 0x0 0x01000000 0x0 0x01000000 0x0 0x00010000>, + <0x02000000 0x0 0x41000000 0x0 0x41000000 0x0 0x3f000000>; + + + #interrupt-cells = <0x1>; + + // PCI_DEVICE(3) INT#(1) CONTROLLER(PHANDLE) CONTROLLER_DATA(3) + interrupt-map = < 0x0 0x0 0x0 0x1 &gic 0x0 0x4 0x1 + 0x800 0x0 0x0 0x1 &gic 0x0 0x5 0x1 + 0x1000 0x0 0x0 0x1 &gic 0x0 0x6 0x1 + 0x1800 0x0 0x0 0x1 &gic 0x0 0x7 0x1>; + + // PCI_DEVICE(3) INT#(1) + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; +} diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt index 24cee06915c9..d763e047c6ae 100644 --- a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt @@ -1,7 +1,10 @@ NVIDIA Tegra PCIe controller Required properties: -- compatible: "nvidia,tegra20-pcie" or "nvidia,tegra30-pcie" +- compatible: Must be one of: + - "nvidia,tegra20-pcie" + - "nvidia,tegra30-pcie" + - "nvidia,tegra124-pcie" - device_type: Must be "pci" - reg: A list of physical base address and length for each set of controller registers. Must contain an entry for each entry in the reg-names property. @@ -14,9 +17,6 @@ Required properties: - interrupt-names: Must include the following entries: "intr": The Tegra interrupt that is asserted for controller interrupts "msi": The Tegra interrupt that is asserted when an MSI is received -- pex-clk-supply: Supply voltage for internal reference clock -- vdd-supply: Power supply for controller (1.05V) -- avdd-supply: Power supply for controller (1.05V) (not required for Tegra20) - bus-range: Range of bus numbers associated with this controller - #address-cells: Address representation for root ports (must be 3) - cell 0 specifies the bus and device numbers of the root port: @@ -42,6 +42,10 @@ Required properties: - 0xc2000000: prefetchable memory region Please refer to the standard PCI bus binding document for a more detailed explanation. +- #interrupt-cells: Size representation for interrupts (must be 1) +- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties + Please refer to the standard PCI bus binding document for a more detailed + explanation. - clocks: Must contain an entry for each entry in clock-names. See ../clocks/clock-bindings.txt for details. - clock-names: Must include the following entries: @@ -56,6 +60,53 @@ Required properties: - afi - pcie_x +Required properties on Tegra124 and later: +- phys: Must contain an entry for each entry in phy-names. +- phy-names: Must include the following entries: + - pcie + +Power supplies for Tegra20: +- avdd-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V. +- vdd-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. +- avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must + supply 1.05 V. +- avdd-plle-supply: Power supply for PLLE, which is shared with SATA. Must + supply 1.05 V. +- vddio-pex-clk-supply: Power supply for PCIe clock. Must supply 3.3 V. + +Power supplies for Tegra30: +- Required: + - avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must + supply 1.05 V. + - avdd-plle-supply: Power supply for PLLE, which is shared with SATA. Must + supply 1.05 V. + - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must + supply 1.8 V. + - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks. + Must supply 3.3 V. +- Optional: + - If lanes 0 to 3 are used: + - avdd-pexa-supply: Power supply for analog PCIe logic. Must supply 1.05 V. + - vdd-pexa-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + - If lanes 4 or 5 are used: + - avdd-pexb-supply: Power supply for analog PCIe logic. Must supply 1.05 V. + - vdd-pexb-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + +Power supplies for Tegra124: +- Required: + - avddio-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V. + - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + - avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must + supply 1.05 V. + - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks. + Must supply 3.3 V. + - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3). + Must supply 3.3 V. + - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must + supply 2.8-3.3 V. + - avdd-pll-erefe-supply: Power supply for PLLE (shared with USB3). Must + supply 1.05 V. + Root ports are defined as subnodes of the PCIe controller node. Required properties: @@ -86,6 +137,10 @@ SoC DTSI: 0 99 0x04>; /* MSI interrupt */ interrupt-names = "intr", "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &intc GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + bus-range = <0x00 0xff>; #address-cells = <3>; #size-cells = <2>; diff --git a/Documentation/devicetree/bindings/pci/pci-keystone.txt b/Documentation/devicetree/bindings/pci/pci-keystone.txt new file mode 100644 index 000000000000..54eae2938174 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-keystone.txt @@ -0,0 +1,63 @@ +TI Keystone PCIe interface + +Keystone PCI host Controller is based on Designware PCI h/w version 3.65. +It shares common functions with PCIe Designware core driver and inherit +common properties defined in +Documentation/devicetree/bindings/pci/designware-pci.txt + +Please refer to Documentation/devicetree/bindings/pci/designware-pci.txt +for the details of Designware DT bindings. Additional properties are +described here as well as properties that are not applicable. + +Required Properties:- + +compatibility: "ti,keystone-pcie" +reg: index 1 is the base address and length of DW application registers. + index 2 is the base address and length of PCI device ID register. + +pcie_msi_intc : Interrupt controller device node for MSI IRQ chip + interrupt-cells: should be set to 1 + interrupt-parent: Parent interrupt controller phandle + interrupts: GIC interrupt lines connected to PCI MSI interrupt lines + + Example: + pcie_msi_intc: msi-interrupt-controller { + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 30 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 31 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 32 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 33 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 35 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 36 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 37 IRQ_TYPE_EDGE_RISING>; + }; + +pcie_intc: Interrupt controller device node for Legacy IRQ chip + interrupt-cells: should be set to 1 + interrupt-parent: Parent interrupt controller phandle + interrupts: GIC interrupt lines connected to PCI Legacy interrupt lines + + Example: + pcie_intc: legacy-interrupt-controller { + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 28 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 29 IRQ_TYPE_EDGE_RISING>; + }; + +Optional properties:- + phys: phandle to Generic Keystone SerDes phy for PCI + phy-names: name of the Generic Keystine SerDes phy for PCI + - If boot loader already does PCI link establishment, then phys and + phy-names shouldn't be present. + +Designware DT Properties not applicable for Keystone PCI + +1. pcie_bus clock-names not used. Instead, a phandle to phys is used. + diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt new file mode 100644 index 000000000000..d8ef5bf50f11 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt @@ -0,0 +1,66 @@ +Renesas AHB to PCI bridge +------------------------- + +This is the bridge used internally to connect the USB controllers to the +AHB. There is one bridge instance per USB port connected to the internal +OHCI and EHCI controllers. + +Required properties: +- compatible: "renesas,pci-r8a7790" for the R8A7790 SoC; + "renesas,pci-r8a7791" for the R8A7791 SoC. +- reg: A list of physical regions to access the device: the first is + the operational registers for the OHCI/EHCI controllers and the + second is for the bridge configuration and control registers. +- interrupts: interrupt for the device. +- clocks: The reference to the device clock. +- bus-range: The PCI bus number range; as this is a single bus, the range + should be specified as the same value twice. +- #address-cells: must be 3. +- #size-cells: must be 2. +- #interrupt-cells: must be 1. +- interrupt-map: standard property used to define the mapping of the PCI + interrupts to the GIC interrupts. +- interrupt-map-mask: standard property that helps to define the interrupt + mapping. + +Example SoC configuration: + + pci0: pci@ee090000 { + compatible = "renesas,pci-r8a7790"; + clocks = <&mstp7_clks R8A7790_CLK_EHCI>; + reg = <0x0 0xee090000 0x0 0xc00>, + <0x0 0xee080000 0x0 0x1100>; + interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + + bus-range = <0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + interrupt-map-mask = <0xff00 0 0 0x7>; + interrupt-map = <0x0000 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH + 0x0800 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH + 0x1000 0 0 2 &gic 0 108 IRQ_TYPE_LEVEL_HIGH>; + + pci@0,1 { + reg = <0x800 0 0 0 0>; + device_type = "pci"; + phys = <&usbphy 0 0>; + phy-names = "usb"; + }; + + pci@0,2 { + reg = <0x1000 0 0 0 0>; + device_type = "pci"; + phys = <&usbphy 0 0>; + phy-names = "usb"; + }; + }; + +Example board setup: + +&pci0 { + status = "okay"; + pinctrl-0 = <&usb0_pins>; + pinctrl-names = "default"; +}; diff --git a/Documentation/devicetree/bindings/pci/pci.txt b/Documentation/devicetree/bindings/pci/pci.txt index 41aeed38926d..f8fbe9af7b2f 100644 --- a/Documentation/devicetree/bindings/pci/pci.txt +++ b/Documentation/devicetree/bindings/pci/pci.txt @@ -7,3 +7,14 @@ And for the interrupt mapping part: Open Firmware Recommended Practice: Interrupt Mapping http://www.openfirmware.org/1275/practice/imap/imap0_9d.pdf + +Additionally to the properties specified in the above standards a host bridge +driver implementation may support the following properties: + +- linux,pci-domain: + If present this property assigns a fixed PCI domain number to a host bridge, + otherwise an unstable (across boots) unique number will be assigned. + It is required to either not set this property at all or set it for all + host bridges in the system, otherwise potentially conflicting domain numbers + may be assigned to root buses behind different host bridges. The domain + number for each host bridge in the system must be unique. diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt new file mode 100644 index 000000000000..29d3b989d3b0 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -0,0 +1,47 @@ +* Renesas RCar PCIe interface + +Required properties: +- compatible: should contain one of the following + "renesas,pcie-r8a7779", "renesas,pcie-r8a7790", "renesas,pcie-r8a7791" +- reg: base address and length of the pcie controller registers. +- #address-cells: set to <3> +- #size-cells: set to <2> +- bus-range: PCI bus numbers covered +- device_type: set to "pci" +- ranges: ranges for the PCI memory and I/O regions. +- dma-ranges: ranges for the inbound memory regions. +- interrupts: two interrupt sources for MSI interrupts, followed by interrupt + source for hardware related interrupts (e.g. link speed change). +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map: standard PCI properties + to define the mapping of the PCIe interface to interrupt + numbers. +- clocks: from common clock binding: clock specifiers for the PCIe controller + and PCIe bus clocks. +- clock-names: from common clock binding: should be "pcie" and "pcie_bus". + +Example: + +SoC specific DT Entry: + + pcie: pcie@fe000000 { + compatible = "renesas,pcie-r8a7791"; + reg = <0 0xfe000000 0 0x80000>; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x00 0xff>; + device_type = "pci"; + ranges = <0x01000000 0 0x00000000 0 0xfe100000 0 0x00100000 + 0x02000000 0 0xfe200000 0 0xfe200000 0 0x00200000 + 0x02000000 0 0x30000000 0 0x30000000 0 0x08000000 + 0x42000000 0 0x38000000 0 0x38000000 0 0x08000000>; + dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x40000000 + 0x42000000 2 0x00000000 2 0x00000000 0 0x40000000>; + interrupts = <0 116 4>, <0 117 4>, <0 118 4>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic 0 116 4>; + clocks = <&mstp3_clks R8A7791_CLK_PCIE>, <&pcie_bus_clk>; + clock-names = "pcie", "pcie_bus"; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt b/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt new file mode 100644 index 000000000000..4f9d23d2ed67 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt @@ -0,0 +1,65 @@ +* Samsung Exynos 5440 PCIe interface + +This PCIe host controller is based on the Synopsis Designware PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: +- compatible: "samsung,exynos5440-pcie" +- reg: base addresses and lengths of the pcie controller, + the phy controller, additional register for the phy controller. +- interrupts: A list of interrupt outputs for level interrupt, + pulse interrupt, special interrupt. + +Example: + +SoC specific DT Entry: + + pcie@290000 { + compatible = "samsung,exynos5440-pcie", "snps,dw-pcie"; + reg = <0x290000 0x1000 + 0x270000 0x1000 + 0x271000 0x40>; + interrupts = <0 20 0>, <0 21 0>, <0 22 0>; + clocks = <&clock 28>, <&clock 27>; + clock-names = "pcie", "pcie_bus"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x00000800 0 0x40000000 0x40000000 0 0x00001000 /* configuration space */ + 0x81000000 0 0 0x40001000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x40011000 0x40011000 0 0x1ffef000>; /* non-prefetchable memory */ + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; + num-lanes = <4>; + }; + + pcie@2a0000 { + compatible = "samsung,exynos5440-pcie", "snps,dw-pcie"; + reg = <0x2a0000 0x1000 + 0x272000 0x1000 + 0x271040 0x40>; + interrupts = <0 23 0>, <0 24 0>, <0 25 0>; + clocks = <&clock 29>, <&clock 27>; + clock-names = "pcie", "pcie_bus"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x00000800 0 0x60000000 0x60000000 0 0x00001000 /* configuration space */ + 0x81000000 0 0 0x60001000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; /* non-prefetchable memory */ + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; + num-lanes = <4>; + }; + +Board specific DT Entry: + + pcie@290000 { + reset-gpio = <&pin_ctrl 5 0>; + }; + + pcie@2a0000 { + reset-gpio = <&pin_ctrl 22 0>; + }; diff --git a/Documentation/devicetree/bindings/pci/spear13xx-pcie.txt b/Documentation/devicetree/bindings/pci/spear13xx-pcie.txt new file mode 100644 index 000000000000..49ea76da7718 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/spear13xx-pcie.txt @@ -0,0 +1,14 @@ +SPEAr13XX PCIe DT detail: +================================ + +SPEAr13XX uses synopsis designware PCIe controller and ST MiPHY as phy +controller. + +Required properties: +- compatible : should be "st,spear1340-pcie", "snps,dw-pcie". +- phys : phandle to phy node associated with pcie controller +- phy-names : must be "pcie-phy" +- All other definitions as per generic PCI bindings + + Optional properties: +- st,pcie-is-gen1 indicates that forced gen1 initialization is needed. diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt new file mode 100644 index 000000000000..3d217911b313 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/ti-pci.txt @@ -0,0 +1,59 @@ +TI PCI Controllers + +PCIe Designware Controller + - compatible: Should be "ti,dra7-pcie"" + - reg : Two register ranges as listed in the reg-names property + - reg-names : The first entry must be "ti-conf" for the TI specific registers + The second entry must be "rc-dbics" for the designware pcie + registers + The third entry must be "config" for the PCIe configuration space + - phys : list of PHY specifiers (used by generic PHY framework) + - phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the + number of PHYs as specified in *phys* property. + - ti,hwmods : Name of the hwmod associated to the pcie, "pcie<X>", + where <X> is the instance number of the pcie from the HW spec. + - interrupts : Two interrupt entries must be specified. The first one is for + main interrupt line and the second for MSI interrupt line. + - #address-cells, + #size-cells, + #interrupt-cells, + device_type, + ranges, + num-lanes, + interrupt-map-mask, + interrupt-map : as specified in ../designware-pcie.txt + +Example: +axi { + compatible = "simple-bus"; + #size-cells = <1>; + #address-cells = <1>; + ranges = <0x51000000 0x51000000 0x3000 + 0x0 0x20000000 0x10000000>; + pcie@51000000 { + compatible = "ti,dra7-pcie"; + reg = <0x51000000 0x2000>, <0x51002000 0x14c>, <0x1000 0x2000>; + reg-names = "rc_dbics", "ti_conf", "config"; + interrupts = <0 232 0x4>, <0 233 0x4>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0 0x03000 0 0x00010000 + 0x82000000 0 0x20013000 0x13000 0 0xffed000>; + #interrupt-cells = <1>; + num-lanes = <1>; + ti,hwmods = "pcie1"; + phys = <&pcie1_phy>; + phy-names = "pcie-phy0"; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc 1>, + <0 0 0 2 &pcie_intc 2>, + <0 0 0 3 &pcie_intc 3>, + <0 0 0 4 &pcie_intc 4>; + pcie_intc: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/pci/xgene-pci.txt b/Documentation/devicetree/bindings/pci/xgene-pci.txt new file mode 100644 index 000000000000..1070b068c7c6 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/xgene-pci.txt @@ -0,0 +1,57 @@ +* AppliedMicro X-Gene PCIe interface + +Required properties: +- device_type: set to "pci" +- compatible: should contain "apm,xgene-pcie" to identify the core. +- reg: A list of physical base address and length for each set of controller + registers. Must contain an entry for each entry in the reg-names + property. +- reg-names: Must include the following entries: + "csr": controller configuration registers. + "cfg": pcie configuration space registers. +- #address-cells: set to <3> +- #size-cells: set to <2> +- ranges: ranges for the outbound memory, I/O regions. +- dma-ranges: ranges for the inbound memory regions. +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map: standard PCI properties + to define the mapping of the PCIe interface to interrupt + numbers. +- clocks: from common clock binding: handle to pci clock. + +Optional properties: +- status: Either "ok" or "disabled". +- dma-coherent: Present if dma operations are coherent + +Example: + +SoC specific DT Entry: + + pcie0: pcie@1f2b0000 { + status = "disabled"; + device_type = "pci"; + compatible = "apm,xgene-storm-pcie", "apm,xgene-pcie"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = < 0x00 0x1f2b0000 0x0 0x00010000 /* Controller registers */ + 0xe0 0xd0000000 0x0 0x00040000>; /* PCI config space */ + reg-names = "csr", "cfg"; + ranges = <0x01000000 0x00 0x00000000 0xe0 0x10000000 0x00 0x00010000 /* io */ + 0x02000000 0x00 0x80000000 0xe1 0x80000000 0x00 0x80000000>; /* mem */ + dma-ranges = <0x42000000 0x80 0x00000000 0x80 0x00000000 0x00 0x80000000 + 0x42000000 0x00 0x00000000 0x00 0x00000000 0x80 0x00000000>; + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xc2 0x1 + 0x0 0x0 0x0 0x2 &gic 0x0 0xc3 0x1 + 0x0 0x0 0x0 0x3 &gic 0x0 0xc4 0x1 + 0x0 0x0 0x0 0x4 &gic 0x0 0xc5 0x1>; + dma-coherent; + clocks = <&pcie0clk 0>; + }; + + +Board specific DT Entry: + &pcie0 { + status = "ok"; + }; diff --git a/Documentation/devicetree/bindings/pci/xilinx-pcie.txt b/Documentation/devicetree/bindings/pci/xilinx-pcie.txt new file mode 100644 index 000000000000..3e2c88d97ad4 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/xilinx-pcie.txt @@ -0,0 +1,62 @@ +* Xilinx AXI PCIe Root Port Bridge DT description + +Required properties: +- #address-cells: Address representation for root ports, set to <3> +- #size-cells: Size representation for root ports, set to <2> +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- compatible: Should contain "xlnx,axi-pcie-host-1.00.a" +- reg: Should contain AXI PCIe registers location and length +- device_type: must be "pci" +- interrupts: Should contain AXI PCIe interrupt +- interrupt-map-mask, + interrupt-map: standard PCI properties to define the mapping of the + PCI interface to interrupt numbers. +- ranges: ranges for the PCI memory regions (I/O space region is not + supported by hardware) + Please refer to the standard PCI bus binding document for a more + detailed explanation + +Optional properties: +- bus-range: PCI bus numbers covered + +Interrupt controller child node ++++++++++++++++++++++++++++++++ +Required properties: +- interrupt-controller: identifies the node as an interrupt controller +- #address-cells: specifies the number of cells needed to encode an + address. The value must be 0. +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. + +NOTE: +The core provides a single interrupt for both INTx/MSI messages. So, +created a interrupt controller node to support 'interrupt-map' DT +functionality. The driver will create an IRQ domain for this map, decode +the four INTx interrupts in ISR and route them to this domain. + + +Example: +++++++++ + + pci_express: axi-pcie@50000000 { + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + compatible = "xlnx,axi-pcie-host-1.00.a"; + reg = < 0x50000000 0x10000000 >; + device_type = "pci"; + interrupts = < 0 52 4 >; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc 1>, + <0 0 0 2 &pcie_intc 2>, + <0 0 0 3 &pcie_intc 3>, + <0 0 0 4 &pcie_intc 4>; + ranges = < 0x02000000 0 0x60000000 0x60000000 0 0x10000000 >; + + pcie_intc: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + } + }; diff --git a/Documentation/devicetree/bindings/phy/apm-xgene-phy.txt b/Documentation/devicetree/bindings/phy/apm-xgene-phy.txt new file mode 100644 index 000000000000..5f3a65a9dd88 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/apm-xgene-phy.txt @@ -0,0 +1,79 @@ +* APM X-Gene 15Gbps Multi-purpose PHY nodes + +PHY nodes are defined to describe on-chip 15Gbps Multi-purpose PHY. Each +PHY (pair of lanes) has its own node. + +Required properties: +- compatible : Shall be "apm,xgene-phy". +- reg : PHY memory resource is the SDS PHY access resource. +- #phy-cells : Shall be 1 as it expects one argument for setting + the mode of the PHY. Possible values are 0 (SATA), + 1 (SGMII), 2 (PCIe), 3 (USB), and 4 (XFI). + +Optional properties: +- status : Shall be "ok" if enabled or "disabled" if disabled. + Default is "ok". +- clocks : Reference to the clock entry. +- apm,tx-eye-tuning : Manual control to fine tune the capture of the serial + bit lines from the automatic calibrated position. + Two set of 3-tuple setting for each (up to 3) + supported link speed on the host. Range from 0 to + 127 in unit of one bit period. Default is 10. +- apm,tx-eye-direction : Eye tuning manual control direction. 0 means sample + data earlier than the nominal sampling point. 1 means + sample data later than the nominal sampling point. + Two set of 3-tuple setting for each (up to 3) + supported link speed on the host. Default is 0. +- apm,tx-boost-gain : Frequency boost AC (LSB 3-bit) and DC (2-bit) + gain control. Two set of 3-tuple setting for each + (up to 3) supported link speed on the host. Range is + between 0 to 31 in unit of dB. Default is 3. +- apm,tx-amplitude : Amplitude control. Two set of 3-tuple setting for + each (up to 3) supported link speed on the host. + Range is between 0 to 199500 in unit of uV. + Default is 199500 uV. +- apm,tx-pre-cursor1 : 1st pre-cursor emphasis taps control. Two set of + 3-tuple setting for each (up to 3) supported link + speed on the host. Range is 0 to 273000 in unit of + uV. Default is 0. +- apm,tx-pre-cursor2 : 2st pre-cursor emphasis taps control. Two set of + 3-tuple setting for each (up to 3) supported link + speed on the host. Range is 0 to 127400 in unit uV. + Default is 0x0. +- apm,tx-post-cursor : Post-cursor emphasis taps control. Two set of + 3-tuple setting for Gen1, Gen2, and Gen3. Range is + between 0 to 0x1f in unit of 18.2mV. Default is 0xf. +- apm,tx-speed : Tx operating speed. One set of 3-tuple for each + supported link speed on the host. + 0 = 1-2Gbps + 1 = 2-4Gbps (1st tuple default) + 2 = 4-8Gbps + 3 = 8-15Gbps (2nd tuple default) + 4 = 2.5-4Gbps + 5 = 4-5Gbps + 6 = 5-6Gbps + 7 = 6-16Gbps (3rd tuple default) + +NOTE: PHY override parameters are board specific setting. + +Example: + phy1: phy@1f21a000 { + compatible = "apm,xgene-phy"; + reg = <0x0 0x1f21a000 0x0 0x100>; + #phy-cells = <1>; + status = "disabled"; + }; + + phy2: phy@1f22a000 { + compatible = "apm,xgene-phy"; + reg = <0x0 0x1f22a000 0x0 0x100>; + #phy-cells = <1>; + status = "ok"; + }; + + phy3: phy@1f23a000 { + compatible = "apm,xgene-phy"; + reg = <0x0 0x1f23a000 0x0 0x100>; + #phy-cells = <1>; + status = "ok"; + }; diff --git a/Documentation/devicetree/bindings/phy/berlin-sata-phy.txt b/Documentation/devicetree/bindings/phy/berlin-sata-phy.txt new file mode 100644 index 000000000000..88f8c23384c0 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/berlin-sata-phy.txt @@ -0,0 +1,34 @@ +Berlin SATA PHY +--------------- + +Required properties: +- compatible: should be "marvell,berlin2q-sata-phy" +- address-cells: should be 1 +- size-cells: should be 0 +- phy-cells: from the generic PHY bindings, must be 1 +- reg: address and length of the register +- clocks: reference to the clock entry + +Sub-nodes: +Each PHY should be represented as a sub-node. + +Sub-nodes required properties: +- reg: the PHY number + +Example: + sata_phy: phy@f7e900a0 { + compatible = "marvell,berlin2q-sata-phy"; + reg = <0xf7e900a0 0x200>; + clocks = <&chip CLKID_SATA>; + #address-cells = <1>; + #size-cells = <0>; + #phy-cells = <1>; + + sata-phy@0 { + reg = <0>; + }; + + sata-phy@1 { + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/hix5hd2-phy.txt b/Documentation/devicetree/bindings/phy/hix5hd2-phy.txt new file mode 100644 index 000000000000..296168b74d24 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/hix5hd2-phy.txt @@ -0,0 +1,22 @@ +Hisilicon hix5hd2 SATA PHY +----------------------- + +Required properties: +- compatible: should be "hisilicon,hix5hd2-sata-phy" +- reg: offset and length of the PHY registers +- #phy-cells: must be 0 +Refer to phy/phy-bindings.txt for the generic PHY binding properties + +Optional Properties: +- hisilicon,peripheral-syscon: phandle of syscon used to control peripheral. +- hisilicon,power-reg: offset and bit number within peripheral-syscon, + register of controlling sata power supply. + +Example: + sata_phy: phy@f9900000 { + compatible = "hisilicon,hix5hd2-sata-phy"; + reg = <0xf9900000 0x10000>; + #phy-cells = <0>; + hisilicon,peripheral-syscon = <&peripheral_ctrl>; + hisilicon,power-reg = <0x8 10>; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-bindings.txt b/Documentation/devicetree/bindings/phy/phy-bindings.txt index 8ae844fc0c60..1293c321754c 100644 --- a/Documentation/devicetree/bindings/phy/phy-bindings.txt +++ b/Documentation/devicetree/bindings/phy/phy-bindings.txt @@ -10,6 +10,10 @@ Required Properties: provider can use the values in cells to find the appropriate PHY. +Optional Properties: +phy-supply: Phandle to a regulator that provides power to the PHY. This + regulator will be managed during the PHY power on/off sequence. + For example: phys: phy { @@ -23,7 +27,7 @@ phys: phy { }; That node describes an IP block (PHY provider) that implements 2 different PHYs. -In order to differentiate between these 2 PHYs, an additonal specifier should be +In order to differentiate between these 2 PHYs, an additional specifier should be given while trying to get a reference to it. PHY user node diff --git a/Documentation/devicetree/bindings/phy/phy-miphy365x.txt b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt new file mode 100644 index 000000000000..42c880886cf7 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt @@ -0,0 +1,76 @@ +STMicroelectronics STi MIPHY365x PHY binding +============================================ + +This binding describes a miphy device that is used to control PHY hardware +for SATA and PCIe. + +Required properties (controller (parent) node): +- compatible : Should be "st,miphy365x-phy" +- st,syscfg : Should be a phandle of the system configuration register group + which contain the SATA, PCIe mode setting bits + +Required nodes : A sub-node is required for each channel the controller + provides. Address range information including the usual + 'reg' and 'reg-names' properties are used inside these + nodes to describe the controller's topology. These nodes + are translated by the driver's .xlate() function. + +Required properties (port (child) node): +- #phy-cells : Should be 1 (See second example) + Cell after port phandle is device type from: + - MIPHY_TYPE_SATA + - MIPHY_TYPE_PCI +- reg : Address and length of register sets for each device in + "reg-names" +- reg-names : The names of the register addresses corresponding to the + registers filled in "reg": + - sata: For SATA devices + - pcie: For PCIe devices + - syscfg: To specify the syscfg based config register + +Optional properties (port (child) node): +- st,sata-gen : Generation of locally attached SATA IP. Expected values + are {1,2,3). If not supplied generation 1 hardware will + be expected +- st,pcie-tx-pol-inv : Bool property to invert the polarity PCIe Tx (Txn/Txp) +- st,sata-tx-pol-inv : Bool property to invert the polarity SATA Tx (Txn/Txp) + +Example: + + miphy365x_phy: miphy365x@fe382000 { + compatible = "st,miphy365x-phy"; + st,syscfg = <&syscfg_rear>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + phy_port0: port@fe382000 { + reg = <0xfe382000 0x100>, <0xfe394000 0x100>, <0x824 0x4>; + reg-names = "sata", "pcie", "syscfg"; + #phy-cells = <1>; + st,sata-gen = <3>; + }; + + phy_port1: port@fe38a000 { + reg = <0xfe38a000 0x100>, <0xfe804000 0x100>, <0x828 0x4>;; + reg-names = "sata", "pcie", "syscfg"; + #phy-cells = <1>; + st,pcie-tx-pol-inv; + }; + }; + +Specifying phy control of devices +================================= + +Device nodes should specify the configuration required in their "phys" +property, containing a phandle to the phy port node and a device type. + +Example: + +#include <dt-bindings/phy/phy-miphy365x.h> + + sata0: sata@fe380000 { + ... + phys = <&phy_port0 MIPHY_TYPE_SATA>; + ... + }; diff --git a/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt new file mode 100644 index 000000000000..1ef8228db73b --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt @@ -0,0 +1,30 @@ +ST STiH407 USB PHY controller + +This file documents the dt bindings for the usb picoPHY driver which is the PHY for both USB2 and USB3 +host controllers (when controlling usb2/1.1 devices) available on STiH407 SoC family from STMicroelectronics. + +Required properties: +- compatible : should be "st,stih407-usb2-phy" +- reg : contain the offset and length of the system configuration registers + used as glue logic to control & parameter phy +- reg-names : the names of the system configuration registers in "reg", should be "param" and "reg" +- st,syscfg : sysconfig register to manage phy parameter at driver level +- resets : list of phandle and reset specifier pairs. There should be two entries, one + for the whole phy and one for the port +- reset-names : list of reset signal names. Should be "global" and "port" +See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt +See: Documentation/devicetree/bindings/reset/reset.txt + +Example: + +usb2_picophy0: usbpicophy@f8 { + compatible = "st,stih407-usb2-phy"; + reg = <0xf8 0x04>, /* syscfg 5062 */ + <0xf4 0x04>; /* syscfg 5061 */ + reg-names = "param", "ctrl"; + #phy-cells = <0>; + st,syscfg = <&syscfg_core>; + resets = <&softreset STIH407_PICOPHY_SOFTRESET>, + <&picophyreset STIH407_PICOPHY0_RESET>; + reset-names = "global", "port"; +}; diff --git a/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt b/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt new file mode 100644 index 000000000000..00944a05ee6b --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt @@ -0,0 +1,24 @@ +STMicroelectronics STiH41x USB PHY binding +------------------------------------------ + +This file contains documentation for the usb phy found in STiH415/6 SoCs from +STMicroelectronics. + +Required properties: +- compatible : should be "st,stih416-usb-phy" or "st,stih415-usb-phy" +- st,syscfg : should be a phandle of the syscfg node +- clock-names : must contain "osc_phy" +- clocks : must contain an entry for each name in clock-names. +See: Documentation/devicetree/bindings/clock/clock-bindings.txt +- #phy-cells : must be 0 for this phy +See: Documentation/devicetree/bindings/phy/phy-bindings.txt + +Example: + +usb2_phy: usb2phy@0 { + compatible = "st,stih416-usb-phy"; + #phy-cell = <0>; + st,syscfg = <&syscfg_rear>; + clocks = <&clk_sysin>; + clock-names = "osc_phy"; +}; diff --git a/Documentation/devicetree/bindings/phy/qcom-apq8064-sata-phy.txt b/Documentation/devicetree/bindings/phy/qcom-apq8064-sata-phy.txt new file mode 100644 index 000000000000..952f6c96bab9 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom-apq8064-sata-phy.txt @@ -0,0 +1,24 @@ +Qualcomm APQ8064 SATA PHY Controller +------------------------------------ + +SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers. +Each SATA PHY controller should have its own node. + +Required properties: +- compatible: compatible list, contains "qcom,apq8064-sata-phy". +- reg: offset and length of the SATA PHY register set; +- #phy-cells: must be zero +- clocks: a list of phandles and clock-specifier pairs, one for each entry in + clock-names. +- clock-names: must be "cfg" for phy config clock. + +Example: + sata_phy: sata-phy@1b400000 { + compatible = "qcom,apq8064-sata-phy"; + reg = <0x1b400000 0x200>; + + clocks = <&gcc SATA_PHY_CFG_CLK>; + clock-names = "cfg"; + + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt b/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt new file mode 100644 index 000000000000..86f2dbe07ed4 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt @@ -0,0 +1,39 @@ +Qualcomm DWC3 HS AND SS PHY CONTROLLER +-------------------------------------- + +DWC3 PHY nodes are defined to describe on-chip Synopsis Physical layer +controllers. Each DWC3 PHY controller should have its own node. + +Required properties: +- compatible: should contain one of the following: + - "qcom,dwc3-hs-usb-phy" for High Speed Synopsis PHY controller + - "qcom,dwc3-ss-usb-phy" for Super Speed Synopsis PHY controller +- reg: offset and length of the DWC3 PHY controller register set +- #phy-cells: must be zero +- clocks: a list of phandles and clock-specifier pairs, one for each entry in + clock-names. +- clock-names: Should contain "ref" for the PHY reference clock + +Optional clocks: + "xo" External reference clock + +Example: + phy@100f8800 { + compatible = "qcom,dwc3-hs-usb-phy"; + reg = <0x100f8800 0x30>; + clocks = <&gcc USB30_0_UTMI_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "ok"; + }; + + phy@100f8830 { + compatible = "qcom,dwc3-ss-usb-phy"; + reg = <0x100f8830 0x30>; + clocks = <&gcc USB30_0_MASTER_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "ok"; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom-ipq806x-sata-phy.txt b/Documentation/devicetree/bindings/phy/qcom-ipq806x-sata-phy.txt new file mode 100644 index 000000000000..76bfbd056202 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom-ipq806x-sata-phy.txt @@ -0,0 +1,23 @@ +Qualcomm IPQ806x SATA PHY Controller +------------------------------------ + +SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers. +Each SATA PHY controller should have its own node. + +Required properties: +- compatible: compatible list, contains "qcom,ipq806x-sata-phy" +- reg: offset and length of the SATA PHY register set; +- #phy-cells: must be zero +- clocks: must be exactly one entry +- clock-names: must be "cfg" + +Example: + sata_phy: sata-phy@1b400000 { + compatible = "qcom,ipq806x-sata-phy"; + reg = <0x1b400000 0x200>; + + clocks = <&gcc SATA_PHY_CFG_CLK>; + clock-names = "cfg"; + + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt b/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt new file mode 100644 index 000000000000..00fc52a034b7 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt @@ -0,0 +1,51 @@ +* Renesas R-Car generation 2 USB PHY + +This file provides information on what the device node for the R-Car generation +2 USB PHY contains. + +Required properties: +- compatible: "renesas,usb-phy-r8a7790" if the device is a part of R8A7790 SoC. + "renesas,usb-phy-r8a7791" if the device is a part of R8A7791 SoC. +- reg: offset and length of the register block. +- #address-cells: number of address cells for the USB channel subnodes, must + be <1>. +- #size-cells: number of size cells for the USB channel subnodes, must be <0>. +- clocks: clock phandle and specifier pair. +- clock-names: string, clock input name, must be "usbhs". + +The USB PHY device tree node should have the subnodes corresponding to the USB +channels. These subnodes must contain the following properties: +- reg: the USB controller selector; see the table below for the values. +- #phy-cells: see phy-bindings.txt in the same directory, must be <1>. + +The phandle's argument in the PHY specifier is the USB controller selector for +the USB channel; see the selector meanings below: + ++-----------+---------------+---------------+ +|\ Selector | | | ++ --------- + 0 | 1 | +| Channel \| | | ++-----------+---------------+---------------+ +| 0 | PCI EHCI/OHCI | HS-USB | +| 2 | PCI EHCI/OHCI | xHCI | ++-----------+---------------+---------------+ + +Example (Lager board): + + usb-phy@e6590100 { + compatible = "renesas,usb-phy-r8a7790"; + reg = <0 0xe6590100 0 0x100>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&mstp7_clks R8A7790_CLK_HSUSB>; + clock-names = "usbhs"; + + usb-channel@0 { + reg = <0>; + #phy-cells = <1>; + }; + usb-channel@2 { + reg = <2>; + #phy-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt index c0fccaa1671e..15e0f2c7130f 100644 --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt @@ -17,6 +17,153 @@ Samsung EXYNOS SoC series Display Port PHY ------------------------------------------------- Required properties: -- compatible : should be "samsung,exynos5250-dp-video-phy"; -- reg : offset and length of the Display Port PHY register set; +- compatible : should be one of the following supported values: + - "samsung,exynos5250-dp-video-phy" + - "samsung,exynos5420-dp-video-phy" +- samsung,pmu-syscon: phandle for PMU system controller interface, used to + control pmu registers for power isolation. - #phy-cells : from the generic PHY bindings, must be 0; + +Samsung S5P/EXYNOS SoC series USB PHY +------------------------------------------------- + +Required properties: +- compatible : should be one of the listed compatibles: + - "samsung,exynos3250-usb2-phy" + - "samsung,exynos4210-usb2-phy" + - "samsung,exynos4x12-usb2-phy" + - "samsung,exynos5250-usb2-phy" + - "samsung,s5pv210-usb2-phy" +- reg : a list of registers used by phy driver + - first and obligatory is the location of phy modules registers +- samsung,sysreg-phandle - handle to syscon used to control the system registers +- samsung,pmureg-phandle - handle to syscon used to control PMU registers +- #phy-cells : from the generic phy bindings, must be 1; +- clocks and clock-names: + - the "phy" clock is required by the phy module, used as a gate + - the "ref" clock is used to get the rate of the clock provided to the + PHY module + +The first phandle argument in the PHY specifier identifies the PHY, its +meaning is compatible dependent. For the currently supported SoCs (Exynos 4210 +and Exynos 4212) it is as follows: + 0 - USB device ("device"), + 1 - USB host ("host"), + 2 - HSIC0 ("hsic0"), + 3 - HSIC1 ("hsic1"), +Exynos3250 has only USB device phy available as phy 0. + +Exynos 4210 and Exynos 4212 use mode switching and require that mode switch +register is supplied. + +Example: + +For Exynos 4412 (compatible with Exynos 4212): + +usbphy: phy@125b0000 { + compatible = "samsung,exynos4x12-usb2-phy"; + reg = <0x125b0000 0x100>; + clocks = <&clock 305>, <&clock 2>; + clock-names = "phy", "ref"; + status = "okay"; + #phy-cells = <1>; + samsung,sysreg-phandle = <&sys_reg>; + samsung,pmureg-phandle = <&pmu_reg>; +}; + +Then the PHY can be used in other nodes such as: + +phy-consumer@12340000 { + phys = <&usbphy 2>; + phy-names = "phy"; +}; + +Refer to DT bindings documentation of particular PHY consumer devices for more +information about required PHYs and the way of specification. + +Samsung SATA PHY Controller +--------------------------- + +SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers. +Each SATA PHY controller should have its own node. + +Required properties: +- compatible : compatible list, contains "samsung,exynos5250-sata-phy" +- reg : offset and length of the SATA PHY register set; +- #phy-cells : must be zero +- clocks : must be exactly one entry +- clock-names : must be "sata_phyctrl" +- samsung,exynos-sataphy-i2c-phandle : a phandle to the I2C device, no arguments +- samsung,syscon-phandle : a phandle to the PMU system controller, no arguments + +Example: + sata_phy: sata-phy@12170000 { + compatible = "samsung,exynos5250-sata-phy"; + reg = <0x12170000 0x1ff>; + clocks = <&clock 287>; + clock-names = "sata_phyctrl"; + #phy-cells = <0>; + samsung,exynos-sataphy-i2c-phandle = <&sata_phy_i2c>; + samsung,syscon-phandle = <&pmu_syscon>; + }; + +Device-Tree bindings for sataphy i2c client driver +-------------------------------------------------- + +Required properties: +compatible: Should be "samsung,exynos-sataphy-i2c" +- reg: I2C address of the sataphy i2c device. + +Example: + + sata_phy_i2c:sata-phy@38 { + compatible = "samsung,exynos-sataphy-i2c"; + reg = <0x38>; + }; + +Samsung Exynos5 SoC series USB DRD PHY controller +-------------------------------------------------- + +Required properties: +- compatible : Should be set to one of the following supported values: + - "samsung,exynos5250-usbdrd-phy" - for exynos5250 SoC, + - "samsung,exynos5420-usbdrd-phy" - for exynos5420 SoC. +- reg : Register offset and length of USB DRD PHY register set; +- clocks: Clock IDs array as required by the controller +- clock-names: names of clocks correseponding to IDs in the clock property; + Required clocks: + - phy: main PHY clock (same as USB DRD controller i.e. DWC3 IP clock), + used for register access. + - ref: PHY's reference clock (usually crystal clock), used for + PHY operations, associated by phy name. It is used to + determine bit values for clock settings register. + For Exynos5420 this is given as 'sclk_usbphy30' in CMU. +- samsung,pmu-syscon: phandle for PMU system controller interface, used to + control pmu registers for power isolation. +- #phy-cells : from the generic PHY bindings, must be 1; + +For "samsung,exynos5250-usbdrd-phy" and "samsung,exynos5420-usbdrd-phy" +compatible PHYs, the second cell in the PHY specifier identifies the +PHY id, which is interpreted as follows: + 0 - UTMI+ type phy, + 1 - PIPE3 type phy, + +Example: + usbdrd_phy: usbphy@12100000 { + compatible = "samsung,exynos5250-usbdrd-phy"; + reg = <0x12100000 0x100>; + clocks = <&clock 286>, <&clock 1>; + clock-names = "phy", "ref"; + samsung,pmu-syscon = <&pmu_system_controller>; + #phy-cells = <1>; + }; + +- aliases: For SoCs like Exynos5420 having multiple USB 3.0 DRD PHY controllers, + 'usbdrd_phy' nodes should have numbered alias in the aliases node, + in the form of usbdrdphyN, N = 0, 1... (depending on number of + controllers). +Example: + aliases { + usbdrdphy0 = &usb3_phy0; + usbdrdphy1 = &usb3_phy1; + }; diff --git a/Documentation/devicetree/bindings/phy/st-spear-miphy.txt b/Documentation/devicetree/bindings/phy/st-spear-miphy.txt new file mode 100644 index 000000000000..2a6bfdcc09b3 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/st-spear-miphy.txt @@ -0,0 +1,15 @@ +ST SPEAr miphy DT details +========================= + +ST Microelectronics SPEAr miphy is a phy controller supporting PCIe and SATA. + +Required properties: +- compatible : should be "st,spear1310-miphy" or "st,spear1340-miphy" +- reg : offset and length of the PHY register set. +- misc: phandle for the syscon node to access misc registers +- #phy-cells : from the generic PHY bindings, must be 1. + - cell[1]: 0 if phy used for SATA, 1 for PCIe. + +Optional properties: +- phy-id: Instance id of the phy. Only required when there are multiple phys + present on a implementation. diff --git a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt new file mode 100644 index 000000000000..16528b9eb561 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt @@ -0,0 +1,37 @@ +Allwinner sun4i USB PHY +----------------------- + +Required properties: +- compatible : should be one of + * allwinner,sun4i-a10-usb-phy + * allwinner,sun5i-a13-usb-phy + * allwinner,sun6i-a31-usb-phy + * allwinner,sun7i-a20-usb-phy +- reg : a list of offset + length pairs +- reg-names : + * "phy_ctrl" + * "pmu1" + * "pmu2" for sun4i, sun6i or sun7i +- #phy-cells : from the generic phy bindings, must be 1 +- clocks : phandle + clock specifier for the phy clocks +- clock-names : + * "usb_phy" for sun4i, sun5i or sun7i + * "usb0_phy", "usb1_phy" and "usb2_phy" for sun6i +- resets : a list of phandle + reset specifier pairs +- reset-names : + * "usb0_reset" + * "usb1_reset" + * "usb2_reset" for sun4i, sun6i or sun7i + +Example: + usbphy: phy@0x01c13400 { + #phy-cells = <1>; + compatible = "allwinner,sun4i-a10-usb-phy"; + /* phy base regs, phy1 pmu reg, phy2 pmu reg */ + reg = <0x01c13400 0x10 0x01c14800 0x4 0x01c1c800 0x4>; + reg-names = "phy_ctrl", "pmu1", "pmu2"; + clocks = <&usb_clk 8>; + clock-names = "usb_phy"; + resets = <&usb_clk 1>, <&usb_clk 2>; + reset-names = "usb1_reset", "usb2_reset"; + }; diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt new file mode 100644 index 000000000000..305e3df3d9b1 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt @@ -0,0 +1,102 @@ +TI PHY: DT DOCUMENTATION FOR PHYs in TI PLATFORMs + +OMAP CONTROL PHY + +Required properties: + - compatible: Should be one of + "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4. + "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register + e.g. USB2_PHY on OMAP5. + "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control + e.g. USB3 PHY and SATA PHY on OMAP5. + "ti,control-phy-pcie" - for pcie to support external clock for pcie and to + set PCS delay value. + e.g. PCIE PHY in DRA7x + "ti,control-phy-usb2-dra7" - if it has power down register like USB2 PHY on + DRA7 platform. + "ti,control-phy-usb2-am437" - if it has power down register like USB2 PHY on + AM437 platform. + - reg : register ranges as listed in the reg-names property + - reg-names: "otghs_control" for control-phy-otghs + "power", "pcie_pcs" and "control_sma" for control-phy-pcie + "power" for all other types + +omap_control_usb: omap-control-usb@4a002300 { + compatible = "ti,control-phy-otghs"; + reg = <0x4a00233c 0x4>; + reg-names = "otghs_control"; +}; + +OMAP USB2 PHY + +Required properties: + - compatible: Should be "ti,omap-usb2" + - reg : Address and length of the register set for the device. + - #phy-cells: determine the number of cells that should be given in the + phandle while referencing this phy. + - clocks: a list of phandles and clock-specifier pairs, one for each entry in + clock-names. + - clock-names: should include: + * "wkupclk" - wakeup clock. + * "refclk" - reference clock (optional). + +Optional properties: + - ctrl-module : phandle of the control module used by PHY driver to power on + the PHY. + +This is usually a subnode of ocp2scp to which it is connected. + +usb2phy@4a0ad080 { + compatible = "ti,omap-usb2"; + reg = <0x4a0ad080 0x58>; + ctrl-module = <&omap_control_usb>; + #phy-cells = <0>; + clocks = <&usb_phy_cm_clk32k>, <&usb_otg_ss_refclk960m>; + clock-names = "wkupclk", "refclk"; +}; + +TI PIPE3 PHY + +Required properties: + - compatible: Should be "ti,phy-usb3", "ti,phy-pipe3-sata" or + "ti,phy-pipe3-pcie. "ti,omap-usb3" is deprecated. + - reg : Address and length of the register set for the device. + - reg-names: The names of the register addresses corresponding to the registers + filled in "reg". + - #phy-cells: determine the number of cells that should be given in the + phandle while referencing this phy. + - clocks: a list of phandles and clock-specifier pairs, one for each entry in + clock-names. + - clock-names: should include: + * "wkupclk" - wakeup clock. + * "sysclk" - system clock. + * "refclk" - reference clock. + * "dpll_ref" - external dpll ref clk + * "dpll_ref_m2" - external dpll ref clk + * "phy-div" - divider for apll + * "div-clk" - apll clock + +Optional properties: + - ctrl-module : phandle of the control module used by PHY driver to power on + the PHY. + - id: If there are multiple instance of the same type, in order to + differentiate between each instance "id" can be used (e.g., multi-lane PCIe + PHY). If "id" is not provided, it is set to default value of '1'. + +This is usually a subnode of ocp2scp to which it is connected. + +usb3phy@4a084400 { + compatible = "ti,phy-usb3"; + reg = <0x4a084400 0x80>, + <0x4a084800 0x64>, + <0x4a084c00 0x40>; + reg-names = "phy_rx", "phy_tx", "pll_ctrl"; + ctrl-module = <&omap_control_usb>; + #phy-cells = <0>; + clocks = <&usb_phy_cm_clk32k>, + <&sys_clkin>, + <&usb_otg_ss_refclk960m>; + clock-names = "wkupclk", + "sysclk", + "refclk"; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index dff0e5f995e2..93ce12eb422a 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -6,8 +6,15 @@ the first two functions being GPIO in and out. The configuration on the pins includes drive strength and pull-up. Required properties: -- compatible: "allwinner,<soc>-pinctrl". Supported SoCs for now are: - sun5i-a13. +- compatible: Should be one of the followings (depending on you SoC): + "allwinner,sun4i-a10-pinctrl" + "allwinner,sun5i-a10s-pinctrl" + "allwinner,sun5i-a13-pinctrl" + "allwinner,sun6i-a31-pinctrl" + "allwinner,sun6i-a31-r-pinctrl" + "allwinner,sun7i-a20-pinctrl" + "allwinner,sun8i-a23-pinctrl" + "allwinner,sun8i-a23-r-pinctrl" - reg: Should contain the register physical address and length for the pin controller. diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt index 02ab5ab198a4..b7a93e80a302 100644 --- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt @@ -19,6 +19,7 @@ such as pull-up, multi drive, etc. Required properties for iomux controller: - compatible: "atmel,at91rm9200-pinctrl" or "atmel,at91sam9x5-pinctrl" + or "atmel,sama5d3-pinctrl" - atmel,mux-mask: array of mask (periph per bank) to describe if a pin can be configured in this periph mode. All the periph and bank need to be describe. @@ -85,13 +86,20 @@ Required properties for pin configuration node: PIN_BANK 0 is pioA, PIN_BANK 1 is pioB... Bits used for CONFIG: -PULL_UP (1 << 0): indicate this pin need a pull up. -MULTIDRIVE (1 << 1): indicate this pin need to be configured as multidrive. -DEGLITCH (1 << 2): indicate this pin need deglitch. -PULL_DOWN (1 << 3): indicate this pin need a pull down. -DIS_SCHMIT (1 << 4): indicate this pin need to disable schmit trigger. -DEBOUNCE (1 << 16): indicate this pin need debounce. -DEBOUNCE_VAL (0x3fff << 17): debounce val. +PULL_UP (1 << 0): indicate this pin needs a pull up. +MULTIDRIVE (1 << 1): indicate this pin needs to be configured as multi-drive. + Multi-drive is equivalent to open-drain type output. +DEGLITCH (1 << 2): indicate this pin needs deglitch. +PULL_DOWN (1 << 3): indicate this pin needs a pull down. +DIS_SCHMIT (1 << 4): indicate this pin needs to the disable schmitt trigger. +DRIVE_STRENGTH (3 << 5): indicate the drive strength of the pin using the + following values: + 00 - No change (reset state value kept) + 01 - Low + 10 - Medium + 11 - High +DEBOUNCE (1 << 16): indicate this pin needs debounce. +DEBOUNCE_VAL (0x3fff << 17): debounce value. NOTE: Some requirements for using atmel,at91rm9200-pinctrl binding: diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,capri-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.txt index 9e9e9ef9f852..4eaae32821ae 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,capri-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.txt @@ -1,4 +1,4 @@ -Broadcom Capri Pin Controller +Broadcom BCM281xx Pin Controller This is a pin controller for the Broadcom BCM281xx SoC family, which includes BCM11130, BCM11140, BCM11351, BCM28145, and BCM28155 SoCs. @@ -7,14 +7,14 @@ BCM11130, BCM11140, BCM11351, BCM28145, and BCM28155 SoCs. Required Properties: -- compatible: Must be "brcm,capri-pinctrl". +- compatible: Must be "brcm,bcm11351-pinctrl" - reg: Base address of the PAD Controller register block and the size of the block. For example, the following is the bare minimum node: pinctrl@35004800 { - compatible = "brcm,capri-pinctrl"; + compatible = "brcm,bcm11351-pinctrl"; reg = <0x35004800 0x430>; }; @@ -73,9 +73,9 @@ Optional Properties (for standard pins): Otherwise: 0: fast slew rate 1: normal slew rate -- input-enable: No arguements. Enable input (does not affect +- input-enable: No arguments. Enable input (does not affect output.) -- input-disable: No arguements. Disable input (does not affect +- input-disable: No arguments. Disable input (does not affect output.) - drive-strength: Integer. Drive strength in mA. Valid values are 2, 4, 6, 8, 10, 12, 14, 16 mA. @@ -99,9 +99,9 @@ Optional Properties (for I2C pins): Otherwise: 0: fast slew rate 1: normal slew rate -- input-enable: No arguements. Enable input (does not affect +- input-enable: No arguments. Enable input (does not affect output.) -- input-disable: No arguements. Disable input (does not affect +- input-disable: No arguments. Disable input (does not affect output.) Optional Properties (for HDMI pins): @@ -111,15 +111,15 @@ Optional Properties (for HDMI pins): - slew-rate: Integer. Controls slew rate. 0: Standard(100kbps)& Fast(400kbps) mode 1: Highspeed (3.4Mbps) mode -- input-enable: No arguements. Enable input (does not affect +- input-enable: No arguments. Enable input (does not affect output.) -- input-disable: No arguements. Disable input (does not affect +- input-disable: No arguments. Disable input (does not affect output.) Example: // pin controller node pinctrl@35004800 { - compatible = "brcm,capri-pinctrl"; + compatible = "brcm,bcm11351-pinctrl"; reg = <0x35004800 0x430>; // pin configuration node diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx6sx-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx6sx-pinctrl.txt new file mode 100644 index 000000000000..b1b595220f1b --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx6sx-pinctrl.txt @@ -0,0 +1,36 @@ +* Freescale i.MX6 SoloX IOMUX Controller + +Please refer to fsl,imx-pinctrl.txt in this directory for common binding part +and usage. + +Required properties: +- compatible: "fsl,imx6sx-iomuxc" +- fsl,pins: each entry consists of 6 integers and represents the mux and config + setting for one pin. The first 5 integers <mux_reg conf_reg input_reg mux_val + input_val> are specified using a PIN_FUNC_ID macro, which can be found in + imx6sx-pinfunc.h under device tree source folder. The last integer CONFIG is + the pad setting value like pull-up on this pin. Please refer to i.MX6 SoloX + Reference Manual for detailed CONFIG settings. + +CONFIG bits definition: +PAD_CTL_HYS (1 << 16) +PAD_CTL_PUS_100K_DOWN (0 << 14) +PAD_CTL_PUS_47K_UP (1 << 14) +PAD_CTL_PUS_100K_UP (2 << 14) +PAD_CTL_PUS_22K_UP (3 << 14) +PAD_CTL_PUE (1 << 13) +PAD_CTL_PKE (1 << 12) +PAD_CTL_ODE (1 << 11) +PAD_CTL_SPEED_LOW (0 << 6) +PAD_CTL_SPEED_MED (1 << 6) +PAD_CTL_SPEED_HIGH (3 << 6) +PAD_CTL_DSE_DISABLE (0 << 3) +PAD_CTL_DSE_260ohm (1 << 3) +PAD_CTL_DSE_130ohm (2 << 3) +PAD_CTL_DSE_87ohm (3 << 3) +PAD_CTL_DSE_65ohm (4 << 3) +PAD_CTL_DSE_52ohm (5 << 3) +PAD_CTL_DSE_43ohm (6 << 3) +PAD_CTL_DSE_37ohm (7 << 3) +PAD_CTL_SRE_FAST (1 << 0) +PAD_CTL_SRE_SLOW (0 << 0) diff --git a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt index a186181c402b..51b943cc9770 100644 --- a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt @@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -TZ1090-PDC's pin configuration nodes act as a container for an abitrary number +TZ1090-PDC's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt index 4b27c99f7f9d..49d0e6050940 100644 --- a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt @@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -TZ1090's pin configuration nodes act as a container for an abitrary number of +TZ1090's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt b/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt index daa768956069..ac4da9fe07bd 100644 --- a/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt +++ b/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt @@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -Lantiq's pin configuration nodes act as a container for an abitrary number of +Lantiq's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those group(s), and two pin configuration parameters: diff --git a/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt b/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt index b5469db1d7ad..e89b4677567d 100644 --- a/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt +++ b/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt @@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -Lantiq's pin configuration nodes act as a container for an abitrary number of +Lantiq's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those group(s), and two pin configuration parameters: diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-370-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-370-pinctrl.txt index 01ef408e205f..adda2a8d1d52 100644 --- a/Documentation/devicetree/bindings/pinctrl/marvell,armada-370-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-370-pinctrl.txt @@ -5,6 +5,7 @@ part and usage. Required properties: - compatible: "marvell,88f6710-pinctrl" +- reg: register specifier of MPP registers Available mpp pins/groups and functions: Note: brackets (x) are not part of the mpp name for marvell,function and given diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-375-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-375-pinctrl.txt new file mode 100644 index 000000000000..7de0cda4a379 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-375-pinctrl.txt @@ -0,0 +1,82 @@ +* Marvell Armada 375 SoC pinctrl driver for mpp + +Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding +part and usage. + +Required properties: +- compatible: "marvell,88f6720-pinctrl" +- reg: register specifier of MPP registers + +Available mpp pins/groups and functions: +Note: brackets (x) are not part of the mpp name for marvell,function and given +only for more detailed description in this document. + +name pins functions +================================================================================ +mpp0 0 gpio, dev(ad2), spi0(cs1), spi1(cs1) +mpp1 1 gpio, dev(ad3), spi0(mosi), spi1(mosi) +mpp2 2 gpio, dev(ad4), ptp(eventreq), led(c0), audio(sdi) +mpp3 3 gpio, dev(ad5), ptp(triggen), led(p3), audio(mclk) +mpp4 4 gpio, dev(ad6), spi0(miso), spi1(miso) +mpp5 5 gpio, dev(ad7), spi0(cs2), spi1(cs2) +mpp6 6 gpio, dev(ad0), led(p1), audio(rclk) +mpp7 7 gpio, dev(ad1), ptp(clk), led(p2), audio(extclk) +mpp8 8 gpio, dev (bootcs), spi0(cs0), spi1(cs0) +mpp9 9 gpio, nf(wen), spi0(sck), spi1(sck) +mpp10 10 gpio, nf(ren), dram(vttctrl), led(c1) +mpp11 11 gpio, dev(a0), led(c2), audio(sdo) +mpp12 12 gpio, dev(a1), audio(bclk) +mpp13 13 gpio, dev(readyn), pcie0(rstoutn), pcie1(rstoutn) +mpp14 14 gpio, i2c0(sda), uart1(txd) +mpp15 15 gpio, i2c0(sck), uart1(rxd) +mpp16 16 gpio, uart0(txd) +mpp17 17 gpio, uart0(rxd) +mpp18 18 gpio, tdm(intn) +mpp19 19 gpio, tdm(rstn) +mpp20 20 gpio, tdm(pclk) +mpp21 21 gpio, tdm(fsync) +mpp22 22 gpio, tdm(drx) +mpp23 23 gpio, tdm(dtx) +mpp24 24 gpio, led(p0), ge1(rxd0), sd(cmd), uart0(rts) +mpp25 25 gpio, led(p2), ge1(rxd1), sd(d0), uart0(cts) +mpp26 26 gpio, pcie0(clkreq), ge1(rxd2), sd(d2), uart1(rts) +mpp27 27 gpio, pcie1(clkreq), ge1(rxd3), sd(d1), uart1(cts) +mpp28 28 gpio, led(p3), ge1(txctl), sd(clk) +mpp29 29 gpio, pcie1(clkreq), ge1(rxclk), sd(d3) +mpp30 30 gpio, ge1(txd0), spi1(cs0) +mpp31 31 gpio, ge1(txd1), spi1(mosi) +mpp32 32 gpio, ge1(txd2), spi1(sck), ptp(triggen) +mpp33 33 gpio, ge1(txd3), spi1(miso) +mpp34 34 gpio, ge1(txclkout), spi1(sck) +mpp35 35 gpio, ge1(rxctl), spi1(cs1), spi0(cs2) +mpp36 36 gpio, pcie0(clkreq) +mpp37 37 gpio, pcie0(clkreq), tdm(intn), ge(mdc) +mpp38 38 gpio, pcie1(clkreq), ge(mdio) +mpp39 39 gpio, ref(clkout) +mpp40 40 gpio, uart1(txd) +mpp41 41 gpio, uart1(rxd) +mpp42 42 gpio, spi1(cs2), led(c0) +mpp43 43 gpio, sata0(prsnt), dram(vttctrl) +mpp44 44 gpio, sata0(prsnt) +mpp45 45 gpio, spi0(cs2), pcie0(rstoutn) +mpp46 46 gpio, led(p0), ge0(txd0), ge1(txd0) +mpp47 47 gpio, led(p1), ge0(txd1), ge1(txd1) +mpp48 48 gpio, led(p2), ge0(txd2), ge1(txd2) +mpp49 49 gpio, led(p3), ge0(txd3), ge1(txd3) +mpp50 50 gpio, led(c0), ge0(rxd0), ge1(rxd0) +mpp51 51 gpio, led(c1), ge0(rxd1), ge1(rxd1) +mpp52 52 gpio, led(c2), ge0(rxd2), ge1(rxd2) +mpp53 53 gpio, pcie1(rstoutn), ge0(rxd3), ge1(rxd3) +mpp54 54 gpio, pcie0(rstoutn), ge0(rxctl), ge1(rxctl) +mpp55 55 gpio, ge0(rxclk), ge1(rxclk) +mpp56 56 gpio, ge0(txclkout), ge1(txclkout) +mpp57 57 gpio, ge0(txctl), ge1(txctl) +mpp58 58 gpio, led(c0) +mpp59 59 gpio, led(c1) +mpp60 60 gpio, uart1(txd), led(c2) +mpp61 61 gpio, i2c1(sda), uart1(rxd), spi1(cs2), led(p0) +mpp62 62 gpio, i2c1(sck), led(p1) +mpp63 63 gpio, ptp(triggen), led(p2) +mpp64 64 gpio, dram(vttctrl), led(p3) +mpp65 65 gpio, sata1(prsnt) +mpp66 66 gpio, ptp(eventreq), spi1(cs3) diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-38x-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-38x-pinctrl.txt new file mode 100644 index 000000000000..b17c96849fc9 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-38x-pinctrl.txt @@ -0,0 +1,80 @@ +* Marvell Armada 380/385 SoC pinctrl driver for mpp + +Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding +part and usage. + +Required properties: +- compatible: "marvell,88f6810-pinctrl", "marvell,88f6820-pinctrl" or + "marvell,88f6828-pinctrl" depending on the specific variant of the + SoC being used. +- reg: register specifier of MPP registers + +Available mpp pins/groups and functions: +Note: brackets (x) are not part of the mpp name for marvell,function and given +only for more detailed description in this document. + +name pins functions +================================================================================ +mpp0 0 gpio, ua0(rxd) +mpp1 1 gpio, ua0(txd) +mpp2 2 gpio, i2c0(sck) +mpp3 3 gpio, i2c0(sda) +mpp4 4 gpio, ge(mdc), ua1(txd), ua0(rts) +mpp5 5 gpio, ge(mdio), ua1(rxd), ua0(cts) +mpp6 6 gpio, ge0(txclkout), ge0(crs), dev(cs3) +mpp7 7 gpio, ge0(txd0), dev(ad9) +mpp8 8 gpio, ge0(txd1), dev(ad10) +mpp9 9 gpio, ge0(txd2), dev(ad11) +mpp10 10 gpio, ge0(txd3), dev(ad12) +mpp11 11 gpio, ge0(txctl), dev(ad13) +mpp12 12 gpio, ge0(rxd0), pcie0(rstout), pcie1(rstout) [1], spi0(cs1), dev(ad14) +mpp13 13 gpio, ge0(rxd1), pcie0(clkreq), pcie1(clkreq) [1], spi0(cs2), dev(ad15) +mpp14 14 gpio, ge0(rxd2), ptp(clk), m(vtt_ctrl), spi0(cs3), dev(wen1) +mpp15 15 gpio, ge0(rxd3), ge(mdc slave), pcie0(rstout), spi0(mosi), pcie1(rstout) [1] +mpp16 16 gpio, ge0(rxctl), ge(mdio slave), m(decc_err), spi0(miso), pcie0(clkreq) +mpp17 17 gpio, ge0(rxclk), ptp(clk), ua1(rxd), spi0(sck), sata1(prsnt) +mpp18 18 gpio, ge0(rxerr), ptp(trig_gen), ua1(txd), spi0(cs0), pcie1(rstout) [1] +mpp19 19 gpio, ge0(col), ptp(event_req), pcie0(clkreq), sata1(prsnt), ua0(cts) +mpp20 20 gpio, ge0(txclk), ptp(clk), pcie1(rstout) [1], sata0(prsnt), ua0(rts) +mpp21 21 gpio, spi0(cs1), ge1(rxd0), sata0(prsnt), sd0(cmd), dev(bootcs) +mpp22 22 gpio, spi0(mosi), dev(ad0) +mpp23 23 gpio, spi0(sck), dev(ad2) +mpp24 24 gpio, spi0(miso), ua0(cts), ua1(rxd), sd0(d4), dev(ready) +mpp25 25 gpio, spi0(cs0), ua0(rts), ua1(txd), sd0(d5), dev(cs0) +mpp26 26 gpio, spi0(cs2), i2c1(sck), sd0(d6), dev(cs1) +mpp27 27 gpio, spi0(cs3), ge1(txclkout), i2c1(sda), sd0(d7), dev(cs2) +mpp28 28 gpio, ge1(txd0), sd0(clk), dev(ad5) +mpp29 29 gpio, ge1(txd1), dev(ale0) +mpp30 30 gpio, ge1(txd2), dev(oen) +mpp31 31 gpio, ge1(txd3), dev(ale1) +mpp32 32 gpio, ge1(txctl), dev(wen0) +mpp33 33 gpio, m(decc_err), dev(ad3) +mpp34 34 gpio, dev(ad1) +mpp35 35 gpio, ref(clk_out1), dev(a1) +mpp36 36 gpio, ptp(trig_gen), dev(a0) +mpp37 37 gpio, ptp(clk), ge1(rxclk), sd0(d3), dev(ad8) +mpp38 38 gpio, ptp(event_req), ge1(rxd1), ref(clk_out0), sd0(d0), dev(ad4) +mpp39 39 gpio, i2c1(sck), ge1(rxd2), ua0(cts), sd0(d1), dev(a2) +mpp40 40 gpio, i2c1(sda), ge1(rxd3), ua0(rts), sd0(d2), dev(ad6) +mpp41 41 gpio, ua1(rxd), ge1(rxctl), ua0(cts), spi1(cs3), dev(burst/last) +mpp42 42 gpio, ua1(txd), ua0(rts), dev(ad7) +mpp43 43 gpio, pcie0(clkreq), m(vtt_ctrl), m(decc_err), pcie0(rstout), dev(clkout) +mpp44 44 gpio, sata0(prsnt), sata1(prsnt), sata2(prsnt) [2], sata3(prsnt) [3], pcie0(rstout) +mpp45 45 gpio, ref(clk_out0), pcie0(rstout), pcie1(rstout) [1], pcie2(rstout), pcie3(rstout) +mpp46 46 gpio, ref(clk_out1), pcie0(rstout), pcie1(rstout) [1], pcie2(rstout), pcie3(rstout) +mpp47 47 gpio, sata0(prsnt), sata1(prsnt), sata2(prsnt) [2], spi1(cs2), sata3(prsnt) [2] +mpp48 48 gpio, sata0(prsnt), m(vtt_ctrl), tdm2c(pclk), audio(mclk), sd0(d4) +mpp49 49 gpio, sata2(prsnt) [2], sata3(prsnt) [2], tdm2c(fsync), audio(lrclk), sd0(d5) +mpp50 50 gpio, pcie0(rstout), pcie1(rstout) [1], tdm2c(drx), audio(extclk), sd0(cmd) +mpp51 51 gpio, tdm2c(dtx), audio(sdo), m(decc_err) +mpp52 52 gpio, pcie0(rstout), pcie1(rstout) [1], tdm2c(intn), audio(sdi), sd0(d6) +mpp53 53 gpio, sata1(prsnt), sata0(prsnt), tdm2c(rstn), audio(bclk), sd0(d7) +mpp54 54 gpio, sata0(prsnt), sata1(prsnt), pcie0(rstout), pcie1(rstout) [1], sd0(d3) +mpp55 55 gpio, ua1(cts), ge(mdio), pcie1(clkreq) [1], spi1(cs1), sd0(d0) +mpp56 56 gpio, ua1(rts), ge(mdc), m(decc_err), spi1(mosi) +mpp57 57 gpio, spi1(sck), sd0(clk) +mpp58 58 gpio, pcie1(clkreq) [1], i2c1(sck), pcie2(clkreq), spi1(miso), sd0(d1) +mpp59 59 gpio, pcie0(rstout), i2c1(sda), pcie1(rstout) [1], spi1(cs0), sd0(d2) + +[1]: only available on 88F6820 and 88F6828 +[2]: only available on 88F6828 diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt index bfa0a2e5e0cb..373dbccd7ab0 100644 --- a/Documentation/devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt @@ -6,6 +6,7 @@ part and usage. Required properties: - compatible: "marvell,mv78230-pinctrl", "marvell,mv78260-pinctrl", "marvell,mv78460-pinctrl" +- reg: register specifier of MPP registers This driver supports all Armada XP variants, i.e. mv78230, mv78260, and mv78460. diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,dove-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,dove-pinctrl.txt index 50ec3512a292..cf52477cc7ee 100644 --- a/Documentation/devicetree/bindings/pinctrl/marvell,dove-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/marvell,dove-pinctrl.txt @@ -6,6 +6,7 @@ part and usage. Required properties: - compatible: "marvell,dove-pinctrl" - clocks: (optional) phandle of pdma clock +- reg: register specifiers of MPP, MPP4, and PMU MPP registers Available mpp pins/groups and functions: Note: brackets (x) are not part of the mpp name for marvell,function and given diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt index 95daf6335c37..730444a9a4de 100644 --- a/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt @@ -8,6 +8,7 @@ Required properties: "marvell,88f6190-pinctrl", "marvell,88f6192-pinctrl", "marvell,88f6281-pinctrl", "marvell,88f6282-pinctrl" "marvell,98dx4122-pinctrl" +- reg: register specifier of MPP registers This driver supports all kirkwood variants, i.e. 88f6180, 88f619x, and 88f628x. It also support the 88f6281-based variant in the 98dx412x Bobcat SoCs. diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,mvebu-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,mvebu-pinctrl.txt index 0a26c3aa4e6d..0c09f4eb2af0 100644 --- a/Documentation/devicetree/bindings/pinctrl/marvell,mvebu-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/marvell,mvebu-pinctrl.txt @@ -37,7 +37,7 @@ uart1: serial@12100 { pinctrl: pinctrl@d0200 { compatible = "marvell,dove-pinctrl"; - reg = <0xd0200 0x20>; + reg = <0xd0200 0x14>, <0xd0440 0x04>, <0xd802c 0x08>; pmx_uart1_sw: pmx-uart1-sw { marvell,pins = "mpp_uart1"; diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,orion-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,orion-pinctrl.txt new file mode 100644 index 000000000000..27570a3a1741 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/marvell,orion-pinctrl.txt @@ -0,0 +1,91 @@ +* Marvell Orion SoC pinctrl driver for mpp + +Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding +part and usage. + +Required properties: +- compatible: "marvell,88f5181l-pinctrl", "marvell,88f5182-pinctrl", + "marvell,88f5281-pinctrl" + +- reg: two register areas, the first one describing the first two + contiguous MPP registers, and the second one describing the single + final MPP register, separated from the previous one. + +Available mpp pins/groups and functions: +Note: brackets (x) are not part of the mpp name for marvell,function and given +only for more detailed description in this document. + +* Marvell Orion 88f5181l + +name pins functions +================================================================================ +mpp0 0 pcie(rstout), pci(req2), gpio +mpp1 1 gpio, pci(gnt2) +mpp2 2 gpio, pci(req3), pci-1(pme) +mpp3 3 gpio, pci(gnt3) +mpp4 4 gpio, pci(req4) +mpp5 5 gpio, pci(gnt4) +mpp6 6 gpio, pci(req5), pci-1(clk) +mpp7 7 gpio, pci(gnt5), pci-1(clk) +mpp8 8 gpio, ge(col) +mpp9 9 gpio, ge(rxerr) +mpp10 10 gpio, ge(crs) +mpp11 11 gpio, ge(txerr) +mpp12 12 gpio, ge(txd4) +mpp13 13 gpio, ge(txd5) +mpp14 14 gpio, ge(txd6) +mpp15 15 gpio, ge(txd7) +mpp16 16 ge(rxd4) +mpp17 17 ge(rxd5) +mpp18 18 ge(rxd6) +mpp19 19 ge(rxd7) + +* Marvell Orion 88f5182 + +name pins functions +================================================================================ +mpp0 0 pcie(rstout), pci(req2), gpio +mpp1 1 gpio, pci(gnt2) +mpp2 2 gpio, pci(req3), pci-1(pme) +mpp3 3 gpio, pci(gnt3) +mpp4 4 gpio, pci(req4), bootnand(re), sata0(prsnt) +mpp5 5 gpio, pci(gnt4), bootnand(we), sata1(prsnt) +mpp6 6 gpio, pci(req5), nand(re0), sata0(act) +mpp7 7 gpio, pci(gnt5), nand(we0), sata1(act) +mpp8 8 gpio, ge(col) +mpp9 9 gpio, ge(rxerr) +mpp10 10 gpio, ge(crs) +mpp11 11 gpio, ge(txerr) +mpp12 12 gpio, ge(txd4), nand(re1), sata0(ledprsnt) +mpp13 13 gpio, ge(txd5), nand(we1), sata1(ledprsnt) +mpp14 14 gpio, ge(txd6), nand(re2), sata0(ledact) +mpp15 15 gpio, ge(txd7), nand(we2), sata1(ledact) +mpp16 16 uart1(rxd), ge(rxd4), gpio +mpp17 17 uart1(txd), ge(rxd5), gpio +mpp18 18 uart1(cts), ge(rxd6), gpio +mpp19 19 uart1(rts), ge(rxd7), gpio + +* Marvell Orion 88f5281 + +name pins functions +================================================================================ +mpp0 0 pcie(rstout), pci(req2), gpio +mpp1 1 gpio, pci(gnt2) +mpp2 2 gpio, pci(req3), pci(pme) +mpp3 3 gpio, pci(gnt3) +mpp4 4 gpio, pci(req4), bootnand(re) +mpp5 5 gpio, pci(gnt4), bootnand(we) +mpp6 6 gpio, pci(req5), nand(re0) +mpp7 7 gpio, pci(gnt5), nand(we0) +mpp8 8 gpio, ge(col) +mpp9 9 gpio, ge(rxerr) +mpp10 10 gpio, ge(crs) +mpp11 11 gpio, ge(txerr) +mpp12 12 gpio, ge(txd4), nand(re1) +mpp13 13 gpio, ge(txd5), nand(we1) +mpp14 14 gpio, ge(txd6), nand(re2) +mpp15 15 gpio, ge(txd7), nand(we2) +mpp16 16 uart1(rxd), ge(rxd4) +mpp17 17 uart1(txd), ge(rxd5) +mpp18 18 uart1(cts), ge(rxd6) +mpp19 19 uart1(rts), ge(rxd7) diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-pinmux.txt index 6464bf769460..189814e7cdc7 100644 --- a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-pinmux.txt +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-pinmux.txt @@ -10,6 +10,7 @@ Required properties: - reg: Should contain a list of base address and size pairs for: -- first entry - the drive strength and pad control registers. -- second entry - the pinmux registers + -- third entry - the MIPI_PAD_CTRL register Tegra124 adds the following optional properties for pin configuration subnodes. The macros for options are defined in the @@ -91,6 +92,12 @@ Valid values for pin and group names are: dbg, sdio3, spi, uaa, uab, uart2, uart3, sdio1, ddc, gma, gme, gmf, gmg, gmh, owr, uda, gpv, dev3, cec, usb_vbus_en, ao3, ao0, hv0, sdio4, ao4. + MIPI pad control groups: + + These support only the nvidia,function property. + + dsi_b + Valid values for nvidia,functions are: blink, cec, cldvfs, clk12, cpu, dap, dap1, dap2, dev3, displaya, @@ -101,14 +108,15 @@ Valid values for nvidia,functions are: sdmmc4, soc, spdif, spi1, spi2, spi3, spi4, spi5, spi6, trace, uarta, uartb, uartc, uartd, ulpi, usb, vgp1, vgp2, vgp3, vgp4, vgp5, vgp6, vi, vi_alt1, vi_alt3, vimclk2, vimclk2_alt, sata, ccla, pe0, pe, pe1, - dp, rtck, sys, clk tmds. + dp, rtck, sys, clk tmds, csi, dsi_b Example: pinmux: pinmux { compatible = "nvidia,tegra124-pinmux"; - reg = <0x70000868 0x164 /* Pad control registers */ - 0x70003000 0x434>; /* PinMux registers */ + reg = <0x0 0x70000868 0x0 0x164>, /* Pad control registers */ + <0x0 0x70003000 0x0 0x434>, /* Mux registers */ + <0x0 0x70000820 0x0 0x8>; /* MIPI pad control */ }; Example pinmux entries: diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt new file mode 100644 index 000000000000..2f9c0bd66457 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt @@ -0,0 +1,127 @@ +Device tree binding for NVIDIA Tegra XUSB pad controller +======================================================== + +The Tegra XUSB pad controller manages a set of lanes, each of which can be +assigned to one out of a set of different pads. Some of these pads have an +associated PHY that must be powered up before the pad can be used. + +This document defines the device-specific binding for the XUSB pad controller. + +Refer to pinctrl-bindings.txt in this directory for generic information about +pin controller device tree bindings and ../phy/phy-bindings.txt for details on +how to describe and reference PHYs in device trees. + +Required properties: +-------------------- +- compatible: should be "nvidia,tegra124-xusb-padctl" +- reg: Physical base address and length of the controller's registers. +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - padctl +- #phy-cells: Should be 1. The specifier is the index of the PHY to reference. + See <dt-bindings/pinctrl/pinctrl-tegra-xusb.h> for the list of valid values. + +Lane muxing: +------------ + +Child nodes contain the pinmux configurations following the conventions from +the pinctrl-bindings.txt document. Typically a single, static configuration is +given and applied at boot time. + +Each subnode describes groups of lanes along with parameters and pads that +they should be assigned to. The name of these subnodes is not important. All +subnodes should be parsed solely based on their content. + +Each subnode only applies the parameters that are explicitly listed. In other +words, if a subnode that lists a function but no pin configuration parameters +implies no information about any pin configuration parameters. Similarly, a +subnode that describes only an IDDQ parameter implies no information about +what function the pins are assigned to. For this reason even seemingly boolean +values are actually tristates in this binding: unspecified, off or on. +Unspecified is represented as an absent property, and off/on are represented +as integer values 0 and 1. + +Required properties: +- nvidia,lanes: An array of strings. Each string is the name of a lane. + +Optional properties: +- nvidia,function: A string that is the name of the function (pad) that the + pin or group should be assigned to. Valid values for function names are + listed below. +- nvidia,iddq: Enables IDDQ mode of the lane. (0: no, 1: yes) + +Note that not all of these properties are valid for all lanes. Lanes can be +divided into three groups: + + - otg-0, otg-1, otg-2: + + Valid functions for this group are: "snps", "xusb", "uart", "rsvd". + + The nvidia,iddq property does not apply to this group. + + - ulpi-0, hsic-0, hsic-1: + + Valid functions for this group are: "snps", "xusb". + + The nvidia,iddq property does not apply to this group. + + - pcie-0, pcie-1, pcie-2, pcie-3, pcie-4, sata-0: + + Valid functions for this group are: "pcie", "usb3", "sata", "rsvd". + + +Example: +======== + +SoC file extract: +----------------- + + padctl@0,7009f000 { + compatible = "nvidia,tegra124-xusb-padctl"; + reg = <0x0 0x7009f000 0x0 0x1000>; + resets = <&tegra_car 142>; + reset-names = "padctl"; + + #phy-cells = <1>; + }; + +Board file extract: +------------------- + + pcie-controller@0,01003000 { + ... + + phys = <&padctl 0>; + phy-names = "pcie"; + + ... + }; + + ... + + padctl: padctl@0,7009f000 { + pinctrl-0 = <&padctl_default>; + pinctrl-names = "default"; + + padctl_default: pinmux { + usb3 { + nvidia,lanes = "pcie-0", "pcie-1"; + nvidia,function = "usb3"; + nvidia,iddq = <0>; + }; + + pcie { + nvidia,lanes = "pcie-2", "pcie-3", + "pcie-4"; + nvidia,function = "pcie"; + nvidia,iddq = <0>; + }; + + sata { + nvidia,lanes = "sata-0"; + nvidia,function = "sata"; + nvidia,iddq = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt index 61e73cde9ae9..3c8ce28baad6 100644 --- a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt @@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -Tegra's pin configuration nodes act as a container for an abitrary number of +Tegra's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt index 4414163e76d2..98eb94d91a1c 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt @@ -127,6 +127,24 @@ whether there is any interaction between the child and intermediate parent nodes, is again defined entirely by the binding for the individual pin controller device. +== Generic pin multiplexing node content == + +pin multiplexing nodes: + +function - the mux function to select +groups - the list of groups to select with this function + +Example: + +state_0_node_a { + function = "uart0"; + groups = "u0rxtx", "u0rtscts"; +}; +state_1_node_a { + function = "spi0"; + groups = "spi0pins"; +}; + == Generic pin configuration node content == Many data items that are represented in a pin configuration node are common @@ -139,8 +157,12 @@ structure of the DT nodes that contain these properties. Supported generic properties are: pins - the list of pins that properties in the node - apply to -function - the mux function to select + apply to (either this or "group" has to be + specified) +group - the group to apply the properties to, if the driver + supports configuration of whole groups rather than + individual pins (either this or "pins" has to be + specified) bias-disable - disable any pin bias bias-high-impedance - high impedance mode ("third-state", "floating") bias-bus-hold - latch weakly @@ -156,12 +178,28 @@ input-disable - disable input on pin (no effect on output) input-schmitt-enable - enable schmitt-trigger mode input-schmitt-disable - disable schmitt-trigger mode input-debounce - debounce mode with debound time X +power-source - select between different power supplies low-power-enable - enable low power mode low-power-disable - disable low power mode output-low - set the pin to output mode with low level output-high - set the pin to output mode with high level slew-rate - set the slew rate +For example: + +state_0_node_a { + pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */ + bias-pull-up; +}; +state_1_node_a { + pins = "GPIO1_AJ3", "GPIO3_AH3"; /* RTS+TXD */ + output-high; +}; +state_2_node_a { + group = "foo-group"; + bias-pull-up; +}; + Some of the generic properties take arguments. For those that do, the arguments are described below. @@ -169,15 +207,6 @@ arguments are described below. binding for the hardware defines: - Whether the entries are integers or strings, and their meaning. -- function takes a list of function names/IDs as a required argument. The - specific binding for the hardware defines: - - Whether the entries are integers or strings, and their meaning. - - Whether only a single entry is allowed (which is applied to all entries - in the pins property), or whether there may alternatively be one entry per - entry in the pins property, in which case the list lengths must match, and - for each list index i, the function at list index i is applied to the pin - at list index i. - - bias-pull-up, -down and -pin-default take as optional argument on hardware supporting it the pull strength in Ohm. bias-disable will disable the pull. diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt index bc0dfdfdb148..66dcaa9efd74 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt @@ -63,6 +63,13 @@ Optional properties: /* input, enable bits, disable bits, mask */ pinctrl-single,input-schmitt-enable = <0x30 0x40 0 0x70>; +- pinctrl-single,low-power-mode : array of value that are used to configure + low power mode of this pin. For some silicons, the low power mode will + control the output of the pin when the pad including the pin enter low + power mode. + /* low power mode value, mask */ + pinctrl-single,low-power-mode = <0x288 0x388>; + - pinctrl-single,gpio-range : list of value that are used to configure a GPIO range. They're value of subnode phandle, pin base in pinctrl device, pin number in this range, GPIO function value of this GPIO range. diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt index c596a6ad3285..5f55be59d914 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt @@ -13,7 +13,7 @@ Optional properties: Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices. -SiRFprimaII's pinmux nodes act as a container for an abitrary number of subnodes. +SiRFprimaII's pinmux nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a group of pins. Required subnode-properties: diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt index 05bf82a07dfd..26bcb18f4e60 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt @@ -11,18 +11,68 @@ Pull Up (PU) are driven by the related PIO block. ST pinctrl driver controls PIO multiplexing block and also interacts with gpio driver to configure a pin. -Required properties: (PIO multiplexing block) +GPIO bank can have one of the two possible types of interrupt-wirings. + +First type is via irqmux, single interrupt is used by multiple gpio banks. This +reduces number of overall interrupts numbers required. All these banks belong to +a single pincontroller. + _________ + | |----> [gpio-bank (n) ] + | |----> [gpio-bank (n + 1)] + [irqN]-- | irq-mux |----> [gpio-bank (n + 2)] + | |----> [gpio-bank (... )] + |_________|----> [gpio-bank (n + 7)] + +Second type has a dedicated interrupt per gpio bank. + + [irqN]----> [gpio-bank (n)] + + +Pin controller node: +Required properties: - compatible : should be "st,<SOC>-<pio-block>-pinctrl" like st,stih415-sbc-pinctrl, st,stih415-front-pinctrl and so on. -- gpio-controller : Indicates this device is a GPIO controller -- #gpio-cells : Should be one. The first cell is the pin number. +- st,syscfg : Should be a phandle of the syscfg node. - st,retime-pin-mask : Should be mask to specify which pins can be retimed. If the property is not present, it is assumed that all the pins in the bank are capable of retiming. Retiming is mainly used to improve the IO timing margins of external synchronous interfaces. -- st,bank-name : Should be a name string for this bank as - specified in datasheet. -- st,syscfg : Should be a phandle of the syscfg node. +- ranges : defines mapping between pin controller node (parent) to gpio-bank + node (children). + +Optional properties: +- interrupts : Interrupt number of the irqmux. If the interrupt is shared + with other gpio banks via irqmux. + a irqline and gpio banks. +- reg : irqmux memory resource. If irqmux is present. +- reg-names : irqmux resource should be named as "irqmux". + +GPIO controller/bank node. +Required properties: +- gpio-controller : Indicates this device is a GPIO controller +- #gpio-cells : Should be one. The first cell is the pin number. +- st,bank-name : Should be a name string for this bank as specified in + datasheet. + +Optional properties: +- interrupts : Interrupt number for this gpio bank. If there is a dedicated + interrupt wired up for this gpio bank. + +- interrupt-controller : Indicates this device is a interrupt controller. GPIO + bank can be an interrupt controller iff one of the interrupt type either via +irqmux or a dedicated interrupt per bank is specified. + +- #interrupt-cells: the value of this property should be 2. + - First Cell: represents the external gpio interrupt number local to the + gpio interrupt space of the controller. + - Second Cell: flags to identify the type of the interrupt + - 1 = rising edge triggered + - 2 = falling edge triggered + - 3 = rising and falling edge triggered + - 4 = high level triggered + - 8 = low level triggered +for related macros look in: +include/dt-bindings/interrupt-controller/irq.h Example: pin-controller-sbc { @@ -30,10 +80,17 @@ Example: #size-cells = <1>; compatible = "st,stih415-sbc-pinctrl"; st,syscfg = <&syscfg_sbc>; + reg = <0xfe61f080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "irqmux"; ranges = <0 0xfe610000 0x5000>; + PIO0: gpio@fe610000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0 0x100>; st,bank-name = "PIO0"; }; @@ -105,6 +162,10 @@ pin-controller { sdhci0:sdhci@fe810000{ ... + interrupt-parent = <&PIO3>; + #interrupt-cells = <2>; + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; /* Interrupt line via PIO3-3 */ + interrupt-names = "card-detect"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_mmc>; }; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt index b4480d5c3aca..458615596946 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt @@ -32,7 +32,7 @@ Required properties: Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices. -SPEAr's pinmux nodes act as a container for an abitrary number of subnodes. Each +SPEAr's pinmux nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents muxing for a pin, a group, or a list of pins or groups. diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt new file mode 100644 index 000000000000..a7bde64798c7 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt @@ -0,0 +1,88 @@ +Qualcomm APQ8064 TLMM block + +Required properties: +- compatible: "qcom,apq8064-pinctrl" +- reg: Should be the base address and length of the TLMM block. +- interrupts: Should be the parent IRQ of the TLMM block. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Should be two. +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells : Should be two. + The first cell is the gpio pin number and the + second cell is used for optional parameters. + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Qualcomm's pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + + pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength, + output-low, output-high. + +Non-empty subnodes must specify the 'pins' property. + +Valid values for pins are: + gpio0-gpio89 + +Valid values for function are: + cam_mclk, codec_mic_i2s, codec_spkr_i2s, gpio, gsbi1, gsbi2, gsbi3, gsbi4, + gsbi4_cam_i2c, gsbi5, gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6, + gsbi6_spi_cs1, gsbi6_spi_cs2, gsbi6_spi_cs3, gsbi7, gsbi7_spi_cs1, + gsbi7_spi_cs2, gsbi7_spi_cs3, gsbi_cam_i2c, hdmi, mi2s, riva_bt, riva_fm, + riva_wlan, sdc2, sdc4, slimbus, spkr_i2s, tsif1, tsif2, usb2_hsic, ps_hold + +Example: + + msmgpio: pinctrl@800000 { + compatible = "qcom,apq8064-pinctrl"; + reg = <0x800000 0x4000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 16 0x4>; + + pinctrl-names = "default"; + pinctrl-0 = <&gsbi5_uart_default>; + + gsbi5_uart_default: gsbi5_uart_default { + mux { + pins = "gpio51", "gpio52"; + function = "gsbi5"; + }; + + tx { + pins = "gpio51"; + drive-strength = <4>; + bias-disable; + }; + + rx { + pins = "gpio52"; + drive-strength = <2>; + bias-pull-up; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt new file mode 100644 index 000000000000..c4ea61ac56f2 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt @@ -0,0 +1,179 @@ +Qualcomm APQ8084 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +MSM8960 platform. + +- compatible: + Usage: required + Value type: <string> + Definition: must be "qcom,apq8084-pinctrl" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the TLMM register space. + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: <none> + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/interrupt-controller/irq.h> + +- gpio-controller: + Usage: required + Value type: <none> + Definition: identifies this node as a gpio controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/gpio/gpio.h> + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. Valid pins are: + gpio0-gpio146, + sdc1_clk, + sdc1_cmd, + sdc1_data + sdc2_clk, + sdc2_cmd, + sdc2_data + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Functions are only valid for gpio pins. + Valid values are: + adsp_ext, audio_ref, blsp_i2c1, blsp_i2c2, blsp_i2c3, + blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_i2c7, blsp_i2c8, + blsp_i2c9, blsp_i2c10, blsp_i2c11, blsp_i2c12, + blsp_spi1, blsp_spi2, blsp_spi3, blsp_spi4, blsp_spi5, + blsp_spi6, blsp_spi7, blsp_spi8, blsp_spi9, blsp_spi10, + blsp_spi11, blsp_spi12, blsp_uart1, blsp_uart2, blsp_uart3, + blsp_uart4, blsp_uart5, blsp_uart6, blsp_uart7, blsp_uart8, + blsp_uart9, blsp_uart10, blsp_uart11, blsp_uart12, + blsp_uim1, blsp_uim2, blsp_uim3, blsp_uim4, blsp_uim5, + blsp_uim6, blsp_uim7, blsp_uim8, blsp_uim9, blsp_uim10, + blsp_uim11, blsp_uim12, cam_mclk0, cam_mclk1, cam_mclk2, + cam_mclk3, cci_async, cci_async_in0, cci_i2c0, cci_i2c1, + cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4, + edp_hpd, gcc_gp1, gcc_gp2, gcc_gp3, gcc_obt, gcc_vtt,i + gp_mn, gp_pdm0, gp_pdm1, gp_pdm2, gp0_clk, gp1_clk, gpio, + hdmi_cec, hdmi_ddc, hdmi_dtest, hdmi_hpd, hdmi_rcv, hsic, + ldo_en, ldo_update, mdp_vsync, pci_e0, pci_e0_n, pci_e0_rst, + pci_e1, pci_e1_rst, pci_e1_rst_n, pci_e1_clkreq_n, pri_mi2s, + qua_mi2s, sata_act, sata_devsleep, sata_devsleep_n, + sd_write, sdc_emmc_mode, sdc3, sdc4, sec_mi2s, slimbus, + spdif_tx, spkr_i2s, spkr_i2s_ws, spss_geni, ter_mi2s, tsif1, + tsif2, uim, uim_batt_alarm + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull down. + +- bias-pull-up: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull up. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + Not valid for sdc pins. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + Not valid for sdc pins. + +- drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + tlmm: pinctrl@fd510000 { + compatible = "qcom,apq8084-pinctrl"; + reg = <0xfd510000 0x4000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 208 0>; + + uart2: uart2-default { + mux { + pins = "gpio4", "gpio5"; + function = "blsp_uart2"; + }; + + tx { + pins = "gpio4"; + drive-strength = <4>; + bias-disable; + }; + + rx { + pins = "gpio5"; + drive-strength = <2>; + bias-pull-up; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt new file mode 100644 index 000000000000..6e88e91feb11 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt @@ -0,0 +1,95 @@ +Qualcomm IPQ8064 TLMM block + +Required properties: +- compatible: "qcom,ipq8064-pinctrl" +- reg: Should be the base address and length of the TLMM block. +- interrupts: Should be the parent IRQ of the TLMM block. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Should be two. +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells : Should be two. + The first cell is the gpio pin number and the + second cell is used for optional parameters. + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Qualcomm's pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + + pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength, + output-low, output-high. + +Non-empty subnodes must specify the 'pins' property. + +Valid values for qcom,pins are: + gpio0-gpio68 + Supports mux, bias, and drive-strength + + sdc3_clk, sdc3_cmd, sdc3_data + Supports bias and drive-strength + + +Valid values for function are: + mdio, mi2s, pdm, ssbi, spmi, audio_pcm, gpio, gsbi1, gsbi2, gsbi4, gsbi5, + gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6, gsbi7, nss_spi, sdc1, + spdif, nand, tsif1, tsif2, usb_fs_n, usb_fs, usb2_hsic, rgmii2, sata, + pcie1_rst, pcie1_prsnt, pcie1_pwren_n, pcie1_pwren, pcie1_pwrflt, + pcie1_clk_req, pcie2_rst, pcie2_prsnt, pcie2_pwren_n, pcie2_pwren, + pcie2_pwrflt, pcie2_clk_req, pcie3_rst, pcie3_prsnt, pcie3_pwren_n, + pcie3_pwren, pcie3_pwrflt, pcie3_clk_req, ps_hold + +Example: + + pinmux: pinctrl@800000 { + compatible = "qcom,ipq8064-pinctrl"; + reg = <0x800000 0x4000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 32 0x4>; + + pinctrl-names = "default"; + pinctrl-0 = <&gsbi5_uart_default>; + + gsbi5_uart_default: gsbi5_uart_default { + mux { + pins = "gpio18", "gpio19"; + function = "gsbi5"; + }; + + tx { + pins = "gpio18"; + drive-strength = <4>; + bias-disable; + }; + + rx { + pins = "gpio19"; + drive-strength = <2>; + bias-pull-up; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt new file mode 100644 index 000000000000..eb8d8aa41f20 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt @@ -0,0 +1,181 @@ +Qualcomm MSM8960 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +MSM8960 platform. + +- compatible: + Usage: required + Value type: <string> + Definition: must be "qcom,msm8960-pinctrl" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the TLMM register space. + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: <none> + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/interrupt-controller/irq.h> + +- gpio-controller: + Usage: required + Value type: <none> + Definition: identifies this node as a gpio controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/gpio/gpio.h> + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. Valid pins are: + gpio0-gpio151, + sdc1_clk, + sdc1_cmd, + sdc1_data + sdc3_clk, + sdc3_cmd, + sdc3_data + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Functions are only valid for gpio pins. + Valid values are: + audio_pcm, bt, cam_mclk0, cam_mclk1, cam_mclk2, + codec_mic_i2s, codec_spkr_i2s, ext_gps, fm, gps_blanking, + gps_pps_in, gps_pps_out, gp_clk_0a, gp_clk_0b, gp_clk_1a, + gp_clk_1b, gp_clk_2a, gp_clk_2b, gp_mn, gp_pdm_0a, + gp_pdm_0b, gp_pdm_1a, gp_pdm_1b, gp_pdm_2a, gp_pdm_2b, gpio, + gsbi1, gsbi1_spi_cs1_n, gsbi1_spi_cs2a_n, gsbi1_spi_cs2b_n, + gsbi1_spi_cs3_n, gsbi2, gsbi2_spi_cs1_n, gsbi2_spi_cs2_n, + gsbi2_spi_cs3_n, gsbi3, gsbi4, gsbi4_3d_cam_i2c_l, + gsbi4_3d_cam_i2c_r, gsbi5, gsbi5_3d_cam_i2c_l, + gsbi5_3d_cam_i2c_r, gsbi6, gsbi7, gsbi8, gsbi9, gsbi10, + gsbi11, gsbi11_spi_cs1a_n, gsbi11_spi_cs1b_n, + gsbi11_spi_cs2a_n, gsbi11_spi_cs2b_n, gsbi11_spi_cs3_n, + gsbi12, hdmi_cec, hdmi_ddc_clock, hdmi_ddc_data, + hdmi_hot_plug_detect, hsic, mdp_vsync, mi2s, mic_i2s, + pmb_clk, pmb_ext_ctrl, ps_hold, rpm_wdog, sdc2, sdc4, sdc5, + slimbus1, slimbus2, spkr_i2s, ssbi1, ssbi2, ssbi_ext_gps, + ssbi_pmic2, ssbi_qpa1, ssbi_ts, tsif1, tsif2, ts_eoc, + usb_fs1, usb_fs1_oe, usb_fs1_oe_n, usb_fs2, usb_fs2_oe, + usb_fs2_oe_n, vfe_camif_timer1_a, vfe_camif_timer1_b, + vfe_camif_timer2, vfe_camif_timer3_a, vfe_camif_timer3_b, + vfe_camif_timer4_a, vfe_camif_timer4_b, vfe_camif_timer4_c, + vfe_camif_timer5_a, vfe_camif_timer5_b, vfe_camif_timer6_a, + vfe_camif_timer6_b, vfe_camif_timer6_c, vfe_camif_timer7_a, + vfe_camif_timer7_b, vfe_camif_timer7_c, wlan + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull down. + +- bias-pull-up: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull up. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + Not valid for sdc pins. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + Not valid for sdc pins. + +- drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + msmgpio: pinctrl@800000 { + compatible = "qcom,msm8960-pinctrl"; + reg = <0x800000 0x4000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 16 0x4>; + + gsbi8_uart: gsbi8-uart { + mux { + pins = "gpio34", "gpio35"; + function = "gsbi8"; + }; + + tx { + pins = "gpio34"; + drive-strength = <4>; + bias-disable; + }; + + rx { + pins = "gpio35"; + drive-strength = <2>; + bias-pull-up; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt index 4c352be5dd61..e4d6a9d20f7d 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt @@ -1,7 +1,7 @@ Qualcomm MSM8974 TLMM block Required properties: -- compatible: "qcom,msm8x74-pinctrl" +- compatible: "qcom,msm8974-pinctrl" - reg: Should be the base address and length of the TLMM block. - interrupts: Should be the parent IRQ of the TLMM block. - interrupt-controller: Marks the device node as an interrupt controller. @@ -18,7 +18,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -Qualcomm's pin configuration nodes act as a container for an abitrary number of +Qualcomm's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration @@ -42,15 +42,35 @@ Non-empty subnodes must specify the 'pins' property. Note that not all properties are valid for all pins. -Valid values for qcom,pins are: +Valid values for pins are: gpio0-gpio145 Supports mux, bias and drive-strength sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data Supports bias and drive-strength -Valid values for qcom,function are: - blsp_i2c2, blsp_i2c6, blsp_i2c11, blsp_spi1, blsp_uart2, blsp_uart8, slimbus +Valid values for function are: + cci_i2c0, cci_i2c1, uim1, uim2, uim_batt_alarm, + blsp_uim1, blsp_uart1, blsp_i2c1, blsp_spi1, + blsp_uim2, blsp_uart2, blsp_i2c2, blsp_spi2, + blsp_uim3, blsp_uart3, blsp_i2c3, blsp_spi3, + blsp_uim4, blsp_uart4, blsp_i2c4, blsp_spi4, + blsp_uim5, blsp_uart5, blsp_i2c5, blsp_spi5, + blsp_uim6, blsp_uart6, blsp_i2c6, blsp_spi6, + blsp_uim7, blsp_uart7, blsp_i2c7, blsp_spi7, + blsp_uim8, blsp_uart8, blsp_i2c8, blsp_spi8, + blsp_uim9, blsp_uart9, blsp_i2c9, blsp_spi9, + blsp_uim10, blsp_uart10, blsp_i2c10, blsp_spi10, + blsp_uim11, blsp_uart11, blsp_i2c11, blsp_spi11, + blsp_uim12, blsp_uart12, blsp_i2c12, blsp_spi12, + blsp_spi1_cs1, blsp_spi2_cs2, blsp_spi_cs3, blsp_spi2_cs1, blsp_spi2_cs2 + blsp_spi2_cs3, blsp_spi10_cs1, blsp_spi10_cs2, blsp_spi10_cs3, + sdc3, sdc4, gcc_gp_clk1, gcc_gp_clk2, gcc_gp_clk3, cci_timer0, cci_timer1, + cci_timer2, cci_timer3, cci_async_in0, cci_async_in1, cci_async_in2, + cam_mckl0, cam_mclk1, cam_mclk2, cam_mclk3, mdp_vsync, hdmi_cec, hdmi_ddc, + hdmi_hpd, edp_hpd, gp_pdm0, gp_pdm1, gp_pdm2, gp_pdm3, gp0_clk, gp1_clk, + gp_mn, tsif1, tsif2, hsic, grfc, audio_ref_clk, qua_mi2s, pri_mi2s, spkr_mi2s, + ter_mi2s, sec_mi2s, bt, fm, wlan, slimbus, gpio (Note that this is not yet the complete list of functions) @@ -73,18 +93,18 @@ Example: uart2_default: uart2_default { mux { - qcom,pins = "gpio4", "gpio5"; - qcom,function = "blsp_uart2"; + pins = "gpio4", "gpio5"; + function = "blsp_uart2"; }; tx { - qcom,pins = "gpio4"; + pins = "gpio4"; drive-strength = <4>; bias-disable; }; rx { - qcom,pins = "gpio5"; + pins = "gpio5"; drive-strength = <2>; bias-pull-up; }; diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt index 35d2e1f186f0..daef6fad6a5f 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -15,6 +15,7 @@ Required Properties: - "renesas,pfc-r8a7778": for R8A7778 (R-Mobile M1) compatible pin-controller. - "renesas,pfc-r8a7779": for R8A7779 (R-Car H1) compatible pin-controller. - "renesas,pfc-r8a7790": for R8A7790 (R-Car H2) compatible pin-controller. + - "renesas,pfc-r8a7791": for R8A7791 (R-Car M2) compatible pin-controller. - "renesas,pfc-sh7372": for SH7372 (SH-Mobile AP4) compatible pin-controller. - "renesas,pfc-sh73a0": for SH73A0 (SH-Mobile AG5) compatible pin-controller. diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt index f378d342aae4..388b213249fd 100644 --- a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt @@ -2,8 +2,8 @@ The Rockchip Pinmux Controller, enables the IC to share one PAD to several functional blocks. The sharing is done by -multiplexing the PAD input/output signals. For each PAD there are up to -4 muxing options with option 0 being the use as a GPIO. +multiplexing the PAD input/output signals. For each PAD there are several +muxing options with option 0 being the use as a GPIO. Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the @@ -21,13 +21,24 @@ defined as gpio sub-nodes of the pinmux controller. Required properties for iomux controller: - compatible: one of "rockchip,rk2928-pinctrl", "rockchip,rk3066a-pinctrl" "rockchip,rk3066b-pinctrl", "rockchip,rk3188-pinctrl" + "rockchip,rk3288-pinctrl" + - rockchip,grf: phandle referencing a syscon providing the + "general register files" + +Optional properties for iomux controller: + - rockchip,pmu: phandle referencing a syscon providing the pmu registers + as some SoCs carry parts of the iomux controller registers there. + Required for at least rk3188 and rk3288. + +Deprecated properties for iomux controller: - reg: first element is the general register space of the iomux controller - second element is the separate pull register space of the rk3188 + It should be large enough to contain also separate pull registers. + second element is the separate pull register space of the rk3188. + Use rockchip,grf and rockchip,pmu described above instead. Required properties for gpio sub nodes: - - compatible: "rockchip,gpio-bank", "rockchip,rk3188-gpio-bank0" + - compatible: "rockchip,gpio-bank" - reg: register of the gpio bank (different than the iomux registerset) - second element: separate pull register for rk3188 bank0 - interrupts: base interrupt of the gpio bank in the interrupt controller - clocks: clock that drives this bank - gpio-controller: identifies the node as a gpio controller and pin bank. @@ -39,10 +50,15 @@ Required properties for gpio sub nodes: cells should use the standard two-cell scheme described in bindings/interrupt-controller/interrupts.txt +Deprecated properties for gpio sub nodes: + - compatible: "rockchip,rk3188-gpio-bank0" + - reg: second element: separate pull register for rk3188 bank0, use + rockchip,pmu described above instead + Required properties for pin configuration node: - rockchip,pins: 3 integers array, represents a group of pins mux and config setting. The format is rockchip,pins = <PIN_BANK PIN_BANK_IDX MUX &phandle>. - The MUX 0 means gpio and MUX 1 to 3 mean the specific device function. + The MUX 0 means gpio and MUX 1 to N mean the specific device function. The phandle of a node containing the generic pinconfig options to use, as described in pinctrl-bindings.txt in this directory. @@ -54,7 +70,8 @@ Examples: pinctrl@20008000 { compatible = "rockchip,rk3066a-pinctrl"; - reg = <0x20008000 0x150>; + rockchip,grf = <&grf>; + #address-cells = <1>; #size-cells = <1>; ranges; @@ -103,16 +120,15 @@ Example for rk3188: pinctrl@20008000 { compatible = "rockchip,rk3188-pinctrl"; - reg = <0x20008000 0xa0>, - <0x20008164 0x1a0>; + rockchip,grf = <&grf>; + rockchip,pmu = <&pmu>; #address-cells = <1>; #size-cells = <1>; ranges; gpio0: gpio0@0x2000a000 { compatible = "rockchip,rk3188-gpio-bank0"; - reg = <0x2000a000 0x100>, - <0x20004064 0x8>; + reg = <0x2000a000 0x100>; interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clk_gates8 9>; diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt index 257677de3e6b..e82aaf492517 100644 --- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt @@ -16,6 +16,7 @@ Required Properties: - "samsung,exynos4210-pinctrl": for Exynos4210 compatible pin-controller. - "samsung,exynos4x12-pinctrl": for Exynos4x12 compatible pin-controller. - "samsung,exynos5250-pinctrl": for Exynos5250 compatible pin-controller. + - "samsung,exynos5260-pinctrl": for Exynos5260 compatible pin-controller. - "samsung,exynos5420-pinctrl": for Exynos5420 compatible pin-controller. - reg: Base address of the pin controller hardware module and length of @@ -43,7 +44,11 @@ Required Properties: - Pin mux/config groups as child nodes: The pin mux (selecting pin function mode) and pin config (pull up/down, driver strength) settings are represented as child nodes of the pin-controller node. There should be atleast one - child node and there is no limit on the count of these child nodes. + child node and there is no limit on the count of these child nodes. It is + also possible for a child node to consist of several further child nodes + to allow grouping multiple pinctrl groups into one. The format of second + level child nodes is exactly the same as for first level ones and is + described below. The child node should contain a list of pin(s) on which a particular pin function selection or pin configuration (or both) have to applied. This @@ -70,6 +75,7 @@ Required Properties: "samsung,pins" property of the child node. The following pin configuration properties are supported. + - samsung,pin-val: Initial value of pin output buffer. - samsung,pin-pud: Pull up/down configuration. - samsung,pin-drv: Drive strength configuration. - samsung,pin-pud-pdn: Pull up/down configuration in power down mode. @@ -248,6 +254,23 @@ Example 1: A pin-controller node with pin groups. samsung,pin-pud = <3>; samsung,pin-drv = <0>; }; + + sd4_bus8: sd4-bus-width8 { + part-1 { + samsung,pins = "gpk0-3", "gpk0-4", + "gpk0-5", "gpk0-6"; + samsung,pin-function = <3>; + samsung,pin-pud = <3>; + samsung,pin-drv = <3>; + }; + part-2 { + samsung,pins = "gpk1-3", "gpk1-4", + "gpk1-5", "gpk1-6"; + samsung,pin-function = <4>; + samsung,pin-pud = <4>; + samsung,pin-drv = <3>; + }; + }; }; Example 2: A pin-controller node with external wakeup interrupt controller node. diff --git a/Documentation/devicetree/bindings/pinctrl/ti,omap-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/ti,omap-pinctrl.txt new file mode 100644 index 000000000000..88c80273da91 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/ti,omap-pinctrl.txt @@ -0,0 +1,13 @@ +OMAP Pinctrl definitions + +Required properties: +- compatible : Should be one of: + "ti,omap2420-padconf" - OMAP2420 compatible pinctrl + "ti,omap2430-padconf" - OMAP2430 compatible pinctrl + "ti,omap3-padconf" - OMAP3 compatible pinctrl + "ti,omap4-padconf" - OMAP4 compatible pinctrl + "ti,omap5-padconf" - OMAP5 compatible pinctrl + "ti,dra7-padconf" - DRA7 compatible pinctrl + "ti,am437-padconf" - AM437x compatible pinctrl + +See Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt for further details. diff --git a/Documentation/devicetree/bindings/power/bq2415x.txt b/Documentation/devicetree/bindings/power/bq2415x.txt new file mode 100644 index 000000000000..d0327f0b59ad --- /dev/null +++ b/Documentation/devicetree/bindings/power/bq2415x.txt @@ -0,0 +1,47 @@ +Binding for TI bq2415x Li-Ion Charger + +Required properties: +- compatible: Should contain one of the following: + * "ti,bq24150" + * "ti,bq24150" + * "ti,bq24150a" + * "ti,bq24151" + * "ti,bq24151a" + * "ti,bq24152" + * "ti,bq24153" + * "ti,bq24153a" + * "ti,bq24155" + * "ti,bq24156" + * "ti,bq24156a" + * "ti,bq24158" +- reg: integer, i2c address of the device. +- ti,current-limit: integer, initial maximum current charger can pull + from power supply in mA. +- ti,weak-battery-voltage: integer, weak battery voltage threshold in mV. + The chip will use slow precharge if battery voltage + is below this value. +- ti,battery-regulation-voltage: integer, maximum charging voltage in mV. +- ti,charge-current: integer, maximum charging current in mA. +- ti,termination-current: integer, charge will be terminated when current in + constant-voltage phase drops below this value (in mA). +- ti,resistor-sense: integer, value of sensing resistor in milliohm. + +Optional properties: +- ti,usb-charger-detection: phandle to usb charger detection device. + (required for auto mode) + +Example from Nokia N900: + +bq24150a { + compatible = "ti,bq24150a"; + reg = <0x6b>; + + ti,current-limit = <100>; + ti,weak-battery-voltage = <3400>; + ti,battery-regulation-voltage = <4200>; + ti,charge-current = <650>; + ti,termination-current = <100>; + ti,resistor-sense = <68>; + + ti,usb-charger-detection = <&isp1704>; +}; diff --git a/Documentation/devicetree/bindings/power/power-controller.txt b/Documentation/devicetree/bindings/power/power-controller.txt new file mode 100644 index 000000000000..4f7a3bc9c407 --- /dev/null +++ b/Documentation/devicetree/bindings/power/power-controller.txt @@ -0,0 +1,18 @@ +* Generic system power control capability + +Power-management integrated circuits or miscellaneous hardware components are +sometimes able to control the system power. The device driver associated with these +components might need to define this capability, which tells the kernel that +it can be used to switch off the system. The corresponding device must have the +standard property "system-power-controller" in its device node. This property +marks the device as able to control the system power. In order to test if this +property is found programmatically, use the helper function +"of_device_is_system_power_controller" from of.h . + +Example: + +act8846: act8846@5 { + compatible = "active-semi,act8846"; + status = "okay"; + system-power-controller; +} diff --git a/Documentation/devicetree/bindings/power/power_domain.txt b/Documentation/devicetree/bindings/power/power_domain.txt new file mode 100644 index 000000000000..98c16672ab5f --- /dev/null +++ b/Documentation/devicetree/bindings/power/power_domain.txt @@ -0,0 +1,49 @@ +* Generic PM domains + +System on chip designs are often divided into multiple PM domains that can be +used for power gating of selected IP blocks for power saving by reduced leakage +current. + +This device tree binding can be used to bind PM domain consumer devices with +their PM domains provided by PM domain providers. A PM domain provider can be +represented by any node in the device tree and can provide one or more PM +domains. A consumer node can refer to the provider by a phandle and a set of +phandle arguments (so called PM domain specifiers) of length specified by the +#power-domain-cells property in the PM domain provider node. + +==PM domain providers== + +Required properties: + - #power-domain-cells : Number of cells in a PM domain specifier; + Typically 0 for nodes representing a single PM domain and 1 for nodes + providing multiple PM domains (e.g. power controllers), but can be any value + as specified by device tree binding documentation of particular provider. + +Example: + + power: power-controller@12340000 { + compatible = "foo,power-controller"; + reg = <0x12340000 0x1000>; + #power-domain-cells = <1>; + }; + +The node above defines a power controller that is a PM domain provider and +expects one cell as its phandle argument. + +==PM domain consumers== + +Required properties: + - power-domains : A phandle and PM domain specifier as defined by bindings of + the power controller specified by phandle. + +Example: + + leaky-device@12350000 { + compatible = "foo,i-leak-current"; + reg = <0x12350000 0x1000>; + power-domains = <&power 0>; + }; + +The node above defines a typical PM domain consumer device, which is located +inside a PM domain with index 0 of a power controller represented by a node +with the label "power". diff --git a/Documentation/devicetree/bindings/power/reset/keystone-reset.txt b/Documentation/devicetree/bindings/power/reset/keystone-reset.txt new file mode 100644 index 000000000000..c82f12e2d85c --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/keystone-reset.txt @@ -0,0 +1,67 @@ +* Device tree bindings for Texas Instruments keystone reset + +This node is intended to allow SoC reset in case of software reset +of selected watchdogs. + +The Keystone SoCs can contain up to 4 watchdog timers to reset +SoC. Each watchdog timer event input is connected to the Reset Mux +block. The Reset Mux block can be configured to cause reset or not. + +Additionally soft or hard reset can be configured. + +Required properties: + +- compatible: ti,keystone-reset + +- ti,syscon-pll: phandle/offset pair. The phandle to syscon used to + access pll controller registers and the offset to use + reset control registers. + +- ti,syscon-dev: phandle/offset pair. The phandle to syscon used to + access device state control registers and the offset + in order to use mux block registers for all watchdogs. + +Optional properties: + +- ti,soft-reset: Boolean option indicating soft reset. + By default hard reset is used. + +- ti,wdt-list: WDT list that can cause SoC reset. It's not related + to WDT driver, it's just needed to enable a SoC related + reset that's triggered by one of WDTs. The list is + in format: <0>, <2>; It can be in random order and + begins from 0 to 3, as keystone can contain up to 4 SoC + reset watchdogs and can be in random order. + +Example 1: +Setup keystone reset so that in case software reset or +WDT0 is triggered it issues hard reset for SoC. + +pllctrl: pll-controller@02310000 { + compatible = "ti,keystone-pllctrl", "syscon"; + reg = <0x02310000 0x200>; +}; + +devctrl: device-state-control@02620000 { + compatible = "ti,keystone-devctrl", "syscon"; + reg = <0x02620000 0x1000>; +}; + +rstctrl: reset-controller { + compatible = "ti,keystone-reset"; + ti,syscon-pll = <&pllctrl 0xe4>; + ti,syscon-dev = <&devctrl 0x328>; + ti,wdt-list = <0>; +}; + +Example 2: +Setup keystone reset so that in case of software reset or +WDT0 or WDT2 is triggered it issues soft reset for SoC. + +rstctrl: reset-controller { + compatible = "ti,keystone-reset"; + ti,syscon-pll = <&pllctrl 0xe4>; + ti,syscon-dev = <&devctrl 0x328>; + ti,wdt-list = <0>, <2>; + ti,soft-reset; +}; diff --git a/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt b/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt new file mode 100644 index 000000000000..0c94c637f63b --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt @@ -0,0 +1,26 @@ +Binding for the LTC2952 PowerPath controller + +This chip is used to externally trigger a system shut down. Once the trigger has +been sent, the chips' watchdog has to be reset to gracefully shut down. +If the Linux systems decides to shut down it powers off the platform via the +kill signal. + +Required properties: + +- compatible: Must contain: "lltc,ltc2952" +- trigger-gpios: phandle + gpio-specifier for the GPIO connected to the + chip's trigger line +- watchdog-gpios: phandle + gpio-specifier for the GPIO connected to the + chip's watchdog line +- kill-gpios: phandle + gpio-specifier for the GPIO connected to the + chip's kill line + +Example: + +ltc2952 { + compatible = "lltc,ltc2952"; + + trigger-gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; + watchdog-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; + kill-gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; +}; diff --git a/Documentation/devicetree/bindings/power/reset/st-reset.txt b/Documentation/devicetree/bindings/power/reset/st-reset.txt new file mode 100644 index 000000000000..809af54f02f3 --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/st-reset.txt @@ -0,0 +1,11 @@ +*Device-Tree bindings for ST SW reset functionality + +Required properties: +- compatible: should be "st,<chip>-restart". +- st,syscfg: should be a phandle of the syscfg node. + +Example node: + restart { + compatible = "st,stih416-restart"; + st,syscfg = <&syscfg_sbc>; + }; diff --git a/Documentation/devicetree/bindings/power/reset/syscon-reboot.txt