diff options
Diffstat (limited to 'arch/arm/boot/dts/intel-ixp42x-freecom-fsg-3.dts')
| -rw-r--r-- | arch/arm/boot/dts/intel-ixp42x-freecom-fsg-3.dts | 219 |
1 files changed, 219 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/intel-ixp42x-freecom-fsg-3.dts b/arch/arm/boot/dts/intel-ixp42x-freecom-fsg-3.dts new file mode 100644 index 000000000000..b740403b05a9 --- /dev/null +++ b/arch/arm/boot/dts/intel-ixp42x-freecom-fsg-3.dts @@ -0,0 +1,219 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for the Freecom FSG-3 router. + * This machine is based on IXP425. + * This device tree is inspired by the board file by Rod Whitby. + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Freecom FSG-3"; + compatible = "freecom,fsg-3", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 64 MB memory */ + device_type = "memory"; + reg = <0x00000000 0x4000000>; + }; + + chosen { + /* Boot from the first partition on the hard drive */ + bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootfstype=ext4 rootwait"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + gpio_keys { + compatible = "gpio-keys"; + + button-sync { + wakeup-source; + /* Closest approximation of what the key should do */ + linux,code = <KEY_CONNECT>; + label = "sync"; + gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; + }; + button-reset { + wakeup-source; + linux,code = <KEY_ESC>; + label = "reset"; + gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; + }; + button-usb { + wakeup-source; + /* Unplug USB, closest approximation of what the key should do */ + linux,code = <KEY_EJECTCD>; + label = "usb"; + gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; + }; + }; + + i2c { + compatible = "i2c-gpio"; + sda-gpios = <&gpio0 12 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio0 13 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + #address-cells = <1>; + #size-cells = <0>; + + hwmon@28 { + /* + * Temperature sensor and fan control chip. + * + * TODO: create a proper device tree binding for + * the sensor and temperature zone and create a + * zone with fan control. + */ + compatible = "winbond,w83781d"; + reg = <0x28>; + }; + rtc@6f { + compatible = "isil,isl1208"; + reg = <0x6f>; + }; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* Enable writes on the expansion bus */ + intel,ixp4xx-eb-write-enable = <1>; + /* 4 MB of Flash mapped in at CS0 */ + reg = <0 0x00000000 0x400000>; + + partitions { + compatible = "redboot-fis"; + /* Eraseblock at 0x3e0000 */ + fis-index-block = <0x1f>; + }; + }; + + /* Small syscon with some LEDs at CS2 */ + syscon@2,0 { + compatible = "freecom,fsg-cs2-system-controller", "syscon"; + reg = <2 0x0 0x200>; + reg-io-width = <2>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <2 0x0 0x0 0x200>; + + led@0,0 { + compatible = "register-bit-led"; + reg = <0x00 0x02>; + mask = <0x01>; + label = "fsg:blue:wlan"; + linux,default-trigger = "wlan"; + default-state = "on"; + }; + led@0,1 { + compatible = "register-bit-led"; + reg = <0x00 0x02>; + mask = <0x02>; + label = "fsg:blue:wan"; + linux,default-trigger = ""; + default-state = "on"; + }; + led@0,2 { + compatible = "register-bit-led"; + reg = <0x00 0x02>; + mask = <0x04>; + label = "fsg:blue:sata"; + linux,default-trigger = ""; + default-state = "on"; + }; + led@0,3 { + compatible = "register-bit-led"; + reg = <0x00 0x02>; + mask = <0x04>; + label = "fsg:blue:usb"; + linux,default-trigger = ""; + default-state = "on"; + }; + led@0,4 { + compatible = "register-bit-led"; + reg = <0x00 0x02>; + mask = <0x08>; + label = "fsg:blue:sync"; + linux,default-trigger = ""; + default-state = "on"; + }; + led@0,5 { + compatible = "register-bit-led"; + reg = <0x00 0x02>; + mask = <0x10>; + label = "fsg:blue:ring"; + linux,default-trigger = ""; + default-state = "on"; + }; + }; + }; + + pci@c0000000 { + status = "ok"; + + /* + * Written based on the FSG-3 PCI boardfile. + * We have slots 12, 13 & 14 (IDSEL) with one IRQ each. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 12 */ + <0x6000 0 0 1 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 12 is irq 5 */ + <0x6000 0 0 2 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 12 is irq 5 */ + <0x6000 0 0 3 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 12 is irq 5 */ + <0x6000 0 0 4 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 12 is irq 5 */ + /* IDSEL 13 */ + <0x6800 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 13 is irq 7 */ + <0x6800 0 0 2 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 13 is irq 7 */ + <0x6800 0 0 3 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 13 is irq 7 */ + <0x6800 0 0 4 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 13 is irq 7 */ + /* IDSEL 14 */ + <0x7000 0 0 1 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 6 */ + <0x7000 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 14 is irq 6 */ + <0x7000 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 14 is irq 6 */ + <0x7000 0 0 4 &gpio0 6 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 14 is irq 6 */ + }; + + /* EthB */ + ethernet@c8009000 { + status = "ok"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy4: ethernet-phy@4 { + reg = <4>; + }; + + phy5: ethernet-phy@5 { + reg = <5>; + }; + }; + }; + + /* EthC */ + ethernet@c800a000 { + status = "ok"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy4>; + }; + }; +}; |