diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/power/devices.txt | 110 |
1 files changed, 76 insertions, 34 deletions
diff --git a/Documentation/power/devices.txt b/Documentation/power/devices.txt index 57080cd74575..88880839ece4 100644 --- a/Documentation/power/devices.txt +++ b/Documentation/power/devices.txt @@ -1,6 +1,6 @@ Device Power Management -Copyright (c) 2010 Rafael J. Wysocki <rjw@sisk.pl>, Novell Inc. +Copyright (c) 2010-2011 Rafael J. Wysocki <rjw@sisk.pl>, Novell Inc. Copyright (c) 2010 Alan Stern <stern@rowland.harvard.edu> @@ -159,18 +159,18 @@ matter, and the kernel is responsible for keeping track of it. By contrast, whether or not a wakeup-capable device should issue wakeup events is a policy decision, and it is managed by user space through a sysfs attribute: the power/wakeup file. User space can write the strings "enabled" or "disabled" to -set or clear the should_wakeup flag, respectively. Reads from the file will -return the corresponding string if can_wakeup is true, but if can_wakeup is -false then reads will return an empty string, to indicate that the device -doesn't support wakeup events. (But even though the file appears empty, writes -will still affect the should_wakeup flag.) +set or clear the "should_wakeup" flag, respectively. This file is only present +for wakeup-capable devices (i.e. devices whose "can_wakeup" flags are set) +and is created (or removed) by device_set_wakeup_capable(). Reads from the +file will return the corresponding string. The device_may_wakeup() routine returns true only if both flags are set. -Drivers should check this routine when putting devices in a low-power state -during a system sleep transition, to see whether or not to enable the devices' -wakeup mechanisms. However for runtime power management, wakeup events should -be enabled whenever the device and driver both support them, regardless of the -should_wakeup flag. +This information is used by subsystems, like the PCI bus type code, to see +whether or not to enable the devices' wakeup mechanisms. If device wakeup +mechanisms are enabled or disabled directly by drivers, they also should use +device_may_wakeup() to decide what to do during a system sleep transition. +However for runtime power management, wakeup events should be enabled whenever +the device and driver both support them, regardless of the should_wakeup flag. /sys/devices/.../power/control files @@ -249,23 +249,18 @@ various phases always run after tasks have been frozen and before they are unfrozen. Furthermore, the *_noirq phases run at a time when IRQ handlers have been disabled (except for those marked with the IRQ_WAKEUP flag). -Most phases use bus, type, and class callbacks (that is, methods defined in -dev->bus->pm, dev->type->pm, and dev->class->pm). The prepare and complete -phases are exceptions; they use only bus callbacks. When multiple callbacks -are used in a phase, they are invoked in the order: <class, type, bus> during -power-down transitions and in the opposite order during power-up transitions. -For example, during the suspend phase the PM core invokes - - dev->class->pm.suspend(dev); - dev->type->pm.suspend(dev); - dev->bus->pm.suspend(dev); - -before moving on to the next device, whereas during the resume phase the core -invokes - - dev->bus->pm.resume(dev); - dev->type->pm.resume(dev); - dev->class->pm.resume(dev); +All phases use bus, type, or class callbacks (that is, methods defined in +dev->bus->pm, dev->type->pm, or dev->class->pm). These callbacks are mutually +exclusive, so if the device type provides a struct dev_pm_ops object pointed to +by its pm field (i.e. both dev->type and dev->type->pm are defined), the +callbacks included in that object (i.e. dev->type->pm) will be used. Otherwise, +if the class provides a struct dev_pm_ops object pointed to by its pm field +(i.e. both dev->class and dev->class->pm are defined), the PM core will use the +callbacks from that object (i.e. dev->class->pm). Finally, if the pm fields of +both the device type and class objects are NULL (or those objects do not exist), +the callbacks provided by the bus (that is, the callbacks from dev->bus->pm) +will be used (this allows device types to override callbacks provided by bus +types or classes if necessary). These callbacks may in turn invoke device- or driver-specific methods stored in dev->driver->pm, but they don't have to. @@ -284,11 +279,15 @@ When the system goes into the standby or memory sleep state, the phases are: time.) Unlike the other suspend-related phases, during the prepare phase the device tree is traversed top-down. - The prepare phase uses only a bus callback. After the callback method - returns, no new children may be registered below the device. The method - may also prepare the device or driver in some way for the upcoming - system power transition, but it should not put the device into a - low-power state. + In addition to that, if device drivers need to allocate additional + memory to be able to hadle device suspend correctly, that should be + done in the prepare phase. + + After the prepare callback method returns, no new children may be + registered below the device. The method may also prepare the device or + driver in some way for the upcoming system power transition (for + example, by allocating additional memory required for this purpose), but + it should not put the device into a low-power state. 2. The suspend methods should quiesce the device to stop it from performing I/O. They also may save the device registers and put it into the @@ -372,7 +371,7 @@ Drivers need to be able to handle hardware which has been reset since the suspend methods were called, for example by complete reinitialization. This may be the hardest part, and the one most protected by NDA'd documents and chip errata. It's simplest if the hardware state hasn't changed since -the suspend was carried out, but that can't be guaranteed (in fact, it ususally +the suspend was carried out, but that can't be guaranteed (in fact, it usually is not the case). Drivers must also be prepared to notice that the device has been removed @@ -507,6 +506,49 @@ routines. Nevertheless, different callback pointers are used in case there is a situation where it actually matters. +Device Power Domains +-------------------- +Sometimes devices share reference clocks or other power resources. In those +cases it generally is not possible to put devices into low-power states +individually. Instead, a set of devices sharing a power resource can be put +into a low-power state together at the same time by turning off the shared +power resource. Of course, they also need to be put into the full-power state +together, by turning the shared power resource on. A set of devices with this +property is often referred to as a power domain. + +Support for power domains is provided through the pwr_domain field of struct +device. This field is a pointer to an object of type struct dev_power_domain, +defined in include/linux/pm.h, providing a set of power management callbacks +analogous to the subsystem-level and device driver callbacks that are executed +for the given device during all power transitions, in addition to the respective +subsystem-level callbacks. Specifically, the power domain "suspend" callbacks +(i.e. ->runtime_suspend(), ->suspend(), ->freeze(), ->poweroff(), etc.) are +executed after the analogous subsystem-level callbacks, while the power domain +"resume" callbacks (i.e. ->runtime_resume(), ->resume(), ->thaw(), ->restore, +etc.) are executed before the analogous subsystem-level callbacks. Error codes +returned by the "suspend" and "resume" power domain callbacks are ignored. + +Power domain ->runtime_idle() callback is executed before the subsystem-level +->runtime_idle() callback and the result returned by it is not ignored. Namely, +if it returns error code, the subsystem-level ->runtime_idle() callback will not +be called and the helper function rpm_idle() executing it will return error +code. This mechanism is intended to help platforms where saving device state +is a time consuming operation and should only be carried out if all devices +in the power domain are idle, before turning off the shared power resource(s). +Namely, the power domain ->runtime_idle() callback may return error code until +the pm_runtime_idle() helper (or its asychronous version) has been called for +all devices in the power domain (it is recommended that the returned error code +be -EBUSY in those cases), preventing the subsystem-level ->runtime_idle() +callback from being run prematurely. + +The support for device power domains is only relevant to platforms needing to +use the same subsystem-level (e.g. platform bus type) and device driver power +management callbacks in many different power domain configurations and wanting +to avoid incorporating the support for power domains into the subsystem-level +callbacks. The other platforms need not implement it or take it into account +in any way. + + System Devices -------------- System devices (sysdevs) follow a slightly different API, which can be found in |