diff options
Diffstat (limited to 'arch/arm/boot/dts/motorola-mapphone-common.dtsi')
| -rw-r--r-- | arch/arm/boot/dts/motorola-mapphone-common.dtsi | 223 |
1 files changed, 73 insertions, 150 deletions
diff --git a/arch/arm/boot/dts/motorola-mapphone-common.dtsi b/arch/arm/boot/dts/motorola-mapphone-common.dtsi index b6e82b165f5c..c7a1f3ffc48c 100644 --- a/arch/arm/boot/dts/motorola-mapphone-common.dtsi +++ b/arch/arm/boot/dts/motorola-mapphone-common.dtsi @@ -113,40 +113,17 @@ enable-active-high; }; - gpio_keys { - compatible = "gpio-keys"; - - volume_down { - label = "Volume Down"; - gpios = <&gpio5 26 GPIO_ACTIVE_LOW>; /* gpio154 */ - linux,code = <KEY_VOLUMEDOWN>; - linux,can-disable; - /* Value above 7.95ms for no GPIO hardware debounce */ - debounce-interval = <10>; - }; - - slider { - label = "Keypad Slide"; - gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; /* gpio122 */ - linux,input-type = <EV_SW>; - linux,code = <SW_KEYPAD_SLIDE>; - linux,can-disable; - /* Value above 7.95ms for no GPIO hardware debounce */ - debounce-interval = <10>; - }; - }; - soundcard { compatible = "audio-graph-card"; - label = "Droid 4 Audio"; + label = "Mapphone Audio"; - simple-graph-card,widgets = + widgets = "Speaker", "Earpiece", "Speaker", "Loudspeaker", "Headphone", "Headphone Jack", "Microphone", "Internal Mic"; - simple-graph-card,routing = + routing = "Earpiece", "EP", "Loudspeaker", "SPKR", "Headphone Jack", "HSL", @@ -192,6 +169,29 @@ }; }; +&cpu_thermal { + polling-delay = <10000>; /* milliseconds */ +}; + +&cpu_alert0 { + temperature = <80000>; /* millicelsius */ +}; + +&cpu0 { + /* + * Note that the 1.2GiHz mode is enabled for all SoC variants for + * the Motorola Android Linux v3.0.8 based kernel. + */ + operating-points = < + /* kHz uV */ + 300000 1025000 + 600000 1200000 + 800000 1313000 + 1008000 1375000 + 1200000 1375000 + >; +}; + &dss { status = "okay"; }; @@ -207,8 +207,9 @@ }; }; - lcd0: display { - compatible = "panel-dsi-cm"; + lcd0: panel@0 { + compatible = "motorola,droid4-panel", "panel-dsi-cm"; + reg = <0>; label = "lcd0"; vddi-supply = <&lcd_regulator>; reset-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* gpio101 */ @@ -217,6 +218,7 @@ width-mm = <50>; height-mm = <89>; + rotation = <90>; panel-timing { clock-frequency = <0>; /* Calculated by dsi */ @@ -280,80 +282,6 @@ }; }; -&keypad { - keypad,num-rows = <8>; - keypad,num-columns = <8>; - linux,keymap = < - - /* Row 1 */ - MATRIX_KEY(0, 2, KEY_1) - MATRIX_KEY(0, 6, KEY_2) - MATRIX_KEY(2, 3, KEY_3) - MATRIX_KEY(0, 7, KEY_4) - MATRIX_KEY(0, 4, KEY_5) - MATRIX_KEY(5, 