diff options
Diffstat (limited to 'Documentation/isdn/README.act2000')
| -rw-r--r-- | Documentation/isdn/README.act2000 | 104 |
1 files changed, 0 insertions, 104 deletions
diff --git a/Documentation/isdn/README.act2000 b/Documentation/isdn/README.act2000 deleted file mode 100644 index ce7115e7f4ce..000000000000 --- a/Documentation/isdn/README.act2000 +++ /dev/null @@ -1,104 +0,0 @@ -$Id: README.act2000,v 1.3 2000/08/06 09:22:51 armin Exp $ - -This document describes the ACT2000 driver for the -IBM Active 2000 ISDN card. - -There are 3 Types of this card available. A ISA-, MCA-, and PCMCIA-Bus -Version. Currently, only the ISA-Bus version of the card is supported. -However MCA and PCMCIA will follow soon. - -The ISA-Bus Version uses 8 IO-ports. The base port address has to be set -manually using the DIP switches. - -Setting up the DIP switches for the IBM Active 2000 ISDN card: - - Note: S5 and S6 always set off! - - S1 S2 S3 S4 Base-port - on on on on 0x0200 (Factory default) - off on on on 0x0240 - on off on on 0x0280 - off off on on 0x02c0 - on on off on 0x0300 - off on off on 0x0340 - on off off on 0x0380 - on on on off 0xcfe0 - off on on off 0xcfa0 - on off on off 0xcf60 - off off on off 0xcf20 - on on off off 0xcee0 - off on off off 0xcea0 - on off off off 0xce60 - off off off off Card disabled - -IRQ is configured by software. Possible values are: - - 3, 5, 7, 10, 11, 12, 15 and none (polled mode) - - -The ACT2000 driver may either be built into the kernel or as a module. -Initialization depends on how the driver is built: - -Driver built into the kernel: - - The ACT2000 driver can be configured using the commandline-feature while - loading the kernel with LILO or LOADLIN. It accepts the following syntax: - - act2000=b,p,i[,idstring] - - where - - b = Bus-Type (1=ISA, 2=MCA, 3=PCMCIA) - p = portbase (-1 means autoprobe) - i = Interrupt (-1 means use next free IRQ, 0 means polled mode) - - The idstring is an arbitrary string used for referencing the card - by the actctrl tool later. - - Defaults used, when no parameters given at all: - - 1,-1,-1,"" - - which means: Autoprobe for an ISA card, use next free IRQ, let the - ISDN linklevel fill the IdString (usually "line0" for the first card). - - If you like to use more than one card, you can use the program - "actctrl" from the utility-package to configure additional cards. - - Using the "actctrl"-utility, portbase and irq can also be changed - during runtime. The D-channel protocol is configured by the "dproto" - option of the "actctrl"-utility after loading the firmware into the - card's memory using the "actctrl"-utility. - -Driver built as module: - - The module act2000.o can be configured during modprobe (insmod) by - appending its parameters to the modprobe resp. insmod commandline. - The following syntax is accepted: - - act_bus=b act_port=p act_irq=i act_id=idstring - - where b, p, i and idstring have the same meanings as the parameters - described for the builtin version above. - - Using the "actctrl"-utility, the same features apply to the modularized - version as to the kernel-builtin one. (i.e. loading of firmware and - configuring the D-channel protocol) - -Loading the firmware into the card: - - The firmware is supplied together with the isdn4k-utils package. It - can be found in the subdirectory act2000/firmware/ - - Assuming you have installed the utility-package correctly, the firmware - will be downloaded into the card using the following command: - - actctrl -d idstring load /etc/isdn/bip11.btl - - where idstring is the Name of the card, given during insmod-time or - (for kernel-builtin driver) on the kernel commandline. If only one - ISDN card is used, the -d isdstrin may be omitted. - - For further documentation (adding more IBM Active 2000 cards), refer to - the manpage actctrl.8 which is included in the isdn4k-utils package. - |