diff options
Diffstat (limited to 'Documentation/devicetree')
177 files changed, 4468 insertions, 290 deletions
diff --git a/Documentation/devicetree/bindings/arm/arch_timer.txt b/Documentation/devicetree/bindings/arm/arch_timer.txt index ef5fbe9a77c7..ad440a2b8051 100644 --- a/Documentation/devicetree/bindings/arm/arch_timer.txt +++ b/Documentation/devicetree/bindings/arm/arch_timer.txt @@ -38,6 +38,11 @@ to deliver its interrupts via SPIs. architecturally-defined reset values. Only supported for 32-bit systems which follow the ARMv7 architected reset values. +- arm,no-tick-in-suspend : The main counter does not tick when the system is in + low-power system suspend on some SoCs. This behavior does not match the + Architecture Reference Manual's specification that the system counter "must + be implemented in an always-on power domain." + Example: diff --git a/Documentation/devicetree/bindings/arm/arm-boards b/Documentation/devicetree/bindings/arm/arm-boards index ab318a56fca2..b6e810c2781a 100644 --- a/Documentation/devicetree/bindings/arm/arm-boards +++ b/Documentation/devicetree/bindings/arm/arm-boards @@ -148,11 +148,12 @@ Example: /dts-v1/; #include <dt-bindings/interrupt-controller/irq.h> -#include "skeleton.dtsi" / { model = "ARM RealView PB1176 with device tree"; compatible = "arm,realview-pb1176"; + #address-cells = <1>; + #size-cells = <1>; soc { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/arm/cpu-capacity.txt b/Documentation/devicetree/bindings/arm/cpu-capacity.txt new file mode 100644 index 000000000000..7809fbe0cdb7 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/cpu-capacity.txt @@ -0,0 +1,236 @@ +========================================== +ARM CPUs capacity bindings +========================================== + +========================================== +1 - Introduction +========================================== + +ARM systems may be configured to have cpus with different power/performance +characteristics within the same chip. In this case, additional information has +to be made available to the kernel for it to be aware of such differences and +take decisions accordingly. + +========================================== +2 - CPU capacity definition +========================================== + +CPU capacity is a number that provides the scheduler information about CPUs +heterogeneity. Such heterogeneity can come from micro-architectural differences +(e.g., ARM big.LITTLE systems) or maximum frequency at which CPUs can run +(e.g., SMP systems with multiple frequency domains). Heterogeneity in this +context is about differing performance characteristics; this binding tries to +capture a first-order approximation of the relative performance of CPUs. + +CPU capacities are obtained by running a suitable benchmark. This binding makes +no guarantees on the validity or suitability of any particular benchmark, the +final capacity should, however, be: + +* A "single-threaded" or CPU affine benchmark +* Divided by the running frequency of the CPU executing the benchmark +* Not subject to dynamic frequency scaling of the CPU + +For the time being we however advise usage of the Dhrystone benchmark. What +above thus becomes: + +CPU capacities are obtained by running the Dhrystone benchmark on each CPU at +max frequency (with caches enabled). The obtained DMIPS score is then divided +by the frequency (in MHz) at which the benchmark has been run, so that +DMIPS/MHz are obtained. Such values are then normalized w.r.t. the highest +score obtained in the system. + +========================================== +3 - capacity-dmips-mhz +========================================== + +capacity-dmips-mhz is an optional cpu node [1] property: u32 value +representing CPU capacity expressed in normalized DMIPS/MHz. At boot time, the +maximum frequency available to the cpu is then used to calculate the capacity +value internally used by the kernel. + +capacity-dmips-mhz property is all-or-nothing: if it is specified for a cpu +node, it has to be specified for every other cpu nodes, or the system will +fall back to the default capacity value for every CPU. If cpufreq is not +available, final capacities are calculated by directly using capacity-dmips- +mhz values (normalized w.r.t. the highest value found while parsing the DT). + +=========================================== +4 - Examples +=========================================== + +Example 1 (ARM 64-bit, 6-cpu system, two clusters): +capacities-dmips-mhz are scaled w.r.t. 1024 (cpu@0 and cpu@1) +supposing cluster0@max-freq=1100 and custer1@max-freq=850, +final capacities are 1024 for cluster0 and 446 for cluster1 + +cpus { + #address-cells = <2>; + #size-cells = <0>; + + cpu-map { + cluster0 { + core0 { + cpu = <&A57_0>; + }; + core1 { + cpu = <&A57_1>; + }; + }; + + cluster1 { + core0 { + cpu = <&A53_0>; + }; + core1 { + cpu = <&A53_1>; + }; + core2 { + cpu = <&A53_2>; + }; + core3 { + cpu = <&A53_3>; + }; + }; + }; + + idle-states { + entry-method = "arm,psci"; + + CPU_SLEEP_0: cpu-sleep-0 { + compatible = "arm,idle-state"; + arm,psci-suspend-param = <0x0010000>; + local-timer-stop; + entry-latency-us = <100>; + exit-latency-us = <250>; + min-residency-us = <150>; + }; + + CLUSTER_SLEEP_0: cluster-sleep-0 { + compatible = "arm,idle-state"; + arm,psci-suspend-param = <0x1010000>; + local-timer-stop; + entry-latency-us = <800>; + exit-latency-us = <700>; + min-residency-us = <2500>; + }; + }; + + A57_0: cpu@0 { + compatible = "arm,cortex-a57","arm,armv8"; + reg = <0x0 0x0>; + device_type = "cpu"; + enable-method = "psci"; + next-level-cache = <&A57_L2>; + clocks = <&scpi_dvfs 0>; + cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; + capacity-dmips-mhz = <1024>; + }; + + A57_1: cpu@1 { + compatible = "arm,cortex-a57","arm,armv8"; + reg = <0x0 0x1>; + device_type = "cpu"; + enable-method = "psci"; + next-level-cache = <&A57_L2>; + clocks = <&scpi_dvfs 0>; + cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; + capacity-dmips-mhz = <1024>; + }; + + A53_0: cpu@100 { + compatible = "arm,cortex-a53","arm,armv8"; + reg = <0x0 0x100>; + device_type = "cpu"; + enable-method = "psci"; + next-level-cache = <&A53_L2>; + clocks = <&scpi_dvfs 1>; + cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; + capacity-dmips-mhz = <578>; + }; + + A53_1: cpu@101 { + compatible = "arm,cortex-a53","arm,armv8"; + reg = <0x0 0x101>; + device_type = "cpu"; + enable-method = "psci"; + next-level-cache = <&A53_L2>; + clocks = <&scpi_dvfs 1>; + cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; + capacity-dmips-mhz = <578>; + }; + + A53_2: cpu@102 { + compatible = "arm,cortex-a53","arm,armv8"; + reg = <0x0 0x102>; + device_type = "cpu"; + enable-method = "psci"; + next-level-cache = <&A53_L2>; + clocks = <&scpi_dvfs 1>; + cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; + capacity-dmips-mhz = <578>; + }; + + A53_3: cpu@103 { + compatible = "arm,cortex-a53","arm,armv8"; + reg = <0x0 0x103>; + device_type = "cpu"; + enable-method = "psci"; + next-level-cache = <&A53_L2>; + clocks = <&scpi_dvfs 1>; + cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; + capacity-dmips-mhz = <578>; + }; + + A57_L2: l2-cache0 { + compatible = "cache"; + }; + + A53_L2: l2-cache1 { + compatible = "cache"; + }; +}; + +Example 2 (ARM 32-bit, 4-cpu system, two clusters, + cpus 0,1@1GHz, cpus 2,3@500MHz): +capacities-dmips-mhz are scaled w.r.t. 2 (cpu@0 and cpu@1), this means that first +cpu@0 and cpu@1 are twice fast than cpu@2 and cpu@3 (at the same frequency) + +cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0>; + capacity-dmips-mhz = <2>; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <1>; + capacity-dmips-mhz = <2>; + }; + + cpu2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x100>; + capacity-dmips-mhz = <1>; + }; + + cpu3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x101>; + capacity-dmips-mhz = <1>; + }; +}; + +=========================================== +5 - References +=========================================== + +[1] ARM Linux Kernel documentation - CPUs bindings + Documentation/devicetree/bindings/arm/cpus.txt diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index e6782d50cbcd..c1dcf4cade2e 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -241,6 +241,14 @@ nodes to be present and contain the properties described below. # List of phandles to idle state nodes supported by this cpu [3]. + - capacity-dmips-mhz + Usage: Optional + Value type: <u32> + Definition: + # u32 value representing CPU capacity [3] in + DMIPS/MHz, relative to highest capacity-dmips-mhz + in the system. + - rockchip,pmu Usage: optional for systems that have an "enable-method" property value of "rockchip,rk3066-smp" @@ -464,3 +472,5 @@ cpus { [2] arm/msm/qcom,kpss-acc.txt [3] ARM Linux kernel documentation - idle states bindings Documentation/devicetree/bindings/arm/idle-states.txt +[3] ARM Linux kernel documentation - cpu capacity bindings + Documentation/devicetree/bindings/arm/cpu-capacity.txt diff --git a/Documentation/devicetree/bindings/clock/exynos5433-clock.txt b/Documentation/devicetree/bindings/clock/exynos5433-clock.txt index 63379b04e052..1dc80f8811fe 100644 --- a/Documentation/devicetree/bindings/clock/exynos5433-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5433-clock.txt @@ -79,7 +79,7 @@ Required Properties: Input clocks for fsys clock controller: - oscclk - sclk_ufs_mphy - - div_aclk_fsys_200 + - aclk_fsys_200 - sclk_pcie_100_fsys - sclk_ufsunipro_fsys - sclk_mmc2_fsys @@ -104,6 +104,10 @@ Required Properties: - sclk_decon_tv_vclk_disp - aclk_disp_333 + Input clocks for audio clock controller: + - oscclk + - fout_aud_pll + Input clocks for bus0 clock controller: - aclk_bus0_400 @@ -235,7 +239,7 @@ Example 2: Examples of clock controller nodes are listed below. clock-names = "oscclk", "sclk_ufs_mphy", - "div_aclk_fsys_200", + "aclk_fsys_200", "sclk_pcie_100_fsys", "sclk_ufsunipro_fsys", "sclk_mmc2_fsys", @@ -245,7 +249,7 @@ Example 2: Examples of clock controller nodes are listed below. "sclk_usbdrd30_fsys"; clocks = <&xxti>, <&cmu_cpif CLK_SCLK_UFS_MPHY>, - <&cmu_top CLK_DIV_ACLK_FSYS_200>, + <&cmu_top CLK_ACLK_FSYS_200>, <&cmu_top CLK_SCLK_PCIE_100_FSYS>, <&cmu_top CLK_SCLK_UFSUNIPRO_FSYS>, <&cmu_top CLK_SCLK_MMC2_FSYS>, @@ -297,6 +301,9 @@ Example 2: Examples of clock controller nodes are listed below. compatible = "samsung,exynos5433-cmu-aud"; reg = <0x114c0000 0x0b04>; #clock-cells = <1>; + + clock-names = "oscclk", "fout_aud_pll"; + clocks = <&xxti>, <&cmu_top CLK_FOUT_AUD_PLL>; }; cmu_bus0: clock-controller@13600000 { diff --git a/Documentation/devicetree/bindings/clock/hi3519-crg.txt b/Documentation/devicetree/bindings/clock/hisi-crg.txt index acd1f235d548..cc60b3d423f3 100644 --- a/Documentation/devicetree/bindings/clock/hi3519-crg.txt +++ b/Documentation/devicetree/bindings/clock/hisi-crg.txt @@ -1,7 +1,7 @@ -* Hisilicon Hi3519 Clock and Reset Generator(CRG) +* HiSilicon Clock and Reset Generator(CRG) -The Hi3519 CRG module provides clock and reset signals to various -controllers within the SoC. +The CRG module provides clock and reset signals to various +modules within the SoC. This binding uses the following bindings: Documentation/devicetree/bindings/clock/clock-bindings.txt @@ -10,7 +10,11 @@ This binding uses the following bindings: Required Properties: - compatible: should be one of the following. - - "hisilicon,hi3519-crg" - controller compatible with Hi3519 SoC. + - "hisilicon,hi3516cv300-crg" + - "hisilicon,hi3516cv300-sysctrl" + - "hisilicon,hi3519-crg" + - "hisilicon,hi3798cv200-crg" + - "hisilicon,hi3798cv200-sysctrl" - reg: physical base address of the controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/clock/imx31-clock.txt b/Documentation/devicetree/bindings/clock/imx31-clock.txt index 19df842c694f..8163d565f697 100644 --- a/Documentation/devicetree/bindings/clock/imx31-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx31-clock.txt @@ -77,7 +77,7 @@ Examples: clks: ccm@53f80000{ compatible = "fsl,imx31-ccm"; reg = <0x53f80000 0x4000>; - interrupts = <0 31 0x04 0 53 0x04>; + interrupts = <31>, <53>; #clock-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/clock/oxnas,stdclk.txt b/Documentation/devicetree/bindings/clock/oxnas,stdclk.txt index 208cca6ac4ec..b652f3fb7796 100644 --- a/Documentation/devicetree/bindings/clock/oxnas,stdclk.txt +++ b/Documentation/devicetree/bindings/clock/oxnas,stdclk.txt @@ -5,22 +5,15 @@ Please also refer to clock-bindings.txt in this directory for common clock bindings usage. Required properties: -- compatible: Should be "oxsemi,ox810se-stdclk" +- compatible: For OX810SE, should be "oxsemi,ox810se-stdclk" + For OX820, should be "oxsemi,ox820-stdclk" - #clock-cells: 1, see below Parent node should have the following properties : -- compatible: Should be "oxsemi,ox810se-sys-ctrl", "syscon", "simple-mfd" - -For OX810SE, the clock indices are : - - 0: LEON - - 1: DMA_SGDMA - - 2: CIPHER - - 3: SATA - - 4: AUDIO - - 5: USBMPH - - 6: ETHA - - 7: PCIA - - 8: NAND +- compatible: For OX810SE, should be + "oxsemi,ox810se-sys-ctrl", "syscon", "simple-mfd" + For OX820, should be + "oxsemi,ox820-sys-ctrl", "syscon", "simple-mfd" example: diff --git a/Documentation/devicetree/bindings/clock/qcom,gcc.txt b/Documentation/devicetree/bindings/clock/qcom,gcc.txt index 3cf44217068e..5b4dfc1ea54f 100644 --- a/Documentation/devicetree/bindings/clock/qcom,gcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,gcc.txt @@ -14,6 +14,7 @@ Required properties : "qcom,gcc-msm8974" "qcom,gcc-msm8974pro" "qcom,gcc-msm8974pro-ac" + "qcom,gcc-msm8994" "qcom,gcc-msm8996" "qcom,gcc-mdm9615" diff --git a/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt b/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt new file mode 100644 index 000000000000..87d3714b956a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt @@ -0,0 +1,37 @@ +Qualcomm RPM Clock Controller Binding +------------------------------------------------ +The RPM is a dedicated hardware engine for managing the shared +SoC resources in order to keep the lowest power profile. It +communicates with other hardware subsystems via shared memory +and accepts clock requests, aggregates the requests and turns +the clocks on/off or scales them on demand. + +Required properties : +- compatible : shall contain only one of the following. The generic + compatible "qcom,rpmcc" should be also included. + + "qcom,rpmcc-msm8916", "qcom,rpmcc" + "qcom,rpmcc-apq8064", "qcom,rpmcc" + +- #clock-cells : shall contain 1 + +Example: + smd { + compatible = "qcom,smd"; + + rpm { + interrupts = <0 168 1>; + qcom,ipc = <&apcs 8 0>; + qcom,smd-edge = <15>; + + rpm_requests { + compatible = "qcom,rpm-msm8916"; + qcom,smd-channels = "rpm_requests"; + + rpmcc: clock-controller { + compatible = "qcom,rpmcc-msm8916", "qcom,rpmcc"; + #clock-cells = <1>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt index 394d725ac7e0..c46919412953 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt @@ -13,6 +13,8 @@ They provide the following functionalities: Required Properties: - compatible: Must be one of: + - "renesas,r8a7743-cpg-mssr" for the r8a7743 SoC (RZ/G1M) + - "renesas,r8a7745-cpg-mssr" for the r8a7745 SoC (RZ/G1E) - "renesas,r8a7795-cpg-mssr" for the r8a7795 SoC (R-Car H3) - "renesas,r8a7796-cpg-mssr" for the r8a7796 SoC (R-Car M3-W) @@ -22,8 +24,9 @@ Required Properties: - clocks: References to external parent clocks, one entry for each entry in clock-names - clock-names: List of external parent clock names. Valid names are: - - "extal" (r8a7795, r8a7796) + - "extal" (r8a7743, r8a7745, r8a7795, r8a7796) - "extalr" (r8a7795, r8a7796) + - "usb_extal" (r8a7743, r8a7745) - #clock-cells: Must be 2 - For CPG core clocks, the two clock specifier cells must be "CPG_CORE" diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk1108-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk1108-cru.txt new file mode 100644 index 000000000000..4da126116cf0 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk1108-cru.txt @@ -0,0 +1,59 @@ +* Rockchip RK1108 Clock and Reset Unit + +The RK1108 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk1108-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changeable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk1108-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "ext_vip" - external VIP clock - optional + - "ext_i2s" - external I2S clock - optional + - "ext_gmac" - external GMAC clock - optional + - "hdmiphy" - external clock input derived from HDMI PHY - optional + - "usbphy" - external clock input derived from USB PHY - optional + +Example: Clock controller node: + + cru: cru@20200000 { + compatible = "rockchip,rk1108-cru"; + reg = <0x20200000 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@10230000 { + compatible = "rockchip,rk1108-uart", "snps,dw-apb-uart"; + reg = <0x10230000 0x100>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/st,stm32-rcc.txt b/Documentation/devicetree/bindings/clock/st,stm32-rcc.txt index c209de6cfadb..0532d815dae3 100644 --- a/Documentation/devicetree/bindings/clock/st,stm32-rcc.txt +++ b/Documentation/devicetree/bindings/clock/st,stm32-rcc.txt @@ -7,7 +7,9 @@ Please refer to clock-bindings.txt for common clock controller binding usage. Please also refer to reset.txt for common reset controller binding usage. Required properties: -- compatible: Should be "st,stm32f42xx-rcc" +- compatible: Should be: + "st,stm32f42xx-rcc" + "st,stm32f469-rcc" - reg: should be register base and length as documented in the datasheet - #reset-cells: 1, see below diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt index 3868458a5feb..74d44a4273f2 100644 --- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt +++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt @@ -7,6 +7,7 @@ Required properties : - "allwinner,sun8i-a23-ccu" - "allwinner,sun8i-a33-ccu" - "allwinner,sun8i-h3-ccu" + - "allwinner,sun50i-a64-ccu" - reg: Must contain the registers base address and length - clocks: phandle to the oscillators feeding the CCU. Two are needed: diff --git a/Documentation/devicetree/bindings/clock/uniphier-clock.txt b/Documentation/devicetree/bindings/clock/uniphier-clock.txt index c7179d3b5c33..812163060fa3 100644 --- a/Documentation/devicetree/bindings/clock/uniphier-clock.txt +++ b/Documentation/devicetree/bindings/clock/uniphier-clock.txt @@ -24,7 +24,7 @@ Example: reg = <0x61840000 0x4000>; clock { - compatible = "socionext,uniphier-ld20-clock"; + compatible = "socionext,uniphier-ld11-clock"; #clock-cells = <1>; }; @@ -43,8 +43,8 @@ Provided clocks: 21: USB3 ch1 PHY1 -Media I/O (MIO) clock ---------------------- +Media I/O (MIO) clock, SD clock +------------------------------- Required properties: - compatible: should be one of the following: @@ -52,10 +52,10 @@ Required properties: "socionext,uniphier-ld4-mio-clock" - for LD4 SoC. "socionext,uniphier-pro4-mio-clock" - for Pro4 SoC. "socionext,uniphier-sld8-mio-clock" - for sLD8 SoC. - "socionext,uniphier-pro5-mio-clock" - for Pro5 SoC. - "socionext,uniphier-pxs2-mio-clock" - for PXs2/LD6b SoC. + "socionext,uniphier-pro5-sd-clock" - for Pro5 SoC. + "socionext,uniphier-pxs2-sd-clock" - for PXs2/LD6b SoC. "socionext,uniphier-ld11-mio-clock" - for LD11 SoC. - "socionext,uniphier-ld20-mio-clock" - for LD20 SoC. + "socionext,uniphier-ld20-sd-clock" - for LD20 SoC. - #clock-cells: should be 1. Example: @@ -66,7 +66,7 @@ Example: reg = <0x59810000 0x800>; clock { - compatible = "socionext,uniphier-ld20-mio-clock"; + compatible = "socionext,uniphier-ld11-mio-clock"; #clock-cells = <1>; }; @@ -112,7 +112,7 @@ Example: reg = <0x59820000 0x200>; clock { - compatible = "socionext,uniphier-ld20-peri-clock"; + compatible = "socionext,uniphier-ld11-peri-clock"; #clock-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/cpufreq/brcm,stb-avs-cpu-freq.txt b/Documentation/devicetree/bindings/cpufreq/brcm,stb-avs-cpu-freq.txt new file mode 100644 index 000000000000..af2385795d78 --- /dev/null +++ b/Documentation/devicetree/bindings/cpufreq/brcm,stb-avs-cpu-freq.txt @@ -0,0 +1,78 @@ +Broadcom AVS mail box and interrupt register bindings +===================================================== + +A total of three DT nodes are required. One node (brcm,avs-cpu-data-mem) +references the mailbox register used to communicate with the AVS CPU[1]. The +second node (brcm,avs-cpu-l2-intr) is required to trigger an interrupt on +the AVS CPU. The interrupt tells the AVS CPU that it needs to process a +command sent to it by a driver. Interrupting the AVS CPU is mandatory for +commands to be processed. + +The interface also requires a reference to the AVS host interrupt controller, +so a driver can react to interrupts generated by the AVS CPU whenever a command +has been processed. See [2] for more information on the brcm,l2-intc node. + +[1] The AVS CPU is an independent co-processor that runs proprietary +firmware. On some SoCs, this firmware supports DFS and DVFS in addition to +Adaptive Voltage Scaling. + +[2] Documentation/devicetree/bindings/interrupt-controller/brcm,l2-intc.txt + + +Node brcm,avs-cpu-data-mem +-------------------------- + +Required properties: +- compatible: must include: brcm,avs-cpu-data-mem and + should include: one of brcm,bcm7271-avs-cpu-data-mem or + brcm,bcm7268-avs-cpu-data-mem +- reg: Specifies base physical address and size of the registers. +- interrupts: The interrupt that the AVS CPU will use to interrupt the host + when a command completed. +- interrupt-parent: The interrupt controller the above interrupt is routed + through. +- interrupt-names: The name of the interrupt used to interrupt the host. + +Optional properties: +- None + +Node brcm,avs-cpu-l2-intr +------------------------- + +Required properties: +- compatible: must include: brcm,avs-cpu-l2-intr and + should include: one of brcm,bcm7271-avs-cpu-l2-intr or + brcm,bcm7268-avs-cpu-l2-intr +- reg: Specifies base physical address and size of the registers. + +Optional properties: +- None + + +Example +======= + + avs_host_l2_intc: interrupt-controller@f04d1200 { + #interrupt-cells = <1>; + compatible = "brcm,l2-intc"; + interrupt-parent = <&intc>; + reg = <0xf04d1200 0x48>; + interrupt-controller; + interrupts = <0x0 0x19 0x0>; + interrupt-names = "avs"; + }; + + avs-cpu-data-mem@f04c4000 { + compatible = "brcm,bcm7271-avs-cpu-data-mem", + "brcm,avs-cpu-data-mem"; + reg = <0xf04c4000 0x60>; + interrupts = <0x1a>; + interrupt-parent = <&avs_host_l2_intc>; + interrupt-names = "sw_intr"; + }; + + avs-cpu-l2-intr@f04d1100 { + compatible = "brcm,bcm7271-avs-cpu-l2-intr", + "brcm,avs-cpu-l2-intr"; + reg = <0xf04d1100 0x10>; + }; diff --git a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt index adeca34c5a33..10a425f451fc 100644 --- a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt +++ b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt @@ -123,6 +123,9 @@ PROPERTIES EXAMPLE + +iMX6QDL/SX requires four clocks + crypto@300000 { compatible = "fsl,sec-v4.0"; fsl,sec-era = <2>; @@ -139,6 +142,23 @@ EXAMPLE clock-names = "mem", "aclk", "ipg", "emi_slow"; }; + +iMX6UL does only require three clocks + + crypto: caam@2140000 { + compatible = "fsl,sec-v4.0"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x2140000 0x3c000>; + ranges = <0 0x2140000 0x3c000>; + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&clks IMX6UL_CLK_CAAM_MEM>, + <&clks IMX6UL_CLK_CAAM_ACLK>, + <&clks IMX6UL_CLK_CAAM_IPG>; + clock-names = "mem", "aclk", "ipg"; + }; + ===================================================================== Job Ring (JR) Node diff --git a/Documentation/devicetree/bindings/display/amlogic,meson-vpu.txt b/Documentation/devicetree/bindings/display/amlogic,meson-vpu.txt new file mode 100644 index 000000000000..00f74bad1e95 --- /dev/null +++ b/Documentation/devicetree/bindings/display/amlogic,meson-vpu.txt @@ -0,0 +1,112 @@ +Amlogic Meson Display Controller +================================ + +The Amlogic Meson Display controller is composed of several components +that are going to be documented below: + +DMC|---------------VPU (Video Processing Unit)----------------|------HHI------| + | vd1 _______ _____________ _________________ | | +D |-------| |----| | | | | HDMI PLL | +D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK | +R |-------| |----| Processing | | | | | + | osd2 | | | |---| Enci ----------|----|-----VDAC------| +R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----| +A | osd1 | | | Blenders | | Encl ----------|----|---------------| +M |-------|______|----|____________| |________________| | | +___|__________________________________________________________|_______________| + + +VIU: Video Input Unit +--------------------- + +The Video Input Unit is in charge of the pixel scanout from the DDR memory. +It fetches the frames addresses, stride and parameters from the "Canvas" memory. +This part is also in charge of the CSC (Colorspace Conversion). +It can handle 2 OSD Planes and 2 Video Planes. + +VPP: Video Post Processing +-------------------------- + +The Video Post Processing is in charge of the scaling and blending of the +various planes into a single pixel stream. +There is a special "pre-blending" used by the video planes with a dedicated +scaler and a "post-blending" to merge with the OSD Planes. +The OSD planes also have a dedicated scaler for one of the OSD. + +VENC: Video Encoders +-------------------- + +The VENC is composed of the multiple pixel encoders : + - ENCI : Interlace Video encoder for CVBS and Interlace HDMI + - ENCP : Progressive Video Encoder for HDMI + - ENCL : LCD LVDS Encoder +The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock +tree and provides the scanout clock to the VPP and VIU. +The ENCI is connected to a single VDAC for Composite Output. +The ENCI and ENCP are connected to an on-chip HDMI Transceiver. + +Device Tree Bindings: +--------------------- + +VPU: Video Processing Unit +-------------------------- + +Required properties: +- compatible: value should be different for each SoC family as : + - GXBB (S905) : "amlogic,meson-gxbb-vpu" + - GXL (S905X, S905D) : "amlogic,meson-gxl-vpu" + - GXM (S912) : "amlogic,meson-gxm-vpu" + followed by the common "amlogic,meson-gx-vpu" +- reg: base address and size of he following memory-mapped regions : + - vpu + - hhi + - dmc +- reg-names: should contain the names of the previous memory regions +- interrupts: should contain the VENC Vsync interrupt number + +Required nodes: + +The connections to the VPU output video ports are modeled using the OF graph +bindings specified in Documentation/devicetree/bindings/graph.txt. + +The following table lists for each supported model the port number +corresponding to each VPU output. + + Port 0 Port 1 +----------------------------------------- + S905 (GXBB) CVBS VDAC HDMI-TX + S905X (GXL) CVBS VDAC HDMI-TX + S905D (GXL) CVBS VDAC HDMI-TX + S912 (GXM) CVBS VDAC HDMI-TX + +Example: + +tv-connector { + compatible = "composite-video-connector"; + + port { + tv_connector_in: endpoint { + remote-endpoint = <&cvbs_vdac_out>; + }; + }; +}; + +vpu: vpu@d0100000 { + compatible = "amlogic,meson-gxbb-vpu"; + reg = <0x0 0xd0100000 0x0 0x100000>, + <0x0 0xc883c000 0x0 0x1000>, + <0x0 0xc8838000 0x0 0x1000>; + reg-names = "vpu", "hhi", "dmc"; + interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>; + #address-cells = <1>; + #size-cells = <0>; + + /* CVBS VDAC output port */ + port@0 { + reg = <0>; + + cvbs_vdac_out: endpoint { + remote-endpoint = <&tv_connector_in>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt b/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt index a5ea451e67fc..e2768703ac2b 100644 --- a/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt +++ b/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt @@ -43,6 +43,13 @@ Required properties for DPI: - port: Port node with a single endpoint connecting to the panel device, as defined in [1] +Required properties for VEC: +- compatible: Should be "brcm,bcm2835-vec" +- reg: Physical base address and length of the registers +- clocks: The core clock the unit runs on +- interrupts: The interrupt number + See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt + Required properties for V3D: - compatible: Should be "brcm,bcm2835-v3d" - reg: Physical base address and length of the V3D's registers @@ -92,6 +99,13 @@ dpi: dpi@7e208000 { }; }; +vec: vec@7e806000 { + compatible = "brcm,bcm2835-vec"; + reg = <0x7e806000 0x1000>; + clocks = <&clocks BCM2835_CLOCK_VEC>; + interrupts = <2 27>; +}; + v3d: v3d@7ec00000 { compatible = "brcm,bcm2835-v3d"; reg = <0x7ec00000 0x1000>; diff --git a/Documentation/devicetree/bindings/display/bridge/dumb-vga-dac.txt b/Documentation/devicetree/bindings/display/bridge/dumb-vga-dac.txt index 003bc246a270..164cbb15f04c 100644 --- a/Documentation/devicetree/bindings/display/bridge/dumb-vga-dac.txt +++ b/Documentation/devicetree/bindings/display/bridge/dumb-vga-dac.txt @@ -16,6 +16,8 @@ graph bindings specified in Documentation/devicetree/bindings/graph.txt. - Video port 0 for RGB input - Video port 1 for VGA output +Optional properties: +- vdd-supply: Power supply for DAC Example ------- diff --git a/Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt b/Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt index dc1452f0d5d8..5e9a84d6e5f1 100644 --- a/Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt +++ b/Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt @@ -19,7 +19,9 @@ Required properties: Optional properties - reg-io-width: the width of the reg:1,4, default set to 1 if not present -- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing +- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing, + if the property is omitted, a functionally reduced I2C bus + controller on DW HDMI is probed - clocks, clock-names: phandle to the HDMI CEC clock, name should be "cec" Example: diff --git a/Documentation/devicetree/bindings/display/ti/ti,tfp410.txt b/Documentation/devicetree/bindings/display/bridge/ti,tfp410.txt index 2cbe32a3d0bb..54d7e31525ec 100644 --- a/Documentation/devicetree/bindings/display/ti/ti,tfp410.txt +++ b/Documentation/devicetree/bindings/display/bridge/ti,tfp410.txt @@ -6,10 +6,15 @@ Required properties: Optional properties: - powerdown-gpios: power-down gpio +- reg: I2C address. If and only if present the device node + should be placed into the i2c controller node where the + tfp410 i2c is connected to. Required nodes: -- Video port 0 for DPI input -- Video port 1 for DVI output +- Video port 0 for DPI input [1]. +- Video port 1 for DVI output [1]. + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt Example ------- diff --git a/Documentation/devicetree/bindings/display/ht16k33.txt b/Documentation/devicetree/bindings/display/ht16k33.txt new file mode 100644 index 000000000000..8e5b30b87754 --- /dev/null +++ b/Documentation/devicetree/bindings/display/ht16k33.txt @@ -0,0 +1,42 @@ +Holtek ht16k33 RAM mapping 16*8 LED controller driver with keyscan +------------------------------------------------------------------------------- + +Required properties: +- compatible: "holtek,ht16k33" +- reg: I2C slave address of the