diff options
Diffstat (limited to 'Documentation/devicetree')
11 files changed, 298 insertions, 26 deletions
diff --git a/Documentation/devicetree/bindings/iio/dac/ad7303.txt b/Documentation/devicetree/bindings/iio/dac/ad7303.txt new file mode 100644 index 000000000000..914610f0556e --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/ad7303.txt @@ -0,0 +1,23 @@ +Analog Devices AD7303 DAC device driver + +Required properties: + - compatible: Must be "adi,ad7303" + - reg: SPI chip select number for the device + - spi-max-frequency: Max SPI frequency to use (< 30000000) + - Vdd-supply: Phandle to the Vdd power supply + +Optional properties: + - REF-supply: Phandle to the external reference voltage supply. This should + only be set if there is an external reference voltage connected to the REF + pin. If the property is not set Vdd/2 is used as the reference voltage. + +Example: + + ad7303@4 { + compatible = "adi,ad7303"; + reg = <4>; + spi-max-frequency = <10000000>; + Vdd-supply = <&vdd_supply>; + adi,use-external-reference; + REF-supply = <&vref_supply>; + }; diff --git a/Documentation/devicetree/bindings/iio/frequency/adf4350.txt b/Documentation/devicetree/bindings/iio/frequency/adf4350.txt new file mode 100644 index 000000000000..f8c181d81d2d --- /dev/null +++ b/Documentation/devicetree/bindings/iio/frequency/adf4350.txt @@ -0,0 +1,86 @@ +Analog Devices ADF4350/ADF4351 device driver + +Required properties: + - compatible: Should be one of + * "adi,adf4350": When using the ADF4350 device + * "adi,adf4351": When using the ADF4351 device + - reg: SPI chip select numbert for the device + - spi-max-frequency: Max SPI frequency to use (< 20000000) + - clocks: From common clock binding. Clock is phandle to clock for + ADF435x Reference Clock (CLKIN). + +Optional properties: + - gpios: GPIO Lock detect - If set with a valid phandle and GPIO number, + pll lock state is tested upon read. + - adi,channel-spacing: Channel spacing in Hz (influences MODULUS). + - adi,power-up-frequency: If set in Hz the PLL tunes to + the desired frequency on probe. + - adi,reference-div-factor: If set the driver skips dynamic calculation + and uses this default value instead. + - adi,reference-doubler-enable: Enables reference doubler. + - adi,reference-div2-enable: Enables reference divider. + - adi,phase-detector-polarity-positive-enable: Enables positive phase + detector polarity. Default = negative. + - adi,lock-detect-precision-6ns-enable: Enables 6ns lock detect precision. + Default = 10ns. + - adi,lock-detect-function-integer-n-enable: Enables lock detect + for integer-N mode. Default = factional-N mode. + - adi,charge-pump-current: Charge pump current in mA. + Default = 2500mA. + - adi,muxout-select: On chip multiplexer output selection. + Valid values for the multiplexer output are: + 0: Three-State Output (default) + 1: DVDD + 2: DGND + 3: R-Counter output + 4: N-Divider output + 5: Analog lock detect + 6: Digital lock detect + - adi,low-spur-mode-enable: Enables low spur mode. + Default = Low noise mode. + - adi,cycle-slip-reduction-enable: Enables cycle slip reduction. + - adi,charge-cancellation-enable: Enabled charge pump + charge cancellation for integer-N modes. + - adi,anti-backlash-3ns-enable: Enables 3ns antibacklash pulse width + for integer-N modes. + - adi,band-select-clock-mode-high-enable: Enables faster band + selection logic. + - adi,12bit-clk-divider: Clock divider value used when + adi,12bit-clkdiv-mode != 0 + - adi,clk-divider-mode: + Valid values for the clkdiv mode are: + 0: Clock divider off (default) + 1: Fast lock enable + 2: Phase resync enable + - adi,aux-output-enable: Enables auxiliary RF output. + - adi,aux-output-fundamental-enable: Selects fundamental VCO output on + the auxiliary RF output. Default = Output of RF dividers. + - adi,mute-till-lock-enable: Enables Mute-Till-Lock-Detect function. + - adi,output-power: Output power selection. + Valid values for the power mode are: + 0: -4dBm (default) + 1: -1dBm + 2: +2dBm + 3: +5dBm + - adi,aux-output-power: Auxiliary output power selection. + Valid values for the power mode are: + 0: -4dBm (default) + 1: -1dBm + 2: +2dBm + 3: +5dBm + + +Example: + lo_pll0_rx_adf4351: adf4351-rx-lpc@4 { + compatible = "adi,adf4351"; + reg = <4>; + spi-max-frequency = <10000000>; + clocks = <&clk0_ad9523 9>; + clock-names = "clkin"; + adi,channel-spacing = <10000>; + adi,power-up-frequency = <2400000000>; + adi,phase-detector-polarity-positive-enable; + adi,charge-pump-current = <2500>; + adi,output-power = <3>; + adi,mute-till-lock-enable; + }; diff --git a/Documentation/devicetree/bindings/iio/magnetometer/ak8975.txt b/Documentation/devicetree/bindings/iio/magnetometer/ak8975.txt new file mode 100644 index 000000000000..011679f1a425 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/magnetometer/ak8975.txt @@ -0,0 +1,18 @@ +* AsahiKASEI AK8975 magnetometer sensor + +Required properties: + + - compatible : should be "asahi-kasei,ak8975" + - reg : the I2C address of the magnetometer + +Optional properties: + + - gpios : should be device tree identifier of the magnetometer DRDY pin + +Example: + +ak8975@0c { + compatible = "asahi-kasei,ak8975"; + reg = <0x0c>; + gpios = <&gpj0 7 0>; +}; diff --git a/Documentation/devicetree/bindings/media/exynos-fimc-lite.txt b/Documentation/devicetree/bindings/media/exynos-fimc-lite.txt index 3f62adfb3e0b..de9f6b78ee51 100644 --- a/Documentation/devicetree/bindings/media/exynos-fimc-lite.txt +++ b/Documentation/devicetree/bindings/media/exynos-fimc-lite.txt @@ -2,7 +2,7 @@ Exynos4x12/Exynos5 SoC series camera host interface (FIMC-LITE) Required properties: -- compatible : should be "samsung,exynos4212-fimc" for Exynos4212 and +- compatible : should be "samsung,exynos4212-fimc-lite" for Exynos4212 and Exynos4412 SoCs; - reg : physical base address and size of the device memory mapped registers; diff --git a/Documentation/devicetree/bindings/staging/imx-drm/ldb.txt b/Documentation/devicetree/bindings/staging/imx-drm/ldb.txt new file mode 100644 index 000000000000..ed9377811ee2 --- /dev/null +++ b/Documentation/devicetree/bindings/staging/imx-drm/ldb.txt @@ -0,0 +1,99 @@ +Device-Tree bindings for LVDS Display Bridge (ldb) + +LVDS Display Bridge +=================== + +The LVDS Display Bridge device tree node contains up to two lvds-channel +nodes describing each of the two LVDS encoder channels of the bridge. + +Required properties: + - #address-cells : should be <1> + - #size-cells : should be <0> + - compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb". + Both LDB versions are similar, but i.MX6 has an additional + multiplexer in the front to select any of the four IPU display + interfaces as input for each LVDS channel. + - gpr : should be <&gpr> on i.MX53 and i.MX6q. + The phandle points to the iomuxc-gpr region containing the LVDS + control register. +- clocks, clock-names : phandles to the LDB divider and selector clocks and to + the display interface selector clocks, as described in + Documentation/devicetree/bindings/clock/clock-bindings.txt + The following clocks are expected on i.MX53: + "di0_pll" - LDB LVDS channel 0 mux + "di1_pll" - LDB LVDS channel 1 mux + "di0" - LDB LVDS channel 0 gate + "di1" - LDB LVDS channel 1 gate + "di0_sel" - IPU1 DI0 mux + "di1_sel" - IPU1 DI1 mux + On i.MX6q the following additional clocks are needed: + "di2_sel" - IPU2 DI0 mux + "di3_sel" - IPU2 DI1 mux + The needed clock numbers for each are documented in + Documentation/devicetree/bindings/clock/imx5-clock.txt, and in + Documentation/devicetree/bindings/clock/imx6q-clock.txt. + +Optional properties: + - pinctrl-names : should be "default" on i.MX53, not used on i.MX6q + - pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53, + not used on i.MX6q + - fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should + be configured - one input will be distributed on both outputs in dual + channel mode + +LVDS Channel +============ + +Each LVDS Channel has to contain a display-timings node that describes the +video timings for the connected LVDS display. For detailed information, also +have a look at Documentation/devicetree/bindings/video/display-timing.txt. + +Required properties: + - reg : should be <0> or <1> + - crtcs : a list of phandles with index pointing to the IPU display interfaces + that can be used as video source for this channel. + - fsl,data-mapping : should be "spwg" or "jeida" + This describes how the color bits are laid out in the + serialized LVDS