diff options
Diffstat (limited to 'arch/arm/mach-orion5x/d2net-setup.c')
| -rw-r--r-- | arch/arm/mach-orion5x/d2net-setup.c | 365 |
1 files changed, 0 insertions, 365 deletions
diff --git a/arch/arm/mach-orion5x/d2net-setup.c b/arch/arm/mach-orion5x/d2net-setup.c deleted file mode 100644 index 8f68b745c1d5..000000000000 --- a/arch/arm/mach-orion5x/d2net-setup.c +++ /dev/null @@ -1,365 +0,0 @@ -/* - * arch/arm/mach-orion5x/d2net-setup.c - * - * LaCie d2Network and Big Disk Network NAS setup - * - * Copyright (C) 2009 Simon Guinot <sguinot@lacie.com> - * - * This file is licensed under the terms of the GNU General Public - * License version 2. This program is licensed "as is" without any - * warranty of any kind, whether express or implied. - */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/platform_device.h> -#include <linux/pci.h> -#include <linux/irq.h> -#include <linux/mtd/physmap.h> -#include <linux/mv643xx_eth.h> -#include <linux/leds.h> -#include <linux/gpio_keys.h> -#include <linux/input.h> -#include <linux/i2c.h> -#include <linux/ata_platform.h> -#include <linux/gpio.h> -#include <asm/mach-types.h> -#include <asm/mach/arch.h> -#include <asm/mach/pci.h> -#include <mach/orion5x.h> -#include <plat/orion-gpio.h> -#include "common.h" -#include "mpp.h" - -/***************************************************************************** - * LaCie d2 Network Info - ****************************************************************************/ - -/* - * 512KB NOR flash Device bus boot chip select - */ - -#define D2NET_NOR_BOOT_BASE 0xfff80000 -#define D2NET_NOR_BOOT_SIZE SZ_512K - -/***************************************************************************** - * 512KB NOR Flash on Boot Device - ****************************************************************************/ - -/* - * TODO: Check write support on flash MX29LV400CBTC-70G - */ - -static struct mtd_partition d2net_partitions[] = { - { - .name = "Full512kb", - .size = MTDPART_SIZ_FULL, - .offset = 0, - .mask_flags = MTD_WRITEABLE, - }, -}; - -static struct physmap_flash_data d2net_nor_flash_data = { - .width = 1, - .parts = d2net_partitions, - .nr_parts = ARRAY_SIZE(d2net_partitions), -}; - -static struct resource d2net_nor_flash_resource = { - .flags = IORESOURCE_MEM, - .start = D2NET_NOR_BOOT_BASE, - .end = D2NET_NOR_BOOT_BASE - + D2NET_NOR_BOOT_SIZE - 1, -}; - -static struct platform_device d2net_nor_flash = { - .name = "physmap-flash", - .id = 0, - .dev = { - .platform_data = &d2net_nor_flash_data, - }, - .num_resources = 1, - .resource = &d2net_nor_flash_resource, -}; - -/***************************************************************************** - * Ethernet - ****************************************************************************/ - -static struct mv643xx_eth_platform_data d2net_eth_data = { - .phy_addr = MV643XX_ETH_PHY_ADDR(8), -}; - -/***************************************************************************** - * I2C devices - ****************************************************************************/ - -/* - * i2c addr | chip | description - * 0x32 | Ricoh 5C372b | RTC - * 0x3e | GMT G762 | PWM fan controller - * 0x50 | HT24LC08 | eeprom (1kB) - * - * TODO: Add G762 support to the g760a driver. - */ -static struct i2c_board_info __initdata d2net_i2c_devices[] = { - { - I2C_BOARD_INFO("rs5c372b", 