diff options
Diffstat (limited to 'arch/arm/mach-ux500')
| -rw-r--r-- | arch/arm/mach-ux500/Kconfig | 10 | ||||
| -rw-r--r-- | arch/arm/mach-ux500/Makefile | 1 | ||||
| -rw-r--r-- | arch/arm/mach-ux500/board-mop500-audio.c | 1 | ||||
| -rw-r--r-- | arch/arm/mach-ux500/board-mop500-pins.c | 291 | ||||
| -rw-r--r-- | arch/arm/mach-ux500/board-mop500.h | 73 | ||||
| -rw-r--r-- | arch/arm/mach-ux500/cpu-db8500.c | 17 | ||||
| -rw-r--r-- | arch/arm/mach-ux500/cpu.c | 10 | ||||
| -rw-r--r-- | arch/arm/mach-ux500/irqs-board-mop500.h | 55 | ||||
| -rw-r--r-- | arch/arm/mach-ux500/irqs-db8500.h | 125 | ||||
| -rw-r--r-- | arch/arm/mach-ux500/irqs.h | 49 |
10 files changed, 0 insertions, 632 deletions
diff --git a/arch/arm/mach-ux500/Kconfig b/arch/arm/mach-ux500/Kconfig index 0034d2cd6973..b41a42da1505 100644 --- a/arch/arm/mach-ux500/Kconfig +++ b/arch/arm/mach-ux500/Kconfig @@ -11,13 +11,8 @@ config ARCH_U8500 select ARM_GIC select CACHE_L2X0 select CLKSRC_NOMADIK_MTU - select COMMON_CLK - select CPU_V7 - select GENERIC_CLOCKEVENTS select HAVE_ARM_SCU if SMP select HAVE_ARM_TWD if SMP - select HAVE_SMP - select MIGHT_HAVE_CACHE_L2X0 select PINCTRL select PINCTRL_ABX500 select PINCTRL_NOMADIK @@ -73,11 +68,6 @@ config UX500_AUTO_PLATFORM a working kernel. If everything else is disabled, this automatically enables MACH_MOP500. -config MACH_UX500_DT - bool "Generic U8500 support using device tree" - depends on MACH_MOP500 - select USE_OF - endmenu config UX500_DEBUG_UART diff --git a/arch/arm/mach-ux500/Makefile b/arch/arm/mach-ux500/Makefile index d05ba759da30..de544aabf292 100644 --- a/arch/arm/mach-ux500/Makefile +++ b/arch/arm/mach-ux500/Makefile @@ -7,7 +7,6 @@ obj-$(CONFIG_CACHE_L2X0) += cache-l2x0.o obj-$(CONFIG_UX500_SOC_DB8500) += cpu-db8500.o obj-$(CONFIG_MACH_MOP500) += board-mop500-sdi.o \ board-mop500-regulators.o \ - board-mop500-pins.o \ board-mop500-audio.o obj-$(CONFIG_SMP) += platsmp.o headsmp.o obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o diff --git a/arch/arm/mach-ux500/board-mop500-audio.c b/arch/arm/mach-ux500/board-mop500-audio.c index 9309ad4cbd09..b2a0899e7453 100644 --- a/arch/arm/mach-ux500/board-mop500-audio.c +++ b/arch/arm/mach-ux500/board-mop500-audio.c @@ -9,7 +9,6 @@ #include <linux/gpio.h> #include <linux/platform_data/dma-ste-dma40.h> -#include "irqs.h" #include <linux/platform_data/asoc-ux500-msp.h> #include "ste-dma40-db8500.h" diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c deleted file mode 100644 index f63619b69113..000000000000 --- a/arch/arm/mach-ux500/board-mop500-pins.c +++ /dev/null @@ -1,291 +0,0 @@ -/* - * Copyright (C) ST-Ericsson SA 2010 - * - * License terms: GNU General Public License (GPL) version 2 - */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/bug.h> -#include <linux/string.h> -#include <linux/pinctrl/machine.h> -#include <linux/pinctrl/pinconf-generic.h> - -#include <asm/mach-types.h> - -#include "board-mop500.h" - -/* These simply sets bias for pins */ -#define BIAS(a,b) static unsigned long a[] = { b } - -BIAS(abx500_out_lo, PIN_CONF_PACKED(PIN_CONFIG_OUTPUT, 0)); -BIAS(abx500_in_pd, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 1)); -BIAS(abx500_in_nopull, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 0)); - -#define AB8500_MUX_HOG(group, func) \ - PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-ab8500.0", group, func) -#define