diff options
Diffstat (limited to 'Documentation')
55 files changed, 1137 insertions, 244 deletions
diff --git a/Documentation/ABI/stable/sysfs-bus-usb b/Documentation/ABI/stable/sysfs-bus-usb new file mode 100644 index 000000000000..2be603c52a24 --- /dev/null +++ b/Documentation/ABI/stable/sysfs-bus-usb @@ -0,0 +1,142 @@ +What: /sys/bus/usb/devices/.../power/persist +Date: May 2007 +KernelVersion: 2.6.23 +Contact: Alan Stern <stern@rowland.harvard.edu> +Description: + If CONFIG_USB_PERSIST is set, then each USB device directory + will contain a file named power/persist. The file holds a + boolean value (0 or 1) indicating whether or not the + "USB-Persist" facility is enabled for the device. Since the + facility is inherently dangerous, it is disabled by default + for all devices except hubs. For more information, see + Documentation/usb/persist.txt. + +What: /sys/bus/usb/devices/.../power/autosuspend +Date: March 2007 +KernelVersion: 2.6.21 +Contact: Alan Stern <stern@rowland.harvard.edu> +Description: + Each USB device directory will contain a file named + power/autosuspend. This file holds the time (in seconds) + the device must be idle before it will be autosuspended. + 0 means the device will be autosuspended as soon as + possible. Negative values will prevent the device from + being autosuspended at all, and writing a negative value + will resume the device if it is already suspended. + + The autosuspend delay for newly-created devices is set to + the value of the usbcore.autosuspend module parameter. + +What: /sys/bus/usb/device/.../power/connected_duration +Date: January 2008 +KernelVersion: 2.6.25 +Contact: Sarah Sharp <sarah.a.sharp@intel.com> +Description: + If CONFIG_PM_RUNTIME is enabled then this file + is present. When read, it returns the total time (in msec) + that the USB device has been connected to the machine. This + file is read-only. +Users: + PowerTOP <power@bughost.org> + http://www.lesswatts.org/projects/powertop/ + +What: /sys/bus/usb/device/.../power/active_duration +Date: January 2008 +KernelVersion: 2.6.25 +Contact: Sarah Sharp <sarah.a.sharp@intel.com> +Description: + If CONFIG_PM_RUNTIME is enabled then this file + is present. When read, it returns the total time (in msec) + that the USB device has been active, i.e. not in a suspended + state. This file is read-only. + + Tools can use this file and the connected_duration file to + compute the percentage of time that a device has been active. + For example, + echo $((100 * `cat active_duration` / `cat connected_duration`)) + will give an integer percentage. Note that this does not + account for counter wrap. +Users: + PowerTOP <power@bughost.org> + http://www.lesswatts.org/projects/powertop/ + +What: /sys/bus/usb/devices/<busnum>-<port[.port]>...:<config num>-<interface num>/supports_autosuspend +Date: January 2008 +KernelVersion: 2.6.27 +Contact: Sarah Sharp <sarah.a.sharp@intel.com> +Description: + When read, this file returns 1 if the interface driver + for this interface supports autosuspend. It also + returns 1 if no driver has claimed this interface, as an + unclaimed interface will not stop the device from being + autosuspended if all other interface drivers are idle. + The file returns 0 if autosuspend support has not been + added to the driver. +Users: + USB PM tool + git://git.moblin.org/users/sarah/usb-pm-tool/ + +What: /sys/bus/usb/device/.../avoid_reset_quirk +Date: December 2009 +Contact: Oliver Neukum <oliver@neukum.org> +Description: + Writing 1 to this file tells the kernel that this + device will morph into another mode when it is reset. + Drivers will not use reset for error handling for + such devices. +Users: + usb_modeswitch + +What: /sys/bus/usb/devices/.../devnum +KernelVersion: since at least 2.6.18 +Description: + Device address on the USB bus. +Users: + libusb + +What: /sys/bus/usb/devices/.../bConfigurationValue +KernelVersion: since at least 2.6.18 +Description: + bConfigurationValue of the *active* configuration for the + device. Writing 0 or -1 to bConfigurationValue will reset the + active configuration (unconfigure the device). Writing + another value will change the active configuration. + + Note that some devices, in violation of the USB spec, have a + configuration with a value equal to 0. Writing 0 to + bConfigurationValue for these devices will install that + configuration, rather then unconfigure the device. + + Writing -1 will always unconfigure the device. +Users: + libusb + +What: /sys/bus/usb/devices/.../busnum +KernelVersion: 2.6.22 +Description: + Bus-number of the USB-bus the device is connected to. +Users: + libusb + +What: /sys/bus/usb/devices/.../descriptors +KernelVersion: 2.6.26 +Description: + Binary file containing cached descriptors of the device. The + binary data consists of the device descriptor followed by the + descriptors for each configuration of the device. + Note that the wTotalLength of the config descriptors can not + be trusted, as the device may have a smaller config descriptor + than it advertises. The bLength field of each (sub) descriptor + can be trusted, and can be used to seek forward one (sub) + descriptor at a time until the next config descriptor is found. + All descriptors read from this file are in bus-endian format +Users: + libusb + +What: /sys/bus/usb/devices/.../speed +KernelVersion: since at least 2.6.18 +Description: + Speed the device is connected with to the usb-host in + Mbit / second. IE one of 1.5 / 12 / 480 / 5000. +Users: + libusb diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio index dda81ffae5cf..39c8de0e53d0 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio +++ b/Documentation/ABI/testing/sysfs-bus-iio @@ -351,6 +351,7 @@ Description: 6kohm_to_gnd: connected to ground via a 6kOhm resistor, 20kohm_to_gnd: connected to ground via a 20kOhm resistor, 100kohm_to_gnd: connected to ground via an 100kOhm resistor, + 500kohm_to_gnd: connected to ground via a 500kOhm resistor, three_state: left floating. For a list of available output power down options read outX_powerdown_mode_available. If Y is not present the @@ -792,3 +793,21 @@ Contact: linux-iio@vger.kernel.org Description: This attribute is used to read the amount of quadrature error present in the device at a given time. + +What: /sys/.../iio:deviceX/in_accelX_power_mode +KernelVersion: 3.11 +Contact: linux-iio@vger.kernel.org +Description: + Specifies the chip power mode. + low_noise: reduce noise level from ADC, + low_power: enable low current consumption. + For a list of available output power modes read + in_accel_power_mode_available. + +What: /sys/bus/iio/devices/iio:deviceX/store_eeprom +KernelVersion: 3.4.0 +Contact: linux-iio@vger.kernel.org +Description: + Writing '1' stores the current device configuration into + on-chip EEPROM. After power-up or chip reset the device will + automatically load the saved configuration. diff --git a/Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523 b/Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523 index 2ce9c3f68eee..a91aeabe7b24 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523 +++ b/Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523 @@ -18,14 +18,6 @@ Description: Reading returns either '1' or '0'. '1' means that the pllY is locked. -What: /sys/bus/iio/devices/iio:deviceX/store_eeprom -KernelVersion: 3.4.0 -Contact: linux-iio@vger.kernel.org -Description: - Writing '1' stores the current device configuration into - on-chip EEPROM. After power-up or chip reset the device will - automatically load the saved configuration. - What: /sys/bus/iio/devices/iio:deviceX/sync_dividers KernelVersion: 3.4.0 Contact: linux-iio@vger.kernel.org diff --git a/Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350 b/Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350 index d89aded01c5a..1254457a726e 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350 +++ b/Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350 @@ -18,4 +18,4 @@ Description: adjust the reference frequency accordingly. The value written has no effect until out_altvoltageY_frequency is updated. Consider to use out_altvoltageY_powerdown to power - down the PLL and it's RFOut buffers during REFin changes. + down the PLL and its RFOut buffers during REFin changes. diff --git a/Documentation/ABI/testing/sysfs-bus-usb b/Documentation/ABI/testing/sysfs-bus-usb index 9759b8c91332..1430f584b266 100644 --- a/Documentation/ABI/testing/sysfs-bus-usb +++ b/Documentation/ABI/testing/sysfs-bus-usb @@ -1,81 +1,3 @@ -What: /sys/bus/usb/devices/.../power/autosuspend -Date: March 2007 -KernelVersion: 2.6.21 -Contact: Alan Stern <stern@rowland.harvard.edu> -Description: - Each USB device directory will contain a file named - power/autosuspend. This file holds the time (in seconds) - the device must be idle before it will be autosuspended. - 0 means the device will be autosuspended as soon as - possible. Negative values will prevent the device from - being autosuspended at all, and writing a negative value - will resume the device if it is already suspended. - - The autosuspend delay for newly-created devices is set to - the value of the usbcore.autosuspend module parameter. - -What: /sys/bus/usb/devices/.../power/persist -Date: May 2007 -KernelVersion: 2.6.23 -Contact: Alan Stern <stern@rowland.harvard.edu> -Description: - If CONFIG_USB_PERSIST is set, then each USB device directory - will contain a file named power/persist. The file holds a - boolean value (0 or 1) indicating whether or not the - "USB-Persist" facility is enabled for the device. Since the - facility is inherently dangerous, it is disabled by default - for all devices except hubs. For more information, see - Documentation/usb/persist.txt. - -What: /sys/bus/usb/device/.../power/connected_duration -Date: January 2008 -KernelVersion: 2.6.25 -Contact: Sarah Sharp <sarah.a.sharp@intel.com> -Description: - If CONFIG_PM_RUNTIME is enabled then this file - is present. When read, it returns the total time (in msec) - that the USB device has been connected to the machine. This - file is read-only. -Users: - PowerTOP <power@bughost.org> - http://www.lesswatts.org/projects/powertop/ - -What: /sys/bus/usb/device/.../power/active_duration -Date: January 2008 -KernelVersion: 2.6.25 -Contact: Sarah Sharp <sarah.a.sharp@intel.com> -Description: - If CONFIG_PM_RUNTIME is enabled then this file - is present. When read, it returns the total time (in msec) - that the USB device has been active, i.e. not in a suspended - state. This file is read-only. - - Tools can use this file and the connected_duration file to - compute the percentage of time that a device has been active. - For example, - echo $((100 * `cat active_duration` / `cat connected_duration`)) - will give an integer percentage. Note that this does not - account for counter wrap. -Users: - PowerTOP <power@bughost.org> - http://www.lesswatts.org/projects/powertop/ - -What: /sys/bus/usb/device/<busnum>-<devnum>...:<config num>-<interface num>/supports_autosuspend -Date: January 2008 -KernelVersion: 2.6.27 -Contact: Sarah Sharp <sarah.a.sharp@intel.com> -Description: - When read, this file returns 1 if the interface driver - for this interface supports autosuspend. It also - returns 1 if no driver has claimed this interface, as an - unclaimed interface will not stop the device from being - autosuspended if all other interface drivers are idle. - The file returns 0 if autosuspend support has not been - added to the driver. -Users: - USB PM tool - git://git.moblin.org/users/sarah/usb-pm-tool/ - What: /sys/bus/usb/device/.../authorized Date: July 2008 KernelVersion: 2.6.26 @@ -172,17 +94,6 @@ Description: device IDs, exactly like reading from the entry "/sys/bus/usb/drivers/.../new_id" -What: /sys/bus/usb/device/.../avoid_reset_quirk -Date: December 2009 -Contact: Oliver Neukum <oliver@neukum.org> -Description: - Writing 1 to this file tells the kernel that this - device will morph into another mode when it is reset. - Drivers will not use reset for error handling for - such devices. -Users: - usb_modeswitch - What: /sys/bus/usb/devices/.../power/usb2_hardware_lpm Date: September 2011 Contact: Andiry Xu <andiry.xu@amd.com> diff --git a/Documentation/devicetree/bindings/arm/atmel-adc.txt b/Documentation/devicetree/bindings/arm/atmel-adc.txt index 16769d9cedd6..723c205cb10d 100644 --- a/Documentation/devicetree/bindings/arm/atmel-adc.txt +++ b/Documentation/devicetree/bindings/arm/atmel-adc.txt @@ -1,18 +1,15 @@ * AT91's Analog to Digital Converter (ADC) Required properties: - - compatible: Should be "atmel,at91sam9260-adc" + - compatible: Should be "atmel,<chip>-adc" + <chip> can be "at91sam9260", "at91sam9g45" or "at91sam9x5" - reg: Should contain ADC registers location and length - interrupts: Should contain the IRQ line for the ADC - - atmel,adc-channel-base: Offset of the first channel data register - atmel,adc-channels-used: Bitmask of the channels muxed and enable for this device - - atmel,adc-drdy-mask: Mask of the DRDY interruption in the ADC - atmel,adc-num-channels: Number of channels available in the ADC - atmel,adc-startup-time: Startup Time of the ADC in microseconds as defined in the datasheet - - atmel,adc-status-register: Offset of the Interrupt Status Register - - atmel,adc-trigger-register: Offset of the Trigger Register - atmel,adc-vref: Reference voltage in millivolts for the conversions - atmel,adc-res: List of resolution in bits supported by the ADC. List size must be two at least. diff --git a/Documentation/devicetree/bindings/extcon/extcon-twl.txt b/Documentation/devicetree/bindings/extcon/extcon-palmas.txt index 58f531ab4df3..7dab6a8f4a0e 100644 --- a/Documentation/devicetree/bindings/extcon/extcon-twl.txt +++ b/Documentation/devicetree/bindings/extcon/extcon-palmas.txt @@ -1,15 +1,15 @@ -EXTCON FOR TWL CHIPS +EXTCON FOR PALMAS/TWL CHIPS PALMAS USB COMPARATOR Required Properties: - compatible : Should be "ti,palmas-usb" or "ti,twl6035-usb" - - vbus-supply : phandle to the regulator device tree node. Optional Properties: - ti,wakeup : To enable the wakeup comparator in probe + - ti,enable-id-detection: Perform ID detection. + - ti,enable-vbus-detection: Perform VBUS detection. palmas-usb { compatible = "ti,twl6035-usb", "ti,palmas-usb"; - vbus-supply = <&smps10_reg>; ti,wakeup; }; diff --git a/Documentation/devicetree/bindings/iio/accel/bma180.txt b/Documentation/devicetree/bindings/iio/accel/bma180.txt new file mode 100644 index 000000000000..c5933573e0f6 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/bma180.txt @@ -0,0 +1,24 @@ +* Bosch BMA180 triaxial acceleration sensor + +http://omapworld.com/BMA180_111_1002839.pdf + +Required properties: + + - compatible : should be "bosch,bma180" + - reg : the I2C address of the sensor + +Optional properties: + + - interrupt-parent : should be the phandle for the interrupt controller + + - interrupts : interrupt mapping for GPIO IRQ, it should by configured with + flags IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING + +Example: + +bma180@40 { + compatible = "bosch,bma180"; + reg = <0x40>; + interrupt-parent = <&gpio6>; + interrupts = <18 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/nuvoton-nau7802.txt b/Documentation/devicetree/bindings/iio/adc/nuvoton-nau7802.txt new file mode 100644 index 000000000000..e9582e6fe350 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/nuvoton-nau7802.txt @@ -0,0 +1,18 @@ +* Nuvoton NAU7802 Analog to Digital Converter (ADC) + +Required properties: + - compatible: Should be "nuvoton,nau7802" + - reg: Should contain the ADC I2C address + +Optional properties: + - nuvoton,vldo: Internal reference voltage in millivolts to be + configured valid values are between 2400 mV and 4500 mV. + - interrupts: IRQ line for the ADC. If not used the driver will use + polling. + +Example: +adc2: nau7802@2a { + compatible = "nuvoton,nau7802"; + reg = <0x2a>; + nuvoton,vldo = <3000>; +}; diff --git a/Documentation/devicetree/bindings/iio/light/apds9300.txt b/Documentation/devicetree/bindings/iio/light/apds9300.txt new file mode 100644 index 000000000000..d6f66c73ddbf --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/apds9300.txt @@ -0,0 +1,22 @@ +* Avago APDS9300 ambient light sensor + +http://www.avagotech.com/docs/AV02-1077EN + +Required properties: + + - compatible : should be "avago,apds9300" + - reg : the I2C address of the sensor + +Optional properties: + + - interrupt-parent : should be the phandle for the interrupt controller + - interrupts : interrupt mapping for GPIO IRQ + +Example: + +apds9300@39 { + compatible = "avago,apds9300"; + reg = <0x39>; + interrupt-parent = <&gpio2>; + interrupts = <29 8>; +}; diff --git a/Documentation/devicetree/bindings/regulator/88pm800.txt b/Documentation/devicetree/bindings/regulator/88pm800.txt new file mode 100644 index 000000000000..e8a54c2a5821 