diff options
Diffstat (limited to '')
| -rw-r--r-- | arch/arm/boot/dts/intel-ixp42x-arcom-vulcan.dts | 169 |
1 files changed, 169 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/intel-ixp42x-arcom-vulcan.dts b/arch/arm/boot/dts/intel-ixp42x-arcom-vulcan.dts new file mode 100644 index 000000000000..92b987bc3f99 --- /dev/null +++ b/arch/arm/boot/dts/intel-ixp42x-arcom-vulcan.dts @@ -0,0 +1,169 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for the Arcom/Eurotech Vulcan board. + * This board is a single board computer in the PC/104 form factor based on + * IXP425, and was released around 2005. It previously had the name "Mercury". + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Arcom/Eurotech Vulcan"; + compatible = "arcom,vulcan", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x4000000>; + }; + + chosen { + /* CHECKME: using a harddrive at /dev/sda1 as rootfs by default */ + bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootfstype=ext4 rootwait"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + onewire { + compatible = "w1-gpio"; + gpios = <&gpio0 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* + * 32 MB of Flash in 0x20000 byte blocks + * mapped in at CS0 and CS1. + * + * The documentation mentions the existence + * of a 16MB version, which we conveniently + * ignore. Shout if you own one! + */ + reg = <0 0x00000000 0x2000000>; + + /* Expansion bus settings */ + intel,ixp4xx-eb-t3 = <3>; + intel,ixp4xx-eb-byte-access-on-halfword = <1>; + intel,ixp4xx-eb-write-enable = <1>; + + partitions { + compatible = "redboot-fis"; + fis-index-block = <0x1ff>; + }; + }; + sram@2,0 { + /* 256 KB SDRAM memory at CS2 */ + compatible = "shared-dma-pool"; + device_type = "memory"; + reg = <2 0x00000000 0x40000>; + no-map; + /* Expansion bus settings */ + intel,ixp4xx-eb-t3 = <1>; + intel,ixp4xx-eb-t4 = <2>; + intel,ixp4xx-eb-ahb-split-transfers = <1>; + intel,ixp4xx-eb-write-enable = <1>; + intel,ixp4xx-eb-byte-access = <1>; + }; + serial@3,0 { + /* + * 8250-compatible Exar XR16L2551 2 x UART + * + * CHECKME: if special tweaks are needed, then fix the + * operating system to handle it. + */ + compatible = "exar,xr16l2551", "ns8250"; + reg = <3 0x00000000 0x10>; + interrupt-parent = <&gpio0>; + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; + clock-frequency = <1843200>; + /* Expansion bus settings */ + intel,ixp4xx-eb-t3 = <3>; + intel,ixp4xx-eb-cycle-type = <1>; /* Motorola cycles */ + intel,ixp4xx-eb-write-enable = <1>; + intel,ixp4xx-eb-byte-access = <1>; + }; + gpio1: gpio@4,0 { + /* + * MMIO GPIO in one byte + */ + compatible = "arcom,vulcan-gpio"; + reg = <4 0x00000000 0x1>; + /* Expansion bus settings */ + intel,ixp4xx-eb-write-enable = <1>; + intel,ixp4xx-eb-byte-access = <1>; + }; + watchdog@5,0 { + compatible = "maxim,max6369"; + reg = <5 0x00000000 0x1>; + /* Expansion bus settings */ + intel,ixp4xx-eb-write-enable = <1>; + intel,ixp4xx-eb-byte-access = <1>; + }; + }; + + pci@c0000000 { + status = "ok"; + + /* + * Taken from Vulcan PCI boardfile. + * + * We have 2 slots (IDSEL) 1 and 2 with one dedicated interrupt + * per slot. This interrupt is shared (OR:ed) by all four pins. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 2 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 2 */ + <0x0800 0 0 2 &gpio0 2 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 2 */ + <0x0800 0 0 3 &gpio0 2 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 2 */ + <0x0800 0 0 4 &gpio0 2 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 2 */ + /* IDSEL 2 */ + <0x1000 0 0 1 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 3 */ + <0x1000 0 0 2 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 3 */ + <0x1000 0 0 3 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 3 */ + <0x1000 0 0 4 &gpio0 3 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 3 */ + }; + + /* EthB */ + ethernet@c8009000 { + status = "ok"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + }; + + /* EthC */ + ethernet@c800a000 { + status = "ok"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + }; + }; +}; |