aboutsummaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree')
-rw-r--r--Documentation/devicetree/bindings/display/imx/ldb.txt1
-rw-r--r--Documentation/devicetree/bindings/hwmon/ina2xx.txt1
-rw-r--r--Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt4
-rw-r--r--Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt3
-rw-r--r--Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt6
-rw-r--r--Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt4
-rw-r--r--Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt6
-rw-r--r--Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt8
-rw-r--r--Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt5
-rw-r--r--Documentation/devicetree/bindings/spi/spi-bus.txt35
-rw-r--r--Documentation/devicetree/bindings/spi/spi-clps711x.txt33
-rw-r--r--Documentation/devicetree/bindings/spi/spi-davinci.txt2
-rw-r--r--Documentation/devicetree/bindings/spi/ti_qspi.txt2
-rw-r--r--Documentation/devicetree/bindings/vendor-prefixes.txt2
14 files changed, 76 insertions, 36 deletions
diff --git a/Documentation/devicetree/bindings/display/imx/ldb.txt b/Documentation/devicetree/bindings/display/imx/ldb.txt
index 0a175d991b52..a407462c885e 100644
--- a/Documentation/devicetree/bindings/display/imx/ldb.txt
+++ b/Documentation/devicetree/bindings/display/imx/ldb.txt
@@ -62,6 +62,7 @@ Required properties:
display-timings are used instead.
Optional properties (required if display-timings are used):
+ - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
- display-timings : A node that describes the display timings as defined in
Documentation/devicetree/bindings/display/display-timing.txt.
- fsl,data-mapping : should be "spwg" or "jeida"
diff --git a/Documentation/devicetree/bindings/hwmon/ina2xx.txt b/Documentation/devicetree/bindings/hwmon/ina2xx.txt
index 9bcd5e87830d..02af0d94e921 100644
--- a/Documentation/devicetree/bindings/hwmon/ina2xx.txt
+++ b/Documentation/devicetree/bindings/hwmon/ina2xx.txt
@@ -7,6 +7,7 @@ Required properties:
- "ti,ina220" for ina220
- "ti,ina226" for ina226
- "ti,ina230" for ina230
+ - "ti,ina231" for ina231
- reg: I2C address
Optional properties:
diff --git a/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt b/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt
index bfeabb843941..71191ff0e781 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt
@@ -44,8 +44,8 @@ Required properties:
- our-claim-gpio: The GPIO that we use to claim the bus.
- their-claim-gpios: The GPIOs that the other sides use to claim the bus.
Note that some implementations may only support a single other master.
-- Standard I2C mux properties. See mux.txt in this directory.
-- Single I2C child bus node at reg 0. See mux.txt in this directory.
+- Standard I2C mux properties. See i2c-mux.txt in this directory.
+- Single I2C child bus node at reg 0. See i2c-mux.txt in this directory.
Optional properties:
- slew-delay-us: microseconds to wait for a GPIO to go high. Default is 10 us.
diff --git a/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt b/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt
index 6078aefe7ed4..7ce23ac61308 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt
@@ -27,7 +27,8 @@ Required properties:
- i2c-bus-name: The name of this bus. Also needed as pinctrl-name for the I2C
parents.
-Furthermore, I2C mux properties and child nodes. See mux.txt in this directory.
+Furthermore, I2C mux properties and child nodes. See i2c-mux.txt in this
+directory.
Example:
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt
index 66709a825541..21da3ecbb370 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt
@@ -22,8 +22,8 @@ Required properties:
- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
port is connected to.
- mux-gpios: list of gpios used to control the muxer
-* Standard I2C mux properties. See mux.txt in this directory.
-* I2C child bus nodes. See mux.txt in this directory.
+* Standard I2C mux properties. See i2c-mux.txt in this directory.
+* I2C child bus nodes. See i2c-mux.txt in this directory.
Optional properties:
- idle-state: value to set the muxer to when idle. When no value is
@@ -33,7 +33,7 @@ For each i2c child node, an I2C child bus will be created. They will
be numbered based on their order in the device tree.