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/88pm800.txt @@ -0,0 +1,38 @@ +Marvell 88PM800 regulator + +Required properties: +- compatible: "marvell,88pm800" +- reg: I2C slave address +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name (or the deprecated + regulator-compatible property if present), with valid values listed below. + The content of each sub-node is defined by the standard binding for + regulators; see regulator.txt. + +The valid names for regulators are: + + buck1, buck2, buck3, buck4, buck5, ldo1, ldo2, ldo3, ldo4, ldo5, ldo6, ldo7, + ldo8, ldo9, ldo10, ldo11, ldo12, ldo13, ldo14, ldo15, ldo16, ldo17, ldo18, ldo19 + +Example: + + pmic: 88pm800@31 { + compatible = "marvell,88pm800"; + reg = <0x31>; + + regulators { + buck1 { + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3950000>; + regulator-boot-on; + regulator-always-on; + }; + ldo1 { + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <15000000>; + regulator-boot-on; + regulator-always-on; + }; +... + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/max8660.txt b/Documentation/devicetree/bindings/regulator/max8660.txt new file mode 100644 index 000000000000..8ba994d8a142 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max8660.txt @@ -0,0 +1,47 @@ +Maxim MAX8660 voltage regulator + +Required properties: +- compatible: must be one of "maxim,max8660", "maxim,max8661" +- reg: I2C slave address, usually 0x34 +- any required generic properties defined in regulator.txt + +Example: + + i2c_master { + max8660@34 { + compatible = "maxim,max8660"; + reg = <0x34>; + + regulators { + regulator@0 { + regulator-compatible= "V3(DCDC)"; + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <1800000>; + }; + + regulator@1 { + regulator-compatible= "V4(DCDC)"; + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <1800000>; + }; + + regulator@2 { + regulator-compatible= "V5(LDO)"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <2000000>; + }; + + regulator@3 { + regulator-compatible= "V6(LDO)"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + regulator@4 { + regulator-compatible= "V7(LDO)"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/palmas-pmic.txt b/Documentation/devicetree/bindings/regulator/palmas-pmic.txt index 30b0581bb1ce..a22e4c70db5c 100644 --- a/Documentation/devicetree/bindings/regulator/palmas-pmic.txt +++ b/Documentation/devicetree/bindings/regulator/palmas-pmic.txt @@ -25,8 +25,8 @@ Optional nodes: Additional custom properties are listed below. For ti,palmas-pmic - smps12, smps123, smps3 depending on OTP, - smps45, smps457, smps7 depending on variant, smps6, smps[8-10], - ldo[1-9], ldoln, ldousb. + smps45, smps457, smps7 depending on variant, smps6, smps[8-9], + smps10_out2, smps10_out1, do[1-9], ldoln, ldousb. Optional sub-node properties: ti,warm-reset - maintain voltage during warm reset(boolean) diff --git a/Documentation/devicetree/bindings/regulator/pfuze100.txt b/Documentation/devicetree/bindings/regulator/pfuze100.txt new file mode 100644 index 000000000000..fc989b2e8057 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/pfuze100.txt @@ -0,0 +1,115 @@ +PFUZE100 family of regulators + +Required properties: +- compatible: "fsl,pfuze100" +- reg: I2C slave address + +Required child node: +- regulators: This is the list of child nodes that specify the regulator + initialization data for defined regulators. Please refer to below doc + Documentation/devicetree/bindings/regulator/regulator.txt. + + The valid names for regulators are: + sw1ab,sw1c,sw2,sw3a,sw3b,sw4,swbst,vsnvs,vrefddr,vgen1~vgen6 + +Each regulator is defined using the standard binding for regulators. + +Example: + + pmic: pfuze100@08 { + compatible = "fsl,pfuze100"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1ab { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw1c_reg: sw1c { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3a { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3b_reg: sw3b { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen2_reg: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen3_reg: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + vgen4_reg: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 48a3b8e5d6bd..2bd8f0978765 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -12,6 +12,8 @@ Optional properties: - regulator-allow-bypass: allow the regulator to go into bypass mode - <name>-supply: phandle to the parent supply/regulator node - regulator-ramp-delay: ramp delay for regulator(in uV/uS) + For hardwares which support disabling ramp rate, it should be explicitly + intialised to zero (regulator-ramp-delay = <0>) for disabling ramp delay. Deprecated properties: - regulator-compatible: If a regulator chip contains multiple diff --git a/Documentation/devicetree/bindings/tty/serial/arc-uart.txt b/Documentation/devicetree/bindings/serial/arc-uart.txt index 5cae2eb686f8..5cae2eb686f8 100644 --- a/Documentation/devicetree/bindings/tty/serial/arc-uart.txt +++ b/Documentation/devicetree/bindings/serial/arc-uart.txt diff --git a/Documentation/devicetree/bindings/tty/serial/atmel-usart.txt b/Documentation/devicetree/bindings/serial/atmel-usart.txt index a49d9a1d4ccf..2191dcb9f1da 100644 --- a/Documentation/devicetree/bindings/tty/serial/atmel-usart.txt +++ b/Documentation/devicetree/bindings/serial/atmel-usart.txt @@ -10,13 +10,18 @@ Required properties: Optional properties: - atmel,use-dma-rx: use of PDC or DMA for receiving data - atmel,use-dma-tx: use of PDC or DMA for transmitting data +- add dma bindings for dma transfer: + - dmas: DMA specifier, consisting of a phandle to DMA controller node, + memory peripheral interface and USART DMA channel ID, FIFO configuration. + Refer to dma.txt and atmel-dma.txt for details. + - dma-names: "rx" for RX channel, "tx" for TX channel. <chip> compatible description: - at91rm9200: legacy USART support - at91sam9260: generic USART implementation for SAM9 SoCs Example: - +- use PDC: usart0: serial@fff8c000 { compatible = "atmel,at91sam9260-usart"; reg = <0xfff8c000 0x4000>; @@ -25,3 +30,14 @@ Example: atmel,use-dma-tx; }; +- use DMA: + usart0: serial@f001c000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xf001c000 0x100>; + interrupts = <12 4 5>; + atmel,use-dma-rx; + atmel,use-dma-tx; + dmas = <&dma0 2 0x3>, + <&dma0 2 0x204>; + dma-names = "tx", "rx"; + }; diff --git a/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt b/Documentation/devicetree/bindings/serial/efm32-uart.txt index 8e080b893b49..8e080b893b49 100644 --- a/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt +++ b/Documentation/devicetree/bindings/serial/efm32-uart.txt diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt index c58573b5b1a4..35ae1fb3537f 100644 --- a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt +++ b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt @@ -1,35 +1,29 @@ -* Freescale i.MX UART controller +* Freescale i.MX Universal Asynchronous Receiver/Transmitter (UART) Required properties: -- compatible : should be "fsl,imx21-uart" +- compatible : Should be "fsl,<soc>-uart" - reg : Address and length of the register set for the device -- interrupts : Should contain UART interrupt number +- interrupts : Should contain uart interrupt Optional properties: -- fsl,uart-has-rtscts: indicate that RTS/CTS signals are used +- fsl,uart-has-rtscts : Indicate the uart has rts and cts +- fsl,irda-mode : Indicate the uart supports irda mode +- fsl,dte-mode : Indicate the uart works in DTE mode. The uart works + is DCE mode by default. Note: Each uart controller should have an alias correctly numbered in "aliases" node. Example: -- From imx51.dtsi: aliases { serial0 = &uart1; - serial1 = &uart2; - serial2 = &uart3; }; uart1: serial@73fbc000 { compatible = "fsl,imx51-uart", "fsl,imx21-uart"; reg = <0x73fbc000 0x4000>; interrupts = <31>; - status = "disabled"; -} - -- From imx51-babbage.dts: -uart1: serial@73fbc000 { fsl,uart-has-rtscts; - status = "okay"; + fsl,dte-mode; }; - diff --git a/Documentation/devicetree/bindings/tty/serial/fsl-lpuart.txt b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt index 6fd1dd1638dd..6fd1dd1638dd 100644 --- a/Documentation/devicetree/bindings/tty/serial/fsl-lpuart.txt +++ b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt diff --git a/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt b/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt index 2c00ec64628e..59a40f18d551 