signal. + - fsl,data-width : should be <18> or <24> + +example: + +gpr: iomuxc-gpr@53fa8000 { + /* ... */ +}; + +ldb: ldb@53fa8008 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx53-ldb"; + gpr = <&gpr>; + clocks = <&clks 122>, <&clks 120>, + <&clks 115>, <&clks 116>, + <&clks 123>, <&clks 85>; + clock-names = "di0_pll", "di1_pll", + "di0_sel", "di1_sel", + "di0", "di1"; + + lvds-channel@0 { + reg = <0>; + crtcs = <&ipu 0>; + fsl,data-mapping = "spwg"; + fsl,data-width = <24>; + + display-timings { + /* ... */ + }; + }; + + lvds-channel@1 { + reg = <1>; + crtcs = <&ipu 1>; + fsl,data-mapping = "spwg"; + fsl,data-width = <24>; + + display-timings { + /* ... */ + }; + }; +}; diff --git a/Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt index b462d0c54823..c662eb36be29 100644 --- a/Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt +++ b/Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt @@ -8,6 +8,8 @@ Required properties: Optional properties: - fsl,uart-has-rtscts : Indicate the uart has rts and cts - fsl,irda-mode : Indicate the uart supports irda mode +- fsl,dte-mode : Indicate the uart works in DTE mode. The uart works + is DCE mode by default. Example: @@ -16,4 +18,5 @@ serial@73fbc000 { reg = <0x73fbc000 0x4000>; interrupts = <31>; fsl,uart-has-rtscts; + fsl,dte-mode; }; diff --git a/Documentation/devicetree/bindings/tty/serial/fsl-lpuart.txt b/Documentation/devicetree/bindings/tty/serial/fsl-lpuart.txt new file mode 100644 index 000000000000..6fd1dd1638dd --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/fsl-lpuart.txt @@ -0,0 +1,14 @@ +* Freescale low power universal asynchronous receiver/transmitter (lpuart) + +Required properties: +- compatible : Should be "fsl,<soc>-lpuart" +- reg : Address and length of the register set for the device +- interrupts : Should contain uart interrupt + +Example: + +uart0: serial@40027000 { + compatible = "fsl,vf610-lpuart"; + reg = <0x40027000 0x1000>; + interrupts = <0 61 0x00>; + }; diff --git a/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt b/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt index 1c04a4c9515f..b4b5b7906c88 100644 --- a/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt +++ b/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt @@ -5,6 +5,12 @@ Required properties: - reg: Should contain registers location and length - interrupts: Should contain controller interrupt +Recommended properies: +- phy_type: the type of the phy connected to the core. Should be one + of "utmi", "utmi_wide", "ulpi", "serial" or "hsic". Without this + property the PORTSC register won't be touched +- dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg" + Optional properties: - fsl,usbphy: phandler of usb phy that connects to the only one port - fsl,usbmisc: phandler of non-core register device, with one argument diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt index 34c952883276..df0933043a5b 100644 --- a/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt @@ -6,27 +6,10 @@ Practice : Universal Serial Bus" with the following modifications and additions : Required properties : - - compatible : Should be "nvidia,tegra20-ehci" for USB controllers - used in host mode. - - phy_type : Should be one of "ulpi" or "utmi". - - nvidia,vbus-gpio : If present, specifies a gpio that needs to be - activated for the bus to be powered. - - nvidia,phy : phandle of the PHY instance, the controller is connected to. - -Required properties for phy_type == ulpi: - - nvidia,phy-reset-gpio : The GPIO used to reset the PHY. + - compatible : Should be "nvidia,tegra20-ehci". + - nvidia,phy : phandle of the PHY that the controller is connected to. + - clocks : Contains a single entry which defines the USB controller's clock. Optional properties: - - dr_mode : dual role mode. Indicates the working mode for - nvidia,tegra20-ehci compatible controllers. Can be "host", "peripheral", - or "otg". Default to "host" if not defined for backward compatibility. - host means this is a host controller - peripheral means it is device controller - otg means it can operate as either ("on the go") - - nvidia,has-legacy-mode : boolean indicates whether this controller can - operate in legacy mode (as APX 2500 / 2600). In legacy mode