diff options
Diffstat (limited to 'Documentation/devicetree')
78 files changed, 1864 insertions, 710 deletions
diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt deleted file mode 100644 index 061f7b98a07f..000000000000 --- a/Documentation/devicetree/bindings/arm/amlogic.txt +++ /dev/null @@ -1,142 +0,0 @@ -Amlogic MesonX device tree bindings -------------------------------------------- - -Work in progress statement: - -Device tree files and bindings applying to Amlogic SoCs and boards are -considered "unstable". Any Amlogic device tree binding may change at -any time. Be sure to use a device tree binary and a kernel image -generated from the same source tree. - -Please refer to Documentation/devicetree/bindings/ABI.txt for a definition of a -stable binding/ABI. - ---------------------------------------------------------------- - -Boards with the Amlogic Meson6 SoC shall have the following properties: - Required root node property: - compatible: "amlogic,meson6" - -Boards with the Amlogic Meson8 SoC shall have the following properties: - Required root node property: - compatible: "amlogic,meson8"; - -Boards with the Amlogic Meson8b SoC shall have the following properties: - Required root node property: - compatible: "amlogic,meson8b"; - -Boards with the Amlogic Meson8m2 SoC shall have the following properties: - Required root node property: - compatible: "amlogic,meson8m2"; - -Boards with the Amlogic Meson GXBaby SoC shall have the following properties: - Required root node property: - compatible: "amlogic,meson-gxbb"; - -Boards with the Amlogic Meson GXL S905X SoC shall have the following properties: - Required root node property: - compatible: "amlogic,s905x", "amlogic,meson-gxl"; - -Boards with the Amlogic Meson GXL S905D SoC shall have the following properties: - Required root node property: - compatible: "amlogic,s905d", "amlogic,meson-gxl"; - -Boards with the Amlogic Meson GXL S805X SoC shall have the following properties: - Required root node property: - compatible: "amlogic,s805x", "amlogic,meson-gxl"; - -Boards with the Amlogic Meson GXL S905W SoC shall have the following properties: - Required root node property: - compatible: "amlogic,s905w", "amlogic,meson-gxl"; - -Boards with the Amlogic Meson GXM S912 SoC shall have the following properties: - Required root node property: - compatible: "amlogic,s912", "amlogic,meson-gxm"; - -Boards with the Amlogic Meson AXG A113D SoC shall have the following properties: - Required root node property: - compatible: "amlogic,a113d", "amlogic,meson-axg"; - -Boards with the Amlogic Meson G12A S905D2 SoC shall have the following properties: - Required root node property: - compatible: "amlogic,g12a"; - -Board compatible values (alphabetically, grouped by SoC): - - - "geniatech,atv1200" (Meson6) - - - "minix,neo-x8" (Meson8) - - - "endless,ec100" (Meson8b) - - "hardkernel,odroid-c1" (Meson8b) - - "tronfy,mxq" (Meson8b) - - - "tronsmart,mxiii-plus" (Meson8m2) - - - "amlogic,p200" (Meson gxbb) - - "amlogic,p201" (Meson gxbb) - - "friendlyarm,nanopi-k2" (Meson gxbb) - - "hardkernel,odroid-c2" (Meson gxbb) - - "nexbox,a95x" (Meson gxbb or Meson gxl s905x) - - "tronsmart,vega-s95-pro", "tronsmart,vega-s95" (Meson gxbb) - - "tronsmart,vega-s95-meta", "tronsmart,vega-s95" (Meson gxbb) - - "tronsmart,vega-s95-telos", "tronsmart,vega-s95" (Meson gxbb) - - "wetek,hub" (Meson gxbb) - - "wetek,play2" (Meson gxbb) - - - "amlogic,p212" (Meson gxl s905x) - - "hwacom,amazetv" (Meson gxl s905x) - - "khadas,vim" (Meson gxl s905x) - - "libretech,cc" (Meson gxl s905x) - - - "amlogic,p230" (Meson gxl s905d) - - "amlogic,p231" (Meson gxl s905d) - - "phicomm,n1" (Meson gxl s905d) - - - "amlogic,p241" (Meson gxl s805x) - - "libretech,aml-s805x-ac" (Meson gxl s805x) - - - "amlogic,p281" (Meson gxl s905w) - - "oranth,tx3-mini" (Meson gxl s905w) - - - "amlogic,q200" (Meson gxm s912) - - "amlogic,q201" (Meson gxm s912) - - "khadas,vim2" (Meson gxm s912) - - "kingnovel,r-box-pro" (Meson gxm S912) - - "nexbox,a1" (Meson gxm s912) - - "tronsmart,vega-s96" (Meson gxm s912) - - - "amlogic,s400" (Meson axg a113d) - - - "amlogic,u200" (Meson g12a s905d2) - - "amediatech,x96-max" (Meson g12a s905x2) - - "seirobotics,sei510" (Meson g12a s905x2) - -Amlogic Meson Firmware registers Interface ------------------------------------------- - -The Meson SoCs have a register bank with status and data shared with the -secure firmware. - -Required properties: - - compatible: For Meson GX SoCs, must be "amlogic,meson-gx-ao-secure", "syscon" - -Properties should indentify components of this register interface : - -Meson GX SoC Information ------------------------- -A firmware register encodes the SoC type, package and revision information on -the Meson GX SoCs. -If present, the following property should be added : - -Optional properties: - - amlogic,has-chip-id: If present, the interface gives the current SoC version. - -Example -------- - -ao-secure@140 { - compatible = "amlogic,meson-gx-ao-secure", "syscon"; - reg = <0x0 0x140 0x0 0x140>; - amlogic,has-chip-id; -}; diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml new file mode 100644 index 000000000000..325c6fd3566d --- /dev/null +++ b/Documentation/devicetree/bindings/arm/amlogic.yaml @@ -0,0 +1,144 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/amlogic.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic MesonX device tree bindings + +maintainers: + - Kevin Hilman <khilman@baylibre.com> + +description: |+ + Work in progress statement: + + Device tree files and bindings applying to Amlogic SoCs and boards are + considered "unstable". Any Amlogic device tree binding may change at + any time. Be sure to use a device tree binary and a kernel image + generated from the same source tree. + + Please refer to Documentation/devicetree/bindings/ABI.txt for a definition of a + stable binding/ABI. + +properties: + $nodename: + const: '/' + compatible: + oneOf: + - description: Boards with the Amlogic Meson6 SoC + items: + - enum: + - geniatech,atv1200 + - const: amlogic,meson6 + + - description: Boards with the Amlogic Meson8 SoC + items: + - enum: + - minix,neo-x8 + - const: amlogic,meson8 + + - description: Boards with the Amlogic Meson8m2 SoC + items: + - enum: + - tronsmart,mxiii-plus + - const: amlogic,meson8m2 + + - description: Boards with the Amlogic Meson8b SoC + items: + - enum: + - endless,ec100 + - hardkernel,odroid-c1 + - tronfy,mxq + - const: amlogic,meson8b + + - description: Boards with the Amlogic Meson GXBaby SoC + items: + - enum: + - amlogic,p200 + - amlogic,p201 + - friendlyarm,nanopi-k2 + - hardkernel,odroid-c2 + - nexbox,a95x + - wetek,hub + - wetek,play2 + - const: amlogic,meson-gxbb + + - description: Tronsmart Vega S95 devices + items: + - enum: + - tronsmart,vega-s95-pro + - tronsmart,vega-s95-meta + - tronsmart,vega-s95-telos + - const: tronsmart,vega-s95 + - const: amlogic,meson-gxbb + + - description: Boards with the Amlogic Meson GXL S805X SoC + items: + - enum: + - amlogic,p241 + - libretech,aml-s805x-ac + - const: amlogic,s805x + - const: amlogic,meson-gxl + + - description: Boards with the Amlogic Meson GXL S905W SoC + items: + - enum: + - amlogic,p281 + - oranth,tx3-mini + - const: amlogic,s905w + - const: amlogic,meson-gxl + + - description: Boards with the Amlogic Meson GXL S905X SoC + items: + - enum: + - amediatech,x96-max + - amlogic,p212 + - hwacom,amazetv + - khadas,vim + - libretech,cc + - nexbox,a95x + - seirobotics,sei510 + - const: amlogic,s905x + - const: amlogic,meson-gxl + + - description: Boards with the Amlogic Meson GXL S905D SoC + items: + - enum: + - amlogic,p230 + - amlogic,p231 + - phicomm,n1 + - const: amlogic,s905d + - const: amlogic,meson-gxl + + - description: Boards with the Amlogic Meson GXM S912 SoC + items: + - enum: + - amlogic,q200 + - amlogic,q201 + - khadas,vim2 + - kingnovel,r-box-pro + - nexbox,a1 + - tronsmart,vega-s96 + - const: amlogic,s912 + - const: amlogic,meson-gxm + + - description: Boards with the Amlogic Meson AXG A113D SoC + items: + - enum: + - amlogic,s400 + - const: amlogic,a113d + - const: amlogic,meson-axg + + - description: Boards with the Amlogic Meson G12A S905D2 SoC + items: + - enum: + - amlogic,u200 + - const: amlogic,g12a + + - description: Boards with the Amlogic Meson G12B S922X SoC + items: + - enum: + - hardkernel,odroid-n2 + - const: amlogic,g12b + +... diff --git a/Documentation/devicetree/bindings/arm/amlogic/amlogic,meson-gx-ao-secure.txt b/Documentation/devicetree/bindings/arm/amlogic/amlogic,meson-gx-ao-secure.txt new file mode 100644 index 000000000000..c67d9f48fb91 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/amlogic/amlogic,meson-gx-ao-secure.txt @@ -0,0 +1,28 @@ +Amlogic Meson Firmware registers Interface +------------------------------------------ + +The Meson SoCs have a register bank with status and data shared with the +secure firmware. + +Required properties: + - compatible: For Meson GX SoCs, must be "amlogic,meson-gx-ao-secure", "syscon" + +Properties should indentify components of this register interface : + +Meson GX SoC Information +------------------------ +A firmware register encodes the SoC type, package and revision information on +the Meson GX SoCs. +If present, the following property should be added : + +Optional properties: + - amlogic,has-chip-id: If present, the interface gives the current SoC version. + +Example +------- + +ao-secure@140 { + compatible = "amlogic,meson-gx-ao-secure", "syscon"; + reg = <0x0 0x140 0x0 0x140>; + amlogic,has-chip-id; +}; diff --git a/Documentation/devicetree/bindings/arm/arm,scmi.txt b/Documentation/devicetree/bindings/arm/arm,scmi.txt index 5f3719ab7075..317a2fc3667a 100644 --- a/Documentation/devicetree/bindings/arm/arm,scmi.txt +++ b/Documentation/devicetree/bindings/arm/arm,scmi.txt @@ -6,7 +6,7 @@ that are provided by the hardware platform it is running on, including power and performance functions. This binding is intended to define the interface the firmware implementing -the SCMI as described in ARM document number ARM DUI 0922B ("ARM System Control +the SCMI as described in ARM document number ARM DEN 0056A ("ARM System Control and Management Interface Platform Design Document")[0] provide for OSPM in the device tree. diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt deleted file mode 100644 index 99dee23c74a4..000000000000 --- a/Documentation/devicetree/bindings/arm/atmel-at91.txt +++ /dev/null @@ -1,73 +0,0 @@ -Atmel AT91 device tree bindings. -================================ - -Boards with a SoC of the Atmel AT91 or SMART family shall have the following -properties: - -Required root node properties: -compatible: must be one of: - * "atmel,at91rm9200" - - * "atmel,at91sam9" for SoCs using an ARM926EJ-S core, shall be extended with - the specific SoC family or compatible: - o "atmel,at91sam9260" - o "atmel,at91sam9261" - o "atmel,at91sam9263" - o "atmel,at91sam9x5" for the 5 series, shall be extended with the specific - SoC compatible: - - "atmel,at91sam9g15" - - "atmel,at91sam9g25" - - "atmel,at91sam9g35" - - "atmel,at91sam9x25" - - "atmel,at91sam9x35" - o "atmel,at91sam9g20" - o "atmel,at91sam9g45" - o "atmel,at91sam9n12" - o "atmel,at91sam9rl" - o "atmel,at91sam9xe" - o "microchip,sam9x60" - * "atmel,sama5" for SoCs using a Cortex-A5, shall be extended with the specific - SoC family: - o "atmel,sama5d2" shall be extended with the specific SoC compatible: - - "atmel,sama5d27" - o "atmel,sama5d3" shall be extended with the specific SoC compatible: - - "atmel,sama5d31" - - "atmel,sama5d33" - - "atmel,sama5d34" - - "atmel,sama5d35" - - "atmel,sama5d36" - o "atmel,sama5d4" shall be extended with the specific SoC compatible: - - "atmel,sama5d41" - - "atmel,sama5d42" - - "atmel,sama5d43" - - "atmel,sama5d44" - - * "atmel,samv7" for MCUs using a Cortex-M7, shall be extended with the specific - SoC family: - o "atmel,sams70" shall be extended with the specific MCU compatible: - - "atmel,sams70j19" - - "atmel,sams70j20" - - "atmel,sams70j21" - - "atmel,sams70n19" - - "atmel,sams70n20" - - "atmel,sams70n21" - - "atmel,sams70q19" - - "atmel,sams70q20" - - "atmel,sams70q21" - o "atmel,samv70" shall be extended with the specific MCU compatible: - - "atmel,samv70j19" - - "atmel,samv70j20" - - "atmel,samv70n19" - - "atmel,samv70n20" - - "atmel,samv70q19" - - "atmel,samv70q20" - o "atmel,samv71" shall be extended with the specific MCU compatible: - - "atmel,samv71j19" - - "atmel,samv71j20" - - "atmel,samv71j21" - - "atmel,samv71n19" - - "atmel,samv71n20" - - "atmel,samv71n21" - - "atmel,samv71q19" - - "atmel,samv71q20" - - "atmel,samv71q21" diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.yaml b/Documentation/devicetree/bindings/arm/atmel-at91.yaml new file mode 100644 index 000000000000..6e168abcd4d1 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/atmel-at91.yaml @@ -0,0 +1,134 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/atmel-at91.