Whenever an access is made to a device on a child bus, the value set
-in the revelant node's reg property will be output using the list of
+in the relevant node's reg property will be output using the list of
GPIOs, the first in the list holding the least-significant value.
If an idle state is defined, using the idle-state (optional) property,
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt
index ae8af1694e95..33119a98e144 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt
@@ -28,9 +28,9 @@ Also required are:
* Standard pinctrl properties that specify the pin mux state for each child
bus. See ../pinctrl/pinctrl-bindings.txt.
-* Standard I2C mux properties. See mux.txt in this directory.
+* Standard I2C mux properties. See i2c-mux.txt in this directory.
-* I2C child bus nodes. See mux.txt in this directory.
+* I2C child bus nodes. See i2c-mux.txt in this directory.
For each named state defined in the pinctrl-names property, an I2C child bus
will be created. I2C child bus numbers are assigned based on the index into
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt
index 688783fbe696..de00d7fc450b 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt
@@ -7,8 +7,8 @@ Required properties:
- compatible: i2c-mux-reg
- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
port is connected to.
-* Standard I2C mux properties. See mux.txt in this directory.
-* I2C child bus nodes. See mux.txt in this directory.
+* Standard I2C mux properties. See i2c-mux.txt in this directory.
+* I2C child bus nodes. See i2c-mux.txt in this directory.
Optional properties:
- reg: this pair of <offset size> specifies the register to control the mux.
@@ -24,7 +24,7 @@ Optional properties:
given, it defaults to the last value used.
Whenever an access is made to a device on a child bus, the value set
-in the revelant node's reg property will be output to the register.
+in the relevant node's reg property will be output to the register.
If an idle state is defined, using the idle-state (optional) property,
whenever an access is not being made to a device on a child bus, the
diff --git a/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt b/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt
index 14aa6cf58201..6a9a63cb0543 100644
--- a/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt
+++ b/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt
@@ -13,10 +13,10 @@ Optional properties:
initialization. This is an array of 28 values(u8).
- marvell,wakeup-pin: It represents wakeup pin number of the bluetooth chip.
- firmware will use the pin to wakeup host system.
+ firmware will use the pin to wakeup host system (u16).
- marvell,wakeup-gap-ms: wakeup gap represents wakeup latency of the host
platform. The value will be configured to firmware. This
- is needed to work chip's sleep feature as expected.
+ is needed to work chip's sleep feature as expected (u16).
- interrupt-parent: phandle of the parent interrupt controller
- interrupts : interrupt pin number to the cpu. Driver will request an irq based
on this interrupt number. During system suspend, the irq will be
@@ -50,7 +50,7 @@ calibration data is also available in below example.
0x37 0x01 0x1c 0x00 0xff 0xff 0xff 0xff 0x01 0x7f 0x04 0x02
0x00 0x00 0xba 0xce 0xc0 0xc6 0x2d 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0xf0 0x00>;
- marvell,wakeup-pin = <0x0d>;
- marvell,wakeup-gap-ms = <0x64>;
+ marvell,wakeup-pin = /bits/ 16 <0x0d>;
+ marvell,wakeup-gap-ms = /bits/ 16 <0x64>;
};
};
diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt
index 523341a0e113..8bc95e2fc47f 100644
--- a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt
+++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt
@@ -11,7 +11,6 @@ Required properties:
- "fsl,imx51-ecspi" for SPI compatible with the one integrated on i.MX51
- reg : Offset and length of the register set for the device
- interrupts : Should contain CSPI/eCSPI interrupt
-- fsl,spi-num-chipselects : Contains the number of the chipselect
- cs-gpios : Specifies the gpio pins to be used for chipselects.
- clocks : Clock specifiers for both ipg and per clocks.
- clock-names : Clock names should include both "ipg" and "per"
@@ -21,6 +20,9 @@ See the clock consumer binding,
Documentation/devicetree/bindings/dma/dma.txt
- dma-names: DMA request names should include "tx" and "rx" if present.