some - registers are accessed through the APB_MISC base address instead of - the USB controller. Since this is a legacy issue it probably does not - warrant a compatible string of its own. - - nvidia,needs-double-reset : boolean is to be set for some of the Tegra2 - USB ports, which need reset twice due to hardware issues. + - nvidia,needs-double-reset : boolean is to be set for some of the Tegra20 + USB ports, which need reset twice due to hardware issues. diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt index 6bdaba2f0aa1..c4c9e9e664aa 100644 --- a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt @@ -4,14 +4,49 @@ The device node for Tegra SOC USB PHY: Required properties : - compatible : Should be "nvidia,tegra20-usb-phy". - - reg : Address and length of the register set for the USB PHY interface. - - phy_type : Should be one of "ulpi" or "utmi". + - reg : Defines the following set of registers, in the order listed: + - The PHY's own register set. + Always present. + - The register set of the PHY containing the UTMI pad control registers. + Present if-and-only-if phy_type == utmi. + - phy_type : Should be one of "utmi", "ulpi" or "hsic". + - clocks : Defines the clocks listed in the clock-names property. + - clock-names : The following clock names must be present: + - reg: The clock needed to access the PHY's own registers. This is the + associated EHCI controller's clock. Always present. + - pll_u: PLL_U. Always present. + - timer: The timeout clock (clk_m). Present if phy_type == utmi. + - utmi-pads: The clock needed to access the UTMI pad control registers. + Present if phy_type == utmi. + - ulpi-link: The clock Tegra provides to the ULPI PHY (cdev2). + Present if phy_type == ulpi, and ULPI link mode is in use. Required properties for phy_type == ulpi: - nvidia,phy-reset-gpio : The GPIO used to reset the PHY. +Required PHY timing params for utmi phy: + - nvidia,hssync-start-delay : Number of 480 Mhz clock cycles to wait before + start of sync launches RxActive + - nvidia,elastic-limit : Variable FIFO Depth of elastic input store + - nvidia,idle-wait-delay : Number of 480 Mhz clock cycles of idle to wait + before declare IDLE. + - nvidia,term-range-adj : Range adjusment on terminations + - nvidia,xcvr-setup : HS driver output control + - nvidia,xcvr-lsfslew : LS falling slew rate control. + - nvidia,xcvr-lsrslew : LS rising slew rate control. + Optional properties: - nvidia,has-legacy-mode : boolean indicates whether this controller can operate in legacy mode (as APX 2500 / 2600). In legacy mode some registers are accessed through the APB_MISC base address instead of - the USB controller.
\ No newline at end of file + the USB controller. + - nvidia,is-wired : boolean. Indicates whether we can do certain kind of power + optimizations for the devices that are always connected. e.g. modem. + - dr_mode : dual role mode. Indicates the working mode for the PHY. Can be + "host", "peripheral", or "otg". Defaults to "host" if not defined. + host means this is a host controller + peripheral means it is device controller + otg means it can operate as either ("on the go") + +Required properties for dr_mode == otg: + - vbus-supply: regulator for VBUS diff --git a/Documentation/devicetree/bindings/usb/usb3503.txt b/Documentation/devicetree/bindings/usb/usb3503.txt index 6813a715fc7d..8c5be48b43c8 100644 --- a/Documentation/devicetree/bindings/usb/usb3503.txt +++ b/Documentation/devicetree/bindings/usb/usb3503.txt @@ -4,6 +4,10 @@ Required properties: - compatible: Should be "smsc,usb3503". - reg: Specifies the i2c slave address, it should be 0x08. - connect-gpios: Should specify GPIO for connect. +- disabled-ports: Should specify the ports unused. + '1' or '2' or '3' are availe for this property to describe the port + number. 1~3 property values are possible to be desribed. + Do not describe this property if all ports have to be enabled. - intn-gpios: Should specify GPIO for interrupt. - reset-gpios: Should specify GPIO for reset. - initial-mode: Should specify initial mode. @@ -14,6 +18,7 @@ Examples: compatible = "smsc,usb3503"; reg = <0x08>; connect-gpios = <&gpx3 0 1>; + disabled-ports = <2 3>; intn-gpios = <&gpx3 4 1>; reset-gpios = <&gpx3 5 1>; initial-mode = <1>; |