chip. +- interrupt-parent: A phandle pointing to the interrupt controller + serving the interrupt for this chip. +- interrupts: Interrupt specification for the key pressed interrupt. +- refresh-rate-hz: Display update interval in HZ. +- debounce-delay-ms: Debouncing interval time in milliseconds. +- linux,keymap: The keymap for keys as described in the binding + document (devicetree/bindings/input/matrix-keymap.txt). + +Optional properties: +- linux,no-autorepeat: Disable keyrepeat. +- default-brightness-level: Initial brightness level [0-15] (default: 15). + +Example: + +&i2c1 { + ht16k33: ht16k33@70 { + compatible = "holtek,ht16k33"; + reg = <0x70>; + refresh-rate-hz = <20>; + debounce-delay-ms = <50>; + interrupt-parent = <&gpio4>; + interrupts = <5 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>; + linux,keymap = < + MATRIX_KEY(2, 0, KEY_F6) + MATRIX_KEY(3, 0, KEY_F8) + MATRIX_KEY(4, 0, KEY_F10) + MATRIX_KEY(5, 0, KEY_F4) + MATRIX_KEY(6, 0, KEY_F2) + MATRIX_KEY(2, 1, KEY_F5) + MATRIX_KEY(3, 1, KEY_F7) + MATRIX_KEY(4, 1, KEY_F9) + MATRIX_KEY(5, 1, KEY_F3) + MATRIX_KEY(6, 1, KEY_F1) + >; + }; +}; diff --git a/Documentation/devicetree/bindings/display/mxsfb.txt b/Documentation/devicetree/bindings/display/mxsfb.txt index 96ec5179c8a0..472e1ea6c591 100644 --- a/Documentation/devicetree/bindings/display/mxsfb.txt +++ b/Documentation/devicetree/bindings/display/mxsfb.txt @@ -1,20 +1,57 @@ * Freescale MXS LCD Interface (LCDIF) +New bindings: +============= Required properties: -- compatible: Should be "fsl,<chip>-lcdif". Supported chips include - imx23 and imx28. -- reg: Address and length of the register set for lcdif -- interrupts: Should contain lcdif interrupts -- display : phandle to display node (see below for details) +- compatible: Should be "fsl,imx23-lcdif" for i.MX23. + Should be "fsl,imx28-lcdif" for i.MX28. + Should be "fsl,imx6sx-lcdif" for i.MX6SX. +- reg: Address and length of the register set for LCDIF +- interrupts: Should contain LCDIF interrupt +- clocks: A list of phandle + clock-specifier pairs, one for each + entry in 'clock-names'. +- clock-names: A list of clock names. For MXSFB it should contain: + - "pix" for the LCDIF block clock + - (MX6SX-only) "axi", "disp_axi" for the bus interface clock + +Required sub-nodes: + - port: The connection to an encoder chip. + +Example: + + lcdif1: display-controller@2220000 { + compatible = "fsl,imx6sx-lcdif", "fsl,imx28-lcdif"; + reg = <0x02220000 0x4000>; + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6SX_CLK_LCDIF1_PIX>, + <&clks IMX6SX_CLK_LCDIF_APB>, + <&clks IMX6SX_CLK_DISPLAY_AXI>; + clock-names = "pix", "axi", "disp_axi"; + + port { + parallel_out: endpoint { + remote-endpoint = <&panel_in_parallel>; + }; + }; + }; + +Deprecated bindings: +==================== +Required properties: +- compatible: Should be "fsl,imx23-lcdif" for i.MX23. + Should be "fsl,imx28-lcdif" for i.MX28. +- reg: Address and length of the register set for LCDIF +- interrupts: Should contain LCDIF interrupts +- display: phandle to display node (see below for details) * display node Required properties: -- bits-per-pixel : <16> for RGB565, <32> for RGB888/666. -- bus-width : number of data lines. Could be <8>, <16>, <18> or <24>. +- bits-per-pixel: <16> for RGB565, <32> for RGB888/666. +- bus-width: number of data lines. Could be <8>, <16>, <18> or <24>. Required sub-node: -- display-timings : Refer to binding doc display-timing.txt for details. +- display-timings: Refer to binding doc display-timing.txt for details. Examples: diff --git a/Documentation/devicetree/bindings/display/panel/auo,g133han01.txt b/Documentation/devicetree/bindings/display/panel/auo,g133han01.txt new file mode 100644 index 000000000000..3afc76747824 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/auo,g133han01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 13.3" FHD (1920x1080) TFT LCD panel + +Required properties: +- compatible: should be "auo,g133han01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/auo,g185han01.txt b/Documentation/devicetree/bindings/display/panel/auo,g185han01.txt new file mode 100644 index 000000000000..ed657c2141d4 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/auo,g185han01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 18.5" FHD (1920x1080) TFT LCD panel + +Required properties: +- compatible: should be "auo,g185han01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/auo,t215hvn01.txt b/Documentation/devicetree/bindings/display/panel/auo,t215hvn01.txt new file mode 100644 index 000000000000..cbd9da3f03b1 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/auo,t215hvn01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 21.5" FHD (1920x1080) color TFT LCD panel + +Required properties: +- compatible: should be "auo,t215hvn01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/chunghwa,claa070wp03xg.txt b/Documentation/devicetree/bindings/display/panel/chunghwa,claa070wp03xg.txt new file mode 100644 index 000000000000..dd22685d2adc --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/chunghwa,claa070wp03xg.txt @@ -0,0 +1,7 @@ +Chunghwa Picture Tubes Ltd. 7" WXGA TFT LCD panel + +Required properties: +- compatible: should be "chunghwa,claa070wp03xg" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/display-timing.txt b/Documentation/devicetree/bindings/display/panel/display-timing.txt index e1d4a0b59612..81a75893d1b8 100644 --- a/Documentation/devicetree/bindings/display/panel/display-timing.txt +++ b/Documentation/devicetree/bindings/display/panel/display-timing.txt @@ -32,6 +32,14 @@ optional properties: - active low = drive pixel data on falling edge/ sample data on rising edge - ignored = ignored + - syncclk-active: with + - active high = drive sync on rising edge/ + sample sync on falling edge of pixel + clock + - active low = drive sync on falling edge/ + sample sync on rising edge of pixel + clock + - omitted = same configuration as pixelclk-active - interlaced (bool): boolean to enable interlaced mode - doublescan (bool): boolean to enable doublescan mode - doubleclk (bool): boolean to enable doubleclock mode diff --git a/Documentation/devicetree/bindings/display/panel/nvd,9128.txt b/Documentation/devicetree/bindings/display/panel/nvd,9128.txt new file mode 100644 index 000000000000..17bcd017c678 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/nvd,9128.txt @@ -0,0 +1,7 @@ +New Vision Display 7.0" 800 RGB x 480 TFT LCD panel + +Required properties: +- compatible: should be "nvd,9128" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/sharp,lq150x1lg11.txt b/Documentation/devicetree/bindings/display/panel/sharp,lq150x1lg11.txt new file mode 100644 index 000000000000..0f57c3143506 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sharp,lq150x1lg11.txt @@ -0,0 +1,36 @@ +Sharp 15" LQ150X1LG11 XGA TFT LCD panel + +Required properties: +- compatible: should be "sharp,lq150x1lg11" +- power-supply: regulator to provide the VCC supply voltage (3.3 volts) + +Optional properties: +- backlight: phandle of the backlight device +- rlud-gpios: a single GPIO for the RL/UD (rotate 180 degrees) pin. +- sellvds-gpios: a single GPIO for the SELLVDS pin. + +If rlud-gpios and/or sellvds-gpios are not specified, the RL/UD and/or SELLVDS +pins are assumed to be handled appropriately by the hardware. + +Example: + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 100000>; /* VBR */ + + brightness-levels = <0 20 40 60 80 100>; + default-brightness-level = <2>; + + power-supply = <&vdd_12v_reg>; /* VDD */ + enable-gpios = <&gpio 42 GPIO_ACTIVE_HIGH>; /* XSTABY */ + }; + + panel { + compatible = "sharp,lq150x1lg11"; + + power-supply = <&vcc_3v3_reg>; /* VCC */ + + backlight = <&backlight>; + rlud-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; /* RL/UD */ + sellvds-gpios = <&gpio 18 GPIO_ACTIVE_HIGH>; /* SELLVDS */ + }; diff --git a/Documentation/devicetree/bindings/display/renesas,du.txt b/Documentation/devicetree/bindings/display/renesas,du.txt index 0d30e42e40be..1a02f099a0ff 100644 --- a/Documentation/devicetree/bindings/display/renesas,du.txt +++ b/Documentation/devicetree/bindings/display/renesas,du.txt @@ -6,9 +6,11 @@ Required Properties: - "renesas,du-r8a7779" for R8A7779 (R-Car H1) compatible DU - "renesas,du-r8a7790" for R8A7790 (R-Car H2) compatible DU - "renesas,du-r8a7791" for R8A7791 (R-Car M2-W) compatible DU + - "renesas,du-r8a7792" for R8A7792 (R-Car V2H) compatible DU - "renesas,du-r8a7793" for R8A7793 (R-Car M2-N) compatible DU - "renesas,du-r8a7794" for R8A7794 (R-Car E2) compatible DU - "renesas,du-r8a7795" for R8A7795 (R-Car H3) compatible DU + - "renesas,du-r8a7796" for R8A7796 (R-Car M3-W) compatible DU - reg: A list of base address and length of each memory resource, one for each entry in the reg-names property. @@ -25,10 +27,10 @@ Required Properties: - clock-names: Name of the clocks. This property is model-dependent. - R8A7779 uses a single functional clock. The clock doesn't need to be named. - - R8A779[01345] use one functional clock per channel and one clock per LVDS - encoder (if available). The functional clocks must be named "du.x" with - "x" being the channel numerical index. The LVDS clocks must be named - "lvds.x" with "x" being the LVDS encoder numerical index. + - R8A779[0123456] use one functional clock per channel and one clock per + LVDS encoder (if available). The functional clocks must be named "du.x" + with "x" being the channel numerical index. The LVDS clocks must be + named "lvds.x" with "x" being the LVDS encoder numerical index. - In addition to the functional and encoder clocks, all DU versions also support externally supplied pixel clocks. Those clocks are optional. When supplied they must be named "dclkin.x" with "x" being the input @@ -47,9 +49,11 @@ corresponding to each DU output. R8A7779 (H1) DPAD 0 DPAD 1 - - R8A7790 (H2) DPAD LVDS 0 LVDS 1 - R8A7791 (M2-W) DPAD LVDS 0 - - + R8A7792 (V2H) DPAD 0 DPAD 1 - - R8A7793 (M2-N) DPAD LVDS 0 - - R8A7794 (E2) DPAD 0 DPAD 1 - - R8A7795 (H3) DPAD HDMI 0 HDMI 1 LVDS + R8A7796 (M3-W) DPAD HDMI LVDS - Example: R8A7790 (R-Car H2) DU diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt index b95696d748c7..b82c00449468 100644 --- a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt @@ -28,6 +28,8 @@ The TCON acts as a timing controller for RGB, LVDS and TV interfaces. Required properties: - compatible: value must be either: * allwinner,sun5i-a13-tcon + * allwinner,sun6i-a31-tcon + * allwinner,sun6i-a31s-tcon * allwinner,sun8i-a33-tcon - reg: base address and size of memory-mapped region - interrupts: interrupt associated to this IP @@ -50,7 +52,7 @@ Required properties: second the block connected to the TCON channel 1 (usually the TV encoder) -On the A13, there is one more clock required: +On SoCs other than the A33, there is one more clock required: - 'tcon-ch1': The clock driving the TCON channel 1 DRC @@ -64,6 +66,8 @@ adaptive backlight control. Required properties: - compatible: value must be one of: + * allwinner,sun6i-a31-drc + * allwinner,sun6i-a31s-drc * allwinner,sun8i-a33-drc - reg: base address and size of the memory-mapped region. - interrupts: interrupt associated to this IP @@ -87,6 +91,7 @@ system. Required properties: - compatible: value must be one of: * allwinner,sun5i-a13-display-backend + * allwinner,sun6i-a31-display-backend * allwinner,sun8i-a33-display-backend - reg: base address and size of the memory-mapped region. - clocks: phandles to the clocks feeding the frontend and backend @@ -117,6 +122,7 @@ deinterlacing and color space conversion. Required properties: - compatible: value must be one of: * allwinner,sun5i-a13-display-frontend + * allwinner,sun6i-a31-display-frontend * allwinner,sun8i-a33-display-frontend - reg: base address and size of the memory-mapped region. - interrupts: interrupt associated to this IP @@ -142,6 +148,8 @@ extra node. Required properties: - compatible: value must be one of: * allwinner,sun5i-a13-display-engine + * allwinner,sun6i-a31-display-engine + * allwinner,sun6i-a31s-display-engine * allwinner,sun8i-a33-display-engine - allwinner,pipelines: list of phandle to the display engine diff --git a/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt b/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt index a83abd79c55c..6fddb4f4f71a 100644 --- a/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt +++ b/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt @@ -1,7 +1,9 @@ Device-Tree bindings for tilcdc DRM driver Required properties: - - compatible: value should be "ti,am33xx-tilcdc". + - compatible: value should be one of the following: + - "ti,am33xx-tilcdc" for AM335x based boards + - "ti,da850-tilcdc" for DA850/AM18x/OMAP-L138 based boards - interrupts: the interrupt number - reg: base address and size of the LCDC device @@ -51,7 +53,7 @@ Optional nodes: Example: fb: fb@4830e000 { - compatible = "ti,am33xx-tilcdc"; + compatible = "ti,am33xx-tilcdc", "ti,da850-tilcdc"; reg = <0x4830e000 0x1000>; interrupt-parent = <&intc>; interrupts = <36>; diff --git a/Documentation/devicetree/bindings/display/zte,vou.txt b/Documentation/devicetree/bindings/display/zte,vou.txt new file mode 100644 index 000000000000..740e5bd2e4f7 --- /dev/null +++ b/Documentation/devicetree/bindings/display/zte,vou.txt @@ -0,0 +1,84 @@ +ZTE VOU Display Controller + +This is a display controller found on ZTE ZX296718 SoC. It includes multiple +Graphic Layer (GL) and Video Layer (VL), two Mixers/Channels, and a few blocks +handling scaling, color space conversion etc. VOU also integrates the support +for typical output devices, like HDMI, TV Encoder, VGA, and RGB LCD. + +* Master VOU node + +It must be the parent node of all the sub-device nodes. + +Required properties: + - compatible: should be "zte,zx296718-vou" + - #address-cells: should be <1> + - #size-cells: should be <1> + - ranges: list of address translations between VOU and sub-devices + +* VOU DPC device + +Required properties: + - compatible: should be "zte,zx296718-dpc" + - reg: Physical base address and length of DPC register regions, one for each + entry in 'reg-names' + - reg-names: The names of register regions. The following regions are required: + "osd" + "timing_ctrl" + "dtrc" + "vou_ctrl" + "otfppu" + - interrupts: VOU DPC interrupt number to CPU + - clocks: A list of phandle + clock-specifier pairs, one for each entry + in 'clock-names' + - clock-names: A list of clock names. The following clocks are required: + "aclk" + "ppu_wclk" + "main_wclk" + "aux_wclk" + +* HDMI output device + +Required properties: + - compatible: should be "zte,zx296718-hdmi" + - reg: Physical base address and length of the HDMI device IO region + - interrupts : HDMI interrupt number to CPU + - clocks: A list of phandle + clock-specifier pairs, one for each entry + in 'clock-names' + - clock-names: A list of clock names. The following clocks are required: + "osc_cec" + "osc_clk" + "xclk" + +Example: + +vou: vou@1440000 { + compatible = "zte,zx296718-vou"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x1440000 0x10000>; + + dpc: dpc@0 { + compatible = "zte,zx296718-dpc"; + reg = <0x0000 0x1000>, <0x1000 0x1000>, + <0x5000 0x1000>, <0x6000 0x1000>, + <0xa000 0x1000>; + reg-names = "osd", "timing_ctrl", + "dtrc", "vou_ctrl", + "otfppu"; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&topcrm VOU_ACLK>, <&topcrm VOU_PPU_WCLK>, + <&topcrm VOU_MAIN_WCLK>, <&topcrm VOU_AUX_WCLK>; + clock-names = "aclk", "ppu_wclk", + "main_wclk", "aux_wclk"; + }; + + hdmi: hdmi@c000 { + compatible = "zte,zx296718-hdmi"; + reg = <0xc000 0x4000>; + interrupts = <GIC_SPI 82 IRQ_TYPE_EDGE_RISING>; + clocks = <&topcrm HDMI_OSC_CEC>, + <&topcrm HDMI_OSC_CLK>, + <&topcrm HDMI_XCLK>; + clock-names = "osc_cec", "osc_clk", "xclk"; + }; +}; diff --git a/Documentation/devicetree/bindings/dma/nbpfaxi.txt b/Documentation/devicetree/bindings/dma/nbpfaxi.txt index d5e2522b9ec1..d2e1e62e346a 100644 --- a/Documentation/devicetree/bindings/dma/nbpfaxi.txt +++ b/Documentation/devicetree/bindings/dma/nbpfaxi.txt @@ -23,6 +23,14 @@ Required properties #define NBPF_SLAVE_RQ_LEVEL 4 Optional properties: +- max-burst-mem-read: limit burst size for memory reads + (DMA_MEM_TO_MEM/DMA_MEM_TO_DEV) to this value, specified in bytes, rather + than using the maximum burst size allowed by the hardware's buffer size. +- max-burst-mem-write: limit burst size for memory writes + (DMA_DEV_TO_MEM/DMA_MEM_TO_MEM) to this value, specified in bytes, rather + than using the maximum burst size allowed by the hardware's buffer size. + If both max-burst-mem-read and max-burst-mem-write are set, DMA_MEM_TO_MEM + will use the lower value. You can use dma-channels and dma-requests as described in dma.txt, although they won't be used, this information is derived from the compatibility string. diff --git a/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt b/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt index fd5618bd8fbc..55492c264d17 100644 --- a/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt +++ b/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt @@ -5,13 +5,13 @@ memcpy and memset capabilities. It has been designed for virtualized environments. Each HIDMA HW instance consists of multiple DMA channels. These channels -share the same bandwidth. The bandwidth utilization can be parititioned +share the same bandwidth. The bandwidth utilization can be partitioned among channels based on the priority and weight assignments. There are only two priority levels and 15 weigh assignments possible. Other parameters here determine how much of the system bus this HIDMA -instance can use like maximum read/write request and and number of bytes to +instance can use like maximum read/write request and number of bytes to read/write in a single burst. Main node required properties: @@ -47,12 +47,18 @@ When the OS is not in control of the management interface (i.e. it's a guest), the channel nodes appear on their own, not under a management node. Required properties: -- compatible: must contain "qcom,hidma-1.0" +- compatible: must contain "qcom,hidma-1.0" for initial HW or "qcom,hidma-1.1" +for MSI capable HW. - reg: Addresses for the transfer and event channel - interrupts: Should contain the event interrupt - desc-count: Number of asynchronous requests this channel can handle - iommus: required a iommu node +Optional properties for MSI: +- msi-parent : See the generic MSI binding described in + devicetree/bindings/interrupt-controller/msi.txt for a description of the + msi-parent property. + Example: Hypervisor OS configuration: diff --git a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt index 5f2ce669789a..3316a9c2e638 100644 --- a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt +++ b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt @@ -24,6 +24,7 @@ Required Properties: - "renesas,dmac-r8a7793" (R-Car M2-N) - "renesas,dmac-r8a7794" (R-Car E2) - "renesas,dmac-r8a7795" (R-Car H3) + - "renesas,dmac-r8a7796" (R-Car M3-W) - reg: base address and length of the registers block for the DMAC diff --git a/Documentation/devicetree/bindings/dma/snps-dma.txt b/Documentation/devicetree/bindings/dma/snps-dma.txt index 0f5583293c9c..4775c66f4508 100644 --- a/Documentation/devicetree/bindings/dma/snps-dma.txt +++ b/Documentation/devicetree/bindings/dma/snps-dma.txt @@ -27,6 +27,8 @@ Optional properties: that services interrupts for this device - is_private: The device channels should be marked as private and not for by the general purpose DMA channel allocator. False if not passed. +- multi-block: Multi block transfers supported by hardware. Array property with + one cell per channel. 0: not supported, 1 (default): supported. Example: diff --git a/Documentation/devicetree/bindings/dma/st_fdma.txt b/Documentation/devicetree/bindings/dma/st_fdma.txt new file mode 100644 index 000000000000..495d853c569b --- /dev/null +++ b/Documentation/devicetree/bindings/dma/st_fdma.txt @@ -0,0 +1,87 @@ +* STMicroelectronics Flexible Direct Memory Access Device Tree bindings + +The FDMA is a general-purpose direct memory access controller capable of +supporting 16 independent DMA channels. It accepts up to 32 DMA requests. +The FDMA is based on a Slim processor which requires a firmware. + +* FDMA Controller + +Required properties: +- compatible : Should be one of + - st,stih407-fdma-mpe31-11, "st,slim-rproc"; + - st,stih407-fdma-mpe31-12, "st,slim-rproc"; + - st,stih407-fdma-mpe31-13, "st,slim-rproc"; +- reg : Should contain an entry for each name in reg-names +- reg-names : Must contain "slimcore", "dmem", "peripherals", "imem" entries +- interrupts : Should contain one interrupt shared by all channels +- dma-channels : Number of channels supported by the controller +- #dma-cells : Must be <3>. See DMA client section below +- clocks : Must contain an entry for each clock +See: Documentation/devicetree/bindings/clock/clock-bindings.txt + + +Example: + + fdma0: dma-controller@8e20000 { + compatible = "st,stih407-fdma-mpe31-11", "st,slim-rproc"; + reg = <0x8e20000 0x8000>, + <0x8e30000 0x3000>, + <0x8e37000 0x1000>, + <0x8e38000 0x8000>; + reg-names = "slimcore", "dmem", "peripherals", "imem"; + clocks = <&clk_s_c0_flexgen CLK_FDMA>, + <&clk_s_c0_flexgen CLK_EXT2F_A9>, + <&clk_s_c0_flexgen CLK_EXT2F_A9>, + <&clk_s_c0_flexgen CLK_EXT2F_A9>; + interrupts = <GIC_SPI 5 IRQ_TYPE_NONE>; + dma-channels = <16>; + #dma-cells = <3>; + }; + +* DMA client + +Required properties: +- dmas: Comma separated list of dma channel requests +- dma-names: Names of the aforementioned requested channels + +Each dmas request consists of 4 cells: +1. A phandle pointing to the FDMA controller +2. The request line number +3. A 32bit mask specifying (see include/linux/platform_data/dma-st-fdma.h) + -bit 2-0: Holdoff value, dreq will be masked for + 0x0: 0-0.5us + 0x1: 0.5-1us + 0x2: 1-1.5us + -bit 17: data swap + 0x0: disabled + 0x1: enabled + -bit 21: Increment Address + 0x0: no address increment between transfers + 0x1: increment address between transfers + -bit 22: 2 STBus Initiator Coprocessor interface + 0x0: high priority port + 0x1: low priority port +4. transfers type + 0 free running + 1 paced + +Example: + + sti_uni_player2: sti-uni-player@2 { + compatible = "st,sti-uni-player"; + status = "disabled"; + #sound-dai-cells = <0>; + st,syscfg = <&syscfg_core>; + clocks = <&clk_s_d0_flexgen CLK_PCM_2>; + assigned-clocks = <&clk_s_d0_flexgen CLK_PCM_2>; + assigned-clock-parents = <&clk_s_d0_quadfs 2>; + assigned-clock-rates = <50000000>; + reg = <0x8D82000 0x158>; + interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>; + dmas = <&fdma0 4 0 1>; + dai-name = "Uni Player #1 (DAC)"; + dma-names = "tx"; + st,uniperiph-id = <2>; + st,version = <5>; + st,mode = "PCM"; + }; diff --git a/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt b/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt index af0b903de293..dfc14f71e81f 100644 --- a/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt +++ b/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt @@ -5,7 +5,10 @@ connected to a GPIO pin. Required properties: - compatible: Should be "linux,extcon-usb-gpio" + +Either one of id-gpio or vbus-gpio must be present. Both can be present as well. - id-gpio: gpio for USB ID pin. See gpio binding. +- vbus-gpio: gpio for USB VBUS pin. Example: Examples of extcon-usb-gpio node in dra7-evm.dts as listed below: extcon_usb1 { diff --git a/Documentation/devicetree/bindings/fpga/altera-fpga2sdram-bridge.txt b/Documentation/devicetree/bindings/fpga/altera-fpga2sdram-bridge.txt new file mode 100644 index 000000000000..817a8d4bf903 --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/altera-fpga2sdram-bridge.txt @@ -0,0 +1,16 @@ +Altera FPGA To SDRAM Bridge Driver + +Required properties: +- compatible : Should contain "altr,socfpga-fpga2sdram-bridge" + +Optional properties: +- bridge-enable : 0 if driver should disable bridge at startup + 1 if driver should enable bridge at startup + Default is to leave bridge in current state. + +Example: + fpga_bridge3: fpga-bridge@ffc25080 { + compatible = "altr,socfpga-fpga2sdram-bridge"; + reg = <0xffc25080 0x4>; + bridge-enable = <0>; + }; diff --git a/Documentation/devicetree/bindings/fpga/altera-freeze-bridge.txt b/Documentation/devicetree/bindings/fpga/altera-freeze-bridge.txt new file mode 100644 index 000000000000..f8e288c71b2d --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/altera-freeze-bridge.txt @@ -0,0 +1,23 @@ +Altera Freeze Bridge Controller Driver + +The Altera Freeze Bridge Controller manages one or more freeze bridges. +The controller can freeze/disable the bridges which prevents signal +changes from passing through the bridge. The controller can also +unfreeze/enable the bridges which allows traffic to pass through the +bridge normally. + +Required properties: +- compatible : Should contain "altr,freeze-bridge-controller" +- regs : base address and size for freeze bridge module + +Optional properties: +- bridge-enable : 0 if driver should disable bridge at startup + 1 if driver should enable bridge at startup + Default is to leave bridge in current state. + +Example: + freeze-controller@100000450 { + compatible = "altr,freeze-bridge-controller"; + regs = <0x1000 0x10>; + bridge-enable = <0>; + }; diff --git a/Documentation/devicetree/bindings/fpga/altera-hps2fpga-bridge.txt b/Documentation/devicetree/bindings/fpga/altera-hps2fpga-bridge.txt new file mode 100644 index 000000000000..6406f9337eeb --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/altera-hps2fpga-bridge.txt @@ -0,0 +1,39 @@ +Altera FPGA/HPS Bridge Driver + +Required properties: +- regs : base address and size for AXI bridge module +- compatible : Should contain one of: + "altr,socfpga-lwhps2fpga-bridge", + "altr,socfpga-hps2fpga-bridge", or + "altr,socfpga-fpga2hps-bridge" +- resets : Phandle and reset specifier for this bridge's reset +- clocks : Clocks used by this module. + +Optional properties: +- bridge-enable : 0 if driver should disable bridge at startup. + 1 if driver should enable bridge at startup. + Default is to leave bridge in its current state. + +Example: + fpga_bridge0: fpga-bridge@ff400000 { + compatible = "altr,socfpga-lwhps2fpga-bridge"; + reg = <0xff400000 0x100000>; + resets = <&rst LWHPS2FPGA_RESET>; + clocks = <&l4_main_clk>; + bridge-enable = <0>; + }; + + fpga_bridge1: fpga-bridge@ff500000 { + compatible = "altr,socfpga-hps2fpga-bridge"; + reg = <0xff500000 0x10000>; + resets = <&rst HPS2FPGA_RESET>; + clocks = <&l4_main_clk>; + bridge-enable = <1>; + }; + + fpga_bridge2: fpga-bridge@ff600000 { + compatible = "altr,socfpga-fpga2hps-bridge"; + reg = <0xff600000 0x100000>; + resets = <&rst FPGA2HPS_RESET>; + clocks = <&l4_main_clk>; + }; diff --git a/Documentation/devicetree/bindings/fpga/altera-socfpga-a10-fpga-mgr.txt b/Documentation/devicetree/bindings/fpga/altera-socfpga-a10-fpga-mgr.txt new file mode 100644 index 000000000000..2fd8e7a84734 --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/altera-socfpga-a10-fpga-mgr.txt @@ -0,0 +1,19 @@ +Altera SOCFPGA Arria10 FPGA Manager + +Required properties: +- compatible : should contain "altr,socfpga-a10-fpga-mgr" +- reg : base address and size for memory mapped io. + - The first index is for FPGA manager register access. + - The second index is for writing FPGA configuration data. +- resets : Phandle and reset specifier for the device's reset. +- clocks : Clocks used by the device. + +Example: + + fpga_mgr: fpga-mgr@ffd03000 { + compatible = "altr,socfpga-a10-fpga-mgr"; + reg = <0xffd03000 0x100 + 0xffcfe400 0x20>; + clocks = <&l4_mp_clk>; + resets = <&rst FPGAMGR_RESET>; + }; diff --git a/Documentation/devicetree/bindings/fpga/fpga-region.txt b/Documentation/devicetree/bindings/fpga/fpga-region.txt new file mode 100644 index 000000000000..3b32ba15a717 --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/fpga-region.txt @@ -0,0 +1,494 @@ +FPGA Region Device Tree Binding + +Alan Tull 2016 + + CONTENTS + - Introduction + - Terminology + - Sequence + - FPGA Region + - Supported Use Models + - Device Tree Examples + - Constraints + + +Introduction +============ + +FPGA Regions represent FPGA's and partial reconfiguration regions of FPGA's in +the Device Tree. FPGA Regions provide a way to program FPGAs under device tree +control. + +This device tree binding document hits some of the high points of FPGA usage and +attempts to include terminology used by both major FPGA manufacturers. This +document isn't a replacement for any manufacturers specifications for FPGA +usage. + + +Terminology +=========== + +Full Reconfiguration + * The entire FPGA is programmed. + +Partial Reconfiguration (PR) + * A section of an FPGA is reprogrammed while the rest of the FPGA is not + affected. + * Not all FPGA's support PR. + +Partial Reconfiguration Region (PRR) + * Also called a "reconfigurable partition" + * A PRR is a specific section of a FPGA reserved for reconfiguration. + * A base (or static) FPGA image may create a set of PRR's that later may + be independently reprogrammed many times. + * The size and specific location of each PRR is fixed. + * The connections at the edge of each PRR are fixed. The image that is loaded + into a PRR must fit and must use a subset of the region's connections. + * The busses within the FPGA are split such that each region gets its own + branch that may be gated independently. + +Persona + * Also called a "partial bit stream" + * An FPGA image that is designed to be loaded into a PRR. There may be + any number of personas designed to fit into a PRR, but only one at at time + may be loaded. + * A persona may create more regions. + +FPGA Bridge + * FPGA Bridges gate bus signals between a host and FPGA. + * FPGA Bridges should be disabled while the FPGA is being programmed to + prevent spurious signals on the cpu bus and to the soft logic. + * FPGA bridges may be actual hardware or soft logic on an FPGA. + * During Full Reconfiguration, hardware bridges between the host and FPGA + will be disabled. + * During Partial Reconfiguration of a specific region, that region's bridge + will be used to gate the busses. Traffic to other regions is not affected. + * In some implementations, the FPGA Manager transparantly handles gating the + buses, eliminating the need to show the hardware FPGA bridges in the + device tree. + * An FPGA image may create a set of reprogrammable regions, each having its + own bridge and its own split of the busses in the FPGA. + +FPGA Manager + * An FPGA Manager is a hardware block that programs an FPGA under the control + of a host processor. + +Base Image + * Also called the "static image" + * An FPGA image that is designed to do full reconfiguration of the FPGA. + * A base image may set up a set of partial reconfiguration regions that may + later be reprogrammed. + + ---------------- ---------------------------------- + | Host CPU | | FPGA | + | | | | + | ----| | ----------- -------- | + | | H | | |==>| Bridge0 |<==>| PRR0 | | + | | W | | | ----------- -------- | + | | | | | | + | | B |<=====>|<==| ----------- -------- | + | | R | | |==>| Bridge1 |<==>| PRR1 | | + | | I | | | ----------- -------- | + | | D | | | | + | | G | | | ----------- -------- | + | | E | | |==>| Bridge2 |<==>| PRR2 | | + | ----| | ----------- -------- | + | | | | + ---------------- ---------------------------------- + +Figure 1: An FPGA set up with a base image that created three regions. Each +region (PRR0-2) gets its own split of the busses that is independently gated by +a soft logic bridge (Bridge0-2) in the FPGA. The contents of each PRR can be +reprogrammed independently while the rest of the system continues to function. + + +Sequence +======== + +When a DT overlay that targets a FPGA Region is applied, the FPGA Region will +do the following: + + 1. Disable appropriate FPGA bridges. + 2. Program the FPGA using the FPGA manager. + 3. Enable the FPGA bridges. + 4. The Device Tree overlay is accepted into the live tree. + 5. Child devices are populated. + +When the overlay is removed, the child nodes will be removed and the FPGA Region +will disable the bridges. + + +FPGA Region +=========== + +FPGA Regions represent FPGA's and FPGA PR regions in the device tree. An FPGA +Region brings together the elements needed to program on a running system and +add the child devices: + + * FPGA Manager + * FPGA Bridges + * image-specific information needed to to the programming. + * child nodes + +The intended use is that a Device Tree overlay (DTO) can be used to reprogram an +FPGA while an operating system is running. + +An FPGA Region that exists in the live Device Tree reflects the current state. +If the live tree shows a "firmware-name" property or child nodes under a FPGA +Region, the FPGA already has been programmed. A DTO that targets a FPGA Region +and adds the "firmware-name" property is taken as a request to reprogram the +FPGA. After reprogramming is successful, the overlay is accepted into the live +tree. + +The base FPGA Region in the device tree represents the FPGA and supports full +reconfiguration. It must include a phandle to an FPGA Manager. The base +FPGA region will be the child of one of the hardware bridges (the bridge that +allows register access) between the cpu and the FPGA. If there are more than +one bridge to control during FPGA programming, the region will also contain a +list of phandles to the additional hardware FPGA Bridges. + +For partial reconfiguration (PR), each PR region will have an FPGA Region. +These FPGA regions are children of FPGA bridges which are then children of the +base FPGA region. The "Full Reconfiguration to add PRR's" example below shows +this. + +If an FPGA Region does not specify a FPGA Manager, it will inherit the FPGA +Manager specified by its ancestor FPGA Region. This supports both the case +where the same FPGA Manager is used for all of a FPGA as well the case where +a different FPGA Manager is used for each region. + +FPGA Regions do not inherit their ancestor FPGA regions' bridges. This prevents +shutting down bridges that are upstream from the other active regions while one +region is getting reconfigured (see Figure 1 above). During PR, the FPGA's +hardware bridges remain enabled. The PR regions' bridges will be FPGA bridges +within the static image of the FPGA. + +Required properties: +- compatible : should contain "fpga-region" +- fpga-mgr : should contain a phandle to an FPGA Manager. Child FPGA Regions + inherit this property from their ancestor regions. A fpga-mgr property + in a region will override any inherited FPGA manager. +- #address-cells, #size-cells, ranges : must be present to handle address space + mapping for child nodes. + +Optional properties: +- firmware-name : should contain the name of an FPGA image file located on the + firmware search path. If this property shows up in a live device tree + it indicates that the FPGA has already been programmed with this image. + If this property is in an overlay targeting a FPGA region, it is a + request to program the FPGA with that image. +- fpga-bridges : should contain a list of phandles to FPGA Bridges that must be + controlled during FPGA programming along with the parent FPGA bridge. + This property is optional if the FPGA Manager handles the bridges. + If the fpga-region is the child of a fpga-bridge, the list should not + contain the parent bridge. +- partial-fpga-config : boolean, set if partial reconfiguration is to be done, + otherwise full reconfiguration is done. +- external-fpga-config : boolean, set if the FPGA has already been configured + prior to OS boot up. +- region-unfreeze-timeout-us : The maximum time in microseconds to wait for + bridges to successfully become enabled after the region has been + programmed. +- region-freeze-timeout-us : The maximum time in microseconds to wait for + bridges to successfully become disabled before the region has been + programmed. +- child nodes : devices in the FPGA after programming. + +In the example below, when an overlay is applied targeting fpga-region0, +fpga_mgr is used to program the FPGA. Two bridges are controlled during +programming: the parent fpga_bridge0 and fpga_bridge1. Because the region is +the child of fpga_bridge0, only fpga_bridge1 needs to be specified in the +fpga-bridges property. During programming, these bridges are disabled, the +firmware specified in the overlay is loaded to the FPGA using the FPGA manager +specified in the region. If FPGA programming succeeds, the bridges are +reenabled and the overlay makes it into the live device tree. The child devices +are then populated. If FPGA programming fails, the bridges are left disabled +and the overlay is rejected. The overlay's ranges property maps the lwhps +bridge's region (0xff200000) and the hps bridge's region (0xc0000000) for use by +the two child devices. + +Example: +Base tree contains: + + fpga_mgr: fpga-mgr@ff706000 { + compatible = "altr,socfpga-fpga-mgr"; + reg = <0xff706000 0x1000 + 0xffb90000 0x20>; + interrupts = <0 175 4>; + }; + + fpga_bridge0: fpga-bridge@ff400000 { + compatible = "altr,socfpga-lwhps2fpga-bridge"; + reg = <0xff400000 0x100000>; + resets = <&rst LWHPS2FPGA_RESET>; + clocks = <&l4_main_clk>; + + #address-cells = <1>; + #size-cells = <1>; + ranges; + + fpga_region0: fpga-region0 { + compatible = "fpga-region"; + fpga-mgr = <&fpga_mgr>; + }; + }; + + fpga_bridge1: fpga-bridge@ff500000 { + compatible = "altr,socfpga-hps2fpga-bridge"; + reg = <0xff500000 0x10000>; + resets = <&rst HPS2FPGA_RESET>; + clocks = <&l4_main_clk>; + }; + +Overlay contains: + +/dts-v1/ /plugin/; +/ { + fragment@0 { + target = <&fpga_region0>; + #address-cells = <1>; + #size-cells = <1>; + __overlay__ { + #address-cells = <1>; + #size-cells = <1>; + + firmware-name = "soc_system.rbf"; + fpga-bridges = <&fpga_bridge1>; + ranges = <0x20000 0xff200000 0x100000>, + <0x0 0xc0000000 0x20000000>; + + gpio@10040 { + compatible = "altr,pio-1.0"; + reg = <0x10040 0x20>; + altr,gpio-bank-width = <4>; + #gpio-cells = <2>; + clocks = <2>; + gpio-controller; + }; + + onchip-memory { + device_type = "memory"; + compatible = "altr,onchipmem-15.1"; + reg = <0x0 0x10000>; + }; + }; + }; +}; + + +Supported Use Models +==================== + +In all cases the live DT must have the FPGA Manager, FPGA Bridges (if any), and +a FPGA Region. The target of the Device Tree Overlay is the FPGA Region. Some +uses are specific to a FPGA device. + + * No FPGA Bridges + In this case, the FPGA Manager which programs the FPGA also handles the + bridges behind the scenes. No FPGA Bridge devices are needed for full + reconfiguration. + + * Full reconfiguration with hardware bridges + In this case, there are hardware bridges between the processor and FPGA that + need to be controlled during full reconfiguration. Before the overlay is + applied, the live DT must include the FPGA Manager, FPGA Bridges, and a + FPGA Region. The FPGA Region is the child of the bridge that allows + register access to the FPGA. Additional bridges may be listed in a + fpga-bridges property in the FPGA region or in the device tree overlay. + + * Partial reconfiguration with bridges in the FPGA + In this case, the FPGA will have one or more PRR's that may be programmed + separately while the rest of the FPGA can remain active. To manage this, + bridges need to exist in the FPGA that can gate the buses going to each FPGA + region while the buses are enabled for other sections. Before any partial + reconfiguration can be done, a base FPGA image must be loaded which includes + PRR's with FPGA bridges. The device tree should have a FPGA region for each + PRR. + +Device Tree Examples +==================== + +The intention of this section is to give some simple examples, focusing on +the placement of the elements detailed above, especially: + * FPGA Manager + * FPGA Bridges + * FPGA Region + * ranges + * target-path or target + +For the purposes of this section, I'm dividing the Device Tree into two parts, +each with its own requirements. The two parts are: + * The live DT prior to the overlay being added + * The DT overlay + +The live Device Tree must contain an FPGA Region, an FPGA Manager, and any FPGA +Bridges. The FPGA Region's "fpga-mgr" property specifies the manager by phandle +to handle programming the FPGA. If the FPGA Region is the child of another FPGA +Region, the parent's FPGA Manager is used. If FPGA Bridges need to be involved, +they are specified in the FPGA Region by the "fpga-bridges" property. During +FPGA programming, the FPGA Region will disable the bridges that are in its +"fpga-bridges" list and will re-enable them after FPGA programming has +succeeded. + +The Device Tree Overlay will contain: + * "target-path" or "target" + The insertion point where the the contents of the overlay will go into the + live tree. target-path is a full path, while target is a phandle. + * "ranges" + The address space mapping from processor to FPGA bus(ses). + * "firmware-name" + Specifies the name of the FPGA image file on the firmware search + path. The search path is described in the firmware class documentation. + * "partial-fpga-config" + This binding is a boolean and should be present if partial reconfiguration + is to be done. + * child nodes corresponding to hardware that will be loaded in this region of + the FPGA. + +Device Tree Example: Full Reconfiguration without Bridges +========================================================= + +Live Device Tree contains: + fpga_mgr0: fpga-mgr@f8007000 { + compatible = "xlnx,zynq-devcfg-1.0"; + reg = <0xf8007000 0x100>; + interrupt-parent = <&intc>; + interrupts = <0 8 4>; + clocks = <&clkc 12>; + clock-names = "ref_clk"; + syscon = <&slcr>; + }; + + fpga_region0: fpga-region0 { + compatible = "fpga-region"; + fpga-mgr = <&fpga_mgr0>; + #address-cells = <0x1>; + #size-cells = <0x1>; + ranges; + }; + +DT Overlay contains: +/dts-v1/ /plugin/; +/ { +fragment@0 { + target = <&fpga_region0>; + #address-cells = <1>; + #size-cells = <1>; + __overlay__ { + #address-cells = <1>; + #size-cells = <1>; + + firmware-name = "zynq-gpio.bin"; + + gpio1: gpio@40000000 { + compatible = "xlnx,xps-gpio-1.00.a"; + reg = <0x40000000 0x10000>; + gpio-controller; + #gpio-cells = <0x2>; + xlnx,gpio-width= <0x6>; + }; + }; +}; + +Device Tree Example: Full Reconfiguration to add PRR's +====================================================== + +The base FPGA Region is specified similar to the first example above. + +This example programs the FPGA to have two regions that can later be partially +configured. Each region has its own bridge in the FPGA fabric. + +DT Overlay contains: +/dts-v1/ /plugin/; +/ { + fragment@0 { + target = <&fpga_region0>; + #address-cells = <1>; + #size-cells = <1>; + __overlay__ { + #address-cells = <1>; + #size-cells = <1>; + + firmware-name = "base.rbf"; + + fpga-bridge@4400 { + compatible = "altr,freeze-bridge"; + reg = <0x4400 0x10>; + + fpga_region1: fpga-region1 { + compatible = "fpga-region"; + #address-cells = <0x1>; + #size-cells = <0x1>; + ranges; + }; + }; + + fpga-bridge@4420 { + compatible = "altr,freeze-bridge"; + reg = <0x4420 0x10>; + + fpga_region2: fpga-region2 { + compatible = "fpga-region"; + #address-cells = <0x1>; + #size-cells = <0x1>; + ranges; + }; + }; + }; + }; +}; + +Device Tree Example: Partial Reconfiguration +============================================ + +This example reprograms one of the PRR's set up in the previous example. + +The sequence that occurs when this overlay is similar to the above, the only +differences are that the FPGA is partially reconfigured due to the +"partial-fpga-config" boolean and the only bridge that is controlled during +programming is the FPGA based bridge of fpga_region1. + +/dts-v1/ /plugin/; +/ { + fragment@0 { + target = <&fpga_region1>; + #address-cells = <1>; + #size-cells = <1>; + __overlay__ { + #address-cells = <1>; + #size-cells = <1>; + + firmware-name = "soc_image2.rbf"; + partial-fpga-config; + + gpio@10040 { + compatible = "altr,pio-1.0"; + reg = <0x10040 0x20>; + clocks = <0x2>; + altr,gpio-bank-width = <0x4>; + resetvalue = <0x0>; + #gpio-cells = <0x2>; + gpio-controller; + }; + }; + }; +}; + +Constraints +=========== + +It is beyond the scope of this document to fully describe all the FPGA design +constraints required to make partial reconfiguration work[1] [2] [3], but a few +deserve quick mention. + +A persona must have boundary connections that line up with those of the partion +or region it is designed to go into. + +During programming, transactions through those connections must be stopped and +the connections must be held at a fixed logic level. This can be achieved by +FPGA Bridges that exist on the FPGA fabric prior to the partial reconfiguration. + +-- +[1] www.altera.com/content/dam/altera-www/global/en_US/pdfs/literature/ug/ug_partrecon.pdf +[2] tspace.library.utoronto.ca/bitstream/1807/67932/1/Byma_Stuart_A_201411_MAS_thesis.pdf +[3] http://www.xilinx.com/support/documentation/sw_manuals/xilinx14_1/ug702.pdf diff --git a/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt b/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt deleted file mode 100644 index c809acb9c71b..000000000000 --- a/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt +++ /dev/null @@ -1,41 +0,0 @@ -SEMTECH SX150x GPIO expander bindings - - -Required properties: - -- compatible: should be "semtech,sx1506q", - "semtech,sx1508q", - "semtech,sx1509q", - "semtech,sx1502q". - -- reg: The I2C slave address for this device. - -- interrupt-parent: phandle of the parent interrupt controller. - -- interrupts: Interrupt specifier for the controllers interrupt. - -- #gpio-cells: Should be 2. The first cell is the GPIO number and the - second cell is used to specify optional parameters: - bit 0: polarity (0: normal, 1: inverted) - -- gpio-controller: Marks the device as a GPIO controller. - -- interrupt-controller: Marks the device as a interrupt controller. - -The GPIO expander can optionally be used as an interrupt controller, in -which case it uses the default two cell specifier as described in -Documentation/devicetree/bindings/interrupt-controller/interrupts.txt. - -Example: - - i2c_gpio_expander@20{ - #gpio-cells = <2>; - #interrupt-cells = <2>; - compatible = "semtech,sx1506q"; - reg = <0x20>; - interrupt-parent = <&gpio_1>; - interrupts = <16 0>; - - gpio-controller; - interrupt-controller; - }; diff --git a/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt b/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt index 928ed4f43907..966514744df4 100644 --- a/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt +++ b/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt @@ -3,7 +3,7 @@ Please refer to gpio.txt for generic information regarding GPIO bindings. Required properties: - - compatible: "oxsemi,ox810se-gpio" + - compatible: "oxsemi,ox810se-gpio" or "oxsemi,ox820-gpio" - reg: Base address and length for the device. - interrupts: The port interrupt shared by all pins. - gpio-controller: Marks the port as GPIO controller. diff --git a/Documentation/devicetree/bindings/hwmon/mcp3021.txt b/Documentation/devicetree/bindings/hwmon/mcp3021.txt new file mode 100644 index 000000000000..294318ba6914 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/mcp3021.txt @@ -0,0 +1,21 @@ +mcp3021 properties + +Required properties: +- compatible: Must be one of the following: + - "microchip,mcp3021" for mcp3021 + - "microchip,mcp3221" for mcp3221 +- reg: I2C address + +Optional properties: + +- reference-voltage-microvolt + Reference voltage in microvolt (uV) + +Example: + +mcp3021@4d { + compatible = "microchip,mcp3021"; + reg = <0x4d>; + + reference-voltage-microvolt = <4500000>; /* 4.5 V */ +}; diff --git a/Documentation/devicetree/bindings/hwmon/tmp108.txt b/Documentation/devicetree/bindings/hwmon/tmp108.txt new file mode 100644 index 000000000000..8c4b10df86d9 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/tmp108.txt @@ -0,0 +1,14 @@ +TMP108 temperature sensor +------------------------- + +This device supports I2C only. + +Requires node properties: +- compatible : "ti,tmp108" +- reg : the I2C address of the device. This is 0x48, 0x49, 0x4a, or 0x4b. + +Example: + tmp108@48 { + compatible = "ti,tmp108"; + reg = <0x48>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt b/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt new file mode 100644 index 000000000000..70c054a9a997 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt @@ -0,0 +1,20 @@ +* Freescale Low Power Inter IC (LPI2C) for i.MX + +Required properties: +- compatible : + - "fsl,imx7ulp-lpi2c" for LPI2C compatible with the one integrated on i.MX7ULP soc + - "fsl,imx8dv-lpi2c" for LPI2C compatible with the one integrated on i.MX8DV soc +- reg : address and length of the lpi2c master registers +- interrupt-parent : core interrupt controller +- interrupts : lpi2c interrupt +- clocks : lpi2c clock specifier + +Examples: + +lpi2c7: lpi2c7@40A50000 { + compatible = "fsl,imx8dv-lpi2c"; + reg = <0x40A50000 0x10000>; + interrupt-parent = <&intc>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7ULP_CLK_LPI2C7>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-pxa.txt b/Documentation/devicetree/bindings/i2c/i2c-pxa.txt index 12b78ac507e9..d30f0b11d853 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-pxa.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-pxa.txt @@ -7,6 +7,7 @@ Required properties : compatible processor, e.g. pxa168, pxa910, mmp2, mmp3. For the pxa2xx/pxa3xx, an additional node "mrvl,pxa-i2c" is required as shown in the example below. + For the Armada 3700, the compatible should be "marvell,armada-3700-i2c". Recommended properties : diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt index 239632a0d709..2b8bd33dbf8d 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt @@ -1,17 +1,25 @@ I2C for R-Car platforms Required properties: -- compatible: Must be one of - "renesas,i2c-rcar" - "renesas,i2c-r8a7778" - "renesas,i2c-r8a7779" - "renesas,i2c-r8a7790" - "renesas,i2c-r8a7791" - "renesas,i2c-r8a7792" - "renesas,i2c-r8a7793" - "renesas,i2c-r8a7794" - "renesas,i2c-r8a7795" - "renesas,i2c-r8a7796" +- compatible: + "renesas,i2c-r8a7778" if the device is a part of a R8A7778 SoC. + "renesas,i2c-r8a7779" if the device is a part of a R8A7779 SoC. + "renesas,i2c-r8a7790" if the device is a part of a R8A7790 SoC. + "renesas,i2c-r8a7791" if the device is a part of a R8A7791 SoC. + "renesas,i2c-r8a7792" if the device is a part of a R8A7792 SoC. + "renesas,i2c-r8a7793" if the device is a part of a R8A7793 SoC. + "renesas,i2c-r8a7794" if the device is a part of a R8A7794 SoC. + "renesas,i2c-r8a7795" if the device is a part of a R8A7795 SoC. + "renesas,i2c-r8a7796" if the device is a part of a R8A7796 SoC. + "renesas,rcar-gen1-i2c" for a generic R-Car Gen1 compatible device. + "renesas,rcar-gen2-i2c" for a generic R-Car Gen2 compatible device. + "renesas,rcar-gen3-i2c" for a generic R-Car Gen3 compatible device. + "renesas,i2c-rcar" (deprecated) + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first followed + by the generic version. + - reg: physical base address of the controller and length of memory mapped region. - interrupts: interrupt specifier. @@ -33,7 +41,7 @@ Examples : i2c0: i2c@e6508000 { #address-cells = <1>; #size-cells = <0>; - compatible = "renesas,i2c-r8a7791"; + compatible = "renesas,i2c-r8a7791", "renesas,rcar-gen2-i2c"; reg = <0 0xe6508000 0 0x40>; interrupts = <0 287 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp9_clks R8A7791_CLK_I2C0>; diff --git a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt index 214f94c25d37..7716acc55dec 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt @@ -1,8 +1,7 @@ Device tree configuration for Renesas IIC (sh_mobile) driver Required properties: -- compatible : "renesas,iic-<soctype>". "renesas,rmobile-iic" as fallback - Examples with soctypes are: +- compatible : - "renesas,iic-r8a73a4" (R-Mobile APE6) - "renesas,iic-r8a7740" (R-Mobile A1) - "renesas,iic-r8a7790" (R-Car H2) @@ -12,6 +11,17 @@ Required properties: - "renesas,iic-r8a7794" (R-Car E2) - "renesas,iic-r8a7795" (R-Car H3) - "renesas,iic-sh73a0" (SH-Mobile AG5) + - "renesas,rcar-gen2-iic" (generic R-Car Gen2 compatible device) + - "renesas,rcar-gen3-iic" (generic R-Car Gen3 compatible device) + - "renesas,rmobile-iic" (generic device) + + When compatible with a generic R-Car version, nodes + must list the SoC-specific version corresponding to + the platform first followed by the generic R-Car + version. + + renesas,rmobile-iic must always follow. + - reg : address start and address range size of device - interrupts : interrupt of device - clocks : clock for device @@ -31,7 +41,8 @@ Pinctrl properties might be needed, too. See there. Example: iic0: i2c@e6500000 { - compatible = "renesas,iic-r8a7790", "renesas,rmobile-iic"; + compatible = "renesas,iic-r8a7790", "renesas,rcar-gen2-iic", + "renesas,rmobile-iic"; reg = <0 0xe6500000 0 0x425>; interrupts = <0 174 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7790_CLK_IIC0>; diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index fbbad6446741..df720ca00fcf 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -39,11 +39,13 @@ dallas,ds75 Digital Thermometer and Thermostat dlg,da9053 DA9053: flexible system level PMIC with multicore support dlg,da9063 DA9063: system PMIC for quad-core application processors domintech,dmard09 DMARD09: 3-axis Accelerometer +domintech,dmard10 DMARD10: 3-axis Accelerometer epson,rx8010 I2C-BUS INTERFACE REAL TIME CLOCK MODULE epson,rx8025 High-Stability. I2C-Bus INTERFACE REAL TIME CLOCK MODULE epson,rx8581 I2C-BUS INTERFACE REAL TIME CLOCK MODULE fsl,mag3110 MAG3110: Xtrinsic High Accuracy, 3D Magnetometer fsl,mc13892 MC13892: Power Management Integrated Circuit (PMIC) for i.MX35/51 +fsl,mma7660 MMA7660FC: 3-Axis Orientation/Motion Detection Sensor fsl,mma8450 MMA8450Q: Xtrinsic Low-power, 3-axis Xtrinsic Accelerometer fsl,mpl3115 MPL3115: Absolute Digital Pressure Sensor fsl,mpr121 MPR121: Proximity Capacitive Touch Sensor Controller @@ -57,6 +59,7 @@ maxim,max1237 Low-Power, 4-/12-Channel, 2-Wire Serial, 12-Bit ADCs maxim,max6625 9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface mc,rv3029c2 Real Time Clock Module with I2C-Bus mcube,mc3230 mCube 3-axis 8-bit digital accelerometer +memsic,mxc6225 MEMSIC 2-axis 8-bit digital accelerometer microchip,mcp4531-502 Microchip 7-bit Single I2C Digital Potentiometer (5k) microchip,mcp4531-103 Microchip 7-bit Single I2C Digital Potentiometer (10k) microchip,mcp4531-503 Microchip 7-bit Single I2C Digital Potentiometer (50k) @@ -121,6 +124,11 @@ microchip,mcp4662-502 Microchip 8-bit Dual I2C Digital Potentiometer with NV Mem microchip,mcp4662-103 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (10k) microchip,mcp4662-503 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (50k) microchip,mcp4662-104 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (100k) +microchip,tc654 PWM Fan Speed Controller With Fan Fault Detection +microchip,tc655 PWM Fan Speed Controller With Fan Fault Detection +miramems,da226 MiraMEMS DA226 2-axis 14-bit digital accelerometer +miramems,da280 MiraMEMS DA280 3-axis 14-bit digital accelerometer +miramems,da311 MiraMEMS DA311 3-axis 12-bit digital accelerometer national,lm63 Temperature sensor with integrated fan control national,lm75 I2C TEMP SENSOR national,lm80 Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor @@ -146,6 +154,7 @@ ricoh,rv5c387a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC samsung,24ad0xd1 S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power) sgx,vz89x SGX Sensortech VZ89X Sensors sii,s35390a 2-wire CMOS real-time clock +silabs,si7020 Relative Humidity and Temperature Sensors skyworks,sky81452 Skyworks SKY81452: Six-Channel White LED Driver with Touch Panel Bias Supply st,24c256 i2c serial eeprom (24cxx) st,m41t00 Serial real-time clock (RTC) diff --git a/Documentation/devicetree/bindings/iio/adc/envelope-detector.txt b/Documentation/devicetree/bindings/iio/adc/envelope-detector.txt new file mode 100644 index 000000000000..27544bdd4478 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/envelope-detector.txt @@ -0,0 +1,54 @@ +Bindings for ADC envelope detector using a DAC and a comparator + +The DAC is used to find the peak level of an alternating voltage input +signal by a binary search using the output of a comparator wired to +an interrupt pin. Like so: + _ + | \ + input +------>-------|+ \ + | \ + .-------. | }---. + | | | / | + | dac|-->--|- / | + | | |_/ | + | | | + | | | + | irq|------<-------' + | | + '-------' + +Required properties: +- compatible: Should be "axentia,tse850-envelope-detector" +- io-channels: Channel node of the dac to be used for comparator input. +- io-channel-names: Should be "dac". +- interrupt specification for one client interrupt, + see ../../interrupt-controller/interrupts.txt for details. +- interrupt-names: Should be "comp". + +Example: + + &i2c { + dpot: mcp4651-104@28 { + compatible = "microchip,mcp4651-104"; + reg = <0x28>; + #io-channel-cells = <1>; + }; + }; + + dac: dac { + compatible = "dpot-dac"; + vref-supply = <®_3v3>; + io-channels = <&dpot 0>; + io-channel-names = "dpot"; + #io-channel-cells = <1>; + }; + + envelope-detector { + compatible = "axentia,tse850-envelope-detector"; + io-channels = <&dac 0>; + io-channel-names = "dac"; + + interrupt-parent = <&gpio>; + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + interrupt-names = "comp"; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt new file mode 100644 index 000000000000..49ed82e89870 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt @@ -0,0 +1,83 @@ +STMicroelectronics STM32 ADC device driver + +STM32 ADC is a successive approximation analog-to-digital converter. +It has several multiplexed input channels. Conversions can be performed +in single, continuous, scan or discontinuous mode. Result of the ADC is +stored in a left-aligned or right-aligned 32-bit data register. +Conversions can be launched in software or using hardware triggers. + +The analog watchdog feature allows the application to detect if the input +voltage goes beyond the user-defined, higher or lower thresholds. + +Each STM32 ADC block can have up to 3 ADC instances. + +Each instance supports two contexts to manage conversions, each one has its +own configurable sequence and trigger: +- regular conversion can be done in sequence, running in background +- injected conversions have higher priority, and so have the ability to + interrupt regular conversion sequence (either triggered in SW or HW). + Regular sequence is resumed, in case it has been interrupted. + +Contents of a stm32 adc root node: +----------------------------------- +Required properties: +- compatible: Should be "st,stm32f4-adc-core". +- reg: Offset and length of the ADC block register set. +- interrupts: Must contain the interrupt for ADC block. +- clocks: Clock for the analog circuitry (common to all ADCs). +- clock-names: Must be "adc". +- interrupt-controller: Identifies the controller node as interrupt-parent +- vref-supply: Phandle to the vref input analog reference voltage. +- #interrupt-cells = <1>; +- #address-cells = <1>; +- #size-cells = <0>; + +Optional properties: +- A pinctrl state named "default" for each ADC channel may be defined to set + inX ADC pins in mode of operation for analog input on external pin. + +Contents of a stm32 adc child node: +----------------------------------- +An ADC block node should contain at least one subnode, representing an +ADC instance available on the machine. + +Required properties: +- compatible: Should be "st,stm32f4-adc". +- reg: Offset of ADC instance in ADC block (e.g. may be 0x0, 0x100, 0x200). +- clocks: Input clock private to this ADC instance. +- interrupt-parent: Phandle to the parent interrupt controller. +- interrupts: IRQ Line for the ADC (e.g. may be 0 for adc@0, 1 for adc@100 or + 2 for adc@200). +- st,adc-channels: List of single-ended channels muxed for this ADC. + It can have up to 16 channels, numbered from 0 to 15 (resp. for in0..in15). +- #io-channel-cells = <1>: See the IIO bindings section "IIO consumers" in + Documentation/devicetree/bindings/iio/iio-bindings.txt + +Example: + adc: adc@40012000 { + compatible = "st,stm32f4-adc-core"; + reg = <0x40012000 0x400>; + interrupts = <18>; + clocks = <&rcc 0 168>; + clock-names = "adc"; + vref-supply = <®_vref>; + interrupt-controller; + pinctrl-names = "default"; + pinctrl-0 = <&adc3_in8_pin>; + + #interrupt-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + compatible = "st,stm32f4-adc"; + #io-channel-cells = <1>; + reg = <0x0>; + clocks = <&rcc 0 168>; + interrupt-parent = <&adc>; + interrupts = <0>; + st,adc-channels = <8>; + }; + ... + other adc child nodes follow... + }; diff --git a/Documentation/devicetree/bindings/iio/adc/ti-adc161s626.txt b/Documentation/devicetree/bindings/iio/adc/ti-adc161s626.txt index 9ed2315781e4..3d25011f0c99 100644 --- a/Documentation/devicetree/bindings/iio/adc/ti-adc161s626.txt +++ b/Documentation/devicetree/bindings/iio/adc/ti-adc161s626.txt @@ -3,6 +3,7 @@ Required properties: - compatible: Should be "ti,adc141s626" or "ti,adc161s626" - reg: spi chip select number for the device + - vdda-supply: supply voltage to VDDA pin Recommended properties: - spi-max-frequency: Definition as per @@ -11,6 +12,7 @@ Recommended properties: Example: adc@0 { compatible = "ti,adc161s626"; + vdda-supply = <&vdda_fixed>; reg = <0>; spi-max-frequency = <4300000>; }; diff --git a/Documentation/devicetree/bindings/iio/dac/dpot-dac.txt b/Documentation/devicetree/bindings/iio/dac/dpot-dac.txt new file mode 100644 index 000000000000..fdf47a01bfef --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/dpot-dac.txt @@ -0,0 +1,41 @@ +Bindings for DAC emulation using a digital potentiometer + +It is assumed that the dpot is used as a voltage divider between the +current dpot wiper setting and the maximum resistance of the dpot. The +divided voltage is provided by a vref regulator. + + .------. + .-----------. | | + | vref |--' .