1 files changed, 0 insertions, 138 deletions
diff --git a/Documentation/hwmon/f71882fg b/Documentation/hwmon/f71882fg
deleted file mode 100644
index 4c3cb8377d74..000000000000
--- a/Documentation/hwmon/f71882fg
+++ /dev/null
@@ -1,138 +0,0 @@
-Kernel driver f71882fg
-======================
-
-Supported chips:
-  * Fintek F71808E
-    Prefix: 'f71808e'
-    Addresses scanned: none, address read from Super I/O config space
-    Datasheet: Not public
-  * Fintek F71808A
-    Prefix: 'f71808a'
-    Addresses scanned: none, address read from Super I/O config space
-    Datasheet: Not public
-  * Fintek F71858FG
-    Prefix: 'f71858fg'
-    Addresses scanned: none, address read from Super I/O config space
-    Datasheet: Available from the Fintek website
-  * Fintek F71862FG and F71863FG
-    Prefix: 'f71862fg'
-    Addresses scanned: none, address read from Super I/O config space
-    Datasheet: Available from the Fintek website
-  * Fintek F71869F and F71869E
-    Prefix: 'f71869'
-    Addresses scanned: none, address read from Super I/O config space
-    Datasheet: Available from the Fintek website
-  * Fintek F71869A
-    Prefix: 'f71869a'
-    Addresses scanned: none, address read from Super I/O config space
-    Datasheet: Not public
-  * Fintek F71882FG and F71883FG
-    Prefix: 'f71882fg'
-    Addresses scanned: none, address read from Super I/O config space
-    Datasheet: Available from the Fintek website
-  * Fintek F71889FG
-    Prefix: 'f71889fg'
-    Addresses scanned: none, address read from Super I/O config space
-    Datasheet: Available from the Fintek website
-  * Fintek F71889ED
-    Prefix: 'f71889ed'
-    Addresses scanned: none, address read from Super I/O config space
-    Datasheet: Should become available on the Fintek website soon
-  * Fintek F71889A
-    Prefix: 'f71889a'
-    Addresses scanned: none, address read from Super I/O config space
-    Datasheet: Should become available on the Fintek website soon
-  * Fintek F8000
-    Prefix: 'f8000'
-    Addresses scanned: none, address read from Super I/O config space
-    Datasheet: Not public
-  * Fintek F81801U
-    Prefix: 'f71889fg'
-    Addresses scanned: none, address read from Super I/O config space
-    Datasheet: Not public
-    Note: This is the 64-pin variant of the F71889FG, they have the
-	  same device ID and are fully compatible as far as hardware
-	  monitoring is concerned.
-  * Fintek F81865F
-    Prefix: 'f81865f'
-    Addresses scanned: none, address read from Super I/O config space
-    Datasheet: Available from the Fintek website
-
-Author: Hans de Goede <hdegoede@redhat.com>
-
-
-Description
------------
-
-Fintek F718xx/F8000 Super I/O chips include complete hardware monitoring
-capabilities. They can monitor up to 9 voltages, 4 fans and 3 temperature
-sensors.
-
-These chips also have fan controlling features, using either DC or PWM, in
-three different modes (one manual, two automatic).
-
-The driver assumes that no more than one chip is present, which seems
-reasonable.
-
-
-Monitoring
-----------
-
-The Voltage, Fan and Temperature Monitoring uses the standard sysfs
-interface as documented in sysfs-interface, without any exceptions.
-
-
-Fan Control
------------
-
-Both PWM (pulse-width modulation) and DC fan speed control methods are
-supported. The right one to use depends on external circuitry on the
-motherboard, so the driver assumes that the BIOS set the method
-properly.
-
-Note that the lowest numbered temperature zone trip point corresponds to
-to the border between the highest and one but highest temperature zones, and
-vica versa. So the temperature zone trip points 1-4 (or 1-2) go from high temp
-to low temp! This is how things are implemented in the IC, and the driver
-mimics this.
-
-There are 2 modes to specify the speed of the fan, PWM duty cycle (or DC
-voltage) mode, where 0-100% duty cycle (0-100% of 12V) is specified. And RPM
-mode where the actual RPM of the fan (as measured) is controlled and the speed
-gets specified as 0-100% of the fan#_full_speed file.
-
-Since both modes work in a 0-100% (mapped to 0-255) scale, there isn't a
-whole lot of a difference when modifying fan control settings. The only
-important difference is that in RPM mode the 0-100% controls the fan speed
-between 0-100% of fan#_full_speed. It is assumed that if the BIOS programs
-RPM mode, it will also set fan#_full_speed properly, if it does not then
-fan control will not work properly, unless you set a sane fan#_full_speed
-value yourself.
-
-Switching between these modes requires re-initializing a whole bunch of
-registers, so the mode which the BIOS has set is kept. The mode is
-printed when loading the driver.
-
-Three different fan control modes are supported; the mode number is written
-to the pwm#_enable file. Note that not all modes are supported on all
-chips, and some modes may only be available in RPM / PWM mode.
-Writing an unsupported mode will result in an invalid parameter error.
-
-* 1: Manual mode
-  You ask for a specific PWM duty cycle / DC voltage or a specific % of
-  fan#_full_speed by writing to the pwm# file. This mode is only
-  available on the F71858FG / F8000 if the fan channel is in RPM mode.
-
-* 2: Normal auto mode
-  You can define a number of temperature/fan speed trip points, which % the
-  fan should run at at this temp and which temp a fan should follow using the
-  standard sysfs interface. The number and type of trip points is chip
-  depended, see which files are available in sysfs.
-  Fan/PWM channel 3 of the F8000 is always in this mode!
-
-* 3: Thermostat mode (Only available on the F8000 when in duty cycle mode)
-  The fan speed is regulated to keep the temp the fan is mapped to between
-  temp#_auto_point2_temp and temp#_auto_point3_temp.
-
-All of the automatic modes require that pwm1 corresponds to fan1, pwm2 to
-fan2 and pwm3 to fan3.