diff options
Diffstat (limited to '')
-rw-r--r-- | arch/arm/kernel/hyp-stub.S | 72 |
1 files changed, 20 insertions, 52 deletions
diff --git a/arch/arm/kernel/hyp-stub.S b/arch/arm/kernel/hyp-stub.S index 6607fa817bba..b699b22a4db1 100644 --- a/arch/arm/kernel/hyp-stub.S +++ b/arch/arm/kernel/hyp-stub.S @@ -24,41 +24,38 @@ ENTRY(__boot_cpu_mode) .text /* - * Save the primary CPU boot mode. Requires 3 scratch registers. + * Save the primary CPU boot mode. Requires 2 scratch registers. */ - .macro store_primary_cpu_mode reg1, reg2, reg3 + .macro store_primary_cpu_mode reg1, reg2 mrs \reg1, cpsr and \reg1, \reg1, #MODE_MASK - adr \reg2, .L__boot_cpu_mode_offset - ldr \reg3, [\reg2] - str \reg1, [\reg2, \reg3] + str_l \reg1, __boot_cpu_mode, \reg2 .endm /* * Compare the current mode with the one saved on the primary CPU. * If they don't match, record that fact. The Z bit indicates * if there's a match or not. - * Requires 3 additionnal scratch registers. + * Requires 2 additional scratch registers. */ - .macro compare_cpu_mode_with_primary mode, reg1, reg2, reg3 - adr \reg2, .L__boot_cpu_mode_offset - ldr \reg3, [\reg2] - ldr \reg1, [\reg2, \reg3] + .macro compare_cpu_mode_with_primary mode, reg1, reg2 + adr_l \reg2, __boot_cpu_mode + ldr \reg1, [\reg2] cmp \mode, \reg1 @ matches primary CPU boot mode? orrne \reg1, \reg1, #BOOT_CPU_MODE_MISMATCH - strne \reg1, [\reg2, \reg3] @ record what happened and give up + strne \reg1, [\reg2] @ record what happened and give up .endm #else /* ZIMAGE */ - .macro store_primary_cpu_mode reg1:req, reg2:req, reg3:req + .macro store_primary_cpu_mode reg1:req, reg2:req .endm /* * The zImage loader only runs on one CPU, so we don't bother with mult-CPU * consistency checking: */ - .macro compare_cpu_mode_with_primary mode, reg1, reg2, reg3 + .macro compare_cpu_mode_with_primary mode, reg1, reg2 cmp \mode, \mode .endm @@ -73,7 +70,7 @@ ENTRY(__boot_cpu_mode) */ @ Call this from the primary CPU ENTRY(__hyp_stub_install) - store_primary_cpu_mode r4, r5, r6 + store_primary_cpu_mode r4, r5 ENDPROC(__hyp_stub_install) @ fall through... @@ -87,7 +84,7 @@ ENTRY(__hyp_stub_install_secondary) * If the secondary has booted with a different mode, give up * immediately. */ - compare_cpu_mode_with_primary r4, r5, r6, r7 + compare_cpu_mode_with_primary r4, r5, r6 retne lr /* @@ -189,19 +186,19 @@ ARM_BE8(orr r7, r7, #(1 << 25)) @ HSCTLR.EE ENDPROC(__hyp_stub_install_secondary) __hyp_stub_do_trap: +#ifdef ZIMAGE teq r0, #HVC_SET_VECTORS bne 1f + /* Only the ZIMAGE stubs can change the HYP vectors */ mcr p15, 4, r1, c12, c0, 0 @ set HVBAR b __hyp_stub_exit +#endif 1: teq r0, #HVC_SOFT_RESTART - bne 1f + bne 2f bx r1 -1: teq r0, #HVC_RESET_VECTORS - beq __hyp_stub_exit - - ldr r0, =HVC_STUB_ERR +2: ldr r0, =HVC_STUB_ERR __ERET __hyp_stub_exit: @@ -210,26 +207,9 @@ __hyp_stub_exit: ENDPROC(__hyp_stub_do_trap) /* - * __hyp_set_vectors: Call this after boot to set the initial hypervisor - * vectors as part of hypervisor installation. On an SMP system, this should - * be called on each CPU. - * - * r0 must be the physical address of the new vector table (which must lie in - * the bottom 4GB of physical address space. - * - * r0 must be 32-byte aligned. - * - * Before calling this, you must check that the stub hypervisor is installed - * everywhere, by waiting for any secondary CPUs to be brought up and then - * checking that BOOT_CPU_MODE_HAVE_HYP(__boot_cpu_mode) is true. - * - * If not, there is a pre-existing hypervisor, some CPUs failed to boot, or - * something else went wrong... in such cases, trying to install a new - * hypervisor is unlikely to work as desired. - * - * When you call into your shiny new hypervisor, sp_hyp will contain junk, - * so you will need to set that to something sensible at the new hypervisor's - * initialisation entry point. + * __hyp_set_vectors is only used when ZIMAGE must bounce between HYP + * and SVC. For the kernel itself, the vectors are set once and for + * all by the stubs. */ ENTRY(__hyp_set_vectors) mov r1, r0 @@ -245,18 +225,6 @@ ENTRY(__hyp_soft_restart) ret lr ENDPROC(__hyp_soft_restart) -ENTRY(__hyp_reset_vectors) - mov r0, #HVC_RESET_VECTORS - __HVC(0) - ret lr -ENDPROC(__hyp_reset_vectors) - -#ifndef ZIMAGE -.align 2 -.L__boot_cpu_mode_offset: - .long __boot_cpu_mode - . -#endif - .align 5 ENTRY(__hyp_stub_vectors) __hyp_stub_reset: W(b) . |