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Atmel AT91 device tree bindings. + +maintainers: + - Alexandre Belloni <alexandre.belloni@bootlin.com> + - Ludovic Desroches <ludovic.desroches@microchip.com> + +description: | + Boards with a SoC of the Atmel AT91 or SMART family shall have the following + +properties: + $nodename: + const: '/' + compatible: + oneOf: + - items: + - const: atmel,at91rm9200 + - items: + - enum: + - olimex,sam9-l9260 + - enum: + - atmel,at91sam9260 + - atmel,at91sam9261 + - atmel,at91sam9263 + - atmel,at91sam9g20 + - atmel,at91sam9g45 + - atmel,at91sam9n12 + - atmel,at91sam9rl + - atmel,at91sam9xe + - atmel,at91sam9x60 + - const: atmel,at91sam9 + + - items: + - enum: + - atmel,at91sam9g15 + - atmel,at91sam9g25 + - atmel,at91sam9g35 + - atmel,at91sam9x25 + - atmel,at91sam9x35 + - const: atmel,at91sam9x5 + - const: atmel,at91sam9 + + - items: + - const: atmel,sama5d27 + - const: atmel,sama5d2 + - const: atmel,sama5 + + - description: Nattis v2 board with Natte v2 power board + items: + - const: axentia,nattis-2 + - const: axentia,natte-2 + - const: axentia,linea + - const: atmel,sama5d31 + - const: atmel,sama5d3 + - const: atmel,sama5 + + - description: TSE-850 v3 board + items: + - const: axentia,tse850v3 + - const: axentia,linea + - const: atmel,sama5d31 + - const: atmel,sama5d3 + - const: atmel,sama5 + + - items: + - const: axentia,linea + - const: atmel,sama5d31 + - const: atmel,sama5d3 + - const: atmel,sama5 + + - items: + - enum: + - atmel,sama5d31 + - atmel,sama5d33 + - atmel,sama5d34 + - atmel,sama5d35 + - atmel,sama5d36 + - const: atmel,sama5d3 + - const: atmel,sama5 + + - items: + - enum: + - atmel,sama5d41 + - atmel,sama5d42 + - atmel,sama5d43 + - atmel,sama5d44 + - const: atmel,sama5d4 + - const: atmel,sama5 + + - items: + - enum: + - atmel,sams70j19 + - atmel,sams70j20 + - atmel,sams70j21 + - atmel,sams70n19 + - atmel,sams70n20 + - atmel,sams70n21 + - atmel,sams70q19 + - atmel,sams70q20 + - atmel,sams70q21 + - const: atmel,sams70 + - const: atmel,samv7 + + - items: + - enum: + - atmel,samv70j19 + - atmel,samv70j20 + - atmel,samv70n19 + - atmel,samv70n20 + - atmel,samv70q19 + - atmel,samv70q20 + - const: atmel,samv70 + - const: atmel,samv7 + + - items: + - enum: + - atmel,samv71j19 + - atmel,samv71j20 + - atmel,samv71j21 + - atmel,samv71n19 + - atmel,samv71n20 + - atmel,samv71n21 + - atmel,samv71q19 + - atmel,samv71q20 + - atmel,samv71q21 + - const: atmel,samv71 + - const: atmel,samv7 + +... diff --git a/Documentation/devicetree/bindings/arm/emtrion.txt b/Documentation/devicetree/bindings/arm/emtrion.txt deleted file mode 100644 index 83329aefc483..000000000000 --- a/Documentation/devicetree/bindings/arm/emtrion.txt +++ /dev/null @@ -1,12 +0,0 @@ -Emtrion Devicetree Bindings -=========================== - -emCON Series: -------------- - -Required root node properties - - compatible: - - "emtrion,emcon-mx6", "fsl,imx6q"; : emCON-MX6D or emCON-MX6Q SoM - - "emtrion,emcon-mx6-avari", "fsl,imx6q"; : emCON-MX6D or emCON-MX6Q SoM on Avari Base - - "emtrion,emcon-mx6", "fsl,imx6dl"; : emCON-MX6S or emCON-MX6DL SoM - - "emtrion,emcon-mx6-avari", "fsl,imx6dl"; : emCON-MX6S or emCON-MX6DL SoM on Avari Base diff --git a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt index f378922906f6..a575e42f7fec 100644 --- a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt +++ b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt @@ -145,6 +145,16 @@ Optional Child nodes: - Data cells of ocotp: Detailed bindings are described in bindings/nvmem/nvmem.txt +Watchdog bindings based on SCU Message Protocol +------------------------------------------------------------ + +Required properties: +- compatible: should be: + "fsl,imx8qxp-sc-wdt" + followed by "fsl,imx-sc-wdt"; +Optional properties: +- timeout-sec: contains the watchdog timeout in seconds. + Example (imx8qxp): ------------- aliases { @@ -207,6 +217,11 @@ firmware { rtc: rtc { compatible = "fsl,imx8qxp-sc-rtc"; }; + + watchdog { + compatible = "fsl,imx8qxp-sc-wdt", "fsl,imx-sc-wdt"; + timeout-sec = <60>; + }; }; }; diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index 407138ebc0d0..7294ac36f4c0 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -15,6 +15,13 @@ properties: const: '/' compatible: oneOf: + - description: i.MX1 based Boards + items: + - enum: + - armadeus,imx1-apf9328 + - fsl,imx1ads + - const: fsl,imx1 + - description: i.MX23 based Boards items: - enum: @@ -51,6 +58,25 @@ properties: - const: i2se,duckbill-2 - const: fsl,imx28 + - description: i.MX31 based Boards + items: + - enum: + - buglabs,imx31-bug + - logicpd,imx31-lite + - const: fsl,imx31 + + - description: i.MX35 based Boards + items: + - enum: + - fsl,imx35-pdk + - const: fsl,imx35 + + - description: i.MX35 Eukrea CPUIMX35 Board + items: + - const: eukrea,mbimxsd35-baseboard + - const: eukrea,cpuimx35 + - const: fsl,imx35 + - description: i.MX50 based Boards items: - enum: @@ -80,6 +106,8 @@ properties: - description: i.MX6Q based Boards items: - enum: + - emtrion,emcon-mx6 # emCON-MX6D or emCON-MX6Q SoM + - emtrion,emcon-mx6-avari # emCON-MX6D or emCON-MX6Q SoM on Avari Base - fsl,imx6q-arm2 - fsl,imx6q-sabreauto - fsl,imx6q-sabrelite @@ -99,6 +127,8 @@ properties: items: - enum: - eckelmann,imx6dl-ci4x10 + - emtrion,emcon-mx6 # emCON-MX6S or emCON-MX6DL SoM + - emtrion,emcon-mx6-avari # emCON-MX6S or emCON-MX6DL SoM on Avari Base - fsl,imx6dl-sabreauto # i.MX6 DualLite/Solo SABRE Automotive Board - fsl,imx6dl-sabresd # i.MX6 DualLite SABRE Smart Device Board - technologic,imx6dl-ts4900 @@ -156,6 +186,7 @@ properties: items: - enum: - fsl,imx7d-sdb # i.MX7 SabreSD Board + - novtech,imx7d-meerkat96 # i.MX7 Meerkat96 Board - tq,imx7d-mba7 # i.MX7D TQ MBa7 with TQMa7D SoM - zii,imx7d-rpu2 # ZII RPU2 Board - const: fsl,imx7d @@ -171,12 +202,25 @@ properties: - const: compulab,cl-som-imx7 - const: fsl,imx7d + - description: i.MX7ULP based Boards + items: + - enum: + - fsl,imx7ulp-evk # i.MX7ULP Evaluation Kit + - const: fsl,imx7ulp + - description: i.MX8MM based Boards items: - enum: - fsl,imx8mm-evk # i.MX8MM EVK Board - const: fsl,imx8mm + - description: i.MX8MQ based Boards + items: + - enum: + - fsl,imx8mq-evk # i.MX8MQ EVK Board + - purism,librem5-devkit # Purism Librem5 devkit + - const: fsl,imx8mq + - description: i.MX8QXP based Boards items: - enum: diff --git a/Documentation/devicetree/bindings/arm/mediatek.txt b/Documentation/devicetree/bindings/arm/mediatek.txt deleted file mode 100644 index 56ac7896d6d8..000000000000 --- a/Documentation/devicetree/bindings/arm/mediatek.txt +++ /dev/null @@ -1,89 +0,0 @@ -MediaTek SoC based Platforms Device Tree Bindings - -Boards with a MediaTek SoC shall have the following property: - -Required root node property: - -compatible: Must contain one of - "mediatek,mt2701" - "mediatek,mt2712" - "mediatek,mt6580" - "mediatek,mt6589" - "mediatek,mt6592" - "mediatek,mt6755" - "mediatek,mt6765" - "mediatek,mt6795" - "mediatek,mt6797" - "mediatek,mt7622" - "mediatek,mt7623" - "mediatek,mt7629" - "mediatek,mt8127" - "mediatek,mt8135" - "mediatek,mt8173" - "mediatek,mt8183" - - -Supported boards: - -- Evaluation board for MT2701: - Required root node properties: - - compatible = "mediatek,mt2701-evb", "mediatek,mt2701"; -- Evaluation board for MT2712: - Required root node properties: - - compatible = "mediatek,mt2712-evb", "mediatek,mt2712"; -- Evaluation board for MT6580: - Required root node properties: - - compatible = "mediatek,mt6580-evbp1", "mediatek,mt6580"; -- bq Aquaris5 smart phone: - Required root node properties: - - compatible = "mundoreader,bq-aquaris5", "mediatek,mt6589"; -- Evaluation board for MT6592: - Required root node properties: - - compatible = "mediatek,mt6592-evb", "mediatek,mt6592"; -- Evaluation phone for MT6755(Helio P10): - Required root node properties: - - compatible = "mediatek,mt6755-evb", "mediatek,mt6755"; -- Evaluation board for MT6765(Helio P22): - Required root node properties: - - compatible = "mediatek,mt6765-evb", "mediatek,mt6765"; -- Evaluation board for MT6795(Helio X10): - Required root node properties: - - compatible = "mediatek,mt6795-evb", "mediatek,mt6795"; -- Evaluation board for MT6797(Helio X20): - Required root node properties: - - compatible = "mediatek,mt6797-evb", "mediatek,mt6797"; -- Mediatek X20 Development Board: - Required root node properties: - - compatible = "archermind,mt6797-x20-dev", "mediatek,mt6797"; -- Reference board variant 1 for MT7622: - Required root node properties: - - compatible = "mediatek,mt7622-rfb1", "mediatek,mt7622"; -- Bananapi BPI-R64 for MT7622: - Required root node properties: - - compatible = "bananapi,bpi-r64", "mediatek,mt7622"; -- Reference board for MT7623a with eMMC: - Required root node properties: - - compatible = "mediatek,mt7623a-rfb-emmc", "mediatek,mt7623"; -- Reference board for MT7623a with NAND: - Required root node properties: - - compatible = "mediatek,mt7623a-rfb-nand", "mediatek,mt7623"; -- Reference board for MT7623n with eMMC: - Required root node properties: - - compatible = "mediatek,mt7623n-rfb-emmc", "mediatek,mt7623"; -- Bananapi BPI-R2 board: - - compatible = "bananapi,bpi-r2", "mediatek,mt7623"; -- Reference board for MT7629: - Required root node properties: - - compatible = "mediatek,mt7629-rfb", "mediatek,mt7629"; -- MTK mt8127 tablet moose EVB: - Required root node properties: - - compatible = "mediatek,mt8127-moose", "mediatek,mt8127"; -- MTK mt8135 tablet EVB: - Required root node properties: - - compatible = "mediatek,mt8135-evbp1", "mediatek,mt8135"; -- MTK mt8173 tablet EVB: - Required root node properties: - - compatible = "mediatek,mt8173-evb", "mediatek,mt8173"; -- Evaluation board for MT8183: - Required root node properties: - - compatible = "mediatek,mt8183-evb", "mediatek,mt8183"; diff --git a/Documentation/devicetree/bindings/arm/mediatek.yaml b/Documentation/devicetree/bindings/arm/mediatek.yaml new file mode 100644 index 000000000000..a4ad2eb926f9 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mediatek.yaml @@ -0,0 +1,91 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/mediatek.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek SoC based Platforms Device Tree Bindings + +maintainers: + - Sean Wang <sean.wang@mediatek.com> + - Matthias Brugger <matthias.bgg@gmail.com> +description: | + Boards with a MediaTek SoC shall have the following properties. + +properties: + $nodename: + const: '/' + compatible: + oneOf: + - items: + - enum: + - mediatek,mt2701-evb + - const: mediatek,mt2701 + + - items: + - enum: + - mediatek,mt2712-evb + - const: mediatek,mt2712 + - items: + - enum: + - mediatek,mt6580-evbp1 + - const: mediatek,mt6580 + - items: + - enum: + - mundoreader,bq-aquaris5 + - const: mediatek,mt6589 + - items: + - enum: + - mediatek,mt6592-evb + - const: mediatek,mt6592 + - items: + - enum: + - mediatek,mt6755-evb + - const: mediatek,mt6755 + - items: + - enum: + - mediatek,mt6765-evb + - const: mediatek,mt6765 + - items: + - enum: + - mediatek,mt6795-evb + - const: mediatek,mt6795 + - items: + - enum: + - archermind,mt6797-x20-dev + - mediatek,mt6797-evb + - const: mediatek,mt6797 + - items: + - enum: + - bananapi,bpi-r64 + - mediatek,mt7622-rfb1 + - const: mediatek,mt7622 + - items: + - enum: + - mediatek,mt7623a-rfb-emmc + - mediatek,mt7623a-rfb-nand + - mediatek,mt7623n-rfb-emmc + - bananapi,bpi-r2 + - const: mediatek,mt7623 + + - items: + - enum: + - mediatek,mt7629-rfb + - const: mediatek,mt7629 + - items: + - enum: + - mediatek,mt8127-moose + - const: mediatek,mt8127 + - items: + - enum: + - mediatek,mt8135-evbp1 + - const: mediatek,mt8135 + - items: + - enum: + - mediatek,mt8173-evb + - const: mediatek,mt8173 + - items: + - enum: + - mediatek,mt8183-evb + - const: mediatek,mt8183 +... diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt index f3cef1a6d95c..07c9d813465c 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt @@ -10,6 +10,7 @@ Required Properties: - "mediatek,mt7622-audsys", "syscon" - "mediatek,mt7623-audsys", "mediatek,mt2701-audsys", "syscon" - "mediatek,mt8183-audiosys", "syscon" + - "mediatek,mt8516-audsys", "syscon" - #clock-cells: Must be 1 The AUDSYS controller uses the common clk binding from diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 1c1e48fd94b5..b301f753ed2c 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -160,6 +160,9 @@ Boards: - AM335X phyCORE-AM335x: Development kit compatible = "phytec,am335x-pcm-953", "phytec,am335x-phycore-som", "ti,am33xx" +- AM335x phyBOARD-REGOR: Single Board Computer + compatible = "phytec,am335x-regor", "phytec,am335x-phycore-som", "ti,am33xx" + - AM335X UC-8100-ME-T: Communication-centric industrial computing platform compatible = "moxa,uc-8100-me-t", "ti,am33xx"; diff --git a/Documentation/devicetree/bindings/arm/renesas.yaml b/Documentation/devicetree/bindings/arm/renesas.yaml index 19f379863d50..08c923f8c257 100644 --- a/Documentation/devicetree/bindings/arm/renesas.yaml +++ b/Documentation/devicetree/bindings/arm/renesas.yaml @@ -106,6 +106,14 @@ properties: - description: RZ/G2M (R8A774A1) items: + - enum: + - hoperun,hihope-rzg2m # HopeRun HiHope RZ/G2M platform + - const: renesas,r8a774a1 + + - items: + - enum: + - hoperun,hihope-rzg2-ex # HopeRun expansion board for HiHope RZ/G2 platforms + - const: hoperun,hihope-rzg2m - const: renesas,r8a774a1 - description: RZ/G2E (R8A774C0) diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml index 5c6bbf10abc9..34865042f4e4 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.yaml +++ b/Documentation/devicetree/bindings/arm/rockchip.yaml @@ -316,6 +316,19 @@ properties: - const: haoyu,marsboard-rk3066 - const: rockchip,rk3066a + - description: Hugsun X99 TV Box + items: + - const: hugsun,x99 + - const: rockchip,rk3399 + + - description: Khadas Edge series boards + items: + - enum: + - khadas,edge + - khadas,edge-captain + - khadas,edge-v + - const: rockchip,rk3399 + - description: mqmaker MiQi items: - const: mqmaker,miqi diff --git a/Documentation/devicetree/bindings/arm/stm32/mlahb.txt b/Documentation/devicetree/bindings/arm/stm32/mlahb.txt new file mode 100644 index 000000000000..25307aa1eb9b --- /dev/null +++ b/Documentation/devicetree/bindings/arm/stm32/mlahb.txt @@ -0,0 +1,37 @@ +ML-AHB interconnect bindings + +These bindings describe the STM32 SoCs ML-AHB interconnect bus which connects +a Cortex-M subsystem with dedicated memories. +The MCU SRAM and RETRAM memory parts can be accessed through different addresses +(see "RAM aliases" in [1]) using different buses (see [2]) : balancing the +Cortex-M firmware accesses among those ports allows to tune the system +performance. + +[1]: https://www.st.com/resource/en/reference_manual/dm00327659.pdf +[2]: https://wiki.st.com/stm32mpu/wiki/STM32MP15_RAM_mapping + +Required properties: +- compatible: should be "simple-bus" +- dma-ranges: describes memory addresses translation between the local CPU and + the remote Cortex-M processor. Each memory region, is declared with + 3 parameters: + - param 1: device base address (Cortex-M processor address) + - param 2: physical base address (local CPU address) + - param 3: size of the memory region. + +The Cortex-M remote processor accessed via the mlahb interconnect is described +by a child node. + +Example: +mlahb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + dma-ranges = <0x00000000 0x38000000 0x10000>, + <0x10000000 0x10000000 0x60000>, + <0x30000000 0x30000000 0x60000>; + + m4_rproc: m4@10000000 { + ... + }; +}; diff --git a/Documentation/devicetree/bindings/arm/stm32/stm32.txt b/Documentation/devicetree/bindings/arm/stm32/stm32.txt deleted file mode 100644 index 6808ed9ddfd5..000000000000 --- a/Documentation/devicetree/bindings/arm/stm32/stm32.txt +++ /dev/null @@ -1,10 +0,0 @@ -STMicroelectronics STM32 Platforms Device Tree Bindings - -Each device tree must specify which STM32 SoC it uses, -using one of the following compatible strings: - - st,stm32f429 - st,stm32f469 - st,stm32f746 - st,stm32h743 - st,stm32mp157 diff --git a/Documentation/devicetree/bindings/arm/stm32/stm32.yaml b/Documentation/devicetree/bindings/arm/stm32/stm32.yaml new file mode 100644 index 000000000000..4d194f1eb03a --- /dev/null +++ b/Documentation/devicetree/bindings/arm/stm32/stm32.yaml @@ -0,0 +1,31 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/stm32/stm32.