b/Documentation/devicetree/bindings/power/reset/syscon-reboot.txt new file mode 100644 index 000000000000..11906316b43d --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/syscon-reboot.txt @@ -0,0 +1,23 @@ +Generic SYSCON mapped register reset driver + +This is a generic reset driver using syscon to map the reset register. +The reset is generally performed with a write to the reset register +defined by the register map pointed by syscon reference plus the offset +with the mask defined in the reboot node. + +Required properties: +- compatible: should contain "syscon-reboot" +- regmap: this is phandle to the register map node +- offset: offset in the register map for the reboot register (in bytes) +- mask: the reset value written to the reboot register (32 bit access) + +Default will be little endian mode, 32 bit access only. + +Examples: + + reboot { + compatible = "syscon-reboot"; + regmap = <®mapnode>; + offset = <0x0>; + mask = <0x1>; + }; diff --git a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt new file mode 100644 index 000000000000..6fbf6e7ecde6 --- /dev/null +++ b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt @@ -0,0 +1,83 @@ +Rockchip SRAM for IO Voltage Domains: +------------------------------------- + +IO domain voltages on some Rockchip SoCs are variable but need to be +kept in sync between the regulators and the SoC using a special +register. + +A specific example using rk3288: +- If the regulator hooked up to a pin like SDMMC0_VDD is 3.3V then + bit 7 of GRF_IO_VSEL needs to be 0. If the regulator hooked up to + that same pin is 1.8V then bit 7 of GRF_IO_VSEL needs to be 1. + +Said another way, this driver simply handles keeping bits in the SoC's +general register file (GRF) in sync with the actual value of a voltage +hooked up to the pins. + +Note that this driver specifically doesn't include: +- any logic for deciding what voltage we should set regulators to +- any logic for deciding whether regulators (or internal SoC blocks) + should have power or not have power + +If there were some other software that had the smarts of making +decisions about regulators, it would work in conjunction with this +driver. When that other software adjusted a regulator's voltage then +this driver would handle telling the SoC about it. A good example is +vqmmc for SD. In that case the dw_mmc driver simply is told about a +regulator. It changes the regulator between 3.3V and 1.8V at the +right time. This driver notices the change and makes sure that the +SoC is on the same page. + + +Required properties: +- compatible: should be one of: + - "rockchip,rk3188-io-voltage-domain" for rk3188 + - "rockchip,rk3288-io-voltage-domain" for rk3288 +- rockchip,grf: phandle to the syscon managing the "general register files" + + +You specify supplies using the standard regulator bindings by including +a phandle the the relevant regulator. All specified supplies must be able +to report their voltage. The IO Voltage Domain for any non-specified +supplies will be not be touched. + +Possible supplies for rk3188: +- ap0-supply: The supply connected to AP0_VCC. +- ap1-supply: The supply connected to AP1_VCC. +- cif-supply: The supply connected to CIF_VCC. +- flash-supply: The supply connected to FLASH_VCC. +- lcdc0-supply: The supply connected to LCD0_VCC. +- lcdc1-supply: The supply connected to LCD1_VCC. +- vccio0-supply: The supply connected to VCCIO0. +- vccio1-supply: The supply connected to VCCIO1. + Sometimes also labeled VCCIO1 and VCCIO2. + +Possible supplies for rk3288: +- audio-supply: The supply connected to APIO4_VDD. +- bb-supply: The supply connected to APIO5_VDD. +- dvp-supply: The supply connected to DVPIO_VDD. +- flash0-supply: The supply connected to FLASH0_VDD. Typically for eMMC +- flash1-supply: The supply connected to FLASH1_VDD. Also known as SDIO1. +- gpio30-supply: The supply connected to APIO1_VDD. +- gpio1830 The supply connected to APIO2_VDD. +- lcdc-supply: The supply connected to LCDC_VDD. +- sdcard-supply: The supply connected to SDMMC0_VDD. +- wifi-supply: The supply connected to APIO3_VDD. Also known as SDIO0. + + +Example: + + io-domains { + compatible = "rockchip,rk3288-io-voltage-domain"; + rockchip,grf = <&grf>; + + audio-supply = <&vcc18_codec>; + bb-supply = <&vcc33_io>; + dvp-supply = <&vcc_18>; + flash0-supply = <&vcc18_flashio>; + gpio1830-supply = <&vcc33_io>; + gpio30-supply = <&vcc33_pmuio>; + lcdc-supply = <&vcc33_lcd>; + sdcard-supply = <&vccio_sd>; + wifi-supply = <&vcc18_wl>; + }; diff --git a/Documentation/devicetree/bindings/power/rx51-battery.txt b/Documentation/devicetree/bindings/power/rx51-battery.txt new file mode 100644 index 000000000000..90438453db58 --- /dev/null +++ b/Documentation/devicetree/bindings/power/rx51-battery.txt @@ -0,0 +1,25 @@ +Binding for Nokia N900 battery + +The Nokia N900 battery status can be read via the TWL4030's A/D converter. + +Required properties: +- compatible: Should contain one of the following: + * "nokia,n900-battery" +- io-channels: Should contain IIO channel specifiers + for each element in io-channel-names. +- io-channel-names: Should contain the following values: + * "temp" - The ADC channel for temperature reading + * "bsi" - The ADC channel for battery size identification + * "vbat" - The ADC channel to measure the battery voltage + +Example from Nokia N900: + +battery: n900-battery { + compatible = "nokia,n900-battery"; + io-channels = <&twl4030_madc 0>, + <&twl4030_madc 4>, + <&twl4030_madc 12>; + io-channel-names = "temp", + "bsi", + "vbat"; +}; diff --git a/Documentation/devicetree/bindings/power_supply/axxia-reset.txt b/Documentation/devicetree/bindings/power_supply/axxia-reset.txt new file mode 100644 index 000000000000..47e720d249d2 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/axxia-reset.txt @@ -0,0 +1,20 @@ +Axxia Restart Driver + +This driver can do reset of the Axxia SoC. It uses the registers in the syscon +block to initiate a chip reset. + +Required Properties: + -compatible: "lsi,axm55xx-reset" + -syscon: phandle to the syscon node. + +Example: + + syscon: syscon@2010030000 { + compatible = "lsi,axxia-syscon", "syscon"; + reg = <0x20 0x10030000 0 0x2000>; + }; + + reset: reset@2010031000 { + compatible = "lsi,axm55xx-reset"; + syscon = <&syscon>; + }; diff --git a/Documentation/devicetree/bindings/power_supply/charger-manager.txt b/Documentation/devicetree/bindings/power_supply/charger-manager.txt index 2b33750e3db2..ec4fe9de3137 100644 --- a/Documentation/devicetree/bindings/power_supply/charger-manager.txt +++ b/Documentation/devicetree/bindings/power_supply/charger-manager.txt @@ -24,7 +24,7 @@ Optional properties : - cm-thermal-zone : name of external thermometer's thermal zone - cm-battery-* : threshold battery temperature for charging -cold : critical cold temperature of battery for charging - -cold-in-minus : flag that cold temerature is in minus degree + -cold-in-minus : flag that cold temperature is in minus degrees -hot : critical hot temperature of battery for charging -temp-diff : temperature difference to allow recharging - cm-dis/charging-max = limits of charging duration diff --git a/Documentation/devicetree/bindings/power_supply/imx-snvs-poweroff.txt b/Documentation/devicetree/bindings/power_supply/imx-snvs-poweroff.txt new file mode 100644 index 000000000000..dc7c9bad63ea --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/imx-snvs-poweroff.txt @@ -0,0 +1,23 @@ +i.mx6 Poweroff Driver + +SNVS_LPCR in SNVS module can power off the whole system by pull +PMIC_ON_REQ low if PMIC_ON_REQ is connected with external PMIC. +If you don't want to use PMIC_ON_REQ as power on/off control, +please set status='disabled' to disable this driver. + +Required Properties: +-compatible: "fsl,sec-v4.0-poweroff" +-reg: Specifies the physical address of the SNVS_LPCR register + +Example: + snvs@020cc000 { + compatible = "fsl,sec-v4.0-mon", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x020cc000 0x4000>; + ..... + snvs_poweroff: snvs-poweroff@38 { + compatible = "fsl,sec-v4.0-poweroff"; + reg = <0x38 0x4>; + }; + } diff --git a/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt b/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt index 0347d8350d94..af25e77c0e0c 100644 --- a/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt +++ b/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt @@ -6,8 +6,11 @@ Orion5x SoCs. Sending the character 'A', at 19200 baud, tells the microcontroller to turn the power off. This driver adds a handler to pm_power_off which is called to turn the power off. +Synology NAS devices use a similar scheme, but a different baud rate, +9600, and a different character, '1'. + Required Properties: -- compatible: Should be "qnap,power-off" +- compatible: Should be "qnap,power-off" or "synology,power-off" - reg: Address and length of the register set for UART1 - clocks: tclk clock diff --git a/Documentation/devicetree/bindings/powerpc/4xx/akebono.txt b/Documentation/devicetree/bindings/powerpc/4xx/akebono.txt new file mode 100644 index 000000000000..db939210e29d --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/4xx/akebono.txt @@ -0,0 +1,54 @@ + +IBM Akebono board device tree +============================= + +The IBM Akebono board is a development board for the PPC476GTR SoC. + +0) The root node + + Required properties: + + - model : "ibm,akebono". + - compatible : "ibm,akebono" , "ibm,476gtr". + +1.a) The Secure Digital Host Controller Interface (SDHCI) node + + Represent the Secure Digital Host Controller Interfaces. + + Required properties: + + - compatible : should be "ibm,476gtr-sdhci","generic-sdhci". + - reg : should contain the SDHCI registers location and length. + - interrupt-parent : a phandle for the interrupt controller. + - interrupts : should contain the SDHCI interrupt. + +1.b) The Advanced Host Controller Interface (AHCI) SATA node + + Represents the advanced host controller SATA interface. + + Required properties: + + - compatible : should be "ibm,476gtr-ahci". + - reg : should contain the AHCI registers location and length. + - interrupt-parent : a phandle for the interrupt controller. + - interrupts : should contain the AHCI interrupt. + +1.c) The FPGA node + + The Akebono board stores some board information such as the revision + number in an FPGA which is represented by this node. + + Required properties: + + - compatible : should be "ibm,akebono-fpga". + - reg : should contain the FPGA registers location and length. + +1.d) The AVR node + + The Akebono board has an Atmel AVR microprocessor attached to the I2C + bus as a power controller for the board. + + Required properties: + + - compatible : should be "ibm,akebono-avr". + - reg : should contain the I2C bus address for the AVR. diff --git a/Documentation/devicetree/bindings/powerpc/4xx/hsta.txt b/Documentation/devicetree/bindings/powerpc/4xx/hsta.txt new file mode 100644 index 000000000000..c737c8338705 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/4xx/hsta.txt @@ -0,0 +1,19 @@ + +ppc476gtr High Speed Serial Assist (HSTA) node +============================================== + +The 476gtr SoC contains a high speed serial assist module attached +between the plb4 and plb6 system buses to provide high speed data +transfer between memory and system peripherals as well as support for +PCI message signalled interrupts. + +Currently only the MSI support is used by Linux using the following +device tree entries: + +Require properties: +- compatible : "ibm,476gtr-hsta-msi", "ibm,hsta-msi" +- reg : register mapping for the HSTA MSI space +- interrupt-parent : parent controller for mapping interrupts +- interrupts : ordered interrupt mapping for each MSI in the register + space. The first interrupt should be associated with a + register offset of 0x00, the second to 0x10, etc. diff --git a/Documentation/devicetree/bindings/powerpc/4xx/reboot.txt b/Documentation/devicetree/bindings/powerpc/4xx/reboot.txt index d7217260589c..5bc63551319e 100644 --- a/Documentation/devicetree/bindings/powerpc/4xx/reboot.txt +++ b/Documentation/devicetree/bindings/powerpc/4xx/reboot.txt @@ -1,7 +1,7 @@ Reboot property to control system reboot on PPC4xx systems: By setting "reset_type" to one of the following values, the default -software reset mechanism may be overidden. Here the possible values of +software reset mechanism may be overridden. Here the possible values of "reset_type": 1 - PPC4xx core reset diff --git a/Documentation/devicetree/bindings/powerpc/fsl/board.txt b/Documentation/devicetree/bindings/powerpc/fsl/board.txt index 380914e965e0..cff38bdbc0e4 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/board.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/board.txt @@ -67,3 +67,36 @@ Example: gpio-controller; }; }; + +* Freescale on-board FPGA connected on I2C bus + +Some Freescale boards like BSC9132QDS have on board FPGA connected on +the i2c bus. + +Required properties: +- compatible: Should be a board-specific string followed by a string + indicating the type of FPGA. Example: + "fsl,<board>-fpga", "fsl,fpga-qixis-i2c" +- reg: Should contain the address of the FPGA + +Example: + fpga: fpga@66 { + compatible = "fsl,bsc9132qds-fpga", "fsl,fpga-qixis-i2c"; + reg = <0x66>; + }; + +* Freescale on-board CPLD + +Some Freescale boards like T1040RDB have an on board CPLD connected. + +Required properties: +- compatible: Should be a board-specific string like "fsl,<board>-cpld" + Example: + "fsl,t1040rdb-cpld", "fsl,t1042rdb-cpld", "fsl,t1042rdb_pi-cpld" +- reg: should describe CPLD registers + +Example: + cpld@3,0 { + compatible = "fsl,t1040rdb-cpld"; + reg = <3 0 0x300>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/ccf.txt b/Documentation/devicetree/bindings/powerpc/fsl/ccf.txt new file mode 100644 index 000000000000..454da7e08acd --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/ccf.txt @@ -0,0 +1,46 @@ +Freescale CoreNet Coherency Fabric(CCF) Device Tree Binding + +DESCRIPTION + +The CoreNet coherency fabric is a fabric-oriented, connectivity infrastructure +that enables the implementation of coherent, multicore systems. + +Required properties: + +- compatible: <string list> + fsl,corenet1-cf - CoreNet coherency fabric version 1. + Example chips: T4240, B4860 + + fsl,corenet2-cf - CoreNet coherency fabric version 2. + Example chips: P5040, P5020, P4080, P3041, P2041 + + fsl,corenet-cf - Used to represent the common registers + between CCF version 1 and CCF version 2. This compatible + is retained for compatibility reasons, as it was already + used for both CCF version 1 chips and CCF version 2 + chips. It should be specified after either + "fsl,corenet1-cf" or "fsl,corenet2-cf". + +- reg: <prop-encoded-array> + A standard property. Represents the CCF registers. + +- interrupts: <prop-encoded-array> + Interrupt mapping for CCF error interrupt. + +- fsl,ccf-num-csdids: <u32> + Specifies the number of Coherency Subdomain ID Port Mapping + Registers that are supported by the CCF. + +- fsl,ccf-num-snoopids: <u32> + Specifies the number of Snoop ID Port Mapping Registers that + are supported by CCF. + +Example: + + corenet-cf@18000 { + compatible = "fsl,corenet2-cf", "fsl,corenet-cf"; + reg = <0x18000 0x1000>; + interrupts = <16 2 1 31>; + fsl,ccf-num-csdids = <32>; + fsl,ccf-num-snoopids = <32>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpus.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpus.txt index 922c30ad90d1..f8cd2397aa04 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/cpus.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpus.txt @@ -20,3 +20,14 @@ PROPERTIES a property named fsl,eref-[CAT], where [CAT] is the abbreviated category name with all uppercase letters converted to lowercase, indicates that the category is supported by the implementation. + + - fsl,portid-mapping + Usage: optional + Value type: <u32> + Definition: The Coherency Subdomain ID Port Mapping Registers and + Snoop ID Port Mapping registers, which are part of the CoreNet + Coherency fabric (CCF), provide a CoreNet Coherency Subdomain + ID/CoreNet Snoop ID to cpu mapping functions. Certain bits from + these registers should be set if the coresponding CPU should be + snooped. This property defines a bitmask which selects the bit + that should be set if this cpu should be snooped. diff --git a/Documentation/devicetree/bindings/powerpc/fsl/dcsr.txt b/Documentation/devicetree/bindings/powerpc/fsl/dcsr.txt index 9d54eb5a295f..18a88100af94 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/dcsr.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/dcsr.txt @@ -82,7 +82,7 @@ PROPERTIES Which event source asserted the interrupt is captured in an EPU Interrupt Status Register (EPISR0,EPISR1). - Interrupt numbers are lised in order (perfmon, event0, event1). + Interrupt numbers are listed in order (perfmon, event0, event1). - interrupt-parent Usage: required diff --git a/Documentation/devicetree/bindings/powerpc/fsl/l2cache.txt b/Documentation/devicetree/bindings/powerpc/fsl/l2cache.txt new file mode 100644 index 000000000000..c41b2187eaa8 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/l2cache.txt @@ -0,0 +1,23 @@ +Freescale L2 Cache Controller + +L2 cache is present in Freescale's QorIQ and QorIQ Qonverge platforms. +The cache bindings explained below are ePAPR compliant + +Required Properties: + +- compatible : Should include "fsl,chip-l2-cache-controller" and "cache" + where chip is the processor (bsc9132, npc8572 etc.) +- reg : Address and size of L2 cache controller registers +- cache-size : Size of the entire L2 cache +- interrupts : Error interrupt of L2 controller +- cache-line-size : Size of L2 cache lines + +Example: + + L2: l2-cache-controller@20000 { + compatible = "fsl,bsc9132-l2-cache-controller", "cache"; + reg = <0x20000 0x1000>; + cache-line-size = <32>; // 32 bytes + cache-size = <0x40000>; // L2,256K + interrupts = <16 2 1 0>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mem-ctrlr.txt b/Documentation/devicetree/bindings/powerpc/fsl/mem-ctrlr.txt new file mode 100644 index 000000000000..f87856faf1ab --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mem-ctrlr.txt @@ -0,0 +1,27 @@ +Freescale DDR memory controller + +Properties: + +- compatible : Should include "fsl,chip-memory-controller" where + chip is the processor (bsc9132, mpc8572 etc.), or + "fsl,qoriq-memory-controller". +- reg : Address and size of DDR controller registers +- interrupts : Error interrupt of DDR controller + +Example 1: + + memory-controller@2000 { + compatible = "fsl,bsc9132-memory-controller"; + reg = <0x2000 0x1000>; + interrupts = <16 2 1 8>; + }; + + +Example 2: + + ddr1: memory-controller@8000 { + compatible = "fsl,qoriq-memory-controller-v4.7", + "fsl,qoriq-memory-controller"; + reg = <0x8000 0x1000>; + interrupts = <16 2 1 23>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/pamu.txt b/Documentation/devicetree/bindings/powerpc/fsl/pamu.txt index 1f5e329f756c..c2b2899885f2 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/pamu.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/pamu.txt @@ -34,6 +34,15 @@ Optional properties: for legacy drivers. - interrupt-parent : <phandle> Phandle to interrupt controller +- fsl,portid-mapping : <u32> + The Coherency Subdomain ID Port Mapping Registers and + Snoop ID Port Mapping registers, which are part of the + CoreNet Coherency fabric (CCF), provide a CoreNet + Coherency Subdomain ID/CoreNet Snoop ID to pamu mapping + functions. Certain bits from these registers should be + set if PAMUs should be snooped. This property defines + a bitmask which selects the bits that should be set if + PAMUs should be snooped. Child nodes: @@ -88,6 +97,7 @@ Example: compatible = "fsl,pamu-v1.0", "fsl,pamu"; reg = <0x20000 0x5000>; ranges = <0 0x20000 0x5000>; + fsl,portid-mapping = <0xf80000>; #address-cells = <1>; #size-cells = <1>; interrupts = < diff --git a/Documentation/devicetree/bindings/pwm/bcm-kona-pwm.txt b/Documentation/devicetree/bindings/pwm/bcm-kona-pwm.txt new file mode 100644 index 000000000000..8eae9fe7841c --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/bcm-kona-pwm.txt @@ -0,0 +1,21 @@ +Broadcom Kona PWM controller device tree bindings + +This controller has 6 channels. + +Required Properties : +- compatible: should contain "brcm,kona-pwm" +- reg: physical base address and length of the controller's registers +- clocks: phandle + clock specifier pair for the external clock +- #pwm-cells: Should be 3. See pwm.txt in this directory for a + description of the cells format. + +Refer to clocks/clock-bindings.txt for generic clock consumer properties. + +Example: + +pwm: pwm@3e01a000 { + compatible = "brcm,bcm11351-pwm", "brcm,kona-pwm"; + reg = <0x3e01a000 0xc4>; + clocks = <&pwm_clk>; + #pwm-cells = <3>; +}; diff --git a/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt b/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt new file mode 100644 index 000000000000..a183db48f910 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt @@ -0,0 +1,16 @@ +* Cirris Logic CLPS711X PWM controller + +Required properties: +- compatible: Shall contain "cirrus,clps711x-pwm". +- reg: Physical base address and length of the controller's registers. +- clocks: phandle + clock specifier pair of the PWM reference clock. +- #pwm-cells: Should be 1. The cell specifies the index of the channel. + +Example: + pwm: pwm@80000400 { + compatible = "cirrus,ep7312-pwm", + "cirrus,clps711x-pwm"; + reg = <0x80000400 0x4>; + clocks = <&clks 8>; + #pwm-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt b/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt new file mode 100644 index 000000000000..3899d6a557c1 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt @@ -0,0 +1,52 @@ +Freescale FlexTimer Module (FTM) PWM controller + +The same FTM PWM device can have a different endianness on different SoCs. The +device tree provides a property to describing this so that an operating system +device driver can handle all variants of the device. Refer to the table below +for the endianness of the FTM PWM block as integrated into the existing SoCs: + + SoC | FTM-PWM endianness + --------+------------------- + Vybrid | LE + LS1 | BE + LS2 | LE + +Please see ../regmap/regmap.txt for more detail about how to specify endian +modes in device tree. + + +Required properties: +- compatible: Should be "fsl,vf610-ftm-pwm". +- reg: Physical base address and length of the controller's registers +- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of + the cells format. +- clock-names: Should include the following module clock source entries: + "ftm_sys" (module clock, also can be used as counter clock), + "ftm_ext" (external counter clock), + "ftm_fix" (fixed counter clock), + "ftm_cnt_clk_en" (external and fixed counter clock enable/disable). +- clocks: Must contain a phandle and clock specifier for each entry in + clock-names, please see clock/clock-bindings.txt for details of the property + values. +- pinctrl-names: Must contain a "default" entry. +- pinctrl-NNN: One property must exist for each entry in pinctrl-names. + See pinctrl/pinctrl-bindings.txt for details of the property values. +- big-endian: Boolean property, required if the FTM PWM registers use a big- + endian rather than little-endian layout. + +Example: + +pwm0: pwm@40038000 { + compatible = "fsl,vf610-ftm-pwm"; + reg = <0x40038000 0x1000>; + #pwm-cells = <3>; + clock-names = "ftm_sys", "ftm_ext", + "ftm_fix", "ftm_cnt_clk_en"; + clocks = <&clks VF610_CLK_FTM0>, + <&clks VF610_CLK_FTM0_EXT_SEL>, + <&clks VF610_CLK_FTM0_FIX_SEL>, + <&clks VF610_CLK_FTM0_EXT_FIX_EN>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm0_1>; + big-endian; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt b/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt new file mode 100644 index 000000000000..b8be3d09ee26 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt @@ -0,0 +1,20 @@ +Rockchip PWM controller + +Required properties: + - compatible: should be "rockchip,<name>-pwm" + "rockchip,rk2928-pwm": found on RK29XX,RK3066 and RK3188 SoCs + "rockchip,rk3288-pwm": found on RK3288 SoC + "rockchip,vop-pwm": found integrated in VOP on RK3288 SoC + - reg: physical base address and length of the controller's registers + - clocks: phandle and clock specifier of the PWM reference clock + - #pwm-cells: must be 2 (rk2928) or 3 (rk3288). See pwm.txt in this directory + for a description of the cell format. + +Example: + + pwm0: pwm@20030000 { + compatible = "rockchip,rk2928-pwm"; + reg = <0x20030000 0x10>; + clocks = <&cru PCLK_PWM01>; + #pwm-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-st.txt b/Documentation/devicetree/bindings/pwm/pwm-st.txt new file mode 100644 index 000000000000..84d2fb807d3c --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-st.txt @@ -0,0 +1,41 @@ +STMicroelectronics PWM driver bindings +-------------------------------------- + +Required parameters: +- compatible : "st,pwm" +- #pwm-cells : Number of cells used to specify a PWM. First cell + specifies the per-chip index of the PWM to use and the + second cell is the period in nanoseconds - fixed to 2 + for STiH41x. +- reg : Physical base address and length of the controller's + registers. +- pinctrl-names: Set to "default". +- pinctrl-0: List of phandles pointing to pin configuration nodes + for PWM module. + For Pinctrl properties, please refer to [1]. +- clock-names: Set to "pwm". +- clocks: phandle of the clock used by the PWM module. + For Clk properties, please refer to [2]. + +Optional properties: +- st,pwm-num-chan: Number of available channels. If not passed, the driver + will consider single channel by default. + +[1] Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt +[2] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Example: + +pwm1: pwm@fe510000 { + compatible = "st,pwm"; + reg = <0xfe510000 0x68>; + #pwm-cells = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1_chan0_default + &pinctrl_pwm1_chan1_default + &pinctrl_pwm1_chan2_default + &pinctrl_pwm1_chan3_default>; + clocks = <&clk_sysin>; + clock-names = "pwm"; + st,pwm-num-chan = <4>; +}; diff --git a/Documentation/devicetree/bindings/regmap/regmap.txt b/Documentation/devicetree/bindings/regmap/regmap.txt new file mode 100644 index 000000000000..b494f8b8ef72 --- /dev/null +++ b/Documentation/devicetree/bindings/regmap/regmap.txt @@ -0,0 +1,47 @@ +Device-Tree binding for regmap + +The endianness mode of CPU & Device scenarios: +Index Device Endianness properties +--------------------------------------------------- +1 BE 'big-endian' +2 LE 'little-endian' + +For one device driver, which will run in different scenarios above +on different SoCs using the devicetree, we need one way to simplify +this. + +Required properties: +- {big,little}-endian: these are boolean properties, if absent + meaning that the CPU and the Device are in the same endianness mode, + these properties are for register values and all the buffers only. + +Examples: +Scenario 1 : CPU in LE mode & device in LE mode. +dev: dev@40031000 { + compatible = "name"; + reg = <0x40031000 0x1000>; + ... +}; + +Scenario 2 : CPU in LE mode & device in BE mode. +dev: dev@40031000 { + compatible = "name"; + reg = <0x40031000 0x1000>; + ... + big-endian; +}; + +Scenario 3 : CPU in BE mode & device in BE mode. +dev: dev@40031000 { + compatible = "name"; + reg = <0x40031000 0x1000>; + ... +}; + +Scenario 4 : CPU in BE mode & device in LE mode. +dev: dev@40031000 { + compatible = "name"; + reg = <0x40031000 0x1000>; + ... + little-endian; +}; diff --git a/Documentation/devicetree/bindings/regulator/act8865-regulator.txt b/Documentation/devicetree/bindings/regulator/act8865-regulator.txt index bef1fbb647ca..dad6358074ac 100644 --- a/Documentation/devicetree/bindings/regulator/act8865-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/act8865-regulator.txt @@ -1,13 +1,20 @@ -ACT8865 regulator +ACT88xx regulators ------------------- Required properties: -- compatible: "active-semi,act8865" +- compatible: "active-semi,act8846" or "active-semi,act8865" - reg: I2C slave address +Optional properties: +- system-power-controller: Telling whether or not this pmic is controlling + the system power. See Documentation/devicetree/bindings/power/power-controller.txt . + Any standard regulator properties can be used to configure the single regulator. The valid names for regulators are: + - for act8846: + REG1, REG2, REG3, REG4, REG5, REG6, REG7, REG8, REG9, REG10, REG11, REG12 + - for act8865: DCDC_REG1, DCDC_REG2, DCDC_REG3, LDO_REG1, LDO_REG2, LDO_REG3, LDO_REG4. Example: diff --git a/Documentation/devicetree/bindings/regulator/da9210.txt b/Documentation/devicetree/bindings/regulator/da9210.txt index f120f229d67d..3297c53cb915 100644 --- a/Documentation/devicetree/bindings/regulator/da9210.txt +++ b/Documentation/devicetree/bindings/regulator/da9210.txt @@ -2,7 +2,7 @@ Required properties: -- compatible: must be "diasemi,da9210" +- compatible: must be "dlg,da9210" - reg: the i2c slave address of the regulator. It should be 0x68. Any standard regulator properties can be used to configure the single da9210 @@ -11,7 +11,7 @@ DCDC. Example: da9210@68 { - compatible = "diasemi,da9210"; + compatible = "dlg,da9210"; reg = <0x68>; regulator-min-microvolt = <900000>; diff --git a/Documentation/devicetree/bindings/regulator/da9211.txt b/Documentation/devicetree/bindings/regulator/da9211.txt new file mode 100644 index 000000000000..240019a82f9a --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/da9211.txt @@ -0,0 +1,63 @@ +* Dialog Semiconductor DA9211/DA9213 Voltage Regulator + +Required properties: +- compatible: "dlg,da9211" or "dlg,da9213". +- reg: I2C slave address, usually 0x68. +- interrupts: the interrupt outputs of the controller +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name, with valid + values listed below. The content of each sub-node is defined by the + standard binding for regulators; see regulator.txt. + BUCKA and BUCKB. + +Optional properties: +- Any optional property defined in regulator.txt + +Example 1) DA9211 + + pmic: da9211@68 { + compatible = "dlg,da9211"; + reg = <0x68>; + interrupts = <3 27>; + + regulators { + BUCKA { + regulator-name = "VBUCKA"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <2000000>; + regulator-max-microamp = <5000000>; + }; + BUCKB { + regulator-name = "VBUCKB"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <2000000>; + regulator-max-microamp = <5000000>; + }; + }; + }; + +Example 2) DA92113 + pmic: da9213@68 { + compatible = "dlg,da9213"; + reg = <0x68>; + interrupts = <3 27>; + + regulators { + BUCKA { + regulator-name = "VBUCKA"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <3000000>; + regulator-max-microamp = <6000000>; + }; + BUCKB { + regulator-name = "VBUCKB"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <3000000>; + regulator-max-microamp = <6000000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/fan53555.txt b/Documentation/devicetree/bindings/regulator/fan53555.txt new file mode 100644 index 000000000000..54a3f2c80e3a --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/fan53555.txt @@ -0,0 +1,23 @@ +Binding for Fairchild FAN53555 regulators + +Required properties: + - compatible: one of "fcs,fan53555", "silergy,syr827", "silergy,syr828" + - reg: I2C address + +Optional properties: + - fcs,suspend-voltage-selector: declare which of the two available + voltage selector registers should be used for the suspend + voltage. The other one is used for the runtime voltage setting + Possible values are either <0> or <1> + - vin-supply: regulator supplying the vin pin + +Example: + + regulator@40 { + compatible = "fcs,fan53555"; + regulator-name = "fan53555"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&parent_reg>; + fcs,suspend-voltage-selector = <1>; + }; diff --git a/Documentation/devicetree/bindings/regulator/gpio-regulator.txt b/Documentation/devicetree/bindings/regulator/gpio-regulator.txt index 63c659800c03..e5cac1e0ca8a 100644 --- a/Documentation/devicetree/bindings/regulator/gpio-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/gpio-regulator.txt @@ -8,8 +8,12 @@ Required properties: Optional properties: - enable-gpio : GPIO to use to enable/disable the regulator. - gpios : GPIO group used to control voltage. +- gpios-states : gpios pin's initial states array. 0: LOW, 1: HIGH. + defualt is LOW if nothing is specified. - startup-delay-us : Startup time in microseconds. - enable-active-high : Polarity of GPIO is active high (default is low). +- regulator-type : Specifies what is being regulated, must be either + "voltage" or "current", defaults to current. Any property defined as part of the core regulator binding defined in regulator.txt can also be used. diff --git a/Documentation/devicetree/bindings/regulator/isl9305.txt b/Documentation/devicetree/bindings/regulator/isl9305.txt new file mode 100644 index 000000000000..a626fc1bbf0d --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/isl9305.txt @@ -0,0 +1,36 @@ +Intersil ISL9305/ISL9305H voltage regulator + +Required properties: + +- compatible: "isl,isl9305" or "isl,isl9305h" +- reg: I2C slave address, usually 0x68. +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name, with valid + values being "dcd1", "dcd2", "ldo1" and "ldo2". The content of each sub-node + is defined by the standard binding for regulators; see regulator.txt. +- VINDCD1-supply: A phandle to a regulator node supplying VINDCD1. + VINDCD2-supply: A phandle to a regulator node supplying VINDCD2. + VINLDO1-supply: A phandle to a regulator node supplying VINLDO1. + VINLDO2-supply: A phandle to a regulator node supplying VINLDO2. + +Optional properties: +- Per-regulator optional properties are defined in regulator.txt + +Example + + pmic: isl9305@68 { + compatible = "isl,isl9305"; + reg = <0x68>; + + VINDCD1-supply = <&system_power>; + VINDCD2-supply = <&system_power>; + VINLDO1-supply = <&system_power>; + VINLDO2-supply = <&system_power>; + + regulators { + dcd1 { + regulator-name = "VDD_DSP"; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/ltc3589.txt b/Documentation/devicetree/bindings/regulator/ltc3589.txt new file mode 100644 index 000000000000..801053036146 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/ltc3589.txt @@ -0,0 +1,99 @@ +Linear Technology LTC3589, LTC3589-1, and LTC3589-2 8-output regulators + +Required properties: +- compatible: "lltc,ltc3589", "lltc,ltc3589-1" or "lltc,ltc3589-2" +- reg: I2C slave address + +Required child node: +- regulators: Contains eight regulator child nodes sw1, sw2, sw3, bb-out, + ldo1, ldo2, ldo3, and ldo4, specifying the initialization data as + documented in Documentation/devicetree/bindings/regulator/regulator.txt. + +Each regulator is defined using the standard binding for regulators. The +nodes for sw1, sw2, sw3, bb-out, ldo1, and ldo2 additionally need to specify +the resistor values of their external feedback voltage dividers: + +Required properties (not on ldo3, ldo4): +- lltc,fb-voltage-divider: An array of two integers containing the resistor + values R1 and R2 of the feedback voltage divider in ohms. + +Regulators sw1, sw2, sw3, and ldo2 can regulate the feedback reference from +0.3625 V to 0.75 V in 12.5 mV steps. The output voltage thus ranges between +0.3625 * (1 + R1/R2) V and 0.75 * (1 + R1/R2) V. Regulators bb-out and ldo1 +have a fixed 0.8 V reference and thus output 0.8 * (1 + R1/R2) V. The ldo3 +regulator is fixed to 1.8 V on LTC3589 and to 2.8 V on LTC3589-1,2. The ldo4 +regulator can output between 1.8 V and 3.3 V on LTC3589 and between 1.2 V +and 3.2 V on LTC3589-1,2 in four steps. The ldo1 standby regulator can not +be disabled and thus should have the regulator-always-on property set. + +Example: + + ltc3589: pmic@34 { + compatible = "lltc,ltc3589-1"; + reg = <0x34>; + + regulators { + sw1_reg: sw1 { + regulator-min-microvolt = <591930>; + regulator-max-microvolt = <1224671>; + lltc,fb-voltage-divider = <100000 158000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <704123>; + regulator-max-microvolt = <1456803>; + lltc,fb-voltage-divider = <180000 191000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3_reg: sw3 { + regulator-min-microvolt = <1341250>; + regulator-max-microvolt = <2775000>; + lltc,fb-voltage-divider = <270000 100000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + bb_out_reg: bb-out { + regulator-min-microvolt = <3387341>; + regulator-max-microvolt = <3387341>; + lltc,fb-voltage-divider = <511000 158000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: ldo1 { + regulator-min-microvolt = <1306329>; + regulator-max-microvolt = <1306329>; + lltc,fb-voltage-divider = <100000 158000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: ldo2 { + regulator-min-microvolt = <704123>; + regulator-max-microvolt = <1456806>; + lltc,fb-voltage-divider = <180000 191000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: ldo3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-boot-on; + }; + + ldo4_reg: ldo4 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3200000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/max1586-regulator.txt b/Documentation/devicetree/bindings/regulator/max1586-regulator.txt new file mode 100644 index 000000000000..c050c1744cb8 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max1586-regulator.txt @@ -0,0 +1,28 @@ +Maxim MAX1586 voltage regulator + +Required properties: +- compatible: must be "maxim,max1586" +- reg: I2C slave address, usually 0x14 +- v3-gain: integer specifying the V3 gain as per datasheet + (1 + R24/R25 + R24/185.5kOhm) +- any required generic properties defined in regulator.txt + +Example: + + i2c_master { + max1586@14 { + compatible = "maxim,max1586"; + reg = <0x14>; + v3-gain = <1000000>; + + regulators { + vcc_core: v3 { + regulator-name = "vcc_core"; + regulator-compatible = "Output_V3"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1705000>; + regulator-always-on; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/max77802.txt b/Documentation/devicetree/bindings/regulator/max77802.txt new file mode 100644 index 000000000000..79e5476444f7 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max77802.txt @@ -0,0 +1,88 @@ +Binding for Maxim MAX77802 regulators + +This is a part of device tree bindings of MAX77802 multi-function device. +More information can be found in bindings/mfd/max77802.txt file. + +The MAX77802 PMIC has 10 high-efficiency Buck and 32 Low-dropout (LDO) +regulators that can be controlled over I2C. + +Following properties should be present in main device node of the MFD chip. + +Optional node: +- regulators : The regulators of max77802 have to be instantiated + under subnode named "regulators" using the following format. + + regulator-name { + standard regulator constraints.... + }; + refer Documentation/devicetree/bindings/regulator/regulator.txt + +The regulator node name should be initialized with a string to get matched +with their hardware counterparts as follow. The valid names are: + + -LDOn : for LDOs, where n can lie in ranges 1-15, 17-21, 23-30 + and 32-35. + example: LDO1, LDO2, LDO35. + -BUCKn : for BUCKs, where n can lie in range 1 to 10. + example: BUCK1, BUCK5, BUCK10. + +The max77802 regulator supports two different operating modes: Normal and Low +Power Mode. Some regulators support the modes to be changed at startup or by +the consumers during normal operation while others only support to change the +mode during system suspend. The standard regulator suspend states binding can +be used to configure the regulator operating mode. + +The regulators that support the standard "regulator-initial-mode" property, +changing their mode during normal operation are: LDOs 1, 3, 20 and 21. + +The possible values for "regulator-initial-mode" and "regulator-mode" are: + 1: Normal regulator voltage output mode. + 3: Low Power which reduces the quiescent current down to only 1uA + +The list of valid modes are defined in the dt-bindings/clock/maxim,max77802.h +header and can be included by device tree source files. + +The standard "regulator-mode" property can only be used for regulators that +support changing their mode to Low Power Mode during suspend. These regulators +are: BUCKs 2-4 and LDOs 1-35. Also, it only takes effect if the regulator has +been enabled for the given suspend state using "regulator-on-in-suspend" and +has not been disabled for that state using "regulator-off-in-suspend". + +Example: + + max77802@09 { + compatible = "maxim,max77802"; + interrupt-parent = <&wakeup_eint>; + interrupts = <26 0>; + reg = <0x09>; + #address-cells = <1>; + #size-cells = <0>; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "vdd_1v0"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-initial-mode = <MAX77802_OPMODE_LP>; + }; + + ldo11_reg: LDO11 { + regulator-name = "vdd_ldo11"; + regulator-min-microvolt = <1900000>; + regulator-max-microvolt = <1900000>; + regulator-always-on; + regulator-state-mem { + regulator-on-in-suspend; + regulator-mode = <MAX77802_OPMODE_LP>; + }; + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/palmas-pmic.txt b/Documentation/devicetree/bindings/regulator/palmas-pmic.txt index 42e6b6bc48ff..725393c8a7f2 100644 --- a/Documentation/devicetree/bindings/regulator/palmas-pmic.txt +++ b/Documentation/devicetree/bindings/regulator/palmas-pmic.txt @@ -7,6 +7,7 @@ Required properties: ti,twl6037-pmic ti,tps65913-pmic ti,tps65914-pmic + ti,tps65917-pmic and also the generic series names ti,palmas-pmic - interrupt-parent : The parent interrupt controller which is palmas. diff --git a/Documentation/devicetree/bindings/regulator/pbias-regulator.txt b/Documentation/devicetree/bindings/regulator/pbias-regulator.txt new file mode 100644 index 000000000000..32aa26f1e434 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/pbias-regulator.txt @@ -0,0 +1,27 @@ +PBIAS internal regulator for SD card dual voltage i/o pads on OMAP SoCs. + +Required properties: +- compatible: + - "ti,pbias-omap" for OMAP2, OMAP3, OMAP4, OMAP5, DRA7. +- reg: pbias register offset from syscon base and size of pbias register. +- syscon : phandle of the system control module +- regulator-name : should be + pbias_mmc_omap2430 for OMAP2430, OMAP3 SoCs + pbias_sim_omap3 for OMAP3 SoCs + pbias_mmc_omap4 for OMAP4 SoCs + pbias_mmc_omap5 for OMAP5 and DRA7 SoC + +Optional properties: +- Any optional property defined in bindings/regulator/regulator.txt + +Example: + + pbias_regulator: pbias_regulator { + compatible = "ti,pbias-omap"; + reg = <0 0x4>; + syscon = <&omap5_padconf_global>; + pbias_mmc_reg: pbias_mmc_omap5 { + regulator-name = "pbias_mmc_omap5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + }; diff --git a/Documentation/devicetree/bindings/regulator/pfuze100.txt b/Documentation/devicetree/bindings/regulator/pfuze100.txt index fc989b2e8057..34ef5d16d0f1 100644 --- a/Documentation/devicetree/bindings/regulator/pfuze100.txt +++ b/Documentation/devicetree/bindings/regulator/pfuze100.txt @@ -1,7 +1,7 @@ PFUZE100 family of regulators Required properties: -- compatible: "fsl,pfuze100" +- compatible: "fsl,pfuze100" or "fsl,pfuze200" - reg: I2C slave address Required child node: @@ -10,11 +10,14 @@ Required child node: Documentation/devicetree/bindings/regulator/regulator.txt. The valid names for regulators are: + --PFUZE100 sw1ab,sw1c,sw2,sw3a,sw3b,sw4,swbst,vsnvs,vrefddr,vgen1~vgen6 + --PFUZE200 + sw1ab,sw2,sw3a,sw3b,swbst,vsnvs,vrefddr,vgen1~vgen6 Each regulator is defined using the standard binding for regulators. -Example: +Example 1: PFUZE100 pmic: pfuze100@08 { compatible = "fsl,pfuze100"; @@ -113,3 +116,92 @@ Example: }; }; }; + + +Example 2: PFUZE200 + + pmic: pfuze200@08 { + compatible = "fsl,pfuze200"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1ab { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3a { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3b_reg: sw3b { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen2_reg: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen3_reg: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + vgen4_reg: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt new file mode 100644 index 000000000000..ce91f61feb12 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt @@ -0,0 +1,27 @@ +pwm regulator bindings + +Required properties: +- compatible: Should be "pwm-regulator" +- pwms: OF device-tree PWM specification (see PWM binding pwm.txt) +- voltage-table: voltage and duty table, include 2 members in each set of + brackets, first one is voltage(unit: uv), the next is duty(unit: percent) + +Any property defined as part of the core regulator binding defined in +regulator.txt can also be used. + +Example: + pwm_regulator { + compatible = "pwm-regulator; + pwms = <&pwm1 0 8448 0>; + + voltage-table = <1114000 0>, + <1095000 10>, + <1076000 20>, + <1056000 30>, + <1036000 40>, + <1016000 50>; + + regulator-min-microvolt = <1016000>; + regulator-max-microvolt = <1114000>; + regulator-name = "vdd_logic"; + }; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index e2c7f1e7251a..abb26b58c83e 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -12,13 +12,31 @@ Optional properties: - regulator-allow-bypass: allow the regulator to go into bypass mode - <name>-supply: phandle to the parent supply/regulator node - regulator-ramp-delay: ramp delay for regulator(in uV/uS) - For hardwares which support disabling ramp rate, it should be explicitly + For hardware which supports disabling ramp rate, it should be explicitly intialised to zero (regulator-ramp-delay = <0>) for disabling ramp delay. - regulator-enable-ramp-delay: The time taken, in microseconds, for the supply rail to reach the target voltage, plus/minus whatever tolerance the board design requires. This property describes the total system ramp time required due to the combination of internal ramping of the regulator itself, and board design issues such as trace capacitance and load on the supply. +- regulator-state-mem sub-root node for Suspend-to-RAM mode + : suspend to memory, the device goes to sleep, but all data stored in memory, + only some external interrupt can wake the device. +- regulator-state-disk sub-root node for Suspend-to-DISK mode + : suspend to disk, this state operates similarly to Suspend-to-RAM, + but includes a final step of writing memory contents to disk. +- regulator-state-[mem/disk] node has following common properties: + - regulator-on-in-suspend: regulator should be on in suspend state. + - regulator-off-in-suspend: regulator should be off in suspend state. + - regulator-suspend-microvolt: regulator should be set to this voltage + in suspend. + - regulator-mode: operating mode in the given suspend state. + The set of possible operating modes depends on the capabilities of + every hardware so the valid modes are documented on each regulator + device tree binding document. +- regulator-initial-mode: initial operating mode. The set of possible operating + modes depends on the capabilities of every hardware so each device binding + documentation explains which values the regulator supports. Deprecated properties: - regulator-compatible: If a regulator chip contains multiple @@ -34,6 +52,10 @@ Example: regulator-max-microvolt = <2500000>; regulator-always-on; vin-supply = <&vin>; + + regulator-state-mem { + regulator-on-in-suspend; + }; }; Regulator Consumers: diff --git a/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt index fc6b38f035bd..20191315e444 100644 --- a/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt @@ -69,13 +69,16 @@ sub-node should be of the format as listed below. }; }; The above regulator entries are defined in regulator bindings documentation -except op_mode description. +except these properties: - op_mode: describes the different operating modes of the LDO's with power mode change in SOC. The different possible values are, 0 - always off mode 1 - on in normal mode 2 - low power mode 3 - suspend mode + - s5m8767,pmic-ext-control-gpios: (optional) GPIO specifier for one + GPIO controlling this regulator (enable/disable); This is + valid only for buck9. The following are the names of the regulators that the s5m8767 pmic block supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number @@ -83,7 +86,7 @@ as per the datasheet of s5m8767. - LDOn - valid values for n are 1 to 28 - - Example: LDO1, LD02, LDO28 + - Example: LDO1, LDO2, LDO28 - BUCKn - valid values for n are 1 to 9. - Example: BUCK1, BUCK2, BUCK9 @@ -148,5 +151,13 @@ Example: regulator-always-on; regulator-boot-on; }; + + vemmc_reg: BUCK9 { + regulator-name = "VMEM_VDD_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + op_mode = <3>; /* Standby Mode */ + s5m8767,pmic-ext-control-gpios = <&gpk0 2 0>; + }; }; }; diff --git a/Documentation/devicetree/bindings/regulator/sky81452-regulator.txt b/Documentation/devicetree/bindings/regulator/sky81452-regulator.txt new file mode 100644 index 000000000000..f9acbc1f3c6b --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/sky81452-regulator.txt @@ -0,0 +1,18 @@ +SKY81452 voltage regulator + +Required properties: +- regulator node named lout. +- any required generic properties defined in regulator.txt + +Optional properties: +- any available generic properties defined in regulator.txt + +Example: + + regulator { + lout { + regulator-name = "sky81452-lout"; + regulator-min-microvolt = <4500000>; + regulator-max-microvolt = <8000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt index 2e57a33e9029..c58db75f959e 100644 --- a/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt @@ -4,10 +4,14 @@ Required Properties: - compatible: Should be one of: - "ti,abb-v1" for older SoCs like OMAP3 - "ti,abb-v2" for newer SoCs like OMAP4, OMAP5 + - "ti,abb-v3" for a generic definition where setup and control registers are + provided (example: DRA7) - reg: Address and length of the register set for the device. It contains the information of registers in the same order as described by reg-names - reg-names: Should contain the reg names - - "base-address" - contains base address of ABB module + - "base-address" - contains base address of ABB module (ti,abb-v1,ti,abb-v2) + - "control-address" - contains control register address of ABB module (ti,abb-v3) + - "setup-address" - contains setup register address of ABB module (ti,abb-v3) - "int-address" - contains address of interrupt register for ABB module (also see Optional properties) - #address-cell: should be 0 diff --git a/Documentation/devicetree/bindings/regulator/tps65090.txt b/Documentation/devicetree/bindings/regulator/tps65090.txt index 313a60ba61d8..ca69f5e3040c 100644 --- a/Documentation/devicetree/bindings/regulator/tps65090.txt +++ b/Documentation/devicetree/bindings/regulator/tps65090.txt @@ -21,6 +21,10 @@ Optional properties: number should be provided. If it is externally controlled and no GPIO entry then driver will just configure this rails as external control and will not provide any enable/disable APIs. +- ti,overcurrent-wait: This is applicable to FET registers, which have a + poorly defined "overcurrent wait" field. If this property is present it + should be between 0 - 3. If this property isn't present we won't touch the + "overcurrent wait" field and we'll leave it to the BIOS/EC to deal with. Each regulator is defined using the standard binding for regulators. @@ -41,8 +45,8 @@ Example: infet5-supply = <&some_reg>; infet6-supply = <&some_reg>; infet7-supply = <&some_reg>; - vsys_l1-supply = <&some_reg>; - vsys_l2-supply = <&some_reg>; + vsys-l1-supply = <&some_reg>; + vsys-l2-supply = <&some_reg>; regulators { dcdc1 { diff --git a/Documentation/devicetree/bindings/regulator/tps65218.txt b/Documentation/devicetree/bindings/regulator/tps65218.txt new file mode 100644 index 000000000000..fccc1d24af58 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/tps65218.txt @@ -0,0 +1,23 @@ +TPS65218 family of regulators + +Required properties: +For tps65218 regulators/LDOs +- compatible: + - "ti,tps65218-dcdc1" for DCDC1 + - "ti,tps65218-dcdc2" for DCDC2 + - "ti,tps65218-dcdc3" for DCDC3 + - "ti,tps65218-dcdc4" for DCDC4 + - "ti,tps65218-dcdc5" for DCDC5 + - "ti,tps65218-dcdc6" for DCDC6 + - "ti,tps65218-ldo1" for LDO1 + +Optional properties: +- Any optional property defined in bindings/regulator/regulator.txt + +Example: + + xyz: regulator@0 { + compatible = "ti,tps65218-dcdc1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + }; diff --git a/Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt b/Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt new file mode 100644 index 000000000000..3da0ebdba8d9 --- /dev/null +++ b/Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt @@ -0,0 +1,133 @@ +*** Reserved memory regions *** + +Reserved memory is specified as a node under the /reserved-memory node. +The operating system shall exclude reserved memory from normal usage +one can create child nodes describing particular reserved (excluded from +normal use) memory regions. Such memory regions are usually designed for +the special usage by various device drivers. + +Parameters for each memory region can be encoded into the device tree +with the following nodes: + +/reserved-memory node +--------------------- +#address-cells, #size-cells (required) - standard definition + - Should use the same values as the root node +ranges (required) - standard definition + - Should be empty + +/reserved-memory/ child nodes +----------------------------- +Each child of the reserved-memory node specifies one or more regions of +reserved memory. Each child node may either use a 'reg' property to +specify a specific range of reserved memory, or a 'size' property with +optional constraints to request a dynamically allocated block of memory. + +Following the generic-names recommended practice, node names should +reflect the purpose of the node (ie. "framebuffer" or "dma-pool"). Unit +address (@<address>) should be appended to the name if the node is a +static allocation. + +Properties: +Requires either a) or b) below. +a) static allocation + reg (required) - standard definition +b) dynamic allocation + size (required) - length based on parent's #size-cells + - Size in bytes of memory to reserve. + alignment (optional) - length based on parent's #size-cells + - Address boundary for alignment of allocation. + alloc-ranges (optional) - prop-encoded-array (address, length pairs). + - Specifies regions of memory that are + acceptable to allocate from. + +If both reg and size are present, then the reg property takes precedence +and size is ignored. + +Additional properties: +compatible (optional) - standard definition + - may contain the following strings: + - shared-dma-pool: This indicates a region of memory meant to be + used as a shared pool of DMA buffers for a set of devices. It can + be used by an operating system to instanciate the necessary pool + management subsystem if necessary. + - vendor specific string in the form <vendor>,[<device>-]<usage> +no-map (optional) - empty property + - Indicates the operating system must not create a virtual mapping + of the region as part of its standard mapping of system memory, + nor permit speculative access to it under any circumstances other + than under the control of the device driver using the region. +reusable (optional) - empty property + - The operating system can use the memory in this region with the + limitation that the device driver(s) owning the region need to be + able to reclaim it back. Typically that means that the operating + system can use that region to store volatile or cached data that + can be otherwise regenerated or migrated elsewhere. + +Linux implementation note: +- If a "linux,cma-default" property is present, then Linux will use the + region for the default pool of the contiguous memory allocator. + +Device node references to reserved memory +----------------------------------------- +Regions in the /reserved-memory node may be referenced by other device +nodes by adding a memory-region property to the device node. + +memory-region (optional) - phandle, specifier pairs to children of /reserved-memory + +Example +------- +This example defines 3 contiguous regions are defined for Linux kernel: +one default of all device drivers (named linux,cma@72000000 and 64MiB in size), +one dedicated to the framebuffer device (named framebuffer@78000000, 8MiB), and +one for multimedia processing (named multimedia-memory@77000000, 64MiB). + +/ { + #address-cells = <1>; + #size-cells = <1>; + + memory { + reg = <0x40000000 0x40000000>; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + /* global autoconfigured region for contiguous allocations */ + linux,cma { + compatible = "shared-dma-pool"; + reusable; + size = <0x4000000>; + alignment = <0x2000>; + linux,cma-default; + }; + + display_reserved: framebuffer@78000000 { + reg = <0x78000000 0x800000>; + }; + + multimedia_reserved: multimedia@77000000 { + compatible = "acme,multimedia-memory"; + reg = <0x77000000 0x4000000>; + }; + }; + + /* ... */ + + fb0: video@12300000 { + memory-region = <&display_reserved>; + /* ... */ + }; + + scaler: scaler@12500000 { + memory-region = <&multimedia_reserved>; + /* ... */ + }; + + codec: codec@12600000 { + memory-region = <&multimedia_reserved>; + /* ... */ + }; +}; diff --git a/Documentation/devicetree/bindings/reset/allwinner,sunxi-clock-reset.txt b/Documentation/devicetree/bindings/reset/allwinner,sunxi-clock-reset.txt new file mode 100644 index 000000000000..c8f775714887 