AB8500_PIN_HOG(pin, conf) \ - PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-ab8500.0", pin, abx500_##conf) - -#define AB8500_MUX_STATE(group, func, dev, state) \ - PIN_MAP_MUX_GROUP(dev, state, "pinctrl-ab8500.0", group, func) -#define AB8500_PIN_STATE(pin, conf, dev, state) \ - PIN_MAP_CONFIGS_PIN(dev, state, "pinctrl-ab8500.0", pin, abx500_##conf) - -#define AB8505_MUX_HOG(group, func) \ - PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-ab8505.0", group, func) -#define AB8505_PIN_HOG(pin, conf) \ - PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-ab8505.0", pin, abx500_##conf) - -#define AB8505_MUX_STATE(group, func, dev, state) \ - PIN_MAP_MUX_GROUP(dev, state, "pinctrl-ab8505.0", group, func) -#define AB8505_PIN_STATE(pin, conf, dev, state) \ - PIN_MAP_CONFIGS_PIN(dev, state, "pinctrl-ab8505.0", pin, abx500_##conf) - -static struct pinctrl_map __initdata ab8500_pinmap[] = { - /* Sysclkreq2 */ - AB8500_MUX_STATE("sysclkreq2_d_1", "sysclkreq", "regulator.35", PINCTRL_STATE_DEFAULT), - AB8500_PIN_STATE("GPIO1_T10", in_nopull, "regulator.35", PINCTRL_STATE_DEFAULT), - /* sysclkreq2 disable, mux in gpio configured in input pulldown */ - AB8500_MUX_STATE("gpio1_a_1", "gpio", "regulator.35", PINCTRL_STATE_SLEEP), - AB8500_PIN_STATE("GPIO1_T10", in_pd, "regulator.35", PINCTRL_STATE_SLEEP), - - /* pins 2 is muxed in GPIO, configured in INPUT PULL DOWN */ - AB8500_MUX_HOG("gpio2_a_1", "gpio"), - AB8500_PIN_HOG("GPIO2_T9", in_pd), - - /* Sysclkreq4 */ - AB8500_MUX_STATE("sysclkreq4_d_1", "sysclkreq", "regulator.36", PINCTRL_STATE_DEFAULT), - AB8500_PIN_STATE("GPIO3_U9", in_nopull, "regulator.36", PINCTRL_STATE_DEFAULT), - /* sysclkreq4 disable, mux in gpio configured in input pulldown */ - AB8500_MUX_STATE("gpio3_a_1", "gpio", "regulator.36", PINCTRL_STATE_SLEEP), - AB8500_PIN_STATE("GPIO3_U9", in_pd, "regulator.36", PINCTRL_STATE_SLEEP), - - /* pins 4 is muxed in GPIO, configured in INPUT PULL DOWN */ - AB8500_MUX_HOG("gpio4_a_1", "gpio"), - AB8500_PIN_HOG("GPIO4_W2", in_pd), - - /* - * pins 6,7,8 and 9 are muxed in YCBCR0123 - * configured in INPUT PULL UP - */ - AB8500_MUX_HOG("ycbcr0123_d_1", "ycbcr"), - AB8500_PIN_HOG("GPIO6_Y18", in_nopull), - AB8500_PIN_HOG("GPIO7_AA20", in_nopull), - AB8500_PIN_HOG("GPIO8_W18", in_nopull), - AB8500_PIN_HOG("GPIO9_AA19", in_nopull), - - /* - * pins 10,11,12 and 13 are muxed in GPIO - * configured in INPUT PULL DOWN - */ - AB8500_MUX_HOG("gpio10_d_1", "gpio"), - AB8500_PIN_HOG("GPIO10_U17", in_pd), - - AB8500_MUX_HOG("gpio11_d_1", "gpio"), - AB8500_PIN_HOG("GPIO11_AA18", in_pd), - - AB8500_MUX_HOG("gpio12_d_1", "gpio"), - AB8500_PIN_HOG("GPIO12_U16", in_pd), - - AB8500_MUX_HOG("gpio13_d_1", "gpio"), - AB8500_PIN_HOG("GPIO13_W17", in_pd), - - /* - * pins 14,15 are muxed in PWM1 and PWM2 - * configured in INPUT PULL DOWN - */ - AB8500_MUX_HOG("pwmout1_d_1", "pwmout"), - AB8500_PIN_HOG("GPIO14_F14", in_pd), - - AB8500_MUX_HOG("pwmout2_d_1", "pwmout"), - AB8500_PIN_HOG("GPIO15_B17", in_pd), - - /* - * pins 16 is muxed in GPIO - * configured in INPUT PULL DOWN - */ - AB8500_MUX_HOG("gpio16_a_1", "gpio"), - AB8500_PIN_HOG("GPIO14_F14", in_pd), - - /* - * pins 17,18,19 and 20 are muxed in AUDIO interface 1 - * configured in INPUT PULL DOWN - */ - AB8500_MUX_HOG("adi1_d_1", "adi1"), - AB8500_PIN_HOG("GPIO17_P5", in_pd), - AB8500_PIN_HOG("GPIO18_R5", in_pd), - AB8500_PIN_HOG("GPIO19_U5", in_pd), - AB8500_PIN_HOG("GPIO20_T5", in_pd), - - /* - * pins 21,22 and 23 are muxed in USB UICC - * configured in INPUT PULL DOWN - */ - AB8500_MUX_HOG("usbuicc_d_1", "usbuicc"), - AB8500_PIN_HOG("GPIO21_H19", in_pd), - AB8500_PIN_HOG("GPIO22_G20", in_pd), - AB8500_PIN_HOG("GPIO23_G19", in_pd), - - /* - * pins 24,25 are muxed in GPIO - * configured in INPUT PULL DOWN - */ - AB8500_MUX_HOG("gpio24_a_1", "gpio"), - AB8500_PIN_HOG("GPIO24_T14", in_pd), - - AB8500_MUX_HOG("gpio25_a_1", "gpio"), - AB8500_PIN_HOG("GPIO25_R16", in_pd), - - /* - * pins 26 is muxed in GPIO - * configured in OUTPUT LOW - */ - AB8500_MUX_HOG("gpio26_d_1", "gpio"), - AB8500_PIN_HOG("GPIO26_M16", out_lo), - - /* - * pins 27,28 are muxed in DMIC12 - * configured in INPUT PULL DOWN - */ - AB8500_MUX_HOG("dmic12_d_1", "dmic"), - AB8500_PIN_HOG("GPIO27_J6", in_pd), - AB8500_PIN_HOG("GPIO28_K6", in_pd), - - /* - * pins 29,30 are muxed in DMIC34 - * configured in INPUT PULL DOWN - */ - AB8500_MUX_HOG("dmic34_d_1", "dmic"), - AB8500_PIN_HOG("GPIO29_G6", in_pd), - AB8500_PIN_HOG("GPIO30_H6", in_pd), - - /* - * pins 31,32 are muxed in DMIC56 - * configured in INPUT PULL DOWN - */ - AB8500_MUX_HOG("dmic56_d_1", "dmic"), - AB8500_PIN_HOG("GPIO31_F5", in_pd), - AB8500_PIN_HOG("GPIO32_G5", in_pd), - - /* - * pins 34 is muxed in EXTCPENA - * configured INPUT PULL DOWN - */ - AB8500_MUX_HOG("extcpena_d_1", "extcpena"), - AB8500_PIN_HOG("GPIO34_R17", in_pd), - - /* - * pins 35 is muxed in GPIO - * configured in OUTPUT LOW - */ - AB8500_MUX_HOG("gpio35_d_1", "gpio"), - AB8500_PIN_HOG("GPIO35_W15", in_pd), - - /* - * pins 36,37,38 and 39 are muxed in GPIO - * configured in INPUT PULL DOWN - */ - AB8500_MUX_HOG("gpio36_a_1", "gpio"), - AB8500_PIN_HOG("GPIO36_A17", in_pd), - - AB8500_MUX_HOG("gpio37_a_1", "gpio"), - AB8500_PIN_HOG("GPIO37_E15", in_pd), - - AB8500_MUX_HOG("gpio38_a_1", "gpio"), - AB8500_PIN_HOG("GPIO38_C17", in_pd), - - AB8500_MUX_HOG("gpio39_a_1", "gpio"), - AB8500_PIN_HOG("GPIO39_E16", in_pd), - - /* - * pins 40 and 41 are muxed in MODCSLSDA - * configured INPUT PULL DOWN - */ - AB8500_MUX_HOG("modsclsda_d_1", "modsclsda"), - AB8500_PIN_HOG("GPIO40_T19", in_pd), - AB8500_PIN_HOG("GPIO41_U19", in_pd), - - /* - * pins 42 is muxed in GPIO - * configured INPUT PULL DOWN - */ - AB8500_MUX_HOG("gpio42_a_1", "gpio"), - AB8500_PIN_HOG("GPIO42_U2", in_pd), -}; - -static struct pinctrl_map __initdata ab8505_pinmap[] = { - /* Sysclkreq2 */ - AB8505_MUX_STATE("sysclkreq2_d_1", "sysclkreq", "regulator.36", PINCTRL_STATE_DEFAULT), - AB8505_PIN_STATE("GPIO1_N4", in_nopull, "regulator.36", PINCTRL_STATE_DEFAULT), - /* sysclkreq2 disable, mux in gpio configured in input pulldown */ - AB8505_MUX_STATE("gpio1_a_1", "gpio", "regulator.36", PINCTRL_STATE_SLEEP), - AB8505_PIN_STATE("GPIO1_N4", in_pd, "regulator.36", PINCTRL_STATE_SLEEP), - - /* pins 2 is muxed in GPIO, configured in INPUT PULL DOWN */ - AB8505_MUX_HOG("gpio2_a_1", "gpio"), - AB8505_PIN_HOG("GPIO2_R5", in_pd), - - /* Sysclkreq4 */ - AB8505_MUX_STATE("sysclkreq4_d_1", "sysclkreq", "regulator.37", PINCTRL_STATE_DEFAULT), - AB8505_PIN_STATE("GPIO3_P5", in_nopull, "regulator.37", PINCTRL_STATE_DEFAULT), - /* sysclkreq4 disable, mux in gpio configured in input pulldown */ - AB8505_MUX_STATE("gpio3_a_1", "gpio", "regulator.37", PINCTRL_STATE_SLEEP), - AB8505_PIN_STATE("GPIO3_P5", in_pd, "regulator.37", PINCTRL_STATE_SLEEP), - - AB8505_MUX_HOG("gpio10_d_1", "gpio"), - AB8505_PIN_HOG("GPIO10_B16", in_pd), - - AB8505_MUX_HOG("gpio11_d_1", "gpio"), - AB8505_PIN_HOG("GPIO11_B17", in_pd), - - AB8505_MUX_HOG("gpio13_d_1", "gpio"), - AB8505_PIN_HOG("GPIO13_D17", in_nopull), - - AB8505_MUX_HOG("pwmout1_d_1", "pwmout"), - AB8505_PIN_HOG("GPIO14_C16", in_pd), - - AB8505_MUX_HOG("adi2_d_1", "adi2"), - AB8505_PIN_HOG("GPIO17_P2", in_pd), - AB8505_PIN_HOG("GPIO18_N3", in_pd), - AB8505_PIN_HOG("GPIO19_T1", in_pd), - AB8505_PIN_HOG("GPIO20_P3", in_pd), - - AB8505_MUX_HOG("gpio34_a_1", "gpio"), - AB8505_PIN_HOG("GPIO34_H14", in_pd), - - AB8505_MUX_HOG("modsclsda_d_1", "modsclsda"), - AB8505_PIN_HOG("GPIO40_J15", in_pd), - AB8505_PIN_HOG("GPIO41_J14", in_pd), - - AB8505_MUX_HOG("gpio50_d_1", "gpio"), - AB8505_PIN_HOG("GPIO50_L4", in_nopull), - - AB8505_MUX_HOG("resethw_d_1", "resethw"), - AB8505_PIN_HOG("GPIO52_D16", in_pd), - - AB8505_MUX_HOG("service_d_1", "service"), - AB8505_PIN_HOG("GPIO53_D15", in_pd), -}; - -void __init mop500_pinmaps_init(void) -{ - if (machine_is_u8520()) - pinctrl_register_mappings(ab8505_pinmap, - ARRAY_SIZE(ab8505_pinmap)); - else - pinctrl_register_mappings(ab8500_pinmap, - ARRAY_SIZE(ab8500_pinmap)); -} - -void __init snowball_pinmaps_init(void) -{ - pinctrl_register_mappings(ab8500_pinmap, - ARRAY_SIZE(ab8500_pinmap)); -} - -void __init hrefv60_pinmaps_init(void) -{ - pinctrl_register_mappings(ab8500_pinmap, - ARRAY_SIZE(ab8500_pinmap)); -} diff --git a/arch/arm/mach-ux500/board-mop500.h b/arch/arm/mach-ux500/board-mop500.h index d48e8662c676..32cc0d8d8a0e 100644 --- a/arch/arm/mach-ux500/board-mop500.h +++ b/arch/arm/mach-ux500/board-mop500.h @@ -7,78 +7,9 @@ #ifndef __BOARD_MOP500_H #define __BOARD_MOP500_H -/* For NOMADIK_NR_GPIO */ -#include "irqs.h" #include <linux/platform_data/asoc-ux500-msp.h> #include <linux/amba/mmci.h> -/* Snowball specific GPIO assignments, this board has no GPIO expander */ -#define SNOWBALL_ACCEL_INT1_GPIO 163 -#define SNOWBALL_ACCEL_INT2_GPIO 164 -#define SNOWBALL_MAGNET_DRDY_GPIO 165 -#define SNOWBALL_SDMMC_EN_GPIO 217 -#define SNOWBALL_SDMMC_1V8_3V_GPIO 228 -#define SNOWBALL_SDMMC_CD_GPIO 218 - -/* HREFv60-specific GPIO assignments, this board has no GPIO expander */ -#define HREFV60_SDMMC_1V8_3V_GPIO 5 -#define HREFV60_CAMERA_FLASH_ENABLE 21 -#define HREFV60_MAGNET_DRDY_GPIO 32 -#define HREFV60_DISP1_RST_GPIO 65 -#define HREFV60_DISP2_RST_GPIO 66 -#define HREFV60_ACCEL_INT1_GPIO 82 -#define HREFV60_ACCEL_INT2_GPIO 83 -#define HREFV60_SDMMC_CD_GPIO 95 -#define HREFV60_XSHUTDOWN_SECONDARY_SENSOR 140 -#define HREFV60_TOUCH_RST_GPIO 143 -#define HREFV60_HAL_SW_GPIO 145 -#define HREFV60_SDMMC_EN_GPIO 169 -#define HREFV60_MMIO_XENON_CHARGE 170 -#define HREFV60_PROX_SENSE_GPIO 217 - -/* MOP500 generic GPIOs */ -#define CAMERA_FLASH_INT_PIN 7 -#define CYPRESS_TOUCH_INT_PIN 84 -#define XSHUTDOWN_PRIMARY_SENSOR 141 -#define XSHUTDOWN_SECONDARY_SENSOR 142 -#define CYPRESS_TOUCH_RST_GPIO 143 -#define MOP500_HDMI_RST_GPIO 196 -#define CYPRESS_SLAVE_SELECT_GPIO 216 - -/* GPIOs on the TC35892 expander */ -#define MOP500_EGPIO(x) (NOMADIK_NR_GPIO + (x)) -#define GPIO_MAGNET_DRDY MOP500_EGPIO(1) -#define GPIO_SDMMC_CD MOP500_EGPIO(3) -#define GPIO_CAMERA_FLASH_ENABLE MOP500_EGPIO(4) -#define GPIO_MMIO_XENON_CHARGE MOP500_EGPIO(5) -#define