diff options
Diffstat (limited to 'arch/arm/mach-pxa/pcm990-baseboard.c')
| -rw-r--r-- | arch/arm/mach-pxa/pcm990-baseboard.c | 203 |
1 files changed, 139 insertions, 64 deletions
diff --git a/arch/arm/mach-pxa/pcm990-baseboard.c b/arch/arm/mach-pxa/pcm990-baseboard.c index 49d951db0f3d..30023b00e476 100644 --- a/arch/arm/mach-pxa/pcm990-baseboard.c +++ b/arch/arm/mach-pxa/pcm990-baseboard.c @@ -24,6 +24,7 @@ #include <linux/platform_device.h> #include <linux/ide.h> #include <linux/i2c.h> +#include <linux/pwm_backlight.h> #include <media/soc_camera.h> @@ -32,13 +33,120 @@ #include <asm/arch/camera.h> #include <asm/mach/map.h> #include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-gpio.h> +#include <asm/arch/audio.h> #include <asm/arch/mmc.h> #include <asm/arch/ohci.h> #include <asm/arch/pcm990_baseboard.h> +#include <asm/arch/pxafb.h> +#include <asm/arch/mfp-pxa27x.h> + +#include "devices.h" +#include "generic.h" + +static unsigned long pcm990_pin_config[] __initdata = { + /* MMC */ + GPIO32_MMC_CLK, + GPIO112_MMC_CMD, + GPIO92_MMC_DAT_0, + GPIO109_MMC_DAT_1, + GPIO110_MMC_DAT_2, + GPIO111_MMC_DAT_3, + /* USB */ + GPIO88_USBH1_PWR, + GPIO89_USBH1_PEN, + /* PWM0 */ + GPIO16_PWM0_OUT, +}; /* - * The PCM-990 development baseboard uses PCM-027's hardeware in the + * pcm990_lcd_power - control power supply to the LCD + * @on: 0 = switch off, 1 = switch on + * + * Called by the pxafb driver + */ +#ifndef CONFIG_PCM990_DISPLAY_NONE +static void pcm990_lcd_power(int on, struct fb_var_screeninfo *var) +{ + if (on) { + /* enable LCD-Latches + * power on LCD + */ + __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG3) = + PCM990_CTRL_LCDPWR + PCM990_CTRL_LCDON; + } else { + /* disable LCD-Latches + * power off LCD + */ + __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG3) = 0x00; + } +} +#endif + +#if defined(CONFIG_PCM990_DISPLAY_SHARP) +static struct pxafb_mode_info fb_info_sharp_lq084v1dg21 = { + .pixclock = 28000, + .xres = 640, + .yres = 480, + .bpp = 16, + .hsync_len = 20, + .left_margin = 103, + .right_margin = 47, + .vsync_len = 6, + .upper_margin = 28, + .lower_margin = 5, + .sync = 0, + .cmap_greyscale = 0, +}; + +static struct pxafb_mach_info pcm990_fbinfo __initdata = { + .modes = &fb_info_sharp_lq084v1dg21, + .num_modes = 1, + .lccr0 = LCCR0_PAS, + .lccr3 = LCCR3_PCP, + .pxafb_lcd_power = pcm990_lcd_power, +}; +#elif defined(CONFIG_PCM990_DISPLAY_NEC) +struct pxafb_mode_info fb_info_nec_nl6448bc20_18d = { + .pixclock = 39720, + .xres = 640, + .yres = 480, + .bpp = 16, + .hsync_len = 32, + .left_margin = 16, + .right_margin = 48, + .vsync_len = 2, + .upper_margin = 12, + .lower_margin = 17, + .sync = 0, + .cmap_greyscale = 0, +}; + +static struct pxafb_mach_info pcm990_fbinfo __initdata = { + .modes = &fb_info_nec_nl6448bc20_18d, + .num_modes = 1, + .lccr0 = LCCR0_Act, + .lccr3 = LCCR3_PixFlEdg, + .pxafb_lcd_power = pcm990_lcd_power, +}; +#endif + +static struct platform_pwm_backlight_data pcm990_backlight_data = { + .pwm_id = 0, + .max_brightness = 1023, + .dft_brightness = 1023, + .pwm_period_ns = 78770, +}; + +static struct platform_device pcm990_backlight_device = { + .name = "pwm-backlight", + .dev = { + .parent = &pxa27x_device_pwm0.dev, + .platform_data = &pcm990_backlight_data, + }, +}; + +/* + * The PCM-990 development baseboard uses PCM-027's hardware in the * following way: * * - LCD support is in use @@ -185,16 +293,6 @@ static int pcm990_mci_init(struct device *dev, irq_handler_t mci_detect_int, { int err; - /* - * enable GPIO for PXA27x MMC controller - */ - pxa_gpio_mode(GPIO32_MMCCLK_MD); - pxa_gpio_mode(GPIO112_MMCCMD_MD); - pxa_gpio_mode(GPIO92_MMCDAT0_MD); - pxa_gpio_mode(GPIO109_MMCDAT1_MD); - pxa_gpio_mode(GPIO110_MMCDAT2_MD); - pxa_gpio_mode(GPIO111_MMCDAT3_MD); - err = request_irq(PCM027_MMCDET_IRQ, mci_detect_int, IRQF_DISABLED, "MMC card detect", data); if (err) @@ -241,8 +339,6 @@ static struct pxamci_platform_data pcm990_mci_platform_data = { */ static int pcm990_ohci_init(struct device *dev) { - pxa_gpio_mode(PCM990_USB_OVERCURRENT); - pxa_gpio_mode(PCM990_USB_PWR_EN); /* * disable USB port 2 and 3 * power sense is active low @@ -269,23 +365,27 @@ static struct pxaohci_platform_data pcm990_ohci_platform_data = { * PXA27x Camera specific stuff */ #if defined(CONFIG_VIDEO_PXA27x) || defined(CONFIG_VIDEO_PXA27x_MODULE) +static unsigned long pcm990_camera_pin_config[] = { + /* CIF */ + GPIO98_CIF_DD_0, + GPIO105_CIF_DD_1, + GPIO104_CIF_DD_2, + GPIO103_CIF_DD_3, + GPIO95_CIF_DD_4, + GPIO94_CIF_DD_5, + GPIO93_CIF_DD_6, + GPIO108_CIF_DD_7, + GPIO107_CIF_DD_8, + GPIO106_CIF_DD_9, + GPIO42_CIF_MCLK, + GPIO45_CIF_PCLK, + GPIO43_CIF_FV, + GPIO44_CIF_LV, +}; + static int pcm990_pxacamera_init(struct device *dev) { - pxa_gpio_mode(GPIO98_CIF_DD_0_MD); - pxa_gpio_mode(GPIO105_CIF_DD_1_MD); - pxa_gpio_mode(GPIO104_CIF_DD_2_MD); - pxa_gpio_mode(GPIO103_CIF_DD_3_MD); - pxa_gpio_mode(GPIO95_CIF_DD_4_MD); - pxa_gpio_mode(GPIO94_CIF_DD_5_MD); - pxa_gpio_mode(GPIO93_CIF_DD_6_MD); - pxa_gpio_mode(GPIO108_CIF_DD_7_MD); - pxa_gpio_mode(GPIO107_CIF_DD_8_MD); - pxa_gpio_mode(GPIO106_CIF_DD_9_MD); - pxa_gpio_mode(GPIO42_CIF_MCLK_MD); - pxa_gpio_mode(GPIO45_CIF_PCLK_MD); - pxa_gpio_mode(GPIO43_CIF_FV_MD); - pxa_gpio_mode(GPIO44_CIF_LV_MD); - + pxa2xx_mfp_config(ARRAY_AND_SIZE(pcm990_camera_pin_config)); return 0; } @@ -333,36 +433,6 @@ static struct i2c_board_info __initdata pcm990_i2c_devices[] = { #endif /* CONFIG_VIDEO_PXA27x ||CONFIG_VIDEO_PXA27x_MODULE */ /* - * AC97 support - * Note: The connected AC97 mixer also reports interrupts at PCM990_AC97_IRQ - */ -static struct resource pxa27x_ac97_resources[] = { - [0] = { - .start = 0x40500000, - .end = 0x40500000 + 0xfff, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_AC97, - .end = IRQ_AC97, - .flags = IORESOURCE_IRQ, - }, -}; - -static u64 pxa_ac97_dmamask = 0xffffffffUL; - -static struct platform_device pxa27x_device_ac97 = { - .name = "pxa2xx-ac97", - .id = -1, - .dev = { - .dma_mask = &pxa_ac97_dmamask, - .coherent_dma_mask = 0xffffffff, - }, - .num_resources = ARRAY_SIZE(pxa27x_ac97_resources), - .resource = pxa27x_ac97_resources, -}; - -/* * enable generic access to the base board control CPLDs U6 and U7 */ static struct map_desc pcm990_io_desc[] __initdata = { @@ -387,13 +457,18 @@ static struct map_desc pcm990_io_desc[] __initdata = { */ void __init pcm990_baseboard_init(void) { + pxa2xx_mfp_config(ARRAY_AND_SIZE(pcm990_pin_config)); + /* register CPLD access */ - iotable_init(pcm990_io_desc, ARRAY_SIZE(pcm990_io_desc)); + iotable_init(ARRAY_AND_SIZE(pcm990_io_desc)); /* register CPLD's IRQ controller */ pcm990_init_irq(); - platform_device_register(&pxa27x_device_ac97); +#ifndef CONFIG_PCM990_DISPLAY_NONE + set_pxa_fb_info(&pcm990_fbinfo); +#endif + platform_device_register(&pcm990_backlight_device); /* MMC */ pxa_set_mci_info(&pcm990_mci_platform_data); @@ -402,13 +477,13 @@ void __init pcm990_baseboard_init(void) pxa_set_ohci_info(&pcm990_ohci_platform_data); pxa_set_i2c_info(NULL); + pxa_set_ac97_info(NULL); #if defined(CONFIG_VIDEO_PXA27x) || defined(CONFIG_VIDEO_PXA27x_MODULE) pxa_set_camera_info(&pcm990_pxacamera_platform_data); - i2c_register_board_info(0, pcm990_i2c_devices, - ARRAY_SIZE(pcm990_i2c_devices)); + i2c_register_board_info(0, ARRAY_AND_SIZE(pcm990_i2c_devices)); #endif - printk(KERN_INFO"PCM-990 Evaluation baseboard initialized\n"); + printk(KERN_INFO "PCM-990 Evaluation baseboard initialized\n"); } |