diff options
Diffstat (limited to 'Documentation')
31 files changed, 414 insertions, 145 deletions
diff --git a/Documentation/ABI/testing/sysfs-class-mtd b/Documentation/ABI/testing/sysfs-class-mtd index db1ad7e34fc3..938ef71e2035 100644 --- a/Documentation/ABI/testing/sysfs-class-mtd +++ b/Documentation/ABI/testing/sysfs-class-mtd @@ -142,13 +142,14 @@ KernelVersion: 3.4 Contact: linux-mtd@lists.infradead.org Description: This allows the user to examine and adjust the criteria by which - mtd returns -EUCLEAN from mtd_read(). If the maximum number of - bit errors that were corrected on any single region comprising - an ecc step (as reported by the driver) equals or exceeds this - value, -EUCLEAN is returned. Otherwise, absent an error, 0 is - returned. Higher layers (e.g., UBI) use this return code as an - indication that an erase block may be degrading and should be - scrutinized as a candidate for being marked as bad. + mtd returns -EUCLEAN from mtd_read() and mtd_read_oob(). If the + maximum number of bit errors that were corrected on any single + region comprising an ecc step (as reported by the driver) equals + or exceeds this value, -EUCLEAN is returned. Otherwise, absent + an error, 0 is returned. Higher layers (e.g., UBI) use this + return code as an indication that an erase block may be + degrading and should be scrutinized as a candidate for being + marked as bad. The initial value may be specified by the flash device driver. If not, then the default value is ecc_strength. @@ -167,7 +168,7 @@ Description: block degradation, but high enough to avoid the consequences of a persistent return value of -EUCLEAN on devices where sticky bitflips occur. Note that if bitflip_threshold exceeds - ecc_strength, -EUCLEAN is never returned by mtd_read(). + ecc_strength, -EUCLEAN is never returned by the read operations. Conversely, if bitflip_threshold is zero, -EUCLEAN is always returned, absent a hard error. diff --git a/Documentation/ABI/testing/sysfs-power b/Documentation/ABI/testing/sysfs-power index 31725ffeeb3a..217772615d02 100644 --- a/Documentation/ABI/testing/sysfs-power +++ b/Documentation/ABI/testing/sysfs-power @@ -231,3 +231,16 @@ Description: Reads from this file return a string consisting of the names of wakeup sources created with the help of /sys/power/wake_lock that are inactive at the moment, separated with spaces. + +What: /sys/power/pm_print_times +Date: May 2012 +Contact: Sameer Nanda <snanda@chromium.org> +Description: + The /sys/power/pm_print_times file allows user space to + control whether the time taken by devices to suspend and + resume is printed. These prints are useful for hunting down + devices that take too long to suspend or resume. + + Writing a "1" enables this printing while writing a "0" + disables it. The default value is "0". Reading from this file + will display the current value. diff --git a/Documentation/DocBook/media/v4l/controls.xml b/Documentation/DocBook/media/v4l/controls.xml index 676bc46f9c52..cda0dfb6769a 100644 --- a/Documentation/DocBook/media/v4l/controls.xml +++ b/Documentation/DocBook/media/v4l/controls.xml @@ -3988,7 +3988,7 @@ interface and may change in the future.</para> from RGB to Y'CbCr color space. </entry> </row> - <row id = "v4l2-jpeg-chroma-subsampling"> + <row> <entrytbl spanname="descr" cols="2"> <tbody valign="top"> <row> diff --git a/Documentation/DocBook/media/v4l/vidioc-g-ext-ctrls.xml b/Documentation/DocBook/media/v4l/vidioc-g-ext-ctrls.xml index e3d5afcdafbb..0a4b90fcf2da 100644 --- a/Documentation/DocBook/media/v4l/vidioc-g-ext-ctrls.xml +++ b/Documentation/DocBook/media/v4l/vidioc-g-ext-ctrls.xml @@ -284,13 +284,6 @@ These controls are described in <xref processing controls. These controls are described in <xref linkend="image-process-controls" />.</entry> </row> - <row> - <entry><constant>V4L2_CTRL_CLASS_JPEG</constant></entry> - <entry>0x9d0000</entry> - <entry>The class containing JPEG compression controls. -These controls are described in <xref - linkend="jpeg-controls" />.</entry> - </row> </tbody> </tgroup> </table> diff --git a/Documentation/RCU/checklist.txt b/Documentation/RCU/checklist.txt index 5c8d74968090..fc103d7a0474 100644 --- a/Documentation/RCU/checklist.txt +++ b/Documentation/RCU/checklist.txt @@ -162,9 +162,9 @@ over a rather long period of time, but improvements are always welcome! when publicizing a pointer to a structure that can be traversed by an RCU read-side critical section. -5. If call_rcu(), or a related primitive such as call_rcu_bh() or - call_rcu_sched(), is used, the callback function must be - written to be called from softirq context. In particular, +5. If call_rcu(), or a related primitive such as call_rcu_bh(), + call_rcu_sched(), or call_srcu() is used, the callback function + must be written to be called from softirq context. In particular, it cannot block. 6. Since synchronize_rcu() can block, it cannot be called from @@ -202,11 +202,12 @@ over a rather long period of time, but improvements are always welcome! updater uses call_rcu_sched() or synchronize_sched(), then the corresponding readers must disable preemption, possibly by calling rcu_read_lock_sched() and rcu_read_unlock_sched(). - If the updater uses synchronize_srcu(), the the corresponding - readers must use srcu_read_lock() and srcu_read_unlock(), - and with the same srcu_struct. The rules for the expedited - primitives are the same as for their non-expedited counterparts. - Mixing things up will result in confusion and broken kernels. + If the updater uses synchronize_srcu() or call_srcu(), + the the corresponding readers must use srcu_read_lock() and + srcu_read_unlock(), and with the same srcu_struct. The rules for + the expedited primitives are the same as for their non-expedited + counterparts. Mixing things up will result in confusion and + broken kernels. One exception to this rule: rcu_read_lock() and rcu_read_unlock() may be substituted for rcu_read_lock_bh() and rcu_read_unlock_bh() @@ -333,14 +334,14 @@ over a rather long period of time, but improvements are always welcome! victim CPU from ever going offline.) 