GPIO_PROX_SENSOR MOP500_EGPIO(7) -#define GPIO_HAL_SENSOR MOP500_EGPIO(8) -#define GPIO_ACCEL_INT1 MOP500_EGPIO(10) -#define GPIO_ACCEL_INT2 MOP500_EGPIO(11) -#define GPIO_BU21013_CS MOP500_EGPIO(13) -#define MOP500_DISP2_RST_GPIO MOP500_EGPIO(14) -#define MOP500_DISP1_RST_GPIO MOP500_EGPIO(15) -#define GPIO_SDMMC_EN MOP500_EGPIO(17) -#define GPIO_SDMMC_1V8_3V_SEL MOP500_EGPIO(18) -#define MOP500_EGPIO_END MOP500_EGPIO(24) - -/* - * GPIOs on the AB8500 mixed-signals circuit - * Notice that we subtract 1 from the number passed into the macro, this is - * because the AB8500 GPIO pins are enumbered starting from 1, so the value in - * parens matches the GPIO pin number in the data sheet. - */ -#define MOP500_AB8500_PIN_GPIO(x) (MOP500_EGPIO_END + (x) - 1) -/*Snowball AB8500 GPIO */ -#define SNOWBALL_VSMPS2_1V8_GPIO MOP500_AB8500_PIN_GPIO(1) /* SYSCLKREQ2/GPIO1 */ -#define SNOWBALL_PM_GPIO1_GPIO MOP500_AB8500_PIN_GPIO(2) /* SYSCLKREQ3/GPIO2 */ -#define SNOWBALL_WLAN_CLK_REQ_GPIO MOP500_AB8500_PIN_GPIO(3) /* SYSCLKREQ4/GPIO3 */ -#define SNOWBALL_PM_GPIO4_GPIO MOP500_AB8500_PIN_GPIO(4) /* SYSCLKREQ6/GPIO4 */ -#define SNOWBALL_EN_3V6_GPIO MOP500_AB8500_PIN_GPIO(16) /* PWMOUT3/GPIO16 */ -#define SNOWBALL_PME_ETH_GPIO MOP500_AB8500_PIN_GPIO(24) /* SYSCLKREQ7/GPIO24 */ -#define SNOWBALL_EN_3V3_ETH_GPIO MOP500_AB8500_PIN_GPIO(26) /* GPIO26 */ - -struct device; extern struct mmci_platform_data mop500_sdi0_data; extern struct mmci_platform_data mop500_sdi1_data; extern struct mmci_platform_data mop500_sdi2_data; @@ -88,8 +19,4 @@ extern struct msp_i2s_platform_data msp1_platform_data; extern struct msp_i2s_platform_data msp2_platform_data; extern struct msp_i2s_platform_data msp3_platform_data; -void __init mop500_pinmaps_init(void); -void __init snowball_pinmaps_init(void); -void __init hrefv60_pinmaps_init(void); - #endif diff --git a/arch/arm/mach-ux500/cpu-db8500.c b/arch/arm/mach-ux500/cpu-db8500.c index bc8a6183560d..8820f602fcd2 100644 --- a/arch/arm/mach-ux500/cpu-db8500.c +++ b/arch/arm/mach-ux500/cpu-db8500.c @@ -27,7 +27,6 @@ #include <asm/mach/map.h> #include "setup.h" -#include "irqs.h" #include "board-mop500-regulators.h" #include "board-mop500.h" @@ -35,14 +34,11 @@ #include "id.h" struct ab8500_platform_data ab8500_platdata = { - .irq_base = MOP500_AB8500_IRQ_BASE, .regulator = &ab8500_regulator_plat_data, }; struct prcmu_pdata db8500_prcmu_pdata = { .ab_platdata = &ab8500_platdata, - .ab_irq = IRQ_DB8500_AB8500, - .irq_base = IRQ_PRCMU_BASE, .version_offset = DB8500_PRCMU_FW_VERSION_OFFSET, .legacy_offset = DB8500_PRCMU_LEGACY_OFFSET, }; @@ -146,7 +142,6 @@ static struct device * __init db8500_soc_device_init(void) return ux500_soc_device_init(soc_id); } -#ifdef CONFIG_MACH_UX500_DT static struct of_dev_auxdata u8500_auxdata_lookup[] __initdata = { /* Requires call-back bindings. */ OF_DEV_AUXDATA("arm,cortex-a9-pmu", 0, "arm-pmu", &db8500_pmu_platdata), @@ -191,16 +186,6 @@ static void __init u8500_init_machine(void) { struct device *parent = db8500_soc_device_init(); - /* Pinmaps must be in place before devices register */ - if (of_machine_is_compatible("st-ericsson,mop500")) - mop500_pinmaps_init(); - else if (of_machine_is_compatible("calaosystems,snowball-a9500")) { - snowball_pinmaps_init(); - } else if (of_machine_is_compatible("st-ericsson,hrefv60+")) - hrefv60_pinmaps_init(); - else if (of_machine_is_compatible("st-ericsson,ccu9540")) {} - /* TODO: Add pinmaps for ccu9540 board. */ - /* automatically probe child nodes of dbx5x0 devices */ if (of_machine_is_compatible("st-ericsson,u8540")) of_platform_populate(NULL, u8500_local_bus_nodes, @@ -229,5 +214,3 @@ DT_MACHINE_START(U8500_DT, "ST-Ericsson Ux5x0 platform (Device Tree Support)") .dt_compat = stericsson_dt_platform_compat, .restart = ux500_restart, MACHINE_END - -#endif diff --git a/arch/arm/mach-ux500/cpu.c b/arch/arm/mach-ux500/cpu.c index d11ac4bf336c..db16b5a04ad5 100644 --- a/arch/arm/mach-ux500/cpu.c +++ b/arch/arm/mach-ux500/cpu.c @@ -52,17 +52,7 @@ void ux500_restart(enum reboot_mode mode, const char *cmd) */ void __init ux500_init_irq(void) { - void __iomem *dist_base; - void __iomem *cpu_base; - gic_arch_extn.flags = IRQCHIP_SKIP_SET_WAKE | IRQCHIP_MASK_ON_SUSPEND; - - if (cpu_is_u8500_family() || cpu_is_ux540_family()) { - dist_base = __io_address(U8500_GIC_DIST_BASE); - cpu_base = __io_address(U8500_GIC_CPU_BASE); - } else - ux500_unknown_soc(); - irqchip_init(); /* diff --git a/arch/arm/mach-ux500/irqs-board-mop500.h b/arch/arm/mach-ux500/irqs-board-mop500.h deleted file mode 100644 index d526dd8e87d3..000000000000 --- a/arch/arm/mach-ux500/irqs-board-mop500.h +++ /dev/null @@ -1,55 +0,0 @@ -/* - * Copyright (C) ST-Ericsson SA 2010 - * - * Author: Rabin Vincent <rabin.vincent@stericsson.com> - * License terms: GNU General Public License (GPL) version 2 - */ - -#ifndef __MACH_IRQS_BOARD_MOP500_H -#define __MACH_IRQS_BOARD_MOP500_H - -/* Number of AB8500 irqs is taken from header file */ -#include <linux/mfd/abx500/ab8500.h> - -#define MOP500_AB8500_IRQ_BASE IRQ_BOARD_START -#define MOP500_AB8500_IRQ_END (MOP500_AB8500_IRQ_BASE \ - + AB8500_MAX_NR_IRQS) - -/* TC35892 */ -#define TC35892_NR_INTERNAL_IRQS 8 -#define TC35892_INT_GPIO(x) (TC35892_NR_INTERNAL_IRQS + (x)) -#define TC35892_NR_GPIOS 24 -#define TC35892_NR_IRQS TC35892_INT_GPIO(TC35892_NR_GPIOS) - -#define MOP500_EGPIO_NR_IRQS TC35892_NR_IRQS - -#define MOP500_EGPIO_IRQ_BASE MOP500_AB8500_IRQ_END -#define MOP500_EGPIO_IRQ_END (MOP500_EGPIO_IRQ_BASE \ - + MOP500_EGPIO_NR_IRQS) -/* STMPE1601 irqs */ -#define STMPE_NR_INTERNAL_IRQS 9 -#define STMPE_INT_GPIO(x) (STMPE_NR_INTERNAL_IRQS + (x)) -#define STMPE_NR_GPIOS 24 -#define STMPE_NR_IRQS STMPE_INT_GPIO(STMPE_NR_GPIOS) - -#define MOP500_STMPE1601_IRQBASE MOP500_EGPIO_IRQ_END -#define MOP500_STMPE1601_IRQ(x) (MOP500_STMPE1601_IRQBASE + (x)) - -#define MOP500_STMPE1601_IRQ_END \ - MOP500_STMPE1601_IRQ(STMPE_NR_INTERNAL_IRQS) - -#define MOP500_NR_IRQS MOP500_STMPE1601_IRQ_END - -#define MOP500_IRQ_END MOP500_NR_IRQS - -/* - * We may have several boards, but only one will run at a - * time, so the one with most IRQs will bump this ahead, - * but the IRQ_BOARD_START remains the same for either board. - */ -#if MOP500_IRQ_END > IRQ_BOARD_END -#undef IRQ_BOARD_END -#define IRQ_BOARD_END MOP500_IRQ_END -#endif - -#endif diff --git a/arch/arm/mach-ux500/irqs-db8500.h b/arch/arm/mach-ux500/irqs-db8500.h deleted file mode 100644 index f3a9d5947ef3..000000000000 --- a/arch/arm/mach-ux500/irqs-db8500.h +++ /dev/null @@ -1,125 +0,0 @@ -/* - * Copyright (C) ST-Ericsson SA 2010 - * - * Author: Rabin Vincent <rabin.vincent@stericsson.com> - * License terms: GNU General Public License (GPL) version 2 - */ - -#ifndef __MACH_IRQS_DB8500_H -#define __MACH_IRQS_DB8500_H - -#define IRQ_DB8500_MTU0 (IRQ_SHPI_START + 4) -#define IRQ_DB8500_SPI2 (IRQ_SHPI_START + 6) -#define IRQ_DB8500_PMU (IRQ_SHPI_START + 7) -#define IRQ_DB8500_SPI0 (IRQ_SHPI_START + 8) -#define IRQ_DB8500_RTT (IRQ_SHPI_START + 9) -#define IRQ_DB8500_PKA (IRQ_SHPI_START + 10) -#define IRQ_DB8500_UART0 (IRQ_SHPI_START + 11) -#define IRQ_DB8500_I2C3 (IRQ_SHPI_START + 12) -#define IRQ_DB8500_L2CC (IRQ_SHPI_START + 13) -#define IRQ_DB8500_SSP0 (IRQ_SHPI_START + 14) -#define IRQ_DB8500_CRYP1 (IRQ_SHPI_START + 15) -#define IRQ_DB8500_MSP1_RX (IRQ_SHPI_START + 16) -#define IRQ_DB8500_MTU1 (IRQ_SHPI_START + 17) -#define IRQ_DB8500_RTC (IRQ_SHPI_START + 18) -#define IRQ_DB8500_UART1 (IRQ_SHPI_START + 19) -#define IRQ_DB8500_USB_WAKEUP (IRQ_SHPI_START + 20) -#define IRQ_DB8500_I2C0 (IRQ_SHPI_START + 21) -#define IRQ_DB8500_I2C1 (IRQ_SHPI_START + 22) -#define IRQ_DB8500_USBOTG (IRQ_SHPI_START + 23) -#define IRQ_DB8500_DMA_SECURE (IRQ_SHPI_START + 24) -#define IRQ_DB8500_DMA (IRQ_SHPI_START + 25) -#define IRQ_DB8500_UART2 (IRQ_SHPI_START + 26) -#define IRQ_DB8500_ICN_PMU1 (IRQ_SHPI_START + 27) -#define IRQ_DB8500_ICN_PMU2 (IRQ_SHPI_START + 28) -#define IRQ_DB8500_HSIR_EXCEP (IRQ_SHPI_START + 29) -#define IRQ_DB8500_MSP0 (IRQ_SHPI_START + 31) -#define IRQ_DB8500_HSIR_CH0_OVRRUN (IRQ_SHPI_START + 32) -#define IRQ_DB8500_HSIR_CH1_OVRRUN (IRQ_SHPI_START + 33) -#define IRQ_DB8500_HSIR_CH2_OVRRUN (IRQ_SHPI_START + 34) -#define IRQ_DB8500_HSIR_CH3_OVRRUN (IRQ_SHPI_START + 35) -#define IRQ_DB8500_HSIR_CH4_OVRRUN (IRQ_SHPI_START + 36) -#define IRQ_DB8500_HSIR_CH5_OVRRUN (IRQ_SHPI_START + 37) -#define IRQ_DB8500_HSIR_CH6_OVRRUN (IRQ_SHPI_START + 38) -#define IRQ_DB8500_HSIR_CH7_OVRRUN (IRQ_SHPI_START + 39) -#define IRQ_DB8500_AB8500 (IRQ_SHPI_START + 40) -#define IRQ_DB8500_SDMMC2 (IRQ_SHPI_START + 41) -#define IRQ_DB8500_SIA (IRQ_SHPI_START + 42) -#define IRQ_DB8500_SIA2 (IRQ_SHPI_START + 43) -#define IRQ_DB8500_SVA (IRQ_SHPI_START + 44) -#define IRQ_DB8500_SVA2 (IRQ_SHPI_START + 45) -#define IRQ_DB8500_PRCMU0 (IRQ_SHPI_START + 46) -#define IRQ_DB8500_PRCMU1 (IRQ_SHPI_START + 47) -#define IRQ_DB8500_DISP (IRQ_SHPI_START + 48) -#define IRQ_DB8500_SPI3 (IRQ_SHPI_START + 49) -#define IRQ_DB8500_SDMMC1 (IRQ_SHPI_START + 50) -#define IRQ_DB8500_I2C4 (IRQ_SHPI_START + 51) -#define IRQ_DB8500_SSP1 (IRQ_SHPI_START + 52) -#define IRQ_DB8500_SKE (IRQ_SHPI_START + 53) -#define IRQ_DB8500_KB (IRQ_SHPI_START + 54) -#define IRQ_DB8500_I2C2 (IRQ_SHPI_START + 55) -#define IRQ_DB8500_B2R2 (IRQ_SHPI_START + 56) -#define IRQ_DB8500_CRYP0 (IRQ_SHPI_START + 57) -#define IRQ_DB8500_SDMMC3 (IRQ_SHPI_START + 59) -#define IRQ_DB8500_SDMMC0 (IRQ_SHPI_START + 60) -#define IRQ_DB8500_HSEM (IRQ_SHPI_START + 61) -#define IRQ_DB8500_MSP1 (IRQ_SHPI_START + 62) -#define IRQ_DB8500_SBAG (IRQ_SHPI_START + 63) -#define IRQ_DB8500_SPI1 (IRQ_SHPI_START + 96) -#define IRQ_DB8500_SRPTIMER (IRQ_SHPI_START + 97) -#define IRQ_DB8500_MSP2 (IRQ_SHPI_START + 98) -#define IRQ_DB8500_SDMMC4 (IRQ_SHPI_START + 99) -#define IRQ_DB8500_SDMMC5 (IRQ_SHPI_START + 100) -#define IRQ_DB8500_HSIRD0 (IRQ_SHPI_START + 104) -#define IRQ_DB8500_HSIRD1 (IRQ_SHPI_START + 105) -#define IRQ_DB8500_HSITD0 (IRQ_SHPI_START + 106) -#define IRQ_DB8500_HSITD1 (IRQ_SHPI_START + 107) -#define IRQ_DB8500_CTI0 (IRQ_SHPI_START + 108) -#define IRQ_DB8500_CTI1 (IRQ_SHPI_START + 109) -#define