---. + | regulator |--. | | + '-----------' | | d | + | | p | + | | o | wiper + | | t |<---------+ + | | | + | '---' dac output voltage + | | + '------+------------+ + +Required properties: +- compatible: Should be "dpot-dac" +- vref-supply: The regulator supplying the voltage divider. +- io-channels: Channel node of the dpot to be used for the voltage division. +- io-channel-names: Should be "dpot". + +Example: + + &i2c { + dpot: mcp4651-503@28 { + compatible = "microchip,mcp4651-503"; + reg = <0x28>; + #io-channel-cells = <1>; + }; + }; + + dac { + compatible = "dpot-dac"; + vref-supply = <®_3v3>; + io-channels = <&dpot 0>; + io-channel-names = "dpot"; + }; diff --git a/Documentation/devicetree/bindings/iio/dac/mcp4725.txt b/Documentation/devicetree/bindings/iio/dac/mcp4725.txt new file mode 100644 index 000000000000..1bc6c093fbfe --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/mcp4725.txt @@ -0,0 +1,35 @@ +Microchip mcp4725 and mcp4726 DAC device driver + +Required properties: + - compatible: Must be "microchip,mcp4725" or "microchip,mcp4726" + - reg: Should contain the DAC I2C address + - vdd-supply: Phandle to the Vdd power supply. This supply is used as a + voltage reference on mcp4725. It is used as a voltage reference on + mcp4726 if there is no vref-supply specified. + +Optional properties (valid only for mcp4726): + - vref-supply: Optional phandle to the Vref power supply. Vref pin is + used as a voltage reference when this supply is specified. + - microchip,vref-buffered: Boolean to enable buffering of the external + Vref pin. This boolean is not valid without the vref-supply. Quoting + the datasheet: This is offered in cases where the reference voltage + does not have the current capability not to drop its voltage when + connected to the internal resistor ladder circuit. + +Examples: + + /* simple mcp4725 */ + mcp4725@60 { + compatible = "microchip,mcp4725"; + reg = <0x60>; + vdd-supply = <&vdac_vdd>; + }; + + /* mcp4726 with the buffered external reference voltage */ + mcp4726@60 { + compatible = "microchip,mcp4726"; + reg = <0x60>; + vdd-supply = <&vdac_vdd>; + vref-supply = <&vdac_vref>; + microchip,vref-buffered; + }; diff --git a/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.txt b/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.txt new file mode 100644 index 000000000000..b0d3b59966bc --- /dev/null +++ b/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.txt @@ -0,0 +1,46 @@ +Invensense MPU-3050 Gyroscope device tree bindings + +Required properties: + - compatible : should be "invensense,mpu3050" + - reg : the I2C address of the sensor + +Optional properties: + - interrupt-parent : should be the phandle for the interrupt controller + - interrupts : interrupt mapping for the trigger interrupt from the + internal oscillator. The following IRQ modes are supported: + IRQ_TYPE_EDGE_RISING, IRQ_TYPE_EDGE_FALLING, IRQ_TYPE_LEVEL_HIGH and + IRQ_TYPE_LEVEL_LOW. The driver should detect and configure the hardware + for the desired interrupt type. + - vdd-supply : supply regulator for the main power voltage. + - vlogic-supply : supply regulator for the signal voltage. + - mount-matrix : see iio/mount-matrix.txt + +Optional subnodes: + - The MPU-3050 will pass through and forward the I2C signals from the + incoming I2C bus, alternatively drive traffic to a slave device (usually + an accelerometer) on its own initiative. Therefore is supports a subnode + i2c gate node. For details see: i2c/i2c-gate.txt + +Example: + +mpu3050@68 { + compatible = "invensense,mpu3050"; + reg = <0x68>; + interrupt-parent = <&foo>; + interrupts = <12 IRQ_TYPE_EDGE_FALLING>; + vdd-supply = <&bar>; + vlogic-supply = <&baz>; + + /* External I2C interface */ + i2c-gate { + #address-cells = <1>; + #size-cells = <0>; + + fnord@18 { + compatible = "fnord"; + reg = <0x18>; + interrupt-parent = <&foo>; + interrupts = <13 IRQ_TYPE_EDGE_FALLING>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/iio/humidity/hts221.txt b/Documentation/devicetree/bindings/iio/humidity/hts221.txt new file mode 100644 index 000000000000..b20ab9c12080 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/humidity/hts221.txt @@ -0,0 +1,22 @@ +* HTS221 STM humidity + temperature sensor + +Required properties: +- compatible: should be "st,hts221" +- reg: i2c address of the sensor / spi cs line + +Optional properties: +- interrupt-parent: should be the phandle for the interrupt controller +- interrupts: interrupt mapping for IRQ. It should be configured with + flags IRQ_TYPE_LEVEL_HIGH or IRQ_TYPE_EDGE_RISING. + + Refer to interrupt-controller/interrupts.txt for generic interrupt + client node bindings. + +Example: + +hts221@5f { + compatible = "st,hts221"; + reg = <0x5f>; + interrupt-parent = <&gpio0>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>; +}; diff --git a/Documentation/devicetree/bindings/iio/light/isl29018.txt b/Documentation/devicetree/bindings/iio/light/isl29018.txt new file mode 100644 index 000000000000..425ab459e209 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/isl29018.txt @@ -0,0 +1,28 @@ +* ISL 29018/29023/29035 I2C ALS, Proximity, and Infrared sensor + +Required properties: + + - compatible: Should be one of + "isil,isl29018" + "isil,isl29023" + "isil,isl29035" + - reg: the I2C address of the device + +Optional properties: + + - interrupt-parent: should be the phandle for the interrupt controller + - interrupts: the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic interrupt client + node bindings. + + - vcc-supply: phandle to the regulator that provides power to the sensor. + +Example: + +isl29018@44 { + compatible = "isil,isl29018"; + reg = <0x44>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(Z, 2) IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/iio/light/tsl2583.txt b/Documentation/devicetree/bindings/iio/light/tsl2583.txt new file mode 100644 index 000000000000..8e2066c83f70 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/tsl2583.txt @@ -0,0 +1,26 @@ +* TAOS TSL 2580/2581/2583 ALS sensor + +Required properties: + + - compatible: Should be one of + "amstaos,tsl2580" + "amstaos,tsl2581" + "amstaos,tsl2583" + - reg: the I2C address of the device + +Optional properties: + + - interrupt-parent: should be the phandle for the interrupt controller + - interrupts: the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic interrupt client + node bindings. + + - vcc-supply: phandle to the regulator that provides power to the sensor. + +Example: + +tsl2581@29 { + compatible = "amstaos,tsl2581"; + reg = <0x29>; +}; diff --git a/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt b/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt new file mode 100644 index 000000000000..b9b621e94cd7 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt @@ -0,0 +1,30 @@ +* Texas Instruments LMP91000 potentiostat + +http://www.ti.com/lit/ds/symlink/lmp91000.pdf + +Required properties: + + - compatible: should be "ti,lmp91000" + - reg: the I2C address of the device + - io-channels: the phandle of the iio provider + + - ti,external-tia-resistor: if the property ti,tia-gain-ohm is not defined this + needs to be set to signal that an external resistor value is being used. + +Optional properties: + + - ti,tia-gain-ohm: ohm value of the internal resistor for the transimpedance + amplifier. Must be 2750, 3500, 7000, 14000, 35000, 120000, or 350000 ohms. + + - ti,rload-ohm: ohm value of the internal resistor load applied to the gas + sensor. Must be 10, 33, 50, or 100 (default) ohms. + +Example: + +lmp91000@48 { + compatible = "ti,lmp91000"; + reg = <0x48>; + ti,tia-gain-ohm = <7500>; + ti,rload = <100>; + io-channels = <&adc>; +}; diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt index e41fe340162b..c040c9ad1889 100644 --- a/Documentation/devicetree/bindings/iio/st-sensors.txt +++ b/Documentation/devicetree/bindings/iio/st-sensors.txt @@ -42,6 +42,7 @@ Accelerometers: - st,lsm303agr-accel - st,lis2dh12-accel - st,h3lis331dl-accel +- st,lng2dm-accel Gyroscopes: - st,l3g4200d-gyro diff --git a/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-bt-bmc.txt b/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-ibt-bmc.txt index fbbacd958240..6f28969af9dc 100644 --- a/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-bt-bmc.txt +++ b/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-ibt-bmc.txt @@ -6,7 +6,7 @@ perform in-band IPMI communication with their host. Required properties: -- compatible : should be "aspeed,ast2400-bt-bmc" +- compatible : should be "aspeed,ast2400-ibt-bmc" - reg: physical address and size of the registers Optional properties: @@ -17,7 +17,7 @@ Optional properties: Example: ibt@1e789140 { - compatible = "aspeed,ast2400-bt-bmc"; + compatible = "aspeed,ast2400-ibt-bmc"; reg = <0x1e789140 0x18>; interrupts = <8>; }; diff --git a/Documentation/devicetree/bindings/leds/pca963x.txt b/Documentation/devicetree/bindings/leds/pca963x.txt index dafbe9931c2b..dfbdb123a9bf 100644 --- a/Documentation/devicetree/bindings/leds/pca963x.txt +++ b/Documentation/devicetree/bindings/leds/pca963x.txt @@ -7,6 +7,9 @@ Optional properties: - nxp,totem-pole : use totem pole (push-pull) instead of open-drain (pca9632 defaults to open-drain, newer chips to totem pole) - nxp,hw-blink : use hardware blinking instead of software blinking +- nxp,period-scale : In some configurations, the chip blinks faster than expected. + This parameter provides a scaling ratio (fixed point, decimal divided + by 1000) to compensate, e.g. 1300=1.3x and 750=0.75x. Each led is represented as a sub-node of the nxp,pca963x device. diff --git a/Documentation/devicetree/bindings/mfd/lp873x.txt b/Documentation/devicetree/bindings/mfd/lp873x.txt index 52766c2035f7..ae9cf39bd101 100644 --- a/Documentation/devicetree/bindings/mfd/lp873x.txt +++ b/Documentation/devicetree/bindings/mfd/lp873x.txt @@ -7,6 +7,9 @@ Required properties: - #gpio-cells: Should be two. The first cell is the pin number and the second cell is used to specify flags. See ../gpio/gpio.txt for more information. + - xxx-in-supply: Phandle to parent supply node of each regulator + populated under regulators node. xxx can be + buck0, buck1, ldo0 or ldo1. - regulators: List of child nodes that specify the regulator initialization data. Example: @@ -17,6 +20,11 @@ pmic: lp8733@60 { gpio-controller; #gpio-cells = <2>; + buck0-in-supply = <&vsys_3v3>; + buck1-in-supply = <&vsys_3v3>; + ldo0-in-supply = <&vsys_3v3>; + ldo1-in-supply = <&vsys_3v3>; + regulators { lp8733_buck0: buck0 { regulator-name = "lp8733-buck0"; diff --git a/Documentation/devicetree/bindings/mfd/max77620.txt b/Documentation/devicetree/bindings/mfd/max77620.txt index 2ad44f7e4880..9c16d51cc15b 100644 --- a/Documentation/devicetree/bindings/mfd/max77620.txt +++ b/Documentation/devicetree/bindings/mfd/max77620.txt @@ -106,6 +106,18 @@ Here supported time periods by device in microseconds are as follows: MAX77620 supports 40, 80, 160, 320, 640, 1280, 2560 and 5120 microseconds. MAX20024 supports 20, 40, 80, 160, 320, 640, 1280 and 2540 microseconds. +-maxim,power-ok-control: configure map power ok bit + 1: Enables POK(Power OK) to control nRST_IO and GPIO1 + POK function. + 0: Disables POK control. + if property missing, do not configure MPOK bit. + If POK mapping is enabled for GPIO1/nRST_IO then, + GPIO1/nRST_IO pins are HIGH only if all rails + that have POK control enabled are HIGH. + If any of the rails goes down(which are enabled for POK + control) then, GPIO1/nRST_IO goes LOW. + this property is valid for max20024 only. + For DT binding details of different sub modules like GPIO, pincontrol, regulator, power, please refer respective device-tree binding document under their respective sub-system directories. diff --git a/Documentation/devicetree/bindings/mfd/tps65086.txt b/Documentation/devicetree/bindings/mfd/tps65086.txt index d3705612a846..9cfa886fe99f 100644 --- a/Documentation/devicetree/bindings/mfd/tps65086.txt +++ b/Documentation/devicetree/bindings/mfd/tps65086.txt @@ -23,7 +23,7 @@ Required properties: defined below. Optional regulator properties: - - ti,regulator-step-size-25mv : This is applicable for buck[1,2,6], set this + - ti,regulator-step-size-25mv : This is applicable for buck[1-6], set this if the regulator is factory set with a 25mv step voltage mapping. - ti,regulator-decay : This is applicable for buck[1-6], set this if diff --git a/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt new file mode 100644 index 000000000000..7f95ec400863 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt @@ -0,0 +1,32 @@ +Amlogic SD / eMMC controller for S905/GXBB family SoCs + +The MMC 5.1 compliant host controller on Amlogic provides the +interface for SD, eMMC and SDIO devices. + +This file documents the properties in addition to those available in +the MMC core bindings, documented by mmc.txt. + +Required properties: +- compatible : contains one of: + - "amlogic,meson-gx-mmc" + - "amlogic,meson-gxbb-mmc" + - "amlogic,meson-gxl-mmc" + - "amlogic,meson-gxm-mmc" +- clocks : A list of phandle + clock-specifier pairs for the clocks listed in clock-names. +- clock-names: Should contain the following: + "core" - Main peripheral bus clock + "clkin0" - Parent clock of internal mux + "clkin1" - Other parent clock of internal mux + The driver has an interal mux clock which switches between clkin0 and clkin1 depending on the + clock rate requested by the MMC core. + +Example: + + sd_emmc_a: mmc@70000 { + compatible = "amlogic,meson-gxbb-mmc"; + reg = <0x0 0x70000 0x0 0x2000>; + interrupts = < GIC_SPI 216 IRQ_TYPE_EDGE_RISING>; + clocks = <&clkc CLKID_SD_EMMC_A>, <&xtal>, <&clkc CLKID_FCLK_DIV2>; + clock-names = "core", "clkin0", "clkin1"; + pinctrl-0 = <&emmc_pins>; + }; diff --git a/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt b/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt index be56d2bd474a..954561d09a8e 100644 --- a/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt +++ b/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt @@ -7,6 +7,15 @@ Required properties: - compatible : Should be one of the following "brcm,bcm2835-sdhci" "brcm,sdhci-iproc-cygnus" + "brcm,sdhci-iproc" + +Use brcm2835-sdhci for Rasperry PI. + +Use sdhci-iproc-cygnus for Broadcom SDHCI Controllers +restricted to 32bit host accesses to SDHCI registers. + +Use sdhci-iproc for Broadcom SDHCI Controllers that allow standard +8, 16, 32-bit host access to SDHCI register. - clocks : The clock feeding the SDHCI controller. diff --git a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt index ff611fa66871..e4ba92aa035e 100644 --- a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt +++ b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt @@ -8,11 +8,14 @@ Required properties: - compatible: should be "renesas,mmcif-<soctype>", "renesas,sh-mmcif" as a fallback. Examples with <soctype> are: + - "renesas,mmcif-r8a73a4" for the MMCIF found in r8a73a4 SoCs - "renesas,mmcif-r8a7740" for the MMCIF found in r8a7740 SoCs + - "renesas,mmcif-r8a7778" for the MMCIF found in r8a7778 SoCs - "renesas,mmcif-r8a7790" for the MMCIF found in r8a7790 SoCs - "renesas,mmcif-r8a7791" for the MMCIF found in r8a7791 SoCs - "renesas,mmcif-r8a7793" for the MMCIF found in r8a7793 SoCs - "renesas,mmcif-r8a7794" for the MMCIF found in r8a7794 SoCs + - "renesas,mmcif-sh73a0" for the MMCIF found in sh73a0 SoCs - clocks: reference to the functional clock diff --git a/Documentation/devicetree/bindings/mmc/sdhci-cadence.txt b/Documentation/devicetree/bindings/mmc/sdhci-cadence.txt new file mode 100644 index 000000000000..750374fc9d94 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-cadence.txt @@ -0,0 +1,30 @@ +* Cadence SD/SDIO/eMMC Host Controller + +Required properties: +- compatible: should be "cdns,sd4hc". +- reg: offset and length of the register set for the device. +- interrupts: a single interrupt specifier. +- clocks: phandle to the input clock. + +Optional properties: +For eMMC configuration, supported speed modes are not indicated by the SDHCI +Capabilities Register. Instead, the following properties should be specified +if supported. See mmc.txt for details. +- mmc-ddr-1_8v +- mmc-ddr-1_2v +- mmc-hs200-1_8v +- mmc-hs200-1_2v +- mmc-hs400-1_8v +- mmc-hs400-1_2v + +Example: + emmc: sdhci@5a000000 { + compatible = "cdns,sd4hc"; + reg = <0x5a000000 0x400>; + interrupts = <0 78 4>; + clocks = <&clk 4>; + bus-width = <8>; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + }; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt index 485483a63d8c..0576264eab5e 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt @@ -17,6 +17,7 @@ Required properties: "iface" - Main peripheral bus clock (PCLK/HCLK - AHB Bus clock) (required) "core" - SDC MMC clock (MCLK) (required) "bus" - SDCC bus voter clock (optional) + "xo" - TCXO clock (optional) Example: diff --git a/Documentation/devicetree/bindings/mmc/sdhci.txt b/Documentation/devicetree/bindings/mmc/sdhci.txt new file mode 100644 index 000000000000..1c95a1a555c3 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci.txt @@ -0,0 +1,13 @@ +The properties specific for SD host controllers. For properties shared by MMC +host controllers refer to the mmc[1] bindings. + + [1] Documentation/devicetree/bindings/mmc/mmc.txt + +Optional properties: +- sdhci-caps-mask: The sdhci capabilities register is incorrect. This 64bit + property corresponds to the bits in the sdhci capabilty register. If the bit + is on in the mask then the bit is incorrect in the register and should be + turned off, before applying sdhci-caps. +- sdhci-caps: The sdhci capabilities register is incorrect. This 64bit + property corresponds to the bits in the sdhci capability register. If the + bit is on in the property then the bit should be turned on. diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt index 4e00e859e885..7fd17c3da116 100644 --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt @@ -43,6 +43,9 @@ Optional properties: reset signal present internally in some host controller IC designs. See Documentation/devicetree/bindings/reset/reset.txt for details. +* reset-names: request name for using "resets" property. Must be "reset". + (It will be used together with "resets" property.) + * clocks: from common clock binding: handle to biu and ciu clocks for the bus interface unit clock and the card interface unit clock. @@ -56,8 +59,9 @@ Optional properties: is specified and the ciu clock is specified then we'll try to set the ciu clock to this at probe time. -* clock-freq-min-max: Minimum and Maximum clock frequency for card output +* clock-freq-min-max (DEPRECATED): Minimum and Maximum clock frequency for card output clock(cclk_out). If it's not specified, max is 200MHZ and min is 400KHz by default. + (Use the "max-frequency" instead of "clock-freq-min-max".) * num-slots: specifies the number of slots supported by the controller. The number of physical slots actually used could be equal or less than the @@ -71,11 +75,6 @@ Optional properties: * card-detect-delay: Delay in milli-seconds before detecting card after card insert event. The default value is 0. -* supports-highspeed (DEPRECATED): Enables support for high speed cards (up to 50MHz) - (use "cap-mmc-highspeed" or "cap-sd-highspeed" instead) - -* broken-cd: as documented in mmc core bindings. - * vmmc-supply: The phandle to the regulator to use for vmmc. If this is specified we'll defer probe until we can find this regulator. @@ -103,6 +102,8 @@ board specific portions as listed below. interrupts = <0 75 0>; #address-cells = <1>; #size-cells = <0>; + resets = <&rst 20>; + reset-names = "reset"; }; [board specific internal DMA resources] diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index 13df9c2399c3..a1650edfd2b7 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -11,8 +11,8 @@ optional bindings can be used. Required properties: - compatible: "renesas,sdhi-shmobile" - a generic sh-mobile SDHI unit - "renesas,sdhi-sh7372" - SDHI IP on SH7372 SoC "renesas,sdhi-sh73a0" - SDHI IP on SH73A0 SoC + "renesas,sdhi-r7s72100" - SDHI IP on R7S72100 SoC "renesas,sdhi-r8a73a4" - SDHI IP on R8A73A4 SoC "renesas,sdhi-r8a7740" - SDHI IP on R8A7740 SoC "renesas,sdhi-r8a7778" - SDHI IP on R8A7778 SoC diff --git a/Documentation/devicetree/bindings/net/brcm,amac.txt b/Documentation/devicetree/bindings/net/brcm,amac.txt index ba5ecc1041a5..2fefa1a44afd 100644 --- a/Documentation/devicetree/bindings/net/brcm,amac.txt +++ b/Documentation/devicetree/bindings/net/brcm,amac.txt @@ -2,11 +2,17 @@ Broadcom AMAC Ethernet Controller Device Tree Bindings ------------------------------------------------------------- Required properties: - - compatible: "brcm,amac" or "brcm,nsp-amac" - - reg: Address and length of the GMAC registers, - Address and length of the GMAC IDM registers - - reg-names: Names of the registers. Must have both "amac_base" and - "idm_base" + - compatible: "brcm,amac" + "brcm,nsp-amac" + "brcm,ns2-amac" + - reg: Address and length of the register set for the device. It + contains the information of registers in the same order as + described by reg-names + - reg-names: Names of the registers. + "amac_base": Address and length of the GMAC registers + "idm_base": Address and length of the GMAC IDM registers + "nicpm_base": Address and length of the NIC Port Manager + registers (required for Northstar2) - interrupts: Interrupt number Optional properties: diff --git a/Documentation/devicetree/bindings/net/can/rcar_can.txt b/Documentation/devicetree/bindings/net/can/rcar_can.txt index 8d40ab27bc8c..06bb7cc334c8 100644 --- a/Documentation/devicetree/bindings/net/can/rcar_can.txt +++ b/Documentation/devicetree/bindings/net/can/rcar_can.txt @@ -10,6 +10,7 @@ Required properties: "renesas,can-r8a7793" if CAN controller is a part of R8A7793 SoC. "renesas,can-r8a7794" if CAN controller is a part of R8A7794 SoC. "renesas,can-r8a7795" if CAN controller is a part of R8A7795 SoC. + "renesas,can-r8a7796" if CAN controller is a part of R8A7796 SoC. "renesas,rcar-gen1-can" for a generic R-Car Gen1 compatible device. "renesas,rcar-gen2-can" for a generic R-Car Gen2 compatible device. "renesas,rcar-gen3-can" for a generic R-Car Gen3 compatible device. @@ -24,11 +25,12 @@ Required properties: - pinctrl-0: pin control group to be used for this controller. - pinctrl-names: must be "default". -Required properties for "renesas,can-r8a7795" compatible: -In R8A7795 SoC, "clkp2" can be CANFD clock. This is a div6 clock and can be -used by both CAN and CAN FD controller at the same time. It needs to be scaled -to maximum frequency if any of these controllers use it. This is done using -the below properties. +Required properties for "renesas,can-r8a7795" and "renesas,can-r8a7796" +compatible: +In R8A7795 and R8A7796 SoCs, "clkp2" can be CANFD clock. This is a div6 clock +and can be used by both CAN and CAN FD controller at the same time. It needs to +be scaled to maximum frequency if any of these controllers use it. This is done +using the below properties: - assigned-clocks: phandle of clkp2(CANFD) clock. - assigned-clock-rates: maximum frequency of this clock. diff --git a/Documentation/devicetree/bindings/net/can/rcar_canfd.txt b/Documentation/devicetree/bindings/net/can/rcar_canfd.txt index 22a6f10bab05..93c3a6ae32f9 100644 --- a/Documentation/devicetree/bindings/net/can/rcar_canfd.txt +++ b/Documentation/devicetree/bindings/net/can/rcar_canfd.txt @@ -5,13 +5,14 @@ Required properties: - compatible: Must contain one or more of the following: - "renesas,rcar-gen3-canfd" for R-Car Gen3 compatible controller. - "renesas,r8a7795-canfd" for R8A7795 (R-Car H3) compatible controller. + - "renesas,r8a7796-canfd" for R8A7796 (R-Car M3) compatible controller. When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first, followed by the family-specific and/or generic versions. - reg: physical base address and size of the R-Car CAN FD register map. -- interrupts: interrupt specifier for the Global & Channel interrupts +- interrupts: interrupt specifiers for the Channel & Global interrupts - clocks: phandles and clock specifiers for 3 clock inputs. - clock-names: 3 clock input name strings: "fck", "canfd", "can_clk". - pinctrl-0: pin control group to be used for this controller. @@ -23,11 +24,12 @@ The name of the child nodes are "channel0" and "channel1" respectively. Each child node supports the "status" property only, which is used to enable/disable the respective channel. -Required properties for "renesas,r8a7795-canfd" compatible: -In R8A7795 SoC, canfd clock is a div6 clock and can be used by both CAN -and CAN FD controller at the same time. It needs to be scaled to maximum -frequency if any of these controllers use it. This is done using the -below properties. +Required properties for "renesas,r8a7795-canfd" and "renesas,r8a7796-canfd" +compatible: +In R8A7795 and R8A7796 SoCs, canfd clock is a div6 clock and can be used by both +CAN and CAN FD controller at the same time. It needs to be scaled to maximum +frequency if any of these controllers use it. This is done using the below +properties: - assigned-clocks: phandle of canfd clock. - assigned-clock-rates: maximum frequency of this clock. diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index 5ad439f30135..ebda7c93453a 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -20,8 +20,6 @@ Required properties: - slaves : Specifies number for slaves - active_slave : Specifies the slave to use for time stamping, ethtool and SIOCGMIIPHY -- cpts_clock_mult : Numerator to convert input clock ticks into nanoseconds -- cpts_clock_shift : Denominator to convert input clock ticks into nanoseconds Optional properties: - ti,hwmods : Must be "cpgmac0" @@ -35,7 +33,11 @@ Optional properties: For example in dra72x-evm, pcf gpio has to be driven low so that cpsw slave 0 and phy data lines are connected via mux. - +- cpts_clock_mult : Numerator to convert input clock ticks into nanoseconds +- cpts_clock_shift : Denominator to convert input clock ticks into nanoseconds + Mult and shift will be calculated basing on CPTS + rftclk frequency if both cpts_clock_shift and + cpts_clock_mult properties are not provided. Slave Properties: Required properties: diff --git a/Documentation/devicetree/bindings/net/dsa/marvell.txt b/Documentation/devicetree/bindings/net/dsa/marvell.txt index 7629189398aa..b3dd6b40e0de 100644 --- a/Documentation/devicetree/bindings/net/dsa/marvell.txt +++ b/Documentation/devicetree/bindings/net/dsa/marvell.txt @@ -14,22 +14,42 @@ The properties described here are those specific to Marvell devices. Additional required and optional properties can be found in dsa.txt. Required properties: -- compatible : Should be one of "marvell,mv88e6085", +- compatible : Should be one of "marvell,mv88e6085" or + "marvell,mv88e6190" - reg : Address on the MII bus for the switch. Optional properties: - reset-gpios : Should be a gpio specifier for a reset line - +- interrupt-parent : Parent interrupt controller +- interrupts : Interrupt from the switch +- interrupt-controller : Indicates the switch is itself an interrupt + controller. This is used for the PHY interrupts. +#interrupt-cells = <2> : Controller uses two cells, number and flag +- mdio : container of PHY and devices on the switches MDIO + bus Example: mdio { #address-cells = <1>; #size-cells = <0>; + interrupt-parent = <&gpio0>; + interrupts = <27 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; switch0: switch@0 { compatible = "marvell,mv88e6085"; reg = <0>; reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; }; + mdio { + #address-cells = <1>; + #size-cells = <0>; + switch1phy0: switch1phy0@0 { + reg = <0>; + interrupt-parent = <&switch0>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + }; + }; }; diff --git a/Documentation/devicetree/bindings/net/ethernet.txt b/Documentation/devicetree/bindings/net/ethernet.txt index e1d76812419c..05150957ecfd 100644 --- a/Documentation/devicetree/bindings/net/ethernet.txt +++ b/Documentation/devicetree/bindings/net/ethernet.txt @@ -9,10 +9,26 @@ The following properties are common to the Ethernet controllers: - max-speed: number, specifies maximum speed in Mbit/s supported by the device; - max-frame-size: number, maximum transfer unit (IEEE defined MTU), rather than the maximum frame size (there's contradiction in ePAPR). -- phy-mode: string, operation mode of the PHY interface; supported values are - "mii", "gmii", "sgmii", "qsgmii", "tbi", "rev-mii", "rmii", "rgmii", "rgmii-id", - "rgmii-rxid", "rgmii-txid", "rtbi", "smii", "xgmii", "trgmii"; this is now a - de-facto standard property; +- phy-mode: string, operation mode of the PHY interface. This is now a de-facto + standard property; supported values are: + * "mii" + * "gmii" + * "sgmii" + * "qsgmii" + * "tbi" + * "rev-mii" + * "rmii" + * "rgmii" (RX and TX delays are added by the MAC when required) + * "rgmii-id" (RGMII with internal RX and TX delays provided by the PHY, the + MAC should not add the RX or TX delays in this case) + * "rgmii-rxid" (RGMII with internal RX delay provided by the PHY, the MAC + should not add an RX delay in this case) + * "rgmii-txid" (RGMII with internal TX delay provided by the PHY, the MAC + should not add an TX delay in this case) + * "rtbi" + * "smii" + * "xgmii" + * "trgmii" - phy-connection-type: the same as "phy-mode" property but described in ePAPR; - phy-handle: phandle, specifies a reference to a node representing a PHY device; this property is described in ePAPR and so preferred; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt b/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt index 75d398bb1fbb..063c02da018a 100644 --- a/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt +++ b/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt @@ -1,7 +1,12 @@ Hisilicon hix5hd2 gmac controller Required properties: -- compatible: should be "hisilicon,hix5hd2-gmac". +- compatible: should contain one of the following SoC strings: + * "hisilicon,hix5hd2-gemac" + * "hisilicon,hi3798cv200-gemac" + and one of the following version string: + * "hisilicon,hisi-gemac-v1" + * "hisilicon,hisi-gemac-v2" - reg: specifies base physical address(s) and size of the device registers. The first region is the MAC register base and size. The second region is external interface control register. @@ -12,6 +17,16 @@ Required properties: - phy-handle: see ethernet.txt [1]. - mac-address: see ethernet.txt [1]. - clocks: clock phandle and specifier pair. +- clock-names: contain the clock name "mac_core"(required) and "mac_ifc"(optional). +- resets: should contain the phandle to the MAC core reset signal(optional), + the MAC interface reset signal(optional) + and the PHY reset signal(optional). +- reset-names: contain the reset signal name "mac_core"(optional), + "mac_ifc"(optional) and "phy"(optional). +- hisilicon,phy-reset-delays-us: triplet of delays if PHY reset signal given. + The 1st cell is reset pre-delay in micro seconds. + The 2nd cell is reset pulse in micro seconds. + The 3rd cell is reset post-delay in micro seconds. - PHY subnode: inherits from phy binding [2] @@ -20,15 +35,19 @@ Required properties: Example: gmac0: ethernet@f9840000 { - compatible = "hisilicon,hix5hd2-gmac"; + compatible = "hisilicon,hi3798cv200-gemac", "hisilicon,hisi-gemac-v2"; reg = <0xf9840000 0x1000>,<0xf984300c 0x4>; interrupts = <0 71 4>; #address-cells = <1>; #size-cells = <0>; - phy-mode = "mii"; + phy-mode = "rgmii"; phy-handle = <&phy2>; mac-address = [00 00 00 00 00 00]; - clocks = <&clock HIX5HD2_MAC0_CLK>; + clocks = <&crg HISTB_ETH0_MAC_CLK>, <&crg HISTB_ETH0_MACIF_CLK>; + clock-names = "mac_core", "mac_ifc"; + resets = <&crg 0xcc 8>, <&crg 0xcc 10>, <&crg 0xcc 12>; + reset-names = "mac_core", "mac_ifc", "phy"; + hisilicon,phy-reset-delays-us = <10000 10000 30000>; phy2: ethernet-phy@2 { reg = <2>; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt index d4b7f2e49984..abfbeecbcf39 100644 --- a/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt @@ -45,6 +45,12 @@ Required properties: depends on the hardware user manual. - port-mode-offset: is offset of port mode field for each port in dsaf. Its value depends on the hardware user manual. +- mc-mac-mask: mask of multicast address, determines bit in multicast address + to set: + 1 stands for this bit will be precisely matched, TCAM will check this bit of + MAC address. + 0 stands for this bit will be fuzzy matched, TCAM won't care about this bit + of MAC address. [1] Documentation/devicetree/bindings/net/phy.txt @@ -74,10 +80,12 @@ dsaf0: dsa@c7000000 { reg = 0; phy-handle = <&phy0>; serdes-syscon = <&serdes>; + mc-mac-mask = [ff f0 00 00 00 00]; }; port@1 { reg = 1; serdes-syscon = <&serdes>; + mc-mac-mask = [ff f0 00 00 00 00]; }; }; diff --git a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt index 73be8970815e..7aa840c8768d 100644 --- a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt +++ b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt @@ -1,7 +1,10 @@ -* Marvell Armada 370 / Armada XP Ethernet Controller (NETA) +* Marvell Armada 370 / Armada XP / Armada 3700 Ethernet Controller (NETA) Required properties: -- compatible: "marvell,armada-370-neta" or "marvell,armada-xp-neta". +- compatible: could be one of the followings + "marvell,armada-370-neta" + "marvell,armada-xp-neta" + "marvell,armada-3700-neta" - reg: address and length of the register set for the device. - interrupts: interrupt for the device - phy: See ethernet.txt file in the same directory. diff --git a/Documentation/devicetree/bindings/net/marvell-orion-net.txt b/Documentation/devicetree/bindings/net/marvell-orion-net.txt index bce52b2ec55e..6fd988c84c4f 100644 --- a/Documentation/devicetree/bindings/net/marvell-orion-net.txt +++ b/Documentation/devicetree/bindings/net/marvell-orion-net.txt @@ -49,6 +49,7 @@ Optional port properties: and - phy-handle: See ethernet.txt file in the same directory. + - phy-mode: See ethernet.txt file in the same directory. or diff --git a/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt index 8516929c7251..065e8bdb957d 100644 --- a/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt +++ b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt @@ -3,7 +3,7 @@ Properties for an MDIO bus multiplexer controlled by a memory-mapped device This is a special case of a MDIO bus multiplexer. A memory-mapped device, like an FPGA, is used to control which child bus is connected. The mdio-mux node must be a child of the memory-mapped device. The driver currently only -supports devices with eight-bit registers. +supports devices with 8, 16 or 32-bit registers. Required properties in addition to the generic multiplexer properties: @@ -11,7 +11,7 @@ Required properties in addition to the generic multiplexer properties: - reg : integer, contains the offset of the register that controls the bus multiplexer. The size field in the 'reg' property is the size of - register, and must therefore be 1. + register, and must therefore be 1, 2, or 4. - mux-mask : integer, contains an eight-bit mask that specifies which bits in the register control the actual bus multiplexer. The diff --git a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt index 99c7eb0a00c8..bdefefc66594 100644 --- a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt +++ b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt @@ -6,22 +6,27 @@ Required properties: Documentation/devicetree/bindings/net/phy.txt Optional properties: -- vsc8531,vddmac : The vddmac in mV. +- vsc8531,vddmac : The vddmac in mV. Allowed values is listed + in the first row of Table 1 (below). + This property is only used in combination + with the 'edge-slowdown' property. + Default value is 3300. - vsc8531,edge-slowdown : % the edge should be slowed down relative to - the fastest possible edge time. Native sign - need not enter. + the fastest possible edge time. Edge rate sets the drive strength of the MAC - interface output signals. Changing the drive - strength will affect the edge rate of the output - signal. The goal of this setting is to help - reduce electrical emission (EMI) by being able - to reprogram drive strength and in effect slow - down the edge rate if desired. Table 1 shows the - impact to the edge rate per VDDMAC supply for each - drive strength setting. - Ref: Table:1 - Edge rate change below. - -Note: see dt-bindings/net/mscc-phy-vsc8531.h for applicable values + interface output signals. Changing the + drive strength will affect the edge rate of + the output signal. The goal of this setting + is to help reduce electrical emission (EMI) + by being able to reprogram drive strength + and in effect slow down the edge rate if + desired. + To adjust the edge-slowdown, the 'vddmac' + must be specified. Table 1 lists the + supported edge-slowdown values for a given + 'vddmac'. + Default value is 0%. + Ref: Table:1 - Edge rate change (below). Table: 1 - Edge rate change ----------------------------------------------------------------| @@ -29,23 +34,23 @@ Table: 1 - Edge rate change | | | 3300 mV 2500 mV 1800 mV 1500 mV | |---------------------------------------------------------------| -| Default Deafult Default Default | +| 0% 0% 0% 0% | | (Fastest) (recommended) (recommended) | |---------------------------------------------------------------| -| -2% -3% -5% -6% | +| 2% 3% 5% 6% | |---------------------------------------------------------------| -| -4% -6% -9% -14% | +| 4% 6% 9% 14% | |---------------------------------------------------------------| -| -7% -10% -16% -21% | +| 7% 10% 16% 21% | |(recommended) (recommended) | |---------------------------------------------------------------| -| -10% -14% -23% -29% | +| 10% 14% 23% 29% | |---------------------------------------------------------------| -| -17% -23% -35% -42% | +| 17% 23% 35% 42% | |---------------------------------------------------------------| -| -29% -37% -52% -58% | +| 29% 37% 52% 58% | |---------------------------------------------------------------| -| -53% -63% -76% -77% | +| 53% 63% 76% 77% | | (slowest) | |---------------------------------------------------------------| @@ -54,5 +59,5 @@ Example: vsc8531_0: ethernet-phy@0 { compatible = "ethernet-phy-id0007.0570"; vsc8531,vddmac = <3300>; - vsc8531,edge-slowdown = <21>; + vsc8531,edge-slowdown = <7>; }; diff --git a/Documentation/devicetree/bindings/net/oxnas-dwmac.txt b/Documentation/devicetree/bindings/net/oxnas-dwmac.txt new file mode 100644 index 000000000000..df0534e2eda1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/oxnas-dwmac.txt @@ -0,0 +1,39 @@ +* Oxford Semiconductor OXNAS DWMAC Ethernet controller + +The device inherits all the properties of the dwmac/stmmac devices +described in the file stmmac.txt in the current directory with the +following changes. + +Required properties on all platforms: + +- compatible: For the OX820 SoC, it should be : + - "oxsemi,ox820-dwmac" to select glue + - "snps,dwmac-3.512" to select IP version. + +- clocks: Should contain phandles to the following clocks +- clock-names: Should contain the following: + - "stmmaceth" for the host clock - see stmmac.txt + - "gmac" for the peripheral gate clock + +- oxsemi,sys-ctrl: a phandle to the system controller syscon node + +Example : + +etha: ethernet@40400000 { + compatible = "oxsemi,ox820-dwmac", "snps,dwmac-3.512"; + reg = <0x40400000 0x2000>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq", "eth_wake_irq"; + mac-address = [000000000000]; /* Filled in by U-Boot */ + phy-mode = "rgmii"; + + clocks = <&stdclk CLK_820_ETHA>, <&gmacclk>; + clock-names = "gmac", "stmmaceth"; + resets = <&reset RESET_MAC>; + + /* Regmap for sys registers */ + oxsemi,sys-ctrl = <&sys>; + + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt index bc1c3c8bf8fa..54749b60a466 100644 --- a/Documentation/devicetree/bindings/net/phy.txt +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -35,6 +35,12 @@ Optional Properties: - broken-turn-around: If set, indicates the PHY device does not correctly release the turn around line low at the end of a MDIO transaction. +- enet-phy-lane-swap: If set, indicates the PHY will swap the TX/RX lanes to + compensate for the board being designed with the lanes swapped. + +- eee-broken-modes: Bits to clear in the MDIO_AN_EEE_ADV register to + disable EEE broken modes. + Example: ethernet-phy@0 { diff --git a/Documentation/devicetree/bindings/net/smsc-lan91c111.txt b/Documentation/devicetree/bindings/net/smsc-lan91c111.txt index e77e167593db..309e37eb7c7c 100644 --- a/Documentation/devicetree/bindings/net/smsc-lan91c111.txt +++ b/Documentation/devicetree/bindings/net/smsc-lan91c111.txt @@ -13,3 +13,5 @@ Optional properties: 16-bit access only. - power-gpios: GPIO to control the PWRDWN pin - reset-gpios: GPIO to control the RESET pin +- pxa-u16-align4 : Boolean, put in place the workaround the force all + u16 writes to be 32 bits aligned diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index 41b49e6075f5..128da752fec9 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -1,7 +1,7 @@ * STMicroelectronics 10/100/1000 Ethernet driver (GMAC) Required properties: -- compatible: Should be "snps,dwmac-<ip_version>" "snps,dwmac" +- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac" For backwards compatibility: "st,spear600-gmac" is also supported. - reg: Address and length of the register set for the device - interrupt-parent: Should be the phandle for the interrupt controller @@ -34,7 +34,13 @@ Optional properties: platforms. - tx-fifo-depth: See ethernet.txt file in the same directory - rx-fifo-depth: See ethernet.txt file in the same directory -- snps,pbl Programmable Burst Length +- snps,pbl Programmable Burst Length (tx and rx) +- snps,txpbl Tx Programmable Burst Length. Only for GMAC and newer. + If set, DMA tx will use this value rather than snps,pbl. +- snps,rxpbl Rx Programmable Burst Length. Only for GMAC and newer. + If set, DMA rx will use this value rather than snps,pbl. +- snps,no-pbl-x8 Don't multiply the pbl/txpbl/rxpbl values by 8. + For core rev < 3.50, don't multiply the values by 4. - snps,aal Address-Aligned Beats - snps,fixed-burst Program the DMA to use the fixed burst mode - snps,mixed-burst Program the DMA to use the mixed burst mode @@ -50,6 +56,8 @@ Optional properties: - snps,ps-speed: port selection speed that can be passed to the core when PCS is supported. For example, this is used in case of SGMII and MAC2MAC connection. +- snps,tso: this enables the TSO feature otherwise it will be managed by + MAC HW capability register. Only for GMAC4 and newer. - AXI BUS Mode parameters: below the list of all the parameters to program the AXI register inside the DMA module: - snps,lpi_en: enable Low Power Interface @@ -62,8 +70,6 @@ Optional properties: - snps,fb: fixed-burst - snps,mb: mixed-burst - snps,rb: rebuild INCRx Burst - - snps,tso: this enables the TSO feature otherwise it will be managed by - MAC HW capability register. - mdio: with compatible = "snps,dwmac-mdio", create and register mdio bus. Examples: diff --git a/Documentation/devicetree/bindings/net/ti,dp83867.txt b/Documentation/devicetree/bindings/net/ti,dp83867.txt index 5d21141a68b5..85bf945b898f 100644 --- a/Documentation/devicetree/bindings/net/ti,dp83867.txt +++ b/Documentation/devicetree/bindings/net/ti,dp83867.txt @@ -9,6 +9,18 @@ Required properties: - ti,fifo-depth - Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h for applicable values +Optional property: + - ti,min-output-impedance - MAC Interface Impedance control to set + the programmable output impedance to + minimum value (35 ohms). + - ti,max-output-impedance - MAC Interface Impedance control to set + the programmable output impedance to + maximum value (70 ohms). + +Note: ti,min-output-impedance and ti,max-output-impedance are mutually + exclusive. When both properties are present ti,max-output-impedance + takes precedence. + Default child nodes are standard Ethernet PHY device nodes as described in Documentation/devicetree/bindings/net/phy.txt diff --git a/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt b/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt index c421aba0a5bc..980b16df74c3 100644 --- a/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt +++ b/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt @@ -1,8 +1,8 @@ -Marvell 8897/8997 (sd8897/sd8997) SDIO devices +Marvell 8897/8997 (sd8897/sd8997/pcie8997) SDIO/PCIE devices ------ -This node provides properties for controlling the marvell sdio wireless device. -The node is expected to be specified as a child node to the SDIO controller that +This node provides properties for controlling the Marvell SDIO/PCIE wireless device. +The node is expected to be specified as a child node to the SDIO/PCIE controller that connects the device to the system. Required properties: @@ -10,6 +10,8 @@ Required properties: - compatible : should be one of the following: * "marvell,sd8897" * "marvell,sd8997" + * "pci11ab,2b42" + * "pci1b4b,2b42" Optional properties: diff --git a/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt b/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt new file mode 100644 index 000000000000..b7396c8c271c --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt @@ -0,0 +1,48 @@ +* Qualcomm Atheros ath9k wireless devices + +This node provides properties for configuring the ath9k wireless device. The +node is expected to be specified as a child node of the PCI controller to +which the wireless chip is connected. + +Required properties: +- compatible: For PCI and PCIe devices this should be an identifier following + the format as defined in "PCI Bus Binding to Open Firmware" + Revision 2.1. One of the possible formats is "pciVVVV,DDDD" + where VVVV is the PCI vendor ID and DDDD is PCI device ID. + Typically QCA's PCI vendor ID 168c is used while the PCI device + ID depends on the chipset - see the following (possibly + incomplete) list: + - 0023 for AR5416 + - 0024 for AR5418 + - 0027 for AR9160 + - 0029 for AR9220 and AR9223 + - 002a for AR9280 and AR9283 + - 002b for AR9285 + - 002c for AR2427 + - 002d for AR9227 + - 002e for AR9287 + - 0030 for AR9380, AR9381 and AR9382 + - 0032 for AR9485 + - 0033 for AR9580 and AR9590 + - 0034 for AR9462 + - 0036 for AR9565 + - 0037 for AR9485 +- reg: Address and length of the register set for the device. + +Optional properties: +- qca,no-eeprom: Indicates that there is no physical EEPROM connected to the + ath9k wireless chip (in this case the calibration / + EEPROM data will be loaded from userspace using the + kernel firmware loader). +- mac-address: See ethernet.txt in the parent directory +- local-mac-address: See ethernet.txt in the parent directory + + +In this example, the node is defined as child node of the PCI controller: +&pci0 { + wifi@168c,002d { + compatible = "pci168c,002d"; + reg = <0x7000 0 0 0 0x1000>; + qca,no-eeprom; + }; +}; diff --git a/Documentation/devicetree/bindings/nvmem/brcm,ocotp.txt b/Documentation/devicetree/bindings/nvmem/brcm,ocotp.txt new file mode 100644 index 000000000000..6462e12d8de6 --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/brcm,ocotp.txt @@ -0,0 +1,17 @@ +Broadcom OTP memory controller + +Required Properties: +- compatible: "brcm,ocotp" for the first generation Broadcom OTPC which is used + in Cygnus and supports 32 bit read/write. Use "brcm,ocotp-v2" for the second + generation Broadcom OTPC which is used in SoC's such as Stingray and supports + 64-bit read/write. +- reg: Base address of the OTP controller. +- brcm,ocotp-size: Amount of memory available, in 32 bit words + +Example: + +otp: otp@0301c800 { + compatible = "brcm,ocotp"; + reg = <0x0301c800 0x2c>; + brcm,ocotp-size = <2048>; +}; diff --git a/Documentation/devicetree/bindings/nvmem/lpc1850-otp.txt b/Documentation/devicetree/bindings/nvmem/lpc1850-otp.txt new file mode 100644 index 000000000000..853b6a754644 --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/lpc1850-otp.txt @@ -0,0 +1,20 @@ +* NXP LPC18xx OTP memory + +Internal OTP (One Time Programmable) memory for NXP LPC18xx/43xx devices. + +Required properties: + - compatible: Should be "nxp,lpc1850-otp" + - reg: Must contain an entry with the physical base address and length + for each entry in reg-names. + - address-cells: must be set to 1. + - size-cells: must be set to 1. + +See nvmem.txt for more information. + +Example: + otp: otp@40045000 { + compatible = "nxp,lpc1850-otp"; + reg = <0x40045000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/opp/opp.txt b/Documentation/devicetree/bindings/opp/opp.txt index ee91cbdd95ee..9f5ca4457b5f 100644 --- a/Documentation/devicetree/bindings/opp/opp.txt +++ b/Documentation/devicetree/bindings/opp/opp.txt @@ -86,8 +86,14 @@ Optional properties: Single entry is for target voltage and three entries are for <target min max> voltages. - Entries for multiple regulators must be present in the same order as - regulators are specified in device's DT node. + Entries for multiple regulators shall be provided in the same field separated + by angular brackets <>. The OPP binding doesn't provide any provisions to + relate the values to their power supplies or the order in which the supplies + need to be configured and that is left for the implementation specific + binding. + + Entries for all regulators shall be of the same size, i.e. either all use a + single value or triplets. - opp-microvolt-<name>: Named opp-microvolt property. This is exactly similar to the above opp-microvolt property, but allows multiple voltage ranges to be @@ -104,10 +110,13 @@ Optional properties: Should only be set if opp-microvolt is set for the OPP. - Entries for multiple regulators must be present in the same order as - regulators are specified in device's DT node. If this property isn't required - for few regulators, then this should be marked as zero for them. If it isn't - required for any regulator, then this property need not be present. + Entries for multiple regulators shall be provided in the same field separated + by angular brackets <>. If current values aren't required for a regulator, + then it shall be filled with 0. If current values aren't required for any of + the regulators, then this field is not required. The OPP binding doesn't + provide any provisions to relate the values to their power supplies or the + order in which the supplies need to be configured and that is left for the + implementation specific binding. - opp-microamp-<name>: Named opp-microamp property. Similar to opp-microvolt-<name> property, but for microamp instead. @@ -386,10 +395,12 @@ Example 4: Handling multiple regulators / { cpus { cpu@0 { - compatible = "arm,cortex-a7"; + compatible = "vendor,cpu-type"; ... - cpu-supply = <&cpu_supply0>, <&cpu_supply1>, <&cpu_supply2>; + vcc0-supply = <&cpu_supply0>; + vcc1-supply = <&cpu_supply1>; + vcc2-supply = <&cpu_supply2>; operating-points-v2 = <&cpu0_opp_table>; }; }; diff --git a/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt b/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt index 01b88f4e0d5b..b8e48b4762b2 100644 --- a/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt +++ b/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt @@ -1,10 +1,17 @@ * Broadcom iProc PCIe controller with the platform bus interface Required properties: -- compatible: Must be "brcm,iproc-pcie" for PAXB, or "brcm,iproc-pcie-paxc" - for PAXC. PAXB-based root complex is used for external endpoint devices. - PAXC-based root complex is connected to emulated endpoint devices - internal to the ASIC +- compatible: + "brcm,iproc-pcie" for the first generation of PAXB based controller, +used in SoCs including NSP, Cygnus, NS2, and Pegasus + "brcm,iproc-pcie-paxb-v2" for the second generation of PAXB-based +controllers, used in Stingray + "brcm,iproc-pcie-paxc" for the first generation of PAXC based +controller, used in NS2 + "brcm,iproc-pcie-paxc-v2" for the second generation of PAXC based +controller, used in Stingray + PAXB-based root complex is used for external endpoint devices. PAXC-based +root complex is connected to emulated endpoint devices internal to the ASIC - reg: base address and length of the PCIe controller I/O register space - #interrupt-cells: set to <1> - interrupt-map-mask and interrupt-map, standard PCI properties to define the @@ -19,6 +26,10 @@ Required properties: Optional properties: - phys: phandle of the PCIe PHY device - phy-names: must be "pcie-phy" +- dma-coherent: present if DMA operations are coherent +- dma-ranges: Some PAXB-based root complexes do not have inbound mapping done + by the ASIC after power on reset. In this case, SW is required to configure +the mapping, based on inbound memory regions specified by this property. - brcm,pcie-ob: Some iProc SoCs do not have the outbound address mapping done by the ASIC after power on reset. In this case, SW needs to configure it @@ -29,11 +40,6 @@ effective: Required: - brcm,pcie-ob-axi-offset: The offset from the AXI address to the internal address used by the iProc PCIe core (not the PCIe address) -- brcm,pcie-ob-window-size: The outbound address mapping window size (in MB) - -Optional: -- brcm,pcie-ob-oarr-size: Some iProc SoCs need the OARR size bit to be set to -increase the outbound window size MSI support (optional): @@ -41,10 +47,19 @@ For older platforms without MSI integrated in the GIC, iProc PCIe core provides an event queue based MSI support. The iProc MSI uses host memories to store MSI posted writes in the event queues -- msi-parent: Link to the device node of the MSI controller. On newer iProc -platforms, the MSI controller may be gicv2m or gicv3-its. On older iProc -platforms without MSI support in its interrupt controller, one may use the -event queue based MSI support integrated within the iProc PCIe core. +On newer iProc platforms, gicv2m or gicv3-its based MSI support should be used + +- msi-map: Maps a Requester ID to an MSI controller and associated MSI +sideband data + +- msi-parent: Link to the device node of the MSI controller, used when no MSI +sideband data is passed between the iProc PCIe controller and the MSI +controller + +Refer to the following binding documents for more detailed description on +the use of 'msi-map' and 'msi-parent': + Documentation/devicetree/bindings/pci/pci-msi.txt + Documentation/devicetree/bindings/interrupt-controller/msi.txt When the iProc event queue based MSI is used, one needs to define the following properties in the MSI device node: @@ -80,9 +95,7 @@ Example: phy-names = "pcie-phy"; brcm,pcie-ob; - brcm,pcie-ob-oarr-size; brcm,pcie-ob-axi-offset = <0x00000000>; - brcm,pcie-ob-window-size = <256>; msi-parent = <&msi0>; diff --git a/Documentation/devicetree/bindings/pci/layerscape-pci.txt b/Documentation/devicetree/bindings/pci/layerscape-pci.txt index 41e9f55a1467..ee1c72d5162e 100644 --- a/Documentation/devicetree/bindings/pci/layerscape-pci.txt +++ b/Documentation/devicetree/bindings/pci/layerscape-pci.txt @@ -15,6 +15,7 @@ Required properties: - compatible: should contain the platform identifier such as: "fsl,ls1021a-pcie", "snps,dw-pcie" "fsl,ls2080a-pcie", "fsl,ls2085a-pcie", "snps,dw-pcie" + "fsl,ls1046a-pcie" - reg: base addresses and lengths of the PCIe controller - interrupts: A list of interrupt outputs of the controller. Must contain an entry for each entry in the interrupt-names property. diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt index b8cc395fffea..982a74ea6df9 100644 --- a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt @@ -110,6 +110,20 @@ Power supplies for Tegra124: - avdd-pll-erefe-supply: Power supply for PLLE (shared with USB3). Must supply 1.05 V. +Power supplies for Tegra210: +- Required: + - avdd-pll-uerefe-supply: Power supply for PLLE (shared with USB3). Must + supply 1.05 V. + - hvddio-pex-supply: High-voltage supply for PCIe I/O and PCIe output + clocks. Must supply 1.8 V. + - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + - dvdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must + supply 1.05 V. + - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3). + Must supply 3.3 V. + - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must + supply 1.8 V. + Root ports are defined as subnodes of the PCIe controller node. Required properties: @@ -436,3 +450,99 @@ Board DTS: status = "okay"; }; }; + +Tegra210: +--------- + +SoC DTSI: + + pcie-controller@01003000 { + compatible = "nvidia,tegra210-pcie"; + device_type = "pci"; + reg = <0x0 0x01003000 0x0 0x00000800 /* PADS registers */ + 0x0 0x01003800 0x0 0x00000800 /* AFI registers */ + 0x0 0x02000000 0x0 0x10000000>; /* configuration space */ + reg-names = "pads", "afi", "cs"; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */ + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + + bus-range = <0x00 0xff>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x82000000 0 0x01000000 0x0 0x01000000 0 0x00001000 /* port 0 configuration space */ + 0x82000000 0 0x01001000 0x0 0x01001000 0 0x00001000 /* port 1 configuration space */ + 0x81000000 0 0x0 0x0 0x12000000 0 0x00010000 /* downstream I/O (64 KiB) */ + 0x82000000 0 0x13000000 0x0 0x13000000 0 0x0d000000 /* non-prefetchable memory (208 MiB) */ + 0xc2000000 0 0x20000000 0x0 0x20000000 0 0x20000000>; /* prefetchable memory (512 MiB) */ + + clocks = <&tegra_car TEGRA210_CLK_PCIE>, + <&tegra_car TEGRA210_CLK_AFI>, + <&tegra_car TEGRA210_CLK_PLL_E>, + <&tegra_car TEGRA210_CLK_CML0>; + clock-names = "pex", "afi", "pll_e", "cml"; + resets = <&tegra_car 70>, + <&tegra_car 72>, + <&tegra_car 74>; + reset-names = "pex", "afi", "pcie_x"; + status = "disabled"; + + pci@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x01000000 0 0x1000>; + reg = <0x000800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <4>; + }; + + pci@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x01001000 0 0x1000>; + reg = <0x001000 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <1>; + }; + }; + +Board DTS: + + pcie-controller@01003000 { + status = "okay"; + + avdd-pll-uerefe-supply = <&avdd_1v05_pll>; + hvddio-pex-supply = <&vdd_1v8>; + dvddio-pex-supply = <&vdd_pex_1v05>; + dvdd-pex-pll-supply = <&vdd_pex_1v05>; + hvdd-pex-pll-e-supply = <&vdd_1v8>; + vddio-pex-ctl-supply = <&vdd_1v8>; + + pci@1,0 { + phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-0}>, + <&{/padctl@7009f000/pads/pcie/lanes/pcie-1}>, + <&{/padctl@7009f000/pads/pcie/lanes/pcie-2}>, + <&{/padctl@7009f000/pads/pcie/lanes/pcie-3}>; + phy-names = "pcie-0", "pcie-1", "pcie-2", "pcie-3"; + status = "okay"; + }; + + pci@2,0 { + phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-4}>; + phy-names = "pcie-0"; + status = "okay"; + }; + }; diff --git a/Documentation/devicetree/bindings/pci/pci.txt b/Documentation/devicetree/bindings/pci/pci.txt index 08dcfad09f8d..50f9e2ca5b13 100644 --- a/Documentation/devicetree/bindings/pci/pci.txt +++ b/Documentation/devicetree/bindings/pci/pci.txt @@ -18,3 +18,9 @@ driver implementation may support the following properties: host bridges in the system, otherwise potentially conflicting domain numbers may be assigned to root buses behind different host bridges. The domain number for each host bridge in the system must be unique. +- max-link-speed: + If present this property specifies PCI gen for link capability. Host + drivers could add this as a strategy to avoid unnecessary operation for + unsupported link speed, for instance, trying to do training for + unsupported link speed, etc. Must be '4' for gen4, '3' for gen3, '2' + for gen2, and '1' for gen1. Any other values are invalid. diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt index 4059a6f89bc1..e15f9b19901f 100644 --- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt @@ -7,6 +7,7 @@ - "qcom,pcie-ipq8064" for ipq8064 - "qcom,pcie-apq8064" for apq8064 - "qcom,pcie-apq8084" for apq8084 + - "qcom,pcie-msm8996" for msm8996 or apq8096 - reg: Usage: required @@ -92,6 +93,17 @@ - "aux" Auxiliary (AUX) clock - "bus_master" Master AXI clock - "bus_slave" Slave AXI clock + +- clock-names: + Usage: required for msm8996/apq8096 + Value type: <stringlist> + Definition: Should contain the following entries + - "pipe" Pipe Clock driving internal logic + - "aux" Auxiliary (AUX) clock + - "cfg" Configuration clock + - "bus_master" Master AXI clock + - "bus_slave" Slave AXI clock + - resets: Usage: required Value type: <prop-encoded-array> @@ -115,7 +127,7 @@ - "core" Core reset - power-domains: - Usage: required for apq8084 + Usage: required for apq8084 and msm8996/apq8096 Value type: <prop-encoded-array> Definition: A phandle and power domain specifier pair to the power domain which is responsible for collapsing diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt index 6cf99690eef9..eee518db90b9 100644 --- a/Documentation/devicetree/bindings/pci/rcar-pci.txt +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -7,6 +7,7 @@ compatible: "renesas,pcie-r8a7779" for the R8A7779 SoC; "renesas,pcie-r8a7793" for the R8A7793 SoC; "renesas,pcie-r8a7795" for the R8A7795 SoC; "renesas,pcie-rcar-gen2" for a generic R-Car Gen2 compatible device. + "renesas,pcie-rcar-gen3" for a generic R-Car Gen3 compatible device. When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt index ba67b39939c1..71aeda1ca055 100644 --- a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt +++ b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt @@ -26,13 +26,16 @@ Required properties: - "sys" - "legacy" - "client" -- resets: Must contain five entries for each entry in reset-names. +- resets: Must contain seven entries for each entry in reset-names. See ../reset/reset.txt for details. - reset-names: Must include the following names - "core" - "mgmt" - "mgmt-sticky" - "pipe" + - "pm" + - "aclk" + - "pclk" - pinctrl-names : The pin control state names - pinctrl-0: The "default" pinctrl state - #interrupt-cells: specifies the number of cells needed to encode an @@ -86,8 +89,10 @@ pcie0: pcie@f8000000 { reg = <0x0 0xf8000000 0x0 0x2000000>, <0x0 0xfd000000 0x0 0x1000000>; reg-names = "axi-base", "apb-base"; resets = <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>, - <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>; - reset-names = "core", "mgmt", "mgmt-sticky", "pipe"; + <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE> , + <&cru SRST_PCIE_PM>, <&cru SRST_P_PCIE>, <&cru SRST_A_PCIE>; + reset-names = "core", "mgmt", "mgmt-sticky", "pipe", + "pm", "pclk", "aclk"; phys = <&pcie_phy>; phy-names = "pcie-phy"; pinctrl-names = "default"; diff --git a/Documentation/devicetree/bindings/phy/meson-usb2-phy.txt b/Documentation/devicetree/bindings/phy/meson8b-usb2-phy.txt index 9da5ea234154..5fa73b9d20f5 100644 --- a/Documentation/devicetree/bindings/phy/meson-usb2-phy.txt +++ b/Documentation/devicetree/bindings/phy/meson8b-usb2-phy.txt @@ -1,4 +1,4 @@ -* Amlogic USB2 PHY +* Amlogic Meson8b and GXBB USB2 PHY Required properties: - compatible: Depending on the platform this should be one of: @@ -16,10 +16,10 @@ Optional properties: Example: -usb0_phy: usb_phy@0 { +usb0_phy: usb-phy@c0000000 { compatible = "amlogic,meson-gxbb-usb2-phy"; #phy-cells = <0>; - reg = <0x0 0x0 0x0 0x20>; + reg = <0x0 0xc0000000 0x0 0x20>; resets = <&reset RESET_USB_OTG>; clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB0>; clock-names = "usb_general", "usb"; diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index 1685821eea41..de1378b4efad 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -28,6 +28,20 @@ Required properties: - reg: Should contain the register physical address and length for the pin controller. +- clocks: phandle to the clocks feeding the pin controller: + - "apb": the gated APB parent clock + - "hosc": the high frequency oscillator in the system + - "losc": the low frequency oscillator in the system + +Note: For backward compatibility reasons, the hosc and losc clocks are only +required if you need to use the optional input-debounce property. Any new +device tree should set them. + +Optional properties: + - input-debounce: Array of debouncing periods in microseconds. One period per + irq bank found in the controller. 