14. SRCU (srcu_read_lock(), srcu_read_unlock(), srcu_dereference(), - synchronize_srcu(), and synchronize_srcu_expedited()) may only - be invoked from process context. Unlike other forms of RCU, it - -is- permissible to block in an SRCU read-side critical section - (demarked by srcu_read_lock() and srcu_read_unlock()), hence the - "SRCU": "sleepable RCU". Please note that if you don't need - to sleep in read-side critical sections, you should be using - RCU rather than SRCU, because RCU is almost always faster and - easier to use than is SRCU. + synchronize_srcu(), synchronize_srcu_expedited(), and call_srcu()) + may only be invoked from process context. Unlike other forms of + RCU, it -is- permissible to block in an SRCU read-side critical + section (demarked by srcu_read_lock() and srcu_read_unlock()), + hence the "SRCU": "sleepable RCU". Please note that if you + don't need to sleep in read-side critical sections, you should be + using RCU rather than SRCU, because RCU is almost always faster + and easier to use than is SRCU. If you need to enter your read-side critical section in a hardirq or exception handler, and then exit that same read-side @@ -353,8 +354,8 @@ over a rather long period of time, but improvements are always welcome! cleanup_srcu_struct(). These are passed a "struct srcu_struct" that defines the scope of a given SRCU domain. Once initialized, the srcu_struct is passed to srcu_read_lock(), srcu_read_unlock() - synchronize_srcu(), and synchronize_srcu_expedited(). A given - synchronize_srcu() waits only for SRCU read-side critical + synchronize_srcu(), synchronize_srcu_expedited(), and call_srcu(). + A given synchronize_srcu() waits only for SRCU read-side critical sections governed by srcu_read_lock() and srcu_read_unlock() calls that have been passed the same srcu_struct. This property is what makes sleeping read-side critical sections tolerable -- @@ -374,7 +375,7 @@ over a rather long period of time, but improvements are always welcome! requiring SRCU's read-side deadlock immunity or low read-side realtime latency. - Note that, rcu_assign_pointer() relates to SRCU just as they do + Note that, rcu_assign_pointer() relates to SRCU just as it does to other forms of RCU. 15. The whole point of call_rcu(), synchronize_rcu(), and friends diff --git a/Documentation/RCU/rcubarrier.txt b/Documentation/RCU/rcubarrier.txt index e439a0edee22..38428c125135 100644 --- a/Documentation/RCU/rcubarrier.txt +++ b/Documentation/RCU/rcubarrier.txt @@ -79,8 +79,6 @@ complete. Pseudo-code using rcu_barrier() is as follows: 2. Execute rcu_barrier(). 3. Allow the module to be unloaded. -Quick Quiz #1: Why is there no srcu_barrier()? - The rcutorture module makes use of rcu_barrier in its exit function as follows: @@ -162,7 +160,7 @@ for any pre-existing callbacks to complete. Then lines 55-62 print status and do operation-specific cleanup, and then return, permitting the module-unload operation to be completed. -Quick Quiz #2: Is there any other situation where rcu_barrier() might +Quick Quiz #1: Is there any other situation where rcu_barrier() might be required? Your module might have additional complications. For example, if your @@ -242,7 +240,7 @@ reaches zero, as follows: 4 complete(&rcu_barrier_completion); 5 } -Quick Quiz #3: What happens if CPU 0's rcu_barrier_func() executes +Quick Quiz #2: What happens if CPU 0's rcu_barrier_func() executes immediately (thus incrementing rcu_barrier_cpu_count to the value one), but the other CPU's rcu_barrier_func() invocations are delayed for a full grace period? Couldn't this result in @@ -259,12 +257,7 @@ so that your module may be safely unloaded. Answers to Quick Quizzes -Quick Quiz #1: Why is there no srcu_barrier()? - -Answer: Since there is no call_srcu(), there can be no outstanding SRCU - callbacks. Therefore, there is no need to wait for them. - -Quick Quiz #2: Is there any other situation where rcu_barrier() might +Quick Quiz #1: Is there any other situation where rcu_barrier() might be required? Answer: Interestingly enough, rcu_barrier() was not originally @@ -278,7 +271,7 @@ Answer: Interestingly enough, rcu_barrier() was not originally implementing rcutorture, and found that rcu_barrier() solves this problem as well. -Quick Quiz #3: What happens if CPU 0's rcu_barrier_func() executes +Quick Quiz #2: What happens if CPU 0's rcu_barrier_func() executes immediately (thus incrementing rcu_barrier_cpu_count to the value one), but the other CPU's rcu_barrier_func() invocations are delayed for a full grace period? Couldn't this result in diff --git a/Documentation/RCU/torture.txt b/Documentation/RCU/torture.txt index 4ddf3913fd8c..7dce8a17eac2 100644 --- a/Documentation/RCU/torture.txt +++ b/Documentation/RCU/torture.txt @@ -174,11 +174,20 @@ torture_type The type of RCU to test, with string values as follows: and synchronize_rcu_bh_expedited(). "srcu": srcu_read_lock(), srcu_read_unlock() and + call_srcu(). + + "srcu_sync": srcu_read_lock(), srcu_read_unlock() and synchronize_srcu(). "srcu_expedited": srcu_read_lock(), srcu_read_unlock() and