diff options
Diffstat (limited to 'Documentation')
73 files changed, 1363 insertions, 91 deletions
diff --git a/Documentation/DocBook/media/v4l/media-types.xml b/Documentation/DocBook/media/v4l/media-types.xml index 1af384250910..0ee0f3386cdf 100644 --- a/Documentation/DocBook/media/v4l/media-types.xml +++ b/Documentation/DocBook/media/v4l/media-types.xml @@ -57,10 +57,6 @@ <entry>Connector for a RGB composite signal.</entry> </row> <row> - <entry><constant>MEDIA_ENT_F_CONN_TEST</constant></entry> - <entry>Connector for a test generator.</entry> - </row> - <row> <entry><constant>MEDIA_ENT_F_CAM_SENSOR</constant></entry> <entry>Camera video sensor entity.</entry> </row> diff --git a/Documentation/Intel-IOMMU.txt b/Documentation/Intel-IOMMU.txt index 7b57fc087088..49585b6e1ea2 100644 --- a/Documentation/Intel-IOMMU.txt +++ b/Documentation/Intel-IOMMU.txt @@ -3,7 +3,7 @@ Linux IOMMU Support The architecture spec can be obtained from the below location. -http://www.intel.com/technology/virtualization/ +http://www.intel.com/content/dam/www/public/us/en/documents/product-specifications/vt-directed-io-spec.pdf This guide gives a quick cheat sheet for some basic understanding. diff --git a/Documentation/cgroup-v2.txt b/Documentation/cgroup-v2.txt index 65b3eac8856c..ff49cf901148 100644 --- a/Documentation/cgroup-v2.txt +++ b/Documentation/cgroup-v2.txt @@ -7,7 +7,7 @@ This is the authoritative documentation on the design, interface and conventions of cgroup v2. It describes all userland-visible aspects of cgroup including core and specific controller behaviors. All future changes must be reflected in this document. Documentation for -v1 is available under Documentation/cgroup-legacy/. +v1 is available under Documentation/cgroup-v1/. CONTENTS @@ -843,6 +843,10 @@ PAGE_SIZE multiple when read back. Amount of memory used to cache filesystem data, including tmpfs and shared memory. + sock + + Amount of memory used in network transmission buffers + file_mapped Amount of cached filesystem data mapped with mmap() diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index a2bd593881ca..66422d663184 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -23,6 +23,7 @@ Optional properties: during suspend. - ti,no-reset-on-init: When present, the module should not be reset at init - ti,no-idle-on-init: When present, the module should not be idled at init +- ti,no-idle: When present, the module is never allowed to idle. Example: diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt index ace05992a262..20df350b9ef3 100644 --- a/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt @@ -30,7 +30,7 @@ that they are defined using standard clock bindings with following clock-output-names: - "xin24m" - crystal input - required, - "ext_i2s" - external I2S clock - optional, - - "ext_gmac" - external GMAC clock - optional + - "rmii_clkin" - external EMAC clock - optional Example: Clock controller node: diff --git a/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt b/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt new file mode 100644 index 000000000000..ef3752889496 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt @@ -0,0 +1,49 @@ +* Microchip PIC32 GPIO devices (PIO). + +Required properties: + - compatible: "microchip,pic32mzda-gpio" + - reg: Base address and length for the device. + - interrupts: The port interrupt shared by all pins. + - gpio-controller: Marks the port as GPIO controller. + - #gpio-cells: Two. The first cell is the pin number and + the second cell is used to specify the gpio polarity as defined in + defined in <dt-bindings/gpio/gpio.h>: + 0 = GPIO_ACTIVE_HIGH + 1 = GPIO_ACTIVE_LOW + 2 = GPIO_OPEN_DRAIN + - interrupt-controller: Marks the device node as an interrupt controller. + - #interrupt-cells: Two. The first cell is the GPIO number and second cell + is used to specify the trigger type as defined in + <dt-bindings/interrupt-controller/irq.h>: + IRQ_TYPE_EDGE_RISING + IRQ_TYPE_EDGE_FALLING + IRQ_TYPE_EDGE_BOTH + - clocks: Clock specifier (see clock bindings for details). + - microchip,gpio-bank: Specifies which bank a controller owns. + - gpio-ranges: Interaction with the PINCTRL subsystem. + +Example: + +/* PORTA */ +gpio0: gpio0@1f860000 { + compatible = "microchip,pic32mzda-gpio"; + reg = <0x1f860000 0x100>; + interrupts = <118 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&PBCLK4>; + microchip,gpio-bank = <0>; + gpio-ranges = <&pic32_pinctrl 0 0 16>; +}; + +keys { + ... + + button@sw1 { + label = "ESC"; + linux,code = <1>; + gpios = <&gpio0 12 0>; + }; +}; diff --git a/Documentation/devicetree/bindings/hwmon/nsa320-mcu.txt b/Documentation/devicetree/bindings/hwmon/nsa320-mcu.txt new file mode 100644 index 000000000000..0863e067c85b --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/nsa320-mcu.txt @@ -0,0 +1,20 @@ +Bindings for the fan / temperature monitor microcontroller used on +the Zyxel NSA 320 and several subsequent models. + +Required properties: +- compatible : "zyxel,nsa320-mcu" +- data-gpios : The GPIO pin connected to the data line on the MCU +- clk-gpios : The GPIO pin connected to the clock line on the MCU +- act-gpios : The GPIO pin connected to the active line on the MCU + +Example: + + hwmon { + compatible = "zyxel,nsa320-mcu"; + pinctrl-0 = <&pmx_mcu_data &pmx_mcu_clk &pmx_mcu_act>; + pinctrl-names = "default"; + + data-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; + clk-gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>; + act-gpios = <&gpio0 17 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt index a04a80f9cc70..c3b9c4cfe8df 100644 --- a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt +++ b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt @@ -10,6 +10,7 @@ Requires node properties: "murata,ncp03wb473" "murata,ncp15wl333" "murata,ncp03wf104" + "murata,ncp15xh103" /* Usage of vendor name "ntc" is deprecated */ <DEPRECATED> "ntc,ncp15wb473" diff --git a/Documentation/devicetree/bindings/iio/iio-bindings.txt b/Documentation/devicetree/bindings/iio/iio-bindings.txt index 0b447d9ad196..68d6f8ce063b 100644 --- a/Documentation/devicetree/bindings/iio/iio-bindings.txt +++ b/Documentation/devicetree/bindings/iio/iio-bindings.txt @@ -82,7 +82,7 @@ vdd channel is connected to output 0 of the &ref device. ... - iio_hwmon { + iio-hwmon { compatible = "iio-hwmon"; io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, <&adc 4>, <&adc 5>, diff --git a/Documentation/devicetree/bindings/interrupt-controller/al,alpine-msix.txt b/Documentation/devicetree/bindings/interrupt-controller/al,alpine-msix.txt new file mode 100644 index 000000000000..f6f1c14bf99b --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/al,alpine-msix.txt @@ -0,0 +1,26 @@ +Alpine MSIX controller + +See arm,gic-v3.txt for SPI and MSI definitions. + +Required properties: + +- compatible: should be "al,alpine-msix" +- reg: physical base address and size of the registers +- interrupt-parent: specifies the parent interrupt controller. +- interrupt-controller: identifies the node as an interrupt controller +- msi-controller: identifies the node as an PCI Message Signaled Interrupt + controller +- al,msi-base-spi: SPI base of the MSI frame +- al,msi-num-spis: number of SPIs assigned to the MSI frame, relative to SPI0 + +Example: + +msix: msix { + compatible = "al,alpine-msix"; + reg = <0x0 0xfbe00000 0x0 0x100000>; + interrupt-parent = <&gic>; + interrupt-controller; + msi-controller; + al,msi-base-spi = <160>; + al,msi-num-spis = <160>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt index 7803e77d85cb..007a5b46256a 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt @@ -24,9 +24,8 @@ Main node required properties: 1 = edge triggered 4 = level triggered - Cells 4 and beyond are reserved for future use. When the 1st cell - has a value of 0 or 1, cells 4 and beyond act as padding, and may be - ignored. It is recommended that padding cells have a value of 0. + Cells 4 and beyond are reserved for future use and must have a value + of 0 if present. - reg : Specifies base physical address(s) and size of the GIC registers, in the following order: diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt index 5a1cb4bc3dfe..793c20ff8fcc 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt @@ -16,6 +16,7 @@ Main node required properties: "arm,cortex-a15-gic" "arm,cortex-a7-gic" "arm,cortex-a9-gic" + "arm,eb11mp-gic" "arm,gic-400" "arm,pl390" "arm,tc11mp-gic" diff --git a/Documentation/devicetree/bindings/interrupt-controller/marvell,odmi-controller.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,odmi-controller.txt new file mode 100644 index 000000000000..8af0a8e613ab --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/marvell,odmi-controller.txt @@ -0,0 +1,44 @@ + +* Marvell ODMI for MSI support + +Some Marvell SoCs have an On-Die Message Interrupt (ODMI) controller +which can be used by on-board peripheral for MSI interrupts. + +Required properties: + +- compatible : The value here should contain: + + "marvell,ap806-odmi-controller", "marvell,odmi-controller". + +- interrupt,controller : Identifies the node as an interrupt controller. + +- msi-controller : Identifies the node as an MSI controller. + +- marvell,odmi-frames : Number of ODMI frames available. Each frame + provides a number of events. + +- reg : List of register definitions, one for each + ODMI frame. + +- marvell,spi-base : List of GIC base SPI interrupts, one for each + ODMI frame. Those SPI interrupts are 0-based, + i.e marvell,spi-base = <128> will use SPI #96. + See Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt + for details about the GIC Device Tree binding. + +- interrupt-parent : Reference to the parent interrupt controller. + +Example: + + odmi: odmi@300000 { + compatible = "marvell,ap806-odm-controller", + "marvell,odmi-controller"; + interrupt-controller; + msi-controller; + marvell,odmi-frames = <4>; + reg = <0x300000 0x4000>, + <0x304000 0x4000>, + <0x308000 0x4000>, + <0x30C000 0x4000>; + marvell,spi-base = <128>, <136>, <144>, <152>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt