diff options
Diffstat (limited to 'Documentation/powerpc/dts-bindings/fsl')
| -rw-r--r-- | Documentation/powerpc/dts-bindings/fsl/i2c.txt | 46 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/fsl/upm-nand.txt | 39 |
2 files changed, 68 insertions, 17 deletions
diff --git a/Documentation/powerpc/dts-bindings/fsl/i2c.txt b/Documentation/powerpc/dts-bindings/fsl/i2c.txt index d0ab33e21fe6..b6d2e21474f9 100644 --- a/Documentation/powerpc/dts-bindings/fsl/i2c.txt +++ b/Documentation/powerpc/dts-bindings/fsl/i2c.txt @@ -7,8 +7,10 @@ Required properties : Recommended properties : - - compatible : Should be "fsl-i2c" for parts compatible with - Freescale I2C specifications. + - compatible : compatibility list with 2 entries, the first should + be "fsl,CHIP-i2c" where CHIP is the name of a compatible processor, + e.g. mpc8313, mpc8543, mpc8544, mpc5200 or mpc5200b. The second one + should be "fsl-i2c". - interrupts : <a b> where a is the interrupt number and b is a field that represents an encoding of the sense and level information for the interrupt. This should be encoded based on @@ -16,17 +18,31 @@ Recommended properties : controller you have. - interrupt-parent : the phandle for the interrupt controller that services interrupts for this device. - - dfsrr : boolean; if defined, indicates that this I2C device has - a digital filter sampling rate register - - fsl5200-clocking : boolean; if defined, indicated that this device - uses the FSL 5200 clocking mechanism. - -Example : - i2c@3000 { - interrupt-parent = <40000>; - interrupts = <1b 3>; - reg = <3000 18>; - device_type = "i2c"; - compatible = "fsl-i2c"; - dfsrr; + - fsl,preserve-clocking : boolean; if defined, the clock settings + from the bootloader are preserved (not touched). + - clock-frequency : desired I2C bus clock frequency in Hz. + +Examples : + + i2c@3d00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; + cell-index = <0>; + reg = <0x3d00 0x40>; + interrupts = <2 15 0>; + interrupt-parent = <&mpc5200_pic>; + fsl,preserve-clocking; }; + + i2c@3100 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <1>; + compatible = "fsl,mpc8544-i2c", "fsl-i2c"; + reg = <0x3100 0x100>; + interrupts = <43 2>; + interrupt-parent = <&mpic>; + clock-frequency = <400000>; + }; + diff --git a/Documentation/powerpc/dts-bindings/fsl/upm-nand.txt b/Documentation/powerpc/dts-bindings/fsl/upm-nand.txt index 84a04d5eb8e6..a48b2cadc7f0 100644 --- a/Documentation/powerpc/dts-bindings/fsl/upm-nand.txt +++ b/Documentation/powerpc/dts-bindings/fsl/upm-nand.txt @@ -5,9 +5,21 @@ Required properties: - reg : should specify localbus chip select and size used for the chip. - fsl,upm-addr-offset : UPM pattern offset for the address latch. - fsl,upm-cmd-offset : UPM pattern offset for the command latch. -- gpios : may specify optional GPIO connected to the Ready-Not-Busy pin. -Example: +Optional properties: +- fsl,upm-wait-flags : add chip-dependent short delays after running the + UPM pattern (0x1), after writing a data byte (0x2) or after + writing out a buffer (0x4). +- fsl,upm-addr-line-cs-offsets : address offsets for multi-chip support. + The corresponding address lines are used to select the chip. +- gpios : may specify optional GPIOs connected to the Ready-Not-Busy pins + (R/B#). For multi-chip devices, "n" GPIO definitions are required + according to the number of chips. +- chip-delay : chip dependent delay for transfering data from array to + read registers (tR). Required if property "gpios" is not used + (R/B# pins not connected). + +Examples: upm@1,0 { compatible = "fsl,upm-nand"; @@ -26,3 +38,26 @@ upm@1,0 { }; }; }; + +upm@3,0 { + #address-cells = <0>; + #size-cells = <0>; + compatible = "tqc,tqm8548-upm-nand", "fsl,upm-nand"; + reg = <3 0x0 0x800>; + fsl,upm-addr-offset = <0x10>; + fsl,upm-cmd-offset = <0x08>; + /* Multi-chip NAND device */ + fsl,upm-addr-line-cs-offsets = <0x0 0x200>; + fsl,upm-wait-flags = <0x5>; + chip-delay = <25>; // in micro-seconds + + nand@0 { + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "fs"; + reg = <0x00000000 0x10000000>; + }; + }; +}; |