synchronize_srcu_expedited(). + "srcu_raw": srcu_read_lock_raw(), srcu_read_unlock_raw(), + and call_srcu(). + + "srcu_raw_sync": srcu_read_lock_raw(), srcu_read_unlock_raw(), + and synchronize_srcu(). + "sched": preempt_disable(), preempt_enable(), and call_rcu_sched(). diff --git a/Documentation/RCU/whatisRCU.txt b/Documentation/RCU/whatisRCU.txt index 6bbe8dcdc3da..69ee188515e7 100644 --- a/Documentation/RCU/whatisRCU.txt +++ b/Documentation/RCU/whatisRCU.txt @@ -833,9 +833,9 @@ sched: Critical sections Grace period Barrier SRCU: Critical sections Grace period Barrier - srcu_read_lock synchronize_srcu N/A - srcu_read_unlock synchronize_srcu_expedited - srcu_read_lock_raw + srcu_read_lock synchronize_srcu srcu_barrier + srcu_read_unlock call_srcu + srcu_read_lock_raw synchronize_srcu_expedited srcu_read_unlock_raw srcu_dereference diff --git a/Documentation/devicetree/bindings/mfd/tps65910.txt b/Documentation/devicetree/bindings/mfd/tps65910.txt index 645f5eaadb3f..d2802d4717bc 100644 --- a/Documentation/devicetree/bindings/mfd/tps65910.txt +++ b/Documentation/devicetree/bindings/mfd/tps65910.txt @@ -17,18 +17,46 @@ Required properties: device need to be present. The definition for each of these nodes is defined using the standard binding for regulators found at Documentation/devicetree/bindings/regulator/regulator.txt. + The regulator is matched with the regulator-compatible. - The valid names for regulators are: + The valid regulator-compatible values are: tps65910: vrtc, vio, vdd1, vdd2, vdd3, vdig1, vdig2, vpll, vdac, vaux1, vaux2, vaux33, vmmc tps65911: vrtc, vio, vdd1, vdd3, vddctrl, ldo1, ldo2, ldo3, ldo4, ldo5, ldo6, ldo7, ldo8 +- xxx-supply: Input voltage supply regulator. + These entries are require if regulators are enabled for a device. Missing of these + properties can cause the regulator registration fails. + If some of input supply is powered through battery or always-on supply then + also it is require to have these parameters with proper node handle of always + on power supply. + tps65910: + vcc1-supply: VDD1 input. + vcc2-supply: VDD2 input. + vcc3-supply: VAUX33 and VMMC input. + vcc4-supply: VAUX1 and VAUX2 input. + vcc5-supply: VPLL and VDAC input. + vcc6-supply: VDIG1 and VDIG2 input. + vcc7-supply: VRTC input. + vccio-supply: VIO input. + tps65911: + vcc1-supply: VDD1 input. + vcc2-supply: VDD2 input. + vcc3-supply: LDO6, LDO7 and LDO8 input. + vcc4-supply: LDO5 input. + vcc5-supply: LDO3 and LDO4 input. + vcc6-supply: LDO1 and LDO2 input. + vcc7-supply: VRTC input. + vccio-supply: VIO input. + Optional properties: - ti,vmbch-threshold: (tps65911) main battery charged threshold comparator. (see VMBCH_VSEL in TPS65910 datasheet) - ti,vmbch2-threshold: (tps65911) main battery discharged threshold comparator. (see VMBCH_VSEL in TPS65910 datasheet) +- ti,en-ck32k-xtal: enable external 32-kHz crystal oscillator (see CK32K_CTRL + in TPS6591X datasheet) - ti,en-gpio-sleep: enable sleep control for gpios There should be 9 entries here, one for each gpio. @@ -56,74 +84,110 @@ Example: ti,en-gpio-sleep = <0 0 1 0 0 0 0 0 0>; + vcc1-supply = <®_parent>; + vcc2-supply = <&some_reg>; + vcc3-supply = <...>; + vcc4-supply = <...>; + vcc5-supply = <...>; + vcc6-supply = <...>; + vcc7-supply = <...>; + vccio-supply = <...>; + regulators { - vdd1_reg: vdd1 { + #address-cells = <1>; + #size-cells = <0>; + + vdd1_reg: regulator@0 { + regulator-compatible = "vdd1"; + reg = <0>; regulator-min-microvolt = < 600000>; regulator-max-microvolt = <1500000>; regulator-always-on; regulator-boot-on; ti,regulator-ext-sleep-control = <0>; }; - vdd2_reg: vdd2 { + vdd2_reg: regulator@1 { + regulator-compatible = "vdd2"; + reg = <1>; regulator-min-microvolt = < 600000>; regulator-max-microvolt = <1500000>; regulator-always-on; regulator-boot-on; ti,regulator-ext-sleep-control = <4>; }; - vddctrl_reg: vddctrl { + vddctrl_reg: regulator@2 { + regulator-compatible = "vddctrl"; + reg = <2>; regulator-min-microvolt = < 600000>; regulator-max-microvolt = <1400000>; regulator-always-on; regulator-boot-on; ti,regulator-ext-sleep-control = <0>; }; - vio_reg: vio { + vio_reg: regulator@3 { + regulator-compatible = "vio"; + reg = <3>; regulator-min-microvolt = <1500000>; regulator-max-microvolt = <1800000>; regulator-always-on; regulator-boot-on; ti,regulator-ext-sleep-control = <1>; }; - ldo1_reg: ldo1 { + ldo1_reg: regulator@4 { + regulator-compatible = "ldo1"; + reg = <4>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; ti,regulator-ext-sleep-control = <0>; }; - ldo2_reg: ldo2 { + ldo2_reg: regulator@5 { + regulator-compatible = "ldo2"; + reg = <5>; regulator-min-microvolt = <1050000>; regulator-max-microvolt = <1050000>; ti,regulator-ext-sleep-control = <0>; }; - ldo3_reg: ldo3 { + ldo3_reg: regulator@6 { + regulator-compatible = "ldo3"; + reg = <6>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; ti,regulator-ext-sleep-control = <0>; }; - ldo4_reg: ldo4 { + ldo4_reg: regulator@7 { + regulator-compatible = "ldo4"; + reg = <7>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; regulator-always-on; ti,regulator-ext-sleep-control = <0>; }; - ldo5_reg: ldo5 { + ldo5_reg: regulator@8 { + regulator-compatible = "ldo5"; + reg = <8>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; ti,regulator-ext-sleep-control = <0>; }; - ldo6_reg: ldo6 { + ldo6_reg: regulator@9 { + regulator-compatible = "ldo6"; + reg = <9>; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; ti,regulator-ext-sleep-control = <0>; }; - ldo7_reg: ldo7 { + ldo7_reg: regulator@10 { + regulator-compatible = "ldo7"; + reg = <10>; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; regulator-always-on; regulator-boot-on; ti,regulator-ext-sleep-control = <1>; }; - ldo8_reg: ldo8 { + ldo8_reg: regulator@11 { + regulator-compatible = "ldo8"; + reg = <11>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; regulator-always-on; diff --git a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt index 0d93b4b0e0e3..bd9be0b5bc20 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt @@ -3,21 +3,22 @@ The Enhanced Secure Digital Host Controller provides an interface for MMC, SD, and SDIO types of memory cards. +This file documents differences between the core properties described +by mmc.txt and the properties used by the sdhci-esdhc driver. + Required properties: - - compatible : should be - "fsl,<chip>-esdhc", "fsl,esdhc" - - reg : should contain eSDHC registers location and length. - - interrupts : should contain eSDHC interrupt. - interrupt-parent : interrupt source phandle. - clock-frequency : specifies eSDHC base clock frequency. - - sdhci,wp-inverted : (optional) specifies that eSDHC controller - reports inverted write-protect state; New devices should use - the generic "wp-inverted" property. - - sdhci,1-bit-only : (optional) specifies that a controller can - only handle 1-bit data transfers. New devices should use the - generic "bus-width = <1>" property. - - sdhci,auto-cmd12: (optional) specifies that a controller can - only handle auto CMD12. + +Optional properties: + - sdhci,wp-inverted : specifies that eSDHC controller reports + inverted write-protect state; New devices should use the generic + "wp-inverted" property. + - sdhci,1-bit-only : specifies that a controller can only handle + 1-bit data transfers. New devices should use the generic + "bus-width = <1>" property. + - sdhci,auto-cmd12: specifies that a controller can only handle auto + CMD12. Example: diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt index fea541ee8b34..70cd49b1caa8 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -3,17 +3,15 @@ The Enhanced Secure Digital Host Controller on Freescale i.MX family provides an interface for MMC, SD, and SDIO types of memory cards. +This file documents differences between the core properties described +by mmc.txt and the properties used by the sdhci-esdhc-imx driver. + Required properties: - compatible : Should be "fsl,<chip>-esdhc" -- reg : Should contain eSDHC registers location and length -- interrupts : Should contain eSDHC interrupt Optional properties: -- non-removable : Indicate the card is wired to host permanently - fsl,cd-internal : Indicate to use controller internal card detection - fsl,wp-internal : Indicate to use controller internal write protection -- cd-gpios : Specify GPIOs for card detection -- wp-gpios : Specify GPIOs for write protection Examples: diff --git a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt index d64aea5a4203..0e5e2ec4001d 100644 --- a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt +++ b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt @@ -1,8 +1,9 @@ MMC/SD/SDIO slot directly connected to a SPI bus +This file documents differences between the core properties described +by mmc.txt and the properties used by the mmc_spi driver. + Required properties: -- compatible : should be "mmc-spi-slot". -- reg : should specify SPI address (chip-select number). - spi-max-frequency : maximum frequency for this device (Hz). - voltage-ranges : two cells are required, first cell specifies minimum slot voltage (mV), second cell specifies maximum slot voltage (mV). @@ -11,8 +12,7 @@ Required properties: Optional properties: - gpios : may specify GPIOs in this order: Card-Detect GPIO, Write-Protect GPIO. Note that this does not follow the - binding from mmc.txt, for historic reasons. -- interrupts : the interrupt of a card detect interrupt. + binding from mmc.txt, for historical reasons. - interrupt-parent : the phandle for the interrupt controller that services interrupts for this device. diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 6e70dcde0a71..8a6811f4a02f 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -2,13 +2,17 @@ These properties are common to multiple MMC host controllers. Any host that requires the respective functionality should implement them using these definitions. +Interpreted by the OF core: +- reg: Registers location and length. +- interrupts: Interrupts used by the MMC controller. + Required properties: - bus-width: Number of data lines, can be <1>, <4>, or <8> Optional properties: -- cd-gpios : Specify GPIOs for card detection, see gpio binding -- wp-gpios : Specify GPIOs for write protection, see gpio binding -- cd-inverted: when present, polarity on the wp gpio line is inverted +- cd-gpios: Specify GPIOs for card detection, see gpio binding +- wp-gpios: Specify GPIOs for write protection, see gpio binding +- cd-inverted: when present, polarity on the cd gpio line is inverted - wp-inverted: when present, polarity on the wp gpio line is inverted - non-removable: non-removable slot (like eMMC) - max-frequency: maximum operating clock frequency diff --git a/Documentation/devicetree/bindings/mmc/mmci.txt b/Documentation/devicetree/bindings/mmc/mmci.txt index 14a81d526118..2b584cae352a 100644 --- a/Documentation/devicetree/bindings/mmc/mmci.txt +++ b/Documentation/devicetree/bindings/mmc/mmci.txt @@ -1,19 +1,15 @@ * ARM PrimeCell MultiMedia Card Interface (MMCI) PL180/1 -The ARM PrimeCell MMCI PL180 and PL181 provides and interface for +The ARM PrimeCell MMCI PL180 and PL181 provides an interface for reading and writing to MultiMedia and SD cards