100644 --- a/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt +++ b/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt @@ -10,6 +10,10 @@ Required properties: Refer to dma.txt and fsl-mxs-dma.txt for details. - dma-names: "rx" for RX channel, "tx" for TX channel. +Optional properties: +- fsl,uart-has-rtscts : Indicate the UART has RTS and CTS lines, + it also means you enable the DMA support for this UART. + Example: auart0: serial@8006a000 { compatible = "fsl,imx28-auart", "fsl,imx23-auart"; diff --git a/Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt b/Documentation/devicetree/bindings/serial/nxp-lpc32xx-hsuart.txt index 0d439dfc1aa5..0d439dfc1aa5 100644 --- a/Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt +++ b/Documentation/devicetree/bindings/serial/nxp-lpc32xx-hsuart.txt diff --git a/Documentation/devicetree/bindings/tty/serial/of-serial.txt b/Documentation/devicetree/bindings/serial/of-serial.txt index 1928a3e83cd0..1928a3e83cd0 100644 --- a/Documentation/devicetree/bindings/tty/serial/of-serial.txt +++ b/Documentation/devicetree/bindings/serial/of-serial.txt diff --git a/Documentation/devicetree/bindings/serial/qcom,msm-uart.txt b/Documentation/devicetree/bindings/serial/qcom,msm-uart.txt new file mode 100644 index 000000000000..ce8c90161959 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/qcom,msm-uart.txt @@ -0,0 +1,25 @@ +* MSM Serial UART + +The MSM serial UART hardware is designed for low-speed use cases where a +dma-engine isn't needed. From a software perspective it's mostly compatible +with the MSM serial UARTDM except that it only supports reading and writing one +character at a time. + +Required properties: +- compatible: Should contain "qcom,msm-uart" +- reg: Should contain UART register location and length. +- interrupts: Should contain UART interrupt. +- clocks: Should contain the core clock. +- clock-names: Should be "core". + +Example: + +A uart device at 0xa9c00000 with interrupt 11. + +serial@a9c00000 { + compatible = "qcom,msm-uart"; + reg = <0xa9c00000 0x1000>; + interrupts = <11>; + clocks = <&uart_cxc>; + clock-names = "core"; +}; diff --git a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt new file mode 100644 index 000000000000..ffa5b784c66e --- /dev/null +++ b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt @@ -0,0 +1,53 @@ +* MSM Serial UARTDM + +The MSM serial UARTDM hardware is designed for high-speed use cases where the +transmit and/or receive channels can be offloaded to a dma-engine. From a +software perspective it's mostly compatible with the MSM serial UART except +that it supports reading and writing multiple characters at a time. + +Required properties: +- compatible: Should contain at least "qcom,msm-uartdm". + A more specific property should be specified as follows depending + on the version: + "qcom,msm-uartdm-v1.1" + "qcom,msm-uartdm-v1.2" + "qcom,msm-uartdm-v1.3" + "qcom,msm-uartdm-v1.4" +- reg: Should contain UART register locations and lengths. The first + register shall specify the main control registers. An optional second + register location shall specify the GSBI control region. + "qcom,msm-uartdm-v1.3" is the only compatible value that might + need the GSBI control region. +- interrupts: Should contain UART interrupt. +- clocks: Should contain the core clock and the AHB clock. +- clock-names: Should be "core" for the core clock and "iface" for the + AHB clock. + +Optional properties: +- dmas: Should contain dma specifiers for transmit and receive channels +- dma-names: Should contain "tx" for transmit and "rx" for receive channels + +Examples: + +A uartdm v1.4 device with dma capabilities. + +serial@f991e000 { + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; + reg = <0xf991e000 0x1000>; + interrupts = <0 108 0x0>; + clocks = <&blsp1_uart2_apps_cxc>, <&blsp1_ahb_cxc>; + clock-names = "core", "iface"; + dmas = <&dma0 0>, <&dma0 1>; + dma-names = "tx", "rx"; +}; + +A uartdm v1.3 device without dma capabilities and part of a GSBI complex. + +serial@19c40000 { + compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; + reg = <0x19c40000 0x1000>, + <0x19c00000 0x1000>; + interrupts = <0 195 0x0>; + clocks = <&gsbi5_uart_cxc>, <&gsbi5_ahb_cxc>; + clock-names = "core", "iface"; +}; diff --git a/Documentation/devicetree/bindings/serial/sirf-uart.txt b/Documentation/devicetree/bindings/serial/sirf-uart.txt new file mode 100644 index 000000000000..a2dfc6522a91 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/sirf-uart.txt @@ -0,0 +1,33 @@ +* CSR SiRFprimaII/atlasVI Universal Synchronous Asynchronous Receiver/Transmitter * + +Required properties: +- compatible : Should be "sirf,prima2-uart" or "sirf, prima2-usp-uart" +- reg : Offset and length of the register set for the device +- interrupts : Should contain uart interrupt +- fifosize : Should define hardware rx/tx fifo size +- clocks : Should contain uart clock number + +Optional properties: +- sirf,uart-has-rtscts: we have hardware flow controller pins in hardware +- rts-gpios: RTS pin for USP-based UART if sirf,uart-has-rtscts is true +- cts-gpios: CTS pin for USP-based UART if sirf,uart-has-rtscts is true + +Example: + +uart0: uart@b0050000 { + cell-index = <0>; + compatible = "sirf,prima2-uart"; + reg = <0xb0050000 0x1000>; + interrupts = <17>; + fifosize = <128>; + clocks = <&clks 13>; +}; + +On the board-specific dts, we can put rts-gpios and cts-gpios like + +usp@b0090000 { + compatible = "sirf,prima2-usp-uart"; + sirf,uart-has-rtscts; + rts-gpios = <&gpio 15 0>; + cts-gpios = <&gpio 46 0>; +}; diff --git a/Documentation/devicetree/bindings/tty/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt index f13f1c5be91c..f13f1c5be91c 100644 --- a/Documentation/devicetree/bindings/tty/serial/snps-dw-apb-uart.txt +++ b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt diff --git a/Documentation/devicetree/bindings/serial/st-asc.txt b/Documentation/devicetree/bindings/serial/st-asc.txt new file mode 100644 index 000000000000..75d877f5968f --- /dev/null +++ b/Documentation/devicetree/bindings/serial/st-asc.txt @@ -0,0 +1,18 @@ +*st-asc(Serial Port) + +Required properties: +- compatible : Should be "st,asc". +- reg, reg-names, interrupts, interrupt-names : Standard way to define device + resources with names. look in + Documentation/devicetree/bindings/resource-names.txt + +Optional properties: +- st,hw-flow-ctrl bool flag to enable hardware flow control. +- st,force-m1 bool flat to force asc to be in Mode-1 recommeded + for high bit rates (above 19.2K) +Example: +serial@fe440000{ + compatible = "st,asc"; + reg = <0xfe440000 0x2c>; + interrupts = <0 209 0>; +}; diff --git a/Documentation/devicetree/bindings/tty/serial/via,vt8500-uart.txt b/Documentation/devicetree/bindings/serial/via,vt8500-uart.txt index 5feef1ef167d..5feef1ef167d 100644 --- a/Documentation/devicetree/bindings/tty/serial/via,vt8500-uart.txt +++ b/Documentation/devicetree/bindings/serial/via,vt8500-uart.txt diff --git a/Documentation/devicetree/bindings/spi/efm32-spi.txt b/Documentation/devicetree/bindings/spi/efm32-spi.txt new file mode 100644 index 000000000000..a590ca51be75 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/efm32-spi.txt @@ -0,0 +1,34 @@ +* Energy Micro EFM32 SPI + +Required properties: +- #address-cells: see spi-bus.txt +- #size-cells: see spi-bus.txt +- compatible: should be "efm32,spi" +- reg: Offset and length of the register set for the controller +- interrupts: pair specifying rx and tx irq +- clocks: phandle to the spi clock +- cs-gpios: see spi-bus.txt +- location: Value to write to the ROUTE register's LOCATION bitfield to configure the pinmux for the device, see datasheet for values. + +Example: + +spi1: spi@0x4000c400 { /* USART1 */ + #address-cells = <1>; + #size-cells = <0>; + compatible = "efm32,spi"; + reg = <0x4000c400 0x400>; + interrupts = <15 16>; + clocks = <&cmu 20>; + cs-gpios = <&gpio 51 1>; // D3 + location = <1>; + status = "ok"; + + ks8851@0 { + compatible = "ks8851"; + spi-max-frequency = <6000000>; + reg = <0>; + interrupt-parent = <&boardfpga>; + interrupts = <4>; + status = "ok"; + }; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt index 296015e3c632..800dafe5b01b 100644 --- a/Documentation/devicetree/bindings/spi/spi-bus.txt +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -55,6 +55,16 @@ contain the following properties. chip select active high - spi-3wire - (optional) Empty property