0 if no setup required. + + Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices. @@ -37,6 +51,22 @@ pins it needs, and how they should be configured, with regard to muxer configuration, drive strength and pullups. If one of these options is not set, its actual value will be unspecified. +This driver supports the generic pin multiplexing and configuration +bindings. For details on each properties, you can refer to +./pinctrl-bindings.txt. + +Required sub-node properties: + - pins + - function + +Optional sub-node properties: + - bias-disable + - bias-pull-up + - bias-pull-down + - drive-strength + +*** Deprecated pin configuration and multiplexing binding + Required subnode-properties: - allwinner,pins: List of strings containing the pin name. diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt index b7a93e80a302..9a8a45d9d8ab 100644 --- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt @@ -98,6 +98,8 @@ DRIVE_STRENGTH (3 << 5): indicate the drive strength of the pin using the 01 - Low 10 - Medium 11 - High +OUTPUT (1 << 7): indicate this pin need to be configured as an output. +OUTPUT_VAL (1 << 8): output val (1 = high, 0 = low) DEBOUNCE (1 << 16): indicate this pin needs debounce. DEBOUNCE_VAL (0x3fff << 17): debounce value. diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt index fe7fe0b03cfb..2392557ede27 100644 --- a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt @@ -7,6 +7,8 @@ Required properties for the root node: "amlogic,meson8b-aobus-pinctrl" "amlogic,meson-gxbb-periphs-pinctrl" "amlogic,meson-gxbb-aobus-pinctrl" + "amlogic,meson-gxl-periphs-pinctrl" + "amlogic,meson-gxl-aobus-pinctrl" - reg: address and size of registers controlling irq functionality === GPIO sub-nodes === diff --git a/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt index d6074321f730..09e81a95bbfd 100644 --- a/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt @@ -9,7 +9,7 @@ used for a specific device or function. This node represents configurations of pins, optional function, and optional mux related configuration. Required properties for pin controller node: - - compatible: "oxsemi,ox810se-pinctrl" + - compatible: "oxsemi,ox810se-pinctrl" or "oxsemi,ox820-pinctrl" - oxsemi,sys-ctrl: a phandle to the system controller syscon node Required properties for pin configuration sub-nodes: diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt index b73c96d24f59..bf3f7b014724 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt @@ -97,6 +97,11 @@ For example: }; == Pin controller devices == +Required properties: See the pin controller driver specific documentation + +Optional properties: +#pinctrl-cells: Number of pin control cells in addition to the index within the + pin controller device instance Pin controller devices should contain the pin configuration nodes that client devices reference. @@ -119,7 +124,8 @@ For example: The contents of each of those pin configuration child nodes is defined entirely by the binding for the individual pin controller device. There -exists no common standard for this content. +exists no common standard for this content. The pinctrl framework only +provides generic helper bindings that the pin controller driver can use. The pin configuration nodes need not be direct children of the pin controller device; they may be grandchildren, for example. Whether this is legal, and @@ -156,6 +162,42 @@ state_2_node_a { pins = "mfio29", "mfio30"; }; +Optionally an altenative binding can be used if more suitable depending on the +pin controller hardware. For hardaware where there is a large number of identical +pin controller instances, naming each pin and function can easily become +unmaintainable. This is especially the case if the same controller is used for +different pins and functions depending on the SoC revision and packaging. + +For cases like this, the pin controller driver may use pinctrl-pin-array helper +binding with a hardware based index and a number of pin configuration values: + +pincontroller { + ... /* Standard DT properties for the device itself elided */ + #pinctrl-cells = <2>; + + state_0_node_a { + pinctrl-pin-array = < + 0 A_DELAY_PS(0) G_DELAY_PS(120) + 4 A_DELAY_PS(0) G_DELAY_PS(360) + ... + >; + }; + ... +}; + +Above #pinctrl-cells specifies the number of value cells in addition to the +index of the registers. This is similar to the interrupts-extended binding with +one exception. There is no need to specify the phandle for each entry as that +is already known as the defined pins are always children of the pin controller +node. Further having the phandle pointing to another pin controller would not +currently work as the pinctrl framework uses named modes to group pins for each +pin control device. + +The index for pinctrl-pin-array must relate to the hardware for the pinctrl +registers, and must not be a virtual index of pin instances. The reason for +this is to avoid mapping of the index in the dts files and the pin controller +driver as it can change. + == Generic pin configuration node content == Many data items that are represented in a pin configuration node are common diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-palmas.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-palmas.txt index caf297bee1fb..c28d4eb83b76 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-palmas.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-palmas.txt @@ -35,6 +35,15 @@ Optional properties: - ti,palmas-enable-dvfs2: Enable DVFS2. Configure pins for DVFS2 mode. Selection primary or secondary function associated to GPADC_START and SYSEN2 pin/pad for DVFS2 interface +- ti,palmas-override-powerhold: This is applicable for PMICs for which + GPIO7 is configured in POWERHOLD mode which has higher priority + over DEV_ON bit and keeps the PMIC supplies on even after the DEV_ON + bit is turned off. This property enables driver to over ride the + POWERHOLD value to GPIO7 so as to turn off the PMIC in power off + scenarios. So for GPIO7 if ti,palmas-override-powerhold is set + then the GPIO_7 field should never be muxed to anything else. + It should be set to POWERHOLD by default and only in case of + power off scenarios the driver will over ride the mux value. This binding uses the following generic properties as defined in pinctrl-bindings.txt: diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt new file mode 100644 index 000000000000..bf76867168e9 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt @@ -0,0 +1,74 @@ +SEMTECH SX150x GPIO expander bindings + +Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and +../interrupt-controller/interrupts.txt for generic information regarding +pin controller, GPIO, and interrupt bindings. + +Required properties: +- compatible: should be one of : + "semtech,sx1501q", + "semtech,sx1502q", + "semtech,sx1503q", + "semtech,sx1504q", + "semtech,sx1505q", + "semtech,sx1506q", + "semtech,sx1507q", + "semtech,sx1508q", + "semtech,sx1509q". + +- reg: The I2C slave address for this device. + +- #gpio-cells: Should be 2. The first cell is the GPIO number and the + second cell is used to specify optional parameters: + bit 0: polarity (0: normal, 1: inverted) + +- gpio-controller: Marks the device as a GPIO controller. + +Optional properties : +- interrupt-parent: phandle of the parent interrupt controller. + +- interrupts: Interrupt specifier for the controllers interrupt. + +- interrupt-controller: Marks the device as a interrupt controller. + +- semtech,probe-reset: Will trigger a reset of the GPIO expander on probe, + only for sx1507q, sx1508q and sx1509q + +The GPIO expander can optionally be used as an interrupt controller, in +which case it uses the default two cell specifier. + +Required properties for pin configuration sub-nodes: + - pins: List of pins to which the configuration applies. + +Optional properties for pin configuration sub-nodes: +---------------------------------------------------- + - bias-disable: disable any pin bias, except the OSCIO pin + - bias-pull-up: pull up the pin, except the OSCIO pin + - bias-pull-down: pull down the pin, except the OSCIO pin + - bias-pull-pin-default: use pin-default pull state, except the OSCIO pin + - drive-push-pull: drive actively high and low + - drive-open-drain: drive with open drain only for sx1507q, sx1508q and sx1509q and except the OSCIO pin + - output-low: set the pin to output mode with low level + - output-high: set the pin to output mode with high level + +Example: + + i2c0gpio-expander@20{ + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "semtech,sx1506q"; + reg = <0x20>; + interrupt-parent = <&gpio_1>; + interrupts = <16 0>; + + gpio-controller; + interrupt-controller; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio1_cfg_pins>; + + gpio1_cfg_pins: gpio1-cfg { + pins = "gpio1"; + bias-pull-up; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8994-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8994-pinctrl.txt new file mode 100644 index 000000000000..13cd629f896e --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8994-pinctrl.txt @@ -0,0 +1,177 @@ +Qualcomm MSM8994 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +MSM8994 platform. + +- compatible: + Usage: required + Value type: <string> + Definition: Should contain one of: + "qcom,msm8992-pinctrl", + "qcom,msm8994-pinctrl". + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the TLMM register space. + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: <none> + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/interrupt-controller/irq.h> + +- gpio-controller: + Usage: required + Value type: <none> + Definition: identifies this node as a gpio controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/gpio/gpio.h> + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. + + Valid pins are: + gpio0-gpio145 + Supports mux, bias and drive-strength + + sdc1_clk, sdc1_cmd, sdc1_data sdc1_rclk, sdc2_clk, + sdc2_cmd, sdc2_data + Supports bias and drive-strength + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Functions are only valid for gpio pins. + Valid values are: + + audio_ref_clk, blsp_i2c1, blsp_i2c2, blsp_i2c3, blsp_i2c4, blsp_i2c5, + blsp_i2c6, blsp_i2c7, blsp_i2c8, blsp_i2c9, blsp_i2c10, blsp_i2c11, + blsp_i2c12, blsp_spi1, blsp_spi1_cs1, blsp_spi1_cs2, blsp_spi1_cs3, + blsp_spi2, blsp_spi2_cs1, blsp_spi2_cs2, blsp_spi2_cs3, blsp_spi3, + blsp_spi4, blsp_spi5, blsp_spi6, blsp_spi7, blsp_spi8, blsp_spi9, + blsp_spi10, blsp_spi10_cs1, blsp_spi10_cs2, blsp_spi10_cs3, blsp_spi11, + blsp_spi12, blsp_uart1, blsp_uart2, blsp_uart3, blsp_uart4, blsp_uart5, + blsp_uart6, blsp_uart7, blsp_uart8, blsp_uart9, blsp_uart10, blsp_uart11, + blsp_uart12, blsp_uim1, blsp_uim2, blsp_uim3, blsp_uim4, blsp_uim5, + blsp_uim6, blsp_uim7, blsp_uim8, blsp_uim9, blsp_uim10, blsp_uim11, + blsp_uim12, blsp11_i2c_scl_b, blsp11_i2c_sda_b, blsp11_uart_rx_b, + blsp11_uart_tx_b, cam_mclk0, cam_mclk1, cam_mclk2, cam_mclk3, + cci_async_in0, cci_async_in1, cci_async_in2, cci_i2c0, cci_i2c1, + cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4, + gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a, gcc_gp2_clk_b, gcc_gp3_clk_a, + gcc_gp3_clk_b, gp_mn, gp_pdm0, gp_pdm1, gp_pdm2, gp0_clk, + gp1_clk, gps_tx, gsm_tx, hdmi_cec, hdmi_ddc, hdmi_hpd, hdmi_rcv, + mdp_vsync, mss_lte, nav_pps, nav_tsync, qdss_cti_trig_in_a, + qdss_cti_trig_in_b, qdss_cti_trig_in_c, qdss_cti_trig_in_d, + qdss_cti_trig_out_a, qdss_cti_trig_out_b, qdss_cti_trig_out_c, + qdss_cti_trig_out_d, qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, + qdss_tracectl_b, qdss_tracedata_a, qdss_tracedata_b, qua_mi2s, pci_e0, + pci_e1, pri_mi2s, sdc4, sec_mi2s, slimbus, spkr_i2s, ter_mi2s, tsif1, + tsif2, uim_batt_alarm, uim1, uim2, uim3, uim4, gpio + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull down. + +- bias-pull-up: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull up. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + Not valid for sdc pins. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + Not valid for sdc pins. + +- drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + msmgpio: pinctrl@fd510000 { + compatible = "qcom,msm8994-pinctrl"; + reg = <0xfd510000 0x4000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + + blsp1_uart2_default: blsp1_uart2_default { + pinmux { + pins = "gpio4", "gpio5"; + function = "blsp_uart2"; + }; + pinconf { + pins = "gpio4", "gpio5"; + drive-strength = <16>; + bias-disable; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt index c68b9554561f..4722bc61a1a2 100644 --- a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt @@ -19,10 +19,11 @@ The pins are grouped into up to 5 individual pin banks which need to be defined as gpio sub-nodes of the pinmux controller. Required properties for iomux controller: - - compatible: one of "rockchip,rk2928-pinctrl", "rockchip,rk3066a-pinctrl" - "rockchip,rk3066b-pinctrl", "rockchip,rk3188-pinctrl" - "rockchip,rk3228-pinctrl", "rockchip,rk3288-pinctrl" - "rockchip,rk3368-pinctrl", "rockchip,rk3399-pinctrl" + - compatible: one of "rockchip,rk1108-pinctrl", "rockchip,rk2928-pinctrl" + "rockchip,rk3066a-pinctrl", "rockchip,rk3066b-pinctrl" + "rockchip,rk3188-pinctrl", "rockchip,rk3228-pinctrl" + "rockchip,rk3288-pinctrl", "rockchip,rk3368-pinctrl" + "rockchip,rk3399-pinctrl" - rockchip,grf: phandle referencing a syscon providing the "general register files" diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt index d49e22d2a8b5..1baf19eecabf 100644 --- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt @@ -19,11 +19,30 @@ Required Properties: - "samsung,exynos5260-pinctrl": for Exynos5260 compatible pin-controller. - "samsung,exynos5410-pinctrl": for Exynos5410 compatible pin-controller. - "samsung,exynos5420-pinctrl": for Exynos5420 compatible pin-controller. + - "samsung,exynos5433-pinctrl": for Exynos5433 compatible pin-controller. - "samsung,exynos7-pinctrl": for Exynos7 compatible pin-controller. - reg: Base address of the pin controller hardware module and length of the address space it occupies. + - reg: Second base address of the pin controller if the specific registers + of the pin controller are separated into the different base address. + + Eg: GPF[1-5] of Exynos5433 are separated into the two base address. + - First base address is for GPAx and GPF[1-5] external interrupt + registers. + - Second base address is for GPF[1-5] pinctrl registers. + + pinctrl_0: pinctrl@10580000 { + compatible = "samsung,exynos5433-pinctrl"; + reg = <0x10580000 0x1a20>, <0x11090000 0x100>; + + wakeup-interrupt-controller { + compatible = "samsung,exynos7-wakeup-eint"; + interrupts = <0 16 0>; + }; + }; + - Pin banks as child nodes: Pin banks of the controller are represented by child nodes of the controller node. Bank name is taken from name of the node. Each bank node must contain following properties: diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt index f9753c416974..b24583aa34c3 100644 --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt @@ -14,11 +14,6 @@ Required properies: - #size-cells : The value of this property must be 1 - ranges : defines mapping between pin controller node (parent) to gpio-bank node (children). - - interrupt-parent: phandle of the interrupt parent to which the external - GPIO interrupts are forwarded to. - - st,syscfg: Should be phandle/offset pair. The phandle to the syscon node - which includes IRQ mux selection register, and the offset of the IRQ mux - selection register. - pins-are-numbered: Specify the subnodes are using numbered pinmux to specify pins. @@ -37,6 +32,11 @@ Required properties: Optional properties: - reset: : Reference to the reset controller + - interrupt-parent: phandle of the interrupt parent to which the external + GPIO interrupts are forwarded to. + - st,syscfg: Should be phandle/offset pair. The phandle to the syscon node + which includes IRQ mux selection register, and the offset of the IRQ mux + selection register. Example: #include <dt-bindings/pinctrl/stm32f429-pinfunc.h> diff --git a/Documentation/devicetree/bindings/pinctrl/ti,da850-pupd.txt b/Documentation/devicetree/bindings/pinctrl/ti,da850-pupd.txt new file mode 100644 index 000000000000..7f2980567c9f --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/ti,da850-pupd.txt @@ -0,0 +1,55 @@ +* Pin configuration for TI DA850/OMAP-L138/AM18x + +These SoCs have a separate controller for setting bias (internal pullup/down). +Bias can only be selected for groups rather than individual pins. + +Required Properties: + + - compatible: Must be "ti,da850-pupd" + - reg: Base address and length of the memory resource used by the pullup/down + controller hardware module. + +The controller node also acts as a container for pin group configuration nodes. +The names of these groups are ignored. + +Pin Group Node Properties: + +- groups: An array of strings, each string containing the name of a pin group. + Valid names are "cp0".."cp31". + +The pin configuration parameters use the generic pinconf bindings defined in +pinctrl-bindings.txt in this directory. The supported parameters are +bias-disable, bias-pull-up, bias-pull-down. + + +Example +------- + +In common dtsi file: + + pinconf: pin-controller@22c00c { + compatible = "ti,da850-pupd"; + reg = <0x22c00c 0x8>; + }; + +In board-specific file: + + &pinconf { + pinctrl-0 = <&pinconf_bias_groups>; + pinctrl-names = "default"; + + pinconf_bias_groups: bias-groups { + pull-up { + groups = "cp30", "cp31"; + bias-pull-up; + }; + pull-down { + groups = "cp29", "cp28"; + bias-pull-down; + }; + disable { + groups = "cp27", "cp26"; + bias-disable; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/power/domain-idle-state.txt b/Documentation/devicetree/bindings/power/domain-idle-state.txt new file mode 100644 index 000000000000..eefc7ed22ca2 --- /dev/null +++ b/Documentation/devicetree/bindings/power/domain-idle-state.txt @@ -0,0 +1,33 @@ +PM Domain Idle State Node: + +A domain idle state node represents the state parameters that will be used to +select the state when there are no active components in the domain. + +The state node has the following parameters - + +- compatible: + Usage: Required + Value type: <string> + Definition: Must be "domain-idle-state". + +- entry-latency-us + Usage: Required + Value type: <prop-encoded-array> + Definition: u32 value representing worst case latency in + microseconds required to enter the idle state. + The exit-latency-us duration may be guaranteed + only after entry-latency-us has passed. + +- exit-latency-us + Usage: Required + Value type: <prop-encoded-array> + Definition: u32 value representing worst case latency + in microseconds required to exit the idle state. + +- min-residency-us + Usage: Required + Value type: <prop-encoded-array> + Definition: u32 value representing minimum residency duration + in microseconds after which the idle state will yield + power benefits after overcoming the overhead in entering +i the idle state. diff --git a/Documentation/devicetree/bindings/power/power_domain.txt b/Documentation/devicetree/bindings/power/power_domain.txt index 025b5e7df61c..723e1ad937da 100644 --- a/Documentation/devicetree/bindings/power/power_domain.txt +++ b/Documentation/devicetree/bindings/power/power_domain.txt @@ -29,6 +29,15 @@ Optional properties: specified by this binding. More details about power domain specifier are available in the next section. +- domain-idle-states : A phandle of an idle-state that shall be soaked into a + generic domain power state. The idle state definitions are + compatible with domain-idle-state specified in [1]. + The domain-idle-state property reflects the idle state of this PM domain and + not the idle states of the devices or sub-domains in the PM domain. Devices + and sub-domains have their own idle-states independent of the parent + domain's idle states. In the absence of this property, the domain would be + considered as capable of being powered-on or powered-off. + Example: power: power-controller@12340000 { @@ -59,6 +68,38 @@ The nodes above define two power controllers: 'parent' and 'child'. Domains created by the 'child' power controller are subdomains of '0' power domain provided by the 'parent' power controller. +Example 3: + parent: power-controller@12340000 { + compatible = "foo,power-controller"; + reg = <0x12340000 0x1000>; + #power-domain-cells = <0>; + domain-idle-states = <&DOMAIN_RET>, <&DOMAIN_PWR_DN>; + }; + + child: power-controller@12341000 { + compatible = "foo,power-controller"; + reg = <0x12341000 0x1000>; + power-domains = <&parent 0>; + #power-domain-cells = <0>; + domain-idle-states = <&DOMAIN_PWR_DN>; + }; + + DOMAIN_RET: state@0 { + compatible = "domain-idle-state"; + reg = <0x0>; + entry-latency-us = <1000>; + exit-latency-us = <2000>; + min-residency-us = <10000>; + }; + + DOMAIN_PWR_DN: state@1 { + compatible = "domain-idle-state"; + reg = <0x1>; + entry-latency-us = <5000>; + exit-latency-us = <8000>; + min-residency-us = <7000>; + }; + ==PM domain consumers== Required properties: @@ -76,3 +117,5 @@ Example: The node above defines a typical PM domain consumer device, which is located inside a PM domain with index 0 of a power controller represented by a node with the label "power". + +[1]. Documentation/devicetree/bindings/power/domain-idle-state.txt diff --git a/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt b/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt index fb6fb31bc4c4..cf573e85b11d 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt @@ -3,7 +3,7 @@ BCM2835 PWM controller (Raspberry Pi controller) Required properties: - compatible: should be "brcm,bcm2835-pwm" - reg: physical base address and length of the controller's registers -- clock: This clock defines the base clock frequency of the PWM hardware +- clocks: This clock defines the base clock frequency of the PWM hardware system, the period and the duty_cycle of the PWM signal is a multiple of the base period. - #pwm-cells: Should be 2. See pwm.txt in this directory for a description of diff --git a/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt b/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt new file mode 100644 index 000000000000..fa7849d67836 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt @@ -0,0 +1,21 @@ +Hisilicon PWM controller + +Required properties: +-compatible: should contain one SoC specific compatible string + The SoC specific strings supported including: + "hisilicon,hi3516cv300-pwm" + "hisilicon,hi3519v100-pwm" +- reg: physical base address and length of the controller's registers. +- clocks: phandle and clock specifier of the PWM reference clock. +- resets: phandle and reset specifier for the PWM controller reset. +- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of + the cells format. + +Example: + pwm: pwm@12130000 { + compatible = "hisilicon,hi3516cv300-pwm"; + reg = <0x12130000 0x10000>; + clocks = <&crg_ctrl HI3516CV300_PWM_CLK>; + resets = <&crg_ctrl 0x38 0>; + #pwm-cells = <3>; + }; diff --git a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt index 3aeba9f86ed8..bf85aa9ad6a7 100644 --- a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt @@ -59,7 +59,7 @@ Any property defined as part of the core regulator binding can also be used. Continuous Voltage With Enable GPIO Example: pwm_regulator { - compatible = "pwm-regulator; + compatible = "pwm-regulator"; pwms = <&pwm1 0 8448 0>; enable-gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>; regulator-min-microvolt = <1016000>; @@ -76,7 +76,7 @@ Continuous Voltage With Enable GPIO Example: Voltage Table Example: pwm_regulator { - compatible = "pwm-regulator; + compatible = "pwm-regulator"; pwms = <&pwm1 0 8448 0>; regulator-min-microvolt = <1016000>; regulator-max-microvolt = <1114000>; diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt b/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt new file mode 100644 index 000000000000..b85885a298d8 --- /dev/null +++ b/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt @@ -0,0 +1,98 @@ +Qualcomm ADSP Peripheral Image Loader + +This document defines the binding for a component that loads and boots firmware +on the Qualcomm ADSP Hexagon core. + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,msm8974-adsp-pil" + "qcom,msm8996-adsp-pil" + +- interrupts-extended: + Usage: required + Value type: <prop-encoded-array> + Definition: must list the watchdog, fatal IRQs ready, handover and + stop-ack IRQs + +- interrupt-names: + Usage: required + Value type: <stringlist> + Definition: must be "wdog", "fatal", "ready", "handover", "stop-ack" + +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: reference to the xo clock to be held on behalf of the + booting Hexagon core + +- clock-names: + Usage: required + Value type: <stringlist> + Definition: must be "xo" + +- cx-supply: + Usage: required + Value type: <phandle> + Definition: reference to the regulator to be held on behalf of the + booting Hexagon core + +- memory-region: + Usage: required + Value type: <phandle> + Definition: reference to the reserved-memory for the ADSP + +- qcom,smem-states: + Usage: required + Value type: <phandle> + Definition: reference to the smem state for requesting the ADSP to + shut down + +- qcom,smem-state-names: + Usage: required + Value type: <stringlist> + Definition: must be "stop" + + += SUBNODES +The adsp node may have an subnode named "smd-edge" that describes the SMD edge, +channels and devices related to the ADSP. See ../soc/qcom/qcom,smd.txt for +details on how to describe the SMD edge. + + += EXAMPLE +The following example describes the resources needed to boot control the +ADSP, as it is found on MSM8974 boards. + + adsp { + compatible = "qcom,msm8974-adsp-pil"; + + interrupts-extended = <&intc 0 162 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "wdog", + "fatal", + "ready", + "handover", + "stop-ack"; + + clocks = <&rpmcc RPM_CXO_CLK>; + clock-names = "xo"; + + cx-supply = <&pm8841_s2>; + + memory-region = <&adsp_region>; + + qcom,smem-states = <&adsp_smp2p_out 0>; + qcom,smem-state-names = "stop"; + + smd-edge { + interrupts = <0 156 IRQ_TYPE_EDGE_RISING>; + + qcom,ipc = <&apcs 8 8>; + qcom,smd-edge = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.txt b/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.txt index 0d2361ebe3d7..d420f84ddfb0 100644 --- a/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.txt +++ b/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.txt @@ -60,8 +60,8 @@ on the Qualcomm WCNSS core. see ../reserved-memory/reserved-memory.txt = SUBNODES -A single subnode of the WCNSS PIL describes the attached rf module and its -resource dependencies. +A required subnode of the WCNSS PIL is used to describe the attached rf module +and its resource dependencies. It is described by the following properties: - compatible: Usage: required @@ -90,6 +90,11 @@ resource dependencies. Definition: reference to the regulators to be held on behalf of the booting of the WCNSS core + +The wcnss node can also have an subnode named "smd-edge" that describes the SMD +edge, channels and devices related to the WCNSS. +See ../soc/qcom/qcom,smd.txt for details on how to describe the SMD edge. + = EXAMPLE The following example describes the resources needed to boot control the WCNSS, with attached WCN3680, as it is commonly found on MSM8974 boards. @@ -129,4 +134,25 @@ pronto@fb204000 { vddpa-supply = <&pm8941_l19>; vdddig-supply = <&pm8941_s3>; }; + + smd-edge { + interrupts = <0 142 1>; + + qcom,ipc = <&apcs 8 17>; + qcom,smd-edge = <6>; + qcom,remote-pid = <4>; + + label = "pronto"; + + wcnss { + compatible = "qcom,wcnss"; + qcom,smd-channels = "WCNSS_CTRL"; + + qcom,mmio = <&pronto>; + + bt { + compatible = "qcom,wcnss-bt"; + }; + }; + }; }; diff --git a/Documentation/devicetree/bindings/reserved-memory/ramoops.txt b/Documentation/devicetree/bindings/reserved-memory/ramoops.txt index e81f821a2135..0eba562fe5c6 100644 --- a/Documentation/devicetree/bindings/reserved-memory/ramoops.txt +++ b/Documentation/devicetree/bindings/reserved-memory/ramoops.txt @@ -46,3 +46,6 @@ Optional properties: (defaults to buffered mappings) - no-dump-oops: if present, only dump panics (defaults to panics and oops) + +- flags: if present, pass ramoops behavioral flags (defaults to 0, + see include/linux/pstore_ram.h RAMOOPS_FLAG_* for flag values). diff --git a/Documentation/devicetree/bindings/reset/renesas,rst.txt b/Documentation/devicetree/bindings/reset/renesas,rst.txt new file mode 100644 index 000000000000..fe5e0f37b3c9 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/renesas,rst.txt @@ -0,0 +1,37 @@ +DT bindings for the Renesas R-Car and RZ/G Reset Controllers + +The R-Car and RZ/G Reset Controllers provide reset control, and implement the +following functions: + - Latching of the levels on mode pins when PRESET# is negated, + - Mode monitoring register, + - Reset control of peripheral devices (on R-Car Gen1), + - Watchdog timer (on R-Car Gen1), + - Register-based reset control and boot address registers for the various CPU + cores (on R-Car Gen2 and Gen3, and on RZ/G). + + +Required properties: + - compatible: Should be + - "renesas,<soctype>-reset-wdt" for R-Car Gen1, + - "renesas,<soctype>-rst" for R-Car Gen2 and Gen3, and RZ/G + Examples with soctypes are: + - "renesas,r8a7743-rst" (RZ/G1M) + - "renesas,r8a7745-rst" (RZ/G1E) + - "renesas,r8a7778-reset-wdt" (R-Car M1A) + - "renesas,r8a7779-reset-wdt" (R-Car H1) + - "renesas,r8a7790-rst" (R-Car H2) + - "renesas,r8a7791-rst" (R-Car M2-W) + - "renesas,r8a7792-rst" (R-Car V2H + - "renesas,r8a7793-rst" (R-Car