1 files changed, 313 insertions, 62 deletions

diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
index a393f57ed2a8..6e1907fa94f0 100644
--- a/arch/arm/mach-ux500/board-mop500.c
+++ b/arch/arm/mach-ux500/board-mop500.c
@@ -17,72 +17,62 @@
 #include <linux/gpio.h>
 #include <linux/amba/bus.h>
 #include <linux/amba/pl022.h>
+#include <linux/amba/serial.h>
 #include <linux/spi/spi.h>
 #include <linux/mfd/ab8500.h>
+#include <linux/regulator/ab8500.h>
 #include <linux/mfd/tc3589x.h>
+#include <linux/mfd/tps6105x.h>
+#include <linux/mfd/ab8500/gpio.h>
+#include <linux/leds-lp5521.h>
+#include <linux/input.h>
+#include <linux/gpio_keys.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 
-#include <plat/pincfg.h>
 #include <plat/i2c.h>
+#include <plat/ste_dma40.h>
 
 #include <mach/hardware.h>
 #include <mach/setup.h>
 #include <mach/devices.h>
 #include <mach/irqs.h>
 
+#include "ste-dma40-db8500.h"
 #include "devices-db8500.h"
-#include "pins-db8500.h"
 #include "board-mop500.h"
 #include "board-mop500-regulators.h"
 
-static pin_cfg_t mop500_pins[] = {
-	/* SSP0 */
-	GPIO143_SSP0_CLK,
-	GPIO144_SSP0_FRM,
-	GPIO145_SSP0_RXD,
-	GPIO146_SSP0_TXD,
-
-	/* I2C */
-	GPIO147_I2C0_SCL,
-	GPIO148_I2C0_SDA,
-	GPIO16_I2C1_SCL,
-	GPIO17_I2C1_SDA,
-	GPIO10_I2C2_SDA,
-	GPIO11_I2C2_SCL,
-	GPIO229_I2C3_SDA,
-	GPIO230_I2C3_SCL,
-
-	/* SKE keypad */
-	GPIO153_KP_I7,
-	GPIO154_KP_I6,
-	GPIO155_KP_I5,
-	GPIO156_KP_I4,
-	GPIO157_KP_O7,
-	GPIO158_KP_O6,
-	GPIO159_KP_O5,
-	GPIO160_KP_O4,
-	GPIO161_KP_I3,
-	GPIO162_KP_I2,
-	GPIO163_KP_I1,
-	GPIO164_KP_I0,
-	GPIO165_KP_O3,
-	GPIO166_KP_O2,
-	GPIO167_KP_O1,
-	GPIO168_KP_O0,
-
-	/* GPIO_EXP_INT */
-	GPIO217_GPIO,
-
-	/* STMPE1601 IRQ */
-	GPIO218_GPIO    | PIN_INPUT_PULLUP,
+static struct ab8500_gpio_platform_data ab8500_gpio_pdata = {
+	.gpio_base		= MOP500_AB8500_GPIO(0),
+	.irq_base		= MOP500_AB8500_VIR_GPIO_IRQ_BASE,
+	/* config_reg is the initial configuration of ab8500 pins.
+	 * The pins can be configured as GPIO or alt functions based
+	 * on value present in GpioSel1 to GpioSel6 and AlternatFunction
+	 * register. This is the array of 7 configuration settings.
+	 * One has to compile time decide these settings. Below is the
+	 * explanation of these setting
+	 * GpioSel1 = 0x00 => Pins GPIO1 to GPIO8 are not used as GPIO
+	 * GpioSel2 = 0x1E => Pins GPIO10 to GPIO13 are configured as GPIO
+	 * GpioSel3 = 0x80 => Pin GPIO24 is configured as GPIO
+	 * GpioSel4 = 0x01 => Pin GPIo25 is configured as GPIO
+	 * GpioSel5 = 0x7A => Pins GPIO34, GPIO36 to GPIO39 are conf as GPIO
+	 * GpioSel6 = 0x00 => Pins GPIO41 & GPIo42 are not configured as GPIO
+	 * AlternaFunction = 0x00 => If Pins GPIO10 to 13 are not configured
+	 * as GPIO then this register selectes the alternate fucntions
+	 */
+	.config_reg		= {0x00, 0x1E, 0x80, 0x01,
+					0x7A, 0x00, 0x00},
 };
 