indicating device requires 3-wire mode. +- spi-tx-bus-width - (optional) The bus width(number of data wires) that + used for MOSI. Defaults to 1 if not present. +- spi-rx-bus-width - (optional) The bus width(number of data wires) that + used for MISO. Defaults to 1 if not present. + +Some SPI controllers and devices support Dual and Quad SPI transfer mode. +It allows data in SPI system transfered in 2 wires(DUAL) or 4 wires(QUAD). +Now the value that spi-tx-bus-width and spi-rx-bus-width can receive is +only 1(SINGLE), 2(DUAL) and 4(QUAD). +Dual/Quad mode is not allowed when 3-wire mode is used. If a gpio chipselect is used for the SPI slave the gpio number will be passed via the cs_gpio diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt new file mode 100644 index 000000000000..a1fb3035a42b --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt @@ -0,0 +1,42 @@ +ARM Freescale DSPI controller + +Required properties: +- compatible : "fsl,vf610-dspi" +- reg : Offset and length of the register set for the device +- interrupts : Should contain SPI controller interrupt +- clocks: from common clock binding: handle to dspi clock. +- clock-names: from common clock binding: Shall be "dspi". +- pinctrl-0: pin control group to be used for this controller. +- pinctrl-names: must contain a "default" entry. +- spi-num-chipselects : the number of the chipselect signals. +- bus-num : the slave chip chipselect signal number. +Example: + +dspi0@4002c000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,vf610-dspi"; + reg = <0x4002c000 0x1000>; + interrupts = <0 67 0x04>; + clocks = <&clks VF610_CLK_DSPI0>; + clock-names = "dspi"; + spi-num-chipselects = <5>; + bus-num = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dspi0_1>; + status = "okay"; + + sflash: at26df081a@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "atmel,at26df081a"; + spi-max-frequency = <16000000>; + spi-cpol; + spi-cpha; + reg = <0>; + linux,modalias = "m25p80"; + modal = "at26df081a"; + }; +}; + + diff --git a/Documentation/devicetree/bindings/spi/ti_qspi.txt b/Documentation/devicetree/bindings/spi/ti_qspi.txt new file mode 100644 index 000000000000..1f9641ade0b5 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/ti_qspi.txt @@ -0,0 +1,22 @@ +TI QSPI controller. + +Required properties: +- compatible : should be "ti,dra7xxx-qspi" or "ti,am4372-qspi". +- reg: Should contain QSPI registers location and length. +- #address-cells, #size-cells : Must be present if the device has sub-nodes +- ti,hwmods: Name of the hwmod associated to the QSPI + +Recommended properties: +- spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + +qspi: qspi@4b300000 { + compatible = "ti,dra7xxx-qspi"; + reg = <0x4b300000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <25000000>; + ti,hwmods = "qspi"; +}; diff --git a/Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt deleted file mode 100644 index c662eb36be29..000000000000 --- a/Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt +++ /dev/null @@ -1,22 +0,0 @@ -* Freescale i.MX Universal Asynchronous Receiver/Transmitter (UART) - -Required properties: -- compatible : Should be "fsl,<soc>-uart" -- reg : Address and length of the register set for the device -- interrupts : Should contain uart interrupt - -Optional properties: -- fsl,uart-has-rtscts : Indicate the uart has rts and cts -- fsl,irda-mode : Indicate the uart supports irda mode -- fsl,dte-mode : Indicate the uart works in DTE mode. The uart works - is DCE mode by default. - -Example: - -serial@73fbc000 { - compatible = "fsl,imx51-uart", "fsl,imx21-uart"; - reg = <0x73fbc000 0x4000>; - interrupts = <31>; - fsl,uart-has-rtscts; - fsl,dte-mode; -}; diff --git a/Documentation/devicetree/bindings/tty/serial/msm_serial.txt b/Documentation/devicetree/bindings/tty/serial/msm_serial.txt deleted file mode 100644 index aef383eb8876..000000000000 --- a/Documentation/devicetree/bindings/tty/serial/msm_serial.txt +++ /dev/null @@ -1,27 +0,0 @@ -* Qualcomm MSM UART - -Required properties: -- compatible : - - "qcom,msm-uart", and one of "qcom,msm-hsuart" or - "qcom,msm-lsuart". -- reg : offset and length of the register set for the device - for the hsuart operating in compatible mode, there should be a - second pair describing the gsbi registers. -- interrupts : should contain the uart interrupt. - -There are two different UART blocks used in MSM devices, -"qcom,msm-hsuart" and "qcom,msm-lsuart". The msm-serial driver is -able to handle both of these, and matches against the "qcom,msm-uart" -as the compatibility. - -The registers for the "qcom,msm-hsuart" device need to specify both -register blocks, even for the common driver. - -Example: - - uart@19c400000 { - compatible = "qcom,msm-hsuart", "qcom,msm-uart"; - reg = <0x19c40000 0x1000>, - <0x19c00000 0x1000>; - interrupts = <195>; - }; diff --git a/Documentation/devicetree/bindings/tty/serial/qca,ar9330-uart.txt b/Documentation/devicetree/bindings/tty/serial/qca,ar9330-uart.txt new file mode 100644 index 000000000000..c5e032c85bf9 --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/qca,ar9330-uart.txt @@ -0,0 +1,34 @@ +* Qualcomm Atheros AR9330 High-Speed UART + +Required properties: + +- compatible: Must be "qca,ar9330-uart" + +- reg: Specifies the physical base address of the controller and + the length of the memory mapped region. + +- interrupt-parent: The phandle for the interrupt controller that + services interrupts for this device. + +- interrupts: Specifies the interrupt source of the parent interrupt + controller. The format of the interrupt specifier depends on the + parent interrupt controller. + +Additional requirements: + + Each UART port must have an alias correctly numbered in "aliases" + node. + +Example: + + aliases { + serial0 = &uart0; + }; + + uart0: uart@18020000 { + compatible = "qca,ar9330-uart"; + reg = <0x18020000 0x14>; + + interrupt-parent = <&intc>; + interrupts = <3>; + }; diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt index dc9dc8c87f15..20c2ff2ba07e 100644 --- a/Documentation/devicetree/bindings/usb/am33xx-usb.txt +++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt @@ -1,35 +1,197 @@ -AM33XX MUSB GLUE - - compatible : Should be "ti,musb-am33xx" - - reg : offset and length of register sets, first usbss, then for musb instances - - interrupts : usbss, musb instance interrupts in order - - ti,hwmods : must be "usb_otg_hs" - - multipoint : Should be "1" indicating the musb controller supports - multipoint. This is a MUSB configuration-specific setting. - - num-eps : Specifies the number of endpoints. This is also a - MUSB configuration-specific setting. Should be set to "16" - - ram-bits : Specifies the ram address size. Should be set to "12" - - port0-mode : Should be "3" to represent OTG. "1" signifies HOST and "2" - represents PERIPHERAL. - - port1-mode : Should be "1" to represent HOST. "3" signifies OTG and "2" - represents PERIPHERAL. - - power : Should be "250". This signifies the controller can supply up to - 500mA when operating in host mode. + AM33xx MUSB +~~~~~~~~~~~~~~~ +- compatible: ti,am33xx-usb +- reg: offset and length of the usbss register sets +- ti,hwmods : must be "usb_otg_hs" + +The glue layer contains multiple child nodes. It is required the have +at least a control module node, USB node and a PHY node. The second USB +node and its PHY node is optional. The DMA node is also optional. + +Reset module +~~~~~~~~~~~~ +- compatible: ti,am335x-usb-ctrl-module +- reg: offset and length of the "USB control registers" in the "Control + Module" block. A second offset and length for the USB wake up control + in the same memory block. +- reg-names: "phy_ctrl" for the "USB control registers" and "wakeup" for + the USB wake up control register. + +USB PHY +~~~~~~~ +compatible: ti,am335x-usb-phy +reg: offset and length of the "USB PHY" register space +ti,ctrl_mod: reference to the "reset module" node +reg-names: phy +The PHY should have a "phy" alias numbered properly in the alias +node. + +USB +~~~ +- compatible: ti,musb-am33xx +- reg: offset and length of "USB Controller Registers", and offset and + length of "USB Core" register space. +- reg-names: control for the ""USB Controller Registers" and "mc" for + "USB Core" register space +- interrupts: USB interrupt number +- interrupt-names: mc +- dr_mode: Should be one of "host", "peripheral" or "otg". +- mentor,multipoint: Should be "1" indicating the musb