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/allwinner,sunxi-clock-reset.txt @@ -0,0 +1,21 @@ +Allwinner sunxi Peripheral Reset Controller +=========================================== + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: +- compatible: Should be one of the following: + "allwinner,sun6i-a31-ahb1-reset" + "allwinner,sun6i-a31-clock-reset" +- reg: should be register base and length as documented in the + datasheet +- #reset-cells: 1, see below + +example: + +ahb1_rst: reset@01c202c0 { + #reset-cells = <1>; + compatible = "allwinner,sun6i-a31-ahb1-reset"; + reg = <0x01c202c0 0xc>; +}; diff --git a/Documentation/devicetree/bindings/reset/sirf,rstc.txt b/Documentation/devicetree/bindings/reset/sirf,rstc.txt new file mode 100644 index 000000000000..0505de742d30 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/sirf,rstc.txt @@ -0,0 +1,42 @@ +CSR SiRFSoC Reset Controller +====================================== + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: +- compatible: Should be "sirf,prima2-rstc" or "sirf,marco-rstc" +- reg: should be register base and length as documented in the + datasheet +- #reset-cells: 1, see below + +example: + +rstc: reset-controller@88010000 { + compatible = "sirf,prima2-rstc"; + reg = <0x88010000 0x1000>; + #reset-cells = <1>; +}; + +Specifying reset lines connected to IP modules +============================================== + +The reset controller(rstc) manages various reset sources. This module provides +reset signals for most blocks in system. Those device nodes should specify the +reset line on the rstc in their resets property, containing a phandle to the +rstc device node and a RESET_INDEX specifying which module to reset, as described +in reset.txt. + +For SiRFSoC, RESET_INDEX is just reset_bit defined in SW_RST0 and SW_RST1 registers. +For modules whose rest_bit is in SW_RST0, its RESET_INDEX is 0~31. For modules whose +rest_bit is in SW_RST1, its RESET_INDEX is 32~63. + +example: + +vpp@90020000 { + compatible = "sirf,prima2-vpp"; + reg = <0x90020000 0x10000>; + interrupts = <31>; + clocks = <&clks 35>; + resets = <&rstc 6>; +}; diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-reset.txt b/Documentation/devicetree/bindings/reset/socfpga-reset.txt index ecdb57d69dbf..32c1c8bfd5dc 100644 --- a/Documentation/devicetree/bindings/arm/altera/socfpga-reset.txt +++ b/Documentation/devicetree/bindings/reset/socfpga-reset.txt @@ -3,9 +3,11 @@ Altera SOCFPGA Reset Manager Required properties: - compatible : "altr,rst-mgr" - reg : Should contain 1 register ranges(address and length) +- #reset-cells: 1 Example: rstmgr@ffd05000 { + #reset-cells = <1>; compatible = "altr,rst-mgr"; reg = <0xffd05000 0x1000>; }; diff --git a/Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt b/Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt new file mode 100644 index 000000000000..54ae9f747e45 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt @@ -0,0 +1,42 @@ +STMicroelectronics STi family Sysconfig Picophy SoftReset Controller +============================================================================= + +This binding describes a reset controller device that is used to enable and +disable on-chip PicoPHY USB2 phy(s) using "softreset" control bits found in +the STi family SoC system configuration registers. + +The actual action taken when softreset is asserted is hardware dependent. +However, when asserted it may not be possible to access the hardware's +registers and after an assert/deassert sequence the hardware's previous state +may no longer be valid. + +Please refer to Documentation/devicetree/bindings/reset/reset.txt +for common reset controller binding usage. + +Required properties: +- compatible: Should be "st,stih407-picophyreset" +- #reset-cells: 1, see below + +Example: + + picophyreset: picophyreset-controller { + compatible = "st,stih407-picophyreset"; + #reset-cells = <1>; + }; + +Specifying picophyreset control of devices +======================================= + +Device nodes should specify the reset channel required in their "resets" +property, containing a phandle to the picophyreset device node and an +index specifying which channel to use, as described in +Documentation/devicetree/bindings/reset/reset.txt. + +Example: + + usb2_picophy0: usbpicophy@0 { + resets = <&picophyreset STIH407_PICOPHY0_RESET>; + }; + +Macro definitions for the supported reset channels can be found in: +include/dt-bindings/reset-controller/stih407-resets.h diff --git a/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt b/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt new file mode 100644 index 000000000000..5ab26b7e9d35 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt @@ -0,0 +1,47 @@ +STMicroelectronics STi family Sysconfig Peripheral Powerdown Reset Controller +============================================================================= + +This binding describes a reset controller device that is used to enable and +disable on-chip peripheral controllers such as USB and SATA, using +"powerdown" control bits found in the STi family SoC system configuration +registers. These have been grouped together into a single reset controller +device for convenience. + +The actual action taken when powerdown is asserted is hardware dependent. +However, when asserted it may not be possible to access the hardware's +registers and after an assert/deassert sequence the hardware's previous state +may no longer be valid. + +Please refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: +- compatible: Should be "st,<chip>-powerdown" + ex: "st,stih415-powerdown", "st,stih416-powerdown" +- #reset-cells: 1, see below + +example: + + powerdown: powerdown-controller { + #reset-cells = <1>; + compatible = "st,stih415-powerdown"; + }; + + +Specifying powerdown control of devices +======================================= + +Device nodes should specify the reset channel required in their "resets" +property, containing a phandle to the powerdown device node and an +index specifying which channel to use, as described in reset.txt + +example: + + usb1: usb@fe200000 { + resets = <&powerdown STIH41X_USB1_POWERDOWN>; + }; + +Macro definitions for the supported reset channels can be found in: + +include/dt-bindings/reset-controller/stih415-resets.h +include/dt-bindings/reset-controller/stih416-resets.h diff --git a/Documentation/devicetree/bindings/reset/st,sti-softreset.txt b/Documentation/devicetree/bindings/reset/st,sti-softreset.txt new file mode 100644 index 000000000000..a8d3d3c25ca2 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/st,sti-softreset.txt @@ -0,0 +1,46 @@ +STMicroelectronics STi family Sysconfig Peripheral SoftReset Controller +============================================================================= + +This binding describes a reset controller device that is used to enable and +disable on-chip peripheral controllers such as USB and SATA, using +"softreset" control bits found in the STi family SoC system configuration +registers. + +The actual action taken when softreset is asserted is hardware dependent. +However, when asserted it may not be possible to access the hardware's +registers and after an assert/deassert sequence the hardware's previous state +may no longer be valid. + +Please refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: +- compatible: Should be "st,<chip>-softreset" example: + "st,stih415-softreset" or "st,stih416-softreset"; +- #reset-cells: 1, see below + +example: + + softreset: softreset-controller { + #reset-cells = <1>; + compatible = "st,stih415-softreset"; + }; + + +Specifying softreset control of devices +======================================= + +Device nodes should specify the reset channel required in their "resets" +property, containing a phandle to the softreset device node and an +index specifying which channel to use, as described in reset.txt + +example: + + ethernet0{ + resets = <&softreset STIH415_ETH0_SOFTRESET>; + }; + +Macro definitions for the supported reset channels can be found in: + +include/dt-bindings/reset-controller/stih415-resets.h +include/dt-bindings/reset-controller/stih416-resets.h diff --git a/Documentation/devicetree/bindings/rng/apm,rng.txt b/Documentation/devicetree/bindings/rng/apm,rng.txt new file mode 100644 index 000000000000..4dde4b06cdd9 --- /dev/null +++ b/Documentation/devicetree/bindings/rng/apm,rng.txt @@ -0,0 +1,17 @@ +APM X-Gene SoC random number generator. + +Required properties: + +- compatible : should be "apm,xgene-rng" +- reg : specifies base physical address and size of the registers map +- clocks : phandle to clock-controller plus clock-specifier pair +- interrupts : specify the fault interrupt for the RNG device + +Example: + + rng: rng@10520000 { + compatible = "apm,xgene-rng"; + reg = <0x0 0x10520000 0x0 0x100>; + interrupts = <0x0 0x41 0x4>; + clocks = <&rngpkaclk 0>; + }; diff --git a/Documentation/devicetree/bindings/rtc/atmel,at91sam9-rtc.txt b/Documentation/devicetree/bindings/rtc/atmel,at91sam9-rtc.txt new file mode 100644 index 000000000000..6ae79d1843f3 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/atmel,at91sam9-rtc.txt @@ -0,0 +1,23 @@ +Atmel AT91SAM9260 Real Time Timer + +Required properties: +- compatible: should be: "atmel,at91sam9260-rtt" +- reg: should encode the memory region of the RTT controller +- interrupts: rtt alarm/event interrupt +- clocks: should contain the 32 KHz slow clk that will drive the RTT block. +- atmel,rtt-rtc-time-reg: should encode the GPBR register used to store + the time base when the RTT is used as an RTC. + The first cell should point to the GPBR node and the second one + encode the offset within the GPBR block (or in other words, the + GPBR register used to store the time base). + + +Example: + +rtt@fffffd20 { + compatible = "atmel,at91sam9260-rtt"; + reg = <0xfffffd20 0x10>; + interrupts = <1 4 7>; + clocks = <&clk32k>; + atmel,rtt-rtc-time-reg = <&gpbr 0x0>; +}; diff --git a/Documentation/devicetree/bindings/rtc/dallas,ds1339.txt b/Documentation/devicetree/bindings/rtc/dallas,ds1339.txt new file mode 100644 index 000000000000..916f57601a8f --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/dallas,ds1339.txt @@ -0,0 +1,18 @@ +* Dallas DS1339 I2C Serial Real-Time Clock + +Required properties: +- compatible: Should contain "dallas,ds1339". +- reg: I2C address for chip + +Optional properties: +- trickle-resistor-ohms : Selected resistor for trickle charger + Values usable for ds1339 are 250, 2000, 4000 + Should be given if trickle charger should be enabled +- trickle-diode-disable : Do not use internal trickle charger diode + Should be given if internal trickle charger diode should be disabled +Example: + ds1339: rtc@68 { + compatible = "dallas,ds1339"; + trickle-resistor-ohms = <250>; + reg = <0x68>; + }; diff --git a/Documentation/devicetree/bindings/rtc/haoyu,hym8563.txt b/Documentation/devicetree/bindings/rtc/haoyu,hym8563.txt index 31406fd4a43e..5c199ee044cb 100644 --- a/Documentation/devicetree/bindings/rtc/haoyu,hym8563.txt +++ b/Documentation/devicetree/bindings/rtc/haoyu,hym8563.txt @@ -9,6 +9,9 @@ Required properties: - interrupts: rtc alarm/event interrupt - #clock-cells: the value should be 0 +Optional properties: +- clock-output-names: From common clock binding + Example: hym8563: hym8563@51 { diff --git a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt index 7ac7259fe9ea..ab757b84daa7 100644 --- a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt @@ -3,7 +3,10 @@ Required properties: - compatible: should be one of the following. * "samsung,s3c2410-rtc" - for controllers compatible with s3c2410 rtc. + * "samsung,s3c2416-rtc" - for controllers compatible with s3c2416 rtc. + * "samsung,s3c2443-rtc" - for controllers compatible with s3c2443 rtc. * "samsung,s3c6410-rtc" - for controllers compatible with s3c6410 rtc. + * "samsung,exynos3250-rtc" - for controllers compatible with exynos3250 rtc. - reg: physical base address of the controller and length of memory mapped region. - interrupts: Two interrupt numbers to the cpu should be specified. First diff --git a/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt b/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt new file mode 100644 index 000000000000..f007e428a1ab --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt @@ -0,0 +1,17 @@ +* sun6i Real Time Clock + +RTC controller for the Allwinner A31 + +Required properties: +- compatible : Should be "allwinner,sun6i-a31-rtc" +- reg : physical base address of the controller and length of + memory mapped region. +- interrupts : IRQ lines for the RTC alarm 0 and alarm 1, in that order. + +Example: + +rtc: rtc@01f00000 { + compatible = "allwinner,sun6i-a31-rtc"; + reg = <0x01f00000 0x54>; + interrupts = <0 40 4>, <0 41 4>; +}; diff --git a/Documentation/devicetree/bindings/rtc/sunxi-rtc.txt b/Documentation/devicetree/bindings/rtc/sunxi-rtc.txt index 7cb9dbf34878..6983aad376c3 100644 --- a/Documentation/devicetree/bindings/rtc/sunxi-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/sunxi-rtc.txt @@ -3,7 +3,7 @@ RTC controller for the Allwinner A10/A20 Required properties: -- compatible : Should be "allwinner,sun4i-rtc" or "allwinner,sun7i-a20-rtc" +- compatible : Should be "allwinner,sun4i-a10-rtc" or "allwinner,sun7i-a20-rtc" - reg: physical base address of the controller and length of memory mapped region. - interrupts: IRQ line for the RTC. @@ -11,7 +11,7 @@ Required properties: Example: rtc: rtc@01c20d00 { - compatible = "allwinner,sun4i-rtc"; + compatible = "allwinner,sun4i-a10-rtc"; reg = <0x01c20d00 0x20>; interrupts = <24>; }; diff --git a/Documentation/devicetree/bindings/rtc/xgene-rtc.txt b/Documentation/devicetree/bindings/rtc/xgene-rtc.txt new file mode 100644 index 000000000000..fd195c358446 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/xgene-rtc.txt @@ -0,0 +1,28 @@ +* APM X-Gene Real Time Clock + +RTC controller for the APM X-Gene Real Time Clock + +Required properties: +- compatible : Should be "apm,xgene-rtc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: IRQ line for the RTC. +- #clock-cells: Should be 1. +- clocks: Reference to the clock entry. + +Example: + +rtcclk: rtcclk { + compatible = "fixed-clock"; + #clock-cells = <1>; + clock-frequency = <100000000>; + clock-output-names = "rtcclk"; +}; + +rtc: rtc@10510000 { + compatible = "apm,xgene-rtc"; + reg = <0x0 0x10510000 0x0 0x400>; + interrupts = <0x0 0x46 0x4>; + #clock-cells = <1>; + clocks = <&rtcclk 0>; +}; diff --git a/Documentation/devicetree/bindings/serial/atmel-usart.txt b/Documentation/devicetree/bindings/serial/atmel-usart.txt index 9c5d19ac935c..a6391e70a8fd 100644 --- a/Documentation/devicetree/bindings/serial/atmel-usart.txt +++ b/Documentation/devicetree/bindings/serial/atmel-usart.txt @@ -13,6 +13,9 @@ Required properties: Optional properties: - atmel,use-dma-rx: use of PDC or DMA for receiving data - atmel,use-dma-tx: use of PDC or DMA for transmitting data +- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD line respectively. + It will use specified PIO instead of the peripheral function pin for the USART feature. + If unsure, don't specify this property. - add dma bindings for dma transfer: - dmas: DMA specifier, consisting of a phandle to DMA controller node, memory peripheral interface and USART DMA channel ID, FIFO configuration. @@ -33,6 +36,12 @@ Example: clock-names = "usart"; atmel,use-dma-rx; atmel,use-dma-tx; + rts-gpios = <&pioD 15 GPIO_ACTIVE_LOW>; + cts-gpios = <&pioD 16 GPIO_ACTIVE_LOW>; + dtr-gpios = <&pioD 17 GPIO_ACTIVE_LOW>; + dsr-gpios = <&pioD 18 GPIO_ACTIVE_LOW>; + dcd-gpios = <&pioD 20 GPIO_ACTIVE_LOW>; + rng-gpios = <&pioD 19 GPIO_ACTIVE_LOW>; }; - use DMA: diff --git a/Documentation/devicetree/bindings/serial/cdns,uart.txt b/Documentation/devicetree/bindings/serial/cdns,uart.txt new file mode 100644 index 000000000000..a3eb154c32ca --- /dev/null +++ b/Documentation/devicetree/bindings/serial/cdns,uart.txt @@ -0,0 +1,20 @@ +Binding for Cadence UART Controller + +Required properties: +- compatible : should be "cdns,uart-r1p8", or "xlnx,xuartps" +- reg: Should contain UART controller registers location and length. +- interrupts: Should contain UART controller interrupts. +- clocks: Must contain phandles to the UART clocks + See ../clocks/clock-bindings.txt for details. +- clock-names: Tuple to identify input clocks, must contain "uart_clk" and "pclk" + See ../clocks/clock-bindings.txt for details. + + +Example: + uart@e0000000 { + compatible = "cdns,uart-r1p8"; + clocks = <&clkc 23>, <&clkc 40>; + clock-names = "uart_clk", "pclk"; + reg = <0xE0000000 0x1000>; + interrupts = <0 27 4>; + }; diff --git a/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt b/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt index 12f3cf834deb..caaeb2583579 100644 --- a/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt +++ b/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt @@ -8,7 +8,8 @@ Required properties: - syscon: Phandle to SYSCON node, which contain UART control bits. Optional properties: -- uart-use-ms: Indicate the UART has modem signal (DCD, DSR, CTS). +- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD + line respectively. Note: Each UART port should have an alias correctly numbered in "aliases" node. @@ -24,5 +25,7 @@ Example: interrupts = <12 13>; clocks = <&clks 11>; syscon = <&syscon1>; - uart-use-ms; + cts-gpios = <&sysgpio 0 GPIO_ACTIVE_LOW>; + dsr-gpios = <&sysgpio 1 GPIO_ACTIVE_LOW>; + dcd-gpios = <&sysgpio 2 GPIO_ACTIVE_LOW>; }; diff --git a/Documentation/devicetree/bindings/serial/efm32-uart.txt b/Documentation/devicetree/bindings/serial/efm32-uart.txt index 8e080b893b49..8adbab268ca3 100644 --- a/Documentation/devicetree/bindings/serial/efm32-uart.txt +++ b/Documentation/devicetree/bindings/serial/efm32-uart.txt @@ -1,20 +1,20 @@ * Energymicro efm32 UART Required properties: -- compatible : Should be "efm32,uart" +- compatible : Should be "energymicro,efm32-uart" - reg : Address and length of the register set - interrupts : Should contain uart interrupt Optional properties: -- location : Decides the location of the USART I/O pins. +- energymicro,location : Decides the location of the USART I/O pins. Allowed range : [0 .. 5] Default: 0 Example: uart@0x4000c400 { - compatible = "efm32,uart"; + compatible = "energymicro,efm32-uart"; reg = <0x4000c400 0x400>; interrupts = <15>; - location = <0>; + energymicro,location = <0>; }; diff --git a/Documentation/devicetree/bindings/serial/fsl-lpuart.txt b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt index 6fd1dd1638dd..c95005efbcb8 100644 --- a/Documentation/devicetree/bindings/serial/fsl-lpuart.txt +++ b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt @@ -1,14 +1,31 @@ * Freescale low power universal asynchronous receiver/transmitter (lpuart) Required properties: -- compatible : Should be "fsl,<soc>-lpuart" +- compatible : + - "fsl,vf610-lpuart" for lpuart compatible with the one integrated + on Vybrid vf610 SoC with 8-bit register organization + - "fsl,ls1021a-lpuart" for lpuart compatible with the one integrated + on LS1021A SoC with 32-bit big-endian register organization - reg : Address and length of the register set for the device - interrupts : Should contain uart interrupt +- clocks : phandle + clock specifier pairs, one for each entry in clock-names +- clock-names : should contain: "ipg" - the uart clock + +Optional properties: +- dmas: A list of two dma specifiers, one for each entry in dma-names. +- dma-names: should contain "tx" and "rx". + +Note: Optional properties for DMA support. Write them both or both not. Example: uart0: serial@40027000 { - compatible = "fsl,vf610-lpuart"; - reg = <0x40027000 0x1000>; - interrupts = <0 61 0x00>; - }; + compatible = "fsl,vf610-lpuart"; + reg = <0x40027000 0x1000>; + interrupts = <0 61 0x00>; + clocks = <&clks VF610_CLK_UART0>; + clock-names = "ipg"; + dmas = <&edma0 0 2>, + <&edma0 0 3>; + dma-names = "rx","tx"; + }; diff --git a/Documentation/devicetree/bindings/serial/maxim,max310x.txt b/Documentation/devicetree/bindings/serial/maxim,max310x.txt new file mode 100644 index 000000000000..83a919c241b0 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/maxim,max310x.txt @@ -0,0 +1,36 @@ +* Maxim MAX310X advanced Universal Asynchronous Receiver-Transmitter (UART) + +Required properties: +- compatible: Should be one of the following: + - "maxim,max3107" for Maxim MAX3107, + - "maxim,max3108" for Maxim MAX3108, + - "maxim,max3109" for Maxim MAX3109, + - "maxim,max14830" for Maxim MAX14830. +- reg: SPI chip select number. +- interrupt-parent: The phandle for the interrupt controller that + services interrupts for this IC. +- interrupts: Specifies the interrupt source of the parent interrupt + controller. The format of the interrupt specifier depends on the + parent interrupt controller. +- clocks: phandle to the IC source clock. +- clock-names: Should be "xtal" if clock is an external crystal or + "osc" if an external clock source is used. + +Optional properties: +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Should be two. The first cell is the GPIO number and + the second cell is used to specify the GPIO polarity: + 0 = active high, + 1 = active low. + +Example: + max14830: max14830@0 { + compatible = "maxim,max14830"; + reg = <0>; + clocks = <&clk20m>; + clock-names = "osc"; + interrupt-parent = <&gpio3>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt new file mode 100644 index 000000000000..48358a33ea7d --- /dev/null +++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt @@ -0,0 +1,22 @@ +* Mediatek Universal Asynchronous Receiver/Transmitter (UART) + +Required properties: +- compatible should contain: + * "mediatek,mt6589-uart" for MT6589 compatible UARTS + * "mediatek,mt6582-uart" for MT6582 compatible UARTS + * "mediatek,mt6577-uart" for all compatible UARTS (MT6589, MT6582, MT6577) + +- reg: The base address of the UART register bank. + +- interrupts: A single interrupt specifier. + +- clocks: Clock driving the hardware. + +Example: + + uart0: serial@11006000 { + compatible = "mediatek,mt6589-uart", "mediatek,mt6577-uart"; + reg = <0x11006000 0x400>; + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>; + clocks = <&uart_clk>; + }; diff --git a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt new file mode 100644 index 000000000000..246c795668dc --- /dev/null +++ b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt @@ -0,0 +1,33 @@ +* NXP SC16IS7xx advanced Universal Asynchronous Receiver-Transmitter (UART) + +Required properties: +- compatible: Should be one of the following: + - "nxp,sc16is740" for NXP SC16IS740, + - "nxp,sc16is741" for NXP SC16IS741, + - "nxp,sc16is750" for NXP SC16IS750, + - "nxp,sc16is752" for NXP SC16IS752, + - "nxp,sc16is760" for NXP SC16IS760, + - "nxp,sc16is762" for NXP SC16IS762. +- reg: I2C address of the SC16IS7xx device. +- interrupt-parent: The phandle for the interrupt controller that + services interrupts for this IC. +- interrupts: Should contain the UART interrupt +- clocks: Reference to the IC source clock. + +Optional properties: +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Should be two. The first cell is the GPIO number and + the second cell is used to specify the GPIO polarity: + 0 = active high, + 1 = active low. + +Example: + sc16is750: sc16is750@51 { + compatible = "nxp,sc16is750"; + reg = <0x51>; + clocks = <&clk20m>; + interrupt-parent = <&gpio3>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/serial/of-serial.txt b/Documentation/devicetree/bindings/serial/of-serial.txt index 1928a3e83cd0..8c4fd0332028 100644 --- a/Documentation/devicetree/bindings/serial/of-serial.txt +++ b/Documentation/devicetree/bindings/serial/of-serial.txt @@ -14,6 +14,7 @@ Required properties: - "altr,16550-FIFO32" - "altr,16550-FIFO64" - "altr,16550-FIFO128" + - "fsl,16550-FIFO64" - "serial" if the port type is unknown. - reg : offset and length of the register set for the device. - interrupts : should contain uart interrupt. diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index f372cf29068d..b3556609a06f 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -4,6 +4,14 @@ Required properties: - compatible: Must contain one of the following: + - "renesas,scifa-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFA compatible UART. + - "renesas,scifb-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFB compatible UART. + - "renesas,scifa-r8a73a4" for R8A73A4 (R-Mobile APE6) SCIFA compatible UART. + - "renesas,scifb-r8a73a4" for R8A73A4 (R-Mobile APE6) SCIFB compatible UART. + - "renesas,scifa-r8a7740" for R8A7740 (R-Mobile A1) SCIFA compatible UART. + - "renesas,scifb-r8a7740" for R8A7740 (R-Mobile A1) SCIFB compatible UART. + - "renesas,scif-r8a7778" for R8A7778 (R-Car M1) SCIF compatible UART. + - "renesas,scif-r8a7779" for R8A7779 (R-Car H1) SCIF compatible UART. - "renesas,scif-r8a7790" for R8A7790 (R-Car H2) SCIF compatible UART. - "renesas,scifa-r8a7790" for R8A7790 (R-Car H2) SCIFA compatible UART. - "renesas,scifb-r8a7790" for R8A7790 (R-Car H2) SCIFB compatible UART. @@ -37,7 +45,7 @@ Example: }; scifa0: serial@e6c40000 { - compatible = "renesas,scifa-r8a7790", "renesas,scifa-generic"; + compatible = "renesas,scifa-r8a7790", "renesas,scifa"; reg = <0 0xe6c40000 0 64>; interrupt-parent = <&gic>; interrupts = <0 144 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/serial/samsung_uart.txt b/Documentation/devicetree/bindings/serial/samsung_uart.txt index 2c8a17cf5cb5..e85f37ec33f0 100644 --- a/Documentation/devicetree/bindings/serial/samsung_uart.txt +++ b/Documentation/devicetree/bindings/serial/samsung_uart.txt @@ -1,14 +1,58 @@ * Samsung's UART Controller -The Samsung's UART controller is used for interfacing SoC with serial communicaion -devices. +The Samsung's UART controller is used for interfacing SoC with serial +communicaion devices. Required properties: -- compatible: should be - - "samsung,exynos4210-uart", for UART's compatible with Exynos4210 uart ports. +- compatible: should be one of following: + - "samsung,exynos4210-uart" - Exynos4210 SoC, + - "samsung,s3c2410-uart" - compatible with ports present on S3C2410 SoC, + - "samsung,s3c2412-uart" - compatible with ports present on S3C2412 SoC, + - "samsung,s3c2440-uart" - compatible with ports present on S3C2440 SoC, + - "samsung,s3c6400-uart" - compatible with ports present on S3C6400 SoC, + - "samsung,s5pv210-uart" - compatible with ports present on S5PV210 SoC. - reg: base physical address of the controller and length of memory mapped region. -- interrupts: interrupt number to the cpu. The interrupt specifier format depends - on the interrupt controller parent. +- interrupts: a single interrupt signal to SoC interrupt controller, + according to interrupt bindings documentation [1]. + +- clock-names: input names of clocks used by the controller: + - "uart" - controller bus clock, + - "clk_uart_baudN" - Nth baud base clock input (N = 0, 1, ...), + according to SoC User's Manual (only N = 0 is allowedfor SoCs without + internal baud clock mux). +- clocks: phandles and specifiers for all clocks specified in "clock-names" + property, in the same order, according to clock bindings documentation [2]. + +[1] Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +[2] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Optional properties: +- samsung,uart-fifosize: The fifo size supported by the UART channel + +Note: Each Samsung UART should have an alias correctly numbered in the +"aliases" node, according to serialN format, where N is the port number +(non-negative decimal integer) as specified by User's Manual of respective +SoC. + +Example: + aliases { + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + }; + +Example: + uart1: serial@7f005400 { + compatible = "samsung,s3c6400-uart"; + reg = <0x7f005400 0x100>; + interrupt-parent = <&vic1>; + interrupts = <6>; + clock-names = "uart", "clk_uart_baud2", + "clk_uart_baud3"; + clocks = <&clocks PCLK_UART1>, <&clocks PCLK_UART1>, + <&clocks SCLK_UART>; + samsung,uart-fifosize = <16>; + }; diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt index f13f1c5be91c..7f76214f728a 100644 --- a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt +++ b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt @@ -4,9 +4,18 @@ Required properties: - compatible : "snps,dw-apb-uart" - reg : offset and length of the register set for the device. - interrupts : should contain uart interrupt. + +Clock handling: +The clock rate of the input clock needs to be supplied by one of - clock-frequency : the input clock frequency for the UART. +- clocks : phandle to the input clock + +The supplying peripheral clock can also be handled, needing a second property +- clock-names: tuple listing input clock names. + Required elements: "baudclk", "apb_pclk" Optional properties: +- resets : phandle to the parent reset controller. - reg-shift : quantity to shift the register offsets by. If this property is not present then the register offsets are not shifted. - reg-io-width : the size (in bytes) of the IO accesses that should be @@ -23,3 +32,26 @@ Example: reg-shift = <2>; reg-io-width = <4>; }; + +Example with one clock: + + uart@80230000 { + compatible = "snps,dw-apb-uart"; + reg = <0x80230000 0x100>; + clocks = <&baudclk>; + interrupts = <10>; + reg-shift = <2>; + reg-io-width = <4>; + }; + +Example with two clocks: + + uart@80230000 { + compatible = "snps,dw-apb-uart"; + reg = <0x80230000 0x100>; + clocks = <&baudclk>, <&apb_pclk>; + clock-names = "baudclk", "apb_pclk"; + interrupts = <10>; + reg-shift = <2>; + reg-io-width = <4>; + }; diff --git a/Documentation/devicetree/bindings/serial/via,vt8500-uart.txt b/Documentation/devicetree/bindings/serial/via,vt8500-uart.txt deleted file mode 100644 index 5feef1ef167d..000000000000 --- a/Documentation/devicetree/bindings/serial/via,vt8500-uart.txt +++ /dev/null @@ -1,17 +0,0 @@ -VIA/Wondermedia VT8500 UART Controller ------------------------------------------------------ - -Required properties: -- compatible : "via,vt8500-uart" -- reg : Should contain 1 register ranges(address and length) -- interrupts : UART interrupt -- clocks : phandle to the uart source clock (usually a 24Mhz fixed clock) - -Example: - - uart@d8210000 { - compatible = "via,vt8500-uart"; - reg = <0xd8210000 0x1040>; - interrupts = <47>; - clocks = <&ref24>; - }; diff --git a/Documentation/devicetree/bindings/serial/vt8500-uart.txt b/Documentation/devicetree/bindings/serial/vt8500-uart.txt index 795c393d09c4..2b64e6107fb3 100644 --- a/Documentation/devicetree/bindings/serial/vt8500-uart.txt +++ b/Documentation/devicetree/bindings/serial/vt8500-uart.txt @@ -1,7 +1,8 @@ * VIA VT8500 and WonderMedia WM8xxx UART Controller Required properties: -- compatible: should be "via,vt8500-uart" +- compatible: should be "via,vt8500-uart" (for VIA/WonderMedia chips up to and + including WM8850/WM8950), or "wm,wm8880-uart" (for WM8880 and later) - reg: base physical address of the controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt new file mode 100644 index 000000000000..4ce24d425bf1 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt @@ -0,0 +1,78 @@ +QCOM GSBI (General Serial Bus Interface) Driver + +The GSBI controller is modeled as a node with zero or more child nodes, each +representing a serial sub-node device that is mux'd as part of the GSBI +configuration settings. The mode setting will govern the input/output mode of +the 4 GSBI IOs. + +Required properties: +- compatible: must contain "qcom,gsbi-v1.0.0" for APQ8064/IPQ8064 +- reg: Address range for GSBI registers +- clocks: required clock +- clock-names: must contain "iface" entry +- qcom,mode : indicates MUX value for configuration of the serial interface. + Please reference dt-bindings/soc/qcom,gsbi.h for valid mux values. + +Optional properties: +- qcom,crci : indicates CRCI MUX value for QUP CRCI ports. Please reference + dt-bindings/soc/qcom,gsbi.h for valid CRCI mux values. + +Required properties if child node exists: +- #address-cells: Must be 1 +- #size-cells: Must be 1 +- ranges: Must be present + +Properties for children: + +A GSBI controller node can contain 0 or more child nodes representing serial +devices. These serial devices can be a QCOM UART, I2C controller, spi +controller, or some combination of aforementioned devices. + +See the following for child node definitions: +Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt +Documentation/devicetree/bindings/spi/qcom,spi-qup.txt +Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt + +Example for APQ8064: + +#include <dt-bindings/soc/qcom,gsbi.h> + + gsbi4@16300000 { + compatible = "qcom,gsbi-v1.0.0"; + reg = <0x16300000 0x100>; + clocks = <&gcc GSBI4_H_CLK>; + clock-names = "iface"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + qcom,mode = <GSBI_PROT_I2C_UART>; + qcom,crci = <GSBI_CRCI_QUP>; + + /* child nodes go under here */ + + i2c_qup4: i2c@16380000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x16380000 0x1000>; + interrupts = <0 153 0>; + + clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>; + clock-names = "core", "iface"; + + clock-frequency = <200000>; + + #address-cells = <1>; + #size-cells = <0>; + + }; + + uart4: serial@16340000 { + compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; + reg = <0x16340000 0x1000>, + <0x16300000 0x1000>; + interrupts = <0 152 0x0>; + clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>; + clock-names = "core", "iface"; + status = "ok"; + }; + }; + diff --git a/Documentation/devicetree/bindings/soc/ti/keystone-navigator-dma.txt b/Documentation/devicetree/bindings/soc/ti/keystone-navigator-dma.txt new file mode 100644 index 000000000000..337c4ea5c57b --- /dev/null +++ b/Documentation/devicetree/bindings/soc/ti/keystone-navigator-dma.txt @@ -0,0 +1,111 @@ +Keystone Navigator DMA Controller + +This document explains the device tree bindings for the packet dma +on keystone devices. The Keystone Navigator DMA driver sets up the dma +channels and flows for the QMSS(Queue Manager SubSystem) who triggers +the actual data movements across clients using destination queues. Every +client modules like NETCP(Network Coprocessor), SRIO(Serial Rapid IO), +CRYPTO Engines etc has its own instance of dma hardware. QMSS has also +an internal packet DMA module which is used as an infrastructure DMA +with zero copy. + +Navigator DMA cloud layout: + ------------------ + | Navigator DMAs | + ------------------ + | + |-> DMA instance #0 + | + |-> DMA instance #1 + . + . + | + |-> DMA instance #n + +Navigator DMA properties: +Required properties: + - compatible: Should be "ti,keystone-navigator-dma" + - clocks: phandle to dma instances clocks. The clock handles can be as + many as the dma instances. The order should be maintained as per + the dma instances. + - ti,navigator-cloud-address: Should contain base address for the multi-core + navigator cloud and number of addresses depends on SOC integration + configuration.. Navigator cloud global address needs to be programmed + into DMA and the DMA uses it as the physical addresses to reach queue + managers. Note that these addresses though points to queue managers, + they are relevant only from DMA perspective. The QMSS may not choose to + use them since it has a different address space view to reach all + its components. + +DMA instance properties: +Required properties: + - reg: Should contain register location and length of the following dma + register regions. Register regions should be specified in the following + order. + - Global control register region (global). + - Tx DMA channel configuration register region (txchan). + - Rx DMA channel configuration register region (rxchan). + - Tx DMA channel Scheduler configuration register region (txsched). + - Rx DMA flow configuration register region (rxflow). + +Optional properties: + - reg-names: Names for the register regions. + - ti,enable-all: Enable all DMA channels vs clients opening specific channels + what they need. This property is useful for the userspace fast path + case where the linux drivers enables the channels used by userland + stack. + - ti,loop-back: To loopback Tx streaming I/F to Rx streaming I/F. Used for + infrastructure transfers. + - ti,rx-retry-timeout: Number of dma cycles to wait before retry on buffer + starvation. + +Example: + + knav_dmas: knav_dmas@0 { + compatible = "ti,keystone-navigator-dma"; + clocks = <&papllclk>, <&clkxge>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + ti,navigator-cloud-address = <0x23a80000 0x23a90000 + 0x23aa0000 0x23ab0000>; + + dma_gbe: dma_gbe@0 { + reg = <0x2004000 0x100>, + <0x2004400 0x120>, + <0x2004800 0x300>, + <0x2004c00 0x120>, + <0x2005000 0x400>; + reg-names = "global", "txchan", "rxchan", + "txsched", "rxflow"; + }; + + dma_xgbe: dma_xgbe@0 { + reg = <0x2fa1000 0x100>, + <0x2fa1400 0x200>, + <0x2fa1800 0x200>, + <0x2fa1c00 0x200>, + <0x2fa2000 0x400>; + reg-names = "global", "txchan", "rxchan", + "txsched", "rxflow"; + }; + }; + +Navigator DMA client: +Required properties: + - ti,navigator-dmas: List of one or more DMA specifiers, each consisting of + - A phandle pointing to DMA instance node + - A DMA channel number as a phandle arg. + - ti,navigator-dma-names: Contains dma channel name for each DMA specifier in + the 'ti,navigator-dmas' property. + +Example: + + netcp: netcp@2090000 { + .. + ti,navigator-dmas = <&dma_gbe 22>, + <&dma_gbe 23>, + <&dma_gbe 8>; + ti,navigator-dma-names = "netrx0", "netrx1", "nettx"; + .. + }; diff --git a/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt b/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt new file mode 100644 index 000000000000..d8e8cdb733f9 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt @@ -0,0 +1,232 @@ +* Texas Instruments Keystone Navigator Queue Management SubSystem driver + +The QMSS (Queue Manager Sub System) found on Keystone SOCs is one of +the main hardware sub system which forms the backbone of the Keystone +multi-core Navigator. QMSS consist of queue managers, packed-data structure +processors(PDSP), linking RAM, descriptor pools and infrastructure +Packet DMA. +The Queue Manager is a hardware module that is responsible for accelerating +management of the packet queues. Packets are queued/de-queued by writing or +reading descriptor address to a particular memory mapped location. The PDSPs +perform QMSS related functions like accumulation, QoS, or event management. +Linking RAM registers are used to link the descriptors which are stored in +descriptor RAM. Descriptor RAM is configurable as internal or external memory. +The QMSS driver manages the PDSP setups, linking RAM regions, +queue pool management (allocation, push, pop and notify) and descriptor +pool management. + + +Required properties: +- compatible : Must be "ti,keystone-navigator-qmss"; +- clocks : phandle to the reference clock for this device. +- queue-range : <start number> total range of queue numbers for the device. +- linkram0 : <address size> for internal link ram, where size is the total + link ram entries. +- linkram1 : <address size> for external link ram, where size is the total + external link ram entries. If the address is specified as "0" + driver will allocate memory. +- qmgrs : child node describing the individual queue managers on the + SoC. On keystone 1 devices there should be only one node. + On keystone 2 devices there can be more than 1 node. + -- managed-queues : the actual queues managed by each queue manager + instance, specified as <"base queue #" "# of queues">. + -- reg : Address and size of the register set for the device. + Register regions should be specified in the following + order + - Queue Peek region. + - Queue status RAM. + - Queue configuration region. + - Descriptor memory setup region. + - Queue Management/Queue Proxy region for queue Push. + - Queue Management/Queue Proxy region for queue Pop. +- queue-pools : child node classifying the queue ranges into pools. + Queue ranges are grouped into 3 type of pools: + - qpend : pool of qpend(interruptible) queues + - general-purpose : pool of general queues, primarly used + as free descriptor queues or the + transmit DMA queues. + - accumulator : pool of queues on PDSP accumulator channel + Each range can have the following properties: + -- qrange : number of queues to use per queue range, specified as + <"base queue #" "# of queues">. + -- interrupts : Optional property to specify the interrupt mapping + for interruptible queues. The driver additionaly sets + the interrupt affinity hint based on the cpu mask. + -- qalloc-by-id : Optional property to specify that the queues in this + range can only be allocated by queue id. + -- accumulator : Accumulator channel specification. Any of the PDSPs in + QMSS can be loaded with the accumulator firmware. The + accumulator firmware’s job is to poll a select number of + queues looking for descriptors that have been pushed + into them. Descriptors are popped from the queue and + placed in a buffer provided by the host. When the list + becomes full or a programmed time period expires, the + accumulator triggers an interrupt to the host to read + the buffer for descriptor information. This firmware + comes in 16, 32, and 48 channel builds. Each of these + channels can be configured to monitor 32 contiguous + queues. Accumulator channel property is specified as: + <pdsp-id, channel, entries, pacing mode, latency> + pdsp-id : QMSS PDSP running accumulator firmware + on which the channel has to be + configured + channel : Accumulator channel number + entries : Size of the accumulator descriptor list + pacing mode : Interrupt pacing mode + 0 : None, i.e interrupt on list full only + 1 : Time delay since last interrupt + 2 : Time delay since first new packet + 3 : Time delay since last new packet + latency : time to delay the interrupt, specified + in microseconds. + -- multi-queue : Optional property to specify that the channel has to + monitor upto 32 queues starting at the base queue #. +- descriptor-regions : child node describing the memory regions for keystone + navigator packet DMA descriptors. The memory for + descriptors will be allocated by the driver. + -- id : region number in QMSS. + -- region-spec : specifies the number of descriptors in the + region, specified as + <"# of descriptors" "descriptor size">. + -- link-index : start index, i.e. index of the first + descriptor in the region. + +Optional properties: +- dma-coherent : Present if DMA operations are coherent. +- pdsps : child node describing the PDSP configuration. + -- firmware : firmware to be loaded on the PDSP. + -- id : the qmss pdsp that will run the firmware. + -- reg : Address and size of the register set for the PDSP. + Register regions should be specified in the following + order + - PDSP internal RAM region. + - PDSP control/status region registers. + - QMSS interrupt distributor registers. + - PDSP command interface region. + +Example: + +qmss: qmss@2a40000 { + compatible = "ti,keystone-qmss"; + dma-coherent; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&chipclk13>; + ranges; + queue-range = <0 0x4000>; + linkram0 = <0x100000 0x8000>; + linkram1 = <0x0 0x10000>; + + qmgrs { + #address-cells = <1>; + #size-cells = <1>; + ranges; + qmgr0 { + managed-queues = <0 0x2000>; + reg = <0x2a40000 0x20000>, + <0x2a06000 0x400>, + <0x2a02000 0x1000>, + <0x2a03000 0x1000>, + <0x23a80000 0x20000>, + <0x2a80000 0x20000>; + }; + + qmgr1 { + managed-queues = <0x2000 0x2000>; + reg = <0x2a60000 0x20000>, + <0x2a06400 0x400>, + <0x2a04000 0x1000>, + <0x2a05000 0x1000>, + <0x23aa0000 0x20000>, + <0x2aa0000 0x20000>; + }; + }; + queue-pools { + qpend { + qpend-0 { + qrange = <658 8>; + interrupts =<0 40 0xf04 0 41 0xf04 0 42 0xf04 + 0 43 0xf04 0 44 0xf04 0 45 0xf04 + 0 46 0xf04 0 47 0xf04>; + }; + qpend-1 { + qrange = <8704 16>; + interrupts = <0 48 0xf04 0 49 0xf04 0 50 0xf04 + 0 51 0xf04 0 52 0xf04 0 53 0xf04 + 0 54 0xf04 0 55 0xf04 0 56 0xf04 + 0 57 0xf04 0 58 0xf04 0 59 0xf04 + 0 60 0xf04 0 61 0xf04 0 62 0xf04 + 0 63 0xf04>; + qalloc-by-id; + }; + qpend-2 { + qrange = <8720 16>; + interrupts = <0 64 0xf04 0 65 0xf04 0 66 0xf04 + 0 59 0xf04 0 68 0xf04 0 69 0xf04 + 0 70 0xf04 0 71 0xf04 0 72 0xf04 + 0 73 0xf04 0 74 0xf04 0 75 0xf04 + 0 76 0xf04 0 77 0xf04 0 78 0xf04 + 0 79 0xf04>; + }; + }; + general-purpose { + gp-0 { + qrange = <4000 64>; + }; + netcp-tx { + qrange = <640 9>; + qalloc-by-id; + }; + }; + accumulator { + acc-0 { + qrange = <128 32>; + accumulator = <0 36 16 2 50>; + interrupts = <0 215 0xf01>; + multi-queue; + qalloc-by-id; + }; + acc-1 { + qrange = <160 32>; + accumulator = <0 37 16 2 50>; + interrupts = <0 216 0xf01>; + multi-queue; + }; + acc-2 { + qrange = <192 32>; + accumulator = <0 38 16 2 50>; + interrupts = <0 217 0xf01>; + multi-queue; + }; + acc-3 { + qrange = <224 32>; + accumulator = <0 39 16 2 50>; + interrupts = <0 218 0xf01>; + multi-queue; + }; + }; + }; + descriptor-regions { + #address-cells = <1>; + #size-cells = <1>; + ranges; + region-12 { + id = <12>; + region-spec = <8192 128>; /* num_desc desc_size */ + link-index = <0x4000>; + }; + }; + pdsps { + #address-cells = <1>; + #size-cells = <1>; + ranges; + pdsp0@0x2a10000 { + firmware = "keystone/qmss_pdsp_acc48_k2_le_1_0_0_8.fw"; + reg = <0x2a10000 0x1000>, + <0x2a0f000 0x100>, + <0x2a0c000 0x3c8>, + <0x2a20000 0x4000>; + id = <0>; + }; + }; +}; /* qmss */ diff --git a/Documentation/devicetree/bindings/sound/adi,axi-spdif-tx.txt b/Documentation/devicetree/bindings/sound/adi,axi-spdif-tx.txt index 46f344965313..4eb7997674a0 100644 --- a/Documentation/devicetree/bindings/sound/adi,axi-spdif-tx.txt +++ b/Documentation/devicetree/bindings/sound/adi,axi-spdif-tx.txt @@ -1,7 +1,7 @@ ADI AXI-SPDIF controller Required properties: - - compatible : Must be "adi,axi-spdif-1.00.a" + - compatible : Must be "adi,axi-spdif-tx-1.00.a" - reg : Must contain SPDIF core's registers location and length - clocks : Pairs of phandle and specifier referencing the controller's clocks. The controller expects two clocks, the clock used for the AXI interface and diff --git a/Documentation/devicetree/bindings/sound/adi,ssm2602.txt b/Documentation/devicetree/bindings/sound/adi,ssm2602.txt new file mode 100644 index 000000000000..3b3302fe399b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/adi,ssm2602.txt @@ -0,0 +1,19 @@ +Analog Devices SSM2602, SSM2603 and SSM2604 I2S audio CODEC devices + +SSM2602 support both I2C and SPI as the configuration interface, +the selection is made by the MODE strap-in pin. +SSM2603 and SSM2604 only support I2C as the configuration interface. + +Required properties: + + - compatible : One of "adi,ssm2602", "adi,ssm2603" or "adi,ssm2604" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + + Example: + + ssm2602: ssm2602@1a { + compatible = "adi,ssm2602"; + reg = <0x1a>; + }; diff --git a/Documentation/devicetree/bindings/sound/ak4104.txt b/Documentation/devicetree/bindings/sound/ak4104.txt index b902ee39cf89..deca5e18f304 100644 --- a/Documentation/devicetree/bindings/sound/ak4104.txt +++ b/Documentation/devicetree/bindings/sound/ak4104.txt @@ -8,6 +8,8 @@ Required properties: - reg : The chip select number on the SPI bus + - vdd-supply : A regulator node, providing 2.7V - 3.6V + Optional properties: - reset-gpio : a GPIO spec for the reset pin. If specified, it will be @@ -19,4 +21,5 @@ spdif: ak4104@0 { compatible = "asahi-kasei,ak4104"; reg = <0>; spi-max-frequency = <5000000>; + vdd-supply = <&vdd_3v3_reg>; }; diff --git a/Documentation/devicetree/bindings/sound/ak5386.txt b/Documentation/devicetree/bindings/sound/ak5386.txt index dc3914fe6ce8..ec3df3abba0c 100644 --- a/Documentation/devicetree/bindings/sound/ak5386.txt +++ b/Documentation/devicetree/bindings/sound/ak5386.txt @@ -10,10 +10,14 @@ Optional properties: - reset-gpio : a GPIO spec for the reset/power down pin. If specified, it will be deasserted at probe time. + - va-supply : a regulator spec, providing 5.0V + - vd-supply : a regulator spec, providing 3.3V Example: spdif: ak5386@0 { compatible = "asahi-kasei,ak5386"; reset-gpio = <&gpio0 23>; + va-supply = <&vdd_5v0_reg>; + vd-supply = <&vdd_3v3_reg>; }; diff --git a/Documentation/devicetree/bindings/sound/alc5623.txt b/Documentation/devicetree/bindings/sound/alc5623.txt new file mode 100644 index 000000000000..26c86c98d671 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/alc5623.txt @@ -0,0 +1,25 @@ +ALC5621/ALC5622/ALC5623 audio Codec + +Required properties: + + - compatible: "realtek,alc5623" + - reg: the I2C address of the device. + +Optional properties: + + - add-ctrl: Default register value for Reg-40h, Additional Control + Register. If absent or has the value of 0, the + register is untouched. + + - jack-det-ctrl: Default register value for Reg-5Ah, Jack Detect + Control Register. If absent or has value 0, the + register is untouched. + +Example: + + alc5621: alc5621@1a { + compatible = "alc5621"; + reg = <0x1a>; + add-ctrl = <0x3700>; + jack-det-ctrl = <0x4810>; + }; diff --git a/Documentation/devicetree/bindings/sound/armada-370db-audio.txt b/Documentation/devicetree/bindings/sound/armada-370db-audio.txt new file mode 100644 index 000000000000..bf984d238620 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/armada-370db-audio.txt @@ -0,0 +1,27 @@ +Device Tree bindings for the Armada 370 DB audio +================================================ + +These Device Tree bindings are used to describe the audio complex +found on the Armada 370 DB platform. + +Mandatory properties: + + * compatible: must be "marvell,a370db-audio" + + * marvell,audio-controller: a phandle that points to the audio + controller of the Armada 370 SoC. + + * marvell,audio-codec: a set of three phandles that points to: + + 1/ the analog audio codec connected to the Armada 370 SoC + 2/ the S/PDIF transceiver + 3/ the S/PDIF receiver + +Example: + + sound { + compatible = "marvell,a370db-audio"; + marvell,audio-controller = <&audio_controller>; + marvell,audio-codec = <&audio_codec &spdif_out &spdif_in>; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/sound/cs35l32.txt b/Documentation/devicetree/bindings/sound/cs35l32.txt new file mode 100644 index 000000000000..1417d3f5cc22 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs35l32.txt @@ -0,0 +1,62 @@ +CS35L32 audio CODEC + +Required properties: + + - compatible : "cirrus,cs35l32" + + - reg : the I2C address of the device for I2C. Address is determined by the level + of the AD0 pin. Level 0 is 0x40 while Level 1 is 0x41. + + - VA-supply, VP-supply : power supplies for the device, + as covered in Documentation/devicetree/bindings/regulator/regulator.txt. + +Optional properties: + + - reset-gpios : a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the codec starts. + + - cirrus,boost-manager : Boost voltage control. + 0 = Automatically managed. Boost-converter output voltage is the higher + of the two: Class G or adaptive LED voltage. + 1 = Automatically managed irrespective of audio, adapting for low-power + dissipation when LEDs are ON, and operating in Fixed-Boost Bypass Mode + if LEDs are OFF (VBST = VP). + 2 = (Default) Boost voltage fixed in Bypass Mode (VBST = VP). + 3 = Boost voltage fixed at 5 V. + + - cirrus,sdout-datacfg : Data configuration for dual CS35L32 applications only. + Determines the data packed in a two-CS35L32 configuration. + 0 = Left/right channels VMON[11:0], IMON[11:0], VPMON[7:0]. + 1 = Left/right channels VMON[11:0], IMON[11:0], STATUS. + 2 = (Default) left/right channels VMON[15:0], IMON [15:0]. + 3 = Left/right channels VPMON[7:0], STATUS. + + - cirrus,sdout-share : SDOUT sharing. Determines whether one or two CS35L32 + devices are on board sharing SDOUT. + 0 = (Default) One IC. + 1 = Two IC's. + + - cirrus,battery-recovery : Low battery nominal recovery threshold, rising VP. + 0 = 3.1V + 1 = 3.2V + 2 = 3.3V (Default) + 3 = 3.4V + + - cirrus,battery-threshold : Low battery nominal threshold, falling VP. + 0 = 3.1V + 1 = 3.2V + 2 = 3.3V + 3 = 3.4V (Default) + 4 = 3.5V + 5 = 3.6V + +Example: + +codec: codec@40 { + compatible = "cirrus,cs35l32"; + reg = <0x40>; + reset-gpios = <&gpio 10 0>; + cirrus,boost-manager = <0x03>; + cirrus,sdout-datacfg = <0x02>; + VA-supply = <®_audio>; +}; diff --git a/Documentation/devicetree/bindings/sound/cs4265.txt b/Documentation/devicetree/bindings/sound/cs4265.txt new file mode 100644 index 000000000000..380fff8e4e83 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs4265.txt @@ -0,0 +1,29 @@ +CS4265 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "cirrus,cs4265" + + - reg : the I2C address of the device for I2C. The I2C address depends on + the state of the AD0 pin. If AD0 is high, the i2c address is 0x4f. + If it is low, the i2c address is 0x4e. + +Optional properties: + + - reset-gpios : a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the codec starts. + +Examples: + +codec_ad0_high: cs4265@4f { /* AD0 Pin is high */ + compatible = "cirrus,cs4265"; + reg = <0x4f>; +}; + + +codec_ad0_low: cs4265@4e { /* AD0 Pin is low */ + compatible = "cirrus,cs4265"; + reg = <0x4e>; +}; diff --git a/Documentation/devicetree/bindings/sound/cs42l56.txt b/Documentation/devicetree/bindings/sound/cs42l56.txt new file mode 100644 index 000000000000..4feb0eb27ea4 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs42l56.txt @@ -0,0 +1,63 @@ +CS42L52 audio CODEC + +Required properties: + + - compatible : "cirrus,cs42l56" + + - reg : the I2C address of the device for I2C + + - VA-supply, VCP-supply, VLDO-supply : power supplies for the device, + as covered in Documentation/devicetree/bindings/regulator/regulator.txt. + +Optional properties: + + - cirrus,gpio-nreset : GPIO controller's phandle and the number + of the GPIO used to reset the codec. + + - cirrus,chgfreq-divisor : Values used to set the Charge Pump Frequency. + Allowable values of 0x00 through 0x0F. These are raw values written to the + register, not the actual frequency. The frequency is determined by the following. + Frequency = MCLK / 4 * (N+2) + N = chgfreq_val + MCLK = Where MCLK is the frequency of the mclk signal after the MCLKDIV2 circuit. + + - cirrus,ain1a-ref-cfg, ain1b-ref-cfg : boolean, If present, AIN1A or AIN1B are configured + as a pseudo-differential input referenced to AIN1REF/AIN3A. + + - cirrus,ain2a-ref-cfg, ain2b-ref-cfg : boolean, If present, AIN2A or AIN2B are configured + as a pseudo-differential input referenced to AIN2REF/AIN3B. + + - cirrus,micbias-lvl: Set the output voltage level on the MICBIAS Pin. + 0 = 0.5 x VA + 1 = 0.6 x VA + 2 = 0.7 x VA + 3 = 0.8 x VA + 4 = 0.83 x VA + 5 = 0.91 x VA + + - cirrus,adaptive-pwr-cfg : Configures how the power to the Headphone and Lineout + Amplifiers adapt to the output signal levels. + 0 = Adapt to Volume Mode. Voltage level determined by the sum of the relevant volume settings. + 1 = Fixed - Headphone and Line Amp supply = + or - VCP/2. + 2 = Fixed - Headphone and Line Amp supply = + or - VCP. + 3 = Adapted to Signal; Voltage level is dynamically determined by the output signal. + + - cirrus,hpf-left-freq, hpf-right-freq : Sets the corner frequency (-3dB point) for the internal High-Pass + Filter. + 0 = 1.8Hz + 1 = 119Hz + 2 = 236Hz + 3 = 464Hz + + +Example: + +codec: codec@4b { + compatible = "cirrus,cs42l56"; + reg = <0x4b>; + gpio-reset = <&gpio 10 0>; + cirrus,chgfreq-divisor = <0x05>; + cirrus.ain1_ref_cfg; + cirrus,micbias-lvl = <5>; + VA-supply = <®_audio>; +}; diff --git a/Documentation/devicetree/bindings/sound/cs42xx8.txt b/Documentation/devicetree/bindings/sound/cs42xx8.txt new file mode 100644 index 000000000000..f631fbca6284 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs42xx8.txt @@ -0,0 +1,28 @@ +CS42448/CS42888 audio CODEC + +Required properties: + + - compatible : must contain one of "cirrus,cs42448" and "cirrus,cs42888" + + - reg : the I2C address of the device for I2C + + - clocks : a list of phandles + clock-specifiers, one for each entry in + clock-names + + - clock-names : must contain "mclk" + + - VA-supply, VD-supply, VLS-supply, VLC-supply: power supplies for the device, + as covered in Documentation/devicetree/bindings/regulator/regulator.txt + +Example: + +codec: cs42888@48 { + compatible = "cirrus,cs42888"; + reg = <0x48>; + clocks = <&codec_mclk 0>; + clock-names = "mclk"; + VA-supply = <®_audio>; + VD-supply = <®_audio>; + VLS-supply = <®_audio>; + VLC-supply = <®_audio>; +}; diff --git a/Documentation/devicetree/bindings/sound/da9055.txt b/Documentation/devicetree/bindings/sound/da9055.txt new file mode 100644 index 000000000000..ed1b7cc6f249 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/da9055.txt @@ -0,0 +1,22 @@ +* Dialog DA9055 Audio CODEC + +DA9055 provides Audio CODEC support (I2C only). + +The Audio CODEC device in DA9055 has it's own I2C address which is configurable, +so the device is instantiated separately from the PMIC (MFD) device. + +For details on accompanying PMIC I2C device, see the following: +Documentation/devicetree/bindings/mfd/da9055.txt + +Required properties: + + - compatible: "dlg,da9055-codec" + - reg: Specifies the I2C slave address + + +Example: + + codec: da9055-codec@1a { + compatible = "dlg,da9055-codec"; + reg = <0x1a>; + }; diff --git a/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt b/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt index 865178d5cdf3..963e100514c2 100644 --- a/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt +++ b/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt @@ -5,12 +5,19 @@ Required properties: - ti,model : The user-visible name of this sound complex. - ti,audio-codec : The phandle of the TLV320AIC3x audio codec - ti,mcasp-controller : The phandle of the McASP controller -- ti,codec-clock-rate : The Codec Clock rate (in Hz) applied to the Codec - ti,audio-routing : A list of the connections between audio components. Each entry is a pair of strings, the first being the connection's sink, the second being the connection's source. Valid names for sources and sinks are the codec's pins, and the jacks on the board: +Optional properties: +- ti,codec-clock-rate : The Codec Clock rate (in Hz) applied to the Codec. +- clocks : Reference to the master clock +- clock-names : The clock should be named "mclk" +- Either codec-clock-rate or the codec-clock reference has to be defined. If + the both are defined the driver attempts to set referenced clock to the + defined rate and takes the rate from the clock reference. + Board connectors: * Headphone Jack diff --git a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt index 569b26c4a81e..60ca07996458 100644 --- a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt +++ b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt @@ -47,7 +47,7 @@ mcasp0: mcasp0@1d00000 { reg = <0x100000 0x3000>; reg-names "mpu"; interrupts = <82>, <83>; - interrupts-names = "tx", "rx"; + interrupt-names = "tx", "rx"; op-mode = <0>; /* MCASP_IIS_MODE */ tdm-slots = <2>; serial-dir = < diff --git a/Documentation/devicetree/bindings/sound/es8328.txt b/Documentation/devicetree/bindings/sound/es8328.txt new file mode 100644 index 000000000000..30ea8a318ae9 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/es8328.txt @@ -0,0 +1,38 @@ +Everest ES8328 audio CODEC + +This device supports both I2C and SPI. + +Required properties: + + - compatible : "everest,es8328" + - DVDD-supply : Regulator providing digital core supply voltage 1.8 - 3.6V + - AVDD-supply : Regulator providing analog supply voltage 3.3V + - PVDD-supply : Regulator providing digital IO supply voltage 1.8 - 3.6V + - IPVDD-supply : Regulator providing analog output voltage 3.3V + - clocks : A 22.5792 or 11.2896 MHz clock + - reg : the I2C address of the device for I2C, the chip select number for SPI + +Pins on the device (for linking into audio routes): + + * LOUT1 + * LOUT2 + * ROUT1 + * ROUT2 + * LINPUT1 + * RINPUT1 + * LINPUT2 + * RINPUT2 + * Mic Bias + + +Example: + +codec: es8328@11 { + compatible = "everest,es8328"; + DVDD-supply = <®_3p3v>; + AVDD-supply = <®_3p3v>; + PVDD-supply = <®_3p3v>; + HPVDD-supply = <®_3p3v>; + clocks = <&clks 169>; + reg = <0x11>; +}; diff --git a/Documentation/devicetree/bindings/sound/eukrea-tlv320.txt b/Documentation/devicetree/bindings/sound/eukrea-tlv320.txt new file mode 100644 index 000000000000..0d7985c864af --- /dev/null +++ b/Documentation/devicetree/bindings/sound/eukrea-tlv320.txt @@ -0,0 +1,21 @@ +Audio complex for Eukrea boards with tlv320aic23 codec. + +Required properties: +- compatible : "eukrea,asoc-tlv320" +- eukrea,model : The user-visible name of this sound complex. +- ssi-controller : The phandle of the SSI controller. +- fsl,mux-int-port : The internal port of the i.MX audio muxer (AUDMUX). +- fsl,mux-ext-port : The external port of the i.MX audio muxer. + +Note: The AUDMUX port numbering should start at 1, which is consistent with +hardware manual. + +Example: + + sound { + compatible = "eukrea,asoc-tlv320"; + eukrea,model = "imx51-eukrea-tlv320aic23"; + ssi-controller = <&ssi2>; + fsl,mux-int-port = <2>; + fsl,mux-ext-port = <3>; + }; diff --git a/Documentation/devicetree/bindings/sound/fsl,asrc.txt b/Documentation/devicetree/bindings/sound/fsl,asrc.txt new file mode 100644 index 000000000000..b93362a570be --- /dev/null +++ b/Documentation/devicetree/bindings/sound/fsl,asrc.txt @@ -0,0 +1,60 @@ +Freescale Asynchronous Sample Rate Converter (ASRC) Controller + +The Asynchronous Sample Rate Converter (ASRC) converts the sampling rate of a +signal associated with an input clock into a signal associated with a different +output clock. The driver currently works as a Front End of DPCM with other Back +Ends Audio controller such as ESAI, SSI and SAI. It has three pairs to support +three substreams within totally 10 channels. + +Required properties: + + - compatible : Contains "fsl,imx35-asrc" or "fsl,imx53-asrc". + + - reg : Offset and length of the register set for the device. + + - interrupts : Contains the spdif interrupt. + + - dmas : Generic dma devicetree binding as described in + Documentation/devicetree/bindings/dma/dma.txt. + + - dma-names : Contains "rxa", "rxb", "rxc", "txa", "txb" and "txc". + + - clocks : Contains an entry for each entry in clock-names. + + - clock-names : Contains the following entries + "mem" Peripheral access clock to access registers. + "ipg" Peripheral clock to driver module. + "asrck_<0-f>" Clock sources for input and output clock. + + - big-endian : If this property is absent, the little endian mode + will be in use as default. Otherwise, the big endian + mode will be in use for all the device registers. + + - fsl,asrc-rate : Defines a mutual sample rate used by DPCM Back Ends. + + - fsl,asrc-width : Defines a mutual sample width used by DPCM Back Ends. + +Example: + +asrc: asrc@02034000 { + compatible = "fsl,imx53-asrc"; + reg = <0x02034000 0x4000>; + interrupts = <0 50 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks 107>, <&clks 107>, <&clks 0>, + <&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>, + <&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>, + <&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>, + <&clks 107>, <&clks 0>, <&clks 0>; + clock-names = "mem", "ipg", "asrck0", + "asrck_1", "asrck_2", "asrck_3", "asrck_4", + "asrck_5", "asrck_6", "asrck_7", "asrck_8", + "asrck_9", "asrck_a", "asrck_b", "asrck_c", + "asrck_d", "asrck_e", "asrck_f"; + dmas = <&sdma 17 23 1>, <&sdma 18 23 1>, <&sdma 19 23 1>, + <&sdma 20 23 1>, <&sdma 21 23 1>, <&sdma 22 23 1>; + dma-names = "rxa", "rxb", "rxc", + "txa", "txb", "txc"; + fsl,asrc-rate = <48000>; + fsl,asrc-width = <16>; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/sound/fsl,esai.txt b/Documentation/devicetree/bindings/sound/fsl,esai.txt index d7b99fa637b5..52f5b6bf3e8e 100644 --- a/Documentation/devicetree/bindings/sound/fsl,esai.txt +++ b/Documentation/devicetree/bindings/sound/fsl,esai.txt @@ -7,7 +7,8 @@ other DSPs. It has up to six transmitters and four receivers. Required properties: - - compatible : Compatible list, must contain "fsl,imx35-esai". + - compatible : Compatible list, must contain "fsl,imx35-esai" or + "fsl,vf610-esai" - reg : Offset and length of the register set for the device. @@ -34,6 +35,10 @@ Required properties: that ESAI would work in the synchronous mode, which means all the settings for Receiving would be duplicated from Transmition related registers. + - big-endian : If this property is absent, the native endian mode will + be in use as default, or the big endian mode will be in use for all the + device registers. + Example: esai: esai@02024000 { @@ -46,5 +51,6 @@ esai: esai@02024000 { dma-names = "rx", "tx"; fsl,fifo-depth = <128>; fsl,esai-synchronous; + big-endian; status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/sound/fsl,spdif.txt b/Documentation/devicetree/bindings/sound/fsl,spdif.txt index f2ae335670f5..3e9e82c8eab3 100644 --- a/Documentation/devicetree/bindings/sound/fsl,spdif.txt +++ b/Documentation/devicetree/bindings/sound/fsl,spdif.txt @@ -29,6 +29,10 @@ Required properties: can also be referred to TxClk_Source bit of register SPDIF_STC. + - big-endian : If this property is absent, the native endian mode will + be in use as default, or the big endian mode will be in use for all the + device registers. + Example: spdif: spdif@02004000 { @@ -50,5 +54,6 @@ spdif: spdif@02004000 { "rxtx5", "rxtx6", "rxtx7"; + big-endian; status = "okay"; }; diff --git a/Documentation/devicetree/bindings/sound/fsl,ssi.txt b/Documentation/devicetree/bindings/sound/fsl,ssi.txt index b93e9a91e30e..5b76be45d18b 100644 --- a/Documentation/devicetree/bindings/sound/fsl,ssi.txt +++ b/Documentation/devicetree/bindings/sound/fsl,ssi.txt @@ -20,15 +20,6 @@ Required properties: have. - interrupt-parent: The phandle for the interrupt controller that services interrupts for this device. -- fsl,mode: The operating mode for the SSI interface. - "i2s-slave" - I2S mode, SSI is clock slave - "i2s-master" - I2S mode, SSI is clock master - "lj-slave" - left-justified mode, SSI is clock slave - "lj-master" - l.j. mode, SSI is clock master - "rj-slave" - right-justified mode, SSI is clock slave - "rj-master" - r.j., SSI is clock master - "ac97-slave" - AC97 mode, SSI is clock slave - "ac97-master" - AC97 mode, SSI is clock master - fsl,playback-dma: Phandle to a node for the DMA channel to use for playback of audio. This is typically dictated by SOC design. See the notes below. @@ -47,6 +38,9 @@ Required properties: be connected together, and SRFS and STFS be connected together. This would still allow different sample sizes, but not different sample rates. + - clocks: "ipg" - Required clock for the SSI unit + "baud" - Required clock for SSI master mode. Otherwise this + clock is not used Required are also ac97 link bindings if ac97 is used. See Documentation/devicetree/bindings/sound/soc-ac97link.txt for the necessary @@ -64,6 +58,9 @@ Optional properties: Documentation/devicetree/bindings/dma/dma.txt. - dma-names: Two dmas have to be defined, "tx" and "rx", if fsl,imx-fiq is not defined. +- fsl,mode: The operating mode for the AC97 interface only. + "ac97-slave" - AC97 mode, SSI is clock slave + "ac97-master" - AC97 mode, SSI is clock master Child 'codec' node required properties: - compatible: Compatible list, contains the name of the codec diff --git a/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt b/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt new file mode 100644 index 000000000000..a96774c194c8 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt @@ -0,0 +1,82 @@ +Freescale Generic ASoC Sound Card with ASRC support + +The Freescale Generic ASoC Sound Card can be used, ideally, for all Freescale +SoCs connecting with external CODECs. + +The idea of this generic sound card is a bit like ASoC Simple Card. However, +for Freescale SoCs (especially those released in recent years), most of them +have ASRC (Documentation/devicetree/bindings/sound/fsl,asrc.txt) inside. And +this is a specific feature that might be painstakingly controlled and merged +into the Simple Card. + +So having this generic sound card allows all Freescale SoC users to benefit +from the simplification of a new card support and the capability of the wide +sample rates support through ASRC. + +Note: The card is initially designed for those sound cards who use I2S and + PCM DAI formats. However, it'll be also possible to support those non + I2S/PCM type sound cards, such as S/PDIF audio and HDMI audio, as long + as the driver has been properly upgraded. + + +The compatible list for this generic sound card currently: + "fsl,imx-audio-cs42888" + + "fsl,imx-audio-wm8962" + (compatible with Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt) + + "fsl,imx-audio-sgtl5000" + (compatible with Documentation/devicetree/bindings/sound/imx-audio-sgtl5000.txt) + +Required properties: + + - compatible : Contains one of entries in the compatible list. + + - model : The user-visible name of this sound complex + + - audio-cpu : The phandle of an CPU DAI controller + + - audio-codec : The phandle of an audio codec + + - audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source. There're a few pre-designed board connectors: + * Line Out Jack + * Line In Jack + * Headphone Jack + * Mic Jack + * Ext Spk + * AMIC (stands for Analog Microphone Jack) + * DMIC (stands for Digital Microphone Jack) + + Note: The "Mic Jack" and "AMIC" are redundant while + coexsiting in order to support the old bindings + of wm8962 and sgtl5000. + +Optional properties: + + - audio-asrc : The phandle of ASRC. It can be absent if there's no + need to add ASRC support via DPCM. + +Example: +sound-cs42888 { + compatible = "fsl,imx-audio-cs42888"; + model = "cs42888-audio"; + audio-cpu = <&esai>; + audio-asrc = <&asrc>; + audio-codec = <&cs42888>; + audio-routing = + "Line Out Jack", "AOUT1L", + "Line Out Jack", "AOUT1R", + "Line Out Jack", "AOUT2L", + "Line Out Jack", "AOUT2R", + "Line Out Jack", "AOUT3L", + "Line Out Jack", "AOUT3R", + "Line Out Jack", "AOUT4L", + "Line Out Jack", "AOUT4R", + "AIN1L", "Line In Jack", + "AIN1R", "Line In Jack", + "AIN2L", "Line In Jack", + "AIN2R", "Line In Jack"; +}; diff --git a/Documentation/devicetree/bindings/sound/fsl-sai.txt b/Documentation/devicetree/bindings/sound/fsl-sai.txt index 98611a6761c0..4956b14d4b06 100644 --- a/Documentation/devicetree/bindings/sound/fsl-sai.txt +++ b/Documentation/devicetree/bindings/sound/fsl-sai.txt @@ -7,22 +7,37 @@ codec/DSP interfaces. Required properties: -- compatible: Compatible list, contains "fsl,vf610-sai". +- compatible: Compatible list, contains "fsl,vf610-sai" or "fsl,imx6sx-sai". - reg: Offset and length of the register set for the device. - clocks: Must contain an entry for each entry in clock-names. -- clock-names : Must include the "sai" entry. +- clock-names : Must include the "bus" for register access and "mclk1" "mclk2" + "mclk3" for bit clock and frame clock providing. - dmas : Generic dma devicetree binding as described in Documentation/devicetree/bindings/dma/dma.txt. - dma-names : Two dmas have to be defined, "tx" and "rx". - pinctrl-names: Must contain a "default" entry. - pinctrl-NNN: One property must exist for each entry in pinctrl-names. See ../pinctrl/pinctrl-bindings.txt for details of the property values. -- big-endian-regs: If this property is absent, the little endian mode will - be in use as default, or the big endian mode will be in use for all the - device registers. -- big-endian-data: If this property is absent, the little endian mode will - be in use as default, or the big endian mode will be in use for all the - fifo data. +- big-endian: Boolean property, required if all the FTM_PWM registers + are big-endian rather than little-endian. +- lsb-first: Configures whether the LSB or the MSB is transmitted first for + the fifo data. If this property is absent, the MSB is transmitted first as + default, or the LSB is transmitted first. +- fsl,sai-synchronous-rx: This is a boolean property. If present, indicating + that SAI will work in the synchronous mode (sync Tx with Rx) which means + both the transimitter and receiver will send and receive data by following + receiver's bit clocks and frame sync clocks. +- fsl,sai-asynchronous: This is a boolean property. If present, indicating + that SAI will work in the asynchronous mode, which means both transimitter + and receiver will send and receive data by following their own bit clocks + and frame sync clocks separately. + +Note: +- If both fsl,sai-asynchronous and fsl,sai-synchronous-rx are absent, the + default synchronous mode (sync Rx with Tx) will be used, which means both + transimitter and receiver will send and receive data by following clocks + of transimitter. +- fsl,sai-asynchronous and fsl,sai-synchronous-rx are exclusive. Example: sai2: sai@40031000 { @@ -30,11 +45,13 @@ sai2: sai@40031000 { reg = <0x40031000 0x1000>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_sai2_1>; - clocks = <&clks VF610_CLK_SAI2>; - clock-names = "sai"; + clocks = <&clks VF610_CLK_PLATFORM_BUS>, + <&clks VF610_CLK_SAI2>, + <&clks 0>, <&clks 0>; + clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 0 VF610_EDMA_MUXID0_SAI2_TX>, <&edma0 0 VF610_EDMA_MUXID0_SAI2_RX>; - big-endian-regs; - big-endian-data; + big-endian; + lsb-first; }; diff --git a/Documentation/devicetree/bindings/sound/imx-audio-es8328.txt b/Documentation/devicetree/bindings/sound/imx-audio-es8328.txt new file mode 100644 index 000000000000..07b68ab206fb --- /dev/null +++ b/Documentation/devicetree/bindings/sound/imx-audio-es8328.txt @@ -0,0 +1,60 @@ +Freescale i.MX audio complex with ES8328 codec + +Required properties: +- compatible : "fsl,imx-audio-es8328" +- model : The user-visible name of this sound complex +- ssi-controller : The phandle of the i.MX SSI controller +- jack-gpio : Optional GPIO for headphone jack +- audio-amp-supply : Power regulator for speaker amps +- audio-codec : The phandle of the ES8328 audio codec +- audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source. Valid names could be power supplies, ES8328 + pins, and the jacks on the board: + + Power supplies: + * audio-amp + + ES8328 pins: + * LOUT1 + * LOUT2 + * ROUT1 + * ROUT2 + * LINPUT1 + * LINPUT2 + * RINPUT1 + * RINPUT2 + * Mic PGA + + Board connectors: + * Headphone + * Speaker + * Mic Jack +- mux-int-port : The internal port of the i.MX audio muxer (AUDMUX) +- mux-ext-port : The external port of the i.MX audio muxer (AUDMIX) + +Note: The AUDMUX port numbering should start at 1, which is consistent with +hardware manual. + +Example: + +sound { + compatible = "fsl,imx-audio-es8328"; + model = "imx-audio-es8328"; + ssi-controller = <&ssi1>; + audio-codec = <&codec>; + jack-gpio = <&gpio5 15 0>; + audio-amp-supply = <®_audio_amp>; + audio-routing = + "Speaker", "LOUT2", + "Speaker", "ROUT2", + "Speaker", "audio-amp", + "Headphone", "ROUT1", + "Headphone", "LOUT1", + "LINPUT1", "Mic Jack", + "RINPUT1", "Mic Jack", + "Mic Jack", "Mic Bias"; + mux-int-port = <1>; + mux-ext-port = <3>; +}; diff --git a/Documentation/devicetree/bindings/sound/max98090.txt b/Documentation/devicetree/bindings/sound/max98090.txt index e4c8b36dcf89..c454e67f54bb 100644 --- a/Documentation/devicetree/bindings/sound/max98090.txt +++ b/Documentation/devicetree/bindings/sound/max98090.txt @@ -4,12 +4,18 @@ This device supports I2C only. Required properties: -- compatible : "maxim,max98090". +- compatible : "maxim,max98090" or "maxim,max98091". - reg : The I2C address of the device. - interrupts : The CODEC's interrupt output. +Optional properties: + +- clocks: The phandle of the master clock to the CODEC + +- clock-names: Should be "mclk" + Pins on the device (for linking into audio routes): * MIC1 diff --git a/Documentation/devicetree/bindings/sound/max98095.txt b/Documentation/devicetree/bindings/sound/max98095.txt new file mode 100644 index 000000000000..318a4c82f17f --- /dev/null +++ b/Documentation/devicetree/bindings/sound/max98095.txt @@ -0,0 +1,22 @@ +MAX98095 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : "maxim,max98095". + +- reg : The I2C address of the device. + +Optional properties: + +- clocks: The phandle of the master clock to the CODEC + +- clock-names: Should be "mclk" + +Example: + +max98095: codec@11 { + compatible = "maxim,max98095"; + reg = <0x11>; +}; diff --git a/Documentation/devicetree/bindings/sound/mvebu-audio.txt b/Documentation/devicetree/bindings/sound/mvebu-audio.txt index f0062c5871b4..cb8c07c81ce4 100644 --- a/Documentation/devicetree/bindings/sound/mvebu-audio.txt +++ b/Documentation/devicetree/bindings/sound/mvebu-audio.txt @@ -5,6 +5,7 @@ Required properties: - compatible: "marvell,kirkwood-audio" for Kirkwood platforms "marvell,dove-audio" for Dove platforms + "marvell,armada370-audio" for Armada 370 platforms - reg: physical base address of the controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/sound/nokia,rx51.txt b/Documentation/devicetree/bindings/sound/nokia,rx51.txt new file mode 100644 index 000000000000..72f93d996273 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nokia,rx51.txt @@ -0,0 +1,27 @@ +* Nokia N900 audio setup + +Required properties: +- compatible: Should contain "nokia,n900-audio" +- nokia,cpu-dai: phandle for the McBSP node +- nokia,audio-codec: phandles for the main TLV320AIC3X node and the + auxiliary TLV320AIC3X node (in this order) +- nokia,headphone-amplifier: phandle for the TPA6130A2 node +- tvout-selection-gpios: GPIO for tvout selection +- jack-detection-gpios: GPIO for jack detection +- eci-switch-gpios: GPIO for ECI (Enhancement Control Interface) switch +- speaker-amplifier-gpios: GPIO for speaker amplifier + +Example: + +sound { + compatible = "nokia,n900-audio"; + + nokia,cpu-dai = <&mcbsp2>; + nokia,audio-codec = <&tlv320aic3x>, <&tlv320aic3x_aux>; + nokia,headphone-amplifier = <&tpa6130a2>; + + tvout-selection-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>; /* 40 */ + jack-detection-gpios = <&gpio6 17 GPIO_ACTIVE_HIGH>; /* 177 */ + eci-switch-gpios = <&gpio6 22 GPIO_ACTIVE_HIGH>; /* 182 */ + speaker-amplifier-gpios = <&twl_gpio 7 GPIO_ACTIVE_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-max98090.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-max98090.txt index 9c7c55c71370..c949abc2992f 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-max98090.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-max98090.txt @@ -25,6 +25,7 @@ Required properties: Optional properties: - nvidia,hp-det-gpios : The GPIO that detect headphones are plugged in +- nvidia,mic-det-gpios : The GPIO that detect microphones are plugged in Example: diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt new file mode 100644 index 000000000000..b4730c2822bc --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt @@ -0,0 +1,28 @@ +NVIDIA Tegra30 HDA controller + +Required properties: +- compatible : "nvidia,tegra30-hda" +- reg : Should contain the HDA registers location and length. +- interrupts : The interrupt from the HDA controller. +- clocks : Must contain an entry for each required entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names : Must include the following entries: hda, hdacodec_2x, hda2hdmi +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: hda, hdacodec_2x, hda2hdmi + +Example: + +hda@0,70030000 { + compatible = "nvidia,tegra124-hda", "nvidia,tegra30-hda"; + reg = <0x0 0x70030000 0x0 0x10000>; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA124_CLK_HDA>, + <&tegra_car TEGRA124_CLK_HDA2HDMI>, + <&tegra_car TEGRA124_CLK_HDA2CODEC_2X>; + clock-names = "hda", "hda2hdmi", "hda2codec_2x"; + resets = <&tegra_car 125>, /* hda */ + <&tegra_car 128>; /* hda2hdmi */ + <&tegra_car 111>, /* hda2codec_2x */ + reset-names = "hda", "hda2hdmi", "hda2codec_2x"; +}; diff --git a/Documentation/devicetree/bindings/sound/pcm512x.txt b/Documentation/devicetree/bindings/sound/pcm512x.txt new file mode 100644 index 000000000000..faff75e64573 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/pcm512x.txt @@ -0,0 +1,30 @@ +PCM512x audio CODECs + +These devices support both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : One of "ti,pcm5121" or "ti,pcm5122" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + + - AVDD-supply, DVDD-supply, and CPVDD-supply : power supplies for the + device, as covered in bindings/regulator/regulator.txt + +Optional properties: + + - clocks : A clock specifier for the clock connected as SCLK. If this + is absent the device will be configured to clock from BCLK. + +Example: + + pcm5122: pcm5122@4c { + compatible = "ti,pcm5122"; + reg = <0x4c>; + + AVDD-supply = <®_3v3_analog>; + DVDD-supply = <®_1v8>; + CPVDD-supply = <®_3v3>; + }; diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt new file mode 100644 index 000000000000..aa697abf337e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -0,0 +1,115 @@ +Renesas R-Car sound + +Required properties: +- compatible : "renesas,rcar_sound-gen1" if generation1 + "renesas,rcar_sound-gen2" if generation2 +- reg : Should contain the register physical address. + required register is + SRU/ADG/SSI if generation1 + SRU/ADG/SSIU/SSI if generation2 +- rcar_sound,ssi : Should contain SSI feature. + The number of SSI subnode should be same as HW. + see below for detail. +- rcar_sound,src : Should contain SRC feature. + The number of SRC subnode should be same as HW. + see below for detail. +- rcar_sound,dvc : Should contain DVC feature. + The number of DVC subnode should be same as HW. + see below for detail. +- rcar_sound,dai : DAI contents. + The number of DAI subnode should be same as HW. + see below for detail. + +SSI subnode properties: +- interrupts : Should contain SSI interrupt for PIO transfer +- shared-pin : if shared clock pin +- pio-transfer : use PIO transfer mode +- no-busif : BUSIF is not ussed when [mem -> SSI] via DMA case + +SRC subnode properties: +no properties at this point + +DAI subnode properties: +- playback : list of playback modules +- capture : list of capture modules + +Example: + +rcar_sound: rcar_sound@0xffd90000 { + #sound-dai-cells = <1>; + compatible = "renesas,rcar_sound-gen2"; + reg = <0 0xec500000 0 0x1000>, /* SCU */ + <0 0xec5a0000 0 0x100>, /* ADG */ + <0 0xec540000 0 0x1000>, /* SSIU */ + <0 0xec541000 0 0x1280>; /* SSI */ + + rcar_sound,dvc { + dvc0: dvc@0 { }; + dvc1: dvc@1 { }; + }; + + rcar_sound,src { + src0: src@0 { }; + src1: src@1 { }; + src2: src@2 { }; + src3: src@3 { }; + src4: src@4 { }; + src5: src@5 { }; + src6: src@6 { }; + src7: src@7 { }; + src8: src@8 { }; + src9: src@9 { }; + }; + + rcar_sound,ssi { + ssi0: ssi@0 { + interrupts = <0 370 IRQ_TYPE_LEVEL_HIGH>; + }; + ssi1: ssi@1 { + interrupts = <0 371 IRQ_TYPE_LEVEL_HIGH>; + }; + ssi2: ssi@2 { + interrupts = <0 372 IRQ_TYPE_LEVEL_HIGH>; + }; + ssi3: ssi@3 { + interrupts = <0 373 IRQ_TYPE_LEVEL_HIGH>; + }; + ssi4: ssi@4 { + interrupts = <0 374 IRQ_TYPE_LEVEL_HIGH>; + }; + ssi5: ssi@5 { + interrupts = <0 375 IRQ_TYPE_LEVEL_HIGH>; + }; + ssi6: ssi@6 { + interrupts = <0 376 IRQ_TYPE_LEVEL_HIGH>; + }; + ssi7: ssi@7 { + interrupts = <0 377 IRQ_TYPE_LEVEL_HIGH>; + }; + ssi8: ssi@8 { + interrupts = <0 378 IRQ_TYPE_LEVEL_HIGH>; + }; + ssi9: ssi@9 { + interrupts = <0 379 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + rcar_sound,dai { + dai0 { + playback = <&ssi5 &src5>; + capture = <&ssi6>; + }; + dai1 { + playback = <&ssi3>; + }; + dai2 { + capture = <&ssi4>; + }; + dai3 { + playback = <&ssi7>; + }; + dai4 { + capture = <&ssi8>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt new file mode 100644 index 000000000000..9b82c20b306b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt @@ -0,0 +1,37 @@ +* Rockchip I2S controller + +The I2S bus (Inter-IC sound bus) is a serial link for digital +audio data transfer between devices in the system. + +Required properties: + +- compatible: should be one of the followings + - "rockchip,rk3066-i2s": for rk3066 + - "rockchip,rk3188-i2s", "rockchip,rk3066-i2s": for rk3188 + - "rockchip,rk3288-i2s", "rockchip,rk3066-i2s": for rk3288 +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: should contain the I2S interrupt. +- #address-cells: should be 1. +- #size-cells: should be 0. +- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, + Documentation/devicetree/bindings/dma/dma.txt +- dma-names: should include "tx" and "rx". +- clocks: a list of phandle + clock-specifer pairs, one for each entry in clock-names. +- clock-names: should contain followings: + - "i2s_hclk": clock for I2S BUS + - "i2s_clk" : clock for I2S controller + +Example for rk3288 I2S controller: + +i2s@ff890000 { + compatible = "rockchip,rk3288-i2s", "rockchip,rk3066-i2s"; + reg = <0xff890000 0x10000>; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&pdma1 0>, <&pdma1 1>; + dma-names = "tx", "rx"; + clock-names = "i2s_hclk", "i2s_clk"; + clocks = <&cru HCLK_I2S0>, <&cru SCLK_I2S0>; +}; diff --git a/Documentation/devicetree/bindings/sound/rt5640.txt b/Documentation/devicetree/bindings/sound/rt5640.txt index 068a1141b06f..bac4d9ac1edc 100644 --- a/Documentation/devicetree/bindings/sound/rt5640.txt +++ b/Documentation/devicetree/bindings/sound/rt5640.txt @@ -1,10 +1,10 @@ -RT5640 audio CODEC +RT5640/RT5639 audio CODEC This device supports I2C only. Required properties: -- compatible : "realtek,rt5640". +- compatible : One of "realtek,rt5640" or "realtek,rt5639". - reg : The I2C address of the device. @@ -18,7 +18,7 @@ Optional properties: - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin. -Pins on the device (for linking into audio routes): +Pins on the device (for linking into audio routes) for RT5639/RT5640: * DMIC1 * DMIC2 @@ -31,13 +31,16 @@ Pins on the device (for linking into audio routes): * HPOR * LOUTL * LOUTR - * MONOP - * MONON * SPOLP * SPOLN * SPORP * SPORN +Additional pins on the device for RT5640: + + * MONOP + * MONON + Example: rt5640 { diff --git a/Documentation/devicetree/bindings/sound/rt5677.txt b/Documentation/devicetree/bindings/sound/rt5677.txt new file mode 100644 index 000000000000..0701b834fc73 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5677.txt @@ -0,0 +1,59 @@ +RT5677 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : "realtek,rt5677". + +- reg : The I2C address of the device. + +- interrupts : The CODEC's interrupt output. + +- gpio-controller : Indicates this device is a GPIO controller. + +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). + +Optional properties: + +- realtek,pow-ldo2-gpio : The GPIO that controls the CODEC's POW_LDO2 pin. + +- realtek,in1-differential +- realtek,in2-differential +- realtek,lout1-differential +- realtek,lout2-differential +- realtek,lout3-differential + Boolean. Indicate MIC1/2 input and LOUT1/2/3 outputs are differential, + rather than single-ended. + +Pins on the device (for linking into audio routes): + + * IN1P + * IN1N + * IN2P + * IN2N + * MICBIAS1 + * DMIC1 + * DMIC2 + * DMIC3 + * DMIC4 + * LOUT1 + * LOUT2 + * LOUT3 + +Example: + +rt5677 { + compatible = "realtek,rt5677"; + reg = <0x2c>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(W, 3) GPIO_ACTIVE_HIGH>; + + gpio-controller; + #gpio-cells = <2>; + + realtek,pow-ldo2-gpio = + <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>; + realtek,in1-differential = "true"; +}; diff --git a/Documentation/devicetree/bindings/sound/samsung,odroidx2-max98090.txt b/Documentation/devicetree/bindings/sound/samsung,odroidx2-max98090.txt new file mode 100644 index 000000000000..9148f72319e1 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/samsung,odroidx2-max98090.txt @@ -0,0 +1,35 @@ +Samsung Exynos Odroid X2/U3 audio complex with MAX98090 codec + +Required properties: + - compatible : "samsung,odroidx2-audio" - for Odroid X2 board, + "samsung,odroidu3-audio" - for Odroid U3 board + - samsung,model : the user-visible name of this sound complex + - samsung,i2s-controller : the phandle of the I2S controller + - samsung,audio-codec : the phandle of the MAX98090 audio codec + - samsung,audio-routing : a list of the connections between audio + components; each entry is a pair of strings, the first being the + connection's sink, the second being the connection's source; + valid names for sources and sinks are the MAX98090's pins (as + documented in its binding), and the jacks on the board + For Odroid X2: + * Headphone Jack + * Mic Jack + * DMIC + + For Odroid U3: + * Headphone Jack + * Speakers + +Example: + +sound { + compatible = "samsung,odroidu3-audio"; + samsung,i2s-controller = <&i2s0>; + samsung,audio-codec = <&max98090>; + samsung,model = "Odroid-X2"; + samsung,audio-routing = + "Headphone Jack", "HPL", + "Headphone Jack", "HPR", + "IN1", "Mic Jack", + "Mic Jack", "MICBIAS"; +}; diff --git a/Documentation/devicetree/bindings/sound/sgtl5000.txt b/Documentation/devicetree/bindings/sound/sgtl5000.txt index 955df60a118c..d556dcb8816b 100644 --- a/Documentation/devicetree/bindings/sound/sgtl5000.txt +++ b/Documentation/devicetree/bindings/sound/sgtl5000.txt @@ -7,10 +7,20 @@ Required properties: - clocks : the clock provider of SYS_MCLK +- VDDA-supply : the regulator provider of VDDA + +- VDDIO-supply: the regulator provider of VDDIO + +Optional properties: + +- VDDD-supply : the regulator provider of VDDD + Example: codec: sgtl5000@0a { compatible = "fsl,sgtl5000"; reg = <0x0a>; clocks = <&clks 150>; + VDDA-supply = <®_3p3v>; + VDDIO-supply = <®_3p3v>; }; diff --git a/Documentation/devicetree/bindings/sound/simple-card.txt b/Documentation/devicetree/bindings/sound/simple-card.txt index 19c84df5fffa..c3cba600bf11 100644 --- a/Documentation/devicetree/bindings/sound/simple-card.txt +++ b/Documentation/devicetree/bindings/sound/simple-card.txt @@ -1,6 +1,6 @@ Simple-Card: -Simple-Card specifies audio DAI connection of SoC <-> codec. +Simple-Card specifies audio DAI connections of SoC <-> codec. Required properties: @@ -8,18 +8,60 @@ Required properties: Optional properties: -- simple-audio-card,format : CPU/CODEC common audio format. - "i2s", "right_j", "left_j" , "dsp_a" - "dsp_b", "ac97", "pdm", "msb", "lsb" +- simple-audio-card,name : User specified audio sound card name, one string + property. +- simple-audio-card,widgets : Please refer to widgets.txt. - simple-audio-card,routing : A list of the connections between audio components. Each entry is a pair of strings, the first being the connection's sink, the second being the connection's source. +- simple-audio-card,mclk-fs : Multiplication factor between stream rate and codec + mclk. +- simple-audio-card,hp-det-gpio : Reference to GPIO that signals when + headphones are attached. +- simple-audio-card,mic-det-gpio : Reference to GPIO that signals when + a microphone is attached. + +Optional subnodes: + +- simple-audio-card,dai-link : Container for dai-link level + properties and the CPU and CODEC + sub-nodes. This container may be + omitted when the card has only one + DAI link. See the examples and the + section bellow. + +Dai-link subnode properties and subnodes: -Required subnodes: +If dai-link subnode is omitted and the subnode properties are directly +under "sound"-node the subnode property and subnode names have to be +prefixed with "simple-audio-card,"-prefix. -- simple-audio-card,cpu : CPU sub-node -- simple-audio-card,codec : CODEC sub-node +Required dai-link subnodes: + +- cpu : CPU sub-node +- codec : CODEC sub-node + +Optional dai-link subnode properties: + +- format : CPU/CODEC common audio format. + "i2s", "right_j", "left_j" , "dsp_a" + "dsp_b", "ac97", "pdm", "msb", "lsb" +- frame-master : Indicates dai-link frame master. + phandle to a cpu or codec subnode. +- bitclock-master : Indicates dai-link bit clock master. + phandle to a cpu or codec subnode. +- bitclock-inversion : bool property. Add this if the + dai-link uses bit clock inversion. +- frame-inversion : bool property. Add this if the + dai-link uses frame clock inversion. + +For backward compatibility the frame-master and bitclock-master +properties can be used as booleans in codec subnode to indicate if the +codec is the dai-link frame or bit clock master. In this case there +should be no dai-link node, the same properties should not be present +at sound-node level, and the bitclock-inversion and frame-inversion +properties should also be placed in the codec node if needed. Required CPU/CODEC subnodes properties: @@ -27,35 +69,36 @@ Required CPU/CODEC subnodes properties: Optional CPU/CODEC subnodes properties: -- format : CPU/CODEC specific audio format if needed. - see simple-audio-card,format -- frame-master : bool property. add this if subnode is frame master -- bitclock-master : bool property. add this if subnode is bitclock master -- bitclock-inversion : bool property. add this if subnode has clock inversion -- frame-inversion : bool property. add this if subnode has frame inversion +- dai-tdm-slot-num : Please refer to tdm-slot.txt. +- dai-tdm-slot-width : Please refer to tdm-slot.txt. - clocks / system-clock-frequency : specify subnode's clock if needed. it can be specified via "clocks" if system has clock node (= common clock), or "system-clock-frequency" (if system doens't support common clock) -Example: +Example 1 - single DAI link: sound { compatible = "simple-audio-card"; + simple-audio-card,name = "VF610-Tower-Sound-Card"; simple-audio-card,format = "left_j"; + simple-audio-card,bitclock-master = <&dailink0_master>; + simple-audio-card,frame-master = <&dailink0_master>; + simple-audio-card,widgets = + "Microphone", "Microphone Jack", + "Headphone", "Headphone Jack", + "Speaker", "External Speaker"; simple-audio-card,routing = - "MIC_IN", "Mic Jack", + "MIC_IN", "Microphone Jack", "Headphone Jack", "HP_OUT", - "Ext Spk", "LINE_OUT"; + "External Speaker", "LINE_OUT"; simple-audio-card,cpu { sound-dai = <&sh_fsi2 0>; }; - simple-audio-card,codec { + dailink0_master: simple-audio-card,codec { sound-dai = <&ak4648>; - bitclock-master; - frame-master; clocks = <&osc>; }; }; @@ -75,3 +118,38 @@ sh_fsi2: sh_fsi2@ec230000 { interrupt-parent = <&gic>; interrupts = <0 146 0x4>; }; + +Example 2 - many DAI links: + +sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "Cubox Audio"; + + simple-audio-card,dai-link@0 { /* I2S - HDMI */ + format = "i2s"; + cpu { + sound-dai = <&audio1 0>; + }; + codec { + sound-dai = <&tda998x 0>; + }; + }; + + simple-audio-card,dai-link@1 { /* S/PDIF - HDMI */ + cpu { + sound-dai = <&audio1 1>; + }; + codec { + sound-dai = <&tda998x 1>; + }; + }; + + simple-audio-card,dai-link@2 { /* S/PDIF - S/PDIF */ + cpu { + sound-dai = <&audio1 1>; + }; + codec { + sound-dai = <&spdif_codec>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/sirf-audio-codec.txt b/Documentation/devicetree/bindings/sound/sirf-audio-codec.txt new file mode 100644 index 000000000000..062f5ec36f9b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/sirf-audio-codec.txt @@ -0,0 +1,17 @@ +SiRF internal audio CODEC + +Required properties: + + - compatible : "sirf,atlas6-audio-codec" or "sirf,prima2-audio-codec" + + - reg : the register address of the device. + + - clocks: the clock of SiRF internal audio codec + +Example: + +audiocodec: audiocodec@b0040000 { + compatible = "sirf,atlas6-audio-codec"; + reg = <0xb0040000 0x10000>; + clocks = <&clks 27>; +}; diff --git a/Documentation/devicetree/bindings/sound/sirf-audio-port.txt b/Documentation/devicetree/bindings/sound/sirf-audio-port.txt new file mode 100644 index 000000000000..1f66de3c8f00 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/sirf-audio-port.txt @@ -0,0 +1,20 @@ +* SiRF SoC audio port + +Required properties: +- compatible: "sirf,audio-port" +- reg: Base address and size entries: +- dmas: List of DMA controller phandle and DMA request line ordered pairs. +- dma-names: Identifier string for each DMA request line in the dmas property. + These strings correspond 1:1 with the ordered pairs in dmas. + + One of the DMA channels will be responsible for transmission (should be + named "tx") and one for reception (should be named "rx"). + +Example: + +audioport: audioport@b0040000 { + compatible = "sirf,audio-port"; + reg = <0xb0040000 0x10000>; + dmas = <&dmac1 3>, <&dmac1 8>; + dma-names = "rx", "tx"; +}; diff --git a/Documentation/devicetree/bindings/sound/sirf-audio.txt b/Documentation/devicetree/bindings/sound/sirf-audio.txt new file mode 100644 index 000000000000..c88882ca3704 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/sirf-audio.txt @@ -0,0 +1,41 @@ +* SiRF atlas6 and prima2 internal audio codec and port based audio setups + +Required properties: +- compatible: "sirf,sirf-audio-card" +- sirf,audio-platform: phandle for the platform node +- sirf,audio-codec: phandle for the SiRF internal codec node + +Optional properties: +- hp-pa-gpios: Need to be present if the board need control external + headphone amplifier. +- spk-pa-gpios: Need to be present if the board need control external + speaker amplifier. +- hp-switch-gpios: Need to be present if the board capable to detect jack + insertion, removal. + +Available audio endpoints for the audio-routing table: + +Board connectors: + * Headset Stereophone + * Ext Spk + * Line In + * Mic + +SiRF internal audio codec pins: + * HPOUTL + * HPOUTR + * SPKOUT + * Ext Mic + * Mic Bias + +Example: + +sound { + compatible = "sirf,sirf-audio-card"; + sirf,audio-codec = <&audiocodec>; + sirf,audio-platform = <&audioport>; + hp-pa-gpios = <&gpio 44 0>; + spk-pa-gpios = <&gpio 46 0>; + hp-switch-gpios = <&gpio 45 0>; +}; + diff --git a/Documentation/devicetree/bindings/sound/sirf-usp.txt b/Documentation/devicetree/bindings/sound/sirf-usp.txt new file mode 100644 index 000000000000..02f85b32d359 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/sirf-usp.txt @@ -0,0 +1,27 @@ +* SiRF SoC USP module + +Required properties: +- compatible: "sirf,prima2-usp-pcm" +- reg: Base address and size entries: +- dmas: List of DMA controller phandle and DMA request line ordered pairs. +- dma-names: Identifier string for each DMA request line in the dmas property. + These strings correspond 1:1 with the ordered pairs in dmas. + + One of the DMA channels will be responsible for transmission (should be + named "tx") and one for reception (should be named "rx"). + +- clocks: USP controller clock source +- pinctrl-names: Must contain a "default" entry. +- pinctrl-NNN: One property must exist for each entry in pinctrl-names. + +Example: +usp0: usp@b0080000 { + compatible = "sirf,prima2-usp-pcm"; + reg = <0xb0080000 0x10000>; + clocks = <&clks 28>; + dmas = <&dmac1 1>, <&dmac1 2>; + dma-names = "rx", "tx"; + pinctrl-names = "default"; + pinctrl-0 = <&usp0_only_utfs_pins_a>; +}; + diff --git a/Documentation/devicetree/bindings/sound/snow.txt b/Documentation/devicetree/bindings/sound/snow.txt new file mode 100644 index 000000000000..6df74f15687f --- /dev/null +++ b/Documentation/devicetree/bindings/sound/snow.txt @@ -0,0 +1,22 @@ +Audio Binding for Snow boards + +Required properties: +- compatible : Can be one of the following, + "google,snow-audio-max98090" or + "google,snow-audio-max98091" or + "google,snow-audio-max98095" +- samsung,i2s-controller: The phandle of the Samsung I2S controller +- samsung,audio-codec: The phandle of the audio codec + +Optional: +- samsung,model: The name of the sound-card + +Example: + +sound { + compatible = "google,snow-audio-max98095"; + + samsung,model = "Snow-I2S-MAX98095"; + samsung,i2s-controller = <&i2s0>; + samsung,audio-codec = <&max98095>; +}; diff --git a/Documentation/devicetree/bindings/sound/ssm4567.txt b/Documentation/devicetree/bindings/sound/ssm4567.txt new file mode 100644 index 000000000000..ec3d9e7004b5 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ssm4567.txt @@ -0,0 +1,15 @@ +Analog Devices SSM4567 audio amplifier + +This device supports I2C only. + +Required properties: + - compatible : Must be "adi,ssm4567" + - reg : the I2C address of the device. This will either be 0x34 (LR_SEL/ADDR connected to AGND), + 0x35 (LR_SEL/ADDR connected to IOVDD) or 0x36 (LR_SEL/ADDR open). + +Example: + + ssm4567: ssm4567@34 { + compatible = "adi,ssm4567"; + reg = <0x34>; + }; diff --git a/Documentation/devicetree/bindings/sound/st,sta350.txt b/Documentation/devicetree/bindings/sound/st,sta350.txt new file mode 100644 index 000000000000..307398ef2317 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/st,sta350.txt @@ -0,0 +1,131 @@ +STA350 audio CODEC + +The driver for this device only supports I2C. + +Required properties: + + - compatible: "st,sta350" + - reg: the I2C address of the device for I2C + - reset-gpios: a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the codec starts. + + - power-down-gpios: a GPIO spec for the power down pin. If specified, + it will be deasserted before communication to the codec + starts. + + - vdd-dig-supply: regulator spec, providing 3.3V + - vdd-pll-supply: regulator spec, providing 3.3V + - vcc-supply: regulator spec, providing 5V - 26V + +Optional properties: + + - st,output-conf: number, Selects the output configuration: + 0: 2-channel (full-bridge) power, 2-channel data-out + 1: 2 (half-bridge). 1 (full-bridge) on-board power + 2: 2 Channel (Full-Bridge) Power, 1 Channel FFX + 3: 1 Channel Mono-Parallel + If parameter is missing, mode 0 will be enabled. + This property has to be specified as '/bits/ 8' value. + + - st,ch1-output-mapping: Channel 1 output mapping + - st,ch2-output-mapping: Channel 2 output mapping + - st,ch3-output-mapping: Channel 3 output mapping + 0: Channel 1 + 1: Channel 2 + 2: Channel 3 + If parameter is missing, channel 1 is chosen. + This properties have to be specified as '/bits/ 8' values. + + - st,thermal-warning-recover: + If present, thermal warning recovery is enabled. + + - st,thermal-warning-adjustment: + If present, thermal warning adjustment is enabled. + + - st,fault-detect-recovery: + If present, then fault recovery will be enabled. + + - st,ffx-power-output-mode: string + The FFX power output mode selects how the FFX output timing is + configured. Must be one of these values: + - "drop-compensation" + - "tapered-compensation" + - "full-power-mode" + - "variable-drop-compensation" (default) + + - st,drop-compensation-ns: number + Only required for "st,ffx-power-output-mode" == + "variable-drop-compensation". + Specifies the drop compensation in nanoseconds. + The value must be in the range of 0..300, and only + multiples of 20 are allowed. Default is 140ns. + + - st,overcurrent-warning-adjustment: + If present, overcurrent warning adjustment is enabled. + + - st,max-power-use-mpcc: + If present, then MPCC bits are used for MPC coefficients, + otherwise standard MPC coefficients are used. + + - st,max-power-corr: + If present, power bridge correction for THD reduction near maximum + power output is enabled. + + - st,am-reduction-mode: + If present, FFX mode runs in AM reduction mode, otherwise normal + FFX mode is used. + + - st,odd-pwm-speed-mode: + If present, PWM speed mode run on odd speed mode (341.3 kHz) on all + channels. If not present, normal PWM spped mode (384 kHz) will be used. + + - st,distortion-compensation: + If present, distortion compensation variable uses DCC coefficient. + If not present, preset DC coefficient is used. + + - st,invalid-input-detect-mute: + If present, automatic invalid input detect mute is enabled. + + - st,activate-mute-output: + If present, a mute output will be activated in ase the volume will + reach a value lower than -76 dBFS. + + - st,bridge-immediate-off: + If present, the bridge will be switched off immediately after the + power-down-gpio goes low. Otherwise, the bridge will wait for 13 + million clock cycles to pass before shutting down. + + - st,noise-shape-dc-cut: + If present, the noise-shaping technique on the DC cutoff filter are + enabled. + + - st,powerdown-master-volume: + If present, the power-down pin and I2C power-down functions will + act on the master volume. Otherwise, the functions will act on the + mute commands. + + - st,powerdown-delay-divider: + If present, the bridge power-down time will be divided by the provided + value. If not specified, a divider of 1 will be used. Allowed values + are 1, 2, 4, 8, 16, 32, 64 and 128. + This property has to be specified as '/bits/ 8' value. + +Example: + +codec: sta350@38 { + compatible = "st,sta350"; + reg = <0x1c>; + reset-gpios = <&gpio1 19 0>; + power-down-gpios = <&gpio1 16 0>; + st,output-conf = /bits/ 8 <0x3>; // set output to 2-channel + // (full-bridge) power, + // 2-channel data-out + st,ch1-output-mapping = /bits/ 8 <0>; // set channel 1 output ch 1 + st,ch2-output-mapping = /bits/ 8 <0>; // set channel 2 output ch 1 + st,ch3-output-mapping = /bits/ 8 <0>; // set channel 3 output ch 1 + st,max-power-correction; // enables power bridge + // correction for THD reduction + // near maximum power output + st,invalid-input-detect-mute; // mute if no valid digital + // audio signal is provided. +}; diff --git a/Documentation/devicetree/bindings/sound/tas2552.txt b/Documentation/devicetree/bindings/sound/tas2552.txt new file mode 100644 index 000000000000..55e2a0af5645 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tas2552.txt @@ -0,0 +1,26 @@ +Texas Instruments - tas2552 Codec module + +The tas2552 serial control bus communicates through I2C protocols + +Required properties: + - compatible - One of: + "ti,tas2552" - TAS2552 + - reg - I2C slave address + - supply-*: Required supply regulators are: + "vbat" battery voltage + "iovdd" I/O Voltage + "avdd" Analog DAC Voltage + +Optional properties: + - enable-gpio - gpio pin to enable/disable the device + +Example: + +tas2552: tas2552@41 { + compatible = "ti,tas2552"; + reg = <0x41>; + enable-gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>; +}; + +For more product information please see the link below: +http://www.ti.com/product/TAS2552 diff --git a/Documentation/devicetree/bindings/sound/tdm-slot.txt b/Documentation/devicetree/bindings/sound/tdm-slot.txt new file mode 100644 index 000000000000..6a2c84247f91 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tdm-slot.txt @@ -0,0 +1,20 @@ +TDM slot: + +This specifies audio DAI's TDM slot. + +TDM slot properties: +dai-tdm-slot-num : Number of slots in use. +dai-tdm-slot-width : Width in bits for each slot. + +For instance: + dai-tdm-slot-num = <2>; + dai-tdm-slot-width = <8>; + +And for each spcified driver, there could be one .of_xlate_tdm_slot_mask() +to specify a explicit mapping of the channels and the slots. If it's absent +the default snd_soc_of_xlate_tdm_slot_mask() will be used to generating the +tx and rx masks. + +For snd_soc_of_xlate_tdm_slot_mask(), the tx and rx masks will use a 1 bit +for an active slot as default, and the default active bits are at the LSB of +the masks. diff --git a/Documentation/devicetree/bindings/sound/ti,tas5086.txt b/Documentation/devicetree/bindings/sound/ti,tas5086.txt index d2866a0d6a26..234dad296da7 100644 --- a/Documentation/devicetree/bindings/sound/ti,tas5086.txt +++ b/Documentation/devicetree/bindings/sound/ti,tas5086.txt @@ -31,6 +31,9 @@ Optional properties: Most systems should not set any of these properties. + - avdd-supply: Power supply for AVDD, providing 3.3V + - dvdd-supply: Power supply for DVDD, providing 3.3V + Examples: i2c_bus { @@ -39,5 +42,7 @@ Examples: reg = <0x1b>; reset-gpio = <&gpio 23 0>; ti,charge-period = <156000>; + avdd-supply = <&vdd_3v3_reg>; + dvdd-supply = <&vdd_3v3_reg>; }; }; diff --git a/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt b/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt new file mode 100644 index 000000000000..eff12be5e789 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt @@ -0,0 +1,61 @@ +Texas Instruments - tlv320aic31xx Codec module + +The tlv320aic31xx serial control bus communicates through I2C protocols + +Required properties: + +- compatible - "string" - One of: + "ti,tlv320aic310x" - Generic TLV320AIC31xx with mono speaker amp + "ti,tlv320aic311x" - Generic TLV320AIC31xx with stereo speaker amp + "ti,tlv320aic3100" - TLV320AIC3100 (mono speaker amp, no MiniDSP) + "ti,tlv320aic3110" - TLV320AIC3110 (stereo speaker amp, no MiniDSP) + "ti,tlv320aic3120" - TLV320AIC3120 (mono speaker amp, MiniDSP) + "ti,tlv320aic3111" - TLV320AIC3111 (stereo speaker amp, MiniDSP) + +- reg - <int> - I2C slave address +- HPVDD-supply, SPRVDD-supply, SPLVDD-supply, AVDD-supply, IOVDD-supply, + DVDD-supply : power supplies for the device as covered in + Documentation/devicetree/bindings/regulator/regulator.txt + + +Optional properties: + +- gpio-reset - gpio pin number used for codec reset +- ai31xx-micbias-vg - MicBias Voltage setting + 1 or MICBIAS_2_0V - MICBIAS output is powered to 2.0V + 2 or MICBIAS_2_5V - MICBIAS output is powered to 2.5V + 3 or MICBIAS_AVDD - MICBIAS output is connected to AVDD + If this node is not mentioned or if the value is unknown, then + micbias is set to 2.0V. + +CODEC output pins: + * HPL + * HPR + * SPL, devices with stereo speaker amp + * SPR, devices with stereo speaker amp + * SPK, devices with mono speaker amp + * MICBIAS + +CODEC input pins: + * MIC1LP + * MIC1RP + * MIC1LM + +The pins can be used in referring sound node's audio-routing property. + +Example: +#include <dt-bindings/sound/tlv320aic31xx-micbias.h> + +tlv320aic31xx: tlv320aic31xx@18 { + compatible = "ti,tlv320aic311x"; + reg = <0x18>; + + ai31xx-micbias-vg = <MICBIAS_OFF>; + + HPVDD-supply = <®ulator>; + SPRVDD-supply = <®ulator>; + SPLVDD-supply = <®ulator>; + AVDD-supply = <®ulator>; + IOVDD-supply = <®ulator>; + DVDD-supply = <®ulator>; +}; diff --git a/Documentation/devicetree/bindings/sound/tlv320aic32x4.txt b/Documentation/devicetree/bindings/sound/tlv320aic32x4.txt new file mode 100644 index 000000000000..5e2741af27be --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tlv320aic32x4.txt @@ -0,0 +1,30 @@ +Texas Instruments - tlv320aic32x4 Codec module + +The tlv320aic32x4 serial control bus communicates through I2C protocols + +Required properties: + - compatible: Should be "ti,tlv320aic32x4" + - reg: I2C slave address + - supply-*: Required supply regulators are: + "iov" - digital IO power supply + "ldoin" - LDO power supply + "dv" - Digital core power supply + "av" - Analog core power supply + If you supply ldoin, dv and av are optional. Otherwise they are required + See regulator/regulator.txt for more information about the detailed binding + format. + +Optional properties: + - reset-gpios: Reset-GPIO phandle with args as described in gpio/gpio.txt + - clocks/clock-names: Clock named 'mclk' for the master clock of the codec. + See clock/clock-bindings.txt for information about the detailed format. + + +Example: + +codec: tlv320aic32x4@18 { + compatible = "ti,tlv320aic32x4"; + reg = <0x18>; + clocks = <&clks 201>; + clock-names = "mclk"; +}; diff --git a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt index 9d8ea14db490..5e6040c2c2e9 100644 --- a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt +++ b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt @@ -6,7 +6,6 @@ Required properties: - compatible - "string" - One of: "ti,tlv320aic3x" - Generic TLV320AIC3x device - "ti,tlv320aic32x4" - TLV320AIC32x4 "ti,tlv320aic33" - TLV320AIC33 "ti,tlv320aic3007" - TLV320AIC3007 "ti,tlv320aic3106" - TLV320AIC3106 diff --git a/Documentation/devicetree/bindings/sound/widgets.txt b/Documentation/devicetree/bindings/sound/widgets.txt new file mode 100644 index 000000000000..b6de5ba3b2de --- /dev/null +++ b/Documentation/devicetree/bindings/sound/widgets.txt @@ -0,0 +1,20 @@ +Widgets: + +This mainly specifies audio off-codec DAPM widgets. + +Each entry is a pair of strings in DT: + + "template-wname", "user-supplied-wname" + +The "template-wname" being the template widget name and currently includes: +"Microphone", "Line", "Headphone" and "Speaker". + +The "user-supplied-wname" being the user specified widget name. + +For instance: + simple-audio-widgets = + "Microphone", "Microphone Jack", + "Line", "Line In Jack", + "Line", "Line Out Jack", + "Headphone", "Headphone Jack", + "Speaker", "Speaker External"; diff --git a/Documentation/devicetree/bindings/sound/wm8904.txt b/Documentation/devicetree/bindings/sound/wm8904.txt new file mode 100644 index 000000000000..e99f4097c83c --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8904.txt @@ -0,0 +1,33 @@ +WM8904 audio CODEC + +This device supports I2C only. + +Required properties: + - compatible: "wlf,wm8904" + - reg: the I2C address of the device. + - clock-names: "mclk" + - clocks: reference to + <Documentation/devicetree/bindings/clock/clock-bindings.txt> + +Pins on the device (for linking into audio routes): + + * IN1L + * IN1R + * IN2L + * IN2R + * IN3L + * IN3R + * HPOUTL + * HPOUTR + * LINEOUTL + * LINEOUTR + * MICBIAS + +Examples: + +codec: wm8904@1a { + compatible = "wlf,wm8904"; + reg = <0x1a>; + clocks = <&pck0>; + clock-names = "mclk"; +}; diff --git a/Documentation/devicetree/bindings/spi/efm32-spi.txt b/Documentation/devicetree/bindings/spi/efm32-spi.txt index a590ca51be75..750e29aff9bc 100644 --- a/Documentation/devicetree/bindings/spi/efm32-spi.txt +++ b/Documentation/devicetree/bindings/spi/efm32-spi.txt @@ -3,24 +3,31 @@ Required properties: - #address-cells: see spi-bus.txt - #size-cells: see spi-bus.txt -- compatible: should be "efm32,spi" +- compatible: should be "energymicro,efm32-spi" - reg: Offset and length of the register set for the controller - interrupts: pair specifying rx and tx irq - clocks: phandle to the spi clock - cs-gpios: see spi-bus.txt -- location: Value to write to the ROUTE register's LOCATION bitfield to configure the pinmux for the device, see datasheet for values. + +Recommended properties : +- energymicro,location: Value to write to the ROUTE register's LOCATION + bitfield to configure the pinmux for the device, see + datasheet for values. + If this property is not provided, keeping what is + already configured in the hardware, so its either the + reset default 0 or whatever the bootloader did. Example: spi1: spi@0x4000c400 { /* USART1 */ #address-cells = <1>; #size-cells = <0>; - compatible = "efm32,spi"; + compatible = "energymicro,efm32-spi"; reg = <0x4000c400 0x400>; interrupts = <15 16>; clocks = <&cmu 20>; cs-gpios = <&gpio 51 1>; // D3 - location = <1>; + energymicro,location = <1>; status = "ok"; ks8851@0 { diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt index 4256a6df9b79..aad527b357a0 100644 --- a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt @@ -7,6 +7,9 @@ Required properties: - interrupts : Should contain CSPI/eCSPI interrupt - fsl,spi-num-chipselects : Contains the number of the chipselect - cs-gpios : Specifies the gpio pins to be used for chipselects. +- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, + Documentation/devicetree/bindings/dma/dma.txt +- dma-names: DMA request names should include "tx" and "rx" if present. Example: @@ -19,4 +22,6 @@ ecspi@70010000 { fsl,spi-num-chipselects = <2>; cs-gpios = <&gpio3 24 0>, /* GPIO3_24 */ <&gpio3 25 0>; /* GPIO3_25 */ + dmas = <&sdma 3 7 1>, <&sdma 4 7 2>; + dma-names = "rx", "tx"; }; diff --git a/Documentation/devicetree/bindings/spi/fsl-spi.txt b/Documentation/devicetree/bindings/spi/fsl-spi.txt index b032dd76e9d2..a2331372068c 100644 --- a/Documentation/devicetree/bindings/spi/fsl-spi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-spi.txt @@ -42,6 +42,10 @@ Required properties: - interrupts : should contain eSPI interrupt, the device has one interrupt. - fsl,espi-num-chipselects : the number of the chipselect signals. +Optional properties: +- fsl,csbef: chip select assertion time in bits before frame starts +- fsl,csaft: chip select negation time in bits after frame ends + Example: spi@110000 { #address-cells = <1>; @@ -51,4 +55,6 @@ Example: interrupts = <53 0x2>; interrupt-parent = <&mpic>; fsl,espi-num-chipselects = <4>; + fsl,csbef = <1>; + fsl,csaft = <1>; }; diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt b/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt new file mode 100644 index 000000000000..e2c88df2cc15 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt @@ -0,0 +1,95 @@ +Qualcomm Universal Peripheral (QUP) Serial Peripheral Interface (SPI) + +The QUP core is an AHB slave that provides a common data path (an output FIFO +and an input FIFO) for serial peripheral interface (SPI) mini-core. + +SPI in master mode supports up to 50MHz, up to four chip selects, programmable +data path from 4 bits to 32 bits and numerous protocol variants. + +Required properties: +- compatible: Should contain: + "qcom,spi-qup-v1.1.1" for 8660, 8960 and 8064. + "qcom,spi-qup-v2.1.1" for 8974 and later + "qcom,spi-qup-v2.2.1" for 8974 v2 and later. + +- reg: Should contain base register location and length +- interrupts: Interrupt number used by this controller + +- clocks: Should contain the core clock and the AHB clock. +- clock-names: Should be "core" for the core clock and "iface" for the + AHB clock. + +- #address-cells: Number of cells required to define a chip select + address on the SPI bus. Should be set to 1. +- #size-cells: Should be zero. + +Optional properties: +- spi-max-frequency: Specifies maximum SPI clock frequency, + Units - Hz. Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt +- num-cs: total number of chipselects +- cs-gpios: should specify GPIOs used for chipselects. + The gpios will be referred to as reg = <index> in the SPI child + nodes. If unspecified, a single SPI device without a chip + select can be used. + + +SPI slave nodes must be children of the SPI master node and can contain +properties described in Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + + spi_8: spi@f9964000 { /* BLSP2 QUP2 */ + + compatible = "qcom,spi-qup-v2"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xf9964000 0x1000>; + interrupts = <0 102 0>; + spi-max-frequency = <19200000>; + + clocks = <&gcc GCC_BLSP2_QUP2_SPI_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; + clock-names = "core", "iface"; + + pinctrl-names = "default"; + pinctrl-0 = <&spi8_default>; + + device@0 { + compatible = "arm,pl022-dummy"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <19200000>; + spi-cpol; + }; + + device@1 { + compatible = "arm,pl022-dummy"; + #address-cells = <1>; + #size-cells = <1>; + reg = <1>; /* Chip select 1 */ + spi-max-frequency = <9600000>; + spi-cpha; + }; + + device@2 { + compatible = "arm,pl022-dummy"; + #address-cells = <1>; + #size-cells = <1>; + reg = <2>; /* Chip select 2 */ + spi-max-frequency = <19200000>; + spi-cpol; + spi-cpha; + }; + + device@3 { + compatible = "arm,pl022-dummy"; + #address-cells = <1>; + #size-cells = <1>; + reg = <3>; /* Chip select 3 */ + spi-max-frequency = <19200000>; + spi-cpol; + spi-cpha; + spi-cs-high; + }; + }; diff --git a/Documentation/devicetree/bindings/spi/sh-hspi.txt b/Documentation/devicetree/bindings/spi/sh-hspi.txt index 30b57b1c8a13..319bad4af875 100644 --- a/Documentation/devicetree/bindings/spi/sh-hspi.txt +++ b/Documentation/devicetree/bindings/spi/sh-hspi.txt @@ -1,7 +1,29 @@ Renesas HSPI. Required properties: -- compatible : "renesas,hspi" -- reg : Offset and length of the register set for the device -- interrupts : interrupt line used by HSPI +- compatible : "renesas,hspi-<soctype>", "renesas,hspi" as fallback. + Examples with soctypes are: + - "renesas,hspi-r8a7778" (R-Car M1) + - "renesas,hspi-r8a7779" (R-Car H1) +- reg : Offset and length of the register set for the device +- interrupt-parent : The phandle for the interrupt controller that + services interrupts for this device +- interrupts : Interrupt specifier +- #address-cells : Must be <1> +- #size-cells : Must be <0> + +Pinctrl properties might be needed, too. See +Documentation/devicetree/bindings/pinctrl/renesas,*. + +Example: + + hspi0: spi@fffc7000 { + compatible = "renesas,hspi-r8a7778", "renesas,hspi"; + reg = <0xfffc7000 0x18>; + interrupt-parent = <&gic>; + interrupts = <0 63 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index e6222106ca36..d11c3721e7cd 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -1,12 +1,55 @@ Renesas MSIOF spi controller Required properties: -- compatible : "renesas,sh-msiof" for SuperH or - "renesas,sh-mobile-msiof" for SH Mobile series -- reg : Offset and length of the register set for the device -- interrupts : interrupt line used by MSIOF +- compatible : "renesas,msiof-<soctype>" for SoCs, + "renesas,sh-msiof" for SuperH, or + "renesas,sh-mobile-msiof" for SH Mobile series. + Examples with soctypes are: + "renesas,msiof-r8a7790" (R-Car H2) + "renesas,msiof-r8a7791" (R-Car M2-W) + "renesas,msiof-r8a7792" (R-Car V2H) + "renesas,msiof-r8a7793" (R-Car M2-N) + "renesas,msiof-r8a7794" (R-Car E2) +- reg : A list of offsets and lengths of the register sets for + the device. + If only one register set is present, it is to be used + by both the CPU and the DMA engine. + If two register sets are present, the first is to be + used by the CPU, and the second is to be used by the + DMA engine. +- interrupt-parent : The phandle for the interrupt controller that + services interrupts for this device +- interrupts : Interrupt specifier +- #address-cells : Must be <1> +- #size-cells : Must be <0> Optional properties: -- num-cs : total number of chip-selects -- renesas,tx-fifo-size : Overrides the default tx fifo size given in words -- renesas,rx-fifo-size : Overrides the default rx fifo size given in words +- clocks : Must contain a reference to the functional clock. +- num-cs : Total number of chip-selects (default is 1) +- dmas : Must contain a list of two references to DMA + specifiers, one for transmission, and one for + reception. +- dma-names : Must contain a list of two DMA names, "tx" and "rx". + +Optional properties, deprecated for soctype-specific bindings: +- renesas,tx-fifo-size : Overrides the default tx fifo size given in words + (default is 64) +- renesas,rx-fifo-size : Overrides the default rx fifo size given in words + (default is 64, or 256 on R-Car Gen2) + +Pinctrl properties might be needed, too. See +Documentation/devicetree/bindings/pinctrl/renesas,*. + +Example: + + msiof0: spi@e6e20000 { + compatible = "renesas,msiof-r8a7791"; + reg = <0 0xe6e20000 0 0x0064>, <0 0xe7e20000 0 0x0064>; + interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp0_clks R8A7791_CLK_MSIOF0>; + dmas = <&dmac0 0x51>, <&dmac0 0x52>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt new file mode 100644 index 000000000000..bd99193e87b9 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt @@ -0,0 +1,28 @@ +Synopsys DesignWare AMBA 2.0 Synchronous Serial Interface. + +Required properties: +- compatible : "snps,dw-apb-ssi" +- reg : The register base for the controller. +- interrupts : One interrupt, used by the controller. +- #address-cells : <1>, as required by generic SPI binding. +- #size-cells : <0>, also as required by generic SPI binding. + +Optional properties: +- cs-gpios : Specifies the gpio pis to be used for chipselects. +- num-cs : The number of chipselects. If omitted, this will default to 4. + +Child nodes as per the generic SPI binding. + +Example: + + spi@fff00000 { + compatible = "snps,dw-apb-ssi"; + reg = <0xfff00000 0x1000>; + interrupts = <0 154 4>; + #address-cells = <1>; + #size-cells = <0>; + num-cs = <2>; + cs-gpios = <&gpio0 13 0>, + <&gpio0 14 0>; + }; + diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt index e5a4d1b4acfe..bbaa857dd68f 100644 --- a/Documentation/devicetree/bindings/spi/spi-bus.txt +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -55,13 +55,15 @@ contain the following properties. chip select active high - spi-3wire - (optional) Empty property indicating device requires 3-wire mode. +- spi-lsb-first - (optional) Empty property indicating device requires + LSB first mode. - spi-tx-bus-width - (optional) The bus width(number of data wires) that used for MOSI. Defaults to 1 if not present. - spi-rx-bus-width - (optional) The bus width(number of data wires) that used for MISO. Defaults to 1 if not present. Some SPI controllers and devices support Dual and Quad SPI transfer mode. -It allows data in SPI system transfered in 2 wires(DUAL) or 4 wires(QUAD). +It allows data in the SPI system to be transferred in 2 wires(DUAL) or 4 wires(QUAD). Now the value that spi-tx-bus-width and spi-rx-bus-width can receive is only 1(SINGLE), 2(DUAL) and 4(QUAD). Dual/Quad mode is not allowed when 3-wire mode is used. diff --git a/Documentation/devicetree/bindings/spi/spi-cadence.txt b/Documentation/devicetree/bindings/spi/spi-cadence.txt new file mode 100644 index 000000000000..94f09141a4f0 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-cadence.txt @@ -0,0 +1,31 @@ +Cadence SPI controller Device Tree Bindings +------------------------------------------- + +Required properties: +- compatible : Should be "cdns,spi-r1p6" or "xlnx,zynq-spi-r1p6". +- reg : Physical base address and size of SPI registers map. +- interrupts : Property with a value describing the interrupt + number. +- interrupt-parent : Must be core interrupt controller +- clock-names : List of input clock names - "ref_clk", "pclk" + (See clock bindings for details). +- clocks : Clock phandles (see clock bindings for details). + +Optional properties: +- num-cs : Number of chip selects used. + If a decoder is used, this will be the number of + chip selects after the decoder. +- is-decoded-cs : Flag to indicate whether decoder is used or not. + +Example: + + spi@e0007000 { + compatible = "xlnx,zynq-spi-r1p6"; + clock-names = "ref_clk", "pclk"; + clocks = <&clkc 26>, <&clkc 35>; + interrupt-parent = <&intc>; + interrupts = <0 49 4>; + num-cs = <4>; + is-decoded-cs = <0>; + reg = <0xe0007000 0x1000>; + } ; diff --git a/Documentation/devicetree/bindings/spi/spi-davinci.txt b/Documentation/devicetree/bindings/spi/spi-davinci.txt index 6d0ac8d0ad9b..12ecfe9e3599 100644 --- a/Documentation/devicetree/bindings/spi/spi-davinci.txt +++ b/Documentation/devicetree/bindings/spi/spi-davinci.txt @@ -1,5 +1,10 @@ Davinci SPI controller device bindings +Links on DM: +Keystone 2 - http://www.ti.com/lit/ug/sprugp2a/sprugp2a.pdf +dm644x - http://www.ti.com/lit/ug/sprue32a/sprue32a.pdf +OMAP-L138/da830 - http://www.ti.com/lit/ug/spruh77a/spruh77a.pdf + Required properties: - #address-cells: number of cells required to define a chip select address on the SPI bus. Should be set to 1. @@ -8,7 +13,8 @@ Required properties: - "ti,dm6441-spi" for SPI used similar to that on DM644x SoC family - "ti,da830-spi" for SPI used similar to that on DA8xx SoC family - reg: Offset and length of SPI controller register space -- num-cs: Number of chip selects +- num-cs: Number of chip selects. This includes internal as well as + GPIO chip selects. - ti,davinci-spi-intr-line: interrupt line used to connect the SPI IP to the interrupt controller within the SoC. Possible values are 0 and 1. Manual says one of the two possible interrupt @@ -17,6 +23,36 @@ Required properties: - interrupts: interrupt number mapped to CPU. - clocks: spi clk phandle +Optional: +- cs-gpios: gpio chip selects + For example to have 3 internal CS and 2 GPIO CS, user could define + cs-gpios = <0>, <0>, <0>, <&gpio1 30 0>, <&gpio1 31 0>; + where first three are internal CS and last two are GPIO CS. + +Optional properties for slave devices: +SPI slave nodes can contain the following properties. +Not all SPI Peripherals from Texas Instruments support this. +Please check SPI peripheral documentation for a device before using these. + +- ti,spi-wdelay : delay between transmission of words + (SPIFMTn.WDELAY, SPIDAT1.WDEL) must be specified in number of SPI module + clock periods. + + delay = WDELAY * SPI_module_clock_period + 2 * SPI_module_clock_period + +Below is timing diagram which shows functional meaning of +"ti,spi-wdelay" parameter. + + +-+ +-+ +-+ +-+ +-+ +-+ +-+ +-+ +SPI_CLK | | | | | | | | | | | | | | | | + +----------+ +-+ +-+ +-+ +-+ +---------------------------+ +-+ +-+ +- + +SPI_SOMI/SIMO+-----------------+ +----------- + +----------+ word1 +---------------------------+word2 + +-----------------+ +----------- + WDELAY + <--------------------------> + Example of a NOR flash slave device (n25q032) connected to DaVinci SPI controller device over the SPI bus. @@ -36,6 +72,7 @@ spi0:spi@20BF0000 { compatible = "st,m25p32"; spi-max-frequency = <25000000>; reg = <0>; + ti,spi-wdelay = <8>; partition@0 { label = "u-boot-spl"; diff --git a/Documentation/devicetree/bindings/spi/spi-dw.txt b/Documentation/devicetree/bindings/spi/spi-dw.txt new file mode 100644 index 000000000000..7b63ed601990 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-dw.txt @@ -0,0 +1,24 @@ +Synopsys DesignWare SPI master + +Required properties: +- compatible: should be "snps,designware-spi" +- #address-cells: see spi-bus.txt +- #size-cells: see spi-bus.txt +- reg: address and length of the spi master registers +- interrupts: should contain one interrupt +- clocks: spi clock phandle +- num-cs: see spi-bus.txt + +Optional properties: +- cs-gpios: see spi-bus.txt + +Example: + +spi: spi@4020a000 { + compatible = "snps,designware-spi"; + interrupts = <11 1>; + reg = <0x4020a000 0x1000>; + clocks = <&pclk>; + num-cs = <2>; + cs-gpios = <&banka 0 0>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt index a1fb3035a42b..cbbe16ed3874 100644 --- a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt @@ -10,6 +10,12 @@ Required properties: - pinctrl-names: must contain a "default" entry. - spi-num-chipselects : the number of the chipselect signals. - bus-num : the slave chip chipselect signal number. + +Optional property: +- big-endian: If present the dspi device's registers are implemented + in big endian mode, otherwise in native mode(same with CPU), for more + detail please see: Documentation/devicetree/bindings/regmap/regmap.txt. + Example: dspi0@4002c000 { @@ -24,6 +30,7 @@ dspi0@4002c000 { bus-num = <0>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_dspi0_1>; + big-endian; status = "okay"; sflash: at26df081a@0 { diff --git a/Documentation/devicetree/bindings/spi/spi-orion.txt b/Documentation/devicetree/bindings/spi/spi-orion.txt index a3ff50fc76fb..50c3a3de61c1 100644 --- a/Documentation/devicetree/bindings/spi/spi-orion.txt +++ b/Documentation/devicetree/bindings/spi/spi-orion.txt @@ -1,7 +1,7 @@ Marvell Orion SPI device Required properties: -- compatible : should be "marvell,orion-spi". +- compatible : should be "marvell,orion-spi" or "marvell,armada-370-spi". - reg : offset and length of the register set for the device - cell-index : Which of multiple SPI controllers is this. Optional properties: diff --git a/Documentation/devicetree/bindings/spi/spi-rockchip.txt b/Documentation/devicetree/bindings/spi/spi-rockchip.txt new file mode 100644 index 000000000000..467dec441c62 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-rockchip.txt @@ -0,0 +1,41 @@ +* Rockchip SPI Controller + +The Rockchip SPI controller is used to interface with various devices such as flash +and display controllers using the SPI communication interface. + +Required Properties: + +- compatible: should be one of the following. + "rockchip,rk3066-spi" for rk3066. + "rockchip,rk3188-spi", "rockchip,rk3066-spi" for rk3188. + "rockchip,rk3288-spi", "rockchip,rk3066-spi" for rk3288. +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: The interrupt number to the cpu. The interrupt specifier format + depends on the interrupt controller. +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Shall be "spiclk" for the transfer-clock, and "apb_pclk" for + the peripheral clock. +- #address-cells: should be 1. +- #size-cells: should be 0. + +Optional Properties: + +- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, + Documentation/devicetree/bindings/dma/dma.txt +- dma-names: DMA request names should include "tx" and "rx" if present. + + +Example: + + spi0: spi@ff110000 { + compatible = "rockchip,rk3066-spi"; + reg = <0xff110000 0x1000>; + dmas = <&pdma1 11>, <&pdma1 12>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>; + clock-names = "spiclk", "apb_pclk"; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-rspi.txt b/Documentation/devicetree/bindings/spi/spi-rspi.txt new file mode 100644 index 000000000000..8f4169f63936 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-rspi.txt @@ -0,0 +1,69 @@ +Device tree configuration for Renesas RSPI/QSPI driver + +Required properties: +- compatible : For Renesas Serial Peripheral Interface on legacy SH: + "renesas,rspi-<soctype>", "renesas,rspi" as fallback. + For Renesas Serial Peripheral Interface on RZ/A1H: + "renesas,rspi-<soctype>", "renesas,rspi-rz" as fallback. + For Quad Serial Peripheral Interface on R-Car Gen2: + "renesas,qspi-<soctype>", "renesas,qspi" as fallback. + Examples with soctypes are: + - "renesas,rspi-sh7757" (SH) + - "renesas,rspi-r7s72100" (RZ/A1H) + - "renesas,qspi-r8a7790" (R-Car H2) + - "renesas,qspi-r8a7791" (R-Car M2-W) + - "renesas,qspi-r8a7792" (R-Car V2H) + - "renesas,qspi-r8a7793" (R-Car M2-N) + - "renesas,qspi-r8a7794" (R-Car E2) +- reg : Address start and address range size of the device +- interrupts : A list of interrupt-specifiers, one for each entry in + interrupt-names. + If interrupt-names is not present, an interrupt specifier + for a single muxed interrupt. +- interrupt-names : A list of interrupt names. Should contain (if present): + - "error" for SPEI, + - "rx" for SPRI, + - "tx" to SPTI, + - "mux" for a single muxed interrupt. +- interrupt-parent : The phandle for the interrupt controller that + services interrupts for this device. +- num-cs : Number of chip selects. Some RSPI cores have more than 1. +- #address-cells : Must be <1> +- #size-cells : Must be <0> + +Optional properties: +- clocks : Must contain a reference to the functional clock. +- dmas : Must contain a list of two references to DMA specifiers, + one for transmission, and one for reception. +- dma-names : Must contain a list of two DMA names, "tx" and "rx". + +Pinctrl properties might be needed, too. See +Documentation/devicetree/bindings/pinctrl/renesas,*. + +Examples: + + spi0: spi@e800c800 { + compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz"; + reg = <0xe800c800 0x24>; + interrupts = <0 238 IRQ_TYPE_LEVEL_HIGH>, + <0 239 IRQ_TYPE_LEVEL_HIGH>, + <0 240 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", "rx", "tx"; + interrupt-parent = <&gic>; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + }; + + spi: spi@e6b10000 { + compatible = "renesas,qspi-r8a7791", "renesas,qspi"; + reg = <0 0xe6b10000 0 0x2c>; + interrupt-parent = <&gic>; + interrupts = <0 184 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7791_CLK_QSPI_MOD>; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&dmac0 0x17>, <&dmac0 0x18>; + dma-names = "tx", "rx"; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-samsung.txt b/Documentation/devicetree/bindings/spi/spi-samsung.txt index 86aa061f069f..1e8a8578148f 100644 --- a/Documentation/devicetree/bindings/spi/spi-samsung.txt +++ b/Documentation/devicetree/bindings/spi/spi-samsung.txt @@ -8,7 +8,6 @@ Required SoC Specific Properties: - compatible: should be one of the following. - samsung,s3c2443-spi: for s3c2443, s3c2416 and s3c2450 platforms - samsung,s3c6410-spi: for s3c6410 platforms - - samsung,s5p6440-spi: for s5p6440 and s5p6450 platforms - samsung,s5pv210-spi: for s5pv210 and s5pc110 platforms - samsung,exynos4210-spi: for exynos4 and exynos5 platforms @@ -18,14 +17,11 @@ Required SoC Specific Properties: - interrupts: The interrupt number to the cpu. The interrupt specifier format depends on the interrupt controller. -[PRELIMINARY: the dma channel allocation will change once there are -official DMA bindings] +- dmas : Two or more DMA channel specifiers following the convention outlined + in bindings/dma/dma.txt -- tx-dma-channel: The dma channel specifier for tx operations. The format of - the dma specifier depends on the dma controller. - -- rx-dma-channel: The dma channel specifier for rx operations. The format of - the dma specifier depends on the dma controller. +- dma-names: Names for the dma channels. There must be at least one channel + named "tx" for transmit and named "rx" for receive. Required Board Specific Properties: @@ -42,15 +38,13 @@ Optional Board Specific Properties: - num-cs: Specifies the number of chip select lines supported. If not specified, the default number of chip select lines is set to 1. +- cs-gpios: should specify GPIOs used for chipselects (see spi-bus.txt) + SPI Controller specific data in SPI slave nodes: - The spi slave nodes should provide the following information which is required by the spi controller. - - cs-gpio: A gpio specifier that specifies the gpio line used as - the slave select line by the spi controller. The format of the gpio - specifier depends on the gpio controller. - - samsung,spi-feedback-delay: The sampling phase shift to be applied on the miso line (to account for any lag in the miso line). The following are the valid values. @@ -74,8 +68,11 @@ Example: compatible = "samsung,exynos4210-spi"; reg = <0x12d20000 0x100>; interrupts = <0 66 0>; - tx-dma-channel = <&pdma0 5>; - rx-dma-channel = <&pdma0 4>; + dmas = <&pdma0 5 + &pdma0 4>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; }; - Board Specific Portion: @@ -85,6 +82,7 @@ Example: #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&spi0_bus>; + cs-gpios = <&gpa2 5 0>; w25q80bw@0 { #address-cells = <1>; @@ -94,7 +92,6 @@ Example: spi-max-frequency = <10000>; controller-data { - cs-gpio = <&gpa2 5 1 0 3>; samsung,spi-feedback-delay = <0>; }; diff --git a/Documentation/devicetree/bindings/spi/spi-sun4i.txt b/Documentation/devicetree/bindings/spi/spi-sun4i.txt new file mode 100644 index 000000000000..de827f5a301e --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-sun4i.txt @@ -0,0 +1,24 @@ +Allwinner A10 SPI controller + +Required properties: +- compatible: Should be "allwinner,sun4-a10-spi". +- reg: Should contain register location and length. +- interrupts: Should contain interrupt. +- clocks: phandle to the clocks feeding the SPI controller. Two are + needed: + - "ahb": the gated AHB parent clock + - "mod": the parent module clock +- clock-names: Must contain the clock names described just above + +Example: + +spi1: spi@01c06000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c06000 0x1000>; + interrupts = <11>; + clocks = <&ahb_gates 21>, <&spi1_clk>; + clock-names = "ahb", "mod"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-sun6i.txt b/Documentation/devicetree/bindings/spi/spi-sun6i.txt new file mode 100644 index 000000000000..21de73db6a05 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-sun6i.txt @@ -0,0 +1,24 @@ +Allwinner A31 SPI controller + +Required properties: +- compatible: Should be "allwinner,sun6i-a31-spi". +- reg: Should contain register location and length. +- interrupts: Should contain interrupt. +- clocks: phandle to the clocks feeding the SPI controller. Two are + needed: + - "ahb": the gated AHB parent clock + - "mod": the parent module clock +- clock-names: Must contain the clock names described just above +- resets: phandle to the reset controller asserting this device in + reset + +Example: + +spi1: spi@01c69000 { + compatible = "allwinner,sun6i-a31-spi"; + reg = <0x01c69000 0x1000>; + interrupts = <0 66 4>; + clocks = <&ahb1_gates 21>, <&spi1_clk>; + clock-names = "ahb", "mod"; + resets = <&ahb1_rst 21>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-xtensa-xtfpga.txt b/Documentation/devicetree/bindings/spi/spi-xtensa-xtfpga.txt new file mode 100644 index 000000000000..b6ebe2bc7041 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-xtensa-xtfpga.txt @@ -0,0 +1,9 @@ +Cadence Xtensa XTFPGA platform SPI controller. + +This simple SPI master controller is built into xtfpga bitstreams and is used +to control daughterboard audio codec. + +Required properties: +- compatible: should be "cdns,xtfpga-spi". +- reg: physical base address of the controller and length of memory mapped + region. diff --git a/Documentation/devicetree/bindings/spi/spi_atmel.txt b/Documentation/devicetree/bindings/spi/spi_atmel.txt index 07e04cdc0c9e..4f8184d069cb 100644 --- a/Documentation/devicetree/bindings/spi/spi_atmel.txt +++ b/Documentation/devicetree/bindings/spi/spi_atmel.txt @@ -5,6 +5,9 @@ Required properties: - reg: Address and length of the register set for the device - interrupts: Should contain spi interrupt - cs-gpios: chipselects +- clock-names: tuple listing input clock names. + Required elements: "spi_clk" +- clocks: phandles to input clocks. Example: @@ -14,6 +17,8 @@ spi1: spi@fffcc000 { interrupts = <13 4 5>; #address-cells = <1>; #size-cells = <0>; + clocks = <&spi1_clk>; + clock-names = "spi_clk"; cs-gpios = <&pioB 3 0>; status = "okay"; diff --git a/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt b/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt new file mode 100644 index 000000000000..715d0998af8e --- /dev/null +++ b/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt @@ -0,0 +1,61 @@ +Qualcomm SPMI Controller (PMIC Arbiter) + +The SPMI PMIC Arbiter is found on the Snapdragon 800 Series. It is an SPMI +controller with wrapping arbitration logic to allow for multiple on-chip +devices to control a single SPMI master. + +The PMIC Arbiter can also act as an interrupt controller, providing interrupts +to slave devices. + +See spmi.txt for the generic SPMI controller binding requirements for child +nodes. + +See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt for +generic interrupt controller binding documentation. + +Required properties: +- compatible : should be "qcom,spmi-pmic-arb". +- reg-names : must contain: + "core" - core registers + "intr" - interrupt controller registers + "cnfg" - configuration registers +- reg : address + size pairs describing the PMIC arb register sets; order must + correspond with the order of entries in reg-names +- #address-cells : must be set to 2 +- #size-cells : must be set to 0 +- qcom,ee : indicates the active Execution Environment identifier (0-5) +- qcom,channel : which of the PMIC Arb provided channels to use for accesses (0-5) +- interrupts : interrupt list for the PMIC Arb controller, must contain a + single interrupt entry for the peripheral interrupt +- interrupt-names : corresponding interrupt names for the interrupts + listed in the 'interrupts' property, must contain: + "periph_irq" - summary interrupt for PMIC peripherals +- interrupt-controller : boolean indicator that the PMIC arbiter is an interrupt controller +- #interrupt-cells : must be set to 4. Interrupts are specified as a 4-tuple: + cell 1: slave ID for the requested interrupt (0-15) + cell 2: peripheral ID for requested interrupt (0-255) + cell 3: the requested peripheral interrupt (0-7) + cell 4: interrupt flags indicating level-sense information, as defined in + dt-bindings/interrupt-controller/irq.h + +Example: + + spmi { + compatible = "qcom,spmi-pmic-arb"; + reg-names = "core", "intr", "cnfg"; + reg = <0xfc4cf000 0x1000>, + <0xfc4cb000 0x1000>, + <0xfc4ca000 0x1000>; + + interrupt-names = "periph_irq"; + interrupts = <0 190 0>; + + qcom,ee = <0>; + qcom,channel = <0>; + + #address-cells = <2>; + #size-cells = <0>; + + interrupt-controller; + #interrupt-cells = <4>; + }; diff --git a/Documentation/devicetree/bindings/spmi/spmi.txt b/Documentation/devicetree/bindings/spmi/spmi.txt new file mode 100644 index 000000000000..4bb10d161a27 --- /dev/null +++ b/Documentation/devicetree/bindings/spmi/spmi.txt @@ -0,0 +1,41 @@ +System Power Management Interface (SPMI) Controller + +This document defines a generic set of bindings for use by SPMI controllers. A +controller is modelled in device tree as a node with zero or more child nodes, +each representing a unique slave on the bus. + +Required properties: +- #address-cells : must be set to 2 +- #size-cells : must be set to 0 + +Child nodes: + +An SPMI controller node can contain zero or more child nodes representing slave +devices on the bus. Child 'reg' properties are specified as an address, type +pair. The address must be in the range 0-15 (4 bits). The type must be one of +SPMI_USID (0) or SPMI_GSID (1) for Unique Slave ID or Group Slave ID respectively. +These are the identifiers "statically assigned by the system integrator", as +per the SPMI spec. + +Each child node must have one and only one 'reg' entry of type SPMI_USID. + +#include <dt-bindings/spmi/spmi.h> + + spmi@.. { + compatible = "..."; + reg = <...>; + + #address-cells = <2>; + #size-cells = <0>; + + child@0 { + compatible = "..."; + reg = <0 SPMI_USID>; + }; + + child@7 { + compatible = "..."; + reg = <7 SPMI_USID + 3 SPMI_GSID>; + }; + }; diff --git a/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt b/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt index b876d4925a57..e75f0e549fff 100644 --- a/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt +++ b/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt @@ -1,3 +1,22 @@ +Freescale i.MX DRM master device +================================ + +The freescale i.MX DRM master device is a virtual device needed to list all +IPU or other display interface nodes that comprise the graphics subsystem. + +Required properties: +- compatible: Should be "fsl,imx-display-subsystem" +- ports: Should contain a list of phandles pointing to display interface ports + of IPU devices + +example: + +display-subsystem { + compatible = "fsl,display-subsystem"; + ports = <&ipu_di0>; +}; + + Freescale i.MX IPUv3 ==================== @@ -7,18 +26,31 @@ Required properties: datasheet - interrupts: Should contain sync interrupt and error interrupt, in this order. -- #crtc-cells: 1, See below - resets: phandle pointing to the system reset controller and reset line index, see reset/fsl,imx-src.txt for details +Optional properties: +- port@[0-3]: Port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + Ports 0 and 1 should correspond to CSI0 and CSI1, + ports 2 and 3 should correspond to DI0 and DI1, respectively. example: ipu: ipu@18000000 { - #crtc-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; compatible = "fsl,imx53-ipu"; reg = <0x18000000 0x080000000>; interrupts = <11 10>; resets = <&src 2>; + + ipu_di0: port@2 { + reg = <2>; + + ipu_di0_disp0: endpoint { + remote-endpoint = <&display_in>; + }; + }; }; Parallel display support @@ -26,19 +58,26 @@ Parallel display support Required properties: - compatible: Should be "fsl,imx-parallel-display" -- crtc: the crtc this display is connected to, see below Optional properties: - interface_pix_fmt: How this display is connected to the - crtc. Currently supported types: "rgb24", "rgb565", "bgr666" + display interface. Currently supported types: "rgb24", "rgb565", "bgr666" + and "lvds666". - edid: verbatim EDID data block describing attached display. - ddc: phandle describing the i2c bus handling the display data channel +- port: A port node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. example: display@di0 { compatible = "fsl,imx-parallel-display"; edid = [edid-data]; - crtc = <&ipu 0>; interface-pix-fmt = "rgb24"; + + port { + display_in: endpoint { + remote-endpoint = <&ipu_di0_disp0>; + }; + }; }; diff --git a/Documentation/devicetree/bindings/staging/imx-drm/hdmi.txt b/Documentation/devicetree/bindings/staging/imx-drm/hdmi.txt new file mode 100644 index 000000000000..1b756cf9afb0 --- /dev/null +++ b/Documentation/devicetree/bindings/staging/imx-drm/hdmi.txt @@ -0,0 +1,58 @@ +Device-Tree bindings for HDMI Transmitter + +HDMI Transmitter +================ + +The HDMI Transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP +with accompanying PHY IP. + +Required properties: + - #address-cells : should be <1> + - #size-cells : should be <0> + - compatible : should be "fsl,imx6q-hdmi" or "fsl,imx6dl-hdmi". + - gpr : should be <&gpr>. + The phandle points to the iomuxc-gpr region containing the HDMI + multiplexer control register. + - clocks, clock-names : phandles to the HDMI iahb and isrf clocks, as described + in Documentation/devicetree/bindings/clock/clock-bindings.txt and + Documentation/devicetree/bindings/clock/imx6q-clock.txt. + - port@[0-4]: Up to four port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt, + corresponding to the four inputs to the HDMI multiplexer. + +Optional properties: + - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing + +example: + + gpr: iomuxc-gpr@020e0000 { + /* ... */ + }; + + hdmi: hdmi@0120000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx6q-hdmi"; + reg = <0x00120000 0x9000>; + interrupts = <0 115 0x04>; + gpr = <&gpr>; + clocks = <&clks 123>, <&clks 124>; + clock-names = "iahb", "isfr"; + ddc-i2c-bus = <&i2c2>; + + port@0 { + reg = <0>; + + hdmi_mux_0: endpoint { + remote-endpoint = <&ipu1_di0_hdmi>; + }; + }; + + port@1 { + reg = <1>; + + hdmi_mux_1: endpoint { + remote-endpoint = <&ipu1_di1_hdmi>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/staging/imx-drm/ldb.txt b/Documentation/devicetree/bindings/staging/imx-drm/ldb.txt index ed9377811ee2..443bcb6134d5 100644 --- a/Documentation/devicetree/bindings/staging/imx-drm/ldb.txt +++ b/Documentation/devicetree/bindings/staging/imx-drm/ldb.txt @@ -50,12 +50,17 @@ have a look at Documentation/devicetree/bindings/video/display-timing.txt. Required properties: - reg : should be <0> or <1> - - crtcs : a list of phandles with index pointing to the IPU display interfaces - that can be used as video source for this channel. - fsl,data-mapping : should be "spwg" or "jeida" This describes how the color bits are laid out in the serialized LVDS signal. - fsl,data-width : should be <18> or <24> + - port: A port node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + On i.MX5, the internal two-input-multiplexer is used. + Due to hardware limitations, only one port (port@[0,1]) + can be used for each channel (lvds-channel@[0,1], respectively) + On i.MX6, there should be four ports (port@[0-3]) that correspond + to the four LVDS multiplexer inputs. example: @@ -76,24 +81,42 @@ ldb: ldb@53fa8008 { "di0", "di1"; lvds-channel@0 { + #address-cells = <1>; + #size-cells = <0>; reg = <0>; - crtcs = <&ipu 0>; fsl,data-mapping = "spwg"; fsl,data-width = <24>; display-timings { /* ... */ }; + + port@0 { + reg = <0>; + + lvds0_in: endpoint { + remote-endpoint = <&ipu_di0_lvds0>; + }; + }; }; lvds-channel@1 { + #address-cells = <1>; + #size-cells = <0>; reg = <1>; - crtcs = <&ipu 1>; fsl,data-mapping = "spwg"; fsl,data-width = <24>; display-timings { /* ... */ }; + + port@1 { + reg = <1>; + + lvds1_in: endpoint { + remote-endpoint = <&ipu_di1_lvds1>; + }; + }; }; }; diff --git a/Documentation/devicetree/bindings/submitting-patches.txt b/Documentation/devicetree/bindings/submitting-patches.txt index 042a0273b8ba..b7ba01ad1426 100644 --- a/Documentation/devicetree/bindings/submitting-patches.txt +++ b/Documentation/devicetree/bindings/submitting-patches.txt @@ -12,6 +12,9 @@ I. For patch submitters devicetree@vger.kernel.org + 3) The Documentation/ portion of the patch should come in the series before + the code implementing the binding. + II. For kernel maintainers 1) If you aren't comfortable reviewing a given binding, reply to it and ask diff --git a/Documentation/devicetree/bindings/thermal/armada-thermal.txt b/Documentation/devicetree/bindings/thermal/armada-thermal.txt index fff93d5f92de..4cf024929a3f 100644 --- a/Documentation/devicetree/bindings/thermal/armada-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/armada-thermal.txt @@ -1,11 +1,21 @@ -* Marvell Armada 370/XP thermal management +* Marvell Armada 370/375/380/XP thermal management Required properties: - compatible: Should be set to one of the following: marvell,armada370-thermal + marvell,armada375-thermal + marvell,armada375-z1-thermal + marvell,armada380-thermal marvell,armadaxp-thermal + Note: As the name suggests, "marvell,armada375-z1-thermal" + applies for the SoC Z1 stepping only. On such stepping + some quirks need to be done and the register offset differs + from the one in the A0 stepping. + The operating system may auto-detect the SoC stepping and + update the compatible and register offsets at runtime. + - reg: Device's register space. Two entries are expected, see the examples below. The first one is required for the sensor register; diff --git a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt index 284f5300fd8b..ae738f562acc 100644 --- a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt @@ -3,19 +3,39 @@ ** Required properties: - compatible : One of the following: + "samsung,exynos3250-tmu" "samsung,exynos4412-tmu" "samsung,exynos4210-tmu" "samsung,exynos5250-tmu" + "samsung,exynos5260-tmu" + "samsung,exynos5420-tmu" for TMU channel 0, 1 on Exynos5420 + "samsung,exynos5420-tmu-ext-triminfo" for TMU channels 2, 3 and 4 + Exynos5420 (Must pass triminfo base and triminfo clock) "samsung,exynos5440-tmu" - interrupt-parent : The phandle for the interrupt controller - reg : Address range of the thermal registers. For soc's which has multiple instances of TMU and some registers are shared across all TMU's like interrupt related then 2 set of register has to supplied. First set - belongs to each instance of TMU and second set belongs to common TMU - registers. + belongs to register set of TMU instance and second set belongs to + registers shared with the TMU instance. + + NOTE: On Exynos5420, the TRIMINFO register is misplaced for TMU + channels 2, 3 and 4 + Use "samsung,exynos5420-tmu-ext-triminfo" in cases, there is a misplaced + register, also provide clock to access that base. + + TRIMINFO at 0x1006c000 contains data for TMU channel 3 + TRIMINFO at 0x100a0000 contains data for TMU channel 4 + TRIMINFO at 0x10068000 contains data for TMU channel 2 + - interrupts : Should contain interrupt for thermal system -- clocks : The main clock for TMU device +- clocks : The main clocks for TMU device + -- 1. operational clock for TMU channel + -- 2. optional clock to access the shared registers of TMU channel - clock-names : Thermal system clock name + -- "tmu_apbif" operational clock for current TMU channel + -- "tmu_triminfo_apbif" clock to access the shared triminfo register + for current TMU channel - vtmu-supply: This entry is optional and provides the regulator node supplying voltage to TMU. If needed this entry can be placed inside board/platform specific dts file. @@ -43,6 +63,31 @@ Example 2): clock-names = "tmu_apbif"; }; +Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register") + tmu_cpu2: tmu@10068000 { + compatible = "samsung,exynos5420-tmu-ext-triminfo"; + reg = <0x10068000 0x100>, <0x1006c000 0x4>; + interrupts = <0 184 0>; + clocks = <&clock 318>, <&clock 318>; + clock-names = "tmu_apbif", "tmu_triminfo_apbif"; + }; + + tmu_cpu3: tmu@1006c000 { + compatible = "samsung,exynos5420-tmu-ext-triminfo"; + reg = <0x1006c000 0x100>, <0x100a0000 0x4>; + interrupts = <0 185 0>; + clocks = <&clock 318>, <&clock 319>; + clock-names = "tmu_apbif", "tmu_triminfo_apbif"; + }; + + tmu_gpu: tmu@100a0000 { + compatible = "samsung,exynos5420-tmu-ext-triminfo"; + reg = <0x100a0000 0x100>, <0x10068000 0x4>; + interrupts = <0 215 0>; + clocks = <&clock 319>, <&clock 318>; + clock-names = "tmu_apbif", "tmu_triminfo_apbif"; + }; + Note: For multi-instance tmu each instance should have an alias correctly numbered in "aliases" node. diff --git a/Documentation/devicetree/bindings/thermal/imx-thermal.txt b/Documentation/devicetree/bindings/thermal/imx-thermal.txt index 1f0f67234a91..3c67bd50aa10 100644 --- a/Documentation/devicetree/bindings/thermal/imx-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/imx-thermal.txt @@ -1,7 +1,10 @@ * Temperature Monitor (TEMPMON) on Freescale i.MX SoCs Required properties: -- compatible : "fsl,imx6q-thermal" +- compatible : "fsl,imx6q-tempmon" for i.MX6Q, "fsl,imx6sx-tempmon" for i.MX6SX. + i.MX6SX has two more IRQs than i.MX6Q, one is IRQ_LOW and the other is IRQ_PANIC, + when temperature is below than low threshold, IRQ_LOW will be triggered, when temperature + is higher than panic threshold, system will auto reboot by SRC module. - fsl,tempmon : phandle pointer to system controller that contains TEMPMON control registers, e.g. ANATOP on imx6q. - fsl,tempmon-data : phandle pointer to fuse controller that contains TEMPMON diff --git a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt index 28ef498a66e5..43404b197933 100644 --- a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt @@ -1,7 +1,16 @@ * Renesas R-Car Thermal Required properties: -- compatible : "renesas,rcar-thermal" +- compatible : "renesas,thermal-<soctype>", "renesas,rcar-thermal" + as fallback. + Examples with soctypes are: + - "renesas,thermal-r8a73a4" (R-Mobile AP6) + - "renesas,thermal-r8a7779" (R-Car H1) + - "renesas,thermal-r8a7790" (R-Car H2) + - "renesas,thermal-r8a7791" (R-Car M2-W) + - "renesas,thermal-r8a7792" (R-Car V2H) + - "renesas,thermal-r8a7793" (R-Car M2-N) + - "renesas,thermal-r8a7794" (R-Car E2) - reg : Address range of the thermal registers. The 1st reg will be recognized as common register if it has "interrupts". @@ -12,18 +21,18 @@ Option properties: Example (non interrupt support): -thermal@e61f0100 { - compatible = "renesas,rcar-thermal"; - reg = <0xe61f0100 0x38>; +thermal@ffc48000 { + compatible = "renesas,thermal-r8a7779", "renesas,rcar-thermal"; + reg = <0xffc48000 0x38>; }; Example (interrupt support): thermal@e61f0000 { - compatible = "renesas,rcar-thermal"; + compatible = "renesas,thermal-r8a73a4", "renesas,rcar-thermal"; reg = <0xe61f0000 0x14 0xe61f0100 0x38 0xe61f0200 0x38 0xe61f0300 0x38>; - interrupts = <0 69 4>; + interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>; }; diff --git a/Documentation/devicetree/bindings/thermal/st-thermal.txt b/Documentation/devicetree/bindings/thermal/st-thermal.txt new file mode 100644 index 000000000000..3b9251b4a145 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/st-thermal.txt @@ -0,0 +1,42 @@ +Binding for Thermal Sensor driver for STMicroelectronics STi series of SoCs. + +Required parameters: +------------------- + +compatible : st,<SoC>-<module>-thermal; should be one of: + "st,stih415-sas-thermal", + "st,stih415-mpe-thermal", + "st,stih416-sas-thermal" + "st,stih416-mpe-thermal" + "st,stid127-thermal" or + "st,stih407-thermal" + according to the SoC type (stih415, stih416, stid127, stih407) + and module type (sas or mpe). On stid127 & stih407 there is only + one die/module, so there is no module type in the compatible + string. +clock-names : Should be "thermal". + See: Documentation/devicetree/bindings/resource-names.txt +clocks : Phandle of the clock used by the thermal sensor. + See: Documentation/devicetree/bindings/clock/clock-bindings.txt + +Optional parameters: +------------------- + +reg : For non-sysconf based sensors, this should be the physical base + address and length of the sensor's registers. +interrupts : Standard way to define interrupt number. + Interrupt is mandatory to be defined when compatible is + "stih416-mpe-thermal". + NB: For thermal sensor's for which no interrupt has been + defined, a polling delay of 1000ms will be used to read the + temperature from device. + +Example: + + temp1@fdfe8000 { + compatible = "st,stih416-mpe-thermal"; + reg = <0xfdfe8000 0x10>; + clock-names = "thermal"; + clocks = <&clk_m_mpethsens>; + interrupts = <GIC_SPI 23 IRQ_TYPE_NONE>; + }; diff --git a/Documentation/devicetree/bindings/timer/allwinner,sun4i-timer.txt b/Documentation/devicetree/bindings/timer/allwinner,sun4i-timer.txt index 48aeb7884ed3..5c2e23574ca0 100644 --- a/Documentation/devicetree/bindings/timer/allwinner,sun4i-timer.txt +++ b/Documentation/devicetree/bindings/timer/allwinner,sun4i-timer.txt @@ -2,7 +2,7 @@ Allwinner A1X SoCs Timer Controller Required properties: -- compatible : should be "allwinner,sun4i-timer" +- compatible : should be "allwinner,sun4i-a10-timer" - reg : Specifies base physical address and size of the registers. - interrupts : The interrupt of the first timer - clocks: phandle to the source clock (usually a 24 MHz fixed clock) @@ -10,7 +10,7 @@ Required properties: Example: timer { - compatible = "allwinner,sun4i-timer"; + compatible = "allwinner,sun4i-a10-timer"; reg = <0x01c20c00 0x400>; interrupts = <22>; clocks = <&osc>; diff --git a/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt b/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt index 7c26154b8bbb..27cfc7d7ccd7 100644 --- a/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt +++ b/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt @@ -9,6 +9,9 @@ Required properties: one) - clocks: phandle to the source clock (usually the AHB clock) +Optionnal properties: +- resets: phandle to a reset controller asserting the timer + Example: timer@01c60000 { @@ -19,4 +22,5 @@ timer@01c60000 { <0 53 1>, <0 54 1>; clocks = <&ahb1_gates 19>; + resets = <&ahb1rst 19>; }; diff --git a/Documentation/devicetree/bindings/timer/amlogic,meson6-timer.txt b/Documentation/devicetree/bindings/timer/amlogic,meson6-timer.txt new file mode 100644 index 000000000000..a092053f7902 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/amlogic,meson6-timer.txt @@ -0,0 +1,15 @@ +Amlogic Meson6 SoCs Timer Controller + +Required properties: + +- compatible : should be "amlogic,meson6-timer" +- reg : Specifies base physical address and size of the registers. +- interrupts : The interrupt of the first timer + +Example: + +timer@c1109940 { + compatible = "amlogic,meson6-timer"; + reg = <0xc1109940 0x14>; + interrupts = <0 10 1>; +}; diff --git a/Documentation/devicetree/bindings/timer/cirrus,clps711x-timer.txt b/Documentation/devicetree/bindings/timer/cirrus,clps711x-timer.txt new file mode 100644 index 000000000000..cd55b52548e4 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/cirrus,clps711x-timer.txt @@ -0,0 +1,29 @@ +* Cirrus Logic CLPS711X Timer Counter + +Required properties: +- compatible: Shall contain "cirrus,clps711x-timer". +- reg : Address and length of the register set. +- interrupts: The interrupt number of the timer. +- clocks : phandle of timer reference clock. + +Note: Each timer should have an alias correctly numbered in "aliases" node. + +Example: + aliases { + timer0 = &timer1; + timer1 = &timer2; + }; + + timer1: timer@80000300 { + compatible = "cirrus,ep7312-timer", "cirrus,clps711x-timer"; + reg = <0x80000300 0x4>; + interrupts = <8>; + clocks = <&clks 5>; + }; + + timer2: timer@80000340 { + compatible = "cirrus,ep7312-timer", "cirrus,clps711x-timer"; + reg = <0x80000340 0x4>; + interrupts = <9>; + clocks = <&clks 6>; + }; diff --git a/Documentation/devicetree/bindings/timer/efm32,timer.txt b/Documentation/devicetree/bindings/timer/energymicro,efm32-timer.txt index 97a568f696c9..e502c11b2211 100644 --- a/Documentation/devicetree/bindings/timer/efm32,timer.txt +++ b/Documentation/devicetree/bindings/timer/energymicro,efm32-timer.txt @@ -6,7 +6,7 @@ channels and can be used as PWM or Quadrature Decoder. Available clock sources are the cpu's HFPERCLK (with a 10-bit prescaler) or an external pin. Required properties: -- compatible : Should be efm32,timer +- compatible : Should be "energymicro,efm32-timer" - reg : Address and length of the register set - clocks : Should contain a reference to the HFPERCLK @@ -16,7 +16,7 @@ Optional properties: Example: timer@40010c00 { - compatible = "efm32,timer"; + compatible = "energymicro,efm32-timer"; reg = <0x40010c00 0x400>; interrupts = <14>; clocks = <&cmu clk_HFPERCLKTIMER3>; diff --git a/Documentation/devicetree/bindings/timer/fsl,ftm-timer.txt b/Documentation/devicetree/bindings/timer/fsl,ftm-timer.txt new file mode 100644 index 000000000000..aa8c40230e5e --- /dev/null +++ b/Documentation/devicetree/bindings/timer/fsl,ftm-timer.txt @@ -0,0 +1,31 @@ +Freescale FlexTimer Module (FTM) Timer + +Required properties: + +- compatible : should be "fsl,ftm-timer" +- reg : Specifies base physical address and size of the register sets for the + clock event device and clock source device. +- interrupts : Should be the clock event device interrupt. +- clocks : The clocks provided by the SoC to drive the timer, must contain an + entry for each entry in clock-names. +- clock-names : Must include the following entries: + o "ftm-evt" + o "ftm-src" + o "ftm-evt-counter-en" + o "ftm-src-counter-en" +- big-endian: One boolean property, the big endian mode will be in use if it is + present, or the little endian mode will be in use for all the device registers. + +Example: +ftm: ftm@400b8000 { + compatible = "fsl,ftm-timer"; + reg = <0x400b8000 0x1000 0x400b9000 0x1000>; + interrupts = <0 44 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "ftm-evt", "ftm-src", + "ftm-evt-counter-en", "ftm-src-counter-en"; + clocks = <&clks VF610_CLK_FTM2>, + <&clks VF610_CLK_FTM3>, + <&clks VF610_CLK_FTM2_EXT_FIX_EN>, + <&clks VF610_CLK_FTM3_EXT_FIX_EN>; + big-endian; +}; diff --git a/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt b/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt new file mode 100644 index 000000000000..7c4408ff4b83 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt @@ -0,0 +1,17 @@ +Mediatek MT6577, MT6572 and MT6589 Timers +--------------------------------------- + +Required properties: +- compatible: Should be "mediatek,mt6577-timer" +- reg: Should contain location and length for timers register. +- clocks: Clocks driving the timer hardware. This list should include two + clocks. The order is system clock and as second clock the RTC clock. + +Examples: + + timer@10008000 { + compatible = "mediatek,mt6577-timer"; + reg = <0x10008000 0x80>; + interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_LOW>; + clocks = <&system_clk>, <&rtc_clk>; + }; diff --git a/Documentation/devicetree/bindings/timer/renesas,cmt.txt b/Documentation/devicetree/bindings/timer/renesas,cmt.txt new file mode 100644 index 000000000000..1a05c1b243c1 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/renesas,cmt.txt @@ -0,0 +1,79 @@ +* Renesas R-Car Compare Match Timer (CMT) + +The CMT is a multi-channel 16/32/48-bit timer/counter with configurable clock +inputs and programmable compare match. + +Channels share hardware resources but their counter and compare match value +are independent. A particular CMT instance can implement only a subset of the +channels supported by the CMT model. Channel indices represent the hardware +position of the channel in the CMT and don't match the channel numbers in the +datasheets. + +Required Properties: + + - compatible: must contain one or more of the following: + - "renesas,cmt-32-r8a7740" for the r8a7740 32-bit CMT + (CMT0) + - "renesas,cmt-32-sh7372" for the sh7372 32-bit CMT + (CMT0) + - "renesas,cmt-32-sh73a0" for the sh73a0 32-bit CMT + (CMT0) + - "renesas,cmt-32" for all 32-bit CMT without fast clock support + (CMT0 on sh7372, sh73a0 and r8a7740) + This is a fallback for the above renesas,cmt-32-* entries. + + - "renesas,cmt-32-fast-r8a7740" for the r8a7740 32-bit CMT with fast + clock support (CMT[234]) + - "renesas,cmt-32-fast-sh7372" for the sh7372 32-bit CMT with fast + clock support (CMT[234]) + - "renesas,cmt-32-fast-sh73a0" for the sh73A0 32-bit CMT with fast + clock support (CMT[234]) + - "renesas,cmt-32-fast" for all 32-bit CMT with fast clock support + (CMT[234] on sh7372, sh73a0 and r8a7740) + This is a fallback for the above renesas,cmt-32-fast-* entries. + + - "renesas,cmt-48-sh7372" for the sh7372 48-bit CMT + (CMT1) + - "renesas,cmt-48-sh73a0" for the sh73A0 48-bit CMT + (CMT1) + - "renesas,cmt-48-r8a7740" for the r8a7740 48-bit CMT + (CMT1) + - "renesas,cmt-48" for all non-second generation 48-bit CMT + (CMT1 on sh7372, sh73a0 and r8a7740) + This is a fallback for the above renesas,cmt-48-* entries. + + - "renesas,cmt-48-r8a73a4" for the r8a73a4 48-bit CMT + (CMT[01]) + - "renesas,cmt-48-r8a7790" for the r8a7790 48-bit CMT + (CMT[01]) + - "renesas,cmt-48-r8a7791" for the r8a7791 48-bit CMT + (CMT[01]) + - "renesas,cmt-48-gen2" for all second generation 48-bit CMT + (CMT[01] on r8a73a4, r8a7790 and r8a7791) + This is a fallback for the renesas,cmt-48-r8a73a4, + renesas,cmt-48-r8a7790 and renesas,cmt-48-r8a7791 entries. + + - reg: base address and length of the registers block for the timer module. + - interrupts: interrupt-specifier for the timer, one per channel. + - clocks: a list of phandle + clock-specifier pairs, one for each entry + in clock-names. + - clock-names: must contain "fck" for the functional clock. + + - renesas,channels-mask: bitmask of the available channels. + + +Example: R8A7790 (R-Car H2) CMT0 node + + CMT0 on R8A7790 implements hardware channels 5 and 6 only and names + them channels 0 and 1 in the documentation. + + cmt0: timer@ffca0000 { + compatible = "renesas,cmt-48-r8a7790", "renesas,cmt-48-gen2"; + reg = <0 0xffca0000 0 0x1004>; + interrupts = <0 142 IRQ_TYPE_LEVEL_HIGH>, + <0 142 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp1_clks R8A7790_CLK_CMT0>; + clock-names = "fck"; + + renesas,channels-mask = <0x60>; + }; diff --git a/Documentation/devicetree/bindings/timer/renesas,mtu2.txt b/Documentation/devicetree/bindings/timer/renesas,mtu2.txt new file mode 100644 index 000000000000..ba0a34d97eb8 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/renesas,mtu2.txt @@ -0,0 +1,42 @@ +* Renesas Multi-Function Timer Pulse Unit 2 (MTU2) + +The MTU2 is a multi-purpose, multi-channel timer/counter with configurable +clock inputs and programmable compare match. + +Channels share hardware resources but their counter and compare match value +are independent. The MTU2 hardware supports five channels indexed from 0 to 4. + +Required Properties: + + - compatible: must be one or more of the following: + - "renesas,mtu2-r7s72100" for the r7s72100 MTU2 + - "renesas,mtu2" for any MTU2 + This is a fallback for the above renesas,mtu2-* entries + + - reg: base address and length of the registers block for the timer module. + + - interrupts: interrupt specifiers for the timer, one for each entry in + interrupt-names. + - interrupt-names: must contain one entry named "tgi?a" for each enabled + channel, where "?" is the channel index expressed as one digit from "0" to + "4". + + - clocks: a list of phandle + clock-specifier pairs, one for each entry + in clock-names. + - clock-names: must contain "fck" for the functional clock. + + +Example: R7S72100 (RZ/A1H) MTU2 node + + mtu2: timer@fcff0000 { + compatible = "renesas,mtu2-r7s72100", "renesas,mtu2"; + reg = <0xfcff0000 0x400>; + interrupts = <0 139 IRQ_TYPE_LEVEL_HIGH>, + <0 146 IRQ_TYPE_LEVEL_HIGH>, + <0 150 IRQ_TYPE_LEVEL_HIGH>, + <0 154 IRQ_TYPE_LEVEL_HIGH>, + <0 159 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "tgi0a", "tgi1a", "tgi2a", "tgi3a", "tgi4a"; + clocks = <&mstp3_clks R7S72100_CLK_MTU2>; + clock-names = "fck"; + }; diff --git a/Documentation/devicetree/bindings/timer/renesas,tmu.txt b/Documentation/devicetree/bindings/timer/renesas,tmu.txt new file mode 100644 index 000000000000..cd5f20bf2582 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/renesas,tmu.txt @@ -0,0 +1,44 @@ +* Renesas R-Mobile/R-Car Timer Unit (TMU) + +The TMU is a 32-bit timer/counter with configurable clock inputs and +programmable compare match. + +Channels share hardware resources but their counter and compare match value +are independent. The TMU hardware supports up to three channels. + +Required Properties: + + - compatible: must contain one or more of the following: + - "renesas,tmu-r8a7740" for the r8a7740 TMU + - "renesas,tmu-r8a7778" for the r8a7778 TMU + - "renesas,tmu-r8a7779" for the r8a7779 TMU + - "renesas,tmu" for any TMU. + This is a fallback for the above renesas,tmu-* entries + + - reg: base address and length of the registers block for the timer module. + + - interrupts: interrupt-specifier for the timer, one per channel. + + - clocks: a list of phandle + clock-specifier pairs, one for each entry + in clock-names. + - clock-names: must contain "fck" for the functional clock. + +Optional Properties: + + - #renesas,channels: number of channels implemented by the timer, must be 2 + or 3 (if not specified the value defaults to 3). + + +Example: R8A7779 (R-Car H1) TMU0 node + + tmu0: timer@ffd80000 { + compatible = "renesas,tmu-r8a7779", "renesas,tmu"; + reg = <0xffd80000 0x30>; + interrupts = <0 32 IRQ_TYPE_LEVEL_HIGH>, + <0 33 IRQ_TYPE_LEVEL_HIGH>, + <0 34 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp0_clks R8A7779_CLK_TMU0>; + clock-names = "fck"; + + #renesas,channels = <3>; + }; diff --git a/Documentation/devicetree/bindings/timer/ti,keystone-timer.txt b/Documentation/devicetree/bindings/timer/ti,keystone-timer.txt new file mode 100644 index 000000000000..5fbe361252b4 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/ti,keystone-timer.txt @@ -0,0 +1,29 @@ +* Device tree bindings for Texas instruments Keystone timer + +This document provides bindings for the 64-bit timer in the KeyStone +architecture devices. The timer can be configured as a general-purpose 64-bit +timer, dual general-purpose 32-bit timers. When configured as dual 32-bit +timers, each half can operate in conjunction (chain mode) or independently +(unchained mode) of each other. + +It is global timer is a free running up-counter and can generate interrupt +when the counter reaches preset counter values. + +Documentation: +http://www.ti.com/lit/ug/sprugv5a/sprugv5a.pdf + +Required properties: + +- compatible : should be "ti,keystone-timer". +- reg : specifies base physical address and count of the registers. +- interrupts : interrupt generated by the timer. +- clocks : the clock feeding the timer clock. + +Example: + +timer@22f0000 { + compatible = "ti,keystone-timer"; + reg = <0x022f0000 0x80>; + interrupts = <GIC_SPI 110 IRQ_TYPE_EDGE_RISING>; + clocks = <&clktimer15>; +}; diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt index 20468b2a7516..53579197eca2 100644 --- a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt +++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt @@ -8,9 +8,50 @@ Required properties: - interrupts : <interrupt mapping for UFS host controller IRQ> - reg : <registers mapping> +Optional properties: +- vdd-hba-supply : phandle to UFS host controller supply regulator node +- vcc-supply : phandle to VCC supply regulator node +- vccq-supply : phandle to VCCQ supply regulator node +- vccq2-supply : phandle to VCCQ2 supply regulator node +- vcc-supply-1p8 : For embedded UFS devices, valid VCC range is 1.7-1.95V + or 2.7-3.6V. This boolean property when set, specifies + to use low voltage range of 1.7-1.95V. Note for external + UFS cards this property is invalid and valid VCC range is + always 2.7-3.6V. +- vcc-max-microamp : specifies max. load that can be drawn from vcc supply +- vccq-max-microamp : specifies max. load that can be drawn from vccq supply +- vccq2-max-microamp : specifies max. load that can be drawn from vccq2 supply +- <name>-fixed-regulator : boolean property specifying that <name>-supply is a fixed regulator + +- clocks : List of phandle and clock specifier pairs +- clock-names : List of clock input name strings sorted in the same + order as the clocks property. +- freq-table-hz : Array of <min max> operating frequencies stored in the same + order as the clocks property. If this property is not + defined or a value in the array is "0" then it is assumed + that the frequency is set by the parent clock or a + fixed rate clock source. + +Note: If above properties are not defined it can be assumed that the supply +regulators or clocks are always on. + Example: ufshc@0xfc598000 { compatible = "jedec,ufs-1.1"; reg = <0xfc598000 0x800>; interrupts = <0 28 0>; + + vdd-hba-supply = <&xxx_reg0>; + vdd-hba-fixed-regulator; + vcc-supply = <&xxx_reg1>; + vcc-supply-1p8; + vccq-supply = <&xxx_reg2>; + vccq2-supply = <&xxx_reg3>; + vcc-max-microamp = 500000; + vccq-max-microamp = 200000; + vccq2-max-microamp = 200000; + + clocks = <&core 0>, <&ref 0>, <&iface 0>; + clock-names = "core_clk", "ref_clk", "iface_clk"; + freq-table-hz = <100000000 200000000>, <0 0>, <0 0>; }; diff --git a/Documentation/devicetree/bindings/usb/atmel-usb.txt b/Documentation/devicetree/bindings/usb/atmel-usb.txt index 55f51af08bc7..bc2222ca3f2a 100644 --- a/Documentation/devicetree/bindings/usb/atmel-usb.txt +++ b/Documentation/devicetree/bindings/usb/atmel-usb.txt @@ -57,8 +57,8 @@ Required properties: - ep childnode: To specify the number of endpoints and their properties. Optional properties: - - atmel,vbus-gpio: If present, specifies a gpio that needs to be - activated for the bus to be powered. + - atmel,vbus-gpio: If present, specifies a gpio that allows to detect whether + vbus is present (USB is connected). Required child node properties: - name: Name of the endpoint. diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt index b4b5b7906c88..38a548001e3a 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt @@ -4,6 +4,7 @@ Required properties: - compatible: Should be "fsl,imx27-usb" - reg: Should contain registers location and length - interrupts: Should contain controller interrupt +- fsl,usbphy: phandle of usb phy that connects to the port Recommended properies: - phy_type: the type of the phy connected to the core. Should be one @@ -12,12 +13,13 @@ Recommended properies: - dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg" Optional properties: -- fsl,usbphy: phandler of usb phy that connects to the only one port - fsl,usbmisc: phandler of non-core register device, with one argument that indicate usb controller index - vbus-supply: regulator for vbus - disable-over-current: disable over current detect - external-vbus-divider: enables off-chip resistor divider for Vbus +- maximum-speed: limit the maximum connection speed to "full-speed". +- tpl-support: TPL (Targeted Peripheral List) feature for targeted hosts Examples: usb@02184000 { /* USB OTG */ @@ -28,4 +30,6 @@ usb@02184000 { /* USB OTG */ fsl,usbmisc = <&usbmisc 0>; disable-over-current; external-vbus-divider; + maximum-speed = "full-speed"; + tpl-support; }; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-qcom.