diff options
Diffstat (limited to 'arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts')
| -rw-r--r-- | arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts | 45 |
1 files changed, 12 insertions, 33 deletions
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts index 37343148643d..ec721d323ac5 100644 --- a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts +++ b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts @@ -4,6 +4,7 @@ #include "bcm2836-rpi.dtsi" #include "bcm283x-rpi-lan7515.dtsi" #include "bcm283x-rpi-usb-host.dtsi" +#include "bcm283x-rpi-wifi-bt.dtsi" / { compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837"; @@ -20,22 +21,21 @@ }; leds { - act { + led-act { gpios = <&gpio 29 GPIO_ACTIVE_HIGH>; }; - pwr { + led-pwr { label = "PWR"; gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; default-state = "keep"; linux,default-trigger = "default-on"; }; }; +}; - wifi_pwrseq: wifi-pwrseq { - compatible = "mmc-pwrseq-simple"; - reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>; - }; +&bt { + shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; }; &firmware { @@ -45,7 +45,7 @@ #gpio-cells = <2>; gpio-line-names = "BT_ON", "WL_ON", - "STATUS_LED_R", + "PWR_LED_R", "LAN_RUN", "", "CAM_GPIO0", @@ -61,7 +61,6 @@ * the official GPU firmware DT blob. * * Legend: - * "NC" = not connected (no rail from the SoC) * "FOO" = GPIO line named "FOO" on the schematic * "FOO_N" = GPIO line named "FOO" on schematic, active low */ @@ -110,7 +109,7 @@ "SD1_DATA3", "PWM0_OUT", "PWM1_OUT", - "ETHCLK", + "ETH_CLK", "WIFI_CLK", "SDA0", "SCL0", @@ -137,23 +136,6 @@ status = "okay"; }; -/* SDHCI is used to control the SDIO for wireless */ -&sdhci { - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&emmc_gpio34>; - status = "okay"; - bus-width = <4>; - non-removable; - mmc-pwrseq = <&wifi_pwrseq>; - - brcmf: wifi@1 { - reg = <1>; - compatible = "brcm,bcm4329-fmac"; - }; -}; - /* SDHOST is used to drive the SD card */ &sdhost { pinctrl-names = "default"; @@ -166,13 +148,6 @@ &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>; - status = "okay"; - - bluetooth { - compatible = "brcm,bcm43438-bt"; - max-speed = <2000000>; - shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; - }; }; /* uart1 is mapped to the pin header */ @@ -181,3 +156,7 @@ pinctrl-0 = <&uart1_gpio14>; status = "okay"; }; + +&wifi_pwrseq { + reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>; +}; |