diff options
Diffstat (limited to 'Documentation/sound/alsa/ALSA-Configuration.txt')
| -rw-r--r-- | Documentation/sound/alsa/ALSA-Configuration.txt | 69 |
1 files changed, 69 insertions, 0 deletions
diff --git a/Documentation/sound/alsa/ALSA-Configuration.txt b/Documentation/sound/alsa/ALSA-Configuration.txt index 1def6049784c..0ee2c7dfc482 100644 --- a/Documentation/sound/alsa/ALSA-Configuration.txt +++ b/Documentation/sound/alsa/ALSA-Configuration.txt @@ -120,6 +120,34 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed. enable - enable card - Default: enabled, for PCI and ISA PnP cards + Module snd-adlib + ---------------- + + Module for AdLib FM cards. + + port - port # for OPL chip + + This module supports multiple cards. It does not support autoprobe, so + the port must be specified. For actual AdLib FM cards it will be 0x388. + Note that this card does not have PCM support and no mixer; only FM + synthesis. + + Make sure you have "sbiload" from the alsa-tools package available and, + after loading the module, find out the assigned ALSA sequencer port + number through "sbiload -l". Example output: + + Port Client name Port name + 64:0 OPL2 FM synth OPL2 FM Port + + Load the std.sb and drums.sb patches also supplied by sbiload: + + sbiload -p 64:0 std.sb drums.sb + + If you use this driver to drive an OPL3, you can use std.o3 and drums.o3 + instead. To have the card produce sound, use aplaymidi from alsa-utils: + + aplaymidi -p 64:0 foo.mid + Module snd-ad1816a ------------------ @@ -190,6 +218,15 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed. The power-management is supported. + Module snd-als300 + ----------------- + + Module for Avance Logic ALS300 and ALS300+ + + This module supports multiple cards. + + The power-management is supported. + Module snd-als4000 ------------------ @@ -701,6 +738,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed. uniwill 3-jack F1734 2-jack lg LG laptop (m1 express dual) + lg-lw LG LW20 laptop test for testing/debugging purpose, almost all controls can be adjusted. Appearing only when compiled with $CONFIG_SND_DEBUG=y @@ -1013,6 +1051,23 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed. The power-management is supported. + Module snd-miro + --------------- + + Module for Miro soundcards: miroSOUND PCM 1 pro, + miroSOUND PCM 12, + miroSOUND PCM 20 Radio. + + port - Port # (0x530,0x604,0xe80,0xf40) + irq - IRQ # (5,7,9,10,11) + dma1 - 1st dma # (0,1,3) + dma2 - 2nd dma # (0,1) + mpu_port - MPU-401 port # (0x300,0x310,0x320,0x330) + mpu_irq - MPU-401 irq # (5,7,9,10) + fm_port - FM Port # (0x388) + wss - enable WSS mode + ide - enable onboard ide support + Module snd-mixart ----------------- @@ -1202,6 +1257,20 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed. The power-management is supported. + Module snd-riptide + ------------------ + + Module for Conexant Riptide chip + + joystick_port - Joystick port # (default: 0x200) + mpu_port - MPU401 port # (default: 0x330) + opl3_port - OPL3 port # (default: 0x388) + + This module supports multiple cards. + The driver requires the firmware loader support on kernel. + You need to install the firmware file "riptide.hex" to the standard + firmware path (e.g. /lib/firmware). + Module snd-rme32 ---------------- |