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-qcom.txt new file mode 100644 index 000000000000..f2899b550939 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-qcom.txt @@ -0,0 +1,17 @@ +Qualcomm CI13xxx (Chipidea) USB controllers + +Required properties: +- compatible: should contain "qcom,ci-hdrc" +- reg: offset and length of the register set in the memory map +- interrupts: interrupt-specifier for the controller interrupt. +- usb-phy: phandle for the PHY device +- dr_mode: Should be "peripheral" + +Examples: + gadget@f9a55000 { + compatible = "qcom,ci-hdrc"; + reg = <0xf9a55000 0x400>; + dr_mode = "peripheral"; + interrupts = <0 134 0>; + usb-phy = <&usbphy0>; + }; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-zevio.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-zevio.txt new file mode 100644 index 000000000000..abbcb2aea38c --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-zevio.txt @@ -0,0 +1,17 @@ +* LSI Zevio USB OTG Controller + +Required properties: +- compatible: Should be "lsi,zevio-usb" +- reg: Should contain registers location and length +- interrupts: Should contain controller interrupt + +Optional properties: +- vbus-supply: regulator for vbus + +Examples: + usb0: usb@b0000000 { + reg = <0xb0000000 0x1000>; + compatible = "lsi,zevio-usb"; + interrupts = <8>; + vbus-supply = <&vbus_reg>; + }; diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt index b8b6871f116f..482f815363ef 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.txt +++ b/Documentation/devicetree/bindings/usb/dwc2.txt @@ -4,6 +4,9 @@ Platform DesignWare HS OTG USB 2.0 controller Required properties: - compatible : One of: - brcm,bcm2835-usb: The DWC2 USB controller instance in the BCM2835 SoC. + - rockchip,rk3066-usb: The DWC2 USB controller instance in the rk3066 Soc; + - "rockchip,rk3188-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3188 Soc; + - "rockchip,rk3288-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3288 Soc; - snps,dwc2: A generic DWC2 USB controller with default parameters. - reg : Should contain 1 register range (address and length) - interrupts : Should contain 1 interrupt @@ -13,8 +16,10 @@ Refer to clk/clock-bindings.txt for generic clock consumer properties Optional properties: - phys: phy provider specifier -- phy-names: shall be "device" +- phy-names: shall be "usb2-phy" Refer to phy/phy-bindings.txt for generic phy consumer properties +- dr_mode: shall be one of "host", "peripheral" and "otg" + Refer to usb/generic.txt Example: diff --git a/Documentation/devicetree/bindings/usb/dwc3-st.txt b/Documentation/devicetree/bindings/usb/dwc3-st.txt new file mode 100644 index 000000000000..f9d70252bbb2 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/dwc3-st.txt @@ -0,0 +1,68 @@ +ST DWC3 glue logic + +This file documents the parameters for the dwc3-st driver. +This driver controls the glue logic used to configure the dwc3 core on +STiH407 based platforms. + +Required properties: + - compatible : must be "st,stih407-dwc3" + - reg : glue logic base address and USB syscfg ctrl register offset + - reg-names : should be "reg-glue" and "syscfg-reg" + - st,syscon : should be phandle to system configuration node which + encompasses the glue registers + - resets : list of phandle and reset specifier pairs. There should be two entries, one + for the powerdown and softreset lines of the usb3 IP + - reset-names : list of reset signal names. Names should be "powerdown" and "softreset" +See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt +See: Documentation/devicetree/bindings/reset/reset.txt + + - #address-cells, #size-cells : should be '1' if the device has sub-nodes + with 'reg' property + + - pinctl-names : A pinctrl state named "default" must be defined +See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt + + - pinctrl-0 : Pin control group +See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt + + - ranges : allows valid 1:1 translation between child's address space and + parent's address space + +Sub-nodes: +The dwc3 core should be added as subnode to ST DWC3 glue as shown in the +example below. The DT binding details of dwc3 can be found in: +Documentation/devicetree/bindings/usb/dwc3.txt + +NB: The dr_mode property described in [1] is NOT optional for this driver, as the default value +is "otg", which isn't supported by this SoC. Valid dr_mode values for dwc3-st are either "host" +or "device". + +[1] Documentation/devicetree/bindings/usb/generic.txt + +Example: + +st_dwc3: dwc3@8f94000 { + status = "disabled"; + compatible = "st,stih407-dwc3"; + reg = <0x08f94000 0x1000>, <0x110 0x4>; + reg-names = "reg-glue", "syscfg-reg"; + st,syscfg = <&syscfg_core>; + resets = <&powerdown STIH407_USB3_POWERDOWN>, + <&softreset STIH407_MIPHY2_SOFTRESET>; + reset-names = "powerdown", + "softreset"; + #address-cells = <1>; + #size-cells = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb3>; + ranges; + + dwc3: dwc3@9900000 { + compatible = "snps,dwc3"; + reg = <0x09900000 0x100000>; + interrupts = <GIC_SPI 155 IRQ_TYPE_NONE>; + dr_mode = "host"; + phys-names = "usb2-phy", "usb3-phy"; + phys = <&usb2_picophy2>, <&phy_port2 MIPHY_TYPE_USB>; + }; +}; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index e807635f9e1c..471366d6a129 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -6,11 +6,13 @@ Required properties: - compatible: must be "snps,dwc3" - reg : Address and length of the register set for the device - interrupts: Interrupts used by the dwc3 controller. + +Optional properties: - usb-phy : array of phandle for the PHY device. The first element in the array is expected to be a handle to the USB2/HS PHY and the second element is expected to be a handle to the USB3/SS PHY - -Optional properties: + - phys: from the *Generic PHY* bindings + - phy-names: from the *Generic PHY* bindings - tx-fifo-resize: determines if the FIFO *has* to be reallocated. This is usually a subnode to DWC3 glue to which it is connected. diff --git a/Documentation/devicetree/bindings/usb/ehci-omap.txt b/Documentation/devicetree/bindings/usb/ehci-omap.txt index 485a9a1efa7a..3dc231c832b0 100644 --- a/Documentation/devicetree/bindings/usb/ehci-omap.txt +++ b/Documentation/devicetree/bindings/usb/ehci-omap.txt @@ -21,7 +21,7 @@ Documentation/devicetree/bindings/mfd/omap-usb-host.txt Example for OMAP4: usbhsehci: ehci@4a064c00 { - compatible = "ti,ehci-omap", "usb-ehci"; + compatible = "ti,ehci-omap"; reg = <0x4a064c00 0x400>; interrupts = <0 77 0x4>; }; diff --git a/Documentation/devicetree/bindings/usb/ehci-orion.txt b/Documentation/devicetree/bindings/usb/ehci-orion.txt index 6bc09ec14c4d..17c3bc858b86 100644 --- a/Documentation/devicetree/bindings/usb/ehci-orion.txt +++ b/Documentation/devicetree/bindings/usb/ehci-orion.txt @@ -6,6 +6,11 @@ Required properties: region. - interrupts: The EHCI interrupt +Optional properties: +- clocks: reference to the clock +- phys: reference to the USB PHY +- phy-names: name of the USB PHY, should be "usb" + Example: ehci@50000 { diff --git a/Documentation/devicetree/bindings/usb/ehci-st.txt b/Documentation/devicetree/bindings/usb/ehci-st.txt new file mode 100644 index 000000000000..fb45fa5770bb --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ehci-st.txt @@ -0,0 +1,39 @@ +ST USB EHCI controller + +Required properties: + - compatible : must be "st,st-ehci-300x" + - reg : physical base addresses of the controller and length of memory mapped + region + - interrupts : one EHCI interrupt should be described here + - pinctrl-names : a pinctrl state named "default" must be defined + - pinctrl-0 : phandle referencing pin configuration of the USB controller +See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt + - clocks : phandle list of usb clocks + - clock-names : should be "ic" for interconnect clock and "clk48" +See: Documentation/devicetree/bindings/clock/clock-bindings.txt + + - phys : phandle for the PHY device + - phy-names : should be "usb" + - resets : phandle + reset specifier pairs to the powerdown and softreset lines + of the USB IP + - reset-names : should be "power" and "softreset" +See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt +See: Documentation/devicetree/bindings/reset/reset.txt + +Example: + + ehci1: usb@0xfe203e00 { + compatible = "st,st-ehci-300x"; + reg = <0xfe203e00 0x100>; + interrupts = <GIC_SPI 148 IRQ_TYPE_NONE>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb1>; + clocks = <&clk_s_a1_ls 0>; + phys = <&usb2_phy>; + phy-names = "usb"; + status = "okay"; + + resets = <&powerdown STIH416_USB1_POWERDOWN>, + <&softreset STIH416_USB1_SOFTRESET>; + reset-names = "power", "softreset"; + }; diff --git a/Documentation/devicetree/bindings/usb/exynos-usb.txt b/Documentation/devicetree/bindings/usb/exynos-usb.txt index d967ba16de60..a3b5990d0f2c 100644 --- a/Documentation/devicetree/bindings/usb/exynos-usb.txt +++ b/Documentation/devicetree/bindings/usb/exynos-usb.txt @@ -12,6 +12,13 @@ Required properties: - interrupts: interrupt number to the cpu. - clocks: from common clock binding: handle to usb clock. - clock-names: from common clock binding: Shall be "usbhost". + - port: if in the SoC there are EHCI phys, they should be listed here. + One phy per port. Each port should have following entries: + - reg: port number on EHCI controller, e.g + On Exynos5250, port 0 is USB2.0 otg phy + port 1 is HSIC phy0 + port 2 is HSIC phy1 + - phys: from the *Generic PHY* bindings; specifying phy used by port. Optional properties: - samsung,vbus-gpio: if present, specifies the GPIO that @@ -27,6 +34,14 @@ Example: clocks = <&clock 285>; clock-names = "usbhost"; + + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + phys = <&usb2phy 1>; + status = "disabled"; + }; }; OHCI @@ -38,6 +53,13 @@ Required properties: - interrupts: interrupt number to the cpu. - clocks: from common clock binding: handle to usb clock. - clock-names: from common clock binding: Shall be "usbhost". + - port: if in the SoC there are OHCI phys, they should be listed here. + One phy per port. Each port should have following entries: + - reg: port number on OHCI controller, e.g + On Exynos5250, port 0 is USB2.0 otg phy + port 1 is HSIC phy0 + port 2 is HSIC phy1 + - phys: from the *Generic PHY* bindings, specifying phy used by port. Example: usb@12120000 { @@ -47,6 +69,15 @@ Example: clocks = <&clock 285>; clock-names = "usbhost"; + + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + phys = <&usb2phy 1>; + status = "disabled"; + }; + }; DWC3 diff --git a/Documentation/devicetree/bindings/usb/fsl-usb.txt b/Documentation/devicetree/bindings/usb/fsl-usb.txt index bd5723f0b67e..4779c029b675 100644 --- a/Documentation/devicetree/bindings/usb/fsl-usb.txt +++ b/Documentation/devicetree/bindings/usb/fsl-usb.txt @@ -8,7 +8,9 @@ and additions : Required properties : - compatible : Should be "fsl-usb2-mph" for multi port host USB controllers, or "fsl-usb2-dr" for dual role USB controllers - or "fsl,mpc5121-usb2-dr" for dual role USB controllers of MPC5121 + or "fsl,mpc5121-usb2-dr" for dual role USB controllers of MPC5121. + Wherever applicable, the IP version of the USB controller should + also be mentioned (for eg. fsl-usb2-dr-v2.2 for bsc9132). - phy_type : For multi port host USB controllers, should be one of "ulpi", or "serial". For dual role USB controllers, should be one of "ulpi", "utmi", "utmi_wide", or "serial". diff --git a/Documentation/devicetree/bindings/usb/gr-udc.txt b/Documentation/devicetree/bindings/usb/gr-udc.txt index 0c5118f7a916..e9445224fabd 100644 --- a/Documentation/devicetree/bindings/usb/gr-udc.txt +++ b/Documentation/devicetree/bindings/usb/gr-udc.txt @@ -12,17 +12,23 @@ Required properties: - reg : Address and length of the register set for the device -- interrupts : Interrupt numbers for this device +- interrupts : Interrupt numbers for this device. Either one interrupt number + for all interrupts, or one for status related interrupts, one for IN + endpoint related interrupts and one for OUT endpoint related interrupts. Optional properties: -- epobufsizes : An array of buffer sizes for OUT endpoints. If the property is - not present, or for endpoints outside of the array, 1024 is assumed by - the driver. - -- epibufsizes : An array of buffer sizes for IN endpoints. If the property is - not present, or for endpoints outside of the array, 1024 is assumed by - the driver. +- epobufsizes : Array of buffer sizes for OUT endpoints when they differ + from the default size of 1024. The array is indexed by the OUT endpoint + number. If the property is present it typically contains one entry for + each OUT endpoint of the core. Fewer entries overrides the default sizes + only for as many endpoints as the array contains. + +- epibufsizes : Array of buffer sizes for IN endpoints when they differ + from the default size of 1024. The array is indexed by the IN endpoint + number. If the property is present it typically contains one entry for + each IN endpoint of the core. Fewer entries overrides the default sizes + only for as many endpoints as the array contains. For further information look in the documentation for the GLIB IP core library: http://www.gaisler.com/products/grlib/grip.pdf diff --git a/Documentation/devicetree/bindings/usb/msm-hsusb.txt b/Documentation/devicetree/bindings/usb/msm-hsusb.txt index 5ea26c631e3a..2826f2af503a 100644 --- a/Documentation/devicetree/bindings/usb/msm-hsusb.txt +++ b/Documentation/devicetree/bindings/usb/msm-hsusb.txt @@ -15,3 +15,81 @@ Example EHCI controller device node: usb-phy = <&usb_otg>; }; +USB PHY with optional OTG: + +Required properties: +- compatible: Should contain: + "qcom,usb-otg-ci" for chipsets with ChipIdea 45nm PHY + "qcom,usb-otg-snps" for chipsets with Synopsys 28nm PHY + +- regs: Offset and length of the register set in the memory map +- interrupts: interrupt-specifier for the OTG interrupt. + +- clocks: A list of phandle + clock-specifier pairs for the + clocks listed in clock-names +- clock-names: Should contain the following: + "phy" USB PHY reference clock + "core" Protocol engine clock + "iface" Interface bus clock + "alt_core" Protocol engine clock for targets with asynchronous + reset methodology. (optional) + +- vdccx-supply: phandle to the regulator for the vdd supply for + digital circuit operation. +- v1p8-supply: phandle to the regulator for the 1.8V supply +- v3p3-supply: phandle to the regulator for the 3.3V supply + +- resets: A list of phandle + reset-specifier pairs for the + resets listed in reset-names +- reset-names: Should contain the following: + "phy" USB PHY controller reset + "link" USB LINK controller reset + +- qcom,otg-control: OTG control (VBUS and ID notifications) can be one of + 1 - PHY control + 2 - PMIC control + +Optional properties: +- dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg" + +- qcom,phy-init-sequence: PHY configuration sequence values. This is related to Device + Mode Eye Diagram test. Start address at which these values will be + written is ULPI_EXT_VENDOR_SPECIFIC. Value of -1 is reserved as + "do not overwrite default value at this address". + For example: qcom,phy-init-sequence = < -1 0x63 >; + Will update only value at address ULPI_EXT_VENDOR_SPECIFIC + 1. + +- qcom,phy-num: Select number of pyco-phy to use, can be one of + 0 - PHY one, default + 1 - Second PHY + Some platforms may have configuration to allow USB + controller work with any of the two HSPHYs present. + +- qcom,vdd-levels: This property must be a list of three integer values + (no, min, max) where each value represents either a voltage + in microvolts or a value corresponding to voltage corner. + +Example HSUSB OTG controller device node: + + usb@f9a55000 { + compatible = "qcom,usb-otg-snps"; + reg = <0xf9a55000 0x400>; + interrupts = <0 134 0>; + dr_mode = "peripheral"; + + clocks = <&gcc GCC_XO_CLK>, <&gcc GCC_USB_HS_SYSTEM_CLK>, + <&gcc GCC_USB_HS_AHB_CLK>; + + clock-names = "phy", "core", "iface"; + + vddcx-supply = <&pm8841_s2_corner>; + v1p8-supply = <&pm8941_l6>; + v3p3-supply = <&pm8941_l24>; + + resets = <&gcc GCC_USB2A_PHY_BCR>, <&gcc GCC_USB_HS_BCR>; + reset-names = "phy", "link"; + + qcom,otg-control = <1>; + qcom,phy-init-sequence = < -1 0x63 >; + qcom,vdd-levels = <1 5 7>; + }; diff --git a/Documentation/devicetree/bindings/usb/mxs-phy.txt b/Documentation/devicetree/bindings/usb/mxs-phy.txt index 5835b27146ea..379b84a567cc 100644 --- a/Documentation/devicetree/bindings/usb/mxs-phy.txt +++ b/Documentation/devicetree/bindings/usb/mxs-phy.txt @@ -1,13 +1,21 @@ * Freescale MXS USB Phy Device Required properties: -- compatible: Should be "fsl,imx23-usbphy" +- compatible: should contain: + * "fsl,imx23-usbphy" for imx23 and imx28 + * "fsl,imx6q-usbphy" for imx6dq and imx6dl + * "fsl,imx6sl-usbphy" for imx6sl + * "fsl,vf610-usbphy" for Vybrid vf610 + * "fsl,imx6sx-usbphy" for imx6sx + "fsl,imx23-usbphy" is still a fallback for other strings - reg: Should contain registers location and length - interrupts: Should contain phy interrupt +- fsl,anatop: phandle for anatop register, it is only for imx6 SoC series Example: usbphy1: usbphy@020c9000 { compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy"; reg = <0x020c9000 0x1000>; interrupts = <0 44 0x04>; + fsl,anatop = <&anatop>; }; diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt index ba797d3e6326..c9205fbf26e2 100644 --- a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt @@ -20,6 +20,12 @@ Required properties : Present if phy_type == utmi. - ulpi-link: The clock Tegra provides to the ULPI PHY (cdev2). Present if phy_type == ulpi, and ULPI link mode is in use. + - resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names : Must include the following entries: + - usb: The PHY's own reset signal. + - utmi-pads: The reset of the PHY containing the chip-wide UTMI pad control + registers. Required even if phy_type == ulpi. Required properties for phy_type == ulpi: - nvidia,phy-reset-gpio : The GPIO used to reset the PHY. @@ -56,6 +62,8 @@ Optional properties: host means this is a host controller peripheral means it is device controller otg means it can operate as either ("on the go") + - nvidia,has-utmi-pad-registers : boolean indicates whether this controller + contains the UTMI pad control registers common to all USB controllers. VBUS control (required for dr_mode == otg, optional for dr_mode == host): - vbus-supply: regulator for VBUS diff --git a/Documentation/devicetree/bindings/usb/ohci-omap3.txt b/Documentation/devicetree/bindings/usb/ohci-omap3.txt index 14ab42812a8e..ce8c47cff6d0 100644 --- a/Documentation/devicetree/bindings/usb/ohci-omap3.txt +++ b/Documentation/devicetree/bindings/usb/ohci-omap3.txt @@ -9,7 +9,7 @@ Required properties: Example for OMAP4: usbhsohci: ohci@4a064800 { - compatible = "ti,ohci-omap3", "usb-ohci"; + compatible = "ti,ohci-omap3"; reg = <0x4a064800 0x400>; interrupts = <0 76 0x4>; }; diff --git a/Documentation/devicetree/bindings/usb/ohci-st.txt b/Documentation/devicetree/bindings/usb/ohci-st.txt new file mode 100644 index 000000000000..6d8393748da2 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ohci-st.txt @@ -0,0 +1,37 @@ +ST USB OHCI controller + +Required properties: + + - compatible : must be "st,st-ohci-300x" + - reg : physical base addresses of the controller and length of memory mapped + region + - interrupts : one OHCI controller interrupt should be described here + - clocks : phandle list of usb clocks + - clock-names : should be "ic" for interconnect clock and "clk48" +See: Documentation/devicetree/bindings/clock/clock-bindings.txt + + - phys : phandle for the PHY device + - phy-names : should be "usb" + + - resets : phandle to the powerdown and reset controller for the USB IP + - reset-names : should be "power" and "softreset". +See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt +See: Documentation/devicetree/bindings/reset/reset.txt + +Example: + + ohci0: usb@0xfe1ffc00 { + compatible = "st,st-ohci-300x"; + reg = <0xfe1ffc00 0x100>; + interrupts = <GIC_SPI 149 IRQ_TYPE_NONE>; + clocks = <&clk_s_a1_ls 0>, + <&clockgen_b0 0>; + clock-names = "ic", "clk48"; + phys = <&usb2_phy>; + phy-names = "usb"; + status = "okay"; + + resets = <&powerdown STIH416_USB0_POWERDOWN>, + <&softreset STIH416_USB0_SOFTRESET>; + reset-names = "power", "softreset"; + }; diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt index c495135115cb..38d9bb8507cf 100644 --- a/Documentation/devicetree/bindings/usb/omap-usb.txt +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -44,7 +44,9 @@ Board specific device node entry }; OMAP DWC3 GLUE - - compatible : Should be "ti,dwc3" + - compatible : Should be + * "ti,dwc3" for OMAP5 and DRA7 + * "ti,am437x-dwc3" for AM437x - ti,hwmods : Should be "usb_otg_ss" - reg : Address and length of the register set for the device. - interrupts : The irq number of this device that is used to interrupt the @@ -76,27 +78,3 @@ omap_dwc3 { ranges; }; -OMAP CONTROL USB - -Required properties: - - compatible: Should be one of - "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4. - "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register - e.g. USB2_PHY on OMAP5. - "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control - e.g. USB3 PHY and SATA PHY on OMAP5. - "ti,control-phy-dra7usb2" - if it has power down register like USB2 PHY on - DRA7 platform. - "ti,control-phy-am437usb2" - if it has power down register like USB2 PHY on - AM437 platform. - - reg : Address and length of the register set for the device. It contains - the address of "otghs_control" for control-phy-otghs or "power" register - for other types. - - reg-names: should be "otghs_control" control-phy-otghs and "power" for - other types. - -omap_control_usb: omap-control-usb@4a002300 { - compatible = "ti,control-phy-otghs"; - reg = <0x4a00233c 0x4>; - reg-names = "otghs_control"; -}; diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt new file mode 100644 index 000000000000..ca164e71dd50 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt @@ -0,0 +1,66 @@ +Qualcomm SuperSpeed DWC3 USB SoC controller + +Required properties: +- compatible: should contain "qcom,dwc3" +- clocks: A list of phandle + clock-specifier pairs for the + clocks listed in clock-names +- clock-names: Should contain the following: + "core" Master/Core clock, have to be >= 125 MHz for SS + operation and >= 60MHz for HS operation + +Optional clocks: + "iface" System bus AXI clock. Not present on all platforms + "sleep" Sleep clock, used when USB3 core goes into low + power mode (U3). + +Required child node: +A child node must exist to represent the core DWC3 IP block. The name of +the node is not important. The content of the node is defined in dwc3.txt. + +Phy documentation is provided in the following places: +Documentation/devicetree/bindings/phy/qcom,dwc3-usb-phy.txt + +Example device nodes: + + hs_phy: phy@100f8800 { + compatible = "qcom,dwc3-hs-usb-phy"; + reg = <0x100f8800 0x30>; + clocks = <&gcc USB30_0_UTMI_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "ok"; + }; + + ss_phy: phy@100f8830 { + compatible = "qcom,dwc3-ss-usb-phy"; + reg = <0x100f8830 0x30>; + clocks = <&gcc USB30_0_MASTER_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "ok"; + }; + + usb3_0: usb30@0 { + compatible = "qcom,dwc3"; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&gcc USB30_0_MASTER_CLK>; + clock-names = "core"; + + ranges; + + status = "ok"; + + dwc3@10000000 { + compatible = "snps,dwc3"; + reg = <0x10000000 0xcd00>; + interrupts = <0 205 0x4>; + phys = <&hs_phy>, <&ss_phy>; + phy-names = "usb2-phy", "usb3-phy"; + tx-fifo-resize; + dr_mode = "host"; + }; + }; + diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt new file mode 100644 index 000000000000..b08c903f8668 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt @@ -0,0 +1,24 @@ +Renesas Electronics USBHS driver + +Required properties: + - compatible: Must contain one of the following: + - "renesas,usbhs-r8a7790" + - "renesas,usbhs-r8a7791" + - reg: Base address and length of the register for the USBHS + - interrupts: Interrupt specifier for the USBHS + - clocks: A list of phandle + clock specifier pairs + +Optional properties: + - renesas,buswait: Integer to use BUSWAIT register + - renesas,enable-gpio: A gpio specifier to check GPIO determining if USB + function should be enabled + - phys: phandle + phy specifier pair + - phy-names: must be "usb" + +Example: + usbhs: usb@e6590000 { + compatible = "renesas,usbhs-r8a7790"; + reg = <0 0xe6590000 0 0x100>; + interrupts = <0 107 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7790_CLK_HSUSB>; + }; diff --git a/Documentation/devicetree/bindings/usb/udc-xilinx.txt b/Documentation/devicetree/bindings/usb/udc-xilinx.txt new file mode 100644 index 000000000000..47b4e397a08d --- /dev/null +++ b/Documentation/devicetree/bindings/usb/udc-xilinx.txt @@ -0,0 +1,18 @@ +Xilinx USB2 device controller + +Required properties: +- compatible : Should be "xlnx,usb2-device-4.00.a" +- reg : Physical base address and size of the USB2 + device registers map. +- interrupts : Should contain single irq line of USB2 device + controller +- xlnx,has-builtin-dma : if DMA is included + +Example: + axi-usb2-device@42e00000 { + compatible = "xlnx,usb2-device-4.00.a"; + interrupts = <0x0 0x39 0x1>; + reg = <0x42e00000 0x10000>; + xlnx,has-builtin-dma; + }; + diff --git a/Documentation/devicetree/bindings/usb/usb-ehci.txt b/Documentation/devicetree/bindings/usb/usb-ehci.txt index fa18612f757b..43c1a4e06767 100644 --- a/Documentation/devicetree/bindings/usb/usb-ehci.txt +++ b/Documentation/devicetree/bindings/usb/usb-ehci.txt @@ -1,19 +1,21 @@ USB EHCI controllers Required properties: - - compatible : should be "usb-ehci". + - compatible : should be "generic-ehci". - reg : should contain at least address and length of the standard EHCI register set for the device. Optional platform-dependent registers (debug-port or other) can be also specified here, but only after definition of standard EHCI registers. - interrupts : one EHCI interrupt should be described here. -If device registers are implemented in big endian mode, the device -node should have "big-endian-regs" property. -If controller implementation operates with big endian descriptors, -"big-endian-desc" property should be specified. -If both big endian registers and descriptors are used by the controller -implementation, "big-endian" property can be specified instead of having -both "big-endian-regs" and "big-endian-desc". + +Optional properties: + - big-endian-regs : boolean, set this for hcds with big-endian registers + - big-endian-desc : boolean, set this for hcds with big-endian descriptors + - big-endian : boolean, for hcds with big-endian-regs + big-endian-desc + - clocks : a list of phandle + clock specifier pairs + - phys : phandle + phy specifier pair + - phy-names : "usb" + - resets : phandle + reset specifier pair Example (Sequoia 440EPx): ehci@e0000300 { @@ -23,3 +25,13 @@ Example (Sequoia 440EPx): reg = <0 e0000300 90 0 e0000390 70>; big-endian; }; + +Example (Allwinner sun4i A10 SoC): + ehci0: usb@01c14000 { + compatible = "allwinner,sun4i-a10-ehci", "generic-ehci"; + reg = <0x01c14000 0x100>; + interrupts = <39>; + clocks = <&ahb_gates 1>; + phys = <&usbphy 1>; + phy-names = "usb"; + }; diff --git a/Documentation/devicetree/bindings/usb/usb-ohci.txt b/Documentation/devicetree/bindings/usb/usb-ohci.txt new file mode 100644 index 000000000000..b968a1aea995 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-ohci.txt @@ -0,0 +1,26 @@ +USB OHCI controllers + +Required properties: +- compatible : "generic-ohci" +- reg : ohci controller register range (address and length) +- interrupts : ohci controller interrupt + +Optional properties: +- big-endian-regs : boolean, set this for hcds with big-endian registers +- big-endian-desc : boolean, set this for hcds with big-endian descriptors +- big-endian : boolean, for hcds with big-endian-regs + big-endian-desc +- clocks : a list of phandle + clock specifier pairs +- phys : phandle + phy specifier pair +- phy-names : "usb" +- resets : phandle + reset specifier pair + +Example: + + ohci0: usb@01c14400 { + compatible = "allwinner,sun4i-a10-ohci", "generic-ohci"; + reg = <0x01c14400 0x100>; + interrupts = <64>; + clocks = <&usb_clk 6>, <&ahb_gates 2>; + phys = <&usbphy 1>; + phy-names = "usb"; + }; diff --git a/Documentation/devicetree/bindings/usb/usb-phy.txt b/Documentation/devicetree/bindings/usb/usb-phy.txt deleted file mode 100644 index c0245c888982..000000000000 --- a/Documentation/devicetree/bindings/usb/usb-phy.txt +++ /dev/null @@ -1,48 +0,0 @@ -USB PHY - -OMAP USB2 PHY - -Required properties: - - compatible: Should be "ti,omap-usb2" - - reg : Address and length of the register set for the device. - - #phy-cells: determine the number of cells that should be given in the - phandle while referencing this phy. - -Optional properties: - - ctrl-module : phandle of the control module used by PHY driver to power on - the PHY. - -This is usually a subnode of ocp2scp to which it is connected. - -usb2phy@4a0ad080 { - compatible = "ti,omap-usb2"; - reg = <0x4a0ad080 0x58>; - ctrl-module = <&omap_control_usb>; - #phy-cells = <0>; -}; - -OMAP USB3 PHY - -Required properties: - - compatible: Should be "ti,omap-usb3" - - reg : Address and length of the register set for the device. - - reg-names: The names of the register addresses corresponding to the registers - filled in "reg". - - #phy-cells: determine the number of cells that should be given in the - phandle while referencing this phy. - -Optional properties: - - ctrl-module : phandle of the control module used by PHY driver to power on - the PHY. - -This is usually a subnode of ocp2scp to which it is connected. - -usb3phy@4a084400 { - compatible = "ti,omap-usb3"; - reg = <0x4a084400 0x80>, - <0x4a084800 0x64>, - <0x4a084c00 0x40>; - reg-names = "phy_rx", "phy_tx", "pll_ctrl"; - ctrl-module = <&omap_control_usb>; - #phy-cells = <0>; -}; diff --git a/Documentation/devicetree/bindings/usb/platform-uhci.txt b/Documentation/devicetree/bindings/usb/usb-uhci.txt index a4fb0719d157..298133416c97 100644 --- a/Documentation/devicetree/bindings/usb/platform-uhci.txt +++ b/Documentation/devicetree/bindings/usb/usb-uhci.txt @@ -2,14 +2,14 @@ Generic Platform UHCI Controller ----------------------------------------------------- Required properties: -- compatible : "platform-uhci" +- compatible : "generic-uhci" (deprecated: "platform-uhci") - reg : Should contain 1 register ranges(address and length) - interrupts : UHCI controller interrupt Example: uhci@d8007b00 { - compatible = "platform-uhci"; + compatible = "generic-uhci"; reg = <0xd8007b00 0x200>; interrupts = <43>; }; diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt index 5752df0e17a2..86f67f0886bc 100644 --- a/Documentation/devicetree/bindings/usb/usb-xhci.txt +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -1,14 +1,21 @@ USB xHCI controllers Required properties: - - compatible: should be "xhci-platform". + - compatible: should be one of "generic-xhci", + "marvell,armada-375-xhci", "marvell,armada-380-xhci", + "renesas,xhci-r8a7790", "renesas,xhci-r8a7791" (deprecated: + "xhci-platform"). - reg: should contain address and length of the standard XHCI register set for the device. - interrupts: one XHCI interrupt should be described here. +Optional properties: + - clocks: reference to a clock + - usb3-lpm-capable: determines if platform is USB3 LPM capable + Example: usb@f0931000 { - compatible = "xhci-platform"; + compatible = "generic-xhci"; reg = <0xf0931000 0x8c8>; interrupts = <0x0 0x4e 0x0>; }; diff --git a/Documentation/devicetree/bindings/usb/usb3503.txt b/Documentation/devicetree/bindings/usb/usb3503.txt index a018da4a7ad7..52493b1480e2 100644 --- a/Documentation/devicetree/bindings/usb/usb3503.txt +++ b/Documentation/devicetree/bindings/usb/usb3503.txt @@ -8,13 +8,21 @@ Optional properties: if I2C is used. - connect-gpios: Should specify GPIO for connect. - disabled-ports: Should specify the ports unused. - '1' or '2' or '3' are availe for this property to describe the port - number. 1~3 property values are possible to be desribed. + '1' or '2' or '3' are available for this property to describe the port + number. 1~3 property values are possible to be described. Do not describe this property if all ports have to be enabled. - intn-gpios: Should specify GPIO for interrupt. - reset-gpios: Should specify GPIO for reset. - initial-mode: Should specify initial mode. (1 for HUB mode, 2 for STANDBY mode) +- refclk: Clock used for driving REFCLK signal (optional, if not provided + the driver assumes that clock signal is always available, its + rate is specified by REF_SEL pins and a value from the primary + reference clock frequencies table is used) +- refclk-frequency: Frequency of the REFCLK signal as defined by REF_SEL + pins (optional, if not provided, driver will not set rate of the + REFCLK signal and assume that a value from the primary reference + clock frequencies table is used) Examples: usb3503@08 { diff --git a/Documentation/devicetree/bindings/usb/usbmisc-imx.txt b/Documentation/devicetree/bindings/usb/usbmisc-imx.txt index 97ce94e1a6cc..c101a4b17131 100644 --- a/Documentation/devicetree/bindings/usb/usbmisc-imx.txt +++ b/Documentation/devicetree/bindings/usb/usbmisc-imx.txt @@ -4,6 +4,7 @@ Required properties: - #index-cells: Cells used to descibe usb controller index. Should be <1> - compatible: Should be one of below: "fsl,imx6q-usbmisc" for imx6q + "fsl,vf610-usbmisc" for Vybrid vf610 - reg: Should contain registers location and length Examples: diff --git a/Documentation/devicetree/bindings/usb/via,vt8500-ehci.txt b/Documentation/devicetree/bindings/usb/via,vt8500-ehci.txt deleted file mode 100644 index 17b3ad1d97e7..000000000000 --- a/Documentation/devicetree/bindings/usb/via,vt8500-ehci.txt +++ /dev/null @@ -1,15 +0,0 @@ -VIA/Wondermedia VT8500 EHCI Controller ------------------------------------------------------ - -Required properties: -- compatible : "via,vt8500-ehci" -- reg : Should contain 1 register ranges(address and length) -- interrupts : ehci controller interrupt - -Example: - - ehci@d8007900 { - compatible = "via,vt8500-ehci"; - reg = <0xd8007900 0x200>; - interrupts = <43>; - }; diff --git a/Documentation/devicetree/bindings/usb/vt8500-ehci.txt b/Documentation/devicetree/bindings/usb/vt8500-ehci.txt deleted file mode 100644 index 5fb8fd6e250c..000000000000 --- a/Documentation/devicetree/bindings/usb/vt8500-ehci.txt +++ /dev/null @@ -1,12 +0,0 @@ -VIA VT8500 and Wondermedia WM8xxx SoC USB controllers. - -Required properties: - - compatible: Should be "via,vt8500-ehci" or "wm,prizm-ehci". - - reg: Address range of the ehci registers. size should be 0x200 - - interrupts: Should contain the ehci interrupt. - -usb: ehci@D8007100 { - compatible = "wm,prizm-ehci", "usb-ehci"; - reg = <0xD8007100 0x200>; - interrupts = <1>; -}; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 3f900cd51bf0..0d354625299c 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -3,91 +3,172 @@ Device tree binding vendor prefix registry. Keep list in alphabetical order. This isn't an exhaustive list, but you should add new prefixes to it before using them to avoid name-space collisions. +abilis Abilis Systems active-semi Active-Semi International Inc ad Avionic Design GmbH +adapteva Adapteva, Inc. adi Analog Devices, Inc. aeroflexgaisler Aeroflex Gaisler AB ak Asahi Kasei Corp. +allwinner Allwinner Technology Co., Ltd. altr Altera Corp. amcc Applied Micro Circuits Corporation (APM, formally AMCC) +amd Advanced Micro Devices (AMD), Inc. +amlogic Amlogic, Inc. +ams AMS AG amstaos AMS-Taos Inc. apm Applied Micro Circuits Corporation (APM) arm ARM Ltd. +armadeus ARMadeus Systems SARL atmel Atmel Corporation auo AU Optronics Corporation avago Avago Technologies bosch Bosch Sensortec GmbH brcm Broadcom Corporation +buffalo Buffalo, Inc. +calxeda Calxeda capella Capella Microsystems, Inc cavium Cavium, Inc. cdns Cadence Design Systems Inc. +chipidea Chipidea, Inc chrp Common Hardware Reference Platform chunghwa Chunghwa Picture Tubes Ltd. cirrus Cirrus Logic, Inc. +cnm Chips&Media, Inc. cortina Cortina Systems, Inc. +crystalfontz Crystalfontz America, Inc. dallas Maxim Integrated Products (formerly Dallas Semiconductor) davicom DAVICOM Semiconductor, Inc. denx Denx Software Engineering +digi Digi International Inc. +digilent Diglent, Inc. +dlg Dialog Semiconductor +dlink D-Link Corporation +dmo Data Modul AG +ebv EBV Elektronik edt Emerging Display Technologies emmicro EM Microelectronic +energymicro Silicon Laboratories (formerly Energy Micro AS) +epcos EPCOS AG epfl Ecole Polytechnique Fédérale de Lausanne epson Seiko Epson Corp. est ESTeem Wireless Modems +eukrea Eukréa Electromatique +everest Everest Semiconductor Co. Ltd. +excito Excito +fcs Fairchild Semiconductor fsl Freescale Semiconductor GEFanuc GE Fanuc Intelligent Platforms Embedded Systems, Inc. gef GE Fanuc Intelligent Platforms Embedded Systems, Inc. +geniatech Geniatech, Inc. +globalscale Globalscale Technologies, Inc. gmt Global Mixed-mode Technology, Inc. +google Google, Inc. gumstix Gumstix, Inc. +gw Gateworks Corporation haoyu Haoyu Microelectronic Co. Ltd. hisilicon Hisilicon Limited. +honeywell Honeywell hp Hewlett Packard +i2se I2SE GmbH ibm International Business Machines (IBM) idt Integrated Device Technologies, Inc. +iom Iomega Corporation img Imagination Technologies Ltd. +innolux Innolux Corporation +intel Intel Corporation intercontrol Inter Control Group +isee ISEE 2007 S.L. +isil Intersil (deprecated, use isl) isl Intersil karo Ka-Ro electronics GmbH +keymile Keymile GmbH +lacie LaCie +lantiq Lantiq Semiconductor +lenovo Lenovo Group Ltd. lg LG Corporation linux Linux-specific binding lsi LSI Corp. (LSI Logic) +lltc Linear Technology Corporation marvell Marvell Technology Group Ltd. maxim Maxim Integrated Products +mediatek MediaTek Inc. +merrii Merrii Technology Co., Ltd. +micrel Micrel Inc. microchip Microchip Technology Inc. +micron Micron Technology Inc. +mitsubishi Mitsubishi Electric Corporation mosaixtech Mosaix Technologies, Inc. +moxa Moxa +mpl MPL AG +mundoreader Mundo Reader S.L. +murata Murata Manufacturing Co., Ltd. +mxicy Macronix International Co., Ltd. national National Semiconductor +neonode Neonode Inc. +netgear NETGEAR +newhaven Newhaven Display International nintendo Nintendo +nokia Nokia nvidia NVIDIA nxp NXP Semiconductors onnn ON Semiconductor Corp. +opencores OpenCores.org panasonic Panasonic Corporation phytec PHYTEC Messtechnik GmbH picochip Picochip Ltd +plathome Plat'Home Co., Ltd. +pixcir PIXCIR MICROELECTRONICS Co., Ltd powervr PowerVR (deprecated, use img) qca Qualcomm Atheros, Inc. -qcom Qualcomm, Inc. +qcom Qualcomm Technologies, Inc +qnap QNAP Systems, Inc. +radxa Radxa +raidsonic RaidSonic Technology GmbH ralink Mediatek/Ralink Technology Corp. ramtron Ramtron International realtek Realtek Semiconductor Corp. renesas Renesas Electronics Corporation +ricoh Ricoh Co. Ltd. rockchip Fuzhou Rockchip Electronics Co., Ltd samsung Samsung Semiconductor +sandisk Sandisk Corporation sbs Smart Battery System schindler Schindler +seagate Seagate Technology PLC sil Silicon Image silabs Silicon Laboratories simtek +sii Seiko Instruments, Inc. +silergy Silergy Corp. sirf SiRF Technology, Inc. -snps Synopsys, Inc. +sitronix Sitronix Technology Corporation +smsc Standard Microsystems Corporation +snps Synopsys, Inc. +solidrun SolidRun +sony Sony Corporation +spansion Spansion Inc. st STMicroelectronics ste ST-Ericsson stericsson ST-Ericsson +synology Synology, Inc. +tbs TBS Technologies +thine THine Electronics, Inc. ti Texas Instruments tlm Trusted Logic Mobility +toradex Toradex AG toshiba Toshiba Corporation toumaz Toumaz +usi Universal Scientific Industrial Co., Ltd. v3 V3 Semiconductor +variscite Variscite Ltd. via VIA Technologies, Inc. +voipac Voipac Technologies s.r.o. winbond Winbond Electronics corp. wlf Wolfson Microelectronics wm Wondermedia Technologies, Inc. +xes Extreme Engineering Solutions (X-ES) +xillybus Xillybus Ltd. xlnx Xilinx +zyxel ZyXEL Communications Corp. +zarlink Zarlink Semiconductor diff --git a/Documentation/devicetree/bindings/video/adi,adv7123.txt b/Documentation/devicetree/bindings/video/adi,adv7123.txt new file mode 100644 index 000000000000..a6b2b2b8f3d9 --- /dev/null +++ b/Documentation/devicetree/bindings/video/adi,adv7123.txt @@ -0,0 +1,50 @@ +Analog Device ADV7123 Video DAC +------------------------------- + +The ADV7123 is a digital-to-analog converter that outputs VGA signals from a +parallel video input. + +Required properties: + +- compatible: Should be "adi,adv7123" + +Optional properties: + +- psave-gpios: Power save control GPIO + +Required nodes: + +The ADV7123 has two video ports. Their connections are modeled using the OF +graph bindings specified in Documentation/devicetree/bindings/graph.txt. + +- Video port 0 for DPI input +- Video port 1 for VGA output + + +Example +------- + + adv7123: encoder@0 { + compatible = "adi,adv7123"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + adv7123_in: endpoint@0 { + remote-endpoint = <&dpi_out>; + }; + }; + + port@1 { + reg = <1>; + + adv7123_out: endpoint@0 { + remote-endpoint = <&vga_connector_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/video/analog-tv-connector.txt b/Documentation/devicetree/bindings/video/analog-tv-connector.txt new file mode 100644 index 000000000000..0c0970c210ab --- /dev/null +++ b/Documentation/devicetree/bindings/video/analog-tv-connector.txt @@ -0,0 +1,25 @@ +Analog TV Connector +=================== + +Required properties: +- compatible: "composite-video-connector" or "svideo-connector" + +Optional properties: +- label: a symbolic name for the connector + +Required nodes: +- Video port for TV input + +Example +------- + +tv: connector { + compatible = "composite-video-connector"; + label = "tv"; + + port { + tv_connector_in: endpoint { + remote-endpoint = <&venc_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/video/arm,pl11x.txt b/Documentation/devicetree/bindings/video/arm,pl11x.txt new file mode 100644 index 000000000000..3e3039a8a253 --- /dev/null +++ b/Documentation/devicetree/bindings/video/arm,pl11x.txt @@ -0,0 +1,109 @@ +* ARM PrimeCell Color LCD Controller PL110/PL111 + +See also Documentation/devicetree/bindings/arm/primecell.txt + +Required properties: + +- compatible: must be one of: + "arm,pl110", "arm,primecell" + "arm,pl111", "arm,primecell" + +- reg: base address and size of the control registers block + +- interrupt-names: either the single entry "combined" representing a + combined interrupt output (CLCDINTR), or the four entries + "mbe", "vcomp", "lnbu", "fuf" representing the individual + CLCDMBEINTR, CLCDVCOMPINTR, CLCDLNBUINTR, CLCDFUFINTR interrupts + +- interrupts: contains an interrupt specifier for each entry in + interrupt-names + +- clock-names: should contain "clcdclk" and "apb_pclk" + +- clocks: contains phandle and clock specifier pairs for the entries + in the clock-names property. See + Documentation/devicetree/binding/clock/clock-bindings.txt + +Optional properties: + +- memory-region: phandle to a node describing memory (see + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt) + to be used for the framebuffer; if not present, the framebuffer + may be located anywhere in the memory + +- max-memory-bandwidth: maximum bandwidth in bytes per second that the + cell's memory interface can handle; if not present, the memory + interface is fast enough to handle all possible video modes + +Required sub-nodes: + +- port: describes LCD panel signals, following the common binding + for video transmitter interfaces; see + Documentation/devicetree/bindings/media/video-interfaces.txt; + when it is a TFT panel, the port's endpoint must define the + following property: + + - arm,pl11x,tft-r0g0b0-pads: an array of three 32-bit values, + defining the way CLD pads are wired up; first value + contains index of the "CLD" external pin (pad) used + as R0 (first bit of the red component), second value + index of the pad used as G0, third value index of the + pad used as B0, see also "LCD panel signal multiplexing + details" paragraphs in the PL110/PL111 Technical + Reference Manuals; this implicitly defines available + color modes, for example: + - PL111 TFT 4:4:4 panel: + arm,pl11x,tft-r0g0b0-pads = <4 15 20>; + - PL110 TFT (1:)5:5:5 panel: + arm,pl11x,tft-r0g0b0-pads = <1 7 13>; + - PL111 TFT (1:)5:5:5 panel: + arm,pl11x,tft-r0g0b0-pads = <3 11 19>; + - PL111 TFT 5:6:5 panel: + arm,pl11x,tft-r0g0b0-pads = <3 10 19>; + - PL110 and PL111 TFT 8:8:8 panel: + arm,pl11x,tft-r0g0b0-pads = <0 8 16>; + - PL110 and PL111 TFT 8:8:8 panel, R & B components swapped: + arm,pl11x,tft-r0g0b0-pads = <16 8 0>; + + +Example: + + clcd@10020000 { + compatible = "arm,pl111", "arm,primecell"; + reg = <0x10020000 0x1000>; + interrupt-names = "combined"; + interrupts = <0 44 4>; + clocks = <&oscclk1>, <&oscclk2>; + clock-names = "clcdclk", "apb_pclk"; + max-memory-bandwidth = <94371840>; /* Bps, 1024x768@60 16bpp */ + + port { + clcd_pads: endpoint { + remote-endpoint = <&clcd_panel>; + arm,pl11x,tft-r0g0b0-pads = <0 8 16>; + }; + }; + + }; + + panel { + compatible = "panel-dpi"; + + port { + clcd_panel: endpoint { + remote-endpoint = <&clcd_pads>; + }; + }; + + panel-timing { + clock-frequency = <25175000>; + hactive = <640>; + hback-porch = <40>; + hfront-porch = <24>; + hsync-len = <96>; + vactive = <480>; + vback-porch = <32>; + vfront-porch = <11>; + vsync-len = <2>; + }; + }; diff --git a/Documentation/devicetree/bindings/video/atmel,lcdc.txt b/Documentation/devicetree/bindings/video/atmel,lcdc.txt index 1ec175eddca8..f059dd0b3d28 100644 --- a/Documentation/devicetree/bindings/video/atmel,lcdc.txt +++ b/Documentation/devicetree/bindings/video/atmel,lcdc.txt @@ -20,6 +20,9 @@ Required nodes: - default-mode: a videomode within the display with timing parameters as specified below. +Optional properties: +- lcd-supply: Regulator for LCD supply voltage. + Example: fb0: fb@0x00500000 { @@ -39,13 +42,14 @@ Atmel LCDC Display ----------------------------------------------------- Required properties (as per of_videomode_helper): - - atmel,dmacon: dma controler configuration - - atmel,lcdcon2: lcd controler configuration + - atmel,dmacon: dma controller configuration + - atmel,lcdcon2: lcd controller configuration - atmel,guard-time: lcd guard time (Delay in frame periods) - bits-per-pixel: lcd panel bit-depth. Optional properties (as per of_videomode_helper): - atmel,lcdcon-backlight: enable backlight + - atmel,lcdcon-backlight-inverted: invert backlight PWM polarity - atmel,lcd-wiring-mode: lcd wiring mode "RGB" or "BRG" - atmel,power-control-gpio: gpio to power on or off the LCD (as many as needed) diff --git a/Documentation/devicetree/bindings/video/backlight/gpio-backlight.txt b/Documentation/devicetree/bindings/video/backlight/gpio-backlight.txt new file mode 100644 index 000000000000..321be6640533 --- /dev/null +++ b/Documentation/devicetree/bindings/video/backlight/gpio-backlight.txt @@ -0,0 +1,16 @@ +gpio-backlight bindings + +Required properties: + - compatible: "gpio-backlight" + - gpios: describes the gpio that is used for enabling/disabling the backlight. + refer to bindings/gpio/gpio.txt for more details. + +Optional properties: + - default-on: enable the backlight at boot. + +Example: + backlight { + compatible = "gpio-backlight"; + gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>; + default-on; + }; diff --git a/Documentation/devicetree/bindings/video/cirrus,clps711x-fb.txt b/Documentation/devicetree/bindings/video/cirrus,clps711x-fb.txt new file mode 100644 index 000000000000..6fc3c6adeefa --- /dev/null +++ b/Documentation/devicetree/bindings/video/cirrus,clps711x-fb.txt @@ -0,0 +1,47 @@ +* Currus Logic CLPS711X Framebuffer + +Required properties: +- compatible: Shall contain "cirrus,clps711x-fb". +- reg : Physical base address and length of the controller's registers + + location and size of the framebuffer memory. +- clocks : phandle + clock specifier pair of the FB reference clock. +- display : phandle to a display node as described in + Documentation/devicetree/bindings/video/display-timing.txt. + Additionally, the display node has to define properties: + - bits-per-pixel: Bits per pixel. + - ac-prescale : LCD AC bias frequency. This frequency is the required + AC bias frequency for a given manufacturer's LCD plate. + - cmap-invert : Invert the color levels (Optional). + +Optional properties: +- lcd-supply: Regulator for LCD supply voltage. + +Example: + fb: fb@800002c0 { + compatible = "cirrus,ep7312-fb", "cirrus,clps711x-fb"; + reg = <0x800002c0 0xd44>, <0x60000000 0xc000>; + clocks = <&clks 2>; + lcd-supply = <®5v0>; + display = <&display>; + }; + + display: display { + model = "320x240x4"; + native-mode = <&timing0>; + bits-per-pixel = <4>; + ac-prescale = <17>; + + display-timings { + timing0: 320x240 { + hactive = <320>; + hback-porch = <0>; + hfront-porch = <0>; + hsync-len = <0>; + vactive = <240>; + vback-porch = <0>; + vfront-porch = <0>; + vsync-len = <0>; + clock-frequency = <6500000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/video/dvi-connector.txt b/Documentation/devicetree/bindings/video/dvi-connector.txt new file mode 100644 index 000000000000..fc53f7c60bc6 --- /dev/null +++ b/Documentation/devicetree/bindings/video/dvi-connector.txt @@ -0,0 +1,35 @@ +DVI Connector +============== + +Required properties: +- compatible: "dvi-connector" + +Optional properties: +- label: a symbolic name for the connector +- ddc-i2c-bus: phandle to the i2c bus that is connected to DVI DDC +- analog: the connector has DVI analog pins +- digital: the connector has DVI digital pins +- dual-link: the connector has pins for DVI dual-link + +Required nodes: +- Video port for DVI input + +Note: One (or both) of 'analog' or 'digital' must be set. + +Example +------- + +dvi0: connector@0 { + compatible = "dvi-connector"; + label = "dvi"; + + digital; + + ddc-i2c-bus = <&i2c3>; + + port { + dvi_connector_in: endpoint { + remote-endpoint = <&tfp410_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/video/exynos_dp.txt b/Documentation/devicetree/bindings/video/exynos_dp.txt index 3289d76a21d0..53dbccfa80ca 100644 --- a/Documentation/devicetree/bindings/video/exynos_dp.txt +++ b/Documentation/devicetree/bindings/video/exynos_dp.txt @@ -49,6 +49,8 @@ Required properties for dp-controller: -samsung,lane-count: number of lanes supported by the panel. LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4 + - display-timings: timings for the connected panel as described by + Documentation/devicetree/bindings/video/display-timing.txt Optional properties for dp-controller: -interlaced: @@ -60,6 +62,10 @@ Optional properties for dp-controller: -hsync-active-high: HSYNC polarity configuration. High if defined, Low if not defined + -samsung,hpd-gpio: + Hotplug detect GPIO. + Indicates which GPIO should be used for hotplug + detection Example: @@ -84,4 +90,19 @@ Board Specific portion: samsung,color-depth = <1>; samsung,link-rate = <0x0a>; samsung,lane-count = <4>; + + display-timings { + native-mode = <&lcd_timing>; + lcd_timing: 1366x768 { + clock-frequency = <70589280>; + hactive = <1366>; + vactive = <768>; + hfront-porch = <40>; + hback-porch = <40>; + hsync-len = <32>; + vback-porch = <10>; + vfront-porch = <12>; + vsync-len = <6>; + }; + }; }; diff --git a/Documentation/devicetree/bindings/video/exynos_dsim.txt b/Documentation/devicetree/bindings/video/exynos_dsim.txt new file mode 100644 index 000000000000..e74243b4b317 --- /dev/null +++ b/Documentation/devicetree/bindings/video/exynos_dsim.txt @@ -0,0 +1,83 @@ +Exynos MIPI DSI Master + +Required properties: + - compatible: value should be one of the following + "samsung,exynos3250-mipi-dsi" /* for Exynos3250/3472 SoCs */ + "samsung,exynos4210-mipi-dsi" /* for Exynos4 SoCs */ + "samsung,exynos5410-mipi-dsi" /* for Exynos5410/5420/5440 SoCs */ + - reg: physical base address and length of the registers set for the device + - interrupts: should contain DSI interrupt + - clocks: list of clock specifiers, must contain an entry for each required + entry in clock-names + - clock-names: should include "bus_clk"and "pll_clk" entries + - phys: list of phy specifiers, must contain an entry for each required + entry in phy-names + - phy-names: should include "dsim" entry + - vddcore-supply: MIPI DSIM Core voltage supply (e.g. 1.1V) + - vddio-supply: MIPI DSIM I/O and PLL voltage supply (e.g. 1.8V) + - samsung,pll-clock-frequency: specifies frequency of the "pll_clk" clock + - #address-cells, #size-cells: should be set respectively to <1> and <0> + according to DSI host bindings (see MIPI DSI bindings [1]) + +Optional properties: + - samsung,power-domain: a phandle to DSIM power domain node + +Child nodes: + Should contain DSI peripheral nodes (see MIPI DSI bindings [1]). + +Video interfaces: + Device node can contain video interface port nodes according to [2]. + The following are properties specific to those nodes: + + port node: + - reg: (required) can be 0 for input RGB/I80 port or 1 for DSI port; + + endpoint node of DSI port (reg = 1): + - samsung,burst-clock-frequency: specifies DSI frequency in high-speed burst + mode + - samsung,esc-clock-frequency: specifies DSI frequency in escape mode + +[1]: Documentation/devicetree/bindings/mipi/dsi/mipi-dsi-bus.txt +[2]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + + dsi@11C80000 { + compatible = "samsung,exynos4210-mipi-dsi"; + reg = <0x11C80000 0x10000>; + interrupts = <0 79 0>; + clocks = <&clock 286>, <&clock 143>; + clock-names = "bus_clk", "pll_clk"; + phys = <&mipi_phy 1>; + phy-names = "dsim"; + vddcore-supply = <&vusb_reg>; + vddio-supply = <&vmipi_reg>; + samsung,power-domain = <&pd_lcd0>; + #address-cells = <1>; + #size-cells = <0>; + samsung,pll-clock-frequency = <24000000>; + + panel@1 { + reg = <0>; + ... + port { + panel_ep: endpoint { + remote-endpoint = <&dsi_ep>; + }; + }; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + dsi_ep: endpoint { + reg = <0>; + samsung,burst-clock-frequency = <500000000>; + samsung,esc-clock-frequency = <20000000>; + remote-endpoint = <&panel_ep>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/video/exynos_hdmi.txt b/Documentation/devicetree/bindings/video/exynos_hdmi.txt index 50decf8e1b90..1fd8cf9cbfac 100644 --- a/Documentation/devicetree/bindings/video/exynos_hdmi.txt +++ b/Documentation/devicetree/bindings/video/exynos_hdmi.txt @@ -5,6 +5,7 @@ Required properties: 1) "samsung,exynos5-hdmi" <DEPRECATED> 2) "samsung,exynos4210-hdmi" 3) "samsung,exynos4212-hdmi" + 4) "samsung,exynos5420-hdmi" - reg: physical base address of the hdmi and length of memory mapped region. - interrupts: interrupt number to the cpu. @@ -25,6 +26,10 @@ Required properties: sclk_pixel. - clock-names: aliases as per driver requirements for above clock IDs: "hdmi", "sclk_hdmi", "sclk_pixel", "sclk_hdmiphy" and "mout_hdmi". +- ddc: phandle to the hdmi ddc node +- phy: phandle to the hdmi phy node +- samsung,syscon-phandle: phandle for system controller node for PMU. + Example: hdmi { @@ -32,4 +37,7 @@ Example: reg = <0x14530000 0x100000>; interrupts = <0 95 0>; hpd-gpio = <&gpx3 7 1>; + ddc = <&hdmi_ddc_node>; + phy = <&hdmi_phy_node>; + samsung,syscon-phandle = <&pmu_system_controller>; }; diff --git a/Documentation/devicetree/bindings/video/exynos_mixer.txt b/Documentation/devicetree/bindings/video/exynos_mixer.txt index 7bfde9c9d658..08b394b1edbf 100644 --- a/Documentation/devicetree/bindings/video/exynos_mixer.txt +++ b/Documentation/devicetree/bindings/video/exynos_mixer.txt @@ -4,8 +4,9 @@ Required properties: - compatible: value should be one of the following: 1) "samsung,exynos5-mixer" <DEPRECATED> 2) "samsung,exynos4210-mixer" - 3) "samsung,exynos5250-mixer" - 4) "samsung,exynos5420-mixer" + 3) "samsung,exynos4212-mixer" + 4) "samsung,exynos5250-mixer" + 5) "samsung,exynos5420-mixer" - reg: physical base address of the mixer and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/video/fsl,imx-fb.txt b/Documentation/devicetree/bindings/video/fsl,imx-fb.txt index 46da08db186a..8c8c2f4e4c3f 100644 --- a/Documentation/devicetree/bindings/video/fsl,imx-fb.txt +++ b/Documentation/devicetree/bindings/video/fsl,imx-fb.txt @@ -15,8 +15,12 @@ Required nodes: - fsl,pcr: LCDC PCR value Optional properties: +- lcd-supply: Regulator for LCD supply voltage. - fsl,dmacr: DMA Control Register value. This is optional. By default, the register is not modified as recommended by the datasheet. +- fsl,lpccr: Contrast Control Register value. This property provides the + default value for the contrast control register. + If that property is omitted, the register is zeroed. - fsl,lscr1: LCDC Sharp Configuration Register value. Example: diff --git a/Documentation/devicetree/bindings/video/hdmi-connector.txt b/Documentation/devicetree/bindings/video/hdmi-connector.txt new file mode 100644 index 000000000000..acd5668b1ce1 --- /dev/null +++ b/Documentation/devicetree/bindings/video/hdmi-connector.txt @@ -0,0 +1,29 @@ +HDMI Connector +============== + +Required properties: +- compatible: "hdmi-connector" +- type: the HDMI connector type: "a", "b", "c", "d" or "e" + +Optional properties: +- label: a symbolic name for the connector +- hpd-gpios: HPD GPIO number + +Required nodes: +- Video port for HDMI input + +Example +------- + +hdmi0: connector@1 { + compatible = "hdmi-connector"; + label = "hdmi"; + + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&tpd12s015_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/video/lgphilips,lb035q02.txt b/Documentation/devicetree/bindings/video/lgphilips,lb035q02.txt new file mode 100644 index 000000000000..1a1e653e5407 --- /dev/null +++ b/Documentation/devicetree/bindings/video/lgphilips,lb035q02.txt @@ -0,0 +1,33 @@ +LG.Philips LB035Q02 Panel +========================= + +Required properties: +- compatible: "lgphilips,lb035q02" +- enable-gpios: panel enable gpio + +Optional properties: +- label: a symbolic name for the panel + +Required nodes: +- Video port for DPI input + +Example +------- + +lcd-panel: panel@0 { + compatible = "lgphilips,lb035q02"; + reg = <0>; + spi-max-frequency = <100000>; + spi-cpol; + spi-cpha; + + label = "lcd"; + + enable-gpios = <&gpio7 7 0>; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/video/panel-dpi.txt b/Documentation/devicetree/bindings/video/panel-dpi.txt new file mode 100644 index 000000000000..a40180b05bab --- /dev/null +++ b/Documentation/devicetree/bindings/video/panel-dpi.txt @@ -0,0 +1,45 @@ +Generic MIPI DPI Panel +====================== + +Required properties: +- compatible: "panel-dpi" + +Optional properties: +- label: a symbolic name for the panel +- enable-gpios: panel enable gpio + +Required nodes: +- "panel-timing" containing video timings + (Documentation/devicetree/bindings/video/display-timing.txt) +- Video port for DPI input + +Example +------- + +lcd0: display@0 { + compatible = "samsung,lte430wq-f0c", "panel-dpi"; + label = "lcd"; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + + panel-timing { + clock-frequency = <9200000>; + hactive = <480>; + vactive = <272>; + hfront-porch = <8>; + hback-porch = <4>; + hsync-len = <41>; + vback-porch = <2>; + vfront-porch = <4>; + vsync-len = <10>; + + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/video/panel-dsi-cm.txt b/Documentation/devicetree/bindings/video/panel-dsi-cm.txt new file mode 100644 index 000000000000..dce48eb9db57 --- /dev/null +++ b/Documentation/devicetree/bindings/video/panel-dsi-cm.txt @@ -0,0 +1,29 @@ +Generic MIPI DSI Command Mode Panel +=================================== + +Required properties: +- compatible: "panel-dsi-cm" + +Optional properties: +- label: a symbolic name for the panel +- reset-gpios: panel reset gpio +- te-gpios: panel TE gpio + +Required nodes: +- Video port for DSI input + +Example +------- + +lcd0: display { + compatible = "tpo,taal", "panel-dsi-cm"; + label = "lcd0"; + + reset-gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; + + port { + lcd0_in: endpoint { + remote-endpoint = <&dsi1_out_ep>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/video/renesas,du.txt b/Documentation/devicetree/bindings/video/renesas,du.txt new file mode 100644 index 000000000000..5102830f2760 --- /dev/null +++ b/Documentation/devicetree/bindings/video/renesas,du.txt @@ -0,0 +1,84 @@ +* Renesas R-Car Display Unit (DU) + +Required Properties: + + - compatible: must be one of the following. + - "renesas,du-r8a7779" for R8A7779 (R-Car H1) compatible DU + - "renesas,du-r8a7790" for R8A7790 (R-Car H2) compatible DU + - "renesas,du-r8a7791" for R8A7791 (R-Car M2) compatible DU + + - reg: A list of base address and length of each memory resource, one for + each entry in the reg-names property. + - reg-names: Name of the memory resources. The DU requires one memory + resource for the DU core (named "du") and one memory resource for each + LVDS encoder (named "lvds.x" with "x" being the LVDS controller numerical + index). + + - interrupt-parent: phandle of the parent interrupt controller. + - interrupts: Interrupt specifiers for the DU interrupts. + + - clocks: A list of phandles + clock-specifier pairs, one for each entry in + the clock-names property. + - clock-names: Name of the clocks. This property is model-dependent. + - R8A7779 uses a single functional clock. The clock doesn't need to be + named. + - R8A7790 and R8A7791 use one functional clock per channel and one clock + per LVDS encoder. The functional clocks must be named "du.x" with "x" + being the channel numerical index. The LVDS clocks must be named + "lvds.x" with "x" being the LVDS encoder numerical index. + +Required nodes: + +The connections to the DU output video ports are modeled using the OF graph +bindings specified in Documentation/devicetree/bindings/graph.txt. + +The following table lists for each supported model the port number +corresponding to each DU output. + + Port 0 Port1 Port2 +----------------------------------------------------------------------------- + R8A7779 (H1) DPAD 0 DPAD 1 - + R8A7790 (H2) DPAD LVDS 0 LVDS 1 + R8A7791 (M2) DPAD LVDS 0 - + + +Example: R8A7790 (R-Car H2) DU + + du: du@feb00000 { + compatible = "renesas,du-r8a7790"; + reg = <0 0xfeb00000 0 0x70000>, + <0 0xfeb90000 0 0x1c>, + <0 0xfeb94000 0 0x1c>; + reg-names = "du", "lvds.0", "lvds.1"; + interrupt-parent = <&gic>; + interrupts = <0 256 IRQ_TYPE_LEVEL_HIGH>, + <0 268 IRQ_TYPE_LEVEL_HIGH>, + <0 269 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7790_CLK_DU0>, + <&mstp7_clks R8A7790_CLK_DU1>, + <&mstp7_clks R8A7790_CLK_DU2>, + <&mstp7_clks R8A7790_CLK_LVDS0>, + <&mstp7_clks R8A7790_CLK_LVDS1>; + clock-names = "du.0", "du.1", "du.2", "lvds.0", "lvds.1"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + du_out_rgb: endpoint { + }; + }; + port@1 { + reg = <1>; + du_out_lvds0: endpoint { + }; + }; + port@2 { + reg = <2>; + du_out_lvds1: endpoint { + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/video/samsung-fimd.txt b/Documentation/devicetree/bindings/video/samsung-fimd.txt index 778838a0336a..4e6c77c85546 100644 --- a/Documentation/devicetree/bindings/video/samsung-fimd.txt +++ b/Documentation/devicetree/bindings/video/samsung-fimd.txt @@ -8,9 +8,8 @@ Required properties: - compatible: value should be one of the following "samsung,s3c2443-fimd"; /* for S3C24XX SoCs */ "samsung,s3c6400-fimd"; /* for S3C64XX SoCs */ - "samsung,s5p6440-fimd"; /* for S5P64X0 SoCs */ - "samsung,s5pc100-fimd"; /* for S5PC100 SoC */ "samsung,s5pv210-fimd"; /* for S5PV210 SoC */ + "samsung,exynos3250-fimd"; /* for Exynos3250/3472 SoCs */ "samsung,exynos4210-fimd"; /* for Exynos4 SoCs */ "samsung,exynos5250-fimd"; /* for Exynos5 SoCs */ @@ -39,6 +38,51 @@ Required properties: Optional Properties: - samsung,power-domain: a phandle to FIMD power domain node. +- samsung,invert-vden: video enable signal is inverted +- samsung,invert-vclk: video clock signal is inverted +- display-timings: timing settings for FIMD, as described in document [1]. + Can be used in case timings cannot be provided otherwise + or to override timings provided by the panel. +- samsung,sysreg: handle to syscon used to control the system registers +- i80-if-timings: timing configuration for lcd i80 interface support. + - cs-setup: clock cycles for the active period of address signal is enabled + until chip select is enabled. + If not specified, the default value(0) will be used. + - wr-setup: clock cycles for the active period of CS signal is enabled until + write signal is enabled. + If not specified, the default value(0) will be used. + - wr-active: clock cycles for the active period of CS is enabled. + If not specified, the default value(1) will be used. + - wr-hold: clock cycles for the active period of CS is disabled until write + signal is disabled. + If not specified, the default value(0) will be used. + + The parameters are defined as: + + VCLK(internal) __|??????|_____|??????|_____|??????|_____|??????|_____|?? + : : : : : + Address Output --:<XXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XX + | cs-setup+1 | : : : + |<---------->| : : : + Chip Select ???????????????|____________:____________:____________|?? + | wr-setup+1 | | wr-hold+1 | + |<---------->| |<---------->| + Write Enable ????????????????????????????|____________|??????????????? + | wr-active+1| + |<---------->| + Video Data ----------------------------<XXXXXXXXXXXXXXXXXXXXXXXXX>-- + +The device node can contain 'port' child nodes according to the bindings defined +in [2]. The following are properties specific to those nodes: +- reg: (required) port index, can be: + 0 - for CAMIF0 input, + 1 - for CAMIF1 input, + 2 - for CAMIF2 input, + 3 - for parallel output, + 4 - for write-back interface + +[1]: Documentation/devicetree/bindings/video/display-timing.txt +[2]: Documentation/devicetree/bindings/media/video-interfaces.txt Example: diff --git a/Documentation/devicetree/bindings/video/sharp,ls037v7dw01.txt b/Documentation/devicetree/bindings/video/sharp,ls037v7dw01.txt new file mode 100644 index 000000000000..0cc8981e9d49 --- /dev/null +++ b/Documentation/devicetree/bindings/video/sharp,ls037v7dw01.txt @@ -0,0 +1,43 @@ +SHARP LS037V7DW01 TFT-LCD panel +=================================== + +Required properties: +- compatible: "sharp,ls037v7dw01" + +Optional properties: +- label: a symbolic name for the panel +- enable-gpios: a GPIO spec for the optional enable pin. + This pin is the INI pin as specified in the LS037V7DW01.pdf file. +- reset-gpios: a GPIO spec for the optional reset pin. + This pin is the RESB pin as specified in the LS037V7DW01.pdf file. +- mode-gpios: a GPIO + ordered MO, LR, and UD as specified in the LS037V7DW01.pdf file. + +Required nodes: +- Video port for DPI input + +This panel can have zero to five GPIOs to configure to change configuration +between QVGA and VGA mode and the scan direction. As these pins can be also +configured with external pulls, all the GPIOs are considered optional with holes +in the array. + +Example +------- + +Example when connected to a omap2+ based device: + +lcd0: display { + compatible = "sharp,ls037v7dw01"; + power-supply = <&lcd_3v3>; + enable-gpios = <&gpio5 24 GPIO_ACTIVE_HIGH>; /* gpio152, lcd INI */ + reset-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd RESB */ + mode-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH /* gpio154, lcd MO */ + &gpio1 2 GPIO_ACTIVE_HIGH /* gpio2, lcd LR */ + &gpio1 3 GPIO_ACTIVE_HIGH>; /* gpio3, lcd UD */ + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/video/sony,acx565akm.txt b/Documentation/devicetree/bindings/video/sony,acx565akm.txt new file mode 100644 index 000000000000..e12333280749 --- /dev/null +++ b/Documentation/devicetree/bindings/video/sony,acx565akm.txt @@ -0,0 +1,30 @@ +Sony ACX565AKM SDI Panel +======================== + +Required properties: +- compatible: "sony,acx565akm" + +Optional properties: +- label: a symbolic name for the panel +- reset-gpios: panel reset gpio + +Required nodes: +- Video port for SDI input + +Example +------- + +acx565akm@2 { + compatible = "sony,acx565akm"; + spi-max-frequency = <6000000>; + reg = <2>; + + label = "lcd"; + reset-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* 90 */ + + port { + lcd_in: endpoint { + remote-endpoint = <&sdi_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/video/thine,thc63lvdm83d b/Documentation/devicetree/bindings/video/thine,thc63lvdm83d new file mode 100644 index 000000000000..527e236e9a2a --- /dev/null +++ b/Documentation/devicetree/bindings/video/thine,thc63lvdm83d @@ -0,0 +1,50 @@ +THine Electronics THC63LVDM83D LVDS serializer +---------------------------------------------- + +The THC63LVDM83D is an LVDS serializer designed to support pixel data +transmission between a host and a flat panel. + +Required properties: + +- compatible: Should be "thine,thc63lvdm83d" + +Optional properties: + +- pwdn-gpios: Power down control GPIO + +Required nodes: + +The THC63LVDM83D has two video ports. Their connections are modeled using the +OFgraph bindings specified in Documentation/devicetree/bindings/graph.txt. + +- Video port 0 for CMOS/TTL input +- Video port 1 for LVDS output + + +Example +------- + + lvds_enc: encoder@0 { + compatible = "thine,thc63lvdm83d"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + lvds_enc_in: endpoint@0 { + remote-endpoint = <&rgb_out>; + }; + }; + + port@1 { + reg = <1>; + + lvds_enc_out: endpoint@0 { + remote-endpoint = <&panel_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/video/ti,omap-dss.txt b/Documentation/devicetree/bindings/video/ti,omap-dss.txt new file mode 100644 index 000000000000..d5f1a3fe3109 --- /dev/null +++ b/Documentation/devicetree/bindings/video/ti,omap-dss.txt @@ -0,0 +1,211 @@ +Texas Instruments OMAP Display Subsystem +======================================== + +Generic Description +------------------- + +This document is a generic description of the OMAP Display Subsystem bindings. +Binding details for each OMAP SoC version are described in respective binding +documentation. + +The OMAP Display Subsystem (DSS) hardware consists of DSS Core, DISPC module and +a number of encoder modules. All DSS versions contain DSS Core and DISPC, but +the encoder modules vary. + +The DSS Core is the parent of the other DSS modules, and manages clock routing, +integration to the SoC, etc. + +DISPC is the display controller, which reads pixels from the memory and outputs +a RGB pixel stream to encoders. + +The encoder modules encode the received RGB pixel stream to a video output like +HDMI, MIPI DPI, etc. + +Video Ports +----------- + +The DSS Core and the encoders have video port outputs. The structure of the +video ports is described in Documentation/devicetree/bindings/video/video- +ports.txt, and the properties for the ports and endpoints for each encoder are +described in the SoC's DSS binding documentation. + +The video ports are used to describe the connections to external hardware, like +panels or external encoders. + +Aliases +------- + +The board dts file may define aliases for displays to assign "displayX" style +name for each display. If no aliases are defined, a semi-random number is used +for the display. + +Example +------- + +A shortened example of the DSS description for OMAP4, with non-relevant parts +removed, defined in omap4.dtsi: + +dss: dss@58000000 { + compatible = "ti,omap4-dss"; + reg = <0x58000000 0x80>; + status = "disabled"; + ti,hwmods = "dss_core"; + clocks = <&dss_dss_clk>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + dispc@58001000 { + compatible = "ti,omap4-dispc"; + reg = <0x58001000 0x1000>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "dss_dispc"; + clocks = <&dss_dss_clk>; + clock-names = "fck"; + }; + + hdmi: encoder@58006000 { + compatible = "ti,omap4-hdmi"; + reg = <0x58006000 0x200>, + <0x58006200 0x100>, + <0x58006300 0x100>, + <0x58006400 0x1000>; + reg-names = "wp", "pll", "phy", "core"; + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + ti,hwmods = "dss_hdmi"; + clocks = <&dss_48mhz_clk>, <&dss_sys_clk>; + clock-names = "fck", "sys_clk"; + }; +}; + +A shortened example of the board description for OMAP4 Panda board, defined in +omap4-panda.dts. + +The Panda board has a DVI and a HDMI connector, and the board contains a TFP410 +chip (MIPI DPI to DVI encoder) and a TPD12S015 chip (HDMI ESD protection & level +shifter). The video pipelines for the connectors are formed as follows: + +DSS Core --(MIPI DPI)--> TFP410 --(DVI)--> DVI Connector +OMAP HDMI --(HDMI)--> TPD12S015 --(HDMI)--> HDMI Connector + +/ { + aliases { + display0 = &dvi0; + display1 = &hdmi0; + }; + + tfp410: encoder@0 { + compatible = "ti,tfp410"; + gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; /* 0, power-down */ + + pinctrl-names = "default"; + pinctrl-0 = <&tfp410_pins>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + tfp410_in: endpoint@0 { + remote-endpoint = <&dpi_out>; + }; + }; + + port@1 { + reg = <1>; + + tfp410_out: endpoint@0 { + remote-endpoint = <&dvi_connector_in>; + }; + }; + }; + }; + + dvi0: connector@0 { + compatible = "dvi-connector"; + label = "dvi"; + + i2c-bus = <&i2c3>; + + port { + dvi_connector_in: endpoint { + remote-endpoint = <&tfp410_out>; + }; + }; + }; + + tpd12s015: encoder@1 { + compatible = "ti,tpd12s015"; + + pinctrl-names = "default"; + pinctrl-0 = <&tpd12s015_pins>; + + gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */ + <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */ + <&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */ + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + tpd12s015_in: endpoint@0 { + remote-endpoint = <&hdmi_out>; + }; + }; + + port@1 { + reg = <1>; + + tpd12s015_out: endpoint@0 { + remote-endpoint = <&hdmi_connector_in>; + }; + }; + }; + }; + + hdmi0: connector@1 { + compatible = "hdmi-connector"; + label = "hdmi"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&tpd12s015_out>; + }; + }; + }; +}; + +&dss { + status = "ok"; + + pinctrl-names = "default"; + pinctrl-0 = <&dss_dpi_pins>; + + port { + dpi_out: endpoint { + remote-endpoint = <&tfp410_in>; + data-lines = <24>; + }; + }; +}; + +&hdmi { + status = "ok"; + vdda-supply = <&vdac>; + + pinctrl-names = "default"; + pinctrl-0 = <&dss_hdmi_pins>; + + port { + hdmi_out: endpoint { + remote-endpoint = <&tpd12s015_in>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/video/ti,omap2-dss.txt b/Documentation/devicetree/bindings/video/ti,omap2-dss.txt new file mode 100644 index 000000000000..fa8bb2ed1170 --- /dev/null +++ b/Documentation/devicetree/bindings/video/ti,omap2-dss.txt @@ -0,0 +1,54 @@ +Texas Instruments OMAP2 Display Subsystem +========================================= + +See Documentation/devicetree/bindings/video/ti,omap-dss.txt for generic +description about OMAP Display Subsystem bindings. + +DSS Core +-------- + +Required properties: +- compatible: "ti,omap2-dss" +- reg: address and length of the register space +- ti,hwmods: "dss_core" + +Optional nodes: +- Video port for DPI output + +DPI Endpoint required properties: +- data-lines: number of lines used + + +DISPC +----- + +Required properties: +- compatible: "ti,omap2-dispc" +- reg: address and length of the register space +- ti,hwmods: "dss_dispc" +- interrupts: the DISPC interrupt + + +RFBI +---- + +Required properties: +- compatible: "ti,omap2-rfbi" +- reg: address and length of the register space +- ti,hwmods: "dss_rfbi" + + +VENC +---- + +Required properties: +- compatible: "ti,omap2-venc" +- reg: address and length of the register space +- ti,hwmods: "dss_venc" +- vdda-supply: power supply for DAC + +VENC Endpoint required properties: + +Required properties: +- ti,invert-polarity: invert the polarity of the video signal +- ti,channels: 1 for composite, 2 for s-video diff --git a/Documentation/devicetree/bindings/video/ti,omap3-dss.txt b/Documentation/devicetree/bindings/video/ti,omap3-dss.txt new file mode 100644 index 000000000000..0023fa4b1328 --- /dev/null +++ b/Documentation/devicetree/bindings/video/ti,omap3-dss.txt @@ -0,0 +1,83 @@ +Texas Instruments OMAP3 Display Subsystem +========================================= + +See Documentation/devicetree/bindings/video/ti,omap-dss.txt for generic +description about OMAP Display Subsystem bindings. + +DSS Core +-------- + +Required properties: +- compatible: "ti,omap3-dss" +- reg: address and length of the register space +- ti,hwmods: "dss_core" +- clocks: handle to fclk +- clock-names: "fck" + +Optional nodes: +- Video ports: + - Port 0: DPI output + - Port 1: SDI output + +DPI Endpoint required properties: +- data-lines: number of lines used + +SDI Endpoint required properties: +- datapairs: number of datapairs used + + +DISPC +----- + +Required properties: +- compatible: "ti,omap3-dispc" +- reg: address and length of the register space +- ti,hwmods: "dss_dispc" +- interrupts: the DISPC interrupt +- clocks: handle to fclk +- clock-names: "fck" + + +RFBI +---- + +Required properties: +- compatible: "ti,omap3-rfbi" +- reg: address and length of the register space +- ti,hwmods: "dss_rfbi" +- clocks: handles to fclk and iclk +- clock-names: "fck", "ick" + + +VENC +---- + +Required properties: +- compatible: "ti,omap3-venc" +- reg: address and length of the register space +- ti,hwmods: "dss_venc" +- vdda-supply: power supply for DAC +- clocks: handle to fclk +- clock-names: "fck" + +VENC Endpoint required properties: +- ti,invert-polarity: invert the polarity of the video signal +- ti,channels: 1 for composite, 2 for s-video + + +DSI +--- + +Required properties: +- compatible: "ti,omap3-dsi" +- reg: addresses and lengths of the register spaces for 'proto', 'phy' and 'pll' +- reg-names: "proto", "phy", "pll" +- interrupts: the DSI interrupt line +- ti,hwmods: "dss_dsi1" +- vdd-supply: power supply for DSI +- clocks: handles to fclk and pll clock +- clock-names: "fck", "sys_clk" + +DSI Endpoint required properties: +- lanes: list of pin numbers for the DSI lanes: CLK+, CLK-, DATA0+, DATA0-, + DATA1+, DATA1-, ... diff --git a/Documentation/devicetree/bindings/video/ti,omap4-dss.txt b/Documentation/devicetree/bindings/video/ti,omap4-dss.txt new file mode 100644 index 000000000000..b8c29fbd1fbb --- /dev/null +++ b/Documentation/devicetree/bindings/video/ti,omap4-dss.txt @@ -0,0 +1,115 @@ +Texas Instruments OMAP4 Display Subsystem +========================================= + +See Documentation/devicetree/bindings/video/ti,omap-dss.txt for generic +description about OMAP Display Subsystem bindings. + +DSS Core +-------- + +Required properties: +- compatible: "ti,omap4-dss" +- reg: address and length of the register space +- ti,hwmods: "dss_core" +- clocks: handle to fclk +- clock-names: "fck" + +Required nodes: +- DISPC + +Optional nodes: +- DSS Submodules: RFBI, VENC, DSI, HDMI +- Video port for DPI output + +DPI Endpoint required properties: +- data-lines: number of lines used + + +DISPC +----- + +Required properties: +- compatible: "ti,omap4-dispc" +- reg: address and length of the register space +- ti,hwmods: "dss_dispc" +- interrupts: the DISPC interrupt +- clocks: handle to fclk +- clock-names: "fck" + + +RFBI +---- + +Required properties: +- compatible: "ti,omap4-rfbi" +- reg: address and length of the register space +- ti,hwmods: "dss_rfbi" +- clocks: handles to fclk and iclk +- clock-names: "fck", "ick" + +Optional nodes: +- Video port for RFBI output +- RFBI controlled peripherals + + +VENC +---- + +Required properties: +- compatible: "ti,omap4-venc" +- reg: address and length of the register space +- ti,hwmods: "dss_venc" +- vdda-supply: power supply for DAC +- clocks: handle to fclk +- clock-names: "fck" + +Optional nodes: +- Video port for VENC output + +VENC Endpoint required properties: +- ti,invert-polarity: invert the polarity of the video signal +- ti,channels: 1 for composite, 2 for s-video + + +DSI +--- + +Required properties: +- compatible: "ti,omap4-dsi" +- reg: addresses and lengths of the register spaces for 'proto', 'phy' and 'pll' +- reg-names: "proto", "phy", "pll" +- interrupts: the DSI interrupt line +- ti,hwmods: "dss_dsi1" or "dss_dsi2" +- vdd-supply: power supply for DSI +- clocks: handles to fclk and pll clock +- clock-names: "fck", "sys_clk" + +Optional nodes: +- Video port for DSI output +- DSI controlled peripherals + +DSI Endpoint required properties: +- lanes: list of pin numbers for the DSI lanes: CLK+, CLK-, DATA0+, DATA0-, + DATA1+, DATA1-, ... + + +HDMI +---- + +Required properties: +- compatible: "ti,omap4-hdmi" +- reg: addresses and lengths of the register spaces for 'wp', 'pll', 'phy', + 'core' +- reg-names: "wp", "pll", "phy", "core" +- interrupts: the HDMI interrupt line +- ti,hwmods: "dss_hdmi" +- vdda-supply: vdda power supply +- clocks: handles to fclk and pll clock +- clock-names: "fck", "sys_clk" + +Optional nodes: +- Video port for HDMI output + +HDMI Endpoint optional properties: +- lanes: list of 8 pin numbers for the HDMI lanes: CLK+, CLK-, D0+, D0-, + D1+, D1-, D2+, D2-. (default: 0,1,2,3,4,5,6,7) diff --git a/Documentation/devicetree/bindings/video/ti,omap5-dss.txt b/Documentation/devicetree/bindings/video/ti,omap5-dss.txt new file mode 100644 index 000000000000..38ffc8fcd816 --- /dev/null +++ b/Documentation/devicetree/bindings/video/ti,omap5-dss.txt @@ -0,0 +1,96 @@ +Texas Instruments OMAP5 Display Subsystem +========================================= + +See Documentation/devicetree/bindings/video/ti,omap-dss.txt for generic +description about OMAP Display Subsystem bindings. + +DSS Core +-------- + +Required properties: +- compatible: "ti,omap5-dss" +- reg: address and length of the register space +- ti,hwmods: "dss_core" +- clocks: handle to fclk +- clock-names: "fck" + +Required nodes: +- DISPC + +Optional nodes: +- DSS Submodules: RFBI, DSI, HDMI +- Video port for DPI output + +DPI Endpoint required properties: +- data-lines: number of lines used + + +DISPC +----- + +Required properties: +- compatible: "ti,omap5-dispc" +- reg: address and length of the register space +- ti,hwmods: "dss_dispc" +- interrupts: the DISPC interrupt +- clocks: handle to fclk +- clock-names: "fck" + + +RFBI +---- + +Required properties: +- compatible: "ti,omap5-rfbi" +- reg: address and length of the register space +- ti,hwmods: "dss_rfbi" +- clocks: handles to fclk and iclk +- clock-names: "fck", "ick" + +Optional nodes: +- Video port for RFBI output +- RFBI controlled peripherals + + +DSI +--- + +Required properties: +- compatible: "ti,omap5-dsi" +- reg: addresses and lengths of the register spaces for 'proto', 'phy' and 'pll' +- reg-names: "proto", "phy", "pll" +- interrupts: the DSI interrupt line +- ti,hwmods: "dss_dsi1" or "dss_dsi2" +- vdd-supply: power supply for DSI +- clocks: handles to fclk and pll clock +- clock-names: "fck", "sys_clk" + +Optional nodes: +- Video port for DSI output +- DSI controlled peripherals + +DSI Endpoint required properties: +- lanes: list of pin numbers for the DSI lanes: CLK+, CLK-, DATA0+, DATA0-, + DATA1+, DATA1-, ... + + +HDMI +---- + +Required properties: +- compatible: "ti,omap5-hdmi" +- reg: addresses and lengths of the register spaces for 'wp', 'pll', 'phy', + 'core' +- reg-names: "wp", "pll", "phy", "core" +- interrupts: the HDMI interrupt line +- ti,hwmods: "dss_hdmi" +- vdda-supply: vdda power supply +- clocks: handles to fclk and pll clock +- clock-names: "fck", "sys_clk" + +Optional nodes: +- Video port for HDMI output + +HDMI Endpoint optional properties: +- lanes: list of 8 pin numbers for the HDMI lanes: CLK+, CLK-, D0+, D0-, + D1+, D1-, D2+, D2-. (default: 0,1,2,3,4,5,6,7) diff --git a/Documentation/devicetree/bindings/video/ti,tfp410.txt b/Documentation/devicetree/bindings/video/ti,tfp410.txt new file mode 100644 index 000000000000..2cbe32a3d0bb --- /dev/null +++ b/Documentation/devicetree/bindings/video/ti,tfp410.txt @@ -0,0 +1,41 @@ +TFP410 DPI to DVI encoder +========================= + +Required properties: +- compatible: "ti,tfp410" + +Optional properties: +- powerdown-gpios: power-down gpio + +Required nodes: +- Video port 0 for DPI input +- Video port 1 for DVI output + +Example +------- + +tfp410: encoder@0 { + compatible = "ti,tfp410"; + powerdown-gpios = <&twl_gpio 2 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + tfp410_in: endpoint@0 { + remote-endpoint = <&dpi_out>; + }; + }; + + port@1 { + reg = <1>; + + tfp410_out: endpoint@0 { + remote-endpoint = <&dvi_connector_in>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/video/ti,tpd12s015.txt b/Documentation/devicetree/bindings/video/ti,tpd12s015.txt new file mode 100644 index 000000000000..26e6d32e3f20 --- /dev/null +++ b/Documentation/devicetree/bindings/video/ti,tpd12s015.txt @@ -0,0 +1,44 @@ +TPD12S015 HDMI level shifter and ESD protection chip +==================================================== + +Required properties: +- compatible: "ti,tpd12s015" + +Optional properties: +- gpios: CT CP HPD, LS OE and HPD gpios + +Required nodes: +- Video port 0 for HDMI input +- Video port 1 for HDMI output + +Example +------- + +tpd12s015: encoder@1 { + compatible = "ti,tpd12s015"; + + gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */ + <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */ + <&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */ + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + tpd12s015_in: endpoint@0 { + remote-endpoint = <&hdmi_out>; + }; + }; + + port@1 { + reg = <1>; + + tpd12s015_out: endpoint@0 { + remote-endpoint = <&hdmi_connector_in>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/video/toppoly,td028ttec1.txt b/Documentation/devicetree/bindings/video/toppoly,td028ttec1.txt new file mode 100644 index 000000000000..7175dc3740ac --- /dev/null +++ b/Documentation/devicetree/bindings/video/toppoly,td028ttec1.txt @@ -0,0 +1,30 @@ +Toppoly TD028TTEC1 Panel +======================== + +Required properties: +- compatible: "toppoly,td028ttec1" + +Optional properties: +- label: a symbolic name for the panel + +Required nodes: +- Video port for DPI input + +Example +------- + +lcd-panel: td028ttec1@0 { + compatible = "toppoly,td028ttec1"; + reg = <0>; + spi-max-frequency = <100000>; + spi-cpol; + spi-cpha; + + label = "lcd"; + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; +}; + diff --git a/Documentation/devicetree/bindings/video/tpo,td043mtea1.txt b/Documentation/devicetree/bindings/video/tpo,td043mtea1.txt new file mode 100644 index 000000000000..ec6d62975162 --- /dev/null +++ b/Documentation/devicetree/bindings/video/tpo,td043mtea1.txt @@ -0,0 +1,33 @@ +TPO TD043MTEA1 Panel +==================== + +Required properties: +- compatible: "tpo,td043mtea1" +- reset-gpios: panel reset gpio + +Optional properties: +- label: a symbolic name for the panel + +Required nodes: +- Video port for DPI input + +Example +------- + +lcd-panel: panel@0 { + compatible = "tpo,td043mtea1"; + reg = <0>; + spi-max-frequency = <100000>; + spi-cpol; + spi-cpha; + + label = "lcd"; + + reset-gpios = <&gpio7 7 0>; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/video/vga-connector.txt b/Documentation/devicetree/bindings/video/vga-connector.txt new file mode 100644 index 000000000000..c727f298e7ad --- /dev/null +++ b/Documentation/devicetree/bindings/video/vga-connector.txt @@ -0,0 +1,36 @@ +VGA Connector +============= + +Required properties: + +- compatible: "vga-connector" + +Optional properties: + +- label: a symbolic name for the connector corresponding to a hardware label +- ddc-i2c-bus: phandle to the I2C bus that is connected to VGA DDC + +Required nodes: + +The VGA connector internal connections are modeled using the OF graph bindings +specified in Documentation/devicetree/bindings/graph.txt. + +The VGA connector has a single port that must be connected to a video source +port. + + +Example +------- + +vga0: connector@0 { + compatible = "vga-connector"; + label = "vga"; + + ddc-i2c-bus = <&i2c3>; + + port { + vga_connector_in: endpoint { + remote-endpoint = <&adv7123_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/w1/omap-hdq.txt b/Documentation/devicetree/bindings/w1/omap-hdq.txt new file mode 100644 index 000000000000..fef794741bd1 --- /dev/null +++ b/Documentation/devicetree/bindings/w1/omap-hdq.txt @@ -0,0 +1,17 @@ +* OMAP HDQ One wire bus master controller + +Required properties: +- compatible : should be "ti,omap3-1w" +- reg : Address and length of the register set for the device +- interrupts : interrupt line. +- ti,hwmods : "hdq1w" + +Example: + +- From omap3.dtsi + hdqw1w: 1w@480b2000 { + compatible = "ti,omap3-1w"; + reg = <0x480b2000 0x1000>; + interrupts = <58>; + ti,hwmods = "hdq1w"; + }; diff --git a/Documentation/devicetree/bindings/watchdog/cadence-wdt.txt b/Documentation/devicetree/bindings/watchdog/cadence-wdt.txt new file mode 100644 index 000000000000..c3a36ee45552 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/cadence-wdt.txt @@ -0,0 +1,24 @@ +Zynq Watchdog Device Tree Bindings +------------------------------------------- + +Required properties: +- compatible : Should be "cdns,wdt-r1p2". +- clocks : This is pclk (APB clock). +- interrupts : This is wd_irq - watchdog timeout interrupt. +- interrupt-parent : Must be core interrupt controller. + +Optional properties +- reset-on-timeout : If this property exists, then a reset is done + when watchdog times out. +- timeout-sec : Watchdog timeout value (in seconds). + +Example: + watchdog@f8005000 { + compatible = "cdns,wdt-r1p2"; + clocks = <&clkc 45>; + interrupt-parent = <&intc>; + interrupts = <0 9 1>; + reg = <0xf8005000 0x1000>; + reset-on-timeout; + timeout-sec = <10>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt b/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt index 2144af1a5264..8dab6fd024aa 100644 --- a/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt @@ -5,10 +5,16 @@ Required properties: - reg : Should contain WDT registers location and length - interrupts : Should contain WDT interrupt +Optional property: +- big-endian: If present the watchdog device's registers are implemented + in big endian mode, otherwise in native mode(same with CPU), for more + detail please see: Documentation/devicetree/bindings/regmap/regmap.txt. + Examples: wdt@73f98000 { compatible = "fsl,imx51-wdt", "fsl,imx21-wdt"; reg = <0x73f98000 0x4000>; interrupts = <58>; + big-endian; }; diff --git a/Documentation/devicetree/bindings/watchdog/marvel.txt b/Documentation/devicetree/bindings/watchdog/marvel.txt index 5dc8d30061ce..97223fddb7bd 100644 --- a/Documentation/devicetree/bindings/watchdog/marvel.txt +++ b/Documentation/devicetree/bindings/watchdog/marvel.txt @@ -3,17 +3,31 @@ Required Properties: - Compatibility : "marvell,orion-wdt" -- reg : Address of the timer registers + "marvell,armada-370-wdt" + "marvell,armada-xp-wdt" + "marvell,armada-375-wdt" + "marvell,armada-380-wdt" + +- reg : Should contain two entries: first one with the + timer control address, second one with the + rstout enable address. + +For "marvell,armada-375-wdt" and "marvell,armada-380-wdt": + +- reg : A third entry is mandatory and should contain the + shared mask/unmask RSTOUT address. Optional properties: +- interrupts : Contains the IRQ for watchdog expiration - timeout-sec : Contains the watchdog timeout in seconds Example: wdt@20300 { compatible = "marvell,orion-wdt"; - reg = <0x20300 0x28>; + reg = <0x20300 0x28>, <0x20108 0x4>; + interrupts = <3>; timeout-sec = <10>; status = "okay"; }; diff --git a/Documentation/devicetree/bindings/watchdog/meson6-wdt.txt b/Documentation/devicetree/bindings/watchdog/meson6-wdt.txt new file mode 100644 index 000000000000..9200fc2d508c --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/meson6-wdt.txt @@ -0,0 +1,13 @@ +Meson SoCs Watchdog timer + +Required properties: + +- compatible : should be "amlogic,meson6-wdt" +- reg : Specifies base physical address and size of the registers. + +Example: + +wdt: watchdog@c1109900 { + compatible = "amlogic,meson6-wdt"; + reg = <0xc1109900 0x8>; +}; diff --git a/Documentation/devicetree/bindings/watchdog/of-xilinx-wdt.txt b/Documentation/devicetree/bindings/watchdog/of-xilinx-wdt.txt new file mode 100644 index 000000000000..6d63782a7378 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/of-xilinx-wdt.txt @@ -0,0 +1,23 @@ +Xilinx AXI/PLB soft-core watchdog Device Tree Bindings +--------------------------------------------------------- + +Required properties: +- compatible : Should be "xlnx,xps-timebase-wdt-1.00.a" or + "xlnx,xps-timebase-wdt-1.01.a". +- reg : Physical base address and size + +Optional properties: +- clock-frequency : Frequency of clock in Hz +- xlnx,wdt-enable-once : 0 - Watchdog can be restarted + 1 - Watchdog can be enabled just once +- xlnx,wdt-interval : Watchdog timeout interval in 2^<val> clock cycles, + <val> is integer from 8 to 31. + +Example: +axi-timebase-wdt@40100000 { + clock-frequency = <50000000>; + compatible = "xlnx,xps-timebase-wdt-1.00.a"; + reg = <0x40100000 0x10000>; + xlnx,wdt-enable-once = <0x0>; + xlnx,wdt-interval = <0x1b>; +} ; diff --git a/Documentation/devicetree/bindings/watchdog/qcom-wdt.txt b/Documentation/devicetree/bindings/watchdog/qcom-wdt.txt new file mode 100644 index 000000000000..4726924d034e --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/qcom-wdt.txt @@ -0,0 +1,24 @@ +Qualcomm Krait Processor Sub-system (KPSS) Watchdog +--------------------------------------------------- + +Required properties : +- compatible : shall contain only one of the following: + + "qcom,kpss-wdt-msm8960" + "qcom,kpss-wdt-apq8064" + "qcom,kpss-wdt-ipq8064" + +- reg : shall contain base register location and length +- clocks : shall contain the input clock + +Optional properties : +- timeout-sec : shall contain the default watchdog timeout in seconds, + if unset, the default timeout is 30 seconds + +Example: + watchdog@208a038 { + compatible = "qcom,kpss-wdt-ipq8064"; + reg = <0x0208a038 0x40>; + clocks = <&sleep_clk>; + timeout-sec = <10>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt index cfff37511aac..8f3d96af81d7 100644 --- a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt @@ -9,6 +9,7 @@ Required properties: (a) "samsung,s3c2410-wdt" for Exynos4 and previous SoCs (b) "samsung,exynos5250-wdt" for Exynos5250 (c) "samsung,exynos5420-wdt" for Exynos5420 + (c) "samsung,exynos7-wdt" for Exynos7 - reg : base physical address of the controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt b/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt index e39cb266c8f4..b8f75c51453a 100644 --- a/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt @@ -2,13 +2,13 @@ Allwinner SoCs Watchdog timer Required properties: -- compatible : should be "allwinner,<soc-family>-wdt", the currently supported - SoC families being sun4i and sun6i +- compatible : should be either "allwinner,sun4i-a10-wdt" or + "allwinner,sun6i-a31-wdt" - reg : Specifies base physical address and size of the registers. Example: wdt: watchdog@01c20c90 { - compatible = "allwinner,sun4i-wdt"; + compatible = "allwinner,sun4i-a10-wdt"; reg = <0x01c20c90 0x10>; }; diff --git a/Documentation/devicetree/bindings/staging/xillybus.txt b/Documentation/devicetree/bindings/xillybus/xillybus.txt index 9e316dc2e40f..9e316dc2e40f 100644 --- a/Documentation/devicetree/bindings/staging/xillybus.txt +++ b/Documentation/devicetree/bindings/xillybus/xillybus.txt diff --git a/Documentation/devicetree/booting-without-of.txt b/Documentation/devicetree/booting-without-of.txt index 1f013bd0d320..77685185cf3b 100644 --- a/Documentation/devicetree/booting-without-of.txt +++ b/Documentation/devicetree/booting-without-of.txt @@ -51,6 +51,8 @@ Table of Contents VIII - Specifying device power management information (sleep property) + IX - Specifying dma bus information + Appendix A - Sample SOC node for MPC8540 @@ -1332,6 +1334,57 @@ reasonably grouped in this manner, then create a virtual sleep controller (similar to an interrupt nexus, except that defining a standardized sleep-map should wait until its necessity is demonstrated). +IX - Specifying dma bus information + +Some devices may have DMA memory range shifted relatively to the beginning of +RAM, or even placed outside of kernel RAM. For example, the Keystone 2 SoC +worked in LPAE mode with 4G memory has: +- RAM range: [0x8 0000 0000, 0x8 FFFF FFFF] +- DMA range: [ 0x8000 0000, 0xFFFF FFFF] +and DMA range is aliased into first 2G of RAM in HW. + +In such cases, DMA addresses translation should be performed between CPU phys +and DMA addresses. The "dma-ranges" property is intended to be used +for describing the configuration of such system in DT. + +In addition, each DMA master device on the DMA bus may or may not support +coherent DMA operations. The "dma-coherent" property is intended to be used +for identifying devices supported coherent DMA operations in DT. + +* DMA Bus master +Optional property: +- dma-ranges: <prop-encoded-array> encoded as arbitrary number of triplets of + (child-bus-address, parent-bus-address, length). Each triplet specified + describes a contiguous DMA address range. + The dma-ranges property is used to describe the direct memory access (DMA) + structure of a memory-mapped bus whose device tree parent can be accessed + from DMA operations originating from the bus. It provides a means of + defining a mapping or translation between the physical address space of + the bus and the physical address space of the parent of the bus. + (for more information see ePAPR specification) + +* DMA Bus child +Optional property: +- dma-ranges: <empty> value. if present - It means that DMA addresses + translation has to be enabled for this device. +- dma-coherent: Present if dma operations are coherent + +Example: +soc { + compatible = "ti,keystone","simple-bus"; + ranges = <0x0 0x0 0x0 0xc0000000>; + dma-ranges = <0x80000000 0x8 0x00000000 0x80000000>; + + [...] + + usb: usb@2680000 { + compatible = "ti,keystone-dwc3"; + + [...] + dma-coherent; + }; +}; + Appendix A - Sample SOC node for MPC8540 ======================================== diff --git a/Documentation/devicetree/changesets.txt b/Documentation/devicetree/changesets.txt new file mode 100644 index 000000000000..935ba5acc34e --- /dev/null +++ b/Documentation/devicetree/changesets.txt @@ -0,0 +1,40 @@ +A DT changeset is a method which allows one to apply changes +in the live tree in such a way that either the full set of changes +will be applied, or none of them will be. If an error occurs partway +through applying the changeset, then the tree will be rolled back to the +previous state. A changeset can also be removed after it has been +applied. + +When a changeset is applied, all of the changes get applied to the tree +at once before emitting OF_RECONFIG notifiers. This is so that the +receiver sees a complete and consistent state of the tree when it +receives the notifier. + +The sequence of a changeset is as follows. + +1. of_changeset_init() - initializes a changeset + +2. A number of DT tree change calls, of_changeset_attach_node(), +of_changeset_detach_node(), of_changeset_add_property(), +of_changeset_remove_property, of_changeset_update_property() to prepare +a set of changes. No changes to the active tree are made at this point. +All the change operations are recorded in the of_changeset 'entries' +list. + +3. mutex_lock(of_mutex) - starts a changeset; The global of_mutex +ensures there can only be one editor at a time. + +4. of_changeset_apply() - Apply the changes to the tree. Either the +entire changeset will get applied, or if there is an error the tree will +be restored to the previous state + +5. mutex_unlock(of_mutex) - All operations complete, release the mutex + +If a successfully applied changeset needs to be removed, it can be done +with the following sequence. + +1. mutex_lock(of_mutex) + +2. of_changeset_revert() + +3. mutex_unlock(of_mutex) diff --git a/Documentation/devicetree/dynamic-resolution-notes.txt b/Documentation/devicetree/dynamic-resolution-notes.txt new file mode 100644 index 000000000000..083d23262abe --- /dev/null +++ b/Documentation/devicetree/dynamic-resolution-notes.txt @@ -0,0 +1,25 @@ +Device Tree Dynamic Resolver Notes +---------------------------------- + +This document describes the implementation of the in-kernel +Device Tree resolver, residing in drivers/of/resolver.c and is a +companion document to Documentation/devicetree/dt-object-internal.txt[1] + +How the resolver works +---------------------- + +The resolver is given as an input an arbitrary tree compiled with the +proper dtc option and having a /plugin/ tag. This generates the +appropriate __fixups__ & __local_fixups__ nodes as described in [1]. + +In sequence the resolver works by the following steps: + +1. Get the maximum device tree phandle value from the live tree + 1. +2. Adjust all the local phandles of the tree to resolve by that amount. +3. Using the __local__fixups__ node information adjust all local references + by the same amount. +4. For each property in the __fixups__ node locate the node it references + in the live tree. This is the label used to tag the node. +5. Retrieve the phandle of the target of the fixup. +6. For each fixup in the property locate the node:property:offset location + and replace it with the phandle value. diff --git a/Documentation/devicetree/of_selftest.txt b/Documentation/devicetree/of_selftest.txt new file mode 100644 index 000000000000..1e3d5c92b5e3 --- /dev/null +++ b/Documentation/devicetree/of_selftest.txt @@ -0,0 +1,211 @@ +Open Firmware Device Tree Selftest +---------------------------------- + +Author: Gaurav Minocha <gaurav.minocha.os@gmail.com> + +1. Introduction + +This document explains how the test data required for executing OF selftest +is attached to the live tree dynamically, independent of the machine's +architecture. + +It is recommended to read the following documents before moving ahead. + +[1] Documentation/devicetree/usage-model.txt +[2] http://www.devicetree.org/Device_Tree_Usage + +OF Selftest has been designed to test the interface (include/linux/of.h) +provided to device driver developers to fetch the device information..etc. +from the unflattened device tree data structure. This interface is used by +most of the device drivers in various use cases. + + +2. Test-data + +The Device Tree Source file (drivers/of/testcase-data/testcases.dts) contains +the test data required for executing the unit tests automated in +drivers/of/selftests.c. Currently, following Device Tree Source Include files +(.dtsi) are included in testcase.dts: + +drivers/of/testcase-data/tests-interrupts.dtsi +drivers/of/testcase-data/tests-platform.dtsi +drivers/of/testcase-data/tests-phandle.dtsi +drivers/of/testcase-data/tests-match.dtsi + +When the kernel is build with OF_SELFTEST enabled, then the following make rule + +$(obj)/%.dtb: $(src)/%.dts FORCE + $(call if_changed_dep, dtc) + +is used to compile the DT source file (testcase.dts) into a binary blob +(testcase.dtb), also referred as flattened DT. + +After that, using the following rule the binary blob above is wrapped as an +assembly file (testcase.dtb.S). + +$(obj)/%.dtb.S: $(obj)/%.dtb + $(call cmd, dt_S_dtb) + +The assembly file is compiled into an object file (testcase.dtb.o), and is +linked into the kernel image. + + +2.1. Adding the test data + +Un-flattened device tree structure: + +Un-flattened device tree consists of connected device_node(s) in form of a tree +structure described below. + +// following struct members are used to construct the tree +struct device_node { + ... + struct device_node *parent; + struct device_node *child; + struct device_node *sibling; + struct device_node *allnext; /* next in list of all nodes */ + ... + }; + +Figure 1, describes a generic structure of machine's un-flattened device tree +considering only child and sibling pointers. There exists another pointer, +*parent, that is used to traverse the tree in the reverse direction. So, at +a particular level the child node and all the sibling nodes will have a parent +pointer pointing to a common node (e.g. child1, sibling2, sibling3, sibling4's +parent points to root node) + +root ('/') + | +child1 -> sibling2 -> sibling3 -> sibling4 -> null + | | | | + | | | null + | | | + | | child31 -> sibling32 -> null + | | | | + | | null null + | | + | child21 -> sibling22 -> sibling23 -> null + | | | | + | null null null + | +child11 -> sibling12 -> sibling13 -> sibling14 -> null + | | | | + | | | null + | | | + null null child131 -> null + | + null + +Figure 1: Generic structure of un-flattened device tree + + +*allnext: it is used to link all the nodes of DT into a list. So, for the + above tree the list would be as follows: + +root->child1->child11->sibling12->sibling13->child131->sibling14->sibling2-> +child21->sibling22->sibling23->sibling3->child31->sibling32->sibling4->null + +Before executing OF selftest, it is required to attach the test data to +machine's device tree (if present). So, when selftest_data_add() is called, +at first it reads the flattened device tree data linked into the kernel image +via the following kernel symbols: + +__dtb_testcases_begin - address marking the start of test data blob +__dtb_testcases_end - address marking the end of test data blob + +Secondly, it calls of_fdt_unflatten_tree() to unflatten the flattened +blob. And finally, if the machine's device tree (i.e live tree) is present, +then it attaches the unflattened test data tree to the live tree, else it +attaches itself as a live device tree. + +attach_node_and_children() uses of_attach_node() to attach the nodes into the +live tree as explained below. To explain the same, the test data tree described + in Figure 2 is attached to the live tree described in Figure 1. + +root ('/') + | + testcase-data + | + test-child0 -> test-sibling1 -> test-sibling2 -> test-sibling3 -> null + | | | | + test-child01 null null null + + +allnext list: + +root->testcase-data->test-child0->test-child01->test-sibling1->test-sibling2 +->test-sibling3->null + +Figure 2: Example test data tree to be attached to live tree. + +According to the scenario above, the live tree is already present so it isn't +required to attach the root('/') node. All other nodes are attached by calling +of_attach_node() on each node. + +In the function of_attach_node(), the new node is attached as the child of the +given parent in live tree. But, if parent already has a child then the new node +replaces the current child and turns it into its sibling. So, when the testcase +data node is attached to the live tree above (Figure 1), the final structure is + as shown in Figure 3. + +root ('/') + | +testcase-data -> child1 -> sibling2 -> sibling3 -> sibling4 -> null + | | | | | + (...) | | | null + | | child31 -> sibling32 -> null + | | | | + | | null null + | | + | child21 -> sibling22 -> sibling23 -> null + | | | | + | null null null + | + child11 -> sibling12 -> sibling13 -> sibling14 -> null + | | | | + null null | null + | + child131 -> null + | + null +----------------------------------------------------------------------- + +root ('/') + | +testcase-data -> child1 -> sibling2 -> sibling3 -> sibling4 -> null + | | | | | + | (...) (...) (...) null + | +test-sibling3 -> test-sibling2 -> test-sibling1 -> test-child0 -> null + | | | | + null null null test-child01 + + +Figure 3: Live device tree structure after attaching the testcase-data. + + +Astute readers would have noticed that test-child0 node becomes the last +sibling compared to the earlier structure (Figure 2). After attaching first +test-child0 the test-sibling1 is attached that pushes the child node +(i.e. test-child0) to become a sibling and makes itself a child node, + as mentioned above. + +If a duplicate node is found (i.e. if a node with same full_name property is +already present in the live tree), then the node isn't attached rather its +properties are updated to the live tree's node by calling the function +update_node_properties(). + + +2.2. Removing the test data + +Once the test case execution is complete, selftest_data_remove is called in +order to remove the device nodes attached initially (first the leaf nodes are +detached and then moving up the parent nodes are removed, and eventually the +whole tree). selftest_data_remove() calls detach_node_and_children() that uses +of_detach_node() to detach the nodes from the live device tree. + +To detach a node, of_detach_node() first updates all_next linked list, by +attaching the previous node's allnext to current node's allnext pointer. And +then, it either updates the child pointer of given node's parent to its +sibling or attaches the previous sibling to the given node's sibling, as +appropriate. That is it :) diff --git a/Documentation/devicetree/todo.txt b/Documentation/devicetree/todo.txt new file mode 100644 index 000000000000..c3cf0659bd19 --- /dev/null +++ b/Documentation/devicetree/todo.txt @@ -0,0 +1,11 @@ +Todo list for devicetree: + +=== General structure === +- Switch from custom lists to (h)list_head for nodes and properties structure +- Remove of_allnodes list and iterate using list of child nodes alone + +=== CONFIG_OF_DYNAMIC === +- Switch to RCU for tree updates and get rid of global spinlock +- Document node lifecycle for CONFIG_OF_DYNAMIC +- Always set ->full_name at of_attach_node() time +- pseries: Get rid of open-coded tree modification from arch/powerpc/platforms/pseries/dlpar.c |