 static struct ab8500_platform_data ab8500_platdata = {
 	.irq_base	= MOP500_AB8500_IRQ_BASE,
+	.regulator_reg_init = ab8500_regulator_reg_init,
+	.num_regulator_reg_init	= ARRAY_SIZE(ab8500_regulator_reg_init),
 	.regulator	= ab8500_regulators,
 	.num_regulator	= ARRAY_SIZE(ab8500_regulators),
+	.gpio		= &ab8500_gpio_pdata,
 };
 
 static struct resource ab8500_resources[] = {
@@ -103,14 +93,13 @@ struct platform_device ab8500_device = {
 	.resource = ab8500_resources,
 };
 
-static struct pl022_ssp_controller ssp0_platform_data = {
-	.bus_id = 0,
-	/* pl022 not yet supports dma */
-	.enable_dma = 0,
-	/* on this platform, gpio 31,142,144,214 &
-	 * 224 are connected as chip selects
-	 */
-	.num_chipselect = 5,
+/*
+ * TPS61052
+ */
+
+static struct tps6105x_platform_data mop500_tps61052_data = {
+	.mode = TPS6105X_MODE_VOLTAGE,
+	.regulator_data = &tps61052_regulator,
 };
 
 /*
@@ -133,12 +122,86 @@ static struct tc3589x_platform_data mop500_tc35892_data = {
 	.irq_base	= MOP500_EGPIO_IRQ_BASE,
 };
 
-static struct i2c_board_info mop500_i2c0_devices[] = {
+static struct lp5521_led_config lp5521_pri_led[] = {
+       [0] = {
+	       .chan_nr = 0,
+	       .led_current = 0x2f,
+	       .max_current = 0x5f,
+       },
+       [1] = {
+	       .chan_nr = 1,
+	       .led_current = 0x2f,
+	       .max_current = 0x5f,
+       },
+       [2] = {
+	       .chan_nr = 2,
+	       .led_current = 0x2f,
+	       .max_current = 0x5f,
+       },
+};
+
+static struct lp5521_platform_data __initdata lp5521_pri_data = {
+       .label = "lp5521_pri",
+       .led_config     = &lp5521_pri_led[0],
+       .num_channels   = 3,
+       .clock_mode     = LP5521_CLOCK_EXT,
+};
+
+static struct lp5521_led_config lp5521_sec_led[] = {
+       [0] = {
+	       .chan_nr = 0,
+	       .led_current = 0x2f,
+	       .max_current = 0x5f,
+       },
+       [1] = {
+	       .chan_nr = 1,
+	       .led_current = 0x2f,
+	       .max_current = 0x5f,
+       },
+       [2] = {
+	       .chan_nr = 2,
+	       .led_current = 0x2f,
+	       .max_current = 0x5f,
+       },
+};
+
+static struct lp5521_platform_data __initdata lp5521_sec_data = {
+       .label = "lp5521_sec",
+       .led_config     = &lp5521_sec_led[0],
+       .num_channels   = 3,
+       .clock_mode     = LP5521_CLOCK_EXT,
+};
+
+static struct i2c_board_info __initdata mop500_i2c0_devices[] = {
 	{
 		I2C_BOARD_INFO("tc3589x", 0x42),
-		.irq            = NOMADIK_GPIO_TO_IRQ(217),
+		.irq		= NOMADIK_GPIO_TO_IRQ(217),
 		.platform_data  = &mop500_tc35892_data,
 	},
+	/* I2C0 devices only available prior to HREFv60 */
+	{
+		I2C_BOARD_INFO("tps61052", 0x33),
+		.platform_data  = &mop500_tps61052_data,
+	},
+};
+
+#define NUM_PRE_V60_I2C0_DEVICES 1
+
+static struct i2c_board_info __initdata mop500_i2c2_devices[] = {
+	{
+		/* lp5521 LED driver, 1st device */
+		I2C_BOARD_INFO("lp5521", 0x33),
+		.platform_data = &lp5521_pri_data,
+	},
+	{
+		/* lp5521 LED driver, 2st device */
+		I2C_BOARD_INFO("lp5521", 0x34),
+		.platform_data = &lp5521_sec_data,
+	},
+	{
+		/* Light sensor Rohm BH1780GLI */
+		I2C_BOARD_INFO("bh1780", 0x29),
+	},
 };
 