5, KEY_6) - MATRIX_KEY(0, 1, KEY_7) - MATRIX_KEY(0, 5, KEY_8) - MATRIX_KEY(0, 0, KEY_9) - MATRIX_KEY(1, 6, KEY_0) - - /* Row 2 */ - MATRIX_KEY(3, 4, KEY_APOSTROPHE) - MATRIX_KEY(7, 6, KEY_Q) - MATRIX_KEY(7, 7, KEY_W) - MATRIX_KEY(7, 2, KEY_E) - MATRIX_KEY(1, 0, KEY_R) - MATRIX_KEY(4, 4, KEY_T) - MATRIX_KEY(1, 2, KEY_Y) - MATRIX_KEY(6, 7, KEY_U) - MATRIX_KEY(2, 2, KEY_I) - MATRIX_KEY(5, 6, KEY_O) - MATRIX_KEY(3, 7, KEY_P) - MATRIX_KEY(6, 5, KEY_BACKSPACE) - - /* Row 3 */ - MATRIX_KEY(5, 4, KEY_TAB) - MATRIX_KEY(5, 7, KEY_A) - MATRIX_KEY(2, 7, KEY_S) - MATRIX_KEY(7, 0, KEY_D) - MATRIX_KEY(2, 6, KEY_F) - MATRIX_KEY(6, 2, KEY_G) - MATRIX_KEY(6, 6, KEY_H) - MATRIX_KEY(1, 4, KEY_J) - MATRIX_KEY(3, 1, KEY_K) - MATRIX_KEY(2, 1, KEY_L) - MATRIX_KEY(4, 6, KEY_ENTER) - - /* Row 4 */ - MATRIX_KEY(3, 6, KEY_LEFTSHIFT) /* KEY_CAPSLOCK */ - MATRIX_KEY(6, 1, KEY_Z) - MATRIX_KEY(7, 4, KEY_X) - MATRIX_KEY(5, 1, KEY_C) - MATRIX_KEY(1, 7, KEY_V) - MATRIX_KEY(2, 4, KEY_B) - MATRIX_KEY(4, 1, KEY_N) - MATRIX_KEY(1, 1, KEY_M) - MATRIX_KEY(3, 5, KEY_COMMA) - MATRIX_KEY(5, 2, KEY_DOT) - MATRIX_KEY(6, 3, KEY_UP) - MATRIX_KEY(7, 3, KEY_OK) - - /* Row 5 */ - MATRIX_KEY(2, 5, KEY_LEFTCTRL) /* KEY_LEFTSHIFT */ - MATRIX_KEY(4, 5, KEY_LEFTALT) /* SYM */ - MATRIX_KEY(6, 0, KEY_MINUS) - MATRIX_KEY(4, 7, KEY_EQUAL) - MATRIX_KEY(1, 5, KEY_SPACE) - MATRIX_KEY(3, 2, KEY_SLASH) - MATRIX_KEY(4, 3, KEY_LEFT) - MATRIX_KEY(5, 3, KEY_DOWN) - MATRIX_KEY(3, 3, KEY_RIGHT) - - /* Side buttons, KEY_VOLUMEDOWN and KEY_PWER are on CPCAP? */ - MATRIX_KEY(5, 0, KEY_VOLUMEUP) - >; -}; - &mmc1 { vmmc-supply = <&vwlan2>; bus-width = <4>; @@ -367,6 +295,8 @@ }; &mmc3 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins>; vmmc-supply = <&wl12xx_vmmc>; /* uart2_tx.sdmmc3_dat1 pad as wakeirq */ interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH @@ -380,7 +310,7 @@ #address-cells = <1>; #size-cells = <0>; wlcore: wlcore@2 { - compatible = "ti,wl1285", "ti,wl1283"; + compatible = "ti,wl1285"; reg = <2>; /* gpio_100 with gpmc_wait2 pad as wakeirq */ interrupts-extended = <&gpio4 4 IRQ_TYPE_LEVEL_HIGH>, @@ -391,34 +321,6 @@ }; }; -&i2c1 { - led-controller@38 { - compatible = "ti,lm3532"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x38>; - - enable-gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>; - - ramp-up-us = <1024>; - ramp-down-us = <8193>; - - backlight_led: led@0 { - reg = <0>; - led-sources = <2>; - ti,led-mode = <0>; - label = ":backlight"; - }; - - led@1 { - reg = <1>; - led-sources = <1>; - ti,led-mode = <0>; - label = ":kbd_backlight"; - }; - }; -}; - &i2c2 { touchscreen@4a { compatible = "atmel,maxtouch"; @@ -426,10 +328,10 @@ pinctrl-names = "default"; pinctrl-0 = <&touchscreen_pins>; - reset-gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>; /* gpio173 */ + reset-gpios = <&gpio6 13 GPIO_ACTIVE_LOW>; /* gpio173 */ /* gpio_183 with sys_nirq2 pad as wakeup */ - interrupts-extended = <&gpio6 23 IRQ_TYPE_EDGE_FALLING>, + interrupts-extended = <&gpio6 23 IRQ_TYPE_LEVEL_LOW>, <&omap4_pmx_core 0x160>; interrupt-names = "irq", "wakeup"; wakeup-source; @@ -472,6 +374,37 @@ >; }; + /* + * Android uses PIN_OFF_INPUT_PULLDOWN | PIN_INPUT_PULLUP | MUX_MODE3 + * for gpio_100, but the internal pull makes wlan flakey on some + * devices. Off mode value should be tested if we have off mode working + * later on. + */ + mmc3_pins: pinmux_mmc3_pins { + pinctrl-single,pins = < + /* 0x4a10008e gpmc_wait2.gpio_100 d23 */ + OMAP4_IOPAD(0x08e, PIN_INPUT | MUX_MODE3) + + /* 0x4a100102 abe_mcbsp1_dx.sdmmc3_dat2 ab25 */ + OMAP4_IOPAD(0x102, PIN_INPUT_PULLUP | MUX_MODE1) + + /* 0x4a100104 abe_mcbsp1_fsx.sdmmc3_dat3 ac27 */ + OMAP4_IOPAD(0x104, PIN_INPUT_PULLUP | MUX_MODE1) + + /* 0x4a100118 uart2_cts.sdmmc3_clk ab26 */ + OMAP4_IOPAD(0x118, PIN_INPUT | MUX_MODE1) + + /* 0x4a10011a uart2_rts.sdmmc3_cmd ab27 */ + OMAP4_IOPAD(0x11a, PIN_INPUT_PULLUP | MUX_MODE1) + + /* 0x4a10011c uart2_rx.sdmmc3_dat0 aa25 */ + OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE1) + + /* 0x4a10011e uart2_tx.sdmmc3_dat1 aa26 */ + OMAP4_IOPAD(0x11e, PIN_INPUT_PULLUP | MUX_MODE1) + >; + }; + /* gpmc_ncs0.gpio_50 */ poweroff_gpio: pinmux_poweroff_pins { pinctrl-single,pins = < @@ -690,14 +623,18 @@ }; /* - * As uart1 is wired to mdm6600 with rts and cts, we can use the cts pin for - * uart1 wakeirq. + * The uart1 port is wired to mdm6600 with rts and cts. The modem uses gpio_149 + * for wake-up events for both the USB PHY and the UART. We can use gpio_149 + * pad as the shared wakeirq for the UART rather than the RX or CTS pad as we + * have gpio_149 trigger before the UART transfer starts. */ &uart1 { pinctrl-names = "default"; pinctrl-0 = <&uart1_pins>; interrupts-extended = <&wakeupgen GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH - &omap4_pmx_core 0xfc>; + &omap4_pmx_core 0x110>; + uart-has-rtscts; + current-speed = <115200>; }; &uart3 { @@ -757,20 +694,6 @@ "0", "0", "-1"; }; - - lis3dh: accelerometer@18 { - compatible = "st,lis3dh-accel"; - reg = <0x18>; - - vdd-supply = <&vhvio>; - - interrupt-parent = <&gpio2>; - interrupts = <2 IRQ_TYPE_EDGE_BOTH>; /* gpio34 */ - - rotation-matrix = "0", "-1", "0", - "1", "0", "0", - "0", "0", "1"; - }; }; &mcbsp2 { |