diff options
Diffstat (limited to 'Documentation/devicetree')
197 files changed, 4099 insertions, 244 deletions
diff --git a/Documentation/devicetree/bindings/arm/arm,scmi.txt b/Documentation/devicetree/bindings/arm/arm,scmi.txt new file mode 100644 index 000000000000..5f3719ab7075 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/arm,scmi.txt @@ -0,0 +1,179 @@ +System Control and Management Interface (SCMI) Message Protocol +---------------------------------------------------------- + +The SCMI is intended to allow agents such as OSPM to manage various functions +that are provided by the hardware platform it is running on, including power +and performance functions. + +This binding is intended to define the interface the firmware implementing +the SCMI as described in ARM document number ARM DUI 0922B ("ARM System Control +and Management Interface Platform Design Document")[0] provide for OSPM in +the device tree. + +Required properties: + +The scmi node with the following properties shall be under the /firmware/ node. + +- compatible : shall be "arm,scmi" +- mboxes: List of phandle and mailbox channel specifiers. It should contain + exactly one or two mailboxes, one for transmitting messages("tx") + and another optional for receiving the notifications("rx") if + supported. +- shmem : List of phandle pointing to the shared memory(SHM) area as per + generic mailbox client binding. +- #address-cells : should be '1' if the device has sub-nodes, maps to + protocol identifier for a given sub-node. +- #size-cells : should be '0' as 'reg' property doesn't have any size + associated with it. + +Optional properties: + +- mbox-names: shall be "tx" or "rx" depending on mboxes entries. + +See Documentation/devicetree/bindings/mailbox/mailbox.txt for more details +about the generic mailbox controller and client driver bindings. + +The mailbox is the only permitted method of calling the SCMI firmware. +Mailbox doorbell is used as a mechanism to alert the presence of a +messages and/or notification. + +Each protocol supported shall have a sub-node with corresponding compatible +as described in the following sections. If the platform supports dedicated +communication channel for a particular protocol, the 3 properties namely: +mboxes, mbox-names and shmem shall be present in the sub-node corresponding +to that protocol. + +Clock/Performance bindings for the clocks/OPPs based on SCMI Message Protocol +------------------------------------------------------------ + +This binding uses the common clock binding[1]. + +Required properties: +- #clock-cells : Should be 1. Contains the Clock ID value used by SCMI commands. + +Power domain bindings for the power domains based on SCMI Message Protocol +------------------------------------------------------------ + +This binding for the SCMI power domain providers uses the generic power +domain binding[2]. + +Required properties: + - #power-domain-cells : Should be 1. Contains the device or the power + domain ID value used by SCMI commands. + +Sensor bindings for the sensors based on SCMI Message Protocol +-------------------------------------------------------------- +SCMI provides an API to access the various sensors on the SoC. + +Required properties: +- #thermal-sensor-cells: should be set to 1. This property follows the + thermal device tree bindings[3]. + + Valid cell values are raw identifiers (Sensor ID) + as used by the firmware. Refer to platform details + for your implementation for the IDs to use. + +SRAM and Shared Memory for SCMI +------------------------------- + +A small area of SRAM is reserved for SCMI communication between application +processors and SCP. + +The properties should follow the generic mmio-sram description found in [4] + +Each sub-node represents the reserved area for SCMI. + +Required sub-node properties: +- reg : The base offset and size of the reserved area with the SRAM +- compatible : should be "arm,scmi-shmem" for Non-secure SRAM based + shared memory + +[0] http://infocenter.arm.com/help/topic/com.arm.doc.den0056a/index.html +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/power/power_domain.txt +[3] Documentation/devicetree/bindings/thermal/thermal.txt +[4] Documentation/devicetree/bindings/sram/sram.txt + +Example: + +sram@50000000 { + compatible = "mmio-sram"; + reg = <0x0 0x50000000 0x0 0x10000>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x0 0x50000000 0x10000>; + + cpu_scp_lpri: scp-shmem@0 { + compatible = "arm,scmi-shmem"; + reg = <0x0 0x200>; + }; + + cpu_scp_hpri: scp-shmem@200 { + compatible = "arm,scmi-shmem"; + reg = <0x200 0x200>; + }; +}; + +mailbox@40000000 { + .... + #mbox-cells = <1>; + reg = <0x0 0x40000000 0x0 0x10000>; +}; + +firmware { + + ... + + scmi { + compatible = "arm,scmi"; + mboxes = <&mailbox 0 &mailbox 1>; + mbox-names = "tx", "rx"; + shmem = <&cpu_scp_lpri &cpu_scp_hpri>; + #address-cells = <1>; + #size-cells = <0>; + + scmi_devpd: protocol@11 { + reg = <0x11>; + #power-domain-cells = <1>; + }; + + scmi_dvfs: protocol@13 { + reg = <0x13>; + #clock-cells = <1>; + }; + + scmi_clk: protocol@14 { + reg = <0x14>; + #clock-cells = <1>; + }; + + scmi_sensors0: protocol@15 { + reg = <0x15>; + #thermal-sensor-cells = <1>; + }; + }; +}; + +cpu@0 { + ... + reg = <0 0>; + clocks = <&scmi_dvfs 0>; +}; + +hdlcd@7ff60000 { + ... + reg = <0 0x7ff60000 0 0x1000>; + clocks = <&scmi_clk 4>; + power-domains = <&scmi_devpd 1>; +}; + +thermal-zones { + soc_thermal { + polling-delay-passive = <100>; + polling-delay = <1000>; + /* sensor ID */ + thermal-sensors = <&scmi_sensors0 3>; + ... + }; +}; diff --git a/Documentation/devicetree/bindings/arm/cpu-enable-method/nuvoton,npcm750-smp b/Documentation/devicetree/bindings/arm/cpu-enable-method/nuvoton,npcm750-smp new file mode 100644 index 000000000000..8e043301e28e --- /dev/null +++ b/Documentation/devicetree/bindings/arm/cpu-enable-method/nuvoton,npcm750-smp @@ -0,0 +1,42 @@ +========================================================= +Secondary CPU enable-method "nuvoton,npcm750-smp" binding +========================================================= + +To apply to all CPUs, a single "nuvoton,npcm750-smp" enable method should be +defined in the "cpus" node. + +Enable method name: "nuvoton,npcm750-smp" +Compatible machines: "nuvoton,npcm750" +Compatible CPUs: "arm,cortex-a9" +Related properties: (none) + +Note: +This enable method needs valid nodes compatible with "arm,cortex-a9-scu" and +"nuvoton,npcm750-gcr". + +Example: + + cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "nuvoton,npcm750-smp"; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + clocks = <&clk NPCM7XX_CLK_CPU>; + clock-names = "clk_cpu"; + reg = <0>; + next-level-cache = <&L2>; + }; + + cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + clocks = <&clk NPCM7XX_CLK_CPU>; + clock-names = "clk_cpu"; + reg = <1>; + next-level-cache = <&L2>; + }; + }; + diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index f4a777039f03..29e1dc5d506d 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -185,6 +185,7 @@ described below. "nvidia,tegra186-denver" "qcom,krait" "qcom,kryo" + "qcom,kryo385" "qcom,scorpion" - enable-method Value type: <stringlist> @@ -198,6 +199,7 @@ described below. "actions,s500-smp" "allwinner,sun6i-a31" "allwinner,sun8i-a23" + "allwinner,sun9i-a80-smp" "amlogic,meson8-smp" "amlogic,meson8b-smp" "arm,realview-smp" diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon-low-pin-count.txt b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon-low-pin-count.txt new file mode 100644 index 000000000000..10bd35f9207f --- /dev/null +++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon-low-pin-count.txt @@ -0,0 +1,33 @@ +Hisilicon Hip06 Low Pin Count device + Hisilicon Hip06 SoCs implement a Low Pin Count (LPC) controller, which + provides I/O access to some legacy ISA devices. + Hip06 is based on arm64 architecture where there is no I/O space. So, the + I/O ports here are not CPU addresses, and there is no 'ranges' property in + LPC device node. + +Required properties: +- compatible: value should be as follows: + (a) "hisilicon,hip06-lpc" + (b) "hisilicon,hip07-lpc" +- #address-cells: must be 2 which stick to the ISA/EISA binding doc. +- #size-cells: must be 1 which stick to the ISA/EISA binding doc. +- reg: base memory range where the LPC register set is mapped. + +Note: + The node name before '@' must be "isa" to represent the binding stick to the + ISA/EISA binding specification. + +Example: + +isa@a01b0000 { + compatible = "hisilicon,hip06-lpc"; + #address-cells = <2>; + #size-cells = <1>; + reg = <0x0 0xa01b0000 0x0 0x1000>; + + ipmi0: bt@e4 { + compatible = "ipmi-bt"; + device_type = "ipmi"; + reg = <0x01 0xe4 0x04>; + }; +}; diff --git a/Documentation/devicetree/bindings/arm/mediatek.txt b/Documentation/devicetree/bindings/arm/mediatek.txt index 91d517849483..7d21ab37c19c 100644 --- a/Documentation/devicetree/bindings/arm/mediatek.txt +++ b/Documentation/devicetree/bindings/arm/mediatek.txt @@ -50,6 +50,15 @@ Supported boards: - Reference board variant 1 for MT7622: Required root node properties: - compatible = "mediatek,mt7622-rfb1", "mediatek,mt7622"; +- Reference board for MT7623a with eMMC: + Required root node properties: + - compatible = "mediatek,mt7623a-rfb-emmc", "mediatek,mt7623"; +- Reference board for MT7623a with NAND: + Required root node properties: + - compatible = "mediatek,mt7623a-rfb-nand", "mediatek,mt7623"; +- Reference board for MT7623n with eMMC: + Required root node properties: + - compatible = "mediatek,mt7623n-rfb-emmc", "mediatek,mt7623"; - Reference board for MT7623n with NAND: Required root node properties: - compatible = "mediatek,mt7623n-rfb-nand", "mediatek,mt7623"; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt index 9b8f578d5e19..34a69ba67f13 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt @@ -6,6 +6,7 @@ The MediaTek AUDSYS controller provides various clocks to the system. Required Properties: - compatible: Should be one of: + - "mediatek,mt2701-audsys", "syscon" - "mediatek,mt7622-audsys", "syscon" - #clock-cells: Must be 1 @@ -13,10 +14,19 @@ The AUDSYS controller uses the common clk binding from Documentation/devicetree/bindings/clock/clock-bindings.txt The available clocks are defined in dt-bindings/clock/mt*-clk.h. +Required sub-nodes: +------- +For common binding part and usage, refer to +../sonud/mt2701-afe-pcm.txt. + Example: -audsys: audsys@11220000 { - compatible = "mediatek,mt7622-audsys", "syscon"; - reg = <0 0x11220000 0 0x1000>; - #clock-cells = <1>; -}; + audsys: clock-controller@11220000 { + compatible = "mediatek,mt7622-audsys", "syscon"; + reg = <0 0x11220000 0 0x2000>; + #clock-cells = <1>; + + afe: audio-controller { + ... + }; + }; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt index 6cc7840ff37a..8f5335b480ac 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt @@ -9,6 +9,7 @@ Required Properties: - "mediatek,mt2701-ethsys", "syscon" - "mediatek,mt7622-ethsys", "syscon" - #clock-cells: Must be 1 +- #reset-cells: Must be 1 The ethsys controller uses the common clk binding from Documentation/devicetree/bindings/clock/clock-bindings.txt diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,pciesys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,pciesys.txt index d5d5f1227665..7fe5dc6097a6 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,pciesys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,pciesys.txt @@ -8,6 +8,7 @@ Required Properties: - compatible: Should be: - "mediatek,mt7622-pciesys", "syscon" - #clock-cells: Must be 1 +- #reset-cells: Must be 1 The PCIESYS controller uses the common clk binding from Documentation/devicetree/bindings/clock/clock-bindings.txt @@ -19,4 +20,5 @@ pciesys: pciesys@1a100800 { compatible = "mediatek,mt7622-pciesys", "syscon"; reg = <0 0x1a100800 0 0x1000>; #clock-cells = <1>; + #reset-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,ssusbsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ssusbsys.txt index 00760019da00..b8184da2508c 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,ssusbsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ssusbsys.txt @@ -8,6 +8,7 @@ Required Properties: - compatible: Should be: - "mediatek,mt7622-ssusbsys", "syscon" - #clock-cells: Must be 1 +- #reset-cells: Must be 1 The SSUSBSYS controller uses the common clk binding from Documentation/devicetree/bindings/clock/clock-bindings.txt @@ -19,4 +20,5 @@ ssusbsys: ssusbsys@1a000000 { compatible = "mediatek,mt7622-ssusbsys", "syscon"; reg = <0 0x1a000000 0 0x1000>; #clock-cells = <1>; + #reset-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/arm/npcm/npcm.txt b/Documentation/devicetree/bindings/arm/npcm/npcm.txt new file mode 100644 index 000000000000..2d87d9ecea85 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/npcm/npcm.txt @@ -0,0 +1,6 @@ +NPCM Platforms Device Tree Bindings +----------------------------------- +NPCM750 SoC +Required root node properties: + - compatible = "nuvoton,npcm750"; + diff --git a/Documentation/devicetree/bindings/arm/omap/ctrl.txt b/Documentation/devicetree/bindings/arm/omap/ctrl.txt index ce8dabf8c0f9..f35b77920786 100644 --- a/Documentation/devicetree/bindings/arm/omap/ctrl.txt +++ b/Documentation/devicetree/bindings/arm/omap/ctrl.txt @@ -25,6 +25,7 @@ Required properties: "ti,omap4-scm-padconf-wkup" "ti,omap5-scm-core" "ti,omap5-scm-padconf-core" + "ti,omap5-scm-wkup-pad-conf" "ti,dra7-scm-core" - reg: Contains Control Module register address range (base address and length) diff --git a/Documentation/devicetree/bindings/arm/omap/mpu.txt b/Documentation/devicetree/bindings/arm/omap/mpu.txt index 763695db2bd9..f301e636fd52 100644 --- a/Documentation/devicetree/bindings/arm/omap/mpu.txt +++ b/Documentation/devicetree/bindings/arm/omap/mpu.txt @@ -13,6 +13,13 @@ Required properties: Optional properties: - sram: Phandle to the ocmcram node +am335x and am437x only: +- pm-sram: Phandles to ocmcram nodes to be used for power management. + First should be type 'protect-exec' for the driver to use to copy + and run PM functions, second should be regular pool to be used for + data region for code. See Documentation/devicetree/bindings/sram/sram.txt + for more details. + Examples: - For an OMAP5 SMP system: @@ -36,3 +43,12 @@ mpu { compatible = "ti,omap3-mpu"; ti,hwmods = "mpu"; }; + +- For an AM335x system: + +mpu { + compatible = "ti,omap3-mpu"; + ti,hwmods = "mpu"; + pm-sram = <&pm_sram_code + &pm_sram_data>; +}; diff --git a/Documentation/devicetree/bindings/arm/qcom.txt b/Documentation/devicetree/bindings/arm/qcom.txt index 0ed4d39d7fe1..ee532e705d6c 100644 --- a/Documentation/devicetree/bindings/arm/qcom.txt +++ b/Documentation/devicetree/bindings/arm/qcom.txt @@ -26,6 +26,7 @@ The 'SoC' element must be one of the following strings: msm8996 mdm9615 ipq8074 + sdm845 The 'board' element must be one of the following strings: diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index 326d24bca1a9..1c1d62d03c4f 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -50,6 +50,10 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "firefly,firefly-rk3399", "rockchip,rk3399"; +- Firefly roc-rk3328-cc board: + Required root node properties: + - compatible = "firefly,roc-rk3328-cc", "rockchip,rk3328"; + - ChipSPARK PopMetal-RK3288 board: Required root node properties: - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288"; @@ -181,10 +185,18 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "rockchip,rk3399-evb", "rockchip,rk3399"; +- Rockchip RK3399 Sapphire board standalone: + Required root node properties: + - compatible = "rockchip,rk3399-sapphire", "rockchip,rk3399"; + - Rockchip RK3399 Sapphire Excavator board: Required root node properties: - compatible = "rockchip,rk3399-sapphire-excavator", "rockchip,rk3399"; +- Theobroma Systems RK3368-uQ7 Haikou Baseboard: + Required root node properties: + - compatible = "tsd,rk3368-uq7-haikou", "rockchip,rk3368"; + - Theobroma Systems RK3399-Q7 Haikou Baseboard: Required root node properties: - compatible = "tsd,rk3399-q7-haikou", "rockchip,rk3399"; diff --git a/Documentation/devicetree/bindings/arm/samsung/pmu.txt b/Documentation/devicetree/bindings/arm/samsung/pmu.txt index 779f5614bcee..16685787d2bd 100644 --- a/Documentation/devicetree/bindings/arm/samsung/pmu.txt +++ b/Documentation/devicetree/bindings/arm/samsung/pmu.txt @@ -43,6 +43,12 @@ following properties: - interrupt-parent: a phandle indicating which interrupt controller this PMU signals interrupts to. + +Optional nodes: + +- nodes defining the restart and poweroff syscon children + + Example : pmu_system_controller: system-controller@10040000 { compatible = "samsung,exynos5250-pmu", "syscon"; diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt index 469ac98ecf8f..14510b215480 100644 --- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt @@ -9,7 +9,11 @@ Required root node properties: - "samsung,smdkv310" - for Exynos4210-based Samsung SMDKV310 eval board. - "samsung,trats" - for Exynos4210-based Tizen Reference board. - "samsung,universal_c210" - for Exynos4210-based Samsung board. + - "samsung,i9300" - for Exynos4412-based Samsung GT-I9300 board. + - "samsung,i9305" - for Exynos4412-based Samsung GT-I9305 board. + - "samsung,midas" - for Exynos4412-based Samsung Midas board. - "samsung,smdk4412", - for Exynos4412-based Samsung SMDK4412 eval board. + - "samsung,n710x" - for Exynos4412-based Samsung GT-N7100/GT-N7105 board. - "samsung,trats2" - for Exynos4412-based Tizen Reference board. - "samsung,smdk5250" - for Exynos5250-based Samsung SMDK5250 eval board. - "samsung,xyref5260" - for Exynos5260-based Samsung board. diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt index 5c3af7ef0761..d3d1df97834f 100644 --- a/Documentation/devicetree/bindings/arm/shmobile.txt +++ b/Documentation/devicetree/bindings/arm/shmobile.txt @@ -39,8 +39,12 @@ SoCs: compatible = "renesas,r8a7795" - R-Car M3-W (R8A77960) compatible = "renesas,r8a7796" + - R-Car M3-N (R8A77965) + compatible = "renesas,r8a77965" - R-Car V3M (R8A77970) compatible = "renesas,r8a77970" + - R-Car V3H (R8A77980) + compatible = "renesas,r8a77980" - R-Car D3 (R8A77995) compatible = "renesas,r8a77995" @@ -52,11 +56,13 @@ Boards: - APE6-EVM compatible = "renesas,ape6evm", "renesas,r8a73a4" - Atmark Techno Armadillo-800 EVA - compatible = "renesas,armadillo800eva" + compatible = "renesas,armadillo800eva", "renesas,r8a7740" - Blanche (RTP0RC7792SEB00010S) compatible = "renesas,blanche", "renesas,r8a7792" - BOCK-W compatible = "renesas,bockw", "renesas,r8a7778" + - Condor (RTP0RC77980SEB0010SS/RTP0RC77980SEB0010SA01) + compatible = "renesas,condor", "renesas,r8a77980" - Draak (RTP0RC77995SEB0010S) compatible = "renesas,draak", "renesas,r8a77995" - Eagle (RTP0RC77970SEB0010S) @@ -102,19 +108,25 @@ Boards: compatible = "renesas,salvator-x", "renesas,r8a7795" - Salvator-X (RTP0RC7796SIPB0011S) compatible = "renesas,salvator-x", "renesas,r8a7796" + - Salvator-X (RTP0RC7796SIPB0011S (M3N)) + compatible = "renesas,salvator-x", "renesas,r8a77965" - Salvator-XS (Salvator-X 2nd version, RTP0RC7795SIPB0012S) compatible = "renesas,salvator-xs", "renesas,r8a7795" - Salvator-XS (Salvator-X 2nd version, RTP0RC7796SIPB0012S) compatible = "renesas,salvator-xs", "renesas,r8a7796" + - Salvator-XS (Salvator-X 2nd version, RTP0RC77965SIPB012S) + compatible = "renesas,salvator-xs", "renesas,r8a77965" - SILK (RTP0RC7794LCB00011S) compatible = "renesas,silk", "renesas,r8a7794" - SK-RZG1E (YR8A77450S000BE) compatible = "renesas,sk-rzg1e", "renesas,r8a7745" - SK-RZG1M (YR8A77430S000BE) compatible = "renesas,sk-rzg1m", "renesas,r8a7743" - - V3MSK + - Stout (ADAS Starterkit, Y-R-CAR-ADAS-SKH2-BOARD) + compatible = "renesas,stout", "renesas,r8a7790" + - V3MSK (Y-ASK-RCAR-V3M-WS10) compatible = "renesas,v3msk", "renesas,r8a77970" - - Wheat + - Wheat (RTP0RC7792ASKB0000JE) compatible = "renesas,wheat", "renesas,r8a7792" diff --git a/Documentation/devicetree/bindings/arm/stm32.txt b/Documentation/devicetree/bindings/arm/stm32.txt index 05762b08a7bb..6808ed9ddfd5 100644 --- a/Documentation/devicetree/bindings/arm/stm32.txt +++ b/Documentation/devicetree/bindings/arm/stm32.txt @@ -7,3 +7,4 @@ using one of the following compatible strings: st,stm32f469 st,stm32f746 st,stm32h743 + st,stm32mp157 diff --git a/Documentation/devicetree/bindings/arm/sunxi/smp-sram.txt b/Documentation/devicetree/bindings/arm/sunxi/smp-sram.txt new file mode 100644 index 000000000000..082e6a9382d3 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/sunxi/smp-sram.txt @@ -0,0 +1,44 @@ +Allwinner SRAM for smp bringup: +------------------------------------------------ + +Allwinner's A80 SoC uses part of the secure sram for hotplugging of the +primary core (cpu0). Once the core gets powered up it checks if a magic +value is set at a specific location. If it is then the BROM will jump +to the software entry address, instead of executing a standard boot. + +Therefore a reserved section sub-node has to be added to the mmio-sram +declaration. + +Note that this is separate from the Allwinner SRAM controller found in +../../sram/sunxi-sram.txt. This SRAM is secure only and not mappable to +any device. + +Also there are no "secure-only" properties. The implementation should +check if this SRAM is usable first. + +Required sub-node properties: +- compatible : depending on the SoC this should be one of: + "allwinner,sun9i-a80-smp-sram" + +The rest of the properties should follow the generic mmio-sram discription +found in ../../misc/sram.txt + +Example: + + sram_b: sram@20000 { + /* 256 KiB secure SRAM at 0x20000 */ + compatible = "mmio-sram"; + reg = <0x00020000 0x40000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x00020000 0x40000>; + + smp-sram@1000 { + /* + * This is checked by BROM to determine if + * cpu0 should jump to SMP entry vector + */ + compatible = "allwinner,sun9i-a80-smp-sram"; + reg = <0x1000 0x8>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/tegra.txt b/Documentation/devicetree/bindings/arm/tegra.txt index 7f1411bbabf7..32f62bb7006d 100644 --- a/Documentation/devicetree/bindings/arm/tegra.txt +++ b/Documentation/devicetree/bindings/arm/tegra.txt @@ -9,6 +9,12 @@ following compatible values: nvidia,tegra20 nvidia,tegra30 + nvidia,tegra114 + nvidia,tegra124 + nvidia,tegra132 + nvidia,tegra210 + nvidia,tegra186 + nvidia,tegra194 Boards ------------------------------------------- @@ -26,8 +32,18 @@ board-specific compatible values: nvidia,cardhu nvidia,cardhu-a02 nvidia,cardhu-a04 + nvidia,dalmore nvidia,harmony + nvidia,jetson-tk1 + nvidia,norrin + nvidia,p2371-0000 + nvidia,p2371-2180 + nvidia,p2571 + nvidia,p2771-0000 + nvidia,p2972-0000 + nvidia,roth nvidia,seaboard + nvidia,tn7 nvidia,ventana toradex,apalis_t30 toradex,apalis_t30-eval diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt index 078a58b0302f..5a3bf7c5a7a0 100644 --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt @@ -3,6 +3,7 @@ NVIDIA Tegra Power Management Controller (PMC) Required properties: - compatible: Should contain one of the following: - "nvidia,tegra186-pmc": for Tegra186 + - "nvidia,tegra194-pmc": for Tegra194 - reg: Must contain an (offset, length) pair of the register set for each entry in reg-names. - reg-names: Must include the following entries: @@ -10,6 +11,7 @@ Required properties: - "wake" - "aotag" - "scratch" + - "misc" (Only for Tegra194) Optional properties: - nvidia,invert-interrupt: If present, inverts the PMU interrupt signal. diff --git a/Documentation/devicetree/bindings/arm/xilinx.txt b/Documentation/devicetree/bindings/arm/xilinx.txt index 1f7995357888..b9043bc35c14 100644 --- a/Documentation/devicetree/bindings/arm/xilinx.txt +++ b/Documentation/devicetree/bindings/arm/xilinx.txt @@ -5,3 +5,59 @@ shall have the following properties. Required root node properties: - compatible = "xlnx,zynq-7000"; + +Additional compatible strings: + +- Xilinx internal board cc108 + "xlnx,zynq-cc108" + +- Xilinx internal board zc770 with different FMC cards + "xlnx,zynq-zc770-xm010" + "xlnx,zynq-zc770-xm011" + "xlnx,zynq-zc770-xm012" + "xlnx,zynq-zc770-xm013" + +- Digilent Zybo Z7 board + "digilent,zynq-zybo-z7" + +--------------------------------------------------------------- + +Xilinx Zynq UltraScale+ MPSoC Platforms Device Tree Bindings + +Boards with ZynqMP SOC based on an ARM Cortex A53 processor +shall have the following properties. + +Required root node properties: + - compatible = "xlnx,zynqmp"; + + +Additional compatible strings: + +- Xilinx internal board zc1232 + "xlnx,zynqmp-zc1232-revA", "xlnx,zynqmp-zc1232" + +- Xilinx internal board zc1254 + "xlnx,zynqmp-zc1254-revA", "xlnx,zynqmp-zc1254" + +- Xilinx internal board zc1275 + "xlnx,zynqmp-zc1275-revA", "xlnx,zynqmp-zc1275" + +- Xilinx internal board zc1751 + "xlnx,zynqmp-zc1751" + +- Xilinx 96boards compatible board zcu100 + "xlnx,zynqmp-zcu100-revC", "xlnx,zynqmp-zcu100" + +- Xilinx evaluation board zcu102 + "xlnx,zynqmp-zcu102-revA", "xlnx,zynqmp-zcu102" + "xlnx,zynqmp-zcu102-revB", "xlnx,zynqmp-zcu102" + "xlnx,zynqmp-zcu102-rev1.0", "xlnx,zynqmp-zcu102" + +- Xilinx evaluation board zcu104 + "xlnx,zynqmp-zcu104-revA", "xlnx,zynqmp-zcu104" + +- Xilinx evaluation board zcu106 + "xlnx,zynqmp-zcu106-revA", "xlnx,zynqmp-zcu106" + +- Xilinx evaluation board zcu111 + "xlnx,zynqmp-zcu111-revA", "xlnx,zynqmp-zcu111" diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt index f4006d3c9fdf..c760ecb81381 100644 --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -30,7 +30,6 @@ compatible: Optional properties: - dma-coherent : Present if dma operations are coherent - clocks : a list of phandle + clock specifier pairs -- resets : a list of phandle + reset specifier pairs - target-supply : regulator for SATA target power - phys : reference to the SATA PHY node - phy-names : must be "sata-phy" diff --git a/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt b/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt index 3e21eb822811..c1e70621799b 100644 --- a/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt +++ b/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt @@ -73,7 +73,7 @@ Example with two SJA1000 CAN controllers connected to the GMI bus. We wrap the controllers with a simple-bus node since they are all connected to the same chip-select (CS4), in this example external address decoding is provided: -gmi@70090000 { +gmi@70009000 { compatible = "nvidia,tegra20-gmi"; reg = <0x70009000 0x1000>; #address-cells = <2>; @@ -84,7 +84,6 @@ gmi@70090000 { reset-names = "gmi"; ranges = <4 0 0xd0000000 0xfffffff>; - bus@4,0 { compatible = "simple-bus"; #address-cells = <1>; @@ -109,7 +108,7 @@ gmi@70090000 { Example with one SJA1000 CAN controller connected to the GMI bus on CS4: -gmi@70090000 { +gmi@70009000 { compatible = "nvidia,tegra20-gmi"; reg = <0x70009000 0x1000>; #address-cells = <2>; @@ -120,7 +119,6 @@ gmi@70090000 { reset-names = "gmi"; ranges = <4 0 0xd0000000 0xfffffff>; - can@4,0 { reg = <4 0 0x100>; nvidia,snor-mux-mode; diff --git a/Documentation/devicetree/bindings/clock/imx6sll-clock.txt b/Documentation/devicetree/bindings/clock/imx6sll-clock.txt new file mode 100644 index 000000000000..fee849d5fdd1 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx6sll-clock.txt @@ -0,0 +1,36 @@ +* Clock bindings for Freescale i.MX6 SLL + +Required properties: +- compatible: Should be "fsl,imx6sll-ccm" +- reg: Address and length of the register set +- #clock-cells: Should be <1> +- clocks: list of clock specifiers, must contain an entry for each