diff options
Diffstat (limited to 'Documentation/powerpc/eeh-pci-error-recovery.txt')
| -rw-r--r-- | Documentation/powerpc/eeh-pci-error-recovery.txt | 334 |
1 files changed, 0 insertions, 334 deletions
diff --git a/Documentation/powerpc/eeh-pci-error-recovery.txt b/Documentation/powerpc/eeh-pci-error-recovery.txt deleted file mode 100644 index 678189280bb4..000000000000 --- a/Documentation/powerpc/eeh-pci-error-recovery.txt +++ /dev/null @@ -1,334 +0,0 @@ - - - PCI Bus EEH Error Recovery - -------------------------- - Linas Vepstas - <linas@austin.ibm.com> - 12 January 2005 - - -Overview: ---------- -The IBM POWER-based pSeries and iSeries computers include PCI bus -controller chips that have extended capabilities for detecting and -reporting a large variety of PCI bus error conditions. These features -go under the name of "EEH", for "Enhanced Error Handling". The EEH -hardware features allow PCI bus errors to be cleared and a PCI -card to be "rebooted", without also having to reboot the operating -system. - -This is in contrast to traditional PCI error handling, where the -PCI chip is wired directly to the CPU, and an error would cause -a CPU machine-check/check-stop condition, halting the CPU entirely. -Another "traditional" technique is to ignore such errors, which -can lead to data corruption, both of user data or of kernel data, -hung/unresponsive adapters, or system crashes/lockups. Thus, -the idea behind EEH is that the operating system can become more -reliable and robust by protecting it from PCI errors, and giving -the OS the ability to "reboot"/recover individual PCI devices. - -Future systems from other vendors, based on the PCI-E specification, -may contain similar features. - - -Causes of EEH Errors --------------------- -EEH was originally designed to guard against hardware failure, such -as PCI cards dying from heat, humidity, dust, vibration and bad -electrical connections. The vast majority of EEH errors seen in -"real life" are due to either poorly seated PCI cards, or, -unfortunately quite commonly, due to device driver bugs, device firmware -bugs, and sometimes PCI card hardware bugs. - -The most common software bug, is one that causes the device to -attempt to DMA to a location in system memory that has not been -reserved for DMA access for that card. This is a powerful feature, -as it prevents what; otherwise, would have been silent memory -corruption caused by the bad DMA. A number of device driver -bugs have been found and fixed in this way over the past few -years. Other possible causes of EEH errors include data or -address line parity errors (for example, due to poor electrical -connectivity due to a poorly seated card), and PCI-X split-completion -errors (due to software, device firmware, or device PCI hardware bugs). -The vast majority of "true hardware failures" can be cured by -physically removing and re-seating the PCI card. - - -Detection and Recovery ----------------------- -In the following discussion, a generic overview of how to detect -and recover from EEH errors will be presented. This is followed -by an overview of how the current implementation in the Linux -kernel does it. The actual implementation is subject to change, -and some of the finer points are still being debated. These -may in turn be swayed if or when other architectures implement -similar functionality. - -When a PCI Host Bridge (PHB, the bus controller connecting the -PCI bus to the system CPU electronics complex) detects a PCI error -condition, it will "isolate" the affected PCI card. Isolation -will block all writes (either to the card from the system, or -from the card to the system), and it will cause all reads to -return all-ff's (0xff, 0xffff, 0xffffffff for 8/16/32-bit reads). -This value was chosen because it is the same value you would -get if the device was physically unplugged from the slot. -This includes access to PCI memory, I/O space, and PCI config -space. Interrupts; however, will continued to be delivered. - -Detection and recovery are performed with the aid of ppc64 -firmware. The programming interfaces in the Linux kernel -into the firmware are referred to as RTAS (Run-Time Abstraction -Services). The Linux kernel does not (should not) access -the EEH function in the PCI chipsets directly, primarily because -there are a number of different chipsets out there, each with -different interfaces and quirks. The firmware provides a -uniform abstraction layer that will work with all pSeries -and iSeries hardware (and be forwards-compatible). - -If the OS or device driver suspects that a PCI slot has been -EEH-isolated, there is a firmware call it can make to determine if -this is the case. If so, then the device driver should put itself -into a consistent state (given that it won't be able to complete any -pending work) and start recovery of the card. Recovery normally -would consist of