controller supports + multipoint. This is a MUSB configuration-specific setting. +- mentor,num-eps: Specifies the number of endpoints. This is also a + MUSB configuration-specific setting. Should be set to "16" +- mentor,ram-bits: Specifies the ram address size. Should be set to "12" +- mentor,power: Should be "500". This signifies the controller can supply up to + 500mA when operating in host mode. +- phys: reference to the USB phy +- dmas: specifies the dma channels +- dma-names: specifies the names of the channels. Use "rxN" for receive + and "txN" for transmit endpoints. N specifies the endpoint number. + +The controller should have an "usb" alias numbered properly in the alias +node. + +DMA +~~~ +- compatible: ti,am3359-cppi41 +- reg: offset and length of the following register spaces: USBSS, USB + CPPI DMA Controller, USB CPPI DMA Scheduler, USB Queue Manager +- reg-names: glue, controller, scheduler, queuemgr +- #dma-cells: should be set to 2. The first number represents the + endpoint number (0 … 14 for endpoints 1 … 15 on instance 0 and 15 … 29 + for endpoints 1 … 15 on instance 1). The second number is 0 for RX and + 1 for TX transfers. +- #dma-channels: should be set to 30 representing the 15 endpoints for + each USB instance. Example: +~~~~~~~~ +The following example contains all the nodes as used on am335x-evm: + +aliases { + usb0 = &usb0; + usb1 = &usb1; + phy0 = &usb0_phy; + phy1 = &usb1_phy; +}; -usb@47400000 { - compatible = "ti,musb-am33xx"; - reg = <0x47400000 0x1000 /* usbss */ - 0x47401000 0x800 /* musb instance 0 */ - 0x47401800 0x800>; /* musb instance 1 */ - interrupts = <17 /* usbss */ - 18 /* musb instance 0 */ - 19>; /* musb instance 1 */ - multipoint = <1>; - num-eps = <16>; - ram-bits = <12>; - port0-mode = <3>; - port1-mode = <3>; - power = <250>; +usb: usb@47400000 { + compatible = "ti,am33xx-usb"; + reg = <0x47400000 0x1000>; + ranges; + #address-cells = <1>; + #size-cells = <1>; ti,hwmods = "usb_otg_hs"; + + ctrl_mod: control@44e10000 { + compatible = "ti,am335x-usb-ctrl-module"; + reg = <0x44e10620 0x10 + 0x44e10648 0x4>; + reg-names = "phy_ctrl", "wakeup"; + }; + + usb0_phy: usb-phy@47401300 { + compatible = "ti,am335x-usb-phy"; + reg = <0x47401300 0x100>; + reg-names = "phy"; + ti,ctrl_mod = <&ctrl_mod>; + }; + + usb0: usb@47401000 { + compatible = "ti,musb-am33xx"; + reg = <0x47401400 0x400 + 0x47401000 0x200>; + reg-names = "mc", "control"; + + interrupts = <18>; + interrupt-names = "mc"; + dr_mode = "otg" + mentor,multipoint = <1>; + mentor,num-eps = <16>; + mentor,ram-bits = <12>; + mentor,power = <500>; + phys = <&usb0_phy>; + + dmas = <&cppi41dma 0 0 &cppi41dma 1 0 + &cppi41dma 2 0 &cppi41dma 3 0 + &cppi41dma 4 0 &cppi41dma 5 0 + &cppi41dma 6 0 &cppi41dma 7 0 + &cppi41dma 8 0 &cppi41dma 9 0 + &cppi41dma 10 0 &cppi41dma 11 0 + &cppi41dma 12 0 &cppi41dma 13 0 + &cppi41dma 14 0 &cppi41dma 0 1 + &cppi41dma 1 1 &cppi41dma 2 1 + &cppi41dma 3 1 &cppi41dma 4 1 + &cppi41dma 5 1 &cppi41dma 6 1 + &cppi41dma 7 1 &cppi41dma 8 1 + &cppi41dma 9 1 &cppi41dma 10 1 + &cppi41dma 11 1 &cppi41dma 12 1 + &cppi41dma 13 1 &cppi41dma 14 1>; + dma-names = + "rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7", + "rx8", "rx9", "rx10", "rx11", "rx12", "rx13", + "rx14", "rx15", + "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7", + "tx8", "tx9", "tx10", "tx11", "tx12", "tx13", + "tx14", "tx15"; + }; + + usb1_phy: usb-phy@47401b00 { + compatible = "ti,am335x-usb-phy"; + reg = <0x47401b00 0x100>; + reg-names = "phy"; + ti,ctrl_mod = <&ctrl_mod>; + }; + + usb1: usb@47401800 { + compatible = "ti,musb-am33xx"; + reg = <0x47401c00 0x400 + 0x47401800 0x200>; + reg-names = "mc", "control"; + interrupts = <19>; + interrupt-names = "mc"; + dr_mode = "host" + mentor,multipoint = <1>; + mentor,num-eps = <16>; + mentor,ram-bits = <12>; + mentor,power = <500>; + phys = <&usb1_phy>; + + dmas = <&cppi41dma 15 0 &cppi41dma 16 0 + &cppi41dma 17 0 &cppi41dma 18 0 + &cppi41dma 19 0 &cppi41dma 20 0 + &cppi41dma 21 0 &cppi41dma 22 0 + &cppi41dma 23 0 &cppi41dma 24 0 + &cppi41dma 25 0 &cppi41dma 26 0 + &cppi41dma 27 0 &cppi41dma 28 0 + &cppi41dma 29 0 &cppi41dma 15 1 + &cppi41dma 16 1 &cppi41dma 17 1 + &cppi41dma 18 1 &cppi41dma 19 1 + &cppi41dma 20 1 &cppi41dma 21 1 + &cppi41dma 22 1 &cppi41dma 23 1 + &cppi41dma 24 1 &cppi41dma 25 1 + &cppi41dma 26 1 &cppi41dma 27 1 + &cppi41dma 28 1 &cppi41dma 29 1>; + dma-names = + "rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7", + "rx8", "rx9", "rx10", "rx11", "rx12", "rx13", + "rx14", "rx15", + "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7", + "tx8", "tx9", "tx10", "tx11", "tx12", "tx13", + "tx14", "tx15"; + }; + + cppi41dma: dma-controller@07402000 { + compatible = "ti,am3359-cppi41"; + reg = <0x47400000 0x1000 + 0x47402000 0x1000 + 0x47403000 0x1000 + 0x47404000 0x4000>; + reg-names = "glue", "controller", "scheduler", "queuemgr"; + interrupts = <17>; + interrupt-names = "glue"; + #dma-cells = <2>; + #dma-channels = <30>; + #dma-requests = <256>; + }; }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 7a95c651ceb3..e807635f9e1c 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -3,10 +3,12 @@ synopsys DWC3 CORE DWC3- USB3 CONTROLLER Required properties: - - compatible: must be "synopsys,dwc3" + - compatible: must be "snps,dwc3" - reg : Address and length of the register set for the device - interrupts: Interrupts used by the dwc3 controller. - - usb-phy : array of phandle for the PHY device + - usb-phy : array of phandle for the PHY device. The first element + in the array is expected to be a handle to the USB2/HS PHY and + the second element is expected to be a handle to the USB3/SS PHY Optional properties: - tx-fifo-resize: determines if the FIFO *has* to be reallocated. @@ -14,7 +16,7 @@ Optional properties: This is usually a subnode to DWC3 glue to which it is connected. dwc3@4a030000 { - compatible = "synopsys,dwc3"; + compatible = "snps,dwc3"; reg = <0x4a030000 0xcfff>; interrupts = <0 92 4> usb-phy = <&usb2_phy>, <&usb3,phy>; diff --git a/Documentation/devicetree/bindings/usb/generic.txt b/Documentation/devicetree/bindings/usb/generic.txt new file mode 100644 index 000000000000..477d5bb5e51c --- /dev/null +++ b/Documentation/devicetree/bindings/usb/generic.txt @@ -0,0 +1,24 @@ +Generic USB Properties + +Optional properties: + - maximum-speed: tells USB controllers we want to work up to a certain + speed. Valid arguments are "super-speed", "high-speed", + "full-speed" and "low-speed". In case this isn't passed + via DT, USB controllers should default to their maximum + HW capability. + - dr_mode: tells Dual-Role USB controllers that we want to work on a + particular mode. Valid arguments are "host", + "peripheral" and "otg". In case this attribute isn't + passed via DT, USB DRD controllers should default to + OTG. + +This is an attribute to a USB controller such as: + +dwc3@4a030000 { + compatible = "synopsys,dwc3"; + reg = <0x4a030000 0xcfff>; + interrupts = <0 92 4> + usb-phy = <&usb2_phy>, <&usb3,phy>; + maximum-speed = "super-speed"; + dr_mode = "otg"; +}; diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt index c4c9e9e664aa..ba797d3e6326 100644 --- a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt @@ -3,7 +3,7 @@ Tegra SOC USB PHY The device node for Tegra SOC USB PHY: Required properties : - - compatible : Should be "nvidia,tegra20-usb-phy". + - compatible : Should be "nvidia,tegra<chip>-usb-phy". - reg : Defines the following set of registers, in the order listed: - The PHY's own register set. Always present. @@ -24,17 +24,26 @@ Required properties : Required properties for phy_type == ulpi: - nvidia,phy-reset-gpio : The GPIO used to reset the PHY. -Required PHY timing params for utmi phy: +Required PHY timing params for utmi phy, for all chips: - nvidia,hssync-start-delay : Number of 480 Mhz clock cycles to wait before start of sync launches RxActive - nvidia,elastic-limit : Variable FIFO Depth of elastic input store - nvidia,idle-wait-delay : Number of 480 Mhz clock cycles of idle to wait before declare IDLE. - nvidia,term-range-adj : Range adjusment on terminations - - nvidia,xcvr-setup : HS driver output control + - Either one of the following for HS driver output control: + - nvidia,xcvr-setup : integer, uses the provided value. + - nvidia,xcvr-setup-use-fuses : boolean, indicates that the value is read + from the on-chip fuses + If both are provided, nvidia,xcvr-setup-use-fuses