diff options
Diffstat (limited to 'Documentation/hwmon')
| -rw-r--r-- | Documentation/hwmon/adm1177.rst | 36 | ||||
| -rw-r--r-- | Documentation/hwmon/drivetemp.rst | 52 | ||||
| -rw-r--r-- | Documentation/hwmon/index.rst | 5 | ||||
| -rw-r--r-- | Documentation/hwmon/max20730.rst | 74 | ||||
| -rw-r--r-- | Documentation/hwmon/max31730.rst | 44 | ||||
| -rw-r--r-- | Documentation/hwmon/pmbus.rst | 10 | ||||
| -rw-r--r-- | Documentation/hwmon/ucd9000.rst | 12 | ||||
| -rw-r--r-- | Documentation/hwmon/xdpe12284.rst | 101 |
8 files changed, 332 insertions, 2 deletions
diff --git a/Documentation/hwmon/adm1177.rst b/Documentation/hwmon/adm1177.rst new file mode 100644 index 000000000000..c81e0b4abd28 --- /dev/null +++ b/Documentation/hwmon/adm1177.rst @@ -0,0 +1,36 @@ +Kernel driver adm1177 +===================== + +Supported chips: + * Analog Devices ADM1177 + Prefix: 'adm1177' + Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1177.pdf + +Author: Beniamin Bia <beniamin.bia@analog.com> + + +Description +----------- + +This driver supports hardware monitoring for Analog Devices ADM1177 +Hot-Swap Controller and Digital Power Monitors with Soft Start Pin. + + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + + +Sysfs entries +------------- + +The following attributes are supported. Current maxim attribute +is read-write, all other attributes are read-only. + +in0_input Measured voltage in microvolts. + +curr1_input Measured current in microamperes. +curr1_max_alarm Overcurrent alarm in microamperes. diff --git a/Documentation/hwmon/drivetemp.rst b/Documentation/hwmon/drivetemp.rst new file mode 100644 index 000000000000..2d37d049247f --- /dev/null +++ b/Documentation/hwmon/drivetemp.rst @@ -0,0 +1,52 @@ +.. SPDX-License-Identifier: GPL-2.0 + +Kernel driver drivetemp +======================= + + +References +---------- + +ANS T13/1699-D +Information technology - AT Attachment 8 - ATA/ATAPI Command Set (ATA8-ACS) + +ANS Project T10/BSR INCITS 513 +Information technology - SCSI Primary Commands - 4 (SPC-4) + +ANS Project INCITS 557 +Information technology - SCSI / ATA Translation - 5 (SAT-5) + + +Description +----------- + +This driver supports reporting the temperature of disk and solid state +drives with temperature sensors. + +If supported, it uses the ATA SCT Command Transport feature to read +the current drive temperature and, if available, temperature limits +as well as historic minimum and maximum temperatures. If SCT Command +Transport is not supported, the driver uses SMART attributes to read +the drive temperature. + + +Sysfs entries +------------- + +Only the temp1_input attribute is always available. Other attributes are +available only if reported by the drive. All temperatures are reported in +milli-degrees Celsius. + +======================= ===================================================== +temp1_input Current drive temperature +temp1_lcrit Minimum temperature limit. Operating the device below + this temperature may cause physical damage to the + device. +temp1_min Minimum recommended continuous operating limit +temp1_max Maximum recommended continuous operating temperature +temp1_crit Maximum temperature limit. Operating the device above + this temperature may cause physical damage to the + device. +temp1_lowest Minimum temperature seen this power cycle +temp1_highest Maximum temperature seen this power cycle +======================= ===================================================== diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst index 43cc605741ea..b24adb67ddca 100644 --- a/Documentation/hwmon/index.rst +++ b/Documentation/hwmon/index.rst @@ -29,6 +29,7 @@ Hardware Monitoring Kernel Drivers adm1025 adm1026 adm1031 + adm1177 adm1275 adm9240 ads7828 @@ -47,6 +48,7 @@ Hardware Monitoring Kernel Drivers da9055 dell-smm-hwmon dme1737 + drivetemp ds1621 ds620 emc1403 @@ -106,8 +108,10 @@ Hardware Monitoring Kernel Drivers max1619 max1668 max197 + max20730 max20751 max31722 + max31730 max31785 max31790 max34440 @@ -177,6 +181,7 @@ Hardware Monitoring Kernel Drivers wm831x wm8350 xgene-hwmon + xdpe12284 zl6100 .. only:: subproject and html diff --git a/Documentation/hwmon/max20730.rst b/Documentation/hwmon/max20730.rst