resetting the PCI device (holding the PCI #RST -line high for two seconds), followed by setting up the device -config space (the base address registers (BAR's), latency timer, -cache line size, interrupt line, and so on). This is followed by a -reinitialization of the device driver. In a worst-case scenario, -the power to the card can be toggled, at least on hot-plug-capable -slots. In principle, layers far above the device driver probably -do not need to know that the PCI card has been "rebooted" in this -way; ideally, there should be at most a pause in Ethernet/disk/USB -I/O while the card is being reset. - -If the card cannot be recovered after three or four resets, the -kernel/device driver should assume the worst-case scenario, that the -card has died completely, and report this error to the sysadmin. -In addition, error messages are reported through RTAS and also through -syslogd (/var/log/messages) to alert the sysadmin of PCI resets. -The correct way to deal with failed adapters is to use the standard -PCI hotplug tools to remove and replace the dead card. - - -Current PPC64 Linux EEH Implementation --------------------------------------- -At this time, a generic EEH recovery mechanism has been implemented, -so that individual device drivers do not need to be modified to support -EEH recovery. This generic mechanism piggy-backs on the PCI hotplug -infrastructure, and percolates events up through the userspace/udev -infrastructure. Following is a detailed description of how this is -accomplished. - -EEH must be enabled in the PHB's very early during the boot process, -and if a PCI slot is hot-plugged. The former is performed by -eeh_init() in arch/powerpc/platforms/pseries/eeh.c, and the later by -drivers/pci/hotplug/pSeries_pci.c calling in to the eeh.c code. -EEH must be enabled before a PCI scan of the device can proceed. -Current Power5 hardware will not work unless EEH is enabled; -although older Power4 can run with it disabled. Effectively, -EEH can no longer be turned off. PCI devices *must* be -registered with the EEH code; the EEH code needs to know about -the I/O address ranges of the PCI device in order to detect an -error. Given an arbitrary address, the routine -pci_get_device_by_addr() will find the pci device associated -with that address (if any). - -The default arch/powerpc/include/asm/io.h macros readb(), inb(), insb(), -etc. include a check to see if the i/o read returned all-0xff's. -If so, these make a call to eeh_dn_check_failure(), which in turn -asks the firmware if the all-ff's value is the sign of a true EEH -error. If it is not, processing continues as normal. The grand -total number of these false alarms or "false positives" can be -seen in /proc/ppc64/eeh (subject to change). Normally, almost -all of these occur during boot, when the PCI bus is scanned, where -a large number of 0xff reads are part of the bus scan procedure. - -If a frozen slot is detected, code in -arch/powerpc/platforms/pseries/eeh.c will print a stack trace to -syslog (/var/log/messages). This stack trace has proven to be very -useful to device-driver authors for finding out at what point the EEH -error was detected, as the error itself usually occurs slightly -beforehand. - -Next, it uses the Linux kernel notifier chain/work queue mechanism to -allow any interested parties to find out about the failure. Device -drivers, or other parts of the kernel, can use -eeh_register_notifier(struct notifier_block *) to find out about EEH -events. The event will include a pointer to the pci device, the -device node and some state info. Receivers of the event can "do as -they wish"; the default handler will be described further in this -section. - -To assist in the recovery of the device, eeh.c exports the -following functions: - -rtas_set_slot_reset() -- assert the PCI #RST line for 1/8th of a second -rtas_configure_bridge() -- ask firmware to configure any PCI bridges - located topologically under the pci slot. -eeh_save_bars() and eeh_restore_bars(): save and restore the PCI - config-space info for a device and any devices under it. - - -A handler for the EEH notifier_block events is implemented in -drivers/pci/hotplug/pSeries_pci.c, called handle_eeh_events(). -It saves the device BAR's and then calls rpaphp_unconfig_pci_adapter(). -This last call causes the device driver for the card to be stopped, -which causes uevents to go out to user space. This triggers -user-space scripts that might issue commands such as "ifdown eth0" -for ethernet cards, and so on. This handler then sleeps for 5 seconds, -hoping to give the user-space scripts enough time to complete. -It then resets the PCI card, reconfigures the device BAR's, and -any bridges underneath. It then calls rpaphp_enable_pci_slot(), -which restarts the device driver and triggers more user-space -events (for example, calling "ifup eth0" for ethernet cards). - - -Device