diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/IPMI.txt | 5 | ||||
| -rw-r--r-- | Documentation/acpi/enumeration.txt | 2 | ||||
| -rw-r--r-- | Documentation/acpi/gpio-properties.txt | 6 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/arm/omap/l3-noc.txt | 1 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/clock/silabs,si5351.txt | 4 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt | 2 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt (renamed from Documentation/devicetree/bindings/mtd/m25p80.txt) | 6 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/rtc/abracon,abx80x.txt | 30 | ||||
| -rw-r--r-- | Documentation/kasan.txt | 8 | ||||
| -rw-r--r-- | Documentation/serial/tty.txt | 3 |
10 files changed, 54 insertions, 13 deletions
diff --git a/Documentation/IPMI.txt b/Documentation/IPMI.txt index 653d5d739d7f..31d1d658827f 100644 --- a/Documentation/IPMI.txt +++ b/Documentation/IPMI.txt @@ -505,7 +505,10 @@ at module load time (for a module) with: The addresses are normal I2C addresses. The adapter is the string name of the adapter, as shown in /sys/class/i2c-adapter/i2c-<n>/name. -It is *NOT* i2c-<n> itself. +It is *NOT* i2c-<n> itself. Also, the comparison is done ignoring +spaces, so if the name is "This is an I2C chip" you can say +adapter_name=ThisisanI2cchip. This is because it's hard to pass in +spaces in kernel parameters. The debug flags are bit flags for each BMC found, they are: IPMI messages: 1, driver state: 2, timing: 4, I2C probe: 8 diff --git a/Documentation/acpi/enumeration.txt b/Documentation/acpi/enumeration.txt index 750401f91341..15dfce708ebf 100644 --- a/Documentation/acpi/enumeration.txt +++ b/Documentation/acpi/enumeration.txt @@ -253,7 +253,7 @@ input driver: GPIO support ~~~~~~~~~~~~ ACPI 5 introduced two new resources to describe GPIO connections: GpioIo -and GpioInt. These resources are used be used to pass GPIO numbers used by +and GpioInt. These resources can be used to pass GPIO numbers used by the device to the driver. ACPI 5.1 extended this with _DSD (Device Specific Data) which made it possible to name the GPIOs among other things. diff --git a/Documentation/acpi/gpio-properties.txt b/Documentation/acpi/gpio-properties.txt index ae36fcf86dc7..f35dad11f0de 100644 --- a/Documentation/acpi/gpio-properties.txt +++ b/Documentation/acpi/gpio-properties.txt @@ -1,9 +1,9 @@ _DSD Device Properties Related to GPIO -------------------------------------- -With the release of ACPI 5.1 and the _DSD configuration objecte names -can finally be given to GPIOs (and other things as well) returned by -_CRS. Previously, we were only able to use an integer index to find +With the release of ACPI 5.1, the _DSD configuration object finally +allows names to be given to GPIOs (and other things as well) returned +by _CRS. Previously, we were only able to use an integer index to find the corresponding GPIO, which is pretty error prone (it depends on the _CRS output ordering, for example). diff --git a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt index 974624ea68f6..161448da959d 100644 --- a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt +++ b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt @@ -6,6 +6,7 @@ provided by Arteris. Required properties: - compatible : Should be "ti,omap3-l3-smx" for OMAP3 family Should be "ti,omap4-l3-noc" for OMAP4 family + Should be "ti,omap5-l3-noc" for OMAP5 family Should be "ti,dra7-l3-noc" for DRA7 family Should be "ti,am4372-l3-noc" for AM43 family - reg: Contains L3 register address range for each noc domain. diff --git a/Documentation/devicetree/bindings/clock/silabs,si5351.txt b/Documentation/devicetree/bindings/clock/silabs,si5351.txt index c40711e8e8f7..28b28309f535 100644 --- a/Documentation/devicetree/bindings/clock/silabs,si5351.txt +++ b/Documentation/devicetree/bindings/clock/silabs,si5351.txt @@ -17,7 +17,8 @@ Required properties: - #clock-cells: from common clock binding; shall be set to 1. - clocks: from common clock binding; list of parent clock handles, shall be xtal reference clock or xtal and clkin for - si5351c only. + si5351c only. Corresponding clock input names are "xtal" and + "clkin" respectively. - #address-cells: shall be set to 1. - #size-cells: shall be set to 0. @@ -71,6 +72,7 @@ i2c-master-node { /* connect xtal input to 25MHz reference */ clocks = <&ref25>; + clock-names = "xtal"; /* connect xtal input as source of pll0 and pll1 */ silabs,pll-source = <0 0>, <1 0>; diff --git a/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt b/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt index a4873e5e3e36..e30e184f50c7 100644 --- a/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt +++ b/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt @@ -38,7 +38,7 @@ dma_apbx: dma-apbx@80024000 { 80 81 68 69 70 71 72 73 74 75 76 77>; - interrupt-names = "auart4-rx", "aurat4-tx", "spdif-tx", "empty", + interrupt-names = "auart4-rx", "auart4-tx", "spdif-tx", "empty", "saif0", "saif1", "i2c0", "i2c1", "auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx", "auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx"; diff --git a/Documentation/devicetree/bindings/mtd/m25p80.txt b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt index f20b111b502a..2bee68103b01 100644 --- a/Documentation/devicetree/bindings/mtd/m25p80.txt +++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt @@ -8,8 +8,8 @@ Required properties: is not Linux-only, but in case of Linux, see the "m25p_ids" table in drivers/mtd/devices/m25p80.c for the list of supported chips. - Must also include "nor-jedec" for any SPI NOR flash that can be - identified by the JEDEC READ ID opcode (0x9F). + Must also include "jedec,spi-nor" for any SPI NOR flash that can + be identified by the JEDEC READ ID opcode (0x9F). - reg : Chip-Select number - spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at @@ -25,7 +25,7 @@ Example: flash: m25p80@0 { #address-cells = <1>; #size-cells = <1>; - compatible = "spansion,m25p80", "nor-jedec"; + compatible = "spansion,m25p80", "jedec,spi-nor"; reg = <0>; spi-max-frequency = <40000000>; m25p,fast-read; diff --git a/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt b/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt new file mode 100644 index 000000000000..be789685a1c2 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt @@ -0,0 +1,30 @@ +Abracon ABX80X I2C ultra low power RTC/Alarm chip + +The Abracon ABX80X family consist of the ab0801, ab0803, ab0804, ab0805, ab1801, +ab1803, ab1804 and ab1805. The ab0805 is the superset of ab080x and the ab1805 +is the superset of ab180x. + +Required properties: + + - "compatible": should one of: + "abracon,abx80x" + "abracon,ab0801" + "abracon,ab0803" + "abracon,ab0804" + "abracon,ab0805" + "abracon,ab1801" + "abracon,ab1803" + "abracon,ab1804" + "abracon,ab1805" + Using "abracon,abx80x" will enable chip autodetection. + - "reg": I2C bus address of the device + +Optional properties: + +The abx804 and abx805 have a trickle charger that is able to charge the +connected battery or supercap. Both the following properties have to be defined +and valid to enable charging: + + - "abracon,tc-diode": should be "standard" (0.6V) or "schottky" (0.3V) + - "abracon,tc-resistor": should be <0>, <3>, <6> or <11>. 0 disables the output + resistor, the other values are in ohm. diff --git a/Documentation/kasan.txt b/Documentation/kasan.txt index 092fc10961fe..4692241789b1 100644 --- a/Documentation/kasan.txt +++ b/Documentation/kasan.txt @@ -9,7 +9,9 @@ a fast and comprehensive solution for finding use-after-free and out-of-bounds bugs. KASan uses compile-time instrumentation for checking every memory access, -therefore you will need a certain version of GCC > 4.9.2 +therefore you will need a gcc version of 4.9.2 or later. KASan could detect out +of bounds accesses to stack or global variables, but only if gcc 5.0 or later was +used to built the kernel. Currently KASan is supported only for x86_64 architecture and requires that the kernel be built with the SLUB allocator. @@ -23,8 +25,8 @@ To enable KASAN configure kernel with: and choose between CONFIG_KASAN_OUTLINE and CONFIG_KASAN_INLINE. Outline/inline is compiler instrumentation types. The former produces smaller binary the -latter is 1.1 - 2 times faster. Inline instrumentation requires GCC 5.0 or -latter. +latter is 1.1 - 2 times faster. Inline instrumentation requires a gcc version +of 5.0 or later. Currently KASAN works only with the SLUB memory allocator. For better bug detection and nicer report, enable CONFIG_STACKTRACE and put diff --git a/Documentation/serial/tty.txt b/Documentation/serial/tty.txt index 1e52d67d0abf..dbe6623fed1c 100644 --- a/Documentation/serial/tty.txt +++ b/Documentation/serial/tty.txt @@ -198,6 +198,9 @@ TTY_IO_ERROR If set, causes all subsequent userspace read/write TTY_OTHER_CLOSED Device is a pty and the other side has closed. +TTY_OTHER_DONE Device is a pty and the other side has closed and + all pending input processing has been completed. + TTY_NO_WRITE_SPLIT Prevent driver from splitting up writes into smaller chunks. |