new file mode 100644 index 000000000000..cea7ae58c2f7 --- /dev/null +++ b/Documentation/hwmon/max20730.rst @@ -0,0 +1,74 @@ +.. SPDX-License-Identifier: GPL-2.0-or-later + +Kernel driver max20730 +====================== + +Supported chips: + + * Maxim MAX20730 + + Prefix: 'max20730' + + Addresses scanned: - + + Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX20730.pdf + + * Maxim MAX20734 + + Prefix: 'max20734' + + Addresses scanned: - + + Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX20734.pdf + + * Maxim MAX20743 + + Prefix: 'max20743' + + Addresses scanned: - + + Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX20743.pdf + +Author: Guenter Roeck <linux@roeck-us.net> + + +Description +----------- + +This driver implements support for Maxim MAX20730, MAX20734, and MAX20743 +Integrated, Step-Down Switching Regulators with PMBus support. + +The driver is a client driver to the core PMBus driver. +Please see Documentation/hwmon/pmbus.rst for details on PMBus client drivers. + + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices.rst for +details. + + +Sysfs entries +------------- + +=================== ===== ======================================================= +curr1_crit RW/RO Critical output current. Please see datasheet for + supported limits. Read-only if the chip is + write protected; read-write otherwise. +curr1_crit_alarm RO Output current critical alarm +curr1_input RO Output current +curr1_label RO 'iout1' +in1_alarm RO Input voltage alarm +in1_input RO Input voltage +in1_label RO 'vin' +in2_alarm RO Output voltage alarm +in2_input RO Output voltage +in2_label RO 'vout1' +temp1_crit RW/RO Critical temeperature. Supported values are 130 or 150 + degrees C. Read-only if the chip is write protected; + read-write otherwise. +temp1_crit_alarm RO Temperature critical alarm +temp1_input RO Chip temperature +=================== ===== ======================================================= diff --git a/Documentation/hwmon/max31730.rst b/Documentation/hwmon/max31730.rst new file mode 100644 index 000000000000..def0de19dbd2 --- /dev/null +++ b/Documentation/hwmon/max31730.rst @@ -0,0 +1,44 @@ +Kernel driver max31790 +====================== + +Supported chips: + + * Maxim MAX31730 + + Prefix: 'max31730' + + Addresses scanned: 0x1c, 0x1d, 0x1e, 0x1f, 0x4c, 0x4d, 0x4e, 0x4f + + Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX31730.pdf + +Author: Guenter Roeck <linux@roeck-us.net> + + +Description +----------- + +This driver implements support for Maxim MAX31730. + +The MAX31730 temperature sensor monitors its own temperature and the +temperatures of three external diode-connected transistors. The operating +supply voltage is from 3.0V to 3.6V. Resistance cancellation compensates +for high series resistance in circuit-board traces and the external thermal +diode, while beta compensation corrects for temperature-measurement +errors due to low-beta sensing transistors. + + +Sysfs entries +------------- + +=================== == ======================================================= +temp[1-4]_enable RW Temperature enable/disable + Set to 0 to enable channel, 0 to disable +temp[1-4]_input RO Temperature input +temp[2-4]_fault RO Fault indicator for remote channels +temp[1-4]_max RW Maximum temperature +temp[1-4]_max_alarm RW Maximum temperature alarm +temp[1-4]_min RW Minimum temperature. Common for all channels. + Only temp1_min is writeable. +temp[1-4]_min_alarm RO Minimum temperature alarm +temp[2-4]_offset RW Temperature offset for remote channels +=================== == ======================================================= diff --git a/Documentation/hwmon/pmbus.rst b/Documentation/hwmon/pmbus.rst index abfb9dd4857d..f787984e88a9 100644 --- a/Documentation/hwmon/pmbus.rst +++ b/Documentation/hwmon/pmbus.rst @@ -63,6 +63,16 @@ Supported chips: http://www.ti.com/lit/gpn/tps544c25 + * Maxim MAX20796 + + Prefix: 'max20796' + + Addresses scanned: - + + Datasheet: + + Not published + * Generic PMBus devices Prefix: 'pmbus' diff --git a/Documentation/hwmon/ucd9000.rst b/Documentation/hwmon/ucd9000.rst index 746f21fcb48c..704f0cbd95d3 100644 --- a/Documentation/hwmon/ucd9000.rst +++ b/Documentation/hwmon/ucd9000.rst @@ -3,9 +3,10 @@ Kernel driver ucd9000 Supported chips: - * TI UCD90120, UCD90124, UCD90160, UCD9090, and UCD90910 + * TI UCD90120, UCD90124, UCD90160, UCD90320, UCD9090, and UCD90910 - Prefixes: 'ucd90120', 'ucd90124', 'ucd90160', 'ucd9090', 'ucd90910' + Prefixes: 'ucd90120', 'ucd90124', 'ucd90160', 'ucd90320', 'ucd9090', + 'ucd90910' Addresses scanned: - @@ -14,6 +15,7 @@ Supported chips: - http://focus.ti.com/lit/ds/symlink/ucd90120.pdf - http://focus.ti.com/lit/ds/symlink/ucd90124.pdf - http://focus.ti.com/lit/ds/symlink/ucd90160.pdf + - http://focus.ti.com/lit/ds/symlink/ucd90320.pdf - http://focus.ti.com/lit/ds/symlink/ucd9090.pdf - http://focus.ti.com/lit/ds/symlink/ucd90910.pdf @@ -45,6 +47,12 @@ power-on reset signals, external interrupts, cascading, or other system functions. Twelve of these pins offer PWM functionality. Using these pins, the UCD90160 offers support for margining, and general-purpose PWM functions. +The UCD90320 is a 32-rail PMBus/I2C addressable power-supply sequencer and +monitor. The 24 integrated ADC channels (AMONx) monitor the power supply +voltage, current, and temperature. Of the 84 GPIO pins, 8 can be used as +digital monitors (DMONx), 32 to enable the power supply (ENx), 24 for margining +(MARx), 16 for logical GPO, and 32 GPIs for cascading, and system function. + The UCD9090 is a 10-rail PMBus/I2C addressable power-supply sequencer and monitor. The device integrates a 12-bit ADC for monitoring up to 10 power-supply voltage inputs. Twenty-three GPIO pins can be used for power supply enables, diff --git a/Documentation/hwmon/xdpe12284.rst b/Documentation/hwmon/xdpe12284.rst new file mode 100644 index 000000000000..6b7ae98cc536 --- /dev/null +++ b/Documentation/hwmon/xdpe12284.rst @@ -0,0 +1,101 @@ +.. SPDX-License-Identifier: GPL-2.0 + +Kernel driver xdpe122 +===================== + +Supported chips: + + * Infineon XDPE12254 + + Prefix: 'xdpe12254' + + * Infineon XDPE12284 + + Prefix: 'xdpe12284' + +Authors: + + Vadim Pasternak <vadimp@mellanox.com> + +Description +----------- + +This driver implements support for Infineon Multi-phase XDPE122 family +dual loop voltage regulators. +The family includes XDPE12284 and XDPE12254 devices. +The devices from this family complaint with: +- Intel VR13 and VR13HC rev 1.3, IMVP8 rev 1.2 and IMPVP9 rev 1.3 DC-DC + converter specification. +- Intel SVID rev 1.9. protocol. +- PMBus rev 1.3 interface. + +Devices support linear format for reading input voltage, input and output current, +input and output power and temperature. +Device supports VID format for reading output voltage. The below modes are +supported: +- VR12.0 mode, 5-mV DAC - 0x01. +- VR12.5 mode, 10-mV DAC - 0x02. +- IMVP9 mode, 5-mV DAC - 0x03. +- AMD mode 6.25mV - 0x10. + +Devices support two pages for telemetry. + +The driver provides for current: input, maximum and critical thresholds +and maximum and critical alarms. Critical thresholds and critical alarm are +supported only for current output. +The driver exports the following attributes for via the sysfs files, where +indexes 1, 2 are for "iin" and 3, 4 for "iout": + +**curr[3-4]_crit** + +**curr[3-4]_crit_alarm** + +**curr[1-4]_input** + +**curr[1-4]_label** + +**curr[1-4]_max** + +**curr[1-4]_max_alarm** + +The driver provides for voltage: input, critical and low critical thresholds +and critical and low critical alarms. +The driver exports the following attributes for via the sysfs files, where +indexes 1, 2 are for "vin" and 3, 4 for "vout": + +**in[1-4]_crit** + +**in[1-4_crit_alarm** + +**in[1-4]_input** + +**in[1-4_label** + +**in[1-4]_lcrit** + +**in[1-41_lcrit_alarm** + +The driver provides for power: input and alarms. Power alarm is supported only +for power input. +The driver exports the following attributes for via the sysfs files, where +indexes 1, 2 are for "pin" and 3, 4 for "pout": + +**power[1-2]_alarm** + +**power[1-4]_input** + +**power[1-4]_label** + +The driver provides for temperature: input, maximum and critical thresholds +and maximum and critical alarms. +The driver exports the following attributes for via the sysfs files: + +**temp[1-2]_crit** + +**temp[1-2]_crit_alarm** + +**temp[1-2]_input** + +**temp[1-2]_max** + +**temp[1-2]_max_alarm** |