Shutdown and User-Space Events -------------------------------------- -This section documents what happens when a pci slot is unconfigured, -focusing on how the device driver gets shut down, and on how the -events get delivered to user-space scripts. - -Following is an example sequence of events that cause a device driver -close function to be called during the first phase of an EEH reset. -The following sequence is an example of the pcnet32 device driver. - - rpa_php_unconfig_pci_adapter (struct slot *) // in rpaphp_pci.c - { - calls - pci_remove_bus_device (struct pci_dev *) // in /drivers/pci/remove.c - { - calls - pci_destroy_dev (struct pci_dev *) - { - calls - device_unregister (&dev->dev) // in /drivers/base/core.c - { - calls - device_del (struct device *) - { - calls - bus_remove_device() // in /drivers/base/bus.c - { - calls - device_release_driver() - { - calls - struct device_driver->remove() which is just - pci_device_remove() // in /drivers/pci/pci_driver.c - { - calls - struct pci_driver->remove() which is just - pcnet32_remove_one() // in /drivers/net/pcnet32.c - { - calls - unregister_netdev() // in /net/core/dev.c - { - calls - dev_close() // in /net/core/dev.c - { - calls dev->stop(); - which is just pcnet32_close() // in pcnet32.c - { - which does what you wanted - to stop the device - } - } - } - which - frees pcnet32 device driver memory - } - }}}}}} - - - in drivers/pci/pci_driver.c, - struct device_driver->remove() is just pci_device_remove() - which calls struct pci_driver->remove() which is pcnet32_remove_one() - which calls unregister_netdev() (in net/core/dev.c) - which calls dev_close() (in net/core/dev.c) - which calls dev->stop() which is pcnet32_close() - which then does the appropriate shutdown. - ---- -Following is the analogous stack trace for events sent to user-space -when the pci device is unconfigured. - -rpa_php_unconfig_pci_adapter() { // in rpaphp_pci.c - calls - pci_remove_bus_device (struct pci_dev *) { // in /drivers/pci/remove.c - calls - pci_destroy_dev (struct pci_dev *) { - calls - device_unregister (&dev->dev) { // in /drivers/base/core.c - calls - device_del(struct device * dev) { // in /drivers/base/core.c - calls - kobject_del() { //in /libs/kobject.c - calls - kobject_uevent() { // in /libs/kobject.c - calls - kset_uevent() { // in /lib/kobject.c - calls - kset->uevent_ops->uevent() // which is really just - a call to - dev_uevent() { // in /drivers/base/core.c - calls - dev->bus->uevent() which is really just a call to - pci_uevent () { // in drivers/pci/hotplug.c - which prints device name, etc.... - } - } - then kobject_uevent() sends a netlink uevent to userspace - --> userspace uevent - (during early boot, nobody listens to netlink events and - kobject_uevent() executes uevent_helper[], which runs the - event process /sbin/hotplug) - } - } - kobject_del() then calls sysfs_remove_dir(), which would - trigger any user-space daemon that was watching /sysfs, - and notice the delete event. - - -Pro's and Con's of the Current Design -------------------------------------- -There are several issues with the current EEH software recovery design, -which may be addressed in future revisions. But first, note that the -big plus of the current design is that no changes need to be made to -individual device drivers, so that the current design throws a wide net. -The biggest negative of the design is that it potentially disturbs -network daemons and file systems that didn't need to be disturbed. - --- A minor complaint is that resetting the network card causes - user-space back-to-back ifdown/ifup burps that potentially disturb - network daemons, that didn't need to even know that the pci - card was being rebooted. - --- A more serious concern is that the same reset, for SCSI devices, - causes havoc to mounted file systems. Scripts cannot post-facto - unmount a file system without flushing pending buffers, but this - is impossible, because I/O has already been stopped. Thus, - ideally, the reset should happen at or below the block layer, - so that the file systems are not disturbed. - - Reiserfs does not tolerate errors returned from the block device. - Ext3fs seems to be tolerant, retrying reads/writes until it does - succeed. Both have been only lightly tested in this scenario. - - The SCSI-generic subsystem already has built-in code for performing - SCSI device resets, SCSI bus resets, and SCSI host-bus-adapter - (HBA) resets. These are cascaded into a chain of attempted - resets if a SCSI command fails. These are completely hidden - from the block layer. It would be very natural to add an EEH - reset into this chain of events. - --- If a SCSI error occurs for the root device, all is lost unless - the sysadmin had the foresight to run /bin, /sbin, /etc, /var - and so on, out of ramdisk/tmpfs. - - -Conclusions ------------ -There's forward progress ... - - |