required + entry in clock-names +- clock-names: should include entries "ckil", "osc", "ipp_di0" and "ipp_di1" + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx6sll-clock.h +for the full list of i.MX6 SLL clock IDs. + +Examples: + +#include <dt-bindings/clock/imx6sll-clock.h> + +clks: clock-controller@20c4000 { + compatible = "fsl,imx6sll-ccm"; + reg = <0x020c4000 0x4000>; + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; + #clock-cells = <1>; + clocks = <&ckil>, <&osc>, <&ipp_di0>, <&ipp_di1>; + clock-names = "ckil", "osc", "ipp_di0", "ipp_di1"; +}; + +uart1: serial@2020000 { + compatible = "fsl,imx6sl-uart", "fsl,imx6q-uart", "fsl,imx21-uart"; + reg = <0x02020000 0x4000>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6SLL_CLK_UART1_IPG>, + <&clks IMX6SLL_CLK_UART1_SERIAL>; + clock-names = "ipg", "per"; +}; diff --git a/Documentation/devicetree/bindings/clock/intc_stratix10.txt b/Documentation/devicetree/bindings/clock/intc_stratix10.txt new file mode 100644 index 000000000000..9f4ec5cb5c6b --- /dev/null +++ b/Documentation/devicetree/bindings/clock/intc_stratix10.txt @@ -0,0 +1,20 @@ +Device Tree Clock bindings for Intel's SoCFPGA Stratix10 platform + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be + "intel,stratix10-clkmgr" + +- reg : shall be the control register offset from CLOCK_MANAGER's base for the clock. + +- #clock-cells : from common clock binding, shall be set to 1. + +Example: + clkmgr: clock-controller@ffd10000 { + compatible = "intel,stratix10-clkmgr"; + reg = <0xffd10000 0x1000>; + #clock-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt index f1890d0777a6..773a5226342f 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt @@ -22,7 +22,9 @@ Required Properties: - "renesas,r8a7794-cpg-mssr" for the r8a7794 SoC (R-Car E2) - "renesas,r8a7795-cpg-mssr" for the r8a7795 SoC (R-Car H3) - "renesas,r8a7796-cpg-mssr" for the r8a7796 SoC (R-Car M3-W) + - "renesas,r8a77965-cpg-mssr" for the r8a77965 SoC (R-Car M3-N) - "renesas,r8a77970-cpg-mssr" for the r8a77970 SoC (R-Car V3M) + - "renesas,r8a77980-cpg-mssr" for the r8a77980 SoC (R-Car V3H) - "renesas,r8a77995-cpg-mssr" for the r8a77995 SoC (R-Car D3) - reg: Base address and length of the memory resource used by the CPG/MSSR @@ -32,8 +34,8 @@ Required Properties: clock-names - clock-names: List of external parent clock names. Valid names are: - "extal" (r8a7743, r8a7745, r8a7790, r8a7791, r8a7792, r8a7793, r8a7794, - r8a7795, r8a7796, r8a77970, r8a77995) - - "extalr" (r8a7795, r8a7796, r8a77970) + r8a7795, r8a7796, r8a77965, r8a77970, r8a77980, r8a77995) + - "extalr" (r8a7795, r8a7796, r8a77965, r8a77970, r8a77980) - "usb_extal" (r8a7743, r8a7745, r8a7790, r8a7791, r8a7793, r8a7794) - #clock-cells: Must be 2 diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt index e71c675ba5da..904ae682ea90 100644 --- a/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt @@ -32,6 +32,7 @@ clock-output-names: - "clkin_i2s" - external I2S clock - optional, - "gmac_clkin" - external GMAC clock - optional - "phy_50m_out" - output clock of the pll in the mac phy + - "hdmi_phy" - output clock of the hdmi phy pll - optional Example: Clock controller node: diff --git a/Documentation/devicetree/bindings/clock/silabs,si544.txt b/Documentation/devicetree/bindings/clock/silabs,si544.txt new file mode 100644 index 000000000000..b86535b80920 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/silabs,si544.txt @@ -0,0 +1,25 @@ +Binding for Silicon Labs 544 programmable I2C clock generator. + +Reference +This binding uses the common clock binding[1]. Details about the device can be +found in the datasheet[2]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Si544 datasheet + https://www.silabs.com/documents/public/data-sheets/si544-datasheet.pdf + +Required properties: + - compatible: One of "silabs,si514a", "silabs,si514b" "silabs,si514c" according + to the speed grade of the chip. + - reg: I2C device address. + - #clock-cells: From common clock bindings: Shall be 0. + +Optional properties: + - clock-output-names: From common clock bindings. Recommended to be "si544". + +Example: + si544: clock-controller@55 { + reg = <0x55>; + #clock-cells = <0>; + compatible = "silabs,si544b"; + }; diff --git a/Documentation/devicetree/bindings/clock/st,stm32mp1-rcc.txt b/Documentation/devicetree/bindings/clock/st,stm32mp1-rcc.txt new file mode 100644 index 000000000000..fb9495ea582c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st,stm32mp1-rcc.txt @@ -0,0 +1,60 @@ +STMicroelectronics STM32 Peripheral Reset Clock Controller +========================================================== + +The RCC IP is both a reset and a clock controller. + +RCC makes also power management (resume/supend and wakeup interrupt). + +Please also refer to reset.txt for common reset controller binding usage. + +Please also refer to clock-bindings.txt for common clock controller +binding usage. + + +Required properties: +- compatible: "st,stm32mp1-rcc", "syscon" +- reg: should be register base and length as documented in the datasheet +- #clock-cells: 1, device nodes should specify the clock in their + "clocks" property, containing a phandle to the clock device node, + an index specifying the clock to use. +- #reset-cells: Shall be 1 +- interrupts: Should contain a general interrupt line and a interrupt line + to the wake-up of processor (CSTOP). + +Example: + rcc: rcc@50000000 { + compatible = "st,stm32mp1-rcc", "syscon"; + reg = <0x50000000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + interrupts = <GIC_SPI 5 IRQ_TYPE_NONE>, + <GIC_SPI 145 IRQ_TYPE_NONE>; + }; + +Specifying clocks +================= + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/stm32mp1-clks.h header and can be used in device +tree sources. + +Specifying softreset control of devices +======================================= + +Device nodes should specify the reset channel required in their "resets" +property, containing a phandle to the reset device node and an index specifying +which channel to use. +The index is the bit number within the RCC registers bank, starting from RCC +base address. +It is calculated as: index = register_offset / 4 * 32 + bit_offset. +Where bit_offset is the bit offset within the register. + +For example on STM32MP1, for LTDC reset: + ltdc = APB4_RSTSETR_offset / 4 * 32 + LTDC_bit_offset + = 0x180 / 4 * 32 + 0 = 3072 + +The list of valid indices for STM32MP1 is available in: +include/dt-bindings/reset-controller/stm32mp1-resets.h + +This file implements defines like: +#define LTDC_R 3072 diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt index 4ca21c3a6fc9..460ef27b1008 100644 --- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt +++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt @@ -20,6 +20,7 @@ Required properties : - "allwinner,sun50i-a64-ccu" - "allwinner,sun50i-a64-r-ccu" - "allwinner,sun50i-h5-ccu" + - "allwinner,sun50i-h6-ccu" - "nextthing,gr8-ccu" - reg: Must contain the registers base address and length @@ -31,6 +32,9 @@ Required properties : - #clock-cells : must contain 1 - #reset-cells : must contain 1 +For the main CCU on H6, one more clock is needed: +- "iosc": the SoC's internal frequency oscillator + For the PRCM CCUs on A83T/H3/A64, two more clocks are needed: - "pll-periph": the SoC's peripheral PLL from the main CCU - "iosc": the SoC's internal frequency oscillator diff --git a/Documentation/devicetree/bindings/clock/ti/davinci/da8xx-cfgchip.txt b/Documentation/devicetree/bindings/clock/ti/davinci/da8xx-cfgchip.txt new file mode 100644 index 000000000000..1e03dce99a8f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/davinci/da8xx-cfgchip.txt @@ -0,0 +1,93 @@ +Binding for TI DA8XX/OMAP-L13X/AM17XX/AM18XX CFGCHIP clocks + +TI DA8XX/OMAP-L13X/AM17XX/AM18XX SoCs contain a general purpose set of +registers call CFGCHIPn. Some of these registers function as clock +gates. This document describes the bindings for those clocks. + +All of the clock nodes described below must be child nodes of a CFGCHIP node +(compatible = "ti,da830-cfgchip"). + +USB PHY clocks +-------------- +Required properties: +- compatible: shall be "ti,da830-usb-phy-clocks". +- #clock-cells: from common clock binding; shall be set to 1. +- clocks: phandles to the parent clocks corresponding to clock-names +- clock-names: shall be "fck", "usb_refclkin", "auxclk" + +This node provides two clocks. The clock at index 0 is the USB 2.0 PHY 48MHz +clock and the clock at index 1 is the USB 1.1 PHY 48MHz clock. + +eHRPWM Time Base Clock (TBCLK) +------------------------------ +Required properties: +- compatible: shall be "ti,da830-tbclksync". +- #clock-cells: from common clock binding; shall be set to 0. +- clocks: phandle to the parent clock +- clock-names: shall be "fck" + +PLL DIV4.5 divider +------------------ +Required properties: +- compatible: shall be "ti,da830-div4p5ena". +- #clock-cells: from common clock binding; shall be set to 0. +- clocks: phandle to the parent clock +- clock-names: shall be "pll0_pllout" + +EMIFA clock source (ASYNC1) +--------------------------- +Required properties: +- compatible: shall be "ti,da850-async1-clksrc". +- #clock-cells: from common clock binding; shall be set to 0. +- clocks: phandles to the parent clocks corresponding to clock-names +- clock-names: shall be "pll0_sysclk3", "div4.5" + +ASYNC3 clock source +------------------- +Required properties: +- compatible: shall be "ti,da850-async3-clksrc". +- #clock-cells: from common clock binding; shall be set to 0. +- clocks: phandles to the parent clocks corresponding to clock-names +- clock-names: shall be "pll0_sysclk2", "pll1_sysclk2" + +Examples: + + cfgchip: syscon@1417c { + compatible = "ti,da830-cfgchip", "syscon", "simple-mfd"; + reg = <0x1417c 0x14>; + + usb_phy_clk: usb-phy-clocks { + compatible = "ti,da830-usb-phy-clocks"; + #clock-cells = <1>; + clocks = <&psc1 1>, <&usb_refclkin>, <&pll0_auxclk>; + clock-names = "fck", "usb_refclkin", "auxclk"; + }; + ehrpwm_tbclk: ehrpwm_tbclk { + compatible = "ti,da830-tbclksync"; + #clock-cells = <0>; + clocks = <&psc1 17>; + clock-names = "fck"; + }; + div4p5_clk: div4.5 { + compatible = "ti,da830-div4p5ena"; + #clock-cells = <0>; + clocks = <&pll0_pllout>; + clock-names = "pll0_pllout"; + }; + async1_clk: async1 { + compatible = "ti,da850-async1-clksrc"; + #clock-cells = <0>; + clocks = <&pll0_sysclk 3>, <&div4p5_clk>; + clock-names = "pll0_sysclk3", "div4.5"; + }; + async3_clk: async3 { + compatible = "ti,da850-async3-clksrc"; + #clock-cells = <0>; + clocks = <&pll0_sysclk 2>, <&pll1_sysclk 2>; + clock-names = "pll0_sysclk2", "pll1_sysclk2"; + }; + }; + +Also see: +- Documentation/devicetree/bindings/clock/clock-bindings.txt + diff --git a/Documentation/devicetree/bindings/clock/ti/davinci/pll.txt b/Documentation/devicetree/bindings/clock/ti/davinci/pll.txt new file mode 100644 index 000000000000..36998e184821 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/davinci/pll.txt @@ -0,0 +1,96 @@ +Binding for TI DaVinci PLL Controllers + +The PLL provides clocks to most of the components on the SoC. In addition +to the PLL itself, this controller also contains bypasses, gates, dividers, +an multiplexers for various clock signals. + +Required properties: +- compatible: shall be one of: + - "ti,da850-pll0" for PLL0 on DA850/OMAP-L138/AM18XX + - "ti,da850-pll1" for PLL1 on DA850/OMAP-L138/AM18XX +- reg: physical base address and size of the controller's register area. +- clocks: phandles corresponding to the clock names +- clock-names: names of the clock sources - depends on compatible string + - for "ti,da850-pll0", shall be "clksrc", "extclksrc" + - for "ti,da850-pll1", shall be "clksrc" + +Optional properties: +- ti,clkmode-square-wave: Indicates that the the board is supplying a square + wave input on the OSCIN pin instead of using a crystal oscillator. + This property is only valid when compatible = "ti,da850-pll0". + + +Optional child nodes: + +pllout + Describes the main PLL clock output (before POSTDIV). The node name must + be "pllout". + + Required properties: + - #clock-cells: shall be 0 + +sysclk + Describes the PLLDIVn divider clocks that provide the SYSCLKn clock + domains. The node name must be "sysclk". Consumers of this node should + use "n" in "SYSCLKn" as the index parameter for the clock cell. + + Required properties: + - #clock-cells: shall be 1 + +auxclk + Describes the AUXCLK output of the PLL. The node name must be "auxclk". + This child node is only valid when compatible = "ti,da850-pll0". + + Required properties: + - #clock-cells: shall be 0 + +obsclk + Describes the OBSCLK output of the PLL. The node name must be "obsclk". + + Required properties: + - #clock-cells: shall be 0 + + +Examples: + + pll0: clock-controller@11000 { + compatible = "ti,da850-pll0"; + reg = <0x11000 0x1000>; + clocks = <&ref_clk>, <&pll1_sysclk 3>; + clock-names = "clksrc", "extclksrc"; + ti,clkmode-square-wave; + + pll0_pllout: pllout { + #clock-cells = <0>; + }; + + pll0_sysclk: sysclk { + #clock-cells = <1>; + }; + + pll0_auxclk: auxclk { + #clock-cells = <0>; + }; + + pll0_obsclk: obsclk { + #clock-cells = <0>; + }; + }; + + pll1: clock-controller@21a000 { + compatible = "ti,da850-pll1"; + reg = <0x21a000 0x1000>; + clocks = <&ref_clk>; + clock-names = "clksrc"; + + pll0_sysclk: sysclk { + #clock-cells = <1>; + }; + + pll0_obsclk: obsclk { + #clock-cells = <0>; + }; + }; + +Also see: +- Documentation/devicetree/bindings/clock/clock-bindings.txt diff --git a/Documentation/devicetree/bindings/clock/ti/davinci/psc.txt b/Documentation/devicetree/bindings/clock/ti/davinci/psc.txt new file mode 100644 index 000000000000..dae4ad8e198c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/davinci/psc.txt @@ -0,0 +1,71 @@ +Binding for TI DaVinci Power Sleep Controller (PSC) + +The PSC provides power management, clock gating and reset functionality. It is +primarily used for clocking. + +Required properties: +- compatible: shall be one of: + - "ti,da850-psc0" for PSC0 on DA850/OMAP-L138/AM18XX + - "ti,da850-psc1" for PSC1 on DA850/OMAP-L138/AM18XX +- reg: physical base address and size of the controller's register area +- #clock-cells: from common clock binding; shall be set to 1 +- #power-domain-cells: from generic power domain binding; shall be set to 1. +- clocks: phandles to clocks corresponding to the clock-names property +- clock-names: list of parent clock names - depends on compatible value + - for "ti,da850-psc0", shall be "pll0_sysclk1", "pll0_sysclk2", + "pll0_sysclk4", "pll0_sysclk6", "async1" + - for "ti,da850-psc1", shall be "pll0_sysclk2", "pll0_sysclk4", "async3" + +Optional properties: +- #reset-cells: from reset binding; shall be set to 1 - only applicable when + at least one local domain provides a local reset. + +Consumers: + + Clock, power domain and reset consumers shall use the local power domain + module ID (LPSC) as the index corresponding to the clock cell. Refer to + the device-specific datasheet to find these numbers. NB: Most local + domains only provide a clock/power domain and not a reset. + +Examples: + + psc0: clock-controller@10000 { + compatible = "ti,da850-psc0"; + reg = <0x10000 0x1000>; + #clock-cells = <1>; + #power-domain-cells = <1>; + #reset-cells = <1>; + clocks = <&pll0_sysclk 1>, <&pll0_sysclk 2>, + <&pll0_sysclk 4>, <&pll0_sysclk 6>, <&async1_clk>; + clock_names = "pll0_sysclk1", "pll0_sysclk2", + "pll0_sysclk4", "pll0_sysclk6", "async1"; + }; + psc1: clock-controller@227000 { + compatible = "ti,da850-psc1"; + reg = <0x227000 0x1000>; + #clock-cells = <1>; + #power-domain-cells = <1>; + clocks = <&pll0_sysclk 2>, <&pll0_sysclk 4>, <&async3_clk>; + clock_names = "pll0_sysclk2", "pll0_sysclk4", "async3"; + }; + + /* consumer */ + dsp: dsp@11800000 { + compatible = "ti,da850-dsp"; + reg = <0x11800000 0x40000>, + <0x11e00000 0x8000>, + <0x11f00000 0x8000>, + <0x01c14044 0x4>, + <0x01c14174 0x8>; + reg-names = "l2sram", "l1pram", "l1dram", "host1cfg", "chipsig"; + interrupt-parent = <&intc>; + interrupts = <28>; + clocks = <&psc0 15>; + power-domains = <&psc0 15>; + resets = <&psc0 15>; + }; + +Also see: +- Documentation/devicetree/bindings/clock/clock-bindings.txt +- Documentation/devicetree/bindings/power/power_domain.txt +- Documentation/devicetree/bindings/reset/reset.txt diff --git a/Documentation/devicetree/bindings/clock/ti/divider.txt b/Documentation/devicetree/bindings/clock/ti/divider.txt index 35a6f5c7e5c2..9b13b32974f9 100644 --- a/Documentation/devicetree/bindings/clock/ti/divider.txt +++ b/Documentation/devicetree/bindings/clock/ti/divider.txt @@ -75,6 +75,9 @@ Optional properties: - ti,invert-autoidle-bit : autoidle is enabled by setting the bit to 0, see [2] - ti,set-rate-parent : clk_set_rate is propagated to parent +- ti,latch-bit : latch the divider value to HW, only needed if the register + access requires this. As an example dra76x DPLL_GMAC H14 divider implements + such behavior. Examples: dpll_usb_m2_ck: dpll_usb_m2_ck@4a008190 { diff --git a/Documentation/devicetree/bindings/clock/ti/mux.txt b/Documentation/devicetree/bindings/clock/ti/mux.txt index 2d0d170f8001..eec8994b9be8 100644 --- a/Documentation/devicetree/bindings/clock/ti/mux.txt +++ b/Documentation/devicetree/bindings/clock/ti/mux.txt @@ -48,6 +48,9 @@ Optional properties: zero - ti,set-rate-parent : clk_set_rate is propagated to parent clock, not supported by the composite-mux-clock subtype +- ti,latch-bit : latch the mux value to HW, only needed if the register + access requires this. As an example, dra7x DPLL_GMAC H14 muxing + implements such behavior. Examples: diff --git a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt index 76aec8a3724d..3c1f3a229eab 100644 --- a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt +++ b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt @@ -415,12 +415,27 @@ Secure Non-Volatile Storage (SNVS) Low Power (LP) RTC Node value type: <u32> Definition: LP register offset. default it is 0x34. + - clocks + Usage: optional, required if SNVS LP RTC requires explicit + enablement of clocks + Value type: <prop_encoded-array> + Definition: a clock specifier describing the clock required for + enabling and disabling SNVS LP RTC. + + - clock-names + Usage: optional, required if SNVS LP RTC requires explicit + enablement of clocks + Value type: <string> + Definition: clock name string should be "snvs-rtc". + EXAMPLE sec_mon_rtc_lp@1 { compatible = "fsl,sec-v4.0-mon-rtc-lp"; interrupts = <93 2>; regmap = <&snvs>; offset = <0x34>; + clocks = <&clks IMX7D_SNVS_CLK>; + clock-names = "snvs-rtc"; }; ===================================================================== @@ -543,6 +558,8 @@ FULL EXAMPLE regmap = <&sec_mon>; offset = <0x34>; interrupts = <93 2>; + clocks = <&clks IMX7D_SNVS_CLK>; + clock-names = "snvs-rtc"; }; snvs-pwrkey@020cc000 { diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt index 0047b1394c70..2c887536258c 100644 --- a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt +++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt @@ -14,7 +14,13 @@ Required properties: "adi,adv7513" "adi,adv7533" -- reg: I2C slave address +- reg: I2C slave addresses + The ADV7511 internal registers are split into four pages exposed through + different I2C addresses, creating four register maps. Each map has it own + I2C address and acts as a standard slave device on the I2C bus. The main + address is mandatory, others are optional and revert to defaults if not + specified. + The ADV7511 supports a large number of input data formats that differ by their color depth, color format, clock mode, bit justification and random @@ -70,6 +76,9 @@ Optional properties: rather than generate its own timings for HDMI output. - clocks: from common clock binding: reference to the CEC clock. - clock-names: from common clock binding: must be "cec". +- reg-names : Names of maps with programmable addresses. + It can contain any map needing a non-default address. + Possible maps names are : "main", "edid", "cec", "packet" Required nodes: @@ -88,7 +97,12 @@ Example adv7511w: hdmi@39 { compatible = "adi,adv7511w"; - reg = <39>; + /* + * The EDID page will be accessible on address 0x66 on the I2C + * bus. All other maps continue to use their default addresses. + */ + reg = <0x39>, <0x66>; + reg-names = "main", "edid"; interrupt-parent = <&gpio3>; interrupts = <29 IRQ_TYPE_EDGE_FALLING>; clocks = <&cec_clock>; diff --git a/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt b/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt new file mode 100644 index 000000000000..f5725bb6c61c --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt @@ -0,0 +1,133 @@ +Cadence DSI bridge +================== + +The Cadence DSI bridge is a DPI to DSI bridge supporting up to 4 DSI lanes. + +Required properties: +- compatible: should be set to "cdns,dsi". +- reg: physical base address and length of the controller's registers. +- interrupts: interrupt line connected to the DSI bridge. +- clocks: DSI bridge clocks. +- clock-names: must contain "dsi_p_clk" and "dsi_sys_clk". +- phys: phandle link to the MIPI D-PHY controller. +- phy-names: must contain "dphy". +- #address-cells: must be set to 1. +- #size-cells: must be set to 0. + +Optional properties: +- resets: DSI reset lines. +- reset-names: can contain "dsi_p_rst". + +Required subnodes: +- ports: Ports as described in Documentation/devicetree/bindings/graph.txt. + 2 ports are available: + * port 0: this port is only needed if some of your DSI devices are + controlled through an external bus like I2C or SPI. Can have at + most 4 endpoints. The endpoint number is directly encoding the + DSI virtual channel used by this device. + * port 1: represents the DPI input. + Other ports will be added later to support the new kind of inputs. + +- one subnode per DSI device connected on the DSI bus. Each DSI device should + contain a reg property encoding its virtual channel. + +Cadence DPHY +============ + +Cadence DPHY block. + +Required properties: +- compatible: should be set to "cdns,dphy". +- reg: physical base address and length of the DPHY registers. +- clocks: DPHY reference clocks. +- clock-names: must contain "psm" and "pll_ref". +- #phy-cells: must be set to 0. + + +Example: + dphy0: dphy@fd0e0000{ + compatible = "cdns,dphy"; + reg = <0x0 0xfd0e0000 0x0 0x1000>; + clocks = <&psm_clk>, <&pll_ref_clk>; + clock-names = "psm", "pll_ref"; + #phy-cells = <0>; + }; + + dsi0: dsi@fd0c0000 { + compatible = "cdns,dsi"; + reg = <0x0 0xfd0c0000 0x0 0x1000>; + clocks = <&pclk>, <&sysclk>; + clock-names = "dsi_p_clk", "dsi_sys_clk"; + interrupts = <1>; + phys = <&dphy0>; + phy-names = "dphy"; + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + dsi0_dpi_input: endpoint { + remote-endpoint = <&xxx_dpi_output>; + }; + }; + }; + + panel: dsi-dev@0 { + compatible = "<vendor,panel>"; + reg = <0>; + }; + }; + +or + + dsi0: dsi@fd0c0000 { + compatible = "cdns,dsi"; + reg = <0x0 0xfd0c0000 0x0 0x1000>; + clocks = <&pclk>, <&sysclk>; + clock-names = "dsi_p_clk", "dsi_sys_clk"; + interrupts = <1>; + phys = <&dphy1>; + phy-names = "dphy"; + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + dsi0_output: endpoint@0 { + reg = <0>; + remote-endpoint = <&dsi_panel_input>; + }; + }; + + port@1 { + reg = <1>; + dsi0_dpi_input: endpoint { + remote-endpoint = <&xxx_dpi_output>; + }; + }; + }; + }; + + i2c@xxx { + panel: panel@59 { + compatible = "<vendor,panel>"; + reg = <0x59>; + + port { + dsi_panel_input: endpoint { + remote-endpoint = <&dsi0_output>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt index 3a72a103a18a..a41d280c3f9f 100644 --- a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt +++ b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt @@ -14,6 +14,7 @@ Required properties: - compatible : Shall contain one or more of - "renesas,r8a7795-hdmi" for R8A7795 (R-Car H3) compatible HDMI TX - "renesas,r8a7796-hdmi" for R8A7796 (R-Car M3-W) compatible HDMI TX + - "renesas,r8a77965-hdmi" for R8A77965 (R-Car M3-N) compatible HDMI TX - "renesas,rcar-gen3-hdmi" for the generic R-Car Gen3 compatible HDMI TX When compatible with generic versions, nodes must list the SoC-specific diff --git a/Documentation/devicetree/bindings/display/bridge/tda998x.txt b/Documentation/devicetree/bindings/display/bridge/tda998x.txt index 24cc2466185a..1a4eaca40d94 100644 --- a/Documentation/devicetree/bindings/display/bridge/tda998x.txt +++ b/Documentation/devicetree/bindings/display/bridge/tda998x.txt @@ -27,6 +27,9 @@ Optional properties: in question is used. The implementation allows one or two DAIs. If two DAIs are defined, they must be of different type. + - nxp,calib-gpios: calibration GPIO, which must correspond with the + gpio used for the TDA998x interrupt pin. + [1] Documentation/sound/alsa/soc/DAI.txt [2] include/dt-bindings/display/tda998x.h diff --git a/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt new file mode 100644 index 000000000000..37f0c04d5a28 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt @@ -0,0 +1,60 @@ +Thine Electronics THC63LVD1024 LVDS decoder +------------------------------------------- + +The THC63LVD1024 is a dual link LVDS receiver designed to convert LVDS streams +to parallel data outputs. The chip supports single/dual input/output modes, +handling up to two LVDS input streams and up to two digital CMOS/TTL outputs. + +Single or dual operation mode, output data mapping and DDR output modes are +configured through input signals and the chip does not expose any control bus. + +Required properties: +- compatible: Shall be "thine,thc63lvd1024" +- vcc-supply: Power supply for TTL output, TTL CLOCKOUT signal, LVDS input, + PPL and digital circuitry + +Optional properties: +- powerdown-gpios: Power down GPIO signal, pin name "/PDWN". Active low +- oe-gpios: Output enable GPIO signal, pin name "OE". Active high + +The THC63LVD1024 video port connections are modeled according +to OF graph bindings specified by Documentation/devicetree/bindings/graph.txt + +Required video port nodes: +- port@0: First LVDS input port +- port@2: First digital CMOS/TTL parallel output + +Optional video port nodes: +- port@1: Second LVDS input port +- port@3: Second digital CMOS/TTL parallel output + +Example: +-------- + + thc63lvd1024: lvds-decoder { + compatible = "thine,thc63lvd1024"; + + vcc-supply = <®_lvds_vcc>; + powerdown-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + lvds_dec_in_0: endpoint { + remote-endpoint = <&lvds_out>; + }; + }; + + port@2{ + reg = <2>; + + lvds_dec_out_2: endpoint { + remote-endpoint = <&adv7511_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt b/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt index fc2588292a68..775193e1c641 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt @@ -19,7 +19,8 @@ Required properties: clock-names property. - clock-names: list of clock names sorted in the same order as the clocks property. Must contain "pclk", "aclk_decon", "aclk_smmu_decon0x", - "aclk_xiu_decon0x", "pclk_smmu_decon0x", clk_decon_vclk", + "aclk_xiu_decon0x", "pclk_smmu_decon0x", "aclk_smmu_decon1x", + "aclk_xiu_decon1x", "pclk_smmu_decon1x", clk_decon_vclk", "sclk_decon_eclk" - ports: contains a port which is connected to mic node. address-cells and size-cells must 1 and 0, respectively. @@ -34,10 +35,14 @@ decon: decon@13800000 { clocks = <&cmu_disp CLK_ACLK_DECON>, <&cmu_disp CLK_ACLK_SMMU_DECON0X>, <&cmu_disp CLK_ACLK_XIU_DECON0X>, <&cmu_disp CLK_PCLK_SMMU_DECON0X>, + <&cmu_disp CLK_ACLK_SMMU_DECON1X>, + <&cmu_disp CLK_ACLK_XIU_DECON1X>, + <&cmu_disp