+Obsolete properties:
+- fsl,spi-num-chipselects : Contains the number of the chipselect
+
Example:
ecspi@70010000 {
@@ -29,7 +31,6 @@ ecspi@70010000 {
compatible = "fsl,imx51-ecspi";
reg = <0x70010000 0x4000>;
interrupts = <36>;
- fsl,spi-num-chipselects = <2>;
cs-gpios = <&gpio3 24 0>, /* GPIO3_24 */
<&gpio3 25 0>; /* GPIO3_25 */
dmas = <&sdma 3 7 1>, <&sdma 4 7 2>;
diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt
index 42d595425dfb..17822860cb98 100644
--- a/Documentation/devicetree/bindings/spi/spi-bus.txt
+++ b/Documentation/devicetree/bindings/spi/spi-bus.txt
@@ -8,11 +8,10 @@ in slave mode.
The SPI master node requires the following properties:
- #address-cells - number of cells required to define a chip select
- address on the SPI bus.
+ address on the SPI bus.
- #size-cells - should be zero.
- compatible - name of SPI bus controller following generic names
- recommended practice.
-- cs-gpios - (optional) gpios chip select.
+ recommended practice.
No other properties are required in the SPI bus node. It is assumed
that a driver for an SPI bus device will understand that it is an SPI bus.
However, the binding does not attempt to define the specific method for
@@ -22,11 +21,12 @@ assumption that board specific platform code will be used to manage
chip selects. Individual drivers can define additional properties to
support describing the chip select layout.
-Optional property:
-- num-cs : total number of chipselects
+Optional properties:
+- cs-gpios - gpios chip select.
+- num-cs - total number of chipselects.
-If cs-gpios is used the number of chip select will automatically increased
-with max(cs-gpios > hw cs)
+If cs-gpios is used the number of chip selects will be increased automatically
+with max(cs-gpios > hw cs).
So if for example the controller has 2 CS lines, and the cs-gpios
property looks like this:
@@ -45,29 +45,30 @@ SPI slave nodes must be children of the SPI master node and can
contain the following properties.
- reg - (required) chip select address of device.
- compatible - (required) name of SPI device following generic names
- recommended practice
-- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz
+ recommended practice.
+- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz.
- spi-cpol - (optional) Empty property indicating device requires
- inverse clock polarity (CPOL) mode
+ inverse clock polarity (CPOL) mode.
- spi-cpha - (optional) Empty property indicating device requires
- shifted clock phase (CPHA) mode
+ shifted clock phase (CPHA) mode.
- spi-cs-high - (optional) Empty property indicating device requires
- chip select active high
+ chip select active high.
- spi-3wire - (optional) Empty property indicating device requires
- 3-wire mode.
+ 3-wire mode.
- spi-lsb-first - (optional) Empty property indicating device requires
LSB first mode.
-- spi-tx-bus-width - (optional) The bus width(number of data wires) that
+- spi-tx-bus-width - (optional) The bus width (number of data wires) that is
used for MOSI. Defaults to 1 if not present.
-- spi-rx-bus-width - (optional) The bus width(number of data wires) that
+- spi-rx-bus-width - (optional) The bus width (number of data wires) that is
used for MISO. Defaults to 1 if not present.
- spi-rx-delay-us - (optional) Microsecond delay after a read transfer.
- spi-tx-delay-us - (optional) Microsecond delay after a write transfer.
Some SPI controllers and devices support Dual and Quad SPI transfer mode.
-It allows data in the SPI system to be transferred in 2 wires(DUAL) or 4 wires(QUAD).
+It allows data in the SPI system to be transferred using 2 wires (DUAL) or 4
+wires (QUAD).
Now the value that spi-tx-bus-width and spi-rx-bus-width can receive is
-only 1(SINGLE), 2(DUAL) and 4(QUAD).