takes precedence. - nvidia,xcvr-lsfslew : LS falling slew rate control. - nvidia,xcvr-lsrslew : LS rising slew rate control. +Required PHY timing params for utmi phy, only on Tegra30 and above: + - nvidia,xcvr-hsslew : HS slew rate control. + - nvidia,hssquelch-level : HS squelch detector level. + - nvidia,hsdiscon-level : HS disconnect detector level. + Optional properties: - nvidia,has-legacy-mode : boolean indicates whether this controller can operate in legacy mode (as APX 2500 / 2600). In legacy mode some @@ -48,5 +57,5 @@ Optional properties: peripheral means it is device controller otg means it can operate as either ("on the go") -Required properties for dr_mode == otg: +VBUS control (required for dr_mode == otg, optional for dr_mode == host): - vbus-supply: regulator for VBUS diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt index 57e71f6817d0..9088ab09e200 100644 --- a/Documentation/devicetree/bindings/usb/omap-usb.txt +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -53,6 +53,11 @@ OMAP DWC3 GLUE It should be set to "1" for HW mode and "2" for SW mode. - ranges: the child address space are mapped 1:1 onto the parent address space +Optional Properties: + - extcon : phandle for the extcon device omap dwc3 uses to detect + connect/disconnect events. + - vbus-supply : phandle to the regulator device tree node if needed. + Sub-nodes: The dwc3 core should be added as subnode to omap dwc3 glue. - dwc3 : diff --git a/Documentation/devicetree/bindings/usb/samsung-hsotg.txt b/Documentation/devicetree/bindings/usb/samsung-hsotg.txt new file mode 100644 index 000000000000..b83d428a265e --- /dev/null +++ b/Documentation/devicetree/bindings/usb/samsung-hsotg.txt @@ -0,0 +1,40 @@ +Samsung High Speed USB OTG controller +----------------------------- + +The Samsung HSOTG IP can be found on Samsung SoCs, from S3C6400 onwards. +It gives functionality of OTG-compliant USB 2.0 host and device with +support for USB 2.0 high-speed (480Mbps) and full-speed (12 Mbps) +operation. + +Currently only device mode is supported. + +Binding details +----- + +Required properties: +- compatible: "samsung,s3c6400-hsotg" should be used for all currently + supported SoC, +- interrupt-parent: phandle for the interrupt controller to which the + interrupt signal of the HSOTG block is routed, +- interrupts: specifier of interrupt signal of interrupt controller, + according to bindings of interrupt controller, +- clocks: contains an array of clock specifiers: + - first entry: OTG clock +- clock-names: contains array of clock names: + - first entry: must be "otg" +- vusb_d-supply: phandle to voltage regulator of digital section, +- vusb_a-supply: phandle to voltage regulator of analog section. + +Example +----- + + hsotg@12480000 { + compatible = "samsung,s3c6400-hsotg"; + reg = <0x12480000 0x20000>; + interrupts = <0 71 0>; + clocks = <&clock 305>; + clock-names = "otg"; + vusb_d-supply = <&vusb_reg>; + vusb_a-supply = <&vusbdac_reg>; + }; + diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt new file mode 100644 index 000000000000..5752df0e17a2 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -0,0 +1,14 @@ +USB xHCI controllers + +Required properties: + - compatible: should be "xhci-platform". + - reg: should contain address and length of the standard XHCI + register set for the device. + - interrupts: one XHCI interrupt should be described here. + +Example: + usb@f0931000 { + compatible = "xhci-platform"; + reg = <0xf0931000 0x8c8>; + interrupts = <0x0 0x4e 0x0>; + }; diff --git a/Documentation/devicetree/bindings/usb/usb3503.txt b/Documentation/devicetree/bindings/usb/usb3503.txt index 8c5be48b43c8..a018da4a7ad7 100644 --- a/Documentation/devicetree/bindings/usb/usb3503.txt +++ b/Documentation/devicetree/bindings/usb/usb3503.txt @@ -1,8 +1,11 @@ SMSC USB3503 High-Speed Hub Controller Required properties: -- compatible: Should be "smsc,usb3503". -- reg: Specifies the i2c slave address, it should be 0x08. +- compatible: Should be "smsc,usb3503" or "smsc,usb3503a". + +Optional properties: +- reg: Specifies the i2c slave address, it is required and should be 0x08 + if I2C is used. - connect-gpios: Should specify GPIO for connect. - disabled-ports: Should specify the ports unused. '1' or '2' or '3' are availe for this property to describe the port diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 366ce9b87240..ec4d713674fa 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -11,6 +11,7 @@ amcc Applied Micro Circuits Corporation (APM, formally AMCC) apm Applied Micro Circuits Corporation (APM) arm ARM Ltd. atmel Atmel Corporation +avago Avago Technologies bosch Bosch Sensortec GmbH brcm Broadcom Corporation cavium Cavium, Inc. diff --git a/Documentation/driver-model/devres.txt b/Documentation/driver-model/devres.txt index b4671459857f..fb57d85e7316 100644 --- a/Documentation/driver-model/devres.txt +++ b/Documentation/driver-model/devres.txt @@ -237,6 +237,12 @@ MEM devm_kzalloc() devm_kfree() +IIO + devm_iio_device_alloc() + devm_iio_device_free() + devm_iio_trigger_alloc() + devm_iio_trigger_free() + IO region devm_request_region() devm_request_mem_region() diff --git a/Documentation/hwmon/ads1015 b/Documentation/hwmon/ads1015 index f6fe9c203733..063b80d857b1 100644 --- a/Documentation/hwmon/ads1015 +++ b/Documentation/hwmon/ads1015 @@ -6,6 +6,10 @@ Supported chips: Prefix: 'ads1015' Datasheet: Publicly available at the Texas Instruments website : http://focus.ti.com/lit/ds/symlink/ads1015.pdf + * Texas Instruments ADS1115 + Prefix: 'ads1115' + Datasheet: Publicly available at the Texas Instruments website : + http://focus.ti.com/lit/ds/symlink/ads1115.pdf Authors: Dirk Eibach, Guntermann & Drunck GmbH <eibach@gdsys.de> @@ -13,9 +17,9 @@ Authors: Description ----------- -This driver implements support for the Texas Instruments ADS1015. +This driver implements support for the Texas Instruments ADS1015/ADS1115. -This device is a 12-bit A-D converter with 4 inputs. +This device is a 12/16-bit A-D converter with 4 inputs. The inputs can be used single ended or in certain differential combinations. diff --git a/Documentation/hwmon/htu21 b/Documentation/hwmon/htu21 new file mode 100644 index 000000000000..f39a215fb6ae --- /dev/null +++ b/Documentation/hwmon/htu21 @@ -0,0 +1,46 @@ +Kernel driver htu21 +=================== + +Supported chips: + * Measurement Specialties HTU21D + Prefix: 'htu21' + Addresses scanned: none + Datasheet: Publicly available at the Measurement Specialties website + http://www.meas-spec.com/downloads/HTU21D.pdf + + +Author: + William Markezana <william.markezana@meas-spec.com> + +Description +----------- + +The HTU21D is a humidity and temperature sensor in a DFN package of +only 3 x 3 mm footprint and 0.9 mm height. + +The devices communicate with the I2C protocol. All sensors are set to the +same I2C address 0x40, so an entry with I2C_BOARD_INFO("htu21", 0x40) can +be used in the board setup code. + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices +for details. + +sysfs-Interface +--------------- + +temp1_input - temperature input +humidity1_input - humidity input + +Notes +----- + +The driver uses the default resolution settings of 12 bit for humidity and 14 +bit for temperature, which results in typical measurement times of 11 ms for +humidity and 44 ms for temperature. To keep self heating below 0.1 degree +Celsius, the device should not be active for more than 10% of the time. For +this reason, the driver performs no more than two measurements per second and +reports cached information if polled more frequently. + +Different resolutions, the on-chip heater, using the CRC checksum and reading +the serial number are not supported yet. diff --git a/Documentation/hwmon/k10temp b/Documentation/hwmon/k10temp index 90956b618025..4dfdc8f83633 100644 --- a/Documentation/hwmon/k10temp +++ b/Documentation/hwmon/k10temp @@ -12,6 +12,7 @@ Supported chips: * AMD Family 12h processors: "Llano" (E2/A4/A6/A8-Series) * AMD Family 14h processors: "Brazos" (C/E/G/Z-Series) * AMD Family 15h processors: "Bulldozer" (FX-Series), "Trinity" +* AMD Family 16h processors: "Kabini" Prefix: 'k10temp' Addresses scanned: PCI space diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 15356aca938c..31a9e5174e63 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -2953,7 +2953,7 @@ bytes respectively. Such letter suffixes can also be entirely omitted. improve throughput, but will also increase the amount of memory reserved for use by the client. - swapaccount[=0|1] + swapaccount=[0|1] [KNL] Enable accounting of swap in memory resource controller if no parameter or 1 is given or disable it if 0 is given (See Documentation/cgroups/memory.txt) @@ -3322,6 +3322,10 @@ bytes respectively. Such letter suffixes can also be entirely omitted. them quite hard to use for exploits but might break your system. + vt.color= [VT] Default text color. + Format: 0xYX, X = foreground, Y = background. + Default: 0x07 = light gray on black. + vt.cur_default= [VT] Default cursor shape. Format: 0xCCBBAA, where AA, BB, and CC are the same as the parameters of the <Esc>[?A;B;Cc escape sequence; @@ -3361,6 +3365,12 @@ bytes respectively. Such letter suffixes can also be entirely omitted. overridden by individual drivers. 