diff options
Diffstat (limited to 'Documentation/networking')
| -rw-r--r-- | Documentation/networking/devlink/devlink-params.rst | 90 | ||||
| -rw-r--r-- | Documentation/networking/devlink/devlink-params.txt | 71 | ||||
| -rw-r--r-- | Documentation/networking/devlink/index.rst | 1 |
3 files changed, 91 insertions, 71 deletions
diff --git a/Documentation/networking/devlink/devlink-params.rst b/Documentation/networking/devlink/devlink-params.rst new file mode 100644 index 000000000000..b51b91f807f7 --- /dev/null +++ b/Documentation/networking/devlink/devlink-params.rst @@ -0,0 +1,90 @@ +.. SPDX-License-Identifier: GPL-2.0 + +============== +Devlink Params +============== + +``devlink`` provides capability for a driver to expose device parameters for low +level device functionality. Since devlink can operate at the device-wide +level, it can be used to provide configuration that may affect multiple +ports on a single device. + +This document describes a number of generic parameters that are supported +across multiple drivers. Each driver is also free to add their own +parameters. Each driver must document the specific parameters they support, +whether generic or not. + +Configuration modes +=================== + +Parameters may be set in different configuration modes. + +.. list-table:: Possible configuration modes + :widths: 5 90 + + * - Name + - Description + * - ``runtime`` + - set while the driver is running, and takes effect immediately. No + reset is required. + * - ``driverinit`` + - applied while the driver initializes. Requires the user to restart + the driver using the ``devlink`` reload command. + * - ``permanent`` + - written to the device's non-volatile memory. A hard reset is required + for it to take effect. + +Generic configuration parameters +================================ +The following is a list of generic configuration parameters that drivers may +add. Use of generic parameters is preferred over each driver creating their +own name. + +.. list-table:: List of generic parameters + :widths: 5 5 90 + + * - Name + - Type + - Description + * - ``enable_sriov`` + - Boolean + - Enable Single Root I/O Virtualization (SRIOV) in the device. + * - ``ignore_ari`` + - Boolean + - Ignore Alternative Routing-ID Interpretation (ARI) capability. If + enabled, the adapter will ignore ARI capability even when the + platform has support enabled. The device will create the same number + of partitions as when the platform does not support ARI. + * - ``msix_vec_per_pf_max`` + - u32 + - Provides the maximum number of MSI-X interrupts that a device can + create. Value is the same across all physical functions (PFs) in the + device. + * - ``msix_vec_per_pf_min`` + - u32 + - Provides the minimum number of MSI-X interrupts required for the + device to initialize. Value is the same across all physical functions + (PFs) in the device. + * - ``fw_load_policy`` + - u8 + - Control the device's firmware loading policy. + - ``DEVLINK_PARAM_FW_LOAD_POLICY_VALUE_DRIVER`` (0) + Load firmware version preferred by the driver. + - ``DEVLINK_PARAM_FW_LOAD_POLICY_VALUE_FLASH`` (1) + Load firmware currently stored in flash. + - ``DEVLINK_PARAM_FW_LOAD_POLICY_VALUE_DISK`` (2) + Load firmware currently available on host's disk. + * - ``reset_dev_on_drv_probe`` + - u8 + - Controls the device's reset policy on driver probe. + - ``DEVLINK_PARAM_RESET_DEV_ON_DRV_PROBE_VALUE_UNKNOWN`` (0) + Unknown or invalid value. + - ``DEVLINK_PARAM_RESET_DEV_ON_DRV_PROBE_VALUE_ALWAYS`` (1) + Always reset device on driver probe. + - ``DEVLINK_PARAM_RESET_DEV_ON_DRV_PROBE_VALUE_NEVER`` (2) + Never reset device on driver probe. + - ``DEVLINK_PARAM_RESET_DEV_ON_DRV_PROBE_VALUE_DISK`` (3) + Reset the device only if firmware can be found in the filesystem. + * - ``enable_roce`` + - Boolean + - Enable handling of RoCE traffic in the device. diff --git a/Documentation/networking/devlink/devlink-params.txt b/Documentation/networking/devlink/devlink-params.txt deleted file mode 100644 index 04e234e9acc9..000000000000 --- a/Documentation/networking/devlink/devlink-params.txt +++ /dev/null @@ -1,71 +0,0 @@ -Devlink configuration parameters -================================ -Following is the list of configuration parameters via devlink interface. -Each parameter can be generic or driver specific and are device level -parameters. - -Note that the driver-specific files should contain the generic params -they support to, with supported config modes. - -Each parameter can be set in different configuration modes: - runtime - set while driver is running, no reset required. - driverinit - applied while driver initializes, requires restart - driver by devlink reload command. - permanent - written to device's non-volatile memory, hard reset - required. - -Following is the list of parameters: -==================================== -enable_sriov [DEVICE, GENERIC] - Enable Single Root I/O Virtualisation (SRIOV) in - the device. - Type: Boolean - -ignore_ari [DEVICE, GENERIC] - Ignore Alternative Routing-ID Interpretation (ARI) - capability. If enabled, adapter will ignore ARI - capability even when platforms has the support - enabled and creates same number of partitions when - platform does not support ARI. - Type: Boolean - -msix_vec_per_pf_max [DEVICE, GENERIC] - Provides the maximum number of MSIX interrupts that - a device can create. Value is same across all - physical functions (PFs) in the device. - Type: u32 - -msix_vec_per_pf_min [DEVICE, GENERIC] - Provides the minimum number of MSIX interrupts required - for the device initialization. Value is same across all - physical functions (PFs) in the device. - Type: u32 - -fw_load_policy [DEVICE, GENERIC] - Controls the device's firmware loading policy. - Valid values: - * DEVLINK_PARAM_FW_LOAD_POLICY_VALUE_DRIVER (0) - Load firmware version preferred by the driver. - * DEVLINK_PARAM_FW_LOAD_POLICY_VALUE_FLASH (1) - Load firmware currently stored in flash. - * DEVLINK_PARAM_FW_LOAD_POLICY_VALUE_DISK (2) - Load firmware currently available on host's disk. - Type: u8 - -reset_dev_on_drv_probe [DEVICE, GENERIC] - Controls the device's reset policy on driver probe. - Valid values: - * DEVLINK_PARAM_RESET_DEV_ON_DRV_PROBE_VALUE_UNKNOWN (0) - Unknown or invalid value. - * DEVLINK_PARAM_RESET_DEV_ON_DRV_PROBE_VALUE_ALWAYS (1) - Always reset device on driver probe. - * DEVLINK_PARAM_RESET_DEV_ON_DRV_PROBE_VALUE_NEVER (2) - Never reset device on driver probe. - * DEVLINK_PARAM_RESET_DEV_ON_DRV_PROBE_VALUE_DISK (3) - Reset only if device firmware can be found in the - filesystem. - Type: u8 - -enable_roce [DEVICE, GENERIC] - Enable handling of RoCE traffic in the device. - Type: Boolean diff --git a/Documentation/networking/devlink/index.rst b/Documentation/networking/devlink/index.rst index 687bb6e51fca..ae3f20919d22 100644 --- a/Documentation/networking/devlink/index.rst +++ b/Documentation/networking/devlink/index.rst @@ -11,5 +11,6 @@ Contents: devlink-health devlink-info + devlink-params devlink-trap devlink-trap-netdevsim |