3 files changed, 82 insertions, 7 deletions
diff --git a/Documentation/virtual/kvm/devices/s390_flic.txt b/Documentation/virtual/kvm/devices/s390_flic.txt
index c2518cea8ab4..2f1cbf1301d2 100644
--- a/Documentation/virtual/kvm/devices/s390_flic.txt
+++ b/Documentation/virtual/kvm/devices/s390_flic.txt
@@ -16,6 +16,7 @@ FLIC provides support to
 - register and modify adapter interrupt sources (KVM_DEV_FLIC_ADAPTER_*)
 - modify AIS (adapter-interruption-suppression) mode state (KVM_DEV_FLIC_AISM)
 - inject adapter interrupts on a specified adapter (KVM_DEV_FLIC_AIRQ_INJECT)
+- get/set all AIS mode states (KVM_DEV_FLIC_AISM_ALL)
 
 Groups:
   KVM_DEV_FLIC_ENQUEUE
@@ -136,6 +137,20 @@ struct kvm_s390_ais_req {
     an isc according to the adapter-interruption-suppression mode on condition
     that the AIS capability is enabled.
 
+  KVM_DEV_FLIC_AISM_ALL
+    Gets or sets the adapter-interruption-suppression mode for all ISCs. Takes
+    a kvm_s390_ais_all describing:
+
+struct kvm_s390_ais_all {
+       __u8 simm; /* Single-Interruption-Mode mask */
+       __u8 nimm; /* No-Interruption-Mode mask *
+};
+
+    simm contains Single-Interruption-Mode mask for all ISCs, nimm contains
+    No-Interruption-Mode mask for all ISCs. Each bit in simm and nimm corresponds
+    to an ISC (MSB0 bit 0 to ISC 0 and so on). The combination of simm bit and
+    nimm bit presents AIS mode for a ISC.
+
 Note: The KVM_SET_DEVICE_ATTR/KVM_GET_DEVICE_ATTR device ioctls executed on
 FLIC with an unknown group or attribute gives the error code EINVAL (instead of
 ENXIO, as specified in the API documentation). It is not possible to conclude
diff --git a/Documentation/virtual/kvm/devices/vcpu.txt b/Documentation/virtual/kvm/devices/vcpu.txt
index 02f50686c418..2b5dab16c4f2 100644
--- a/Documentation/virtual/kvm/devices/vcpu.txt
+++ b/Documentation/virtual/kvm/devices/vcpu.txt
@@ -16,7 +16,9 @@ Parameters: in kvm_device_attr.addr the address for PMU overflow interrupt is a
 Returns: -EBUSY: The PMU overflow interrupt is already set
          -ENXIO: The overflow interrupt not set when attempting to get it
          -ENODEV: PMUv3 not supported
-         -EINVAL: Invalid PMU overflow interrupt number supplied
+         -EINVAL: Invalid PMU overflow interrupt number supplied or
+                  trying to set the IRQ number without using an in-kernel
+                  irqchip.
 
 A value describing the PMUv3 (Performance Monitor Unit v3) overflow interrupt
 number for this vcpu. This interrupt could be a PPI or SPI, but the interrupt
@@ -25,11 +27,36 @@ all vcpus, while as an SPI it must be a separate number per vcpu.
 
 1.2 ATTRIBUTE: KVM_ARM_VCPU_PMU_V3_INIT
 Parameters: no additional parameter in kvm_device_attr.addr
-Returns: -ENODEV: PMUv3 not supported
-         -ENXIO: PMUv3 not properly configured as required prior to calling this
-                 attribute
+Returns: -ENODEV: PMUv3 not supported or GIC not initialized
+         -ENXIO: PMUv3 not properly configured or in-kernel irqchip not
+                 configured as required prior to calling this attribute
          -EBUSY: PMUv3 already initialized
 
-Request the initialization of the PMUv3.  This must be done after creating the
-in-kernel irqchip.  Creating a PMU with a userspace irqchip is currently not
-supported.
+Request the initialization of the PMUv3.  If using the PMUv3 with an in-kernel
+virtual GIC implementation, this must be done after initializing the in-kernel
+irqchip.
+
+
+2. GROUP: KVM_ARM_VCPU_TIMER_CTRL
+Architectures: ARM,ARM64
+
+2.1. ATTRIBUTE: KVM_ARM_VCPU_TIMER_IRQ_VTIMER
+2.2. ATTRIBUTE: KVM_ARM_VCPU_TIMER_IRQ_PTIMER
+Parameters: in kvm_device_attr.addr the address for the timer interrupt is a
+            pointer to an int
+Returns: -EINVAL: Invalid timer interrupt number
+         -EBUSY:  One or more VCPUs has already run
+
+A value describing the architected timer interrupt number when connected to an
+in-kernel virtual GIC.  These must be a PPI (16 <= intid < 32).  Setting the
+attribute overrides the default values (see below).
+
+KVM_ARM_VCPU_TIMER_IRQ_VTIMER: The EL1 virtual timer intid (default: 27)
+KVM_ARM_VCPU_TIMER_IRQ_PTIMER: The EL1 physical timer intid (default: 30)
+
+Setting the same PPI for different timers will prevent the VCPUs from running.
+Setting the interrupt number on a VCPU configures all VCPUs created at that
+time to use the number provided for a given timer, overwriting any previously
+configured values on other VCPUs.  Userspace should configure the interrupt
+numbers on at least one VCPU after creating all VCPUs and before running any
+VCPUs.
diff --git a/Documentation/virtual/kvm/devices/vm.txt b/Documentation/virtual/kvm/devices/vm.txt
index 575ccb022aac..903fc926860b 100644
--- a/Documentation/virtual/kvm/devices/vm.txt
+++ b/Documentation/virtual/kvm/devices/vm.txt
@@ -222,3 +222,36 @@ Allows user space to disable dea key wrapping, clearing the wrapping key.
 
 Parameters: none
 Returns:    0
+
+5. GROUP: KVM_S390_VM_MIGRATION
+Architectures: s390
+
+5.1. ATTRIBUTE: KVM_S390_VM_MIGRATION_STOP (w/o)
+
+Allows userspace to stop migration mode, needed for PGSTE migration.
+Setting this attribute when migration mode is not active will have no
+effects.
+
+Parameters: none
+Returns:    0
+
+5.2. ATTRIBUTE: KVM_S390_VM_MIGRATION_START (w/o)
+
+Allows userspace to start migration mode, needed for PGSTE migration.
+Setting this attribute when migration mode is already active will have
+no effects.
+
+Parameters: none
+Returns:    -ENOMEM if there is not enough free memory to start migration mode
+	    -EINVAL if the state of the VM is invalid (e.g. no memory defined)
+	    0 in case of success.
+
+5.3. ATTRIBUTE: KVM_S390_VM_MIGRATION_STATUS (r/o)
+
+Allows userspace to query the status of migration mode.
+
+Parameters: address of a buffer in user space to store the data (u64) to;
+	    the data itself is either 0 if migration mode is disabled or 1
+	    if it is enabled
+Returns:    -EFAULT if the given address is not accessible from kernel space
+	    0 in case of success.