0x32), - }, { - I2C_BOARD_INFO("24c08", 0x50), - }, -}; - -/***************************************************************************** - * SATA - ****************************************************************************/ - -static struct mv_sata_platform_data d2net_sata_data = { - .n_ports = 2, -}; - -#define D2NET_GPIO_SATA0_POWER 3 -#define D2NET_GPIO_SATA1_POWER 12 - -static void __init d2net_sata_power_init(void) -{ - int err; - - err = gpio_request(D2NET_GPIO_SATA0_POWER, "SATA0 power"); - if (err == 0) { - err = gpio_direction_output(D2NET_GPIO_SATA0_POWER, 1); - if (err) - gpio_free(D2NET_GPIO_SATA0_POWER); - } - if (err) - pr_err("d2net: failed to configure SATA0 power GPIO\n"); - - err = gpio_request(D2NET_GPIO_SATA1_POWER, "SATA1 power"); - if (err == 0) { - err = gpio_direction_output(D2NET_GPIO_SATA1_POWER, 1); - if (err) - gpio_free(D2NET_GPIO_SATA1_POWER); - } - if (err) - pr_err("d2net: failed to configure SATA1 power GPIO\n"); -} - -/***************************************************************************** - * GPIO LED's - ****************************************************************************/ - -/* - * The blue front LED is wired to the CPLD and can blink in relation with the - * SATA activity. - * - * The following array detail the different LED registers and the combination - * of their possible values: - * - * led_off | blink_ctrl | SATA active | LED state - * | | | - * 1 | x | x | off - * 0 | 0 | 0 | off - * 0 | 1 | 0 | blink (rate 300ms) - * 0 | x | 1 | on - * - * Notes: The blue and the red front LED's can't be on at the same time. - * Red LED have priority. - */ - -#define D2NET_GPIO_RED_LED 6 -#define D2NET_GPIO_BLUE_LED_BLINK_CTRL 16 -#define D2NET_GPIO_BLUE_LED_OFF 23 - -static struct gpio_led d2net_leds[] = { - { - .name = "d2net:blue:sata", - .default_trigger = "default-on", - .gpio = D2NET_GPIO_BLUE_LED_OFF, - .active_low = 1, - }, - { - .name = "d2net:red:fail", - .gpio = D2NET_GPIO_RED_LED, - }, -}; - -static struct gpio_led_platform_data d2net_led_data = { - .num_leds = ARRAY_SIZE(d2net_leds), - .leds = d2net_leds, -}; - -static struct platform_device d2net_gpio_leds = { - .name = "leds-gpio", - .id = -1, - .dev = { - .platform_data = &d2net_led_data, - }, -}; - -static void __init d2net_gpio_leds_init(void) -{ - int err; - - /* Configure GPIO over MPP max number. */ - orion_gpio_set_valid(D2NET_GPIO_BLUE_LED_OFF, 1); - - /* Configure register blink_ctrl to allow SATA activity LED blinking. */ - err = gpio_request(D2NET_GPIO_BLUE_LED_BLINK_CTRL, "blue LED blink"); - if (err == 0) { - err = gpio_direction_output(D2NET_GPIO_BLUE_LED_BLINK_CTRL, 1); - if (err) - gpio_free(D2NET_GPIO_BLUE_LED_BLINK_CTRL); - } - if (err) - pr_err("d2net: failed to configure blue LED blink GPIO\n"); - - platform_device_register(&d2net_gpio_leds); -} - -/**************************************************************************** - * GPIO keys - ****************************************************************************/ - -#define D2NET_GPIO_PUSH_BUTTON 18 -#define D2NET_GPIO_POWER_SWITCH_ON 8 -#define D2NET_GPIO_POWER_SWITCH_OFF 9 - -#define D2NET_SWITCH_POWER_ON 0x1 -#define D2NET_SWITCH_POWER_OFF 0x2 - -static struct gpio_keys_button d2net_buttons[] = { - { - .type = EV_SW, - .code = D2NET_SWITCH_POWER_OFF, - .gpio = D2NET_GPIO_POWER_SWITCH_OFF, - .desc = "Power rocker switch (auto|off)", - .active_low = 0, - }, - { - .type = EV_SW, - .code = D2NET_SWITCH_POWER_ON, - .gpio = D2NET_GPIO_POWER_SWITCH_ON, - .desc = "Power rocker switch (on|auto)", - .active_low = 0, - }, - { - .type = EV_KEY, - .code = KEY_POWER, - .gpio = D2NET_GPIO_PUSH_BUTTON, - .desc = "Front Push Button", - .active_low = 0, - }, -}; - -static struct gpio_keys_platform_data d2net_button_data = { - .buttons = d2net_buttons, - .nbuttons = ARRAY_SIZE(d2net_buttons), -}; - -static struct platform_device d2net_gpio_buttons = { - .name = "gpio-keys", - .id = -1, - .dev = { - .platform_data = &d2net_button_data, - }, -}; - -/***************************************************************************** - * General Setup - ****************************************************************************/ - -static unsigned int d2net_mpp_modes[] __initdata = { - MPP0_GPIO, /* Board ID (bit 0) */ - MPP1_GPIO, /* Board ID (bit 1) */ - MPP2_GPIO, /* Board ID (bit 2) */ - MPP3_GPIO, /* SATA 0 power */ - MPP4_UNUSED, - MPP5_GPIO, /* Fan fail detection */ - MPP6_GPIO, /* Red front LED */ - MPP7_UNUSED, - MPP8_GPIO, /* Rear power switch (on|auto) */ - MPP9_GPIO, /* Rear power switch (auto|off) */ - MPP10_UNUSED, - MPP11_UNUSED, - MPP12_GPIO, /* SATA 1 power */ - MPP13_UNUSED, - MPP14_SATA_LED, /* SATA 0 active */ - MPP15_SATA_LED, /* SATA 1 active */ - MPP16_GPIO, /* Blue front LED blink control */ - MPP17_UNUSED, - MPP18_GPIO, /* Front button (0 = Released, 1 = Pushed ) */ - MPP19_UNUSED, - 0, - /* 22: USB port 1 fuse (0 = Fail, 1 = Ok) */ - /* 23: Blue front LED off */ - /* 24: Inhibit board power off (0 = Disabled, 1 = Enabled) */ -}; - -#define D2NET_GPIO_INHIBIT_POWER_OFF 24 - -static void __init d2net_init(void) -{ - /* - * Setup basic Orion functions. Need to be called early. - */ - orion5x_init(); - - orion5x_mpp_conf(d2net_mpp_modes); - - /* - * Configure peripherals. - */ - orion5x_ehci0_init(); - orion5x_eth_init(&d2net_eth_data); - orion5x_i2c_init(); - orion5x_uart0_init(); - - d2net_sata_power_init(); - orion5x_sata_init(&d2net_sata_data); - - mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET, - ORION_MBUS_DEVBUS_BOOT_ATTR, - D2NET_NOR_BOOT_BASE, - D2NET_NOR_BOOT_SIZE); - platform_device_register(&d2net_nor_flash); - - platform_device_register(&d2net_gpio_buttons); - - d2net_gpio_leds_init(); - - pr_notice("d2net: Flash write are not yet supported.\n"); - - i2c_register_board_info(0, d2net_i2c_devices, - ARRAY_SIZE(d2net_i2c_devices)); - - orion_gpio_set_valid(D2NET_GPIO_INHIBIT_POWER_OFF, 1); -} - -/* Warning: LaCie use a wrong mach-type (0x20e=526) in their bootloader. */ - -#ifdef CONFIG_MACH_D2NET -MACHINE_START(D2NET, "LaCie d2 Network") - .atag_offset = 0x100, - .init_machine = d2net_init, - .map_io = orion5x_map_io, - .init_early = orion5x_init_early, - .init_irq = orion5x_init_irq, - .init_time = orion5x_timer_init, - .fixup = tag_fixup_mem32, - .restart = orion5x_restart, -MACHINE_END -#endif - -#ifdef CONFIG_MACH_BIGDISK -MACHINE_START(BIGDISK, "LaCie Big Disk Network") - .atag_offset = 0x100, - .init_machine = d2net_init, - .map_io = orion5x_map_io, - .init_early = orion5x_init_early, - .init_irq = orion5x_init_irq, - .init_time = orion5x_timer_init, - .fixup = tag_fixup_mem32, - .restart = orion5x_restart, -MACHINE_END -#endif - |