alike. +This file documents differences between the core properties described +by mmc.txt and the properties used by the mmci driver. + Required properties: - compatible : contains "arm,pl18x", "arm,primecell". -- reg : contains pl18x registers and length. -- interrupts : contains the device IRQ(s). - arm,primecell-periphid : contains the PrimeCell Peripheral ID. Optional properties: -- wp-gpios : contains any write protect (ro) gpios -- cd-gpios : contains any card detection gpios -- cd-inverted : indicates whether the cd gpio is inverted -- max-frequency : contains the maximum operating frequency -- bus-width : number of data lines, can be <1>, <4>, or <8> - mmc-cap-mmc-highspeed : indicates whether MMC is high speed capable - mmc-cap-sd-highspeed : indicates whether SD is high speed capable diff --git a/Documentation/devicetree/bindings/mmc/mxs-mmc.txt b/Documentation/devicetree/bindings/mmc/mxs-mmc.txt index 14d870a9e3db..54949f6faede 100644 --- a/Documentation/devicetree/bindings/mmc/mxs-mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mxs-mmc.txt @@ -3,16 +3,14 @@ The Freescale MXS Synchronous Serial Ports (SSP) can act as a MMC controller to support MMC, SD, and SDIO types of memory cards. +This file documents differences between the core properties in mmc.txt +and the properties used by the mxsmmc driver. + Required properties: - compatible: Should be "fsl,<chip>-mmc". The supported chips include imx23 and imx28. -- reg: Should contain registers location and length - interrupts: Should contain ERROR and DMA interrupts - fsl,ssp-dma-channel: APBH DMA channel for the SSP -- bus-width: Number of data lines, can be <1>, <4>, or <8> - -Optional properties: -- wp-gpios: Specify GPIOs for write protection Examples: diff --git a/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt b/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt index f77c3031607f..c6d7b11db9eb 100644 --- a/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt @@ -3,15 +3,13 @@ This controller on Tegra family SoCs provides an interface for MMC, SD, and SDIO types of memory cards. +This file documents differences between the core properties described +by mmc.txt and the properties used by the sdhci-tegra driver. + Required properties: - compatible : Should be "nvidia,<chip>-sdhci" -- reg : Should contain SD/MMC registers location and length -- interrupts : Should contain SD/MMC interrupt -- bus-width : Number of data lines, can be <1>, <4>, or <8> Optional properties: -- cd-gpios : Specify GPIOs for card detection -- wp-gpios : Specify GPIOs for write protection - power-gpios : Specify GPIOs for power control Example: diff --git a/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt b/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt new file mode 100644 index 000000000000..dbe98a3c183a --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt @@ -0,0 +1,21 @@ +* Marvell sdhci-pxa v2/v3 controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-pxav2 and sdhci-pxav3 drivers. + +Required properties: +- compatible: Should be "mrvl,pxav2-mmc" or "mrvl,pxav3-mmc". + +Optional properties: +- mrvl,clk-delay-cycles: Specify a number of cycles to delay for tuning. + +Example: + +sdhci@d4280800 { + compatible = "mrvl,pxav3-mmc"; + reg = <0xd4280800 0x800>; + bus-width = <8>; + interrupts = <27>; + non-removable; + mrvl,clk-delay-cycles = <31>; +}; diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt index 8a53958c9a9f..be76a23b34c4 100644 --- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt @@ -3,21 +3,20 @@ The Highspeed MMC Host Controller on TI OMAP family provides an interface for MMC, SD, and SDIO types of memory cards. +This file documents differences between the core properties described +by mmc.txt and the properties used by the omap_hsmmc driver. + Required properties: - compatible: Should be "ti,omap2-hsmmc", for OMAP2 controllers Should be "ti,omap3-hsmmc", for OMAP3 controllers Should be "ti,omap4-hsmmc", for OMAP4 controllers - ti,hwmods: Must be "mmc<n>", n is controller instance starting 1 -- reg : should contain hsmmc registers location and length Optional properties: ti,dual-volt: boolean, supports dual voltage cards <supply-name>-supply: phandle to the regulator device tree node "supply-name" examples are "vmmc", "vmmc_aux" etc -bus-width: Number of data lines, default assumed is 1 if the property is missing. -cd-gpios: GPIOs for card detection -wp-gpios: GPIOs for write protection ti,non-removable: non-removable slot (like eMMC) ti,needs-special-reset: Requires a special softreset sequence diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx6q-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx6q-pinctrl.txt index 82b43f915857..a4119f6422d9 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx6q-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx6q-pinctrl.txt @@ -1626,3 +1626,5 @@ MX6Q_PAD_SD2_DAT3__PCIE_CTRL_MUX_11 1587 MX6Q_PAD_SD2_DAT3__GPIO_1_12 1588 MX6Q_PAD_SD2_DAT3__SJC_DONE 1589 MX6Q_PAD_SD2_DAT3__ANATOP_TESTO_3 1590 +MX6Q_PAD_ENET_RX_ER__ANATOP_USBOTG_ID 1591 +MX6Q_PAD_GPIO_1__ANATOP_USBOTG_ID 1592 diff --git a/Documentation/devicetree/bindings/regulator/fixed-regulator.txt b/Documentation/devicetree/bindings/regulator/fixed-regulator.txt index 2f5b6b1ba15f..4fae41d54798 100644 --- a/Documentation/devicetree/bindings/regulator/fixed-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/fixed-regulator.txt @@ -10,6 +10,7 @@ Optional properties: If this property is missing, the default assumed is Active low. - gpio-open-drain: GPIO is open drain type. If this property is missing