CLK_PCLK_SMMU_DECON1X>, <&cmu_disp CLK_SCLK_DECON_VCLK>, <&cmu_disp CLK_SCLK_DECON_ECLK>; clock-names = "aclk_decon", "aclk_smmu_decon0x", "aclk_xiu_decon0x", - "pclk_smmu_decon0x", "sclk_decon_vclk", "sclk_decon_eclk"; + "pclk_smmu_decon0x", "aclk_smmu_decon1x", "aclk_xiu_decon1x", + "pclk_smmu_decon1x", "sclk_decon_vclk", "sclk_decon_eclk"; interrupt-names = "vsync", "lcd_sys"; interrupts = <0 202 0>, <0 203 0>; diff --git a/Documentation/devicetree/bindings/display/panel/panel-common.txt b/Documentation/devicetree/bindings/display/panel/panel-common.txt index 557fa765adcb..5d2519af4bb5 100644 --- a/Documentation/devicetree/bindings/display/panel/panel-common.txt +++ b/Documentation/devicetree/bindings/display/panel/panel-common.txt @@ -38,7 +38,7 @@ Display Timings require specific display timings. The panel-timing subnode expresses those timings as specified in the timing subnode section of the display timing bindings defined in - Documentation/devicetree/bindings/display/display-timing.txt. + Documentation/devicetree/bindings/display/panel/display-timing.txt. Connectivity diff --git a/Documentation/devicetree/bindings/display/renesas,du.txt b/Documentation/devicetree/bindings/display/renesas,du.txt index c9cd17f99702..7c6854bd0a04 100644 --- a/Documentation/devicetree/bindings/display/renesas,du.txt +++ b/Documentation/devicetree/bindings/display/renesas,du.txt @@ -13,6 +13,7 @@ Required Properties: - "renesas,du-r8a7794" for R8A7794 (R-Car E2) compatible DU - "renesas,du-r8a7795" for R8A7795 (R-Car H3) compatible DU - "renesas,du-r8a7796" for R8A7796 (R-Car M3-W) compatible DU + - "renesas,du-r8a77965" for R8A77965 (R-Car M3-N) compatible DU - "renesas,du-r8a77970" for R8A77970 (R-Car V3M) compatible DU - "renesas,du-r8a77995" for R8A77995 (R-Car D3) compatible DU @@ -47,20 +48,21 @@ bindings specified in Documentation/devicetree/bindings/graph.txt. The following table lists for each supported model the port number corresponding to each DU output. - Port0 Port1 Port2 Port3 + Port0 Port1 Port2 Port3 ----------------------------------------------------------------------------- - R8A7743 (RZ/G1M) DPAD 0 LVDS 0 - - - R8A7745 (RZ/G1E) DPAD 0 DPAD 1 - - - R8A7779 (R-Car H1) DPAD 0 DPAD 1 - - - R8A7790 (R-Car H2) DPAD 0 LVDS 0 LVDS 1 - - R8A7791 (R-Car M2-W) DPAD 0 LVDS 0 - - - R8A7792 (R-Car V2H) DPAD 0 DPAD 1 - - - R8A7793 (R-Car M2-N) DPAD 0 LVDS 0 - - - R8A7794 (R-Car E2) DPAD 0 DPAD 1 - - - R8A7795 (R-Car H3) DPAD 0 HDMI 0 HDMI 1 LVDS 0 - R8A7796 (R-Car M3-W) DPAD 0 HDMI 0 LVDS 0 - - R8A77970 (R-Car V3M) DPAD 0 LVDS 0 - - - R8A77995 (R-Car D3) DPAD 0 LVDS 0 LVDS 1 - + R8A7743 (RZ/G1M) DPAD 0 LVDS 0 - - + R8A7745 (RZ/G1E) DPAD 0 DPAD 1 - - + R8A7779 (R-Car H1) DPAD 0 DPAD 1 - - + R8A7790 (R-Car H2) DPAD 0 LVDS 0 LVDS 1 - + R8A7791 (R-Car M2-W) DPAD 0 LVDS 0 - - + R8A7792 (R-Car V2H) DPAD 0 DPAD 1 - - + R8A7793 (R-Car M2-N) DPAD 0 LVDS 0 - - + R8A7794 (R-Car E2) DPAD 0 DPAD 1 - - + R8A7795 (R-Car H3) DPAD 0 HDMI 0 HDMI 1 LVDS 0 + R8A7796 (R-Car M3-W) DPAD 0 HDMI 0 LVDS 0 - + R8A77965 (R-Car M3-N) DPAD 0 HDMI 0 LVDS 0 - + R8A77970 (R-Car V3M) DPAD 0 LVDS 0 - - + R8A77995 (R-Car D3) DPAD 0 LVDS 0 LVDS 1 - Example: R8A7795 (R-Car H3) ES2.0 DU diff --git a/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt new file mode 100644 index 000000000000..6a6cf5de08b0 --- /dev/null +++ b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt @@ -0,0 +1,93 @@ +Allwinner A31 DSI Encoder +========================= + +The DSI pipeline consists of two separate blocks: the DSI controller +itself, and its associated D-PHY. + +DSI Encoder +----------- + +The DSI Encoder generates the DSI signal from the TCON's. + +Required properties: + - compatible: value must be one of: + * allwinner,sun6i-a31-mipi-dsi + - reg: base address and size of memory-mapped region + - interrupts: interrupt associated to this IP + - clocks: phandles to the clocks feeding the DSI encoder + * bus: the DSI interface clock + * mod: the DSI module clock + - clock-names: the clock names mentioned above + - phys: phandle to the D-PHY + - phy-names: must be "dphy" + - resets: phandle to the reset controller driving the encoder + + - ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoint, usually coming from the + associated TCON. + +Any MIPI-DSI device attached to this should be described according to +the bindings defined in ../mipi-dsi-bus.txt + +D-PHY +----- + +Required properties: + - compatible: value must be one of: + * allwinner,sun6i-a31-mipi-dphy + - reg: base address and size of memory-mapped region + - clocks: phandles to the clocks feeding the DSI encoder + * bus: the DSI interface clock + * mod: the DSI module clock + - clock-names: the clock names mentioned above + - resets: phandle to the reset controller driving the encoder + +Example: + +dsi0: dsi@1ca0000 { + compatible = "allwinner,sun6i-a31-mipi-dsi"; + reg = <0x01ca0000 0x1000>; + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_MIPI_DSI>, + <&ccu CLK_DSI_SCLK>; + clock-names = "bus", "mod"; + resets = <&ccu RST_BUS_MIPI_DSI>; + phys = <&dphy0>; + phy-names = "dphy"; + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "bananapi,lhr050h41", "ilitek,ili9881c"; + reg = <0>; + power-gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; /* PB07 */ + reset-gpios = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL05 */ + backlight = <&pwm_bl>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + dsi0_in_tcon0: endpoint { + remote-endpoint = <&tcon0_out_dsi0>; + }; + }; + }; +}; + +dphy0: d-phy@1ca1000 { + compatible = "allwinner,sun6i-a31-mipi-dphy"; + reg = <0x01ca1000 0x1000>; + clocks = <&ccu CLK_BUS_MIPI_DSI>, + <&ccu CLK_DSI_DPHY>; + clock-names = "bus", "mod"; + resets = <&ccu RST_BUS_MIPI_DSI>; + #phy-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt b/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt index baf9b34d20bf..b6a8cc0978cd 100644 --- a/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt +++ b/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt @@ -74,8 +74,8 @@ Example: bcm2835_i2s: i2s@7e203000 { compatible = "brcm,bcm2835-i2s"; - reg = < 0x7e203000 0x20>, - < 0x7e101098 0x02>; + reg = < 0x7e203000 0x24>; + clocks = <&clocks BCM2835_CLOCK_PCM>; dmas = <&dma 2>, <&dma 3>; diff --git a/Documentation/devicetree/bindings/dma/mtk-hsdma.txt b/Documentation/devicetree/bindings/dma/mtk-hsdma.txt new file mode 100644 index 000000000000..4bb317359dc6 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/mtk-hsdma.txt @@ -0,0 +1,33 @@ +MediaTek High-Speed DMA Controller +================================== + +This device follows the generic DMA bindings defined in dma/dma.txt. + +Required properties: + +- compatible: Must be one of + "mediatek,mt7622-hsdma": for MT7622 SoC + "mediatek,mt7623-hsdma": for MT7623 SoC +- reg: Should contain the register's base address and length. +- interrupts: Should contain a reference to the interrupt used by this + device. +- clocks: Should be the clock specifiers corresponding to the entry in + clock-names property. +- clock-names: Should contain "hsdma" entries. +- power-domains: Phandle to the power domain that the device is part of +- #dma-cells: The length of the DMA specifier, must be <1>. This one cell + in dmas property of a client device represents the channel + number. +Example: + + hsdma: dma-controller@1b007000 { + compatible = "mediatek,mt7623-hsdma"; + reg = <0 0x1b007000 0 0x1000>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_LOW>; + clocks = <ðsys CLK_ETHSYS_HSDMA>; + clock-names = "hsdma"; + power-domains = <&scpsys MT2701_POWER_DOMAIN_ETH>; + #dma-cells = <1>; + }; + +DMA clients must use the format described in dma/dma.txt file. diff --git a/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt b/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt index 9cbf5d9df8fd..cf5b9e44432c 100644 --- a/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt +++ b/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt @@ -15,6 +15,10 @@ Required properties: the secure world. - qcom,controlled-remotely : optional, indicates that the bam is controlled by remote proccessor i.e. execution environment. +- num-channels : optional, indicates supported number of DMA channels in a + remotely controlled bam. +- qcom,num-ees : optional, indicates supported number of Execution Environments + in a remotely controlled bam. Example: diff --git a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt index 891db41e9420..61315eaa7660 100644 --- a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt +++ b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt @@ -18,6 +18,7 @@ Required Properties: Examples with soctypes are: - "renesas,dmac-r8a7743" (RZ/G1M) - "renesas,dmac-r8a7745" (RZ/G1E) + - "renesas,dmac-r8a77470" (RZ/G1C) - "renesas,dmac-r8a7790" (R-Car H2) - "renesas,dmac-r8a7791" (R-Car M2-W) - "renesas,dmac-r8a7792" (R-Car V2H) @@ -25,7 +26,9 @@ Required Properties: - "renesas,dmac-r8a7794" (R-Car E2) - "renesas,dmac-r8a7795" (R-Car H3) - "renesas,dmac-r8a7796" (R-Car M3-W) + - "renesas,dmac-r8a77965" (R-Car M3-N) - "renesas,dmac-r8a77970" (R-Car V3M) + - "renesas,dmac-r8a77980" (R-Car V3H) - reg: base address and length of the registers block for the DMAC diff --git a/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt index f3d1f151ba80..9dc935e24e55 100644 --- a/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt +++ b/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt @@ -11,6 +11,7 @@ Required Properties: - "renesas,r8a7794-usb-dmac" (R-Car E2) - "renesas,r8a7795-usb-dmac" (R-Car H3) - "renesas,r8a7796-usb-dmac" (R-Car M3-W) + - "renesas,r8a77965-usb-dmac" (R-Car M3-N) - reg: base address and length of the registers block for the DMAC - interrupts: interrupt specifiers for the DMAC, one for each entry in interrupt-names. diff --git a/Documentation/devicetree/bindings/dma/snps,dw-axi-dmac.txt b/Documentation/devicetree/bindings/dma/snps,dw-axi-dmac.txt new file mode 100644 index 000000000000..f237b7928283 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/snps,dw-axi-dmac.txt @@ -0,0 +1,41 @@ +Synopsys DesignWare AXI DMA Controller + +Required properties: +- compatible: "snps,axi-dma-1.01a" +- reg: Address range of the DMAC registers. This should include + all of the per-channel registers. +- interrupt: Should contain the DMAC interrupt number. +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device. +- dma-channels: Number of channels supported by hardware. +- snps,dma-masters: Number of AXI masters supported by the hardware. +- snps,data-width: Maximum AXI data width supported by hardware. + (0 - 8bits, 1 - 16bits, 2 - 32bits, ..., 6 - 512bits) +- snps,priority: Priority of channel. Array size is equal to the number of + dma-channels. Priority value must be programmed within [0:dma-channels-1] + range. (0 - minimum priority) +- snps,block-size: Maximum block size supported by the controller channel. + Array size is equal to the number of dma-channels. + +Optional properties: +- snps,axi-max-burst-len: Restrict master AXI burst length by value specified + in this property. If this property is missing the maximum AXI burst length + supported by DMAC is used. [1:256] + +Example: + +dmac: dma-controller@80000 { + compatible = "snps,axi-dma-1.01a"; + reg = <0x80000 0x400>; + clocks = <&core_clk>, <&cfgr_clk>; + clock-names = "core-clk", "cfgr-clk"; + interrupt-parent = <&intc>; + interrupts = <27>; + + dma-channels = <4>; + snps,dma-masters = <2>; + snps,data-width = <3>; + snps,block-size = <4096 4096 4096 4096>; + snps,priority = <0 1 2 3>; + snps,axi-max-burst-len = <16>; +}; diff --git a/Documentation/devicetree/bindings/dma/stm32-dma.txt b/Documentation/devicetree/bindings/dma/stm32-dma.txt index 0b55718bf889..c5f519097204 100644 --- a/Documentation/devicetree/bindings/dma/stm32-dma.txt +++ b/Documentation/devicetree/bindings/dma/stm32-dma.txt @@ -62,14 +62,14 @@ channel: a phandle to the DMA controller plus the following four integer cells: 0x1: medium 0x2: high 0x3: very high -4. A 32bit mask specifying the DMA FIFO threshold configuration which are device - dependent: - -bit 0-1: Fifo threshold +4. A 32bit bitfield value specifying DMA features which are device dependent: + -bit 0-1: DMA FIFO threshold selection 0x0: 1/4 full FIFO 0x1: 1/2 full FIFO 0x2: 3/4 full FIFO 0x3: full FIFO + Example: usart1: serial@40011000 { diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt b/Documentation/devicetree/bindings/edac/socfpga-eccmgr.txt index 4a1714f96bab..5626560a6cfd 100644 --- a/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt +++ b/Documentation/devicetree/bindings/edac/socfpga-eccmgr.txt @@ -231,3 +231,38 @@ Example: <48 IRQ_TYPE_LEVEL_HIGH>; }; }; + +Stratix10 SoCFPGA ECC Manager +The Stratix10 SoC ECC Manager handles the IRQs for each peripheral +in a shared register similar to the Arria10. However, ECC requires +access to registers that can only be read from Secure Monitor with +SMC calls. Therefore the device tree is slightly different. + +Required Properties: +- compatible : Should be "altr,socfpga-s10-ecc-manager" +- interrupts : Should be single bit error interrupt, then double bit error + interrupt. +- interrupt-controller : boolean indicator that ECC Manager is an interrupt controller +- #interrupt-cells : must be set to 2. + +Subcomponents: + +SDRAM ECC +Required Properties: +- compatible : Should be "altr,sdram-edac-s10" +- interrupts : Should be single bit error interrupt, then double bit error + interrupt, in this order. + +Example: + + eccmgr { + compatible = "altr,socfpga-s10-ecc-manager"; + interrupts = <0 15 4>, <0 95 4>; + interrupt-controller; + #interrupt-cells = <2>; + + sdramedac { + compatible = "altr,sdram-edac-s10"; + interrupts = <16 4>, <48 4>; + }; + }; diff --git a/Documentation/devicetree/bindings/eeprom/at24.txt b/Documentation/devicetree/bindings/eeprom/at24.txt index abfae1beca2b..61d833abafbf 100644 --- a/Documentation/devicetree/bindings/eeprom/at24.txt +++ b/Documentation/devicetree/bindings/eeprom/at24.txt @@ -41,12 +41,16 @@ Required properties: "nxp", "ramtron", "renesas", + "rohm", "st", Some vendors use different model names for chips which are just variants of the above. Known such exceptions are listed below: + "nxp,se97b" - the fallback is "atmel,24c02", "renesas,r1ex24002" - the fallback is "atmel,24c02" + "renesas,r1ex24128" - the fallback is "atmel,24c128" + "rohm,br24t01" - the fallback is "atmel,24c01" - reg: The I2C address of the EEPROM. diff --git a/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt b/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt new file mode 100644 index 000000000000..a8c362eb160c --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt @@ -0,0 +1,29 @@ +Lattice MachXO2 Slave SPI FPGA Manager + +Lattice MachXO2 FPGAs support a method of loading the bitstream over +'slave SPI' interface. + +See 'MachXO2ProgrammingandConfigurationUsageGuide.pdf' on www.latticesemi.com + +Required properties: +- compatible: should contain "lattice,machxo2-slave-spi" +- reg: spi chip select of the FPGA + +Example for full FPGA configuration: + + fpga-region0 { + compatible = "fpga-region"; + fpga-mgr = <&fpga_mgr_spi>; + #address-cells = <0x1>; + #size-cells = <0x1>; + }; + + spi1: spi@2000 { + ... + + fpga_mgr_spi: fpga-mgr@0 { + compatible = "lattice,machxo2-slave-spi"; + spi-max-frequency = <8000000>; + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt index ad876548ab5d..c1f65d1dac1d 100644 --- a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt +++ b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt @@ -10,6 +10,7 @@ Required properties: * And, optionally, one of the vendor specific compatible: + allwinner,sun4i-a10-mali + allwinner,sun7i-a20-mali + + allwinner,sun8i-h3-mali + allwinner,sun50i-h5-mali + amlogic,meson-gxbb-mali + amlogic,meson-gxl-mali diff --git a/Documentation/devicetree/bindings/gpu/brcm,bcm-v3d.txt b/Documentation/devicetree/bindings/gpu/brcm,bcm-v3d.txt new file mode 100644 index 000000000000..c907aa8dd755 --- /dev/null +++ b/Documentation/devicetree/bindings/gpu/brcm,bcm-v3d.txt @@ -0,0 +1,28 @@ +Broadcom V3D GPU + +Only the Broadcom V3D 3.x and newer GPUs are covered by this binding. +For V3D 2.x, see brcm,bcm-vc4.txt. + +Required properties: +- compatible: Should be "brcm,7268-v3d" or "brcm,7278-v3d" +- reg: Physical base addresses and lengths of the register areas +- reg-names: Names for the register areas. The "hub", "bridge", and "core0" + register areas are always required. The "gca" register area + is required if the GCA cache controller is present. +- interrupts: The interrupt numbers. The first interrupt is for the hub, + while the following interrupts are for the cores. + See bindings/interrupt-controller/interrupts.txt + +Optional properties: +- clocks: The core clock the unit runs on + +v3d { + compatible = "brcm,7268-v3d"; + reg = <0xf1204000 0x100>, + <0xf1200000 0x4000>, + <0xf1208000 0x4000>, + <0xf1204100 0x100>; + reg-names = "bridge", "hub", "core0", "gca"; + interrupts = <0 78 4>, + <0 77 4>; +}; diff --git a/Documentation/devicetree/bindings/gpu/samsung-scaler.txt b/Documentation/devicetree/bindings/gpu/samsung-scaler.txt new file mode 100644 index 000000000000..9c3d98105dfd --- /dev/null +++ b/Documentation/devicetree/bindings/gpu/samsung-scaler.txt @@ -0,0 +1,27 @@ +* Samsung Exynos Image Scaler + +Required properties: + - compatible : value should be one of the following: + (a) "samsung,exynos5420-scaler" for Scaler IP in Exynos5420 + (b) "samsung,exynos5433-scaler" for Scaler IP in Exynos5433 + + - reg : Physical base address of the IP registers and length of memory + mapped region. + + - interrupts : Interrupt specifier for scaler interrupt, according to format + specific to interrupt parent. + + - clocks : Clock specifier for scaler clock, according to generic clock + bindings. (See Documentation/devicetree/bindings/clock/exynos*.txt) + + - clock-names : Names of clocks. For exynos scaler, it should be "mscl" + on 5420 and "pclk", "aclk" and "aclk_xiu" on 5433. + +Example: + scaler@12800000 { + compatible = "samsung,exynos5420-scaler"; + reg = <0x12800000 0x1294>; + interrupts = <0 220 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clock CLK_MSCL0>; + clock-names = "mscl"; + }; diff --git a/Documentation/devicetree/bindings/hwmon/gpio-fan.txt b/Documentation/devicetree/bindings/hwmon/gpio-fan.txt index 439a7430fc68..2becdcfdc840 100644 --- a/Documentation/devicetree/bindings/hwmon/gpio-fan.txt +++ b/Documentation/devicetree/bindings/hwmon/gpio-fan.txt @@ -11,7 +11,7 @@ Optional properties: must have the RPM values in ascending order. - alarm-gpios: This pin going active indicates something is wrong with the fan, and a udev event will be fired. -- cooling-cells: If used as a cooling device, must be <2> +- #cooling-cells: If used as a cooling device, must be <2> Also see: Documentation/devicetree/bindings/thermal/thermal.txt min and max states are derived from the speed-map of the fan. diff --git a/Documentation/devicetree/bindings/hwmon/ltc2990.txt b/Documentation/devicetree/bindings/hwmon/ltc2990.txt new file mode 100644 index 000000000000..f92f54029e84 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/ltc2990.txt @@ -0,0 +1,36 @@ +ltc2990: Linear Technology LTC2990 power monitor + +Required properties: +- compatible: Must be "lltc,ltc2990" +- reg: I2C slave address +- lltc,meas-mode: + An array of two integers for configuring the chip measurement mode. + + The first integer defines the bits 2..0 in the control register. In all + cases the internal temperature and supply voltage are measured. In + addition the following input measurements are enabled per mode: + + 0: V1, V2, TR2 + 1: V1-V2, TR2 + 2: V1-V2, V3, V4 + 3: TR1, V3, V4 + 4: TR1, V3-V4 + 5: TR1, TR2 + 6: V1-V2, V3-V4 + 7: V1, V2, V3, V4 + + The second integer defines the bits 4..3 in the control register. This + allows a subset of the measurements to be enabled: + + 0: Internal temperature and supply voltage only + 1: TR1, V1 or V1-V2 only per mode + 2: TR2, V3 or V3-V4 only per mode + 3: All measurements per mode + +Example: + +ltc2990@4c { + compatible = "lltc,ltc2990"; + reg = <0x4c>; + lltc,meas-mode = <7 3>; /* V1, V2, V3, V4 */ +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt index a777477e4547..4a7811ecd954 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt @@ -13,7 +13,9 @@ Required properties: "renesas,i2c-r8a7794" if the device is a part of a R8A7794 SoC. "renesas,i2c-r8a7795" if the device is a part of a R8A7795 SoC. "renesas,i2c-r8a7796" if the device is a part of a R8A7796 SoC. + "renesas,i2c-r8a77965" if the device is a part of a R8A77965 SoC. "renesas,i2c-r8a77970" if the device is a part of a R8A77970 SoC. + "renesas,i2c-r8a77995" if the device is a part of a R8A77995 SoC. "renesas,rcar-gen1-i2c" for a generic R-Car Gen1 compatible device. "renesas,rcar-gen2-i2c" for a generic R-Car Gen2 or RZ/G1 compatible device. diff --git a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt index 224390999e81..fc7e17802746 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt @@ -13,6 +13,7 @@ Required properties: - "renesas,iic-r8a7794" (R-Car E2) - "renesas,iic-r8a7795" (R-Car H3) - "renesas,iic-r8a7796" (R-Car M3-W) + - "renesas,iic-r8a77965" (R-Car M3-N) - "renesas,iic-sh73a0" (SH-Mobile AG5) - "renesas,rcar-gen2-iic" (generic R-Car Gen2 or RZ/G1 compatible device) diff --git a/Documentation/devicetree/bindings/i2c/i2c-synquacer.txt b/Documentation/devicetree/bindings/i2c/i2c-synquacer.txt new file mode 100644 index 000000000000..72f4a2f0fedc --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-synquacer.txt @@ -0,0 +1,29 @@ +Socionext SynQuacer I2C + +Required properties: +- compatible : Must be "socionext,synquacer-i2c" +- reg : Offset and length of the register set for the device +- interrupts : A single interrupt specifier +- #address-cells : Must be <1>; +- #size-cells : Must be <0>; +- clock-names : Must contain "pclk". +- clocks : Must contain an entry for each name in clock-names. + (See the common clock bindings.) + +Optional properties: +- clock-frequency : Desired I2C bus clock frequency in Hz. As only Normal and + Fast modes are supported, possible values are 100000 and + 400000. + +Example : + + i2c@51210000 { + compatible = "socionext,synquacer-i2c"; + reg = <0x51210000 0x1000>; + interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clock-names = "pclk"; + clocks = <&clk_i2c>; + clock-frequency = <400000>; + }; diff --git a/Documentation/devicetree/bindings/input/atmel,maxtouch.txt b/Documentation/devicetree/bindings/input/atmel,maxtouch.txt index 23e3abc3fdef..c88919480d37 100644 --- a/Documentation/devicetree/bindings/input/atmel,maxtouch.txt +++ b/Documentation/devicetree/bindings/input/atmel,maxtouch.txt @@ -4,6 +4,13 @@ Required properties: - compatible: atmel,maxtouch + The following compatibles have been used in various products but are + deprecated: + atmel,qt602240_ts + atmel,atmel_mxt_ts + atmel,atmel_mxt_tp + atmel,mXT224 + - reg: The I2C address of the device - interrupts: The sink for the touchpad's IRQ output diff --git a/Documentation/devicetree/bindings/input/elan_i2c.txt b/Documentation/devicetree/bindings/input/elan_i2c.txt index ee3242c4ba67..d80a83583238 100644 --- a/Documentation/devicetree/bindings/input/elan_i2c.txt +++ b/Documentation/devicetree/bindings/input/elan_i2c.txt @@ -14,6 +14,7 @@ Optional properties: - pinctrl-0: a phandle pointing to the pin settings for the device (see pinctrl binding [1]). - vcc-supply: a phandle for the regulator supplying 3.3V power. +- elan,trackpoint: touchpad can support a trackpoint (boolean) [0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt [1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt diff --git a/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt index a83f9a5734ca..89674ad8a097 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt @@ -9,11 +9,12 @@ number of interrupt exposed depends on the SoC. Required properties: -- compatible : must have "amlogic,meson8-gpio-intc” and either - “amlogic,meson8-gpio-intc” for meson8 SoCs (S802) or - “amlogic,meson8b-gpio-intc” for meson8b SoCs (S805) or - “amlogic,meson-gxbb-gpio-intc” for GXBB SoCs (S905) or - “amlogic,meson-gxl-gpio-intc” for GXL SoCs (S905X, S912) +- compatible : must have "amlogic,meson8-gpio-intc" and either + "amlogic,meson8-gpio-intc" for meson8 SoCs (S802) or + "amlogic,meson8b-gpio-intc" for meson8b SoCs (S805) or + "amlogic,meson-gxbb-gpio-intc" for GXBB SoCs (S905) or + "amlogic,meson-gxl-gpio-intc" for GXL SoCs (S905X, S912) + "amlogic,meson-axg-gpio-intc" for AXG SoCs (A113D, A113X) - interrupt-parent : a phandle to the GIC the interrupts are routed to. Usually this is provided at the root level of the device tree as it is common to most of the SoC. diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt index 0a57f2f4167d..3ea78c4ef887 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt @@ -57,6 +57,20 @@ Optional occupied by the redistributors. Required if more than one such region is present. +- msi-controller: Boolean property. Identifies the node as an MSI + controller. Only present if the Message Based Interrupt + functionnality is being exposed by the HW, and the mbi-ranges + property present. + +- mbi-ranges: A list of pairs <intid span>, where "intid" is the first + SPI of a range that can be used an MBI, and "span" the size of that + range. Multiple ranges can be provided. Requires "msi-controller" to + be set. + +- mbi-alias: Address property. Base address of an alias of the GICD + region containing only the {SET,CLR}SPI registers to be used if + isolation is required, and if supported by the HW. + Sub-nodes: PPI affinity can be expressed as a single "ppi-partitions" node, @@ -99,6 +113,9 @@ Examples: <0x0 0x2c020000 0 0x2000>; // GICV interrupts = <1 9 4>; + msi-controller; + mbi-ranges = <256 128>; + gic-its@2c200000 { compatible = "arm,gic-v3-its"; msi-controller; diff --git a/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt b/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt index edf03f09244b..136bd612bd83 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt @@ -5,11 +5,14 @@ Required properties: - compatible: Should be: "st,stm32-exti" "st,stm32h7-exti" + "st,stm32mp1-exti" - reg: Specifies base physical address and size of the registers - interrupt-controller: Indentifies the node as an interrupt controller - #interrupt-cells: Specifies the number of cells to encode an interrupt specifier, shall be 2 - interrupts: interrupts references to primary interrupt controller + (only needed for exti controller with multiple exti under + same parent interrupt: st,stm32-exti and st,stm32h7-exti") Example: diff --git a/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt b/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt index 1fd5d69647ca..ffadb7c6f1f3 100644 --- a/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt +++ b/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt @@ -11,6 +11,8 @@ Required Properties: the device is compatible with the R-Car Gen2 VMSA-compatible IPMMU. - "renesas,ipmmu-r8a73a4" for the R8A73A4 (R-Mobile APE6) IPMMU. + - "renesas,ipmmu-r8a7743" for the R8A7743 (RZ/G1M) IPMMU. + - "renesas,ipmmu-r8a7745" for the R8A7745 (RZ/G1E) IPMMU. - "renesas,ipmmu-r8a7790" for the R8A7790 (R-Car H2) IPMMU. - "renesas,ipmmu-r8a7791" for the R8A7791 (R-Car M2-W) IPMMU. - "renesas,ipmmu-r8a7793" for the R8A7793 (R-Car M2-N) IPMMU. @@ -19,7 +21,8 @@ Required Properties: - "renesas,ipmmu-r8a7796" for the R8A7796 (R-Car M3-W) IPMMU. - "renesas,ipmmu-r8a77970" for the R8A77970 (R-Car V3M) IPMMU. - "renesas,ipmmu-r8a77995" for the R8A77995 (R-Car D3) IPMMU. - - "renesas,ipmmu-vmsa" for generic R-Car Gen2 VMSA-compatible IPMMU. + - "renesas,ipmmu-vmsa" for generic R-Car Gen2 or RZ/G1 VMSA-compatible + IPMMU. - reg: Base address and size of the IPMMU registers. - interrupts: Specifiers for the MMU fault interrupts. For instances that diff --git a/Documentation/devicetree/bindings/iommu/rockchip,iommu.txt b/Documentation/devicetree/bindings/iommu/rockchip,iommu.txt index 2098f7732264..6ecefea1c6f9 100644 --- a/Documentation/devicetree/bindings/iommu/rockchip,iommu.txt +++ b/Documentation/devicetree/bindings/iommu/rockchip,iommu.txt @@ -14,6 +14,11 @@ Required properties: "single-master" device, and needs no additional information to associate with its master device. See: Documentation/devicetree/bindings/iommu/iommu.txt +- clocks : A list of clocks required for the IOMMU to be accessible by + the host CPU. +- clock-names : Should contain the following: + "iface" - Main peripheral bus clock (PCLK/HCL) (required) + "aclk" - AXI bus clock (required) Optional properties: - rockchip,disable-mmu-reset : Don't use the mmu reset operation. @@ -27,5 +32,7 @@ Example: reg = <0xff940300 0x100>; interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "vopl_mmu"; + clocks = <&cru ACLK_VOP1>, <&cru HCLK_VOP1>; + clock-names = "aclk", "iface"; #iommu-cells = <0>; }; diff --git a/Documentation/devicetree/bindings/ipmi/npcm7xx-kcs-bmc.txt b/Documentation/devicetree/bindings/ipmi/npcm7xx-kcs-bmc.txt new file mode 100644 index 000000000000..3538a214fff1 --- /dev/null +++ b/Documentation/devicetree/bindings/ipmi/npcm7xx-kcs-bmc.txt @@ -0,0 +1,39 @@ +* Nuvoton NPCM7xx KCS (Keyboard Controller Style) IPMI interface + +The Nuvoton SOCs (NPCM7xx) are commonly used as BMCs +(Baseboard Management Controllers) and the KCS interface can be +used to perform in-band IPMI communication with their host. + +Required properties: +- compatible : should be one of + "nuvoton,npcm750-kcs-bmc" +- interrupts : interrupt generated by the controller +- kcs_chan : The KCS channel number in the controller + +Example: + + lpc_kcs: lpc_kcs@f0007000 { + compatible = "nuvoton,npcm750-lpc-kcs", "simple-mfd", "syscon"; + reg = <0xf0007000 0x40>; + reg-io-width = <1>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0xf0007000 0x40>; + + kcs1: kcs1@0 { + compatible = "nuvoton,npcm750-kcs-bmc"; + reg = <0x0 0x40>; + interrupts = <0 9 4>; + kcs_chan = <1>; + status = "disabled"; + }; + + kcs2: kcs2@0 { + compatible = "nuvoton,npcm750-kcs-bmc"; + reg = <0x0 0x40>; + interrupts = <0 9 4>; + kcs_chan = <2>; + status = "disabled"; + }; + };
