aboutsummaryrefslogtreecommitdiffstats
path: root/Documentation/w1/slaves/w1_therm.rst
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/w1/slaves/w1_therm.rst')
-rw-r--r--Documentation/w1/slaves/w1_therm.rst74
1 files changed, 74 insertions, 0 deletions
diff --git a/Documentation/w1/slaves/w1_therm.rst b/Documentation/w1/slaves/w1_therm.rst
new file mode 100644
index 000000000000..90531c340a07
--- /dev/null
+++ b/Documentation/w1/slaves/w1_therm.rst
@@ -0,0 +1,74 @@
+======================
+Kernel driver w1_therm
+======================
+
+Supported chips:
+
+ * Maxim ds18*20 based temperature sensors.
+ * Maxim ds1825 based temperature sensors.
+
+Author: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
+
+
+Description
+-----------
+
+w1_therm provides basic temperature conversion for ds18*20 devices, and the
+ds28ea00 device.
+
+Supported family codes:
+
+==================== ====
+W1_THERM_DS18S20 0x10
+W1_THERM_DS1822 0x22
+W1_THERM_DS18B20 0x28
+W1_THERM_DS1825 0x3B
+W1_THERM_DS28EA00 0x42
+==================== ====
+
+Support is provided through the sysfs w1_slave file. Each open and
+read sequence will initiate a temperature conversion then provide two
+lines of ASCII output. The first line contains the nine hex bytes
+read along with a calculated crc value and YES or NO if it matched.
+If the crc matched the returned values are retained. The second line
+displays the retained values along with a temperature in millidegrees
+Centigrade after t=.
+
+Parasite powered devices are limited to one slave performing a
+temperature conversion at a time. If none of the devices are parasite
+powered it would be possible to convert all the devices at the same
+time and then go back to read individual sensors. That isn't
+currently supported. The driver also doesn't support reduced
+precision (which would also reduce the conversion time) when reading values.
+
+Writing a value between 9 and 12 to the sysfs w1_slave file will change the
+precision of the sensor for the next readings. This value is in (volatile)
+SRAM, so it is reset when the sensor gets power-cycled.
+
+To store the current precision configuration into EEPROM, the value 0
+has to be written to the sysfs w1_slave file. Since the EEPROM has a limited
+amount of writes (>50k), this command should be used wisely.
+
+The module parameter strong_pullup can be set to 0 to disable the
+strong pullup, 1 to enable autodetection or 2 to force strong pullup.
+In case of autodetection, the driver will use the "READ POWER SUPPLY"
+command to check if there are pariste powered devices on the bus.
+If so, it will activate the master's strong pullup.
+In case the detection of parasite devices using this command fails
+(seems to be the case with some DS18S20) the strong pullup can
+be force-enabled.
+
+If the strong pullup is enabled, the master's strong pullup will be
+driven when the conversion is taking place, provided the master driver
+does support the strong pullup (or it falls back to a pullup
+resistor). The DS18b20 temperature sensor specification lists a
+maximum current draw of 1.5mA and that a 5k pullup resistor is not
+sufficient. The strong pullup is designed to provide the additional
+current required.
+
+The DS28EA00 provides an additional two pins for implementing a sequence
+detection algorithm. This feature allows you to determine the physical
+location of the chip in the 1-wire bus without needing pre-existing
+knowledge of the bus ordering. Support is provided through the sysfs
+w1_seq file. The file will contain a single line with an integer value
+representing the device index in the bus starting at 0.