then default assumption is false. +-vin-supply: Input supply name. Any property defined as part of the core regulator binding, defined in regulator.txt, can also be used. @@ -29,4 +30,5 @@ Example: enable-active-high; regulator-boot-on; gpio-open-drain; + vin-supply = <&parent_reg>; }; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 5b7a408acdaa..66ece3f87bbc 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -10,6 +10,11 @@ Optional properties: - regulator-always-on: boolean, regulator should never be disabled - regulator-boot-on: bootloader/firmware enabled regulator - <name>-supply: phandle to the parent supply/regulator node +- regulator-ramp-delay: ramp delay for regulator(in uV/uS) +- regulator-compatible: If a regulator chip contains multiple + regulators, and if the chip's binding contains a child node that + describes each regulator, then this property indicates which regulator + this child node is intended to configure. Example: diff --git a/Documentation/devicetree/bindings/regulator/tps65217.txt b/Documentation/devicetree/bindings/regulator/tps65217.txt new file mode 100644 index 000000000000..0487e9675ba0 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/tps65217.txt @@ -0,0 +1,91 @@ +TPS65217 family of regulators + +Required properties: +- compatible: "ti,tps65217" +- reg: I2C slave address +- regulators: list of regulators provided by this controller, must be named + after their hardware counterparts: dcdc[1-3] and ldo[1-4] +- regulators: This is the list of child nodes that specify the regulator + initialization data for defined regulators. Not all regulators for the given + device need to be present. The definition for each of these nodes is defined + using the standard binding for regulators found at + Documentation/devicetree/bindings/regulator/regulator.txt. + + The valid names for regulators are: + tps65217: dcdc1, dcdc2, dcdc3, ldo1, ldo2, ldo3 and ldo4 + +Each regulator is defined using the standard binding for regulators. + +Example: + + tps: tps@24 { + compatible = "ti,tps65217"; + + regulators { + #address-cells = <1>; + #size-cells = <0>; + + dcdc1_reg: regulator@0 { + reg = <0>; + regulator-compatible = "dcdc1"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc2_reg: regulator@1 { + reg = <1>; + regulator-compatible = "dcdc2"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3_reg: regulator@2 { + reg = <2>; + regulator-compatible = "dcdc3"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: regulator@3 { + reg = <3>; + regulator-compatible = "ldo1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: regulator@4 { + reg = <4>; + regulator-compatible = "ldo2"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: regulator@5 { + reg = <5>; + regulator-compatible = "ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: regulator@6 { + reg = <6>; + regulator-compatible = "ldo4"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/tps6586x.txt b/Documentation/devicetree/bindings/regulator/tps6586x.txt index 0fcabaa3baa3..d156e1b5db12 100644 --- a/Documentation/devicetree/bindings/regulator/tps6586x.txt +++ b/Documentation/devicetree/bindings/regulator/tps6586x.txt @@ -6,8 +6,17 @@ Required properties: - interrupts: the interrupt outputs of the controller - #gpio-cells: number of cells to describe a GPIO - gpio-controller: mark the device as a GPIO controller -- regulators: list of regulators provided by this controller, must be named - after their hardware counterparts: sm[0-2], ldo[0-9] and ldo_rtc +- regulators: list of regulators provided by this controller, must have + property "regulator-compatible" to match their hardware counterparts: + sm[0-2], ldo[0-9] and ldo_rtc +- sm0-supply: The input supply for the SM0. +- sm1-supply: The input supply for the SM1. +- sm2-supply: The input supply for the SM2. +- vinldo01-supply: The input supply for the LDO1 and LDO2 +- vinldo23-supply: The input supply for the LDO2 and LDO3 +- vinldo4-supply: The input supply for the LDO4 +- vinldo678-supply: The input supply for the LDO6, LDO7 and LDO8 +- vinldo9-supply: The input supply for the LDO9 Each regulator is defined using the standard binding for regulators. @@ -21,75 +30,113 @@ Example: #gpio-cells = <2>; gpio-controller; + sm0-supply = <&some_reg>; + sm1-supply = <&some_reg>; + sm2-supply = <&some_reg>; + vinldo01-supply = <...>; + vinldo23-supply = <...>; + vinldo4-supply = <...>; + vinldo678-supply = <...>; + vinldo9-supply = <...>; + regulators { - sm0_reg: sm0 { + #address-cells = <1>; + #size-cells = <0>; + + sm0_reg: regulator@0 { + reg = <0>; + regulator-compatible = "sm0"; regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; regulator-boot-on; regulator-always-on; }; - sm1_reg: sm1 { + sm1_reg: regulator@1 { + reg = <1>; + regulator-compatible = "sm1"; regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; regulator-boot-on; regulator-always-on; }; - sm2_reg: sm2 { + sm2_reg: regulator@2 { + reg = <2>; + regulator-compatible = "sm2"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <4550000>; regulator-boot-on; regulator-always-on; }; - ldo0_reg: ldo0 { + ldo0_reg: regulator@3 { + reg = <3>; + regulator-compatible = "ldo0"; regulator-name = "PCIE CLK"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; - ldo1_reg: ldo1 { + ldo1_reg: regulator@4 { + reg = <4>; + regulator-compatible = "ldo1"; regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; }; - ldo2_reg: ldo2 { + ldo2_reg: regulator@5 { + reg = <5>; + regulator-compatible = "ldo2"; regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; }; - ldo3_reg: ldo3 { + ldo3_reg: regulator@6 { + reg = <6>; + regulator-compatible = "ldo3"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo4_reg: ldo4 { + ldo4_reg: regulator@7 { + reg = <7>; + regulator-compatible = "ldo4"; regulator-min-microvolt = <1700000>; regulator-max-microvolt = <2475000>; }; - ldo5_reg: ldo5 { + ldo5_reg: regulator@8 { + reg = <8>; + regulator-compatible = "ldo5"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo6_reg: ldo6 { + ldo6_reg: regulator@9 { + reg = <9>; + regulator-compatible = "ldo6"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo7_reg: ldo7 { + ldo7_reg: regulator@10 { + reg = <10>; + regulator-compatible = "ldo7"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo8_reg: ldo8 { + ldo8_reg: regulator@11 { + reg = <11>; + regulator-compatible = "ldo8"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo9_reg: ldo9 { + ldo9_reg: regulator@12 { + reg = <12>; + regulator-compatible = "ldo9"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; diff --git a/Documentation/devicetree/bindings/regulator/twl-regulator.txt b/Documentation/devicetree/bindings/regulator/twl-regulator.txt index 0c3395d55ac1..658749b90b97 100644 --- a/Documentation/devicetree/bindings/regulator/twl-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/twl-regulator.txt @@ -15,7 +15,6 @@ For twl6030 regulators/LDOs - "ti,twl6030-vusb" for VUSB LDO - "ti,twl6030-v1v8" for V1V8 LDO - "ti,twl6030-v2v1" for V2V1 LDO - - "ti,twl6030-clk32kg" for CLK32KG RESOURCE - "ti,twl6030-vdd1" for VDD1 SMPS - "ti,twl6030-vdd2" for VDD2 SMPS - "ti,twl6030-vdd3" for VDD3 SMPS diff --git a/Documentation/filesystems/Locking b/Documentation/filesystems/Locking index 8e2da1e06e3b..e0cce2a5f820 100644 --- a/Documentation/filesystems/Locking +++ b/Documentation/filesystems/Locking @@ -9,7 +9,7 @@ be able to use diff(1). --------------------------- dentry_operations -------------------------- prototypes: - int (*d_revalidate)(struct dentry *, struct nameidata *); + int (*d_revalidate)(struct dentry *, unsigned int); int (*d_hash)(const struct dentry *, const struct inode *, struct qstr *); int (*d_compare)(const struct dentry *, const struct inode *, @@ -37,9 +37,8 @@ d_manage: no no yes (ref-walk) maybe --------------------------- inode_operations --------------------------- prototypes: - int (*create) (struct inode *,struct dentry *,umode_t, struct nameidata *); - struct dentry * (*lookup) (struct inode *,struct dentry *, struct nameid -ata *); + int (*create) (struct inode *,struct dentry *,umode_t, bool); + struct dentry * (*lookup) (struct inode *,struct dentry *, unsigned int); int (*link) (struct dentry *,struct inode *,struct dentry *); int (*unlink) (struct inode *,struct dentry *); int (*symlink) (struct inode *,struct dentry *,const char *); @@ -62,6 +61,9 @@ ata *); int (*removexattr) (struct dentry *, const char *); int (*fiemap)(struct inode *, struct fiemap_extent_info *, u64 start, u64 len); void (*update_time)(struct inode *, struct timespec *, int); + int (*atomic_open)(struct inode *, struct dentry *, + struct file *, unsigned open_flag, + umode_t create_mode, int *opened); locking rules: all may block @@ -89,6 +91,7 @@ listxattr: no removexattr: yes fiemap: no update_time: no +atomic_open: yes Additionally, ->rmdir(), ->unlink() and ->rename() have ->i_mutex on victim. diff --git a/Documentation/filesystems/porting b/Documentation/filesystems/porting index 8c91d1057d9a..2bef2b3843d1 100644 --- a/Documentation/filesystems/porting +++ b/Documentation/filesystems/porting @@ -355,12 +355,10 @@ protects *all* the dcache state of a given dentry. via rcu-walk path walk (basically, if the file can have had a path name in the vfs namespace). - i_dentry and i_rcu share storage in a union, and the vfs expects -i_dentry to be reinitialized before it is freed, so an: - - INIT_LIST_HEAD(&inode->i_dentry); - -must be done in the RCU callback. + Even though i_dentry and i_rcu share storage in a union, we will +initialize the former in inode_init_always(), so just leave it alone in +the callback. It used to be necessary to clean it there, but not anymore +(starting at 3.2). -- [recommended] @@ -433,3 +431,14 @@ release it yourself. d_alloc_root() is gone, along with a lot of bugs caused by code misusing it. Replacement: d_make_root(inode). The difference is, d_make_root() drops the reference to inode if dentry allocation fails. + +-- +[mandatory] + The witch is dead! Well, 2/3 of it, anyway. ->d_revalidate() and +->lookup() do *not* take struct nameidata anymore; just the flags. +-- +[mandatory] + ->create() doesn't take struct nameidata *; unlike the previous +two, it gets "is it an O_EXCL or equivalent?" boolean argument. Note that +local filesystems can ignore tha argument - they are guaranteed that the +object doesn't exist. It's remote/distributed ones that might care... diff --git a/Documentation/filesystems/vfs.txt b/Documentation/filesystems/vfs.txt index efd23f481704..aa754e01464e 100644 --- a/Documentation/filesystems/vfs.txt +++ b/Documentation/filesystems/vfs.txt @@ -341,8 +341,8 @@ This describes how the VFS can manipulate an inode in your filesystem. As of kernel 2.6.22, the following members are defined: struct inode_operations { - int (*create) (struct inode *,struct dentry *, umode_t, struct nameidata *); - struct dentry * (*lookup) (struct inode *,struct dentry *, struct nameidata *); + int (*create) (struct inode *,struct dentry *, umode_t, bool); + struct dentry * (*lookup) (struct inode *,struct dentry *, unsigned int); int (*link) (struct dentry *,struct inode *,struct dentry *); int (*unlink) (struct inode *,struct dentry *); int (*symlink) (struct inode *,struct dentry *,const char *); @@ -364,6 +364,9 @@ struct inode_operations { ssize_t (*listxattr) (struct dentry *, char *, size_t); int (*removexattr) (struct dentry *, const char *); void (*update_time)(struct inode *, struct timespec *, int); + int (*atomic_open)(struct inode *, struct dentry *, + struct file *, unsigned open_flag, + umode_t create_mode, int *opened); }; Again, all methods are called without any locks being held, unless @@ -476,6 +479,14 @@ otherwise noted. an inode. If this is not defined the VFS will update the inode itself and call mark_inode_dirty_sync. + atomic_open: called on the last component of an open. Using this optional + method the filesystem can look up, possibly create and open the file in + one atomic operation. If it cannot perform this (e.g. the file type + turned out to be wrong) it may signal this by returning 1 instead of + usual 0 or -ve . This method is only called if the last + component is negative or needs lookup. Cached positive dentries are + still handled by f_op->open(). + The Address Space Object ======================== @@ -891,7 +902,7 @@ the VFS uses a default. As of kernel 2.6.22, the following members are defined: struct dentry_operations { - int (*d_revalidate)(struct dentry *, struct nameidata *); + int (*d_revalidate)(struct dentry *, unsigned int); int (*d_hash)(const struct dentry *, const struct inode *, struct qstr *); int (*d_compare)(const struct dentry *, const struct inode *, @@ -910,11 +921,11 @@ struct dentry_operations { dcache. Most filesystems leave this as NULL, because all their dentries in the dcache are valid - d_revalidate may be called in rcu-walk mode (nd->flags & LOOKUP_RCU). + d_revalidate may be called in rcu-walk mode (flags & LOOKUP_RCU). If in rcu-walk mode, the filesystem must revalidate the dentry without blocking or storing to the dentry, d_parent and d_inode should not be - used without care (because they can go NULL), instead nd->inode should - be used. + used without care (because they can change and, in d_inode case, even + become NULL under us). If a situation is encountered that rcu-walk cannot handle, return -ECHILD and it will be called again in ref-walk mode. diff --git a/Documentation/kdump/kdump.txt b/Documentation/kdump/kdump.txt index 506c7390c2b9..13f1aa09b938 100644 --- a/Documentation/kdump/kdump.txt +++ b/Documentation/kdump/kdump.txt @@ -86,7 +86,7 @@ There is also a gitweb interface available at http://www.kernel.org/git/?p=utils/kernel/kexec/kexec-tools.git More information about kexec-tools can be found at -http://www.kernel.org/pub/linux/utils/kernel/kexec/README.html +http://horms.net/projects/kexec/ 3) Unpack the tarball with the tar command, as follows: diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index a92c5ebf373e..12783fa833c3 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -2367,6 +2367,11 @@ bytes respectively. Such letter suffixes can also be entirely omitted. Set maximum number of finished RCU callbacks to process in one batch. + rcutree.fanout_leaf= [KNL,BOOT] + Increase the number of CPUs assigned to each + leaf rcu_node structure. Useful for very large + systems. + rcutree.qhimark= [KNL,BOOT] Set threshold of queued RCU callbacks over which batch limiting is disabled. diff --git a/Documentation/power/devices.txt b/Documentation/power/devices.txt index 872815cd41d3..504dfe4d52eb 100644 --- a/Documentation/power/devices.txt +++ b/Documentation/power/devices.txt @@ -583,9 +583,10 @@ for the given device during all power transitions, instead of the respective subsystem-level callbacks. Specifically, if a device's pm_domain pointer is not NULL, the ->suspend() callback from the object pointed to by it will be executed instead of its subsystem's (e.g. bus type's) ->suspend() callback and -anlogously for all of the remaining callbacks. In other words, power management -domain callbacks, if defined for the given device, always take precedence over -the callbacks provided by the device's subsystem (e.g. bus type). +analogously for all of the remaining callbacks. In other words, power +management domain callbacks, if defined for the given device, always take +precedence over the callbacks provided by the device's subsystem (e.g. bus +type). The support for device power management domains is only relevant to platforms needing to use the same device driver power management callbacks in many @@ -598,7 +599,7 @@ it into account in any way. Device Low Power (suspend) States --------------------------------- Device low-power states aren't standard. One device might only handle -"on" and "off, while another might support a dozen different versions of +"on" and "off", while another might support a dozen different versions of "on" (how many engines are active?), plus a state that gets back to "on" faster than from a full "off". diff --git a/Documentation/power/swsusp.txt b/Documentation/power/swsusp.txt index ac190cf1963e..92341b84250d 100644 --- a/Documentation/power/swsusp.txt +++ b/Documentation/power/swsusp.txt @@ -33,6 +33,11 @@ echo shutdown > /sys/power/disk; echo disk > /sys/power/state echo platform > /sys/power/disk; echo disk > /sys/power/state +. If you would like to write hibernation image to swap and then suspend +to RAM (provided your platform supports it), you can try + +echo suspend > /sys/power/disk; echo disk > /sys/power/state + . If you have SATA disks, you'll need recent kernels with SATA suspend support. For suspend and resume to work, make sure your disk drivers are built into kernel -- not modules. [There's way to make |