+only 1 (SINGLE), 2 (DUAL) and 4 (QUAD).
Dual/Quad mode is not allowed when 3-wire mode is used.
If a gpio chipselect is used for the SPI slave the gpio number will be passed
diff --git a/Documentation/devicetree/bindings/spi/spi-clps711x.txt b/Documentation/devicetree/bindings/spi/spi-clps711x.txt
new file mode 100644
index 000000000000..4c3ec13f423f
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-clps711x.txt
@@ -0,0 +1,33 @@
+Serial Peripheral Interface on Cirrus Logic CL-PS71xx, EP72xx, EP73xx
+
+Required properties
+- #address-cells: must be <1>
+- #size-cells: must be <0>
+- compatible: should include "cirrus,ep7209-spi"
+- reg: Address and length of one register range
+- interrupts: one interrupt line
+- clocks: One entry, refers to the SPI bus clock
+- cs-gpios: Specifies the gpio pins to be used for chipselects.
+ See: Documentation/devicetree/bindings/spi/spi-bus.txt
+
+An additional register is present in the system controller,
+which is assumed to be in the same device tree, with and marked
+as compatible with "cirrus,ep7209-syscon3".
+
+Example:
+
+spi@80000500 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "cirrus,ep7209-spi";
+ reg = <0x80000500 0x4>;
+ interrupts = <15>;
+ clocks = <&clks CLPS711X_CLK_SPI>;
+ status = "disabled";
+};
+
+syscon3: syscon@80002200 {
+ compatible = "cirrus,ep7209-syscon3", "syscon";
+ reg = <0x80002200 0x40>;
+};
+
diff --git a/Documentation/devicetree/bindings/spi/spi-davinci.txt b/Documentation/devicetree/bindings/spi/spi-davinci.txt
index d1e914adcf6e..f5916c92fe91 100644
--- a/Documentation/devicetree/bindings/spi/spi-davinci.txt
+++ b/Documentation/devicetree/bindings/spi/spi-davinci.txt
@@ -21,7 +21,7 @@ Required properties:
IP to the interrupt controller within the SoC. Possible values
are 0 and 1. Manual says one of the two possible interrupt
lines can be tied to the interrupt controller. Set this
- based on a specifc SoC configuration.
+ based on a specific SoC configuration.
- interrupts: interrupt number mapped to CPU.
- clocks: spi clk phandle
diff --git a/Documentation/devicetree/bindings/spi/ti_qspi.txt b/Documentation/devicetree/bindings/spi/ti_qspi.txt
index 50b14f6b53a3..e65fde4a7388 100644
--- a/Documentation/devicetree/bindings/spi/ti_qspi.txt
+++ b/Documentation/devicetree/bindings/spi/ti_qspi.txt
@@ -20,7 +20,7 @@ Optional properties:
chipselect register and offset of that register.
NOTE: TI QSPI controller requires different pinmux and IODelay
-paramaters for Mode-0 and Mode-3 operations, which needs to be set up by
+parameters for Mode-0 and Mode-3 operations, which needs to be set up by
the bootloader (U-Boot). Default configuration only supports Mode-0
operation. Hence, "spi-cpol" and "spi-cpha" DT properties cannot be
specified in the slave nodes of TI QSPI controller without appropriate
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index a7440bcd67ff..2c2500df0dce 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -255,6 +255,7 @@ synology Synology, Inc.
SUNW Sun Microsystems, Inc
tbs TBS Technologies
tcl Toby Churchill Ltd.
+technexion TechNexion
technologic Technologic Systems
thine THine Electronics, Inc.
ti Texas Instruments
@@ -269,6 +270,7 @@ tronsmart Tronsmart
truly Truly Semiconductors Limited
tyan Tyan Computer Corporation
upisemi uPI Semiconductor Corp.
+uniwest United Western Technologies Corp (UniWest)
urt United Radiant Technology Corporation
usi Universal Scientific Industrial Co., Ltd.
v3 V3 Semiconductor