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics STM32 Platforms Device Tree Bindings + +maintainers: + - Alexandre Torgue <alexandre.torgue@st.com> + +properties: + compatible: + oneOf: + - items: + - const: st,stm32f429 + + - items: + - const: st,stm32f469 + + - items: + - const: st,stm32f746 + + - items: + - const: st,stm32h743 + + - items: + - enum: + - arrow,stm32mp157a-avenger96 # Avenger96 + - const: st,stm32mp157 +... diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml index 285f4fc8519d..000a00d12d6a 100644 --- a/Documentation/devicetree/bindings/arm/sunxi.yaml +++ b/Documentation/devicetree/bindings/arm/sunxi.yaml @@ -263,7 +263,7 @@ properties: - description: ICNova A20 SWAC items: - - const: swac,icnova-a20-swac + - const: incircuit,icnova-a20-swac - const: incircuit,icnova-a20 - const: allwinner,sun7i-a20 diff --git a/Documentation/devicetree/bindings/arm/ti/k3.txt b/Documentation/devicetree/bindings/arm/ti/k3.txt index 6a059cabb2da..333e7256126a 100644 --- a/Documentation/devicetree/bindings/arm/ti/k3.txt +++ b/Documentation/devicetree/bindings/arm/ti/k3.txt @@ -13,6 +13,9 @@ architecture it uses, using one of the following compatible values: - AM654 compatible = "ti,am654"; +- J721E + compatible = "ti,j721e"; + Boards ------ diff --git a/Documentation/devicetree/bindings/arm/xen.txt b/Documentation/devicetree/bindings/arm/xen.txt index c9b9321434ea..db5c56db30ec 100644 --- a/Documentation/devicetree/bindings/arm/xen.txt +++ b/Documentation/devicetree/bindings/arm/xen.txt @@ -54,7 +54,7 @@ hypervisor { }; The format and meaning of the "xen,uefi-*" parameters are similar to those in -Documentation/arm/uefi.txt, which are provided by the regular UEFI stub. However +Documentation/arm/uefi.rst, which are provided by the regular UEFI stub. However they differ because they are provided by the Xen hypervisor, together with a set of UEFI runtime services implemented via hypercalls, see http://xenbits.xen.org/docs/unstable/hypercall/x86_64/include,public,platform.h.html. diff --git a/Documentation/devicetree/bindings/bus/allwinner,sun8i-a23-rsb.yaml b/Documentation/devicetree/bindings/bus/allwinner,sun8i-a23-rsb.yaml new file mode 100644 index 000000000000..fc2f63860cc8 --- /dev/null +++ b/Documentation/devicetree/bindings/bus/allwinner,sun8i-a23-rsb.yaml @@ -0,0 +1,79 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/bus/allwinner,sun8i-a23-rsb.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A23 RSB Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + compatible: + oneOf: + - const: allwinner,sun8i-a23-rsb + - items: + - const: allwinner,sun8i-a83t-rsb + - const: allwinner,sun8i-a23-rsb + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + clock-frequency: + minimum: 1 + maximum: 20000000 + +patternProperties: + "^.*@[0-9a-fA-F]+$": + properties: + reg: + maxItems: 1 + + required: + - reg + +required: + - compatible + - reg + - interrupts + - clocks + - resets + +examples: + - | + rsb@1f03400 { + compatible = "allwinner,sun8i-a23-rsb"; + reg = <0x01f03400 0x400>; + interrupts = <0 39 4>; + clocks = <&apb0_gates 3>; + clock-frequency = <3000000>; + resets = <&apb0_rst 3>; + #address-cells = <1>; + #size-cells = <0>; + + pmic@3e3 { + compatible = "..."; + reg = <0x3e3>; + + /* ... */ + }; + }; + +additionalProperties: false diff --git a/Documentation/devicetree/bindings/bus/sunxi-rsb.txt b/Documentation/devicetree/bindings/bus/sunxi-rsb.txt deleted file mode 100644 index eb3ed628c6f1..000000000000 --- a/Documentation/devicetree/bindings/bus/sunxi-rsb.txt +++ /dev/null @@ -1,47 +0,0 @@ -Allwinner Reduced Serial Bus (RSB) controller - -The RSB controller found on later Allwinner SoCs is an SMBus like 2 wire -serial bus with 1 master and up to 15 slaves. It is represented by a node -for the controller itself, and child nodes representing the slave devices. - -Required properties : - - - reg : Offset and length of the register set for the controller. - - compatible : Shall be "allwinner,sun8i-a23-rsb". - - interrupts : The interrupt line associated to the RSB controller. - - clocks : The gate clk associated to the RSB controller. - - resets : The reset line associated to the RSB controller. - - #address-cells : shall be 1 - - #size-cells : shall be 0 - -Optional properties : - - - clock-frequency : Desired RSB bus clock frequency in Hz. Maximum is 20MHz. - If not set this defaults to 3MHz. - -Child nodes: - -An RSB controller node can contain zero or more child nodes representing -slave devices on the bus. Child 'reg' properties should contain the slave -device's hardware address. The hardware address is hardwired in the device, -which can normally be found in the datasheet. - -Example: - - rsb@1f03400 { - compatible = "allwinner,sun8i-a23-rsb"; - reg = <0x01f03400 0x400>; - interrupts = <0 39 4>; - clocks = <&apb0_gates 3>; - clock-frequency = <3000000>; - resets = <&apb0_rst 3>; - #address-cells = <1>; - #size-cells = <0>; - - pmic@3e3 { - compatible = "..."; - reg = <0x3e3>; - - /* ... */ - }; - }; diff --git a/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml b/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml new file mode 100644 index 000000000000..c935405458fe --- /dev/null +++ b/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml @@ -0,0 +1,141 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/allwinner,sun4i-a10-ccu.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner Clock Control Unit Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + "#clock-cells": + const: 1 + + "#reset-cells": + const: 1 + + compatible: + enum: + - allwinner,sun4i-a10-ccu + - allwinner,sun5i-a10s-ccu + - allwinner,sun5i-a13-ccu + - allwinner,sun6i-a31-ccu + - allwinner,sun7i-a20-ccu + - allwinner,sun8i-a23-ccu + - allwinner,sun8i-a33-ccu + - allwinner,sun8i-a83t-ccu + - allwinner,sun8i-a83t-r-ccu + - allwinner,sun8i-h3-ccu + - allwinner,sun8i-h3-r-ccu + - allwinner,sun8i-r40-ccu + - allwinner,sun8i-v3s-ccu + - allwinner,sun9i-a80-ccu + - allwinner,sun50i-a64-ccu + - allwinner,sun50i-a64-r-ccu + - allwinner,sun50i-h5-ccu + - allwinner,sun50i-h6-ccu + - allwinner,sun50i-h6-r-ccu + - allwinner,suniv-f1c100s-ccu + - nextthing,gr8-ccu + + reg: + maxItems: 1 + + clocks: + minItems: 2 + maxItems: 4 + items: + - description: High Frequency Oscillator (usually at 24MHz) + - description: Low Frequency Oscillator (usually at 32kHz) + - description: Internal Oscillator + - description: Peripherals PLL + + clock-names: + minItems: 2 + maxItems: 4 + items: + - const: hosc + - const: losc + - const: iosc + - const: pll-periph + +required: + - "#clock-cells" + - "#reset-cells" + - compatible + - reg + - clocks + - clock-names + +if: + properties: + compatible: + enum: + - allwinner,sun8i-a83t-r-ccu + - allwinner,sun8i-h3-r-ccu + - allwinner,sun50i-a64-r-ccu + - allwinner,sun50i-h6-r-ccu + +then: + properties: + clocks: + minItems: 4 + maxItems: 4 + + clock-names: + minItems: 4 + maxItems: 4 + +else: + if: + properties: + compatible: + const: allwinner,sun50i-h6-ccu + + then: + properties: + clocks: + minItems: 3 + maxItems: 3 + + clock-names: + minItems: 3 + maxItems: 3 + + else: + properties: + clocks: + minItems: 2 + maxItems: 2 + + clock-names: + minItems: 2 + maxItems: 2 + +additionalProperties: false + +examples: + - | + ccu: clock@1c20000 { + compatible = "allwinner,sun8i-h3-ccu"; + reg = <0x01c20000 0x400>; + clocks = <&osc24M>, <&osc32k>; + clock-names = "hosc", "losc"; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + - | + r_ccu: clock@1f01400 { + compatible = "allwinner,sun50i-a64-r-ccu"; + reg = <0x01f01400 0x100>; + clocks = <&osc24M>, <&osc32k>, <&iosc>, <&ccu 11>; + clock-names = "hosc", "losc", "iosc", "pll-periph"; + #clock-cells = <1>; + #reset-cells = <1>; + }; + +... diff --git a/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt index 5c8b105be4d6..6eaa52092313 100644 --- a/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt +++ b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt @@ -10,6 +10,7 @@ Required Properties: "amlogic,gxl-clkc" for GXL and GXM SoC, "amlogic,axg-clkc" for AXG SoC. "amlogic,g12a-clkc" for G12A SoC. + "amlogic,g12b-clkc" for G12B SoC. - clocks : list of clock phandle, one for each entry clock-names. - clock-names : should contain the following: * "xtal": the platform xtal diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt index b520280e33ff..13f45db3b66d 100644 --- a/Documentation/devicetree/bindings/clock/at91-clock.txt +++ b/Documentation/devicetree/bindings/clock/at91-clock.txt @@ -9,10 +9,11 @@ Slow Clock controller: Required properties: - compatible : shall be one of the following: "atmel,at91sam9x5-sckc", - "atmel,sama5d3-sckc" or - "atmel,sama5d4-sckc": + "atmel,sama5d3-sckc", + "atmel,sama5d4-sckc" or + "microchip,sam9x60-sckc": at91 SCKC (Slow Clock Controller) -- #clock-cells : shall be 0. +- #clock-cells : shall be 1 for "microchip,sam9x60-sckc" otherwise shall be 0. - clocks : shall be the input parent clock phandle for the clock. Optional properties: diff --git a/Documentation/devicetree/bindings/clock/brcm,bcm63xx-clocks.txt b/Documentation/devicetree/bindings/clock/brcm,bcm63xx-clocks.txt new file mode 100644 index 000000000000..3041657e2f96 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/brcm,bcm63xx-clocks.txt @@ -0,0 +1,22 @@ +Gated Clock Controller Bindings for MIPS based BCM63XX SoCs + +Required properties: +- compatible: must be one of: + "brcm,bcm3368-clocks" + "brcm,bcm6328-clocks" + "brcm,bcm6358-clocks" + "brcm,bcm6362-clocks" + "brcm,bcm6368-clocks" + "brcm,bcm63268-clocks" + +- reg: Address and length of the register set +- #clock-cells: must be <1> + + +Example: + +clkctl: clock-controller@10000004 { + compatible = "brcm,bcm6328-clocks"; + reg = <0x10000004 0x4>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt b/Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt index b8d8ef3bdc5f..52a064c789ee 100644 --- a/Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt +++ b/Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt @@ -40,6 +40,7 @@ Optional properties: input audio clocks from host system. - ln-psia1-mclk, ln-psia2-mclk : Optional input audio clocks from external connector. + - ln-spdif-mclk : Optional input audio clock from SPDIF. - ln-spdif-clkout : Optional input audio clock from SPDIF. - ln-adat-mclk : Optional input audio clock from ADAT. - ln-pmic-32k : On board fixed clock. diff --git a/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt index 796c260c183d..d8f5c490f893 100644 --- a/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt +++ b/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt @@ -59,6 +59,7 @@ Required properties: "marvell,dove-core-clock" - for Dove SoC core clocks "marvell,kirkwood-core-clock" - for Kirkwood SoC (except mv88f6180) "marvell,mv88f6180-core-clock" - for Kirkwood MV88f6180 SoC + "marvell,mv98dx1135-core-clock" - for Kirkwood 98dx1135 SoC "marvell,mv88f5181-core-clock" - for Orion MV88F5181 SoC "marvell,mv88f5182-core-clock" - for Orion MV88F5182 SoC "marvell,mv88f5281-core-clock" - for Orion MV88F5281 SoC diff --git a/Documentation/devicetree/bindings/clock/qcom,gpucc.txt b/Documentation/devicetree/bindings/clock/qcom,gpucc.txt index 4e5215ef1acd..269afe8a757e 100644 --- a/Documentation/devicetree/bindings/clock/qcom,gpucc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,gpucc.txt @@ -2,13 +2,15 @@ Qualcomm Graphics Clock & Reset Controller Binding -------------------------------------------------- Required properties : -- compatible : shall contain "qcom,sdm845-gpucc" +- compatible : shall contain "qcom,sdm845-gpucc" or "qcom,msm8998-gpucc" - reg : shall contain base register location and length - #clock-cells : from common clock binding, shall contain 1 - #reset-cells : from common reset binding, shall contain 1 - #power-domain-cells : from generic power domain binding, shall contain 1 - clocks : shall contain the XO clock + shall contain the gpll0 out main clock (msm8998) - clock-names : shall be "xo" + shall be "gpll0" (msm8998) Example: gpucc: clock-controller@5090000 { diff --git a/Documentation/devicetree/bindings/clock/renesas,r9a06g032-sysctrl.txt b/Documentation/devicetree/bindings/clock/renesas,r9a06g032-sysctrl.txt index d60b99756bb9..aed713cf0831 100644 --- a/Documentation/devicetree/bindings/clock/renesas,r9a06g032-sysctrl.txt +++ b/Documentation/devicetree/bindings/clock/renesas,r9a06g032-sysctrl.txt @@ -13,6 +13,7 @@ Required Properties: - external (optional) RGMII_REFCLK - clock-names: Must be: clock-names = "mclk", "rtc", "jtag", "rgmii_ref_ext"; + - #power-domain-cells: Must be 0 Examples -------- @@ -27,6 +28,7 @@ Examples clocks = <&ext_mclk>, <&ext_rtc_clk>, <&ext_jtag_clk>, <&ext_rgmii_ref>; clock-names = "mclk", "rtc", "jtag", "rgmii_ref_ext"; + #power-domain-cells = <0>; }; - Other nodes can use the clocks provided by SYSCTRL as in: @@ -38,6 +40,7 @@ Examples interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; reg-shift = <2>; reg-io-width = <4>; - clocks = <&sysctrl R9A06G032_CLK_UART0>; - clock-names = "baudclk"; + clocks = <&sysctrl R9A06G032_CLK_UART0>, <&sysctrl R9A06G032_HCLK_UART0>; + clock-names = "baudclk", "apb_pclk"; + power-domains = <&sysctrl>; }; diff --git a/Documentation/devicetree/bindings/clock/silabs,si5341.txt b/Documentation/devicetree/bindings/clock/silabs,si5341.txt new file mode 100644 index 000000000000..a70c333e4cd4 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/silabs,si5341.txt @@ -0,0 +1,162 @@ +Binding for Silicon Labs Si5341 and Si5340 programmable i2c clock generator. + +Reference +[1] Si5341 Data Sheet + https://www.silabs.com/documents/public/data-sheets/Si5341-40-D-DataSheet.pdf +[2] Si5341 Reference Manual + https://www.silabs.com/documents/public/reference-manuals/Si5341-40-D-RM.pdf + +The Si5341 and Si5340 are programmable i2c clock generators with up to 10 output +clocks. The chip contains a PLL that sources 5 (or 4) multisynth clocks, which +in turn can be directed to any of the 10 (or 4) outputs through a divider. +The internal structure of the clock generators can be found in [2]. + +The driver can be used in "as is" mode, reading the current settings from the +chip at boot, in case you have a (pre-)programmed device. If the PLL is not +configured when the driver probes, it assumes the driver must fully initialize +it. + +The device type, speed grade and revision are determined runtime by probing. + +The driver currently only supports XTAL input mode, and does not support any +fancy input configurations. They can still be programmed into the chip and +the driver will leave them "as is". + +==I2C device node== + +Required properties: +- compatible: shall be one of the following: + "silabs,si5340" - Si5340 A/B/C/D + "silabs,si5341" - Si5341 A/B/C/D +- reg: i2c device address, usually 0x74 +- #clock-cells: from common clock binding; shall be set to 2. + The first value is "0" for outputs, "1" for synthesizers. + The second value is the output or synthesizer index. +- clocks: from common clock binding; list of parent clock handles, + corresponding to inputs. Use a fixed clock for the "xtal" input. + At least one must be present. +- clock-names: One of: "xtal", "in0", "in1", "in2" +- vdd-supply: Regulator node for VDD + +Optional properties: +- vdda-supply: Regulator node for VDDA +- vdds-supply: Regulator node for VDDS +- silabs,pll-m-num, silabs,pll-m-den: Numerator and denominator for PLL + feedback divider. Must be such that the PLL output is in the valid range. For + example, to create 14GHz from a 48MHz xtal, use m-num=14000 and m-den=48. Only + the fraction matters, using 3500 and 12 will deliver the exact same result. + If these are not specified, and the PLL is not yet programmed when the driver + probes, the PLL will be set to 14GHz. +- silabs,reprogram: When present, the driver will always assume the device must + be initialized, and always performs the soft-reset routine. Since this will + temporarily stop all output clocks, don't do this if the chip is generating + the CPU clock for example. +- interrupts: Interrupt for INTRb pin. +- #address-cells: shall be set to 1. +- #size-cells: shall be set to 0. + + +== Child nodes: Outputs == + +The child nodes list the output clocks. + +Each of the clock outputs can be overwritten individually by using a child node. +If a child node for a clock output is not set, the configuration remains +unchanged. + +Required child node properties: +- reg: number of clock output. + +Optional child node properties: +- vdd-supply: Regulator node for VDD for this output. The driver selects default + values for common-mode and amplitude based on the voltage. +- silabs,format: Output format, one of: + 1 = differential (defaults to LVDS levels) + 2 = low-power (defaults to HCSL levels) + 4 = LVCMOS +- silabs,common-mode: Manually override output common mode, see [2] for values +- silabs,amplitude: Manually override output amplitude, see [2] for values +- silabs,synth-master: boolean. If present, this output is allowed to change the + multisynth frequency dynamically. +- silabs,silabs,disable-high: boolean. If set, the clock output is driven HIGH + when disabled, otherwise it's driven LOW. + +==Example== + +/* 48MHz reference crystal */ +ref48: ref48M { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <48000000>; +}; + +i2c-master-node { + /* Programmable clock (for logic) */ + si5341: clock-generator@74 { + reg = <0x74>; + compatible = "silabs,si5341"; + #clock-cells = <2>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&ref48>; + clock-names = "xtal"; + + silabs,pll-m-num = <14000>; /* PLL at 14.0 GHz */ + silabs,pll-m-den = <48>; + silabs,reprogram; /* Chips are not programmed, always reset */ + + out@0 { + reg = <0>; + silabs,format = <1>; /* LVDS 3v3 */ + silabs,common-mode = <3>; + silabs,amplitude = <3>; + silabs,synth-master; + }; + + /* + * Output 6 configuration: + * LVDS 1v8 + */ + out@6 { + reg = <6>; + silabs,format = <1>; /* LVDS 1v8 */ + silabs,common-mode = <13>; + silabs,amplitude = <3>; + }; + + /* + * Output 8 configuration: + * HCSL 3v3 + */ + out@8 { + reg = <8>; + silabs,format = <2>; + silabs,common-mode = <11>; + silabs,amplitude = <3>; + }; + }; +}; + +some-video-node { + /* Standard clock bindings */ + clock-names = "pixel"; + clocks = <&si5341 0 7>; /* Output 7 */ + + /* Set output 7 to use syntesizer 3 as its parent */ + assigned-clocks = <&si5341 0 7>, <&si5341 1 3>; + assigned-clock-parents = <&si5341 1 3>; + /* Set output 7 to 148.5 MHz using a synth frequency of 594 MHz */ + assigned-clock-rates = <148500000>, <594000000>; +}; + +some-audio-node { + clock-names = "i2s-clk"; + clocks = <&si5341 0 0>; + /* + * since output 0 is a synth-master, the synth will be automatically set + * to an appropriate frequency when the audio driver requests another + * frequency. We give control over synth 2 to this output here. + */ + assigned-clocks = <&si5341 0 0>; + assigned-clock-parents = <&si5341 1 2>; +}; diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt deleted file mode 100644 index e3bd88ae456b..000000000000 --- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt +++ /dev/null @@ -1,62 +0,0 @@ -Allwinner Clock Control Unit Binding ------------------------------------- - -Required properties : -- compatible: must contain one of the following compatibles: - - "allwinner,sun4i-a10-ccu" - - "allwinner,sun5i-a10s-ccu" - - "allwinner,sun5i-a13-ccu" - - "allwinner,sun6i-a31-ccu" - - "allwinner,sun7i-a20-ccu" - - "allwinner,sun8i-a23-ccu" - - "allwinner,sun8i-a33-ccu" - - "allwinner,sun8i-a83t-ccu" - - "allwinner,sun8i-a83t-r-ccu" - - "allwinner,sun8i-h3-ccu" - - "allwinner,sun8i-h3-r-ccu" -+ - "allwinner,sun8i-r40-ccu" - - "allwinner,sun8i-v3s-ccu" - - "allwinner,sun9i-a80-ccu" - - "allwinner,sun50i-a64-ccu" - - "allwinner,sun50i-a64-r-ccu" - - "allwinner,sun50i-h5-ccu" - - "allwinner,sun50i-h6-ccu" - - "allwinner,sun50i-h6-r-ccu" - - "allwinner,suniv-f1c100s-ccu" - - "nextthing,gr8-ccu" - -- reg: Must contain the registers base address and length -- clocks: phandle to the oscillators feeding the CCU. Two are needed: - - "hosc": the high frequency oscillator (usually at 24MHz) - - "losc": the low frequency oscillator (usually at 32kHz) - On the A83T, this is the internal 16MHz oscillator divided by 512 -- clock-names: Must contain the clock names described just above -- #clock-cells : must contain 1 -- #reset-cells : must contain 1 - -For the main CCU on H6, one more clock is needed: -- "iosc": the SoC's internal frequency oscillator - -For the PRCM CCUs on A83T/H3/A64/H6, two more clocks are needed: -- "pll-periph": the SoC's peripheral PLL from the main CCU -- "iosc": the SoC's internal frequency oscillator - -Example for generic CCU: -ccu: clock@1c20000 { - compatible = "allwinner,sun8i-h3-ccu"; - reg = <0x01c20000 0x400>; - clocks = <&osc24M>, <&osc32k>; - clock-names = "hosc", "losc"; - #clock-cells = <1>; - #reset-cells = <1>; -}; - -Example for PRCM CCU: -r_ccu: clock@1f01400 { - compatible = "allwinner,sun50i-a64-r-ccu"; - reg = <0x01f01400 0x100>; - clocks = <&osc24M>, <&osc32k>, <&iosc>, <&ccu CLK_PLL_PERIPH0>; - clock-names = "hosc", "losc", "iosc", "pll-periph"; - #clock-cells = <1>; - #reset-cells = <1>; -}; diff --git a/Documentation/devicetree/bindings/csky/pmu.txt b/Documentation/devicetree/bindings/csky/pmu.txt new file mode 100644 index 000000000000..728d05ca6a1c --- /dev/null +++ b/Documentation/devicetree/bindings/csky/pmu.txt @@ -0,0 +1,38 @@ +=============================== +C-SKY Performance Monitor Units +=============================== + +C-SKY Performance Monitor is designed for ck807/ck810/ck860 SMP soc and +it could count cpu's events for helping analysis performance issues. + +============================ +PMU node bindings definition +============================ + + Description: Describes PMU + + PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: must be "csky,csky-pmu" + - interrupts + Usage: required + Value type: <u32 IRQ_TYPE_XXX> + Definition: must be pmu irq num defined by soc + - count-width + Usage: optional + Value type: <u32> + Definition: the width of pmu counter + +Examples: +--------- +#include <dt-bindings/interrupt-controller/irq.h> + + pmu: performace-monitor { + compatible = "csky,csky-pmu"; + interrupts = <23 IRQ_TYPE_EDGE_RISING>; + interrupt-parent = <&intc>; + count-width = <48>; + }; diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt index a41d280c3f9f..db680413e89c 100644 --- a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt +++ b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt @@ -12,10 +12,12 @@ following device-specific properties. Required properties: - compatible : Shall contain one or more of + - "renesas,r8a774a1-hdmi" for R8A774A1 (RZ/G2M) compatible HDMI TX - "renesas,r8a7795-hdmi" for R8A7795 (R-Car H3) compatible HDMI TX - "renesas,r8a7796-hdmi" for R8A7796 (R-Car M3-W) compatible HDMI TX - "renesas,r8a77965-hdmi" for R8A77965 (R-Car M3-N) compatible HDMI TX - - "renesas,rcar-gen3-hdmi" for the generic R-Car Gen3 compatible HDMI TX + - "renesas,rcar-gen3-hdmi" for the generic R-Car Gen3 and RZ/G2 compatible + HDMI TX When compatible with generic versions, nodes must list the SoC-specific version corresponding to the platform first, followed by the diff --git a/Documentation/devicetree/bindings/dma/8250_mtk_dma.txt b/Documentation/devicetree/bindings/dma/8250_mtk_dma.txt deleted file mode 100644 index 3fe0961bcf64..000000000000 --- a/Documentation/devicetree/bindings/dma/8250_mtk_dma.txt +++ /dev/null @@ -1,33 +0,0 @@ -* Mediatek UART APDMA Controller - -Required properties: -- compatible should contain: - * "mediatek,mt2712-uart-dma" for MT2712 compatible APDMA - * "mediatek,mt6577-uart-dma" for MT6577 and all of the above - -- reg: The base address of the APDMA register bank. - -- interrupts: A single interrupt specifier. - -- clocks : Must contain an entry for each entry in clock-names. - See ../clocks/clock-bindings.txt for details. -- clock-names: The APDMA clock for register accesses - -Examples: - - apdma: dma-controller@11000380 { - compatible = "mediatek,mt2712-uart-dma"; - reg = <0 0x11000380 0 0x400>; - interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_LOW>, - <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>, - <GIC_SPI 65 IRQ_TYPE_LEVEL_LOW>, - <GIC_SPI 66 IRQ_TYPE_LEVEL_LOW>, - <GIC_SPI 67 IRQ_TYPE_LEVEL_LOW>, - <GIC_SPI 68 IRQ_TYPE_LEVEL_LOW>, - <GIC_SPI 69 IRQ_TYPE_LEVEL_LOW>, - <GIC_SPI 70 IRQ_TYPE_LEVEL_LOW>; - clocks = <&pericfg CLK_PERI_AP_DMA>; - clock-names = "apdma"; - #dma-cells = <1>; - }; - diff --git a/Documentation/devicetree/bindings/dma/arm-pl330.txt b/Documentation/devicetree/bindings/dma/arm-pl330.txt index db7e2260f9c5..2c7fd1941abb 100644 --- a/Documentation/devicetree/bindings/dma/arm-pl330.txt +++ b/Documentation/devicetree/bindings/dma/arm-pl330.txt @@ -16,6 +16,9 @@ Optional properties: - dma-channels: contains the total number of DMA channels supported by the DMAC - dma-requests: contains the total number of DMA requests supported by the DMAC - arm,pl330-broken-no-flushp: quirk for avoiding to execute DMAFLUSHP + - resets: contains an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: must contain at least "dma", and optional is "dma-ocp". Example: diff --git a/Documentation/devicetree/bindings/dma/fsl-edma.txt b/Documentation/devicetree/bindings/dma/fsl-edma.txt index 97e213e07660..29dd3ccb1235 100644 --- a/Documentation/devicetree/bindings/dma/fsl-edma.txt +++ b/Documentation/devicetree/bindings/dma/fsl-edma.txt @@ -9,15 +9,16 @@ group, DMAMUX0 or DMAMUX1, but not both. Required properties: - compatible : - "fsl,vf610-edma" for eDMA used similar to that on Vybrid vf610 SoC + - "fsl,imx7ulp-edma" for eDMA2 used similar to that on i.mx7ulp - reg : Specifies base physical address(s) and size of the eDMA registers. The 1st region is eDMA control register's address and size. The 2nd and the 3rd regions are programmable channel multiplexing control register's address and size. - interrupts : A list of interrupt-specifiers, one for each entry in - interrupt-names. -- interrupt-names : Should contain: - "edma-tx" - the transmission interrupt - "edma-err" - the error interrupt + interrupt-names on vf610 similar SoC. But for i.mx7ulp per channel + per transmission interrupt, total 16 channel interrupt and 1 + error interrupt(located in the last), no interrupt-names list on + i.mx7ulp for clean on dts. - #dma-cells : Must be <2>. The 1st cell specifies the DMAMUX(0 for DMAMUX0 and 1 for DMAMUX1). Specific request source can only be multiplexed by specific channels @@ -28,6 +29,7 @@ Required properties: - clock-names : A list of channel group clock names. Should contain: "dmamux0" - clock name of mux0 group "dmamux1" - clock name of mux1 group + Note: No dmamux0 on i.mx7ulp, but another 'dma' clk added on i.mx7ulp. - clocks : A list of phandle and clock-specifier pairs, one for each entry in clock-names. @@ -35,6 +37,10 @@ Optional properties: - big-endian: If present registers and hardware scatter/gather descriptors of the eDMA are implemented in big endian mode, otherwise in little mode. +- interrupt-names : Should contain the below on vf610 similar SoC but not used + on i.mx7ulp similar SoC: + "edma-tx" - the transmission interrupt + "edma-err" - the error interrupt Examples: @@ -52,8 +58,36 @@ edma0: dma-controller@40018000 { clock-names = "dmamux0", "dmamux1"; clocks = <&clks VF610_CLK_DMAMUX0>, <&clks VF610_CLK_DMAMUX1>; -}; +}; /* vf610 */ +edma1: dma-controller@40080000 { + #dma-cells = <2>; + compatible = "fsl,imx7ulp-edma"; + reg = <0x40080000 0x2000>, + <0x40210000 0x1000>; + dma-channels = <32>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>, + /* last is eDMA2-ERR interrupt */ + <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "dma", "dmamux0"; + clocks = <&pcc2 IMX7ULP_CLK_DMA1>, + <&pcc2 IMX7ULP_CLK_DMA_MUX1>; +}; /* i.mx7ulp */ * DMA clients DMA client drivers that uses the DMA function must use the format described diff --git a/Documentation/devicetree/bindings/dma/fsl-qdma.txt b/Documentation/devicetree/bindings/dma/fsl-qdma.txt index 6a0ff9059e72..da371c4d406c 100644 --- a/Documentation/devicetree/bindings/dma/fsl-qdma.txt +++ b/Documentation/devicetree/bindings/dma/fsl-qdma.txt @@ -7,6 +7,7 @@ Required properties: - compatible: Must be one of "fsl,ls1021a-qdma": for LS1021A Board + "fsl,ls1028a-qdma": for LS1028A Board "fsl,ls1043a-qdma": for ls1043A Board "fsl,ls1046a-qdma": for ls1046A Board - reg: Should contain the register's base address and length. diff --git a/Documentation/devicetree/bindings/dma/mtk-uart-apdma.txt b/Documentation/devicetree/bindings/dma/mtk-uart-apdma.txt new file mode 100644 index 000000000000..5d6f98c43e3d --- /dev/null +++ b/Documentation/devicetree/bindings/dma/mtk-uart-apdma.txt @@ -0,0 +1,54 @@ +* Mediatek UART APDMA Controller + +Required properties: +- compatible should contain: + * "mediatek,mt2712-uart-dma" for MT2712 compatible APDMA + * "mediatek,mt6577-uart-dma" for MT6577 and all of the above + +- reg: The base address of the APDMA register bank. + +- interrupts: A single interrupt specifier. + One interrupt per dma-requests, or 8 if no dma-requests property is present + +- dma-requests: The number of DMA channels + +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: The APDMA clock for register accesses + +- mediatek,dma-33bits: Present if the DMA requires support + +Examples: + + apdma: dma-controller@11000400 { + compatible = "mediatek,mt2712-uart-dma"; + reg = <0 0x11000400 0 0x80>, + <0 0x11000480 0 0x80>, + <0 0x11000500 0 0x80>, + <0 0x11000580 0 0x80>, + <0 0x11000600 0 0x80>, + <0 0x11000680 0 0x80>, + <0 0x11000700 0 0x80>, + <0 0x11000780 0 0x80>, + <0 0x11000800 0 0x80>, + <0 0x11000880 0 0x80>, + <0 0x11000900 0 0x80>, + <0 0x11000980 0 0x80>; + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 105 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 106 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 107 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 108 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 109 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 110 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 111 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 112 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 113 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 114 IRQ_TYPE_LEVEL_LOW>; + dma-requests = <12>; + clocks = <&pericfg CLK_PERI_AP_DMA>; + clock-names = "apdma"; + mediatek,dma-33bits; + #dma-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/dma/sun6i-dma.txt b/Documentation/devicetree/bindings/dma/sun6i-dma.txt index 7fccc20d8331..cae31f4e77ba 100644 --- a/Documentation/devicetree/bindings/dma/sun6i-dma.txt +++ b/Documentation/devicetree/bindings/dma/sun6i-dma.txt @@ -28,12 +28,17 @@ Example: }; ------------------------------------------------------------------------------ -For A64 DMA controller: +For A64 and H6 DMA controller: Required properties: -- compatible: "allwinner,sun50i-a64-dma" +- compatible: Must be one of + "allwinner,sun50i-a64-dma" + "allwinner,sun50i-h6-dma" - dma-channels: Number of DMA channels supported by the controller. Refer to Documentation/devicetree/bindings/dma/dma.txt +- clocks: In addition to parent AHB clock, it should also contain mbus + clock (H6 only) +- clock-names: Should contain "bus" and "mbus" (H6 only) - all properties above, i.e. reg, interrupts, clocks, resets and #dma-cells Optional properties: diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt b/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt index e5ad3b2afe17..9b298edec5b2 100644 --- a/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt +++ b/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt @@ -17,6 +17,7 @@ Required properties: * which must be preceded by one of the following vendor specifics: + "allwinner,sun50i-h6-mali" + "amlogic,meson-gxm-mali" + + "samsung,exynos5433-mali" + "rockchip,rk3288-mali" + "rockchip,rk3399-mali" diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt index ae63f09fda7d..b352a6851a06 100644 --- a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt +++ b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt @@ -17,6 +17,7 @@ Required properties: + amlogic,meson8b-mali + amlogic,meson-gxbb-mali + amlogic,meson-gxl-mali + + samsung,exynos4210-mali + rockchip,rk3036-mali + rockchip,rk3066-mali + rockchip,rk3188-mali diff --git a/Documentation/devicetree/bindings/hwlock/omap-hwspinlock.txt b/Documentation/devicetree/bindings/hwlock/omap-hwspinlock.txt index 2c9804f4f4ac..8d365f89694c 100644 --- a/Documentation/devicetree/bindings/hwlock/omap-hwspinlock.txt +++ b/Documentation/devicetree/bindings/hwlock/omap-hwspinlock.txt @@ -1,12 +1,16 @@ -OMAP4+ HwSpinlock Driver -======================== +TI HwSpinlock for OMAP and K3 based SoCs +========================================= Required properties: -- compatible: Should be "ti,omap4-hwspinlock" for - OMAP44xx, OMAP54xx, AM33xx, AM43xx, DRA7xx SoCs +- compatible: Should be one of the following, + "ti,omap4-hwspinlock" for + OMAP44xx, OMAP54xx, AM33xx, AM43xx, DRA7xx SoCs + "ti,am654-hwspinlock" for + K3 AM65x and J721E SoCs - reg: Contains the hwspinlock module register address space (base address and length) - ti,hwmods: Name of the hwmod associated with the hwspinlock device + (for OMAP architecture based SoCs only) - #hwlock-cells: Should be 1. The OMAP hwspinlock users will use a 0-indexed relative hwlock number as the argument specifier value for requesting a specific hwspinlock @@ -17,10 +21,21 @@ Please look at the generic hwlock binding for usage information for consumers, Example: -/* OMAP4 */ +1. OMAP4 SoCs hwspinlock: spinlock@4a0f6000 { compatible = "ti,omap4-hwspinlock"; reg = <0x4a0f6000 0x1000>; ti,hwmods = "spinlock"; #hwlock-cells = <1>; }; + +2. AM65x SoCs and J721E SoCs +&cbass_main { + cbass_main_navss: interconnect0 { + hwspinlock: spinlock@30e00000 { + compatible = "ti,am654-hwspinlock"; + reg = <0x00 0x30e00000 0x00 0x1000>; + #hwlock-cells = <1>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt b/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt index 496125c6bfb7..507b737612ea 100644 --- a/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt +++ b/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt @@ -5,6 +5,7 @@ Required properties: - compatible: should be one of the following string: "allwinner,sun4i-a10-lradc-keys" "allwinner,sun8i-a83t-r-lradc" + "allwinner,sun50i-a64-lradc", "allwinner,sun8i-a83t-r-lradc" - reg: mmio address range of the chip - interrupts: interrupt to which the chip is connected - vref-supply: powersupply for the lradc reference voltage diff --git a/Documentation/devicetree/bindings/misc/fsl,dpaa2-console.txt b/Documentation/devicetree/bindings/misc/fsl,dpaa2-console.txt new file mode 100644 index 000000000000..1442ba5d2d98 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/fsl,dpaa2-console.txt @@ -0,0 +1,11 @@ +DPAA2 console support + +Required properties: + + - compatible + Value type: <string> + Definition: Must be "fsl,dpaa2-console". + - reg + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the region where the MCFBA + (MC firmware base address) register can be found. diff --git a/Documentation/devicetree/bindings/net/can/rcar_can.txt b/Documentation/devicetree/bindings/net/can/rcar_can.txt index 9936b9ee67c3..b463e1268ac4 100644 --- a/Documentation/devicetree/bindings/net/can/rcar_can.txt +++ b/Documentation/devicetree/bindings/net/can/rcar_can.txt @@ -6,6 +6,7 @@ Required properties: "renesas,can-r8a7744" if CAN controller is a part of R8A7744 SoC. "renesas,can-r8a7745" if CAN controller is a part of R8A7745 SoC. "renesas,can-r8a774a1" if CAN controller is a part of R8A774A1 SoC. + "renesas,can-r8a774c0" if CAN controller is a part of R8A774C0 SoC. "renesas,can-r8a7778" if CAN controller is a part of R8A7778 SoC. "renesas,can-r8a7779" if CAN controller is a part of R8A7779 SoC. "renesas,can-r8a7790" if CAN controller is a part of R8A7790 SoC. @@ -27,13 +28,8 @@ Required properties: - reg: physical base address and size of the R-Car CAN register map. - interrupts: interrupt specifier for the sole interrupt. -- clocks: phandles and clock specifiers for 2 CAN clock inputs for RZ/G2 - devices. - phandles and clock specifiers for 3 CAN clock inputs for every other - SoC. -- clock-names: 2 clock input name strings for RZ/G2: "clkp1", "can_clk". - 3 clock input name strings for every other SoC: "clkp1", "clkp2", - "can_clk". +- clocks: phandles and clock specifiers for 3 CAN clock inputs. +- clock-names: 3 clock input name strings: "clkp1", "clkp2", and "can_clk". - pinctrl-0: pin control group to be used for this controller. - pinctrl-names: must be "default". @@ -49,8 +45,7 @@ using the below properties: Optional properties: - renesas,can-clock-select: R-Car CAN Clock Source Select. Valid values are: <0x0> (default) : Peripheral clock (clkp1) - <0x1> : Peripheral clock (clkp2) (not supported by - RZ/G2 devices) + <0x1> : Peripheral clock (clkp2) <0x3> : External input clock Example diff --git a/Documentation/devicetree/bindings/net/can/rcar_canfd.txt b/Documentation/devicetree/bindings/net/can/rcar_canfd.txt index ac71daa46195..32f051f6d338 100644 --- a/Documentation/devicetree/bindings/net/can/rcar_canfd.txt +++ b/Documentation/devicetree/bindings/net/can/rcar_canfd.txt @@ -3,11 +3,14 @@ Renesas R-Car CAN FD controller Device Tree Bindings Required properties: - compatible: Must contain one or more of the following: - - "renesas,rcar-gen3-canfd" for R-Car Gen3 compatible controller. + - "renesas,rcar-gen3-canfd" for R-Car Gen3 and RZ/G2 compatible controllers. + - "renesas,r8a774c0-canfd" for R8A774C0 (RZ/G2E) compatible controller. - "renesas,r8a7795-canfd" for R8A7795 (R-Car H3) compatible controller. - "renesas,r8a7796-canfd" for R8A7796 (R-Car M3-W) compatible controller. + - "renesas,r8a77965-canfd" for R8A77965 (R-Car M3-N) compatible controller. - "renesas,r8a77970-canfd" for R8A77970 (R-Car V3M) compatible controller. - "renesas,r8a77980-canfd" for R8A77980 (R-Car V3H) compatible controller. + - "renesas,r8a77990-canfd" for R8A77990 (R-Car E3) compatible controller. When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first, followed by the @@ -26,12 +29,13 @@ The name of the child nodes are "channel0" and "channel1" respectively. Each child node supports the "status" property only, which is used to enable/disable the respective channel. -Required properties for "renesas,r8a7795-canfd" and "renesas,r8a7796-canfd" +Required properties for "renesas,r8a774c0-canfd", "renesas,r8a7795-canfd", +"renesas,r8a7796-canfd", "renesas,r8a77965-canfd", and "renesas,r8a77990-canfd" compatible: -In R8A7795 and R8A7796 SoCs, canfd clock is a div6 clock and can be used by both -CAN and CAN FD controller at the same time. It needs to be scaled to maximum -frequency if any of these controllers use it. This is done using the below -properties: +In R8A774C0, R8A7795, R8A7796, R8A77965, and R8A77990 SoCs, canfd clock is a +div6 