b/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt index aae4c384ee1f..173595305e26 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt @@ -23,6 +23,12 @@ Optional properties: - mti,reserved-cpu-vectors : Specifies the list of CPU interrupt vectors to which the GIC may not route interrupts. Valid values are 2 - 7. This property is ignored if the CPU is started in EIC mode. +- mti,reserved-ipi-vectors : Specifies the range of GIC interrupts that are + reserved for IPIs. + It accepts 2 values, the 1st is the starting interrupt and the 2nd is the size + of the reserved range. + If not specified, the driver will allocate the last 2 * number of VPEs in the + system. Required properties for timer sub-node: - compatible : Should be "mti,gic-timer". @@ -44,6 +50,7 @@ Example: #interrupt-cells = <3>; mti,reserved-cpu-vectors = <7>; + mti,reserved-ipi-vectors = <40 8>; timer { compatible = "mti,gic-timer"; diff --git a/Documentation/devicetree/bindings/interrupt-controller/sigma,smp8642-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/sigma,smp8642-intc.txt new file mode 100644 index 000000000000..1f441fa0ad40 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/sigma,smp8642-intc.txt @@ -0,0 +1,49 @@ +Sigma Designs SMP86xx/SMP87xx secondary interrupt controller + +Required properties: +- compatible: should be "sigma,smp8642-intc" +- reg: physical address of MMIO region +- ranges: address space mapping of child nodes +- interrupt-parent: phandle of parent interrupt controller +- interrupt-controller: boolean +- #address-cells: should be <1> +- #size-cells: should be <1> + +One child node per control block with properties: +- reg: address of registers for this control block +- interrupt-controller: boolean +- #interrupt-cells: should be <2>, interrupt index and flags per interrupts.txt +- interrupts: interrupt spec of primary interrupt controller + +Example: + +interrupt-controller@6e000 { + compatible = "sigma,smp8642-intc"; + reg = <0x6e000 0x400>; + ranges = <0x0 0x6e000 0x400>; + interrupt-parent = <&gic>; + interrupt-controller; + #address-cells = <1>; + #size-cells = <1>; + + irq0: interrupt-controller@0 { + reg = <0x000 0x100>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; + }; + + irq1: interrupt-controller@100 { + reg = <0x100 0x100>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; + }; + + irq2: interrupt-controller@300 { + reg = <0x300 0x100>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt b/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt index 451fef26b4df..10587bdadbbe 100644 --- a/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt +++ b/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt @@ -68,7 +68,7 @@ ethernet@f0b60000 { phy1: ethernet-phy@1 { max-speed = <1000>; reg = <0x1>; - compatible = "brcm,28nm-gphy", "ethernet-phy-ieee802.3-c22"; + compatible = "ethernet-phy-ieee802.3-c22"; }; }; }; @@ -115,7 +115,7 @@ ethernet@f0ba0000 { phy0: ethernet-phy@0 { max-speed = <1000>; reg = <0x0>; - compatible = "brcm,bcm53125", "ethernet-phy-ieee802.3-c22"; + compatible = "ethernet-phy-ieee802.3-c22"; }; }; }; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt index 80411b2f0490..ecacfa44b1eb 100644 --- a/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt @@ -4,8 +4,6 @@ Required properties: - compatible: should be "hisilicon,hns-dsaf-v1" or "hisilicon,hns-dsaf-v2". "hisilicon,hns-dsaf-v1" is for hip05. "hisilicon,hns-dsaf-v2" is for Hi1610 and Hi1612. -- dsa-name: dsa fabric name who provide this interface. - should be "dsafX", X is the dsaf id. - mode: dsa fabric mode string. only support one of dsaf modes like these: "2port-64vf", "6port-16rss", @@ -26,9 +24,8 @@ Required properties: Example: -dsa: dsa@c7000000 { +dsaf0: dsa@c7000000 { compatible = "hisilicon,hns-dsaf-v1"; - dsa_name = "dsaf0"; mode = "6port-16rss"; interrupt-parent = <&mbigen_dsa>; reg = <0x0 0xC0000000 0x0 0x420000 diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt index 41d19be7011e..e6a9d1c30878 100644 --- a/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt @@ -4,8 +4,9 @@ Required properties: - compatible: "hisilicon,hns-nic-v1" or "hisilicon,hns-nic-v2". "hisilicon,hns-nic-v1" is for hip05. "hisilicon,hns-nic-v2" is for Hi1610 and Hi1612. -- ae-name: accelerator name who provides this interface, - is simply a name referring to the name of name in the accelerator node. +- ae-handle: accelerator engine handle for hns, + specifies a reference to the associating hardware driver node. + see Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt - port-id: is the index of port provided by DSAF (the accelerator). DSAF can connect to 8 PHYs. Port 0 to 1 are both used for adminstration purpose. They are called debug ports. @@ -41,7 +42,7 @@ Example: ethernet@0{ compatible = "hisilicon,hns-nic-v1"; - ae-name = "dsaf0"; + ae-handle = <&dsaf0>; port-id = <0>; local-mac-address = [a2 14 e4 4b 56 76]; }; diff --git a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt index aeea50c84e92..d0cb8693963b 100644 --- a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt +++ b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt @@ -6,12 +6,17 @@ Required properties: - interrupts: interrupt for the device - phy: See ethernet.txt file in the same directory. - phy-mode: See ethernet.txt file in the same directory -- clocks: a pointer to the reference clock for this device. +- clocks: List of clocks for this device. At least one clock is + mandatory for the core clock. If several clocks are given, then the + clock-names property must be used to identify them. Optional properties: - tx-csum-limit: maximum mtu supported by port that allow TX checksum. Value is presented in bytes. If not used, by default 1600B is set for "marvell,armada-370-neta" and 9800B for others. +- clock-names: List of names corresponding to clocks property; shall be + "core" for core clock and "bus" for the optional bus clock. + Example: diff --git a/Documentation/devicetree/bindings/net/mdio-mux-gpio.txt b/Documentation/devicetree/bindings/net/mdio-mux-gpio.txt index 79384113c2b0..694987d3c17a 100644 --- a/Documentation/devicetree/bindings/net/mdio-mux-gpio.txt +++ b/Documentation/devicetree/bindings/net/mdio-mux-gpio.txt @@ -38,7 +38,6 @@ Example : phy11: ethernet-phy@1 { reg = <1>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -48,7 +47,6 @@ Example : }; phy12: ethernet-phy@2 { reg = <2>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -58,7 +56,6 @@ Example : }; phy13: ethernet-phy@3 { reg = <3>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -68,7 +65,6 @@ Example : }; phy14: ethernet-phy@4 { reg = <4>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -85,7 +81,6 @@ Example : phy21: ethernet-phy@1 { reg = <1>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -95,7 +90,6 @@ Example : }; phy22: ethernet-phy@2 { reg = <2>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -105,7 +99,6 @@ Example : }; phy23: ethernet-phy@3 { reg = <3>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -115,7 +108,6 @@ Example : }; phy24: ethernet-phy@4 { reg = <4>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, diff --git a/Documentation/devicetree/bindings/net/mdio-mux.txt b/Documentation/devicetree/bindings/net/mdio-mux.txt index f65606f8d632..491f5bd55203 100644 --- a/Documentation/devicetree/bindings/net/mdio-mux.txt +++ b/Documentation/devicetree/bindings/net/mdio-mux.txt @@ -47,7 +47,6 @@ Example : phy11: ethernet-phy@1 { reg = <1>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -57,7 +56,6 @@ Example : }; phy12: ethernet-phy@2 { reg = <2>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -67,7 +65,6 @@ Example : }; phy13: ethernet-phy@3 { reg = <3>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -77,7 +74,6 @@ Example : }; phy14: ethernet-phy@4 { reg = <4>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -94,7 +90,6 @@ Example : phy21: ethernet-phy@1 { reg = <1>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -104,7 +99,6 @@ Example : }; phy22: ethernet-phy@2 { reg = <2>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -114,7 +108,6 @@ Example : }; phy23: ethernet-phy@3 { reg = <3>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, @@ -124,7 +117,6 @@ Example : }; phy24: ethernet-phy@4 { reg = <4>; - compatible = "marvell,88e1149r"; marvell,reg-init = <3 0x10 0 0x5777>, <3 0x11 0 0x00aa>, <3 0x12 0 0x4105>, diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt index 525e1658f2da..bc1c3c8bf8fa 100644 --- a/Documentation/devicetree/bindings/net/phy.txt +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -17,8 +17,7 @@ Optional Properties: "ethernet-phy-ieee802.3-c22" or "ethernet-phy-ieee802.3-c45" for PHYs that implement IEEE802.3 clause 22 or IEEE802.3 clause 45 specifications. If neither of these are specified, the default is to - assume clause 22. The compatible list may also contain other - elements. + assume clause 22. If the phy's identifier is known then the list may contain an entry of the form: "ethernet-phy-idAAAA.BBBB" where @@ -28,6 +27,9 @@ Optional Properties: 4 hex digits. This is the chip vendor OUI bits 19:24, followed by 10 bits of a vendor specific ID. + The compatible list should not contain other values than those + listed here. + - max-speed: Maximum PHY supported speed (10, 100, 1000...) - broken-turn-around: If set, indicates the PHY device does not correctly diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt index 81a9f9e6b45f..c8ac222eac67 100644 --- a/Documentation/devicetree/bindings/net/renesas,ravb.txt +++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt @@ -82,8 +82,8 @@ Example: "ch16", "ch17", "ch18", "ch19", "ch20", "ch21", "ch22", "ch23", "ch24"; - clocks = <&mstp8_clks R8A7795_CLK_ETHERAVB>; - power-domains = <&cpg_clocks>; + clocks = <&cpg CPG_MOD 812>; + power-domains = <&cpg>; phy-mode = "rgmii-id"; phy-handle = <&phy0>; diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt index 4e8b90e43dd8..07a75094c5a8 100644 --- a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt +++ b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt @@ -8,6 +8,7 @@ OHCI and EHCI controllers. Required properties: - compatible: "renesas,pci-r8a7790" for the R8A7790 SoC; "renesas,pci-r8a7791" for the R8A7791 SoC; + "renesas,pci-r8a7793" for the R8A7793 SoC; "renesas,pci-r8a7794" for the R8A7794 SoC; "renesas,pci-rcar-gen2" for a generic R-Car Gen2 compatible device diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt index 558fe528ae19..6cf99690eef9 100644 --- a/Documentation/devicetree/bindings/pci/rcar-pci.txt +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -4,6 +4,7 @@ Required properties: compatible: "renesas,pcie-r8a7779" for the R8A7779 SoC; "renesas,pcie-r8a7790" for the R8A7790 SoC; "renesas,pcie-r8a7791" for the R8A7791 SoC; + "renesas,pcie-r8a7793" for the R8A7793 SoC; "renesas,pcie-r8a7795" for the R8A7795 SoC; "renesas,pcie-rcar-gen2" for a generic R-Car Gen2 compatible device. diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index 9213b27e1036..69617220c5d6 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -21,6 +21,8 @@ Required properties: "allwinner,sun9i-a80-r-pinctrl" "allwinner,sun8i-a83t-pinctrl" "allwinner,sun8i-h3-pinctrl" + "allwinner,sun8i-h3-r-pinctrl" + "allwinner,sun50i-a64-pinctrl" - reg: Should contain the register physical address and length for the pin controller. diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,ns2-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/brcm,ns2-pinmux.txt new file mode 100644 index 000000000000..e295dda4bbba --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/brcm,ns2-pinmux.txt @@ -0,0 +1,102 @@ +Broadcom Northstar2 IOMUX Controller + +The Northstar2 IOMUX controller supports group based mux configuration. There +are some individual pins that support modifying the pinconf parameters. + +Required properties: + +- compatible: + Must be "brcm,ns2-pinmux" + +- reg: + Define the base and range of the I/O address space that contains the + Northstar2 IOMUX and pin configuration registers. + +Properties in sub nodes: + +- function: + The mux function to select + +- groups: + The list of groups to select with a given function + +- pins: + List of pin names to change configuration + +The generic properties bias-disable, bias-pull-down, bias-pull-up, +drive-strength, slew-rate, input-enable, input-disable are supported +for some individual pins listed at the end. + +For more details, refer to +Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +For example: + + pinctrl: pinctrl@6501d130 { + compatible = "brcm,ns2-pinmux"; + reg = <0x6501d130 0x08>, + <0x660a0028 0x04>, + <0x660009b0 0x40>; + + pinctrl-names = "default"; + pinctrl-0 = <&nand_sel &uart3_rx &sdio0_d4>; + + /* Select nand function */ + nand_sel: nand_sel { + function = "nand"; + groups = "nand_grp"; + }; + + /* Pull up the uart3 rx pin */ + uart3_rx: uart3_rx { + pins = "uart3_sin"; + bias-pull-up; + }; + + /* Set the drive strength of sdio d4 pin */ + sdio0_d4: sdio0_d4 { + pins = "sdio0_data4"; + drive-strength = <8>; + }; + }; + +List of supported functions and groups in Northstar2: + +"nand": "nand_grp" + +"nor": "nor_data_grp", "nor_adv_grp", "nor_addr_0_3_grp", "nor_addr_4_5_grp", + "nor_addr_6_7_grp", "nor_addr_8_9_grp", "nor_addr_10_11_grp", + "nor_addr_12_15_grp" + +"gpio": "gpio_0_1_grp", "gpio_2_5_grp", "gpio_6_7_grp", "gpio_8_9_grp", + "gpio_10_11_grp", "gpio_12_13_grp", "gpio_14_17_grp", "gpio_18_19_grp", + "gpio_20_21_grp", "gpio_22_23_grp", "gpio_24_25_grp", "gpio_26_27_grp", + "gpio_28_29_grp", "gpio_30_31_grp" + +"pcie": "pcie_ab1_clk_wak_grp", "pcie_a3_clk_wak_grp", "pcie_b3_clk_wak_grp", + "pcie_b2_clk_wak_grp", "pcie_a2_clk_wak_grp" + +"uart0": "uart0_modem_grp", "uart0_rts_cts_grp", "uart0_in_out_grp" + +"uart1": "uart1_ext_clk_grp", "uart1_dcd_dsr_grp", "uart1_ri_dtr_grp", + "uart1_rts_cts_grp", "uart1_in_out_grp" + +"uart2": "uart2_rts_cts_grp" + +"pwm": "pwm_0_grp", "pwm_1_grp", "pwm_2_grp", "pwm_3_grp" + + +List of pins that support pinconf parameters: + +"qspi_wp", "qspi_hold", "qspi_cs", "qspi_sck", "uart3_sin", "uart3_sout", +"qspi_mosi", "qspi_miso", "spi0_fss", "spi0_rxd", "spi0_txd", "spi0_sck", +"spi1_fss", "spi1_rxd", "spi1_txd", "spi1_sck", "sdio0_data7", +"sdio0_emmc_rst", "sdio0_led_on", "sdio0_wp", "sdio0_data3", "sdio0_data4", +"sdio0_data5", "sdio0_data6", "sdio0_cmd", "sdio0_data0", "sdio0_data1", +"sdio0_data2", "sdio1_led_on", "sdio1_wp", "sdio0_cd_l", "sdio0_clk", +"sdio1_data5", "sdio1_data6", "sdio1_data7", "sdio1_emmc_rst", "sdio1_data1", +"sdio1_data2", "sdio1_data3", "sdio1_data4", "sdio1_cd_l", "sdio1_clk", +"sdio1_cmd", "sdio1_data0", "ext_mdio_0", "ext_mdc_0", "usb3_p1_vbus_ppc", +"usb3_p1_overcurrent", "usb3_p0_vbus_ppc", "usb3_p0_overcurrent", +"usb2_presence_indication", "usb2_vbus_present", "usb2_vbus_ppc", +"usb2_overcurrent", "sata_led1", "sata_led0" diff --git a/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt new file mode 100644 index 000000000000..4b5efa51bec7 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt @@ -0,0 +1,60 @@ +* Microchip PIC32 Pin Controller + +Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and +../interrupt-controller/interrupts.txt for generic information regarding +pin controller, GPIO, and interrupt bindings. + +PIC32 'pin configuration node' is a node of a group of pins which can be +used for a specific device or function. This node represents configuraions of +pins, optional function, and optional mux related configuration. + +Required properties for pin controller node: + - compatible: "microchip,pic32mada-pinctrl" + - reg: Address range of the pinctrl registers. + - clocks: Clock specifier (see clock bindings for details) + +Required properties for pin configuration sub-nodes: + - pins: List of pins to which the configuration applies. + +Optional properties for pin configuration sub-nodes: +---------------------------------------------------- + - function: Mux function for the specified pins. + - bias-pull-up: Enable weak pull-up. + - bias-pull-down: Enable weak pull-down. + - input-enable: Set the pin as an input. + - output-low: Set the pin as an output level low. + - output-high: Set the pin as an output level high. + - microchip,digital: Enable digital I/O. + - microchip,analog: Enable analog I/O. + +Example: + +pic32_pinctrl: pinctrl@1f801400{ + #address-cells = <1>; + #size-cells = <1>; + compatible = "microchip,pic32mzda-pinctrl"; + reg = <0x1f801400 0x400>; + clocks = <&PBCLK1>; + + pinctrl_uart2: pinctrl_uart2 { + uart2-tx { + pins = "G9"; + function = "U2TX"; + microchip,digital; + output-low; + }; + uart2-rx { + pins = "B0"; + function = "U2RX"; + microchip,digital; + input-enable; + }; + }; +}; + +uart2: serial@1f822200 { + compatible = "microchip,pic32mzda-uart"; + reg = <0x1f822200 0x50>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/nxp,lpc1850-scu.txt b/Documentation/devicetree/bindings/pinctrl/nxp,lpc1850-scu.txt index df0309c57505..bd8b0c69fa44 100644 --- a/Documentation/devicetree/bindings/pinctrl/nxp,lpc1850-scu.txt +++ b/Documentation/devicetree/bindings/pinctrl/nxp,lpc1850-scu.txt @@ -22,6 +22,10 @@ The following generic nodes are supported: - input-schmitt-disable - slew-rate +NXP specific properties: + - nxp,gpio-pin-interrupt : Assign pin to gpio pin interrupt controller + irq number 0 to 7. See example below. + Not all pins support all properties so either refer to the NXP 1850/4350 user manual or the pin table in the pinctrl-lpc18xx driver for supported pin properties. @@ -54,4 +58,14 @@ pinctrl: pinctrl@40086000 { bias-disable; }; }; + + gpio_joystick_pins: gpio-joystick-pins { + gpio_joystick_1_cfg { + pins = "p9_0"; + function = "gpio"; + nxp,gpio-pin-interrupt = <0>; + input-enable; + bias-disable; + }; + }; }; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt index 9ffb0b276bb4..17631d0a9af7 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt @@ -6,6 +6,7 @@ Required properties: - compatible: value should be one of the following. "mediatek,mt2701-pinctrl", compatible with mt2701 pinctrl. "mediatek,mt6397-pinctrl", compatible with mt6397 pinctrl. + "mediatek,mt7623-pinctrl", compatible with mt7623 pinctrl. "mediatek,mt8127-pinctrl", compatible with mt8127 pinctrl. "mediatek,mt8135-pinctrl", compatible with mt8135 pinctrl. "mediatek,mt8173-pinctrl", compatible with mt8173 pinctrl. diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt new file mode 100644 index 000000000000..cfb8500dd56b --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt @@ -0,0 +1,74 @@ +Qualcomm Atheros IPQ4019 TLMM block + +This is the Top Level Mode Multiplexor block found on the Qualcomm IPQ8019 +platform, it provides pinctrl, pinmux, pinconf, and gpiolib facilities. + +Required properties: +- compatible: "qcom,ipq4019-pinctrl" +- reg: Should be the base address and length of the TLMM block. +- interrupts: Should be the parent IRQ of the TLMM block. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Should be two. +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells : Should be two. + The first cell is the gpio pin number and the + second cell is used for optional parameters. + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an abitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength. + +Non-empty subnodes must specify the 'pins' property. +Note that not all properties are valid for all pins. + + +Valid values for qcom,pins are: + gpio0-gpio99 + Supports mux, bias and drive-strength + +Valid values for qcom,function are: +gpio, blsp_uart1, blsp_i2c0, blsp_i2c1, blsp_uart0, blsp_spi1, blsp_spi0 + +Example: + + tlmm: pinctrl@1000000 { + compatible = "qcom,ipq4019-pinctrl"; + reg = <0x1000000 0x300000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 208 0>; + + serial_pins: serial_pinmux { + mux { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt index 0cd701b1947f..c68b9554561f 100644 --- a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt @@ -22,7 +22,7 @@ Required properties for iomux controller: - compatible: one of "rockchip,rk2928-pinctrl", "rockchip,rk3066a-pinctrl" "rockchip,rk3066b-pinctrl", "rockchip,rk3188-pinctrl" "rockchip,rk3228-pinctrl", "rockchip,rk3288-pinctrl" - "rockchip,rk3368-pinctrl" + "rockchip,rk3368-pinctrl", "rockchip,rk3399-pinctrl" - rockchip,grf: phandle referencing a syscon providing the "general register files" diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt new file mode 100644 index 000000000000..7b4800cc251e --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt @@ -0,0 +1,126 @@ +* STM32 GPIO and Pin Mux/Config controller + +STMicroelectronics's STM32 MCUs intregrate a GPIO and Pin mux/config hardware +controller. It controls the input/output settings on the available pins and +also provides ability to multiplex and configure the output of various on-chip +controllers onto these pads. + +Pin controller node: +Required properies: + - compatible: value should be one of the following: + (a) "st,stm32f429-pinctrl" + - #address-cells: The value of this property must be 1 + - #size-cells : The value of this property must be 1 + - ranges : defines mapping between pin controller node (parent) to + gpio-bank node (children). + - pins-are-numbered: Specify the subnodes are using numbered pinmux to + specify pins. + +GPIO controller/bank node: +Required properties: + - gpio-controller : Indicates this device is a GPIO controller + - #gpio-cells : Should be two. + The first cell is the pin number + The second one is the polarity: + - 0 for active high + - 1 for active low + - reg : The gpio address range, relative to the pinctrl range + - clocks : clock that drives this bank + - st,bank-name : Should be a name string for this bank as specified in + the datasheet + +Optional properties: + - reset: : Reference to the reset controller + +Example: +#include <dt-bindings/pinctrl/stm32f429-pinfunc.h> +... + + pin-controller { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,stm32f429-pinctrl"; + ranges = <0 0x40020000 0x3000>; + pins-are-numbered; + + gpioa: gpio@40020000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x0 0x400>; + resets = <&reset_ahb1 0>; + st,bank-name = "GPIOA"; + }; + ... + pin-functions nodes follow... + }; + +Contents of function subnode node: +---------------------------------- +Subnode format +A pinctrl node should contain at least one subnode representing the +pinctrl group available on the machine. Each subnode will list the +pins it needs, and how they should be configured, with regard to muxer +configuration, pullups, drive, output high/low and output speed. + + node { + pinmux = <PIN_NUMBER_PINMUX>; + GENERIC_PINCONFIG; + }; + +Required properties: +- pinmux: integer array, represents gpio pin number and mux setting. + Supported pin number and mux varies for different SoCs, and are defined in + dt-bindings/pinctrl/<soc>-pinfunc.h directly. + These defines are calculated as: + ((port * 16 + line) << 8) | function + With: + - port: The gpio port index (PA = 0, PB = 1, ..., PK = 11) + - line: The line offset within the port (PA0 = 0, PA1 = 1, ..., PA15 = 15) + - function: The function number, can be: + * 0 : GPIO + * 1 : Alternate Function 0 + * 2 : Alternate Function 1 + * 3 : Alternate Function 2 + * ... + * 16 : Alternate Function 15 + * 17 : Analog + +Optional properties: +- GENERIC_PINCONFIG: is the generic pinconfig options to use. + Available options are: + - bias-disable, + - bias-pull-down, + - bias-pull-up, + - drive-push-pull, + - drive-open-drain, + - output-low + - output-high + - slew-rate = <x>, with x being: + < 0 > : Low speed + < 1 > : Medium speed + < 2 > : Fast speed + < 3 > : High speed + +Example: + +pin-controller { +... + usart1_pins_a: usart1@0 { + pins1 { + pinmux = <STM32F429_PA9_FUNC_USART1_TX>; + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32F429_PA10_FUNC_USART1_RX>; + bias-disable; + }; + }; +}; + +&usart1 { + pinctrl-0 = <&usart1_pins_a>; + pinctrl-names = "default"; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/regmap/regmap.txt b/Documentation/devicetree/bindings/regmap/regmap.txt index b494f8b8ef72..e98a9652ccc8 100644 --- a/Documentation/devicetree/bindings/regmap/regmap.txt +++ b/Documentation/devicetree/bindings/regmap/regmap.txt @@ -5,15 +5,18 @@ Index Device Endianness properties --------------------------------------------------- 1 BE 'big-endian' 2 LE 'little-endian' +3 Native 'native-endian' For one device driver, which will run in different scenarios above on different SoCs using the devicetree, we need one way to simplify this. -Required properties: -- {big,little}-endian: these are boolean properties, if absent - meaning that the CPU and the Device are in the same endianness mode, - these properties are for register values and all the buffers only. +Optional properties: +- {big,little,native}-endian: these are boolean properties, if absent + then the implementation will choose a default based on the device + being controlled. These properties are for register values and all + the buffers only. Native endian means that the CPU and device have + the same endianness. Examples: Scenario 1 : CPU in LE mode & device in LE mode. diff --git a/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt b/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt new file mode 100644 index 000000000000..5c80a7779552 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt @@ -0,0 +1,80 @@ +Device-Tree bindings for regulators of Active-semi ACT8945A Multi-Function Device + +Required properties: + - compatible: "active-semi,act8945a", please refer to ../mfd/act8945a.txt. + +Optional properties: +- active-semi,vsel-high: Indicates if the VSEL pin is set to logic-high. + If this property is missing, assume the VSEL pin is set to logic-low. + +Optional input supply properties: + - vp1-supply: The input supply for REG_DCDC1 + - vp2-supply: The input supply for REG_DCDC2 + - vp3-supply: The input supply for REG_DCDC3 + - inl45-supply: The input supply for REG_LDO1 and REG_LDO2 + - inl67-supply: The input supply for REG_LDO3 and REG_LDO4 + +Any standard regulator properties can be used to configure the single regulator. + +The valid names for regulators are: + REG_DCDC1, REG_DCDC2, REG_DCDC3, REG_LDO1, REG_LDO2, REG_LDO3, REG_LDO4. + +Example: + pmic@5b { + compatible = "active-semi,act8945a"; + reg = <0x5b>; + status = "okay"; + + active-semi,vsel-high; + + regulators { + vdd_1v35_reg: REG_DCDC1 { + regulator-name = "VDD_1V35"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + vdd_1v2_reg: REG_DCDC2 { + regulator-name = "VDD_1V2"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + }; + + vdd_3v3_reg: REG_DCDC3 { + regulator-name = "VDD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_fuse_reg: REG_LDO1 { + regulator-name = "VDD_FUSE"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + vdd_3v3_lp_reg: REG_LDO2 { + regulator-name = "VDD_3V3_LP"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_led_reg: REG_LDO3 { + regulator-name = "VDD_LED"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_sdhc_1v8_reg: REG_LDO4 { + regulator-name = "VDD_SDHC_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/hisilicon,hi655x-regulator.txt b/Documentation/devicetree/bindings/regulator/hisilicon,hi655x-regulator.txt new file mode 100644 index 000000000000..14cfdc564159 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/hisilicon,hi655x-regulator.txt @@ -0,0 +1,29 @@ +Hisilicon Hi655x Voltage regulators + +Note: +The Hi655x regulator control is managed by Hi655x PMIC. +So the node of this regulator must be child node of Hi655x +PMIC node. + +The driver uses the regulator core framework, so please also +take the bindings of regulator.txt for reference. + +The valid names for regulators are: + +LDO2_2V8 LDO7_SDIO LDO10_2V85 LDO13_1V8 LDO14_2V8 +LDO15_1V8 LDO17_2V5 LDO19_3V0 LDO21_1V8 LDO22_1V2 + +Example: + pmic: pmic@f8000000 { + compatible = "hisilicon,hi655x-pmic"; + ... + regulators { + ldo2: LDO2@a21 { + regulator-name = "LDO2_2V8"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <3200000>; + regulator-enable-ramp-delay = <120>; + }; + ... + } + } diff --git a/Documentation/devicetree/bindings/regulator/lp872x.txt b/Documentation/devicetree/bindings/regulator/lp872x.txt index 78183182dad9..ca58a68ffdf1 100644 --- a/Documentation/devicetree/bindings/regulator/lp872x.txt +++ b/Documentation/devicetree/bindings/regulator/lp872x.txt @@ -28,6 +28,7 @@ Optional properties: - ti,dvs-gpio: GPIO specifier for external DVS pin control of LP872x devices. - ti,dvs-vsel: DVS selector. 0 = SEL_V1, 1 = SEL_V2. - ti,dvs-state: initial DVS pin state. 0 = DVS_LOW, 1 = DVS_HIGH. + - enable-gpios: GPIO specifier for EN pin control of LP872x devices. Sub nodes for regulator_init_data LP8720 has maximum 6 nodes. (child name: ldo1 ~ 5 and buck) diff --git a/Documentation/devicetree/bindings/regulator/max77802.txt b/Documentation/devicetree/bindings/regulator/max77802.txt index 09d796ed48be..879e98d3b9aa 100644 --- a/Documentation/devicetree/bindings/regulator/max77802.txt +++ b/Documentation/devicetree/bindings/regulator/max77802.txt @@ -60,7 +60,7 @@ The possible values for "regulator-initial-mode" and "regulator-mode" are: 1: Normal regulator voltage output mode. 3: Low Power which reduces the quiescent current down to only 1uA -The list of valid modes are defined in the dt-bindings/clock/maxim,max77802.h +The valid modes list is defined in the dt-bindings/regulator/maxim,max77802.h header and can be included by device tree source files. The standard "regulator-mode" property can only be used for regulators that diff --git a/Documentation/devicetree/bindings/regulator/regulator-max77620.txt b/Documentation/devicetree/bindings/regulator/regulator-max77620.txt new file mode 100644 index 000000000000..b3c8ca672024 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/regulator-max77620.txt @@ -0,0 +1,200 @@ +Regulator DT binding for MAX77620 Power management IC from Maxim Semiconductor. + +Device has multiple DCDC(sd[0-3] and LDOs(ldo[0-8]). The input supply +of these regulators are defined under parent device node. +Details of regulator properties are defined as child node under +sub-node "regulators" which is child node of device node. + +Please refer file <Documentation/devicetree/bindings/regulator/regulator.txt> +for common regulator bindings used by client. + +Following are properties of parent node related to regulators. + +Optional properties: +------------------- +The input supply of regulators are the optional properties on the +parent device node. The input supply of these regulators are provided +through following properties: +in-sd0-supply: Input supply for SD0, INA-SD0 or INB-SD0 pins. +in-sd1-supply: Input supply for SD1. +in-sd2-supply: Input supply for SD2. +in-sd3-supply: Input supply for SD3. +in-ldo0-1-supply: Input supply for LDO0 and LDO1. +in-ldo2-supply: Input supply for LDO2. +in-ldo3-5-supply: Input supply for LDO3 and LDO5 +in-ldo4-6-supply: Input supply for LDO4 and LDO6. +in-ldo7-8-supply: Input supply for LDO7 and LDO8. + +Optional sub nodes for regulators under "regulators" subnode: +------------------------------------------------------------ +The subnodes name is the name of regulator and it must be one of: + sd[0-3], ldo[0-8] + +Each sub-node should contain the constraints and initialization +information for that regulator. The definition for each of these +nodes is defined using the standard binding for regulators found at +<Documentation/devicetree/bindings/regulator/regulator.txt>. + +Theres are also additional properties for SD/LDOs. These additional properties +are required to configure FPS configuration parameters for SDs and LDOs. +Please refer <devicetree/bindings/mfd/max77620.txt> for more detail of Flexible +Power Sequence (FPS). +Following are additional properties: + +- maxim,active-fps-source: FPS source for the regulators to get + enabled/disabled when system is in + active state. Valid values are: + - MAX77620_FPS_SRC_0, + FPS source is FPS0. + - MAX77620_FPS_SRC_1, + FPS source is FPS1 + - MAX77620_FPS_SRC_2 and + FPS source is FPS2 + - MAX77620_FPS_SRC_NONE. + Regulator is not controlled + by FPS events and it gets + enabled/disabled by register + access. + Absence of this property will leave + the FPS configuration register for that + regulator to default configuration. + +- maxim,active-fps-power-up-slot: Sequencing event slot number on which + the regulator get enabled when + master FPS input event set to HIGH. + Valid values are 0 to 7. + This is applicable if FPS source is + selected as FPS0, FPS1 or FPS2. + +- maxim,active-fps-power-down-slot: Sequencing event slot number on which + the regulator get disabled when master + FPS input event set to LOW. + Valid values are 0 to 7. + This is applicable if FPS source is + selected as FPS0, FPS1 or FPS2. + +- maxim,suspend-fps-source: This is same as property + "maxim,active-fps-source" but value + get configured when system enters in + to suspend state. + +- maxim,suspend-fps-power-up-slot: This is same as property + "maxim,active-fps-power-up-slot" but + this value get configured into FPS + configuration register when system + enters into suspend. + This is applicable if suspend state + FPS source is selected as FPS0, FPS1 or + +- maxim,suspend-fps-power-down-slot: This is same as property + "maxim,active-fps-power-down-slot" but + this value get configured into FPS + configuration register when system + enters into suspend. + This is applicable if suspend state + FPS source is selected as FPS0, FPS1 or + FPS2. + +Example: +-------- +#include <dt-bindings/mfd/max77620.h> +... +max77620@3c { + in-ldo0-1-supply = <&max77620_sd2>; + in-ldo7-8-supply = <&max77620_sd2>; + regulators { + sd0 { + regulator-name = "vdd-core"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + maxim,active-fps-source = <MAX77620_FPS_SRC_1>; + }; + + sd1 { + regulator-name = "vddio-ddr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + maxim,active-fps-source = <MAX77620_FPS_SRC_0>; + }; + + sd2 { + regulator-name = "vdd-pre-reg"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + }; + + sd3 { + regulator-name = "vdd-1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo0 { + regulator-name = "avdd-sys"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo1 { + regulator-name = "vdd-pex"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + }; + + ldo2 { + regulator-name = "vddio-sdmmc3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + ldo3 { + regulator-name = "vdd-cam-hv"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo4 { + regulator-name = "vdd-rtc"; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo5 { + regulator-name = "avdd-ts-hv"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + ldo6 { + regulator-name = "vdd-ts"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo7 { + regulator-name = "vdd-gen-pll-edp"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo8 { + regulator-name = "vdd-hdmi-dp"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 1d112fc456aa..ecfc593cac15 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -44,6 +44,11 @@ Optional properties: any consumer request. - regulator-pull-down: Enable pull down resistor when the regulator is disabled. - regulator-over-current-protection: Enable over current protection. +- regulator-active-discharge: tristate, enable/disable active discharge of + regulators. The values are: + 0: Disable active discharge. + 1: Enable active discharge. + Absence of this property will leave configuration to default. Deprecated properties: - regulator-compatible: If a regulator chip contains multiple diff --git a/Documentation/devicetree/bindings/regulator/tps65217.txt b/Documentation/devicetree/bindings/regulator/tps65217.txt index d18109657da6..4f05d208c95c 100644 --- a/Documentation/devicetree/bindings/regulator/tps65217.txt +++ b/Documentation/devicetree/bindings/regulator/tps65217.txt @@ -26,11 +26,7 @@ Example: ti,pmic-shutdown-controller; regulators { - #address-cells = <1>; - #size-cells = <0>; - dcdc1_reg: dcdc1 { - reg = <0>; regulator-min-microvolt = <900000>; regulator-max-microvolt = <1800000>; regulator-boot-on; @@ -38,7 +34,6 @@ Example: }; dcdc2_reg: dcdc2 { - reg = <1>; regulator-min-microvolt = <900000>; regulator-max-microvolt = <3300000>; regulator-boot-on; @@ -46,7 +41,6 @@ Example: }; dcdc3_reg: dcc3 { - reg = <2>; regulator-min-microvolt = <900000>; regulator-max-microvolt = <1500000>; regulator-boot-on; @@ -54,7 +48,6 @@ Example: }; ldo1_reg: ldo1 { - reg = <3>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; regulator-boot-on; @@ -62,7 +55,6 @@ Example: }; ldo2_reg: ldo2 { - reg = <4>; regulator-min-microvolt = <900000>; regulator-max-microvolt = <3300000>; regulator-boot-on; @@ -70,7 +62,6 @@ Example: }; ldo3_reg: ldo3 { - reg = <5>; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-boot-on; @@ -78,7 +69,6 @@ Example: }; ldo4_reg: ldo4 { - reg = <6>; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-boot-on; diff --git a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt index ac2fcd6ff4b8..1068ffce9f91 100644 --- a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt @@ -14,6 +14,10 @@ Required properties: interrupt number is the rtc alarm interrupt and second interrupt number is the rtc tick interrupt. The number of cells representing a interrupt depends on the parent interrupt controller. +- clocks: Must contain a list of phandle and clock specifier for the rtc + and source clocks. +- clock-names: Must contain "rtc" and "rtc_src" entries sorted in the + same order as the clocks property. Example: @@ -21,4 +25,6 @@ Example: compatible = "samsung,s3c6410-rtc"; reg = <0x10070000 0x100>; interrupts = <44 0 45 0>; + clocks = <&clock CLK_RTC>, <&s2mps11_osc S2MPS11_CLK_AP>; + clock-names = "rtc", "rtc_src"; }; diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt index 35ae1fb3537f..ed94c217c98d 100644 --- a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt +++ b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt @@ -9,7 +9,7 @@ Optional properties: - fsl,uart-has-rtscts : Indicate the uart has rts and cts - fsl,irda-mode : Indicate the uart supports irda mode - fsl,dte-mode : Indicate the uart works in DTE mode. The uart works - is DCE mode by default. + in DCE mode by default. Note: Each uart controller should have an alias correctly numbered in "aliases" node. diff --git a/Documentation/devicetree/bindings/sound/cs4271.txt b/Documentation/devicetree/bindings/sound/cs4271.txt index e2cd1d7539e5..6e699ceabacd 100644 --- a/Documentation/devicetree/bindings/sound/cs4271.txt +++ b/Documentation/devicetree/bindings/sound/cs4271.txt @@ -33,12 +33,19 @@ Optional properties: Note that this is not needed in case the clocks are stable throughout the entire runtime of the codec. + - vd-supply: Digital power + - vl-supply: Logic power + - va-supply: Analog Power + Examples: codec_i2c: cs4271@10 { compatible = "cirrus,cs4271"; reg = <0x10>; reset-gpio = <&gpio 23 0>; + vd-supply = <&vdd_3v3_reg>; + vl-supply = <&vdd_3v3_reg>; + va-supply = <&vdd_3v3_reg>; }; codec_spi: cs4271@0 { diff --git a/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt b/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt index ce55c0a6f757..4da41bf1888e 100644 --- a/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt +++ b/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt @@ -30,6 +30,8 @@ The compatible list for this generic sound card currently: "fsl,imx-audio-sgtl5000" (compatible with Documentation/devicetree/bindings/sound/imx-audio-sgtl5000.txt) + "fsl,imx-audio-wm8960" + Required properties: - compatible : Contains one of entries in the compatible list. diff --git a/Documentation/devicetree/bindings/spi/adi,axi-spi-engine.txt b/Documentation/devicetree/bindings/spi/adi,axi-spi-engine.txt new file mode 100644 index 000000000000..8a18d71e6879 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/adi,axi-spi-engine.txt @@ -0,0 +1,31 @@ +Analog Devices AXI SPI Engine controller Device Tree Bindings + +Required properties: +- compatible : Must be "adi,axi-spi-engine-1.00.a"" +- reg : Physical base address and size of the register map. +- interrupts : Property with a value describing the interrupt + number. +- clock-names : List of input clock names - "s_axi_aclk", "spi_clk" +- clocks : Clock phandles and specifiers (See clock bindings for + details on clock-names and clocks). +- #address-cells : Must be <1> +- #size-cells : Must be <0> + +Optional subnodes: + Subnodes are use to represent the SPI slave devices connected to the SPI + master. They follow the generic SPI bindings as outlined in spi-bus.txt. + +Example: + + spi@@44a00000 { + compatible = "adi,axi-spi-engine-1.00.a"; + reg = <0x44a00000 0x1000>; + interrupts = <0 56 4>; + clocks = <&clkc 15 &clkc 15>; + clock-names = "s_axi_aclk", "spi_clk"; + + #address-cells = <1>; + #size-cells = <0>; + + /* SPI devices */ + }; diff --git a/Documentation/devicetree/bindings/spi/icpdas-lp8841-spi-rtc.txt b/Documentation/devicetree/bindings/spi/icpdas-lp8841-spi-rtc.txt new file mode 100644 index 000000000000..852b651f3bc5 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/icpdas-lp8841-spi-rtc.txt @@ -0,0 +1,54 @@ +* ICP DAS LP-8841 SPI Controller for RTC + +ICP DAS LP-8841 contains a DS-1302 RTC. RTC is connected to an IO +memory register, which acts as an SPI master device. + +The device uses the standard MicroWire half-duplex transfer timing. +Master output is set on low clock and sensed by the RTC on the rising +edge. Master input is set by the RTC on the trailing edge and is sensed +by the master on low clock. + +Required properties: + +- #address-cells: should be 1 + +- #size-cells: should be 0 + +- compatible: should be "icpdas,lp8841-spi-rtc" + +- reg: should provide IO memory address + +Requirements to SPI slave nodes: + +- There can be only one slave device. + +- The spi slave node should claim the following flags which are + required by the spi controller. + + - spi-3wire: The master itself has only 3 wire. It cannor work in + full duplex mode. + + - spi-cs-high: DS-1302 has active high chip select line. The master + doesn't support active low. + + - spi-lsb-first: DS-1302 requires least significant bit first + transfers. The master only support this type of bit ordering. + + +Example: + +spi@901c { + #address-cells = <1>; + #size-cells = <0>; + compatible = "icpdas,lp8841-spi-rtc"; + reg = <0x901c 0x1>; + + rtc@0 { + compatible = "maxim,ds1302"; + reg = <0>; + spi-max-frequency = <500000>; + spi-3wire; + spi-lsb-first; + spi-cs-high; + }; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-rockchip.txt b/Documentation/devicetree/bindings/spi/spi-rockchip.txt index 0c491bda4c65..1b14d69d8903 100644 --- a/Documentation/devicetree/bindings/spi/spi-rockchip.txt +++ b/Documentation/devicetree/bindings/spi/spi-rockchip.txt @@ -9,6 +9,7 @@ Required Properties: "rockchip,rk3066-spi" for rk3066. "rockchip,rk3188-spi", "rockchip,rk3066-spi" for rk3188. "rockchip,rk3288-spi", "rockchip,rk3066-spi" for rk3288. + "rockchip,rk3399-spi", "rockchip,rk3066-spi" for rk3399. - reg: physical base address of the controller and length of memory mapped region. - interrupts: The interrupt number to the cpu. The interrupt specifier format diff --git a/Documentation/devicetree/bindings/spi/spi-xilinx.txt b/Documentation/devicetree/bindings/spi/spi-xilinx.txt new file mode 100644 index 000000000000..c7b7856bd528 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-xilinx.txt @@ -0,0 +1,22 @@ +Xilinx SPI controller Device Tree Bindings +------------------------------------------------- + +Required properties: +- compatible : Should be "xlnx,xps-spi-2.00.a" or "xlnx,xps-spi-2.00.b" +- reg : Physical base address and size of SPI registers map. +- interrupts : Property with a value describing the interrupt + number. +- interrupt-parent : Must be core interrupt controller + +Optional properties: +- xlnx,num-ss-bits : Number of chip selects used. + +Example: + axi_quad_spi@41e00000 { + compatible = "xlnx,xps-spi-2.00.a"; + interrupt-parent = <&intc>; + interrupts = <0 31 1>; + reg = <0x41e00000 0x10000>; + xlnx,num-ss-bits = <0x1>; + }; + diff --git a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt index 332e625f6ed0..e5ee3f159893 100644 --- a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt @@ -1,8 +1,9 @@ * Renesas R-Car Thermal Required properties: -- compatible : "renesas,thermal-<soctype>", "renesas,rcar-thermal" - as fallback. +- compatible : "renesas,thermal-<soctype>", + "renesas,rcar-gen2-thermal" (with thermal-zone) or + "renesas,rcar-thermal" (without thermal-zone) as fallback. Examples with soctypes are: - "renesas,thermal-r8a73a4" (R-Mobile APE6) - "renesas,thermal-r8a7779" (R-Car H1) @@ -36,3 +37,35 @@ thermal@e61f0000 { 0xe61f0300 0x38>; interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>; }; + +Example (with thermal-zone): + +thermal-zones { + cpu_thermal: cpu-thermal { + polling-delay-passive = <1000>; + polling-delay = <5000>; + + thermal-sensors = <&thermal>; + + trips { + cpu-crit { + temperature = <115000>; + hysteresis = <0>; + type = "critical"; + }; + }; + cooling-maps { + }; + }; +}; + +thermal: thermal@e61f0000 { + compatible = "renesas,thermal-r8a7790", + "renesas,rcar-gen2-thermal", + "renesas,rcar-thermal"; + reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>; + interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp5_clks R8A7790_CLK_THERMAL>; + power-domains = <&cpg_clocks>; + #thermal-sensor-cells = <0>; +}; diff --git a/Documentation/filesystems/efivarfs.txt b/Documentation/filesystems/efivarfs.txt index c477af086e65..686a64bba775 100644 --- a/Documentation/filesystems/efivarfs.txt +++ b/Documentation/filesystems/efivarfs.txt @@ -14,3 +14,10 @@ filesystem. efivarfs is typically mounted like this, mount -t efivarfs none /sys/firmware/efi/efivars + +Due to the presence of numerous firmware bugs where removing non-standard +UEFI variables causes the system firmware to fail to POST, efivarfs +files that are not well-known standardized variables are created +as immutable files. This doesn't prevent removal - "chattr -i" will work - +but it does prevent this kind of failure from being accomplished +accidentally. diff --git a/Documentation/filesystems/proc.txt b/Documentation/filesystems/proc.txt index fde9fd06fa98..843b045b4069 100644 --- a/Documentation/filesystems/proc.txt +++ b/Documentation/filesystems/proc.txt @@ -240,8 +240,8 @@ Table 1-2: Contents of the status files (as of 4.1) RssFile size of resident file mappings RssShmem size of resident shmem memory (includes SysV shm, mapping of tmpfs and shared anonymous mappings) - VmData size of data, stack, and text segments - VmStk size of data, stack, and text segments + VmData size of private data segments + VmStk size of stack segments VmExe size of text segment VmLib size of shared library code VmPTE size of page table entries @@ -356,7 +356,7 @@ address perms offset dev inode pathname a7cb1000-a7cb2000 ---p 00000000 00:00 0 a7cb2000-a7eb2000 rw-p 00000000 00:00 0 a7eb2000-a7eb3000 ---p 00000000 00:00 0 -a7eb3000-a7ed5000 rw-p 00000000 00:00 0 [stack:1001] +a7eb3000-a7ed5000 rw-p 00000000 00:00 0 a7ed5000-a8008000 r-xp 00000000 03:00 4222 /lib/libc.so.6 a8008000-a800a000 r--p 00133000 03:00 4222 /lib/libc.so.6 a800a000-a800b000 rw-p 00135000 03:00 4222 /lib/libc.so.6 @@ -388,7 +388,6 @@ is not associated with a file: [heap] = the heap of the program [stack] = the stack of the main process - [stack:1001] = the stack of the thread with tid 1001 [vdso] = the "virtual dynamic shared object", the kernel system call handler @@ -396,10 +395,8 @@ is not associated with a file: The /proc/PID/task/TID/maps is a view of the virtual memory from the viewpoint of the individual tasks of a process. In this file you will see a mapping marked -as [stack] if that task sees it as a stack. This is a key difference from the -content of /proc/PID/maps, where you will see all mappings that are being used -as stack by all of those tasks. Hence, for the example above, the task-level -map, i.e. /proc/PID/task/TID/maps for thread 1001 will look like this: +as [stack] if that task sees it as a stack. Hence, for the example above, the +task-level map, i.e. /proc/PID/task/TID/maps for thread 1001 will look like this: 08048000-08049000 r-xp 00000000 03:00 8312 /opt/test 08049000-0804a000 rw-p 00001000 03:00 8312 /opt/test diff --git a/Documentation/hwmon/adm1275 b/Documentation/hwmon/adm1275 index d697229e3c18..791bc0bd91e6 100644 --- a/Documentation/hwmon/adm1275 +++ b/Documentation/hwmon/adm1275 @@ -14,6 +14,10 @@ Supported chips: Prefix: 'adm1276' Addresses scanned: - Datasheet: www.analog.com/static/imported-files/data_sheets/ADM1276.pdf + * Analog Devices ADM1278 + Prefix: 'adm1278' + Addresses scanned: - + Datasheet: www.analog.com/static/imported-files/data_sheets/ADM1278.pdf * Analog Devices ADM1293/ADM1294 Prefix: 'adm1293', 'adm1294' Addresses scanned: - @@ -25,13 +29,15 @@ Author: Guenter Roeck <linux@roeck-us.net> Description ----------- -This driver supports hardware montoring for Analog Devices ADM1075, ADM1275, -ADM1276, ADM1293, and ADM1294 Hot-Swap Controller and Digital Power Monitors. +This driver supports hardware monitoring for Analog Devices ADM1075, ADM1275, +ADM1276, ADM1278, ADM1293, and ADM1294 Hot-Swap Controller and Digital +Power Monitors. -ADM1075, ADM1275, ADM1276, ADM1293, and ADM1294 are hot-swap controllers that -allow a circuit board to be removed from or inserted into a live backplane. -They also feature current and voltage readback via an integrated 12 -bit analog-to-digital converter (ADC), accessed using a PMBus interface. +ADM1075, ADM1275, ADM1276, ADM1278, ADM1293, and ADM1294 are hot-swap +controllers that allow a circuit board to be removed from or inserted into +a live backplane. They also feature current and voltage readback via an +integrated 12 bit analog-to-digital converter (ADC), accessed using a +PMBus interface. The driver is a client driver to the core PMBus driver. Please see Documentation/hwmon/pmbus for details on PMBus client drivers. @@ -96,3 +102,14 @@ power1_reset_history Write any value to reset history. Power attributes are supported on ADM1075, ADM1276, ADM1293, and ADM1294. + +temp1_input Chip temperature. + Temperature attributes are only available on ADM1278. +temp1_max Maximum chip temperature. +temp1_max_alarm Temperature alarm. +temp1_crit