M2-N) + - "renesas,r8a7794-rst" (R-Car E2) + - "renesas,r8a7795-rst" (R-Car H3) + - "renesas,r8a7796-rst" (R-Car M3-W) + - reg: Address start and address range for the device. + + +Example: + + rst: reset-controller@e6160000 { + compatible = "renesas,r8a7795-rst"; + reg = <0 0xe6160000 0 0x0200>; + }; diff --git a/Documentation/devicetree/bindings/reset/uniphier-reset.txt b/Documentation/devicetree/bindings/reset/uniphier-reset.txt index e6bbfccd56c3..5020524cddeb 100644 --- a/Documentation/devicetree/bindings/reset/uniphier-reset.txt +++ b/Documentation/devicetree/bindings/reset/uniphier-reset.txt @@ -6,25 +6,25 @@ System reset Required properties: - compatible: should be one of the following: - "socionext,uniphier-sld3-reset" - for PH1-sLD3 SoC. - "socionext,uniphier-ld4-reset" - for PH1-LD4 SoC. - "socionext,uniphier-pro4-reset" - for PH1-Pro4 SoC. - "socionext,uniphier-sld8-reset" - for PH1-sLD8 SoC. - "socionext,uniphier-pro5-reset" - for PH1-Pro5 SoC. - "socionext,uniphier-pxs2-reset" - for ProXstream2/PH1-LD6b SoC. - "socionext,uniphier-ld11-reset" - for PH1-LD11 SoC. - "socionext,uniphier-ld20-reset" - for PH1-LD20 SoC. + "socionext,uniphier-sld3-reset" - for sLD3 SoC. + "socionext,uniphier-ld4-reset" - for LD4 SoC. + "socionext,uniphier-pro4-reset" - for Pro4 SoC. + "socionext,uniphier-sld8-reset" - for sLD8 SoC. + "socionext,uniphier-pro5-reset" - for Pro5 SoC. + "socionext,uniphier-pxs2-reset" - for PXs2/LD6b SoC. + "socionext,uniphier-ld11-reset" - for LD11 SoC. + "socionext,uniphier-ld20-reset" - for LD20 SoC. - #reset-cells: should be 1. Example: sysctrl@61840000 { - compatible = "socionext,uniphier-ld20-sysctrl", + compatible = "socionext,uniphier-ld11-sysctrl", "simple-mfd", "syscon"; reg = <0x61840000 0x4000>; reset { - compatible = "socionext,uniphier-ld20-reset"; + compatible = "socionext,uniphier-ld11-reset"; #reset-cells = <1>; }; @@ -32,30 +32,30 @@ Example: }; -Media I/O (MIO) reset ---------------------- +Media I/O (MIO) reset, SD reset +------------------------------- Required properties: - compatible: should be one of the following: - "socionext,uniphier-sld3-mio-reset" - for PH1-sLD3 SoC. - "socionext,uniphier-ld4-mio-reset" - for PH1-LD4 SoC. - "socionext,uniphier-pro4-mio-reset" - for PH1-Pro4 SoC. - "socionext,uniphier-sld8-mio-reset" - for PH1-sLD8 SoC. - "socionext,uniphier-pro5-mio-reset" - for PH1-Pro5 SoC. - "socionext,uniphier-pxs2-mio-reset" - for ProXstream2/PH1-LD6b SoC. - "socionext,uniphier-ld11-mio-reset" - for PH1-LD11 SoC. - "socionext,uniphier-ld20-mio-reset" - for PH1-LD20 SoC. + "socionext,uniphier-sld3-mio-reset" - for sLD3 SoC. + "socionext,uniphier-ld4-mio-reset" - for LD4 SoC. + "socionext,uniphier-pro4-mio-reset" - for Pro4 SoC. + "socionext,uniphier-sld8-mio-reset" - for sLD8 SoC. + "socionext,uniphier-pro5-sd-reset" - for Pro5 SoC. + "socionext,uniphier-pxs2-sd-reset" - for PXs2/LD6b SoC. + "socionext,uniphier-ld11-mio-reset" - for LD11 SoC. + "socionext,uniphier-ld20-sd-reset" - for LD20 SoC. - #reset-cells: should be 1. Example: mioctrl@59810000 { - compatible = "socionext,uniphier-ld20-mioctrl", + compatible = "socionext,uniphier-ld11-mioctrl", "simple-mfd", "syscon"; reg = <0x59810000 0x800>; reset { - compatible = "socionext,uniphier-ld20-mio-reset"; + compatible = "socionext,uniphier-ld11-mio-reset"; #reset-cells = <1>; }; @@ -68,24 +68,24 @@ Peripheral reset Required properties: - compatible: should be one of the following: - "socionext,uniphier-ld4-peri-reset" - for PH1-LD4 SoC. - "socionext,uniphier-pro4-peri-reset" - for PH1-Pro4 SoC. - "socionext,uniphier-sld8-peri-reset" - for PH1-sLD8 SoC. - "socionext,uniphier-pro5-peri-reset" - for PH1-Pro5 SoC. - "socionext,uniphier-pxs2-peri-reset" - for ProXstream2/PH1-LD6b SoC. - "socionext,uniphier-ld11-peri-reset" - for PH1-LD11 SoC. - "socionext,uniphier-ld20-peri-reset" - for PH1-LD20 SoC. + "socionext,uniphier-ld4-peri-reset" - for LD4 SoC. + "socionext,uniphier-pro4-peri-reset" - for Pro4 SoC. + "socionext,uniphier-sld8-peri-reset" - for sLD8 SoC. + "socionext,uniphier-pro5-peri-reset" - for Pro5 SoC. + "socionext,uniphier-pxs2-peri-reset" - for PXs2/LD6b SoC. + "socionext,uniphier-ld11-peri-reset" - for LD11 SoC. + "socionext,uniphier-ld20-peri-reset" - for LD20 SoC. - #reset-cells: should be 1. Example: perictrl@59820000 { - compatible = "socionext,uniphier-ld20-perictrl", + compatible = "socionext,uniphier-ld11-perictrl", "simple-mfd", "syscon"; reg = <0x59820000 0x200>; reset { - compatible = "socionext,uniphier-ld20-peri-reset"; + compatible = "socionext,uniphier-ld11-peri-reset"; #reset-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/rng/omap_rng.txt b/Documentation/devicetree/bindings/rng/omap_rng.txt index 6a62acd86953..471477299ece 100644 --- a/Documentation/devicetree/bindings/rng/omap_rng.txt +++ b/Documentation/devicetree/bindings/rng/omap_rng.txt @@ -1,4 +1,4 @@ -OMAP SoC HWRNG Module +OMAP SoC and Inside-Secure HWRNG Module Required properties: @@ -6,11 +6,13 @@ Required properties: RNG versions: - "ti,omap2-rng" for OMAP2. - "ti,omap4-rng" for OMAP4, OMAP5 and AM33XX. + - "inside-secure,safexcel-eip76" for SoCs with EIP76 IP block Note that these two versions are incompatible. - ti,hwmods: Name of the hwmod associated with the RNG module - reg : Offset and length of the register set for the module - interrupts : the interrupt number for the RNG module. - Only used for "ti,omap4-rng". + Used for "ti,omap4-rng" and "inside-secure,safexcel-eip76" +- clocks: the trng clock source Example: /* AM335x */ @@ -20,3 +22,11 @@ rng: rng@48310000 { reg = <0x48310000 0x2000>; interrupts = <111>; }; + +/* SafeXcel IP-76 */ +trng: rng@f2760000 { + compatible = "inside-secure,safexcel-eip76"; + reg = <0xf2760000 0x7d>; + interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpm_syscon0 1 25>; +}; diff --git a/Documentation/devicetree/bindings/rtc/maxim,ds3231.txt b/Documentation/devicetree/bindings/rtc/maxim,ds3231.txt index ddef330d2709..1ad4c1c2b3b3 100644 --- a/Documentation/devicetree/bindings/rtc/maxim,ds3231.txt +++ b/Documentation/devicetree/bindings/rtc/maxim,ds3231.txt @@ -1,7 +1,7 @@ * Maxim DS3231 Real Time Clock Required properties: -see: Documentation/devicetree/bindings/i2c/trivial-devices.txt +see: Documentation/devicetree/bindings/i2c/trivial-admin-guide/devices.rst Optional property: - #clock-cells: Should be 1. diff --git a/Documentation/devicetree/bindings/rtc/pcf8563.txt b/Documentation/devicetree/bindings/rtc/pcf8563.txt index 72f6d2c9665e..086c998c5561 100644 --- a/Documentation/devicetree/bindings/rtc/pcf8563.txt +++ b/Documentation/devicetree/bindings/rtc/pcf8563.txt @@ -3,7 +3,7 @@ Philips PCF8563/Epson RTC8564 Real Time Clock Required properties: -see: Documentation/devicetree/bindings/i2c/trivial-devices.txt +see: Documentation/devicetree/bindings/i2c/trivial-admin-guide/devices.rst Optional property: - #clock-cells: Should be 0. diff --git a/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt b/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt index bf2411f366e5..2a42a323fa1a 100644 --- a/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt +++ b/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt @@ -6,6 +6,7 @@ Main node required properties: - compatible : value should be as follows: (a) "hisilicon,hip05-sas-v1" for v1 hw in hip05 chipset (b) "hisilicon,hip06-sas-v2" for v2 hw in hip06 chipset + (c) "hisilicon,hip07-sas-v2" for v2 hw in hip07 chipset - sas-addr : array of 8 bytes for host SAS address - reg : Address and length of the SAS register - hisilicon,sas-syscon: phandle of syscon used for sas control diff --git a/Documentation/devicetree/bindings/security/tpm/ibmvtpm.txt b/Documentation/devicetree/bindings/security/tpm/ibmvtpm.txt new file mode 100644 index 000000000000..d89f99971368 --- /dev/null +++ b/Documentation/devicetree/bindings/security/tpm/ibmvtpm.txt @@ -0,0 +1,41 @@ +* Device Tree Bindings for IBM Virtual Trusted Platform Module(vtpm) + +Required properties: + +- compatible : property name that conveys the platform architecture + identifiers, as 'IBM,vtpm' +- device_type : specifies type of virtual device +- interrupts : property specifying the interrupt source number and + sense code associated with this virtual I/O Adapters +- ibm,my-drc-index : integer index for the connector between the device + and its parent - present only if Dynamic + Reconfiguration(DR) Connector is enabled +- ibm,#dma-address-cells: specifies the number of cells that are used to + encode the physical address field of dma-window + properties +- ibm,#dma-size-cells : specifies the number of cells that are used to + encode the size field of dma-window properties +- ibm,my-dma-window : specifies DMA window associated with this virtual + IOA +- ibm,loc-code : specifies the unique and persistent location code + associated with this virtual I/O Adapters +- linux,sml-base : 64-bit base address of the reserved memory allocated + for the firmware event log +- linux,sml-size : size of the memory allocated for the firmware event log + +Example (IBM Virtual Trusted Platform Module) +--------------------------------------------- + + vtpm@30000003 { + ibm,#dma-size-cells = <0x2>; + compatible = "IBM,vtpm"; + device_type = "IBM,vtpm"; + ibm,my-drc-index = <0x30000003>; + ibm,#dma-address-cells = <0x2>; + linux,sml-base = <0xc60e 0x0>; + interrupts = <0xa0003 0x0>; + ibm,my-dma-window = <0x10000003 0x0 0x0 0x0 0x10000000>; + ibm,loc-code = "U8286.41A.10082DV-V3-C3"; + reg = <0x30000003>; + linux,sml-size = <0xbce10200>; + }; diff --git a/Documentation/devicetree/bindings/security/tpm/tpm-i2c.txt b/Documentation/devicetree/bindings/security/tpm/tpm-i2c.txt new file mode 100644 index 000000000000..8cb638b7e89c --- /dev/null +++ b/Documentation/devicetree/bindings/security/tpm/tpm-i2c.txt @@ -0,0 +1,21 @@ +* Device Tree Bindings for I2C based Trusted Platform Module(TPM) + +Required properties: + +- compatible : 'manufacturer,model', eg. nuvoton,npct650 +- label : human readable string describing the device, eg. "tpm" +- linux,sml-base : 64-bit base address of the reserved memory allocated for + the firmware event log +- linux,sml-size : size of the memory allocated for the firmware event log + +Example (for OpenPower Systems with Nuvoton TPM 2.0 on I2C) +---------------------------------------------------------- + +tpm@57 { + reg = <0x57>; + label = "tpm"; + compatible = "nuvoton,npct650", "nuvoton,npct601"; + linux,sml-base = <0x7f 0xfd450000>; + linux,sml-size = <0x10000>; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/security/tpm/tpm_tis_mmio.txt b/Documentation/devicetree/bindings/security/tpm/tpm_tis_mmio.txt new file mode 100644 index 000000000000..41d740545189 --- /dev/null +++ b/Documentation/devicetree/bindings/security/tpm/tpm_tis_mmio.txt @@ -0,0 +1,25 @@ +Trusted Computing Group MMIO Trusted Platform Module + +The TCG defines multi vendor standard for accessing a TPM chip, this +is the standard protocol defined to access the TPM via MMIO. Typically +this interface will be implemented over Intel's LPC bus. + +Refer to the 'TCG PC Client Specific TPM Interface Specification (TIS)' TCG +publication for the specification. + +Required properties: + +- compatible: should contain a string below for the chip, followed by + "tcg,tpm-tis-mmio". Valid chip strings are: + * "atmel,at97sc3204" +- reg: The location of the MMIO registers, should be at least 0x5000 bytes +- interrupt-parent/interrupts: An optional interrupt indicating command completion. + +Example: + + tpm_tis@90000 { + compatible = "atmel,at97sc3204", "tcg,tpm-tis-mmio"; + reg = <0x90000 0x5000>; + interrupt-parent = <&EIC0>; + interrupts = <1 2>; + }; diff --git a/Documentation/devicetree/bindings/serial/cdns,uart.txt b/Documentation/devicetree/bindings/serial/cdns,uart.txt index a3eb154c32ca..227bb770b027 100644 --- a/Documentation/devicetree/bindings/serial/cdns,uart.txt +++ b/Documentation/devicetree/bindings/serial/cdns,uart.txt @@ -1,7 +1,9 @@ Binding for Cadence UART Controller Required properties: -- compatible : should be "cdns,uart-r1p8", or "xlnx,xuartps" +- compatible : + Use "xlnx,xuartps","cdns,uart-r1p8" for Zynq-7xxx SoC. + Use "xlnx,zynqmp-uart","cdns,uart-r1p12" for Zynq Ultrascale+ MPSoC. - reg: Should contain UART controller registers location and length. - interrupts: Should contain UART controller interrupts. - clocks: Must contain phandles to the UART clocks diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index 1e4000d83aee..8d27d1a603e7 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -9,6 +9,14 @@ Required properties: - "renesas,scifb-r8a73a4" for R8A73A4 (R-Mobile APE6) SCIFB compatible UART. - "renesas,scifa-r8a7740" for R8A7740 (R-Mobile A1) SCIFA compatible UART. - "renesas,scifb-r8a7740" for R8A7740 (R-Mobile A1) SCIFB compatible UART. + - "renesas,scif-r8a7743" for R8A7743 (RZ/G1M) SCIF compatible UART. + - "renesas,scifa-r8a7743" for R8A7743 (RZ/G1M) SCIFA compatible UART. + - "renesas,scifb-r8a7743" for R8A7743 (RZ/G1M) SCIFB compatible UART. + - "renesas,hscif-r8a7743" for R8A7743 (RZ/G1M) HSCIF compatible UART. + - "renesas,scif-r8a7745" for R8A7745 (RZ/G1E) SCIF compatible UART. + - "renesas,scifa-r8a7745" for R8A7745 (RZ/G1E) SCIFA compatible UART. + - "renesas,scifb-r8a7745" for R8A7745 (RZ/G1E) SCIFB compatible UART. + - "renesas,hscif-r8a7745" for R8A7745 (RZ/G1E) HSCIF compatible UART. - "renesas,scif-r8a7778" for R8A7778 (R-Car M1) SCIF compatible UART. - "renesas,scif-r8a7779" for R8A7779 (R-Car H1) SCIF compatible UART. - "renesas,scif-r8a7790" for R8A7790 (R-Car H2) SCIF compatible UART. diff --git a/Documentation/devicetree/bindings/powerpc/fsl/guts.txt b/Documentation/devicetree/bindings/soc/fsl/guts.txt index b71b2039e112..07adca914d3d 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/guts.txt +++ b/Documentation/devicetree/bindings/soc/fsl/guts.txt @@ -25,6 +25,9 @@ Recommended properties: - fsl,liodn-bits : Indicates the number of defined bits in the LIODN registers, for those SOCs that have a PAMU device. + - little-endian : Indicates that the global utilities block is little + endian. The default is big endian. + Examples: global-utilities@e0000 { /* global utilities block */ compatible = "fsl,mpc8548-guts"; diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt index 97d9b3e1bf39..ea1dc75ec9ea 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt @@ -43,6 +43,13 @@ The edge is described by the following properties: Definition: the identifier for the remote processor as known by the rest of the system. +- label: + Usage: optional + Value type: <string> + Definition: name of the edge, used for debugging and identification + purposes. The node name will be used if this is not + present. + = SMD DEVICES In turn, subnodes of the "edges" represent devices tied to SMD channels on that diff --git a/Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt b/Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt new file mode 100644 index 000000000000..5b9b38f578bb --- /dev/null +++ b/Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt @@ -0,0 +1,88 @@ +Devicetree bindings for the Axentia TSE-850 audio complex + +Required properties: + - compatible: "axentia,tse850-pcm5142" + - axentia,ssc-controller: The phandle of the atmel SSC controller used as + cpu dai. + - axentia,audio-codec: The phandle of the PCM5142 codec. + - axentia,add-gpios: gpio specifier that controls the mixer. + - axentia,loop1-gpios: gpio specifier that controls loop relays on channel 1. + - axentia,loop2-gpios: gpio specifier that controls loop relays on channel 2. + - axentia,ana-supply: Regulator that supplies the output amplifier. Must + support voltages in the 2V - 20V range, in 1V steps. + +The schematics explaining the gpios are as follows: + + loop1 relays + IN1 +---o +------------+ o---+ OUT1 + \ / + + + + | / | + +--o +--. | + | add | | + | V | + | .---. | + DAC +----------->|Sum|---+ + | '---' | + | | + + + + + IN2 +---o--+------------+--o---+ OUT2 + loop2 relays + +The 'loop1' gpio pin controlls two relays, which are either in loop position, +meaning that input and output are directly connected, or they are in mixer +position, meaning that the signal is passed through the 'Sum' mixer. Similarly +for 'loop2'. + +In the above, the 'loop1' relays are inactive, thus feeding IN1 to the mixer +(if 'add' is active) and feeding the mixer output to OUT1. The 'loop2' relays +are active, short-cutting the TSE-850 from channel 2. IN1, IN2, OUT1 and OUT2 +are TSE-850 connectors and DAC is the PCB name of the (filtered) output from +the PCM5142 codec. + +Example: + + &i2c { + codec: pcm5142@4c { + compatible = "ti,pcm5142"; + + reg = <0x4c>; + + AVDD-supply = <®_3v3>; + DVDD-supply = <®_3v3>; + CPVDD-supply = <®_3v3>; + + clocks = <&sck>; + + pll-in = <3>; + pll-out = <6>; + }; + }; + + ana: ana-reg { + compatible = "pwm-regulator"; + + regulator-name = "ANA"; + + pwms = <&pwm0 2 1000 PWM_POLARITY_INVERTED>; + pwm-dutycycle-unit = <1000>; + pwm-dutycycle-range = <100 1000>; + + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <20000000>; + regulator-ramp-delay = <1000>; + }; + + sound { + compatible = "axentia,tse850-pcm5142"; + + axentia,ssc-controller = <&ssc0>; + axentia,audio-codec = <&codec>; + + axentia,add-gpios = <&pioA 8 GPIO_ACTIVE_LOW>; + axentia,loop1-gpios = <&pioA 10 GPIO_ACTIVE_LOW>; + axentia,loop2-gpios = <&pioA 11 GPIO_ACTIVE_LOW>; + + axentia,ana-supply = <&ana>; + }; diff --git a/Documentation/devicetree/bindings/sound/cs35l34.txt b/Documentation/devicetree/bindings/sound/cs35l34.txt new file mode 100644 index 000000000000..b218ead2e68e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs35l34.txt @@ -0,0 +1,64 @@ +CS35L34 Speaker Amplifier + +Required properties: + + - compatible : "cirrus,cs35l34" + + - reg : the I2C address of the device for I2C. + + - VA-supply, VP-supply : power supplies for the device, + as covered in + Documentation/devicetree/bindings/regulator/regulator.txt. + + - cirrus,boost-vtge-millivolt : Boost Voltage Value. Configures the boost + converter's output voltage in mV. The range is from VP to 8V with + increments of 100mV. + + - cirrus,boost-nanohenry: Inductor value for boost converter. The value is + in nH and they can be values of 1000nH, 1100nH, 1200nH, 1500nH, and 2200nH. + +Optional properties: + + - reset-gpios: GPIO used to reset the amplifier. + + - interrupt-parent : Specifies the phandle of the interrupt controller to + which the IRQs from CS35L34 are delivered to. + - interrupts : IRQ line info CS35L34. + (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + for further information relating to interrupt properties) + + - cirrus,boost-peak-milliamp : Boost converter peak current limit in mA. The + range starts at 1200mA and goes to a maximum of 3840mA with increments of + 80mA. The default value is 2480mA. + + - cirrus,i2s-sdinloc : ADSP SDIN I2S channel location. Indicates whether the + received mono data is in the left or right portion of the I2S frame + according to the AD0 pin or directly via this configuration. + 0x0 (Default) = Selected by AD0 input (if AD0 = LOW, use left channel), + 0x2 = Left, + 0x1 = Selected by the inversion of the AD0 input (if AD0 = LOW, use right + channel), + 0x3 = Right. + + - cirrus,gain-zc-disable: Boolean property. If set, the gain change will take + effect without waiting for a zero cross. + + - cirrus,tdm-rising-edge: Boolean property. If set, data is on the rising edge of + SCLK. Otherwise, data is on the falling edge of SCLK. + + +Example: + +cs35l34: cs35l34@40 { + compatible = "cirrus,cs35l34"; + reg = <0x40>; + + interrupt-parent = <&gpio8>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + + reset-gpios = <&gpio 10 0>; + + cirrus,boost-vtge-milltvolt = <8000>; /* 8V */ + cirrus,boost-ind-nanohenry = <1000>; /* 1uH */ + cirrus,boost-peak-milliamp = <3000>; /* 3A */ +}; diff --git a/Documentation/devicetree/bindings/sound/cs42l42.txt b/Documentation/devicetree/bindings/sound/cs42l42.txt new file mode 100644 index 000000000000..9a2c5e2423d5 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs42l42.txt @@ -0,0 +1,110 @@ +CS42L42 audio CODEC + +Required properties: + + - compatible : "cirrus,cs42l42" + + - reg : the I2C address of the device for I2C. + + - VP-supply, VCP-supply, VD_FILT-supply, VL-supply, VA-supply : + power supplies for the device, as covered in + Documentation/devicetree/bindings/regulator/regulator.txt. + +Optional properties: + + - reset-gpios : a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the codec starts. + + - interrupt-parent : Specifies the phandle of the interrupt controller to + which the IRQs from CS42L42 are delivered to. + + - interrupts : IRQ line info CS42L42. + (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + for further information relating to interrupt properties) + + - cirrus,ts-inv : Boolean property. For jacks that invert the tip sense + polarity. Normal jacks will short tip sense pin to HS1 when headphones are + plugged in and leave tip sense floating when not plugged in. Inverting jacks + short tip sense when unplugged and float when plugged in. + + 0 = (Default) Non-inverted + 1 = Inverted + + - cirrus,ts-dbnc-rise : Debounce the rising edge of TIP_SENSE_PLUG. With no + debounce, the tip sense pin might be noisy on a plug event. + + 0 - 0ms, + 1 - 125ms, + 2 - 250ms, + 3 - 500ms, + 4 - 750ms, + 5 - (Default) 1s, + 6 - 1.25s, + 7 - 1.5s, + + - cirrus,ts-dbnc-fall : Debounce the falling edge of TIP_SENSE_UNPLUG. + With no debounce, the tip sense pin might be noisy on an unplug event. + + 0 - 0ms, + 1 - 125ms, + 2 - 250ms, + 3 - 500ms, + 4 - 750ms, + 5 - (Default) 1s, + 6 - 1.25s, + 7 - 1.5s, + + - cirrus,btn-det-init-dbnce : This sets how long the driver sleeps after + enabling button detection interrupts. After auto-detection and before + servicing button interrupts, the HS bias needs time to settle. If you + don't wait, there is possibility for erroneous button interrupt. + + 0ms - 200ms, + Default = 100ms + + - cirrus,btn-det-event-dbnce : This sets how long the driver delays after + receiving a button press interrupt. With level detect interrupts, you want + to wait a small amount of time to make sure the button press is making a + clean connection with the bias resistors. + + 0ms - 20ms, + Default = 10ms + + - cirrus,bias-lvls : For a level-detect headset button scheme, each button + will bias the mic pin to a certain voltage. To determine which button was + pressed, the driver will compare this biased voltage to sequential, + decreasing voltages and will stop when a comparator is tripped, + indicating a comparator voltage < bias voltage. This value represents a + percentage of the internally generated HS bias voltage. For different + hardware setups, a designer might want to tweak this. This is an array of + descending values for the comparator voltage. + + Array of 4 values + Each 0-63 + < x1 x2 x3 x4 > + Default = < 15 8 4 1> + + +Example: + +cs42l42: cs42l42@48 { + compatible = "cirrus,cs42l42"; + reg = <0x48>; + VA-supply = <&dummy_vreg>; + VP-supply = <&dummy_vreg>; + VCP-supply = <&dummy_vreg>; + VD_FILT-supply = <&dummy_vreg>; + VL-supply = <&dummy_vreg>; + + reset-gpios = <&axi_gpio_0 1 0>; + interrupt-parent = <&gpio0>; + interrupts = <55 8> + + cirrus,ts-inv = <0x00>; + cirrus,ts-dbnc-rise = <0x05>; + cirrus,ts-dbnc-fall = <0x00>; + cirrus,btn-det-init-dbnce = <100>; + cirrus,btn-det-event-dbnce = <10>; + cirrus,bias-lvls = <0x0F 0x08 0x04 0x01>; + cirrus,hs-bias-ramp-rate = <0x02>; +};
\ No newline at end of file diff --git a/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt b/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt index 55b53e1fd72c..e0b6165c9cfc 100644 --- a/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt +++ b/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt @@ -43,7 +43,7 @@ mcbsp0: mcbsp@1d10000 { <0x00310000 0x1000>; reg-names = "mpu", "dat"; interrupts = <97 98>; - interrupts-names = "rx", "tx"; + interrupt-names = "rx", "tx"; dmas = <&edma0 3 1 &edma0 2 1>; dma-names = "tx", "rx"; diff --git a/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt b/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt index fd40c852d7c7..462b04e8209f 100644 --- a/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt +++ b/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt @@ -12,7 +12,7 @@ Required properties: Optional properties: - ti,dmic: phandle for the OMAP dmic node if the machine have it connected -- ti,jack_detection: Need to be present if the board capable to detect jack +- ti,jack-detection: Need to be present if the board capable to detect jack insertion, removal. Available audio endpoints for the audio-routing table: diff --git a/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt b/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt index d9d8635ff94c..6a4aadc4ce06 100644 --- a/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt +++ b/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt @@ -44,8 +44,7 @@ Required dai-link subnodes: Required CPU/CODEC subnodes properties: -link-name : Name of the dai link. --sound-dai : phandle and port of CPU/CODEC --capture-dai : phandle and port of CPU/CODEC +-sound-dai : phandle/s and port of CPU/CODEC Example: @@ -73,7 +72,7 @@ sound: sound { sound-dai = <&lpass MI2S_PRIMARY>; }; codec { - sound-dai = <&wcd_codec 0>; + sound-dai = <&lpass_codec 0>, <&wcd_codec 0>; }; }; diff --git a/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt new file mode 100644 index 000000000000..ccb401cfef9d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt @@ -0,0 +1,85 @@ +msm8916 analog audio CODEC + +Bindings for codec Analog IP which is integrated in pmic pm8916, + +## Bindings for codec core on pmic: + +Required properties + - compatible = "qcom,pm8916-wcd-analog-codec"; + - reg: represents the slave base address provided to the peripheral. + - interrupt-parent : The parent interrupt controller. + - interrupts: List of interrupts in given SPMI peripheral. + - interrupt-names: Names specified to above list of interrupts in same + order. List of supported interrupt names are: + "cdc_spk_cnp_int" - Speaker click and pop interrupt. + "cdc_spk_clip_int" - Speaker clip interrupt. + "cdc_spk_ocp_int" - Speaker over current protect interrupt. + "mbhc_ins_rem_det1" - jack insert removal detect interrupt 1. + "mbhc_but_rel_det" - button release interrupt. + "mbhc_but_press_det" - button press event + "mbhc_ins_rem_det" - jack insert removal detect interrupt. + "mbhc_switch_int" - multi button headset interrupt. + "cdc_ear_ocp_int" - Earphone over current protect interrupt. + "cdc_hphr_ocp_int" - Headphone R over current protect interrupt. + "cdc_hphl_ocp_det" - Headphone L over current protect interrupt. + "cdc_ear_cnp_int" - earphone cnp interrupt. + "cdc_hphr_cnp_int" - hphr click and pop interrupt. + "cdc_hphl_cnp_int" - hphl click and pop interrupt. + + - clocks: Handle to mclk. + - clock-names: should be "mclk" + - vdd-cdc-io-supply: phandle to VDD_CDC_IO regulator DT node. + - vdd-cdc-tx-rx-cx-supply: phandle to VDD_CDC_TX/RX/CX regulator DT node. + - vdd-micbias-supply: phandle of VDD_MICBIAS supply's regulator DT node. + +Optional Properties: +- qcom,micbias1-ext-cap: boolean, present if micbias1 has external capacitor + connected. +- qcom,micbias2-ext-cap: boolean, present if micbias2 has external capacitor + connected. + +Example: + +spmi_bus { + ... + audio-codec@f000{ + compatible = "qcom,pm8916-wcd-analog-codec"; + reg = <0xf000 0x200>; + reg-names = "pmic-codec-core"; + clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>; + clock-names = "mclk"; + interrupt-parent = <&spmi_bus>; + interrupts = <0x1 0xf0 0x0 IRQ_TYPE_NONE>, + <0x1 0xf0 0x1 IRQ_TYPE_NONE>, + <0x1 0xf0 0x2 IRQ_TYPE_NONE>, + <0x1 0xf0 0x3 IRQ_TYPE_NONE>, + <0x1 0xf0 0x4 IRQ_TYPE_NONE>, + <0x1 0xf0 0x5 IRQ_TYPE_NONE>, + <0x1 0xf0 0x6 IRQ_TYPE_NONE>, + <0x1 0xf0 0x7 IRQ_TYPE_NONE>, + <0x1 0xf1 0x0 IRQ_TYPE_NONE>, + <0x1 0xf1 0x1 IRQ_TYPE_NONE>, + <0x1 0xf1 0x2 IRQ_TYPE_NONE>, + <0x1 0xf1 0x3 IRQ_TYPE_NONE>, + <0x1 0xf1 0x4 IRQ_TYPE_NONE>, + <0x1 0xf1 0x5 IRQ_TYPE_NONE>; + interrupt-names = "cdc_spk_cnp_int", + "cdc_spk_clip_int", + "cdc_spk_ocp_int", + "mbhc_ins_rem_det1", + "mbhc_but_rel_det", + "mbhc_but_press_det", + "mbhc_ins_rem_det", + "mbhc_switch_int", + "cdc_ear_ocp_int", + "cdc_hphr_ocp_int", + "cdc_hphl_ocp_det", + "cdc_ear_cnp_int", + "cdc_hphr_cnp_int", + "cdc_hphl_cnp_int"; + VDD-CDC-IO-supply = <&pm8916_l5>; + VDD-CDC-TX-RX-CX-supply = <&pm8916_l5>; + VDD-MICBIAS-supply = <&pm8916_l13>; + #sound-dai-cells = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-digital.txt b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-digital.txt new file mode 100644 index 000000000000..1c8e4cb25176 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-digital.txt @@ -0,0 +1,20 @@ +msm8916 digital audio CODEC + +## Bindings for codec core in lpass: + +Required properties + - compatible = "qcom,msm8916-wcd-digital-codec"; + - reg: address space for lpass codec. + - clocks: Handle to mclk and ahbclk + - clock-names: should be "mclk", "ahbix-clk". + +Example: + +audio-codec@771c000{ + compatible = "qcom,msm8916-wcd-digital-codec"; + reg = <0x0771c000 0x400>; + clocks = <&gcc GCC_ULTAUDIO_AHBFABRIC_IXFABRIC_CLK>, + <&gcc GCC_CODEC_DIGCODEC_CLK>; + clock-names = "ahbix-clk", "mclk"; + #sound-dai-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/sound/rt5514.txt b/Documentation/devicetree/bindings/sound/rt5514.txt index 9cabfc18cb57..929ca6756b02 100644 --- a/Documentation/devicetree/bindings/sound/rt5514.txt +++ b/Documentation/devicetree/bindings/sound/rt5514.txt @@ -13,6 +13,9 @@ Optional properties: - clocks: The phandle of the master clock to the CODEC - clock-names: Should be "mclk" +- realtek,dmic-init-delay-ms + Set the DMIC initial delay (ms) to wait it ready. + Pins on the device (for linking into audio routes) for RT5514: * DMIC1L diff --git a/Documentation/devicetree/bindings/sound/rt5663.txt b/Documentation/devicetree/bindings/sound/rt5663.txt index 7d3c974c6e2e..70eaeaed2b18 100644 --- a/Documentation/devicetree/bindings/sound/rt5663.txt +++ b/Documentation/devicetree/bindings/sound/rt5663.txt @@ -1,10 +1,10 @@ -RT5663/RT5668 audio CODEC +RT5663 audio CODEC This device supports I2C only. Required properties: -- compatible : One of "realtek,rt5663" or "realtek,rt5668". +- compatible : "realtek,rt5663". - reg : The I2C address of the device. @@ -12,7 +12,7 @@ Required properties: Optional properties: -Pins on the device (for linking into audio routes) for RT5663/RT5668: +Pins on the device (for linking into audio routes) for RT5663: * IN1P * IN1N diff --git a/Documentation/devicetree/bindings/sound/rt5665.txt b/Documentation/devicetree/bindings/sound/rt5665.txt new file mode 100755 index 000000000000..419c89219681 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5665.txt @@ -0,0 +1,68 @@ +RT5665/RT5666/RT5668 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : One of "realtek,rt5665", "realtek,rt5666" or "realtek,rt5668". + +- reg : The I2C address of the device. + +- interrupts : The CODEC's interrupt output. + +Optional