0 will hide cursors, 1 will display them. + vt.italic= [VT] Default color for italic text; 0-15. + Default: 2 = green. + + vt.underline= [VT] Default color for underlined text; 0-15. + Default: 3 = cyan. + watchdog timers [HW,WDT] For information on watchdog timers, see Documentation/watchdog/watchdog-parameters.txt or other driver-specific files in the diff --git a/Documentation/ko_KR/HOWTO b/Documentation/ko_KR/HOWTO index 2f48f205fedc..680e64635958 100644 --- a/Documentation/ko_KR/HOWTO +++ b/Documentation/ko_KR/HOWTO @@ -182,8 +182,8 @@ Documentation/DocBook/ 디렉토리 내에서 만들어지며 PDF, Postscript, H 프로젝트를 봐야 한다. http://kernelnewbies.org 그곳은 거의 모든 종류의 기본적인 커널 개발 질문들(질문하기 전에 먼저 -아카이브를 찾아봐라. 과거에 이미 답변되었을 수도 있다)을 할수있는 도움이 -될만한 메일링 리스트가 있다. 또한 실시간으로 질문 할수 있는 IRC 채널도 +아카이브를 찾아봐라. 과거에 이미 답변되었을 수도 있다)을 할 수 있는 도움이 +될만한 메일링 리스트가 있다. 또한 실시간으로 질문 할 수 있는 IRC 채널도 가지고 있으며 리눅스 커널 개발을 배우는 데 유용한 문서들을 보유하고 있다. 웹사이트는 코드구성, 서브시스템들, 그리고 현재 프로젝트들 @@ -245,7 +245,7 @@ Documentation/DocBook/ 디렉토리 내에서 만들어지며 PDF, Postscript, H 것을 기억해라. 왜냐하면 변경이 자체내에서만 발생하고 추가된 코드가 드라이버 외부의 다른 부분에는 영향을 주지 않으므로 그런 변경은 회귀(역자주: 이전에는 존재하지 않았지만 새로운 기능추가나 변경으로 인해 - 생겨난 버그)를 일으킬 만한 위험을 가지고 있지 않기 때문이다. -rc1이 + 생겨난 버그)를 일으킬 만한 위험을 가지고 있지 않기 때문이다. -rc1이 배포된 이후에 git를 사용하여 패치들을 Linus에게 보낼수 있지만 패치들은 공식적인 메일링 리스트로 보내서 검토를 받을 필요가 있다. - 새로운 -rc는 Linus가 현재 git tree가 테스트 하기에 충분히 안정된 상태에 @@ -455,7 +455,7 @@ bugme-janitor 메일링 리스트(bugzilla에 모든 변화들이 여기서 메 - 의견 - 변경을 위한 요구 - 당위성을 위한 요구 - - 고요 + - 침묵 기억하라. 이것들은 여러분의 패치가 커널로 들어가기 위한 과정이다. 여러분의 패치들은 비판과 다른 의견을 받을 수 있고 그것들을 기술적인 레벨로 평가하고 @@ -472,7 +472,7 @@ bugme-janitor 메일링 리스트(bugzilla에 모든 변화들이 여기서 메 가능한한 가장 좋은 기술적인 해답을 찾고 있는 커뮤니티에서는 항상 어떤 패치가 얼마나 좋은지에 관하여 다른 의견들이 있을 수 있다. 여러분은 협조적이어야 하고 기꺼이 여러분의 생각을 커널 내에 맞추어야 한다. 아니면 -적어도 여러분의 것이 가치있다는 것을 중명하여야 한다. 잘못된 것도 여러분이 +적어도 여러분의 것이 가치있다는 것을 증명하여야 한다. 잘못된 것도 여러분이 올바른 방향의 해결책으로 이끌어갈 의지가 있다면 받아들여질 것이라는 점을 기억하라. @@ -488,21 +488,21 @@ bugme-janitor 메일링 리스트(bugzilla에 모든 변화들이 여기서 메 커널 커뮤니티는 가장 전통적인 회사의 개발 환경과는 다르다. 여기에 여러분들의 문제를 피하기 위한 목록이 있다. 여러분들이 제안한 변경들에 관하여 말할 때 좋은 것들 : - - "이것은 여러 문제들을 해겹합니다." - - "이것은 2000 라인의 코드를 제거합니다." + - "이것은 여러 문제들을 해결합니다." + - "이것은 2000 라인의 코드를 줄입니다." - "이것은 내가 말하려는 것에 관해 설명하는 패치입니다." - - "나는 5개의 다른 아키텍쳐에서 그것을 테스트했슴으로..." - - "여기에 일련의 작은 패치들이 있슴음로..." - - "이것은 일반적인 머신에서 성능을 향상시킴으로..." + - "나는 5개의 다른 아키텍쳐에서 그것을 테스트 했으므로..." + - "여기에 일련의 작은 패치들이 있으므로..." + - "이것은 일반적인 머신에서 성능을 향상함으로..." 여러분들이 말할 때 피해야 할 좋지 않은 것들 : - - "우리를 그것을 AIT/ptx/Solaris에서 이러한 방법으로 했다. 그러므로 그것은 좋은 것임에 틀립없다..." + - "우리는 그것을 AIX/ptx/Solaris에서 이러한 방법으로 했다. 그러므로 그것은 좋은 것임에 틀림없다..." - "나는 20년동안 이것을 해왔다. 그러므로..." - "이것은 돈을 벌기위해 나의 회사가 필요로 하는 것이다." - "이것은 우리의 엔터프라이즈 상품 라인을 위한 것이다." - "여기에 나의 생각을 말하고 있는 1000 페이지 설계 문서가 있다." - "나는 6달동안 이것을 했으니..." - - "여기에 5000라인 짜리 패치가 있으니..." + - "여기에 5000 라인 짜리 패치가 있으니..." - "나는 현재 뒤죽박죽인 것을 재작성했다. 그리고 여기에..." - "나는 마감시한을 가지고 있으므로 이 패치는 지금 적용될 필요가 있다." @@ -574,6 +574,7 @@ Pat이라는 이름을 가진 여자가 있을 수도 있는 것이다. 리눅 또한 완성되지 않았고 "나중에 수정될 것이다." 와 같은 것들을 포함하는 패치들은 받아들여지지 않을 것이라는 점을 유념하라. + 변경을 정당화해라 ----------------- diff --git a/Documentation/ko_KR/stable_api_nonsense.txt b/Documentation/ko_KR/stable_api_nonsense.txt index 8f2b0e1d98c4..51f85ade4190 100644 --- a/Documentation/ko_KR/stable_api_nonsense.txt +++ b/Documentation/ko_KR/stable_api_nonsense.txt @@ -106,12 +106,12 @@ Greg Kroah-Hartman <greg@kroah.com> --------------------------------- 리눅스 커널 드라이버를 계속해서 메인 커널 트리에 반영하지 않고 -유지보수하려고 하는 사름들과 이 문제를 논의하게 되면 훨씬 더 +유지보수하려고 하는 사람들과 이 문제를 논의하게 되면 훨씬 더 "논란의 여지가 많은" 주제가 될 것이다. 리눅스 커널 개발은 끊임없이 빠른 속도로 이루어지고 있으며 결코 느슨해진 적이 없다. 커널 개발자들이 현재 인터페이스들에서 버그를 -발견하거나 무엇인가 할수 있는 더 좋은 방법을 찾게 되었다고 하자. +발견하거나 무엇인가 할 수 있는 더 좋은 방법을 찾게 되었다고 하자. 그들이 발견한 것을 실행한다면 아마도 더 잘 동작하도록 현재 인터페이스들을 수정하게 될 것이다. 그들이 그런 일을 하게되면 함수 이름들은 변하게 되고, 구조체들은 늘어나거나 줄어들게 되고, 함수 파라미터들은 재작업될 것이다. @@ -174,7 +174,7 @@ GPL을 따르는 배포 드라이버에 관해 얘기하고 있다는 것을 상 동작하는 것을 보장한다. 메인 커널 트리에 여러분의 드라이버를 반영하면 얻게 되는 장점들은 다음과 같다. - - 관리의 드는 비용(원래 개발자의)은 줄어줄면서 드라이버의 질은 향상될 것이다. + - 관리에 드는 비용(원래 개발자의)은 줄어줄면서 드라이버의 질은 향상될 것이다. - 다른 개발자들이 여러분의 드라이버에 기능들을 추가 할 것이다. - 다른 사람들은 여러분의 드라이버에 버그를 발견하고 수정할 것이다. - 다른 사람들은 여러분의 드라이버의 개선점을 찾을 줄 것이다. diff --git a/Documentation/spi/spi-summary b/Documentation/spi/spi-summary index 2331eb214146..f21edb983413 100644 --- a/Documentation/spi/spi-summary +++ b/Documentation/spi/spi-summary @@ -215,7 +215,7 @@ So for example arch/.../mach-*/board-*.c files might have code like: /* if your mach-* infrastructure doesn't support kernels that can * run on multiple boards, pdata wouldn't benefit from "__init". */ - static struct mysoc_spi_data __initdata pdata = { ... }; + static struct mysoc_spi_data pdata __initdata = { ... }; static __init board_init(void) { diff --git a/Documentation/usb/URB.txt b/Documentation/usb/URB.txt index 00d2c644068e..50da0d455444 100644 --- a/Documentation/usb/URB.txt +++ b/Documentation/usb/URB.txt @@ -195,13 +195,12 @@ by the completion handler. The handler is of the following type: - typedef void (*usb_complete_t)(struct urb *, struct pt_regs *) + typedef void (*usb_complete_t)(struct urb *) -I.e., it gets the URB that caused the completion call, plus the -register values at the time of the corresponding interrupt (if any). -In the completion handler, you should have a look at urb->status to -detect any USB errors. Since the context parameter is included in the URB, -you can pass information to the completion handler. +I.e., it gets the URB that caused the completion call. In the completion +handler, you should have a look at urb->status to detect any USB errors. +Since the context parameter is included in the URB, you can pass +information to the completion handler. Note that even when an error (or unlink) is reported, data may have been transferred. That's because USB transfers are packetized; it might take @@ -210,12 +209,12 @@ have transferred successfully before the completion was called. NOTE: ***** WARNING ***** -NEVER SLEEP IN A COMPLETION HANDLER. These are normally called -during hardware interrupt processing. If you can, defer substantial -work to a tasklet (bottom half) to keep system latencies low. You'll -probably need to use spinlocks to protect data structures you manipulate -in completion handlers. +NEVER SLEEP IN A COMPLETION HANDLER. These are often called in atomic +context. +In the current kernel, completion handlers run with local interrupts +disabled, but in the future this will be changed, so don't assume that +local IRQs are always disabled inside completion handlers. 1.8. How to do isochronous (ISO) transfers? diff --git a/Documentation/usb/proc_usb_info.txt b/Documentation/usb/proc_usb_info.txt index c9c3f0f5ad7b..98be91982677 100644 --- a/Documentation/usb/proc_usb_info.txt +++ b/Documentation/usb/proc_usb_info.txt @@ -54,9 +54,12 @@ it and 002/048 sometime later. These files can be read as binary data. The binary data consists of first the device descriptor, then the descriptors for each -configuration of the device. Multi-byte fields in the device and -configuration descriptors, but not other descriptors, are converted -to host endianness by the kernel. This information is also shown +configuration of the device. Multi-byte fields in the device descriptor +are converted to host endianness by the kernel. The configuration +descriptors are in bus endian format! The configuration descriptor +are wTotalLength bytes apart. If a device returns less configuration +descriptor data than indicated by wTotalLength there will be a hole in +the file for the missing bytes. This information is also shown in text form by the /proc/bus/usb/devices file, described later. These files may also be used to write user-level drivers for the USB |