Critical chip temperature. +temp1_crit_alarm Critical temperature high alarm. +temp1_highest Highest observed temperature. +temp1_reset_history Write any value to reset history. + + Temperature attributes are supported on ADM1278. diff --git a/Documentation/hwmon/lm25066 b/Documentation/hwmon/lm25066 index b34c3de5c1bc..2cb20ebb234d 100644 --- a/Documentation/hwmon/lm25066 +++ b/Documentation/hwmon/lm25066 @@ -36,7 +36,7 @@ Author: Guenter Roeck <linux@roeck-us.net> Description ----------- -This driver supports hardware montoring for National Semiconductor / TI LM25056, +This driver supports hardware monitoring for National Semiconductor / TI LM25056, LM25063, LM25066, LM5064, and LM5066 Power Management, Monitoring, Control, and Protection ICs. diff --git a/Documentation/hwmon/ltc2990 b/Documentation/hwmon/ltc2990 new file mode 100644 index 000000000000..c25211e90bdc --- /dev/null +++ b/Documentation/hwmon/ltc2990 @@ -0,0 +1,43 @@ +Kernel driver ltc2990 +===================== + +Supported chips: + * Linear Technology LTC2990 + Prefix: 'ltc2990' + Addresses scanned: - + Datasheet: http://www.linear.com/product/ltc2990 + +Author: Mike Looijmans <mike.looijmans@topic.nl> + + +Description +----------- + +LTC2990 is a Quad I2C Voltage, Current and Temperature Monitor. +The chip's inputs can measure 4 voltages, or two inputs together (1+2 and 3+4) +can be combined to measure a differential voltage, which is typically used to +measure current through a series resistor, or a temperature. + +This driver currently uses the 2x differential mode only. In order to support +other modes, the driver will need to be expanded. + + +Usage Notes +----------- + +This driver does not probe for PMBus devices. You will have to instantiate +devices explicitly. + + +Sysfs attributes +---------------- + +The "curr*_input" measurements actually report the voltage drop across the +input pins in microvolts. This is equivalent to the current through a 1mOhm +sense resistor. Divide the reported value by the actual sense resistor value +in mOhm to get the actual value. + +in0_input Voltage at Vcc pin in millivolt (range 2.5V to 5V) +temp1_input Internal chip temperature in millidegrees Celcius +curr1_input Current in mA across v1-v2 assuming a 1mOhm sense resistor. +curr2_input Current in mA across v3-v4 assuming a 1mOhm sense resistor. diff --git a/Documentation/hwmon/max16064 b/Documentation/hwmon/max16064 index d59cc7829bec..265370f5cb82 100644 --- a/Documentation/hwmon/max16064 +++ b/Documentation/hwmon/max16064 @@ -13,7 +13,7 @@ Author: Guenter Roeck <linux@roeck-us.net> Description ----------- -This driver supports hardware montoring for Maxim MAX16064 Quad Power-Supply +This driver supports hardware monitoring for Maxim MAX16064 Quad Power-Supply Controller with Active-Voltage Output Control and PMBus Interface. The driver is a client driver to the core PMBus driver. diff --git a/Documentation/hwmon/max34440 b/Documentation/hwmon/max34440 index 37cbf472a19d..f5b1fcaa9e4e 100644 --- a/Documentation/hwmon/max34440 +++ b/Documentation/hwmon/max34440 @@ -33,7 +33,7 @@ Author: Guenter Roeck <linux@roeck-us.net> Description ----------- -This driver supports hardware montoring for Maxim MAX34440 PMBus 6-Channel +This driver supports hardware monitoring for Maxim MAX34440 PMBus 6-Channel Power-Supply Manager, MAX34441 PMBus 5-Channel Power-Supply Manager and Intelligent Fan Controller, and MAX34446 PMBus Power-Supply Data Logger. It also supports the MAX34460 and MAX34461 PMBus Voltage Monitor & Sequencers. diff --git a/Documentation/hwmon/max8688 b/Documentation/hwmon/max8688 index e78078638b91..ca233bec7a8a 100644 --- a/Documentation/hwmon/max8688 +++ b/Documentation/hwmon/max8688 @@ -13,7 +13,7 @@ Author: Guenter Roeck <linux@roeck-us.net> Description ----------- -This driver supports hardware montoring for Maxim MAX8688 Digital Power-Supply +This driver supports hardware monitoring for Maxim MAX8688 Digital Power-Supply Controller/Monitor with PMBus Interface. The driver is a client driver to the core PMBus driver. Please see diff --git a/Documentation/hwmon/nsa320 b/Documentation/hwmon/nsa320 new file mode 100644 index 000000000000..fdbd6947799b --- /dev/null +++ b/Documentation/hwmon/nsa320 @@ -0,0 +1,53 @@ +Kernel driver nsa320_hwmon +========================== + +Supported chips: + * Holtek HT46R065 microcontroller with onboard firmware that configures + it to act as a hardware monitor. + Prefix: 'nsa320' + Addresses scanned: none + Datasheet: Not available, driver was reverse engineered based upon the + Zyxel kernel source + +Author: + Adam Baker <linux@baker-net.org.uk> + +Description +----------- + +This chip is known to be used in the Zyxel NSA320 and NSA325 NAS Units and +also in some variants of the NSA310 but the driver has only been tested +on the NSA320. In all of these devices it is connected to the same 3 GPIO +lines which are used to provide chip select, clock and data lines. The +interface behaves similarly to SPI but at much lower speeds than are normally +used for SPI. + +Following each chip select pulse the chip will generate a single 32 bit word +that contains 0x55 as a marker to indicate that data is being read correctly, +followed by an 8 bit fan speed in 100s of RPM and a 16 bit temperature in +tenths of a degree. + + +sysfs-Interface +--------------- + +temp1_input - temperature input +fan1_input - fan speed + +Notes +----- + +The access timings used in the driver are the same as used in the Zyxel +provided kernel. Testing has shown that if the delay between chip select and +the first clock pulse is reduced from 100 ms to just under 10ms then the chip +will not produce any output. If the duration of either phase of the clock +is reduced from 100 us to less than 15 us then data pulses are likely to be +read twice corrupting the output. The above analysis is based upon a sample +of one unit but suggests that the Zyxel provided delay values include a +reasonable tolerance. + +The driver incorporates a limit that it will not check for updated values +faster than once a second. This is because the hardware takes a relatively long +time to read the data from the device and when it does it reads both temp and +fan speed. As the most likely case for two accesses in quick succession is +to read both of these values avoiding a second read delay is desirable. diff --git a/Documentation/hwmon/ntc_thermistor b/Documentation/hwmon/ntc_thermistor index 1d4cc847c6fe..8b9ff23edc32 100644 --- a/Documentation/hwmon/ntc_thermistor +++ b/Documentation/hwmon/ntc_thermistor @@ -3,9 +3,9 @@ Kernel driver ntc_thermistor Supported thermistors from Murata: * Murata NTC Thermistors NCP15WB473, NCP18WB473, NCP21WB473, NCP03WB473, - NCP15WL333, NCP03WF104 + NCP15WL333, NCP03WF104, NCP15XH103 Prefixes: 'ncp15wb473', 'ncp18wb473', 'ncp21wb473', 'ncp03wb473', - 'ncp15wl333', 'ncp03wf104' + 'ncp15wl333', 'ncp03wf104', 'ncp15xh103' Datasheet: Publicly available at Murata Supported thermistors from EPCOS: diff --git a/Documentation/hwmon/pmbus b/Documentation/hwmon/pmbus index b397675e876d..dfd9c65996c0 100644 --- a/Documentation/hwmon/pmbus +++ b/Documentation/hwmon/pmbus @@ -43,7 +43,7 @@ Author: Guenter Roeck <linux@roeck-us.net> Description ----------- -This driver supports hardware montoring for various PMBus compliant devices. +This driver supports hardware monitoring for various PMBus compliant devices. It supports voltage, current, power, and temperature sensors as supported by the device. diff --git a/Documentation/hwmon/zl6100 b/Documentation/hwmon/zl6100 index 33908a4d68ff..477a94b131ae 100644 --- a/Documentation/hwmon/zl6100 +++ b/Documentation/hwmon/zl6100 @@ -60,7 +60,7 @@ Author: Guenter Roeck <linux@roeck-us.net> Description ----------- -This driver supports hardware montoring for Intersil / Zilker Labs ZL6100 and +This driver supports hardware monitoring for Intersil / Zilker Labs ZL6100 and compatible digital DC-DC controllers. The driver is a client driver to the core PMBus driver. Please see diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 87d40a72f6a1..4d9ca7d92a20 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -666,7 +666,7 @@ bytes respectively. Such letter suffixes can also be entirely omitted. clearcpuid=BITNUM [X86] Disable CPUID feature X for the kernel. See - arch/x86/include/asm/cpufeature.h for the valid bit + arch/x86/include/asm/cpufeatures.h for the valid bit numbers. Note the Linux specific bits are not necessarily stable over kernel options, but the vendor specific ones should be. @@ -1496,6 +1496,11 @@ bytes respectively. Such letter suffixes can also be entirely omitted. could change it dynamically, usually by /sys/module/printk/parameters/ignore_loglevel. + ignore_rlimit_data + Ignore RLIMIT_DATA setting for data mappings, + print warning at first misuse. Can be changed via + /sys/module/kernel/parameters/ignore_rlimit_data. + ihash_entries= [KNL] Set number of hash buckets for inode cache. @@ -1682,6 +1687,15 @@ bytes respectively. Such letter suffixes can also be entirely omitted. ip= [IP_PNP] See Documentation/filesystems/nfs/nfsroot.txt. + irqaffinity= [SMP] Set the default irq affinity mask + Format: + <cpu number>,...,<cpu number> + or + <cpu number>-<cpu number> + (must be a positive range in ascending order) + or a mixture + <cpu number>,...,<cpu number>-<cpu number> + irqfixup [HW] When an interrupt is not handled search all handlers for it. Intended to get systems with badly broken @@ -2561,6 +2575,8 @@ bytes respectively. Such letter suffixes can also be entirely omitted. nointroute [IA-64] + noinvpcid [X86] Disable the INVPCID cpu feature. + nojitter [IA-64] Disables jitter checking for ITC timers. no-kvmclock [X86,KVM] Disable paravirtualized KVM clock driver @@ -3486,6 +3502,10 @@ bytes respectively. Such letter suffixes can also be entirely omitted. ro [KNL] Mount root device read-only on boot + rodata= [KNL] + on Mark read-only kernel memory as read-only (default). + off Leave read-only kernel memory writable for debugging. + root= [KNL] Root filesystem See name_to_dev_t comment