IRQ_DB8500_ICN_ERR (IRQ_SHPI_START + 110) -#define IRQ_DB8500_MALI_PPMMU (IRQ_SHPI_START + 112) -#define IRQ_DB8500_MALI_PP (IRQ_SHPI_START + 113) -#define IRQ_DB8500_MALI_GPMMU (IRQ_SHPI_START + 114) -#define IRQ_DB8500_MALI_GP (IRQ_SHPI_START + 115) -#define IRQ_DB8500_MALI (IRQ_SHPI_START + 116) -#define IRQ_DB8500_PRCMU_SEM (IRQ_SHPI_START + 118) -#define IRQ_DB8500_GPIO0 (IRQ_SHPI_START + 119) -#define IRQ_DB8500_GPIO1 (IRQ_SHPI_START + 120) -#define IRQ_DB8500_GPIO2 (IRQ_SHPI_START + 121) -#define IRQ_DB8500_GPIO3 (IRQ_SHPI_START + 122) -#define IRQ_DB8500_GPIO4 (IRQ_SHPI_START + 123) -#define IRQ_DB8500_GPIO5 (IRQ_SHPI_START + 124) -#define IRQ_DB8500_GPIO6 (IRQ_SHPI_START + 125) -#define IRQ_DB8500_GPIO7 (IRQ_SHPI_START + 126) -#define IRQ_DB8500_GPIO8 (IRQ_SHPI_START + 127) - -#define IRQ_CA_WAKE_REQ_ED (IRQ_SHPI_START + 71) -#define IRQ_AC_READ_NOTIFICATION_0_ED (IRQ_SHPI_START + 66) -#define IRQ_AC_READ_NOTIFICATION_1_ED (IRQ_SHPI_START + 64) -#define IRQ_CA_MSG_PEND_NOTIFICATION_0_ED (IRQ_SHPI_START + 67) -#define IRQ_CA_MSG_PEND_NOTIFICATION_1_ED (IRQ_SHPI_START + 65) - -#define IRQ_CA_WAKE_REQ_V1 (IRQ_SHPI_START + 83) -#define IRQ_AC_READ_NOTIFICATION_0_V1 (IRQ_SHPI_START + 78) -#define IRQ_AC_READ_NOTIFICATION_1_V1 (IRQ_SHPI_START + 76) -#define IRQ_CA_MSG_PEND_NOTIFICATION_0_V1 (IRQ_SHPI_START + 79) -#define IRQ_CA_MSG_PEND_NOTIFICATION_1_V1 (IRQ_SHPI_START + 77) - -#ifdef CONFIG_UX500_SOC_DB8500 - -/* Virtual interrupts corresponding to the PRCMU wakeups. */ -#define IRQ_PRCMU_BASE IRQ_SOC_START -#define IRQ_PRCMU_END (IRQ_PRCMU_BASE + 23) - -/* - * We may have several SoCs, but only one will run at a - * time, so the one with most IRQs will bump this ahead, - * but the IRQ_SOC_START remains the same for either SoC. - */ -#if IRQ_SOC_END < IRQ_PRCMU_END -#undef IRQ_SOC_END -#define IRQ_SOC_END IRQ_PRCMU_END -#endif - -#endif /* CONFIG_UX500_SOC_DB8500 */ -#endif diff --git a/arch/arm/mach-ux500/irqs.h b/arch/arm/mach-ux500/irqs.h deleted file mode 100644 index 15b2af698ed7..000000000000 --- a/arch/arm/mach-ux500/irqs.h +++ /dev/null @@ -1,49 +0,0 @@ -/* - * Copyright (C) 2008 STMicroelectronics - * Copyright (C) 2009 ST-Ericsson. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ -#ifndef ASM_ARCH_IRQS_H -#define ASM_ARCH_IRQS_H - -#define IRQ_LOCALTIMER 29 -#define IRQ_LOCALWDOG 30 - -/* Shared Peripheral Interrupt (SHPI) */ -#define IRQ_SHPI_START 32 - -/* - * MTU0 preserved for now until plat-nomadik is taught not to use it. Don't - * add any other IRQs here, use the irqs-dbx500.h files. - */ -#define IRQ_MTU0 (IRQ_SHPI_START + 4) - -#define DBX500_NR_INTERNAL_IRQS 166 - -/* After chip-specific IRQ numbers we have the GPIO ones */ -#define NOMADIK_NR_GPIO 288 -#define NOMADIK_GPIO_TO_IRQ(gpio) ((gpio) + DBX500_NR_INTERNAL_IRQS) -#define NOMADIK_IRQ_TO_GPIO(irq) ((irq) - DBX500_NR_INTERNAL_IRQS) -#define IRQ_GPIO_END NOMADIK_GPIO_TO_IRQ(NOMADIK_NR_GPIO) - -#define IRQ_SOC_START IRQ_GPIO_END -/* This will be overridden by SoC-specific irq headers */ -#define IRQ_SOC_END IRQ_SOC_START - -#include "irqs-db8500.h" - -#define IRQ_BOARD_START IRQ_SOC_END -/* This will be overridden by board-specific irq headers */ -#define IRQ_BOARD_END IRQ_BOARD_START - -#ifdef CONFIG_MACH_MOP500 -#include "irqs-board-mop500.h" -#endif - -#define UX500_NR_IRQS IRQ_BOARD_END - -#endif /* ASM_ARCH_IRQS_H */ |