 #define U8500_I2C_CONTROLLER(id, _slsu, _tft, _rft, clk, _sm) \
@@ -178,8 +241,93 @@ static void __init mop500_i2c_init(void)
 	db8500_add_i2c3(&u8500_i2c3_data);
 }
 
+static struct gpio_keys_button mop500_gpio_keys[] = {
+	{
+		.desc			= "SFH7741 Proximity Sensor",
+		.type			= EV_SW,
+		.code			= SW_FRONT_PROXIMITY,
+		.active_low		= 0,
+		.can_disable		= 1,
+	}
+};
+
+static struct regulator *prox_regulator;
+static int mop500_prox_activate(struct device *dev);
+static void mop500_prox_deactivate(struct device *dev);
+
+static struct gpio_keys_platform_data mop500_gpio_keys_data = {
+	.buttons	= mop500_gpio_keys,
+	.nbuttons	= ARRAY_SIZE(mop500_gpio_keys),
+	.enable		= mop500_prox_activate,
+	.disable	= mop500_prox_deactivate,
+};
+
+static struct platform_device mop500_gpio_keys_device = {
+	.name	= "gpio-keys",
+	.id	= 0,
+	.dev	= {
+		.platform_data	= &mop500_gpio_keys_data,
+	},
+};
+
+static int mop500_prox_activate(struct device *dev)
+{
+	prox_regulator = regulator_get(&mop500_gpio_keys_device.dev,
+						"vcc");
+	if (IS_ERR(prox_regulator)) {
+		dev_err(&mop500_gpio_keys_device.dev,
+			"no regulator\n");
+		return PTR_ERR(prox_regulator);
+	}
+	regulator_enable(prox_regulator);
+	return 0;
+}
+
+static void mop500_prox_deactivate(struct device *dev)
+{
+	regulator_disable(prox_regulator);
+	regulator_put(prox_regulator);
+}
+
 /* add any platform devices here - TODO */
 static struct platform_device *platform_devs[] __initdata = {
+	&mop500_gpio_keys_device,
+};
+
+#ifdef CONFIG_STE_DMA40
+static struct stedma40_chan_cfg ssp0_dma_cfg_rx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_PERIPH_TO_MEM,
+	.src_dev_type =  DB8500_DMA_DEV8_SSP0_RX,
+	.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg ssp0_dma_cfg_tx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_MEM_TO_PERIPH,
+	.src_dev_type = STEDMA40_DEV_SRC_MEMORY,
+	.dst_dev_type = DB8500_DMA_DEV8_SSP0_TX,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+#endif
+
+static struct pl022_ssp_controller ssp0_platform_data = {
+	.bus_id = 0,
+#ifdef CONFIG_STE_DMA40
+	.enable_dma = 1,
+	.dma_filter = stedma40_filter,
+	.dma_rx_param = &ssp0_dma_cfg_rx,
+	.dma_tx_param = &ssp0_dma_cfg_tx,
+#else
+	.enable_dma = 0,
+#endif
+	/* on this platform, gpio 31,142,144,214 &
+	 * 224 are connected as chip selects
+	 */
+	.num_chipselect = 5,
 };
 
 static void __init mop500_spi_init(void)
@@ -187,18 +335,110 @@ static void __init mop500_spi_init(void)
 	db8500_add_ssp0(&ssp0_platform_data);
 }
 
