3 files changed, 131 insertions, 41 deletions
diff --git a/Documentation/acpi/gpio-properties.txt b/Documentation/acpi/gpio-properties.txt
index 5aafe0b351a1..2aff0349facd 100644
--- a/Documentation/acpi/gpio-properties.txt
+++ b/Documentation/acpi/gpio-properties.txt
@@ -51,6 +51,68 @@ it to 1 marks the GPIO as active low.
 In our Bluetooth example the "reset-gpios" refers to the second GpioIo()
 resource, second pin in that resource with the GPIO number of 31.
 
+It is possible to leave holes in the array of GPIOs. This is useful in
+cases like with SPI host controllers where some chip selects may be
+implemented as GPIOs and some as native signals. For example a SPI host
+controller can have chip selects 0 and 2 implemented as GPIOs and 1 as
+native:
+
+  Package () {
+      "cs-gpios",
+      Package () {
+          ^GPIO, 19, 0, 0, // chip select 0: GPIO
+          0,               // chip select 1: native signal
+          ^GPIO, 20, 0, 0, // chip select 2: GPIO
+      }
+  }
+
+Other supported properties
+--------------------------
+
+Following Device Tree compatible device properties are also supported by
+_DSD device properties for GPIO controllers:
+
+- gpio-hog
+- output-high
+- output-low
+- input
+- line-name
+
+Example:
+
+  Name (_DSD, Package () {
+      // _DSD Hierarchical Properties Extension UUID
+      ToUUID("dbb8e3e6-5886-4ba6-8795-1319f52a966b"),
+      Package () {
+          Package () {"hog-gpio8", "G8PU"}
+      }
+  })
+
+  Name (G8PU, Package () {
+      ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
+      Package () {
+          Package () {"gpio-hog", 1},
+          Package () {"gpios", Package () {8, 0}},
+          Package () {"output-high", 1},
+          Package () {"line-name", "gpio8-pullup"},
+      }
+  })
+
+- gpio-line-names
+
+Example:
+
+  Package () {
+      "gpio-line-names",
+      Package () {
+          "SPI0_CS_N", "EXP2_INT", "MUX6_IO", "UART0_RXD", "MUX7_IO",
+          "LVL_C_A1", "MUX0_IO", "SPI1_MISO"
+      }
+  }
+
+See Documentation/devicetree/bindings/gpio/gpio.txt for more information
+about these properties.
+
 ACPI GPIO Mappings Provided by Drivers
 --------------------------------------
 
diff --git a/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt b/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt
deleted file mode 100644
index c809acb9c71b..000000000000
--- a/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt
+++ /dev/null
@@ -1,41 +0,0 @@
-SEMTECH SX150x GPIO expander bindings
-
-
-Required properties:
-
-- compatible: should be "semtech,sx1506q",
-			"semtech,sx1508q",
-			"semtech,sx1509q",
-			"semtech,sx1502q".
-
-- reg: The I2C slave address for this device.
-
-- interrupt-parent: phandle of the parent interrupt controller.
-
-- interrupts: Interrupt specifier for the controllers interrupt.
-
-- #gpio-cells: Should be 2. The first cell is the GPIO number and the
-		second cell is used to specify optional parameters:
-		bit 0: polarity (0: normal, 1: inverted)
-
-- gpio-controller: Marks the device as a GPIO controller.
-
-- interrupt-controller: Marks the device as a interrupt controller.
-
-The GPIO expander can optionally be used as an interrupt controller, in
-which case it uses the default two cell specifier as described in
-Documentation/devicetree/bindings/interrupt-controller/interrupts.txt.
-
-Example:
-
-	i2c_gpio_expander@20{
-		#gpio-cells = <2>;
-		#interrupt-cells = <2>;
-		compatible = "semtech,sx1506q";
-		reg = <0x20>;
-		interrupt-parent = <&gpio_1>;
-		interrupts = <16 0>;
-
-		gpio-controller;
-		interrupt-controller;
-	};
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt
new file mode 100644
index 000000000000..c293c8aaac73
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt
@@ -0,0 +1,69 @@
+SEMTECH SX150x GPIO expander bindings
+
+Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and
+../interrupt-controller/interrupts.txt for generic information regarding
+pin controller, GPIO, and interrupt bindings.
+
+Required properties:
+- compatible: should be one of :
+			"semtech,sx1506q",
+			"semtech,sx1508q",
+			"semtech,sx1509q",
+			"semtech,sx1502q".
+
+- reg: The I2C slave address for this device.
+
+- #gpio-cells: Should be 2. The first cell is the GPIO number and the
+		second cell is used to specify optional parameters:
+		bit 0: polarity (0: normal, 1: inverted)
+
+- gpio-controller: Marks the device as a GPIO controller.
+
+Optional properties :
+- interrupt-parent: phandle of the parent interrupt controller.
+
+- interrupts: Interrupt specifier for the controllers interrupt.
+
+- interrupt-controller: Marks the device as a interrupt controller.
+
+- semtech,probe-reset: Will trigger a reset of the GPIO expander on probe,
+		only for sx1508q and sx1509q
+
+The GPIO expander can optionally be used as an interrupt controller, in
+which case it uses the default two cell specifier.
+
+Required properties for pin configuration sub-nodes:
+ - pins: List of pins to which the configuration applies.
+
+Optional properties for pin configuration sub-nodes:
+----------------------------------------------------
+ - bias-disable: disable any pin bias, except the OSCIO pin
+ - bias-pull-up: pull up the pin, except the OSCIO pin
+ - bias-pull-down: pull down the pin, except the OSCIO pin
+ - bias-pull-pin-default: use pin-default pull state, except the OSCIO pin
+ - drive-push-pull: drive actively high and low
+ - drive-open-drain: drive with open drain only for sx1508q and sx1509q and except the OSCIO pin
+ - output-low: set the pin to output mode with low level
+ - output-high: set the pin to output mode with high level
+
+Example:
+
+	i2c0gpio-expander@20{
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+		compatible = "semtech,sx1506q";
+		reg = <0x20>;
+		interrupt-parent = <&gpio_1>;
+		interrupts = <16 0>;
+
+		gpio-controller;
+		interrupt-controller;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio1_cfg_pins>;
+
+		gpio1_cfg_pins: gpio1-cfg {
+			pins = "gpio1";
+			bias-pull-up;
+		};
+	};