\ No newline at end of file diff --git a/Documentation/devicetree/bindings/leds/leds-cr0014114.txt b/Documentation/devicetree/bindings/leds/leds-cr0014114.txt new file mode 100644 index 000000000000..4255b19ad25c --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-cr0014114.txt @@ -0,0 +1,54 @@ +Crane Merchandising System - cr0014114 LED driver +------------------------------------------------- + +This LED Board is widely used in vending machines produced +by Crane Merchandising Systems. + +Required properties: +- compatible: "crane,cr0014114" + +Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt +apply. In particular, "reg" and "spi-max-frequency" properties must be given. + +LED sub-node properties: +- label : + see Documentation/devicetree/bindings/leds/common.txt +- linux,default-trigger : (optional) + see Documentation/devicetree/bindings/leds/common.txt + +Example +------- + +led-controller@0 { + compatible = "crane,cr0014114"; + reg = <0>; + spi-max-frequency = <50000>; + #address-cells = <1>; + #size-cells = <0>; + + led@0 { + reg = <0>; + label = "red:coin"; + }; + led@1 { + reg = <1>; + label = "green:coin"; + }; + led@2 { + reg = <2>; + label = "blue:coin"; + }; + led@3 { + reg = <3>; + label = "red:bill"; + }; + led@4 { + reg = <4>; + label = "green:bill"; + }; + led@5 { + reg = <5>; + label = "blue:bill"; + }; + ... +}; diff --git a/Documentation/devicetree/bindings/leds/leds-lm3601x.txt b/Documentation/devicetree/bindings/leds/leds-lm3601x.txt new file mode 100644 index 000000000000..a88b2c41e75b --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-lm3601x.txt @@ -0,0 +1,45 @@ +* Texas Instruments - lm3601x Single-LED Flash Driver + +The LM3601X are ultra-small LED flash drivers that +provide a high level of adjustability. + +Required properties: + - compatible : Can be one of the following + "ti,lm36010" + "ti,lm36011" + - reg : I2C slave address + - #address-cells : 1 + - #size-cells : 0 + +Required child properties: + - reg : 0 - Indicates a IR mode + 1 - Indicates a Torch (white LED) mode + +Required properties for flash LED child nodes: + See Documentation/devicetree/bindings/leds/common.txt + - flash-max-microamp : Range from 11mA - 1.5A + - flash-max-timeout-us : Range from 40ms - 1600ms + - led-max-microamp : Range from 2.4mA - 376mA + +Optional child properties: + - label : see Documentation/devicetree/bindings/leds/common.txt + +Example: +led-controller@64 { + compatible = "ti,lm36010"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x64>; + + led@0 { + reg = <1>; + label = "white:torch"; + led-max-microamp = <376000>; + flash-max-microamp = <1500000>; + flash-max-timeout-us = <1600000>; + }; +} + +For more product information please see the links below: +http://www.ti.com/product/LM36010 +http://www.ti.com/product/LM36011 diff --git a/Documentation/devicetree/bindings/leds/leds-sc27xx-bltc.txt b/Documentation/devicetree/bindings/leds/leds-sc27xx-bltc.txt new file mode 100644 index 000000000000..dddf84f9c7ea --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-sc27xx-bltc.txt @@ -0,0 +1,41 @@ +LEDs connected to Spreadtrum SC27XX PMIC breathing light controller + +The SC27xx breathing light controller supports to 3 outputs: +red LED, green LED and blue LED. Each LED can work at normal +PWM mode or breath light mode. + +Required properties: +- compatible: Should be "sprd,sc2731-bltc". +- #address-cells: Must be 1. +- #size-cells: Must be 0. +- reg: Specify the controller address. + +Required child properties: +- reg: Port this LED is connected to. + +Optional child properties: +- label: See Documentation/devicetree/bindings/leds/common.txt. + +Examples: + +led-controller@200 { + compatible = "sprd,sc2731-bltc"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x200>; + + led@0 { + label = "red"; + reg = <0x0>; + }; + + led@1 { + label = "green"; + reg = <0x1>; + }; + + led@2 { + label = "blue"; + reg = <0x2>; + }; +}; diff --git a/Documentation/devicetree/bindings/mailbox/hisilicon,hi3660-mailbox.txt b/Documentation/devicetree/bindings/mailbox/hisilicon,hi3660-mailbox.txt new file mode 100644 index 000000000000..3e5b4537407d --- /dev/null +++ b/Documentation/devicetree/bindings/mailbox/hisilicon,hi3660-mailbox.txt @@ -0,0 +1,51 @@ +Hisilicon Hi3660 Mailbox Controller + +Hisilicon Hi3660 mailbox controller supports up to 32 channels. Messages +are passed between processors, including application & communication +processors, MCU, HIFI, etc. Each channel is unidirectional and accessed +by using MMIO registers; it supports maximum to 8 words message. + +Controller +---------- + +Required properties: +- compatible: : Shall be "hisilicon,hi3660-mbox" +- reg: : Offset and length of the device's register set +- #mbox-cells: : Must be 3 + <&phandle channel dst_irq ack_irq> + phandle : Label name of controller + channel : Channel number + dst_irq : Remote interrupt vector + ack_irq : Local interrupt vector + +- interrupts: : Contains the two IRQ lines for mailbox. + +Example: + +mailbox: mailbox@e896b000 { + compatible = "hisilicon,hi3660-mbox"; + reg = <0x0 0xe896b000 0x0 0x1000>; + interrupts = <0x0 0xc0 0x4>, + <0x0 0xc1 0x4>; + #mbox-cells = <3>; +}; + +Client +------ + +Required properties: +- compatible : See the client docs +- mboxes : Standard property to specify a Mailbox (See ./mailbox.txt) + Cells must match 'mbox-cells' (See Controller docs above) + +Optional properties +- mbox-names : Name given to channels seen in the 'mboxes' property. + +Example: + +stub_clock: stub_clock@e896b500 { + compatible = "hisilicon,hi3660-stub-clk"; + reg = <0x0 0xe896b500 0x0 0x0100>; + #clock-cells = <1>; + mboxes = <&mailbox 13 3 0>; +}; diff --git a/Documentation/devicetree/bindings/mailbox/mailbox.txt b/Documentation/devicetree/bindings/mailbox/mailbox.txt index be05b9746c69..af8ecee2ac68 100644 --- a/Documentation/devicetree/bindings/mailbox/mailbox.txt +++ b/Documentation/devicetree/bindings/mailbox/mailbox.txt @@ -23,6 +23,11 @@ Required property: Optional property: - mbox-names: List of identifier strings for each mailbox channel. +- shmem : List of phandle pointing to the shared memory(SHM) area between the + users of these mailboxes for IPC, one for each mailbox. This shared + memory can be part of any memory reserved for the purpose of this + communication between the mailbox client and the remote. + Example: pwr_cntrl: power { @@ -30,3 +35,26 @@ Example: mbox-names = "pwr-ctrl", "rpc"; mboxes = <&mailbox 0 &mailbox 1>; }; + +Example with shared memory(shmem): + + sram: sram@50000000 { + compatible = "mmio-sram"; + reg = <0x50000000 0x10000>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x50000000 0x10000>; + + cl_shmem: shmem@0 { + compatible = "client-shmem"; + reg = <0x0 0x200>; + }; + }; + + client@2e000000 { + ... + mboxes = <&mailbox 0>; + shmem = <&cl_shmem>; + .. + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt index 621b41c79faa..44d71469c914 100644 --- a/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt +++ b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt @@ -3,7 +3,9 @@ EMIF - External Memory Interface - is an SDRAM controller used in TI SoCs. EMIF supports, based on the IP revision, one or more of DDR2/DDR3/LPDDR2 protocols. This binding describes a given instance -of the EMIF IP and memory parts attached to it. +of the EMIF IP and memory parts attached to it. Certain revisions +of the EMIF controller also contain optional ECC support, which +corrects one bit errors and detects two bit errors. Required properties: - compatible : Should be of the form "ti,emif-<ip-rev>" where <ip-rev> @@ -11,6 +13,8 @@ Required properties: compatible should be one of the following: "ti,emif-am3352" "ti,emif-am4372" + "ti,emif-dra7xx" + "ti,emif-keystone" - phy-type : <u32> indicating the DDR phy type. Following are the allowed values @@ -22,6 +26,7 @@ Required properties: - ti,hwmods : For TI hwmods processing and omap device creation the value shall be "emif<n>" where <n> is the number of the EMIF instance with base 1. +- interrupts : interrupt used by the controller Required only for "ti,emif-am3352" and "ti,emif-am4372": - sram : Phandles for generic sram driver nodes, @@ -71,3 +76,9 @@ emif: emif@4c000000 { sram = <&pm_sram_code &pm_sram_data>; }; + +emif1: emif@4c000000 { + compatible = "ti,emif-dra7xx"; + reg = <0x4c000000 0x200>; + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt b/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt index 69aadee00d5f..34dd89087cff 100644 --- a/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt +++ b/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt @@ -176,3 +176,24 @@ lhc: lhc@20 { compatible = "aspeed,ast2500-lhc"; reg = <0x20 0x24 0x48 0x8>; }; + +LPC reset control +----------------- + +The UARTs present in the ASPEED SoC can have their resets tied to the reset +state of the LPC bus. Some systems may chose to modify this configuration. + +Required properties: + + - compatible: "aspeed,ast2500-lpc-reset" or + "aspeed,ast2400-lpc-reset" + - reg: offset and length of the IP in the LHC memory region + - #reset-controller indicates the number of reset cells expected + +Example: + +lpc_reset: reset-controller@18 { + compatible = "aspeed,ast2500-lpc-reset"; + reg = <0x18 0x4>; + #reset-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/mips/mscc.txt b/Documentation/devicetree/bindings/mips/mscc.txt new file mode 100644 index 000000000000..ae15ec333542 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/mscc.txt @@ -0,0 +1,43 @@ +* Microsemi MIPS CPUs + +Boards with a SoC of the Microsemi MIPS family shall have the following +properties: + +Required properties: +- compatible: "mscc,ocelot" + + +* Other peripherals: + +o CPU chip regs: + +The SoC has a few registers (DEVCPU_GCB:CHIP_REGS) handling miscellaneous +functionalities: chip ID, general purpose register for software use, reset +controller, hardware status and configuration, efuses. + +Required properties: +- compatible: Should be "mscc,ocelot-chip-regs", "simple-mfd", "syscon" +- reg : Should contain registers location and length + +Example: + syscon@71070000 { + compatible = "mscc,ocelot-chip-regs", "simple-mfd", "syscon"; + reg = <0x71070000 0x1c>; + }; + + +o CPU system control: + +The SoC has a few registers (ICPU_CFG:CPU_SYSTEM_CTRL) handling configuration of +the CPU: 8 general purpose registers, reset control, CPU en/disabling, CPU +endianness, CPU bus control, CPU status. + +Required properties: +- compatible: Should be "mscc,ocelot-cpu-syscon", "syscon" +- reg : Should contain registers location and length + +Example: + syscon@70000000 { + compatible = "mscc,ocelot-cpu-syscon", "syscon"; + reg = <0x70000000 0x2c>; + }; diff --git a/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt index 50bf611a4d2c..13e70409e8ac 100644 --- a/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt +++ b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt @@ -12,6 +12,7 @@ Required properties: - "amlogic,meson-gxbb-mmc" - "amlogic,meson-gxl-mmc" - "amlogic,meson-gxm-mmc" + - "amlogic,meson-axg-mmc" - clocks : A list of phandle + clock-specifier pairs for the clocks listed in clock-names. - clock-names: Should contain the following: "core" - Main peripheral bus clock @@ -19,6 +20,7 @@ Required properties: "clkin1" - Other parent clock of internal mux The driver has an internal mux clock which switches between clkin0 and clkin1 depending on the clock rate requested by the MMC core. +- resets : phandle of the internal reset line Example: @@ -29,4 +31,5 @@ Example: clocks = <&clkc CLKID_SD_EMMC_A>, <&xtal>, <&clkc CLKID_FCLK_DIV2>; clock-names = "core", "clkin0", "clkin1"; pinctrl-0 = <&emmc_pins>; + resets = <&reset RESET_SD_EMMC_A>; }; diff --git a/Documentation/devicetree/bindings/mmc/bluefield-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/bluefield-dw-mshc.txt new file mode 100644 index 000000000000..b0f0999ea1a9 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/bluefield-dw-mshc.txt @@ -0,0 +1,29 @@ +* Mellanox Bluefield SoC specific extensions to the Synopsys Designware + Mobile Storage Host Controller + +Read synopsys-dw-mshc.txt for more details + +The Synopsys designware mobile storage host controller is used to interface +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents +differences between the core Synopsys dw mshc controller properties described +by synopsys-dw-mshc.txt and the properties used by the Mellanox Bluefield SoC +specific extensions to the Synopsys Designware Mobile Storage Host Controller. + +Required Properties: + +* compatible: should be one of the following. + - "mellanox,bluefield-dw-mshc": for controllers with Mellanox Bluefield SoC + specific extensions. + +Example: + + /* Mellanox Bluefield SoC MMC */ + mmc@6008000 { + compatible = "mellanox,bluefield-dw-mshc"; + reg = <0x6008000 0x400>; + interrupts = <32>; + fifo-depth = <0x100>; + clock-frequency = <24000000>; + bus-width = <8>; + cap-mmc-highspeed; + }; diff --git a/Documentation/devicetree/bindings/mmc/jz4740.txt b/Documentation/devicetree/bindings/mmc/jz4740.txt new file mode 100644 index 000000000000..7cd8c432d7c8 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/jz4740.txt @@ -0,0 +1,38 @@ +* Ingenic JZ47xx MMC controllers + +This file documents the device tree properties used for the MMC controller in +Ingenic JZ4740/JZ4780 SoCs. These are in addition to the core MMC properties +described in mmc.txt. + +Required properties: +- compatible: Should be one of the following: + - "ingenic,jz4740-mmc" for the JZ4740 + - "ingenic,jz4780-mmc" for the JZ4780 +- reg: Should contain the MMC controller registers location and length. +- interrupts: Should contain the interrupt specifier of the MMC controller. +- clocks: Clock for the MMC controller. + +Optional properties: +- dmas: List of DMA specifiers with the controller specific format + as described in the generic DMA client binding. A tx and rx + specifier is required. +- dma-names: RX and TX DMA request names. + Should be "rx" and "tx", in that order. + +For additional details on DMA client bindings see ../dma/dma.txt. + +Example: + +mmc0: mmc@13450000 { + compatible = "ingenic,jz4780-mmc"; + reg = <0x13450000 0x1000>; + + interrupt-parent = <&intc>; + interrupts = <37>; + + clocks = <&cgu JZ4780_CLK_MSC0>; + clock-names = "mmc"; + + dmas = <&dma JZ4780_DMA_MSC0_RX 0xffffffff>, <&dma JZ4780_DMA_MSC0_TX 0xffffffff>; + dma-names = "rx", "tx"; +}; diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 467cd7b147ce..f5a0923b34ca 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -19,6 +19,8 @@ Optional properties: - wp-gpios: Specify GPIOs for write protection, see gpio binding - cd-inverted: when present, polarity on the CD line is inverted. See the note below for the case, when a GPIO is used for the CD line +- cd-debounce-delay-ms: Set delay time before detecting card after card insert interrupt. + It's only valid when cd-gpios is present. - wp-inverted: when present, polarity on the WP line is inverted. See the note below for the case, when a GPIO is used for the WP line - disable-wp: When set no physical WP line is present. This property should @@ -56,6 +58,10 @@ Optional properties: - fixed-emmc-driver-type: for non-removable eMMC, enforce this driver type. The value <n> is the driver type as specified in the eMMC specification (table 206 in spec version 5.1). +- post-power-on-delay-ms : It was invented for MMC pwrseq-simple which could + be referred to mmc-pwrseq-simple.txt. But now it's reused as a tunable delay + waiting for I/O signalling and card power supply to be stable, regardless of + whether pwrseq-simple is used. Default to 10ms if no available. *NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line polarity properties, we have to fix the meaning of the "normal" and "inverted" diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt index c6558785e61b..8ce49b255974 100644 --- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt @@ -21,7 +21,7 @@ Required Properties: - "rockchip,rk3399-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3399 Optional Properties: -* clocks: from common clock binding: if ciu_drive and ciu_sample are +* clocks: from common clock binding: if ciu-drive and ciu-sample are specified in clock-names, should contain handles to these clocks. * clock-names: Apart from the clock-names described in synopsys-dw-mshc.txt @@ -29,7 +29,7 @@ Optional Properties: to control the clock phases, "ciu-sample" is required for tuning high- speed modes. -* rockchip,default-sample-phase: The default phase to set ciu_sample at +* rockchip,default-sample-phase: The default phase to set ciu-sample at probing, low speeds or in case where all phases work at tuning time. If not specified 0 deg will be used. diff --git a/Documentation/devicetree/bindings/mmc/sdhci-omap.txt b/Documentation/devicetree/bindings/mmc/sdhci-omap.txt index 51775a372c06..393848c2138e 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-omap.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-omap.txt @@ -4,7 +4,14 @@ Refer to mmc.txt for standard MMC bindings. Required properties: - compatible: Should be "ti,dra7-sdhci" for DRA7 and DRA72 controllers + Should be "ti,k2g-sdhci" for K2G - ti,hwmods: Must be "mmc<n>", <n> is controller instance starting 1 + (Not required for K2G). +- pinctrl-names: Should be subset of "default", "hs", "sdr12", "sdr25", "sdr50", + "ddr50-rev11", "sdr104-rev11", "ddr50", "sdr104", + "ddr_1_8v-rev11", "ddr_1_8v" or "ddr_3_3v", "hs200_1_8v-rev11", + "hs200_1_8v", +- pinctrl-<n> : Pinctrl states as described in bindings/pinctrl/pinctrl-bindings.txt Example: mmc1: mmc@4809c000 { diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index 2d5287eeed95..ee978c95189d 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -26,6 +26,8 @@ Required properties: "renesas,sdhi-r8a7794" - SDHI IP on R8A7794 SoC "renesas,sdhi-r8a7795" - SDHI IP on R8A7795 SoC "renesas,sdhi-r8a7796" - SDHI IP on R8A7796 SoC + "renesas,sdhi-r8a77965" - SDHI IP on R8A77965 SoC + "renesas,sdhi-r8a77980" - SDHI IP on R8A77980 SoC "renesas,sdhi-r8a77995" - SDHI IP on R8A77995 SoC "renesas,sdhi-shmobile" - a generic sh-mobile SDHI controller "renesas,rcar-gen1-sdhi" - a generic R-Car Gen1 SDHI controller diff --git a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt index 63d4d626fbd5..483e9cfac1b1 100644 --- a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt +++ b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt @@ -39,3 +39,27 @@ qspi0: quadspi@40044000 { .... }; }; + +Example showing the usage of two SPI NOR devices: + +&qspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_qspi2>; + status = "okay"; + + flash0: n25q256a@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "micron,n25q256a", "jedec,spi-nor"; + spi-max-frequency = <29000000>; + reg = <0>; + }; + + flash1: n25q256a@1 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "micron,n25q256a", "jedec,spi-nor"; + spi-max-frequency = <29000000>; + reg = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/marvell-nand.txt b/Documentation/devicetree/bindings/mtd/marvell-nand.txt index c08fb477b3c6..e0c790706b9b 100644 --- a/Documentation/devicetree/bindings/mtd/marvell-nand.txt +++ b/Documentation/devicetree/bindings/mtd/marvell-nand.txt @@ -14,7 +14,10 @@ Required properties: - #address-cells: shall be set to 1. Encode the NAND CS. - #size-cells: shall be set to 0. - interrupts: shall define the NAND controller interrupt. -- clocks: shall reference the NAND controller clock. +- clocks: shall reference the NAND controller clocks, the second one is + is only needed for the Armada 7K/8K SoCs +- clock-names: mandatory if there is a second clock, in this case there + should be one clock named "core" and another one named "reg" - marvell,system-controller: Set to retrieve the syscon node that handles NAND controller related registers (only required with the "marvell,armada-8k-nand[-controller]" compatibles). diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt index 4a0a48bf4ecb..232fa12e90ef 100644 --- a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt +++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt @@ -41,6 +41,13 @@ additional (optional) property is defined: - erase-size : The chip's physical erase block size in bytes. + The device tree may optionally contain endianness property. + little-endian or big-endian : It Represents the endianness that should be used + by the controller to properly read/write data + from/to the flash. If this property is missing, + the endianness is chosen by the system + (potentially based on extra configuration options). + The device tree may optionally contain sub-nodes describing partitions of the address space. See partition.txt for more detail. diff --git a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt deleted file mode 100644 index d4ee4da58463..000000000000 --- a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt +++ /dev/null @@ -1,50 +0,0 @@ -PXA3xx NAND DT bindings - -Required properties: - - - compatible: Should be set to one of the following: - marvell,pxa3xx-nand - marvell,armada370-nand - marvell,armada-8k-nand - - reg: The register base for the controller - - interrupts: The interrupt to map - - #address-cells: Set to <1> if the node includes partitions - - marvell,system-controller: Set to retrieve the syscon node that handles - NAND controller related registers (only required - with marvell,armada-8k-nand compatible). - -Optional properties: - - - dmas: dma data channel, see dma.txt binding doc - - marvell,nand-enable-arbiter: Set to enable the bus arbiter - - marvell,nand-keep-config: Set to keep the NAND controller config as set - by the bootloader - - num-cs: Number of chipselect lines to use - - nand-on-flash-bbt: boolean to enable on flash bbt option if - not present false - - nand-ecc-strength: number of bits to correct per ECC step - - nand-ecc-step-size: number of data bytes covered by a single ECC step - -The following ECC strength and step size are currently supported: - - - nand-ecc-strength = <1>, nand-ecc-step-size = <512> - - nand-ecc-strength = <4>, nand-ecc-step-size = <512> - - nand-ecc-strength = <8>, nand-ecc-step-size = <512> - -Example: - - nand0: nand@43100000 { - compatible = "marvell,pxa3xx-nand"; - reg = <0x43100000 90>; - interrupts = <45>; - dmas = <&pdma 97 0>; - dma-names = "data"; - #address-cells = <1>; - - marvell,nand-enable-arbiter; - marvell,nand-keep-config; - num-cs = <1>; - - /* partitions (optional) */ - }; - diff --git a/Documentation/devicetree/bindings/mtd/sunxi-nand.txt b/Documentation/devicetree/bindings/mtd/sunxi-nand.txt index 5e13a5cdff03..0734f03bf3d3 100644 --- a/Documentation/devicetree/bindings/mtd/sunxi-nand.txt +++ b/Documentation/devicetree/bindings/mtd/sunxi-nand.txt @@ -24,8 +24,8 @@ Optional properties: - allwinner,rb : shall contain the native Ready/Busy ids. or - rb-gpios : shall contain the gpios used as R/B pins. -- nand-ecc-mode : one of the supported ECC modes ("hw", "hw_syndrome", "soft", - "soft_bch" or "none") +- nand-ecc-mode : one of the supported ECC modes ("hw", "soft", "soft_bch" or + "none") see Documentation/devicetree/bindings/mtd/nand.txt for generic bindings. diff --git a/Documentation/devicetree/bindings/net/can/rcar_canfd.txt b/Documentation/devicetree/bindings/net/can/rcar_canfd.txt index 93c3a6ae32f9..ac71daa46195 100644 --- a/Documentation/devicetree/bindings/net/can/rcar_canfd.txt +++ b/Documentation/devicetree/bindings/net/can/rcar_canfd.txt @@ -5,7 +5,9 @@ Required properties: - compatible: Must contain one or more of the following: - "renesas,rcar-gen3-canfd" for R-Car Gen3 compatible controller. - "renesas,r8a7795-canfd" for R8A7795 (R-Car H3) compatible controller. - - "renesas,r8a7796-canfd" for R8A7796 (R-Car M3) compatible controller. + - "renesas,r8a7796-canfd" for R8A7796 (R-Car M3-W) compatible controller. + - "renesas,r8a77970-canfd" for R8A77970 (R-Car V3M) compatible controller. + - "renesas,r8a77980-canfd" for R8A77980 (R-Car V3H) compatible controller. When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first, followed by the diff --git a/Documentation/devicetree/bindings/net/dsa/b53.txt b/Documentation/devicetree/bindings/net/dsa/b53.txt index 8acf51a4dfa8..47a6a7fe0b86 100644 --- a/Documentation/devicetree/bindings/net/dsa/b53.txt +++ b/Documentation/devicetree/bindings/net/dsa/b53.txt @@ -10,6 +10,7 @@ Required properties: "brcm,bcm53128" "brcm,bcm5365" "brcm,bcm5395" + "brcm,bcm5389" "brcm,bcm5397" "brcm,bcm5398" diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt index 594982c6b9f9..79bf352e659c 100644 --- a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt +++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt @@ -6,7 +6,11 @@ the definition of the PHY node in booting-without-of.txt for an example of how to define a PHY. Required properties: - - reg : Offset and length of the register set for the device + - reg : Offset and length of the register set for the device, and optionally + the offset and length of the TBIPA register (TBI PHY address + register). If TBIPA register is not specified, the driver will + attempt to infer it from the register set specified (your mileage may + vary). - compatible : Should define the compatible device type for the mdio. Currently supported strings/devices are: - "fsl,gianfar-tbi" diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt index 1814fa13f6ab..fc019df0d863 100644 --- a/Documentation/devicetree/bindings/net/marvell-pp2.txt +++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt @@ -21,9 +21,10 @@ Required properties: - main controller clock (for both armada-375-pp2 and armada-7k-pp2) - GOP clock (for both armada-375-pp2 and armada-7k-pp2) - MG clock (only for armada-7k-pp2) + - MG Core clock (only for armada-7k-pp2) - AXI clock (only for armada-7k-pp2) -- clock-names: names of used clocks, must be "pp_clk", "gop_clk", "mg_clk" - and "axi_clk" (the 2 latter only for armada-7k-pp2). +- clock-names: names of used clocks, must be "pp_clk", "gop_clk", "mg_clk", + "mg_core_clk" and "axi_clk" (the 3 latter only for armada-7k-pp2). The ethernet ports are represented by subnodes. At least one port is required. @@ -80,8 +81,8 @@ cpm_ethernet: ethernet@0 { compatible = "marvell,armada-7k-pp22"; reg = <0x0 0x100000>, <0x129000 0xb000>; clocks = <&cpm_syscon0 1 3>, <&cpm_syscon0 1 9>, - <&cpm_syscon0 1 5>, <&cpm_syscon0 1 18>; - clock-names = "pp_clk", "gop_clk", "gp_clk", "axi_clk"; + <&cpm_syscon0 1 5>, <&cpm_syscon0 1 6>, <&cpm_syscon0 1 18>; + clock-names = "pp_clk", "gop_clk", "mg_clk", "mg_core_clk", "axi_clk"; eth0: eth0 { interrupts = <ICU_GRP_NSR 39 IRQ_TYPE_LEVEL_HIGH>, diff --git a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt index 42a248301615..e22d8cfea687 100644 --- a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt +++ b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt @@ -57,6 +57,13 @@ KSZ9031: - txd2-skew-ps : Skew control of TX data 2 pad - txd3-skew-ps : Skew control of TX data 3 pad + - micrel,force-master: + Boolean, force phy to master mode. Only set this option if the phy + reference clock provided at CLK125_NDO pin is used as MAC reference + clock because the clock jitter in slave mode is to high (errata#2). + Attention: The link partner must be configurable as slave otherwise + no link will be established. + Examples: mdio { diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt index c306f55d335b..890526dbfc26 100644 --- a/Documentation/devicetree/bindings/net/renesas,ravb.txt +++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt @@ -18,6 +18,7 @@ Required properties: - "renesas,etheravb-r8a7795" for the R8A7795 SoC. - "renesas,etheravb-r8a7796" for the R8A7796 SoC. + - "renesas,etheravb-r8a77965" for the R8A77965 SoC. - "renesas,etheravb-r8a77970" for the R8A77970 SoC. - "renesas,etheravb-r8a77980" for the R8A77980 SoC. - "renesas,etheravb-r8a77995" for the R8A77995 SoC. diff --git a/Documentation/devicetree/bindings/nvmem/zii,rave-sp-eeprom.txt b/Documentation/devicetree/bindings/nvmem/zii,rave-sp-eeprom.txt new file mode 100644 index 000000000000..d5e22fc67d66 --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/zii,rave-sp-eeprom.txt @@ -0,0 +1,40 @@ +Zodiac Inflight Innovations RAVE EEPROM Bindings + +RAVE SP EEPROM device is a "MFD cell" device exposing physical EEPROM +attached to RAVE Supervisory Processor. It is expected that its Device +Tree node is specified as a child of the node corresponding to the +parent RAVE SP device (as documented in +Documentation/devicetree/bindings/mfd/zii,rave-sp.txt) + +Required properties: + +- compatible: Should be "zii,rave-sp-eeprom" + +Optional properties: + +- zii,eeprom-name: Unique EEPROM identifier describing its function in the + system. Will be used as created NVMEM deivce's name. + +Data cells: + +Data cells are child nodes of eerpom node, bindings for which are +documented in Documentation/bindings/nvmem/nvmem.txt + +Example: + + rave-sp { + compatible = "zii,rave-sp-rdu1"; + current-speed = <38400>; + + eeprom@a4 { + compatible = "zii,rave-sp-eeprom"; + reg = <0xa4 0x4000>; + #address-cells = <1>; + #size-cells = <1>; + zii,eeprom-name = "main-eeprom"; + + wdt_timeout: wdt-timeout@81 { + reg = <0x81 2>; + }; + }; + } diff --git a/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt b/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt new file mode 100644 index 000000000000..c2127b96805a --- /dev/null +++ b/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt @@ -0,0 +1,680 @@ +Qualcomm Technologies, Inc. KRYO CPUFreq and OPP bindings +=================================== + +In Certain Qualcomm Technologies, Inc. SoCs like apq8096 and msm8996 +that have KRYO processors, the CPU ferequencies subset and voltage value +of each OPP varies based on the silicon variant in use. +Qualcomm Technologies, Inc. Process Voltage Scaling Tables +defines the voltage and frequency value based on the msm-id in SMEM +and speedbin blown in the efuse combination. +The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC +to provide the OPP framework with required information (existing HW bitmap). +This is used to determine the voltage and frequency value for each OPP of +operating-points-v2 table when it is parsed by the OPP framework. + +Required properties: +-------------------- +In 'cpus' nodes: +- operating-points-v2: Phandle to the operating-points-v2 table to use. + +In 'operating-points-v2' table: +- compatible: Should be + - 'operating-points-v2-kryo-cpu' for apq8096 and msm8996. +- nvmem-cells: A phandle pointing to a nvmem-cells node representing the + efuse registers that has information about the + speedbin that is used to select the right frequency/voltage + value pair. + Please refer the for nvmem-cells + bindings Documentation/devicetree/bindings/nvmem/nvmem.txt + and also examples below. + +In every OPP node: +- opp-supported-hw: A single 32 bit bitmap value, representing compatible HW. + Bitmap: + 0: MSM8996 V3, speedbin 0 + 1: MSM8996 V3, speedbin 1 + 2: MSM8996 V3, speedbin 2 + 3: unused + 4: MSM8996 SG, speedbin 0 + 5: MSM8996 SG, speedbin 1 + 6: MSM8996 SG, speedbin 2 + 7-31: unused + +Example 1: +--------- + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "qcom,kryo"; + reg = <0x0 0x0>; + enable-method = "psci"; + clocks = <&kryocc 0>; + cpu-supply = <&pm8994_s11_saw>; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + next-level-cache = <&L2_0>; + L2_0: l2-cache { + compatible = "cache"; + cache-level = <2>; + }; + }; + + CPU1: cpu@1 { + device_type = "cpu"; + compatible = "qcom,kryo"; + reg = <0x0 0x1>; + enable-method = "psci"; + clocks = <&kryocc 0>; + cpu-supply = <&pm8994_s11_saw>; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + next-level-cache = <&L2_0>; + }; + + CPU2: cpu@100 { + device_type = "cpu"; + compatible = "qcom,kryo"; + reg = <0x0 0x100>; + enable-method = "psci"; + clocks = <&kryocc 1>; + cpu-supply = <&pm8994_s11_saw>; + operating-points-v2 = <&cluster1_opp>; + #cooling-cells = <2>; + next-level-cache = <&L2_1>; + L2_1: l2-cache { + compatible = "cache"; + cache-level = <2>; + }; + }; + + CPU3: cpu@101 { + device_type = "cpu"; + compatible = "qcom,kryo"; + reg = <0x0 0x101>; + enable-method = "psci"; + clocks = <&kryocc 1>; + cpu-supply = <&pm8994_s11_saw>; + operating-points-v2 = <&cluster1_opp>; + #cooling-cells = <2>; + next-level-cache = <&L2_1>; + }; + + cpu-map { + cluster0 { + core0 { + cpu = <&CPU0>; + }; + + core1 { + cpu = <&CPU1>; + }; + }; + + cluster1 { + core0 { + cpu = <&CPU2>; + }; + + core1 { + cpu = <&CPU3>; + }; + }; + }; + }; + + cluster0_opp: opp_table0 { + compatible = "operating-points-v2-kryo-cpu"; + nvmem-cells = <&speedbin_efuse>; + opp-shared; + + opp-307200000 { + opp-hz = /bits/ 64 <307200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x77>; + clock-latency-ns = <200000>; + }; + opp-384000000 { + opp-hz = /bits/ 64 <384000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-422400000 { + opp-hz = /bits/ 64 <422400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-460800000 { + opp-hz = /bits/ 64 <460800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-480000000 { + opp-hz = /bits/ 64 <480000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-537600000 { + opp-hz = /bits/ 64 <537600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-556800000 { + opp-hz = /bits/ 64 <556800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-614400000 { + opp-hz = /bits/ 64 <614400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-652800000 { + opp-hz = /bits/ 64 <652800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-691200000 { + opp-hz = /bits/ 64 <691200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-729600000 { + opp-hz = /bits/ 64 <729600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-768000000 { + opp-hz = /bits/ 64 <768000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-844800000 { + opp-hz = /bits/ 64 <844800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x77>; + clock-latency-ns = <200000>; + }; + opp-902400000 { + opp-hz = /bits/ 64 <902400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-960000000 { + opp-hz = /bits/ 64 <960000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-979200000 { + opp-hz = /bits/ 64 <979200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1036800000 { + opp-hz = /bits/ 64 <1036800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1056000000 { + opp-hz = /bits/ 64 <1056000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1113600000 { + opp-hz = /bits/ 64 <1113600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1132800000 { + opp-hz = /bits/ 64 <1132800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1190400000 { + opp-hz = /bits/ 64 <1190400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1209600000 { + opp-hz = /bits/ 64 <1209600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1228800000 { + opp-hz = /bits/ 64 <1228800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1286400000 { + opp-hz = /bits/ 64 <1286400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1324800000 { + opp-hz = /bits/ 64 <1324800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x5>; + clock-latency-ns = <200000>; + }; + opp-1363200000 { + opp-hz = /bits/ 64 <1363200000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x72>; + clock-latency-ns = <200000>; + }; + opp-1401600000 { + opp-hz = /bits/ 64 <1401600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x5>; + clock-latency-ns = <200000>; + }; + opp-1440000000 { + opp-hz = /bits/ 64 <1440000000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1478400000 { + opp-hz = /bits/ 64 <1478400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <200000>; + }; + opp-1497600000 { + opp-hz = /bits/ 64 <1497600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x4>; + clock-latency-ns = <200000>; + }; + opp-1516800000 { + opp-hz = /bits/ 64 <1516800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1593600000 { + opp-hz = /bits/ 64 <1593600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x71>; + clock-latency-ns = <200000>; + }; + opp-1996800000 { + opp-hz = /bits/ 64 <1996800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x20>; + clock-latency-ns = <200000>; + }; + opp-2188800000 { + opp-hz = /bits/ 64 <2188800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x10>; + clock-latency-ns = <200000>; + }; + }; + + cluster1_opp: opp_table1 { + compatible = "operating-points-v2-kryo-cpu"; + nvmem-cells = <&speedbin_efuse>; + opp-shared; + + opp-307200000 { + opp-hz = /bits/ 64 <307200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x77>; + clock-latency-ns = <200000>; + }; + opp-384000000 { + opp-hz = /bits/ 64 <384000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-403200000 { + opp-hz = /bits/ 64 <403200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-460800000 { + opp-hz = /bits/ 64 <460800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-480000000 { + opp-hz = /bits/ 64 <480000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-537600000 { + opp-hz = /bits/ 64 <537600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-556800000 { + opp-hz = /bits/ 64 <556800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-614400000 { + opp-hz = /bits/ 64 <614400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-652800000 { + opp-hz = /bits/ 64 <652800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-691200000 { + opp-hz = /bits/ 64 <691200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-729600000 { + opp-hz = /bits/ 64 <729600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-748800000 { + opp-hz = /bits/ 64 <748800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-806400000 { + opp-hz = /bits/ 64 <806400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-825600000 { + opp-hz = /bits/ 64 <825600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-883200000 { + opp-hz = /bits/ 64 <883200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-902400000 { + opp-hz = /bits/ 64 <902400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-940800000 { + opp-hz = /bits/ 64 <940800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-979200000 { + opp-hz = /bits/ 64 <979200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1036800000 { + opp-hz = /bits/ 64 <1036800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1056000000 { + opp-hz = /bits/ 64 <1056000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1113600000 { + opp-hz = /bits/ 64 <1113600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1132800000 { + opp-hz = /bits/ 64 <1132800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1190400000 { + opp-hz = /bits/ 64 <1190400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1209600000 { + opp-hz = /bits/ 64 <1209600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1248000000 { + opp-hz = /bits/ 64 <1248000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1286400000 { + opp-hz = /bits/ 64 <1286400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1324800000 { + opp-hz = /bits/ 64 <1324800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1363200000 { + opp-hz = /bits/ 64 <1363200000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1401600000 { + opp-hz = /bits/ 64 <1401600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1440000000 { + opp-hz = /bits/ 64 <1440000000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1478400000 { + opp-hz = /bits/ 64 <1478400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1516800000 { + opp-hz = /bits/ 64 <1516800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1555200000 { + opp-hz = /bits/ 64 <1555200000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1593600000 { + opp-hz = /bits/ 64 <1593600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1632000000 { + opp-hz = /bits/ 64 <1632000000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1670400000 { + opp-hz = /bits/ 64 <1670400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1708800000 { + opp-hz = /bits/ 64 <1708800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1747200000 { + opp-hz = /bits/ 64 <1747200000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1785600000 { + opp-hz = /bits/ 64 <1785600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1804800000 { + opp-hz = /bits/ 64 <1804800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x6>; + clock-latency-ns = <200000>; + }; + opp-1824000000 { + opp-hz = /bits/ 64 <1824000000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x71>; + clock-latency-ns = <200000>; + }; + opp-1900800000 { + opp-hz = /bits/ 64 <1900800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x74>; + clock-latency-ns = <200000>; + }; + opp-1920000000 { + opp-hz = /bits/ 64 <1920000000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <200000>; + }; + opp-1977600000 { + opp-hz = /bits/ 64 <1977600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x30>; + clock-latency-ns = <200000>; + }; + opp-1996800000 { + opp-hz = /bits/ 64 <1996800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <200000>; + }; + opp-2054400000 { + opp-hz = /bits/ 64 <2054400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x30>; + clock-latency-ns = <200000>; + }; + opp-2073600000 { + opp-hz = /bits/ 64 <2073600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <200000>; + }; + opp-2150400000 { + opp-hz = /bits/ 64 <2150400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x31>; + clock-latency-ns = <200000>; + }; + opp-2246400000 { + opp-hz = /bits/ 64 <2246400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x10>; + clock-latency-ns = <200000>; + }; + opp-2342400000 { + opp-hz = /bits/ 64 <2342400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x10>; + clock-latency-ns = <200000>; + }; + }; + +.... + +reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; +.... + smem_mem: smem-mem@86000000 { + reg = <0x0 0x86000000 0x0 0x200000>; + no-map; + }; +.... +}; + +smem { + compatible = "qcom,smem"; + memory-region = <&smem_mem>; + hwlocks = <&tcsr_mutex 3>; +}; + +soc { +.... + qfprom: qfprom@74000 { + compatible = "qcom,qfprom"; + reg = <0x00074000 0x8ff>; + #address-cells = <1>; + #size-cells = <1>; + .... + speedbin_efuse: speedbin@133 { + reg = <0x133 0x1>; + bits = <5 3>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/opp/opp.txt b/Documentation/devicetree/bindings/opp/opp.txt index 4e4f30288c8b..c396c4c0af92 100644 --- a/Documentation/devicetree/bindings/opp/opp.txt +++ b/Documentation/devicetree/bindings/opp/opp.txt @@ -82,7 +82,10 @@ This defines voltage-current-frequency combinations along with other related properties. Required properties: -- opp-hz: Frequency in Hz, expressed as a 64-bit big-endian integer. +- opp-hz: Frequency in Hz, expressed as a 64-bit big-endian integer. This is a + required property for all device nodes but devices like power domains. The + power domain nodes must have another (implementation dependent) property which + uniquely identifies the OPP nodes. Optional properties: - opp-microvolt: voltage in micro Volts. @@ -159,7 +162,7 @@ Optional properties: - status: Marks the node enabled/disabled. -- required-opp: This contains phandle to an OPP node in another device's OPP +- required-opps: This contains phandle to an OPP node in another device's OPP table. It may contain an array of phandles, where each phandle points to an OPP of a different device. It should not contain multiple phandles to the OPP nodes in the same OPP table. This specifies the minimum required OPP of the diff --git a/Documentation/devicetree/bindings/pci/hisilicon-histb-pcie.txt b/Documentation/devicetree/bindings/pci/hisilicon-histb-pcie.txt index c84bc027930b..760b4d740616 100644 --- a/Documentation/devicetree/bindings/pci/hisilicon-histb-pcie.txt +++ b/Documentation/devicetree/bindings/pci/hisilicon-histb-pcie.txt @@ -34,6 +34,7 @@ Required properties Optional properties: - reset-gpios: The gpio to generate PCIe PERST# assert and deassert signal. +- vpcie-supply: The regulator in charge of PCIe port power. - phys: List of phandle and phy mode specifier, should be 0. - phy-names: Must be "phy". diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt index 3a6ce55dd310..20227a875ac8 100644 --- a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt +++ b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt @@ -78,7 +78,7 @@ Examples for MT7623: #reset-cells = <1>; }; - pcie: pcie-controller@1a140000 { + pcie: pcie@1a140000 { compatible = "mediatek,mt7623-pcie"; device_type = "pci"; reg = <0 0x1a140000 0 0x1000>, /* PCIe shared registers */ @@ -111,7 +111,6 @@ Examples for MT7623: 0x83000000 0 0x60000000 0 0x60000000 0 0x10000000>; /* memory space */ pcie@0,0 { - device_type = "pci"; reg = <0x0000 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; @@ -123,7 +122,6 @@ Examples for MT7623: }; pcie@1,0 { - device_type = "pci"; reg = <0x0800 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; @@ -135,7 +133,6 @@ Examples for MT7623: }; pcie@2,0 { - device_type = "pci"; reg = <0x1000 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; @@ -148,6 +145,7 @@ Examples for MT7623: }; Examples for MT2712: + pcie: pcie@11700000 { compatible = "mediatek,mt2712-pcie"; device_type = "pci"; @@ -169,7 +167,6 @@ Examples for MT2712: ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>; pcie0: pcie@0,0 { - device_type = "pci"; reg = <0x0000 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; @@ -189,7 +186,6 @@ Examples for MT2712: }; pcie1: pcie@1,0 { - device_type = "pci"; reg = <0x0800 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; @@ -210,6 +206,7 @@ Examples for MT2712: }; Examples for MT7622: + pcie: pcie@1a140000 { compatible = "mediatek,mt7622-pcie"; device_type = "pci"; @@ -243,7 +240,6 @@ Examples for MT7622: ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>; pcie0: pcie@0,0 { - device_type = "pci"; reg = <0x0000 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; @@ -263,7 +259,6 @@ Examples for MT7622: }; pcie1: pcie@1,0 { - device_type = "pci"; reg = <0x0800 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt index 3c9d321b3d3b..1fd703bd73e0 100644 --- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt @@ -189,6 +189,10 @@ Value type: <phandle> Definition: A phandle to the analog power supply for IC which generates reference clock +- vddpe-3v3-supply: + Usage: optional + Value type: <phandle> + Definition: A phandle to the PCIe endpoint power supply - phys: Usage: required for apq8084 diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt index 76ba3a61d1a3..1fb614e615da 100644 --- a/Documentation/devicetree/bindings/pci/rcar-pci.txt +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -1,13 +1,15 @@ * Renesas R-Car PCIe interface Required properties: -compatible: "renesas,pcie-r8a7779" for the R8A7779 SoC; +compatible: "renesas,pcie-r8a7743" for the R8A7743 SoC; + "renesas,pcie-r8a7779" for the R8A7779 SoC; "renesas,pcie-r8a7790" for the R8A7790 SoC; "renesas,pcie-r8a7791" for the R8A7791 SoC; "renesas,pcie-r8a7793" for the R8A7793 SoC; "renesas,pcie-r8a7795" for the R8A7795 SoC; "renesas,pcie-r8a7796" for the R8A7796 SoC; - "renesas,pcie-rcar-gen2" for a generic R-Car Gen2 compatible device. + "renesas,pcie-rcar-gen2" for a generic R-Car Gen2 or + RZ/G1 compatible device. "renesas,pcie-rcar-gen3" for a generic R-Car Gen3 compatible device. When compatible with the generic version, nodes must list the diff --git a/Documentation/devicetree/bindings/arm/ccn.txt b/Documentation/devicetree/bindings/perf/arm-ccn.txt index 43b5a71a5a9d..43b5a71a5a9d 100644 --- a/Documentation/devicetree/bindings/arm/ccn.txt +++ b/Documentation/devicetree/bindings/perf/arm-ccn.txt diff --git a/Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.txt b/Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.txt index a9aa79fb90ed..1aa6f2674af5 100644 --- a/Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.txt @@ -21,7 +21,9 @@ Required properties : - timer: The timeout clock (clk_m). Present if phy_type == utmi. - utmi-pads: The clock needed to access the UTMI pad control registers. Present if phy_type == utmi. - - ulpi-link: The clock Tegra provides to the ULPI PHY (cdev2). + - ulpi-link: The clock Tegra provides to the ULPI PHY (usually pad DAP_MCLK2 + with pad group aka "nvidia,pins" cdev2 and pin mux option config aka + "nvidia,function" pllp_out4). Present if phy_type == ulpi, and ULPI link mode is in use. - resets : Must contain an entry for each entry in reset-names. See ../reset/reset.txt for details. diff --git a/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt b/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt new file mode 100644 index 000000000000..e7caefa0b9c2 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt @@ -0,0 +1,109 @@ +MediaTek XS-PHY binding +-------------------------- + +The XS-PHY controller supports physical layer functionality for USB3.1 +GEN2 controller on MediaTek SoCs. + +Required properties (controller (parent) node): + - compatible : should be "mediatek,<soc-model>-xsphy", "mediatek,xsphy", + soc-model is the name of SoC, such as mt3611 etc; + when using "mediatek,xsphy" compatible string, you need SoC specific + ones in addition, one of: + - "mediatek,mt3611-xsphy" + + - #address-cells, #size-cells : should use the same values as the root node + - ranges: must be present + +Optional properties (controller (parent) node): + - reg : offset and length of register shared by multiple U3 ports, + exclude port's private register, if only U2 ports provided, + shouldn't use the property. + - mediatek,src-ref-clk-mhz : u32, frequency of reference clock for slew rate + calibrate + - mediatek,src-coef : u32, coefficient for slew rate calibrate, depends on + SoC process + +Required nodes : a sub-node is required for each port the controller + provides. Address range information including the usual + 'reg' property is used inside these nodes to describe + the controller's topology. + +Required properties (port (child) node): +- reg : address and length of the register set for the port. +- clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock-names +- clock-names : must contain + "ref": 48M reference clock for HighSpeed analog phy; and 26M + reference clock for SuperSpeedPlus analog phy, sometimes is + 24M, 25M or 27M, depended on platform. +- #phy-cells : should be 1 + cell after port phandle is phy type from: + - PHY_TYPE_USB2 + - PHY_TYPE_USB3 + +The following optional properties are only for debug or HQA test +Optional properties (PHY_TYPE_USB2 port (child) node): +- mediatek,eye-src : u32, the value of slew rate calibrate +- mediatek,eye-vrt : u32, the selection of VRT reference voltage +- mediatek,eye-term : u32, the selection of HS_TX TERM reference voltage +- mediatek,efuse-intr : u32, the selection of Internal Resistor + +Optional properties (PHY_TYPE_USB3 port (child) node): +- mediatek,efuse-intr : u32, the selection of Internal Resistor +- mediatek,efuse-tx-imp : u32, the selection of TX Impedance +- mediatek,efuse-rx-imp : u32, the selection of RX Impedance + +Banks layout of xsphy +------------------------------------------------------------- +port offset bank +u2 port0 0x0000 MISC + 0x0100 FMREG + 0x0300 U2PHY_COM +u2 port1 0x1000 MISC + 0x1100 FMREG + 0x1300 U2PHY_COM +u2 port2 0x2000 MISC + ... +u31 common 0x3000 DIG_GLB + 0x3100 PHYA_GLB +u31 port0 0x3400 DIG_LN_TOP + 0x3500 DIG_LN_TX0 + 0x3600 DIG_LN_RX0 + 0x3700 DIG_LN_DAIF + 0x3800 PHYA_LN +u31 port1 0x3a00 DIG_LN_TOP + 0x3b00 DIG_LN_TX0 + 0x3c00 DIG_LN_RX0 + 0x3d00 DIG_LN_DAIF + 0x3e00 PHYA_LN + ... + +DIG_GLB & PHYA_GLB are shared by U31 ports. + +Example: + +u3phy: usb-phy@11c40000 { + compatible = "mediatek,mt3611-xsphy", "mediatek,xsphy"; + reg = <0 0x11c43000 0 0x0200>; + mediatek,src-ref-clk-mhz = <26>; + mediatek,src-coef = <17>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + u2port0: usb-phy@11c40000 { + reg = <0 0x11c40000 0 0x0400>; + clocks = <&clk48m>; + clock-names = "ref"; + mediatek,eye-src = <4>; + #phy-cells = <1>; + }; + + u3port0: usb-phy@11c43000 { + reg = <0 0x11c43400 0 0x0500>; + clocks = <&clk26m>; + clock-names = "ref"; + mediatek,efuse-intr = <28>; + #phy-cells = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt index dcf1b8f691d5..266a1bb8bb6e 100644 --- a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt +++ b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt @@ -9,7 +9,8 @@ Required properties: "qcom,ipq8074-qmp-pcie-phy" for PCIe phy on IPQ8074 "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996, "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996, - "qcom,qmp-v3-usb3-phy" for USB3 QMP V3 phy. + "qcom,sdm845-qmp-usb3-phy" for USB3 QMP V3 phy on sdm845, + "qcom,sdm845-qmp-usb3-uni-phy" for USB3 QMP V3 UNI phy on sdm845. - reg: offset and length of register set for PHY's common serdes block. diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt index 42c97426836e..03025d97998b 100644 --- a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt +++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt @@ -6,7 +6,7 @@ QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets. Required properties: - compatible: compatible list, contains "qcom,msm8996-qusb2-phy" for 14nm PHY on msm8996, - "qcom,qusb2-v2-phy" for QUSB2 V2 PHY. + "qcom,sdm845-qusb2-phy" for 10nm PHY on sdm845. - reg: offset and length of the PHY register set. - #phy-cells: must be 0. @@ -27,6 +27,27 @@ Optional properties: tuning parameter value for qusb2 phy. - qcom,tcsr-syscon: Phandle to TCSR syscon register region. + - qcom,imp-res-offset-value: It is a 6 bit value that specifies offset to be + added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY + tuning parameter that may vary for different boards of same SOC. + This property is applicable to only QUSB2 v2 PHY (sdm845). + - qcom,hstx-trim-value: It is a 4 bit value that specifies tuning for HSTX + output current. + Possible range is - 15mA to 24mA (stepsize of 600 uA). + See dt-bindings/phy/phy-qcom-qusb2.h for applicable values. + This property is applicable to only QUSB2 v2 PHY (sdm845). + Default value is 22.2mA for sdm845. + - qcom,preemphasis-level: It is a 2 bit value that specifies pre-emphasis level. + Possible range is 0 to 15% (stepsize of 5%). + See dt-bindings/phy/phy-qcom-qusb2.h for applicable values. + This property is applicable to only QUSB2 v2 PHY (sdm845). + Default value is 10% for sdm845. +- qcom,preemphasis-width: It is a 1 bit value that specifies how long the HSTX + pre-emphasis (specified using qcom,preemphasis-level) must be in + effect. Duration could be half-bit of full-bit. + See dt-bindings/phy/phy-qcom-qusb2.h for applicable values. + This property is applicable to only QUSB2 v2 PHY (sdm845). + Default value is full-bit width for sdm845. Example: hsusb_phy: phy@7411000 { diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index ed5eb547afc8..64bc5c2a76da 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -56,9 +56,9 @@ pins it needs, and how they should be configured, with regard to muxer configuration, drive strength and pullups. If one of these options is not set, its actual value will be unspecified. -This driver supports the generic pin multiplexing and configuration -bindings. For details on each properties, you can refer to -./pinctrl-bindings.txt. +Allwinner A1X Pin Controller supports the generic pin multiplexing and +configuration bindings. For details on each properties, you can refer to + ./pinctrl-bindings.txt. Required sub-node properties: - pins diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt index 2c46f30b62c5..9a06e1fdbc42 100644 --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt @@ -11,6 +11,7 @@ Required properies: "st,stm32f429-pinctrl" "st,stm32f469-pinctrl" "st,stm32f746-pinctrl" + "st,stm32f769-pinctrl" "st,stm32h743-pinctrl" "st,stm32mp157-pinctrl" "st,stm32mp157-z-pinctrl" diff --git a/Documentation/devicetree/bindings/pmem/pmem-region.txt b/Documentation/devicetree/bindings/pmem/pmem-region.txt new file mode 100644 index 000000000000..5cfa4f016a00 --- /dev/null +++ b/Documentation/devicetree/bindings/pmem/pmem-region.txt @@ -0,0 +1,65 @@ +Device-tree bindings for persistent memory regions +----------------------------------------------------- + +Persistent memory refers to a class of memory devices that are: + + a) Usable as main system memory (i.e. cacheable), and + b) Retain their contents across power failure. + +Given b) it is best to think of persistent memory as a kind of memory mapped +storage device. To ensure data integrity the operating system needs to manage +persistent regions separately to the normal memory pool. To aid with that this +binding provides a standardised interface for discovering where persistent +memory regions exist inside the physical address space. + +Bindings for the region nodes: +----------------------------- + +Required properties: + - compatible = "pmem-region" + + - reg = <base, size>; + The reg property should specificy an address range that is + translatable to a system physical address range. This address + range should be mappable as normal system memory would be + (i.e cacheable). + + If the reg property contains multiple address ranges + each address range will be treated as though it was specified + in a separate device node. Having multiple address ranges in a + node implies no special relationship between the two ranges. + +Optional properties: + - Any relevant NUMA assocativity properties for the target platform. + + - volatile; This property indicates that this region is actually + backed by non-persistent memory. This lets the OS know that it + may skip the cache flushes required to ensure data is made + persistent after a write. + + If this property is absent then the OS must assume that the region + is backed by non-volatile memory. + +Examples: +-------------------- + + /* + * This node specifies one 4KB region spanning from + * 0x5000 to 0x5fff that is backed by non-volatile memory. + */ + pmem@5000 { + compatible = "pmem-region"; + reg = <0x00005000 0x00001000>; + }; + + /* + * This node specifies two 4KB regions that are backed by + * volatile (normal) memory. + */ + pmem@6000 { + compatible = "pmem-region"; + reg = < 0x00006000 0x00001000 + 0x00008000 0x00001000 >; + volatile; + }; + diff --git a/Documentation/devicetree/bindings/power/power_domain.txt b/Documentation/devicetree/bindings/power/power_domain.txt index f3355313c020..4733f76cbe48 100644 --- a/Documentation/devicetree/bindings/power/power_domain.txt +++ b/Documentation/devicetree/bindings/power/power_domain.txt @@ -127,7 +127,7 @@ inside a PM domain with index 0 of a power controller represented by a node with the label "power". Optional properties: -- required-opp: This contains phandle to an OPP node in another device's OPP +- required-opps: This contains phandle to an OPP node in another device's OPP table. It may contain an array of phandles, where each phandle points to an OPP of a different device. It should not contain multiple phandles to the OPP nodes in the same OPP table. This specifies the minimum required OPP of the @@ -175,14 +175,14 @@ Example: compatible = "foo,i-leak-current"; reg = <0x12350000 0x1000>; power-domains = <&power 0>; - required-opp = <&domain0_opp_0>; + required-opps = <&domain0_opp_0>; }; leaky-device1@12350000 { compatible = "foo,i-leak-current"; reg = <0x12350000 0x1000>; power-domains = <&power 1>; - required-opp = <&domain1_opp_1>; + required-opps = <&domain1_opp_1>; }; [1]. Documentation/devicetree/bindings/power/domain-idle-state.txt diff --git a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt index 8690f10426a3..ab399e559257 100644 --- a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt +++ b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt @@ -17,7 +17,9 @@ Required properties: - "renesas,r8a7794-sysc" (R-Car E2) - "renesas,r8a7795-sysc" (R-Car H3) - "renesas,r8a7796-sysc" (R-Car M3-W) + - "renesas,r8a77965-sysc" (R-Car M3-N) - "renesas,r8a77970-sysc" (R-Car V3M) + - "renesas,r8a77980-sysc" (R-Car V3H) - "renesas,r8a77995-sysc" (R-Car D3) - reg: Address start and address range for the device. - #power-domain-cells: Must be 1. diff --git a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt index 4a4766e9c254..e66fd4eab71c 100644 --- a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt +++ b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt @@ -31,6 +31,8 @@ SoC is on the same page. Required properties: - compatible: should be one of: + - "rockchip,px30-io-voltage-domain" for px30 + - "rockchip,px30-pmu-io-voltage-domain" for px30 pmu-domains - "rockchip,rk3188-io-voltage-domain" for rk3188 - "rockchip,rk3228-io-voltage-domain" for rk3228 - "rockchip,rk3288-io-voltage-domain" for rk3288 @@ -51,6 +53,19 @@ a phandle the relevant regulator. All specified supplies must be able to report their voltage. The IO Voltage Domain for any non-specified supplies will be not be touched. +Possible supplies for PX30: +- vccio6-supply: The supply connected to VCCIO6. +- vccio1-supply: The supply connected to VCCIO1. +- vccio2-supply: The supply connected to VCCIO2. +- vccio3-supply: The supply connected to VCCIO3. +- vccio4-supply: The supply connected to VCCIO4. +- vccio5-supply: The supply connected to VCCIO5. +- vccio-oscgpi-supply: The supply connected to VCCIO_OSCGPI. + +Possible supplies for PX30 pmu-domains: +- pmuio1-supply: The supply connected to PMUIO1. +- pmuio2-supply: The supply connected to PMUIO2. + Possible supplies for rk3188: - ap0-supply: The supply connected to AP0_VCC. - ap1-supply: The supply connected to AP1_VCC. diff --git a/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt b/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt new file mode 100644 index 000000000000..7d9d3f90641b --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt @@ -0,0 +1,25 @@ +Ingenic JZ47xx PWM Controller +============================= + +Required properties: +- compatible: One of: + * "ingenic,jz4740-pwm" + * "ingenic,jz4770-pwm" + * "ingenic,jz4780-pwm" +- #pwm-cells: Should be 3. See pwm.txt in this directory for a description + of the cells format. +- clocks : phandle to the external clock. +- clock-names : Should be "ext". + + +Example: + + pwm: pwm@10002000 { + compatible = "ingenic,jz4740-pwm"; + reg = <0x10002000 0x1000>; + + #pwm-cells = <3>; + + clocks = <&ext>; + clock-names = "ext"; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt b/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt index f8338d11fd2b..bd23302e84be 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt @@ -7,6 +7,8 @@ See ../mfd/stm32-lptimer.txt for details about the parent node. Required parameters: - compatible: Must be "st,stm32-pwm-lp". +- #pwm-cells: Should be set to 3. This PWM chip uses the default 3 cells + bindings defined in pwm.txt. Optional properties: - pinctrl-names: Set to "default". @@ -18,6 +20,7 @@ Example: ... pwm { compatible = "st,stm32-pwm-lp"; + #pwm-cells = <3>; pinctrl-names = "default"; pinctrl-0 = <&lppwm1_pins>; }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt b/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt index 51ff54c8b8ef..2a1affbff45e 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt @@ -7,6 +7,8 @@ Required properties: - "allwinner,sun5i-a13-pwm" - "allwinner,sun7i-a20-pwm" - "allwinner,sun8i-h3-pwm" + - "allwinner,sun50i-a64-pwm", "allwinner,sun5i-a13-pwm" + - "allwinner,sun50i-h5-pwm", "allwinner,sun5i-a13-pwm" - reg: physical base address and length of the controller's registers - #pwm-cells: should be 3. See pwm.txt in this directory for a description of the cells format. diff --git a/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt b/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt index 74c118015980..35a3b9761ee5 100644 --- a/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt +++ b/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt @@ -2,6 +2,8 @@ Required Properties: - compatible: should be "renesas,pwm-rcar" and one of the following. + - "renesas,pwm-r8a7743": for RZ/G1M + - "renesas,pwm-r8a7745": for RZ/G1E - "renesas,pwm-r8a7778": for R-Car M1A - "renesas,pwm-r8a7779": for R-Car H1 - "renesas,pwm-r8a7790": for R-Car H2 @@ -9,6 +11,7 @@ Required Properties: - "renesas,pwm-r8a7794": for R-Car E2 - "renesas,pwm-r8a7795": for R-Car H3 - "renesas,pwm-r8a7796": for R-Car M3-W + - "renesas,pwm-r8a77965": for R-Car M3-N - "renesas,pwm-r8a77995": for R-Car D3 - reg: base address and length of the registers block for the PWM. - #pwm-cells: should be 2. See pwm.txt in this directory for a description of @@ -17,13 +20,15 @@ Required Properties: - pinctrl-0: phandle, referring to a default pin configuration node. - pinctrl-names: Set to "default". -Example: R8A7790 (R-Car H2) PWM Timer node +Example: R8A7743 (RZ/G1M) PWM Timer node pwm0: pwm@e6e30000 { - compatible = "renesas,pwm-r8a7790", "renesas,pwm-rcar"; + compatible = "renesas,pwm-r8a7743", "renesas,pwm-rcar"; reg = <0 0xe6e30000 0 0x8>; + clocks = <&cpg CPG_MOD 523>; + power-domains = <&sysc R8A7743_PD_ALWAYS_ON>; + resets = <&cpg 523>; #pwm-cells = <2>; - clocks = <&mstp5_clks R8A7790_CLK_PWM>; pinctrl-0 = <&pwm0_pins>; pinctrl-names = "default"; }; diff --git a/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt b/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt index 1aadc804dae4..d53a16715da6 100644 --- a/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt @@ -3,10 +3,12 @@ Required Properties: - compatible: should be one of the following. - - "renesas,tpu-r8a73a4": for R8A77A4 (R-Mobile APE6) compatible PWM controller. + - "renesas,tpu-r8a73a4": for R8A73A4 (R-Mobile APE6) compatible PWM controller. - "renesas,tpu-r8a7740": for R8A7740 (R-Mobile A1) compatible PWM controller. + - "renesas,tpu-r8a7743": for R8A7743 (RZ/G1M) compatible PWM controller. + - "renesas,tpu-r8a7745": for R8A7745 (RZ/G1E) compatible PWM controller. - "renesas,tpu-r8a7790": for R8A7790 (R-Car H2) compatible PWM controller. - - "renesas,tpu": for generic R-Car TPU PWM controller. + - "renesas,tpu": for generic R-Car and RZ/G1 TPU PWM controller. - reg: Base address and length of each memory resource used by the PWM controller hardware module. @@ -18,10 +20,10 @@ Required Properties: Please refer to pwm.txt in this directory for details of the common PWM bindings used by client devices. -Example: R8A7740 (R-Car A1) TPU controller node +Example: R8A7740 (R-Mobile A1) TPU controller node tpu: pwm@e6600000 { compatible = "renesas,tpu-r8a7740", "renesas,tpu"; - reg = <0xe6600000 0x100>; + reg = <0xe6600000 0x148>; #pwm-cells = <3>; }; diff --git a/Documentation/devicetree/bindings/reset/renesas,rst.txt b/Documentation/devicetree/bindings/reset/renesas,rst.txt index a8014f3ab8ba..294a0dae106a 100644 --- a/Documentation/devicetree/bindings/reset/renesas,rst.txt +++ b/Documentation/devicetree/bindings/reset/renesas,rst.txt @@ -26,7 +26,9 @@ Required properties: - "renesas,r8a7794-rst" (R-Car E2) - "renesas,r8a7795-rst" (R-Car H3) - "renesas,r8a7796-rst" (R-Car M3-W) + - "renesas,r8a77965-rst" (R-Car M3-N) - "renesas,r8a77970-rst" (R-Car V3M) + - "renesas,r8a77980-rst" (R-Car V3H) - "renesas,r8a77995-rst" (R-Car D3) - reg: Address start and address range for the device. diff --git a/Documentation/devicetree/bindings/reset/st,stm32mp1-rcc.txt b/Documentation/devicetree/bindings/reset/st,stm32mp1-rcc.txt new file mode 100644 index 000000000000..b4edaf7c7ff3 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/st,stm32mp1-rcc.txt @@ -0,0 +1,6 @@ +STMicroelectronics STM32MP1 Peripheral Reset Controller +======================================================= + +The RCC IP is both a reset and a clock controller. + +Please see Documentation/devicetree/bindings/clock/st,stm32mp1-rcc.txt diff --git a/Documentation/devicetree/bindings/rtc/isil,isl12026.txt b/Documentation/devicetree/bindings/rtc/isil,isl12026.txt new file mode 100644 index 000000000000..2e0be45193bb --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/isil,isl12026.txt @@ -0,0 +1,28 @@ +ISL12026 I2C RTC/EEPROM + +ISL12026 is an I2C RTC/EEPROM combination device. The RTC and control +registers respond at bus address 0x6f, and the EEPROM array responds +at bus address 0x57. The canonical "reg" value will be for the RTC portion. + +Required properties supported by the device: + + - "compatible": must be "isil,isl12026" + - "reg": I2C bus address of the device (always 0x6f) + +Optional properties: + + - "isil,pwr-bsw": If present PWR.BSW bit must be set to the specified + value for proper operation. + + - "isil,pwr-sbib": If present PWR.SBIB bit must be set to the specified + value for proper operation. + + +Example: + + rtc@6f { + compatible = "isil,isl12026"; + reg = <0x6f>; + isil,pwr-bsw = <0>; + isil,pwr-sbib = <1>; + } diff --git a/Documentation/devicetree/bindings/serial/amlogic,meson-uart.txt b/Documentation/devicetree/bindings/serial/amlogic,meson-uart.txt index 8ff65fa632fd..c06c045126fc 100644 --- a/Documentation/devicetree/bindings/serial/amlogic,meson-uart.txt +++ b/Documentation/devicetree/bindings/serial/amlogic,meson-uart.txt @@ -21,7 +21,7 @@ Required properties: - interrupts : identifier to the device interrupt - clocks : a list of phandle + clock-specifier pairs, one for each entry in clock names. -- clocks-names : +- clock-names : * "xtal" for external xtal clock identifier * "pclk" for the bus core clock, either the clk81 clock or the gate clock * "baud" for the source of the baudrate generator, can be either the xtal diff --git a/Documentation/devicetree/bindings/serial/mvebu-uart.txt b/Documentation/devicetree/bindings/serial/mvebu-uart.txt index 2ae2fee7e023..b7e0e32b9ac6 100644 --- a/Documentation/devicetree/bindings/serial/mvebu-uart.txt +++ b/Documentation/devicetree/bindings/serial/mvebu-uart.txt @@ -24,7 +24,7 @@ Required properties: - Must contain two elements for the extended variant of the IP (marvell,armada-3700-uart-ext): "uart-tx" and "uart-rx", respectively the UART TX interrupt and the UART RX interrupt. A - corresponding interrupts-names property must be defined. + corresponding interrupt-names property must be defined. - For backward compatibility reasons, a single element interrupts property is also supported for the standard variant of the IP, containing only the UART sum interrupt. This form is deprecated diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index ad962f4ec3aa..106808b55b6d 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -17,6 +17,8 @@ Required properties: - "renesas,scifa-r8a7745" for R8A7745 (RZ/G1E) SCIFA compatible UART. - "renesas,scifb-r8a7745" for R8A7745 (RZ/G1E) SCIFB compatible UART. - "renesas,hscif-r8a7745" for R8A7745 (RZ/G1E) HSCIF compatible UART. + - "renesas,scif-r8a77470" for R8A77470 (RZ/G1C) SCIF compatible UART. + - "renesas,hscif-r8a77470" for R8A77470 (RZ/G1C) HSCIF compatible UART. - "renesas,scif-r8a7778" for R8A7778 (R-Car M1) SCIF compatible UART. - "renesas,scif-r8a7779" for R8A7779 (R-Car H1) SCIF compatible UART. - "renesas,scif-r8a7790" for R8A7790 (R-Car H2) SCIF compatible UART. @@ -41,6 +43,8 @@ Required properties: - "renesas,hscif-r8a7795" for R8A7795 (R-Car H3) HSCIF compatible UART. - "renesas,scif-r8a7796" for R8A7796 (R-Car M3-W) SCIF compatible UART. - "renesas,hscif-r8a7796" for R8A7796 (R-Car M3-W) HSCIF compatible UART. + - "renesas,scif-r8a77965" for R8A77965 (R-Car M3-N) SCIF compatible UART. + - "renesas,hscif-r8a77965" for R8A77965 (R-Car M3-N) HSCIF compatible UART. - "renesas,scif-r8a77970" for R8A77970 (R-Car V3M) SCIF compatible UART. - "renesas,hscif-r8a77970" for R8A77970 (R-Car V3M) HSCIF compatible UART. - "renesas,scif-r8a77980" for R8A77980 (R-Car V3H) SCIF compatible UART. diff --git a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt index 76bf45b893fa..d6fe16f094af 100644 --- a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt +++ b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt @@ -21,6 +21,8 @@ Required properties: - "mediatek,mt2712-scpsys" - "mediatek,mt6797-scpsys" - "mediatek,mt7622-scpsys" + - "mediatek,mt7623-scpsys", "mediatek,mt2701-scpsys": For MT7623 SoC + - "mediatek,mt7623a-scpsys": For MT7623A SoC - "mediatek,mt8173-scpsys" - #power-domain-cells: Must be 1 - reg: Address range of the SCPSYS unit @@ -28,10 +30,11 @@ Required properties: - clock, clock-names: clocks according to the common clock binding. These are clocks which hardware needs to be enabled before enabling certain power domains. - Required clocks for MT2701: "mm", "mfg", "ethif" + Required clocks for MT2701 or MT7623: "mm", "mfg", "ethif" Required clocks for MT2712: "mm", "mfg", "venc", "jpgdec", "audio", "vdec" Required clocks for MT6797: "mm", "mfg", "vdec" Required clocks for MT7622: "hif_sel" + Required clocks for MT7622A: "ethif" Required clocks for MT8173: "mm", "mfg", "venc", "venc_lt" Optional properties: diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt new file mode 100644 index 000000000000..bcc612cc7423 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt @@ -0,0 +1,84 @@ +Qualcomm APR (Asynchronous Packet Router) binding + +This binding describes the Qualcomm APR. APR is a IPC protocol for +communication between Application processor and QDSP. APR is mainly +used for audio/voice services on the QDSP. + +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be "qcom,apr-v<VERSION-NUMBER>", example "qcom,apr-v2" + +- reg + Usage: required + Value type: <u32> + Definition: Destination processor ID. + Possible values are : + 1 - APR simulator + 2 - PC + 3 - MODEM + 4 - ADSP + 5 - APPS + 6 - MODEM2 + 7 - APPS2 + += APR SERVICES +Each subnode of the APR node represents service tied to this apr. The name +of the nodes are not important. The properties of these nodes are defined +by the individual bindings for the specific service +- All APR services MUST contain the following property: + +- reg + Usage: required + Value type: <u32> + Definition: APR Service ID + Possible values are : + 3 - DSP Core Service + 4 - Audio Front End Service. + 5 - Voice Stream Manager Service. + 6 - Voice processing manager. + 7 - Audio Stream Manager Service. + 8 - Audio Device Manager Service. + 9 - Multimode voice manager. + 10 - Core voice stream. + 11 - Core voice processor. + 12 - Ultrasound stream manager. + 13 - Listen stream manager. + += EXAMPLE +The following example represents a QDSP based sound card on a MSM8996 device +which uses apr as communication between Apps and QDSP. + + apr@4 { + compatible = "qcom,apr-v2"; + reg = <APR_DOMAIN_ADSP>; + + q6core@3 { + compatible = "qcom,q6core"; + reg = <APR_SVC_ADSP_CORE>; + }; + + q6afe@4 { + compatible = "qcom,q6afe"; + reg = <APR_SVC_AFE>; + + dais { + #sound-dai-cells = <1>; + hdmi@1 { + reg = <1>; + }; + }; + }; + + q6asm@7 { + compatible = "qcom,q6asm"; + reg = <APR_SVC_ASM>; + ... + }; + + q6adm@8 { + compatible = "qcom,q6adm"; + reg = <APR_SVC_ADM>; + ... + }; + }; diff --git a/Documentation/devicetree/bindings/sound/adi,ssm2305.txt b/Documentation/devicetree/bindings/sound/adi,ssm2305.txt new file mode 100644 index 000000000000..a9c9d83c8a30 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/adi,ssm2305.txt @@ -0,0 +1,14 @@ +Analog Devices SSM2305 Speaker Amplifier +======================================== + +Required properties: + - compatible : "adi,ssm2305" + - shutdown-gpios : The gpio connected to the shutdown pin. + The gpio signal is ACTIVE_LOW. + +Example: + +ssm2305: analog-amplifier { + compatible = "adi,ssm2305"; + shutdown-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>; +}; diff --git a/Documentation/devicetree/bindings/sound/atmel-i2s.txt b/Documentation/devicetree/bindings/sound/atmel-i2s.txt new file mode 100644 index 000000000000..735368b8a73f --- /dev/null +++ b/Documentation/devicetree/bindings/sound/atmel-i2s.txt @@ -0,0 +1,47 @@ +* Atmel I2S controller + +Required properties: +- compatible: Should be "atmel,sama5d2-i2s". +- reg: Should be the physical base address of the controller and the + length of memory mapped region. +- interrupts: Should contain the interrupt for the controller. +- dmas: Should be one per channel name listed in the dma-names property, + as described in atmel-dma.txt and dma.txt files. +- dma-names: Two dmas have to be defined, "tx" and "rx". + This IP also supports one shared channel for both rx and tx; + if this mode is used, one "rx-tx" name must be used. +- clocks: Must contain an entry for each entry in clock-names. + Please refer to clock-bindings.txt. +- clock-names: Should be one of each entry matching the clocks phandles list: + - "pclk" (peripheral clock) Required. + - "gclk" (generated clock) Optional (1). + - "aclk" (Audio PLL clock) Optional (1). + - "muxclk" (I2S mux clock) Optional (1). + +Optional properties: +- pinctrl-0: Should specify pin control groups used for this controller. +- princtrl-names: Should contain only one value - "default". + + +(1) : Only the peripheral clock is required. The generated clock, the Audio + PLL clock adn the I2S mux clock are optional and should only be set + together, when Master Mode is required. + +Example: + + i2s@f8050000 { + compatible = "atmel,sama5d2-i2s"; + reg = <0xf8050000 0x300>; + interrupts = <54 IRQ_TYPE_LEVEL_HIGH 7>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(31))>, + <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(32))>; + dma-names = "tx", "rx"; + clocks = <&i2s0_clk>, <&i2s0_gclk>, <&audio_pll_pmc>, <&i2s0muxck>; + clock-names = "pclk", "gclk", "aclk", "muxclk"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2s0_default>; + }; diff --git a/Documentation/devicetree/bindings/sound/brcm,bcm2835-i2s.txt b/Documentation/devicetree/bindings/sound/brcm,bcm2835-i2s.txt index 65783de0aedf..7bb0362828ec 100644 --- a/Documentation/devicetree/bindings/sound/brcm,bcm2835-i2s.txt +++ b/Documentation/devicetree/bindings/sound/brcm,bcm2835-i2s.txt @@ -2,9 +2,8 @@ Required properties: - compatible: "brcm,bcm2835-i2s" -- reg: A list of base address and size entries: - * The first entry should cover the PCM registers - * The second entry should cover the PCM clock registers +- reg: Should contain PCM registers location and length. +- clocks: the (PCM) clock to use - dmas: List of DMA controller phandle and DMA request line ordered pairs. - dma-names: Identifier string for each DMA request line in the dmas property. These strings correspond 1:1 with the ordered pairs in dmas. @@ -16,8 +15,8 @@ Example: bcm2835_i2s: i2s@7e203000 { compatible = "brcm,bcm2835-i2s"; - reg = <0x7e203000 0x20>, - <0x7e101098 0x02>; + reg = <0x7e203000 0x24>; + clocks = <&clocks BCM2835_CLOCK_PCM>; dmas = <&dma 2>, <&dma 3>; diff --git a/Documentation/devicetree/bindings/sound/cs42xx8.txt b/Documentation/devicetree/bindings/sound/cs42xx8.txt index f631fbca6284..8619a156d038 100644 --- a/Documentation/devicetree/bindings/sound/cs42xx8.txt +++ b/Documentation/devicetree/bindings/sound/cs42xx8.txt @@ -16,7 +16,7 @@ Required properties: Example: -codec: cs42888@48 { +cs42888: codec@48 { compatible = "cirrus,cs42888"; reg = <0x48>; clocks = <&codec_mclk 0>; diff --git a/Documentation/devicetree/bindings/sound/fsl,asrc.txt b/Documentation/devicetree/bindings/sound/fsl,asrc.txt index f5a14115b459..1d4d9f938689 100644 --- a/Documentation/devicetree/bindings/sound/fsl,asrc.txt +++ b/Documentation/devicetree/bindings/sound/fsl,asrc.txt @@ -31,14 +31,16 @@ Required properties: it. This property is optional depending on the SoC design. - - big-endian : If this property is absent, the little endian mode - will be in use as default. Otherwise, the big endian - mode will be in use for all the device registers. - - fsl,asrc-rate : Defines a mutual sample rate used by DPCM Back Ends. - fsl,asrc-width : Defines a mutual sample width used by