in init/do_mounts.c. @@ -3523,6 +3543,11 @@ bytes respectively. Such letter suffixes can also be entirely omitted. sched_debug [KNL] Enables verbose scheduler debug messages. + schedstats= [KNL,X86] Enable or disable scheduled statistics. + Allowed values are enable and disable. This feature + incurs a small amount of overhead in the scheduler + but is useful for debugging and performance tuning. + skew_tick= [KNL] Offset the periodic timer tick per cpu to mitigate xtime_lock contention on larger systems, and/or RCU lock contention on all systems with CONFIG_MAXSMP set. @@ -4230,6 +4255,17 @@ bytes respectively. Such letter suffixes can also be entirely omitted. The default value of this parameter is determined by the config option CONFIG_WQ_POWER_EFFICIENT_DEFAULT. + workqueue.debug_force_rr_cpu + Workqueue used to implicitly guarantee that work + items queued without explicit CPU specified are put + on the local CPU. This guarantee is no longer true + and while local CPU is still preferred work items + may be put on foreign CPUs. This debug option + forces round-robin CPU selection to flush out + usages which depend on the now broken guarantee. + When enabled, memory and cache locality will be + impacted. + x2apic_phys [X86-64,APIC] Use x2apic physical mode instead of default x2apic cluster mode on platforms supporting x2apic. diff --git a/Documentation/networking/ip-sysctl.txt b/Documentation/networking/ip-sysctl.txt index ceb44a095a27..73b36d7c7b0d 100644 --- a/Documentation/networking/ip-sysctl.txt +++ b/Documentation/networking/ip-sysctl.txt @@ -594,7 +594,7 @@ tcp_fastopen - INTEGER tcp_syn_retries - INTEGER Number of times initial SYNs for an active TCP connection attempt - will be retransmitted. Should not be higher than 255. Default value + will be retransmitted. Should not be higher than 127. Default value is 6, which corresponds to 63seconds till the last retransmission with the current initial RTO of 1second. With this the final timeout for an active TCP connection attempt will happen after 127seconds. diff --git a/Documentation/ptp/testptp.c b/Documentation/ptp/testptp.c index 6c6247aaa7b9..d99012f41602 100644 --- a/Documentation/ptp/testptp.c +++ b/Documentation/ptp/testptp.c @@ -277,13 +277,15 @@ int main(int argc, char *argv[]) " %d external time stamp channels\n" " %d programmable periodic signals\n" " %d pulse per second\n" - " %d programmable pins\n", + " %d programmable pins\n" + " %d cross timestamping\n", caps.max_adj, caps.n_alarm, caps.n_ext_ts, caps.n_per_out, caps.pps, - caps.n_pins); + caps.n_pins, + caps.cross_timestamping); } } diff --git a/Documentation/sysctl/kernel.txt b/Documentation/sysctl/kernel.txt index a93b414672a7..f4444c94ff28 100644 --- a/Documentation/sysctl/kernel.txt +++ b/Documentation/sysctl/kernel.txt @@ -58,6 +58,8 @@ show up in /proc/sys/kernel: - panic_on_stackoverflow - panic_on_unrecovered_nmi - panic_on_warn +- perf_cpu_time_max_percent +- perf_event_paranoid - pid_max - powersave-nap [ PPC only ] - printk @@ -639,6 +641,17 @@ allowed to execute. ============================================================== +perf_event_paranoid: + +Controls use of the performance events system by unprivileged +users (without CAP_SYS_ADMIN). The default value is 1. + + -1: Allow use of (almost) all events by all users +>=0: Disallow raw tracepoint access by users without CAP_IOC_LOCK +>=1: Disallow CPU event access by users without CAP_SYS_ADMIN +>=2: Disallow kernel profiling by users without CAP_SYS_ADMIN + +============================================================== pid_max: @@ -760,6 +773,14 @@ rtsig-nr shows the number of RT signals currently queued. ============================================================== +sched_schedstats: + +Enables/disables scheduler statistics. Enabling this feature +incurs a small amount of overhead in the scheduler but is +useful for debugging and performance tuning. + +============================================================== + sg-big-buff: This file shows the size of the generic SCSI (sg) buffer. diff --git a/Documentation/timers/hpet.txt b/Documentation/timers/hpet.txt index 767392ffd31e..a484d2c109d7 100644 --- a/Documentation/timers/hpet.txt +++ b/Documentation/timers/hpet.txt @@ -1,9 +1,7 @@ High Precision Event Timer Driver for Linux The High Precision Event Timer (HPET) hardware follows a specification -by Intel and Microsoft which can be found at - - http://www.intel.com/hardwaredesign/hpetspec_1.pdf +by Intel and Microsoft, revision 1. Each HPET has one fixed-rate counter (at 10+ MHz, hence "High Precision") and up to 32 comparators. Normally three or more comparators are provided, diff --git a/Documentation/virtual/kvm/api.txt b/Documentation/virtual/kvm/api.txt index 053f613fc9a9..07e4cdf02407 100644 --- a/Documentation/virtual/kvm/api.txt +++ b/Documentation/virtual/kvm/api.txt @@ -3025,7 +3025,7 @@ len must be a multiple of sizeof(struct kvm_s390_irq). It must be > 0 and it must not exceed (max_vcpus + 32) * sizeof(struct kvm_s390_irq), which is the maximum number of possibly pending cpu-local interrupts. -4.90 KVM_SMI +4.96 KVM_SMI Capability: KVM_CAP_X86_SMM Architectures: x86 diff --git a/Documentation/virtual/kvm/mmu.txt b/Documentation/virtual/kvm/mmu.txt index daf9c0f742d2..c81731096a43 100644 --- a/Documentation/virtual/kvm/mmu.txt +++ b/Documentation/virtual/kvm/mmu.txt @@ -358,7 +358,8 @@ In the first case there are two additional complications: - if CR4.SMEP is enabled: since we've turned the page into a kernel page, the kernel may now execute it. We handle this by also setting spte.nx. If we get a user fetch or read fault, we'll change spte.u=1 and - spte.nx=gpte.nx back. + spte.nx=gpte.nx back. For this to work, KVM forces EFER.NX to 1 when + shadow paging is in use. - if CR4.SMAP is disabled: since the page has been changed to a kernel page, it can not be reused when CR4.SMAP is enabled. We set CR4.SMAP && !CR0.WP into shadow page's role to avoid this case. Note, diff --git a/Documentation/watchdog/watchdog-parameters.txt b/Documentation/watchdog/watchdog-parameters.txt index 9f9ec9f76039..4e4b6f10d841 100644 --- a/Documentation/watchdog/watchdog-parameters.txt +++ b/Documentation/watchdog/watchdog-parameters.txt @@ -400,3 +400,7 @@ wm8350_wdt: nowayout: Watchdog cannot be stopped once started (default=kernel config parameter) ------------------------------------------------- +sun4v_wdt: +timeout_ms: Watchdog timeout in milliseconds 1..180000, default=60000) +nowayout: Watchdog cannot be stopped once started +------------------------------------------------- diff --git a/Documentation/x86/early-microcode.txt b/Documentation/x86/early-microcode.txt index d62bea6796da..c956d99cf1de 100644 --- a/Documentation/x86/early-microcode.txt +++ b/Documentation/x86/early-microcode.txt @@ -40,3 +40,28 @@ cp ../microcode.bin kernel/x86/microcode/GenuineIntel.bin (or AuthenticAMD.bin) find . | cpio -o -H newc >../ucode.cpio cd .. cat ucode.cpio /boot/initrd-3.5.0.img >/boot/initrd-3.5.0.ucode.img + +Builtin microcode +================= + +We can also load builtin microcode supplied through the regular firmware +builtin method CONFIG_FIRMWARE_IN_KERNEL. Here's an example: + +CONFIG_FIRMWARE_IN_KERNEL=y +CONFIG_EXTRA_FIRMWARE="intel-ucode/06-3a-09 amd-ucode/microcode_amd_fam15h.bin" +CONFIG_EXTRA_FIRMWARE_DIR="/lib/firmware" + +This basically means, you have the following tree structure locally: + +/lib/firmware/ +|-- amd-ucode +... +| |-- microcode_amd_fam15h.bin +... +|-- intel-ucode +... +| |-- 06-3a-09 +... + +so that the build system can find those files and integrate them into +the final kernel image. The early loader finds them and applies them. diff --git a/Documentation/x86/exception-tables.txt b/Documentation/x86/exception-tables.txt index 32901aa36f0a..e396bcd8d830 100644 --- a/Documentation/x86/exception-tables.txt +++ b/Documentation/x86/exception-tables.txt @@ -290,3 +290,38 @@ Due to the way that the exception table is built and needs to be ordered, only use exceptions for code in the .text section. Any other section will cause the exception table to not be sorted correctly, and the exceptions will fail. + +Things changed when 64-bit support was added to x86 Linux. Rather than +double the size of the exception table by expanding the two entries +from 32-bits to 64 bits, a clever trick was used to store addresses +as relative offsets from the table itself. The assembly code changed +from: + .long 1b,3b +to: + .long (from) - . + .long (to) - . + +and the C-code that uses these values converts back to absolute addresses +like this: + + ex_insn_addr(const struct exception_table_entry *x) + { + return (unsigned long)&x->insn + x->insn; + } + +In v4.6 the exception table entry was expanded with a new field "handler". +This is also 32-bits wide and contains a third relative function +pointer which points to one of: + +1) int ex_handler_default(const struct exception_table_entry *fixup) + This is legacy case that just jumps to the fixup code +2) int ex_handler_fault(const struct exception_table_entry *fixup) + This case provides the fault number of the trap that occurred at + entry->insn. It is used to distinguish page faults from machine + check. +3) int ex_handler_ext(const struct exception_table_entry *fixup) + This case is used for uaccess_err ... we need to set a flag + in the task structure. Before the handler functions existed this + case was handled by adding a large offset to the fixup to tag + it as special. +More functions can easily be added. diff --git a/Documentation/x86/x86_64/boot-options.txt b/Documentation/x86/x86_64/boot-options.txt index 68ed3114c363..0965a71f9942 100644 --- a/Documentation/x86/x86_64/boot-options.txt +++ b/Documentation/x86/x86_64/boot-options.txt @@ -60,6 +60,8 @@ Machine check threshold to 1. Enabling this may make memory predictive failure analysis less effective if the bios sets thresholds for memory errors since we will not see details for all errors. + mce=recovery + Force-enable recoverable machine check code paths nomce (for compatibility with i386): same as mce=off |