+#ifdef CONFIG_STE_DMA40
+static struct stedma40_chan_cfg uart0_dma_cfg_rx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_PERIPH_TO_MEM,
+	.src_dev_type =  DB8500_DMA_DEV13_UART0_RX,
+	.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg uart0_dma_cfg_tx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_MEM_TO_PERIPH,
+	.src_dev_type = STEDMA40_DEV_SRC_MEMORY,
+	.dst_dev_type = DB8500_DMA_DEV13_UART0_TX,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg uart1_dma_cfg_rx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_PERIPH_TO_MEM,
+	.src_dev_type =  DB8500_DMA_DEV12_UART1_RX,
+	.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg uart1_dma_cfg_tx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_MEM_TO_PERIPH,
+	.src_dev_type = STEDMA40_DEV_SRC_MEMORY,
+	.dst_dev_type = DB8500_DMA_DEV12_UART1_TX,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg uart2_dma_cfg_rx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_PERIPH_TO_MEM,
+	.src_dev_type =  DB8500_DMA_DEV11_UART2_RX,
+	.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+
+static struct stedma40_chan_cfg uart2_dma_cfg_tx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_MEM_TO_PERIPH,
+	.src_dev_type = STEDMA40_DEV_SRC_MEMORY,
+	.dst_dev_type = DB8500_DMA_DEV11_UART2_TX,
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+};
+#endif
+
+static struct amba_pl011_data uart0_plat = {
+#ifdef CONFIG_STE_DMA40
+	.dma_filter = stedma40_filter,
+	.dma_rx_param = &uart0_dma_cfg_rx,
+	.dma_tx_param = &uart0_dma_cfg_tx,
+#endif
+};
+
+static struct amba_pl011_data uart1_plat = {
+#ifdef CONFIG_STE_DMA40
+	.dma_filter = stedma40_filter,
+	.dma_rx_param = &uart1_dma_cfg_rx,
+	.dma_tx_param = &uart1_dma_cfg_tx,
+#endif
+};
+
+static struct amba_pl011_data uart2_plat = {
+#ifdef CONFIG_STE_DMA40
+	.dma_filter = stedma40_filter,
+	.dma_rx_param = &uart2_dma_cfg_rx,
+	.dma_tx_param = &uart2_dma_cfg_tx,
+#endif
+};
+
 static void __init mop500_uart_init(void)
 {
-	db8500_add_uart0();
-	db8500_add_uart1();
-	db8500_add_uart2();
+	db8500_add_uart0(&uart0_plat);
+	db8500_add_uart1(&uart1_plat);
+	db8500_add_uart2(&uart2_plat);
 }
 
-static void __init u8500_init_machine(void)
+static void __init mop500_init_machine(void)
 {
+	int i2c0_devs;
+
+	/*
+	 * The HREFv60 board removed a GPIO expander and routed
+	 * all these GPIO pins to the internal GPIO controller
+	 * instead.
+	 */
+	if (machine_is_hrefv60())
+		mop500_gpio_keys[0].gpio = HREFV60_PROX_SENSE_GPIO;
+	else
+		mop500_gpio_keys[0].gpio = GPIO_PROX_SENSOR;
+
 	u8500_init_devices();
 
-	nmk_config_pins(mop500_pins, ARRAY_SIZE(mop500_pins));
+	mop500_pins_init();
 
 	platform_add_devices(platform_devs, ARRAY_SIZE(platform_devs));
 
@@ -207,12 +447,15 @@ static void __init u8500_init_machine(void)
 	mop500_spi_init();
 	mop500_uart_init();
 
-	mop500_keypad_init();
-
 	platform_device_register(&ab8500_device);
 
-	i2c_register_board_info(0, mop500_i2c0_devices,
-				ARRAY_SIZE(mop500_i2c0_devices));
+	i2c0_devs = ARRAY_SIZE(mop500_i2c0_devices);
+	if (machine_is_hrefv60())
+		i2c0_devs -= NUM_PRE_V60_I2C0_DEVICES;
+
+	i2c_register_board_info(0, mop500_i2c0_devices, i2c0_devs);
+	i2c_register_board_info(2, mop500_i2c2_devices,
+				ARRAY_SIZE(mop500_i2c2_devices));
 }
 
 MACHINE_START(U8500, "ST-Ericsson MOP500 platform")
@@ -222,5 +465,13 @@ MACHINE_START(U8500, "ST-Ericsson MOP500 platform")
 	.init_irq	= ux500_init_irq,
 	/* we re-use nomadik timer here */
 	.timer		= &ux500_timer,
-	.init_machine	= u8500_init_machine,
+	.init_machine	= mop500_init_machine,
+MACHINE_END
+
+MACHINE_START(HREFV60, "ST-Ericsson U8500 Platform HREFv60+")
+	.boot_params	= 0x100,
+	.map_io		= u8500_map_io,
+	.init_irq	= ux500_init_irq,
+	.timer		= &ux500_timer,
+	.init_machine	= mop500_init_machine,
 MACHINE_END