properties: + +- realtek,in1-differential +- realtek,in2-differential +- realtek,in3-differential +- realtek,in4-differential + Boolean. Indicate MIC1/2/3/4 input are differential, rather than single-ended. + +- realtek,dmic1-data-pin + 0: dmic1 is not used + 1: using GPIO4 pin as dmic1 data pin + 2: using IN2N pin as dmic2 data pin + +- realtek,dmic2-data-pin + 0: dmic2 is not used + 1: using GPIO5 pin as dmic2 data pin + 2: using IN2P pin as dmic2 data pin + +- realtek,jd-src + 0: No JD is used + 1: using JD1 as JD source + +- realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin. + +Pins on the device (for linking into audio routes) for RT5659/RT5658: + + * DMIC L1 + * DMIC R1 + * DMIC L2 + * DMIC R2 + * IN1P + * IN1N + * IN2P + * IN2N + * IN3P + * IN3N + * IN4P + * IN4N + * HPOL + * HPOR + * LOUTL + * LOUTR + * MONOOUT + * PDML + * PDMR + +Example: + +rt5659 { + compatible = "realtek,rt5665"; + reg = <0x1b>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(W, 3) GPIO_ACTIVE_HIGH>; + realtek,ldo1-en-gpios = + <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/sound/samsung,tm2-audio.txt b/Documentation/devicetree/bindings/sound/samsung,tm2-audio.txt new file mode 100644 index 000000000000..94442e5673b3 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/samsung,tm2-audio.txt @@ -0,0 +1,38 @@ +Samsung Exynos5433 TM2(E) audio complex with WM5110 codec + +Required properties: + + - compatible : "samsung,tm2-audio" + - model : the user-visible name of this sound complex + - audio-codec : the phandle of the wm5110 audio codec node, + as described in ../mfd/arizona.txt + - i2s-controller : the phandle of the I2S controller + - audio-amplifier : the phandle of the MAX98504 amplifier + - samsung,audio-routing : a list of the connections between audio components; + each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source; valid names for sources and sinks are the + WM5110's and MAX98504's pins and the jacks on the + board: HP, SPK, Main Mic, Sub Mic, Third Mic, + Headset Mic + - mic-bias-gpios : GPIO pin that enables the Main Mic bias regulator + + +Example: + +sound { + compatible = "samsung,tm2-audio"; + audio-codec = <&wm5110>; + i2s-controller = <&i2s0>; + audio-amplifier = <&max98504>; + mic-bias-gpios = <&gpr3 2 0>; + model = "wm5110"; + samsung,audio-routing = + "HP", "HPOUT1L", + "HP", "HPOUT1R", + "SPK", "SPKOUT", + "SPKOUT", "HPOUT2L", + "SPKOUT", "HPOUT2R", + "Main Mic", "MICBIAS2", + "IN1R", "Main Mic"; +}; diff --git a/Documentation/devicetree/bindings/sound/sun4i-codec.txt b/Documentation/devicetree/bindings/sound/sun4i-codec.txt index 0dce690f78f5..3033bd8aab0f 100644 --- a/Documentation/devicetree/bindings/sound/sun4i-codec.txt +++ b/Documentation/devicetree/bindings/sound/sun4i-codec.txt @@ -1,8 +1,12 @@ * Allwinner A10 Codec Required properties: -- compatible: must be either "allwinner,sun4i-a10-codec" or - "allwinner,sun7i-a20-codec" +- compatible: must be one of the following compatibles: + - "allwinner,sun4i-a10-codec" + - "allwinner,sun6i-a31-codec" + - "allwinner,sun7i-a20-codec" + - "allwinner,sun8i-a23-codec" + - "allwinner,sun8i-h3-codec" - reg: must contain the registers location and length - interrupts: must contain the codec interrupt - dmas: DMA channels for tx and rx dma. See the DMA client binding, @@ -17,6 +21,43 @@ Required properties: Optional properties: - allwinner,pa-gpios: gpio to enable external amplifier +Required properties for the following compatibles: + - "allwinner,sun6i-a31-codec" + - "allwinner,sun8i-a23-codec" + - "allwinner,sun8i-h3-codec" +- resets: phandle to the reset control for this device +- allwinner,audio-routing: A list of the connections between audio components. + Each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source. Valid names include: + + Audio pins on the SoC: + "HP" + "HPCOM" + "LINEIN" + "LINEOUT" (not on sun8i-a23) + "MIC1" + "MIC2" + "MIC3" (sun6i-a31 only) + + Microphone biases from the SoC: + "HBIAS" + "MBIAS" + + Board connectors: + "Headphone" + "Headset Mic" + "Line In" + "Line Out" + "Mic" + "Speaker" + +Required properties for the following compatibles: + - "allwinner,sun8i-a23-codec" + - "allwinner,sun8i-h3-codec" +- allwinner,codec-analog-controls: A phandle to the codec analog controls + block in the PRCM. + Example: codec: codec@01c22c00 { #sound-dai-cells = <0>; @@ -28,3 +69,23 @@ codec: codec@01c22c00 { dmas = <&dma 0 19>, <&dma 0 19>; dma-names = "rx", "tx"; }; + +codec: codec@01c22c00 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun6i-a31-codec"; + reg = <0x01c22c00 0x98>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_APB1_CODEC>, <&ccu CLK_CODEC>; + clock-names = "apb", "codec"; + resets = <&ccu RST_APB1_CODEC>; + dmas = <&dma 15>, <&dma 15>; + dma-names = "rx", "tx"; + allwinner,audio-routing = + "Headphone", "HP", + "Speaker", "LINEOUT", + "LINEIN", "Line In", + "MIC1", "MBIAS", + "MIC1", "Mic", + "MIC2", "HBIAS", + "MIC2", "Headset Mic"; +}; diff --git a/Documentation/devicetree/bindings/sound/sun8i-codec-analog.txt b/Documentation/devicetree/bindings/sound/sun8i-codec-analog.txt new file mode 100644 index 000000000000..779b735781ba --- /dev/null +++ b/Documentation/devicetree/bindings/sound/sun8i-codec-analog.txt @@ -0,0 +1,16 @@ +* Allwinner Codec Analog Controls + +Required properties: +- compatible: must be one of the following compatibles: + - "allwinner,sun8i-a23-codec-analog" + - "allwinner,sun8i-h3-codec-analog" + +Required properties if not a sub-node of the PRCM node: +- reg: must contain the registers location and length + +Example: +prcm: prcm@01f01400 { + codec_analog: codec-analog { + compatible = "allwinner,sun8i-a23-codec-analog"; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt b/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt index 9340d2ddcc54..6fbba562eaa7 100644 --- a/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt +++ b/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt @@ -12,6 +12,7 @@ Required properties: "ti,tlv320aic3120" - TLV320AIC3120 (mono speaker amp, MiniDSP) "ti,tlv320aic3111" - TLV320AIC3111 (stereo speaker amp, MiniDSP) "ti,tlv320dac3100" - TLV320DAC3100 (no ADC, mono speaker amp, no MiniDSP) + "ti,tlv320dac3101" - TLV320DAC3101 (no ADC, stereo speaker amp, no MiniDSP) - reg - <int> - I2C slave address - HPVDD-supply, SPRVDD-supply, SPLVDD-supply, AVDD-supply, IOVDD-supply, diff --git a/Documentation/devicetree/bindings/sound/wm8580.txt b/Documentation/devicetree/bindings/sound/wm8580.txt index 7d9821f348da..78fce9b14954 100644 --- a/Documentation/devicetree/bindings/sound/wm8580.txt +++ b/Documentation/devicetree/bindings/sound/wm8580.txt @@ -1,10 +1,10 @@ -WM8580 audio CODEC +WM8580 and WM8581 audio CODEC This device supports I2C only. Required properties: - - compatible : "wlf,wm8580" + - compatible : "wlf,wm8580", "wlf,wm8581" - reg : the I2C address of the device. diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index aa005c1d10d9..da6614c63796 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -10,6 +10,7 @@ Required properties: "renesas,msiof-r8a7792" (R-Car V2H) "renesas,msiof-r8a7793" (R-Car M2-N) "renesas,msiof-r8a7794" (R-Car E2) + "renesas,msiof-r8a7796" (R-Car M3-W) "renesas,msiof-sh73a0" (SH-Mobile AG5) - reg : A list of offsets and lengths of the register sets for the device. diff --git a/Documentation/devicetree/bindings/spi/spi-armada-3700.txt b/Documentation/devicetree/bindings/spi/spi-armada-3700.txt new file mode 100644 index 000000000000..1564aa8c02cd --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-armada-3700.txt @@ -0,0 +1,25 @@ +* Marvell Armada 3700 SPI Controller + +Required Properties: + +- compatible: should be "marvell,armada-3700-spi" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: The interrupt number. The interrupt specifier format depends on + the interrupt controller and of its driver. +- clocks: Must contain the clock source, usually from the North Bridge clocks. +- num-cs: The number of chip selects that is supported by this SPI Controller +- #address-cells: should be 1. +- #size-cells: should be 0. + +Example: + + spi0: spi@10600 { + compatible = "marvell,armada-3700-spi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10600 0x5d>; + clocks = <&nb_perih_clk 7>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; + num-cs = <4>; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt new file mode 100644 index 000000000000..225ace1d0c65 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt @@ -0,0 +1,19 @@ +* Freescale Low Power SPI (LPSPI) for i.MX + +Required properties: +- compatible : + - "fsl,imx7ulp-spi" for LPSPI compatible with the one integrated on i.MX7ULP soc +- reg : address and length of the lpspi master registers +- interrupt-parent : core interrupt controller +- interrupts : lpspi interrupt +- clocks : lpspi clock specifier + +Examples: + +lpspi2: lpspi@40290000 { + compatible = "fsl,imx7ulp-spi"; + reg = <0x40290000 0x10000>; + interrupt-parent = <&intc>; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7ULP_CLK_LPSPI2>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-sun6i.txt b/Documentation/devicetree/bindings/spi/spi-sun6i.txt index 21de73db6a05..2ec99b86b622 100644 --- a/Documentation/devicetree/bindings/spi/spi-sun6i.txt +++ b/Documentation/devicetree/bindings/spi/spi-sun6i.txt @@ -1,7 +1,7 @@ -Allwinner A31 SPI controller +Allwinner A31/H3 SPI controller Required properties: -- compatible: Should be "allwinner,sun6i-a31-spi". +- compatible: Should be "allwinner,sun6i-a31-spi" or "allwinner,sun8i-h3-spi". - reg: Should contain register location and length. - interrupts: Should contain interrupt. - clocks: phandle to the clocks feeding the SPI controller. Two are @@ -12,6 +12,11 @@ Required properties: - resets: phandle to the reset controller asserting this device in reset +Optional properties: +- dmas: DMA specifiers for rx and tx dma. See the DMA client binding, + Documentation/devicetree/bindings/dma/dma.txt +- dma-names: DMA request names should include "rx" and "tx" if present. + Example: spi1: spi@01c69000 { @@ -22,3 +27,19 @@ spi1: spi@01c69000 { clock-names = "ahb", "mod"; resets = <&ahb1_rst 21>; }; + +spi0: spi@01c68000 { + compatible = "allwinner,sun8i-h3-spi"; + reg = <0x01c68000 0x1000>; + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>; + clock-names = "ahb", "mod"; + dmas = <&dma 23>, <&dma 23>; + dma-names = "rx", "tx"; + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins>; + resets = <&ccu RST_BUS_SPI0>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/submitting-patches.txt b/Documentation/devicetree/bindings/submitting-patches.txt index 7d44eae7ab0b..274058c583dd 100644 --- a/Documentation/devicetree/bindings/submitting-patches.txt +++ b/Documentation/devicetree/bindings/submitting-patches.txt @@ -3,7 +3,7 @@ I. For patch submitters - 0) Normal patch submission rules from Documentation/SubmittingPatches + 0) Normal patch submission rules from Documentation/process/submitting-patches.rst applies. 1) The Documentation/ portion of the patch should be a separate patch. diff --git a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt index 08efe6bc2193..43003aec94bd 100644 --- a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt @@ -22,10 +22,13 @@ Required properties: TSADC controller. - pinctrl-2 : The "sleep" pinctrl state, it will be in for suspend. - #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description. + +Optional properties: - rockchip,hw-tshut-temp : The hardware-controlled shutdown temperature value. - rockchip,hw-tshut-mode : The hardware-controlled shutdown mode 0:CRU 1:GPIO. - rockchip,hw-tshut-polarity : The hardware-controlled active polarity 0:LOW 1:HIGH. +- rockchip,grf : The phandle of the syscon node for the general register file. Exiample: tsadc: tsadc@ff280000 { diff --git a/Documentation/devicetree/bindings/timer/ezchip,nps400-timer0.txt b/Documentation/devicetree/bindings/timer/ezchip,nps400-timer0.txt new file mode 100644 index 000000000000..e3cfce8fecc5 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/ezchip,nps400-timer0.txt @@ -0,0 +1,17 @@ +NPS Network Processor + +Required properties: + +- compatible : should be "ezchip,nps400-timer0" + +Clocks required for compatible = "ezchip,nps400-timer0": +- interrupts : The interrupt of the first timer +- clocks : Must contain a single entry describing the clock input + +Example: + +timer { + compatible = "ezchip,nps400-timer0"; + interrupts = <3>; + clocks = <&sysclk>; +}; diff --git a/Documentation/devicetree/bindings/timer/ezchip,nps400-timer.txt b/Documentation/devicetree/bindings/timer/ezchip,nps400-timer1.txt index c8c03d700382..c0ab4190b8fb 100644 --- a/Documentation/devicetree/bindings/timer/ezchip,nps400-timer.txt +++ b/Documentation/devicetree/bindings/timer/ezchip,nps400-timer1.txt @@ -2,14 +2,14 @@ NPS Network Processor Required properties: -- compatible : should be "ezchip,nps400-timer" +- compatible : should be "ezchip,nps400-timer1" -Clocks required for compatible = "ezchip,nps400-timer": +Clocks required for compatible = "ezchip,nps400-timer1": - clocks : Must contain a single entry describing the clock input Example: timer { - compatible = "ezchip,nps400-timer"; + compatible = "ezchip,nps400-timer1"; clocks = <&sysclk>; }; diff --git a/Documentation/devicetree/bindings/ufs/ufs-qcom.txt b/Documentation/devicetree/bindings/ufs/ufs-qcom.txt index 070baf4d7d97..b6b5130e5f65 100644 --- a/Documentation/devicetree/bindings/ufs/ufs-qcom.txt +++ b/Documentation/devicetree/bindings/ufs/ufs-qcom.txt @@ -7,8 +7,11 @@ To bind UFS PHY with UFS host controller, the controller node should contain a phandle reference to UFS PHY node. Required properties: -- compatible : compatible list, contains "qcom,ufs-phy-qmp-20nm" - or "qcom,ufs-phy-qmp-14nm" according to the relevant phy in use. +- compatible : compatible list, contains one of the following - + "qcom,ufs-phy-qmp-20nm" for 20nm ufs phy, + "qcom,ufs-phy-qmp-14nm" for legacy 14nm ufs phy, + "qcom,msm8996-ufs-phy-qmp-14nm" for 14nm ufs phy + present on MSM8996 chipset. - reg : should contain PHY register address space (mandatory), - reg-names : indicates various resources passed to driver (via reg proptery) by name. Required "reg-names" is "phy_mem". diff --git a/Documentation/devicetree/bindings/usb/da8xx-usb.txt b/Documentation/devicetree/bindings/usb/da8xx-usb.txt new file mode 100644 index 000000000000..ccb844aba7d4 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/da8xx-usb.txt @@ -0,0 +1,43 @@ +TI DA8xx MUSB +~~~~~~~~~~~~~ +For DA8xx/OMAP-L1x/AM17xx/AM18xx platforms. + +Required properties: +~~~~~~~~~~~~~~~~~~~~ + - compatible : Should be set to "ti,da830-musb". + + - reg: Offset and length of the USB controller register set. + + - interrupts: The USB interrupt number. + + - interrupt-names: Should be set to "mc". + + - dr_mode: The USB operation mode. Should be one of "host", "peripheral" or "otg". + + - phys: Phandle for the PHY device + + - phy-names: Should be "usb-phy" + +Optional properties: +~~~~~~~~~~~~~~~~~~~~ + - vbus-supply: Phandle to a regulator providing the USB bus power. + +Example: + usb_phy: usb-phy { + compatible = "ti,da830-usb-phy"; + #phy-cells = <0>; + status = "okay"; + }; + usb0: usb@200000 { + compatible = "ti,da830-musb"; + reg = <0x00200000 0x10000>; + interrupts = <58>; + interrupt-names = "mc"; + + dr_mode = "host"; + vbus-supply = <&usb_vbus>; + phys = <&usb_phy 0>; + phy-names = "usb-phy"; + + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt index 455f2c310a1b..6c7c2bce6d0c 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.txt +++ b/Documentation/devicetree/bindings/usb/dwc2.txt @@ -12,6 +12,7 @@ Required properties: - "lantiq,xrx200-usb": The DWC2 USB controller instance in Lantiq XRX SoCs; - "amlogic,meson8b-usb": The DWC2 USB controller instance in Amlogic Meson8b SoCs; - "amlogic,meson-gxbb-usb": The DWC2 USB controller instance in Amlogic S905 SoCs; + - "amcc,dwc-otg": The DWC2 USB controller instance in AMCC Canyonlands 460EX SoCs; - snps,dwc2: A generic DWC2 USB controller with default parameters. - reg : Should contain 1 register range (address and length) - interrupts : Should contain 1 interrupt @@ -25,13 +26,12 @@ Optional properties: Refer to phy/phy-bindings.txt for generic phy consumer properties - dr_mode: shall be one of "host", "peripheral" and "otg" Refer to usb/generic.txt -- g-use-dma: enable dma usage in gadget driver. - g-rx-fifo-size: size of rx fifo size in gadget mode. - g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget mode. +- g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode. Deprecated properties: -- g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) - in gadget mode. +- g-use-dma: gadget DMA mode is automatically detected Example: diff --git a/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt b/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt new file mode 100644 index 000000000000..e049d199bf0d --- /dev/null +++ b/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt @@ -0,0 +1,87 @@ +The device node for Mediatek USB3.0 DRD controller + +Required properties: + - compatible : should be "mediatek,mt8173-mtu3" + - reg : specifies physical base address and size of the registers + - reg-names: should be "mac" for device IP and "ippc" for IP port control + - interrupts : interrupt used by the device IP + - power-domains : a phandle to USB power domain node to control USB's + mtcmos + - vusb33-supply : regulator of USB avdd3.3v + - clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock-names + - clock-names : must contain "sys_ck" for clock of controller; + "wakeup_deb_p0" and "wakeup_deb_p1" are optional, they are + depends on "mediatek,enable-wakeup" + - phys : a list of phandle + phy specifier pairs + - dr_mode : should be one of "host", "peripheral" or "otg", + refer to usb/generic.txt + +Optional properties: + - #address-cells, #size-cells : should be '2' if the device has sub-nodes + with 'reg' property + - ranges : allows valid 1:1 translation between child's address space and + parent's address space + - extcon : external connector for vbus and idpin changes detection, needed + when supports dual-role mode. + - vbus-supply : reference to the VBUS regulator, needed when supports + dual-role mode. + - pinctl-names : a pinctrl state named "default" must be defined, + "id_float" and "id_ground" are optinal which depends on + "mediatek,enable-manual-drd" + - pinctrl-0 : pin control group + See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt + + - maximum-speed : valid arguments are "super-speed", "high-speed" and + "full-speed"; refer to usb/generic.txt + - enable-manual-drd : supports manual dual-role switch via debugfs; usually + used when receptacle is TYPE-A and also wants to support dual-role + mode. + - mediatek,enable-wakeup : supports ip sleep wakeup used by host mode + - mediatek,syscon-wakeup : phandle to syscon used to access USB wakeup + control register, it depends on "mediatek,enable-wakeup". + +Sub-nodes: +The xhci should be added as subnode to mtu3 as shown in the following example +if host mode is enabled. The DT binding details of xhci can be found in: +Documentation/devicetree/bindings/usb/mt8173-xhci.txt + +Example: +ssusb: usb@11271000 { + compatible = "mediatek,mt8173-mtu3"; + reg = <0 0x11271000 0 0x3000>, + <0 0x11280700 0 0x0100>; + reg-names = "mac", "ippc"; + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>; + phys = <&phy_port0 PHY_TYPE_USB3>, + <&phy_port1 PHY_TYPE_USB2>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; + clocks = <&topckgen CLK_TOP_USB30_SEL>, + <&pericfg CLK_PERI_USB0>, + <&pericfg CLK_PERI_USB1>; + clock-names = "sys_ck", + "wakeup_deb_p0", + "wakeup_deb_p1"; + vusb33-supply = <&mt6397_vusb_reg>; + vbus-supply = <&usb_p0_vbus>; + extcon = <&extcon_usb>; + dr_mode = "otg"; + mediatek,enable-wakeup; + mediatek,syscon-wakeup = <&pericfg>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + + usb_host: xhci@11270000 { + compatible = "mediatek,mt8173-xhci"; + reg = <0 0x11270000 0 0x1000>; + reg-names = "mac"; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; + clocks = <&topckgen CLK_TOP_USB30_SEL>; + clock-names = "sys_ck"; + vusb33-supply = <&mt6397_vusb_reg>; + status = "disabled"; + }; +}; diff --git a/Documentation/devicetree/bindings/usb/mt8173-xhci.txt b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt index b3a7ffa48852..2a930bd52b94 100644 --- a/Documentation/devicetree/bindings/usb/mt8173-xhci.txt +++ b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt @@ -2,10 +2,18 @@ MT8173 xHCI The device node for Mediatek SOC USB3.0 host controller +There are two scenarios: the first one only supports xHCI driver; +the second one supports dual-role mode, and the host is based on xHCI +driver. Take account of backward compatibility, we divide bindings +into two parts. + +1st: only supports xHCI driver +------------------------------------------------------------------------ + Required properties: - compatible : should contain "mediatek,mt8173-xhci" - - reg : specifies physical base address and size of the registers, - the first one for MAC, the second for IPPC + - reg : specifies physical base address and size of the registers + - reg-names: should be "mac" for xHCI MAC and "ippc" for IP port control - interrupts : interrupt used by the controller - power-domains : a phandle to USB power domain node to control USB's mtcmos @@ -27,12 +35,16 @@ Optional properties: control register, it depends on "mediatek,wakeup-src". - vbus-supply : reference to the VBUS regulator; - usb3-lpm-capable : supports USB3.0 LPM + - pinctrl-names : a pinctrl state named "default" must be defined + - pinctrl-0 : pin control group + See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt Example: usb30: usb@11270000 { compatible = "mediatek,mt8173-xhci"; reg = <0 0x11270000 0 0x1000>, <0 0x11280700 0 0x0100>; + reg-names = "mac", "ippc"; interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; clocks = <&topckgen CLK_TOP_USB30_SEL>, @@ -49,3 +61,41 @@ usb30: usb@11270000 { mediatek,syscon-wakeup = <&pericfg>; mediatek,wakeup-src = <1>; }; + +2nd: dual-role mode with xHCI driver +------------------------------------------------------------------------ + +In the case, xhci is added as subnode to mtu3. An example and the DT binding +details of mtu3 can be found in: +Documentation/devicetree/bindings/usb/mtu3.txt + +Required properties: + - compatible : should contain "mediatek,mt8173-xhci" + - reg : specifies physical base address and size of the registers + - reg-names: should be "mac" for xHCI MAC + - interrupts : interrupt used by the host controller + - power-domains : a phandle to USB power domain node to control USB's + mtcmos + - vusb33-supply : regulator of USB avdd3.3v + + - clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock-names + - clock-names : must be + "sys_ck": for clock of xHCI MAC + +Optional properties: + - vbus-supply : reference to the VBUS regulator; + - usb3-lpm-capable : supports USB3.0 LPM + +Example: +usb30: usb@11270000 { + compatible = "mediatek,mt8173-xhci"; + reg = <0 0x11270000 0 0x1000>; + reg-names = "mac"; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; + clocks = <&topckgen CLK_TOP_USB30_SEL>; + clock-names = "sys_ck"; + vusb33-supply = <&mt6397_vusb_reg>; + usb3-lpm-capable; +}; diff --git a/Documentation/devicetree/bindings/usb/ohci-da8xx.txt b/Documentation/devicetree/bindings/usb/ohci-da8xx.txt new file mode 100644 index 000000000000..2dc8f67eda39 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ohci-da8xx.txt @@ -0,0 +1,23 @@ +DA8XX USB OHCI controller + +Required properties: + + - compatible: Should be "ti,da830-ohci" + - reg: Should contain one register range i.e. start and length + - interrupts: Description of the interrupt line + - phys: Phandle for the PHY device + - phy-names: Should be "usb-phy" + +Optional properties: + - vbus-supply: phandle of regulator that controls vbus power / over-current + +Example: + +ohci: usb@0225000 { + compatible = "ti,da830-ohci"; + reg = <0x225000 0x1000>; + interrupts = <59>; + phys = <&usb_phy 1>; + phy-names = "usb-phy"; + vbus-supply = <®_usb_ohci>; +}; diff --git a/Documentation/devicetree/bindings/usb/s3c2410-usb.txt b/Documentation/devicetree/bindings/usb/s3c2410-usb.txt new file mode 100644 index 000000000000..e45b38ce2986 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/s3c2410-usb.txt @@ -0,0 +1,22 @@ +Samsung S3C2410 and compatible SoC USB controller + +OHCI + +Required properties: + - compatible: should be "samsung,s3c2410-ohci" for USB host controller + - reg: address and lenght of the controller memory mapped region + - interrupts: interrupt number for the USB OHCI controller + - clocks: Should reference the bus and host clocks + - clock-names: Should contain two strings + "usb-bus-host" for the USB bus clock + "usb-host" for the USB host clock + +Example: + +usb0: ohci@49000000 { + compatible = "samsung,s3c2410-ohci"; + reg = <0x49000000 0x100>; + interrupts = <0 0 26 3>; + clocks = <&clocks UCLK>, <&clocks HCLK_USBH>; + clock-names = "usb-bus-host", "usb-host"; +}; diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt index 966885c636d0..0b7d8576001c 100644 --- a/Documentation/devicetree/bindings/usb/usb-xhci.txt +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -11,6 +11,7 @@ Required properties: - "renesas,xhci-r8a7791" for r8a7791 SoC - "renesas,xhci-r8a7793" for r8a7793 SoC - "renesas,xhci-r8a7795" for r8a7795 SoC + - "renesas,xhci-r8a7796" for r8a7796 SoC - "renesas,rcar-gen2-xhci" for a generic R-Car Gen2 compatible device - "renesas,rcar-gen3-xhci" for a generic R-Car Gen3 compatible device - "xhci-platform" (deprecated) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index f0a48ea78659..6e25c912a5c2 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -24,9 +24,11 @@ ampire Ampire Co., Ltd. ams AMS AG amstaos AMS-Taos Inc. analogix Analogix Semiconductor, Inc. +andestech Andes Technology Corporation apm Applied Micro Circuits Corporation (APM) aptina Aptina Imaging arasan Arasan Chip Systems +aries Aries Embedded GmbH arm ARM Ltd. armadeus ARMadeus Systems SARL arrow Arrow Electronics @@ -39,6 +41,7 @@ auo AU Optronics Corporation auvidea Auvidea GmbH avago Avago Technologies avic Shanghai AVIC Optoelectronics Co., Ltd. +axentia Axentia Technologies AB axis Axis Communications AB boe BOE Technology Group Co., Ltd. bosch Bosch Sensortec GmbH @@ -126,6 +129,7 @@ hitex Hitex Development Tools holt Holt Integrated Circuits, Inc. honeywell Honeywell hp Hewlett Packard +holtek Holtek Semiconductor, Inc. i2se I2SE GmbH ibm International Business Machines (IBM) idt Integrated Device Technologies, Inc. @@ -135,6 +139,7 @@ infineon Infineon Technologies inforce Inforce Computing ingenic Ingenic Semiconductor innolux Innolux Corporation +inside-secure INSIDE Secure intel Intel Corporation intercontrol Inter Control Group invensense InvenSense Inc. @@ -158,18 +163,22 @@ lg LG Corporation linux Linux-specific binding lltc Linear Technology Corporation lsi LSI Corp. (LSI Logic) +macnica Macnica Americas marvell Marvell Technology Group Ltd. maxim Maxim Integrated Products +mcube mCube meas Measurement Specialties mediatek MediaTek Inc. melexis Melexis N.V. melfas MELFAS Inc. +memsic MEMSIC Inc. merrii Merrii Technology Co., Ltd. micrel Micrel Inc. microchip Microchip Technology Inc. microcrystal Micro Crystal AG micron Micron Technology Inc. minix MINIX Technology Ltd. +miramems MiraMEMS Sensing Technology Co., Ltd. mitsubishi Mitsubishi Electric Corporation mosaixtech Mosaix Technologies, Inc. moxa Moxa @@ -180,6 +189,7 @@ mti Imagination Technologies Ltd. (formerly MIPS Technologies Inc.) mundoreader Mundo Reader S.L. murata Murata Manufacturing Co., Ltd. mxicy Macronix International Co., Ltd. +myir MYIR Tech Limited national National Semiconductor nec NEC LCD Technologies, Ltd. neonode Neonode Inc. @@ -187,12 +197,15 @@ netgear NETGEAR netlogic Broadcom Corporation (formerly NetLogic Microsystems) netxeon Shenzhen Netxeon Technology CO., LTD newhaven Newhaven Display International +ni National Instruments nintendo Nintendo nokia Nokia nuvoton Nuvoton Technology Corporation +nvd New Vision Display nvidia NVIDIA nxp NXP Semiconductors okaya Okaya Electric America, Inc. +oki Oki Electric Industry Co., Ltd. olimex OLIMEX Ltd. onion Onion Corporation onnn ON Semiconductor Corp. @@ -231,6 +244,7 @@ richtek Richtek Technology Corporation ricoh Ricoh Co. Ltd. rockchip Fuzhou Rockchip Electronics Co., Ltd samsung Samsung Semiconductor +samtec Samtec/Softing company sandisk Sandisk Corporation sbs Smart Battery System schindler Schindler @@ -275,6 +289,7 @@ tcg Trusted Computing Group tcl Toby Churchill Ltd. technexion TechNexion technologic Technologic Systems +terasic Terasic Inc. thine THine Electronics, Inc. ti Texas Instruments tlm Trusted Logic Mobility @@ -289,6 +304,7 @@ tronfy Tronfy tronsmart Tronsmart truly Truly Semiconductors Limited tyan Tyan Computer Corporation +udoo Udoo uniwest United Western Technologies Corp (UniWest) upisemi uPI Semiconductor Corp. urt United Radiant Technology Corporation diff --git a/Documentation/devicetree/bindings/video/bridge/sil-sii8620.txt b/Documentation/devicetree/bindings/video/bridge/sil-sii8620.txt new file mode 100644 index 000000000000..9409d9c6a260 --- /dev/null +++ b/Documentation/devicetree/bindings/video/bridge/sil-sii8620.txt @@ -0,0 +1,33 @@ +Silicon Image SiI8620 HDMI/MHL bridge bindings + +Required properties: + - compatible: "sil,sii8620" + - reg: i2c address of the bridge + - cvcc10-supply: Digital Core Supply Voltage (1.0V) + - iovcc18-supply: I/O Supply Voltage (1.8V) + - interrupts, interrupt-parent: interrupt specifier of INT pin + - reset-gpios: gpio specifier of RESET pin + - clocks, clock-names: specification and name of "xtal" clock + - video interfaces: Device node can contain video interface port + node for HDMI encoder according to [1]. + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + sii8620@39 { + reg = <0x39>; + compatible = "sil,sii8620"; + cvcc10-supply = <&ldo36_reg>; + iovcc18-supply = <&ldo34_reg>; + interrupt-parent = <&gpf0>; + interrupts = <2 0>; + reset-gpio = <&gpv7 0 0>; + clocks = <&pmu_system_controller 0>; + clock-names = "xtal"; + + port { + mhl_to_hdmi: endpoint { + remote-endpoint = <&hdmi_to_mhl>; + }; + }; + }; diff --git a/Documentation/devicetree/booting-without-of.txt b/Documentation/devicetree/booting-without-of.txt index 3f1437fbca6b..280d283304bb 100644 --- a/Documentation/devicetree/booting-without-of.txt +++ b/Documentation/devicetree/booting-without-of.txt @@ -974,6 +974,13 @@ compatibility. 4Gb. Some vendors prefer splitting those ranges into smaller segments, but the kernel doesn't care. + Additional properties: + + - hotpluggable : The presence of this property provides an explicit + hint to the operating system that this memory may potentially be + removed later. The kernel can take this into consideration when + doing nonmovable allocations and when laying out memory zones. + e) The /chosen node This node is a bit "special". Normally, that's where Open Firmware |