clock and can be used by both CAN and CAN FD controller at the same time. +It needs to be scaled to maximum frequency if any of these controllers use it. +This is done using the below properties: - assigned-clocks: phandle of canfd clock. - assigned-clock-rates: maximum frequency of this clock. diff --git a/Documentation/devicetree/bindings/phy/phy-bindings.txt b/Documentation/devicetree/bindings/phy/phy-bindings.txt index a403b81d0679..c4eb38902533 100644 --- a/Documentation/devicetree/bindings/phy/phy-bindings.txt +++ b/Documentation/devicetree/bindings/phy/phy-bindings.txt @@ -1,5 +1,5 @@ This document explains only the device tree data binding. For general -information about PHY subsystem refer to Documentation/phy.txt +information about PHY subsystem refer to Documentation/driver-api/phy/phy.rst PHY device node =============== diff --git a/Documentation/devicetree/bindings/phy/phy-pxa-usb.txt b/Documentation/devicetree/bindings/phy/phy-pxa-usb.txt index 93fc09c12954..d80e36a77ec5 100644 --- a/Documentation/devicetree/bindings/phy/phy-pxa-usb.txt +++ b/Documentation/devicetree/bindings/phy/phy-pxa-usb.txt @@ -15,4 +15,4 @@ Example: }; This document explains the device tree binding. For general -information about PHY subsystem refer to Documentation/phy.txt +information about PHY subsystem refer to Documentation/driver-api/phy/phy.rst diff --git a/Documentation/devicetree/bindings/power/qcom,rpmpd.txt b/Documentation/devicetree/bindings/power/qcom,rpmpd.txt index 980e5413d18f..eb35b22f9e23 100644 --- a/Documentation/devicetree/bindings/power/qcom,rpmpd.txt +++ b/Documentation/devicetree/bindings/power/qcom,rpmpd.txt @@ -6,6 +6,8 @@ which then translates it into a corresponding voltage on a rail Required Properties: - compatible: Should be one of the following * qcom,msm8996-rpmpd: RPM Power domain for the msm8996 family of SoC + * qcom,msm8998-rpmpd: RPM Power domain for the msm8998 family of SoC + * qcom,qcs404-rpmpd: RPM Power domain for the qcs404 family of SoC * qcom,sdm845-rpmhpd: RPMh Power domain for the sdm845 family of SoC - #power-domain-cells: number of cells in Power domain specifier must be 1. diff --git a/Documentation/devicetree/bindings/pwm/allwinner,sun4i-a10-pwm.yaml b/Documentation/devicetree/bindings/pwm/allwinner,sun4i-a10-pwm.yaml new file mode 100644 index 000000000000..0ac52f83a58c --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/allwinner,sun4i-a10-pwm.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pwm/allwinner,sun4i-a10-pwm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 PWM Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + "#pwm-cells": + const: 3 + + compatible: + oneOf: + - const: allwinner,sun4i-a10-pwm + - const: allwinner,sun5i-a10s-pwm + - const: allwinner,sun5i-a13-pwm + - const: allwinner,sun7i-a20-pwm + - const: allwinner,sun8i-h3-pwm + - items: + - const: allwinner,sun8i-a83t-pwm + - const: allwinner,sun8i-h3-pwm + - items: + - const: allwinner,sun50i-a64-pwm + - const: allwinner,sun5i-a13-pwm + - items: + - const: allwinner,sun50i-h5-pwm + - const: allwinner,sun5i-a13-pwm + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + +required: + - "#pwm-cells" + - compatible + - reg + - clocks + +additionalProperties: false + +examples: + - | + pwm: pwm@1c20e00 { + compatible = "allwinner,sun7i-a20-pwm"; + reg = <0x01c20e00 0xc>; + clocks = <&osc24M>; + #pwm-cells = <3>; + }; + +... diff --git a/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt b/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt deleted file mode 100644 index 2a1affbff45e..000000000000 --- a/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt +++ /dev/null @@ -1,24 +0,0 @@ -Allwinner sun4i and sun7i SoC PWM controller - -Required properties: - - compatible: should be one of: - - "allwinner,sun4i-a10-pwm" - - "allwinner,sun5i-a10s-pwm" - - "allwinner,sun5i-a13-pwm" - - "allwinner,sun7i-a20-pwm" - - "allwinner,sun8i-h3-pwm" - - "allwinner,sun50i-a64-pwm", "allwinner,sun5i-a13-pwm" - - "allwinner,sun50i-h5-pwm", "allwinner,sun5i-a13-pwm" - - reg: physical base address and length of the controller's registers - - #pwm-cells: should be 3. See pwm.txt in this directory for a description of - the cells format. - - clocks: From common clock binding, handle to the parent clock. - -Example: - - pwm: pwm@1c20e00 { - compatible = "allwinner,sun7i-a20-pwm"; - reg = <0x01c20e00 0xc>; - clocks = <&osc24M>; - #pwm-cells = <3>; - }; diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,adsp-pil.txt b/Documentation/devicetree/bindings/remoteproc/qcom,hexagon-v56.txt index 66af2c30944f..1337a3d93d35 100644 --- a/Documentation/devicetree/bindings/remoteproc/qcom,adsp-pil.txt +++ b/Documentation/devicetree/bindings/remoteproc/qcom,hexagon-v56.txt @@ -1,12 +1,13 @@ -Qualcomm Technology Inc. ADSP Peripheral Image Loader +Qualcomm Technology Inc. Hexagon v56 Peripheral Image Loader This document defines the binding for a component that loads and boots firmware -on the Qualcomm Technology Inc. ADSP Hexagon core. +on the Qualcomm Technology Inc. Hexagon v56 core. - compatible: Usage: required Value type: <string> Definition: must be one of: + "qcom,qcs404-cdsp-pil", "qcom,sdm845-adsp-pil" - reg: @@ -28,10 +29,11 @@ on the Qualcomm Technology Inc. ADSP Hexagon core. - clocks: Usage: required Value type: <prop-encoded-array> - Definition: List of 8 phandle and clock specifier pairs for the adsp. + Definition: List of phandles and clock specifier pairs for the Hexagon, + per clock-names below. - clock-names: - Usage: required + Usage: required for SDM845 ADSP Value type: <stringlist> Definition: List of clock input name strings sorted in the same order as the clocks property. Definition must have @@ -39,6 +41,14 @@ on the Qualcomm Technology Inc. ADSP Hexagon core. "lpass_ahbm_aon_cbcr", "qdsp6ss_xo", "qdsp6ss_sleep" and "qdsp6ss_core". +- clock-names: + Usage: required for QCS404 CDSP + Value type: <stringlist> + Definition: List of clock input name strings sorted in the same + order as the clocks property. Definition must have + "xo", "sway", "tbu", "bimc", "ahb_aon", "q6ss_slave", + "q6ss_master", "q6_axim". + - power-domains: Usage: required Value type: <phandle> @@ -47,28 +57,33 @@ on the Qualcomm Technology Inc. ADSP Hexagon core. - resets: Usage: required Value type: <phandle> - Definition: reference to the list of 2 reset-controller for the adsp. + Definition: reference to the list of resets for the Hexagon. - reset-names: - Usage: required + Usage: required for SDM845 ADSP Value type: <stringlist> Definition: must be "pdc_sync" and "cc_lpass" +- reset-names: + Usage: required for QCS404 CDSP + Value type: <stringlist> + Definition: must be "restart" + - qcom,halt-regs: Usage: required Value type: <prop-encoded-array> Definition: a phandle reference to a syscon representing TCSR followed - by the offset within syscon for lpass halt register. + by the offset within syscon for Hexagon halt register. - memory-region: Usage: required Value type: <phandle> - Definition: reference to the reserved-memory for the ADSP + Definition: reference to the reserved-memory for the firmware - qcom,smem-states: Usage: required Value type: <phandle> - Definition: reference to the smem state for requesting the ADSP to + Definition: reference to the smem state for requesting the Hexagon to shut down - qcom,smem-state-names: @@ -79,7 +94,7 @@ on the Qualcomm Technology Inc. ADSP Hexagon core. = SUBNODES The adsp node may have an subnode named "glink-edge" that describes the -communication edge, channels and devices related to the ADSP. +communication edge, channels and devices related to the Hexagon. See ../soc/qcom/qcom,glink.txt for details on how to describe these. = EXAMPLE diff --git a/Documentation/devicetree/bindings/remoteproc/stm32-rproc.txt b/Documentation/devicetree/bindings/remoteproc/stm32-rproc.txt new file mode 100644 index 000000000000..5fa915a4b736 --- /dev/null +++ b/Documentation/devicetree/bindings/remoteproc/stm32-rproc.txt @@ -0,0 +1,63 @@ +STMicroelectronics STM32 Remoteproc +----------------------------------- +This document defines the binding for the remoteproc component that loads and +boots firmwares on the ST32MP family chipset. + +Required properties: +- compatible: Must be "st,stm32mp1-m4" +- reg: Address ranges of the RETRAM and MCU SRAM memories used by the + remote processor. +- resets: Reference to a reset controller asserting the remote processor. +- st,syscfg-holdboot: Reference to the system configuration which holds the + remote processor reset hold boot + 1st cell: phandle of syscon block + 2nd cell: register offset containing the hold boot setting + 3rd cell: register bitmask for the hold boot field +- st,syscfg-tz: Reference to the system configuration which holds the RCC trust + zone mode + 1st cell: phandle to syscon block + 2nd cell: register offset containing the RCC trust zone mode setting + 3rd cell: register bitmask for the RCC trust zone mode bit + +Optional properties: +- interrupts: Should contain the watchdog interrupt +- mboxes: This property is required only if the rpmsg/virtio functionality + is used. List of phandle and mailbox channel specifiers: + - a channel (a) used to communicate through virtqueues with the + remote proc. + Bi-directional channel: + - from local to remote = send message + - from remote to local = send message ack + - a channel (b) working the opposite direction of channel (a) + - a channel (c) used by the local proc to notify the remote proc + that it is about to be shut down. + Unidirectional channel: + - from local to remote, where ACK from the remote means + that it is ready for shutdown +- mbox-names: This property is required if the mboxes property is used. + - must be "vq0" for channel (a) + - must be "vq1" for channel (b) + - must be "shutdown" for channel (c) +- memory-region: List of phandles to the reserved memory regions associated with + the remoteproc device. This is variable and describes the + memories shared with the remote processor (eg: remoteproc + firmware and carveouts, rpmsg vrings, ...). + (see ../reserved-memory/reserved-memory.txt) +- st,syscfg-pdds: Reference to the system configuration which holds the remote + processor deep sleep setting + 1st cell: phandle to syscon block + 2nd cell: register offset containing the deep sleep setting + 3rd cell: register bitmask for the deep sleep bit +- st,auto-boot: If defined, when remoteproc is probed, it loads the default + firmware and starts the remote processor. + +Example: + m4_rproc: m4@10000000 { + compatible = "st,stm32mp1-m4"; + reg = <0x10000000 0x40000>, + <0x30000000 0x40000>, + <0x38000000 0x10000>; + resets = <&rcc MCU_R>; + st,syscfg-holdboot = <&rcc 0x10C 0x1>; + st,syscfg-tz = <&rcc 0x000 0x1>; + }; diff --git a/Documentation/devicetree/bindings/reset/bitmain,bm1880-reset.txt b/Documentation/devicetree/bindings/reset/bitmain,bm1880-reset.txt new file mode 100644 index 000000000000..a6f8455ae6c4 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/bitmain,bm1880-reset.txt @@ -0,0 +1,18 @@ +Bitmain BM1880 SoC Reset Controller +=================================== + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: +- compatible: Should be "bitmain,bm1880-reset" +- reg: Offset and length of reset controller space in SCTRL. +- #reset-cells: Must be 1. + +Example: + + rst: reset-controller@c00 { + compatible = "bitmain,bm1880-reset"; + reg = <0xc00 0x8>; + #reset-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt index 2ecf33815d18..13e095182db4 100644 --- a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt +++ b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt @@ -45,6 +45,6 @@ Example: }; -For list of all valid reset indicies see +For list of all valid reset indices see <dt-bindings/reset/imx7-reset.h> for i.MX7 and <dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ diff --git a/Documentation/devicetree/bindings/rtc/allwinner,sun4i-a10-rtc.yaml b/Documentation/devicetree/bindings/rtc/allwinner,sun4i-a10-rtc.yaml new file mode 100644 index 000000000000..46d69c32b89b --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/allwinner,sun4i-a10-rtc.yaml @@ -0,0 +1,43 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/rtc/allwinner,sun4i-a10-rtc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 RTC Device Tree Bindings + +allOf: + - $ref: "rtc.yaml#" + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + compatible: + enum: + - allwinner,sun4i-a10-rtc + - allwinner,sun7i-a20-rtc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + rtc: rtc@1c20d00 { + compatible = "allwinner,sun4i-a10-rtc"; + reg = <0x01c20d00 0x20>; + interrupts = <24>; + }; + +... diff --git a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml new file mode 100644 index 000000000000..924622f39c44 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml @@ -0,0 +1,134 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/rtc/allwinner,sun6i-a31-rtc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A31 RTC Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + "#clock-cells": + const: 1 + + compatible: + oneOf: + - const: allwinner,sun6i-a31-rtc + - const: allwinner,sun8i-a23-rtc + - const: allwinner,sun8i-h3-rtc + - const: allwinner,sun8i-r40-rtc + - const: allwinner,sun8i-v3-rtc + - const: allwinner,sun50i-h5-rtc + - items: + - const: allwinner,sun50i-a64-rtc + - const: allwinner,sun8i-h3-rtc + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + maxItems: 2 + items: + - description: RTC Alarm 0 + - description: RTC Alarm 1 + + clocks: + maxItems: 1 + + clock-output-names: + minItems: 1 + maxItems: 3 + description: + The RTC provides up to three clocks + - the Low