DPCM Back Ends. +Optional properties: + + - big-endian : If this property is absent, the little endian mode + will be in use as default. Otherwise, the big endian + mode will be in use for all the device registers. + Example: asrc: asrc@2034000 { diff --git a/Documentation/devicetree/bindings/sound/fsl,esai.txt b/Documentation/devicetree/bindings/sound/fsl,esai.txt index cacd18bb9ba6..5b9914367610 100644 --- a/Documentation/devicetree/bindings/sound/fsl,esai.txt +++ b/Documentation/devicetree/bindings/sound/fsl,esai.txt @@ -42,6 +42,8 @@ Required properties: means all the settings for Receiving would be duplicated from Transmition related registers. +Optional properties: + - big-endian : If this property is absent, the native endian mode will be in use as default, or the big endian mode will be in use for all the device registers. diff --git a/Documentation/devicetree/bindings/sound/fsl,spdif.txt b/Documentation/devicetree/bindings/sound/fsl,spdif.txt index 38cfa7573441..8b324f82a782 100644 --- a/Documentation/devicetree/bindings/sound/fsl,spdif.txt +++ b/Documentation/devicetree/bindings/sound/fsl,spdif.txt @@ -33,6 +33,8 @@ Required properties: it. This property is optional depending on the SoC design. +Optional properties: + - big-endian : If this property is absent, the native endian mode will be in use as default, or the big endian mode will be in use for all the device registers. diff --git a/Documentation/devicetree/bindings/sound/fsl-sai.txt b/Documentation/devicetree/bindings/sound/fsl-sai.txt index 740b467adf7d..dd9e59738e08 100644 --- a/Documentation/devicetree/bindings/sound/fsl-sai.txt +++ b/Documentation/devicetree/bindings/sound/fsl-sai.txt @@ -28,9 +28,6 @@ Required properties: pinctrl-names. See ../pinctrl/pinctrl-bindings.txt for details of the property values. - - big-endian : Boolean property, required if all the FTM_PWM - registers are big-endian rather than little-endian. - - lsb-first : Configures whether the LSB or the MSB is transmitted first for the fifo data. If this property is absent, the MSB is transmitted first as default, or the LSB @@ -48,6 +45,11 @@ Required properties: receive data by following their own bit clocks and frame sync clocks separately. +Optional properties: + + - big-endian : Boolean property, required if all the SAI + registers are big-endian rather than little-endian. + Optional properties (for mx6ul): - fsl,sai-mclk-direction-output: This is a boolean property. If present, diff --git a/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt b/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt index e2f7f4951215..560762e0a168 100644 --- a/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt +++ b/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt @@ -1,7 +1,9 @@ Mediatek AFE PCM controller for mt2701 Required properties: -- compatible = "mediatek,mt2701-audio"; +- compatible: should be one of the followings. + - "mediatek,mt2701-audio" + - "mediatek,mt7622-audio" - interrupts: should contain AFE and ASYS interrupts - interrupt-names: should be "afe" and "asys" - power-domains: should define the power domain diff --git a/Documentation/devicetree/bindings/sound/mt6351.txt b/Documentation/devicetree/bindings/sound/mt6351.txt new file mode 100644 index 000000000000..7fb2cb99245e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/mt6351.txt @@ -0,0 +1,16 @@ +Mediatek MT6351 Audio Codec + +The communication between MT6351 and SoC is through Mediatek PMIC wrapper. +For more detail, please visit Mediatek PMIC wrapper documentation. + +Must be a child node of PMIC wrapper. + +Required properties: + +- compatible : "mediatek,mt6351-sound". + +Example: + +mt6351_snd { + compatible = "mediatek,mt6351-sound"; +}; diff --git a/Documentation/devicetree/bindings/sound/mt6797-afe-pcm.txt b/Documentation/devicetree/bindings/sound/mt6797-afe-pcm.txt new file mode 100644 index 000000000000..0ae29de15bfd --- /dev/null +++ b/Documentation/devicetree/bindings/sound/mt6797-afe-pcm.txt @@ -0,0 +1,42 @@ +Mediatek AFE PCM controller for mt6797 + +Required properties: +- compatible = "mediatek,mt6797-audio"; +- reg: register location and size +- interrupts: should contain AFE interrupt +- power-domains: should define the power domain +- clocks: Must contain an entry for each entry in clock-names +- clock-names: should have these clock names: + "infra_sys_audio_clk", + "infra_sys_audio_26m", + "mtkaif_26m_clk", + "top_mux_audio", + "top_mux_aud_intbus", + "top_sys_pll3_d4", + "top_sys_pll1_d4", + "top_clk26m_clk"; + +Example: + + afe: mt6797-afe-pcm@11220000 { + compatible = "mediatek,mt6797-audio"; + reg = <0 0x11220000 0 0x1000>; + interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT6797_POWER_DOMAIN_AUDIO>; + clocks = <&infrasys CLK_INFRA_AUDIO>, + <&infrasys CLK_INFRA_AUDIO_26M>, + <&infrasys CLK_INFRA_AUDIO_26M_PAD_TOP>, + <&topckgen CLK_TOP_MUX_AUDIO>, + <&topckgen CLK_TOP_MUX_AUD_INTBUS>, + <&topckgen CLK_TOP_SYSPLL3_D4>, + <&topckgen CLK_TOP_SYSPLL1_D4>, + <&clk26m>; + clock-names = "infra_sys_audio_clk", + "infra_sys_audio_26m", + "mtkaif_26m_clk", + "top_mux_audio", + "top_mux_aud_intbus", + "top_sys_pll3_d4", + "top_sys_pll1_d4", + "top_clk26m_clk"; + }; diff --git a/Documentation/devicetree/bindings/sound/mt6797-mt6351.txt b/Documentation/devicetree/bindings/sound/mt6797-mt6351.txt new file mode 100644 index 000000000000..1d95a8840f19 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/mt6797-mt6351.txt @@ -0,0 +1,14 @@ +MT6797 with MT6351 CODEC + +Required properties: +- compatible: "mediatek,mt6797-mt6351-sound" +- mediatek,platform: the phandle of MT6797 ASoC platform +- mediatek,audio-codec: the phandles of MT6351 codec + +Example: + + sound { + compatible = "mediatek,mt6797-mt6351-sound"; + mediatek,audio-codec = <&mt6351_snd>; + mediatek,platform = <&afe>; + }; diff --git a/Documentation/devicetree/bindings/sound/qcom,apq8096.txt b/Documentation/devicetree/bindings/sound/qcom,apq8096.txt new file mode 100644 index 000000000000..aa54e49fc8a2 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,apq8096.txt @@ -0,0 +1,109 @@ +* Qualcomm Technologies APQ8096 ASoC sound card driver + +This binding describes the APQ8096 sound card, which uses qdsp for audio. + +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be "qcom,apq8096-sndcard" + +- qcom,audio-routing: + Usage: Optional + Value type: <stringlist> + Definition: A list of the connections between audio components. + Each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source. Valid names could be power supplies, MicBias + of codec and the jacks on the board: + Valid names include: + + Board Connectors: + "Headphone Left" + "Headphone Right" + "Earphone" + "Line Out1" + "Line Out2" + "Line Out3" + "Line Out4" + "Analog Mic1" + "Analog Mic2" + "Analog Mic3" + "Analog Mic4" + "Analog Mic5" + "Analog Mic6" + "Digital Mic2" + "Digital Mic3" + + Audio pins and MicBias on WCD9335 Codec: + "MIC_BIAS1 + "MIC_BIAS2" + "MIC_BIAS3" + "MIC_BIAS4" + "AMIC1" + "AMIC2" + "AMIC3" + "AMIC4" + "AMIC5" + "AMIC6" + "AMIC6" + "DMIC1" + "DMIC2" + "DMIC3" += dailinks +Each subnode of sndcard represents either a dailink, and subnodes of each +dailinks would be cpu/codec/platform dais. + +- link-name: + Usage: required + Value type: <string> + Definition: User friendly name for dai link + += CPU, PLATFORM, CODEC dais subnodes +- cpu: + Usage: required + Value type: <subnode> + Definition: cpu dai sub-node + +- codec: + Usage: Optional + Value type: <subnode> + Definition: codec dai sub-node + +- platform: + Usage: Optional + Value type: <subnode> + Definition: platform dai sub-node + +- sound-dai: + Usage: required + Value type: <phandle with arguments> + Definition: dai phandle/s and port of CPU/CODEC/PLATFORM node. + +Example: + +audio { + compatible = "qcom,apq8096-sndcard"; + qcom,model = "DB820c"; + + mm1-dai-link { + link-name = "MultiMedia1"; + cpu { + sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>; + }; + }; + + hdmi-dai-link { + link-name = "HDMI Playback"; + cpu { + sound-dai = <&q6afe HDMI_RX>; + }; + + platform { + sound-dai = <&q6adm>; + }; + + codec { + sound-dai = <&hdmi 0>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/qcom,q6adm.txt b/Documentation/devicetree/bindings/sound/qcom,q6adm.txt new file mode 100644 index 000000000000..cb709e5dbc44 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,q6adm.txt @@ -0,0 +1,33 @@ +Qualcomm Audio Device Manager (Q6ADM) binding + +Q6ADM is one of the APR audio service on Q6DSP. +Please refer to qcom,apr.txt for details of the coommon apr service bindings +used by the apr service device. + +- but must contain the following property: + +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be "qcom,q6adm-v<MAJOR-NUMBER>.<MINOR-NUMBER>". + Or "qcom,q6adm" where the version number can be queried + from DSP. + example "qcom,q6adm-v2.0" + + += ADM routing +"routing" subnode of the ADM node represents adm routing specific configuration + +- #sound-dai-cells + Usage: required + Value type: <u32> + Definition: Must be 0 + += EXAMPLE +q6adm@8 { + compatible = "qcom,q6adm"; + reg = <APR_SVC_ADM>; + q6routing: routing { + #sound-dai-cells = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/qcom,q6afe.txt b/Documentation/devicetree/bindings/sound/qcom,q6afe.txt new file mode 100644 index 000000000000..bdbf87df8c0b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,q6afe.txt @@ -0,0 +1,172 @@ +Qualcomm Audio Front End (Q6AFE) binding + +AFE is one of the APR audio service on Q6DSP +Please refer to qcom,apr.txt for details of the common apr service bindings +used by all apr services. Must contain the following properties. + +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be "qcom,q6afe-v<MAJOR-NUMBER>.<MINOR-NUMBER>" + Or "qcom,q6afe" where the version number can be queried + from DSP. + example "qcom,q6afe" + += AFE DAIs (Digial Audio Interface) +"dais" subnode of the AFE node. It represents afe dais, each afe dai is a +subnode of "dais" representing board specific dai setup. +"dais" node should have following properties followed by dai children. + +- #sound-dai-cells + Usage: required + Value type: <u32> + Definition: Must be 1 + +- #address-cells + Usage: required + Value type: <u32> + Definition: Must be 1 + +- #size-cells + Usage: required + Value type: <u32> + Definition: Must be 0 + +== AFE DAI is subnode of "dais" and represent a dai, it includes board specific +configuration of each dai. Must contain the following properties. + +- reg + Usage: required + Value type: <u32> + Definition: Must be dai id + +- qcom,sd-lines + Usage: required for mi2s interface + Value type: <prop-encoded-array> + Definition: Must be list of serial data lines used by this dai. + should be one or more of the 1-4 sd lines. + + - qcom,tdm-sync-mode: + Usage: required for tdm interface + Value type: <prop-encoded-array> + Definition: Synchronization mode. + 0 - Short sync bit mode + 1 - Long sync mode + 2 - Short sync slot mode + + - qcom,tdm-sync-src: + Usage: required for tdm interface + Value type: <prop-encoded-array> + Definition: Synchronization source. + 0 - External source + 1 - Internal source + + - qcom,tdm-data-out: + Usage: required for tdm interface + Value type: <prop-encoded-array> + Definition: Data out signal to drive with other masters. + 0 - Disable + 1 - Enable + + - qcom,tdm-invert-sync: + Usage: required for tdm interface + Value type: <prop-encoded-array> + Definition: Invert the sync. + 0 - Normal + 1 - Invert + + - qcom,tdm-data-delay: + Usage: required for tdm interface + Value type: <prop-encoded-array> + Definition: Number of bit clock to delay data + with respect to sync edge. + 0 - 0 bit clock cycle + 1 - 1 bit clock cycle + 2 - 2 bit clock cycle + + - qcom,tdm-data-align: + Usage: required for tdm interface + Value type: <prop-encoded-array> + Definition: Indicate how data is packed + within the slot. For example, 32 slot width in case of + sample bit width is 24. + 0 - MSB + 1 - LSB + += EXAMPLE + +q6afe@4 { + compatible = "qcom,q6afe"; + reg = <APR_SVC_AFE>; + + dais { + #sound-dai-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + + hdmi@1 { + reg = <1>; + }; + + tdm@24 { + reg = <24>; + qcom,tdm-sync-mode = <1>: + qcom,tdm-sync-src = <1>; + qcom,tdm-data-out = <0>; + qcom,tdm-invert-sync = <1>; + qcom,tdm-data-delay = <1>; + qcom,tdm-data-align = <0>; + + }; + + tdm@25 { + reg = <25>; + qcom,tdm-sync-mode = <1>: + qcom,tdm-sync-src = <1>; + qcom,tdm-data-out = <0>; + qcom,tdm-invert-sync = <1>; + qcom,tdm-data-delay <1>: + qcom,tdm-data-align = <0>; + }; + + prim-mi2s-rx@16 { + reg = <16>; + qcom,sd-lines = <1 3>; + }; + + prim-mi2s-tx@17 { + reg = <17>; + qcom,sd-lines = <2>; + }; + + sec-mi2s-rx@18 { + reg = <18>; + qcom,sd-lines = <1 4>; + }; + + sec-mi2s-tx@19 { + reg = <19>; + qcom,sd-lines = <2>; + }; + + tert-mi2s-rx@20 { + reg = <20>; + qcom,sd-lines = <2 4>; + }; + + tert-mi2s-tx@21 { + reg = <21>; + qcom,sd-lines = <1>; + }; + + quat-mi2s-rx@22 { + reg = <22>; + qcom,sd-lines = <1>; + }; + + quat-mi2s-tx@23 { + reg = <23>; + qcom,sd-lines = <2>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/qcom,q6asm.txt b/Documentation/devicetree/bindings/sound/qcom,q6asm.txt new file mode 100644 index 000000000000..2178eb91146f --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,q6asm.txt @@ -0,0 +1,33 @@ +Qualcomm Audio Stream Manager (Q6ASM) binding + +Q6ASM is one of the APR audio service on Q6DSP. +Please refer to qcom,apr.txt for details of the common apr service bindings +used by the apr service device. + +- but must contain the following property: + +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be "qcom,q6asm-v<MAJOR-NUMBER>.<MINOR-NUMBER>". + Or "qcom,q6asm" where the version number can be queried + from DSP. + example "qcom,q6asm-v2.0" + += ASM DAIs (Digial Audio Interface) +"dais" subnode of the ASM node represents dai specific configuration + +- #sound-dai-cells + Usage: required + Value type: <u32> + Definition: Must be 1 + += EXAMPLE + +q6asm@7 { + compatible = "qcom,q6asm"; + reg = <APR_SVC_ASM>; + q6asmdai: dais { + #sound-dai-cells = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/qcom,q6core.txt b/Documentation/devicetree/bindings/sound/qcom,q6core.txt new file mode 100644 index 000000000000..7f36ff8bec18 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,q6core.txt @@ -0,0 +1,21 @@ +Qualcomm ADSP Core service binding + +Q6CORE is one of the APR audio service on Q6DSP. +Please refer to qcom,apr.txt for details of the common apr service bindings +used by the apr service device. + +- but must contain the following property: + +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be "qcom,q6core-v<MAJOR-NUMBER>.<MINOR-NUMBER>". + Or "qcom,q6core" where the version number can be queried + from DSP. + example "qcom,q6core-v2.0" + += EXAMPLE +q6core@3 { + compatible = "qcom,q6core"; + reg = <APR_SVC_ADSP_CORE>; +}; diff --git a/Documentation/devicetree/bindings/sound/rt274.txt b/Documentation/devicetree/bindings/sound/rt274.txt index e9a6178c78cf..791a1bd767b9 100644 --- a/Documentation/devicetree/bindings/sound/rt274.txt +++ b/Documentation/devicetree/bindings/sound/rt274.txt @@ -26,7 +26,7 @@ Pins on the device (for linking into audio routes) for RT274: Example: -codec: rt274@1c { +rt274: codec@1c { compatible = "realtek,rt274"; reg = <0x1c>; interrupts = <7 IRQ_TYPE_EDGE_FALLING>; diff --git a/Documentation/devicetree/bindings/sound/rt5514.txt b/Documentation/devicetree/bindings/sound/rt5514.txt index 4f33b0d96afe..b25ed08c7a5a 100644 --- a/Documentation/devicetree/bindings/sound/rt5514.txt +++ b/Documentation/devicetree/bindings/sound/rt5514.txt @@ -32,7 +32,7 @@ Pins on the device (for linking into audio routes) for I2C: Example: -codec: rt5514@57 { +rt5514: codec@57 { compatible = "realtek,rt5514"; reg = <0x57>; }; diff --git a/Documentation/devicetree/bindings/sound/rt5616.txt b/Documentation/devicetree/bindings/sound/rt5616.txt index e41085818559..540a4bf252e4 100644 --- a/Documentation/devicetree/bindings/sound/rt5616.txt +++ b/Documentation/devicetree/bindings/sound/rt5616.txt @@ -26,7 +26,7 @@ Pins on the device (for linking into audio routes) for RT5616: Example: -codec: rt5616@1b { +rt5616: codec@1b { compatible = "realtek,rt5616"; reg = <0x1b>; }; diff --git a/Documentation/devicetree/bindings/sound/rt5640.txt b/Documentation/devicetree/bindings/sound/rt5640.txt index 57fe64643050..e40e4893eed8 100644 --- a/Documentation/devicetree/bindings/sound/rt5640.txt +++ b/Documentation/devicetree/bindings/sound/rt5640.txt @@ -22,6 +22,41 @@ Optional properties: - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin. +- realtek,dmic1-data-pin + 0: dmic1 is not used + 1: using IN1P pin as dmic1 data pin + 2: using GPIO3 pin as dmic1 data pin + +- realtek,dmic2-data-pin + 0: dmic2 is not used + 1: using IN1N pin as dmic2 data pin + 2: using GPIO4 pin as dmic2 data pin + +- realtek,jack-detect-source + u32. Valid values: + 0: jack-detect is not used + 1: Use GPIO1 for jack-detect + 2: Use JD1_IN4P for jack-detect + 3: Use JD2_IN4N for jack-detect + 4: Use GPIO2 for jack-detect + 5: Use GPIO3 for jack-detect + 6: Use GPIO4 for jack-detect + +- realtek,jack-detect-not-inverted + bool. Normal jack-detect switches give an inverted signal, set this bool + in the rare case you've a jack-detect switch which is not inverted. + +- realtek,over-current-threshold-microamp + u32, micbias over-current detection threshold in µA, valid values are + 600, 1500 and 2000µA. + +- realtek,over-current-scale-factor + u32, micbias over-current detection scale-factor, valid values are: + 0: Scale current by 0.5 + 1: Scale current by 0.75 + 2: Scale current by 1.0 + 3: Scale current by 1.5 + Pins on the device (for linking into audio routes) for RT5639/RT5640: * DMIC1 diff --git a/Documentation/devicetree/bindings/sound/rt5645.txt b/Documentation/devicetree/bindings/sound/rt5645.txt index 7cee1f518f59..a03f9a872a71 100644 --- a/Documentation/devicetree/bindings/sound/rt5645.txt +++ b/Documentation/devicetree/bindings/sound/rt5645.txt @@ -69,4 +69,4 @@ codec: rt5650@1a { realtek,dmic-en = "true"; realtek,en-jd-func = "true"; realtek,jd-mode = <3>; -};
\ No newline at end of file +}; diff --git a/Documentation/devicetree/bindings/sound/rt5651.txt b/Documentation/devicetree/bindings/sound/rt5651.txt index b85221864cec..a41199a5cd79 100644 --- a/Documentation/devicetree/bindings/sound/rt5651.txt +++ b/Documentation/devicetree/bindings/sound/rt5651.txt @@ -50,7 +50,7 @@ Pins on the device (for linking into audio routes) for RT5651: Example: -codec: rt5651@1a { +rt5651: codec@1a { compatible = "realtek,rt5651"; reg = <0x1a>; realtek,dmic-en = "true"; diff --git a/Documentation/devicetree/bindings/sound/rt5663.txt b/Documentation/devicetree/bindings/sound/rt5663.txt index 497bcfc58b71..23386446c63d 100644 --- a/Documentation/devicetree/bindings/sound/rt5663.txt +++ b/Documentation/devicetree/bindings/sound/rt5663.txt @@ -47,7 +47,7 @@ Pins on the device (for linking into audio routes) for RT5663: Example: -codec: rt5663@12 { +rt5663: codec@12 { compatible = "realtek,rt5663"; reg = <0x12>; interrupts = <7 IRQ_TYPE_EDGE_FALLING>; diff --git a/Documentation/devicetree/bindings/sound/rt5668.txt b/Documentation/devicetree/bindings/sound/rt5668.txt new file mode 100644 index 000000000000..c88b96e7764b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5668.txt @@ -0,0 +1,50 @@ +RT5668B audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : "realtek,rt5668b" + +- reg : The I2C address of the device. + +Optional properties: + +- interrupts : The CODEC's interrupt output. + +- realtek,dmic1-data-pin + 0: dmic1 is not used + 1: using GPIO2 pin as dmic1 data pin + 2: using GPIO5 pin as dmic1 data pin + +- realtek,dmic1-clk-pin + 0: using GPIO1 pin as dmic1 clock pin + 1: using GPIO3 pin as dmic1 clock pin + +- realtek,jd-src + 0: No JD is used + 1: using JD1 as JD source + +- realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin. + +Pins on the device (for linking into audio routes) for RT5668B: + + * DMIC L1 + * DMIC R1 + * IN1P + * HPOL + * HPOR + +Example: + +rt5668 { + compatible = "realtek,rt5668b"; + reg = <0x1a>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(U, 6) GPIO_ACTIVE_HIGH>; + realtek,ldo1-en-gpios = + <&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_HIGH>; + realtek,dmic1-data-pin = <1>; + realtek,dmic1-clk-pin = <1>; + realtek,jd-src = <1>; +}; diff --git a/Documentation/devicetree/bindings/sound/sgtl5000.txt b/Documentation/devicetree/bindings/sound/sgtl5000.txt index 9a36c7e2a143..0f214457476f 100644 --- a/Documentation/devicetree/bindings/sound/sgtl5000.txt +++ b/Documentation/devicetree/bindings/sound/sgtl5000.txt @@ -39,7 +39,7 @@ VDDIO 1.8V 2.5V 3.3V Example: -codec: sgtl5000@a { +sgtl5000: codec@a { compatible = "fsl,sgtl5000"; reg = <0x0a>; #sound-dai-cells = <0>; diff --git a/Documentation/devicetree/bindings/sound/simple-card.txt b/Documentation/devicetree/bindings/sound/simple-card.txt index 17c13e74667d..a4c72d09cd45 100644 --- a/Documentation/devicetree/bindings/sound/simple-card.txt +++ b/Documentation/devicetree/bindings/sound/simple-card.txt @@ -86,6 +86,11 @@ Optional CPU/CODEC subnodes properties: in dai startup() and disabled with clk_disable_unprepare() in dai shutdown(). + If a clock is specified and a + multiplication factor is given with + mclk-fs, the clock will be set to the + calculated mclk frequency when the + stream starts. - system-clock-direction-out : specifies clock direction as 'out' on initialization. It is useful for some aCPUs with fixed clocks. diff --git a/Documentation/devicetree/bindings/sound/ti,tas6424.txt b/Documentation/devicetree/bindings/sound/ti,tas6424.txt index 1c4ada0eef4e..eacb54f34188 100644 --- a/Documentation/devicetree/bindings/sound/ti,tas6424.txt +++ b/Documentation/devicetree/bindings/sound/ti,tas6424.txt @@ -6,6 +6,8 @@ Required properties: - compatible: "ti,tas6424" - TAS6424 - reg: I2C slave address - sound-dai-cells: must be equal to 0 + - standby-gpios: GPIO used to shut the TAS6424 down. + - mute-gpios: GPIO used to mute all the outputs Example: diff --git a/Documentation/devicetree/bindings/sound/tscs42xx.txt b/Documentation/devicetree/bindings/sound/tscs42xx.txt index 2ac2f0996697..7eea32e9d078 100644 --- a/Documentation/devicetree/bindings/sound/tscs42xx.txt +++ b/Documentation/devicetree/bindings/sound/tscs42xx.txt @@ -8,9 +8,15 @@ Required Properties: - reg : <0x71> for analog mic <0x69> for digital mic + - clock-names: Must one of the following "mclk1", "xtal", "mclk2" + + - clocks: phandle of the clock that provides the codec sysclk + Example: wookie: codec@69 { compatible = "tempo,tscs42A2"; reg = <0x69>; + clock-names = "xtal"; + clocks = <&audio_xtal>; }; diff --git a/Documentation/devicetree/bindings/sound/tscs454.txt b/Documentation/devicetree/bindings/sound/tscs454.txt new file mode 100644 index 000000000000..3ba3e2d2c206 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tscs454.txt @@ -0,0 +1,23 @@ +TSCS454 Audio CODEC + +Required Properties: + + - compatible : "tempo,tscs454" + + - reg : <0x69> + + - clock-names: Must one of the following "xtal", "mclk1", "mclk2" + + - clocks: phandle of the clock that provides the codec sysclk + + Note: If clock is not provided then bit clock is assumed + +Example: + +redwood: codec@69 { + #sound-dai-cells = <1>; + compatible = "tempo,tscs454"; + reg = <0x69>; + clock-names = "mclk1"; + clocks = <&audio_mclk>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8510.txt b/Documentation/devicetree/bindings/sound/wm8510.txt index fa1a32b85577..e6b6cc041f89 100644 --- a/Documentation/devicetree/bindings/sound/wm8510.txt +++ b/Documentation/devicetree/bindings/sound/wm8510.txt @@ -12,7 +12,7 @@ Required properties: Example: -codec: wm8510@1a { +wm8510: codec@1a { compatible = "wlf,wm8510"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8523.txt b/Documentation/devicetree/bindings/sound/wm8523.txt index 04746186b283..f3a6485f4b8a 100644 --- a/Documentation/devicetree/bindings/sound/wm8523.txt +++ b/Documentation/devicetree/bindings/sound/wm8523.txt @@ -10,7 +10,7 @@ Required properties: Example: -codec: wm8523@1a { +wm8523: codec@1a { compatible = "wlf,wm8523"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8524.txt b/Documentation/devicetree/bindings/sound/wm8524.txt index 0f0553563fc1..f6c0c263b135 100644 --- a/Documentation/devicetree/bindings/sound/wm8524.txt +++ b/Documentation/devicetree/bindings/sound/wm8524.txt @@ -10,7 +10,7 @@ Required properties: Example: -codec: wm8524 { +wm8524: codec { compatible = "wlf,wm8524"; wlf,mute-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8580.txt b/Documentation/devicetree/bindings/sound/wm8580.txt index 78fce9b14954..ff3f9f5f2111 100644 --- a/Documentation/devicetree/bindings/sound/wm8580.txt +++ b/Documentation/devicetree/bindings/sound/wm8580.txt @@ -10,7 +10,7 @@ Required properties: Example: -codec: wm8580@1a { +wm8580: codec@1a { compatible = "wlf,wm8580"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8711.txt b/Documentation/devicetree/bindings/sound/wm8711.txt index 8ed9998cd23c..c30a1387c4bf 100644 --- a/Documentation/devicetree/bindings/sound/wm8711.txt +++ b/Documentation/devicetree/bindings/sound/wm8711.txt @@ -12,7 +12,7 @@ Required properties: Example: -codec: wm8711@1a { +wm8711: codec@1a { compatible = "wlf,wm8711"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8728.txt b/Documentation/devicetree/bindings/sound/wm8728.txt index a8b5c3668e60..a3608b4c78b9 100644 --- a/Documentation/devicetree/bindings/sound/wm8728.txt +++ b/Documentation/devicetree/bindings/sound/wm8728.txt @@ -12,7 +12,7 @@ Required properties: Example: -codec: wm8728@1a { +wm8728: codec@1a { compatible = "wlf,wm8728"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8731.txt b/Documentation/devicetree/bindings/sound/wm8731.txt index 236690e99b87..f660d9bb0e69 100644 --- a/Documentation/devicetree/bindings/sound/wm8731.txt +++ b/Documentation/devicetree/bindings/sound/wm8731.txt @@ -12,7 +12,7 @@ Required properties: Example: -codec: wm8731@1a { +wm8731: codec@1a { compatible = "wlf,wm8731"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8737.txt b/Documentation/devicetree/bindings/sound/wm8737.txt index 4bc2cea3b140..eda1ec6a7563 100644 --- a/Documentation/devicetree/bindings/sound/wm8737.txt +++ b/Documentation/devicetree/bindings/sound/wm8737.txt @@ -12,7 +12,7 @@ Required properties: Example: -codec: wm8737@1a { +wm8737: codec@1a { compatible = "wlf,wm8737"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8741.txt b/Documentation/devicetree/bindings/sound/wm8741.txt index a13315408719..b69e196c741c 100644 --- a/Documentation/devicetree/bindings/sound/wm8741.txt +++ b/Documentation/devicetree/bindings/sound/wm8741.txt @@ -21,7 +21,7 @@ Optional properties: Example: -codec: wm8741@1a { +wm8741: codec@1a { compatible = "wlf,wm8741"; reg = <0x1a>; diff --git a/Documentation/devicetree/bindings/sound/wm8750.txt b/Documentation/devicetree/bindings/sound/wm8750.txt index 8db239fd5ecd..682f221f6f38 100644 --- a/Documentation/devicetree/bindings/sound/wm8750.txt +++ b/Documentation/devicetree/bindings/sound/wm8750.txt @@ -12,7 +12,7 @@ Required properties: Example: -codec: wm8750@1a { +wm8750: codec@1a { compatible = "wlf,wm8750"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8753.txt b/Documentation/devicetree/bindings/sound/wm8753.txt index 8eee61282105..eca9e5a825a9 100644 --- a/Documentation/devicetree/bindings/sound/wm8753.txt +++ b/Documentation/devicetree/bindings/sound/wm8753.txt @@ -34,7 +34,7 @@ Pins on the device (for linking into audio routes): Example: -codec: wm8753@1a { +wm8753: codec@1a { compatible = "wlf,wm8753"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8770.txt b/Documentation/devicetree/bindings/sound/wm8770.txt index 866e00ca150b..cac762a1105d 100644 --- a/Documentation/devicetree/bindings/sound/wm8770.txt +++ b/Documentation/devicetree/bindings/sound/wm8770.txt @@ -10,7 +10,7 @@ Required properties: Example: -codec: wm8770@1 { +wm8770: codec@1 { compatible = "wlf,wm8770"; reg = <1>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8776.txt b/Documentation/devicetree/bindings/sound/wm8776.txt index 3b9ca49abc2b..01173369c3ed 100644 --- a/Documentation/devicetree/bindings/sound/wm8776.txt +++ b/Documentation/devicetree/bindings/sound/wm8776.txt @@ -12,7 +12,7 @@ Required properties: Example: -codec: wm8776@1a { +wm8776: codec@1a { compatible = "wlf,wm8776"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8804.txt b/Documentation/devicetree/bindings/sound/wm8804.txt index 6fd124b16496..2c1641c17a91 100644 --- a/Documentation/devicetree/bindings/sound/wm8804.txt +++ b/Documentation/devicetree/bindings/sound/wm8804.txt @@ -19,7 +19,7 @@ Optional properties: Example: -codec: wm8804@1a { +wm8804: codec@1a { compatible = "wlf,wm8804"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/wm8903.txt b/Documentation/devicetree/bindings/sound/wm8903.txt index afc51caf1137..6371c2434afe 100644 --- a/Documentation/devicetree/bindings/sound/wm8903.txt +++ b/Documentation/devicetree/bindings/sound/wm8903.txt @@ -57,7 +57,7 @@ Pins on the device (for linking into audio routes): Example: -codec: wm8903@1a { +wm8903: codec@1a { compatible = "wlf,wm8903"; reg = <0x1a>; interrupts = < 347 >; diff --git a/Documentation/devicetree/bindings/sound/wm8960.txt b/Documentation/devicetree/bindings/sound/wm8960.txt index 2deb8a3da9c5..6d29ac3750ee 100644 --- a/Documentation/devicetree/bindings/sound/wm8960.txt +++ b/Documentation/devicetree/bindings/sound/wm8960.txt @@ -23,7 +23,7 @@ Optional properties: Example: -codec: wm8960@1a { +wm8960: codec@1a { compatible = "wlf,wm8960"; reg = <0x1a>; diff --git a/Documentation/devicetree/bindings/sound/wm8962.txt b/Documentation/devicetree/bindings/sound/wm8962.txt index 7f82b59ec8f9..dcfa9a3369fd 100644 --- a/Documentation/devicetree/bindings/sound/wm8962.txt +++ b/Documentation/devicetree/bindings/sound/wm8962.txt @@ -24,7 +24,7 @@ Optional properties: Example: -codec: wm8962@1a { +wm8962: codec@1a { compatible = "wlf,wm8962"; reg = <0x1a>; diff --git a/Documentation/devicetree/bindings/sound/wm8994.txt b/Documentation/devicetree/bindings/sound/wm8994.txt index 68c4e8d96bed..4a9dead1b7d3 100644 --- a/Documentation/devicetree/bindings/sound/wm8994.txt +++ b/Documentation/devicetree/bindings/sound/wm8994.txt @@ -59,7 +59,7 @@ Optional properties: Example: -codec: wm8994@1a { +wm8994: codec@1a { compatible = "wlf,wm8994"; reg = <0x1a>; diff --git a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt index 1b596fd38dc4..b957acff57aa 100644 --- a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt @@ -49,19 +49,6 @@ on the SoC (only first trip points defined in DT will be configured): - samsung,exynos5433-tmu: 8 - samsung,exynos7-tmu: 8 -Following properties are mandatory (depending on SoC): -- samsung,tmu_gain: Gain value for internal TMU operation. -- samsung,tmu_reference_voltage: Value of TMU IP block's reference voltage -- samsung,tmu_noise_cancel_mode: Mode for noise cancellation -- samsung,tmu_efuse_value: Default level of temperature - it is needed when - in factory fusing produced wrong value -- samsung,tmu_min_efuse_value: Minimum temperature fused value -- samsung,tmu_max_efuse_value: Maximum temperature fused value -- samsung,tmu_first_point_trim: First point trimming value -- samsung,tmu_second_point_trim: Second point trimming value -- samsung,tmu_default_temp_offset: Default temperature offset -- samsung,tmu_cal_type: Callibration type - ** Optional properties: - vtmu-supply: This entry is optional and provides the regulator node supplying @@ -78,7 +65,7 @@ Example 1): clocks = <&clock 383>; clock-names = "tmu_apbif"; vtmu-supply = <&tmu_regulator_node>; - #include "exynos4412-tmu-sensor-conf.dtsi" + #thermal-sensor-cells = <0>; }; Example 2): @@ -89,7 +76,7 @@ Example 2): interrupts = <0 58 0>; clocks = <&clock 21>; clock-names = "tmu_apbif"; - #include "exynos5440-tmu-sensor-conf.dtsi" + #thermal-sensor-cells = <0>; }; Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register") @@ -99,7 +86,7 @@ Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register") interrupts = <0 184 0>; clocks = <&clock 318>, <&clock 318>; clock-names = "tmu_apbif", "tmu_triminfo_apbif"; - #include "exynos4412-tmu-sensor-conf.dtsi" + #thermal-sensor-cells = <0>; }; tmu_cpu3: tmu@1006c000 { @@ -108,7 +95,7 @@ Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register") interrupts = <0 185 0>; clocks = <&clock 318>, <&clock 319>; clock-names = "tmu_apbif", "tmu_triminfo_apbif"; - #include "exynos4412-tmu-sensor-conf.dtsi" + #thermal-sensor-cells = <0>; }; tmu_gpu: tmu@100a0000 { @@ -117,7 +104,7 @@ Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register") interrupts = <0 215 0>; clocks = <&clock 319>, <&clock 318>; clock-names = "tmu_apbif", "tmu_triminfo_apbif"; - #include "exynos4412-tmu-sensor-conf.dtsi" + #thermal-sensor-cells = <0>; }; Note: For multi-instance tmu each instance should have an alias correctly diff --git a/Documentation/devicetree/bindings/thermal/thermal.txt b/Documentation/devicetree/bindings/thermal/thermal.txt index 1719d47a5e2f..cc553f0952c5 100644 --- a/Documentation/devicetree/bindings/thermal/thermal.txt +++ b/Documentation/devicetree/bindings/thermal/thermal.txt @@ -55,8 +55,7 @@ of heat dissipation). For example a fan's cooling states correspond to the different fan speeds possible. Cooling states are referred to by single unsigned integers, where larger numbers mean greater heat dissipation. The precise set of cooling states associated with a device -(as referred to by the cooling-min-level and cooling-max-level -properties) should be defined in a particular device's binding. +should be defined in a particular device's binding. For more examples of cooling devices, refer to the example sections below. Required properties: @@ -69,15 +68,6 @@ Required properties: See Cooling device maps section below for more details on how consumers refer to cooling devices. -Optional properties: -- cooling-min-level: An integer indicating the smallest - Type: unsigned cooling state accepted. Typically 0. - Size: one cell - -- cooling-max-level: An integer indicating the largest - Type: unsigned cooling state accepted. - Size: one cell - * Trip points The trip node is a node to describe a point in the temperature domain @@ -226,8 +216,6 @@ cpus { 396000 950000 198000 850000 >; - cooling-min-level = <0>; - cooling-max-level = <3>; #cooling-cells = <2>; /* min followed by max */ }; ... @@ -241,8 +229,6 @@ cpus { */ fan0: fan@48 { ... - cooling-min-level = <0>; - cooling-max-level = <9>; #cooling-cells = <2>; /* min followed by max */ }; }; diff --git a/Documentation/devicetree/bindings/timer/nuvoton,npcm7xx-timer.txt b/Documentation/devicetree/bindings/timer/nuvoton,npcm7xx-timer.txt new file mode 100644 index 000000000000..ea22dfe485be --- /dev/null +++ b/Documentation/devicetree/bindings/timer/nuvoton,npcm7xx-timer.txt @@ -0,0 +1,21 @@ +Nuvoton NPCM7xx timer + +Nuvoton NPCM7xx have three timer modules, each timer module provides five 24-bit +timer counters. + +Required properties: +- compatible : "nuvoton,npcm750-timer" for Poleg NPCM750. +- reg : Offset and length of the register set for the device. +- interrupts : Contain the timer interrupt with flags for + falling edge. +- clocks : phandle of timer reference clock (usually a 25 MHz clock). + +Example: + +timer@f0008000 { + compatible = "nuvoton,npcm750-timer"; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + reg = <0xf0008000 0x50>; + clocks = <&clk NPCM7XX_CLK_TIMER>; +}; + diff --git a/Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt b/Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt index b4aa7ddb5b13..f82087b220f4 100644 --- a/Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt +++ b/Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt @@ -15,7 +15,7 @@ Required properties: - interrupts : Should be the clock event device interrupt. - clocks : The clocks provided by the SoC to drive the timer, must contain an entry for each entry in clock-names. -- clock-names : Must include the following entries: "igp" and "per". +- clock-names : Must include the following entries: "ipg" and "per". Example: tpm5: tpm@40260000 { diff --git a/Documentation/devicetree/bindings/trivial-devices.txt b/Documentation/devicetree/bindings/trivial-devices.txt index 2e3740f98c41..763a2808a95c 100644 --- a/Documentation/devicetree/bindings/trivial-devices.txt +++ b/Documentation/devicetree/bindings/trivial-devices.txt @@ -75,6 +75,18 @@ maxim,max6621 PECI-to-I2C translator for PECI-to-SMBus/I2C protocol conversion maxim,max6625 9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface mcube,mc3230 mCube 3-axis 8-bit digital accelerometer memsic,mxc6225 MEMSIC 2-axis 8-bit digital accelerometer +microchip,mcp4017-502 Microchip 7-bit Single I2C Digital POT (5k) +microchip,mcp4017-103 Microchip 7-bit Single I2C Digital POT (10k) +microchip,mcp4017-503 Microchip 7-bit Single I2C Digital POT (50k) +microchip,mcp4017-104 Microchip 7-bit Single I2C Digital POT (100k) +microchip,mcp4018-502 Microchip 7-bit Single I2C Digital POT (5k) +microchip,mcp4018-103 Microchip 7-bit Single I2C Digital POT (10k) +microchip,mcp4018-503 Microchip 7-bit Single I2C Digital POT (50k) +microchip,mcp4018-104 Microchip 7-bit Single I2C Digital POT (100k) +microchip,mcp4019-502 Microchip 7-bit Single I2C Digital POT (5k) +microchip,mcp4019-103 Microchip 7-bit Single I2C Digital POT (10k) +microchip,mcp4019-503 Microchip 7-bit Single I2C Digital POT (50k) +microchip,mcp4019-104 Microchip 7-bit Single I2C Digital POT (100k) microchip,mcp4531-502 Microchip 7-bit Single I2C Digital Potentiometer (5k) microchip,mcp4531-103 Microchip 7-bit Single I2C Digital Potentiometer (10k) microchip,mcp4531-503 Microchip 7-bit Single I2C Digital Potentiometer (50k) diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index 0e03344e2e8b..2e9318151df7 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -76,6 +76,10 @@ Optional properties: needs to make sure it does not send more than 90% maximum_periodic_data_per_frame. The use case is multiple transactions, but less frame rate. +- mux-controls: The mux control for toggling host/device output of this + controller. It's expected that a mux state of 0 indicates device mode and a + mux state of 1 indicates host mode. +- mux-control-names: Shall be "usb_switch" if mux-controls is specified. i.mx specific properties - fsl,usbmisc: phandler of non-core register device, with one @@ -102,4 +106,6 @@ Example: rx-burst-size-dword = <0x10>; extcon = <0>, <&usb_id>; phy-clkgate-delay-us = <400>; + mux-controls = <&usb_switch>; + mux-control-names = "usb_switch"; }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 0dbd3083e7dd..7f13ebef06cb 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -7,6 +7,26 @@ Required properties: - compatible: must be "snps,dwc3" - reg : Address and length of the register set for the device - interrupts: Interrupts used by the dwc3 controller. + - clock-names: should contain "ref", "bus_early", "suspend" + - clocks: list of phandle and clock specifier pairs corresponding to + entries in the clock-names property. + +Exception for clocks: + clocks are optional if the parent node (i.e. glue-layer) is compatible to + one of the following: + "amlogic,meson-axg-dwc3" + "amlogic,meson-gxl-dwc3" + "cavium,octeon-7130-usb-uctl" + "qcom,dwc3" + "samsung,exynos5250-dwusb3" + "samsung,exynos7-dwusb3" + "sprd,sc9860-dwc3" + "st,stih407-dwc3" + "ti,am437x-dwc3" + "ti,dwc3" + "ti,keystone-dwc3" + "rockchip,rk3399-dwc3" + "xlnx,zynqmp-dwc3" Optional properties: - usb-phy : array of phandle for the PHY device. The first element @@ -15,6 +35,7 @@ Optional properties: - phys: from the *Generic PHY* bindings - phy-names: from the *Generic PHY* bindings; supported names are "usb2-phy" or "usb3-phy". + - resets: a single pair of phandle and reset specifier - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable - snps,disable_scramble_quirk: true when SW should disable data scrambling. Only really useful for FPGA builds. diff --git a/Documentation/devicetree/bindings/usb/fcs,fusb302.txt b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt index 472facfa5a71..6087dc7f209e 100644 --- a/Documentation/devicetree/bindings/usb/fcs,fusb302.txt +++ b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt @@ -6,12 +6,6 @@ Required properties : - interrupts : Interrupt specifier Optional properties : -- fcs,max-sink-microvolt : Maximum voltage to negotiate when configured as sink -- fcs,max-sink-microamp : Maximum current to negotiate when configured as sink -- fcs,max-sink-microwatt : Maximum power to negotiate when configured as sink - If this is less then max-sink-microvolt * - max-sink-microamp then the configured current will - be clamped. - fcs,operating-sink-microwatt : Minimum amount of power accepted from a sink when negotiating diff --git a/Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt b/Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt new file mode 100644 index 000000000000..f4633496b122 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt @@ -0,0 +1,45 @@ +HiSilicon STB xHCI + +The device node for HiSilicon STB xHCI host controller + +Required properties: + - compatible: should be "hisilicon,hi3798cv200-xhci" + - reg: specifies physical base address and size of the registers + - interrupts : interrupt used by the controller + - clocks: a list of phandle + clock-specifier pairs, one for each + entry in clock-names + - clock-names: must contain + "bus": for bus clock + "utmi": for utmi clock + "pipe": for pipe clock + "suspend": for suspend clock + - resets: a list of phandle and reset specifier pairs as listed in + reset-names property. + - reset-names: must contain + "soft": for soft reset + - phys: a list of phandle + phy specifier pairs + - phy-names: must contain at least one of following: + "inno": for inno phy + "combo": for combo phy + +Optional properties: + - usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM + - usb3-lpm-capable: determines if platform is USB3 LPM capable + - imod-interval-ns: default interrupt moderation interval is 40000ns + +Example: + +xhci0: xchi@f98a0000 { + compatible = "hisilicon,hi3798cv200-xhci"; + reg = <0xf98a0000 0x10000>; + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&crg HISTB_USB3_BUS_CLK>, + <&crg HISTB_USB3_UTMI_CLK>, + <&crg HISTB_USB3_PIPE_CLK>, + <&crg HISTB_USB3_SUSPEND_CLK>; + clock-names = "bus", "utmi", "pipe", "suspend"; + resets = <&crg 0xb0 12>; + reset-names = "soft"; + phys = <&usb2_phy1_port1 0>, <&combphy0 PHY_TYPE_USB3>; + phy-names = "inno", "combo"; +}; diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt index bc8a2fa5d2bf..95afdcf3c337 100644 --- a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt +++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt @@ -1,54 +1,95 @@ Qualcomm SuperSpeed DWC3 USB SoC controller Required properties: -- compatible: should contain "qcom,dwc3" +- compatible: Compatible list, contains + "qcom,dwc3" + "qcom,msm8996-dwc3" for msm8996 SOC. + "qcom,sdm845-dwc3" for sdm845 SOC. +- reg: Offset and length of register set for QSCRATCH wrapper +- power-domains: specifies a phandle to PM domain provider node - clocks: A list of phandle + clock-specifier pairs for the clocks listed in clock-names -- clock-names: Should contain the following: +- clock-names: Should contain the following: "core" Master/Core clock, have to be >= 125 MHz for SS operation and >= 60MHz for HS operation + "mock_utmi" Mock utmi clock needed for ITP/SOF generation in + host mode. Its frequency should be 19.2MHz. + "sleep" Sleep clock, used for wakeup when USB3 core goes + into low power mode (U3). Optional clocks: - "iface" System bus AXI clock. Not present on all platforms - "sleep" Sleep clock, used when USB3 core goes into low - power mode (U3). + "iface" System bus AXI clock. + Not present on "qcom,msm8996-dwc3" compatible. + "cfg_noc" System Config NOC clock. + Not present on "qcom,msm8996-dwc3" compatible. +- assigned-clocks: Should be: + MOCK_UTMI_CLK + MASTER_CLK +- assigned-clock-rates: Should be: + 19.2Mhz (192000000) for MOCK_UTMI_CLK + >=125Mhz (125000000) for MASTER_CLK in SS mode + >=60Mhz (60000000) for MASTER_CLK in HS mode + +Optional properties: +- resets: Phandle to reset control that resets core and wrapper. +- interrupts: specifies interrupts from controller wrapper used + to wakeup from low power/susepnd state. Must contain + one or more entry for interrupt-names property +- interrupt-names: Must include the following entries: + - "hs_phy_irq": The interrupt that is asserted when a + wakeup event is received on USB2 bus + - "ss_phy_irq": The interrupt that is asserted when a + wakeup event is received on USB3 bus + - "dm_hs_phy_irq" and "dp_hs_phy_irq": Separate + interrupts for any wakeup event on DM and DP lines +- qcom,select-utmi-as-pipe-clk: if present, disable USB3 pipe_clk requirement. + Used when dwc3 operates without SSPHY and only + HS/FS/LS modes are supported. Required child node: A child node must exist to represent the core DWC3 IP block. The name of the node is not important. The content of the node is defined in dwc3.txt. Phy documentation is provided in the following places: -Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt +Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt - USB3 QMP PHY +Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt - USB2 QUSB2 PHY Example device nodes: hs_phy: phy@100f8800 { - compatible = "qcom,dwc3-hs-usb-phy"; - reg = <0x100f8800 0x30>; - clocks = <&gcc USB30_0_UTMI_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - + compatible = "qcom,qusb2-v2-phy"; + ... }; ss_phy: phy@100f8830 { - compatible = "qcom,dwc3-ss-usb-phy"; - reg = <0x100f8830 0x30>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - + compatible = "qcom,qmp-v3-usb3-phy"; + ... }; - usb3_0: usb30@0 { + usb3_0: usb30@a6f8800 { compatible = "qcom,dwc3"; + reg = <0xa6f8800 0x400>; #address-cells = <1>; #size-cells = <1>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "core"; - ranges; + interrupts = <0 131 0>, <0 486 0>, <0 488 0>, <0 489 0>; + interrupt-names = "hs_phy_irq", "ss_phy_irq", + "dm_hs_phy_irq", "dp_hs_phy_irq"; + + clocks = <&gcc GCC_USB30_PRIM_MASTER_CLK>, + <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_PRIM_SLEEP_CLK>; + clock-names = "core", "mock_utmi", "sleep"; + + assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_PRIM_MASTER_CLK>; + assigned-clock-rates = <19200000>, <133000000>; + + resets = <&gcc GCC_USB30_PRIM_BCR>; + reset-names = "core_reset"; + power-domains = <&gcc USB30_PRIM_GDSC>; + qcom,select-utmi-as-pipe-clk; dwc3@10000000 { compatible = "snps,dwc3"; diff --git a/Documentation/devicetree/bindings/usb/richtek,rt1711h.txt b/Documentation/devicetree/bindings/usb/richtek,rt1711h.txt new file mode 100644 index 000000000000..09e847e92e5e --- /dev/null +++ b/Documentation/devicetree/bindings/usb/richtek,rt1711h.txt @@ -0,0 +1,17 @@ +Richtek RT1711H TypeC PD Controller. + +Required properties: + - compatible : Must be "richtek,rt1711h". + - reg : Must be 0x4e, it's slave address of RT1711H. + - interrupt-parent : the phandle for the interrupt controller that + provides interrupts for this device. + - interrupts : <a b> where a is the interrupt number and b represents an + encoding of the sense and level information for the interrupt. + +Example : +rt1711h@4e { + compatible = "richtek,rt1711h"; + reg = <0x4e>; + interrupt-parent = <&gpio26>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; +}; diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt index c4c00dff4b56..bd1dd316fb23 100644 --- a/Documentation/devicetree/bindings/usb/usb-xhci.txt +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -28,7 +28,10 @@ Required properties: - interrupts: one XHCI interrupt should be described here. Optional properties: - - clocks: reference to a clock + - clocks: reference to the clocks + - clock-names: mandatory if there is a second clock, in this case + the name must be "core" for the first clock and "reg" for the + second one - usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM - usb3-lpm-capable: determines if platform is USB3 LPM capable - quirk-broken-port-ped: set if the controller has broken port disable mechanism diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 12e8b3e576b0..36003832c2a8 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -75,6 +75,7 @@ cnxt Conexant Systems, Inc. compulab CompuLab Ltd. cortina Cortina Systems, Inc. cosmic Cosmic Circuits +crane Crane Connectivity Solutions creative Creative Technology Ltd crystalfontz Crystalfontz America, Inc. cubietech Cubietech, Ltd. @@ -182,6 +183,7 @@ karo Ka-Ro electronics GmbH keithkoep Keith & Koep GmbH keymile Keymile GmbH khadas Khadas +kiebackpeter Kieback & Peter GmbH kinetic Kinetic Technologies kingnovel Kingnovel Technology Co., Ltd. kosagi Sutajio Ko-Usagi PTE Ltd. @@ -225,6 +227,7 @@ motorola Motorola, Inc. moxa Moxa Inc. mpl MPL AG mqmaker mqmaker Inc. +mscc Microsemi Corporation msi Micro-Star International Co. Ltd. mti Imagination Technologies Ltd. (formerly MIPS Technologies Inc.) multi-inno Multi-Inno Technology Co.,Ltd diff --git a/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt b/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt index 107280ef0025..adc6b76fcb3a 100644 --- a/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt @@ -11,6 +11,7 @@ Optional properties: detail please see: Documentation/devicetree/bindings/regmap/regmap.txt. - fsl,ext-reset-output: If present the watchdog device is configured to assert its external reset (WDOG_B) instead of issuing a software reset. +- timeout-sec : Contains the watchdog timeout in seconds Examples: @@ -19,4 +20,5 @@ wdt@73f98000 { reg = <0x73f98000 0x4000>; interrupts = <58>; big-endian; + timeout-sec = <20>; }; diff --git a/Documentation/devicetree/bindings/watchdog/meson-wdt.txt b/Documentation/devicetree/bindings/watchdog/meson-wdt.txt index 8a6d84cb36c9..7588cc3971bf 100644 --- a/Documentation/devicetree/bindings/watchdog/meson-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/meson-wdt.txt @@ -9,9 +9,13 @@ Required properties: "amlogic,meson8m2-wdt" and "amlogic,meson8b-wdt" on Meson8m2 SoCs - reg : Specifies base physical address and size of the registers. +Optional properties: +- timeout-sec: contains the watchdog timeout in seconds. + Example: wdt: watchdog@c1109900 { compatible = "amlogic,meson6-wdt"; reg = <0xc1109900 0x8>; + timeout-sec = <10>; }; diff --git a/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt b/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt index 5b38a30e608c..859dee167b91 100644 --- a/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt @@ -11,9 +11,13 @@ Required properties: - reg : Specifies base physical address and size of the registers. +Optional properties: +- timeout-sec: contains the watchdog timeout in seconds. + Example: wdt: watchdog@10000000 { compatible = "mediatek,mt6589-wdt"; reg = <0x10000000 0x18>; + timeout-sec = <10>; }; diff --git a/Documentation/devicetree/bindings/watchdog/nuvoton,npcm-wdt.txt b/Documentation/devicetree/bindings/watchdog/nuvoton,npcm-wdt.txt new file mode 100644 index 000000000000..6d593003c933 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/nuvoton,npcm-wdt.txt @@ -0,0 +1,28 @@ +Nuvoton NPCM Watchdog + +Nuvoton NPCM timer module provides five 24-bit timer counters, and a watchdog. +The watchdog supports a pre-timeout interrupt that fires 10ms before the +expiry. + +Required properties: +- compatible : "nuvoton,npcm750-wdt" for NPCM750 (Poleg). +- reg : Offset and length of the register set for the device. +- interrupts : Contain the timer interrupt with flags for + falling edge. + +Required clocking property, have to be one of: +- clocks : phandle of timer reference clock. +- clock-frequency : The frequency in Hz of the clock that drives the NPCM7xx + timer (usually 25000000). + +Optional properties: +- timeout-sec : Contains the watchdog timeout in seconds + +Example: + +timer@f000801c { + compatible = "nuvoton,npcm750-wdt"; + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; + reg = <0xf000801c 0x4>; + clocks = <&clk NPCM7XX_CLK_TIMER>; +}; diff --git a/Documentation/devicetree/bindings/watchdog/sirfsoc_wdt.txt b/Documentation/devicetree/bindings/watchdog/sirfsoc_wdt.txt index 9cbc76c89b2b..0dce5e3100b4 100644 --- a/Documentation/devicetree/bindings/watchdog/sirfsoc_wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/sirfsoc_wdt.txt @@ -5,10 +5,14 @@ Required properties: - reg: Address range of tick timer/WDT register set - interrupts: interrupt number to the cpu +Optional properties: +- timeout-sec : Contains the watchdog timeout in seconds + Example: timer@b0020000 { compatible = "sirf,prima2-tick"; reg = <0xb0020000 0x1000>; interrupts = <0>; + timeout-sec = <30>; }; diff --git a/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt b/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt index 62dd5baad70e..ed11ce0ac836 100644 --- a/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt @@ -2,13 +2,19 @@ Allwinner SoCs Watchdog timer Required properties: -- compatible : should be either "allwinner,sun4i-a10-wdt" or - "allwinner,sun6i-a31-wdt" +- compatible : should be one of + "allwinner,sun4i-a10-wdt" + "allwinner,sun6i-a31-wdt" + "allwinner,sun50i-a64-wdt","allwinner,sun6i-a31-wdt" - reg : Specifies base physical address and size of the registers. +Optional properties: +- timeout-sec : Contains the watchdog timeout in seconds + Example: wdt: watchdog@1c20c90 { compatible = "allwinner,sun4i-a10-wdt"; reg = <0x01c20c90 0x10>; + timeout-sec = <10>; }; diff --git a/Documentation/devicetree/overlay-notes.txt b/Documentation/devicetree/overlay-notes.txt index 5175a24d387e..725fb8d255c1 100644 --- a/Documentation/devicetree/overlay-notes.txt +++ b/Documentation/devicetree/overlay-notes.txt @@ -91,13 +91,21 @@ The API is quite easy to use. return value is an error or a cookie identifying this overlay. 2. Call of_overlay_remove() to remove and cleanup the overlay changeset -previously created via the call to of_overlay_apply(). Removal of an overlay -changeset that is stacked by another will not be permitted. +previously created via the call to of_overlay_fdt_apply(). Removal of an +overlay changeset that is stacked by another will not be permitted. Finally, if you need to remove all overlays in one-go, just call of_overlay_remove_all() which will remove every single one in the correct order. +In addition, there is the option to register notifiers that get called on +overlay operations. See of_overlay_notifier_register/unregister and +enum of_overlay_notify_action for details. + +Note that a notifier callback is not supposed to store pointers to a device +tree node or its content beyond OF_OVERLAY_POST_REMOVE corresponding to the +respective node it received. + Overlay DTS Format ------------------ |