Frequency Oscillator or LOSC, at index 0, + - the Low Frequency Oscillator External output (X32KFOUT in + the datasheet), at index 1, + - the Internal Oscillator, at index 2. + +allOf: + - $ref: "rtc.yaml#" + - if: + properties: + compatible: + contains: + const: allwinner,sun6i-a31-rtc + + then: + properties: + clock-output-names: + minItems: 1 + maxItems: 1 + + - if: + properties: + compatible: + contains: + enum: + - allwinner,sun8i-a23-rtc + - allwinner,sun8i-r40-rtc + - allwinner,sun8i-v3-rtc + + then: + properties: + clock-output-names: + minItems: 2 + maxItems: 2 + + - if: + properties: + compatible: + contains: + enum: + - allwinner,sun8i-h3-rtc + - allwinner,sun50i-h5-rtc + + then: + properties: + clock-output-names: + minItems: 3 + maxItems: 3 + + - if: + properties: + compatible: + contains: + const: allwinner,sun8i-r40-rtc + + then: + properties: + interrupts: + minItems: 1 + maxItems: 1 + + else: + properties: + interrupts: + minItems: 2 + maxItems: 2 + +required: + - "#clock-cells" + - compatible + - reg + - interrupts + - clocks + - clock-output-names + +additionalProperties: false + +examples: + - | + rtc: rtc@1f00000 { + compatible = "allwinner,sun6i-a31-rtc"; + reg = <0x01f00000 0x400>; + interrupts = <0 40 4>, <0 41 4>; + clock-output-names = "osc32k"; + clocks = <&ext_osc32k>; + #clock-cells = <1>; + }; + +... diff --git a/Documentation/devicetree/bindings/rtc/rtc.txt b/Documentation/devicetree/bindings/rtc/rtc.txt index a97fc6a9a75e..b8d36fce5e2d 100644 --- a/Documentation/devicetree/bindings/rtc/rtc.txt +++ b/Documentation/devicetree/bindings/rtc/rtc.txt @@ -1,72 +1 @@ -Generic device tree bindings for Real Time Clock devices -======================================================== - -This document describes generic bindings which can be used to describe Real Time -Clock devices in a device tree. - -Required properties -------------------- - -- compatible : name of RTC device following generic names recommended practice. - -For other required properties e.g. to describe register sets, -clocks, etc. check the binding documentation of the specific driver. - -Optional properties -------------------- - -- start-year : if provided, the default hardware range supported by the RTC is - shifted so the first usable year is the specified one. - -The following properties may not be supported by all drivers. However, if a -driver wants to support one of the below features, it should adapt the bindings -below. -- trickle-resistor-ohms : Selected resistor for trickle charger. Should be given - if trickle charger should be enabled -- trickle-diode-disable : Do not use internal trickle charger diode Should be - given if internal trickle charger diode should be - disabled -- wakeup-source : Enables wake up of host system on alarm -- quartz-load-femtofarads : The capacitive load of the quartz(x-tal), - expressed in femto Farad (fF). - The default value shall be listed (if optional), - and likewise all valid values. - -Trivial RTCs ------------- - -This is a list of trivial RTC devices that have simple device tree -bindings, consisting only of a compatible field, an address and -possibly an interrupt line. - - -Compatible Vendor / Chip -========== ============= -abracon,abb5zes3 AB-RTCMC-32.768kHz-B5ZE-S3: Real Time Clock/Calendar Module with I2C Interface -abracon,abeoz9 AB-RTCMC-32.768kHz-EOZ9: Real Time Clock/Calendar Module with I2C Interface -dallas,ds1374 I2C, 32-Bit Binary Counter Watchdog RTC with Trickle Charger and Reset Input/Output -dallas,ds1672 Dallas DS1672 Real-time Clock -dallas,ds3232 Extremely Accurate I²C RTC with Integrated Crystal and SRAM -epson,rx8010 I2C-BUS INTERFACE REAL TIME CLOCK MODULE -epson,rx8571 I2C-BUS INTERFACE REAL TIME CLOCK MODULE with Battery Backed RAM -epson,rx8581 I2C-BUS INTERFACE REAL TIME CLOCK MODULE -emmicro,em3027 EM Microelectronic EM3027 Real-time Clock -isil,isl1208 Intersil ISL1208 Low Power RTC with Battery Backed SRAM -isil,isl1218 Intersil ISL1218 Low Power RTC with Battery Backed SRAM -isil,isl12022 Intersil ISL12022 Real-time Clock -microcrystal,rv3028 Real Time Clock Module with I2C-Bus -microcrystal,rv3029 Real Time Clock Module with I2C-Bus -microcrystal,rv8523 Real Time Clock -nxp,pcf2127 Real-time clock -nxp,pcf2129 Real-time clock -nxp,pcf8563 Real-time clock/calendar -pericom,pt7c4338 Real-time Clock Module -ricoh,r2025sd I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC -ricoh,r2221tl I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC -ricoh,rs5c372a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC -ricoh,rs5c372b I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC -ricoh,rv5c386 I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC -ricoh,rv5c387a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC -sii,s35390a 2-wire CMOS real-time clock -whwave,sd3078 I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC -xircom,x1205 Xircom X1205 I2C RTC +This file has been moved to rtc.yaml. diff --git a/Documentation/devicetree/bindings/rtc/rtc.yaml b/Documentation/devicetree/bindings/rtc/rtc.yaml new file mode 100644 index 000000000000..ee237b2ed66a --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/rtc.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/rtc/rtc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: RTC Generic Binding + +maintainers: + - Alexandre Belloni <alexandre.belloni@bootlin.com> + +description: | + This document describes generic bindings which can be used to + describe Real Time Clock devices in a device tree. + +properties: + $nodename: + pattern: "^rtc(@.*|-[0-9a-f])*$" + + quartz-load-femtofarads: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + The capacitive load of the quartz(x-tal), expressed in femto + Farad (fF). The default value shall be listed (if optional), + and likewise all valid values. + + start-year: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + If provided, the default hardware range supported by the RTC is + shifted so the first usable year is the specified one. + + trickle-diode-disable: + $ref: /schemas/types.yaml#/definitions/flag + description: + Do not use internal trickle charger diode. Should be given if + internal trickle charger diode should be disabled. + + trickle-resistor-ohms: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Selected resistor for trickle charger. Should be given + if trickle charger should be enabled. + + wakeup-source: + $ref: /schemas/types.yaml#/definitions/flag + description: + Enables wake up of host system on alarm. + +... diff --git a/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt b/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt deleted file mode 100644 index 6b732c41392b..000000000000 --- a/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt +++ /dev/null @@ -1,46 +0,0 @@ -* sun6i Real Time Clock - -RTC controller for the Allwinner A31 - -Required properties: -- compatible : Should be one of the following combinations: - - "allwinner,sun6i-a31-rtc" - - "allwinner,sun8i-a23-rtc" - - "allwinner,sun8i-h3-rtc" - - "allwinner,sun8i-r40-rtc", "allwinner,sun8i-h3-rtc" - - "allwinner,sun8i-v3-rtc" - - "allwinner,sun50i-a64-rtc", "allwinner,sun8i-h3-rtc" - - "allwinner,sun50i-h5-rtc" - - Where there are two or more compatible strings, this - denotes the hardware covered by the most specific one - is backward-compatible with the latter ones, and the - implementation for the latter ones can be used, albeit - with reduced functionality. - -- reg : physical base address of the controller and length of - memory mapped region. -- interrupts : IRQ lines for the RTC alarm 0 and alarm 1, in that order. - -Required properties for new device trees -- clocks : phandle to the 32kHz external oscillator -- clock-output-names : names of up to three clock outputs. See below. -- #clock-cells : must be equal to 1. - -The RTC provides the following clocks at the given indices: -- 0: LOSC -- 1: LOSC external output, known as X32KFOUT in the datasheet. - This clock is not available on the A31 and is deprecated for old - device trees still using the "allwinner,sun6i-a31-rtc" compatible. -- 2: InternalOSC, or internal RC oscillator (A64/H3/H5 only) - -Example: - -rtc: rtc@1f00000 { - compatible = "allwinner,sun6i-a31-rtc"; - reg = <0x01f00000 0x400>; - interrupts = <0 40 4>, <0 41 4>; - clock-output-names = "osc32k"; - clocks = <&ext_osc32k>; - #clock-cells = <1>; -}; diff --git a/Documentation/devicetree/bindings/rtc/sunxi-rtc.txt b/Documentation/devicetree/bindings/rtc/sunxi-rtc.txt deleted file mode 100644 index 4a8d79c1cf08..000000000000 --- a/Documentation/devicetree/bindings/rtc/sunxi-rtc.txt +++ /dev/null @@ -1,17 +0,0 @@ -* sun4i/sun7i Real Time Clock - -RTC controller for the Allwinner A10/A20 - -Required properties: -- compatible : Should be "allwinner,sun4i-a10-rtc" or "allwinner,sun7i-a20-rtc" -- reg: physical base address of the controller and length of memory mapped - region. -- interrupts: IRQ line for the RTC. - -Example: - -rtc: rtc@1c20d00 { - compatible = "allwinner,sun4i-a10-rtc"; - reg = <0x01c20d00 0x20>; - interrupts = <24>; -}; diff --git a/Documentation/devicetree/bindings/rtc/trivial-rtc.yaml b/Documentation/devicetree/bindings/rtc/trivial-rtc.yaml new file mode 100644 index 000000000000..0c12ce9a9b45 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/trivial-rtc.yaml @@ -0,0 +1,92 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/rtc/trivial-rtc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Trivial RTCs + +maintainers: + - Alexandre Belloni <alexandre.belloni@bootlin.com> + +description: | + This is a list of trivial RTC devices that have simple device tree + bindings, consisting only of a compatible field, an address and + possibly an interrupt line. + +allOf: + - $ref: "rtc.yaml#" + +properties: + compatible: + enum: + # AB-RTCMC-32.768kHz-B5ZE-S3: Real Time Clock/Calendar Module with I2C Interface + - abracon,abb5zes3 + # AB-RTCMC-32.768kHz-EOZ9: Real Time Clock/Calendar Module with I2C Interface + - abracon,abeoz9 + # I2C, 32-Bit Binary Counter Watchdog RTC with Trickle Charger and Reset Input/Output + - dallas,ds1374 + # Dallas DS1672 Real-time Clock + - dallas,ds1672 + # Extremely Accurate I²C RTC with Integrated Crystal and SRAM + - dallas,ds3232 + # I2C-BUS INTERFACE REAL TIME CLOCK MODULE + - epson,rx8010 + # I2C-BUS INTERFACE REAL TIME CLOCK MODULE with Battery Backed RAM + - epson,rx8571 + # I2C-BUS INTERFACE REAL TIME CLOCK MODULE + - epson,rx8581 + # Intersil ISL1208 Low Power RTC with Battery Backed SRAM + - isil,isl1208 + # Intersil ISL1218 Low Power RTC with Battery Backed SRAM + - isil,isl1218 + # Intersil ISL12022 Real-time Clock + - isil,isl12022 + # Real Time Clock Module with I2C-Bus + - microcrystal,rv3028 + # Real Time Clock Module with I2C-Bus + - microcrystal,rv3029 + # Real Time Clock + - microcrystal,rv8523 + # Real-time clock + - nxp,pcf2127 + # Real-time clock + - nxp,pcf2129 + # Real-time clock/calendar + - nxp,pcf8563 + # Real-time Clock Module + - pericom,pt7c4338 + # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC + - ricoh,r2025sd + # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC + - ricoh,r2221tl + # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC + - ricoh,rs5c372a + # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC + - ricoh,rs5c372b + # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC + - ricoh,rv5c386 + # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC + - ricoh,rv5c387a + # 2-wire CMOS real-time clock + - sii,s35390a + # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC + - whwave,sd3078 + # Xircom X1205 I2C RTC + - xircom,x1205 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + start-year: true + +required: + - compatible + - reg + +additionalProperties: false + +... diff --git a/Documentation/devicetree/bindings/serial/omap_serial.txt b/Documentation/devicetree/bindings/serial/omap_serial.txt index 0a9b5444f4e6..dcba86b0a0d0 100644 --- a/Documentation/devicetree/bindings/serial/omap_serial.txt +++ b/Documentation/devicetree/bindings/serial/omap_serial.txt @@ -1,6 +1,7 @@ OMAP UART controller Required properties: +- compatible : should be "ti,j721e-uart", "ti,am654-uart" for J721E controllers - compatible : should be "ti,am654-uart" for AM654 controllers - compatible : should be "ti,omap2-uart" for OMAP2 controllers - compatible : should be "ti,omap3-uart" for OMAP3 controllers diff --git a/Documentation/devicetree/bindings/soc/amlogic/amlogic,canvas.txt b/Documentation/devicetree/bindings/soc/amlogic/amlogic,canvas.txt index 436d2106e80d..e876f3ce54f6 100644 --- a/Documentation/devicetree/bindings/soc/amlogic/amlogic,canvas.txt +++ b/Documentation/devicetree/bindings/soc/amlogic/amlogic,canvas.txt @@ -2,8 +2,8 @@ Amlogic Canvas ================================ A canvas is a collection of metadata that describes a pixel buffer. -Those metadata include: width, height, phyaddr, wrapping, block mode -and endianness. +Those metadata include: width, height, phyaddr, wrapping and block mode. +Starting with GXBB the endianness can also be described. Many IPs within Amlogic SoCs rely on canvas indexes to read/write pixel data rather than use the phy addresses directly. For instance, this is the case for @@ -18,7 +18,11 @@ Video Lookup Table -------------------------- Required properties: -- compatible: "amlogic,canvas" +- compatible: has to be one of: + - "amlogic,meson8-canvas", "amlogic,canvas" on Meson8 + - "amlogic,meson8b-canvas", "amlogic,canvas" on Meson8b + - "amlogic,meson8m2-canvas", "amlogic,canvas" on Meson8m2 + - "amlogic,canvas" on GXBB and newer - reg: Base physical address and size of the canvas registers. Example: diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,aoss-qmp.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,aoss-qmp.txt new file mode 100644 index 000000000000..954ffee0a9c4 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,aoss-qmp.txt @@ -0,0 +1,81 @@ +Qualcomm Always-On Subsystem side channel binding + +This binding describes the hardware component responsible for side channel +requests to the always-on subsystem (AOSS), used for certain power management +requests that is not handled by the standard RPMh interface. Each client in the +SoC has it's own block of message RAM and IRQ for communication with the AOSS. +The protocol used to communicate in the message RAM is known as Qualcomm +Messaging Protocol (QMP) + +The AOSS side channel exposes control over a set of resources, used to control +a set of debug related clocks and to affect the low power state of resources +related to the secondary subsystems. These resources are exposed as a set of +power-domains. + +- compatible: + Usage: required + Value type: <string> + Definition: must be "qcom,sdm845-aoss-qmp" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the message RAM for this + client's communication with the AOSS + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the AOSS message IRQ for this client + +- mboxes: + Usage: required + Value type: <prop-encoded-array> + Definition: reference to the mailbox representing the outgoing doorbell + in APCS for this client, as described in mailbox/mailbox.txt + +- #clock-cells: + Usage: optional + Value type: <u32> + Definition: must be 0 + The single clock represents the QDSS clock. + +- #power-domain-cells: + Usage: optional + Value type: <u32> + Definition: must be 1 + The provided power-domains are: + CDSP state (0), LPASS state (1), modem state (2), SLPI + state (3), SPSS state (4) and Venus state (5). + += SUBNODES +The AOSS side channel also provides the controls for three cooling devices, +these are expressed as subnodes of the QMP node. The name of the node is used +to identify the resource and must therefor be "cx", "mx" or "ebi". + +- #cooling-cells: + Usage: optional + Value type: <u32> + Definition: must be 2 + += EXAMPLE + +The following example represents the AOSS side-channel message RAM and the +mechanism exposing the power-domains, as found in SDM845. + + aoss_qmp: qmp@c300000 { + compatible = "qcom,sdm845-aoss-qmp"; + reg = <0x0c300000 0x100000>; + interrupts = <GIC_SPI 389 IRQ_TYPE_EDGE_RISING>; + mboxes = <&apss_shared 0>; + + #power-domain-cells = <1>; + + cx_cdev: cx { + #cooling-cells = <2>; + }; + + mx_cdev: mx { + #cooling-cells = <2>; + }; + }; diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt index bcc612cc7423..db501269f47b 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt @@ -9,7 +9,7 @@ used for audio/voice services on the QDSP. Value type: <stringlist> Definition: must be "qcom,apr-v<VERSION-NUMBER>", example "qcom,apr-v2" -- reg +- qcom,apr-domain Usage: required Value type: <u32> Definition: Destination processor ID. @@ -49,9 +49,9 @@ by the individual bindings for the specific service The following example represents a QDSP based sound card on a MSM8996 device which uses apr as communication between Apps and QDSP. - apr@4 { + apr { compatible = "qcom,apr-v2"; - reg = <APR_DOMAIN_ADSP>; + qcom,apr-domain = <APR_DOMAIN_ADSP>; q6core@3 { compatible = "qcom,q6core"; diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt index cf759e5f9b10..1214192847ac 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt @@ -21,6 +21,11 @@ edge. Definition: should specify the IRQ used by the remote processor to signal this processor about communication related events +- qcom,remote-pid: + Usage: required for glink-smem + Value type: <u32> + Definition: specifies the identifier of the remote endpoint of this edge + - qcom,rpm-msg-ram: Usage: required for glink-rpm Value type: <prop-encoded-array> diff --git a/Documentation/devicetree/bindings/timer/renesas,cmt.txt b/Documentation/devicetree/bindings/timer/renesas,cmt.txt index c0594450e9ef..c5220bcd852b 100644 --- a/Documentation/devicetree/bindings/timer/renesas,cmt.txt +++ b/Documentation/devicetree/bindings/timer/renesas,cmt.txt @@ -42,12 +42,18 @@ Required Properties: - "renesas,r8a7793-cmt1" for the 48-bit CMT1 device included in r8a7793. - "renesas,r8a7794-cmt0" for the 32-bit CMT0 device included in r8a7794. - "renesas,r8a7794-cmt1" for the 48-bit CMT1 device included in r8a7794. + - "renesas,r8a7795-cmt0" for the 32-bit CMT0 device included in r8a7795. + - "renesas,r8a7795-cmt1" for the 48-bit CMT1 device included in r8a7795. - "renesas,r8a7796-cmt0" for the 32-bit CMT0 device included in r8a7796. - "renesas,r8a7796-cmt1" for the 48-bit CMT1 device included in r8a7796. + - "renesas,r8a77965-cmt0" for the 32-bit CMT0 device included in r8a77965. + - "renesas,r8a77965-cmt1" for the 48-bit CMT1 device included in r8a77965. - "renesas,r8a77970-cmt0" for the 32-bit CMT0 device included in r8a77970. - "renesas,r8a77970-cmt1" for the 48-bit CMT1 device included in r8a77970. - "renesas,r8a77980-cmt0" for the 32-bit CMT0 device included in r8a77980. - "renesas,r8a77980-cmt1" for the 48-bit CMT1 device included in r8a77980. + - "renesas,r8a77990-cmt0" for the 32-bit CMT0 device included in r8a77990. + - "renesas,r8a77990-cmt1" for the 48-bit CMT1 device included in r8a77990. - "renesas,rcar-gen2-cmt0" for 32-bit CMT0 devices included in R-Car Gen2 and RZ/G1. diff --git a/Documentation/devicetree/bindings/usb/s3c2410-usb.txt b/Documentation/devicetree/bindings/usb/s3c2410-usb.txt index e45b38ce2986..26c85afd0b53 100644 --- a/Documentation/devicetree/bindings/usb/s3c2410-usb.txt +++ b/Documentation/devicetree/bindings/usb/s3c2410-usb.txt @@ -4,7 +4,7 @@ OHCI Required properties: - compatible: should be "samsung,s3c2410-ohci" for USB host controller - - reg: address and lenght of the controller memory mapped region + - reg: address and length of the controller memory mapped region - interrupts: interrupt number for the USB OHCI controller - clocks: Should reference the bus and host clocks - clock-names: Should contain two strings diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index eade302345a3..6992bbbbffab 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -395,12 +395,16 @@ patternProperties: description: Holt Integrated Circuits, Inc. "^honeywell,.*": description: Honeywell + "^hoperun,.*": + description: Jiangsu HopeRun Software Co., Ltd. "^hp,.*": description: Hewlett Packard "^hsg,.*": description: HannStar Display Co. "^holtek,.*": description: Holtek Semiconductor, Inc. + "^hugsun,.*": + description: Shenzhen Hugsun Technology Co. Ltd. "^hwacom,.*": description: HwaCom Systems Inc. "^hyundai,.*": @@ -735,6 +739,8 @@ patternProperties: description: PROBOX2 (by W2COMP Co., Ltd.) "^pulsedlight,.*": description: PulsedLight, Inc + "^purism,.*": + description: Purism, SPC "^qca,.*": description: Qualcomm Atheros, Inc. "^qcom,.*": diff --git a/Documentation/devicetree/bindings/virtio/iommu.txt b/Documentation/devicetree/bindings/virtio/iommu.txt new file mode 100644 index 000000000000..2407fea0651c --- /dev/null +++ b/Documentation/devicetree/bindings/virtio/iommu.txt @@ -0,0 +1,66 @@ +* virtio IOMMU PCI device + +When virtio-iommu uses the PCI transport, its programming interface is +discovered dynamically by the PCI probing infrastructure. However the +device tree statically describes the relation between IOMMU and DMA +masters. Therefore, the PCI root complex that hosts the virtio-iommu +contains a child node representing the IOMMU device explicitly. + +Required properties: + +- compatible: Should be "virtio,pci-iommu" +- reg: PCI address of the IOMMU. As defined in the PCI Bus + Binding reference [1], the reg property is a five-cell + address encoded as (phys.hi phys.mid phys.lo size.hi + size.lo). phys.hi should contain the device's BDF as + 0b00000000 bbbbbbbb dddddfff 00000000. The other cells + should be zero. +- #iommu-cells: Each platform DMA master managed by the IOMMU is assigned + an endpoint ID, described by the "iommus" property [2]. + For virtio-iommu, #iommu-cells must be 1. + +Notes: + +- DMA from the IOMMU device isn't managed by another IOMMU. Therefore the + virtio-iommu node doesn't have an "iommus" property, and is omitted from + the iommu-map property of the root complex. + +Example: + +pcie@10000000 { + compatible = "pci-host-ecam-generic"; + ... + + /* The IOMMU programming interface uses slot 00:01.0 */ + iommu0: iommu@0008 { + compatible = "virtio,pci-iommu"; + reg = <0x00000800 0 0 0 0>; + #iommu-cells = <1>; + }; + + /* + * The IOMMU manages all functions in this PCI domain except + * itself. Omit BDF 00:01.0. + */ + iommu-map = <0x0 &iommu0 0x0 0x8> + <0x9 &iommu0 0x9 0xfff7>; +}; + +pcie@20000000 { + compatible = "pci-host-ecam-generic"; + ... + /* + * The IOMMU also manages all functions from this domain, + * with endpoint IDs 0x10000 - 0x1ffff + */ + iommu-map = <0x0 &iommu0 0x10000 0x10000>; +}; + +ethernet@fe001000 { + ... + /* The IOMMU manages this platform device with endpoint ID 0x20000 */ + iommus = <&iommu0 0x20000>; +}; + +[1] Documentation/devicetree/bindings/pci/pci.txt +[2] Documentation/devicetree/bindings/iommu/iommu.txt diff --git a/Documentation/devicetree/bindings/virtio/mmio.txt b/Documentation/devicetree/bindings/virtio/mmio.txt index 5069c1b8e193..21af30fbb81f 100644 --- a/Documentation/devicetree/bindings/virtio/mmio.txt +++ b/Documentation/devicetree/bindings/virtio/mmio.txt @@ -8,10 +8,40 @@ Required properties: - reg: control registers base address and size including configuration space - interrupts: interrupt generated by the device +Required properties for virtio-iommu: + +- #iommu-cells: When the node corresponds to a virtio-iommu device, it is + linked to DMA masters using the "iommus" or "iommu-map" + properties [1][2]. #iommu-cells specifies the size of the + "iommus" property. For virtio-iommu #iommu-cells must be + 1, each cell describing a single endpoint ID. + +Optional properties: + +- iommus: If the device accesses memory through an IOMMU, it should + have an "iommus" property [1]. Since virtio-iommu itself + does not access memory through an IOMMU, the "virtio,mmio" + node cannot have both an "#iommu-cells" and an "iommus" + property. + Example: virtio_block@3000 { compatible = "virtio,mmio"; reg = <0x3000 0x100>; interrupts = <41>; + + /* Device has endpoint ID 23 */ + iommus = <&viommu 23> } + + viommu: iommu@3100 { + compatible = "virtio,mmio"; + reg = <0x3100 0x100>; + interrupts = <42>; + + #iommu-cells = <1> + } + +[1] Documentation/devicetree/bindings/iommu/iommu.txt +[2] Documentation/devicetree/bindings/pci/pci-iommu.txt diff --git a/Documentation/devicetree/bindings/watchdog/fsl-imx-sc-wdt.txt b/Documentation/devicetree/bindings/watchdog/fsl-imx-sc-wdt.txt deleted file mode 100644 index 02b87e92ae68..000000000000 --- a/Documentation/devicetree/bindings/watchdog/fsl-imx-sc-wdt.txt +++ /dev/null @@ -1,24 +0,0 @@ -* Freescale i.MX System Controller Watchdog - -i.MX system controller watchdog is for i.MX SoCs with system controller inside, -the watchdog is managed by system controller, users can ONLY communicate with -system controller from secure mode for watchdog operations, so Linux i.MX system -controller watchdog driver will call ARM SMC API and trap into ARM-Trusted-Firmware -for watchdog operations, ARM-Trusted-Firmware is running at secure EL3 mode and -it will request system controller to execute the watchdog operation passed from -Linux kernel. - -Required properties: -- compatible: Should be : - "fsl,imx8qxp-sc-wdt" - followed by "fsl,imx-sc-wdt"; - -Optional properties: -- timeout-sec : Contains the watchdog timeout in seconds. - -Examples: - -watchdog { - compatible = "fsl,imx8qxp-sc-wdt", "fsl,imx-sc-wdt"; - timeout-sec = <60>; -}; diff --git a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt b/Documentation/devicetree/bindings/watchdog/renesas,wdt.txt index 9f365c1a3399..9f365c1a3399 100644 --- a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/renesas,wdt.txt diff --git a/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt b/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt index 46055254e8dd..e65198d82a2b 100644 --- a/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt @@ -6,6 +6,7 @@ Required properties: "allwinner,sun4i-a10-wdt" "allwinner,sun6i-a31-wdt" "allwinner,sun50i-a64-wdt","allwinner,sun6i-a31-wdt" + "allwinner,sun50i-h6-wdt","allwinner,sun6i-a31-wdt" "allwinner,suniv-f1c100s-wdt", "allwinner,sun4i-a10-wdt" - reg : Specifies base physical address and size of the registers. diff --git a/Documentation/devicetree/booting-without-of.txt b/Documentation/devicetree/booting-without-of.txt index 60f8640f2b2f..4660ccee35a3 100644 --- a/Documentation/devicetree/booting-without-of.txt +++ b/Documentation/devicetree/booting-without-of.txt @@ -160,7 +160,7 @@ it with special cases. of the kernel image. That entry point supports two calling conventions. A summary of the interface is described here. A full description of the boot requirements is documented in - Documentation/arm/Booting + Documentation/arm/booting.rst a) ATAGS interface. Minimal information is passed from firmware to the kernel with a tagged list of predefined parameters. @@ -174,7 +174,7 @@ it with special cases. b) Entry with a flattened device-tree block. Firmware loads the physical address of the flattened device tree block (dtb) into r2, r1 is not used, but it is considered good practice to use a valid - machine number as described in Documentation/arm/Booting. + machine number as described in Documentation/arm/booting.rst. r0 : 0 |